Login- Download PDF Manual
-
reprogrammed. Any lost or stolen transmitters will no longer work once the new transmitter is programmed. Each vehicle can have up to eight transmitters programmed to it. See “Relearn Remote Key” under Driver Information Center (DIC) (With DIC Buttons) on page 5‑24 or Driver Information Center (DIC) (Without DIC Buttons) on page 5‑30 for instructions on how to program transmitters to this vehicle.
Battery Replacement Replace the battery if the REPLACE BATTERY IN REMOTE KEY message displays in the DIC. Notice: When replacing the battery, do not touch any of the circuitry on the transmitter. Static from your body could damage the transmitter.
1. Separate the transmitter with a flat, thin object inserted into the notch on the side.
2. Remove the old battery. Do not
use a metal object.
Keys, Doors and Windows
2-5
3.
Insert the new battery, positive side facing down. Replace with a CR2032 or equivalent battery.
4. Snap the transmitter back
together.
Remote Vehicle Start This vehicle may have a remote starting feature that starts the engine from outside of the vehicle. / (Remote Start): This button is located on the RKE transmitter if the vehicle has remote start. Laws in some communities may restrict the use of remote starters. For example, some laws may require a person using the remote start to have the vehicle in view when doing so. Check local regulations for any requirements on remote starting of vehicles. Do not use the remote start feature if the vehicle is low on fuel. The vehicle could run out of fuel.
If the vehicle has the remote start feature, the RKE transmitter functions have an increased range of operation. However, the range may be less while the vehicle is running. There are other conditions which can affect the performance of the transmitter, see Remote Keyless Entry (RKE) System on page 2‑2
for additional information. Starting the Engine Using Remote Start To start the vehicle: 1. Aim the RKE transmitter at thevehicle.
2. Press Q on the RKE transmitter. 3.
Immediately after completing Step 2, press and hold / until the parking lamps flash. If the vehicle's lights can not be seen, press and hold / for at least four seconds.
When the vehicle starts the parking lamps will turn on and remain on as long as the engine is running. The doors will be locked and the climate control system will operate automatically if the vehicle has the automatic system, or at the same setting as when the vehicle was last turned off. If the vehicle has an automatic climate control system and heated seats, the heated seats turn on during colder outside temperatures and shut off when the key is turned to ON/RUN. See Heated Front Seats on page 3‑8 for more information. The rear window defogger and heated mirrors, if the vehicle has them, turn on during colder outside temperatures and turn off when the key is turned to ON/RUN. After entering the vehicle during a remote start, insert and turn the key to the ON/RUN position to drive the vehicle.
2-6
Keys, Doors and Windows
If the vehicle is left running it automatically shuts off after 10 minutes unless a time extension has been done. Extending Engine Run Time To extend the engine run time by 10 minutes, repeat Steps 1 though 3
while the engine is still running. The engine run time can only be extended if it is the first remote start since the vehicle has been driven. Remote start can be extended one time. If the remote start procedure is used again before the first 10 minute time frame has ended, the first 10 minutes will immediately expire and the second 10 minute time frame will start. For example, if the lock button and then the remote start buttons are pressed again after the vehicle has been running for five minutes, 10 minutes are added, allowing the engine to run for a total of 15 minutes.A maximum of two remote starts or remote start attempts are allowed between ignition cycles. After the vehicle's engine has been started two times using the remote start button, the ignition must be turned on and then back off before the remote start procedure can be used again. Shutting the Engine Off After a Remote Start To manually shut off a remote start: . Aim the RKE transmitter at the vehicle and press / until the parking lamps turn off. Turn on the hazard warning flashers. Turn the ignition switch on and then off.
Conditions in Which the Remote Start Will Not Work The vehicle cannot be started using the remote start feature if the key is in the ignition, the hood is open, or if there is an emission control system malfunction. The engine turns off during a remote start if the coolant temperature gets too high or if the oil pressure gets low. Vehicles that have the remote vehicle start feature are shipped from the factory with the remote vehicle start system enabled. The system may be enabled or disabled through the DIC if the vehicle has DIC buttons. See “REMOTE START” under Vehicle Personalization (With DIC Buttons) on page 5‑42 for additional information. If the vehicle does not have DIC buttons, see your dealer/ retailer to enable or disable the remote start system.
Keys, Doors and Windows
2-7
Door Locks
{ WARNING Unlocked doors can be dangerous.
. Passengers, especially
children, can easily open the doors and fall out of a moving vehicle. When a door is locked, the handle will not open it. The chance of being thrown out of the vehicle in a crash is increased if the doors are not locked. So, all passengers should wear safety belts properly and the doors should be locked whenever the vehicle is driven.
. Young children who get into
unlocked vehicles may be unable to get out. A child can be overcome by extreme heat and can suffer permanent
(Continued)
WARNING (Continued)
injuries or even death from heat stroke. Always lock the vehicle whenever leaving it.
. Outsiders can easily enter through an unlocked door when you slow down or stop your vehicle. Locking your doors can help prevent this from happening.
To lock or unlock a door, use the key from the outside or the door lock from the inside.
Power Door Locks The power door lock switches are located on the front doors. " (Unlock): Press to unlock the doors. Q (Lock): Remove the key from the ignition and press to lock the doors.
Delayed Locking When locking the doors with the power lock switch and a door or the liftgate is open, the doors will lock five seconds after the last door is closed. You will hear three chimes to signal that the delayed locking feature is in use. Pressing the power lock switch twice or the lock button on the RKE transmitter twice will override the delayed locking feature and immediately lock all the doors. This feature will not operate if the key is in the ignition. This feature can be programmed by using the Driver Information Center (DIC). See “DELAY DOOR LOCK” under Vehicle Personalization (With DIC Buttons) on page 5‑42.
2-8
Keys, Doors and Windows
Automatic Door Locks Vehicles with an automatic lock/ unlock feature enable you to program the vehicle's power door locks. This feature can be programmed through the Driver Information Center (DIC). See Vehicle Personalization (With DIC Buttons) on page 5‑42 for more information.
