Download PDF Manual

3-3
3-3
3-4
3-4
3-4
3-5
3-5
3-5
3-6
3-6
3-6
3-6
3-7
3-7
3-8
3-9
3-9
Seatbelt warning light and chime ........................ 3-10
SRS airbag system warning light ........................ 3-10
Front passenger’s frontal airbag ON and OFF indicators.........................................................


3-11


CHECK ENGINE warning light/Malfunction


indicator lamp .................................................. 3-12
Charge warning light .......................................... 3-12
Oil pressure warning light .................................. 3-12
AT OIL TEMPerature warning light


(AT vehicles) .................................................... 3-13
ABS warning light .............................................. 3-13


Vehicle Dynamics Control warning light (if equipped)/Vehicle Dynamics Control OFF indicator light (if equipped) .............................. Brake system warning light................................ Door open warning light .................................... Low fuel warning light ....................................... All-Wheel Drive warning light (AT vehicles)......... Vehicle Dynamics Control operation indicator


light (if equipped)............................................. Shift position indicator (AT vehicles) .................. Turn signal indicator lights................................. High beam indicator light ................................... Low tire pressure warning light (if equipped) ...... Cruise control indicator light.............................. Cruise control set indicator light ........................ Clock .................................................................. Light control switch........................................... Headlights ......................................................... High/low beam change (dimmer) ........................ Headlight flasher ............................................... Daytime running light system............................. Turn signal lever ................................................ Illumination brightness control......................... Headlight beam leveler (Vehicle with HID


headlights) ...................................................... Parking light switch........................................... Front fog light button ........................................


3-14
3-15
3-16
3-16
3-16


3-16
3-17
3-17
3-17
3-17
3-19
3-19
3-19
3-20
3-20
3-21
3-21
3-21
3-22
3-23


3-23
3-23
3-24


北米Model "A8130BE-B" EDITED: 2007/ 7/ 25


Black plate (6,1)


Instruments and controls


Wiper and washer .............................................. 3-24
Windshield wiper and washer switches ............... 3-25
Rear window wiper and washer switch................ 3-26
Windshield wiper deicer (if equipped) .............. 3-27
Rear window defogger button........................... 3-28


Mirrors ................................................................ Inside mirror...................................................... Outside mirrors ................................................. Tilt steering wheel ............................................. Horn....................................................................


3-29
3-29
3-30
3-32
3-32


北米Model "A8130BE-B" EDITED: 2007/ 7/ 25


Ignition switch


WARNING


. Never turn the ignition switch to “LOCK” while the vehicle is being driven or towed because that will lock the steering wheel, preventing steering control. And when the engine is turned off, it takes a much greater effort than usual to steer.


. Before leaving the vehicle, al- ways remove the key from the ignition switch for safety and never allow an unattended child to remain in the vehicle. Failure to follow this procedure could result in injury to a child or others. Children could operate the power windows, the sunroof or other controls or even make the vehicle move.


The ignition switch has four positions: LOCK, Acc, ON and START.


NOTE . Keep the ignition switch in the “LOCK” position when the engine is not running. . Using electrical accessories for a long time with the ignition switch in the “ON” or “Acc” position can cause the battery to go dead. If the ignition switch will not move from the “LOCK” position to the “Acc” position, turn the steering wheel slightly to the left and right as you turn the ignition switch. . If the key is attached to a keyholder or to a large bunch of other keys, centrifugal force may act on it as the vehicle moves, resulting in unwanted turning of the ignition switch. Also, if a large keyholder is attached to the key,


Black plate (117,1)


Instruments and controls 3-3


your knees or hands may accidentally touch it in a way that turns the ignition switch.


& LOCK The key can only be inserted or removed in this position. The ignition switch will lock the steering wheel when you remove the key. turn the If steering wheel slightly to the right and left as you turn the key. ! Automatic transmission vehicles


turning the key is difficult,


– CONTINUED –


北米Model "A8130BE-B" EDITED: 2007/ 7/ 25


3-4 Instruments and controls


The key can be turned from “Acc” to “LOCK” only when the selector lever is in the “P” position. ! Manual transmission vehicles


Black plate (118,1)


NOTE The engine may not start in the follow- ing cases:


while turning it.


& Acc In this position the electrical accessories (radio, accessory power outlet, etc.) can be used.


& ON This is the normal operating position after the engine is started.


& START


CAUTION


Do not turn the ignition switch to the “START” position while the engine is running.


. The key grip is touching another key or a metallic key holder.


The engine is started in this position. The starter cranks the engine to start it. When the key is released (after the engine has started), the key automatically returns to the “ON” position. ! For models with immobilizer If you fail to start your engine with your registered key, once pull out the key (at this time, light blinks), and then insert the key in the ignition switch and turn it to the “START” position and again try to start your engine.


the security indicator


The key can be turned from “Acc” to “LOCK” only when the key is pushed in


. The key is near another key that


北米Model "A8130BE-B" EDITED: 2007/ 7/ 25


Black plate (119,1)


Instruments and controls 3-5


contains an immobilizer transponder. . The key is near or touching another transmitter.


the “P” position: 1. Take out the screwdriver.


Take your vehicle to the nearest SUBARU dealer immediately to have the key inter- lock system repaired.


& Key reminder chime The reminder chime sounds when the driver’s door opens and the key is in the “LOCK” or “Acc” positions. The chime stops when the key is removed from the ignition switch. NOTE The ignition switch light flashes when the reminder chime sounds.


& Ignition switch light (if


equipped)


For easy access to the ignition switch in the dark, the ignition switch light comes on when the driver’s door is opened. After closing the door, the light remains lit for 5
seconds and then dims before it goes out. The light flashes if you insert the key into the ignition switch with the driver’s door open.


& Key interlock release (AT ve-


hicles only)


If the key can not be turned to the “LOCK” position even when the selector lever is in


2. Remove the cover under the steering column using a Phillips screwdriver.


3. Turn the ignition key while pressing the key interlock release lever.


北米Model "A8130BE-B" EDITED: 2007/ 7/ 25


Black plate (120,1)


3-6 Instruments and controls


Hazard warning flasher


Meters and gauges & Speedometer The speedometer shows the vehicle speed.


