2006 Pontiac G6 Owners Manual

Download PDF Manual
2-1 Section 2 Features and Controls Mirrors ...........................................................2-39 Manual Rearview Mirror .................................2-39 Manual Rearview Mirror with OnStar® ..............2-39 Automatic Dimming Rearview Mirror with OnStar® and Compass ........................2-39 Automatic Dimming Rearview Mirror with Compass ...........................................2-41 Outside Power Mirrors ...................................2-43 Outside Convex Mirror ...................................2-43 OnStar® System .............................................2-44 Storage Areas ................................................2-45 Glove Box ...................................................2-45 Cupholder(s) ................................................2-45 Center Console Storage Area .........................2-45 Convenience Net ..........................................2-46 Sunroof .........................................................2-46 Sunroof - Panoramic .....................................2-47 Retractable Hardtop ........................................2-49 Lowering the Retractable Hardtop ...................2-49 Raising the Retractable Hardtop ......................2-51 2-2 Keys {CAUTION: Leaving children in a vehicle with the ignition key is dangerous for many reasons. They could operate the power windows or other controls or even make the vehicle move. The children or others could be badly injured or even killed. Do not leave the keys in a vehicle with children. 2-3 Remote Keyless Entry System If equipped, the keyless entry system operates on a radio frequency subject to Federal Communications Commission (FCC) Rules and with Industry Canada. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause interference. 2. This device must accept any interference received, including interference that may cause undesired operation of the device. This device complies with RSS-210 of Industry Canada. Operation is subject to the following two conditions: 1. This device may not cause interference. 2. This device must accept any interference received, including interference that may cause undesired operation of the device. Changes or modiﬁcations to this system by other than an authorized service facility could void authorization to use this equipment. One key is used for the ignition and all locks. When a new vehicle is delivered to the dealer, the key has a key tag. This tag has a bar-coded key code that tells your dealer how to make extra keys. This tag may be removed and kept by your dealer. If it hasn’t been removed, keep the tag in a safe place. If you lose your key, your dealer can easily make another one by using the key code. See Roadside Assistance Program on page 7-6 for more information. Notice: you may have to damage the vehicle to get in. Be sure you have spare keys. If you ever lock your keys in your vehicle, 2-4 Remote Keyless Entry System Operation The vehicle’s doors may be locked and unlocked, and the trunk can be opened from approximately 3 feet (1 m) up to 60 feet (18 m) away with the remote keyless entry transmitter. If your vehicle has the remote vehicle start feature, you can also start the vehicle’s engine with the remote keyless entry transmitter. At times you may notice a decrease in range. This is normal for any remote keyless entry system. If the transmitter does not work or if you have to stand closer to your vehicle for the transmitter to work, try this: (cid:127) Check the distance. You may be too far from your vehicle. You may need to stand closer during rainy or snowy weather. (cid:127) Check the location. Other vehicles or objects may be blocking the signal. Take a few steps to the left or right, hold the transmitter higher, and try again. (cid:127) Check to determine if battery replacement is necessary. See “Battery Replacement” under Remote Keyless Entry System Operation on page 2-5. If you are still having trouble, see your dealer or a qualiﬁed technician for service. Remote Keyless Entry with Remote Start Remote Keyless Entry without Remote Start 2-5 (cid:127) The following functions may be available if your vehicle has the remote keyless entry system. / (Remote Vehicle Start): If your vehicle has this feature, the engine may be started from outside the vehicle using the remote keyless entry transmitter. See “Remote Vehicle Start” later in this section for more detailed information. Q (Lock): Press the lock button to lock all the doors. The interior lamps will turn off after all of the doors are closed. If enabled through the Driver Information Center (DIC), the remote lock feedback can be programmed to have the horn chirp and/or the turn signals ﬂash when the remote keyless entry transmitter is used to lock the vehicle’s doors. See “LOCK HORN” and “LIGHT FLASH” under DIC Vehicle Personalization on page 3-52 for more information. Pressing the lock button may also arm the content theft-deterrent system. See Content Theft-Deterrent on page 2-19. K (Unlock): Press the unlock button to unlock the driver’s door. If the button is pressed again within ﬁve seconds, all remaining doors will unlock. The interior lamps will turn on and stay on for 20 seconds or until the ignition is turned on. If enabled through the DIC, the remote unlock feedback can be programmed to have the horn chirp and/or the turn signals ﬂash when 2-6 the remote keyless entry transmitter is used to unlock the vehicle’s doors. See “UNLOCK HORN” and “LIGHT FLASH” under DIC Vehicle Personalization on page 3-52 for more information. If enabled through the DIC, and it is dark enough outside, the vehicle’s high-beam headlamps, parking lamps, and back-up lamps will turn on each time the unlock button on the transmitter is pressed. These exterior lamps will stay on for 20 seconds, or until a door is opened. See “EXT (Exterior) LIGHTS” under DIC Vehicle Personalization on page 3-52 for additional information. Pressing the unlock button on the remote keyless entry transmitter will disarm the content theft-deterrent system. See Content Theft-Deterrent on page 2-19. V (Remote Trunk Release): The trunk will open when this button on the transmitter is pressed and held for approximately one second. You can open the trunk with the transmitter when the vehicle speed is less than 2 mph (3 km/h) or when the ignition is off. L (Vehicle Locator/Panic Alarm): This button may be used to locate your vehicle. Press and release this button to initiate vehicle locate. The horn will sound three times and the headlamps and turn signals will ﬂash three times. Press and hold the button for approximately three seconds to initiate the panic alarm. The horn will sound and the headlamps and turn signals will ﬂash for 30 seconds. Press the button again to cancel the panic alarm. Matching Transmitter(s) to Your Vehicle Each remote keyless entry transmitter is coded to prevent another transmitter from unlocking your vehicle. If a transmitter is lost or stolen, a replacement can be purchased through your dealer. Remember to bring any remaining transmitters with you when you go to your dealer. Each vehicle can have a maximum of four transmitters matched to it. Battery Replacement Under normal use, the battery in your remote keyless entry transmitter should last about four years. You can tell the battery is weak if the transmitter will not work at the normal range in any location. If you have to get close to your vehicle before the transmitter works, it is probably time to change the battery. The KEY FOB BATT LOW message in the vehicle’s DIC will display if the remote keyless entry transmitter battery is low. Notice: When replacing the battery, use care not to touch any of the circuitry. Static from your body transferred to these surfaces may damage the transmitter. To replace the battery in the remote keyless entry transmitter do the following: 1. Insert a ﬂat object, with a thin edge, into the notch located below the vehicle locator/panic alarm button, and separate the bottom half from the top half of the transmitter. 