Lockout Protection This feature protects you from locking the key in the vehicle when the key is in the ignition and a front door is open. If the driver side power door lock switch is pressed when the driver's door is open and the key is in the ignition, all of the doors will lock and then the driver door will unlock. If the passenger side power door lock switch is pressed when the front passenger door is open and
the key is in the ignition, all of the doors will lock and then the front passenger door will unlock.
Safety Locks The vehicle has rear door security locks to prevent passengers from opening the rear doors from the inside.
To set the locks, insert a key into the slot and turn it to the horizontal position. The door can only be opened from the outside with the door unlocked. To return the door to normal operation, turn the slot to the vertical position.
Open the rear doors to access the security locks on the inside edge of each door.
Keys, Doors and Windows
2-9
Doors
Liftgate
Manual Liftgate Operation
{ WARNING
Exhaust gases can enter the vehicle if it is driven with the liftgate, trunk/hatch open, or with any objects that pass through the seal between the body and the trunk/hatch or liftgate. Engine exhaust contains Carbon Monoxide (CO) which cannot be seen or smelled. It can cause unconsciousness and even death. If the vehicle must be driven with the liftgate, or trunk/hatch open:
. Close all of the windows. . Fully open the air outlets on
or under the instrument panel.
(Continued)
WARNING (Continued)
. Adjust the Climate Control
system to a setting that brings in only outside air and set the fan speed to the highest setting. See Climate Control System in the Index. . If the vehicle is equipped with
a power liftgate, disable the power liftgate function. For more information about carbon monoxide, see Engine Exhaust on page 9‑21.
To unlock the liftgate, use the power door lock switch or press the door unlock button on the Remote Keyless Entry (RKE) transmitter twice. See Remote Keyless Entry (RKE) System Operation on page 2‑3 .
To open the liftgate, press the touchpad on the underside of the liftgate handle. The vehicle must be in P (Park) to open the liftgate. To close the liftgate, use the pull cup or strap. The liftgate has an electric latch. If the battery is disconnected or has low voltage, the liftgate will not open. The liftgate will resume operation when the battery is reconnected and charged. If the battery is properly connected and has adequate voltage, and the liftgate still will not function, the vehicle should be taken to a dealer/ retailer for service.
2-10
Keys, Doors and Windows
Power Liftgate Operation
{ WARNING
Exhaust gases can enter the vehicle if it is driven with the liftgate, trunk/hatch open, or with any objects that pass through the seal between the body and the trunk/hatch or liftgate. Engine exhaust contains Carbon Monoxide (CO) which cannot be seen or smelled. It can cause unconsciousness and even death. If the vehicle must be driven with the liftgate, or trunk/hatch open:
. Close all of the windows. . Fully open the air outlets on
or under the instrument panel.
(Continued)
WARNING (Continued)
. Adjust the Climate Control
system to a setting that brings in only outside air and set the fan speed to the highest setting. See Climate Control System in the Index. . If the vehicle is equipped with
a power liftgate, disable the power liftgate function. For more information about carbon monoxide, see Engine Exhaust on page 9‑21.
The vehicle may have a power liftgate. The vehicle must be in P (Park) to use this feature. The taillamps will flash and a chime will sound when the power liftgate is used.
{ WARNING
You or others could be injured if caught in the path of the power liftgate. Make sure there is no one in the way of the liftgate as it is opening and closing.
Notice: If you open the liftgate without checking for overhead obstructions such as a garage door, you could damage the liftgate or the liftgate glass. Always check to make sure the area above and behind the liftgate is clear before opening it. The power liftgate can be power opened and closed in the following ways: . Press and hold the power liftgate
button on the RKE transmitter until the liftgate starts moving.
Keys, Doors and Windows
2-11
function will continue to completion. If the vehicle is shifted out of P (Park) and the vehicle accelerates before the power liftgate latches closed, the liftgate may reverse to the open position. Cargo could fall out of the vehicle. The power liftgate must be closed and latched before driving. If the liftgate is power opened and the support struts have lost pressure, the lights will flash and a chime will sound. The liftgate will stay open temporarily, then slowly close. See your dealer/retailer for service before using the liftgate if this occurs.
Obstacle Detection Features A warning chime will sound and the liftgate will automatically reverse direction to the full closed or open position if the liftgate encounters an obstacle during a power open or close cycle. After removing the obstruction, the power liftgate operation can be used again.
Power Liftgate Button on Center
Power Liftgate Button near
Console
Liftgate Latch
. Press the liftgate button on the
center console.
. Press the touchpad switch on
the outside liftgate handle.
Pressing the buttons or touchpad switch a second time while the liftgate is moving reverses the direction.
The liftgate can also be closed by pressing the power liftgate button next to the liftgate latch. Press the button a second time during liftgate operation to reverse the operation. The power liftgate may be temporarily disabled under extreme temperatures or under low battery conditions. If this occurs, the liftgate can still be operated manually. If the vehicle is shifted out of P (Park) while the power function is in progress, the liftgate power
2-12
Keys, Doors and Windows
If the liftgate comes across more obstacles on the same power cycle, the power function deactivates, and you must manually open or close the liftgate. A message displays, LIFTGATE OPEN, to indicate that the liftgate is open. See Driver Information Center (DIC) (With DIC Buttons) on page 5‑24 or Driver Information Center (DIC) (Without DIC Buttons) on page 5‑30 for more information. After removing the obstructions, manually open the liftgate to the full open position or close the liftgate to the fully closed and latched position. The liftgate resumes normal power operation. Pinch sensors are located on the side edges of the liftgate. If an object is caught between the liftgate and the vehicle and presses against this sensor, the liftgate will reverse direction and open fully. The liftgate will remain open until it is activated again or closed manually. Do not force the liftgate open or closed during a power cycle.
Manual Operation of Power Liftgate
To change the liftgate to manual operation, press the switch on the center console to OFF. With the power liftgate disabled and all of the doors unlocked, the liftgate can be manually opened and closed.
To open the liftgate, press the touchpad on the handle on the outside of the liftgate and lift the gate open. To close the liftgate, use the pull cup to lower the liftgate and close. The liftgate latch will power close. Always close the liftgate before driving. If the RKE button or the power close button on the liftgate is pressed while power operation is disabled, the lights will flash three times, but the liftgate will not move. It is not recommended that you drive with the liftgate open. However, if you must drive with the liftgate open, the liftgate should be set to manual operation by pressing the OFF switch on the center console.
