Login- Download PDF Manual
-
{CAUTION:
Engine exhaust can kill. It contains the gas carbon monoxide (CO), which you cannot see or smell. It can cause unconsciousness and death. You might have exhaust coming in if:
(cid:129) The exhaust system sounds strange
or different.
(cid:129) Your vehicle gets rusty underneath. (cid:129) Your vehicle was damaged in a
collision.
CAUTION:
(Continued)
(cid:129) Your vehicle was damaged when
driving over high points on the road or over road debris.
(cid:129) Repairs were not done correctly. (cid:129) Your vehicle or the exhaust system
has been modified improperly.
If you ever suspect exhaust is coming into your vehicle:
(cid:129) Drive it only with all the windows
down to blow out any CO; and
(cid:129) Have your vehicle fixed immediately.
CAUTION:
(Continued)
137
Running the Engine While Parked It is better not to park with the engine running. But if you ever have to, here are some things to know.
{CAUTION:
Idling the engine with the climate control system off could allow dangerous exhaust into your vehicle. See the earlier caution under Engine Exhaust on page 137. Also, idling in a closed-in place can let deadly carbon monoxide (CO) into your vehicle even if the climate control fan is at the highest setting. One place this can happen is a garage. Exhaust — with CO — can come in easily. NEVER park in a garage with the engine running. Another closed-in place can be a blizzard. See Winter Driving on page 347.
{CAUTION:
It can be dangerous to get out of your vehicle if the shift lever is not fully in PARK (P) with the parking brake firmly set. Your vehicle can roll. Do not leave your vehicle when the engine is running unless you have to. If you have left the engine running, the vehicle can move suddenly. You or others could be injured. To be sure your vehicle will not move, even when you are on fairly level ground, always set the parking brake and move the shift lever to PARK (P).
Follow the proper steps to be sure your vehicle will not move. See Shifting Into Park (P) on page 134. If you are pulling a trailer, see Towing a Trailer on page 362.
138
Mirrors
Manual Rearview Mirror with OnStar® When you are sitting in a comfortable driving position, adjust the mirror so you can see clearly behind your vehicle. Hold the mirror in the center to move it up or down and side to side. The day/night adjustment allows you to adjust the mirror to avoid glare from the lamps behind you. Move the lever to the right for nighttime use and to the left for daytime use. There may also be three OnStar® buttons located at the bottom of the mirror face. See your dealer/retailer for more information on the system and how to subscribe to OnStar®. See OnStar® System on page 145 for more information on the services OnStar® provides.
Automatic Dimming Rearview Mirror with OnStar® and Compass Your vehicle may have an automatic-dimming rearview mirror with a compass. There may be three additional buttons for the OnStar® system. See your dealer/retailer for more information on the system and how to subscribe to OnStar®. See OnStar® System on page 145 for more information about the services OnStar® provides. O (On/Off): This is the on/off button. Automatic Dimming Mirror Operation The automatic dimming mirror comes on each time the ignition is turned to start. To turn the automatic dimming feature off or back on, press the on/off button. The indicator light on the mirror is lit when the automatic dimming feature is on.
139
Compass Variance Compass variance is the difference between earth’s magnetic north and true geographic north. The mirror is set to zone eight upon leaving the factory. It will be necessary to adjust the compass to compensate for compass variance if you live outside zone eight. Under certain circumstances, such as during a long distance cross-country trip, it will be necessary to adjust for compass variance. If not adjusted to account for compass variance, your compass could give false readings.
Compass Operation Press the on/off button once to turn the compass on or off. There is a compass display in the window in the upper right corner of the mirror face. Compass Calibration Press and hold the on/off button to activate the compass calibration mode. CAL will be displayed in the compass window on the mirror. The compass can be calibrated by driving the vehicle in circles at 5 mph (8 km/h) or less until the display reads a direction. If after a few seconds the display does not show a compass direction, (N for North for example), there may be a strong magnetic field interfering with the compass. Such interference may be caused by a magnetic antenna mount, note pad holder, or similar object. If the letter C or CAL appears in the compass window, the compass may need to be reset or calibrated.
140
To adjust for compass variance: 1. Find your current location and variance zone
number on the following zone map.
3. Scroll through the zone numbers that appear in the window on the mirror by pressing the on/off button. Once you find your zone number, release the button. After about four seconds, the mirror will return to the compass display, and the new zone number will be set. If C or CAL appears in the compass window, the compass may need calibration. See “Compass Calibration” listed previously.
2. Press and hold the on/off button until the zone
number is displayed. The number shown is the current zone number.
141
The mirrors can be manually folded inward to prevent damage when going through an automatic car wash. To fold, push the mirror toward the vehicle. To return the mirror to its original position, push outward. Be sure to return both mirrors to their original unfolded position before driving. The use of hood-mounted air deflectors and add-on convex mirror attachments may adversely affect mirror performance. Turn Signal Indicator Your vehicle may have a turn signal indicator on the mirror. An arrow on the mirror will flash in the direction of the turn or lane change.
Outside Power Mirrors
If your vehicle is equipped with outside power mirrors, the controls are located on the driver’s door armrest.
Press (A) to select the driver’s side mirror or (B) to select the passenger’s side mirror. Press either (A) or (B) again to deselect the mirror. To adjust each mirror, press one of the four arrows located on the control pad to move the mirror in the direction you want it to go. Adjust each outside mirror so that you can see a little of your vehicle, and the area behind your vehicle. See Memory Seat and Mirrors on page 13 for more information.
142
Outside Power Foldaway Mirrors
If your vehicle is equipped with outside power foldaway mirrors, the controls are located on the driver’s door armrest.
(cid:129) Press (A) to select the driver’s side mirror. Then
press the arrows located on the four-way control pad to adjust the mirror. Press (A) again to deselect the mirror.
(cid:129) Press (B) to select the passenger’s side mirror. Then press the arrows located on the four-way control pad to adjust the mirror. Press (B) again to deselect the mirror.
(cid:129) Press (C), to fold the mirrors out to the driving
(cid:129) Press (D) to fold the mirrors in to the folded
position.
position.
If the mirrors are accidentally folded/unfolded manually, they may shake or flutter at normal driving speeds and may not stay in the unfolded position. If this happens, you will need to reset the mirrors. See “Resetting the Power Foldaway Mirrors” next. Resetting the Power Foldaway Mirrors You will need to reset the power foldaway mirrors if the following occurs: (cid:129) The mirrors are accidentally obstructed while
folding.
(cid:129) They are accidentally manually
folded/unfolded.
(cid:129) The mirrors will not stay in the unfolded
position.
(cid:129) The mirrors shake and flutter at normal driving
speeds.
To reset the power foldaway mirrors, fold and unfold them one time using the mirror controls. This will reset them to their normal position. This mirror has the following features.
143
Automatic Dimming The driver’s outside mirror will adjust for the glare of the headlamps behind you. See Automatic Dimming Rearview Mirror with OnStar® and Compass on page 139. Curb View Assist If your vehicle has the memory package, the outside mirrors are able to perform the curb view assist mirror function. This feature may be useful in allowing the driver to view the curb when parallel parking. This feature will cause the passenger’s and/or driver’s mirror to tilt to a preselected position when the vehicle is in REVERSE (R). The passenger’s and/or driver’s mirror will return to its original position when the vehicle is shifted out of REVERSE (R), or the ignition is turned off or to LOCK. This feature can be turned on or off through the Driver Information Center (DIC). See Driver Information Center (DIC) on page 228 and Memory Seat and Mirrors on page 13 for more information.
Turn Signal Indicator Your vehicle may have a turn signal indicator on the mirror. An arrow on the mirror will flash in the direction of the turn or lane change. Outside Convex Mirror
{CAUTION:
A convex mirror can make things (like other vehicles) look farther away than they really are. If you cut too sharply into the right lane, you could hit a vehicle on your right. Check your inside mirror or glance over your shoulder before changing lanes.
The passenger’s side mirror may have convex glass. A convex mirror’s surface is curved so more can be seen from the driver’s seat.