2. Remove the battery and replace it with the new one. Make sure the positive (+) side of the battery faces up. Use one three-volt, CR2032, or equivalent, type battery. 3. Put the two halves back together. Make sure the cover is on tight, so water will not get inside the transmitter. 4. Test the operation of the transmitter with the vehicle. 2-7 Remote Vehicle Start Your vehicle may have a remote starting feature. This feature allows you to start the engine from outside the vehicle. It may also start the vehicle’s heating or air conditioning systems and rear window defogger. When the remote start system is active and the vehicle has an automatic climate control system, it will automatically regulate the inside temperature. Normal operation of the system will return after the ignition key is turned to ON. Laws in some communities may restrict the use of remote starters. For example, some laws may require a person using remote start to have the vehicle in view when doing so. Check local regulations for any requirements on remote starting of vehicles. Do not use the remote start feature if your vehicle is low on fuel. Your vehicle may run out of fuel. The remote start feature provides two separate starts per ignition cycle, each with 10 minutes of engine running. The remote start feature needs to be reset after your vehicle’s engine is started two times using the transmitter’s remote start button. The remote start system is reset by inserting the vehicle’s key into the ignition switch and turning to ON. See Ignition Positions on page 2-23 for information regarding the ignition positions on your vehicle. 2-8 Your remote keyless entry transmitter, with the remote start button, provides an increased range of operation. You can start your vehicle’s engine from approximately 197 feet (60 m) away. However, the range may be less while the vehicle is running, and as a result you may need to be closer to your vehicle to turn it off than you were to turn it on. There are other conditions which can affect the performance of the transmitter, see Remote Keyless Entry System on page 2-4 for additional information. / (Remote Start): If your vehicle has the remote start feature, the keyless entry transmitter will have a button with this symbol on it. To start the vehicle using the remote start feature, do the following: 1. Aim the transmitter at the vehicle. 2. Press and release the transmitter’s lock button, then immediately press and hold the transmitter’s remote start button until the vehicle’s turn signal lamps ﬂash. 3. When the vehicle starts, the parking lamps will turn on and remain on while the engine is running. The engine will shut off automatically after 10 minutes, unless a time extension has been done or the vehicle’s key is inserted into the ignition switch and turned to ON. If you enter the vehicle after a remote start, and the engine is still running, insert the key into the ignition switch and turn to ON to drive the vehicle. 4. To manually shut off a remote start, do any of the following. The parking lamps will turn off to indicate the engine is off. (cid:127) Aim the remote keyless entry transmitter at the vehicle and press and release the remote start button. Turn on the hazard warning ﬂashers. Turn the ignition switch ON and then OFF. Your vehicle’s engine can be started two times, per ignition cycle, using the transmitter’s remote start feature. If only one remote start procedure has been done, since last driving the vehicle, or resetting the remote start system, the engine may be started again remotely by following the remote start procedure a second time. If the remote start procedure is used again before the ﬁrst 10 minute time frame has ended, 10 minutes will be added to the remaining time. The added 10 minutes are considered a second remote start. The remote vehicle start feature will not operate if any of the follow occur: The remote start system is disabled through the DIC. The vehicle’s key is in the ignition. The vehicle’s hood is open. The hazard warning ﬂashers are on. The check engine light is on. See Malfunction Indicator Lamp on page 3-40. The engine coolant temperature is too high. The oil pressure is low. Two remote vehicle starts have already been provided for that ignition cycle. Vehicles that have the remote vehicle start feature are shipped from the factory with the remote start system enabled. The system may be enabled or disabled through the DIC. See “REMOTE START” under DIC Vehicle Personalization on page 3-52 for additional information. 2-9 (cid:127) (cid:127) (cid:127) (cid:127) (cid:127) (cid:127) (cid:127) (cid:127) (cid:127) (cid:127) Remote Start Ready (Automatic Transmission Only) If your vehicle does not have the remote vehicle start feature, it may have the remote start ready feature. This feature allows your dealer to add the manufacturer’s remote vehicle start feature. If the keyless entry transmitter has a plus (+) symbol on the back cover, your vehicle has the remote start ready feature. You can lock or unlock your vehicle from approximately 197 feet (60 m) away. See your dealer if you would like to add the manufacturer’s remote vehicle start feature to your vehicle. 2-10 Doors and Locks Door Locks {CAUTION: Unlocked doors can be dangerous. (cid:127) Passengers — especially children — can easily open the doors and fall out of a moving vehicle. When a door is locked, the handle will not open it. You increase the chance of being thrown out of the vehicle in a crash if the doors are not locked. So, wear safety belts properly and lock the doors whenever you drive. (cid:127) Young children who get into unlocked vehicles may be unable to get out. A child can be overcome by extreme heat and can suffer permanent injuries or even death from heat stroke. Always lock your vehicle whenever you leave it. (cid:127) Outsiders can easily enter through an unlocked door when you slow down or stop your vehicle. Locking your doors can help prevent this from happening. There are several ways to lock and unlock your vehicle. From the outside, use your key or remote keyless entry transmitter, if equipped. Turn the key counterclockwise to unlock the door. Turn the key clockwise to lock the door. From the inside, use the manual lock knobs or the power lock switches. Power Door Locks The power door lock switches are located on the driver’s and front passenger’s door. Press the top of the switch to unlock all doors. Press the bottom of the switch to lock all doors. The rear doors do not have power door lock switches. Rear seat passengers must use the manual lock knob on their doors. Door Ajar Reminder If one of the doors is not fully closed while the ignition is on and the shift lever is moved out of PARK (P) or NEUTRAL (N) the following will occur: (cid:127) A chime will sound. The DOOR AJAR message will display through the Driver Information Center (DIC) until the door is closed. See DIC Warnings and Messages on page 3-48. 