mentary static, flutter or station interfer- ence. If reception continues to be unsatis- factory, switch to a stronger station.
Installation of accessories Always consult your SUBARU dealer be- fore installing a citizen band radio or other transmitting device in your vehicle. Such devices may cause the electronic control system to malfunction if they are incorrect- ly installed or if they are not suited for the vehicle.
5-2 Audio
Antenna system
Audio
500011
The antenna is printed on the inner sur- face of the left side rear quarter window glass.
Do not use sharp instruments or window cleaner containing abra- sives to clean the inner surface of the window on which the antenna is printed. Doing so may damage the antenna printed on the window.
(cid:132) FM reception Although FM is normally static free, recep- tion can be affected by the surrounding ar-
(cid:132) Type B audio set
Audio set Your SUBARU may be equipped with one of the following audio sets. See the pages indicated in this section for operating de- tails.
(cid:132) Type A audio set
Audio 5-3
(cid:132) In-dash 6 CD auto changer
(Optional audio unit – if equipped)
500215
(cid:121) Radio operation: refer to page 5-12
(cid:121) Built-in CD changer operation: refer to
page 5-16
500216
(cid:121) Inserting and removing a disc or all
discs: refer to page 5-19
500214
(cid:121) Radio operation: refer to page 5-4
(cid:121) Compact disc player operation: refer to
page 5-8
(cid:121) CD changer control: refer to page 5-10
5-4 Audio
Type A audio set (if equipped) The radio will operate only when the ignition switch is in the “ACC” or “ON” position.
(cid:132) Radio operation
(1)
(2)
(1) Power switch, Volume control, Tone/
Fader/Balance control dial
(2) BAND button (3) Tuning buttons (4) Preset buttons (5) AUDIO button (6) SCAN button (cid:84) Power switch and volume/bass/tre-
ble/fader/balance control (PWR/ VOL)
The dial (1) is used for both power (ON/
OFF) and volume control. The radio is
turned ON and OFF by pushing the dial
and the volume is controlled by turning the
dial.
(cid:86) Tone and balance control
The “VOLUME” control knob normally
function as volume control. This knob be-
come a control for Treble, Bass, Fader or
Balance when you select the appropriate
audio mode.
Choose desired volume level for each
mode by turning the “VOLUME” control
knob. The control function returns to vol-
ume control mode after approximately 5
seconds.
To change control modes: Each brief
press of the “AUDIO” button changes con-
trol modes in the following sequence start-
ing from volume control mode. (When the
(6)
(5)
(4)
(3)
500217
radio is first turned on, the control mode is in the volume control.)
Volume (VOL)
Bass (BAS)
Fader (FAD)
Treble (TRE) Balance (BAL)
Display
Control mode
Audio 5-5
Turn counterclockwise
Turn clockwise
500009
VOL
BAS
TRE
BAL
FAD
Volume control
For less volume
For less bass sound
For less treble sound
Bass control
Treble control
Balance control
Fader control
For more volume
For more bass sound
For more treble sound
To increase left speaker volume and decrease right speaker volume
To increase right speaker volume and decrease left speaker volume
To increase rear speaker volume and decrease front speaker volume
To increase front speaker volume and decrease rear speaker volume
– CONTINUED –
5-6 Audio
(cid:84) FM/AM/Weather band selection but-
ton (BAND)
Push the “BAND” button when the radio is on to select FM1, FM2, AM or Weather band (WB) reception. Each time this but- ton is pressed, the band will change in the following order:
FM1
FM2
AM
WB
The display indicates which one is cur- rently selected. (cid:84) Stereo indicator The stereo indicator “ST” will come on when an FM stereo broadcast is received. (cid:84) Tuning (TUNE) (cid:86) Manual tuning (TUNE) Push the “ ” side of the tuning button (3) to increase the tuning frequency and press the “ ” side of the button to de- crease it. Each time the button is pressed, the fre- quency changes 10 KHz in the AM wave- band and 0.2 MHz in the FM waveband. (cid:86) Manual tuning for weather band When weather band mode is selected, ” side of the tuning button press the “
(3) to change the WB channel up and press the “ ” side of the tuning button to change the WB channel down. Each time the button is pressed, the WB chan- nel changes to the next channel. (cid:84) Seek tuning If the tuning button (3) is pressed for long- er than half of a second, the radio will be- gin to automatically search for receivable frequencies and will stop at the first one found. This function may not be available, however, when radio signals are weak. In such a situation, perform manual tuning to select the desired station. (cid:84) Automatic tuning (SCAN) Press the “SCAN” button (6) to change the radio to the SCAN mode. In this mode, the radio scans through the radio band until a station is found. The radio will stop at the station for five seconds while displaying the frequency, after which scanning will continue until the entire band has been scanned from the low end to the high end. Press the “SCAN” button again to cancel the SCAN mode and to stop on any dis- played frequency. When the “SCAN” button is pressed for automatic tuning, stations are scanned in the direction of low frequencies to high fre- quencies only. Automatic tuning may not function proper-
ly if the station reception is weakened by
distance from the station or proximity to
tall buildings and hills.
(cid:84) Selecting preset stations
Presetting a station with a preset button
(4) allows you to select that station in a
single operation. Up to six WB, AM, FM1
and FM2 stations each may be preset.
(cid:84) How to preset stations
1. Press the “BAND” selection button to
select AM, FM1, FM2 or WB reception.
2. Press the “SCAN” button (6) or tune
the radio manually until the desired station
frequency is displayed.
3. Press one of the preset buttons (4) for
at least 2 seconds to store the frequency.
At this time, there will momentarily be no
sound from the radio. If the button is
pressed for less than 2 seconds, the pre-
ceding selection will remain in memory.
NOTE
(cid:121) If the connection between the radio
and battery is broken for any reason
such as vehicle maintenance or radio
removal, all stations stored in the pre-
set buttons are cleared. If this occurs,
it is necessary to reset the preset but-
tons.
(cid:121) If a cell phone is placed near the ra-
dio, it may cause the radio to emit
noise when it receives calls. This noise does not indicate a radio fault.
Audio 5-7
– CONTINUED –
5-8 Audio
(cid:132) Compact disc player operation
(15)
(7)
(8)
(9)
(14)
(13)
(12)
(11)
(10)
500218
(7) Disc slot
(8) CD button
(9) Eject button
(10) Fast-forwarding and track up button
(11) Fast-reversing and track down button
(12) Random button
(13) Repeat button
(14) Scan button
(15) PWR (power) switch
(cid:84) To play back a compact disc
(cid:86) When CD is not in the player
Hold a disc with a finger in the center hole
while gripping the edge of the disc, then
insert it in to the slot (with the label side
up) and the player will automatically pull
the disc into position.
A single CD (8 cm/3 inch CD) may also be
used without any adapter.
NOTE
(cid:121) Make sure to always insert a disc
with the label side up. If a disc is insert-
ed with the label side down, it might be
ejected or the player might shut off.