144
Outside Heated Mirrors Press the rear window defogger button, located on the climate control panel, to also turn the outside heated mirrors on or off. The mirrors will heat to help clear fog or frost from the surface of the mirror. See “Rear Window Defogger” under Dual Automatic Climate Control System on page 198
for more information. OnStar® SystemOnStar® uses several innovative technologies and live advisors to provide you with a wide range of safety, security, information, and convenience services. If your airbags deploy, the system is designed to make an automatic call to OnStar® Emergency advisors who can request emergency
services be sent to your location. If you lock your keys in the vehicle, call OnStar® at 1-888-4-ONSTAR and they can send a signal to unlock your doors. If you need roadside assistance, press the OnStar® button and they can contact Roadside Service for you. OnStar® service is provided to you subject to the OnStar® Terms and Conditions. You may cancel your OnStar® service at any time by contacting OnStar®. A complete OnStar® Owner’s Guide and the OnStar® Terms and Conditions are included in the vehicle’s OnStar® Subscriber glove box literature. For more information, visit onstar.com or onstar.ca, contact OnStar® at 1-888-4-ONSTAR (1-888-466-7827) or TTY 1-877-248-2080, or press the OnStar® button to speak with an OnStar® advisor 24 hours a day, 7 days a week. Not all OnStar® features are available on all vehicles. To check if your vehicle is equipped to provide the services described below, or for a full description of OnStar® services and system limitations, see the OnStar® Owner’s Guide in your glove box or visit onstar.com.
145
OnStar® Services For new vehicles with OnStar®, the Safe & Sound Plan, or the Directions & Connections® Plan is included for one year from the date of purchase. You can extend this plan beyond the first year, or upgrade to the Directions & Connections® Plan. For more information, press the OnStar® button to speak with an advisor. Some OnStar® services (such as Remote Door Unlock or Stolen Vehicle Location Assistance) may not be available until you register with OnStar®. Available Services with Safe & Sound® Plan (cid:129) Automatic Notification of Airbag Deployment (cid:129) Advanced Automatic Crash Notification
(AACN) (If equipped) Link to Emergency Services
(cid:129) Roadside Assistance (cid:129) Stolen Vehicle Location Assistance (cid:129) AccidentAssist
(cid:129) Remote Door Unlock/Vehicle Alert (cid:129) OnStar® Vehicle Diagnostics (cid:129) GM Goodwrench® On Demand Diagnostics (cid:129) OnStar® Hands-Free Calling with
30 complimentary minutes
(cid:129) OnStar® Virtual Advisor (U.S. Only) Available Services included with Directions & Connections® Plan (cid:129) All Safe and Sound Plan Services (cid:129) Driving Directions - Advisor delivered or
OnStar® Turn-by-Turn Navigation (If equipped)
(cid:129) RideAssist
Information and Convenience Services
OnStar® Hands-Free Calling OnStar® Hands-Free Calling allows eligible OnStar® subscribers to make and receive calls using voice commands. Hands-Free Calling is fully integrated into the vehicle, and can be used with OnStar® Pre-Paid Minute Packages.
146
(cid:129) (cid:129) Hands-Free Calling may also be linked to a Verizon Wireless service plan in the U.S. or a Bell Mobility service plan in Canada, depending on eligibility. To find out more, refer to the OnStar® Owner’s Guide in the vehicle’s glove box, visit www.onstar.com or www.onstar.ca, or speak with an OnStar® advisor by pressing the OnStar® button or calling 1-888-4-ONSTAR (1-888-466-7827). OnStar® Virtual Advisor OnStar® Virtual Advisor is a feature of OnStar® Hands-Free Calling that uses your minutes to access location-based weather, local traffic reports, and stock quotes. By pressing the phone button and giving a few simple voice commands, you can browse through the various topics. See the OnStar® Owner’s Guide for more information (Only available in the continental U.S.). OnStar® Steering Wheel Controls Your vehicle may have a Talk/Mute button that can be used to interact with OnStar® Hands-Free Calling. See Audio Steering Wheel Controls on page 317 for more information.
On some vehicles, you may have to hold the button for a few seconds and give the command “ONSTAR” in order to activate the OnStar® Hands-Free Calling feature. On some vehicles, the mute button can be used to dial numbers into voicemail systems, or to dial phone extensions. See the OnStar® Owner’s Guide for more information. How OnStar® Service Works In order to provide you with OnStar® services, your vehicle’s OnStar® system has the capability of recording and transmitting vehicle information. This information is automatically sent to an OnStar® Call Center at the time of an OnStar® button press, Emergency button press or if your airbags or AACN system deploys. The vehicle information usually includes your GPS location and, in the event of a crash, additional information regarding the accident that your vehicle has been involved in (e.g. the direction from which your vehicle was hit). When you use the Virtual Advisor feature of OnStar® Hands-Free Calling, your vehicle also sends OnStar® your GPS location so that we can provide you with location-based services.
147
OnStar® service cannot work unless your vehicle is in a place where OnStar® has an agreement with a wireless service provider for service in that area. OnStar® service also cannot work unless you are in a place where the wireless service provider OnStar® has hired for that area has coverage, network capacity and reception when the service is needed, and technology that is compatible with the OnStar® service. Not all services are available everywhere, particularly in remote or enclosed areas, or at all times. OnStar® service that involves location information about your vehicle cannot work unless GPS satellite signals are unobstructed and available in that place as well.
Your vehicle must have a working electrical system (including adequate battery power) for the OnStar® equipment to operate. There are other problems OnStar® cannot control that may prevent OnStar® from providing OnStar® service to you at any particular time or place. Some examples are damage to important parts of your vehicle in an accident, hills, tall buildings, tunnels, weather or wireless phone network congestion. Your Responsibility You may need to increase the volume of your radio to hear the OnStar® advisor. If the light next to the OnStar® buttons is red, this means that your system is not functioning properly and should be checked by your dealer/retailer. If the light appears clear (no light is appearing), your OnStar® subscription has expired. You can always press the OnStar® button to confirm that your OnStar® equipment is active.
148
Universal Home Remote System
System Identification Your vehicle may have a Universal Home Remote System. Determine which Universal Home Remote your vehicle has and then read the pages following for instructions on programming your specific system.
If there is one triangular Light Emitting Diode (LED) indicator light above the Universal Home Remote buttons, follow the instructions under Universal Home Remote System Operation (With One Triangular LED).
If there are three round LED indicator lights above the Universal Home Remote buttons, follow the instructions under Universal Home Remote System Operation (With Three Round LED). For help or information on the Universal Home Remote System, call the customer assistance phone number under Customer Assistance Offices on page 508.
Universal Home Remote System The Universal Home Remote System provides a way to replace up to three hand-held Radio-Frequency (RF) transmitters used to activate devices such as garage door openers, security systems, and home lighting.
149
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful
interference.
2. This device must accept any interference received, including interference that may cause undesired operation.
This device complies with RSS-210 of Industry Canada. Operation is subject to the following two conditions: 1. This device may not cause interference. 2. This device must accept any interference received, including interference that may cause undesired operation of the device.
Changes or modifications to this system by other than an authorized service facility could void authorization to use this equipment.
Universal Home Remote System Operation (With One Triangular LED)
If there is one triangular Light Emitting Diode (LED) indicator light above the Universal Home Remote buttons, follow the instructions below. Do not use the Universal Home Remote with any garage door opener that does not have the stop and reverse feature. This includes any garage door opener model manufactured before April 1, 1982. If you have a newer garage door opener with rolling codes, please be sure to follow Steps 6 through 8 to complete the programming of your Universal Home Remote Transmitter.
150
Read the instructions completely before attempting to program the Universal Home Remote. Because of the steps involved, it may be helpful to have another person available to assist you in the programming steps Keep the original hand-held transmitter for use in other vehicles as well as for future Universal Home Remote programming. It is also recommended that upon the sale of the vehicle, the programmed Universal Home Remote buttons should be erased for security purposes. See “Erasing Universal Home Remote Buttons” later in section. When programming a garage door, it is advised to park outside of the garage. Be sure that people and objects are clear of the garage door or gate operator you are programming. It is recommended that a new battery be installed in your hand-held transmitter for quicker and more accurate transmission of the radio-frequency signal.
