2-1. Driving procedures
NOTICE
■When driving the vehicle
●Do not depress the accelerator and brake pedals at the same time during
driving, as this may restrain driving torque.
●Do not use the accelerator pedal or depress the accelerator and brake
pedals at the same time to hold the vehicle on a hill.
■Avoiding damage to vehicle parts
●Do not turn the steering wheel fully in either direction and hold it there for
an extended period of time. Doing so may damage the power steering motor.
●When driving over bumps in the road, drive as slowly as possible to avoid
damaging the wheels, underside of the vehicle, etc.
■If you get a flat tire while driving
A flat or damaged tire may cause the following situations. Hold the steering wheel firmly and gradually depress the brake pedal to slow down the vehicle. ●It may be difficult to control your vehicle. ●The vehicle will make abnormal sounds or vibrations. ●The vehicle will lean abnormally. Information on what to do in case of a flat tire. (→P. 460)
171
PRIUS v_U (OM47674U)
2-1. Driving procedures
NOTICE
■When encountering flooded roads
Do not drive on a road that has flooded after heavy rain etc. Doing so may cause the following serious damage to the vehicle: ●Engine stalling ●Short in electrical components ●Engine damage caused by water immersion In the event that you drive on a flooded road and the vehicle is flooded, be sure to have your Toyota dealer check the following: ●Brake function ●Changes in quantity and quality of engine oil, transmission fluid for the
hybrid system, etc.
●Lubricant condition for the bearings and suspension joints (where possi-
ble), and the function of all joints, bearings, etc.
If the P position control system is damaged by flooding, it may not be possi- ble to shift the shift position to P, or from P to other positions. When the shift position cannot be changed from P to any other position, the front wheels will lock, and you will be unable to tow the vehicle with the front wheels on the ground, as the front wheels may be locked. In this case, transport the vehicle with both front wheels or all four wheels lifted.
172
PRIUS v_U (OM47674U)
2
2-1. Driving procedures Power (ignition) switch
Performing the following operations when carrying the electronic key on your person starts the hybrid system or changes “POWER” switch modes. ■ Starting the hybrid system
STEP 1
STEP 2
Check that the parking brake is set. Firmly depress the brake pedal. Check that the “POWER” switch indicator turns green. If the indi- cator does not turn green, the hybrid system cannot be started. When the shift position is N, the hybrid system cannot start. Shift the shift position to P when starting the hybrid system. (→P. 186)
STEP 3
Press the “POWER” switch.
The hybrid system can be started from any “POWER” switch mode. Continue depressing the brake pedal until the hybrid system is completely started.
173
PRIUS v_U (OM47674U)
2-1. Driving procedures
STEP 4
Check that the “READY” indicator is on. If the “READY” indicator changes from a flashing light to a solid light and the buzzer sounds, the hybrid system is starting nor- mally. The vehicle will not move when the “READY” indicator is off. The vehicle can move when the “READY” indicator is on even if the engine is stopped. (The gasoline engine starts or stops auto- matically in accordance with the state of the vehicle.)
■ Stopping the hybrid system
STEP 1
STEP 2
STEP 3
STEP 4
STEP 5
Stop the vehicle completely. Set the parking brake. (→P. 193) Shift the shift position to P. (→P. 186) Check that the shift position indicator shows P. (→P. 183) Press the “POWER” switch. The hybrid system will stop. Slowly release the brake pedal and check that the indicator on the “POWER” switch is off.
174
PRIUS v_U (OM47674U)
2
2-1. Driving procedures
■ Changing “POWER” switch modes Modes can be changed by pressing the “POWER” switch with the brake pedal released. (The mode changes each time the switch is pressed.)
Off The emergency flashers can be used. ACCESSORY mode Some electrical components such as the audio system can be used. The “POWER” switch indicator turns amber. ON mode All electrical components can be used. The “POWER” switch indicator turns amber.
175
PRIUS v_U (OM47674U)
2-1. Driving procedures
■Auto power off function
If the vehicle is left in ACCESSORY or ON mode (the hybrid system is not operating) for more than an hour with the shift position in P, the “POWER” switch will automatically turn off. However, this function cannot entirely pre- vent the 12-volt battery from discharging. Do not leave the vehicle with the “POWER” switch in ACCESSORY or ON mode for long periods of time when the hybrid system is not operating.
■Sounds and vibrations specific to a hybrid vehicle
→P. 32
■Electronic key battery depletion
→P. 66
■When the ambient temperature is low, such as during winter driving
conditions The “READY” indicator may flash for a long time when the hybrid system is starting. Driving will become possible once the “READY” indicator has illumi- nated. Wait until the “READY” indicator has illuminated.
■Conditions affecting operation
→P. 62
■Notes for the entry function
→P. 63
■If the hybrid system does not start
The immobilizer system may not have been deactivated. (→P. 116)
176
PRIUS v_U (OM47674U)
2
2-1. Driving procedures
■When the “POWER” switch indicator flashes in amber
The system may be malfunctioning. Have the vehicle inspected by your Toyota dealer immediately.
