Login- Download PDF Manual
-
the movement of
if
This places the latch in the locked posi- tion.
3. Move the release handle, from outside the vehicle, in the direction of the arrow to check if the latch is released.
Black plate (107,1)
Keys and doors 2-23
Rear gate (Wagon)
The rear gate can be locked and unlocked using either the keyless entry system or the power door locking switches. Refer to the “Power door locking switches” and “Remote keyless entry system” sec- tion in this chapter.
To open the rear gate, first unlock the rear gate lock then pull the outside handle up. Then, hold the rear gate and raise it as high as it will go.
– CONTINUED –
北米Model "A1920BE-B" EDITED: 2006/ 9/ 19
Black plate (108,1)
2-24 Keys and doors
CAUTION
Moonroof (if equipped)
To close the rear gate, lower it slowly and push down firmly until the latch engages. The rear gate can be lowered easily if you pull it down holding the recessed grip.
WARNING
. To prevent dangerous exhaust gas from entering the vehicle, always keep the rear gate closed while driving.
. Do not attempt to shut the rear gate while holding the recessed grip. Also avoid closing the rear gate by pulling on the recessed grip from inside the cargo space. There is a danger of your hand being caught and injured.
. Do not jam a plastic bag in or place cellophane tape on the rear gate stays or scratch the stays while loading or unloading cargo. That could cause leakage of gas from the stays, which may result in their inability to hold the rear gate open.
. Be careful not to hit your head or face on the rear gate when open- ing or closing the rear gate and when loading or unloading car- go.
NOTE If the rear gate cannot be unlocked due to a discharged battery, a fault in the door locking/unlocking system or other causes, you can unlock it by manually operating the rear gate lock release lever. For the procedure, refer to “Rear gate – if the rear gate cannot be unlocked” section in chapter 9 “In case of emer- gency”.
The moonroof has both tilting and sliding functions.
The moonroof operates only when the ignition switch is in the “ON” position.
& Tilt function
1) 2)
Tilt up Tilt down
The tilting function will only operate when the moonroof is fully closed. Push the rear side of the “Tilt” switch to raise the moonroof. Push the front side of the “Tilt” switch to lower the moonroof.
Release the switch after the moonroof has
北米Model "A1920BE-B" EDITED: 2006/ 9/ 19
been raised or has been lowered com- pletely. Pushing the switch continuously may cause damage to the moonroof.
& Sliding function
1) Open 2) Close
Push the “Open/Close” switch rearward to open the moonroof. The sun shade will also be opened together with the moon- roof. Push the “Open/Close” switch forward to close the moonroof. The moonroof will stop halfway if you continue to press on the switch. Release the switch once and push it again to close the moonroof completely.
After washing the vehicle or after it rains,
to wipe away water on the roof prior opening the moonroof to prevent drops of water from falling into the passenger compartment. NOTE If the moonroof cannot be closed through switch operation because of system failure, it can be closed manu- ally using a hex-head wrench. For the procedure, refer to “Moonroof – if the moonroof cannot be closed” section in chapter 9 “In case of emergency”.
WARNING
. Never let anyone’s hands, arms, head or any objects protrude from the moonroof. A person could be seriously injured if the vehicle stops suddenly or turns sharply or if the vehicle is in- volved in an accident. To avoid serious personal injury caused by entrapment, you must do the following.
. Before closing the moonroof, make sure that no one’s hands, arms, head or other objects will be accidentally caught in the moonroof.
. Before leaving the vehicle, al-
Black plate (109,1)
Keys and doors 2-25
ways remove the key from the ignition switch for safety and never allow an unattended child to remain in the vehicle. Failure to follow this procedure could result in injury to a child operat- ing the moonroof.
CAUTION
. Do not sit on the edge of the open
moonroof.
. Do not operate the moonroof if falling snow or extremely cold conditions have caused it to freeze shut.
– CONTINUED –
北米Model "A1920BE-B" EDITED: 2006/ 9/ 19
2-26 Keys and doors
& Sun shade
The sun shade can be slid forward or backward by hand while the moonroof is closed. If the moonroof is opened, the sun shade also moves back.
Black plate (110,1)
北米Model "A1920BE-B" EDITED: 2006/ 9/ 19
Ignition switch ..................................................... LOCK.................................................................. Acc..................................................................... ON...................................................................... START ................................................................ Key reminder chime ............................................ Ignition switch light ............................................. Key interlock release (AT vehicles only) ............... Hazard warning flasher....................................... Meters and gauges (WRX-STI) ........................... Combination meter illumination ........................... Canceling sequential illumination of the
3-3
3-3
3-4
3-4
3-4
3-5
3-5
3-5
3-6
3-6
3-6combination meter ............................................ Speedometer....................................................... Odometer/Trip meter............................................ Tachometer ......................................................... Fuel gauge.......................................................... Temperature gauge ............................................. Outside temperature indicator ............................. REV indicator light and buzzer (WRX-STI) ........
3-6
3-7
3-7
3-7
3-8
3-8
3-9
3-9
Setting the alarm-level engine speed................... 3-10
Deactivating the REV alarm system..................... 3-11
Meters and gauges (Except WRX-STI).............. 3-11
3-11
Speedometer...................................................... Odometer/Trip meter........................................... 3-11
Tachometer ........................................................ 3-12
Fuel gauge......................................................... 3-12
Temperature gauge ............................................ 3-13
Outside temperature indicator ............................ 3-13
Warning and indicator lights ............................. 3-14
Seatbelt warning light and chime ........................ 3-14Black plate (5,1)
Instruments and controls
SRS airbag system warning light........................ Front passenger’s frontal airbag ON and OFF indicators ........................................................
CHECK ENGINE warning light/Malfunction
indicator lamp ................................................. Charge warning light.......................................... Oil pressure warning light .................................. AT OIL TEMPerature warning light
(AT vehicles)....................................................
Rear differential oil temperature warning light
(WRX-STI)........................................................ ABS warning light.............................................. Brake system warning light................................ Door open warning light .................................... All-Wheel Drive warning light (AWD AT vehicles – if equipped) .....................................................
