2012 Toyota Yaris Hatchback Owners Manual

Pulling the lever toward you cancels the constant speed control. The speed setting is also can- celed when the brakes are applied or the clutch pedal (manual transmission only) is depressed. Pushing resumes speed control. Resuming is available when the vehicle speed is more than approximately 25 mph (40
km/h).

lever up constant

the the

159

2-4. Using other driving systems

■Cruise control can be set when

●The shift lever is in the D or range 3. (vehicles with an automatic trans-

mission)

●Vehicle speed is above approximately 25 mph (40 km/h).

■Accelerating after setting the vehicle speed

●The vehicle can be accelerated normally. After acceleration, the set

speed resumes.

●Even without canceling the cruise control, the set speed can be increased by first accelerating the vehicle to the desired speed and then pushing the lever down to set the new speed.

■Automatic cruise control cancelation

Cruise control will stop maintaining the vehicle speed in any of the following situations. ●Actual vehicle speed falls more than approximately 10 mph (16 km/h)

below the preset vehicle speed. At this time, the memorized set speed is not retained.

●Actual vehicle speed is below approximately 25 mph (40 km/h). ●VSC is activated.

■If the cruise control indicator light flashes

Press the “ON-OFF” button once to deactivate the system, and then press the button again to reactivate the system. If the cruise control speed cannot be set or if the cruise control cancels immediately after being activated, there may be a malfunction in the cruise control system. Have the vehicle inspected by your Toyota dealer.

160

2

2-4. Using other driving systems

CAUTION

■To avoid operating the cruise control by mistake

Switch the cruise control off using the “ON-OFF” button when not in use.

■Situations unsuitable for cruise control

Do not use cruise control in any of the following situations. Doing so may result in loss of control and could cause an accident resulting in death or serious injury. ●In heavy traffic ●On roads with sharp bends ●On winding roads ●On slippery roads, such as those covered with rain, ice or snow ●On steep hills

Vehicle speed may exceed the set speed when driving down a steep hill.

●When your vehicle is towing a trailer or during emergency towing

161

2-4. Using other driving systems Driving assist systems

To help enhance driving safety and performance, the following sys- tems operate automatically in response to various driving situations. Be aware, however, that these systems are supplementary and should not be relied upon too heavily when operating the vehicle. ■ ABS (Anti-lock Brake System)

Helps to prevent wheel lock when the brakes are applied suddenly, or if the brakes are applied while driving on a slippery road surface.

■ Brake assist

Generates an increased level of braking force after the brake pedal is depressed when the system detects a panic stop situation.

■ VSC (Vehicle Stability Control)

Helps the driver to control skidding when swerving suddenly or turning on slippery road surfaces.

■ TRAC (Traction Control)

Helps to maintain drive power and prevent the drive wheels from spin- ning when starting the vehicle or accelerating on slippery roads.

■ EPS (Electric Power Steering)

Employs an electric motor to reduce the amount of effort needed to turn the steering wheel.

162

2-4. Using other driving systems

When the TRAC/VSC systems are operating

The slip indicator light flashes to indicate that the TRAC/VSC sys- tems have been engaged.

Disabling the TRAC/VSC systems

If the vehicle gets stuck in fresh snow or mud, TRAC/VSC systems may reduce power from the engine to the wheels. You may need to turn the system off to enable you to rock the vehicle in order to free it. ■ Turning off the TRAC system only

To turn the TRAC system off, quickly press and release the button.

The “TRAC OFF” indicator light will come on. Press the button again to turn the system back on.

163

2-4. Using other driving systems

■ Turning off both TRAC and VSC systems

To turn the TRAC and VSC sys- tems off, press and hold the but- ton for more than 3 seconds while the vehicle is stopped.

The “TRAC OFF” indicator light and VSC OFF indicator light will come on. Press the button again to turn the systems back on.

■When the “TRAC OFF” indicator light comes on even if the VSC OFF

switch has not been pressed TRAC system cannot be operated. Contact your Toyota dealer.

■Sounds and vibrations caused by the ABS, brake assist, VSC and

TRAC ●A sound may be heard from the engine compartment when the engine is started or just after the vehicle begins to move. This sound does not indi- cate that a malfunction has occurred in any of these systems.

●Any of the following conditions may occur when the above systems are

operating. None of these indicates that a malfunction has occurred. • Vibrations may be felt through the vehicle body and steering. • A motor sound may be heard after the vehicle comes to a stop. • The brake pedal may pulsate slightly after the ABS is activated. • The brake pedal may move down slightly after the ABS is activated.

■EPS operation sound

When the steering wheel is operated, a motor sound (whirring sound) may be heard. This does not indicate a malfunction.

■Reactivation of the TRAC/VSC systems after turning off the engine

Turning off the engine after turning off the TRAC/VSC systems will automati- cally reactivate them.

164

2-4. Using other driving systems

■Reactivation of the TRAC system linked to vehicle speed

When only the TRAC system is turned off, the TRAC system will turn on when vehicle speed increases. However, when both TRAC and VSC sys- tems are turned off, the systems will not turn on even when vehicle speed increases.

■Reduced effectiveness of the EPS system

The effectiveness of the EPS system is reduced to prevent the system from overheating when there is frequent steering input over an extended period of time. The steering wheel may feel heavy as a result. Should this occur, refrain from excessive steering input or stop the vehicle and turn the engine off. The EPS system should return to normal within 10 minutes.

■If the slip indicator comes on...

It may indicate a malfunction in the driving assist systems. Contact your Toyota dealer.

CAUTION

■The ABS does not operate effectively when

●Tires with inadequate gripping ability are used (such as excessively worn

tires on a snow covered road).

