Download PDF Manual

154 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 2. Place the handheld transmitter 1 to 3 in (3 to 8 cm) from the HomeLink威 buttons while keeping the EVIC display in view. For optimal training, point the battery end of the hand- held transmitter away from the HomeLink威 3. Simultaneously press and hold both the chosen HomeLink威 button and the handheld transmitter button until the EVIC display changes from “CHANNEL # TRAINING” to “CHANNEL # TRAINED”. Then release both the HomeLink威 and handheld trans- mitter buttons. If the EVIC display states “DID NOT TRAIN” repeat Step 3. If the signal is too weak, replace the battery in the handheld transmitter. It may take up to 30 seconds or longer in rare cases. The garage door may open and close while you train.


NOTE: Some gate operators and garage door openers may require you to replace Step 3 with procedures noted in the “Gate Operator/Canadian Programming” section. 4. Press and hold the just-trained HomeLink威 button. If the channel has been trained, the EVIC display will now state “CHANNEL # TRANSMIT”. If the EVIC display still states “CHANNEL # TRAIN- ING” repeat Step 3. NOTE: After training a HomeLink威 channel, if the garage door does not operate with HomeLink威 and the garage door opener was manufactured after 1995, the garage door opener may have rolling code. If so, proceed to Step 5. 5. Programming A Rolling Code System At the garage door opener motor (in the garage), locate the “Learn” or “Training” button.


This can usually be found where the hanging antenna wire is attached to the garage door opener motor (it is NOT the button normally used to open and close the door).


1 — Garage Door Opener 2 — Training Button


UNDERSTANDING THE FEATURES OF YOUR VEHICLE 155
6. Firmly press and release the LEARN or TRAINING button. The name and color of the button may vary by manufacturer. NOTE: You have 30 seconds in which to initiate the next step after the LEARN button has been pressed. 7. Return to the vehicle and press the programmed HomeLink威 button twice (holding the button for two seconds each time). If the device is plugged in and activates, programming is complete. If the device does not activate, press the button a third time (for two seconds) to complete the training. If you have any problems, or require assistance, please call toll-free 1–800–355–3515 or, on the Internet at www.HomeLink.com for information or assistance. To program the remaining two HomeLink威 buttons, repeat each step for each remaining button. DO NOT erase the channels.


156 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Gate Operator/Canadian Programming Canadian radio-frequency laws require transmitter sig- nals to “time-out” (or quit) after several seconds of transmission – which may not be long enough for HomeLink威 to pick up the signal during programming. Similar to this Canadian law, some U.S. gate operators are designed to “time-out” in the same manner. It may be helpful to unplug the device during the cycling process to prevent possible overheating of the garage door or gate motor. If you are having difficulties programming a garage door opener or a gate operator, replace “Programming HomeLink” Step 3 with the following: 3. Continue to press and hold the HomeLink威 button, while you press and release (“cycle”), your handheld transmitter every two seconds until HomeLink威 has


successfully accepted the frequency signal. The EVIC display will change from “CHANNEL # TRAINING” to “CHANNEL # TRAINED.” If you unplugged the device for training, plug it back in at this time. Then proceed with Step 4 under “Programming HomeLink威” earlier in this section. Using HomeLink姞 To operate, press the programmed HomeLink威 button. Activation will now occur for the trained device (i.e., garage door opener, gate operator, security system, entry door lock, home/office lighting, etc.,). The handheld transmitter of the device may also be used at any time.


and release


Reprogramming A Single HomeLink姞 Button To reprogram a channel that has been previously trained, follow these steps: 1. Turn the ignition switch to the ON/RUN position. 2. Press and hold the desired HomeLink威 button for 20 seconds until the EVIC display states “CHANNEL # TRAINING.” Do not release the button. 3. Without releasing the button, proceed with Program- ming HomeLink威 Step 2 and follow all remaining steps. Security It is advised to erase all channels before you sell or turn in your vehicle. To do this, press and hold the two outside buttons for 20 seconds until the EVIC message states “CHANNELS CLEARED.” Note that all channels will be erased. Indi- vidual channels cannot be erased.


UNDERSTANDING THE FEATURES OF YOUR VEHICLE 157
The HomeLink威 Universal Transceiver is disabled when the Vehicle Security Alarm is active. Troubleshooting Tips If you are having trouble programming HomeLink威, here are some of the most common solutions: • Replace the battery in the original transmitter. • Press the LEARN button on the garage door opener to • Did you unplug the device for training, and remember


complete the training for rolling code.


to plug it back in?


If you are having any problems or require assistance, please call toll-free 1–800–355–3515 or, on the Internet at www.HomeLink.com for information or assistance.


158 UNDERSTANDING THE FEATURES OF YOUR VEHICLE General Information This device complies with FCC rules Part 15 and Industry Canada RSS-210. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference that may be received including interference that may cause undesired operation. NOTE: The transmitter has been tested and it complies with FCC and IC rules. Changes or modifications not expressly approved by the party responsible for compli- ance could void the user’s authority to operate the device. The term “IC:” before the certification/registration num- ber only signifies that Industry Canada technical specifi- cations were met.


POWER SUNROOF — IF EQUIPPED The power sunroof switch is located on the overhead console between the courtesy/reading lights.


Power Sunroof Switch


WARNING!


• Never leave children alone in a vehicle. Leaving unattended children in a vehicle is dangerous for a number of reasons. A child or others could be seriously or fatally injured. do not leave the key in the ignition. A child could operate power win- dows, other controls, or move the vehicle. • In a collision, there is a greater risk of being thrown from a vehicle with an open sunroof. You could also be seriously injured or killed. Always fasten your seat belt properly and make sure all passengers are properly secured too. • Do not allow small children to operate the sun- roof. Never allow your fingers, other body parts, or any object to project through the sunroof opening. Injury may result.


UNDERSTANDING THE FEATURES OF YOUR VEHICLE 159


Open Sunroof — Express Mode Press the switch rearward and release it within one-half second and the sunroof will open automatically from any position. The sunroof will open fully and stop automati- cally. This is called “Express Open”. During Express Open operation, any movement of the sunroof switch will stop the sunroof. Opening Sunroof — Manual Mode To open the sunroof, press and hold the switch rearward to full open. Any release of the switch will stop the movement and the sunroof will remain in a partially opened condition until the switch is pushed and held rearward again. Closing Sunroof — Express Press the switch forward and release it within one-half second and the sunroof will close automatically from any


160 UNDERSTANDING THE FEATURES OF YOUR VEHICLE position. The sunroof will close fully and stop automati- cally. This is called “Express Close”. During Express Close operation, any movement of the switch will stop the sunroof. Closing Sunroof — Manual Mode To close the sunroof, press and hold the switch in the forward position. Any release of the switch will stop the movement and the sunroof will remain in a partially closed condition until the switch is pushed and held forward again. Pinch Protect Feature This feature will detect an obstruction in the opening of the sunroof during Express Close operation. If an ob- struction is detected, the sunroof will automatically re- tract. Remove the obstruction if this occurs. Next, press the switch forward and release to Express Close.


If three consecutive sunroof close attempts re- NOTE: sult in Pinch Protect reversals, the fourth close attempt will be a Manual Close movement with Pinch Protect disabled. Pinch Protect Override If a known obstruction (ice, debris, etc.) prevents closing the sunroof, press the switch forward and hold for two seconds after the reversal occurs. This allows the sunroof to move toward the closed position. NOTE: Pinch protection is disabled while the switch is pressed. Venting Sunroof — Express Press and release the “Vent” button, and the sunroof will open to the vent position. This is called “Express Vent”, and will occur regardless of sunroof position. During Express Vent operation, any movement of the switch will stop the sunroof.


Sunshade Operation The sunshade can be opened manually. However, the sunshade will open automatically as the sunroof opens. NOTE: The sunshade cannot be closed if the sunroof is open. Wind Buffeting Wind buffeting can be described as the perception of pressure on the ears or a helicopter-type sound in the ears. Your vehicle may exhibit wind buffeting with the windows down, or the sunroof (if equipped) in certain open or partially open positions. This is a normal occur- rence and can be minimized. If the buffeting occurs with the rear windows open, open the front and rear windows together to minimize the buffeting. If the buffeting occurs with the sunroof open, adjust the sunroof opening to minimize the buffeting or open any window.


UNDERSTANDING THE FEATURES OF YOUR VEHICLE 161


Sunroof Maintenance Use only a nonabrasive cleaner and a soft cloth to clean the glass panel. Ignition Off Operation The power sunroof switches remain active for up to approximately ten minutes after the ignition switch has been turned OFF. Opening either front door will cancel this feature. For vehicles equipped with the EVIC, the power sunroof switch will remain active for up to approximately ten minutes after the ignition switch is turned to the LOCK position. Opening either front door will cancel this feature. The time is programmable. Refer to “Electronic Vehicle Information Center (EVIC)/Personal Settings (Customer-Programmable Features)” in “Understanding Your Instrument Panel” for further information.


162 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ELECTRICAL POWER OUTLETS The auxiliary 12 Volt (13 Amp) power outlets can provide power for in-cab accessories designed for use with the standard “cigar lighter” plug. The 12 Volt power outlets have a cap attached to the outlet indicating “12V DC”, together with either a key symbol or a battery symbol. A key symbol indicates that the key must be in the ON/RUN or ACC positions for the outlet to provide power. The battery symbol indicates that the outlet is connected to the battery, and can provide power at all times. NOTE: To ensure proper operation a MOPAR威 knob and element must be used.