■If the “READY” indicator does not come on
If the “READY” indicator does not come on when you press the “POWER” switch with the shift position in P and the brake pedal depressed, contact your Toyota dealer immediately.
■If the hybrid system is malfunctioning
→P. 443
■If the electronic key battery is depleted
→P. 406
■Operation of the “POWER” switch
●When operating the “POWER” switch, one short, firm press is enough. If the switch is pressed improperly, the hybrid system may not start or the “POWER” switch mode may not change. It is not necessary to press and hold the switch.
●If attempting to restart the hybrid system immediately after turning the “POWER” switch off, the hybrid system may not start in some cases. After turning the “POWER” switch off, please wait a few seconds before restarting the hybrid system.
■Automatically P position selection function
→P. 188
177
PRIUS v_U (OM47674U)
2-1. Driving procedures
■When the P position control system malfunctions
The “POWER” switch will not be able to be turned off. In such a case, the switch can be turned off after applying the parking brake. Have the vehicle inspected by your Toyota dealer immediately.
■Meter display
When the “POWER” switch is turned off, each display will extinguish as fol-
lows.
●The shift position indicator will extinguish after approximately 2 seconds.
●The odometer, clock, etc. will extinguish after approximately 30 seconds.
(Each display will also extinguish immediately if a door is locked before 30
seconds has elapsed)
CAUTION
■When starting the hybrid system
Always start the hybrid system while sitting in the driver’s seat. Do not depress the accelerator pedal while starting the hybrid system under any cir- cumstances. Doing so may cause an accident resulting in death or serious injury.
■Stopping the hybrid system in an emergency
If you want to stop the hybrid system in an emergency while driving the vehi- cle, press and hold the “POWER” switch for more than 3 seconds, or press it briefly 3 times or more in succession. However, do not touch the “POWER” switch while driving except in an emer- gency. Turning the hybrid system off while driving will not cause loss of steering or braking control, but the power assist to these systems will be lost. This will make it more difficult to steer and brake, so you should pull over and stop the vehicle as soon as it is safe to do so.
178
PRIUS v_U (OM47674U)
2-1. Driving procedures
NOTICE
■To prevent 12-volt battery discharge
●Do not leave the “POWER” switch in ACCESSORY or ON mode for long
periods of time without the hybrid system on.
●If the hybrid system is off, but the indicator on the “POWER” switch is illu- minated, this indicates that the “POWER” switch is still turned on. When exiting the vehicle, always check that the “POWER” switch is off. ■Symptoms indicating a malfunction with the “POWER” switch
If the “POWER” switch seems to be operating somewhat differently than usual, such as the switch sticking slightly, there may be a malfunction. Con- tact your Toyota dealer immediately.
179
PRIUS v_U (OM47674U)
2-1. Driving procedures EV drive mode
In EV drive mode, the electric motor (traction motor), powered by the hybrid battery (traction battery), is used to drive the vehicle. This mode allows you to drive in residential areas late at night, or in indoor parking lots etc. without concern for noises and exhaust gas emissions.
Turns EV drive mode on/off
When EV drive mode is turned on, the EV drive mode indica- tor will come on. Pressing the switch when in EV drive mode will return the vehicle to normal driving (using the gasoline engine and elec- tric motor [traction motor]).
180
PRIUS v_U (OM47674U)
2
2-1. Driving procedures
■Situations in which EV drive mode cannot be turned on It may not be possible to turn EV drive mode on in the following situations.* If it cannot be turned on, a buzzer will sound and the EV drive mode indica- tor will flash and go off. ●The temperature of the hybrid system is high.
The vehicle has been left in the sun, driven on a hill, driven at high speeds, etc.
●The temperature of the hybrid system is low.
The vehicle has been left in temperatures lower than about 32 °F (0 °C) for a long period of time etc.
●The gasoline engine is warming up. ●The hybrid battery (traction battery) is low.
When the amount of remaining hybrid battery (traction battery) charge displayed on the meter is low. (→P. 195)
●Vehicle speed is high. ●The accelerator pedal is depressed firmly or the vehicle is on a hill etc. ●The windshield defogger is in use. *: Depending on the circumstances, EV drive mode may also not be
switched to in situations other than those above.
■Switching to EV drive mode when the gasoline engine is cold
If the hybrid system is started while the gasoline engine is cold, the gasoline engine will start automatically after a short period of time in order to warm up. In this case, you will become unable to switch to EV drive mode. After the hybrid system has started and the “READY” indicator has illumi- nated, press the EV drive mode switch before the gasoline engine starts to switch to EV drive mode.
181
PRIUS v_U (OM47674U)
2-1. Driving procedures
■Automatic cancellation of EV drive mode
When driving in EV drive mode, the gasoline engine may automatically restart in the following situations. When EV drive mode is canceled, a buzzer will sound and the EV drive mode indicator will flash and go off. ●The hybrid battery (traction battery) becomes low. ●Vehicle speed becomes high. ●The accelerator pedal is depressed firmly or the vehicle is on a hill etc.