●The vehicle hydroplanes while driving at high speed on the wet or slick

roads.

■Stopping distance when the ABS is operating may exceed than of nor-

mal conditions The ABS is not designed to shorten the vehicle’s stopping distance. Always maintain a safe distance from the vehicle in front of you in the following situ- ations: ●When driving on dirt, gravel or snow-covered roads ●When driving with tire chains ●When driving over bumps in the road ●When driving over roads with potholes or roads with uneven surfaces

165

2-4. Using other driving systems

CAUTION

■TRAC may not operate effectively when

Directional control and power may not be achievable while driving on slip- pery road surfaces, even if the TRAC system is operating. Be especially careful and drive the vehicle in conditions where stability and power may be lost.

■When the VSC is activated

The slip indicator flashes. Always drive carefully. Reckless driving may cause an accident. Exercise particular care when the indicator light flashes.

■When the TRAC/VSC systems are turned off

Be especially careful and drive at a speed appropriate to the road condi- tions. Do not turn the TRAC/VSC systems off unless necessary, as these are the systems to ensure vehicle stability and driving force by automatically controlling braking and engine outputs.

■Replacing tires

Observe the following precautions. Failure to do so may cause the ABS, VSC and TRAC systems not to function correctly. ●Make sure that all tires are of the specified size, brand, tread pattern and

total load capacity.

●Do not use tires of noticeably different wear level. ●Make sure that the tires are inflated to the recommended tire inflation

pressure level. (→P. 351)

Contact your Toyota dealer for further information when replacing tires or wheels.

■Handling of tires and the suspension

Using tires with any kind of problem or modifying the suspension will affect the driving assist systems, and may cause a system to malfunction.

166

2-5. Driving information Cargo and luggage

Take notice of the following information about storage precau- tions, cargo capacity and load: ● Stow cargo and luggage in the luggage compartment whenever

possible.

● Be sure all items are secured in place. ● To maintain vehicle balance while driving, position luggage

evenly within the luggage compartment.

● For better fuel economy, do not carry unnecessary weight.

Capacity and distribution

Cargo capacity depends on the total weight of the occupants. (Cargo capacity) = (Total load capacity) − (Total weight of occupants) Steps for Determining Correct Load Limit— (1)Locate the statement “The combined weight of occupants and cargo should never exceed XXX kg or XXX lbs.” on your vehicle’s placard.

(2)Determine the combined weight of the driver and passengers that

will be riding in your vehicle.

(3)Subtract the combined weight of the driver and passengers from

XXX kg or XXX lbs.

(4)The resulting figure equals the available amount of cargo and lug-

gage load capacity. For example, if the “XXX” amount equals 1400 lbs. and there will be five 150 lb passengers in your vehicle, the amount of available cargo and luggage load capacity is 650 lbs. (1400 − 750 (5 × 150) = 650 lbs.)

(5)Determine the combined weight of luggage and cargo being loaded on the vehicle. That weight may not safely exceed the available cargo and luggage load capacity calculated in Step 4.

167

2-5. Driving information

(6)If your vehicle will be towing a trailer, load from your trailer will be transferred to your vehicle. Consult this manual to determine how this reduces the available cargo and luggage load capacity of your vehicle. Except 3-door models for Canada: Toyota does not recommend towing a trailer with your vehicle. Your vehicle is not designed for trailer towing.

Example based on your vehicle

Cargo capacity Total load capacity

When 2 people with the combined weight of 366 lb. (166 kg) are riding in your vehicle, which has a total load capacity of 845 lb. (380
kg), the available amount of cargo and luggage load capacity will be as follows: 845 lb. − 366 lb. = 479 lb. (380 kg − 166 kg = 214 kg)

In this condition, if 3 more passengers with the combined weight of 388 lb. (176 kg) get on, the available cargo and luggage load will be reduced as follows:

479 lb. − 388 lb. = 91 lb. (214 kg − 176 kg = 38 kg) As shown in the example above, if the number of occupants increases, the cargo and luggage load will be reduced by an amount that equals the increased weight due to the additional occupants. In other words, if an increase in the number of occupants causes an excess of the total load capacity (combined weight of occupants plus cargo and luggage load), you must reduce the cargo and luggage on your vehicle.

168

2

2-5. Driving information

CAUTION

■Things that must not be carried in the luggage compartment

The following things may cause a fire if loaded in the luggage compart- ment: ●Receptacles containing gasoline ●Aerosol cans

■Storage precautions

Observe the following precautions. Failure to do so may result in death or serious injury. ●Stow cargo and luggage in the luggage compartment whenever possi-

ble.

●Do not stack cargo and luggage in the luggage compartment higher

than the seatbacks. Such items may be thrown about and possibly injure people in the vehicle in the event of sudden braking or in an accident.

●Do not place cargo or luggage in or on the following locations as the item may get under the clutch, brake or accelerator pedal and prevent the pedals from being depressed properly, block the driver’s vision, or hit the driver or passengers, causing an accident: • At the feet of the driver • On the front passenger or rear seats (when stacking items) • On the luggage cover • On the instrument panel • On the dashboard

●Secure all items in the occupant compartment, as they may shift and

injure someone in the event of an accident or sudden braking.

●When you fold down the rear seats, long items should not be place

directly behind the front seats.

●Never allow anyone to ride in the luggage compartment. It is not designed for passengers. They should ride in their seats with their seat belts properly fastened. Otherwise, they are much more likely to suffer death or serious bodily injury, in the event of sudden braking or an accident.

169

2-5. Driving information

CAUTION

■Capacity and distribution

●Do not exceed the maximum axle weight rating or the total vehicle

weight rating.

●Even if the total load of occupant’s weight and the cargo load is less than the total load capacity, do not apply the load unevenly. Improper loading may cause deterioration of steering or braking control which may cause death or serious injury.