CAUTION!


• Do not exceed the maximum power of 160 Watts (13 Amps) at 12 Volts. If the 160 Watt (13 Amp) power rating is exceeded the fuse protecting the system will need to be replaced. • Power outlets are designed for accessory plugs only. Do not insert any other object in the power outlets as this will damage the outlet and blow the fuse. Improper use of the power outlet can cause damage not covered by your warranty.


The auxiliary power outlets can be found in the following locations: • Lower left and lower right of the center stack — • Inside the top storage tray — with floor mounted


without floor mounted shifter.


shifter.


Power Outlet — Floor Shifter


UNDERSTANDING THE FEATURES OF YOUR VEHICLE 163


• Inside the upper lid of the center storage compartment


— if equipped.


Power Outlet — Upper Lid


164 UNDERSTANDING THE FEATURES OF YOUR VEHICLE


• Rear of the center console storage compartment —


Quad Cab威 or Crew Cab.


The key symbol indicates that this outlet can supply power when the key is in the ON/RUN or ACC posi- tions. All accessories connected to the outlet(s) should be removed or turned off when the vehicle is not in use to protect the battery against discharge.


Power Outlet — Rear Center Console


UNDERSTANDING THE FEATURES OF YOUR VEHICLE 165


WARNING!


To avoid serious injury or death: • Only devices designed for use in this type of outlet should be inserted into any 12 Volt outlet. • Do not touch with wet hands. • Close the lid when not in use and while driving • If this outlet is mishandled, it may cause an


the vehicle.


electric shock and failure.


Power Outlet Fuse Locations


1 — M7 Fuse 20 A Yellow Power Outlet Center Seat (Opt) or with Console Rear 2 — M6 Fuse 20 A Yellow Cigar Lighter Instrument Panel or with Console Front 3 — M36 Fuse 20 A Yellow Power Outlet Instrument Panel or with Console Center


166 UNDERSTANDING THE FEATURES OF YOUR VEHICLE


CAUTION!


• Many accessories that can be plugged in draw power from the vehicle’s battery, even when not in use (i.e., cellular phones, etc.). Eventually, if plugged in long enough, the vehicle’s battery will discharge sufficiently to degrade battery life and/or prevent the engine from starting. • Accessories that draw higher power (i.e., coolers, vacuum cleaners, lights, etc.), will discharge the battery even more quickly. Only use these inter- mittently and with greater caution. • After the use of high power draw accessories, or long periods of the vehicle not being started (with accessories still plugged in), the vehicle must be driven a sufficient length of time to allow the generator to recharge the vehicle’s battery.


CIGAR LIGHTER AND ASH RECEIVER — IF EQUIPPED A removable ash receiver and cigar lighter are available. For vehicles with a bench seat the cupholder tray can be used to hold the ash receiver.


Ash Receiver and Cigar Lighter (Bench Seat)


1 — Cigar Lighter 2 — Ash Receiver


For vehicles equipped with an optional floor shifter.


Optional Floor Shifter


1 — Cigar Lighter 2 — Ash Receiver


UNDERSTANDING THE FEATURES OF YOUR VEHICLE 167


POWER INVERTER — IF EQUIPPED A 115 Volt (150 Watts Maximum) outlet is located on the center stack of the instrument panel, to the right of the radio. This outlet can power cellular phones, electronics and other low power devices requiring power up to 150
Watts. Certain high-end video games, such as Playsta- tion3 and XBox360 will exceed this power limit, as will most power tools. The power inverter is designed with built-in overload protection. If the power rating of 150 Watts is exceeded, the power inverter will automatically shut down. Once the electrical device has been removed from the outlet the inverter should automatically reset. If the power rating exceeds approximately 170 Watts, the power inverter may have to be reset manually. To reset the inverter


168 UNDERSTANDING THE FEATURES OF YOUR VEHICLE manually press the power inverter button OFF and ON. To avoid overloading the circuit, check the power ratings on electrical devices prior to using the inverter.


Power Inverter Outlet


The power inverter switch is located on the switch bank below the Climate Controls. To turn on the power outlet, press the switch once. Press the switch a second time to turn the power outlet off.


NOTE: • When the power inverter switch is pressed, there will be a delay of approximately one second before the power inverter status indicator turns on. The status indicator of the AC power inverter indicates whether the inverter is producing AC power. • Due to built-in overload protection, the power inverter


will shut down if the power rating is exceeded.


WARNING!


To avoid serious injury or death: • Do not use a three-prong adapter. • Do not insert any objects into the receptacles. • Do not touch with wet hands. • Close the lid when not in use. • If this outlet is mishandled it may cause an electric


shock and failure.


CUPHOLDERS


Front Instrument Panel Cupholders — (40–20–40
Seats) The cupholders are located in the pull-out tray at the bottom of the center stack. The pull-out tray must be secured when opened. To secure the tray push down until it “clicks”.


UNDERSTANDING THE FEATURES OF YOUR VEHICLE 169


Front Cupholders


170 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Front Instrument Panel Cupholders — Floor Mounted Shifter For vehicles equipped with bucket seats and a floor mounted shifter there are two cupholders located in the floor console.


Rear Cupholder — Quad Cab姞 Quad Cab威 vehicles may be equipped with a rear cup- holder that consists of two cup wells for rear passenger convenience.


Cupholders (Floor Mounted Shifter)


Rear Cup Wells


Rear Cupholder — Crew Cab Crew Cab vehicles are equipped with rear cupholders located in the center armrest.


UNDERSTANDING THE FEATURES OF YOUR VEHICLE 171


STORAGE Glove Box Storage The glove box is located on the passenger side of the instrument panel and features both an upper and lower storage area.


Crew Cab Rear Armrest Cupholder


1 — Upper Glove Box 2 — Lower Glove Box


Glove Box


172 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To open the upper glove box push upward on the handle release. The glove box door will automatically open.


To open the lower glove box, pull on the handle to release the latch and lower the door.


Upper Glove Box


Lower Glove Box


Door Storage


Front Door Storage — If Equipped Storage areas and bottle holders (drivers side only) are located in the door trim panels.


UNDERSTANDING THE FEATURES OF YOUR VEHICLE 173


Rear Door Storage — Crew Cab Storage compartments are located in both the driver and passenger door trim panels.


Front Door Storage


Rear Door Storage


174 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Center Storage Compartment — If Equipped The center storage compartment is located between the driver and passenger seats. The storage compartment provides an armrest and contains both and upper and lower storage area.


WARNING!


• This armrest is not a seat. Anyone seated on the armrest could be seriously injured during vehicle operation, or a collision. Only use the center seating position when the armrest is fully upright. • In a collision, the latch may open if the total weight of the items stored exceeds about 10 lbs (4.5 kg). These items could be thrown about en- dangering occupants of the vehicle. Items stored should not exceed a total of 10 lbs (4.5 kg).


Center Storage Compartment


Pull on the upper handle on the front of the armrest to raise the cover. The upper storage area contains a 12 Volt power outlet that can be used to power small electrical devices, refer to “Electrical Power Outlets” for further information.


UNDERSTANDING THE FEATURES OF YOUR VEHICLE 175
With the upper lid closed, pull on the lower handle to open the lower storage bin.


Upper Storage Compartment


Lower Storage Bin


176 UNDERSTANDING THE FEATURES OF YOUR VEHICLE


WARNING!


Do not operate this vehicle with a console compart- ment lid in the open position. Cellular phones, music players, and other handheld electronic devices should be stowed while driving. Use of these devices while driving can cause an accident due to distrac- tion, resulting in death or injury.


Second Row In-Floor Storage Bin — If Equipped In-floor storage bins are located in front of the second row seats and can be used for extra storage. The storage bins have removable liners that can be easily removed for cleaning.


In-Floor Storage Bin And Latch


To open in-floor storage bin, lift upward on the handle of the latch and open the lid.


NOTE: The front seat may have to be moved forward to fully open the lid.


UNDERSTANDING THE FEATURES OF YOUR VEHICLE 177


Seatback Storage Located in the back of both the driver and passenger front seats are pockets that can be used for storage.


Opened Storage Bin


Drivers Side Seatback Storage


178 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Storage (Regular Cab) The storage bin is located behind the front seats and runs the length of the cab.


Storage and Seats (Crew Cab) The Crew Cab models provide additional storage under the rear seats. Lift the seats to access the storage com- partment. To open the storage compartments, lift upward on the handle of the latch and open the lid.


Storage Bin


Crew Cab Storage


CAUTION!


Always lift the storage compartment lids by using the handle. Failure to lift the lids by using the handle can result in damage to the lids.


Plastic Grocery Bag Retainers (Regular Cab Models) Retainer hooks which will hold plastic grocery bag handles are built into the back panel of the cab, behind the rear seat.


UNDERSTANDING THE FEATURES OF YOUR VEHICLE 179


Grocery Bag Hooks


180 UNDERSTANDING THE FEATURES OF YOUR VEHICLE REAR WINDOW FEATURES


Rear Window Defroster


The rear window defroster button is located on the climate control panel. Press this button to turn on the rear window defroster and the heated outside mirrors (if equipped). An indicator in the button will illuminate when the rear window defroster is on. The rear window defroster automatically turns off after approximately 10 minutes. For an additional five minutes of operation, press the button a second time. NOTE: To prevent excessive battery drain, use the rear window defroster only when the engine is operating.