Vehicle Security Vehicle theft is big business, especially in some cities. This vehicle has theft-deterrent features, however, they do not make it impossible to steal.
Anti-Theft Alarm System On vehicles with an anti-theft alarm system, to activate the system: . Press Q on the Remote Keyless
Entry (RKE) transmitter or the power door lock switch when any door is open.
The security light flashes. When the door is closed, the security light stops flashing and stays on solid for approximately
Keys, Doors and Windows
2-13
30 seconds. The content theft deterrent alarm is not armed until the security light goes off. If the delayed locking feature is active, the alarm is not activated until all doors are closed and the security light goes off.
. Press Q when the driver door is closed. The security light comes on solid for approximately 30 seconds and then goes off. The content theft deterrent alarm is not armed until the security light goes off.
The theft-deterrent system will not activate if the doors are locked with the vehicle's key or the manual door lock. If a locked door is opened without using the RKE transmitter, a ten second pre-alarm occurs. The horn chirps and the lights flash. If the key is not placed in the ignition and turned to START or the door is not unlocked by pressing Q during the ten second pre-alarm, the
alarm goes off. The headlamps flash and the horn sounds for about 30 seconds, then turns off to save the battery power. The vehicle can be started with the correct ignition key if the alarm has been set off. To avoid setting off the alarm by accident:
Lock the vehicle with the door key after the doors are closed. . Unlock the door with the RKE
transmitter. Unlocking a door any other way sets off the alarm if the system has been armed. Press K or place the key in the ignition and turn it to START to turn off the alarm. Testing the Alarm To test the alarm: 1. From inside the vehicle, lower
the driver side window and open the driver door.
2. Press Q .
2-14
Keys, Doors and Windows
3. Get out of the vehicle, close the
door and wait for the security light to go out.
4. Then reach in through the
window, unlock the door with the manual door lock and open the door. This should set off the alarm.
If the alarm does not sound when it should, but the vehicle's headlamps flash, check to see if the horn works. The horn fuse may be blown. To replace the fuse, see Fuses and Circuit Breakers on page 10‑31. If the alarm does not sound or the vehicle's headlamps do not flash, see your dealer/retailer for service.
Immobilizer See Radio Frequency Statement on page 13‑16 for information regarding Part 15 of the Federal Communications Commission (FCC) Rules and RSS-210/211 of Industry and Science Canada.
Immobilizer Operation This vehicle has PASS-Key® III+ (Personalized Automotive Security System) theft-deterrent system. PASS-Key® III+ is a passive theft-deterrent system. The system is automatically armed when the key is removed from the ignition. The system is automatically disarmed when the key is turned to ON/RUN, ACC/ACCESSORY or START from the LOCK/OFF position. You do not have to manually arm or disarm the system. The security light comes on if there is a problem with arming or disarming the theft-deterrent system. When the PASS-Key® III+ system senses an incorrect key, the vehicle does not start. Anyone using a trial-and-error method to start the
vehicle will be discouraged because of the high number of electrical key codes. If the engine does not start and the security light on the instrument panel comes on when trying to start the vehicle, there may be a problem with your theft-deterrent system. Turn the ignition off and try again. If the engine still does not start, and the key appears to be undamaged, try another ignition key and check the fuses. See Fuses and Circuit Breakers on page 10‑31 for additional information. If the engine still does not start with the other key, the vehicle needs service. If the vehicle does start, the first key may be faulty. See your dealer/retailer who can service the PASS-Key® III+ to have a new key made. In an emergency, contact Roadside Assistance. See Roadside Assistance Program on page 13‑5. It is possible for the PASS-Key® III+ decoder to learn the transponder value of a new or replacement key.
Up to 10 keys may be programmed to the vehicle. The following procedure is for programming additional keys only. If all the currently programmed keys are lost or do not operate, you must see your dealer/retailer or a locksmith who can service PASS-Key® III+ to have keys made and programmed to the system. See your dealer/retailer or a locksmith who can service PASS-Key® III+ to get a new key blank that is cut exactly as the ignition key that operates the system.
Keys, Doors and Windows
2-15
To program the new additional key:
5. Repeat Steps 1 through 4 if
1. Verify that the new key has a 1
2.
stamped on it. Insert the already programmed key in the ignition and start the engine. If the engine does not start, see your dealer/retailer for service.
3. After the engine has started, turn
4.
the key to LOCK/OFF, and remove the key. Insert the key to be programmed and turn it to the ON/RUN position within five seconds of the original key being turned to the LOCK/OFF position. The security light turns off once the key has been programmed.
additional keys are to be programmed.
If the PASS-Key® III+ key is lost or damaged, see your dealer/retailer or a locksmith to have a new key made. The SERVICE THEFT DETERRENT SYSTEM message displays on the Driver Information Center (DIC) when there is a problem with the theft-deterrent system. See Anti-Theft Alarm System Messages on page 5‑38
for additional information. Do not leave the key or device that disarms or deactivates the theft deterrent system in the vehicle.2-16
Keys, Doors and Windows
Exterior Mirrors
Power Mirrors
Convex Mirrors
{ WARNING
A convex mirror can make things, like other vehicles, look farther away than they really are. If you cut too sharply into the right lane, you could hit a vehicle on the right. Check the inside mirror or glance over your shoulder before changing lanes.
The passenger side mirror is convex shaped. A convex mirror's surface is curved so more can be seen from the driver seat.
Controls for the outside power mirrors are located on the driver door armrest. To adjust each mirror: 1. Press (A) or (B) to select the
driver or passenger side mirror.
2. Press one of the four arrows located on the control pad to adjust the mirror.
3. Adjust each outside mirror so
that a little of the vehicle and the area behind it can be seen.
4. Press either (A) or (B) again to
deselect the mirror.
Folding Mirrors For vehicles with manual folding mirrors, fold the mirrors inward to prevent damage when going through an automatic car wash. To fold, push the mirror toward the vehicle. Push the mirror outward to return it to the original position.