& Odometer/Trip meter


knob. ! Odometer The odometer shows the total distance that the vehicle has been driven. ! Double trip meter


The hazard warning flasher is used to warn other drivers when you have to park your vehicle under emergency conditions. The hazard warning flasher works with the ignition switch in any position.


To turn on the hazard warning flasher, push the hazard warning button on the instrument panel. To turn off the flasher, push the button again. NOTE When the hazard warning flasher is on, the turn signals do not work.


1) Trip meter 2) Odometer


This meter displays the odometer and two trip meters when the ignition switch is in the “ON” position. NOTE Even with the ignition switch in the “Acc” or “LOCK” position, the od- ometer and trip meters are displayed for 10 seconds when you press the


1) A trip meter 2) B trip meter


The trip meter shows the distance that the vehicle has been driven since you last set it to zero. To change the mode indication, briefly push the knob. Each press of function alternately.


the knob changes the


To set the trip meter to zero, select the A


北米Model "A8130BE-B" EDITED: 2007/ 7/ 25


Black plate (121,1)


Instruments and controls 3-7


trip or B trip meter by pushing the knob and keep the knob pushed for more than 2
seconds.


& Tachometer The tachometer shows the engine speed in thousands of revolutions per minute.


& Fuel gauge


CAUTION


To ensure safety, do not attempt to change the function of the indicator during driving, as an accident could result.


NOTE If the connection between the combina- tion meter and battery is broken for any reason such as vehicle maintenance or fuse replacement, the data recorded on the trip meter will be lost.


CAUTION


Do not operate the engine with the pointer of the tachometer in the red zone. In this range, fuel injection will be cut by the engine control module to protect the engine from overrev- ving. The engine will resume run- ning normally after the engine speed is reduced below the red zone.


NOTE (non-turbo models only) To protect the engine while the “P” or “N” position is selected (for AT models) or while the shift lever is in neutral (for MT models), the engine is controlled so that the engine speed does not become too high even if the accelerator pedal is fully depressed.


1)


Low fuel warning light


The fuel gauge shows the approximate amount of fuel remaining in the tank. The gauge does not return to “E” even though the ignition switch is in the “Acc” or “LOCK” position.


The gauge may move slightly during braking, turning or acceleration due to fuel level movement in the tank.


– CONTINUED –


北米Model "A8130BE-B" EDITED: 2007/ 7/ 30


Black plate (122,1)


3-8 Instruments and controls


NOTE


” sign near the


You will see the “ fuel gauge. This indicates that the fuel filler door (lid) is located on the right side of the vehicle. ! Low fuel warning light The low fuel warning light comes on when the tank is nearly empty [approximately 2.3 US gal (9.0 liters, 1.9 Imp gal)]. It only operates when the ignition switch is in the “ON” position. When this light illuminates, fill the fuel tank immediately. NOTE This light does not go out unless the tank is replenished up to an internal


fuel quantity of approximately 4.0 US gal (15 liters, 3.3 Imp gal).


CAUTION


fuel


in the tank Immediately put whenever the low fuel warning light comes on. Engine misfires as a result of an empty tank could cause damage to the engine.


& Temperature gauge


The coolant temperature will vary in accordance with the outside temperature and driving conditions.


We recommend that you drive moderately until the pointer of the temperature gauge reaches near the middle of the range. Engine operation is optimum with the engine coolant at this temperature range and high revving operation when the engine is not warmed up enough should be avoided.


CAUTION


If the pointer exceeds the normal operating range, safely stop the vehicle as soon as possible. See “In case of emergency” in chapter 9.


1) Normal operating range


The temperature gauge shows engine coolant temperature when the ignition switch is in the “ON” position.


北米Model "A8130BE-B" EDITED: 2007/ 7/ 25


& Outside temperature indica-


tor


MT vehicles 1) U.S.-spec. models 2) Canada-spec. models


AT vehicles 1) U.S.-spec. models 2) Canada-spec. models


The outside temperature indicator is lo- cated below the odometer/trip meter. The indicator can indicate an outside tempera- ture ranging from −22 to 1228F (−30 to 508C). The indicator can give a false reading under any of the following conditions: . When there is too much sun. . During idling; while running at low speeds in a traffic jam; when the engine is restarted immediately following a shut- down. . When the actual outside temperature falls outside the specified indicator range.


Black plate (123,1)


Instruments and controls 3-9


Warning and indicator lights


Several of the warning and indicator lights come on momentarily and then go out when the ignition switch is initially turned to the “ON” position. This permits check- ing the operation of the bulbs. Apply the parking brake and turn the ignition switch to the “ON” position. The following lights come on:


: Seatbelt warning light


: SRS airbag system warning light


: Front passenger’s frontal airbag


ON indicator light


: Front passenger’s frontal airbag


OFF indicator light


: CHECK ENGINE warning light/Mal-


function indicator lamp


: Charge warning light


: Oil pressure warning light


: AT OIL temperature warning light (AT


vehicles)


: ABS warning light


: Brake system warning light


: All-Wheel Drive warning light


vehicles)


(AT


– CONTINUED –


北米Model "A8130BE-B" EDITED: 2007/ 7/ 25


Black plate (124,1)


3-10 Instruments and controls


: Vehicle Dynamics Control operation


indicator light (if equipped)


: Vehicle Dynamics Control warning light (if equipped)/Vehicle Dynamics Control OFF indicator light (if equipped)


: Low tire pressure warning light


equipped)


(if


: Cruise control indicator light


: Cruise control set indicator light


If any lights fail to come on, it indicates a burned-out bulb or a malfunction of the corresponding system. Consult your authorized SUBARU dealer for repair. & Seatbelt warning light


and chime


the driver has not yet


Your vehicle is equipped with a seatbelt the driver’s seat, as warning device at required by current safety standards. There is a seatbelt warning light in the combination meter. If fastened the seatbelt when the ignition switch is turned to the “ON” position, the seatbelt warning light will flash for 6 seconds, to warn that the seatbelt is unfastened. If the driver’s seatbelt is not fastened, a chime will also sound simultaneously.