CAUTION!


Failure to follow these cautions can cause damage to the heating elements: • Use care when washing the inside of the rear window. Do not use abrasive window cleaners on the interior surface of the window. Use a soft cloth and a mild washing solution, wiping parallel to the heating elements. Labels can be peeled off after soaking with warm water. • Do not use scrapers, sharp instruments, or abra- sive window cleaners on the interior surface of the window. • Keep all objects a safe distance from the window.


Power Sliding Rear Window — If Equipped The switch for the power sliding rear window is located on the overhead console.


Rear Window Switch


Push the switch to the right to open the glass. Pull the switch to the left to close the glass.


UNDERSTANDING THE FEATURES OF YOUR VEHICLE 181


Manual Sliding Rear Window — If Equipped A locking device in the center of the window helps to prevent entry from the rear of the vehicle. Squeeze the lock to release the window.


FOLD FLAT LOAD FLOOR — IF EQUIPPED Quad Cab威 and Crew Cab models with a 60/40 rear seat may be equipped with a folding load floor.


WARNING!


Do not operate the vehicle with loose items stored on the load floor. While driving or in an accident you may experience abrupt stopping, rapid acceleration, or sharp turns. Loose objects stored on the load floor may move around with force and strike occupants, resulting in serious or fatal injury.


182 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Unfolding the Load Floor 1. Lift the 60/40 seat cushion(s) to the upward position.


Unfolding The Load Floor


2. Grasp the knob on the load floor and lift the knob until the load floor unfolds into position.


Load Floor In Open Position


3. Reverse the procedure to store the load floor. Positioning the Load Floor for Storage Access Under the Seat 1. Lift the 60/40 seat cushion(s) to the upward position.


2. Unsnap the securing snap located at either side of the load floor. 3. Lift the load floor up to access storage under the load floor.


WARNING!


Do not drive with the load floor in the up position. When stopping fast or in an accident, the load floor could move to the down position causing serious injury.


UNDERSTANDING THE FEATURES OF YOUR VEHICLE 183


Load Floor Securing Straps


4. Reverse the procedure to put the load floor back in the secured down position before you operate the vehicle.


184 UNDERSTANDING THE FEATURES OF YOUR VEHICLE RAMBOX姞 — IF EQUIPPED The RamBox威 system is an integrated pickup box storage and cargo management system consisting of three fea- tures: • Integrated box side storage bins • Cargo extender/divider • Bed rail tie-down system RamBox姞 Integrated Box Side Storage Bins Cargo storage bins are located on both sides of the pickup box. The cargo storage bins provide watertight, lockable, illuminated storage for up to 150 lbs (68 kg) of evenly distributed cargo.


RamBox威 Cargo Storage Bins


CAUTION!


Failure to follow the following items could cause damage to the vehicle: • Assure that all cargo inside the storage bins is • Do not exceed cargo weight rating of 150 lb (68 kg)


properly secured.


per bin.


To open a storage bin, press and release the button located on the lid. The RamBox威 lid will open upward to allow hand access. Lift the lid to fully open.


UNDERSTANDING THE FEATURES OF YOUR VEHICLE 185


RamBox威 Pushbutton And Lock


186 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The interior of the RamBox威 will automatically illumi- nate when the lid is opened. In addition to the automatic illumination switch, there is a manual on/off switch located at the rear of each storage bin. Pushing the switch once will turn off the bin lights, pushing the switch again will turn the lights back on.


RamBox威 Light Switch


CAUTION!


Leaving the lid open for extended periods of time could cause the vehicle battery to discharge. If the lid is required to stay open for extended periods of time, it is recommended that the bin lights be turned off manually using the on/off switch.


The RamBox威 storage bins can be locked using the vehicle key. To lock the storage bin, insert the key into the keyhole on the pushbutton and turn clockwise to lock.


CAUTION!


• Ensure cargo bin lids are closed and latched before


moving or driving vehicle.


(Continued)


CAUTION! (Continued)


• Loads applied to the top of the bin lid should be minimized to prevent damage to the lid and latching/hinging mechanisms. • Damage to the RamBox威 bin may occur due to heavy/sharp objects placed in bin that shift due to vehicle motion. In order to minimize potential for damage, secure all cargo to prevent movement and protect inside surfaces of bin from heavy/sharp objects with appropriate padding.


Cargo bins feature two removable drain plugs (to allow water to drain from bins). To remove plug, pull up on the edge. To install push plug downward into drain hole. NOTE: Provisions are provided in the bins for cargo dividers and shelf supports. These accessories (in addi- tion to other RamBox威 accessories) are available from MOPAR威.


UNDERSTANDING THE FEATURES OF YOUR VEHICLE 187


RamBox姞 Safety Warning Carefully follow these warnings to help prevent personal injury or damage to your vehicle:


WARNING!


vehicle is unattended.


• Always close the storage bin covers when your • Do not allow children to have access to the storage bins. Once in the storage bin, young children may not be able to escape. If trapped in the storage bin, children can die from suffocation or heat stroke. • In an accident, serious injury could result if the • Do not drive the vehicle with the storage bin • Keep the storage bin covers closed and latched • Do not use a storage bin latch as a tie down.


storage bin covers are not properly latched.


while the vehicle is in motion.


covers open.


188 UNDERSTANDING THE FEATURES OF YOUR VEHICLE RamBox威 Storage Bin Cover Emergency Release Lever — If Equipped As a security measure, a Storage Bin Cover Emergency Release is built into the storage bin cover latching mecha- nism.


Storage Bin Cover Emergency Release Lever


In the event of an individual being locked inside NOTE: the storage bin, the storage bin cover can be opened from inside of the bin by pulling on the glow-in-the-dark lever attached to the storage bin cover latching mechanism. Bed Extender — If Equipped The bed extender has three functional positions: • Storage Position • Divider Position • Extender Position Storage Position The storage position for the bed extender is at the front of the truck bed which maximizes the bed cargo area when not in use.


To install the bed extender into the storage position, perform the following: 1. Make sure the center handle is unlocked using the vehicle key and rotate the center handle vertically to release the extender side gates.


UNDERSTANDING THE FEATURES OF YOUR VEHICLE 189


Center Handle And Lock


1 — Center Handle Lock 2 — Handle


190 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 2. With the side gates open, position the extender fully forward in the bed against the front panel.


3. Rotate the side gates closed allowing the outboard ends to be positioned in front of the cargo tie down loops.


Storage Position


Cargo Tie Down Loop


4. Rotate the center handle horizontally to secure the side gates in the closed position.


UNDERSTANDING THE FEATURES OF YOUR VEHICLE 191


Divider Position The divider position is intended for managing your cargo and assisting in keeping cargo from moving around the bed. There are 11 divider slots along the bed inner panels which allow for various positions to assist in managing your cargo.


Side Gates Closed


5. Lock the center handle using the vehicle key to secure the panel into place and assist against theft.


192 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To install the bed extender into a divider position per- form the following: 1. Make sure the center handle is unlocked using the vehicle key and rotate the center handle vertically to release the extender side gates.


2. With the side gates open, position the extender so the outboard ends align with the intended slots in the sides of the bed.


Center Handle And Lock


1 — Center Handle Lock 2 — Handle


Aligning Gate To Slots


3. Rotate the side gates closed so that the outboard ends are secured into the intended slots of the bed.


4. Rotate the center handle horizontally to secure the side gates in the closed position.


UNDERSTANDING THE FEATURES OF YOUR VEHICLE 193


Extender Position The extender position allows you to load the bed of the truck beyond the tail gate. The bed extender will add an additional 15 in (38 cm) in the back of the truck when additional cargo room is needed. The extender position utilizes a locating pin and rotating handle located on both sides of the truck bed near the tailgate.


Side Gates Closed


5. Lock the center handle to secure the panel into place and assist against theft.


Extender Position


194 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To install the bed extender into the extender position perform the following: 1. Lower the tailgate. 2. Make sure the center handle is unlocked and rotate the center handle vertically in order to release the extender side gates. 3. Fit the end of the side gate ends onto the pin and handle.


Extender Installation


4. Rotate the handles to the horizontal position to secure into place.


WARNING!


UNDERSTANDING THE FEATURES OF YOUR VEHICLE 195


To reduce the risk of potential injury or property damage: • Cargo must be secured. • Do not exceed cargo load rating of your vehicle. • Secure all loads to truck utilizing cargo tie downs. • Extender should not be used as cargo tie down. • When vehicle is in motion do not exceed 150 lbs • The bed extender is not intended for off road use. • When not in use, the extender/divider should be in stowed or divider position with the tailgate closed. • When in use all handles are to be in the locked


(68 kg) load on the tailgate.


position.


Locking Tab


196 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Bed Rail Tie-Down System


CAUTION!


The maximum load per cleat should not exceed 250 lbs (113 kg) and the angle of the load on each cleat should not exceed 60 degrees above horizontal, or damage to the cleat or cleat rail may occur.


There are two adjustable cleats on each side of the bed that can be used to assist in securing cargo.