■Possible driving distance when driving in EV drive mode
In EV drive mode, it is possible to drive up to about 1/2 mile (1 km) if driving at a speed of about 25 mph (40 km/h) or less. (The distance that is possible depends on the hybrid battery [traction battery] level and driving conditions.)
■Changing a driving mode when in EV drive mode
EV drive mode can be used in conjunction with Eco drive mode and power mode. However, EV drive mode may be automatically canceled when used in con- junction with power mode.
■Fuel economy
PRIUS v is designed to achieve the best possible fuel economy during nor- mal driving (using the gasoline engine and electric motor [traction motor]). Driving in EV drive mode more than necessary may lower fuel economy.
CAUTION
■While driving
When driving in EV drive mode, pay special attention to the area around the vehicle. Because there is no engine noise, pedestrians, people riding bicy- cles or other people and vehicles in the area may not be aware of the vehicle starting off or approaching them, so take extra care while driving.
182
PRIUS v_U (OM47674U)
2-1. Driving procedures Hybrid transmission
Select a shift position appropriate for the driving conditions. ■ Shifting the shift lever
Shift lever Operate the shift lever gently and ensure correct shifting operation.
When shifting to the D or R positions, move the shift lever along the shift gate. To shift to the N position, slide the shift lever to the left and hold it. The shift position will change to N. Shifting to B is only possible when shift position D is selected.
The shift lever will always return to this original position after a shifting operation.
When shifting from P to N, D or R, from D to R, or from R to D, ensure that the brake pedal is being depressed and the vehicle is stationary.
183
PRIUS v_U (OM47674U)
2-1. Driving procedures
Shift position indicator The position of the frame on the shift position indicator changes in accordance with the current shift position. When any shift position other than D or B is selected, the arrow toward B disappears from the shift position indicator.
When selecting the shift position, make sure that the shift position has been changed to the desired position by checking the shift position indica- tor provided on the instrument cluster. ■ Shift position purpose
Shift position
Function
Parking the vehicle/starting the hybrid system
Reversing Neutral
Normal driving*
Applying moderate engine braking when driving
down hills or on steep slopes
*: For good fuel economy and noise reduction, the D position should usu-
ally be used.
184
PRIUS v_U (OM47674U)
2-1. Driving procedures
■ Selecting a driving mode
The following modes can be selected to suit driving conditions:
Eco drive mode The torque generated in response to accelerator pedal depression will lessen compared to normal, and air conditioning operation (heating/ cooling) will be restrained, thus suiting driving with improved fuel effi- ciency. When the “ECO MODE” switch is pressed, the “ECO MODE” indicator comes on. Power mode Use when high levels of response and feeling are desirable, such as when driving in mountainous regions or when overtaking. When the power mode switch is pressed, the “PWR MODE” indicator comes on.
185
PRIUS v_U (OM47674U)
2-1. Driving procedures
P position switch
■ When shifting the shift position to P
Fully stop the vehicle and set the parking brake, and then press the P position switch.
the shift position
When is changed to P, the indicator comes on. Check that the P position is illumi- nated on the shift position indica- tor.
■ Shifting the shift position from P to other positions
● While depressing the brake pedal firmly, operate the shift lever. If the shift lever is operated without depressing the brake pedal, the buzzer will sound and the shifting operation will be disabled. ● When selecting the shift position, make sure that the shift posi- tion has been changed to the desired position by checking the shift position indicator provided on the instrument cluster. ● The shift position cannot be changed from P to B directly.
186
PRIUS v_U (OM47674U)
2-1. Driving procedures
■Operation of the air conditioning system in Eco drive mode
Eco drive mode controls the heating/cooling operations and fan speed of the air conditioning system to enhance fuel efficiency. (→P. 185) To improve air conditioning performance, adjust the fan speed or turn off Eco drive mode.
■For the shift positions
●When the “POWER” switch is off, the shift position cannot be changed. ●When the “POWER” switch is in ON mode (the hybrid system is not oper- ating), the shift position can only be changed to N. The shift position will be changed to N even if the shift lever is shifted to D or R and held in that position.
●When the “READY” indicator is on, the shift position can be changed
from P to D, N or R.
●When the “READY” indicator is flashing, the shift position cannot be
changed from P to another position even if the shift lever is operated.
●The shift position can only be changed to B directly from D. In addition, if an attempt is made to change the shift position by moving the shift lever in any of the following situations, the buzzer will sound and the shifting operation will be disabled or the shift position will automatically change to N. When this happens, select an appropriate shift position. ●Situations where the shifting operation will be disabled:
• When an attempt is made to change the shift position from P to another
position by moving the shift lever without depressing the brake pedal.
• When an attempt is made to change the shift position from P or N to B
by moving the shift lever.
187
PRIUS v_U (OM47674U)
2-1. Driving procedures
●Situations where the shift position will automatically change to N:
• When the P position switch is pressed while the vehicle is running.*1
• When an attempt is made to select the R position by moving the shift
lever when the vehicle is moving forward.*2
• When an attempt is made to select the D position by moving the shift
lever when the vehicle is moving in reverse.*3
• When an attempt is made to change the shift position from R to B by
*1: Shift position may be changed to P when driving at extremely low
moving the shift lever.
speeds.