If the driver’s seatbelt is still not fastened 6
seconds later, the warning light will remain lit for 15 seconds. If the driver’s seatbelt is still not fastened even 15 seconds later (21 seconds after turning ON the ignition switch), the warning lights will alternate between flashing and steady illumination at 15-second intervals, and the chime will sound while the warning light is flashing. Alternate flashing and steady illumination of the warning lights and sounding of the chime will continue until the driver fastens the seatbelt. NOTE . If the driver unfastens the seatbelt after fastening, the seatbelt warning device operates as follows according to the vehicle speed.


. At speeds lower than approxi- mately 9 mph (15 km/h) The warning light will alternate between flashing and steady illumi- nation at 15-second intervals. The chime will not sound. . At speeds higher than approxi- mately 9 mph (15 km/h) The warning light will alternate between flashing and steady illumi- nation at 15-second intervals and the chime will sound while the warning light is flashing.


. It is possible to cancel the warning operation that follows the 6-second warning after turning ON the ignition switch. When the ignition switch is turned ON next the complete sequence of warning opera- tion resumes. For further details about canceling the warning operation, please contact your SUBARU dealer.


time, however,


& SRS airbag system


warning light


When the ignition switch is turned to the “ON” position, the SRS airbag system warning light will come on for approxi- mately 6 seconds and go out. This shows the SRS frontal airbag and SRS side airbag and seatbelt pretensioners are in normal operation.


WARNING


If the warning light exhibits any of the following conditions, there may be a malfunction in the seatbelt pretensioners and/or SRS airbag system. Immediately take your vehi- cle to your nearest SUBARU dealer to have the system checked. Unless checked and properly repaired, the seatbelt pretensioners and/or SRS airbags will operate improperly (e.g.


北米Model "A8130BE-B" EDITED: 2007/ 7/ 25


SRS airbags may inflate in a very minor collision or not inflate in a severe collision), which may in- crease the risk of injury. . Flashing or flickering of the warn-


ing light


& Front passenger’s frontal


airbag ON and OFF indica- tors


. No illumination of


the warning light when the ignition switch is first turned to the “ON” position the


. Continuous illumination of


warning light


. Illumination of the warning light


while driving


1) U.S.-spec. models 2) Canada-spec. models


or


or


: Front passenger’s frontal airbag ON indicator : Front passenger’s frontal airbag OFF indicator


The front passenger’s frontal airbag ON and OFF indicators show you the status of the front passenger’s SRS frontal airbag. The indicators are located next to the clock in the central portion of the instru- ment panel. When the ignition switch is turned to the “ON” position, both the ON and OFF


Black plate (125,1)


Instruments and controls 3-11


indicators illuminate for 6 seconds during which time the system is checked. Follow- ing the system check, both indicators extinguish for 2 seconds. After this, one of the indicators illuminates depending on the status of the front passenger’s SRS frontal airbag reached by the Subaru advanced frontal airbag system monitor- ing. If the front passenger’s SRS frontal airbag is activated, the passenger’s frontal airbag ON indicator will illuminate while the OFF indicator will remain extinguished. If the front passenger’s SRS frontal airbag the passenger’s frontal is deactivated, airbag ON indicator will remain extin- guished while the OFF indicator will illuminate. With the ignition switch turned to the “ON” position, if both the ON and OFF indica- tors remain lit or extinguished simulta- neously even after the system check period, the system is faulty. Contact your SUBARU dealer immediately for an in- spection.


– CONTINUED –


北米Model "A8130BE-B" EDITED: 2007/ 7/ 30


3-12 Instruments and controls


& CHECK ENGINE warn- ing light/Malfunction in- dicator lamp


CAUTION


If the CHECK ENGINE light comes on while you are driving, have your vehicle checked/repaired by your SUBARU dealer as soon as possi- ble. Continued vehicle operation without having the emission control system checked and repaired as necessary could cause serious da- mage, which may not be covered by your vehicle’s warranty.


If this light comes on steadily or blinks while the engine is running, it may indicate that there is a problem or potential problem somewhere in the emission con- trol system. ! If the light comes on steadily: If the light comes on steadily while driving or does not go out after the engine starts, an emission control system malfunction has been detected.


You should have your vehicle checked by an authorized SUBARU dealer immedi- ately.


NOTE This light also comes on when the fuel filler cap is not tightened until it clicks. If you have recently refueled your vehicle, the cause of the CHECK ENGINE warning light/malfunction indicator lamp coming on could be a loose or missing fuel filler cap. Remove the cap and retighten it until it clicks. Make sure nothing is interfering with the sealing of the cap. Tightening the cap will not make the CHECK ENGINE warning light turn off immediately. It may take several driving trips. If the light does not go out, take your vehicle to your authorized SUBARU dealer immediately. ! If the light is blinking: If is blinking while driving, an engine misfire condition has been de- tected which may damage the emission control system. To prevent serious damage to the emis- sion control system, you should do the following. . Reduce vehicle speed. . Avoid hard acceleration. . Avoid steep uphill grades. . Reduce the amount of cargo, if possi- ble. . Stop towing a trailer as soon as possible.


the light


Black plate (126,1)


The CHECK ENGINE warning light may stop blinking and come on steadily after several driving trips. You should have your vehicle checked by an authorized SUBARU dealer immediately. & Charge warning light If this light comes on when the engine is running, it may indicate that the charging system is not working properly.


If the light comes on while driving or does not go out after the engine starts, stop the the first safe opportunity and engine at check the alternator belt. is the belt loose, broken or if is in good condition but the light remains on, contact your nearest SUBARU dealer immedi- ately. & Oil pressure warning


If the belt


light


CAUTION


Do not operate the engine with the oil pressure warning light on. This may cause serious engine damage.


If this light comes on when the engine is running, it may indicate that the engine oil pressure is low and the lubricating system is not working properly.


北米Model "A8130BE-B" EDITED: 2007/ 7/ 25


If the light comes on while driving or does not go out after the engine starts, stop the engine at the first safe opportunity and check the engine oil level. If the oil level is low, add oil immediately. If the engine oil is at the proper level but the light remains on, contact your nearest SUBARU dealer immediately. & AT OIL TEMPerature


warning light (AT vehi- cles)


The AT oil temperature warning light comes on when the ignition switch is turned to the “ON” position and goes out after the engine has started. If this light comes on when the engine is running, it may indicate that the automatic transmission fluid temperature is too hot.