(cid:121) After the last song finishes, the play-
er will automatically return to track 1
(the first song on the disc).
(cid:86) When CD is in the player
Press the “CD” button (8). The display will
show “CD-IN” and the player will start playback. NOTE After the last song finishes, playback will automatically return to track 1 (the first song on the disc). (cid:84) To stop playback of a CD When the “PWR” button (15) is pressed during playback of a CD, the CD stops playing temporarily. To let the CD resume playing, press the button again. (cid:84) To select a song from its beginning (cid:86) Forward direction Briefly press the “ ” side of the button (10) to skip to the beginning of the next track. Each time this side of the button is pressed, the indicated track number will increase. (cid:86) Backward direction Briefly press the “ ” side of the button (11) to skip to the beginning of the current track. Each time this side of the button is pressed, the indicated track number will decrease. (cid:84) Fast-forwarding and fast-reversing (cid:86) Fast-forwarding Press the “
” side of the button (10)
” side of the button (11)
continuously to fast-forward the disc. Release the button to stop fast-forward- ing. (cid:86) Fast-reversing Press the “ continuously to fast-reverse the disc. Release the button to stop fast-reversing. (cid:84) Repeat playback Briefly press the “RPT” button (13) while a song is playing to play the song repeated- ly. The “RPT” indicator will come on and the song will be played continuously. To cancel the repeat mode, press the button again. Then the “RPT” indicator goes out, and normal playback mode is restored. (cid:84) Random playback Briefly press the “RAND” button (12) while a disc is being played back to play all songs on the disc in a random order. The “RAND” indicator will come on and all songs on the disc will be played in a ran- dom order. To cancel the random mode, press the button again. Then the “RAND” indicator goes out, and normal playback mode is restored. (cid:84) Scan Briefly press the “SCAN” button (14), and you can hear the first 10 seconds of each
Audio 5-9
track to search for the desired program. To continue listening to the program, press the “SCAN” button again. After all tracks on the disc has been scanned, nor- mal playback mode is restored. (cid:84) To eject a disc from the player When a disc is being played back or when a disc is in the player, press the eject but- ton “ The disc may be removed even when the ignition switch is in the “LOCK” position. NOTE Avoid driving the vehicle with a CD sticking out, because vibration might make it fall out.
” (9). The disc will be ejected.
– CONTINUED –
5-10 Audio
(cid:132) CD changer control (if optional in-dash CD changer is connect-
ed)
An optional CD changer can be connected to this audio unit. Consult the instructions that accompany the CD changer for operating the CD changer itself (e.g., how to load or un- load CDs). See your SUBARU dealer for more information.
(16)
(20)
(19)
(18)
(17)
500219
(16) CD button
(17) Track selection buttons
(18) RAND (Random) button
(19) RPT (Repeat) button
(20) SCAN button
(cid:84) To start playback
When the “CD” button (16) is pressed, the
CD changer will start playback. The dis-
play shows the current disc number, track
number and the elapsed time during play-
back.
NOTE
(cid:121) If a disc is in the player, the “DISC”
button is used to change from CD play-
er operation to DISC changer opera-
tion. Each time the “DISC” button is
pressed,
the operating mode will
change alternately.
(cid:121) At the end of the disc, the player au-
tomatically continues with the next
disc.
(cid:121) After playback on the last disc finish-
es, playback will automatically return
to the first disc.
(cid:121) If you have loaded fewer than 6
discs, any missing disc is automatical-
ly skipped.
(cid:84) Selection of a desired disc
You can select a desired disc from among
the discs contained in the CD changer only by pressing the corresponding num- ber on one of the disc select buttons. If you are to listen to the 5th disc in the CD changer, press the “5” button of the disc select buttons. All other discs in the CD changer can also be selected in a similar way. NOTE (cid:121) No disc change takes place if the button corresponding to the storage tray in which no disc is loaded is pressed. (cid:121) If the disc select button correspond- ing to the disc now in playback is pressed again, the disc will be replayed from its beginning. (cid:84) To select a song from its beginning (cid:86) Forward direction Briefly press the “ ” side of the button (17) to skip to the beginning of the next track. Each time this side of the button is pressed, the indicated track number will increase. (cid:86) Backward direction Briefly press the “ ” side of the button (17) to skip to the beginning of the current track. Each time this side of the button is pressed, the indicated track number will
” side of the button (17)
decrease. (cid:84) Fast-forwarding and fast-reversing (cid:86) Fast-forwarding Press the “ continuously to fast-forward the disc. Release the button to stop fast-forward- ing. If you continue fast-forwarding to the end of the disc, the CD changer will automati- cally stop fast-forwarding and start play- back beginning with the first track on the current disc. (cid:86) Fast-reversing Press the “ continuously to fast-reverse the disc. Release the button to stop fast-reversing. If you continue fast-reversing to the begin- ning of the disc, the CD changer will auto- matically stop fast-reversing and start playback beginning with the first track on the current disc. (cid:84) Repeat playback Press the “RPT” button (19) while a song is playing to play the song repeatedly. The “RPT” indicator will come on and the song will be played continuously. To cancel the repeat mode, press the button again. Then the “RPT” indicator goes out, and normal playback mode is restored.
” side of the button (17)
Audio 5-11
(cid:84) Random playback Press the “RAND” button (18) while a disc is being played back to play all songs on the disc in a random order. The “RAND” indicator will come on and all songs on the disc will be played in a random order. To cancel the random mode, press the button again. Then the “RAND” indicator goes out, and normal playback mode is restored. (cid:84) Scan (a convenient way to become
familiar with a disc)
1. Press the “SCAN” button (20).
– The display shows “SCAN” and the track number being scanned. – You hear the first 10 seconds of each track. – The operation is automatically cleared after playing all programs. Then, normal playback starts.
2. Press the “SCAN” button again when you hear a track you like.
– Normal playback resumes.
(cid:84) To stop playback To stop playback and switch over to the radio mode, press the “BAND” button.
5-12 Audio
Type B audio set (if equipped) The radio will operate only when the ignition switch is in the “ACC” or “ON” position.
(cid:132) Radio operation
(1) (2) (3)
(4)
(5)
(6)
(1) SCAN button (2) FM/AM selection button (3) WB (weather band) button (4) Power switch, Volume control, Bass/ Midrange/Treble control and Fader/ Balance control dial
(5) TONE button (6) Fader/Balance selection button (7) Preset buttons (8) Tuning buttons (cid:84) Power switch and volume/bass/tre-
ble/fader/balance control (PWR/ VOL)
The dial (4) is used for both power (ON/ OFF) and volume control. The radio is turned ON and OFF by pushing the dial and the volume is controlled by turning the dial. This dial is used for bass/midrange/treble controls when the “TONE” button (5) is in the depressed position. It is also used for fader/balance controls when the “BAL” button (6) is in the depressed position.