For vehicles with outside power foldaway mirrors:
The controls for power foldaway mirrors are located on the driver door armrest. 1. Press (C) to fold the mirrors out
to the driving position.
2. Press (D) to fold the mirrors in to
the folded position.
Keys, Doors and Windows
2-17
Resetting the Power Foldaway Mirrors Reset the power foldaway mirrors if:
The mirrors are accidentally obstructed while folding. They are accidentally manually folded/unfolded. The mirrors vibrate at normal driving speeds.
Fold and unfold the mirrors one time using the mirror controls to reset them to their normal position. A popping noise may be heard during the resetting of the power foldaway mirrors. This sound is normal after a manual folding operation.
Automatic Dimming Feature The driver outside mirror adjusts for the glare of the headlamps behind you. See Automatic Dimming Rearview Mirror on page 2‑18 for information on how to turn this feature on. Turn Signal Indicator The vehicle may have a turn signal indicator lamp that is built into the mirror housing. The turn signal lamp flashes with the use of the vehicle's turn signal and hazard flashers.
Heated Mirrors For vehicles with heated mirrors: < (Rear Window Defogger): Press to heat the mirrors. See “Rear Window Defogger” under Dual Automatic Climate Control System on page 8‑4 for more information.
2-18
Keys, Doors and Windows
Park Tilt Mirrors If the vehicle has the memory package, the outside mirrors have a park tilt feature. This feature tilts the outside mirrors to a preselected position when the vehicle is in R (Reverse). This allows the driver to view the curb for parallel parking. The passenger and/or driver mirror returns to its original position when the vehicle is shifted out of R (Reverse), or the ignition is turned off or to OFF/LOCK. This feature can be turned on or off through the Driver Information Center (DIC). See Vehicle Personalization (With DIC Buttons) on page 5‑42 for more information.
Interior Mirrors
Manual Rearview Mirror Adjust the inside rearview mirror to see clearly behind your vehicle. Hold the mirror in the center to move it up or down and side to side. Use the day/night adjustment to help prevent glare from the headlamps behind you. Move the lever to the right for nighttime use and to the left for daytime use. Vehicles with OnStar® have three additional control buttons located at the bottom of the mirror. See your dealer/retailer for more information about OnStar and how to subscribe to it. See the OnStar® owner guide for more information on the services OnStar provides.
Automatic Dimming Rearview Mirror The vehicle may have an automatic dimming inside rearview mirror. Automatic dimming reduces the glare from the headlamps of the vehicle behind you. The dimming feature comes on and the indicator light illuminates each time the ignition is turned to start. Vehicles with OnStar® have three additional control buttons for the OnStar® system. See your dealer/ retailer for more information about OnStar® and how to subscribe to it. See the OnStar® owner guide for more information about the services OnStar® provides. O (On/Off): Press to turn the dimming feature on or off.
Keys, Doors and Windows
2-19
The vehicle may also have a Rear Vision Camera (RVC). See Rear Vision Camera (RVC) on page 9‑34
for more information. If the vehicle has RVC, the O button for turning the dimming feature on or off will not be available. Cleaning the Mirror Do not spray glass cleaner directly on the mirror. Use a soft towel dampened with water.Windows
{ WARNING
Leaving children, helpless adults, or pets in a vehicle with the windows closed is dangerous. They can be overcome by the extreme heat and suffer permanent injuries or even death from heat stroke. Never leave a child, a helpless adult, or a pet alone in a vehicle, especially with the windows closed in warm or hot weather.
2-20
Keys, Doors and Windows
Power Windows
{ WARNING
Leaving children in a vehicle with the keys is dangerous for many reasons, children or others could be badly injured or even killed. They could operate the power windows or other controls or even make the vehicle move. The windows will function and they could be seriously injured or killed if caught in the path of a closing window. Do not leave keys in a vehicle with children. When there are children in the rear seat use the window lockout button to prevent unintentional operation of the windows.
Express-Up/Express-Down Windows A window with the express-up/down feature allows it to be raised or lowered without holding the switch. Press or pull the window switch fully and release it to activate the express feature. The express mode can be canceled by pressing or pulling the switch. Programming the Power Windows If the battery on the vehicle has been recharged, disconnected, or replaced, windows with the express-up feature need to be reprogrammed for this feature to work. To program the window: 1. Close all doors with the ignition in the ACC/ACCESSORY, ON/ RUN position, or when Retained Accessory Power (RAP) is active. See Retained Accessory Power (RAP) on page 9‑17.
Uplevel shown, base similar
The power window controls are located on each of the side doors. The driver door also has switches that control the passenger and rear windows. The power windows work with the ignition in ACC/ ACCESSORY, ON/RUN or when Retained Accessory Power (RAP) is active. See Retained Accessory Power (RAP) on page 9‑17. Press the switch to lower the window. Pull up on the front edge of the switch to raise the window.
Keys, Doors and Windows
2-21
Window Lockout o (Window Lockout): The window lockout switch is located with the power window switches on the driver door armrest. This feature prevents the rear windows from being operated, except from the driver position. Press the switch to turn the lockout feature on or off. An indicator light will come on to show the lockout feature is on.
Sun Visors Pull the sun visor down to block glare. Detach the sun visor from the center mount and slide it along the rod from side-to-side to cover the driver or passenger side of the front window. Swing the sun visor to the side to cover the side window. It can be moved along the rod from side-to-side in this position also. Lighted Visor Vanity Mirror The vehicle has lighted visor vanity mirrors on both the driver and passenger sun visors. Pull the sun visor down and lift the mirror cover to turn the lamps on.
2. Press and continue to hold the window switch until the window is fully open.
3. Pull up and hold the window switch to close the window. Continue to hold it briefly after the window is fully closed.
4. Repeat for each window that has
the express-up feature.
Anti-Pinch Feature The anti-pinch feature is on windows with the express-up feature. If an object is in the way of the window as it is express-closing, or in certain weather conditions like severe icing, the window will stop and open to a factory preset position. The window functions normally once the obstruction is removed.