170

2-5. Driving information Vehicle load limits

Vehicle load limits include total load capacity, seating capacity, towing capacity and cargo capacity. ■ Total load capacity: 845 lb. (380 kg)

Total load capacity means the combined weight of occupants, cargo and luggage.

■ Seating capacity: 5 occupants (Front 2, Rear 3)

Seating capacity means the maximum number of occupants whose estimated average weight is 150 lb. (68 kg) per person.

■ Towing capacity (3-door models for Canada): 700 lb. (315

kg) Towing capacity means the maximum gross trailer weight (trailer weight plus its cargo weight) that your vehicle is able to tow.

■ Towing capacity (except 3-door models for Canada)

Toyota does not recommend towing a trailer with your vehicle.

■ Cargo capacity

Cargo capacity may increase or decrease depending on the weight and the number of occupants.

■Total load capacity and seating capacity

These details are also described on the tire and loading information label.(→P. 261)

CAUTION

■Overloading the vehicle

Do not overload the vehicle. It may not only cause damage to the tires, but also degrade steering and braking ability, resulting in an accident.

171

2-5. Driving information Winter driving tips

Carry out the necessary preparations and inspections before driving the vehicle in winter. Always drive the vehicle in a manner appropri- ate to the prevailing weather conditions. ■ Pre-winter preparations

● Use fluids that are appropriate to the prevailing outside tem-

peratures. • Engine oil • Engine coolant • Washer fluid

● Have a service technician inspect the level and specific grav-

ity of battery electrolyte.

● Have the vehicle fitted with four snow tires or purchase a set

of tire chains for the front tires. Ensure that all tires are the same size and brand and that their wear level is not noticeably different with each other. Also make sure that chains match the size of the tires.

■ Before driving the vehicle

Perform the following according to the driving conditions: ● Do not try to forcibly open a window or move a wiper that is frozen. Pour warm water over the frozen area to melt the ice. Wipe away the water immediately to prevent it from freezing. ● To ensure proper operation of the climate control system fan, remove any snow that has accumulated on the air inlet vents in front of the windshield.

● Remove any ice that has accumulated on the vehicle chassis. ● Periodically check for and remove any excess ice or snow that may have accumulated in the wheel well or on the brakes.

172

2

2-5. Driving information

■ When driving the vehicle

Accelerate the vehicle slowly and drive at a reduced speed suit- able to the road conditions.

■ When parking the vehicle (in the winter time or in the cold

latitudes) Park the vehicle and move the shift lever to P (vehicles with an automatic transmission) or 1 or R (vehicles with a manual trans- mission) without setting the parking brake. The parking brake may freeze up, preventing it from being released. If necessary, block the wheels to prevent inadvertent sliding or creeping.

Selecting tire chains

Use the correct tire chain size when mounting the tire chains. Chain size is regulated for each tire size.

Side chain 3 mm (0.12 in.) in diameter Cross chain 4 mm (0.16 in.) in diameter

Regulations on the use of tire chains

Regulations regarding the use of tire chains vary depending on loca- tion and type of road. Always check local regulations before installing chains.

173

2-5. Driving information

■Tire chain installation

Observe the following precautions when installing and removing chains: ●Install and remove tire chains in a safe location. ●Install tire chains on the front tires only. Do not install tire chains on the

rear tires.

●Install tire chains on front tires as tightly as possible. Retighten chains

after driving 1/4 - 1/2 mile (0.5 - 1.0 km).

●Install tire chains following the instructions provided with the tire chains. ●If wheel ornaments are used, they will be scratched by the chain band,

so remove the ornaments before putting on the chains. (→P. 317)

CAUTION

■Driving with snow tires

Observe the following precautions to reduce the risk of accidents. Failure to do so may result in a loss of vehicle control and cause death or serious injury. ●Use tires of the size specified. ●Maintain the recommended level of air pressure. ●Do not drive in excess of 75 mph (120 km/h), regardless of the type of

snow tires being used.

●Use snow tires on all, not just some wheels. ●Do not use tires of noticeably different wear level.

174

2

2-5. Driving information

CAUTION

■Driving with tire chains

Observe the following precautions to reduce the risk of accidents. Failure to do so may result in the vehicle being unable to be driven safely, and may cause death or serious injury. ●Do not drive in excess of the speed limit specified for the tire chains being

used, or 30 mph (50 km/h), whichever is lower.

●Avoid driving on bumpy road surfaces or over potholes. ●Avoid sudden turns and braking, as use of chains may adversely affect

vehicle handling.

●Slow down sufficiently before entering a curve to ensure that vehicle con-

trol is maintained.

NOTICE

■Repairing or replacing snow tires (vehicles with a tire pressure warn-

ing system) Request repairs or replacement of snow tires from Toyota dealers or legiti- mate tire retailers. This is because the removal and attachment of snow tires affects the opera- tion of the tire pressure warning valves and transmitters.

■Fitting tire chains (vehicles with a tire pressure warning system)

The tire pressure warning valves and transmitters may not function correctly when tire chains are fitted.

175

2-5. Driving information Trailer towing (except 3-door models for Canada)

Toyota does not recommend towing a trailer with your vehicle. Toyota also does not recommend the installation of a tow hitch or the use of a tow hitch carrier for a wheelchair, scooter, bicycle, etc. Your vehicle is not designed for trailer towing or for the use of tow hitch mounted carriers.