Intercooler water spray warning light
(WRX-STI)........................................................
Selector lever position indicator
(AT vehicles).................................................... Turn signal indicator lights................................. High beam indicator light ................................... Cruise control indicator light.............................. Cruise control set indicator light ........................ Driver’s control center differential auto indicator light (WRX-STI) ................................................ Driver’s control center differential indicator and warning lights (WRX-STI) ................................. Lights indicator light (WRX-STI) ......................... REV indicator light (WRX-STI) ............................ Clock ..................................................................
3-14
3-15
3-16
3-16
3-163-17
3-17
3-17
3-18
3-193-19
3-19
3-20
3-20
3-20
3-20
3-203-20
3-21
3-21
3-21
3-22北米Model "A1920BE-B" EDITED: 2006/ 9/ 19
Black plate (6,1)
Instruments and controls
Light control switch ........................................... 3-22
Headlights.......................................................... 3-22
High/low beam change (dimmer)......................... 3-23
Headlight flasher ................................................ 3-23
Daytime running light system ............................. 3-23
Turn signal lever ................................................ 3-24
Illumination brightness control ......................... 3-25
Headlight beam leveler (U.S.-spec.WRX-STI).......................................................... 3-25
Parking light switch ........................................... 3-25
Front fog light button (if equipped) .................. 3-26Wiper and washer.............................................. Windshield wiper and washer switches .............. Rear window wiper and washer switch – Wagon............................................................. Rear window defogger button .......................... Windshield wiper deicer (if equipped).............. Intercooler water spray switch (WRX-STI) ....... Mirrors ................................................................ Inside mirror...................................................... Outside mirrors ................................................. Tilt steering wheel ............................................. Horn....................................................................
3-26
3-273-28
3-29
3-30
3-31
3-32
3-32
3-33
3-35
3-35北米Model "A1920BE-B" EDITED: 2006/ 9/ 19
Ignition switch
WARNING
. Never turn the ignition switch to “LOCK” while the vehicle is being driven or towed because that will lock the steering wheel, preventing steering control. And when the engine is turned off, it takes a much greater effort than usual to steer.
. Before leaving the vehicle, al- ways remove the key from the ignition switch for safety and never allow an unattended child to remain in the vehicle. Failure to follow this procedure could result in injury to a child or others. Children could operate the power windows, the moon- roof or other controls or even make the vehicle move.
CAUTION
Do not attach a large key holder or key case to either key. If it banged against your knees or hands while you are driving, it could turn the ignition switch from the “ON” posi-
if
tion to the “Acc” or “LOCK” posi- tion, thereby stopping the engine. Also, the key is attached to a keyholder or to a large bunch of other keys, centrifugal force may act on it as the vehicle moves, resulting in unwanted turning of the ignition switch.
The ignition switch has four positions: LOCK, Acc, ON and START. NOTE . Keep the ignition switch in the “LOCK” position when the engine is not running. . Using electrical accessories for a long time with the ignition switch in the "ON" or “Acc” position can cause the
Black plate (113,1)
Instruments and controls 3-3
battery to go dead. . If the ignition switch will not move from the “LOCK” position to the “Acc” position, turn the steering wheel slightly to the left and right as you turn the ignition switch.
& LOCK The key can only be inserted or removed in this position. The ignition switch will lock the steering wheel when you remove the key. If turn the steering wheel slightly to the right and left as you turn the key. ! Automatic transmission vehicles
turning the key is difficult,
– CONTINUED –
北米Model "A1920BE-B" EDITED: 2006/ 9/ 19
3-4 Instruments and controls
The key can be turned from “Acc” to “LOCK” only when the selector lever is in the “P” position. ! Manual transmission vehicles
The key can be turned from “Acc”
to
“LOCK” only when the key is pushed in while turning it.
& Acc In this position the electrical accessories (radio, accessory power outlet, etc.) can be used.
& ON This is the normal operating position after the engine is started.
& START The engine is started in this position. The starter cranks the engine to start it. When the key is released (after the engine has started), the key automatically returns to the “ON” position.
CAUTION
Do not turn the ignition switch to the “START” position while the engine is running.
! For vehicle with immobilizer If your registered key fails to start the engine, pull out the key once (the security indicator light will blink), and then insert the key in the ignition switch and turn it to the “START” position and again try to start
Black plate (114,1)
the engine. NOTE The engine may not start in the follow- ing cases:
. The key grip is touching another key or a metallic key holder.
北米Model "A1920BE-B" EDITED: 2006/ 9/ 19
& Ignition switch light For easy access to the ignition switch in the dark, the ignition switch light comes on when driver’s door is opened. The light remains on for 5 seconds and goes out after driver’s door is closed or if the key is turned to the “ON” position.
& Key interlock release (AT ve-
hicles only)
If the key can not be turned to the “LOCK” position even when the selector lever is in the “P” position: 1. Take out the screwdriver from the tool bag.
2. Remove the cover under the steering column using a Phillips screwdriver.
. The key is near another key that contains an immobilizer transponder.
. The key is near or touching another transmitter.
& Key reminder chime The reminder chime sounds when the driver’s door opens and the key is in the “LOCK” or “Acc” position. The chime stops when the key is removed from the ignition switch. NOTE The ignition switch light flashes when the reminder chime sounds.
Black plate (115,1)
Instruments and controls 3-5
3. Turn the ignition key while pressing the key interlock release lever.
Take your vehicle to the nearest SUBARU dealer immediately to have the key inter- lock system repaired.
北米Model "A1920BE-B" EDITED: 2006/ 9/ 19
3-6 Instruments and controls
Hazard warning flasher
The hazard warning flasher is used to warn other drivers when you have to park your vehicle under emergency conditions. The hazard warning flasher works with the ignition switch in any position.
To turn on the hazard warning flasher, push the hazard warning button on the instrument panel. To turn off the flasher, push the button again. NOTE When the hazard warning flasher is on, the turn signals do not work.