2-11 (cid:127) Delayed Locking This feature allows the driver to delay the locking of the vehicle. It will not operate with the key in the ignition. See Lockout Protection on page 2-13. Press the driver’s power door lock switch or the remote keyless entry transmitter lock button once. With the key removed from the ignition and the driver’s door open, the following will occur: Three chimes will sound to signal the delay. (cid:127) All doors will lock and the turn signals will ﬂash once ﬁve seconds after the last door has been closed. The horn will chirp if the horn chirp feature is enabled. See DIC Operation and Displays on page 3-46. If a door is opened before the ﬁve seconds has elapsed, the doors will not lock until ﬁve seconds after all doors are closed. If the power door lock switch or the transmitter lock button is pressed twice when leaving the vehicle, the doors will lock immediately. If the power door unlock switch or the transmitter unlock button is pressed, the doors will unlock immediately and not lock automatically after the doors are closed. This feature is turned on at the factory but may be turned off through the Driver Information Center (DIC). Automatic Door Lock Your vehicle is programmed at the factory to lock all doors automatically when the following are met: (cid:127) All doors are closed. The ignition is on. The shift lever is moved out of PARK (P) for vehicles with an automatic transaxle. The vehicle speed is greater than 5 mph (8 km/h) for vehicles with a manual transaxle. This feature cannot be disabled. If someone needs to exit the vehicle once the doors are locked, have that person use the manual lock knob or power door unlock switch. 2-12 (cid:127) (cid:127) (cid:127) (cid:127) (cid:127) Programmable Automatic Door Unlock If you have a vehicle with a manual transaxle, the doors will automatically unlock when the ignition is turned off. The automatic unlock feature cannot be programmed. If you have a vehicle with an automatic transaxle, it was programmed at the factory to unlock when the shift lever is moved to PARK (P). You can change when the automatic unlocking occurs through the Driver Information Center (DIC). See DIC Vehicle Personalization on page 3-52. Lockout Protection This feature prevents the driver’s door from being locked using the power door locks, if the key is left in the ignition and a door is open. Pressing the power door lock switch will lock all the doors and then unlock the driver’s door. Pressing and holding the power door lock switch for more than three seconds will override this feature. If you remove the key from the ignition, or if you use the manual door lock or the remote keyless entry transmitter, you could still lock your key inside your vehicle. Always remember to take your key with you. 2-13 Trunk To open the trunk from the outside, use the key or press the trunk release button on the remote keyless entry transmitter. When closing the trunk, close from the center of the lid to ensure it fully latches. {CAUTION: It can be dangerous to drive with the trunk lid open because carbon monoxide (CO) gas can come into your vehicle. You cannot see or smell CO. It can cause unconsciousness and even death. If you must drive with the trunk lid open or if electrical wiring or other cable connections must pass through the seal between the body and the trunk lid: (cid:127) Make sure all other windows are shut. (cid:127) Turn the fan on your heating or cooling system to its highest speed and select the control setting that will force outside air into your vehicle. See Climate Control System. If you have air outlets on or under the instrument panel, open them all the way. See Engine Exhaust on page 2-37. 2-14 (cid:127) Remote Trunk Release Emergency Trunk Release Handle From the inside, press this button located on the driver’s door near the map pocket to open the trunk. You can open the trunk only while the vehicle is stationary. Notice: Do not use the emergency trunk release handle as a tie-down or anchor point when securing items in the trunk as it could damage the handle. The emergency trunk release handle is only intended to aid a person trapped in a latched trunk, to open the trunk from the inside. There is a glow-in-the-dark emergency trunk release handle located inside the trunk on the trunk latch. This handle will glow following exposure to light. Pull the release handle up to open the trunk from the inside. 2-15 Windows {CAUTION: Leaving children, helpless adults, or pets in a vehicle with the windows closed is dangerous. They can be overcome by the extreme heat and suffer permanent injuries or even death from heat stroke. Never leave a child, a helpless adult, or a pet alone in a vehicle, especially with the windows closed in warm or hot weather. 2-16 Power Windows Sedan Switches shown; Retractable Hardtop similar Coupe Switches The power window switches for all the windows are located on the driver’s door armrest. Each passenger door also has a power window switch for its own window. Press the front of the switch to the ﬁrst position to lower the window to the desired level. Pull the switch up to raise the window. 2-17 Window Indexing (Coupe and Retractable Hardtop) This feature automatically lowers the window a small amount when the door is opened. Then, when the door is closed, the window will automatically raise fully. Power Window Initialize (Coupe and Retractable Hardtop) After a power reconnect, such as battery replacement, the indexing feature will not function until the system is initialized. This procedure needs to be done for each individual window. Once power is restored, do the following: 1. Close the door. 2. Raise the window by pulling the power window switch up. 3. Hold the window switch up for two seconds after the window is closed. Release the switch. Then hold the switch up again for two seconds. 4. Lower the window all the way down. Hold the switch down for two seconds. 