176

2

2-5. Driving information Trailer towing (3-door models for Canada)

Your vehicle is designed primarily as a passenger carrying vehicle. Towing a trailer will have an adverse effect on handling, perfor- mance, braking, durability, and fuel consumption. For your safety and the safety of others, do not overload the vehicle or trailer. To tow a trailer safely, use extreme care and drive the vehicle in accordance with the trailer’s characteristics and operating condi- tions. The vehicle stability and braking performance are affected by trailer stability, brake setting and performance, and the hitch. Toyota warranties do not apply to damage or malfunction caused by towing a trailer for commercial purposes. Contact your Toyota dealer for further information about additional requirements such as a towing kits, etc.

Weight limits

Confirm that the gross trailer weight, gross vehicle weight, gross axle weight and trailer tongue load are all within the limits. ● The gross trailer weight must never exceed 700 lb. (315 kg).

● The gross vehicle weight must never exceed the GVWR indi- cated the Certification Label.

● The gross axle weight on each axle must never exceed the GAWR indicated the Certifica- tion Label.

177

2-5. Driving information

Towing related term

Towing related term

Meaning

GVWR (Gross Vehicle Weight Rating)

GAWR (Gross Axle Weight Rating)

Gross trailer weight

Towing capacity

Tongue load

The maximum allowable gross vehicle weight. The gross vehicle weight is the total weight of the vehicle. When towing a trailer, it is the sum of the vehicle weight (including the occupants, cargo and any optional equipment installed on the vehicle) and the tongue load. The maximum allowable gross axle weight. The gross axle weight is the load placed on each axle (front and rear). The sum of the trailer weight and the weight of the cargo in the trailer The maximum allowable gross trailer weight. Towing capacity is calculated considering the base vehicle with neces- sary vehicle equipment and occupants. Additional optional equipment, passen- gers and cargo in the vehicle will reduce the towing capacity, gross trailer weight include the trailer, cargo and necessary equipment for towing. The load placed on the trailer hitch ball

178

2-5. Driving information

Trailer tongue load

● A recommended tongue load varies in accordance with the types

of trailers or towing as described below.

● In order to ensure the recommended values shown below, the

trailer must be loaded by referring to the following instructions. The trailer cargo load should be distributed so that the tongue load is 9 to 11% of the gross trailer weight, not exceeding 70 lb. (31 kg). (Tongue load / Gross trailer weight x 100 = 9 to 11%)

The gross trailer weight and tongue load can be measured with plat- form scales found at a highway weighing station, building supply company, trucking company, junk yard, etc.

Gross trailer weight Tongue load

Hitch

Trailer hitch assemblies have different weight capacities established by the hitch manufacturer. Even though the vehicle may be rated for towing a higher weight, the operator must never exceed the maxi- mum weight rating specified for the trailer hitch.

Connecting trailer lights

Please consult your dealer when installing trailer lights, as incorrect installation may cause damage to the vehicle’s lights. Please take care to comply with your state’s laws when installing trailer lights.

179

2-5. Driving information

Trailer towing tips

Your vehicle will handle differently when towing a trailer. In order to avoid accident, death or serious injury, keep the following in mind when towing: ● Before starting out, check the trailer lights and the vehicle-trailer

connections. Recheck after driving a short distance.

● Practice turning, stopping and reversing with the trailer attached in an area away from traffic until you become accustomed to the feel of the vehicle.

● Reversing with a trailer attached is difficult and requires practice. Grip the bottom of the steering wheel and move your hand to the left to move the trailer to the left. Move your hand to the right to move the trailer to the right. (This is generally opposite to reversing without a trailer attached.) Avoid sharp or prolonged turning. Have someone guide you when reversing to reduce the risk of an acci- dent.

● As stopping distance is increased when towing a trailer, vehicle-to- vehicle distance should be increased. For each 10 mph (16 km/h) of speed, allow at least one vehicle and trailer length.

● Avoid sudden braking as you may skid, resulting in jackknifing and

loss of control. This is especially true on wet or slippery surfaces.

● Avoid jerky starts or sudden acceleration. Vehicles with a manual transmission, prevent excessive clutch slippage by keeping engine rpm low and not racing the engine. Always start out in first gear.

● Avoid jerky steering and sharp turns, and slow down before mak-

ing turn.

● Note that when making a turn, the trailer wheels will be closer than the vehicle wheels to the inside of the turn. Compensate by making a larger than normal turning radius.

180

2

2-5. Driving information

● Crosswinds and rough roads will adversely affect handling of your vehicle and trailer, causing sway. Periodically check the rear to prepare for being passed by large trucks or buses, which may cause your vehicle and trailer to sway. If swaying occurs, firmly grip the steering wheel, reduce speed immediately but gradually, and steer straight ahead. Never increase speed. If you make no extreme correction with the steering or brakes, your vehicle and trailer will stabilize.

● Take care when passing other vehicles. Passing requires consider- able distance. After passing a vehicle, do not forget the length of your trailer, and be sure you have plenty of room before changing lanes.

● To maintain engine braking efficiency and charging system perfor- mance when using engine braking, do not use the transmission in D (vehicles with an automatic transmission) or 5 (vehicles with a manual transmission).

● Due to the added load of the trailer, your vehicle’s engine may overheat on hot days (at temperatures over 85°F [30°C]) when driving up a long or steep grade. If the high engine coolant temper- ature warning light flashes or comes on overheating, immediately turn off the air conditioning (if in use), pull your vehicle off the road and stop in a safe place. (→P. 334)

181

2-5. Driving information

● Always place wheel blocks under both the vehicle and the trailer wheels when parking. Apply the parking brake firmly, and put the transmission in P (vehicles with an automatic transmission) or in 1
or R (vehicles with a manual transmission). Avoid parking on a slope, but if unavoidable, do so only after performing the following:

Apply the brakes and keep them applied. Have someone place wheel blocks under both the vehicle and trailer wheels. When the wheel blocks are in place, release the brakes slowly until the blocks absorb the load. Apply the parking brake firmly. Shift into P (vehicles with an automatic transmission) or 1 or R (vehicles with a manual transmission) and turn off the engine.