If the light comes on while driving, immediately stop the vehicle in a safe place and let the warning light goes off. ! Automatic transmission control


the engine idle until


system warning


If the light flashes after the engine starts, it may indicate that the automatic transmis- sion control system is not working prop- erly. Contact your nearest SUBARU deal- er for service immediately.


& ABS warning light The ABS warning light comes on when the ignition switch is turned to the “ON” position and goes out after approximately 2 seconds. This is an indication that the ABS system is working properly.


CAUTION


If the warning light behaves as follows, the ABS system may not work properly. When the warning light is on, the ABS function shuts down; however, the conventional brake system con- tinues to operate normally. . The warning light does not come on when the ignition switch is turned to the “ON” position.


. The warning light comes on when the ignition switch is turned to the “ON” position, but it does not go out even when the vehicle speed exceeds approximately 8
mph (12 km/h).


. The warning light comes on dur-


ing driving.


If any of these conditions occur, have the ABS system repaired at


Black plate (127,1)


Instruments and controls 3-13


the first available opportunity by your SUBARU dealer.


the warning light behavior is as the ABS


The ABS warning light comes on together with the brake system warning light if the EBD system becomes faulty. For further details of the EBD system fault warning, refer to “Brake system warning light”. NOTE If described in the following, system may be considered normal. . The warning light comes on right after the engine is started but goes out immediately, remaining off. . The warning light remains on after the engine has been started, but it goes out when the vehicle speed reaches approximately 8 mph (12 km/h). . The warning light comes on during driving, but it goes out immediately and remains off. When driving with an insufficient battery voltage such as when the engine is jump started, the ABS warning light may come on. This is due to the low battery voltage and does not indicate a malfunction. When the battery becomes fully charged, the light will go out.


– CONTINUED –


北米Model "A8130BE-B" EDITED: 2007/ 7/ 25


Black plate (128,1)


3-14 Instruments and controls


& Vehicle Dynamics


Control warning light (if equipped)/Vehicle Dy- namics Control OFF in- dicator light (if equipped)


This warning light has the function of indicating faults in the Vehicle Dynamics Control system and the function of indicat- ing that the Vehicle Dynamics Control system has been deactivated. It comes on in the event of a fault in the system and is on when the system is not operating. This warning light comes on when the ignition switch is turned to the “ON” position and goes out after the engine has started. It indicates that the Vehicle Dynamics Control system is in normal operation. ! Vehicle Dynamics Control warning


light


The Vehicle Dynamics Control system is probably inoperative under any of the following conditions. Have your vehicle checked at a SUBARU dealer immedi- ately. The warning light does not come on when the ignition switch is turned to the “ON” position.


the electrical circuit of


. The warning light comes on while the vehicle is running. . If the Vehicle Dynamics Control system itself becomes faulty, the warning light only comes on. At this time, the ABS (Anti-lock Brake Sys- tem) remains fully operational. . The warning light comes on when the electronic control system of the ABS/ Vehicle Dynamics Control system be- comes faulty.


The Vehicle Dynamics Control system provides its ABS control through the the ABS system. electrical circuit of Accordingly, if the ABS is inoperative, the Vehicle Dynamics Control system be- comes unable to provide ABS control. As a result, the Vehicle Dynamics Control system also becomes inoperative, caus- ing the warning light to come on. Though both the Vehicle Dynamics Control and ABS systems are inoperative in this case, the ordinary functions of the brake system are still available. You will be safe while driving with this condition, but have your vehicle checked at a SUBARU dealer as soon as possible. NOTE the warning light behavior is as If shown in the following, the Vehicle Dynamics Control system may be con-


sidered normal. . The warning light comes on right after the engine is started but goes out immediately, remaining off. . The warning light comes on after engine startup and goes off while the vehicle is subsequently being driven. . The warning light comes on during driving, but it goes out immediately and remains off. ! Vehicle Dynamics Control OFF in-


dicator light


. It comes on when the Vehicle Dy- namics Control OFF switch is pressed. . It also comes on when the Vehicle Dynamics Control system is deactivated. NOTE . The light may stay on for a while after the engine has been started, especially in cold weather. This does not indicate the existence of a problem. The light should go out as soon as the engine has warmed up. . The indicator light comes on when the engine has developed a problem and the Malfunction indicator light is on. The Vehicle Dynamics Control system is probably faulty under the following condi- tion. Have your vehicle checked at a


北米Model "A8130BE-B" EDITED: 2007/ 7/ 25


SUBARU dealer as soon as possible. . The light does not go out even after the lapse of several minutes (the engine has warmed up) after the engine has started. & Brake system warning


light


WARNING


. Driving with the brake system warning light on is dangerous. This indicates your brake system may not be working properly. If the light remains on, have the brakes inspected by a SUBARU dealer immediately.


. If at all in doubt about whether the brakes are operating prop- erly, do not drive the vehicle. Have your vehicle towed to the nearest SUBARU dealer for re- pair.


This light has the following three functions: ! Parking brake warning The light comes on with the parking brake applied while the ignition switch is in the “ON” position. It goes out when the parking brake is fully released.


! Brake fluid level warning This light comes on when the brake fluid level has dropped to near the “MIN” level of the brake fluid reservoir with the ignition switch in the “ON” position and with the parking brake fully released.