Programming the Universal Home Remote System To program up to three devices: 1. Press and hold down the two outside
Universal Home Remote buttons, releasing only when the Universal Home Remote indicator light begins to flash, after 20 seconds. Do not hold down the buttons for longer than 30 seconds and do not repeat this step to program a second and/or third hand-held transmitter to the remaining two Universal Home Remote buttons.
2. Hold the end of your hand-held transmitter about 1 to 3 inches (3 to 8 cm) away from the Universal Home Remote buttons while keeping the indicator light in view.
3. At the same time, press and hold both the
desired Universal Home Remote button and the hand-held transmitter button. Do not release the buttons until Step 4 has been completed. Some entry gates and garage door openers may require you to substitute Step 3 with the procedure noted in “Gate Operator and Canadian Programming” later in this section.
151
4. The indicator light will flash slowly at first and
then rapidly after Universal Home Remote successfully receives the frequency signal from the hand-held transmitter. Release both buttons.
6. Locate in the garage, the garage door opener receiver (motor-head unit). Locate the “Learn” or “Smart” button. This can usually be found where the hanging antenna wire is attached to the motor-head unit.
5. Press and hold the newly-trained Universal
Home Remote button and observe the indicator light. If the indicator light stays on continuously, programming is complete and your device should activate when the Universal Home Remote button is pressed and released. To program the remaining two Universal Home Remote buttons, begin with Step 2 under “Programming Universal Home Remote.” Do not repeat Step 1 as this will erase all of the programmed channels. If the indicator light blinks rapidly for two seconds and then turns to a constant light, continue with Steps 6 through 8 following to complete the programming of a rolling-code device, most commonly, a garage door opener.
7. Firmly press and release the “Learn” or “Smart” button. The name and color of the button may vary by manufacturer. You will have 30 seconds to start Step 8.
8. Return to the vehicle. Firmly press and hold
the programmed Universal Home Remote button for two seconds, then release it. Immediately press and hold the same button a second time for two seconds, then release it. Immediately, press and hold the same button a third time for two seconds, then release. The Universal Home Remote should now activate the rolling-code device.
To program the remaining two Universal Home Remote buttons, begin with Step 2 of “Programming Universal Home Remote.” Do not repeat Step 1, as this will erase all previous programming from the Universal Home Remote buttons.
152
Gate Operator and Canadian Programming Canadian radio-frequency laws require transmitter signals to time out or quit after several seconds of transmission. This may not be long enough for Universal Home Remote to pick up the signal during programming. Similarly, some U.S. gate operators are manufactured to time out in the same manner. If you live in Canada, or you are having difficulty programming a gate operator or garage door opener by using the “Programming Universal Home Remote” procedures, regardless of where you live, replace Step 3 under “Programming Universal Home Remote” with the following: Continue to press and hold the Universal Home Remote button while you press and release every two seconds (cycle) the hand-held transmitter button until the frequency signal has been successfully accepted by the Universal Home Remote. The Universal Home Remote indicator light will flash slowly at first and then rapidly. Proceed with Step 4 under “Programming Universal Home Remote” to complete.
Using Universal Home Remote Press and hold the appropriate Universal Home Remote button for at least half of a second. The indicator light will come on while the signal is being transmitted. Erasing Universal Home Remote Buttons To erase programming from the three Universal Home Remote buttons: 1. Press and hold down the two outside buttons
until the indicator light begins to flash, after 20 seconds. Do not hold the two outside buttons for longer than 30 seconds.
2. Release both buttons. The Universal Home Remote is now in the training (learning) mode and can be programmed at any time beginning with Step 2 under “Programming Universal Home Remote” shown earlier in this section. Individual buttons cannot be erased, but they can be reprogrammed. See “Reprogramming a Single Universal Home Remote Button” following this section.
153
Reprogramming a Single Universal Home Remote Button To program a device to Universal Home Remote using a Universal Home Remote button previously trained: 1. Press and hold the desired Universal Home
Remote button. Do not release the button. 2. The indicator light will begin to flash after
20 seconds. While still holding the Universal Home Remote button, proceed with Step 2 under “Programming Universal Home Remote” shown earlier in this section.
For help or information on the Universal Home Remote System, call the customer assistance phone number under Customer Assistance Offices on page 508.
154
Universal Home Remote System Operation (With Three Round LED)
Your vehicle may have the Universal Home Remote System. If there are three round Light Emitting Diode (LED) indicator lights above the Universal Home Remote buttons, follow the instructions below. This system provides a way to replace up to three remote control transmitters used to activate devices such as garage door openers, security systems, and home automation devices. Do not use this system with any garage door opener that does not have the stop and reverse feature. This includes any garage door opener model manufactured before April 1, 1982.
Read the instructions completely before attempting to program the transmitter. Because of the steps involved, it may be helpful to have another person available to assist you in programming the transmitter. Be sure to keep the original remote control transmitter for use in other vehicles, as well as, for future programming. You only need the original remote control transmitter for Fixed Code programming. It is also recommended that upon the sale or lease termination of the vehicle, the programmed buttons should be erased for security purposes. See “Erasing Universal Home Remote Buttons” later in this section. When programming a garage door, it is advised to park outside of the garage. Be sure that people and objects are clear of the garage door or security device you are programming. Programming Universal Home Remote — Rolling Code Most garage door openers sold after 1996 are Rolling Code units.
Programming a garage door opener involves time-sensitive actions, so read the entire procedure before you begin. If you do not follow these actions, the device will time out and you will have to repeat the procedure. To program up to three devices:
1. From inside the vehicle, press the
two outside buttons at the same time for one to two seconds, and immediately release them.
155
3. Immediately return to your vehicle. Press and
hold the universal home remote button that you would like to use to control the garage door until the garage door moves. The indicator light, above the selected button, should slowly blink. You may need to hold the button from five to 20 seconds.
4. Immediately, within one second, release the
button when the garage door moves. The indicator light will blink rapidly until programming is complete.
5. Press and release the same button again. The garage door should move, confirming that programming is successful and complete. To program another Rolling Code device such as an additional garage door opener, a security device, or home automation device, repeat Steps 1 through 5, choosing a different function button in Step 3 than what you used for the garage door opener. If these instructions do not work, you probably have a Fixed Code garage door opener. Follow the Programming instructions that follow for a Fixed Code garage door opener.
2. Locate in the garage, the garage door opener receiver (motor-head unit). Locate the “Learn” or “Smart” button. It can usually be found where the hanging antenna wire is attached to the motor-head unit and may be a colored button. Press this button. After you press this button, you will have 30 seconds to complete the following steps.
156
To program up to three devices:
Programming Universal Home Remote — Fixed Code Most garage door openers sold before 1996 are Fixed Code units. Programming a garage door opener involves time-sensitive actions, so read the entire procedure before you begin. If you do not follow these actions, the device will time out and you will have to repeat the procedure.
1. To verify if you have a Fixed Code garage door opener, remove the battery cover on your hand held transmitter supplied by the manufacturer of your garage door opener motor. If you see a row of dip switches similar to the graphic above, you have a Fixed Code garage door opener. If you do not see a row of dip switches, return to the previous section for Programming Universal Home Remote – Rolling Code.
157
Example of Eight Dip Switches with Two Positions
Example of Eight Dip Switches with Three Positions
Your panel of switches may not appear exactly as they do in the examples above, but they should be similar. The switch positions on your hand-held transmitter may be labeled, as follows: (cid:129) A switch in the up position may be labeled
as “Up,” “+,” or “On.”
(cid:129) A switch in the down position may be
labeled as “Down,” “−,” or “Off.”
(cid:129) A switch in the middle position may be
labeled as “Middle,” “0,” or “Neutral.”
158
2. Write down the eight to 12 switch settings
from left to right as follows: (cid:129) When a switch is in the up position,
write “Left.”
(cid:129) When a switch is in the down position,
write “Right.” If a switch is set between the up and down position, write “Middle.” The switch settings that you wrote down in Step 2 will now become the button strokes you enter into the Universal Home Remote in Step 4. Be sure to enter the switch settings that you wrote down in Step 2, in order from left to right, into the Universal Home Remote, when completing Step 4.