● When restarting after parking on a slope:

With the transmission in P (vehicles with an automatic trans- mission) or the clutch pedal (vehicles with a manual transmis- sion) depressed, start the engine. On vehicles with an automatic transmission, be sure to keep the brake pedal pressed. Shift into a forward gear. If reversing, shift into R. Release the parking brake (also brake pedal on vehicles with an automatic transmission), and slowly pull or back away from the wheel blocks. Stop and apply the brakes. Have someone retrieve the blocks.

182

2

2-5. Driving information

■Before towing

Check that the following conditions are met: ●Ensure that your vehicle’s tires are properly inflated. (→P. 351) ●Trailer tires should be inflated according to the trailer manufacturer’s rec-

ommendation.

●All trailer lights work as required by law. ●All lights work each time you connect them. ●The trailer ball is set at the proper height for the coupler on the trailer. ●The vehicle remains level when a loaded or unloaded trailer is hitched. Do not drive if the vehicle is not level, and check for improper tongue load, overloading, worn suspension, or other possible causes.

●The trailer cargo is securely loaded. ●The rear view mirrors conform to any federal, state/provincial or local regulations. If they do not, install rear view mirrors appropriate for towing purposes.

■Break-in schedule

If your vehicle is new or equipped with any new power train components (such as an engine, transmission, differential and wheel bearing), Toyota recommends that you do not tow a trailer until it has been driven for over 500
miles (800 km). However, avoid full throttle acceleration.

■Maintenance

●If you tow a trailer, your vehicle will require more frequent maintenance due to the additional load. (See “Scheduled Maintenance Guide” or “Owner’s Manual Supplement”.)

●Retighten the fixing bolts of the towing ball and bracket after approxi-

mately 600 miles (1000 km) of trailer towing.

183

2-5. Driving information

CAUTION

■Trailer towing precautions

●Follow all the instructions described in this section. Failure to do so could

cause an accident resulting in death or serious injury.

●Exceeding the towing capacity, GVWR or GAWR can cause an accident

resulting in death or serious personal injuries.

■To avoid accident or injury

●Do not exceed 45 mph (72 km/h) or the posted towing speed limit, which- ever is lower. As instability (swaying) of the towing vehicle-trailer combina- tion increases as speed increases, exceeding 45 mph (72 km/h) may cause loss of control.

●Do not exceed the trailer hitch assembly weight, gross vehicle weight,

gross axle weight and trailer tongue load capacities.

●Never load more weight in the back than in the front of the trailer. About 60% of the load should be in the front half of the trailer, and the remaining 40% in the rear.

●Do not use cruise control when you are towing. ●Slow down and downshift before descending steep or long downhill grades. Do not make sudden downshifts while descending steep or long downhill grades.

●Avoid holding the brake pedal down too long or applying the brakes too frequently. This could cause the brakes to overheat and result in reduced braking efficiency.

●Do not tow the vehicle with the compact spare tire installed.

184

2

2-5. Driving information

CAUTION

■Hitches

Trailer hitch assemblies have different weight capacities established by the hitch manufacturer. Even though the vehicle may be rated for towing a higher weight, the operator must never exceed the maximum weight rating specified for the trailer hitch. ●If you wish to install a trailer hitch, contact your Toyota dealer. ●Use only a hitch that conforms to the gross trailer weight requirement. ●The towing capacity of 700 lb. (315 kg) can only be guaranteed when

using a genuine Toyota hitch assembly or equivalent.

●Follow the directions supplied by the hitch manufacturer. ●Lubricate the hitch ball with a light coat of grease. ●Remove the trailer hitch whenever you are not towing a trailer. After removing the hitch, seal any mounting hole in the vehicle body to prevent entry of any substances into the vehicle.

■When towing a trailer

●Never tap into your vehicle’s hydraulic system, as this will lower the vehi-

cle’s braking effectiveness.

●Never tow a trailer without using a safety chain securely attached to both the trailer and the vehicle. If damage occurs to the coupling unit or hitch ball, there is danger of the trailer wandering into another lane.

185

2-5. Driving information

NOTICE

■When installing a trailer hitch

●Use only the position recommended by your Toyota dealer. Do not install

the trailer hitch on the bumper; this may cause body damage.

●Do not use axle-mounted hitches, as they can cause damage to the axle

housing, wheel bearings, wheels or tires.

■Safety chain

A safety chain must always be used between the towing vehicle and the trailer. Leave sufficient slack in the chain for turns. The chain should cross under the trailer tongue to prevent the tongue from dropping to the ground in the case that it becomes damaged or separated. For the correct safety chain installation procedure, ask your Toyota dealer.

■Do not directly splice trailer lights

Directly splicing trailer lights may damage your vehicle’s electrical system and cause a malfunction.

186

2-5. Driving information Dinghy towing (vehicles with an automatic transmission)

Your vehicle is not designed to be dinghy towed (with 4 wheels on the ground) behind a motor home.

NOTICE

■To avoid serious damage to your vehicle

Do not tow your vehicle with the four wheels on the ground.

187

2-5. Driving information Dinghy towing (vehicles with a manual transmission)

Your vehicle can be dinghy towed in a forward direction (with 4
wheels on the ground) behind a motor home.

Towing your vehicle with 4 wheels on the ground

To prevent damage to your vehicle, perform the following procedures before towing:

Shift the shift lever to N. Turn the engine switch to the “ACC” position. Ensure that the audio system and other powered devices are turned off. Release the parking brake. After towing, leave the engine in idle for at least 3 minutes before driving the vehicle.