5. Repeat the procedure for each window, including the rear quarter windows on convertible models, until all windows are initialized. Express-Down Window The express-down feature lowers the window all the way without continuously pressing the switch. The switch(es) is labeled AUTO. On sedan and retractable hardtop models, the driver’s window has the express-down feature. On coupe models, both the driver’s and front passenger’s window have the express-down feature. The front passenger’s express-down is activated by the driver’s side switch only. Press the front of the switch all the way down and release it to express open the window. To stop the window while it is lowering, pull the front of the switch up brieﬂy. Window Lockout (Sedan Only) o (Window Lockout): This button prevents the rear passengers from using their window switches. The window lockout button is located near the driver’s power window switches. The driver can still operate all the windows and the front passenger can operate their own window with the lockout on. Press the right side of the switch to turn the lockout feature on. Press the left side to turn it off. The red part of the switch is visible when you have returned to normal window operation. 2-18 Sun Visors Swing down the visors to block glare. The visors can be removed from the center mount and swung to the side. The visors also have extenders that can be pulled out for additional blockage. Your vehicle may have lighted vanity mirrors on the driver’s and passenger’s visors. When you lift the cover, the light will turn on. Theft-Deterrent Systems Vehicle theft is big business, especially in some cities. Although your vehicle has a number of theft-deterrent features, we know that nothing we put on it can make it impossible to steal. Content Theft-Deterrent Your vehicle may have a content theft-deterrent alarm system. Arming the System With the ignition off, you can arm the system by pressing the remote keyless entry transmitter lock button or the power door lock switch while the driver’s door is open. The system will arm thirty seconds after all the doors are closed, or sixty seconds with any door open. If you press the lock button on the transmitter a second time while all the doors are closed, the system will arm immediately. The system will still arm in sixty seconds if a door is open. When the open door is closed, it will also become armed. The security light, located on the instrument panel cluster, will turn on to indicate that arming has been initiated. Once the system is armed, the security light will ﬂash once every three seconds. If the security light is ﬂashing twice per second, this means that a door is open. If you do not want to arm the system, you may lock the car with the lock levers on the doors. Disarming the System You can disarm the system by pressing the remote keyless entry transmitter unlock button, or turning the ignition on. Once the system is disarmed, the security light will stop ﬂashing. 2-19 How the System Alarm is Activated If the system is armed, it can be activated by: (cid:127) Opening the driver’s door or trunk. This will cause a ten second pre-alarm chirp followed by a thirty second full alarm of horn and lights. (cid:127) Opening any other door. This will immediately cause a full alarm of horn and lights for thirty seconds. (cid:127) Opening the hood. If the vehicle is equipped with the remote start feature, it will activate the full alarm. When an alarm event has ﬁnished, the system will re-arm itself automatically. How to Turn Off the System Alarm To turn off the system alarm, do one of the following: (cid:127) Press the lock button on the remote keyless entry transmitter. The system will then re-arm itself. (cid:127) Press the unlock button on the remote keyless entry transmitter. This will also disarm the system. Insert the key in the ignition and turn it on. This will also disarm the system. 2-20 How to Detect a Tamper Condition If you hear three chirps when you press the unlock or lock buttons on the remote keyless transmitter, it means that the content theft security system alarm was triggered previously. PASS-Key® III+ Your PASS-Key® III+ system operates on a radio frequency subject to Federal Communications Commission (FCC) Rules and with Industry Canada. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation. This device complies with RSS-210 of Industry Canada. Operation is subject to the following two conditions: 1. This device may not cause interference. 2. This device must accept any interference received, including interference that may cause undesired operation of the device. Changes or modiﬁcations to this system by other than an authorized service facility could void authorization to use this equipment. PASS-Key® III+ uses a radio frequency transponder in the key that matches a decoder in your vehicle. (cid:127) PASS-Key® III+ Operation Your vehicle is equipped with PASS-Key® III+ (Personalized Automotive Security System) theft-deterrent system. PASS-Key® III+ is a passive theft-deterrent system. This means you don’t have to do anything special to arm or disarm the system. It works when you insert or remove the key from the ignition. When the PASS-Key® III+ system senses that someone is using the wrong key, it prevents the vehicle from starting. Anyone using a trial-and-error method to start the vehicle will be discouraged because of the high number of electrical key codes. When trying to start the vehicle if the engine does not start and the SECURITY light comes on, the key may have a damaged transponder. Turn the ignition off and try again. If the engine still does not start, and the key appears to be undamaged, try another ignition key. At this time, you may also want to check the fuse, see Fuses on page 5-97. If the engine still does not start with the other key, your vehicle needs service. If your vehicle does start, the ﬁrst key may be faulty. See your dealer who can service the PASS-Key® III+ to have a new key made. In an emergency, contact Roadside Assistance. It is possible for the PASS-Key® III+ decoder to “learn” the transponder value of a new or replacement key. Up to 10 additional keys may be programmed for the vehicle. The following procedure is for programming additional keys only. If all the currently programmed keys are lost or do not operate, you must see your dealer or a locksmith who can service PASS-Key® III+ to have keys made and programmed to the system. See your dealer or a locksmith who can service PASS-Key® III+ to get a new key blank that is cut exactly as the ignition key that operates the system. To program the new key do the following: 1. Verify that the new key has “+” stamped on it. 2. Insert the already programmed key in the ignition and start the engine. If the engine will not start, see your dealer for service. 3. After the engine has started, turn the key to OFF, and remove the key. 4. Insert the key to be programmed and turn it to the ON position within ﬁve seconds of removing the original key. 5. The SECURITY light will turn off once the key has been programmed. 6. Repeat Steps 1 through 5 if additional keys are to be programmed. 