*2: Shift position may be changed to R when driving at low speeds. *3: Shift position may be changed to D when driving at low speeds. ■Reverse warning buzzer
When shifting into R, a buzzer will sound to inform the driver that the shift position is in R.
■When the accelerator pedal is depressed while the shift position is in N
A buzzer will sound to inform the driver that the shift position is in N.
■Automatically P position selection function
When the shift position is in a position other than P, pressing the “POWER” switch with the vehicle stopped completely will cause the shift position to change to P automatically, and then the “POWER” switch will turn off.
■If the shift position cannot be shifted from P
There is a possibility that the 12-volt battery is discharged. Check the 12-volt battery in this situation. (→P. 479)
188
PRIUS v_U (OM47674U)
2-1. Driving procedures
■About engine braking
When shift position B is selected, releasing the accelerator pedal will apply engine braking. ●When the vehicle is driven at high speeds, compared to ordinary gaso- line-fueled vehicles, the engine braking deceleration is felt less than that of other vehicles.
●The vehicle can be accelerated even when shift position B is selected. If the vehicle is driven continuously in the B position, fuel efficiency will become low. Usually, shift the shift position to D. ■When canceling Eco drive mode/power mode
●Press the switch again. Also, power mode will be canceled automatically when the “POWER” switch is turned off. However, Eco drive mode will not be canceled automatically until the switch is pressed, even if the “POWER” switch is turned off.
●When in Eco drive mode, if the power mode switch is pressed or the operation is reversed, the mode will switch to that of the last switch to be pressed.
■Switching the drive mode when in EV drive mode
→P. 182
■After recharging/reconnecting the 12-volt battery
→P. 384
■Customization
Settings (e.g. Reverse warning buzzer) can be changed. (Customizable features →P. 523)
189
PRIUS v_U (OM47674U)
2-1. Driving procedures
CAUTION
■When driving on slippery road surfaces
Do not accelerate or shift the shift position suddenly. Sudden changes in engine braking may cause the vehicle to spin or skid, resulting in an accident.
■For the shift lever
Do not remove the shift lever knob or use anything but a genuine Toyota shift lever knob. Also, do not hang anything on the shift lever. Doing so could prevent the shift lever from returning to position, causing unexpected accidents to occur when the vehicle is in motion.
■P position switch
Do not press the P position switch while the vehicle is moving. If the P position switch is pressed when driving at very low speeds (for example, directly before stopping the vehicle), the vehicle may stop sud- denly when the shift position switches to P, which could lead to an accident.
190
PRIUS v_U (OM47674U)
2
2-1. Driving procedures
NOTICE
■Hybrid battery (traction battery) charge
If the shift position is in N, the hybrid battery (traction battery) will not be charged. To help prevent the battery from discharging, avoid leaving the N position selected for an extended period of time.
■Situations where P position control system malfunctions are possible If any of the following situations occurs, P position control system malfunc- tions are possible. Immediately stop the vehicle in a safe place on level ground, apply the park- ing brake, and then contact your Toyota dealer. ●When the “P LOCK MALFUNCTION WHEN PARKING, PARK IN FLAT PLACE AND APPLY PARKING BRAKE SECURELY” warning message appears on the instrument cluster. (→P. 446)
●When the parking lock system warning light is illuminated. ●When everything except the shift position indicator selection frame is illu-
minated.
●When the shift position indicator remains off.
■Notes regarding shift lever and P position switch operation
Avoid repeatedly operating the shift lever and P position switch in quick suc- cession. The system protection function may activate and it will not be temporarily possible to shift the shift position other than P. If this happens, please wait for a while before attempting to change the shift position again.
191
PRIUS v_U (OM47674U)
2-1. Driving procedures Turn signal lever
The turn signal lever can be used to show the following intention of the driver:
Right turn Left turn Lane change to the right (push and hold the lever partway) The right hand signals will flash until you release the lever. Lane change left (push and hold the lever partway) The left hand signals will flash until you release the lever.
the
to
■Turn signals can be operated when The “POWER” switch is in ON mode.
■If the indicator flashes faster than usual
Check that a light bulb in the front or rear turn signal lights has not burned out.
192
PRIUS v_U (OM47674U)
2-1. Driving procedures Parking brake
U.S.A.
Canada
To set the parking brake, fully depress the parking brake pedal with your left foot while depressing the brake pedal with your right foot. (Depressing the pedal again releases the parking brake.)
■Parking brake engaged warning buzzer
→P. 442
■Usage in winter time
See “Winter driving tips” for parking brake usage in winter time. (→P. 271)
NOTICE
■Before driving
Fully release the parking brake. Driving the vehicle with the parking brake set will lead to brake components overheating, which may affect braking performance and increase brake wear.
193
PRIUS v_U (OM47674U)
2-1. Driving procedures Horn
To sound the horn, press on or close to the
mark.