■Necessary equipment and accessories

Specialized equipment and accessories are required for dinghy towing. Con- tact the service branch of the motor home manufacturer regarding recom- mended equipment.

188

NOTICE

■Dinghy towing direction

2-5. Driving information

Do not tow the vehicle backward. Doing so may cause serious damage.

■To prevent the steering from locking

Ensure the engine switch is in the “ACC” position.

189

2-5. Driving information

190

3-1. Using the air conditioning system and defogger Air conditioning system

Vehicles without an air conditioning on/off button

Air outlet selector dial

Temperature control dial

Fan speed control dial

Outside/recirculated air mode button

Vehicles with an air conditioning on/off button

Air outlet selector dial

Temperature control dial

Fan speed control dial

Outside/recirculated air mode button

Air conditioning on/off button

192

3-1. Using the air conditioning system and defogger

Adjusting the settings

To adjust the fan speed, turn the fan speed control dial clock- wise (increase) or counterclockwise (decrease). Turning the dial to “0” turns off the fan. Vehicles without an air conditioning on/off button: Turn the temperature control dial clockwise to increase the temperature. Vehicles with an air conditioning on/off button: To adjust the temperature setting, turn the temperature control dial clockwise (warm) or counterclockwise (cool).

is not pressed, the system will blow ambient temperature

If air or heated air. For quick cooling, turn the temperature control dial to “MAX A/C” position and set the outside/recirculated air mode button to recircu- lated air mode. To select the air outlets, set the air outlet selector dial to the desired position. The positions between the air outlet selections shown below can also be selected for more delicate adjustment.

Defogging the windshield

Set the air outlet selector dial to

position. If the recirculated air mode is used, it will automatically switch to the outside air mode. In this position, the outside/recir- culated air mode cannot be changed to the recirculated air mode.

193

3-1. Using the air conditioning system and defogger

Perform the following operations accordingly: ● To adjust the fan speed, turn the fan speed control dial. ● To adjust the temperature setting, turn the temperature con-

trol dial.

● If the dehumidification function is not operating, press

to operate the dehumidification function.

To defog the windshield and the side windows early, turn the air flow and temperature up.

Air outlets and air flow

Air flows to the upper body.

Air flows to the upper body and feet.

: Some models

194

3-1. Using the air conditioning system and defogger

Air flows mainly to the feet.

: Some models

: Some models

Air flows to the feet and the windshield defogger operates.

If the recirculated air mode is used, it will automatically switch to the outside air mode. In this position, the outside/recir- culated air mode cannot be changed to the recirculated air mode.

Switching between outside air and recirculated air modes

Press

The mode switches between outside air mode (introduces air from outside the vehicle) (indicator off) and recirculated air mode (recy- cles air inside the vehicle) (indicator on) each time the button is pressed.

195

3-1. Using the air conditioning system and defogger

Adjusting the position of and opening and closing the air outlets

Center outlets

Direct air flow to the left or right, up or down.

Right and left side outlets

Direct air flow to the left or right, up or down.

Open the vent. Close the vent.

196

3-1. Using the air conditioning system and defogger

■Fogging up of the windows

●The windows will easily fog up when the humidify in the vehicle is high.

Turning windshield effectively. (vehicles with an air conditioning on/off button)

on will dehumidify the air from the outlets and defog the

●If you turn

off, the windows may fog up more easily. (vehicles with

an air conditioning on/off button)

●The windows may fog up if the recirculated air mode is used.

■Outside/recirculated air mode

When driving on dusty roads such as tunnels or in heavy traffic, set the out- side/recirculated air mode button to the recirculated air mode. This is effec- tive in preventing outside air from entering the vehicle interior. During cooling operation, setting the recirculated air mode will also cool the vehicle interior effectively.

■When the indicator light on

goes off by itself (vehicles with an

air conditioning on/off button)

Press to turn off the dehumidification function and turn it on again. There may be a problem in the air conditioning system if the indicator light goes off again. Turn the air conditioning system off and have it inspected by your Toyota dealer.

■When the outside temperature falls to nearly 32°F (0°C) (vehicles with

an air conditioning on/off button)

The dehumidification function may not operate even when pressed.

is

197

3-1. Using the air conditioning system and defogger

■Air conditioning odors

●During use, various odors from inside and outside the vehicle may enter into and accumulate in the air conditioning system. This may then cause odor to be emitted from the vents.

●To reduce potential odors from occurring:

It is recommended that the air conditioning system be set to outside air mode prior to turning the vehicle off.

■Air conditioning filter

→P. 268

CAUTION

■To prevent the windshield from fogging up

Do not use during cool air operation in extremely humid weather. The difference between the temperature of the outside air and that of the wind- shield can cause the outer surface of the windshield to fog up, blocking your vision.

NOTICE

■To prevent battery discharge

Do not leave the air conditioning system on longer than necessary when the engine is stopped.

198

3-1. Using the air conditioning system and defogger Rear window and outside rear view mirror defoggers∗

Defoggers are used to defog the rear window, and to remove rain- drops, dew and frost from the outside rear view mirrors (if equipped).

Turn the defoggers on/off

The defoggers will automati- cally turn off after approxi- mately 15 minutes.

■The defoggers can be operated when The engine switch is in the “ON” position.

■The outside rear view mirror defoggers (if equipped)

Turning the rear window defogger on will turn the outside rear view mirror defoggers on.

CAUTION

■When the outside rear view mirror defoggers are on (if equipped)

Do not touch the outside surface of the rear view mirrors, as they can become very hot and burn you.