Meters and gauges (WRX- STI)
NOTE Liquid-crystal displays are used in some of the meters and gauges in the combination meter. You will find their indications hard to see if you wear polarized glasses.
& Combination meter illumina-
tion
the various parts of
When the ignition switch is turned to the “ON” position, the combination meter are illuminated in the following sequence: 1. Meter needles and gauge needles light up. 2. Meter needles and gauge needles each show MAX position. 3. Meter needles and gauge needles each show MIN position, and REV indi- cator flashes. 4. Dials and indicators in meters and gauges light up. 5. 6. Regular illumination (for driving) be- gins.
“STI” mark lights up.
Black plate (116,1)
& Canceling sequential illumi-
nation of the combination meter
With the ignition switch in the “ON” position, it is possible to cancel sequential illumination of the combination meter. Press the trip knob while turning the REV setting knob clockwise or counterclock- wise. The buzzer will sound briefly, and the outside temperature indicator will show “ON” or “– –”.
ON : sequential illumination – –: sequential illumination canceled The setting toggles between “ON” and “– –” each time the trip knob is pressed. Return the REV setting knob to its original position to complete the setting process. The buzzer will sound briefly. A few seconds later, the outside temperature indicator will return to showing the outside temperature. NOTE It is not possible to cancel sequential illumination of the combination meter while sequential illumination is actually taking place. Cancel sequential illumi- nation when regular illumination (for driving) has begun.
北米Model "A1920BE-B" EDITED: 2006/ 9/ 19
& Speedometer The speedometer shows the vehicle speed.
& Odometer/Trip meter
the odometer/trip meter will go off. ! Odometer The odometer shows the total distance that the vehicle has been driven. ! Double trip meter
1) Trip meter 2) Odometer
This meter displays the odometer and two trip meters when the ignition switch is in the “LOCK”, “Acc” or “ON” position.
If you press the trip knob when the ignition switch is in the “LOCK” position, the odometer/trip meter will light up. is possible to switch between the A trip meter and B trip meter indications while the odometer/trip meter is lit up. If you do not press the trip knob within 10 seconds of illumination of the odometer/trip meter,
It
The trip meter shows the distance that the vehicle has been driven since you last set it to zero. To change the mode indication, briefly push the knob. Each press of function alternately.
the knob changes the
To set the trip meter to zero, select the A trip or B trip meter by pushing the knob and keep the knob pushed for more than 2
Black plate (117,1)
Instruments and controls 3-7
seconds.
CAUTION
To ensure safety, do not attempt to change the function of the indicator during driving, as an accident could result.
NOTE If the connection between the combina- tion meter and battery is broken for any reason such as vehicle maintenance or fuse replacement, the data recorded on the trip meter will be lost.
& Tachometer The tachometer shows the engine speed in thousands of revolutions per minute.
CAUTION
Do not operate the engine with the pointer of the tachometer in the red zone. In this range, fuel injection will be cut by the engine control module to protect the engine from overrev- ving. The engine will resume run- ning normally after the engine speed is reduced below the red zone.
– CONTINUED –
北米Model "A1920BE-B" EDITED: 2006/ 9/ 19
3-8 Instruments and controls
& Fuel gauge
NOTE
1)
Low fuel warning light
The fuel gauge shows the approximate amount of fuel remaining in the tank. When the ignition switch is in the “LOCK” or “Acc” position, the fuel gauge shows “E” even if the fuel tank contains fuel.
The gauge may move slightly during braking, turning or acceleration due to fuel level movement in the tank.
” sign in the fuel
You will see the “ gauge meter. This indicates that the fuel filler door (lid) is located on the right side of the vehicle.
! Low fuel warning light The low fuel warning light comes on when the tank is nearly empty [Approximately 2.3 US gal (9.0 liters, 1.9 Imp gal)].
It only operates when the ignition switch is in the “ON” position. NOTE This light does not go out unless the tank is replenished up to an internal
Black plate (118,1)
fuel quantity of approximately 4.0 US gal (15 liters, 3.3 Imp gal).
CAUTION
Promptly put fuel in the tank when- ever the low fuel warning light comes on. Engine misfires as a result of an empty tank could cause damage to the engine.
& Temperature gauge
1) Normal operating range
The temperature gauge shows engine coolant temperature when the ignition switch is in the “ON” position.
The coolant
temperature will vary in
北米Model "A1920BE-B" EDITED: 2006/ 9/ 19
accordance with the outside temperature and driving conditions.
We recommend that you drive moderately until the pointer of the temperature gauge reaches near the middle of the range. Engine operation is optimum with the engine coolant at this temperature range and high revving operation when the engine is not warmed up enough should be avoided.
CAUTION
If the pointer exceeds the normal operating range, safely stop the vehicle as soon as possible. See the “In case of emergency” in chapter 9.
Black plate (119,1)
& Outside temperature indica-
tor
REV indicator light and buz- zer (WRX-STI)
Instruments and controls 3-9
1) U.S.-spec. models 2) Canada-spec. models
The outside temperature indicator shows the outside temperature in a range from −22 to 1228F (−30 to 508C). The indicator can give a false reading under any of the following conditions: . When there is too much sun. . During idling; while running at low speeds in a traffic jam; when the engine is restarted immediately following a shut- down. . When the actual outside temperature falls outside the specified indicator range.
light
The REV alarm system issues a warning using the REV indicator (and a buzzer if additionally selected) when the engine speed reaches a level previously set using the REV setting knob. If you press the trip knob when the ignition switch is in the “LOCK” position, the outside temperature indicator will show the engine speed that has already been set.
– CONTINUED –
北米Model "A1920BE-B" EDITED: 2006/ 9/ 19
3-10 Instruments and controls
NOTE Even if the REV alarm system is not set, the REV indicator light will come on whenever the engine speed enters the tachometer’s red zone.