■After adjusting the steering wheel
Make sure that the steering wheel is securely locked. The horn may not sound if the steering wheel is not securely locked. (→P. 104)
194
PRIUS v_U (OM47674U)
2-2. Instrument cluster Gauges and meters
The units used on the trip information display etc. may differ depending on the target region. The following gauges and meters and display illuminate when the “POWER” switch is in ON mode:
Hybrid System Indicator Hybrid System Indicator represents the hybrid system power output and regenerative charging. Speedometer Displays the vehicle speed. Shift position indicators Displays the shift position. Fuel gauge Displays the quantity of fuel remaining in the tank. Hybrid battery (traction battery) status The amount of charge remaining in the hybrid battery (traction battery) is shown by 8 bars.
197
PRIUS v_U (OM47784U)
2-2. Instrument cluster
Trip information display Displays fuel consumption, driving range, etc. Odometer and trip meter display Odometer: Displays the total distance that the vehicle has been
driven.
Trip meter: Displays the distance the vehicle has been driven since the meter was last reset. Trip meters “A” and “B” can be used to record and display different dis- tances independently.
Clock
→P. 316
198
PRIUS v_U (OM47784U)
2-2. Instrument cluster
MPH or km/h button
The speed units can be selected MPH or km/h.
Press the button to switch the display between MPH and km/h.
Instrument panel light control
The brightness of the instrument panel lights can be adjusted by turn- ing the dial.
Brighter Darker When is turned to ON, the brightness will be reduced slightly unless the control dial is turned fully up.
the headlight switch
199
PRIUS v_U (OM47784U)
2-2. Instrument cluster
Changing the display
Switches between odometer and trip meter displays. When the trip meter is displayed, pressing and holding the “TRIP” button will reset the trip meter.
Switching the trip information display
Items displayed can be switched by pressing the “DISP” button.
200
PRIUS v_U (OM47784U)
2
2-2. Instrument cluster
Trip information display
■ Current fuel consumption
Displays the instant fuel consumption.
■ Average fuel consumption
The average fuel consumption is displayed on both the odometer and the trip meter. • While the odometer is being displayed, or when the odometer/trip meter are not being displayed, the average fuel consumption from the last reset will be displayed.
• While the trip meter is being displayed, the average fuel consumption will be displayed in accordance with the trip meter distance from the last reset.
• The function can be reset by pressing the “DISP” button for longer than 1 second when the average fuel consumption is displayed.
• Use the displayed average fuel consumption
as a reference.
201
PRIUS v_U (OM47784U)
2-2. Instrument cluster
■ Cruising range
■ “SET” screen
Displays the estimated maximum distance that can be driven with the quantity of fuel remain- ing. • This distance is computed based on your
average fuel consumption. As a result, the actual distance that can be driven may differ from that displayed.
• When only a small amount of fuel is added to
the tank, the display may not be updated. When refueling, turn the “POWER” switch off. If the vehicle is refueled without turning the “POWER” switch off, the display may not be updated.
The items displayed on Hybrid System Indica- tor can be setup. (→P. 205)
202
PRIUS v_U (OM47784U)
2
2-2. Instrument cluster
Hybrid System Indicator
Hybrid System Indicator displays the hybrid system operating condi- tion and provides Eco-friendly driving assistance in accordance with the driving conditions and the acceleration. ■ Names and meaning of each icons
Eco Driving Indicator Light Turns on when the vehicle is driven in Eco-friendly. Hybrid System Indicator Refer to “Reading Hybrid System Indicator” below. EV indicator The EV indicator comes on when driving the vehicle using only the electric motor (traction motor).
■ Reading Hybrid System Indicator
As shown below, the driving conditions of the vehicle can be con- firmed by checking the status of the indicator.
Charge area Eco area Hybrid Eco area Power area
203
PRIUS v_U (OM47784U)
2-2. Instrument cluster
As shown below, the driving conditions of the vehicle can be con- firmed by checking the status of the indicator.
Hybrid System Indicator status
Display*1
Charge area: Shows regenerative charging.*2 (→P. 31)
Eco area: Shows that the vehicle is driven in Eco-friendly.
Hybrid Eco area:
Shows that gasoline engine power is not being
used very often.*3
Power area: Shows that the driving power is more than the upper limit of Eco driving (during full power driv- ing etc.). *1: The images are examples only, and may vary slightly from actual condi-
tions.
*2: The displayed status is intended as a guide, and may differ from the
actual status.
*3: The gasoline engine will automatically stop and restart under various
conditions.
204
PRIUS v_U (OM47784U)
2
2-2. Instrument cluster
Changing Hybrid System Indicator settings
The items displayed on Hybrid System Indicator can be changed by operating the “DISP” button. Stop the vehicle in a place in which the operation can be safely carried out, apply the parking brake, and shift the shift position to P.
After pressing the “DISP” button
to display the “SET” screen on
the trip information display, press
and hold the “DISP” button for 1
second or more.
The “SET” display and Hybrid System Indicator will flash.
Press the “DISP” button while the display is flashing to select the items to be displayed. The display items will flash.