3. From inside your vehicle, first firmly press
all three buttons at the same time for about three seconds. Release the buttons to put the Universal Home Remote into programming mode.
4. The indicator lights will blink slowly. Enter each
switch setting from Step 2 into your vehicle’s Universal Home Remote. You will have two and one-half minutes to complete Step 4. Now press one button on the Universal Home Remote for each switch setting as follows:
If you wrote “Left,” press the left button in the vehicle. If you wrote “Right,” press the right button in the vehicle. If you wrote “Middle,” press the middle button in the vehicle.
159
(cid:129) (cid:129) (cid:129) (cid:129) 5. After entering all of the switch positions, again, firmly press and release all three buttons at the same time. The indicator lights will turn on.
6. Press and hold the button you would like to
use to control the garage door until the garage door moves. The indicator light above the selected button should slowly blink. You may need to hold the button from five to 55 seconds.
7. Immediately release the button when the
garage door moves. The indicator light will blink rapidly until programming is complete.
8. Press and release the same button again. The garage door should move, confirming that programming is successful and complete. To program another Fixed Code device such as an additional garage door opener, a security device, or home automation device, repeat Steps 1-8, choosing a different button in Step 6 than what you used for the garage door opener. Using Universal Home Remote Press and hold the appropriate button for at least half of a second. The indicator light will come on while the signal is being transmitted.
160
Reprogramming Universal Home Remote Buttons You can reprogram any of the three buttons by repeating the instructions. Erasing Universal Home Remote Buttons You should erase the programmed buttons when you sell or terminate your lease. To erase either Rolling Code or Fixed Code on the Universal Home Remote device: 1. Press and hold the two outside buttons at the same time for approximately 20 seconds, until the indicator lights, located directly above the buttons, begin to blink rapidly.
2. Once the indicator lights begin to blink,
release both buttons. The codes from all buttons will be erased.
For help or information on the Universal Home Remote System, call the customer assistance phone number under Customer Assistance Offices on page 508.
Storage Areas
Center Console Storage Area
Glove Box To open, lift the handle up. Use the key to lock and unlock.
Cupholder(s) There are two cupholders, with removable liners, located in front of the center console. There are cupholders located in the second row seat armrest. To access, pull the armrest down. There are additional cupholders located on each side of the third row seat and in each door. There are cupholders located behind the center console. To access, pull down on the handle.
Instrument Panel Storage Area Your vehicle has an instrument panel storage area located above the radio. To open the cover, press the button.
The armrest on the center console can slide forwards and backwards by holding up the lever located on the front of it. To open the armrest storage area, press the button located on the front of the armrest. There is additional storage under the armrest. Move the armrest all the way to the rear position. The tray can be removed for additional storage.
161
Floor Mats There is a grommet in the driver side floor mat that attaches to a hook on the floor of the vehicle. This allows the mat to remain in position under your feet and out of reach of the accelerator and brake pedal. To remove the floor mat, pull the mat towards the rear of the vehicle until the grommet can be removed from the hook. Make sure that the driver side floor mat is properly placed on the floor so that it does not block the movement of the accelerator and brake pedal.
Luggage Carrier
{CAUTION:
If you try to carry something on top of your vehicle that is longer or wider than the luggage carrier — like paneling, plywood, a mattress and so forth — the wind can catch it as you drive along. This can cause you to lose control. What you are carrying could be violently torn off, and this could cause you or other drivers to have a collision, and of course damage your vehicle. You may be able to carry something like this inside. But, never carry something longer or wider than the luggage carrier on top of your vehicle.
If you have the luggage carrier, you can load things on top of your vehicle. Crossrails are not standard on this vehicle and must be purchased at your dealer/retailer.
162
Notice: Loading cargo on the luggage carrier that weighs more than 200 lbs (91 kg) or hangs over the rear or sides of the vehicle may damage your vehicle. Load cargo so that it rests as far forward as possible and against the side rails, making sure to fasten it securely. Do not exceed the maximum vehicle capacity when loading your vehicle. For more information on vehicle capacity and loading, see Loading Your Vehicle on page 353. To prevent damage or loss of cargo as you are driving, check to make sure the cargo is still securely fastened.
Rear Seat Armrest Your vehicle may have a rear seat armrest that contains two cupholders. To access the cupholders, pull the armrest down from the rear seatback.
Convenience Net Your vehicle may have a convenience net. The convenience net is designed to help keep small loads, like grocery bags, from falling over. It is not designed to hold larger, heavier loads. To install the convenience net, attach both the upper and lower hooks to the loops on either side of the liftgate opening.
Cargo Cover Your vehicle may have a cargo cover. It can be used to cover items in the rear of the vehicle. To install the cover, place the loops found on each corner of the cover on the four hooks in the rear of the vehicle. When not in use, the cover can be stored in the cargo management system.
Cargo Tie Downs Your vehicle has eight cargo tie-downs located in the rear of the vehicle. These are used to secure small loads.
163
Cargo Management System Your vehicle has a cargo management system located in the rear of the vehicle. To open, pull the handle toward the rear of the vehicle and lift the cover up.
To remove the cargo management system: 1. Open the lid. 2. Remove the side panels and place inside
the bin.
3. Loosen the retaining nuts on each side of the
system by turning them counterclockwise.
4. Close the lid. 5. Pull up on the system by using the built in
handles and remove it from the vehicle.
There is an additional storage compartment on each side of the system. To open, unsnap and lift the panel up.
164
Sunroof The vehicle may have a sunroof over the front seats, and a rear sunroof over the second row seats. The rear sunroof does not open. The switches to operate the front sunroof and rear sunshade are located on the headliner above the rearview mirror. The ignition must be in ON or ACCESSORY to operate the sunroof. See Ignition Positions on page 124.
Express-open/Express-close: From the closed position, press and release the rear of the driver’s side switch to express-open the sunroof. Press and release the front of the driver’s side switch to express-close the sunroof. The front sunshade must be opened and closed manually. Push up on the sunshade handle to open the sunshade. Notice: The rear sunshade could be damaged if you attempt to open or close it manually. Do not manually open or close the rear sunshade. To open the rear sunshade, located over the second row seats, press and release the rear of the passenger’s side switch. Press and release the front of the switch to close the sunshade.
Vent: From the closed position, press and hold the front of the driver’s side switch to vent the sunroof. Press and hold the rear of the driver’s side switch to close the sunroof.