& Setting the alarm-level en-
gine speed
. Counterclockwise (−): Speed setting changes downward by 100 rpm. . Clockwise (+): Speed setting changes upward by 100 rpm. The speed setting will stop changing if it the maximum engine speed.
reaches 0 rpm or
The alarm-level engine speed can be set (in 100 rpm steps) within the range from 2,000 rpm to 7,000 rpm. The indicator shows the setting as follows: Speed (rpm)
Indication
2,000
2,100
–
7,000
00
20
21
–70
1. Turn the REV setting knob clockwise or counterclockwise, then release it and let it return to its initial position. The buzzer will sound. The REV alarm system is now ready to be set. 2. Turn the REV setting knob to select the desired alarm-level engine speed. At the outside temperature indicator will show the engine-speed setting.
this time,
Approximately 3 seconds after you stop turning the knob, the REV alarm system will automatically enter its next setting mode (step 3 below), in which you can activate or deactivate the buzzer. 3. Activate or deactivate the buzzer as desired using the REV setting knob.
. Turn the knob clockwise (+) to activate the buzzer. The indicator will show “ON”, and the buzzer will sound
Black plate (120,1)
three times. With the buzzer activated, engine-speed warnings are given by both the REV indicator light and the buzzer. . Turn the knob counterclockwise (−) to deactivate the buzzer. The indicator will show “– –”, and the buzzer will not sound. With the buzzer deactivated, engine-speed warnings are given only by the REV indicator light.
Approximately 3 seconds after you stop turning the knob, the buzzer will sound the setting once to indicate the end of procedure. The indicator will return to showing the outside temperature. Also, the tachometer needle will return to approximately “0”.
NOTE . The REV alarm system does not operate while settings are being en- tered. . The speed-setting mode terminates if 0 rpm is selected. . The speed-setting mode is canceled if the ignition switch is turned to OFF or the vehicle starts moving before the setting procedure is finished. . Speed setting is impossible when the vehicle is moving. . The set engine speed may differ
北米Model "A1920BE-B" EDITED: 2006/ 9/ 19
Black plate (121,1)
Instruments and controls 3-11
This meter displays the odometer and two trip meters. ! Odometer The odometer shows the total distance that the vehicle has been driven. ! Double trip meter
from the engine speed shown by the tachometer. Use the engine speed shown by the tachometer as a rough guide. & Deactivating the REV alarm
system
To deactivate the REV alarm system’s REV indicator light and buzzer functions, set the alarm-level engine speed to 0
(zero) rpm.Meters and gauges (Except WRX-STI)
NOTE Liquid-crystal displays are used in some of the meters and gauges in the combination meter. You will find their indications hard to see if you wear polarized glasses.
& Speedometer The speedometer shows the vehicle speed.
& Odometer/Trip meter
1) Trip meter 2) Odometer
The trip meter shows the distance that the vehicle has been driven since you last set it to zero. To change the mode indication, briefly push the knob. Each press of function alternately.
the knob changes the
– CONTINUED –
北米Model "A1920BE-B" EDITED: 2006/ 9/ 19
3-12 Instruments and controls
To set the trip meter to zero, select the A trip or B trip meter by pushing the knob and keep the knob pushed for more than 2
seconds.CAUTION
To ensure safety, do not attempt to change the function of the indicator during driving, as an accident could result.
NOTE If the connection between the combina- tion meter and battery is broken for any reason such as vehicle maintenance or fuse replacement, the data recorded on the trip meter will be lost.
& Tachometer The tachometer shows the engine speed in thousands of revolutions per minute.
CAUTION
Do not operate the engine with the pointer of the tachometer in the red zone. In this range, fuel injection will be cut by the engine control module to protect the engine from overrev- ving. The engine will resume run- ning normally after the engine speed
Black plate (122,1)
is reduced below the red zone.
NOTE
& Fuel gauge
1)
Low fuel warning light
The fuel gauge shows the approximate amount of fuel remaining in the tank. The gauge does not return to “E” even though the ignition switch is in the “Acc” or “LOCK” position.
The gauge may move slightly during braking, turning or acceleration due to fuel level movement in the tank.
You will see the “FUEL DOOR sign in the fuel gauge. This indicates that the fuel filler door (lid) is located on the right side of the vehicle.
”
! Low fuel warning light The low fuel warning light comes on when the tank is nearly empty [approximately 2.3 US gal (9.0 liters, 1.9 Imp gal]. It only operates when the ignition switch is in the “ON” position. NOTE This light does not go out unless the tank is replenished up to an internal
北米Model "A1920BE-B" EDITED: 2006/ 9/ 19
fuel quantity of approximately 4.0 US gal (15 liters, 3.3 Imp gal).
CAUTION
(Turbo model only) Promptly put fuel in the tank when- ever the low fuel warning light comes on. Engine misfires as a result of an empty tank could cause damage to the engine.
& Temperature gauge
The coolant temperature will vary in accordance with the outside temperature and driving conditions.
We recommend that you drive moderately until the pointer of the temperature gauge reaches near the middle of the range. Engine operation is optimum with the engine coolant at this temperature range and high revving operation when the engine is not warmed up enough should be avoided.
CAUTION
If the pointer exceeds the normal operating range, safely stop the vehicle as soon as possible. See “In case of emergency” in chapter 9.
1) Normal operating range
The temperature gauge shows engine coolant temperature when the ignition switch is in the “ON” position.
Black plate (123,1)
Instruments and controls 3-13
& Outside temperature indica-
tor
1) U.S.-spec. models 2) Canada-spec. models
The outside temperature indicator shows the outside temperature in a range from −22 to 1228F (−30 to 508C). The indicator can give a false reading under any of the following conditions: . When there is too much sun. . During idling; while running at low speeds in a traffic jam; when the engine is restarted immediately following a shut- down. . When the actual outside temperature falls outside the specified indicator range.