Display all Display Hybrid System Indica- tor and EV indicator Display Hybrid System Indica- tor only Display none Display Eco Driving Indicator Light only
205
STEP 1
STEP 2
PRIUS v_U (OM47784U)
2-2. Instrument cluster
STEP 3
Press and hold the “DISP” button for 1 second or more to complete the setup. If setup is not completed by pressing and holding the “DISP” button for 1 second or more, or if nothing is operated within approximately 10 seconds, the screen will return and the settings will be lost.
■Eco Driving Indicator Light
Eco Driving Indicator Light will turn on when driving power is lower than the upper limit of Eco driving. It will turn off when the acceleration exceeds the Eco driving accelerator upper limit or when the vehicle is stopped. Eco Driving Indicator Light will not operate in the following conditions: ●The shift position is anything other than D. ●The driving mode is set to power mode or EV drive mode. (→P. 187) ●The vehicle speed is approximately 80 mph (130 km/h) or higher. Eco Driving Indicator Light can be set to activated or deactivated. (→P. 205)
■Remaining hybrid battery (traction battery) charge display
The charge amount of the hybrid battery (traction battery) is automatically controlled by the hybrid system. For this reason, even if electricity is recov- ered via the regenerative braking, or electricity is generated via the gasoline engine, the displayed hybrid battery (traction battery) charge amount may not reach the highest level (level 8). However, this does not indicate a mal- function.
206
PRIUS v_U (OM47784U)
2-2. Instrument cluster
■Engine speed
On hybrid vehicles, engine speed is precisely controlled in order to help improve fuel efficiency and reduce exhaust emissions etc. There are times when the engine speed that is displayed may differ even when vehicle operation and driving conditions are the same.
■Brightness of the instrument panel light
If the headlight switch is turned to ON while the surrounding area is dark, the instrument panel lights will dim.
■When disconnecting and reconnecting 12-volt battery terminals
The average fuel consumption and cruising range will be reset.
NOTICE
■To prevent damage to the engine and its components
The engine may be overheating if the high coolant temperature warning light comes on or flashes. In this case, immediately stop the vehicle in a safe place, and check the engine after it has cooled completely. (→P. 487)
■The trip information display at low temperatures
Allow the interior of the vehicle to warm up before using the liquid crystal information display. At extremely low temperatures, the information display monitor may respond slowly, and display changes may be delayed.
207
PRIUS v_U (OM47784U)
2-2. Instrument cluster Indicators and warning lights
The indicator and warning lights on the instrument cluster inform the driver of the status of the vehicle’s various systems. Instrument cluster
Some indicators and the units used on the trip information display etc. may differ depending on the target region. Center panel
208
PRIUS v_U (OM47784U)
2-2. Instrument cluster
■ Indicators
The indicators inform the driver of the operating state of the vehicle’s various systems.
*1
Eco Driving Indicator Light (→P. 203)
“ECO MODE” indicator (→P. 187)
Power mode indicator (→P. 187)
Cruise control indicator (→P. 231, 235)
Radar cruise control indicator (→P. 235)
(if equipped) (green)
(if equipped) (green)
“SET” indicator (→P. 231, 235)
Slip indicator (→P. 253, 256)
*1, 2
209
(U.S.A.)
(Canada)
Turn signal indicator (→P. 194)
Headlight indicator (→P. 213)
Tail light indicator (→P. 213)
Headlight high beam indicator (→P. 218)
Front fog light indicator (→P. 221)
Security indicator (→P. 119)
“READY” indicator (→P. 175)
PRIUS v_U (OM47784U)
2-2. Instrument cluster
EV indicator (→P. 203)
EV drive mode indica- tor (→P. 182)
Shift position indicators (→P. 185)
*1, 3
(if equipped)
“PCS” warning (→P. 259)
SRS airbag on-off indicator (→P. 138)
*1: These lights turn on when the “POWER” switch is turned to the ON mode to indicate that a system check is being performed. They will turn off after the hybrid system is on, or after a few seconds. There may be a malfunction in a system if a light does not come on, or if the lights do not turn off. Have the vehicle inspected by your Toyota dealer.
*2: The light flashes to indicate that the system is operating. *3: The light comes on when the system is turned off. The light flashes
faster than usual to indicate that the system is operating.
210
PRIUS v_U (OM47784U)
2-2. Instrument cluster
■ Warning lights
Warning lights inform the driver of malfunctions in any of the vehicle’s systems. (→P. 444)
*1
*1
*1
*1
*1
*1
(Canada)
(U.S.A.)
*1
*1
*1
*1
*1
*1
*1
(U.S.A.)
*1
(Canada)
(red)
*1
(yellow)
*1
(if equipped) (if equipped)
*1, 2
*1
*1
*1
*1
(if equipped)
(if equipped)
(yellow)
(if equipped)
(yellow)
(U.S.A.)
(Canada)
*1
(U.S.A.)
(U.S.A.)
(Canada)
*1: These lights turn on when the “POWER” switch is turned to ON mode to indicate that a system check is being performed. They will turn off after the hybrid system is on, or after a few seconds. There may be a malfunction in a system if a light does not come on, or if the lights do not turn off. Have the vehicle inspected by your Toyota dealer.