165
✍ NOTES
166
Section 3
Instrument Panel
Instrument Panel Overview ........................ 170
Hazard Warning Flashers .......................... 172
Other Warning Devices ............................. 172
Horn .......................................................... 172
Tilt and Telescopic Steering Wheel ............ 172
Power Tilt Wheel and TelescopicSteering Column .................................... 173
Turn Signal/Multifunction Lever .................. 174
Turn and Lane-Change Signals ................. 174
Headlamp High/Low-Beam Changer .......... 175
Flash-to-Pass ............................................ 176
Windshield Wipers ..................................... 176
Windshield Washer .................................... 177
Rear Window Wiper/Washer ...................... 178
Cruise Control ........................................... 179
Exterior Lamps .......................................... 182
Delayed Headlamps .................................. 183
Daytime Running Lamps (DRL)/Automatic Headlamp System .................. 183
Fog Lamps ................................................ 184
Instrument Panel Brightness ...................... 184
Courtesy Lamps ........................................ 184Dome Lamps ............................................. 185
Dome Lamp Override ................................ 185
Entry Lighting ............................................ 185
Delayed Entry Lighting .............................. 186
Delayed Exit Lighting ................................. 186
Parade Dimming ........................................ 186
Reading Lamps ......................................... 187
Electric Power Management ...................... 187
Battery Run-Down Protection ..................... 188
Ultrasonic Rear Parking Assist (URPA) ...... 188
Accessory Power Outlet(s) ........................ 192
Power Outlet 115 Volt AlternatingCurrent .................................................. 193
Climate Controls ......................................... 194
Climate Control System ............................. 194
Dual Automatic Climate Control System ..... 198
Outlet Adjustment ...................................... 205
Rear Air Conditioning andHeating System ...................................... 206
Rear Air Conditioning and Heating System
and Electronic Climate Controls ............... 207
167
Section 3
Instrument Panel
Malfunction Indicator Lamp ........................ 222
Oil Pressure Light ..................................... 225
Security Light ............................................ 226
Fog Lamp Light ......................................... 226
Cruise Control Light .................................. 226
Highbeam On Light ................................... 227
Tow/Haul Mode Light ................................ 227
Fuel Gage ................................................. 227
Driver Information Center (DIC) .................. 228DIC Operation and Displays
(With DIC Buttons) ................................. 229
DIC Operation and Displays
(Without DIC Buttons) ............................ 235
DIC Warnings and Messages .................... 239
DIC Vehicle Customization(With DIC Buttons) ................................. 250
Warning Lights, Gages, and Indicators ..... 209
Instrument Panel Cluster ........................... 210
Speedometer and Odometer ...................... 211
Tachometer ............................................... 211
Safety Belt Reminder Light ........................ 211
Passenger Safety Belt Reminder Light ....... 212
Airbag Readiness Light ............................. 212
Passenger Airbag Status Indicator ............. 214
Charging System Light .............................. 216
Voltmeter Gage ......................................... 216
Brake System Warning Light ..................... 217
Antilock Brake System Warning Light ........ 218
StabiliTrak® Indicator Light ......................... 219
Engine Coolant TemperatureWarning Light
........................................ 220
Engine Coolant Temperature Gage ............ 220
Tire Pressure Light .................................... 221168
Section 3
Instrument Panel
Audio System(s) ......................................... 260
Setting the Time ........................................ 261
Radio with CD ........................................... 263
Radio with CD and DVD ........................... 273
Using an MP3 (Radio with CD orSix-Disc CD Player) ............................... 290
Using an MP3 (Radio with CD and
DVD Player) ........................................... 296
XM Radio Messages ................................. 303Navigation/Radio System ........................... 305
Rear Seat Entertainment System ............... 305
Rear Seat Audio (RSA) ............................. 315
Theft-Deterrent Feature ............................. 317
Audio Steering Wheel Controls .................. 317
Radio Reception ........................................ 318
Care of Your CDs and DVDs .................... 320
Care of the CD and DVD Player ............... 320
Multi-Band Antenna ................................... 320169
Instrument Panel Overview
170
The main components of your instrument panel are listed here:
A. Air Vent. See Outlet Adjustment on page 205. B. Multifunction Lever. See Turn
Signal/Multifunction Lever on page 174. Windshield Wipers. See Turn Signal/Multifunction Lever on page 174.
C. Instrument Panel Cluster. See Instrument Panel
Cluster on page 210.
D. Driver Information Center (DIC) Buttons. See Driver Information Center (DIC) on page 228. E. Storage Area. See Instrument Panel Storage
Area on page 161.
F. Audio System. See Audio System(s) on
page 260. Navigation/Radio System (If Equipped). See Navigation/Radio System on page 305.
G. Exterior Lamps Control. See Exterior Lamps
on page 182.
H. Hood Release. See Hood Release on
page 385.
I. Dome Lamp Override Button. See Dome Lamp
Override on page 185. Instrument Panel Brightness Control. See Instrument Panel Brightness on page 184.
J. Cruise Control Buttons. See Cruise Control
on page 179.
K. Tilt and Telescopic Steering Wheel. See Tilt and Telescopic Steering Wheel on page 172. Power Tilt Wheel and Telescopic Steering (If Equipped). See Power Tilt Wheel and Telescopic Steering Column on page 173.
L. Horn. See Horn on page 172. M. Audio Steering Wheel Control Buttons. See
Audio Steering Wheel Controls on page 317.
N. Hazard Warning Flasher Button. See
Hazard Warning Flashers on page 172.
O. Center Console Shift Lever. See “Console Shift
Lever” under Shifting Into Park (P) on page 134.
P. Traction Control System (TCS) Disable Button
(If Equipped). See StabiliTrak® System on page 329. Tow/Haul Selector Button (If Equipped). See Tow/Haul Mode on page 132. Power Liftgate Button (If Equipped). See Power Liftgate on page 110.
Q. Accessory Power Outlets. See Accessory
Power Outlet(s) on page 192.
171
R. Heated Seats Button. See Heated Seats on
page 12.
S. Dual Automatic Climate Controls. See Dual
Automatic Climate Control System on page 198.
T. Passenger Air Bag Status Indicator. See Passenger Sensing System on page 86. U. Glove Box. See Glove Box on page 161.
Hazard Warning Flashers The hazard warning flashers let you warn others. They also let police know you have a problem. The front and rear turn signal lamps will flash on and off.
The hazard warning flasher button is located in the center of the instrument panel, below the audio system.
The hazard warning flashers work no matter what position the key is in, and even if the key is not in the ignition.
172
Press the button to make the front and rear turn signal lamps flash on and off. Press the button again to turn the flashers off. When the hazard warning flashers are on, the turn signals will not work.
Other Warning Devices If you carry reflective triangles, you can set them up at the side of the road about 300 feet (100 m) behind your vehicle.
Horn Press near or on the horn symbols on the steering wheel pad to sound the horn.
Tilt and Telescopic Steering Wheel A tilt and telescope wheel lets you adjust the steering wheel before you drive. The steering wheel can be raised to the highest level to give your legs more room when you enter and exit the vehicle.
The lever that lets you tilt and telescope the steering wheel is located on the left side of the steering column.
Power Tilt Wheel and Telescopic Steering Column
If your vehicle has this feature, the power tilt wheel control is located on the left side of the steering column.
To tilt and telescope the steering wheel, pull down the lever. Then move the steering wheel up or down or backward or forward into a comfortable position. Pull the lever up to lock the steering wheel in place. Do not adjust the tilt and telescope lever while driving.
To operate the power tilt feature, push the control up and the steering wheel will tilt up. Push the control down and the steering wheel will go down. Push the control forward and the steering wheel moves toward the front of the vehicle. Push the control rearward and the steering wheel moves toward the rear of the vehicle.
173
Turn Signal/Multifunction Lever
The lever on the left side of the steering column includes the following: (cid:129) G Turn and Lane Change Signals. See
Turn and Lane-Change Signals on page 174. (cid:129) 2 Headlamp High/Low-Beam Changer. See
Headlamp High/Low-Beam Changer on page 175.
(cid:129) Flash-to-Pass. See Flash-to-Pass on
page 176.
(cid:129) N Windshield Wipers. See Windshield
Wipers on page 176.
174
(cid:129) LQ Windshield Washer. See Windshield
Washer on page 177.
(cid:129) 5Z Rear Wiper/Washer. See Rear Window
Wiper/Washer on page 178.
For information on the headlamps, see Exterior Lamps on page 182.
Turn and Lane-Change Signals The turn signal has two upward (for right) and two downward (for left) positions. These positions allow you to signal a turn or a lane change. To signal a turn, move the lever all the way up or down. When the turn is finished, the lever will return automatically.
An arrow on the instrument panel cluster will flash in the direction of the turn or lane change.
To signal a lane change, raise or lower the lever until the arrow starts to flash. Hold it there until you complete your lane change. The lever will return by itself when you release it. If you momentarily press and release the lever, the turn signal will flash three times. If the arrow flashes faster than normal as you signal a turn or a lane change, a signal bulb may be burned out and other drivers will not see your turn signal. If a bulb is burned out, replace it to help avoid an accident. If the arrows do not go on at all when you signal a turn, check for burned-out bulbs and then check the fuse. See Fuses and Circuit Breakers on page 476. Turn Signal On Chime If you leave either one of your turn signals on and drive more than 3/4 mile (1.2 km), a chime will sound to alert you.
Headlamp High/Low-Beam Changer To change the headlamps from low beam to high beam, push the turn signal/multifunction lever toward the front of the vehicle.
This light on the instrument panel cluster comes on if the high beam lamps are turned on while the ignition is on.
To change the headlamps from high beam to low beam, pull the turn signal lever toward the rear of the vehicle.
175
Flash-to-Pass With the turn signal lever in the low-beam position, pull the lever toward you momentarily to switch to high-beam (to signal that you are going to pass). If the headlamps are on, they will return to low-beam when the lever is released. This feature operates even when the headlamps are off.