2-22
Keys, Doors and Windows
Roof
Sunroof The ignition must be in ON/RUN or ACC/ACCESSORY to operate the sunroof and power sunshade. See Retained Accessory Power (RAP) on page 9‑17
The vehicle may have a sunroof over the front seats and a rear sunroof over the second row seats. The rear sunroof does not open. The switch to operate the front sunroof is on the headliner above the rearview mirror.Vent: From the closed position, press and hold the front of the switch to vent the sunroof. Press and hold the rear of the switch to close the sunroof.
Express-open/Express-close: From the closed position, press and release the rear of the switch to express-open the sunroof. Press and release the front of the switch to express-close the sunroof. The front sunshade must be opened and closed manually. Push up on the sunshade handle to open the sunshade. Manual Sunshades On a vehicle with only manual sunshades, press the button on the sunshade handle to release it and guide it back. Pull the sunshade forward until it latches to close it. Rear Power Sunshade On vehicles with a rear power sunshade, the switch is on the headliner above the rearview mirror.
Keys, Doors and Windows
2-23
Do not keep the sunroof open for long periods of time while the vehicle is not in use. Debris can collect in the tracks, damage the sunroof operation and plug the water draining system.
Notice: The rear sunshade could be damaged if you attempt to open or close it manually. Do not manually open or close the rear sunshade. To open the rear sunshade, located over the second row seats, press and release the rear of the switch. Press and release the front of the switch to close the sunshade.
2-24
Keys, Doors and Windows
2 NOTES
Seats and Restraints
3-1
Child Restraints
Older Children . . . . . . . . . . . . . . . 3-44
Infants and YoungChildren . . . . . . . . . . . . . . . . . . . . 3-46
Child Restraint Systems . . . . . 3-49
Where to Put the Restraint . . . 3-50
Lower Anchors and Tethersfor Children (LATCH System) . . . . . . . . . . . . . . . . . . . . 3-52
Replacing LATCH System
Parts After a Crash . . . . . . . . . 3-58
Securing Child Restraints
(Rear Seat ) . . . . . . . . . . . . . . . . 3-58
Securing Child Restraints
(Right Front Passenger Seat) . . . . . . . . . . . 3-60
Seats and Restraints
Head Restraints
Head Restraints . . . . . . . . . . . . . . . 3-2
Front Seats
Seat Adjustment . . . . . . . . . . . . . . 3-3
Power Seat Adjustment . . . . . . . 3-3
Lumbar Adjustment . . . . . . . . . . . 3-5
Reclining Seatbacks . . . . . . . . . . 3-6
Heated Front Seats . . . . . . . . . . . 3-8
Heated and Ventilated FrontSeats . . . . . . . . . . . . . . . . . . . . . . . . 3-8
Rear Seats
Rear Seats . . . . . . . . . . . . . . . . . . . . 3-9
Third Row Seats . . . . . . . . . . . . . 3-11Safety Belts
Safety Belts . . . . . . . . . . . . . . . . . . 3-14
How to Wear Safety BeltsProperly . . . . . . . . . . . . . . . . . . . . 3-18
Lap-Shoulder Belt . . . . . . . . . . . 3-23
Safety Belt Use DuringPregnancy . . . . . . . . . . . . . . . . . . 3-28
Safety Belt Extender . . . . . . . . . 3-28Safety System Check . . . . . . . . 3-28
Safety Belt Care . . . . . . . . . . . . . 3-28
Replacing Safety Belt SystemParts After a Crash . . . . . . . . . 3-29
Airbag System
Airbag System . . . . . . . . . . . . . . . 3-29
Where Are the Airbags? . . . . . 3-31
When Should an AirbagInflate? . . . . . . . . . . . . . . . . . . . . . 3-33
What Makes an Airbag
Inflate? . . . . . . . . . . . . . . . . . . . . . 3-34
How Does an Airbag
Restrain? . . . . . . . . . . . . . . . . . . . 3-35
What Will You See After an
Airbag Inflates? . . . . . . . . . . . . 3-35
Passenger Sensing
System . . . . . . . . . . . . . . . . . . . . . 3-37
Servicing the Airbag-Equipped
Vehicle . . . . . . . . . . . . . . . . . . . . . 3-41
Adding Equipment to the
Airbag-Equipped Vehicle . . . 3-42
Airbag System Check . . . . . . . . 3-43
Replacing Airbag SystemParts After a Crash . . . . . . . . . 3-43
3-2
Seats and Restraints
Head Restraints The vehicle's front seats have adjustable head restraints in the outboard seating positions. { WARNING
With head restraints that are not installed and adjusted properly, there is a greater chance that occupants will suffer a neck/ spinal injury in a crash. Do not drive until the head restraints for all occupants are installed and adjusted properly.
Adjust the head restraint so that the top of the restraint is at the same height as the top of the occupant's head. This position reduces the chance of a neck injury in a crash.
1. Pull the head restraint up to
raise it. To lower the head restraint, press the release button, located on the head restraint post on the top of the seatback, while you push the head restraint down.
2. Push down on the head restraint
after the button is released to make sure that it is locked in place.
Front Seats
Seat Adjustment
{ WARNING You can lose control of the vehicle if you try to adjust a manual driver's seat while the vehicle is moving. The sudden movement could startle and confuse you, or make you push a pedal when you do not want to. Adjust the driver's seat only when the vehicle is not moving.
Seats and Restraints
3-3
Power Seat Adjustment
A. Manual Seat Adjustment Handle B. Driver Seat Height Adjuster. C. See Reclining Seatbacks on
page 3‑6 .
To adjust a manual seat: 1. Lift the handle (A) under the seat
to unlock it.
2. Slide the seat and release the
handle.
Try to move the seat to be sure it is locked in place. To manually raise or lower the seat, move the lever (B) repeatedly upward or downward.
Driver Seat with Power Seat
Control, Power Recline,
and Power Lumbar shown
A. Power Seat Adjustment Control B. Reclining Seatbacks on
page 3‑6 .
C. Lumbar Adjustment on
page 3‑5 .
On vehicles with power seats, the controls are located on the outboard side of the seats.
3-4
Seats and Restraints
Move the seat forward or rearward by sliding the power seat adjustment control (A) forward or rearward. The vehicle may have additional features to adjust the power seat: . Raise or lower the entire seat by
moving the power seat adjustment control (A) up or down.