2-21 If you are ever driving and the SECURITY light comes on and stays on, you may be able to restart your engine if you turn it off. Your PASS-Key® III+ system, however, is not working properly and must be serviced by your dealer. Your vehicle is not protected by the PASS-Key® III+ system at this time. If you lose or damage your PASS-Key® III+ key, see your dealer or a locksmith who can service PASS-Key® III+ to have a new key made. Starting and Operating Your Vehicle New Vehicle Break-In Notice: Your vehicle does not need an elaborate break-in. But it will perform better in the long run if you follow these guidelines: (cid:127) Do not drive at any one speed, fast or slow, for the ﬁrst 500 miles (805 km). Do not make full-throttle starts. (cid:127) Avoid making hard stops for the ﬁrst 200 miles (322 km) or so. During this time your new brake linings are not yet broken in. Hard stops with new linings can mean premature wear and earlier replacement. Follow this breaking-in guideline every time you get new brake linings. (cid:127) Do not tow a trailer during break-in. See Towing a Trailer on page 4-40 for more information. 2-22 Ignition Positions With the key in the ignition switch, you can turn it to four different positions. Notice: Using a tool to force the key from the ignition switch could cause damage or break the key. Use the correct key and turn the key only with your hand. Make sure the key is in all the way. If none of this works, then your vehicle needs service. 9 (OFF): This is the only position from which you can remove the key. For a vehicle with an automatic transaxle, the shift lever must be in PARK (P) with the ignition in OFF to remove the key. For a vehicle with a manual transaxle, the shift lever must be in REVERSE (R) to remove the key. A warning chime will sound if you open the driver’s door while the ignition is off and the key is in the ignition. ACC (ACCESSORY): This position unlocks the transaxle. It also lets you use things like the radio and windshield wipers while the engine is not running. To use ACC, turn the key clockwise to the ﬁrst position. Use this position if your vehicle must be pushed or towed. See Recreational Vehicle Towing on page 4-38. Never try to push-start your vehicle, unless it has a manual transaxle. R (ON): This position is where the key returns to after you start the engine and release the key. The ignition switch will stay in this position while the engine is running. But even while the engine is not running, you can use ON to operate your electrical accessories and to display some instrument panel warning lights. Use the ON position for push-starting a vehicle with a manual transaxle. / (START): This position starts the engine. When the engine starts, release the key. The ignition switch will return to the ON position for normal driving. 2-23 Retained Accessory Power (RAP) Your vehicle is equipped with a Retained Accessory Power (RAP) feature which will allow the radio, retractable hardtop, if equipped, and power windows to continue to work up to 10 minutes after the ignition is turned OFF, or when the driver’s door is opened. If the front passenger door is opened the windows and sunroof function is discontinued. Your radio and power windows will work when the ignition key is ON or ACC. Once the key is turned from ON to OFF, the radio will continue to work for up to 10 minutes or until the driver’s door is opened. Also, while in the RAP mode power window and retractable hardtop, if equipped, operation is allowed for up to 10 minutes or until any door is opened. Starting the Engine Automatic Transaxle Move your shift lever to PARK (P) or NEUTRAL (N). Your engine will not start in any other position — that is a safety feature. To restart when you are already moving, use NEUTRAL (N) only. Notice: Shifting into PARK (P) with the vehicle moving could damage the transaxle. Shift into PARK (P) only when your vehicle is stopped. 2-24 Manual Transaxle The shift lever should be in the neutral and the parking brake engaged. Hold the clutch pedal to the ﬂoor and start the engine. Your vehicle will not start if the clutch pedal is not all the way down. That is a safety feature. Starting Your 2.4L L4 ECOTEC® Engine 1. With your foot off the accelerator pedal, turn your ignition key to START. When the engine starts, let go of the key. The idle speed will go down as your engine gets warm. Notice: Holding your key in START for longer than 15 seconds at a time will cause your battery to be drained much sooner. And the excessive heat can damage your starter motor. Wait about 15 seconds between each try to help avoid draining your battery or damaging your starter. 2. If it does not start, wait about 15 seconds and try again to start the engine by turning the ignition key to START. Wait about 15 seconds between each try. When your engine has run about 10 seconds to warm up, your vehicle is ready to be driven. Do not “race” your engine when it is cold. If the weather is below freezing (32°F or 0°C), let the engine run for a few minutes to warm up. 3. If your engine still will not start, or starts but then stops, it could be ﬂooded with too much gasoline. Try pushing your accelerator pedal all the way to the ﬂoor and holding it there as you hold the key in START for about three seconds. If the vehicle starts brieﬂy but then stops again, do the same thing, but this time keep the pedal down for ﬁve or six seconds. This clears the extra gasoline from the engine. Notice: Your engine is designed to work with the electronics in your vehicle. If you add electrical parts or accessories, you could change the way the engine operates. Before adding electrical equipment, check with your dealer. If you do not, your engine might not perform properly. Any resulting damage would not be covered by your vehicle’s warranty. Starting Your 3.5L V6 Engine 1. With your foot off the accelerator pedal, turn your ignition key to START. When the engine starts, let go of the key. The idle speed will go down as your engine warms up. Notice: Holding your key in START for longer than 15 seconds at a time will cause your battery to be drained much sooner. And the excessive heat can damage your starter motor. Wait about 15 seconds between each try to help avoid draining your battery or damaging your starter. 2. If the engine does not start in 10 seconds, push the accelerator pedal about one-quarter of the way down while you turn the key to START. Do this until the engine starts. As soon as it does, let go of the key. 3. If your engine still will not start, or starts but then stops, it could be ﬂooded with too much gasoline. Try pushing your accelerator pedal all the way to the ﬂoor and holding it there as you hold the key in START for a maximum of 15 seconds. This clears the extra gasoline from the engine. If the engine still will not start or starts brieﬂy but then stops again, repeat Step 1 or 2, depending on temperature. When the engine starts, release the key and the accelerator pedal. Notice: Your engine is designed to work with the electronics in your vehicle. If you add electrical parts or accessories, you could change the way the engine operates. Before adding electrical equipment, check with your dealer. If you do not, your engine might not perform properly. Any resulting damage would not be covered by your vehicle’s warranty. 