(8)
(7)
500220
Display
Control mode
Audio 5-13
Turn counterclockwise
Turn clockwise
500009
BASS
MIDDLE
TREBLE
FADER
Bass control
For less bass sound
Midrange control
For less midrange sound
For less treble sound
Treble control
Fader control
For more bass sound
For more midrange sound
For more treble sound
To increase rear speaker volume and decrease front speaker volume
To increase front speaker volume and decrease rear speaker volume
BALANCE
Balance control
To increase left speaker volume and decrease right speaker volume
To increase right speaker volume and decrease left speaker volume
VOLUME
Volume control
For less volume
For more volume
(cid:86) Tone control The volume control dial (4) normally func- tion as volume control. The dial become a control for Bass, Midrange or Treble when
you select the appropriate tone control mode. Choose desired setting for each mode by turning the volume control dial. The con- trol function returns to volume control
mode after approximately 5 seconds. To change control modes: Each brief press of the “TONE” button (5) changes control modes in the following sequence
– CONTINUED –
5-14 Audio
starting from bass control mode. (When the radio is first turned on, the control mode is in the volume control.)
BASS
MIDDLE
TREBLE
VOLUME
(cid:86) Fader and balance control The volume control dial (4) normally func- tion as volume control. The dial become the controls for Fader or Balance when you select the appropriate fader and bal- ance control mode. Choose desired setting for each mode by turning the volume control dial. The con- trol function returns to volume control mode after approximately 5 seconds. To change control modes: Each brief press of the “BAL” button (6) changes control modes in the following sequence starting from fader control mode. (When the radio is turned on, the control mode is in the volume control.)
FADER
BALANCE
VOLUME
(cid:86) Display illumination dimness can-
cellation (BRIGHT)
The brightness of the radio display dims when the light switch is in the “ ” or ” positions. If this makes the display “ difficult to read, press the volume dial for more than 1.5 seconds to return the dis- play to original brightness. Subsequently pressing the volume dial again for more than 1.5 seconds or if you can safely do so, turning the light switch to the OFF position and back to the “ ” or“ ” position makes the radio display dim again. (cid:84) FM/AM selection button (FM/AM) Push the “FM/AM” button when the radio is on to select FM1, FM2 or AM reception. Each time this button is pressed, the band will change in the following order:
FM1
FM2
AM
The display indicates which one is cur- rently selected. (cid:84) Stereo indicator The stereo indicator “ST” will come on when an FM stereo broadcast is received.
(cid:84) Weather band button (WB) Press the “WB” button when the radio is on to select the weather band. (cid:84) Manual tuning (TUNE) (cid:86) Manual tuning for AM and FM wave-
band
Push the “ ” side of the tuning button (8) to increase the tuning frequency and press the “ ” side of the button to de- crease it. Each time the button is pressed, the fre- quency changes 10 KHz in the AM wave- band and 0.2 MHz in the FM waveband. (cid:86) Manual tuning for weather band When weather band mode is selected, press the “ ” side of the tuning button (8) to change the WB channel up and press the “ ” side of the button to change the WB channel down. Each time the button is pressed, the WB channel changes to the next channel. (cid:84) Seek tuning If the tuning button (8) is pressed for long- er than half of a second, the radio will be- gin to automatically search for receivable frequencies and will stop at the first one found. This function may not be available, however, when radio signals are weak. In such a situation, perform manual tuning to
OR
Press the “WB” button (3) to select the weather band.
2. Press the “SCAN” button (1) or tune the radio manually until the desired station frequency is displayed. 3. Press one of the preset buttons (7) for at least 1.5 seconds to store the frequen- cy. The frequency of the station will flash once on the display at this time. NOTE (cid:121) If the connection between the radio and battery is broken for any reason such as vehicle maintenance or radio removal, all stations stored in the pre- set buttons are cleared. If this occurs, it is necessary to reset the preset but- tons. (cid:121) If a cell phone is placed near the ra- dio, it may cause the radio to emit noise when it receives calls. This noise does not indicate a radio fault.
select the desired station.
(cid:84) Automatic tuning (SCAN)
Press the “SCAN” button (1) to change the
radio to the SCAN mode. In this mode, the
radio scans through the radio band until a
station is found. The radio will stop at the
station for five seconds while displaying
the frequency, after which scanning will
continue until the entire band has been
scanned from the low end to the high end.
Press the “SCAN” button again to cancel
the SCAN mode and to stop on any dis-
played frequency.
When the “SCAN” button is pressed for
automatic tuning, stations are scanned in
the direction of low frequencies to high fre-
quencies only.
Automatic tuning may not function proper-
ly if the station reception is weakened by
distance from the station or proximity to
tall buildings and hills.
(cid:84) Selecting preset stations
Presetting a station with a preset button
(7) allows you to select that station in a
single operation. Up to six AM, FM1, FM2
and WB stations each may be preset.
(cid:84) How to preset stations
1. Press the “FM/AM” selection button to
select AM, FM1 or FM2 reception.
Audio 5-15
– CONTINUED –
5-16 Audio
(cid:132) Built-in CD changer operation
(9)
(10)
(11)
(12)
(13)
(14)
(15)
(16)
(18)
(17)
500221
(9) Eject button (10) SCAN button (11) CD (CD player selection) button (12) Disc slot (13) DISC indicator (14) Repeat button (15) Random button (16) LOAD button (17) Disc select buttons (18) Track selection buttons NOTE (cid:121) Make sure to always insert a disc with the label side up. If a disc is insert- ed with the label side down, it might be ejected or the player might shut off. (cid:121) Single CDs (i.e., 8 cm/3 inch CDs) are not supported, and if inserted, they will be immediately ejected. (cid:121) If a disc is inserted during a radio broadcast, the disc will interrupt the broadcast. (cid:84) How to insert a CD(s) (cid:86) Inserting a CD 1. Press “LOAD” button (16). If the maga- zine in the player has an idle position where you can insert a disc, the “DISC” in- dicator (13) associated with the idle posi- tion will blink. If no indicator blinks, it means that there is
no idle position in the magazine. 2. As soon as the “DISC” indicator (13) begins to blink, the “LOAD” will blink on display for a period of 15 seconds. Insert a disc during the period. The disc will be then automatically drawn in, and the play- er will begin to play back the first track of the disc. (cid:121) To insert more discs in succession, re- peat Steps 1 and 2. The magazine will be loaded with discs in the ascending order of position number. If you do not insert any disc in 15 seconds after you have pressed the “LOAD” but- ton, the player will begin to play back the first track of the last disc you have insert- ed. (cid:121) The disc indicator steadily lights up if a disc is already inserted in the correspond- ing position of the magazine. (cid:121) While the player is in the loading mode, if you press the “FM/AM” selection button (2), the player will enter the standby mode. Press the “CD” button (11) to start playback. (cid:86) Inserting a disc in a desired position 1. Press the “LOAD” button (16). If the magazine in the player has an idle posi- tion where you can insert a disc, the “DISC” indicator (13) associated with the idle position will blink.