. Raise or lower the front part of the seat cushion by moving the front of the control up or down. . Raise or lower the rear part of
the seat cushion by moving the rear of the control up or down.
Memory Seat and Mirrors
On vehicles with the memory package, the controls for this feature are located on the driver door panel. The controls are used to program and recall memory settings for the driver seat and outside mirrors. To save positions in memory: 1. Adjust the driver seat, including the seatback recliner and both outside mirrors to a comfortable position.
See Power Mirrors on page 2‑16 for more information. Not all mirrors will have the ability to save and recall the mirror positions.
2. Press and hold button 1 until two
beeps let you know that the position has been stored. A second seating and mirror position can be programmed by repeating the above steps and pressing button 2. To recall the memory positions, the vehicle must be in P (Park). Press and release either button 1 or button 2 corresponding to the desired driving position. The seat and outside mirrors will move to the position previously stored. You will hear a single beep. Using the Remote Keyless Entry (RKE) transmitter to enter the vehicle, with the remote recall memory feature on, causes automatic seat and mirror adjustment.
There is no adjustment when the position has not been changed by another seating position or the easy exit feature. See “MEMORY SEAT RECALL” under Vehicle Personalization (With DIC Buttons) on page 5‑42 for more information. To stop recall movement of the memory feature at any time, press one of the power seat controls, memory buttons, or power mirror buttons. If something has blocked the driver seat while recalling a memory position, the driver seat recall may stop working. If this happens, press the appropriate control for the area that is not recalling for two seconds, after the obstruction is removed. Then try recalling the memory position again by pressing the appropriate memory button. If the memory position is still not being recalled, see your dealer/retailer for service.
Easy Exit Seat The control for this feature is located on the driver door panel between buttons 1 and 2. With the vehicle in P (Park), the exit position can be recalled by pressing the exit button. You will hear a single beep. The driver seat will move back. If the easy exit seat feature is on in the Driver Information Center (DIC), automatic seat movement will occur when the key is removed from the ignition. See “EASY EXIT SEAT” under Vehicle Personalization (With DIC Buttons) on page 5‑42 for more information. Further programming for the memory seat feature can be done using the DIC. You can select or cancel the following:
The automatic easy exit seat feature. The remote memory seat recall feature.
Seats and Restraints
3-5
For programming information, see Vehicle Personalization (With DIC Buttons) on page 5‑42.
Lumbar Adjustment
Manual Lumbar
On vehicles with this feature, the handle is located on the inboard side of the seatback. Move the handle forward or rearward to increase or decrease lumbar support.
3-6
Seats and Restraints
Power Lumbar On vehicles with power lumbar, the control is located on the outboard side of the seat. See “Power Lumbar” under Power Seat Adjustment on page 3‑3 for more information. To increase or decrease lumbar support, press and hold the front or rear of the control (C). Release the control when the seatback reaches the desired level of lumbar support.
Reclining Seatbacks
Manual Reclining Seatbacks
{ WARNING You can lose control of the vehicle if you try to adjust a manual driver's seat while the vehicle is moving. The sudden movement could startle and confuse you, or make you push a pedal when you do not want to. Adjust the driver's seat only when the vehicle is not moving.
{ WARNING
If either seatback is not locked, it could move forward in a sudden stop or crash. That could cause injury to the person sitting there. Always push and pull on the seatbacks to be sure they are locked.
In vehicles with seats that have manual reclining seatbacks, the lever used to operate them is located on the outboard side of the seat. See Seat Adjustment on page 3‑3 . To recline the seatback: 1. Lift the recline lever (C). 2. Move the seatback to the
desired position, then release the lever to lock the seatback in place.
3. Push and pull on the seatback to
make sure it is locked.
To return the seatback to an upright position, do the following: 1. Lift the lever fully without applying pressure to the seatback and the seatback will return to the upright position.
2. Push and pull on the seatback to
make sure it is locked.
Seats and Restraints
3-7
Do not have a seatback reclined if your vehicle is moving.
Power Reclining Seatbacks In vehicles with seats that have power reclining seatbacks, the control used to recline them is located on the outboard side of the seat. See Power Seat Adjustment on page 3‑3 for more information. To recline the seatback:
Tilt the top of the control (B) rearward. To bring the seatback forward, tilt the top of the control forward.
{ WARNING
Sitting in a reclined position when the vehicle is in motion can be dangerous. Even when buckled up, the safety belts cannot do their job when reclined like this. The shoulder belt cannot do its job because it will not be against your body. Instead, it will be in front of you. In a crash, you could go into it, receiving neck or other injuries. The lap belt cannot do its job either. In a crash, the belt could go up over your abdomen. The belt forces would be there, not at your pelvic bones. This could cause serious internal injuries. For proper protection when the vehicle is in motion, have the seatback upright. Then sit well back in the seat and wear the safety belt properly.
3-8
Seats and Restraints
Heated Front Seats { WARNING
If you cannot feel temperature change or pain to the skin, the seat heater may cause burns even at low temperatures. To reduce the risk of burns, people with such a condition should use care when using the seat heater, especially for long periods of time. Do not place anything on the seat that insulates against heat, such as a blanket, cushion, cover or similar item. This may cause the seat heater to overheat. An overheated seat heater may cause a burn or may damage the seat.
On vehicles with heated front seats, the controls are located on the center console. To operate the heated seats the engine must be running.
I (Heated Seatback): Press to turn on the heated seatback. J (Heated Seat and Seatback): Press to turn on or off the heated seat and seatback. The light on the button will come on to indicate that the feature is on. Each time the button is pressed, the temperature settings change from high, to medium, to low, to off. Indicator lights above the button will show the level of heat selected: three for high, two for medium, and one for low. The passenger seat may take longer to heat up. If the vehicle has remote vehicle start and is started using the RKE transmitter, the front heated seats will be turned on to the high setting if it is cold outside. See “Remote Vehicle Start” under Remote Keyless Entry (RKE) System Operation on page 2‑3 . When the ignition is turned on, the heated seat
feature will turn off. To turn the heated seat feature back on, press the desired button.