Adjustable Cleats


Each cleat must be located and tightened down in one of the detents, along either rail, in order to keep cargo properly secure. To move the cleat to any position on the rail, turn the nut counterclockwise, approximately three turns. Then pull


out on the cleat and slide it to the detent nearest the desired location. Make sure the cleat is seated in the detent and tighten the nut.


UNDERSTANDING THE FEATURES OF YOUR VEHICLE 197
To remove the cleats from the utility rail, remove the end cap by pushing up on the locking tab, located on the bottom of the end cap. Slide the cleat off the end of the rail.


1 — Utility Rail Detent 2 — Cleat Retainer Nut 3 — Utility Rail Cleat


Utility Rail End Cap


198 UNDERSTANDING THE FEATURES OF YOUR VEHICLE SLIDE-IN CAMPERS


Camper Applications Certain truck models are not recommended for slide-in campers. To determine if your vehicle is excluded, please refer to the “Consumer Information Truck-Camper Load- ing” document available from your authorized dealer. For safety reasons, follow all instructions in this impor- tant document. NOTE: When a cap or pickup camper is installed on a vehicle, an alternate Center High-Mounted Stop Light (CHMSL) must be provided.


EASY-OFF TAILGATE To simplify mounting of a camper unit with an overhang, the tailgate can be removed. If your vehicle is equipped with a rear camera NOTE: the electrical connector must be disconnected prior to removing the tailgate.


Disconnecting the Rear Camera — If Equipped


1. Open the tailgate to access the rear camera connector bracket located on the rear sill.


Connector Bracket


2. Remove the connector bracket from the sill by press- ing inward in the locking tab.


Locking Tab


3. Disconnect the chassis wiring harness, ensuring the connector bracket does not fall into the sill.


UNDERSTANDING THE FEATURES OF YOUR VEHICLE 199
4. Connect the chassis plug and bracket (provided in the glove box) to the chassis wiring harness and insert the bracket back into the sill. 5. Connect the tailgate plug (provided in the glove box) to the tailgate wiring harness to ensure that the terminals do not corrode. 6. Tape the tailgate harness and bracket against the forward-facing surface of the tailgate. This will prevent damaging the connector and bracket when storing or reinstalling the tailgate. Removing The Tailgate


1. Disconnect the wiring harness for the rear camera (if equipped), refer to “Disconnecting the Rear Camera — If Equipped” in this section. 2. Unlatch the tailgate and remove the support cables by releasing the lock tang from the pivot.


200 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: Make sure tailgate is supported when removing support cables.


Locking Tang


3. Raise the tailgate to a 45 degree angle. 4. Raise the right side of the tailgate until the right side pivot clears the hanger bracket.


5. Slide the entire tailgate to the right to free the left side pivot. 6. Remove the tailgate from the vehicle. NOTE: Do not carry the tailgate loose in the truck pickup box.


WARNING!


To avoid inhaling carbon monoxide, which is deadly, the exhaust system on vehicles equipped with “Cap or Slide-In Campers” should extend beyond the overhanging camper compartment and be free of leaks.


Locking Tailgate The lock is located next to the tailgate handle. The tailgate can be locked using the vehicle key.


UNDERSTANDING YOUR INSTRUMENT PANEL


CONTENTS


䡵 Instrument Panel Features . . . . . . . . . . . . . . . 205
䡵 Switch Bank Button Description . . . . . . . . . . . 206
▫ Upper Switch Bank . . . . . . . . . . . . . . . . . . . 206
▫ Lower Switch Bank . . . . . . . . . . . . . . . . . . . 207
䡵 Instrument Cluster — Base . . . . . . . . . . . . . . . 208
䡵 Instrument Cluster — Premium . . . . . . . . . . . 209
䡵 Instrument Cluster Descriptions . . . . . . . . . . . 210
䡵 Electronic Vehicle Information Center (EVIC) —


If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . 227


▫ EVIC Displays . . . . . . . . . . . . . . . . . . . . . . 229
▫ Fuel Economy / Fuel Saver Mode / Distance


To Empty (DTE) — If Equipped . . . . . . . . . . 235
. . . . . . . . . . . . . . . . . . . . . . 237


▫ Trip Functions ▫ Vehicle Info (Customer Information


Features)


. . . . . . . . . . . . . . . . . . . . . . . . . . 238
▫ Tire Psi . . . . . . . . . . . . . . . . . . . . . . . . . . . 238
▫ Units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 239
▫ Compass / Temperature Display . . . . . . . . . 240


202 UNDERSTANDING YOUR INSTRUMENT PANEL ▫ Customer-Programmable Features (System


Setup)


. . . . . . . . . . . . . . . . . . . . . . . . . . . . 242


䡵 Media Center 730N/430/430N (RHR/RER/


RBZ/RHB) CD/DVD/HDD/NAV — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . . . 249
▫ Operating Instructions (Voice Command


System) — If Equipped . . . . . . . . . . . . . . . . 249


▫ Operating Instructions (Uconnect™ Phone)


— If Equipped . . . . . . . . . . . . . . . . . . . . . . 249
䡵 Media Center 130 (Sales Code RES) . . . . . . . . . 249
▫ Operating Instructions — Radio Mode . . . . . 250
▫ Operation Instructions — CD Mode For CD


And MP3 Audio Play . . . . . . . . . . . . . . . . . 253
▫ Notes On Playing MP3 Files . . . . . . . . . . . . 255
▫ Operation Instructions - Auxiliary Mode . . . . 257


䡵 Media Center 130 With Satellite Radio (Sales


Code RES+RSC) . . . . . . . . . . . . . . . . . . . . . . . 258
▫ Operating Instructions — Radio Mode . . . . . 258
▫ Operation Instructions — CD Mode For CD


And MP3 Audio Play . . . . . . . . . . . . . . . . . 264
▫ Notes On Playing MP3 Files . . . . . . . . . . . . 266
▫ List Button (CD Mode For MP3 Play) . . . . . . 269
▫ Info Button (CD Mode For MP3 Play) . . . . . . 269
▫ Uconnect™ Multimedia (Satellite Radio) —


If Equipped . . . . . . . . . . . . . . . . . . . . . . . . 270


▫ Operating Instructions (Uconnect™ Phone)


— If Equipped . . . . . . . . . . . . . . . . . . . . . . 274
䡵 iPod威 Control — If Equipped . . . . . . . . . . . . . 274
▫ Connecting The iPod威 . . . . . . . . . . . . . . . . . 275


▫ Using This Feature . . . . . . . . . . . . . . . . . . . 276
▫ Controlling The iPod威 Using Radio


Buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . 276
▫ Play Mode . . . . . . . . . . . . . . . . . . . . . . . . . 276
▫ List Or Browse Mode . . . . . . . . . . . . . . . . . 278
䡵 iPod威/USB/MP3 Control — If Equipped . . . . . 280


▫ Connecting The iPod威 Or External USB


Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . 280
▫ Using This Feature . . . . . . . . . . . . . . . . . . . 281
▫ Controlling The iPod威 Or External USB


Device Using Radio Buttons . . . . . . . . . . . . . 282
▫ Play Mode . . . . . . . . . . . . . . . . . . . . . . . . . 282
▫ List Or Browse Mode . . . . . . . . . . . . . . . . . 283
▫ Bluetooth Streaming Audio (BTSA) . . . . . . . . 285


UNDERSTANDING YOUR INSTRUMENT PANEL 203


䡵 Video Entertainment System (VES)™ — If


Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . . . 286


䡵 Steering Wheel Audio Controls —


If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . 288
▫ Radio Operation . . . . . . . . . . . . . . . . . . . . . 289
▫ CD Player . . . . . . . . . . . . . . . . . . . . . . . . . 289
䡵 CD/DVD Disc Maintenance . . . . . . . . . . . . . . 290
䡵 Radio Operation And Mobile Phones . . . . . . . 290
䡵 Climate Controls . . . . . . . . . . . . . . . . . . . . . . 290


▫ Manual Heating And Air Conditioning


System . . . . . . . . . . . . . . . . . . . . . . . . . . . . 291


▫ Automatic Temperature Control (ATC) —


If Equipped . . . . . . . . . . . . . . . . . . . . . . . . 295
▫ Summer Operation . . . . . . . . . . . . . . . . . . . 300


204 UNDERSTANDING YOUR INSTRUMENT PANEL


▫ Winter Operation . . . . . . . . . . . . . . . . . . . . 300
▫ Vacation/Storage . . . . . . . . . . . . . . . . . . . . 301
▫ Window Fogging And Frosting . . . . . . . . . . 301


▫ Outside Air Intake . . . . . . . . . . . . . . . . . . . 301
▫ Operating Tips . . . . . . . . . . . . . . . . . . . . . . 302


INSTRUMENT PANEL FEATURES


UNDERSTANDING YOUR INSTRUMENT PANEL 205


1 — Headlight Switch 2 — Instrument Cluster 3 — Radio 4 — Upper Switch Bank 5 — Upper Glove Compartment 6 — Lower Glove Compartment


7 — 115v Power Inverter Outlet 8 — Power Outlet 9 — Lower Switch Bank 10 — Cup Holders 11 — Climate Controls 12 — Power Outlet/Cigar Lighter


13 — Transfer Case Position Switch 14 — Ignition Switch 15 — Hood Release 16 — Parking Brake Release


206 UNDERSTANDING YOUR INSTRUMENT PANEL SWITCH BANK BUTTON DESCRIPTION


Upper Switch Bank


The upper switch bank is located on the center of the instrument panel.