The positions in the magazine the indica- tor of which steadily lights up are already loaded with discs. 2. Press the disc select button (17) at the position where you want to insert a disc. The associated “DISC” indicator will blink, and then the “LOAD” will blink. 3. If you insert a disc during the 15-sec- ond period while the “LOAD” is on display, the disc will be automatically drawn in, and the player will start playback of the disc, beginning with the first track. (cid:121) To insert more discs in succession, re- peat Steps 1 and 2. (cid:121) While the player is in the loading mode, if you press the “FM/AM” selection button (2), the player will enter standby mode. Press the “CD” button (11) to start play- back. (cid:86) Loading all the magazine (Full disc
loading mode)
1. If you continue to press the “LOAD” button (16) for more than 1.5 seconds, the player will produce beep sound and will enter the full disc loading mode. 2. A “DISC” indicator (13) will blink, and the “ALL LOAD” will be on display for a pe- riod of 15 seconds. If a disc is successfully loaded during this period, the “DISC” indi- cator will stop blinking and will steadily light.
Audio 5-17
3. When the loading of a disc is complete,
the next “DISC” indicator will blink. Then
repeat Step 2.
4. When the magazine is filled with discs
by repeating Steps 2 and 3, the player will
start playback of the discs, beginning with
the one inserted first.
If you fail to insert any disc during each 15
seconds interval, the full disc loading
mode will be canceled, and the player will
start playback of the disc inserted first.
(cid:84) How to play back a CD or make a
pause
(cid:86) When there is no CD inserted: Insert a CD by referring to “How to insert a CD(s)”. When a CD is loaded, the player will start playback of the CD, beginning with the first track. (cid:86) When there are CDs loaded: Press a desired one of the disc select but- tons (17) the “DISC” indicator (13) of which steadily lights up. The player will then start playback of the selected CD, beginning with the first track. (cid:84) To select a song from its beginning (cid:86) Forward direction ” side of the button Briefly press the “ (18) to skip to the beginning of the next – CONTINUED –
5-18 Audio
” side of the button (18)
track. Each time the button is pressed, the indicated track number will increase. (cid:86) Backward direction Briefly press the “ ” side of the button (18) to skip to the beginning of the current track. Each time the button is pressed, the indicated track number will decrease. (cid:84) Fast-forwarding and fast-reversing (cid:86) Fast-forwarding Press the “ continuously to fast-forward the disc. Release the button to stop fast-forward- ing. (cid:86) Fast-reversing Press the “ continuously to fast-reverse the disc. Release the button to stop fast-reversing. (cid:84) Repeat playback Press the “RPT” button (14) while a song is playing to play the song repeatedly. The “RPT” indicator will come on and the song will be played continuously. To cancel the repeat mode, press the button again. Then the “RPT” indicator goes out, and normal playback mode is restored. (cid:84) Random playback Press the “RDM” button (15) while a disc is being played back to play all songs on
” side of the button (18)
be ejected. (cid:86) Ejecting all discs from the player
(All disc ejection mode)
1. If you continue to press the eject button (9), the player will produce beep sound and will enter the all disc ejection mode. 2. Remove the disc that has been eject- ed. The other discs loaded will then be ejected one after another. If you do not re- move the ejected disc within 15 seconds, the “All disc ejection mode” will be can- celed. NOTE Avoid driving the vehicle with a CD sticking out, because vibration might make it fall out.
Do not attempt to insert two or more discs into the slot at a time. Doing so can cause mechanical damage to the CD changer.
the disc in a random order. The “RDM” in- dicator will come on and all songs on the disc will be played in a random order. To cancel the random mode, press the button again. Then the “RDM” indicator goes out, and normal playback mode is restored. (cid:84) Scan When the “SCAN” button (10) is pressed while the disc is being played back, you can hear the first 10 seconds of each track to search for the desired program. To con- tinue listening to the program, press the “SCAN” button again. After all tracks on the disc have been scanned, normal play- back mode is restored. (cid:84) How to unload CDs from the player (cid:86) Ejecting a CD from the player Of the discs loaded, you can select and re- move only one disc. 1. Press the disc select button (17) of the disc whose “DISC” indicator (13) is ON. 2. Press the eject button (9). Then the “DISC” indicator associated with the disc you have selected will blink, and the disc will be ejected. To remove more discs in succession, re- peat Steps 1 and 2. If you press the eject button after turning OFF the ignition switch, only one disc will
In-dash 6 CD auto changer (if equipped) (cid:132) Loading and unloading compact discs
(5)
(1)
(2)
Audio 5-19
(1) Disc slot (2) Disc indicators (disc No.1 to 6) (3) Disc select buttons (disc No.1 to 6) (4) Eject button (5) Disc slot indicator
(4)
(3)
500222
– CONTINUED –
5-20 Audio
(cid:121) Do not attempt to insert two or more discs into the slot at a time. Doing so can cause mechanical damage to the CD changer.
(cid:121) Use only music CDs identified by
mark.
(cid:121) Do not use CDs listed in the fol- lowing which could cause dam- age to the CD player. – 3 inch (8 cm) compact disc. – Any disc with a peel-off or seal
on it.
– Bent disc.
– Cleaning disc.
– CD accessory. (E.g., 3 inch (8
cm) disc adapter)
(cid:121) Do not insert or remove any disc when the automatic transmission selector lever is in the park posi- tion; the selector lever in that po- sition can interfere with disc in- sertion or removal, causing scratches on the disc surface (for AT vehicles).
(cid:84) To insert a disc 1. Press one of the disc select buttons (3)
(numbered from 1 to 6) for which the disc
indicator light (2) is “OFF”.
The disc indicator lights are located direct-
ly above the corresponding disc select
buttons.
2. The indicator will begin blinking. The
blinking will last for 15 seconds.
During this period, insert a desired disc,
and the disc will begin to play. (If any disc
is not inserted during this period, the “Disc
slot” (1) door will close. Repeat Step 1.)
Be sure to hold a disc with the label side
(the side where titles are printed) up.
3. To insert another disc, repeat Steps 1
and 2 choosing a different disc select but-
ton.
(cid:84) To insert six discs at a time
1. Press and hold the disc select button
number 1 until all disc indicators begin
blinking (approximately 1.5 seconds).
2. The indicators will blink for 15 seconds.
During this period, insert desired six discs.
3. When all discs are loaded, the first disc
will begin to play. (If no disc is inserted
within this 15 seconds, the entire disc load
sequence will be canceled.)
(cid:84) To remove a disc
1. Press the desired one of the disc select
buttons (3) (numbered from 1 to 6) for
which the disc indicator light is on.