Windshield Wipers Clear ice and snow from the wiper blades before using them. If they are frozen to the windshield, gently loosen or thaw them. Damaged wiper blades may not clear the windshield well, making it harder to see and drive safely. If the blades do become damaged, install new blades or blade inserts. For more information, see Windshield Wiper Blade Replacement on page 424. Heavy snow or ice can overload the wiper motor. A circuit breaker will stop the motor until it cools down. Clear away snow or ice to prevent an overload.
Turn the band with the wiper symbol to control the windshield wipers. 8 (Mist): Turn the band to mist for a single wiping cycle. Hold it there until the wipers start. Then let go. The wipers stop after one wipe. Hold the band on mist longer, for more wipe cycles. 9 (Off): To stop the wipers, move the band to off.
6 (Delay): Turn the band to adjust the delay time. The delay between wiping cycles becomes shorter as the band is moved to the top of the lever. This can be very useful in light rain or snow. 6 (Low Speed): Turn the band away from you to the first solid band past the delay settings, for steady wiping at low speed.
? (High Speed): Turn the band further, to the second solid band past the delay settings, for high-speed wiping.
176
Windshield Washer
J (Washer Fluid): Press and release this paddle, located at the top of the turn signal/multifunction lever, to spray washer fluid on the windshield. The wipers clear the windshield and either stop or return to the preset speed. The ignition key must be in ACCESSORY or ON for this to work. See Windshield Washer Fluid on page 409 Windshield Washer Fluid.
{CAUTION:
In freezing weather, do not use your washer until the windshield is warmed. Otherwise the washer fluid can form ice on the windshield, blocking your vision.
WASHER FLUID LOW ADD FLUID is displayed on the Driver Information Center (DIC) when the washer fluid is low. See DIC Warnings and Messages on page 239.
Heated Windshield Washer If your vehicle has the heated windshield washer fluid system it can be used to help clear ice, snow, tree sap, or bugs from the windshield. This feature only works with the front wiper system, not the rear wiper system.
The button is located to the left of the steering column on the instrument panel.
Push the heated washer fluid button to activate the heated windshield washer fluid system. This activation begins four heated wash/wipe cycles. The first heated wash/wipe cycle can take up to 40 seconds to occur, depending on outside temperature. After the first wash/wipe cycle, it can take up to 20 seconds for each of the remaining cycles. Press the button again to turn off the heated windshield washer fluid system or it will automatically turn off after four wipe cycles have been completed.
177
When the heated windshield washer fluid system is activated under certain outside temperature conditions, steam might flow out of the washer nozzles for a short period of time before washer fluid is sprayed. This is a normal condition. WASHER FLUID LOW ADD FLUID is displayed on the DIC when the washer fluid is low. See DIC Warnings and Messages on page 239. Rear Window Wiper/Washer
{CAUTION:
In freezing weather, do not use your washer until the windshield is warmed. Otherwise the washer fluid can form ice on the windshield, blocking your vision.
The rear wiper control is located on the turn signal/multifunction lever. To turn the rear wiper on, slide the lever to a wiper position. 9(Off): Slide the lever to this setting to turn the wiper off.
5 (Rear Wiper Delay): Slide the lever to this setting to turn on the rear wiper delay.
Z (Rear Wiper): Slide the lever to this setting to turn on the rear wiper. = (Rear Wiper Wash): Push the button on the end of the turn signal/multifunction lever to spray washer fluid on the rear window. The wipers will clear the rear window and either stop or return to your preset speed. For more washer cycles, press and hold the button.
178
Cruise Control With cruise control, you can maintain a speed of about 25 mph (40 km/h) or more without keeping your foot on the accelerator. This can really help on long trips. Cruise control does not work at speeds below about 25 mph (40 km/h). When you apply your brakes, cruise control is turned off.
{CAUTION:
Cruise control can be dangerous where you cannot drive safely at a steady speed. So, do not use your cruise control on winding roads or in heavy traffic. Cruise control can be dangerous on slippery roads. On such roads, fast changes in tire traction can cause excessive wheel slip, and you could lose control. Do not use cruise control on slippery roads.
The cruise control buttons are located on left side of the steering wheel.
T (On/Off): Press this button to turn cruise control on and off. The indicator comes on when cruise control is on.
+ RES (Resume/Accelerate): Press this button to make the vehicle accelerate or resume to a previously set speed.
SET–: Press this button to set the speed or make the vehicle decelerate.
[ (Cancel): Press this button to cancel cruise control.
179
Resuming a Set Speed Suppose you set your cruise control at a desired speed and then you apply the brake. This shuts off the cruise control. But you do not need to reset it. Once you are driving about 25 mph (40 km/h) or more, press the +RES button on your steering wheel. The vehicle will go back to the previously chosen speed and stay there. Increasing Speed While Using Cruise Control To increase the cruise speed while using cruise control: (cid:129) Press and hold the +RES button on the
steering wheel until you reach the desired speed, then release it.
(cid:129) To increase vehicle speed in small increments,
press the +RES button.
Setting Cruise Control Cruise control will not work if your parking brake is set, or if the master cylinder brake fluid level is low. The cruise control light on the instrument panel cluster comes on after the cruise control has been set to the desired speed.
{CAUTION:
If you leave your cruise control on when you are not using cruise, you might hit a button and go into cruise when you do not want to. You could be startled and even lose control. Keep the cruise control switch off until you want to use cruise control.
1. Press the cruise control on/off button. 2. Get up to the speed desired. 3. Press and release the SET– button located on
the steering wheel.
4. Take your foot off the accelerator.
180
Reducing Speed While Using Cruise Control To reduce your speed while using cruise control: (cid:129) Press and hold the SET– button on the
steering wheel until you reach the lower speed desired, then release it.
(cid:129) To slow down in very small amounts, press
the SET– button on the steering wheel briefly. Each time this is done, the vehicle will go about 1 mph (1.6 km/h) slower.
Passing Another Vehicle While Using Cruise Control Use the accelerator pedal to increase vehicle speed. When you take your foot off the pedal, your vehicle will slow down to the previously set cruise speed.
Using Cruise Control on Hills How well your cruise control will work on hills depends upon the vehicle speed, load, and the steepness of the hills. When going up steep hills, you might have to step on the accelerator pedal to maintain the vehicle speed. When going downhill, you might have to brake or shift to a lower gear to keep the vehicle speed down. Of course, applying the brake turns off the cruise control. Many drivers find this to be too much trouble and do not use cruise control on steep hills. Ending Cruise Control There are three ways to end cruise control: (cid:129) Step lightly on the brake pedal. (cid:129) Press the [ (cancel) button on the steering
(cid:129) Press the T (on/off) button on the steering
wheel.
wheel.
Erasing Speed Memory The cruise control set speed memory is erased by turning off the cruise control or the ignition.
181
Exterior Lamps
The exterior lamps control is located on the instrument panel to the left of the steering wheel.
It controls the following systems: (cid:129) Headlamps (cid:129) Taillamps (cid:129) Parking Lamps
License Plate Lamps Instrument Panel Lights (cid:129) Fog Lamps (if equipped) The exterior lamps control has four positions: O (Off): Briefly turn the control to this position to turn off the automatic light control. Briefly turn to this position again to turn automatic light control on again.
182
AUTO (Automatic): Turn the control to this position to automatically turn on the headlamps at normal brightness, together with the following: (cid:129) Parking Lamps (cid:129) Taillamps
License Plate Lamps Instrument Panel Lights
;(Parking Lamps): Turn the control to this position to turn on the parking lamps together with the following: (cid:129) Taillamps
License Plate Lamps Instrument Panel Lights
2(Headlamps): Turn the control to this position to turn on the headlamps together with the following lamps listed below. A warning chime will sound if you open the driver’s door when the ignition switch is off and the headlamps are on. (cid:129) Parking Lamps (cid:129) Taillamps
License Plate Lamps Instrument Panel Lights
(cid:129) (cid:129) (cid:129) (cid:129) (cid:129) (cid:129) (cid:129) (cid:129) -(Fog Lamps) (If your vehicle has them): Push the fog lamps control in to turn on the fog lamps. See Fog Lamps on page 184.