Heated and Ventilated Front Seats
{ WARNING
If you cannot feel temperature change or pain to the skin, the seat heater may cause burns even at low temperatures. To reduce the risk of burns, people with such a condition should use care when using the seat heater, especially for long periods of time. Do not place anything on the seat that insulates against heat, such as a blanket, cushion, cover or similar item. This may cause the seat heater to overheat. An overheated seat heater may cause a burn or may damage the seat.
On vehicles with the heated and ventilated seat feature, the controls are located on the front doors near the door handle. H (Ventilated Seat): Press to ventilate the entire seat. This symbol appears on the climate control display to indicate that the feature is on. z (Heated Seat and Seatback): Press to heat the entire seat. This symbol appears on the climate control display to indicate that the feature is on.
For either feature press the button once for the highest setting. With each press of the switch, the seat changes to the next lower setting, and then the off setting. The lights indicate three for the highest setting and one for the lowest. The heated and ventilated seats are canceled after the ignition is turned off. To use the heated and ventilated seat feature after the vehicle is started, you will need to press the appropriate seat button again.
Seats and Restraints
3-9
Rear Seats
A. Seat Adjustment Handle B. Reclining Seatback Strap C. Sliding Seat Lever
3-10
Seats and Restraints
Entering and Exiting the Third Row
{ WARNING Using the third row seating position while the second row is folded, or folded and tumbled, could cause injury in a sudden stop or crash. Be sure to return the seat to the passenger seating position. Push and pull on the seat to make sure it is locked into place.
Notice: Folding a rear seat with the safety belts still fastened may cause damage to the seat or the safety belts. Always unbuckle the safety belts and return them to their normal stowed position before folding a rear seat.
5. Pull the sliding seat lever (C)
forward and move the seatback forward. The seat cushion will fold, and the entire seat will slide forward.
Returning the Seat to the Seating Position To return the second row seat to its normal seating position: 1. Remove objects on the floor
behind the second row seat or in the seat tracks on the floor.
2. Pull the seatback rearward until
it is locked in place.
3. Slide the seat rearward by
pushing on the seatback until it is locked into place.
4. Push down on the rear of the
seat cushion until it is locked in place.
5. Push and pull on the seatback and seat cushion to make sure they are locked in place.
6. Check that the safety belt is not
under the seat cushion.
To access the third row: 1. Remove objects on the floor in
front of or on the second row seat, or in the seat tracks on the floor.
2. Move the front center console
armrest completely forward. See Center Console Storage on page 4‑1 .
3. Place folding armrests in the
upright position.
4. Ensure that the safety belt is unfastened and in the stowed position.
To return the seatback to the seating position, lift the upper corner of the seatback and push it rearward until it locks into place. Push and pull on the seatback to make sure it is locked. Adjusting the Seats To adjust the second row seats, pull outward on the seat adjustment handle (A). Slide the seat forward or rearward to the desired position. Release the handle and push and pull on the seat to make sure it is locked.
Reclining the Seatbacks To recline the seatback: 1. Leaning forward in the seat, pull the reclining seatback strap (B).
2. Move the seatback to the
desired position, then release the strap to lock the seatback in place.
3. Push and pull on the seatback to
make sure it is locked. Folding the Rear Seat To fold the second row seats: 1. Remove anything on or under
the seat.
2. Place the armrest in the upright
position, and unfasten the safety belt.
3. Pull forward on the reclining seatback strap (B) and push down on the seatback. If the headrest touches the front seat, slide the second row seat rearward.
Seats and Restraints
3-11
Third Row Seats
{ WARNING Using the third row seating position while the second row is folded, or pushed forward in the entry position, could cause injury in a sudden stop or crash. Be sure to return the seat to the passenger seating position. Push and pull on the seat to make sure it is locked into place.
The third row seats can be folded forward or removed. Notice: Folding a rear seat with the safety belts still fastened may cause damage to the seat or the safety belts. Always unbuckle the safety belts and return them to their normal stowed position before folding a rear seat. To fold the seatback: 1. Remove anything on or under
the seat.
3-12
Seats and Restraints
2. Disconnect the rear safety belt
mini-latch, using a key in the slot on the mini-buckle, let the belt retract into the headliner. Stow the mini-latch in the holder located in the headliner.
3. Pull up on the release lever
located on the back of the seat. The headrest moves forward automatically.
4. Push the seatback forward to
lay flat.
To return the seatback to the seating position: 1. Raise the seatback into place by using the pullstrap from the rear of the vehicle, or by pushing it into place from inside the vehicle.
2. The headrest must be locked
into place before sitting in the seat.
{ WARNING
If either seatback is not locked, it could move forward in a sudden stop or crash. That could cause injury to the person sitting there. Always push and pull on the seatbacks to be sure they are locked.
3. Push and pull on the seatback to
make sure it is locked in place.
{ WARNING
A safety belt that is improperly routed, not properly attached, or twisted will not provide the protection needed in a crash. The person wearing the belt could be seriously injured. After raising the rear seatback, always check to be sure that the safety belts are properly routed and attached, and are not twisted.
4. Reconnect the center safety belt mini-latch to the mini-buckle. Do not let it twist.
5. Pull on the safety belt to be sure
the mini-latch is secure.
Removing the Third Row Seats 1. Remove the cargo management system, if it is in the vehicle. See Cargo Management System on page 4‑3 .
2. Remove anything on or under
the seat.
Notice: Folding a rear seat with the safety belts still fastened may cause damage to the seat or the safety belts. Always unbuckle the safety belts and return them to their normal stowed position before folding a rear seat. 3. Fold the seatback down. See
“Folding the Seatback” earlier in this section.
4. Remove the rear bolts located
on the floor on each side of the seat.
Seats and Restraints
3-13
5. Remove the seat by tilting it
slightly upward, and then pulling it out of the rear of the vehicle in one motion.
6. Replace the bolts in the floor
holes for storage.
Installing the Third Row Seats 1. Before installing the seat the
seatback must be folded forward. See “Folding the Seatback” earlier in this section. The seats must be placed in the proper locations to attach correctly. The wider seat must be installed on the driver side and the narrower seat on the passenger side. Remove the bolts from the holes in the floor before installing the seats.
3-14
Seats and Restraints
2. Place the seat on the vehicle
floor so that the front seat hooks are on the vehicle bars.