If


this occurs,


If the brake system warning light should come on while driving (with the parking brake fully released and with the ignition switch positioned in “ON”), it could be an indication of leaking of brake fluid or worn brake pads. immediately stop the vehicle at the nearest safe place and check the brake fluid level. If the fluid is below the “MIN” mark in the level reservoir, do not drive the vehicle. Have the vehicle towed to the nearest SUBARU dealer for repair. ! Electronic Brake Force Distribution


(EBD) system warning


The brake system warning light also illuminates if a malfunction occurs in the EBD system. In that event, it comes on together with the ABS warning light. The EBD system may be malfunctioning if the brake system warning light and ABS warning light illuminate simultaneously during driving. Even if the EBD system fails, the conven- tional braking system will still function. the rear wheels will be more However,


Black plate (129,1)


Instruments and controls 3-15


prone to locking when the brakes are applied harder than usual and the vehi- cle’s motion may therefore become some- what harder to control. If the brake system warning light and ABS warning light illuminate simultaneously, take the following steps: 1. Stop the vehicle in the nearest safe, flat place. 2. Shut down the engine, then restart it. 3. Release the parking brake. If both warning lights go out, the EBD system may be faulty. Drive carefully to the nearest SUBARU dealer and have the system inspected. 4. If both warning lights come on again and stay illuminated after the engine has been restarted, shut down the engine again, apply the parking brake, and check the brake fluid level. If the brake fluid level is not below the 5. “MIN” mark, the EBD system may be faulty. Drive carefully to the nearest SUBARU dealer and have the system inspected. 6. is below the “MIN” mark, DO NOT drive the vehicle. Instead, have the vehicle towed to the nearest SUBARU dealer for repair.


the brake fluid level


If


– CONTINUED –


北米Model "A8130BE-B" EDITED: 2007/ 7/ 25


3-16 Instruments and controls


& Door open warning


light


The door open warning light illuminates if any door or the rear gate is not fully closed.


Always make sure this light is out before you start to drive. & Low fuel warning light The low fuel warning light illuminates when the tank is nearly empty [approxi- mately 2.3 US gal (9.0 liters, 1.9 Imp gal)]. It only operates when the ignition switch is in the “ON” position. When this light illuminates, fill the fuel tank immediately. NOTE This light does not go out unless the tank is replenished up to an internal fuel quantity of approximately 4.0 US gal (15 liters, 3.3 Imp gal).


& All-Wheel Drive warn- ing light (AT vehicles)


WARNING


Continued driving with the AWD warning light flashing can lead to powertrain damage. the AWD


If


warning light flashes, promptly park in a safe place then check whether all four tires are the same diameter and whether any of the tires has a puncture or has lost air pressure for some other reason.


The All-Wheel Drive warning light comes on when the ignition switch is turned to the “ON” position and goes out after engine has started. ! For vehicles with Vehicle Dynamics


Control system


This light flashes if the vehicle is driven with tires of different diameters or with the air pressure excessively low in any of its tires. ! For vehicles without Vehicle Dy-


namics Control system


This light comes on when All-Wheel Drive is disengaged and the drive mechanism is switched to Front Wheel Drive for main- tenance or similar purposes. This light flashes if the vehicle is driven with tires of different diameters or with the air pressure excessively low in any of its tires.


Black plate (130,1)


& Vehicle Dynamics


Control operation indi- cator light (if equipped)


This light comes on when the ignition switch is ON and goes out approximately 2 seconds later. It blinks when the skid suppression func- tion is activated. It illuminates when only the traction control function is operating.


The Vehicle Dynamics Control system is probably faulty under any of the following conditions. Have your vehicle checked at a SUBARU dealer immediately. . The light does not come on when the ignition switch is turned to the “ON” position. . The light does not go out even after a period of approximately 2 seconds after the ignition switch has been turned to the “ON” position.


北米Model "A8130BE-B" EDITED: 2007/ 7/ 25


& Shift position indicator (AT


vehicles)


& High beam indicator


light


This light shows that the headlights are in the high beam mode. This indicator light also comes on when the headlight flasher is operated. & Low tire pressure


warning light (if equipped)


When the ignition switch is turned to the “ON” position, the low tire pressure warn- ing light will come on for approximately 2
seconds to check that the tire pressure monitoring system (TPMS) is functioning properly. If there is no problem and all tires are properly inflated, the light will go out. Each tire, including the spare (if provided), should be checked monthly when cold and inflated to the inflation pressure recommended by the vehicle manufac- turer on the vehicle placard or tire inflation pressure label. (If your vehicle has tires of a different size than the size indicated on the vehicle placard or tire inflation pres- sure label, you should determine the proper inflation pressure for those tires.)


As an added safety feature, your vehicle has been equipped with a tire pressure monitoring system (TPMS) that illuminates


This indicator shows the position of the shift lever. & Turn signal indicator


lights


These lights show the operation of the turn signal or lane change signal. If the indicator lights do not blink or blink rapidly, the turn signal bulb may be burned out. Replace the bulb as soon as possible. Refer to the “Replacing bulbs” section in chapter 11.


Black plate (131,1)


Instruments and controls 3-17


a low tire pressure telltale when one or more of your tires is significantly under- inflated. Accordingly, when the low tire pressure telltale illuminates, you should stop and check your tires as soon as possible, and inflate them to the proper pressure. Driving on a significantly under- inflated tire causes the tire to overheat and can lead to tire failure. Under-inflation also reduces fuel efficiency and tire tread life, and may affect the vehicle’s handling and stopping ability. the TPMS is not a Please note that tire maintenance, substitute for proper is the driver’s responsibility to and it maintain correct tire pressure, even if under-inflation has not reached the level to trigger illumination of the TPMS low tire pressure telltale. Your vehicle has also been equipped with a TPMS malfunction indicator to indicate when the system is not operating properly. The TPMS malfunction indicator is com- bined with the low tire pressure telltale. When the system detects a malfunction, the telltale will flash for approximately one minute and then remain continuously illuminated. This sequence will continue upon subsequent vehicle start-ups as long as the malfunction exists. When the malfunction indicator is illuminated, the system may not be able to detect or signal


– CONTINUED –


北米Model "A8130BE-B" EDITED: 2007/ 7/ 25


3-18 Instruments and controls


low tire pressure as intended. TPMS malfunctions may occur for a variety of reasons, including the installation of re- placement or alternate tires or wheels on the vehicle that prevent the TPMS from functioning properly. Always check the TPMS malfunction telltale after replacing one or more tires or wheels on your vehicle to ensure that the replacement or alternate tires and wheels allow the TPMS to continue to function properly. Should the warning light illuminate stea- dily after blinking for approximately one minute, have the system inspected by your nearest SUBARU dealer as soon as possible.