2. Press the eject button (4). The selected
disc will be ejected and the indicator light will begin blinking. 3. To remove another disc, repeat Steps 1 and 2 choosing a different disc select button. (To remove discs when the ignition switch is in the “Lock” position, press the eject button, and the first disc will be ejected. Press the eject button again, and the next disc will be ejected and so on. At this time, the disc select buttons are disabled.) (cid:84) To remove all discs at one time 1. Press and hold the eject button (4) until all “Disc” indicators begin blinking (ap- proximately 1.5 seconds), and the first disc will be ejected. 2. When the disc is removed, the next one will be ejected, and so on. (cid:84) To replace a playing disc with an-
other
Simply press the desired one of disc se- lect buttons (3) (numbered from 1 to 6) or press the disc select button on the radio unit to select the desired disc, and the disc will begin to play. (cid:84) Disc indicators Lit: when the corresponding storage tray is occupied by a disc. Blinking: Disc player is either in loading, eject or changing mode.
OFF: No disc is loaded or the ignition switch is in the “LOCK” position. (cid:86) Open/Closed disc slot indicator When the disc slot is open, the disc indica- tors on both sides of the slot illuminate. (cid:84) Function control Refer to CD changer control operating in- structions described in the “Type A audio set (if equipped)” section.
Precautions to observe when handling a compact disc Use only compact discs (CDs) that have the mark shown in the following illustra- tion.
Audio 5-21
500010
TM
500033
You may also use compact discs (CD-Rs
and CD-RWs) that have the following
marks, but you may not use some discs if
they were produced using writing methods
not compatible with your vehicle’s audio
system.
DualDisc
500253
(cid:121) You cannot use a DualDisc in the CD player. If you insert a DualDisc into the player, the disc may not come out again, possibly causing the player to malfunc- tion. (cid:121) In cold and/or rainy weather, dew can – CONTINUED –
5-22 Audio
form inside the CD player, preventing nor- mal operation. If this happens, eject the CD and wait for the player to dry out. (cid:121) Skipping may occur when the CD player is subjected to severe vibration (for exam- ple, when the vehicle is driven on a rough surface). (cid:121) To remove a disc from the case, press the center of the case and hold both edg- es of the disc. If the disc surface is touched directly, contamination could cause poor tone quality. Do not touch the disc surface. (cid:121) Use a clean disc whenever possible. If there are deposits, wipe the disc surface from the center outward with a dry, soft cloth. Be sure not to use a hard cloth, thin- ner, benzene, alcohol, etc. (cid:121) Do not use any disc that is scratched, deformed, or cracked. Also, do not use any disc that has a non-standard shape (for example, a heart shape). Malfunctions or problems might result. (cid:121) A disc is vulnerable to heat. Never keep it either in places exposed to direct sun- light, near heaters or in vehicles parked in the sun or on hot days.
500034
Interior equipment
Shopping bag hook ............................................ 6-13
Cargo tie-down hooks ........................................ 6-14
Cargo area bars .................................................. 6-14
Under-floor storage compartment .................... 6-14
Interior lights ...................................................... Dome light ............................................................... Cargo area light ..................................................... Map lights ........................................................... Sun visors ........................................................... Vanity mirror ........................................................... Storage compartments ...................................... Glove box ................................................................ Center console ........................................................ Overhead console .................................................. Dashboard storage compartment ......................... Convenience net ..................................................... Cup holders ........................................................ Front passenger’s cup holder ............................... Rear passenger’s cup holder ................................ Accessory power outlets ................................... Cigarette lighter socket ..................................... Use with a cigarette lighter (if equipped) ............. Using as an accessory power outlet .....................
6-2
6-2
6-2
6-3
6-3
6-3
6-4
6-4
6-4
6-6
6-6
6-6
6-7
6-7
6-7
6-8
6-9
6-10
6-10
Ashtray ................................................................ 6-11
Floor mat ............................................................. 6-11
Coat hook ............................................................ 6-12
Cargo area cover (if equipped) ......................... 6-12
6-12
6-13
6-13
6-13
Using the cover ....................................................... To remove the cover .............................................. Stowage of the cover ............................................. To install the cover housing ..................................
6-2 Interior equipment
Interior lights When leaving your vehicle, make sure the light goes out to avoid battery discharge.
Interior equipment
(cid:132) Dome light
about 30 minutes later and then the light is turned off automatically. The light also can be turned on by use of the keyless entry transmitter. See the “Re- mote keyless entry system” section in chapter 2 for detailed information. OFF: The light stays off.
(cid:132) Cargo area light
NOTE If a door or the rear gate is left open, the light flashes and a chime sounds about 30 minutes later and then the light is turned off automatically. The light also can be turned on by use of the keyless entry transmitter. See the “Re- mote keyless entry system” section in chapter 2 for detailed information.
ON DOOR OFF
ON
OFF DOOR
600078
The dome light switch has three positions: ON: The light stays on continuously. DOOR (middle position): The dome light comes on when any of the doors or the rear gate is opened. The light remains on for several seconds and gradually goes out after all doors and the rear gate are closed. NOTE If a door or the rear gate is left open, the light flashes and a chime sounds
600079
The cargo area light switch has three po- sitions: ON: The light stays on continuously. OFF: The light stays off. DOOR: The light comes on only when the rear gate is opened.
Map lights
Sun visors
(cid:132) Vanity mirror
Interior equipment 6-3
600080
600081
To turn on the map light, push the switch. To turn it off, push the switch again. When leaving the vehicle, make sure the light is turned off to avoid battery dis- charge.
To block out glare, swing down the visors. To use the sun visor at a side window, swing it down and move it sideways.
600082
To use the vanity mirror, swing down the sun visor and open the vanity mirror cov- er.
6-4 Interior equipment
Storage compartments
(cid:121) Always keep the storage compart- ment closed while driving to re- duce the risk of injury in the event of sudden stops or an accident.
(cid:121) Do not store spray cans, contain- ers with flammable or corrosive liquids or any other dangerous items in the storage compartment.
(cid:132) Glove box
close it, push the lid firmly upward. To lock the glove box, insert the key and turn it clockwise.
(cid:132) Center console The center console box provides a stor- age space. In addition, the top of the con- sole can be used as an armrest and as a rear passenger’s cup holder. To use as armrest:
600471
600519
1. Tip the console top forward from its
vertical position.
1) Lock 2) Unlock
To open the glove box, pull the handle. To
600473
2. Push the armrest part of the console
top forward to the desired position while
pulling up the knob at the front end of the
armrest and lock it in position by releasing
the knob. Adjust the position of the arm-
rest to suit your driving position. Make
sure the armrest is securely retained.
When you slide the armrest back to its
original position, pull the knob upward as
you do so.
To return the console top to the vertical
position, pull upward the knob at the front
end of the armrest while raising the con-
sole top until it emits a click.
Do not step or sit on the armrest, and do not place heavy objects on it. The armrest could break, and you could get hurt. To use as rear passenger’s cup holder:
600520
With the console top tipped toward the
rear seat, it can be used as a cup holder.
(cid:121) To switch from using the console top as an armrest to using it as a rear passenger’s cup holder, raise the console top to the vertical po- sition before tipping it toward the rear seat. Otherwise the console top may break.