*2: The light flashes to indicate a malfunction.
211
PRIUS v_U (OM47784U)
2-2. Instrument cluster
CAUTION
■If a safety system warning light does not come on
Should a safety system light such as the ABS and SRS airbag warning light not come on when you start the hybrid system, this could mean that these systems are not available to help protect you in an accident, which could result in death or serious injury. Have the vehicle inspected by your Toyota dealer immediately if this occurs.
212
PRIUS v_U (OM47784U)
2
2-3. Operating the lights and windshield wipers Headlight switch
The headlights can be operated manually or automatically. Turning the end of the lever turns on the lights as follows: U.S.A. (type A)
The daytime running lights turn on. The side marker, parking, tail, license plate, daytime run- ning lights and instru- ment panel lights turn on. The headlights and all the lights listed above (except day- time running lights) turn on. The headlights, park- ing lights, daytime running lights and so on turn on and off automatically (when the “POWER” switch is in ON mode).
(if equipped)
213
PRIUS v_U (OM47784U)
2-3. Operating the lights and windshield wipers
U.S.A. (type B)
(if equipped)
The headlights, park- ing lights, daytime running lights and so on turn on and off automatically (when the “POWER” switch is in ON mode). The side marker, parking, tail, license plate, daytime run- ning lights and instru- ment panel lights turn on. The headlights and all the lights listed above (except day- time running lights) turn on. The daytime running lights turn off.
214
PRIUS v_U (OM47784U)
2
2-3. Operating the lights and windshield wipers
U.S.A. (type C)
The daytime running lights turn on. The side marker, parking, tail, license plate, daytime run- ning lights and instru- ment panel lights turn on. The headlights and all the lights listed above (except day- time running lights) turn on. The headlights, park- ing lights, daytime running lights and so on turn on and off automatically (when the “POWER” switch is in ON mode).
(if equipped)
215
PRIUS v_U (OM47784U)
2-3. Operating the lights and windshield wipers
U.S.A. (type D)
(if equipped)
The headlights, park- ing lights, daytime running lights and so on turn on and off automatically (when the “POWER” switch is in ON mode). The side marker, parking, tail, license plate, daytime run- ning lights and instru- ment panel lights turn on. The headlights and all the lights listed above (except day- time running lights) turn on. The daytime running lights turn off.
216
PRIUS v_U (OM47784U)
2
2-3. Operating the lights and windshield wipers
Canada
The daytime running lights turn on. The side marker, parking, tail, license plate, daytime run- ning lights and instru- ment panel lights turn on. The headlights and all the lights listed above (except day- time running lights) turn on. The headlights, park- ing lights, daytime running lights and so on turn on and off automatically (when the “POWER” switch is in ON mode).
(if equipped)
217
PRIUS v_U (OM47784U)
2-3. Operating the lights and windshield wipers
Turning on the high beam headlights
With the headlights on, push the lever away from you to turn on the high beams. Pull the lever toward you to the center position to turn the high beams off. Pull the lever toward you and release it to flash the high beams once. You can flash the high beams with the headlights on or off.
■Daytime running light system
●To make your vehicle more visible to other drivers, the daytime running lights turn on automatically (at a reduced intensity) whenever the hybrid system is started and the parking brake is released. Daytime running lights are not designed for use at night. For the U.S.A.: Daytime running lights can be turned off by operating the switch.
●Compared to turning on the headlights, the daytime running light system offers greater durability and consumes less electricity, so it can help improve fuel economy.
218
PRIUS v_U (OM47784U)
2-3. Operating the lights and windshield wipers
■Headlight control sensor (if equipped)
The sensor may not function properly if an object is placed on the sensor, or any- thing that blocks the sensor is affixed to the windshield. Doing so the sensor detecting the level of ambient light and may cause the automatic headlight sys- tem to malfunction. Air conditioning operation may also be interrupted.
interferes with
■Automatic light off system
●When the headlights come on: The headlights and tail lights turn off 30
seconds after a door is opened and closed if the “POWER” switch is
turned to ACCESSORY mode or turned off. (The lights turn off immedi-
ately if
on the key is pressed after all the doors are locked.)
●When only the tail lights come on: The tail lights turn off automatically if the “POWER” switch is turned to ACCESSORY mode or turned off and the driver’s door is opened.
To turn the lights on again, turn the “POWER” switch to ON mode, or turn the light switch off once and then back to
or
219
PRIUS v_U (OM47784U)
2-3. Operating the lights and windshield wipers
■Automatic headlight leveling system (if equipped)
The level of the headlights is automatically adjusted according to the number of passengers and the loading condition of the vehicle to ensure that the headlights do not interfere with other road users.
■Customization
Settings (e.g. light sensor sensitivity) can be changed. (Customizable features →P. 525)
NOTICE
■To prevent 12-volt battery discharge
Do not leave the lights on longer than necessary when the hybrid system is off.