2-25 Starting Your 3.9L V6 Engine 1. With your foot off the accelerator pedal, turn your ignition key to START. When the engine starts, let go of the key. The idle speed will go down as your engine warms up. Notice: Holding your key in START for longer than 15 seconds at a time will cause your battery to be drained much sooner. And the excessive heat can damage your starter motor. Wait about 15 seconds between each try to help avoid draining your battery or damaging your starter. 2. If the engine does not start in 10 seconds, push the accelerator pedal about one-quarter of the way down while you turn the key to START. Do this until the engine starts. As soon as it does, let go of the key. 3. If your engine still will not start, or starts but then stops, it could be ﬂooded with too much gasoline. Try pushing your accelerator pedal all the way to the ﬂoor and holding it there as you hold the key in START for a maximum of 15 seconds. This clears the extra gasoline from the engine. If the engine still will not start or starts brieﬂy but then stops again, repeat Step 1 or 2, depending on temperature. When the engine starts, release the key and the accelerator pedal. 2-26 Notice: Your engine is designed to work with the electronics in your vehicle. If you add electrical parts or accessories, you could change the way the engine operates. Before adding electrical equipment, check with your dealer. If you do not, your engine might not perform properly. Any resulting damage would not be covered by your vehicle’s warranty. Adjustable Throttle and Brake Pedal (Automatic Transaxle) If your vehicle has this feature, you can change the position of the throttle and brake pedals. This feature is designed for shorter drivers, since the pedals cannot move farther away from the standard position, but can move rearward for better pedal reach. The vehicle must be in PARK (P) or have the ignition off for this feature to operate. If the system senses unusually high resistance while the pedals are being adjusted, such as a driver’s foot pushing the brake pedal, it is designed to disable the switch. Simply remove the obstruction and try to adjust the pedals again. The switch used to adjust the pedals is located on the left side of the instrument panel. To use your adjustable throttle and brake pedal feature, do the following: The adjustable pedal feature is meant to be used with the adjustable seat and adjustable steering wheel controls to reach a safe and comfortable position. 1. Adjust your seat to a comfortable position where you can comfortably reach other controls such as the radio and climate controls. 2. Adjust the throttle and brake pedals to reach a comfortable and safe operating position. 3. Adjust the steering wheel to a safe operating position. Engine Coolant Heater Your vehicle may have this feature. In very cold weather, 0°F (−18°C) or colder, the engine coolant heater can provide easier starting and better fuel economy during engine warm-up. Usually, the coolant heater should be plugged in a minimum of four hours prior to starting your vehicle. At temperatures above 32°F (0°C), use of the coolant heater is not required. Your vehicle may also have an internal thermostat in the plug end of the cord. This will prevent operation of the engine coolant heater when the temperature is at or above 0°F (−18°C) as noted on the cord. To Use the Engine Coolant Heater 1. Turn off the engine. 2. Open the hood and unwrap the electrical cord. On the 2.4L L4 ECOTEC® engine, the engine coolant heater cord is located near the air cleaner box on the passenger’s side of the engine compartment. On the 3.5L and 3.9L V6 engines, the engine coolant heater cord is located on the driver’s side around the battery box. See Engine Compartment Overview on page 5-12 for more information on location. 2-27 3. Plug the cord into a normal, grounded 110-volt AC outlet. Automatic Transaxle Operation {CAUTION: Plugging the cord into an ungrounded outlet could cause an electrical shock. Also, the wrong kind of extension cord could overheat and cause a ﬁre. You could be seriously injured. Plug the cord into a properly grounded three-prong 110-volt AC outlet. If the cord will not reach, use a heavy-duty three-prong extension cord rated for at least 15 amps. 4. Before starting the engine, be sure to unplug and store the cord as it was before to keep it away from moving engine parts. If you do not, it could be damaged. How long should you keep the coolant heater plugged in? The answer depends on the outside temperature, the kind of oil you have, and some other things. Instead of trying to list everything here, we ask that you contact your dealer in the area where you will be parking your vehicle. The dealer can give you the best advice for that particular area. 2-28 SE Model GT and GTP Models Your automatic transaxle has a shift lever located on the console between the seats. PARK (P): This position locks your front wheels. It is the best position to use when you start your engine because your vehicle cannot move easily. {CAUTION: It is dangerous to get out of your vehicle if the shift lever is not fully in PARK (P) with the parking brake ﬁrmly set. Your vehicle can roll. Do not leave your vehicle when the engine is running unless you have to. If you have left the engine running, the vehicle can move suddenly. You or others could be injured. To be sure your vehicle will not move, even when you are on fairly level ground, always set your parking brake and move the shift lever to PARK (P). See Shifting Into Park (P) (Automatic Transaxle) on page 2-34. If you are pulling a trailer, see Towing a Trailer on page 4-40. Ensure the shift lever is fully in PARK (P) before starting the engine. Your vehicle has an automatic transaxle shift lock control system. You have to apply your regular brake and press the shift lever button before you can shift from PARK (P) while the ignition key is in ON. If you cannot shift out of PARK (P), ease pressure on the shift lever and push the shift lever all the way into PARK (P) as you maintain brake application. Then move the shift lever into another gear. See Shifting Out of Park (P) (Automatic Transaxle) on page 2-36 later in this section. REVERSE (R): Use this gear to back up. Notice: Shifting to REVERSE (R) while your vehicle is moving forward could damage the transaxle. The repairs would not be covered by your warranty. Shift to REVERSE (R) only after your vehicle is stopped. To rock your vehicle back and forth to get out of snow, ice or sand without damaging your transaxle, see If Your Vehicle is Stuck in Sand, Mud, Ice or Snow on page 4-32. 2-29 NEUTRAL (N): In this position, your engine does not connect with the wheels. To restart when you are already moving, use NEUTRAL (N) only. Also, use NEUTRAL (N) when your vehicle is being towed. {CAUTION: Shifting into a drive gear while your engine is running at high speed is dangerous. Unless your foot is ﬁrmly on the brake pedal, your vehicle could move very rapidly. You could lose control and hit people or objects. Do not shift into a drive gear while your engine is running at high speed. Notice: Shifting out of PARK (P) or NEUTRAL (N) while the engine is running at high speed may damage the transaxle. The repairs would not be covered by your warranty. Be sure the engine is not running at high speeds when shifting your vehicle. 