2. ESC OFF Refer to “Starting And Operating” for more information. 3. HAZARD WARNING FLASHER Refer to “What To Do In Emergencies” for more infor- mation. 4. 115V POWER INVERTER Refer to “Understanding The Features Of Your Vehicle” for more information. 5. REAR PARK ASSIST Refer to “Understanding The Features Of Your Vehicle” for more information. 6. TPMS LIGHT LOAD — IF EQUIPPED Refer to “Starting And Operating” for more information.


1. TOW/HAUL Refer to “Starting And Operating” for more information.


Lower Switch Bank


The lower switch bank is located on the center of the instrument panel.


UNDERSTANDING YOUR INSTRUMENT PANEL 207


2. VENTILATED SEATS Refer to “Understanding The Features Of Your Vehicle” for more information. 3. HEATED STEERING WHEEL Refer to “Understanding The Features Of Your Vehicle” for more information.


1. HEATED SEATS Refer to “Understanding The Features Of Your Vehicle” for more information.


208 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER — BASE


INSTRUMENT CLUSTER — PREMIUM


UNDERSTANDING YOUR INSTRUMENT PANEL 209


210 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER DESCRIPTIONS


1. Tachometer The tachometer indicates engine speed in Revolutions Per Minute (RPM x 1000).


CAUTION!


Do not operate the engine with the tachometer pointer at high RPM for extended periods. Engine damage may occur.


2. Turn Signal Indicators


The arrow will flash with the exterior turn signal when the turn signal lever is operated.


NOTE: • A continuous chime will sound if the vehicle is driven more than 1 mile (1.6 km) with either turn signal on.


• Check for an inoperative outside light bulb if either indicator remains on and does not flash, or flashes at a rapid rate. 3. Fuel Gauge Shows level of fuel in tank when ignition switch is in the ON/RUN position. 4. Temperature Gauge The temperature gauge shows engine coolant tempera- ture. Any reading within the normal range indicates that the engine cooling system is operating satisfactorily. The gauge pointer will likely indicate a higher tempera- ture when driving in hot weather, up mountain grades, or when towing a trailer. It should not be allowed to exceed the upper limits of the normal operating range.


CAUTION!


WARNING!


UNDERSTANDING YOUR INSTRUMENT PANEL 211


Driving with a hot engine cooling system could damage your vehicle. If the temperature gauge reads “H” pull over and stop the vehicle. Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range. If the pointer remains on the “H” and you hear continuous chimes, turn the engine off immediately and call an autho- rized dealership for service.


A hot engine cooling system is dangerous. You or others could be badly burned by steam or boiling coolant. You may want to call an authorized dealer- ship for service if your vehicle overheats. If you decide to look under the hood yourself, see “Main- taining Your Vehicle”. Follow the warnings under the Cooling System Pressure Cap paragraph.


5. Speedometer The speedometer shows the vehicle speed in miles per hour and/or kilometers per hour (mph/km/h). 6. 4 LOW


This light alerts the driver that the vehicle is in the four-wheel drive LOW mode. The front and rear driveshafts are mechanically locked to- gether forcing the front and rear wheels to


212 UNDERSTANDING YOUR INSTRUMENT PANEL rotate at the same speed. Low range provides a greater gear reduction ratio to provide increased torque at the wheels. For further information on four-wheel drive operation and proper use, refer to “Four-Wheel Drive Operation — If Equipped” in “Starting And Operating”. 7. Electronic Throttle Control (ETC) Light


This light informs you of a problem with the Electronic Throttle Control (ETC) system. The light will come on when the ignition is first turned to ON/RUN and remain on briefly as a bulb check. If the light does not come on during starting, have the system checked by an authorized dealer. If a problem is detected, the light will come on while the engine is running. Cycle the ignition key when the vehicle has completely stopped and the shift lever is placed in the PARK position, the light should turn off.


If the light remains lit with the engine running, your vehicle will usually be drivable; however, see an autho- rized dealer for service as soon as possible. If the light is flashing when the engine is running, immediate service is required and you may experience reduced performance, an elevated/rough idle or engine stall and your vehicle may require towing. For vehicles equipped with a premium cluster this indi- cator will display in the Electronic Vehicle Information Center (EVIC). Refer to ”Electronic Vehicle Information Center (EVIC) — If Equipped” for further information. 8. 4WD Indicator


This light indicates the vehicle is in four-wheel drive and 4LOCK. 4WD allows all four wheels to receive torque from the engine simultane- ously.


9. 4WD Auto Indicator


The 4WD auto indicator will be illuminated whenever the four-wheel drive mode is auto- matically engaged.


11. TOW/HAUL


The TOW HAUL button is located on the center stack upper switch bank. This light will illuminate when TOW HAUL mode is selected.


UNDERSTANDING YOUR INSTRUMENT PANEL 213


10. SVC (Service) 4WD


The SVC 4WD light monitors the electric shift four-wheel drive system. If the SVC 4WD light stays on or comes on during driving, it means that the four-wheel drive system is not func-


tioning properly and that service is required. For vehicles equipped with a premium cluster this indi- cator will display in the Electronic Vehicle Information Center (EVIC). Refer to ”Electronic Vehicle Information Center (EVIC) — If Equipped” for further information.


12. Electronic Stability Control (ESC) Activation/ Malfunction Indicator Light — If Equipped


The “ESC Activation/Malfunction Indicator Light” in the instrument cluster will come on when the ignition switch is turned to the ON/RUN position. It should go out with the engine running. If the “ESC Activation/Malfunction In- dicator Light” comes on continuously with the engine running, a malfunction has been detected in the ESC system. If this light remains on after several ignition cycles, and the vehicle has been driven several miles (kilometers) at speeds greater than 30 mph (48 km/h), see your authorized dealer as soon as possible to have the problem diagnosed and corrected.


214 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: • The “ESC Off


Indicator Light” and the “ESC Activation/Malfunction Indicator Light” come on mo- mentarily each time the ignition switch is turned to ON/RUN. • Each time the ignition is turned to ON/RUN, the ESC system will be ON, even if it was turned off previously. • The ESC system will make buzzing or clicking sounds when it is active. This is normal; the sounds will stop when ESC becomes inactive following the maneuver that caused the ESC activation.


13. Vehicle Security Light — If Equipped


This light will flash at a fast rate for approxi- mately 15 seconds, when the vehicle security alarm is arming, and then will flash slowly until the vehicle is disarmed.


14. Oil Pressure Gauge The pointer should always indicate some oil pressure when the engine is running. A continuous high or low reading under normal driving conditions may indicate a lubrication system malfunction. service Immediate should be obtained from an authorized dealer. 15. Odometer/Trip Odometer Button/ECO (Fuel Saver Indicator) Button — If Equipped Press this button to toggle between the odometer display, trip odometer display or the “ECO” display. Holding the button in resets the trip odometer reading when in trip mode. If equipped with Electronic Vehicle Information Center (EVIC) the “ECO” message will be displayed in the EVIC display in the instrument cluster. Refer to ”Electronic Vehicle Information Center (EVIC) — If Equipped” for further information.


16. Odometer Display / Electronic Vehicle Information Center (EVIC) Display Area — If Equipped


Odometer Display The odometer display shows the total distance the ve- hicle has been driven. U.S. Federal regulations require that upon transfer of vehicle ownership, the seller certify to the purchaser the correct mileage that the vehicle has been driven. If your odometer needs to be repaired or serviced, the repair technician should leave the odometer reading the same as it was before the repair or service. If s/he cannot do so, then the odometer must be set at zero, and a sticker must be placed in the door jamb stating what the mileage was before the repair or service. It is a good idea for you to make a record of the odometer reading before the repair/service, so that you can be sure that it is properly reset, or that the door jamb sticker is accurate if the odometer must be reset at zero.


UNDERSTANDING YOUR INSTRUMENT PANEL 215
The two trip odometers show individual trip mileage. To switch from odometer to trip odometers, press and release the TRIP ODOMETER button. To reset a trip odometer, display the desired trip odom- eter to be reset then push and hold the button for approximately two seconds until the display resets. Vehicle Odometer Messages When the appropriate conditions exist, the following messages will display in the odometer: ECO . . . . . . . . . . . . . . . . . . . Fuel Saver Indicator Off ECO-ON . . . . . . . . . . . . . . . . Fuel Saver Indicator On Lo tirE . . . . . . . . . . . . . . . . . . . . . . Low Tire Pressure noFUSE . . . . . . . . . . . . . . . . . . . . . . . . . . Fuse Fault CHAngE OIL . . . . . . . . . . . . . . . Oil Change Required LoWASH . . . . . . . . . . . . . . . . . . . . Low Washer Fluid NOTE: There is also an engine hour function. This indicates the total number of hours the engine has been running. To display the engine hours on the base cluster,


216 UNDERSTANDING YOUR INSTRUMENT PANEL perform the following: Place the ignition in the ON/ RUN, but do not start the engine. With the odometer value displayed, hold the TRIP button down for a period of six seconds. The odometer will change to trip value first, then it will display the engine hour value. The engine hours will be displayed for a period of 30 seconds until the ignition is turned OFF or the engine is started. If equipped, some of the above warnings will be dis- played in the Electronic Vehicle Information Center (EVIC) in the instrument cluster. Refer to ”Electronic Vehicle Information Center (EVIC) — If Equipped” for further information. ECO / ECO-ON (Fuel Saver Indicator) — If Equipped The ECO-ON indicator will illuminate when you are driving in a fuel efficient manner and can be used to modify driving habits in order to increase fuel economy. The ECO display will toggle between ECO and ECO-ON depending on driving habits and vehicle usage. Press the


Odometer / Trip Odometer / ECO (Fuel Saver Indicator) button to change the display from odometer to either of the two trip odometer settings or the “ECO” display.