北米Model "A1920BE-B" EDITED: 2006/ 9/ 19
3-14 Instruments and controls
Warning and indicator lights
Several of the warning and indicator lights come on momentarily and then go out when the ignition switch is initially turned to the “ON” position. This permits check- ing the operation of the bulbs. Apply the parking brake and turn the ignition switch to the “ON” position. The following lights come on: . Seatbelt warning light . SRS airbag system warning light . Front passenger’s frontal airbag ON indicator light . Front passenger’s frontal airbag OFF indicator light . CHECK ENGINE warning light/Mal- function indicator lamp . Charge warning light . Oil pressure warning light . AT OIL temperature warning light (AT vehicles) . ABS warning light . Brake system warning light . All-Wheel Drive warning light (AWD AT vehicles) . Cruise control indicator light . Cruise control set indicator light
If any lights fail to come on, it indicates a burned-out bulb or a malfunction of the
corresponding system. Consult your authorized SUBARU dealer for repair. & Seatbelt warning light
and chime
the driver has not yet
Your vehicle is equipped with a seatbelt the driver’s seat, as warning device at required by current safety standards. There is a seatbelt warning light in the combination meter. If fastened the seatbelt when the ignition switch is turned to the “ON” position, the seatbelt warning light will flash for 6 seconds, to warn that the seatbelt is unfastened. If the driver’s seatbelt is not fastened, a chime will also sound simultaneously. If the driver’s seatbelt is still not fastened 6
seconds later, the warning light will remain lit for 15 seconds. If the driver’s seatbelt is still not fastened even 15 seconds later (21 seconds after turning ON the ignition switch), the warning lights will alternate between flashing and steady illumination at 15-second intervals, and the chime will sound while the warning light is flashing. Alternate flashing and steady illumination of the warning lights and sounding of the chime will continue until the driver fastens the seatbelt.Black plate (124,1)
NOTE . If the driver unfastens the seatbelt after fastening, the seatbelt warning device operates as follows according to the vehicle speed.
. At speeds lower than approxi- mately 9 mph (15 km/h) The warning light will alternate between flashing and steady illumi- nation at 15-second intervals. The chime will not sound. . At speeds higher than approxi- mately 9 mph (15 km/h) The warning light will alternate between flashing and steady illumi- nation at 15-second intervals and the chime will sound while the warning light is flashing.
. It is possible to cancel the warning operation that follows the 6-second warning after turning ON the ignition switch. When the ignition switch is the turned ON next complete sequence of the warning operation resumes. For further details about canceling the warning operation, please contact your SUBARU dealer.
time, however,
& SRS airbag system
warning light
When the ignition switch is turned to the
北米Model "A1920BE-B" EDITED: 2006/ 9/ 19
“ON” position, the SRS airbag system warning light will come on for approxi- mately 6 seconds and go out. This shows the SRS airbag and SRS side airbag (if equipped) and seatbelt pretensioners are in normal operation.
WARNING
If the warning light exhibits any of the following conditions, there may be a malfunction in the seatbelt pretensioners and/or SRS airbag system. Immediately take your vehi- cle to your nearest SUBARU dealer to have the system checked. Unless checked and properly repaired, the seatbelt pretensioners and/or SRS airbag will not operate properly in the event of a collision, which may increase the risk of injury. . Flashing or flickering of the warn-
ing light
. No illumination of
the warning light when the ignition switch is first turned to the “ON” position the
. Continuous illumination of
warning light
. Illumination of the warning light
while driving
& Front passenger’s frontal
airbag ON and OFF indica- tors
ON or
or
: Front passenger’s frontal airbag ON indicator : Front passenger’s frontal airbag OFF indicator
The front passenger’s frontal airbag ON and OFF indicators show you the status of the front passenger’s SRS frontal airbag. The indicators are located next to the clock in the center portion of the dash- board. When the ignition switch is turned to the “ON” position, both the ON and OFF indicators illuminate for 6 seconds during which time the system is checked. Follow- ing the system check, both indicators
Black plate (125,1)
Instruments and controls 3-15
extinguish for 2 seconds. After that, one of the indicators illuminates depending on the status of the front passenger’s SRS frontal airbag determined by the Subaru advanced frontal airbag system monitor- ing. If the front passenger’s SRS frontal airbag is activated, the passenger’s frontal airbag ON indicator will illuminate while the OFF indicator will remain extinguished. If the front passenger’s SRS frontal airbag the passenger’s frontal is deactivated, airbag ON indicator will remain extin- guished while the OFF indicator will illuminate. With the ignition switch turned to the “ON” position, if both the ON and OFF indica- tors remain lit or extinguished simulta- neously even after the system check period, the system is faulty. Contact your SUBARU dealer immediately for an in- spection.
– CONTINUED –
北米Model "A1920BE-B" EDITED: 2006/ 9/ 19
3-16 Instruments and controls
& CHECK ENGINE warn- ing light/Malfunction in- dicator lamp
CAUTION
If the CHECK ENGINE light comes on while you are driving, have your vehicle checked/repaired by your SUBARU dealer as soon as possi- ble. Continued vehicle operation without having the emission control system checked and repaired as necessary could cause serious da- mage, which may not be covered by your vehicle’s warranty.
If this light comes on steadily or blinks while the engine is running, it may indicate that there is a problem or potential problem somewhere in the emission con- trol system. ! If the light comes on steadily: If the light comes on steadily while driving or does not go out after the engine starts, an emission control system malfunction has been detected. You should have your vehicle checked by an authorized SUBARU dealer immedi- ately.
NOTE This light also comes on when the fuel filler cap is not tightened until it clicks. If you have recently refueled your vehicle, the cause of the CHECK ENGINE warning light/malfunction indicator lamp coming on could be a loose or missing fuel filler cap. Remove the cap and retighten it until it clicks. Make sure nothing is interfering with the sealing of the cap. Tightening the cap will not make the CHECK ENGINE warning light turn off immediately. It may take several driving trips. If the light does not go out, take your vehicle to your authorized SUBARU dealer immediately. ! If the light is blinking: If is blinking while driving, an engine misfire condition has been de- tected which may damage the emission control system. To prevent serious damage to the emis- sion control system, you should do the following. . Reduce vehicle speed. . Avoid hard acceleration. . Avoid steep uphill grades. . Reduce the amount of cargo, if possi- ble. . Stop towing a trailer as soon as possible.
the light
Black plate (126,1)
The CHECK ENGINE warning light may stop blinking and come on steadily after several driving trips. You should have your vehicle checked by an authorized SUBARU dealer immediately. & Charge warning light If this light comes on when the engine is running, it may indicate that the charging system is not working properly.