Delayed Headlamps The delayed headlamps feature provides a period of exterior lighting as you leave the area around your vehicle. The feature is activated when the headlamps are on due to the automatic headlamps control feature described previously in this section, and when the ignition is turned off. Your headlamps will then remain on until the exterior lamps control is moved to the parking lamps position or until the pre-selected delayed headlamp lighting period has ended. If you turn off the ignition with the headlamps switch in the parking lamps or headlamps position, the delayed headlamps cycle will not occur. To disable the delayed headlamps feature or change the time of delay, see DIC Vehicle Customization (With DIC Buttons) on page 250.
Daytime Running Lamps (DRL)/ Automatic Headlamp System Daytime Running Lamps (DRL) can make it easier for others to see the front of your vehicle during the day. DRL can be helpful in many different driving conditions, but they can be especially helpful in the short periods after dawn and before sunset. Fully functional daytime running lamps are required on all vehicles first sold in Canada. A light sensor on top of the instrument panel makes the DRL work, so be sure it is not covered. The DRL system’s automatic headlamp control will make the low-beam headlamps come on at a reduced brightness when the following conditions are met: (cid:129) The ignition is in the ON position. (cid:129) The exterior lamps control is in AUTO. (cid:129) The engine is running. When the DRL are on, only the low-beam headlamps, at a reduced level of brightness, will be on. The headlamps, taillamps, sidemarker, and other lamps will not be on. The instrument panel and cluster will also not be lit.
183
When it is dark enough outside, the low-beam headlamps will turn off and the headlamps and parking lamps will turn on. The other lamps that come on with the headlamps will also come on. When it is bright enough outside, the headlamps will go off and the DRL will come on. As with any vehicle, you should turn on the regular headlamp system when it is needed.
Fog Lamps
- (Fog Lamps): If your vehicle has fog lamps, the control is located on the exterior lamps control. The exterior lamps control is located on the instrument panel to the left of the steering column. The ignition must be in the ON position for the fog lamps to come on. To turn the fog lamps on, press the exterior lamps button. A light will come on in the instrument panel cluster. Press the exterior lamps button again to turn the fog lamps off.
When the headlamps are changed to high-beam, the fog lamps also go off. Some localities have laws that require the headlamps to be on along with the fog lamps.
Instrument Panel Brightness
D (Instrument Panel Brightness): The knob with this symbol on it is located next to the exterior lamps control. Push the knob in all the way until it extends out and then turn the knob clockwise to brighten or counterclockwise to dim the lights. Push the knob back in when finished.
Courtesy Lamps When a door is opened, the courtesy lamps automatically come on. They make it easy for you to enter and leave your vehicle. You can also manually turn these lamps on by fully turning the instrument panel brightness control clockwise. The reading lamps, located on the headliner above the rearview mirror, can be turned on or off independent of the automatic courtesy lamps, when the doors are closed.
184
Dome Lamps The dome lamps automatically come on when a door is opened, unless the dome lamp override button is pressed in. The lamps can also be turned on by turning the instrument panel brightness control clockwise to the farthest position. In this position, the dome lamps will remain on until they are turned off.
Dome Lamp Override The dome lamp override button is located next to the exterior lamps control. The dome lamp override is used to set the dome lamps to remain off or come on automatically when a door is opened. E(Dome Lamp Override): Press the button in and the dome lamps remain off when a door is opened. Press the button again to return it to the extended position so that the dome lamps come on when a door is opened.
Entry Lighting Your vehicle may have courtesy lamps that will come on and stay on for a set time whenever the unlock symbol is pressed on the Remote Keyless Entry (RKE) Transmitter, if the vehicle has one. If a door is opened, the lamps will stay on while it is open and then turn off automatically about 25 seconds after the door is closed. If the unlock symbol is pressed and you do not open a door, the lamps will turn off after about 20 seconds. Entry lighting includes a feature called theater dimming. With theater dimming, the lamps do not turn off at the end of the delay time. Instead, they slowly dim after the delay time until they go out. The delay time is canceled if you turn the ignition key to ON or press the power door lock switch. The lamps will dim right away. When the ignition is on, illuminated entry is inactive, which means the courtesy lamps will not come on unless a door is opened.
185
Delayed Entry Lighting Delayed entry lighting illuminates the interior for a period of time after all the doors have been closed. The ignition must be off for delayed entry lighting to work. Immediately after all the doors have been closed, the delayed entry lighting feature will continue to work until one of the following occurs: (cid:129) The ignition is in ON. (cid:129) The doors are locked. (cid:129) An illumination period of 25 seconds has
elapsed.
Delayed Exit Lighting This feature illuminates the interior for a period of time after the key is removed from the ignition. The ignition must be off for delayed exit lighting to work. When the key is removed, interior illumination will activate and remain on until one of the following occurs: (cid:129) The ignition is in ON. (cid:129) The power door locks are activated. (cid:129) An illumination period of 20 seconds has
elapsed.
If during the illumination period a door is opened, the timed illumination period will be canceled and the interior lamps will remain on because a door is open.
If during the illumination period a door is opened, the timed illumination period will be canceled and the interior lamps will remain on because a door is open.
Parade Dimming The instrument panel has an added feature called parade mode. It automatically prohibits the dimming of the instrument panel displays during the daylight while the headlamps are on so that you will still be able to see the displays.
186
Reading Lamps The vehicle has reading lamps that also act as the dome lamp. Press the button to turn them on and off.
Electric Power Management The vehicle has Electric Power Management (EPM) that estimates the battery’s temperature and state of charge. It then adjusts the voltage for best performance and extended life of the battery. When the battery’s state of charge is low, the voltage is raised slightly to quickly put the charge back in. When the state of charge is high, the voltage is lowered slightly to prevent overcharging. If the vehicle has a voltmeter gage or a voltage display on the Driver Information Center (DIC), you may see the voltage move up or down. This is normal. If there is a problem, an alert will be displayed. The battery can be discharged at idle if the electrical loads are very high. This is true for all vehicles. This is because the generator (alternator) may not be spinning fast enough at idle to produce all the power that is needed for very high electrical loads.
A high electrical load occurs when several of the following loads are on: headlamps, high beams, fog lamps, rear window defogger, climate control fan at high speed, heated seats, engine cooling fans, trailer loads, and loads plugged into accessory power outlets. EPM works to prevent excessive discharge of the battery. It does this by balancing the generator’s output and the vehicle’s electrical needs. It can increase engine idle speed to generate more power, whenever needed. It can temporarily reduce the power demands of some accessories. Normally, these actions occur in steps or levels, without being noticeable. In rare cases at the highest levels of corrective action, this action may be noticeable to the driver. If so, a Driver Information Center (DIC) message might be displayed, such as Battery Saver Active or Service Battery Charging System. If this message is displayed, it is recommended that the driver reduce the electrical loads as much as possible. See DIC Warnings and Messages on page 239.
187
Battery Run-Down Protection This vehicle has a feature to help prevent the battery from being drained, if the interior courtesy lamps, reading/map lamps, visor vanity lamps or trunk lamp are accidentally left on. If any of these lamps are left on, they will automatically turn off after 10 minutes, if the ignition is off. The lamps will not come back on again until one of the following occurs: (cid:129) The ignition is turned on. (cid:129) The exterior lamps control is turned off, then
on again.
The headlamps will timeout after 10 minutes, if they are manually turned on before the ignition is off.
Ultrasonic Rear Parking Assist (URPA) If your vehicle has the Ultrasonic Rear Parking Assist (URPA) system it is designed to help you park while in Reverse (R). It operates only at speeds less than 5 mph (8 km/h). URPA helps make parking easier and helps you avoid colliding with objects such as parked vehicles. The URPA system detects objects that are close to the rear of the vehicle which are at least 10 inches (25.4 cm) off the ground and below hood or trunk level. The system detects objects up to 8 feet (2.5 m) behind your vehicle. The URPA sensors determine how close these objects are from your bumper within this area.
188
{CAUTION:
The Ultrasonic Rear Park Assist (URPA) system does not replace driver vision. URPA does not:
(cid:129) Operate above speeds of 5 mph
(8 km/h).