If the vehicle diagnostic system determines that the fuel filler cap is loose, improperly installed, or damaged, a loose gascap indicator will display in the odometer display area. Tighten the fuel filler cap properly and press the TRIP button to turn off the message. If the problem continues, the message will appear


Loose Gascap Indicator


the next time the vehicle is started. A loose, improperly installed, or damaged fuel filler cap may also turn on the Malfunction Indicator Light (MIL). Lo tirE When the appropriate condition exists, the odometer display will toggle between Lo and tirE for three cycles.


noFUSE If the vehicle diagnostic system determines that the Ignition Off Draw (IOD) fuse is improperly installed, or damaged, a “noFUSE” message will display in the odom- eter display area. For further information on fuses and fuse locations refer to “Fuses” in “Maintaining Your Vehicle”. CHAngE OIL Your vehicle is equipped with an engine oil change indicator system. The CHAngE OIL message will flash in the instrument cluster odometer for approximately 12 seconds after a single chime has sounded to indicate the next scheduled oil change interval. The engine oil change indicator system is duty cycle-based, which means the engine oil change interval may fluctuate dependent upon your personal driving style. Unless reset, this message will continue to display each time you turn the ignition switch to the ON/RUN


UNDERSTANDING YOUR INSTRUMENT PANEL 217
position. To turn off the message temporarily, press and release the Trip Odometer button on the instrument cluster. To reset the oil change indicator system (after performing the scheduled maintenance), refer to the following procedure:


1. Turn the ignition switch to the ON/RUN position (do not start the engine). 2. Fully depress the accelerator pedal slowly three times within 10 seconds. 3. Turn the ignition switch to the OFF/LOCK position. If the indicator message illuminates when you NOTE: start the vehicle, the oil change indicator system did not reset. If necessary, repeat this procedure. 17. Engine Temperature Warning Light


This light warns of an overheated engine condi- tion. As temperatures rise and the gauge ap- proaches H, this indicator will illuminate and a


218 UNDERSTANDING YOUR INSTRUMENT PANEL single chime will sound after reaching a set threshold. Further overheating will cause the temperature gauge to pass H, the indicator will continuously flash and a continuous chime will occur until the engine is allowed to cool. If the light turns on while driving, safely pull over and stop the vehicle. If the A/C system is on, turn it off. Also, shift the transmission into NEUTRAL and idle the ve- hicle. If the temperature reading does not return to normal, turn the engine off immediately and call for service. Refer to “If Your Engine Overheats” in “What To Do In Emergencies” for further information. For vehicles equipped with a premium cluster this indi- cator will display in the Electronic Vehicle Information Center (EVIC). Refer to “Electronic Vehicle Information Center (EVIC) — If Equipped” for further information.


18. Shift Lever Indicator The Shift Lever Indicator is self-contained within the instrument cluster. It displays the gear position of the automatic transmission. In vehicles with 4.7L or 5.7L engines, the highest NOTE: available transmission gear is displayed in the lower right corner of the Electronic Vehicle Information Center (EVIC) whenever the Electronic Range Select (ERS) fea- ture is active. Use the +/- selector on the shift lever to activate ERS. Refer to “Automatic Transmission” in “Starting And Operating” for further information. 19. Low Fuel Light


When the fuel level reaches approximately 3.0 gal (11.0 L) this light will turn on, and remain on until fuel is added.


For vehicles equipped with a premium cluster this indi- cator will display in the Electronic Vehicle Information


Center (EVIC). Refer to ”Electronic Vehicle Information Center (EVIC) — If Equipped” for further information. 20. High Beam Indicator


This indicator shows that headlights are on high beam. Push the multifunction lever forward to switch the headlights to high beam, and pull toward yourself (normal position) to return to low beam. 21. Voltmeter When the engine is running, the gauge indicates the electrical system voltage. The pointer should stay within the normal range if the battery is charged. If the pointer moves to either extreme left or right and remains there during normal driving, the electrical system should be serviced. NOTE: The voltmeter may show a gauge fluctuation at various engine temperatures. This cycling operation is caused by the post-heat cycle of the intake manifold heater system. The number of cycles and the length of the


UNDERSTANDING YOUR INSTRUMENT PANEL 219
cycling operation is controlled by the engine control module. Post-heat operation can run for several minutes, and then the electrical system and voltmeter needle will stabilize. 22. Cargo Light


The cargo light will illuminate when the cargo light is activated by pressing the cargo light button on the headlight switch.


23. Brake Warning Light


This light monitors various brake functions, including brake fluid level and parking brake application. If the brake light turns on it may indicate that the parking brake is applied, that the brake fluid level is low, or that there is a problem with the Anti-lock Brake System reservoir. If the light remains on when the parking brake has been disengaged, and the fluid level is at the full mark on the


220 UNDERSTANDING YOUR INSTRUMENT PANEL master cylinder reservoir, it indicates a possible brake hydraulic system malfunction or that a problem with the Brake Booster has been detected by the Anti-Lock Brake System (ABS) / Electronic Stability Control (ESC) system. In this case, the light will remain on until the condition has been corrected. If the problem is related to the brake booster, the ABS pump will run when applying the brake and a brake pedal pulsation may be felt during each stop. The dual brake system provides a reserve braking capac- ity in the event of a failure to a portion of the hydraulic system. A leak in either half of the dual brake system is indicated by the Brake Warning Light, which will turn on when the brake fluid level in the master cylinder has dropped below a specified level. The light will remain on until the cause is corrected.


NOTE: The light may flash momentarily during sharp cornering maneuvers, which change fluid level condi- tions. The vehicle should have service performed, and the brake fluid level checked. If brake failure is indicated, immediate repair is neces- sary.


WARNING!


Driving a vehicle with the red brake light on is dangerous. Part of the brake system may have failed. It will take longer to stop the vehicle. You could have a collision. Have the vehicle checked immediately.


Vehicles equipped with the ABS, are also equipped with Electronic Brake Force Distribution (EBD). In the event of an EBD failure, the Brake Warning Light will turn on along with the ABS Light. Immediate repair to the ABS system is required.


Operation of the Brake Warning Light can be checked by turning the ignition switch from the OFF position to the ON/RUN position. The light should illuminate for ap- proximately two seconds. The light should then turn off unless the parking brake is applied or a brake fault is detected. If the light does not illuminate, have the light inspected by an authorized dealer. The light also will turn on when the parking brake is applied with the ignition switch in the ON/RUN posi- tion. NOTE: This light shows only that the parking brake is applied. It does not show the degree of brake application. 24. Oil Pressure Warning Light


This light indicates low engine oil pressure. The light should turn on momentarily when the engine is started. If the light turns on while driving, stop the vehicle and shut off the engine as soon as possible. A chime will sound for four minutes when this light turns on.


UNDERSTANDING YOUR INSTRUMENT PANEL 221
Do not operate the vehicle until the cause is corrected. This light does not indicate how much oil is in the engine. The engine oil level must be checked under the hood. For vehicles equipped with a premium cluster this indi- cator will display in the Electronic Vehicle Information Center (EVIC). Refer to ”Electronic Vehicle Information Center (EVIC) — If Equipped” for further information. 25. Tire Pressure Monitoring Telltale Light


Each tire, including the spare (if provided), should be checked monthly when cold and inflated to the inflation pressure recommended by the vehicle manufacturer on the vehicle placard or tire inflation pressure label. (If your vehicle has tires of a different size than the size indicated on the vehicle placard or tire inflation pressure label, you should determine the proper tire inflation pressure for those tires.)


222 UNDERSTANDING YOUR INSTRUMENT PANEL As an added safety feature, your vehicle has been equipped with a Tire Pressure Monitoring System (TPMS) that illuminates a low tire pressure telltale when one or more of your tires is significantly under-inflated. Accordingly, when the low tire pressure telltale illumi- nates, you should stop and check your tires as soon as possible, and inflate them to the proper pressure. Driving on a significantly under-inflated tire causes the tire to overheat and can lead to tire failure. Under-inflation also reduces fuel efficiency and tire tread life, and may affect the vehicle’s handling and stopping ability. Please note that the TPMS is not a substitute for proper tire maintenance, and it is the driver’s responsibility to maintain correct tire pressure, even if under-inflation has not reached the level to trigger illumination of the TPMS low tire pressure telltale. Your vehicle has also been equipped with a TPMS malfunction indicator to indicate when the system is not


operating properly. The TPMS malfunction indicator is combined with the low tire pressure telltale. When the system detects a malfunction, the telltale will flash for approximately one minute and then remain continuously illuminated. This sequence will continue upon subse- quent vehicle start-ups as long as the malfunction exists. When the malfunction indicator is illuminated, the sys- tem may not be able to detect or signal low tire pressure as intended. TPMS malfunctions may occur for a variety of reasons, including the installation of replacement or alternate tires or wheels on the vehicle that prevent the TPMS from functioning properly. Always check the TPMS malfunction telltale after replacing one or more tires or wheels on your vehicle, to ensure that the replacement or alternate tires and wheels allow the TPMS to continue to function properly.