Black plate (132,1)


WARNING


If this light does not come on briefly after the ignition switch is turned ON or the light illuminates steadily after blinking for approximately one min- ute, you should have your Tire P r e s s u r e M o n i t o r i n g S y s t e m checked at a SUBARU dealer as soon as possible. If this light comes on while driving, never brake suddenly and keep driving straight ahead while gradu- ally reducing speed. Then slowly pull off the road to a safe place. Otherwise an accident involving serious vehicle damage and serious personal injury could occur. this light still comes on while If driving after adjusting the tire pres- sure, a tire may have significant damage and a fast leak that causes the tire to lose air rapidly. If you have a flat tire, replace it with a spare tire as soon as possible. When a spare tire is mounted or a wheel rim is replaced without the original pressure sensor/transmitter being transferred, the Low tire pres- sure warning light will illuminates steadily after blinking for approxi- mately one minute. This indicates


the TPMS is unable to monitor all four road wheels. Contact your SUBARU dealer as soon as possible for tire and sensor replacement and/ or system resetting. the light illuminates steadily after blinking for approximately one minute, promptly contact a SUBARU dealer to have the system inspected.


If


CAUTION


The tire pressure monitoring system is NOT a substitute for manually checking tire pressure. The tire pressure should be checked peri- odically (at least monthly) using a tire gauge. After any change to tire pressure(s), the tire pressure mon- itoring system will not re-check tire inflation pressures until the vehicle is first driven more than 20 mph (32
km/h). After adjusting the tire pres- sures, increase the vehicle speed to at least 20 mph (32 km/h) to start the TPMS re-checking of the tire infla- tion pressures. If the tire pressures are now above the severe low pressure threshold, the low tire pressure warning light should go off a few minutes later. Therefore, be sure to install the specified size for


北米Model "A8130BE-B" EDITED: 2007/ 7/ 25


the front and rear tires.


& Cruise control indica-


tor light


The cruise control indicator light comes on when the ignition switch is turned to the “ON” position and goes out after approxi- mately 3 seconds. This light comes on when the “CRUISE” main switch is pressed. NOTE . If you move the cruise control lever or press the main switch button while turning the ignition switch “ON”, the cruise control function is deactivated and the “CRUISE” indicator light flashes. To reactivate the cruise control function, turn the ignition switch back to the “Acc” or “LOCK” position, and then turn it again to the “ON” position. . If this indicator light and the “ ” indicator light flash simultaneously during driving, have the vehicle checked by your nearest SUBARU dealer.


Black plate (133,1)


Instruments and controls 3-19


& Cruise control set in-


dicator light


Clock


indicator


The cruise control set light comes on when the ignition switch is turned to the “ON” position and goes out after approximately 3 seconds. This light comes on when vehicle speed has been set.


To adjust the clock, open the small article storage compartment in the dashboard with the vehicle parked in a safe place.


To set the hour, press the “H” button. To – CONTINUED –


北米Model "A8130BE-B" EDITED: 2007/ 7/ 30


3-20 Instruments and controls


set the minutes, press the “M” button. To reset the minutes to “00” with a radio time signal, push the “Reset” button.


CAUTION


To ensure safety, do not attempt to set the time while driving, as an accident from inadequate attention to the road could result.


NOTE The clock uses a liquid crystal display. You will find time indications hard to see if you wear polarized glasses.


Black plate (134,1)


Light control switch


& Headlights


The light switch operates only when the ignition switch is in the “ON” position.


WARNING


To prevent battery discharge result- ing from accidentally leaving your lights on when your vehicle is parked, the light switch operates only when the ignition switch is in the “ON” position. In any other position, the vehicle’s lights will be out. If you park your vehicle on a road- side at night, use the hazard warn- ing flasher to alert the other drivers.


To turn on the headlights, turn the knob on the end of the turn signal lever.


first position:


illumina- Parking lights, instrument panel tion, front side marker lights, tail lights and license plate light are on.


second position:


Headlights, parking lights, instrument pa- nel illumination, front side marker lights, tail lights, and license plate light are on.


北米Model "A8130BE-B" EDITED: 2007/ 7/ 25


& High/low beam change (dim-


mer)


& Headlight flasher


To change from low beam to high beam, push the turn signal lever forward. When the headlights are on high beam, the high beam indicator light “ ” on the instru- ment panel is also on. To switch back to low beam, pull the lever back to the detent position.


To flash the headlights, pull the lever toward you and then release it. The high beam will stay on for as long as you hold the lever. The headlight flasher works even though the lighting switch is in the “OFF” position.


When the headlights are on high beam, the high beam indicator light “ ” on the instrument panel also comes on.


CAUTION


Do not hold the lever in the flashing position for more than just a few seconds.


Black plate (135,1)


Instruments and controls 3-21


& Daytime running light system ! Canada-spec. 2.5XT


WARNING


The parking lights, and side marker lights are not turned on by the daytime running light system. The light switch must always be turned to the “ ” position when it is dark outside.


The low beam headlights and tail lights will automatically come on when the engine has started, under the following condi- tions: . The parking brake is fully released. . The light switch is in the “OFF” or “ position. . The automatic transmission selector lever is set at other than the “P” position. ! All models except Canada-spec.



2.5XT


WARNING


The tail lights, parking lights, and side marker lights are not turned on by the daytime running light system. The light switch must always be turned to the “ ” position when it


– CONTINUED –


北米Model "A8130BE-B" EDITED: 2007/ 7/ 25


Black plate (136,1)


3-22 Instruments and controls


is dark outside.


Turn signal lever


return automatically to the neutral position when you release it.


The low beam headlights will automati- cally come on at reduced brightness when the engine has started, under the following conditions: . The parking brake is fully released. . The light switch is in the “OFF” or “ position. . The automatic transmission selector lever is set at other than the “P” position.



1) Right turn 2) 3) 4)


Left turn Lane change for right Lane change for left


To activate the right turn signal, push the lever up. To activate the left turn signal turn signal, push the turn signal lever down. When the turn is finished, the lever will return automatically. If the lever does not return after cornering, return the lever to the neutral position by hand.


To signal a lane change, push the turn signal lever up or down slightly and hold it during the lane change. The turn signal indicator lights will flash in the direction of the turn or lane change. The lever will


北米Model "A8130BE-B" EDITED: 2007/ 7/ 25


Black plate (137,1)


Instruments and controls 3-23


Illumination brightness con- trol


Headlight beam leveler (Ve- hicle with HID headlights)


Parking light switch


” When the headlight switch is in the “ or “ ” position, you can adjust bright- ness of the instrument panel illumination for better visibility. To brighten, turn the control dial upward. To darken, turn the control dial downward.