If the light comes on while driving or does not go out after the engine starts, stop the the first safe opportunity and engine at check the alternator belt. is the belt loose, broken or if is in good condition but the light remains on, contact your nearest SUBARU dealer immedi- ately. & Oil pressure warning
If the belt
light
If this light comes on when the engine is running, it may indicate that the engine oil pressure is low and the lubricating system is not working properly. If the light comes on while driving or does not go out after the engine starts, stop the engine at the first safe opportunity and check the engine oil level. If the oil level is low, add oil immediately. If the engine oil is at the proper level but the light remains on,
北米Model "A1920BE-B" EDITED: 2006/ 9/ 19
contact your nearest SUBARU dealer immediately.
CAUTION
Do not operate the engine with the oil pressure warning light on. This may cause serious engine damage.
er for service immediately. & Rear differential oil
temperature warning light (WRX-STI)
CAUTION
& AT OIL TEMPerature
warning light (AT vehi- cles)
The AT oil temperature warning light comes on when the ignition switch is turned to the “ON” position and goes out after the engine has started. If this light comes on when the engine is running, it may indicate that the automatic transmission fluid temperature is too hot.
If the light comes on while driving, it is unnecessary to stop the vehicle, but avoid driving up steep grades or in stop and go traffic. ! Automatic transmission control
system warning
If the light flashes after the engine starts, it may indicate that the automatic transmis- sion control system is not working prop- erly. Contact your nearest SUBARU deal-
Reduce vehicle speed and park the vehicle in a safe place as soon as possible if the R.DIFF TEMP light comes on. Continued driving with this light on can damage the rear differential and other parts of the powertrain.
it may indicate that
If this light comes on when the engine is running, the rear differential oil temperature is too hot. the driver’s control center At differential will automatically cancel the current torque-distribution ratio setting and adopts its minimum ratio.
this time,
If the light comes on while driving, reduce vehicle speed and stop the vehicle at the nearest safe place. Park the vehicle for several minutes. After the light goes out, you can start driving. If the light does not go out, contact the nearest SUBARU dealer for service.
Black plate (127,1)
Instruments and controls 3-17
NOTE . If the tire pressures are not correct and/or the tires are not all the same size and brand, the rear differential will be heavily loaded when the vehicle is driven, resulting in an abnormally high oil temperature. . The rear differential oil will deterio- rate if its temperature increases en- ough for the rear differential oil tem- perature warning light to come on. It is advisable to have the rear differential oil replaced as soon as possible.
& ABS warning light The ABS warning light comes on when the ignition switch is turned to the “ON” position and goes out after approximately 2 seconds. This is an indication that the ABS system is working properly.
CAUTION
If the warning light behaves as follows, the ABS system may not work properly. When the warning light is on, the ABS function shuts down; however, the conventional brake system con- tinues to operate normally.
– CONTINUED –
北米Model "A1920BE-B" EDITED: 2006/ 9/ 19
3-18 Instruments and controls
. The warning light does not come on when the ignition switch is turned to the “ON” position.
. The warning light comes on when the ignition switch is turned to the “ON” position, but it does not go out even when the vehicle speed exceeds approximately 8
mph (12 km/h).. The warning light comes on dur-
ing driving.
If any of these conditions occur, have the ABS system repaired at the first available opportunity by your SUBARU dealer.
With a vehicle equipped with an EBD system, the ABS warning light comes on together with the brake system warning light if the EBD system becomes faulty. For further details of the EBD system fault warning, refer to “Brake system warning light”. NOTE If described in the following, system may be considered normal. . The warning light comes on right after the engine is started but goes out immediately, remaining off. . The warning light remains on after
the warning light behavior is as the ABS
the engine has been started, but it goes out when the vehicle speed reaches approximately 8 mph (12 km/h). . The warning light comes on during driving, but it goes out immediately and remains off. When driving with an insufficient battery voltage such as when the engine is jump started, the ABS warning light may come on. This is due to the low battery voltage and does not indicate a malfunction. When the battery becomes fully charged, the light will go out. & Brake system warning
light
WARNING
. Driving with the brake system warning light on is dangerous. This indicates your brake system may not be working properly. If the light remains on, we recom- mend that you have the brakes inspected by a SUBARU dealer immediately.
. If at all in doubt about whether the brakes are operating prop- erly, do not drive the vehicle. Have your vehicle towed to the nearest SUBARU dealer for re-
Black plate (128,1)
pair.
This light has the following three functions: ! Parking brake warning The light comes on with the parking brake applied while the ignition switch is in the “ON” position. It goes out when the parking brake is fully released. ! Brake fluid level warning This light comes on when the brake fluid level has dropped to near the “MIN” level of the brake fluid reservoir with the ignition switch in the “ON” position and with the parking brake fully released.
If
this occurs,
If the brake system warning light should come on while driving (with the parking brake fully released and with the ignition switch positioned in “ON”), it could be an indication of leaking of brake fluid or worn brake pads. immediately stop the vehicle at the nearest safe place and check the brake fluid level. If the fluid is below the “MIN” mark in the level reservoir, do not drive the vehicle. Have the vehicle towed to the nearest SUBARU dealer for repair. ! Electronic Brake Force Distribution
(EBD) system warning
The brake system warning light also
北米Model "A1920BE-B" EDITED: 2006/ 9/ 19
illuminates if a malfunction occurs in the EBD system. In that event, it comes on together with the ABS warning light. The EBD system may be malfunctioning if the brake system warning light and ABS warning light illuminate simultaneously during driving. Even if the EBD system fails, the conven- tional braking system will still function. However, the rear wheels will be more prone to locking when the brakes are applied harder than usual and the vehi- cle’s motion may therefore become some- what harder to control. If the brake system warning light and ABS warning light illuminate simultaneously, take the following steps: 1. Stop the vehicle in the nearest safe, flat place. 2. Shut down the engine, apply the parking brake and then restart it. If both 3. Release the parking brake. warning lights go out, the EBD system may be faulty. Drive carefully to the nearest SUBARU dealer and have the system inspected. 4. If both warning lights come on again and stay illuminated after the engine has been restarted, shut down the engine again, apply the parking brake, and check the brake fluid level.