CAUTION!


The TPMS has been optimized for the original equipment tires and wheels. TPMS pressures and warning have been established for the tire size equipped on your vehicle. Undesirable system opera- tion or sensor damage may result when using re- placement equipment that is not of the same size, type, and/or style. Aftermarket wheels can cause sensor damage. Do not use tire sealant from a can or balance beads if your vehicle is equipped with a TPMS, as damage to the sensors may result.


NOTE: The TPMS telltale is also accompanied by a “Low Tire” message in the odometer (Base Cluster), or in the Electronic Vehicle Information Center (EVIC) screen indicating “Low Tire” for EVIC enabled clusters.


UNDERSTANDING YOUR INSTRUMENT PANEL 223


26. Malfunction Indicator Light (MIL)


The Malfunction Indicator Light (MIL) is part of an onboard diagnostic (OBDII) system which monitors the emissions and engine control sys- tem. If the vehicle is ready for emissions testing, the light will come on when the ignition is first turned on and remain on, as a bulb check, until the engine is started. If the vehicle is not ready for emissions testing the light will come on when the ignition is first turned on and remain on for 15 seconds, then blink for 5 seconds, and remain on until the vehicle is started. If the bulb does not come on during starting, have the condition investigated promptly. If this light comes on and remains on while driving, it suggests a potential engine control problem and the need for system service.


224 UNDERSTANDING YOUR INSTRUMENT PANEL Although your vehicle will usually be drivable and not need towing, see your authorized dealer for service as soon as possible.


CAUTION!


Prolonged driving with the MIL on could cause damage to the engine control system. It also could affect fuel economy and drivability. If the MIL is flashing, severe catalytic converter damage and power loss will soon occur. Immediate service is required.


WARNING!


A malfunctioning catalytic converter, as referenced above, can reach higher temperatures than in normal operating conditions. This can cause a fire if you drive slowly or park over flammable substances such as dry plants, wood, cardboard, etc. This could result in death or serious injury to the driver, occupants or others.


27. Airbag Warning Light


This light will turn on for four to eight seconds as a bulb check when the ignition switch is first turned to ON/RUN. If the light is either not on during starting, stays on, or turns on while driving, have the system inspected at an authorized dealer as soon as possible. Refer to “Occupant Restraints” in “Things To Know Before Starting Your Vehicle” for further information.


28. Front Fog Light Indicator — If Equipped


This indicator will illuminate when the front fog lights are on.


29. Anti-Lock Brake (ABS) Light


This light monitors the Anti-lock Brake System (ABS). The light will turn on when the ignition switch is turned to the ON/RUN position and may stay on for as long as four seconds.


If the ABS light remains on or turns on while driving, it indicates that the anti-lock portion of the brake system is not functioning and that service is required. However, the conventional brake system will continue to operate normally if the BRAKE warning light is not on. If the ABS light is on, the brake system should be serviced as soon as possible to restore the benefits of anti-lock brakes. If the ABS light does not turn on when the ignition switch is turned to the ON/RUN position, have the light inspected by an authorized dealer.


UNDERSTANDING YOUR INSTRUMENT PANEL 225


30. Transmission Temperature Warning Light


This light indicates that there is excessive trans- mission fluid temperature that might occur with severe usage such as trailer towing. It may also occur when operating the vehicle in a high torque converter slip condition, such as 4-wheel-drive operation (e.g., snow plowing, off-road operation). If this light comes on, stop the vehicle and run the engine at idle or faster with the transmission in NEUTRAL until the light goes off.


CAUTION!


Continuous driving with the Transmission Tempera- ture Warning Light illuminated will eventually cause severe transmission damage or transmission failure.


226 UNDERSTANDING YOUR INSTRUMENT PANEL


WARNING!


If the Transmission Temperature Warning Light is illuminated and you continue operating the vehicle, in some circumstances you could cause the fluid to boil over, come in contact with hot engine or exhaust components and cause a fire.


For vehicles equipped with a premium cluster this warn- ing light will display in the Electronic Vehicle Informa- tion Center (EVIC). Refer to ”Electronic Vehicle Informa- tion Center further information. 31. Seat Belt Reminder Light


(EVIC) — If Equipped” for


When the ignition switch is first turned to ON/ RUN, this light will turn on for four to eight seconds as a bulb check. During the bulb check, if the driver’s seat belt is unbuckled, a chime will sound. After the bulb check or when driving, if the driver’s seat


belt remains unbuckled, the seat belt reminder light will flash or remain on continuously. Refer to “Occupant Restraints” in “Things To Know Before Starting Your Vehicle” for further information. 32. Charging System Light


This light shows the status of the electrical charg- ing system. The light should come on when the ignition switch is first turned to ON/RUN and remain on briefly as a bulb check. If the light stays on or comes on while driving, turn off some of the vehicle’s non-essential electrical devices or increase engine speed (if at idle). If the charging system light remains on, it means that the vehicle is experiencing a problem with the charging system. Obtain SERVICE IMMEDIATELY. See an autho- rized dealer. If jump starting is required, refer to “Jump Starting Procedures” in “What To Do In Emergencies”.


For vehicles equipped with a premium cluster this indi- cator will display in the Electronic Vehicle Information Center (EVIC). Refer to ”Electronic Vehicle Information Center (EVIC) — If Equipped” for further information. 33. Electronic Stability Control (ESC) OFF Indicator Light — If Equipped


This light indicates the Electronic Stability Con- trol (ESC) is off.


ELECTRONIC VEHICLE INFORMATION CENTER (EVIC) — IF EQUIPPED The Electronic Vehicle Information Center (EVIC) fea- tures a driver-interactive display that is located in the instrument cluster.


UNDERSTANDING YOUR INSTRUMENT PANEL 227


Electronic Vehicle Information Center (EVIC)


NOTE: • The compass on your vehicle is self-calibrating, elimi- nating the need to manually calibrate the compass. • The EVIC main menu will display Radio Off, AM/FM and SAT radio stations, and AUX/HDD sources at the top of the main menu above Fuel Economy.


228 UNDERSTANDING YOUR INSTRUMENT PANEL This system conveniently allows the driver to select a variety of useful information by pressing the switches mounted on the steering wheel. The EVIC consists of the following: • System Status display • Vehicle Information Warning Message Displays • Customer-Programmable Features (System Setup) • Compass Display • Outside Temperature Display • Trip Computer Functions • Fuel Economy display • Average Fuel Economy / Fuel Saver Mode display • Audio Modes display


Steering wheel EVIC control button, as it appears on the left side of the steer- ing wheel.


Press and release the UP button to scroll up- ward through the main menus (Fuel Economy, Vehicle Info, Tire PSI, Cruise, Messages, Units, System Setup) and sub-menus. Press and release the DOWN button to scroll downward through the main menus and sub- menus.


Steering wheel EVIC control button, as it appears on the right side of the steering wheel.


Press and release the SELECT button for access to main menus, sub-menus or to select a per- sonal setting in the system setup menu.


Press the BACK button to scroll back to a previous menu or sub-menu.


EVIC Displays When the appropriate conditions exist, the EVIC displays the following messages: • Left front turn signal lamp out


UNDERSTANDING YOUR INSTRUMENT PANEL 229


• Right front turn signal lamp out • Left rear turn signal lamp out • Right rear turn signal lamp out • Service air filter • Check Tire Pressure • Perform service • ESC Off • Service Tire Pressure System • Coolant Low • Check Trailer Brake Wiring • Service Trailer Brake System • Trailer Brake Connected • Trailer Brake Disconnected


motion)


230 UNDERSTANDING YOUR INSTRUMENT PANEL


• Lights On • Keyfob Battery Low • ECO (Fuel Saver Indicator) — If Equipped • Door(s) Ajar (with a single chime, if vehicle is in • Wrong Key • Damaged Key • Key not programmed • Key In Ignition • Turn Signal On • RKE Battery Low • LOW WASHER FLUID • Oil Change Due > Dealer Info


• Park Assist On • Park Assist Off • Warning Object Detected • Left Front Turn Signal Light Out • Left Rear Turn Signal Light Out • Right Front Turn Signal Light Out • Right Rear Turn Signal Light Out • Service Park Assist System • Park Assist System Blinded • Trailer Brake Disconnected — If Equipped • Personal Settings Not Available — Vehicle Not in Park • Remote start aborted — Door ajar • Remote start aborted — Hood ajar


• Remote start aborted — Fuel low • Remote start disabled — System fault • Remote start disabled — Turn key • Remote start active — Key to Run • Remote Start Disabled — Start Vehicle to Reset • Remote Start Active — Insert Key and Turn to RUN • Memory 1 Profile Set • Memory 2 Profile Set • Memory System Unavailable — Not in Park • Memory System Unavailable — Seatbelt Buckled • Memory 1 Profile Recall • Memory 2 Profile Recall • Adjustable Pedals Unavailable — Vehicle in Reverse


UNDERSTANDING YOUR INSTRUMENT PANEL 231


• Adjustable Pedals Unavailable — Cruise Engaged • To Tow Vehicle Safely, Read Neutral Shift Procedure in


Owners Manual


EVIC Warning Lights • Door Ajar


This light will turn on to indicate that one or more doors may be ajar.