220
PRIUS v_U (OM47784U)
2-3. Operating the lights and windshield wipers Fog light switch∗
The fog lights secure excellent visibility in difficult driving condi- tions, such as in rain and fog. Type A
Turns the fog lights off Turns the fog lights on
∗: If equipped
221
PRIUS v_U (OM47784U)
2-3. Operating the lights and windshield wipers
Type B
Turns the fog lights off Turns the fog lights on
■Fog lights can be used when
The headlights are on in low beam.
NOTICE
■To prevent 12-volt battery discharge
Do not leave the lights on longer than necessary when the hybrid system is off.
222
PRIUS v_U (OM47784U)
2
2-3. Operating the lights and windshield wipers Windshield wipers and washer
When intermittent windshield wiper operation is selected, wiper intervals can be also adjusted. The wiper operation is selected by moving the lever as follows. Type A
wind- Intermittent shield wiper opera- tion Low speed wind- shield wiper opera- tion High speed wind- shield wiper opera- tion Temporary operation
223
PRIUS v_U (OM47784U)
2-3. Operating the lights and windshield wipers
the
Increases intermittent windshield wiper frequency Decreases the intermittent windshield wiper frequency
Washer/wiper dual opera- tion The wipers will automatically operate a couple of times after the washer squirts. If the headlights are on, the headlight cleaner will operate once.
224
PRIUS v_U (OM47784U)
2
2-3. Operating the lights and windshield wipers
Type B
Intermittent wind- shield wiper opera- tion Low speed wind- shield wiper opera- tion High speed wind- shield wiper opera- tion Temporary operation
225
PRIUS v_U (OM47784U)
2-3. Operating the lights and windshield wipers
the
Increases intermittent windshield wiper frequency Decreases the intermittent windshield wiper frequency
Washer/wiper dual opera- tion The wipers will automatically operate a couple of times after the washer squirts. If the headlights are on, the headlight cleaner will operate once.
■The windshield wipers and washer can be operated when
The “POWER” switch is in ON mode.
■If no windshield washer fluid sprays
Check that the washer nozzles are not blocked if there is washer fluid in the washer fluid tank.
226
PRIUS v_U (OM47784U)
2
2-3. Operating the lights and windshield wipers
NOTICE
■When the windshield is dry
Do not use the wipers, as they may damage the windshield.
■When the washer fluid tank is empty
Do not operate the switch continually as the washer fluid pump may over- heat.
■When a nozzle becomes blocked
In this case, contact your Toyota dealer. Do not try to clear it with a pin or other object. The nozzle will be damaged.
■To prevent 12-volt battery discharge
Do not leave the wipers on longer than necessary when the hybrid system is off.
227
PRIUS v_U (OM47784U)
2-3. Operating the lights and windshield wipers Rear window wiper and washer
Turning the end of the lever turns on the rear window wiper and washer as follows: Type A
Intermittent window wiper operation Normal window wiper operation Washer/wiper operation Washer/wiper operation
dual
dual
228
PRIUS v_U (OM47784U)
2-3. Operating the lights and windshield wipers
Type B
Intermittent window wiper operation Normal window wiper operation Washer/wiper operation Washer/wiper operation
dual
dual
■The rear window wiper and washer can be operated when
The “POWER” switch is in ON mode.
■If no washer fluid sprays
Check that the washer nozzles are not blocked if there is washer fluid in the washer fluid reservoir.
NOTICE
■When the rear window is dry
Do not use the wiper, as it may damage the rear window.
■When the washer fluid tank is empty
Do not operate the switch continually as the washer fluid pump may over- heat.
229
PRIUS v_U (OM47784U)
2-3. Operating the lights and windshield wipers Headlight cleaner switch∗
Washer fluid can be sprayed on the headlights.
Press the switch to clean the headlights.
■The headlight cleaners can be operated when
The “POWER” switch is in ON mode and the headlight switch is turned on.
■Windshield washer linked operation
Only for the first time when the windshield washer is operated with the “POWER” switch in ON mode and the headlights on, the headlight cleaners will operate once. (→P. 223)
NOTICE
■When the washer fluid tank is empty
Do not press the switch continually as the washer fluid pump may overheat.
∗: If equipped
230
PRIUS v_U (OM47784U)
2-4. Using other driving systems Cruise control∗
Use the cruise control to maintain a set speed without depressing the accelerator pedal.
Indicators Cruise control switch
■ Setting the vehicle speed
STEP 1
Press the “ON-OFF” button to activate the cruise control.
indicator will
Cruise control come on. Press deactivate the cruise control.
the button again
to
Accelerate or decelerate to the desired speed, and push the lever down to set the speed.
“SET” indicator will come on. The vehicle speed at the moment the lever is released becomes the set speed.
∗: If equipped
229
STEP 2
PRIUS v_U (OM47674U)
2-4. Using other driving systems
■ Adjusting the set speed
To change the set speed, operate the lever until the desired set speed is obtained.
Increases the speed Decreases the speed Fine adjustment: Momentarily move the lever in the desired direction. Large adjustment: Hold lever in the desired direction.
the
The set speed will be increased or decreased as follows: Fine adjustment: By approximately 1 mph (1.6 km/h) each time