If the brake fluid level is not below the 5. “MIN” mark, the EBD system may be faulty. Drive carefully to the nearest SUBARU dealer and have the system inspected. 6. is below the “MIN” mark, DO NOT drive the vehicle. Instead, have the vehicle towed to the nearest SUBARU dealer for repair. & Door open warning
the brake fluid level
If
light
The door open warning light comes on if any door or the rear gate is not fully closed.
Always make sure this light is out before you start to drive. & All-Wheel Drive warn-
ing light (AWD AT vehicles – if equipped)
The All-Wheel Drive warning light comes on when the ignition switch is turned to the “ON” position and goes out after the engine has started. This light comes on when All-Wheel Drive is disengaged and the drive mechanism is switched to Front Wheel Drive for main- tenance or similar purposes (Non-turbo vehicles).
Black plate (129,1)
Instruments and controls 3-19
It flashes if the vehicle is driven with tires of differing diameters fitted on the wheels or with an excessively low air pressure in any of the tires.
CAUTION
Continuing to drive with the AWD warning light flashing can damage the powertrain. If the AWD warning light starts to flash, promptly park in a safe place and check whether the tires have differing diameters and whether any of the tires has an excessively low inflation pressure.
& Intercooler water spray
warning light (WRX-STI)
This light comes on when the water level in the intercooler water spray tank falls to the lower limit (approximately 0.4 US qt, 0.4 liter, 0.4 Imp qt).
– CONTINUED –
北米Model "A1920BE-B" EDITED: 2006/ 9/ 19
3-20 Instruments and controls
& Selector lever position indi-
cator (AT vehicles)
& High beam indicator
light
This light shows that the headlights are in the high beam mode. This indicator light also comes on when the headlight flasher is operated. & Cruise control indica-
tor light
The cruise control indicator light comes on when the ignition switch is turned to the “ON” position and goes out after approxi- mately 3 seconds. This light comes on when the “CRUISE” main switch is pressed. If you move the cruise control lever or press the main switch button while turning the ignition switch “ON”, the cruise control function is deactivated and the “CRUISE” flashes. To reactivate the indicator light turn the ignition cruise control function, switch back to the “Acc” or “LOCK” position, and then turn it again to the “ON” position. & Cruise control set in-
dicator light
The cruise control set light comes on when the ignition switch is turned to the “ON” position and goes out
indicator
This indicator shows the position of the selector lever. & Turn signal indicator
lights
These lights show the operation of the turn signal or lane change signal. If the indicator lights do not blink or blink rapidly, the turn signal bulb may be burned out. Replace the bulb as soon as possible. Refer to the “Replacing bulbs” section in chapter 11.
Black plate (130,1)
after approximately 3 seconds. This light comes on when vehicle speed has been set. & Driver’s control center differential auto indica- tor light (WRX-STI)
This light functions while the ignition switch is “ON”. When on, it indicates that the driver’s control center differential is set to AUTO mode. It goes off when the driver’s control center differential’s manual mode switch is pressed. For details, refer “Driver’s Control Center to Chapter 7, Differential (DCCD) (WRX-STI)”.
北米Model "A1920BE-B" EDITED: 2006/ 9/ 19
& Driver’s control center differ- ential indicator and warning lights (WRX-STI)
! Indicator lights
! Warning light
Black plate (131,1)
Instruments and controls 3-21
& REV indicator light
(WRX-STI)
This light comes on when the engine speed reaches a level set by driver and when the tachometer needle enters the red zone.
When illuminated, one of these indicator lights indicates the initial limited slip differential (LSD) torque currently selected for the center differential.
failure of
The bottom indicator light “ ” flashes in the the driver’s control event of center differential. Have the vehicle in- spected by your SUBARU dealer. For details, refer to Chapter 7, “Driver’s Con- trol Center Differential (WRX- STI)”. & Lights indicator light
(DCCD)
(WRX-STI)
This light comes on when the headlight switch is placed in the “ ” position.
” or
“
北米Model "A1920BE-B" EDITED: 2006/ 9/ 19
Black plate (132,1)
3-22 Instruments and controls
Clock
Light control switch
& Headlights
The light switch operates only when the ignition switch is in the “ON” position.
WARNING
To prevent battery discharge result- ing from accidentally leaving your lights on when your vehicle is parked, the light switch operates only when the ignition switch is in the “ON” position. In any other position, the vehicle’s lights will be out. If you park your vehicle on a road- side at night, use the hazard warn- ing flasher to alert the other drivers.
To turn on the headlights, turn the knob on the end of the turn signal lever.
first position
Parking lights, instrument panel illumina- tion, tail lights, front side marker lights and license plate light are on.
second position
illumination,
Headlights, parking lights, instrument pa- nel front side marker lights, and license plate light are on.
lights,
tail
To set the hour, press the “H” button. To set the minutes, press the “M” button. To reset the minutes to “00” with a radio time signal, push the “SET” button.
CAUTION
To ensure safety, do not attempt to set the time during driving, as an accident from inadequate attention to the road could result.
北米Model "A1920BE-B" EDITED: 2006/ 9/ 19
Black plate (133,1)
& Headlight flasher
& Daytime running light system
Instruments and controls 3-23
& High/low beam change (dim-
mer)
To change from low beam to high beam, push the turn signal lever forward. When the headlights are on high beam, the high beam indicator light “ ” on the instru- ment panel is also on. To switch back to low beam, pull the lever back to the detent position.
To flash the headlights, pull the lever toward you and then release it. The high beam will stay on for as long as you hold the lever. The headlight flasher works even though the light switch is in the “OFF” position.