2-30 AUTOMATIC OVERDRIVE (D): This position is for normal driving. If you need more power for passing, and you are: (cid:127) Going less than 35 mph (55 km/h), push your accelerator pedal about halfway down. (cid:127) Going about 35 mph (55 km/h) or more, push the accelerator all the way down. If your vehicle seems to start up rather You will shift down to the next gear and have more power. Notice: slowly or not shift gears when you go faster, and you continue to drive your vehicle that way, you could damage the transaxle. Have your vehicle serviced right away. You can drive in LOW (L) when you are driving less than 35 mph (55 km/h) and AUTOMATIC OVERDRIVE (D) for higher speeds until then. THIRD (3): This position, available on the SE model, is also used for normal driving. However, it offers more power and lower fuel economy than AUTOMATIC OVERDRIVE (D). Here are some times you might choose THIRD (3) instead of AUTOMATIC OVERDRIVE (D): (cid:127) When driving on hilly, winding roads. (cid:127) When towing a trailer, so there is less shifting between gears. (cid:127) When going down a steep hill. LOW (L): This position, available on the SE model, gives you more power but lower fuel economy than THIRD (3). You can use LOW (L) on hills. It can help control your speed as you go down steep mountain roads, but then you would also want to use your brakes off and on. You can use LOW (L) on very steep hills, or in deep snow or mud. If the shift lever is put in LOW (L), the transaxle will not shift into ﬁrst gear until the vehicle is going slowly enough. Notice: Driving in LOW (L) for more than 25 miles (40 km) or at speeds over 55 mph (90 km/h) may damage the transaxle. Also, shifting into LOW (L) at speeds above 65 mph (105 km/h) can cause damage. Drive in THIRD (3) or AUTOMATIC OVERDRIVE (D) instead of LOW (L). Notice: Spinning the tires or holding the vehicle in one place on a hill using only the accelerator pedal may damage the transaxle. If you are stuck, do not spin the tires. When stopping on a hill, use the brakes, or parking brake to hold the vehicle in place. MANUAL MODE (M): This position, available on the GT/GTP models, allows you to change gears similar to a manual transaxle. If your vehicle has this feature, see Manual Shift Mode (MSM). Manual Shift Mode (MSM) (Automatic Transaxle) To use this feature, do the following: 1. Move the shift lever from AUTOMATIC OVERDRIVE (D) rearward and then to the right into the MANUAL MODE (M). 2. If you do not move the shift lever forward or rearward, the vehicle will be in the manual mode and a gear based on the current driving speed. While driving in manual mode, the transaxle may remain in a gear longer than it would in normal driving mode based on braking, throttle input and vehicle lateral acceleration. 3. Press the shift level forward to upshift or rearward to downshift. The odometer on the instrument panel cluster will change from the vehicle’s mileage to the letter M, for manual mode, and a number indicating the requested gear range when moving the shift lever forward or rearward. See Speedometer and Odometer on page 3-31 for more information. 2-31 SECOND (2) Gear Start Feature When accelerating your vehicle from a stop in snowy and icy conditions, you may want to shift into SECOND (2) gear. A higher gear allows you to gain more traction on slippery surfaces. With the MSM feature, the vehicle can be set to pull away in SECOND (2) gear. 1. Move the shift lever from AUTOMATIC OVERDRIVE (D) into the MANUAL MODE (M). 2. With the vehicle stopped, move the lever forward to select SECOND (2) gear. The vehicle will start from a stop position in SECOND (2) gear. 3. Once moving select the desired drive gear. While using the MSM feature the vehicle will have ﬁrmer shifting and increased performance. You can use this for sport driving or when climbing hills to stay in gear longer or to downshift for more power or engine braking. The transaxle will only allow you to shift into gears appropriate for the vehicle speed and engine revolutions per minute (RPM). The transaxle will not automatically shift to the next higher gear if the engine RPM is too high. When coming to a stop in the manual mode, the vehicle will automatically downshift to the proper gear based on speed. Upon acceleration you will need to manually upshift to the desired gear. 2-32 Manual Transaxle Operation This is your shift pattern. The clutch must be fully pressed in when shifting a manual transaxle to ensure the transaxle is fully in gear. Here is how to operate your transaxle: FIRST (1): Press the clutch pedal and shift into FIRST (1). Then, slowly let up on the clutch pedal as you press the accelerator pedal. You can shift into FIRST (1) when you are going less that 20 mph (32 km/h). If you have come to a complete stop and it is hard to shift into FIRST (1), put the shift lever into Neutral and let up on the clutch. Press the clutch pedal back down. Then shift into FIRST (1). SECOND (2): Press the clutch pedal as you let up on the accelerator pedal and shift into SECOND (2). Then, slowly let up on the clutch pedal as you press the accelerator pedal. THIRD (3), FOURTH (4), and FIFTH (5) and SIXTH (6): Shift into THIRD (3), FOURTH (4) and FIFTH (5) and SIXTH (6) the same way you do for SECOND (2). Slowly let up on the clutch pedal as you press the accelerator pedal. To stop, let up on the accelerator pedal and press the brake pedal. Just before the vehicle stops, press the clutch pedal and the brake pedal, and shift to Neutral. Neutral: Use this position when you start or idle your engine. REVERSE (R): To back up, press down the clutch pedal and lift up on the ring on the shift lever to shift into REVERSE (R). Let up on the clutch pedal slowly while pressing the accelerator pedal. Notice: Shifting to REVERSE (R) while your vehicle is moving forward could damage the transaxle. The repairs would not be covered by your warranty. Shift to REVERSE (R) only after your vehicle is stopped. Also, use REVERSE (R), along with the parking brake, for parking your vehicle. Once the shift lever is in REVERSE (R), the ignition can be turned to OFF and the key removed. Parking Brake GT and GTP Shown, SE Similar To set the parking brake, pull up on the parking brake handle. If the ignition is on, the brake system warning light will come on. See Brake System Warning Light on page 3-36. 