∗: If equipped 199

3-2. Using the audio system Using the AUX port/USB port∗

This port can be used to connect a portable audio device and listen to it through the vehicle’s speakers. For more information, please refer to the “Toyota Audio System Owner’s Manual” or “Toyota Navigation System Owner’s Manual”.

Pull up the lever to open the glove box.

Open the cover and connect the portable audio device.

■When using a portable audio device connected to the power outlet

Noise may occur during playback. Use the power source of the portable audio device.

200

∗: If equipped

3-2. Using the audio system Using the steering wheel audio switches∗

Some audio features (audio volume control, radio, CD player etc.) can be controlled using the switches on the steering wheel. For more information, please refer to the ”Toyota Audio System Owner’s Manual” or “Toyota Navigation System Owner’s Manual”.

CAUTION

■To reduce the risk of an accident

Exercise care when operating the audio switches on the steering wheel.

∗: If equipped 201

3-3. Using the interior lights Interior lights list

Personal lights (→P. 203) Interior light (→P. 203)

202

3-3. Using the interior lights

Personal lights and interior light

Personal lights

Turns the lights on/off

Interior light

Turns the lights off Turns the lights on/off linked to door position Turns the lights on

■Illuminated entry system

The lights automatically turn on/off according to the engine switch position, whether the doors are locked/unlocked, and whether the doors are open/ closed.

■To prevent battery discharged

If the interior light remains on when the door is not fully closed and the inte- rior light switch is in the door position, the lights will go off automatically after 20 minutes.

■Customization that can be configured at Toyota dealer

Settings (e.g. the time elapsed before lights turn off) can be changed. (Customizable features →P. 368)

203

3-4. Using the storage features List of storage features

Cup holders Glove box Bottle holders

CAUTION

■Items that should not be left in the storage spaces

Do not leave glasses, lighters or spray cans in the storage spaces, as this may cause the following when cabin temperature becomes high: ●Glasses may be deformed by heat or cracked if they come into contact

with other stored items.

●Lighters or spray cans may explode. If they come into contact with other stored items, the lighter may catch fire or the spray can may release gas, causing a fire hazard.

204

Glove box

3-4. Using the storage features

Glove box and cup holders

Pull up the lever to open the glove box.

CAUTION

■Caution while driving

Keep the glove box closed. In the event of sudden braking, an accident may occur due to an occupant being struck by the open glove box or the items stored inside.

Cup holders

Front

205

3-4. Using the storage features

Rear

Cup holders

■Remove the separator

Pull the separator up.

CAUTION

■Items unsuitable for the cup holder

Do not place anything other than cups or beverage cans in the cup holders. Other items may be thrown out of the holders in the event of an accident or sudden braking, causing injury. If possible, cover hot drinks to prevent burns.

206

3-4. Using the storage features

Bottle holders

Bottle holders

■When using the bottle holder

●When storing a bottle, close the cap. ●The bottle may not be stored depending on its size or shape.

CAUTION

■Items unsuitable for the bottle holder

Do not place anything other than a bottle in the bottle holders. Other items may be thrown out of the holders in the event of an accident or sudden braking and cause injury.

NOTICE

■Items that should not be stowed in the bottle holders

Put the cap on before stowing a bottle. Do not place open bottles in the bot- tle holders, or glasses and paper cups containing liquid. The contents may spill and glasses may break.

207

3-5. Other interior features Sun visors

To set the visor in the for- ward position, flip it down. To set the visor in the side position, flip down, unhook, and swing it to the side. To use the side extender, place the visor in the side position, then slide it back- ward. (if equipped)

208

3-5. Other interior features Vanity mirrors

Slide the cover to open.

209

3-5. Other interior features Clock

Adjusts the hours Adjusts the minutes

■The clock is displayed when

The engine switch is in the “ON” position.

■When disconnecting and reconnecting battery terminals

The clock data will be reset.

210

3-5. Other interior features Outside temperature display

The temperature display shows temperatures within the ranges of -40°F (-40°C) and 122°F (50°C). Except Canada

Canada

211

3-5. Other interior features

■The outside temperature is displayed when

The engine switch is in the “ON” position.

■Display

In the following situations, the correct outside temperature may not be dis- played, or the display may take longer than normal to change: ●When the vehicle is stopped, or moving at low speeds (less than 16 mph

[25 km/h])

●When the outside temperature has changed suddenly (at the entrance/

exit of a garage, tunnel, etc.)

■When “− −” or “E” is displayed

The system may be malfunctioning. Take your vehicle to your Toyota dealer.

212

3-5. Other interior features Power outlet

The power outlet can be used for 12 V accessories that run on less than 10 A.

■The power outlet can be used when

The engine switch is in the “ACC” or “ON” position.

NOTICE

■To avoid damaging the power outlet

Close the power outlet lid when the power outlet is not in use. Foreign objects or liquids that enter the power outlet may cause a short cir- cuit.

■To prevent blown fuse

Do not use an accessory that uses more than 12 V 10 A.

■To prevent battery discharge

Do not use the power outlet longer than necessary when the engine is not running.

213

3-5. Other interior features Floor mat

Use only floor mats designed specifically for vehicles of the same model and model year as your vehicle. Fix them securely in place onto the carpet.

the

Insert retaining hooks (clips) into the floor mat eye- lets.

Turn the upper knob of each retaining hook (clip) to secure the floor mats in place. *: Always align the

marks.

The shape of the retaining hooks (clips) may differ from that shown in the illustration.

214

3-5. Other interior features

CAUTION

Observe the following precautions. Failure to do so may cause the driver’s floor mat to slip, possibly interfering with the pedals while driving. An unexpectedly high speed may result or it may become difficult to stop the vehicle, leading to a serious accident. ■When installing the driver’s floor mat

●Do not use floor mats designed for other models or different model year

vehicles, even if they are Toyota Genuine floor mats.