(cid:121) Do not place any object weighing more than 4.4 lbs (2 kg) on the ta- ble.
(cid:121) Do not have hot drinks or other objects on the table while driving. During hard braking or negotia- tion of a curve, they could fall from the table and cause a burn or other injury.
Interior equipment 6-5
To use as storage space:
600475
Raise the console top to the vertical posi-
tion or tip it toward the rear seat. Then, pull
up the lock button of the console box and
open the lid.
When closed, the lid can be used as a tray
for placing small items in it.
(cid:121) Before opening the lid of the con- sole box, raise the console top completely to the vertical position or tip it toward the rear seat. Oth- erwise, the lid may be damaged and an injury may occur.
– CONTINUED –
6-6 Interior equipment
(cid:121) Be careful not to trap your hands between the console top and con- sole box when raising and tipping the console top.
(cid:121) When there is an object on the console box lid, do not tip the con- sole top forward. Otherwise, the console top or lid could be dam- aged, and an injury could occur.
(cid:132) Overhead console
When your vehicle is in the sun or on a warm day, the inside of the overhead console heats up. Avoid storing plastic or other heat-vulner- able or flammable articles such as a lighter in the overhead console.
When your vehicle is in the sun or on a warm day, the inside of the overhead console heats up. Avoid storing plastic or other heat-vulner- able or flammable articles such as a lighter in the overhead console.
(cid:132) Dashboard storage compart-
ment
(cid:132) Convenience net
600085
To open the console, push on the console
lid lightly and the lid will automatically
open.
600086
To open the dashboard compartment,
push the button on the lid and the lid will
automatically open. Be sure to close the
compartment fully before driving.
600087
A net for storing small articles is provided
at the front passenger’s foot-well.
Cup holders
(cid:132) Front passenger’s cup holder
Interior equipment 6-7
(cid:121) When not in use, always keep the cup holder stored while driving to reduce the risk of injury in the event of a sudden stop or an acci- dent.
(cid:121) Do not pick up a cup from the cup holder or put a cup in the holder while you are driving, as this may distract you and lead to an acci- dent.
(cid:121) Take care to avoid spills. Bever- ages, if hot, might burn you or your passengers. Spilled bever- ages may also damage upholstery or carpets.
600476
A dual cup holder is built in the center con-
sole, beside the parking brake lever.
(cid:132) Rear passenger’s cup holder There are rear passenger’s cup holders at the back of the center console as well as on the reverse side of the console top. To use rear passenger’s cup holder at back of center console:
600092
To use the cup holder, open the lid by pull- ing its upper edge. To use rear passengers’ cup holder on the reverse side of console top: For the method of use, refer to “Center console” in the “Storage compartments” part of this chapter.
6-8 Interior equipment
Accessory power outlets
Power outlet in cargo area
600094
Power outlet on center console
600477
Accessory power outlets are provided in the center console and in the cargo area. Electrical power (12V DC) from the battery is available at any of outlets when the igni- tion switch is either in the “ACC” or “ON” position. You can use an in-car use electrical appli- ance by connecting it to an outlet. When both outlets are used at the same time, the total power consumption of the electric appliances must be 120W or less.
(cid:121) Do not attempt to use a cigarette lighter in the accessory power outlet.
(cid:121) Do not place any foreign objects, especially metal ones such as coins or aluminum foil, into the accessory power outlet. That could cause a short circuit. Al- ways put the cap on the accesso- ry power outlet when it is not in use.
(cid:121) Use only electrical appliances which are designed for 12V DC and which consume less than 120W. Overloading the accessory power outlet can cause a short circuit. Do not use double adapt- ers or more than one electrical ap- pliance.
(cid:121) If the plug on your electric appli- ance is either too loose or too tight for the accessory power out- let, this can result in a poor con- tact or cause the plug to get stuck. Only use plugs that fit properly.
(cid:121) Use of an electric appliance in the accessory power outlet for a long period of time while the engine is not running can cause battery dis- charge.
(cid:121) Before driving your vehicle, make sure that the plug and the cord on your electrical appliance will not interfere with your shifting gears and operating the accelerator and brake pedals. If they do, do not use the electrical appliance while driving.
Cigarette lighter socket
600478
NOTE When the lid of the center console is closed, an opening remains between the center console and the lid to allow the power outlet in the center console to be used. Pass the electrical appli- ance’s cord through this opening.
600479
A cigarette lighter socket can be found be-
hind the ashtray lid under the climate con-
trols. Push gently on the lid to open it. A
cigarette lighter plug is an optional acces-
sory. It is available from your SUBARU
dealer.
The cigarette lighter socket may also be
used as a power source for an in-car use
electrical appliance.
Interior equipment 6-9
(cid:121) The electrical power socket locat- ed on the lower part of the instru- ment panel is originally designed to use a genuine SUBARU ciga- rette lighter plug. Do not use non- genuine cigarette lighter plugs in the socket. Doing so may cause a short-circuit and overheating, re- sulting in a fire.
(cid:121) If the socket is ever used for a plug-in accessory such as a cell phone, that may damage the por- tion of the socket’s internal mech- anism that causes a cigarette lighter plug to “pop out” after its lighter element is heated. There- fore, do not place a cigarette light- er plug in a socket that has been used, even once, to power a plug- in accessory. Doing so may cause the plug to stick and overheat, creating a potential fire hazard.
(cid:121) Do not place any foreign objects, especially metal ones such as coins or aluminum foil, into the socket. That could cause a short circuit.
– CONTINUED –
6-10 Interior equipment
(cid:132) Use with a cigarette lighter (if
equipped)
600095
The cigarette lighter operates only when
the ignition switch is in the “ON” and
“ACC” positions.
To use the cigarette lighter, push in the
knob and wait a few moments. It will auto-
matically spring up when ready for use.
To avoid being burned, never grasp the lighter by the end with the heat- ing element. Doing so could result in injury and could also damage the heating element.
Do not hold the lighter pushed in, because it will overheat.
(cid:132) Using as an accessory power
outlet
Electrical power (12V DC) from the battery is available at the socket when the ignition switch is either in the “ACC” or “ON” posi- tion. If you use the socket as an accessory power outlet, take the following precau- tions. When the socket is not in use, always put the cap on the socket to prevent any for- eign object from entering it.
(cid:121) Use only in-car use electrical ap- pliances which are designed for 12V DC and which consume less than 120W. Overloading the sock- et can cause a short circuit. Do not use double adapters or more than one electrical appliance.
(cid:121) If the plug on your electric appli- ance is either too loose or too tight for the socket, this can result in a poor contact or cause the plug to get stuck. Only use plugs that fit properly.
(cid:121) Use of an electric appliance in the socket for a long period of time while the engine is not running can cause battery discharge.
(cid:121) Before driving your vehicle, make sure that the plug and the cord on your electrical appliance will not interfere with your shifting gears and operating the accelerator and brake pedals. If they do, do not use the electrical appliance while driving.