The HID headlights generate more light than conventional halogen headlights. Therefore a driver of an oncoming vehicle may experience too much glare when your headlight beam height adjustment is high due to the vehicle carrying a heavy load. The headlight beam leveler can be used to adjust beam height to avoid such a condition.


The higher turned to, becomes.


the number


the lower


the switch is the beam height


The parking light switch operates regard- less of the ignition switch position.


By pushing the front end of this switch, following lights will come on. – Parking lights – Front side marker lights – Tail lights – License plate lights


To turn off, push the rear end of parking light switch. Avoid leaving these lights on for a long time because that will run down the battery.


the


北米Model "A8130BE-B" EDITED: 2007/ 7/ 25


3-24 Instruments and controls


Front fog light button


Wiper and washer


The front fog lights operate only when the headlights are on low beam. Push the front fog light button to turn the front fog lights on. However, the front fog lights turn off when the headlights are switched to high beam. Press the button again to turn them off. The indicator light located on the button will illuminate when the front fog lights are on.


WARNING


In freezing weather, do not use the windshield washer until the wind- shield is sufficiently warmed by the defroster. Otherwise the washer fluid can freeze on the windshield, blocking your view.


CAUTION


. Do not operate the washer con- tinuously for more than 10 sec- onds, or when the washer fluid tank is empty. This may cause overheating of the washer motor. Check the washer fluid level frequently, such as at fuel stops. . Do not operate the wipers when the windshield or rear window is dry. This may scratch the glass, damage the wiper blades and cause the wiper motor to burn out. Before operating the wiper on a dry windshield or rear window, always use the wind- shield washer.


Black plate (138,1)


. In freezing weather, be sure that the wiper blades are not frozen to the windshield or rear window before switching on the wipers. Attempting to operate the wiper with the blades frozen to the window glass could cause not only the wiper blades to be damaged but also the wiper mo- tor to burn out. the wiper blades are frozen to the window glass, be sure to operate the defroster, windshield wiper dei- cer (if equipped) or rear window defogger before turning on the wiper.


If


. If the wipers stop during opera- tion because of ice or some other obstruction on the window, the wiper motor could burn out even if the wiper switch is turned off. If this occurs, promptly stop the vehicle in a safe place, turn the ignition switch to the “LOCK” position and clean the window glass to allow proper wiper op- eration.


. Use clean water if windshield washer fluid is unavailable. In areas where water freezes in winter, use SUBARU Windshield Washer Fluid or the equivalent.


北米Model "A8130BE-B" EDITED: 2007/ 7/ 25


face of the windshield or rear window and the wiper blades using a sponge or soft cloth with a neutral detergent or mild abrasive cleaner. After cleaning, rinse the window glass and wiper blades with clean water. The glass is clean if no beads form on the glass when you rinse with water. . If you cannot eliminate the streaking even after following this procedure, replace the wiper blades with new ones. Refer to the “Replacement of wiper blades” section (chapter 11) for replacement instructions.


(See the “Windshield washer fluid” section in chapter 11.) Also, when driving the vehicle when there are freezing tempera- tures, use non-freezing type wi- per blades.


. Do not clean the wiper blades with gasoline or a solvent, such as paint thinner or benzene. This will cause deterioration of the wiper blades.


NOTE . The wiper operates only when the ignition switch is in the “ON” or “Acc” position. . Clean your wiper blades and win- dow glass periodically with a washer solution to prevent streaking, and to remove accumulations of road salt or road film. Keep the washer button depressed at least for 1 second so that washer solution will be sprinkled all over the windshield or rear window. . Grease, wax, insects or other mate- rial on the windshield or the wiper blade results in jerky wiper operation and streaking on the glass. If you cannot remove those streaks after operating the washer or if the wiper operation is jerky, clean the outer sur-


Black plate (139,1)


Instruments and controls 3-25


& Windshield wiper and washer


switches


! Windshield wipers


OFF: Park


: Intermittent LO: Low speed HI: High speed


To turn the wipers on, push the wiper control lever down. To turn the wipers off, return the lever to the “OFF” position.


– CONTINUED –


北米Model "A8130BE-B" EDITED: 2007/ 7/ 25


3-26 Instruments and controls


! Wiper intermittent time control (if


equipped)


! Mist (for a single wipe)


For a single wipe of the wipers, pull the lever toward you. The wipers operate until you release the lever. ! Washer


When the wiper switch is in the “ ” position, turn the dial to adjust the operat- ing interval of the wiper.


The operating interval can be adjusted continuously from the shortest interval to the longest. Two click stop positions of the dial may help you to aim at your desired interval.


Black plate (140,1)


To wash the windshield, push the washer button at the end of the wiper control lever. The washer fluid sprays until you release the washer button. The wipers operate while you push the button.


& Rear window wiper and


washer switch


: Washer (accompanied by wiper operation)


ON: Normal INT: Intermittent OFF: Park : Washer


! Rear wiper To turn the rear wiper on, turn the knob on the end of the wiper control lever upward.


INT: Intermittent


北米Model "A8130BE-B" EDITED: 2007/ 7/ 25


Windshield wiper deicer (if equipped)


CAUTION


To prevent the battery from being discharged, do not operate the windshield wiper deicer continu- ously for any longer than necessary.


ON: Normal


the wiper control


To turn the wiper off, return the knob on the end of the lever to the “OFF” position. ! Washer To wash the rear window while the rear wiper is operating, turn the knob on the end of lever counter- clockwise to the “ ” position. The washer fluid sprays until you release the knob. To wash the rear window when the rear wiper is not in use, turn the knob on the end of the wiper control lever clockwise to the “ ” position. The washer fluid sprays and the wiper operates until you release the knob.


Black plate (141,1)


Instruments and controls 3-27


windshield wiper deicer is operating. The windshield wiper deicer will automa- tically shut off after approximately 15
minutes. If the wiper blades have been deiced completely before that time, push the button to turn it off. It also turns off when the ignition switch is turned to the “Acc” or “LOCK” position. If deicing is not complete, you have to push the button to turn the deicer on again. NOTE If your vehicle is equipped with the outside mirror defogger, the outside mirror defogger operates while the windshield wiper deicer is operating.