(cid:129) Detect objects more than 8 feet
(2.5 meters) behind the vehicle. This distance may be less during warmer or humid weather.
(cid:129) Detect objects that are below the
bumper, underneath the vehicle, or that are very close to the vehicle.
(cid:129) Detect children, pedestrians,
bicyclists, or pets.
So if you do not use proper care before backing up, you could hit a vehicle, child, pedestrian, bicyclist, or pet, resulting in vehicle damage, injury, or death. Even though the vehicle has the URPA system, always check carefully before backing up by checking behind your vehicle.
The URPA display is located in the headliner and can be seen by looking over your right shoulder.
The URPA display has three color-coded lights. The lights are used to provide distance and system information, along with beeps that will be heard through the speakers. If the vehicle has a Driver Information Center (DIC), and PARK ASSIST OFF has been selected, then the vehicle is shifted into REVERSE (R), PARK ASSIST OFF will display on the DIC and one red light in the URPA display will be lit. See DIC Warnings and Messages on page 239 for more information. URPA automatically turns back on each time the vehicle is started.
189
How the System Works When the shift lever is moved into REVERSE (R), the rear display will briefly come on to let you know the display is operating correctly. URPA comes on automatically when the shift lever is moved into REVERSE (R). The system does not work at a reverse speed greater than 5 mph (8 km/h). To remind you of this, the red light on the rear display will flash. To disable URPA, see DIC Operation and Displays (With DIC Buttons) on page 229 or DIC Operation and Displays (Without DIC Buttons) on page 235
for more information.How the System Works when Backing If the shift lever is in REVERSE (R), URPA detects objects close to the rear bumper. The first time an object is detected a single beep will sound. If an object is detected at a REVERSE (R) speed between 0 mph (0 km/h) and 5 mph (8 km/h), the following describes what will occur based on your distance to a detected object located behind the vehicle: (cid:129) At distances between 40 inches (1 m) and
8 ft (2.5 m), a single amber light will come on. (cid:129) At distances between 23 inches (0.6 m) and 40 inches (1 m), both amber lights will be on. (cid:129) At distances between 12 inches (0.3 m) and
23 inches (0.6 m), all three lights (amber/ amber/red) will be on.
(cid:129) At distances less than 12 inches (0.3 m), a
beeping sound will repeat for a short time and all three lights (amber/amber/red) will flash. When the System Does Not Seem to Work Properly If the URPA system will not activate due to a temporary condition, the message PARK ASSIST OFF will display on the DIC screen and a red
190
light will come on the URPA display when the shift lever is moved into REVERSE (R). This occurs under the following conditions: (cid:129) The parking brake pedal is depressed. (cid:129) A trailer was attached to your vehicle, or a
bicycle or an object was hanging out of your trunk during your last drive when you turned off the vehicle. If the attached objects are removed from your vehicle before the start of your next drive, the system will return to normal operation unless an object is detected when the vehicle is shifted into REVERSE (R). If this occurs, URPA assumes the object is still attached, so you will have to wait until the vehicle is driven forward above 15 mph (25 km/h) before URPA will return to normal operation.
(cid:129) The ultrasonic sensors need to be kept clean. So, be sure to keep your vehicle’s rear bumper free of mud, dirt, snow, ice, and slush. For cleaning instructions, see Washing Your Vehicle on page 468. If the DIC still displays the PARK ASSIST OFF message after cleaning the bumper and driving forward at a speed of at least 15 mph (25 km/h), see your dealer/retailer.
(cid:129) Other conditions that may affect system
performance include vibrations from a jackhammer or the compression of air brakes on a very large truck or other mechanical devices that interfere with URPA performance. As always, drivers should use care when backing up a vehicle. Always look behind you, being sure to check for other vehicles, obstructions and blind spots. If the vehicle bumper is damaged, the URPA system may not work properly. Take the vehicle to your dealer/retailer to repair the system.
191
Notice: Adding any electrical equipment to your vehicle may damage it or keep other components from working as they should. The repairs would not be covered by your warranty. Do not use equipment exceeding maximum amperage rating of 20 amperes. Check with your dealer/retailer before adding electrical equipment. When adding electrical equipment, be sure to follow the installation instructions included with the equipment. Notice: Improper use of the power outlet can cause damage not covered by your warranty. Do not hang any type of accessory or accessory bracket from the plug because the power outlets are designed for accessory power plugs only.
Accessory Power Outlet(s) The accessory power outlets can be used to connect electrical equipment such as a cellular phone or CB radio. Your vehicle may have four accessory power outlets. They are located on the instrument panel below the climate controls, inside the front center console storage bin, at the rear of the center console, and in the rear cargo area. To use the outlets, remove the cover. When not in use, always cover the outlet with the protective cap. Notice: Leaving electrical equipment on for extended periods will drain the battery. Always turn off electrical equipment when not in use and do not plug in equipment that exceeds the maximum amperage rating of 20 amperes. Certain electrical accessories may not be compatible with the accessory power outlets and could result in blown vehicle or adapter fuses. If you experience a problem, see your dealer/retailer for additional information on the accessory power outlet.
192
Power Outlet 115 Volt Alternating Current Your vehicle may have a power outlet that can be used to plug in auxiliary electrical equipment with a maximum limit of 150 watts. If you try to use equipment that requires more than the limit, a protection circuit will cut the power supply. To reset the outlet, unplug the item and plug it back in or turn the ignition to LOCK or ACCESSORY and then back on. The power will automatically restart when equipment that operates within the limit is plugged into the outlet.
The power outlet is located on the rear of the center console.
The indicator on the inner outlet face will come on when 115 volt AC power is available. The AC power is available when the ignition is turned to ACCESSORY or ON, and electrical equipment is plugged into the outlet. The AC power is not available in the outlet when the ignition is turned to OFF. The power outlet is not designed for the following electrical equipment and may not work properly if these items are plugged into the power outlet: (cid:129) Equipment with high initial peak wattage such as: compressor-driven refrigerators and electric power tools.
(cid:129) Other equipment requiring an extremely stable
power supply such as: microcomputer-controlled electric blankets, touch sensor lamps, etc.
See High Voltage Devices and Wiring on page 475.
193
Temperature Control: Turn the center knob clockwise or counterclockwise to increase or decrease the temperature of the air flowing from the system.
Airflow Mode Control: Turn the right knob clockwise or counterclockwise to direct the airflow inside of the vehicle. To change the current mode, select one of the following: H (Vent): This mode directs air to the instrument panel outlets. ) (Bi-Level): This mode directs about half of the air to the instrument panel outlets and half to the floor outlets. A little air is directed towards the windshield and side window outlets. Cooler air is directed to the upper outlets and warmer air to the floor outlets.
Climate Controls Climate Control System With this system you can control the heating, cooling, defrost, defog, and ventilation of the vehicle.
Manual Operation 9 (Fan): Turn the left knob clockwise or counterclockwise to increase or decrease the fan speed. Turn the knob all the way counterclockwise to turn the front system off.
194
6 (Floor): This mode directs most of the air to the floor outlets, with some of the air directed to the windshield, side window outlets, and second row floor outlets. In this mode, the system automatically selects outside air. Recirculation cannot be selected when in Floor Mode. The right knob can also be used to select defog or defrost mode. For more information, see “Defogging and Defrosting” later in this section. By positioning the right knob between two modes, a combination of those two modes is selected. @ (Recirculation): Press this button to turn the recirculation mode on or off. The indicator light on the button turns on when this mode is selected. This mode keeps outside air from entering the vehicle. It can be used to reduce the outside air and odors entering the vehicle. Recirculation may also help cool the air inside the vehicle more quickly once the temperature inside the vehicle is less than the outside temperature.
The recirculation mode can be turned off in vent and bi-level modes by pressing the button again. Recirculation mode automatically turns off when the engine is turned off and must be re-selected when the engine is turned on again. The recirculation mode cannot be used with floor, defrost, or defogging modes. If you try to select recirculation in one of those modes, the indicator flashes three times and turns off. The air conditioning compressor also comes on when this mode is activated unless the outside air temperature is less than 40°F (4°C). While in