If the socket has been used for electrical appliances, damage may have been done to the internal mechanism that causes a cigarette lighter to “pop out” after its ele- ment has been heated. For that reason, a cigarette lighter, even if it is a genuine part, should not be used in the socket. If you want to use the socket for a cigarette lighter again, or to protect your purchaser before you sell your vehicle, have your SUBARU dealer replace the socket with a new one.
Ashtray
NOTE
Floor mat
Interior equipment 6-11
600096
To open the ashtray, push lightly on the lid below the climate controls. Fully close the lid after using it to help re- duce residual smoke. To remove the ashtray for cleaning, hold the right and left sides of the ashtray and pull it out.
600097
Particles of ash and tobacco will accu-
mulate around the hinges of the ash-
tray’s inner lid. Clean them off using a
toothbrush or other narrow-ended im-
plement.
Do not use ashtrays as waste recep- tacles or leave a lighted cigarette in an ashtray. This could cause a fire.
600480
A retaining pin is located on the driver’s
side of the vehicle next to the fuel filler
door release.
The floor mat is secured using the built-in
grommet, by placing the grommet over the
pin and pushing downward.
– CONTINUED –
6-12 Interior equipment
Coat hook
600481
Make sure the driver’s floor mat is placed back in its proper location and correctly secured on its retain- ing pin. If the floor mat slips forward and interferes with the movement of the pedals during driving, it could cause an accident.
600098
The coat hook is attached to the rear left
passenger’s hand grip.
Never hang anything on the coat hook that might obstruct the driv- er’s view or that could cause injury in sudden stops or in a collision. And do not hang items on the coat hook that weigh 2.2 lbs (1 kg) or more.
Cargo area cover (if equipped) The cargo area cover is provided for cov- ering the cargo area and to protect its con- tents from direct sunlight. This cover is de- tachable to make room for additional car- go.
(cid:132) Using the cover
600099
To extend the cover, pull the end of the cover out of the housing, then insert its hooks into the catches as shown. To re- wind it, unhook it from the catches and it will rewind automatically. You should hold on to the cover and guide it back into the cover housing while it is rewinding.
(cid:132) Stowage of the cover
Interior equipment 6-13
Shopping bag hook In the cargo area, there are two retract- able shopping bag hooks (one on each side) and four non-retractable shopping bag hooks (two on each side).
600101
On models having a temporary spare tire,
the cargo area cover can be stowed in un-
der the cargo floor.
(cid:132) To install the cover housing To install the cover, insert both ends of the cover housing into the retainers.
To use either of the retractable hooks, pull the lower portion out.
600492
Do not hang items on the shopping bag hook that weigh 6.6 lbs (3 kg) or more.
Do not place anything on the ex- tended cover. Putting excessive weight on the extended cover can break it and an object on the cover could tumble forward in the event of a sudden stop or collision. This could cause serious injury.
(cid:132) To remove the cover
600100
1. Rewind the cover. 2. Take it off the retainer, lift it out. 3. Store the cover housing in the cargo area.
6-14 Interior equipment
Cargo tie-down hooks
Cargo area bars
Under-floor storage compart- ment
600103
The cargo area is equipped with four tie-
down hooks so that cargo can be secured
with a cargo net or ropes.
When using the hooks, raise them. When
not in use, lower the hooks.
The cargo tie-down hooks are de-
signed only for securing light cargo.
Never try to secure cargo that ex-
ceeds the capacity of the hooks. The
maximum load capacity is 44 lbs (20
kg) per a hook.
600493
1) Cargo area bar
In the cargo area, there are two bars (one on each side) to which a net can be at- tached.
600482
There are four trays in the storage com-
partment underneath the floor of the cargo
area. They can be used to store small
items.
Do not place objects with a total weight exceeding 6.6 lbs (3 kg) on a net attached to the cargo area bars.
(cid:121) Always keep the lids closed while driving to reduce the risk of injury in the event of sudden stop or an accident.
(cid:121) Do not store spray cans, contain- ers with flammable or corrosive liquids or any other dangerous items in the storage compartment.
(cid:84) Front, left and right side storage compartment
Interior equipment 6-15
(cid:84) Center storage compartment (Stor-
age bucket)
To open the lid, raise the cargo tie-down hooks and pull the tab up. The jack and jack handle are stored in the left side storage compartment.
600105
To open the lid, pull the handle up.
600106
600107
To keep the lid open, hang the hook pro-
vided on the backside of the lid on the rear
– CONTINUED –
6-16 Interior equipment
edge of the roof. Canada-spec. non-turbo models: The storage bucket is put on the spare tire. Except Canada-spec. non-turbo mod- els: Storage tray is placed on the spare tire.
600108
NOTE When storing a flat tire, put the storage tray in the luggage compartment (Ex- cept Canada-spec. non-turbo models).
Starting and operating
Steps to take if EBD system fails ..........................
7-18
Vehicle Dynamics Control system
(if equipped) ..................................................... 7-19
Vehicle Dynamics Control system monitor ..........
7-21
7-23
Vehicle Dynamics Control OFF switch .................
Parking your vehicle .......................................... 7-24
7-24
7-24
Parking brake .......................................................... Parking tips .............................................................
Hill holder (Manual transmission –
if equipped) ...................................................... 7-25
Cruise control ..................................................... 7-26
7-26
7-27
7-27
7-28
Self-leveling rear suspension (if equipped) ..... 7-29
To set cruise control .............................................. To temporarily cancel the cruise control ............. To turn off the cruise control ................................. To change the cruising speed ...............................
Fuel ...................................................................... Fuel requirements .................................................. Fuel filler lid and cap .............................................. State emission testing (U.S. only) .................... Preparing to drive .............................................. Starting the engine ............................................. Manual transmission vehicle ................................. Automatic transmission vehicle ............................ Stopping the engine ........................................... Manual transmission ......................................... Shifting speeds ....................................................... Driving tips ..............................................................
7-2
7-2
7-3
7-5
7-6
7-7
7-7
7-7
7-8
7-9
7-9
7-10
Automatic transmission .................................... 7-10
7-11
7-14
Selector lever for automatic transmission ........... Shift lock release .................................................... Rear viscous limited slip differential (LSD) (if
equipped) ......................................................... 7-14
Power steering ................................................... 7-15
Braking ................................................................ 7-15
7-15
7-15
7-16
ABS (Anti-lock Brake System) .......................... 7-16
7-16
7-17
Braking tips ............................................................. Brake system .......................................................... Disc brake pad wear warning indicators ..............
ABS system self-check .......................................... ABS warning light ...................................................
Electronic Brake Force Distribution (EBD)
system (if equipped) ....................................... 7-18
7-2 Starting and operating
Fuel
Starting and operating
Use of a fuel which is low in quality or use of an inappropriate fuel addi- tive may cause engine damage.