The windshield wiper deicer operates only when the ignition switch is in the “ON” position. Before turning on the windshield wiper deicer, remove any snow from the wind- shield. To turn on the windshield wiper deicer, push the button. The indicator light located on the button lights up while the


北米Model "A8130BE-B" EDITED: 2007/ 7/ 25


3-28 Instruments and controls


Rear window defogger but- ton


Manual climate control system


Automatic climate control system


The rear window defogger operates only when the ignition switch is in the “ON” position. The rear window defogger button is located on the climate control panel. To turn on the defogger, push the button. To turn it off, push the button again. The indicator light located on the button lights up while the rear window defogger is operating.


If


The defogger will automatically shut off after approximately 15 minutes. the window clears before that time, push the button to turn it off. It also turns off when the ignition switch is turned to the “Acc” or “LOCK” position. If defrosting or defogging is desired when you restart your vehicle, you have to push the button to turn it on again. Turn on the rear window defogger if the wiper is frozen to the glass.


CAUTION


. Do not use sharp instruments or window cleaner containing abra- sives to clean the inner surface of the rear window. They may damage the conductors printed on the window.


. To prevent the battery from being


Black plate (142,1)


discharged, do not operate the defogger continuously for any longer than necessary.


北米Model "A8130BE-B" EDITED: 2007/ 7/ 25


Mirrors


Always check that the inside and outside mirrors are properly adjusted before you start driving.


& Inside mirror


! Auto-dimming mirror/compass (if


equipped)


The inside mirror has a day and night position. Pull the tab at the bottom of the mirror toward you for the night position. Push it away for the day position. The night position reduces glare from head- lights.


Left button


1) 2) Auto dimming indicator 3) Photosensor 4) Right button


The auto-dimming mirror/compass has an anti-glare feature which automatically re- duces glare coming from headlights of vehicles behind you. It also contains a built-in compass. . By pressing and releasing the left button, the automatic dimming function is toggled on or off. When the automatic dimming function is on, the auto dimming indicator light (green) located to the right of the button will illuminate. . By pressing and releasing the right


Black plate (143,1)


Instruments and controls 3-29


button, the compass display is toggled on or off. When the compass is on, an illuminated compass reading will appear in the lower part of the mirror.


Even with the mirror in anti-glare mode, the mirror surface turns bright the transmission is shifted into reverse. This is to ensure good rearward visibility during reversing. ! Photosensors


if


The mirror has a photosensor attached on both the front and back sides. If the glare from the headlights of vehicles behind you strikes the mirror, these sensors detect it and make the reflection surface of the mirror dimmer to help prevent you from being blinded. For this reason, use care not to cover the sensors with stickers, or – CONTINUED –


北米Model "A8130BE-B" EDITED: 2007/ 7/ 25


3-30 Instruments and controls


other similar items. Periodically wipe the sensors clean using a piece of dry soft cotton cloth or an applicator. ! Compass calibration 1. For optimum calibration, switch off all nonessential electrical accessories (rear window defogger, heater/air conditioning system, spotlight, etc.) and ensure all doors are shut. 2. Drive to an open, level area away from large metallic objects or structures and make certain the ignition switch is in the “ON” position. 3. Press and hold the left button for 3
seconds then release, and the compass will enter the calibration mode. “CAL” and direction will be displayed. 4. Drive slowly in a circle until “CAL” disappears from the display (approxi- mately two or three circles). 5. The compass is now calibrated. Further calibration is not required. The compass will automatically calibrate from this point forward.


Black plate (144,1)


! Compass zone adjustment


exit the zone setting mode.


& Outside mirrors


Compass calibration zones


1. The zone setting is factory preset to Zone 8. Refer to the “Compass calibration zone” map shown above or one attached to the end of this manual to verify that the compass zone setting is correct for your geographical location. 2. Press and hold the right button for 3
seconds then release, and the word “ZONE” will briefly appear and then the zone number will be displayed. 3. Press the right-hand button repeatedly to cycle the display through all possible zone settings. Stop cycling when the correct zone setting for your location is displayed. 4. Releasing the button for 3 seconds will


! Convex mirror (passenger side)


WARNING


Objects look smaller in a convex mirror and farther away than when viewed in a flat mirror. Do not use the convex mirror to judge the distance of vehicles behind you when changing lanes. Use the inside mirror (or glance backwards) to determine the actual size and dis- tance of objects that you view in convex mirror.


北米Model "A8130BE-B" EDITED: 2007/ 7/ 25


! Remote control mirror switch


! Outside mirror defogger (if


equipped)


CAUTION


To prevent the battery from being discharged, do not operate the de- fogger continuously for any longer than necessary.


1) Selection switch 2) Direction control switch


The remote control mirrors operate only when the ignition switch is in the “ON” or “Acc” position. 1. Press either end of switch, “L” for the left, “R” for the right. 2. Move the direction control switch in the direction you want to move the mirror. 3. Return the selection switch to the neutral position to prevent unintentional operation.


the selection


The mirrors can also be adjusted manu- ally.


1) Outside mirror defogger button (if


equipped)


2) Outside mirror defogger and windshield


wiper deicer button (if equipped)


The outside mirror defogger operates only when the ignition switch is in the “ON” position. To turn on the outside mirror defogger, push the button. To turn it off, push the


Black plate (145,1)


Instruments and controls 3-31


button again. The indicator light located on the button lights up while the outside mirror defogger is operating.


If


The defogger will automatically shut off after approximately 15 minutes. the mirror clears before that time, push the button to turn it off. It also turns off when the ignition switch is turned to the “Acc” or “LOCK” position. If defrosting or defogging is desired when you restart your vehicle, you have to push the button to turn it on again. NOTE On vehicles equipped with a wind- shield wiper deicer, the windshield wiper deicer switch is also used to operate the outside mirror defogger.


北米Model "A8130BE-B" EDITED: 2007/ 7/ 25


Black plate (146,1)


3-32 Instruments and controls


Tilt steering wheel


5. Make sure that the steering wheel is securely locked by moving it up and down.


Horn


WARNING


Loading...
x