●Only use floor mats designed for the driver’s seat. ●Always install the floor mat securely using the retaining hooks (clips) pro-

vided.

●Do not use two or more floor mats on top of each other. ●Do not place the floor mat bottom-side up or upside-down.

■Before driving

●Check that the floor mat is securely fixed in the correct place with all the provided retaining hooks (clips). Be especially careful to perform this check after cleaning the floor.

●With the engine stopped and the shift lever in P (vehicles with an automatic transmission) or N (vehicles with a manual fully depress each pedal to the floor to make sure it does not interfere with the floor mat.

transmission),

215

3-5. Other interior features Luggage compartment features

■ Deck board

Removing the deck board

Lift up the deck board and pull it towards you to remove it.

Securing the deck board

Lift up the deck board.

216

3-5. Other interior features

Remove the hook on the back- side of the deck board. Attach the hook to the upper edge of the back door opening as shown.

■Removing the luggage cover

The luggage cover can be removed by the following procedure:

Unhook the cords. Return the luggage cover to horizontal position.

Lift the luggage cover and pull it forward.

217

3-5. Other interior features

CAUTION

■When operating the deck board

Do not place anything on the deck board when operating the board. Other- wise, your fingers may be caught or an accident may result causing injuries.

218

4-1. Maintenance and care Cleaning and protecting the vehicle exterior

Perform the following to protect the vehicle and maintain it in prime condition:

● Working from top to bottom, liberally apply water to the vehicle body, wheel wells and underside of the vehicle to remove any dirt and dust.

● Wash the vehicle body using a sponge or soft cloth, such as a

chamois.

● For hard-to-remove marks, use car wash soap and rinse thor-

oughly with water.

● Wipe away any water. ● Wax the vehicle when the waterproof coating deteriorates.

If water does not bead on a clean surface, apply wax when the vehi- cle body is cool.

■Automatic car washes

●Fold the mirrors and remove the antenna before washing the vehicle. Start washing from the front of the vehicle. Make sure to re-install the antenna and extend the mirrors before driving.

●Brushes used in automatic car washes may scratch the vehicle surface

and harm your vehicle’s paint.

●For vehicles with the rear spoiler, in certain automatic car washes, the rear spoiler may interfere with machine operation. This may prevent the vehicle from being cleaned properly or result in damage to the rear spoiler.

■High pressure car washes

●Do not allow the nozzles of the car wash to come within close proximity

of the window and door borders, and high mounted stoplight.

●Before using the car wash, check that the fuel filler door on your vehicle

is closed properly.

220

4-1. Maintenance and care

■Aluminum wheels (if equipped)

●Remove any dirt immediately by using a neutral detergent. Do not use hard brushes or abrasive cleaners. Do not use strong or harsh chemical cleaners. Use the same mild detergent and wax as used on the paint.

●Do not use detergent on the wheels when they are hot, for example after

driving for long distance in the hot weather.

●Wash detergent from the wheels immediately after use. ●To preserve the wheels’ luster, do not allow hot water, such as from

steam cleaning, to contact them directly.

■Bumpers

Do not scrub with abrasive cleaners.

CAUTION

■When washing the vehicle

Do not apply water to the inside of the engine compartment. Doing so may cause the electrical components etc. to catch fire.

■Precautions regarding the exhaust pipe

Exhaust gasses cause the exhaust pipe to become quite hot. When washing the vehicle, be careful not to touch the pipe until it has cooled sufficiently, as touching a hot exhaust pipe can cause burns.

221

4-1. Maintenance and care

NOTICE

■To prevent paint deterioration and corrosion on the body and compo-

nents (aluminum wheels etc.) ●Wash the vehicle immediately in the following cases:

• After driving near the sea coast • After driving on salted roads • If coal tar or tree sap is present on the paint surface • If dead insects, insect droppings or bird droppings are present on the

paint surface

• After driving in an area contaminated with soot, oily smoke, mine dust,

iron powder or chemical substances

• If the vehicle becomes heavily soiled with dust or mud • If liquids such as benzene and gasoline are spilled on the paint surface

●If the paint is chipped or scratched, have it repaired immediately. ●To prevent the wheels from corroding, remove any dirt and store in a place

with low humidity when storing the wheels.

■Cleaning the exterior lights

●Wash carefully. Do not use organic substances or scrub with a hard brush.

This may damage the surfaces of the lights.

●Do not apply wax to the surfaces of the lights.

Wax may cause damage to the lenses.

■Antenna installation and removal precautions

●Before driving, ensure that the antenna is installed. ●When the antenna is removed, such as before entering an automatic car wash, make sure to store it in a suitable place so as not to lose it. Also, before driving, make sure to reinstall the antenna in its original position.

■To prevent damage to the antenna

Remove the antenna in the following situations: ●When the antenna will touch the ceiling of a garage or other such places ●When a car cover is to be used to cover the vehicle

222

4-1. Maintenance and care Cleaning and protecting the vehicle interior

The following procedures will help protect your vehicle’s interior and keep it in top condition: ■ Protecting the vehicle interior

Remove dirt and dust using a vacuum cleaner. Wipe dirty sur- faces with a cloth dampened with lukewarm water.

■ Cleaning the leather areas

● Remove dirt and dust using a vacuum cleaner. ● Wipe off any excess dirt and dust with a soft cloth dampened

with diluted detergent. Use a diluted water solution of approximately 5% neutral wool deter- gent.

● Wring out any excess water from the cloth and thoroughly

wipe off all remaining traces of detergent.

● Wipe the surface with a dry, soft cloth to remove any remain- ing moisture. Allow the leather to dry in a shaded and venti- lated area.