(cid:132) Fuel requirements (cid:84) Non-turbo models The 2.5-liter non-turbo engine is designed to operate using unleaded gasoline with an octane rating of 87 AKI or higher. (cid:84) Turbo models The 2.5-liter turbo engine is designed to operate using premium unleaded gasoline with an octane rating of 91 AKI or higher. If premium unleaded gasoline is not avail- able, regular unleaded gasoline with an octane rating of 87 AKI or higher may be temporarily used. For optimum engine performance and driveability, it is required that you use premium grade unleaded gasoline. NOTE Be sure to use premium unleaded gas- oline of 91 AKI or higher for a 2.5-liter turbo engine model. If other gasoline (lower than 91 AKI) is used, knocking,
reduced output and poor accelerator response will result. (cid:84) Fuel octane rating This octane rating is the average of the Research Octane and Motor Octane num- bers and is commonly referred to as the Anti Knock Index (AKI). Using a gasoline with a lower octane rat- ing can cause persistent and heavy knocking, which can damage the engine. Do not be concerned if your vehicle some- times knocks lightly when you drive up a hill or when you accelerate. See your dealer or a qualified service technician if you use a fuel with the specified octane rating and your vehicle knocks heavily or persistently. (cid:84) Unleaded gasoline The neck of the fuel filler pipe is designed to accept only an unleaded gasoline filler nozzle. Under no circumstances should leaded gasoline be used because it will damage the emission control system and may impair driveability and fuel economy. (cid:84) Gasoline for California-certified LEV Your vehicle was certified to California’s low emission vehicle (LEV) standards as indicated on the underhood tune-up label, it is designed to optimize engine and emission performance with gasoline that
meets the clean burning low-sulfur Califor- nia gasoline specifications. If you live in any other state than California, your vehi- cle will operate on gasoline meeting Fed- eral specifications. Gasoline sold outside California is permitted to have higher sul- fur levels, which may affect the perfor- mance of your vehicle’s catalytic convert- er and may produce a sulfur exhaust odor or smell. SUBARU recommends that you try a different brand of unleaded gasoline having lower sulfur to determine if the problem is fuel related before returning your vehicle to an authorized dealer for service. (cid:84) MMT Some gasoline contains an octane-en- hancing additive called MMT (Methylcy- clopentadienyl Manganese Tricarbonyl). If you use such fuels, your emission control system performance may deteriorate and the CHECK ENGINE warning light/Mal- function indicator lamp may turn on. If this happens, to your authorized SUBARU Dealer for service. If it is deter- mined that the condition is caused by the type of fuel used, repairs may not be cov- ered by your warranty. (cid:84) Gasoline for cleaner air Your use of gasoline with detergent addi- tives will help prevent deposits from form-
return
ing in your engine and fuel system. This helps keep your engine in tune and your emission control system working properly, and is a way of doing your part for cleaner air. If you continuously use a high quality fuel with the proper detergent and other additives, you should never need to add any fuel system cleaning agents to your fuel tank. Many gasolines are now blended with ma- terials called oxygenates. Use of these fu- els can also help keep the air cleaner. Ox- ygenated blend fuels, such as MTBE (Me- thyl Tertiary Butyl ether) or ethanol (ethyl or grain alcohol) may be used in your ve- hicle, but should contain no more than 15% MTBE or 10% ethanol for the proper operation of your SUBARU. In addition, some gasoline suppliers are now producing reformulated gasolines, which are designed to reduce vehicle emissions. SUBARU approves the use of reformulated gasoline. If you are not sure what the fuel contains, you should ask your service station oper- ators if their gasolines contain detergents and oxygenates and if they have been re- formulated to reduce vehicle emissions. As additional guidance, only use fuels suited for your vehicle as explained in the
following. (cid:121) Fuel should be unleaded and have an octane rating no lower than that specified in this manual. (cid:121) Methanol (methyl or wood alcohol) is sometimes mixed with unleaded gasoline. Methanol can be used in your vehicle ONLY if it does not exceed 5% of the fuel mixture AND if it is accompanied by suffi- cient quantities of the proper cosolvents and corrosion inhibitors required to pre- vent damage to the fuel system. Do not use fuel containing methanol EXCEPT un- der these conditions. (cid:121) If undesirable driveability problems are experienced and you suspect they may be fuel related, try a different brand of gaso- line before seeking service at your SUBARU dealer. (cid:121) Fuel system damage or driveability problems which result from the use of im- proper fuel are not covered under the SUBARU Limited Warranty.
Do not let fuel spill on the exterior surfaces of the vehicle. Fuels con- taining alcohol may cause paint damage, which is not covered under the SUBARU Limited Warranty.
Starting and operating 7-3
(cid:132) Fuel filler lid and cap (cid:84) Refueling
700029
700030
1. To open the fuel filler lid, pull the lid re-
lease lever. The lever is on the floor at the
left of the driver’s seat.
– CONTINUED –
7-4 Starting and operating
700330
1) Open 2) Close
2. Remove the fuel filler cap by turning it slowly counterclockwise.
(cid:121) Gasoline vapor is highly flamma- ble. Before refueling, always first stop the engine and make sure that there are no lighted ciga- rettes, open flames or electrical sparks in the adjacent area.
(cid:121) When opening the cap, do not re- move the cap quickly. Fuel may be under pressure and spray out of the fuel filler neck especially in hot weather, which may cause in- jury.
3. Stop filling the tank after the fuel filler pump automatically stops. Do not add any more fuel. 4. Put the cap back on, turn it clockwise until you hear a clicking noise. Be certain not to catch the tether under the cap while tightening. 5. Close the fuel filler lid completely. If you spill any fuel on the painted surface, rinse it off immediately. Otherwise, the painted surface could be damaged. NOTE
300121
(cid:121) You will see the “ ” sign in the fuel gauge. This indicates that the fuel filler door (lid) is located on the right side of the vehicle. (cid:121) If the fuel filler cap is not tightened until it clicks or if the tether is caught under the cap, the CHECK ENGINE warning light may come on. Refer to the “Warning and indicator lights” sec- tion located in chapter 3. (Turbo model only) Promptly put fuel in the tank whenever the low fuel warning light comes on. Engine misfires as a re- sult of an empty tank could cause dam- age to the engine.
(cid:121) Never add any cleaning agents to the fuel tank. The addition of a cleaning agent may cause dam- age to the fuel system.
(cid:121) Make sure that the cap is tight- ened until it clicks to prevent fuel spillage in the event of an acci- dent.
(cid:121) Do not let fuel spill on the exterior surfaces of the vehicle. Fuels may cause paint damage, which is not covered under the SUBARU Limit- ed Warranty.
(cid:121) Always use a genuine SUBARU fuel filler cap. If you use the wrong cap, it may not fit or have proper venting, and your fuel tank and emission control system might be damaged.
State emission testing (U.S. only) At state inspection time, remember to tell your inspection or service station in advance not to place your SUBARU AWD vehicle on a two-wheel dyna- mometer. Otherwise, serious transmis- sion damage will result.