When the headlights are on high beam, the high beam indicator light “ ” on the instrument panel also comes on.
CAUTION
Do not hold the lever in the flashing position for more than just a few seconds.
! WRX-STI The low beam headlights, side marker lights, tail lights, parking lights, and license plate lights will automatically come on when the engine has started, under the following conditions: . The parking brake is fully released. . The light switch is in the “OFF” or “ position. . The automatic transmission selector lever is set at other than the “P” position.
”
WARNING
The light switch must always be turned to the “ ” position when it is dark outside.
! Except WRX-STI The low beam headlights will automati- cally come on at reduced brightness when the engine has started, under the following conditions: . The parking brake is fully released. . The light switch is in the “OFF” or “ position. . The automatic transmission selector lever is set at other than the “P” position.
”
– CONTINUED –
北米Model "A1920BE-B" EDITED: 2006/ 9/ 19
Black plate (134,1)
3-24 Instruments and controls
WARNING
Turn signal lever
return automatically to the neutral position when you release it.
The tail lights, parking lights, and side marker lights are not turned on by the daytime running light system. The light switch must always be turned to the “ ” position when it is dark outside.
1) Right turn 2) 3) 4)
Left turn Lane change for right Lane change for left
To activate the right turn signal, push the lever up. To activate the left turn signal turn signal, push the turn signal lever down. When the turn is finished, the lever will return automatically. If the lever does not return after cornering, return the lever to the neutral position by hand.
To signal a lane change, push the turn signal lever up or down slightly and hold it during the lane change. The turn signal indicator lights will flash in the direction of the turn or lane change. The lever will
北米Model "A1920BE-B" EDITED: 2006/ 9/ 19
Black plate (135,1)
Instruments and controls 3-25
Illumination brightness con- trol
Headlight beam leveler (U.S.- spec. WRX-STI)
Parking light switch
” When the headlight switch is in the “ or “ ” position, you can adjust bright- ness of the instrument panel illumination for better visibility.
To brighten, turn the control dial upward. To darken, turn the control dial downward.
The WRX-STI version has High-Intensity Discharge (HID) headlights on the low beam setting. The HID headlights gener- ate more light than conventional halogen headlights. Therefore a driver of an oncoming vehicle may experience too much glare when your headlight beam height adjustment is high due to the vehicle carrying heavy load. The headlight beam leveler can be used to adjust beam height to avoid such a condition.
The higher the number the knob is turned to, the lower the beam becomes.
The parking light switch operates regard- less of the ignition switch position.
By pushing the front end of this switch, following lights will come on. – Parking lights – Front side marker lights – Tail lights – License plate lights
To turn off, push the rear end of parking light switch. Avoid leaving these lights on for a long time because that will run down the battery.
the
北米Model "A1920BE-B" EDITED: 2006/ 9/ 19
3-26 Instruments and controls
Front fog light button (if equipped)
The front fog lights operate only when the headlights are on low beam. Push the front fog light button to turn the front fog lights on. Press the button again to turn them off. The indicator light located on the button will illuminate when the front fog lights are on.
Black plate (136,1)
Wiper and washer
WARNING
In freezing weather, do not use the windshield washer until the wind- shield is sufficiently warmed by the defroster. Otherwise the washer fluid can freeze on the windshield, blocking your view.
CAUTION
. Do not operate the washer con- tinuously for more than 10 sec- onds, or when the washer fluid tank is empty. This may cause overheating of the washer motor. Check the washer fluid level frequently, such as at fuel stops. . Do not operate the wipers when the windshield or rear window is dry. This may scratch the glass, damage the wiper blades and cause the wiper motor to burn out. Before operating the wiper on a dry windshield or rear window, always use the wind- shield washer.
. In freezing weather, be sure that the wiper blades are not frozen to the windshield or rear window before switching on the wipers. Attempting to operate the wiper with the blades frozen to the window glass could cause not only the wiper blades to be damaged but also the wiper mo- tor to burn out. the wiper blades are frozen to the window glass, be sure to operate the defroster, windshield wiper dei- cer (if equipped) or rear window defogger before turning on the wiper.
If
. If the wipers stop during opera- tion because of ice or some other obstruction on the window, the wiper motor could burn out even if the wiper switch is turned off. If this occurs, promptly stop the vehicle in a safe place, turn the ignition switch to the “LOCK” position and clean the window glass to allow proper wiper op- eration.
. Use clean water if windshield washer fluid is unavailable. In areas where water freezes in winter, use SUBARU Windshield Washer Fluid or the equivalent.
北米Model "A1920BE-B" EDITED: 2006/ 9/ 19
face of the windshield or rear window and the wiper blades using a sponge or soft cloth with a neutral detergent or mild-abrasive cleaner. After cleaning, rinse the window glass and wiper blades with clean water. The glass is clean if no beads form on the glass when you rinse with water. . If you cannot eliminate the streaking even after following this procedure, replace the wiper blades with new ones. Refer to the “Replacement of wiper blades” section (chapter 11) for replacement instructions.
(See the “Windshield washer fluid” section in chapter 11.) Also, when driving the vehicle when there are freezing tempera- tures, use non-freezing type wi- per blades.
. Do not clean the wiper blades with gasoline or a solvent, such as paint thinner or benzene. This will cause deterioration of the wiper blades.
NOTE . The wiper operates only when the ignition switch is in the “ON” or “Acc” position. . Clean your wiper blades and win- dow glass periodically with a washer solution to prevent streaking, and to remove accumulations of road salt or road film. Keep the washer button depressed at least for 1 second so that washer solution will be sprinkled all over the windshield or rear window. . Grease, wax, insects or other mate- rial on the windshield or the wiper blade results in jerky wiper operation and streaking on the glass. If you cannot remove those streaks after operating the washer or if the wiper operation is jerky, clean the outer sur-
Black plate (137,1)
Instruments and controls 3-27
& Windshield wiper and washer
switches
! Windshield wipers
OFF: Park
: Intermittent LO: Low speed HI: High speed
To turn the wipers on, push the wiper