• Oil Pressure Warning Light


This light indicates low engine oil pressure. The light should turn on momentarily when the engine is started. If the light turns on while driving, stop the vehicle and shut off the engine as soon as possible. A chime will sound for four minutes when this light turns on.


232 UNDERSTANDING YOUR INSTRUMENT PANEL Do not operate the vehicle until the cause is corrected. This light does not show how much oil is in the engine. The engine oil level must be checked under the hood. • Charging System Light


This light shows the status of the electrical charg- ing system. The light should come on when the ignition switch is first turned ON and remain on briefly as a bulb check. If the light stays on or comes on while driving, turn off some of the vehicle’s non-essential electrical devices or increase engine speed (if at idle). If the charging system light remains on, it means that the vehicle is experiencing a problem with the charging system. Obtain SERVICE IMMEDIATELY. See an autho- rized dealer. If jump starting is required, refer to “Jump Starting Procedures” in “What To Do In Emergencies”.


• Electronic Speed Control Light


This light will turn on when the electronic speed control is ON.


• Electronic Throttle Control (ETC) Light


This light informs you of a problem with the Electronic Throttle Control (ETC) system. The light will come on when the ignition is first turned ON and remain on briefly as a bulb check. If the light does not come on during starting, have the system checked by an authorized dealer. If a problem is detected, the light will come on while the engine is running. Cycle the ignition key when the vehicle has completely stopped and the shift lever is placed in the PARK position. The light should turn off.


If the light remains lit with the engine running, your vehicle will usually be drivable. However, see an autho- rized dealer for service as soon as possible. If the light is flashing when the engine is running, immediate service is required. You may experience reduced performance, an elevated/rough idle or engine stall and your vehicle may require towing. • Engine Temperature Warning Light


This light warns of an overheated engine condi- tion. As temperatures rise and the gauge ap- proaches H, this indicator will illuminate and a single chime will sound after reaching a set threshold. Further overheating will cause the temperature gauge to pass H, the indicator will continuously flash and a continuous chime will occur until the engine is allowed to cool. If the light turns on while driving, safely pull over and stop the vehicle. If the A/C system is on, turn it off. Also,


UNDERSTANDING YOUR INSTRUMENT PANEL 233
shift the transmission into NEUTRAL and idle the ve- hicle. If the temperature reading does not return to normal, turn the engine off immediately and call for service. Refer to “If Your Engine Overheats” in “What To Do In Emergencies” for more information. • SERV 4WD


The SERV 4WD light monitors the electric shift 4WD system. If the SERV 4WD light stays on or comes on during driving, it means that the 4WD system is not functioning properly and


that service is required. • Electronic Stability Control (ESC) OFF Indicator


Light — If Equipped


This light indicates the Electronic Stability Con- trol (ESC) is off.


234 UNDERSTANDING YOUR INSTRUMENT PANEL


• Transmission Temperature Light


This light indicates that there is excessive trans- mission fluid temperature that might occur with severe usage such as trailer towing. It may also occur when operating the vehicle in a high torque converter slip condition, such as 4-wheel-drive operation (e.g., snow plowing, off- road operation). If this light comes on, stop the vehicle and run the engine at idle or faster, with the transmission in NEUTRAL until the light goes off.


CAUTION!


Continuous driving with the Transmission Tempera- ture Indicator illuminated will eventually cause se- vere transmission damage or transmission failure.


WARNING!


If the Transmission Temperature Warning Light is illuminated and you continue operating the vehicle, in some circumstances you could cause the fluid to boil over, come in contact with hot engine or exhaust components and cause a fire. • Loose Gascap Indicator


If the vehicle diagnostic system determines that the fuel filler cap is loose, improperly installed, or damaged, a loose gascap indicator will display in the telltale display area. Tighten the fuel filler cap properly and press the SELECT button to turn off the message. If the problem continues, the message will appear the next time the vehicle is started. A loose, improperly installed, or damaged fuel filler cap may also turn on the Malfunction Indicator Light (MIL).


Oil Change Due Your vehicle is equipped with an engine oil change indicator system. The Oil Change Due message will flash in the EVIC display for approximately 10 seconds after a single chime has sounded to indicate the next scheduled oil change interval. The engine oil change indicator system is duty-cycle based, which means the engine oil change interval may fluctuate dependent upon your personal driving style. Unless reset, this message will continue to display each time you turn the ignition switch to the ON position. To turn off the message temporarily, press and release the RETURN button. To reset the oil change indicator system (after performing the scheduled maintenance), perform the following steps. 1. Turn the ignition switch to the ON position. (Do not start the engine)


UNDERSTANDING YOUR INSTRUMENT PANEL 235
2. Fully depress the accelerator pedal slowly three times within 10 seconds. 3. Turn the ignition switch to the OFF position. If the indicator message illuminates when you NOTE: start the engine, the oil change indicator system did not reset. If necessary, repeat these steps. Fuel Economy / Fuel Saver Mode / Distance To Empty (DTE) — If Equipped


Average Fuel Economy Shows the average fuel economy since the last reset. When the fuel economy is reset, the display will read “0” or show dashes for two seconds. Then, the history information will be erased, and the averaging will con- tinue from the last fuel average reading before the reset. Fuel Saver Mode The FUEL SAVER MODE message will display above the average fuel economy in the EVIC display. This message


236 UNDERSTANDING YOUR INSTRUMENT PANEL will appear whenever the Multi-Displacement System (MDS) (if equipped) allows the engine to operate on four cylinders, or if you are driving in a fuel efficient manner.


Fuel Saver Mode — On


This feature allows you to monitor when you are driving in a fuel efficient manner, and it can be used to modify driving habits in order to increase fuel economy.


Distance To Empty (DTE) Distance To Empty (DTE) Shows the estimated distance that can be traveled with the fuel remaining in the tank. This estimated distance is determined by a weighted average of the instantaneous and average fuel economy, according to the current fuel tank level. DTE cannot be reset through the RETURN button. NOTE: Significant changes in driving style or vehicle loading will greatly affect the actual drivable distance of the vehicle, regardless of the DTE displayed value. When the DTE value is less than 10 miles (16 km) estimated driving distance, the DTE display will change to a text display of ⬙LOW FUEL.⬙ This display will continue until the vehicle runs out of fuel. Adding a significant amount of fuel to the vehicle will turn off the ⬙LOW FUEL⬙ text and a new DTE value will display.


Trip Functions Press and release the ODOMETER/TRIP ODOMETER button until one of the following Trip Functions displays in the EVIC: • Trip A • Trip B • Elapsed Time Press the ODOMETER/TRIP ODOMETER button to cycle through all the Trip Computer functions. The Trip Functions mode displays the following informa- tion: • Trip A Shows the total distance traveled for Trip A since the last reset.


UNDERSTANDING YOUR INSTRUMENT PANEL 237


• Trip B Shows the total distance traveled for Trip B since the last reset. • Elapsed Time Shows the total elapsed time of travel since the last reset when the ignition switch is in the ACC position. Elapsed time will increment when the ignition switch is in the ON or START position. To Reset The Display Reset will only occur while a resettable function is being displayed. Press (for approximately two seconds) and release the ODOMETER/TRIP ODOMETER button once to clear the resettable function being displayed. To reset all the ODOMETER/TRIP ODOMETER button a second time within three seconds of resetting the currently-displayed function. (Reset ALL will display during this three- second window).


functions, press


and release


resettable


238 UNDERSTANDING YOUR INSTRUMENT PANEL Vehicle Info (Customer Information Features) Press and release the UP or DOWN button until “Vehicle Info” displays in the EVIC and press the SELECT button. Press the UP and DOWN button to scroll through the available information displays, then press SELECT to display any one of the following choices. • Coolant Temp Displays the actual coolant temperature. • Oil Temperature — If Equipped Displays the actual oil temperature. • Oil Pressure Displays the actual oil pressure. • Trans Temperature — If Equipped Displays the actual transmission temperature.


• Engine Hours Displays the number of hours of engine operation. • Trailer Brake — If Equipped Displays trailer brake output power and trailer brake status indicator. Tire PSI Press and release the UP or DOWN button until “Tire PSI” displays in the EVIC and press the SELECT button. This will display the Tire Pressure Monitor System (shows the current pressure of all four road tires). For additional information, refer to “Tire Pressure Monitor System” in “Starting And Operating”.


UNDERSTANDING YOUR INSTRUMENT PANEL 239
to “Tires-General Information/Tire Inflation Pres- sures” in “Starting And Operating” for additional information. • Your system can be set to display pressure units in PSI,


kPa, or BAR.


Units Press and release the UP or DOWN button until “Units” displays in the EVIC and press the SELECT button. The EVIC, odometer, and navigation system (if equipped) can be changed between English and Metric units of mea- sure. To make your selection, scroll up or down until the preferred setting is highlighted, then press and release the SELECT button until a check-mark appears next to the setting, showing that the setting has been selected.


Tire Pressure Display


NOTE: • Tires heat up during normal driving conditions. Heat will cause the tire pressure to increase from 2 to 6 psi (14 to 41 kPa) during normal driving conditions. Refer


Loading...
x