3. Reinstall the bolts, and torque to
55 Y (41 lb ft). Pull up on the seat to make sure it is locked in place.
4. Raise the seatback to its upright
position. Push and pull on the seatback to make sure it is locked into place.
5. Push the headrest up into
position. Push and pull on the headrest to make sure it is locked into place.
6. Reconnect the center safety belt mini-latch to the mini-buckle. Do not let it twist.
Safety Belts This section of the manual describes how to use safety belts properly. It also describes some things not to do with safety belts.
{ WARNING
Do not let anyone ride where a safety belt cannot be worn properly. In a crash, if you or your passenger(s) are not wearing safety belts, the injuries can be much worse. You can hit things inside the vehicle harder or be ejected from the vehicle. You and your passenger(s) can be seriously injured or killed. In the same crash, you might not be, if you are buckled up. Always fasten your safety belt, and check that your passenger(s) are restrained properly too.
{ WARNING
It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. Do not allow people to ride in any area of your vehicle that is not equipped with seats and safety belts. Be sure everyone in your vehicle is in a seat and using a safety belt properly.
This vehicle has indicators as a reminder to buckle the safety belts. See Safety Belt Reminders on page 5‑15 for additional information. In most states and in all Canadian provinces, the law requires wearing safety belts. Here is why: You never know if you will be in a crash. If you do have a crash, you do not know if it will be a serious one.
A few crashes are mild, and some crashes can be so serious that even buckled up, a person would not survive. But most crashes are in between. In many of them, people who buckle up can survive and sometimes walk away. Without safety belts they could have been badly hurt or killed. After more than 40 years of safety belts in vehicles, the facts are clear. In most crashes buckling up does matter ... a lot!
Seats and Restraints
3-15
Why Safety Belts Work When you ride in or on anything, you go as fast as it goes.
Put someone on it.
Take the simplest vehicle. Suppose it is just a seat on wheels.
Get it up to speed. Then stop the vehicle. The rider does not stop.
3-16
Seats and Restraints
The person keeps going until stopped by something. In a real vehicle, it could be the windshield...
or the instrument panel...
or the safety belts! With safety belts, you slow down as the vehicle does. You get more time to stop. You stop over more distance, and your strongest bones take the forces. That is why safety belts make such good sense.
Questions and Answers About Safety Belts Q: Will I be trapped in the vehicle after a crash if I am wearing a safety belt?
A: You could be — whether you are wearing a safety belt or not. But your chance of being conscious during and after an accident, so you can unbuckle and get out, is much greater if you are belted. And you can unbuckle a safety belt, even if you are upside down.
Q: If my vehicle has airbags, why
should I have to wear safety belts?
A: Airbags are supplemental
systems only; so they work with safety belts — not instead of them. Whether or not an airbag is provided, all occupants still have to buckle up to get the most protection. That is true not only in frontal collisions, but especially in side and other collisions.
Seats and Restraints
3-17
Q: If I am a good driver, and I never drive far from home, why should I wear safety belts?
A: You may be an excellent driver, but if you are in a crash — even one that is not your fault — you and your passenger(s) can be hurt. Being a good driver does not protect you from things beyond your control, such as bad drivers. Most accidents occur within 40 km (25 miles) of home. And the greatest number of serious injuries and deaths occur at speeds of less than 65 km/h (40 mph). Safety belts are for everyone.
3-18
Seats and Restraints
How to Wear Safety Belts Properly This section is only for people of adult size. Be aware that there are special things to know about safety belts and children. And there are different rules for smaller children and infants. If a child will be riding in the vehicle, see Older Children on page 3‑44 or Infants and Young Children on page 3‑46 . Follow those rules for everyone's protection. It is very important for all occupants to buckle up. Statistics show that unbelted people are hurt more often in crashes than those who are wearing safety belts. Occupants who are not buckled up can be thrown out of the vehicle in a crash. And they can strike others in the vehicle who are wearing safety belts.
First, before you or your passenger(s) wear a safety belt, there is important information you should know.
shoulder belt should go over the shoulder and across the chest. These parts of the body are best able to take belt restraining forces. The shoulder belt locks if there is a sudden stop or crash. Q: What is wrong with this?
Sit up straight and always keep your feet on the floor in front of you. The lap part of the belt should be worn low and snug on the hips, just touching the thighs. In a crash, this applies force to the strong pelvic bones and you would be less likely to slide under the lap belt. If you slid under it, the belt would apply force on your abdomen. This could cause serious or even fatal injuries. The
A: The shoulder belt is too loose.
It will not give as much protection this way.
{ WARNING
Q: What is wrong with this?
{ WARNING
Seats and Restraints
3-19
You can be seriously hurt if your shoulder belt is too loose. In a crash, you would move forward too much, which could increase injury. The shoulder belt should fit snugly against your body.
You can be seriously hurt if your lap belt is too loose. In a crash, you could slide under the lap belt and apply force on your abdomen. This could cause serious or even fatal injuries. The lap belt should be worn low and snug on the hips, just touching the thighs.
A: The lap belt is too loose. It will
not give nearly as much protection this way.
3-20
Seats and Restraints
Q: What is wrong with this?
{ WARNING
Q: What is wrong with this?
You can be seriously injured if your belt is buckled in the wrong place like this. In a crash, the belt would go up over your abdomen. The belt forces would be there, not on the pelvic bones. This could cause serious internal injuries. Always buckle your belt into the buckle nearest you.
A: The belt is buckled in the wrong
buckle.
A: The belt is over an armrest.
{ WARNING
Q: What is wrong with this?
{ WARNING
Seats and Restraints
3-21
You can be seriously injured if your belt goes over an armrest like this. The belt would be much too high. In a crash, you can slide under the belt. The belt force would then be applied on the abdomen, not on the pelvic bones, and that could cause serious or fatal injuries. Be sure the belt goes under the armrests.
You can be seriously injured if you wear the shoulder belt under your arm. In a crash, your body would move too far forward, which would increase the chance of head and neck injury. Also, the belt would apply too much force to the ribs, which are not as strong as shoulder bones. You could also severely injure internal organs like your liver or spleen.