2-33 To release the parking brake, hold the brake pedal down. Pull the parking brake handle up until you can press the release button. Hold the release button in as you move the brake handle all the way down. Notice: Driving with the parking brake on can overheat the brake system and cause premature wear or damage to brake system parts. Verify that the parking brake is fully released and the brake warning light is off before driving. If you are towing a trailer and you are parking on a hill, see Towing a Trailer on page 4-40. Shifting Into Park (P) (Automatic Transaxle) {CAUTION: It can be dangerous to get out of your vehicle if the shift lever is not fully in PARK (P) with the parking brake ﬁrmly set. Your vehicle can roll. If you have left the engine running, the vehicle can move suddenly. You or others could be injured. To be sure your vehicle will not move, even when you are on fairly level ground, use the steps that follow. If you are pulling a trailer, see Towing a Trailer on page 4-40. 2-34 Use the following procedure to shift into PARK (P): 1. Hold the brake pedal down with your right foot and set the parking brake. 2. Move the shift lever into PARK (P) by holding in the button on the shift lever and pushing the lever all the way toward the front of the vehicle. 3. Turn the ignition key to OFF. 4. Remove the key and take it with you. If you can leave your vehicle with the ignition key in your hand, your vehicle is in PARK (P). Leaving Your Vehicle With the Engine Running (Automatic Transaxle) {CAUTION: It can be dangerous to leave your vehicle with the engine running. Your vehicle could move suddenly if the shift lever is not fully in PARK (P) with the parking brake ﬁrmly set. And, if you leave the vehicle with the engine running, it could overheat and even catch ﬁre. You or others could be injured. Do not leave your vehicle with the engine running. If you have to leave your automatic transaxle vehicle with the engine running, be sure your vehicle is in PARK (P) and your parking brake is ﬁrmly set before you leave it. After you have moved the shift lever into PARK (P), hold the regular brake pedal down. Then, see if you can move the shift lever away from PARK (P) without ﬁrst pushing the button. If you can, it means that the shift lever was not fully locked into PARK (P). 2-35 Torque Lock (Automatic Transaxle) If you are parking on a hill and you do not shift your automatic transaxle into PARK (P) properly, the weight of the vehicle may put too much force on the parking pawl in the transaxle. You may ﬁnd it difficult to pull the shift lever out of PARK (P). This is called “torque lock.” To prevent torque lock, set the parking brake and then shift into PARK (P) properly before you leave the driver’s seat. To ﬁnd out how, see “Shifting Into Park (P)” previously in the section. When you are ready to drive, move the shift lever out of PARK (P) before you release the parking brake. If torque lock does occur, you may need to have another vehicle push yours a little uphill to take some of the pressure from the parking pawl in the transaxle, so you can pull the shift lever out of PARK (P). Shifting Out of Park (P) (Automatic Transaxle) The automatic transaxle shift lock control system locks the shift lever in PARK when the ignition is in OFF. In addition, you have to fully apply your regular brakes before you can shift from PARK (P) when the ignition is in ON. See Automatic Transaxle Operation on page 2-28. If you cannot shift out of PARK (P), ease pressure on the shift lever and push the shift lever all the way into PARK (P) as you maintain brake application. Then move the shift lever into the desired gear. Parking Your Vehicle (Manual Transaxle) Before leaving your vehicle, fully press the clutch pedal in, ﬁrmly apply the parking brake, and move the shift lever into REVERSE (R). Once the shift lever has been placed in REVERSE (R) with the clutch pedal pressed in, you can turn the ignition key to OFF, remove the key and release the clutch. See Manual Transaxle Operation on page 2-32. 2-36 Parking Over Things That Burn Engine Exhaust {CAUTION: Engine exhaust can kill. It contains the gas carbon monoxide (CO), which you cannot see or smell. It can cause unconsciousness and death. You might have exhaust coming in if: (cid:127) Your exhaust system sounds strange or different. (cid:127) Your vehicle gets rusty underneath. (cid:127) Your vehicle was damaged in a collision. (cid:127) Your vehicle was damaged when driving over high points on the road or over road debris. (cid:127) Repairs were not done correctly. (cid:127) Your vehicle or exhaust system had been modiﬁed improperly. If you ever suspect exhaust is coming into your vehicle: (cid:127) Drive it only with all the windows down to blow out any CO; and (cid:127) Have your vehicle ﬁxed immediately. 2-37 {CAUTION: Things that can burn could touch hot exhaust parts under your vehicle and ignite. Do not park over papers, leaves, dry grass or other things that can burn. Running the Engine While Parked It is better not to park with the engine running. But if you ever have to, here are some things to know. {CAUTION: {CAUTION: Idling the engine with the climate control system off could allow dangerous exhaust into your vehicle. See the earlier caution under Engine Exhaust on page 2-37. Also, idling in a closed-in place can let deadly carbon monoxide (CO) into your vehicle even if the climate control fan is at the highest setting. One place this can happen is a garage. Exhaust — with CO — can come in easily. NEVER park in a garage with the engine running. Another closed-in place can be a blizzard. See Winter Driving on page 4-27. It can be dangerous to get out of your vehicle if the automatic transaxle shift lever is not fully in PARK (P) with the parking brake ﬁrmly set. Your vehicle can roll. Do not leave your vehicle when the engine is running unless you have to. If you have left the engine running, the vehicle can move suddenly. You or others could be injured. To be sure your vehicle will not move, even when it is on fairly level ground, always set the parking brake and move the automatic transaxle shift lever to PARK (P), or the manual transaxle shift lever to NEUTRAL. Follow the proper steps to be sure your vehicle will not move. If you have an automatic transaxle, see Shifting Into Park (P) (Automatic Transaxle) on page 2-34. If you are parking on a hill and if you are pulling a trailer, see Towing a Trailer on page 4-40. 2-38 Mirrors Manual Rearview Mirror The mirror can be adjusted two ways. First, to adjust the height of the mirror, adjust the arm that connects the mirror to the windshield. Second, adjust the angle of the mirror, by moving the mirror to a position that allows you to see out of the back window. To reduce glare from headlamps behind you, move the lever toward you to the night position. To return the mirror to the daytime position, move the lever away from you. Manual Rearview Mirror with OnStar® Your vehicle may have a rearview mirror with the OnStar® system. Control buttons for the OnStar® system are at the bottom of the mirror. See your GM dealer for more information on the OnStar® system and how to subscribe to OnStar®. Also, see OnStar® System on page 2-44 for more information about the services OnStar® provides. Mirror Operation While sitting in a comfortable driving position, adjust the rearview mirror so you can see clearly behind your vehicle. Grip it in the center to move it up or down and side to side. The day/night control, located at the bottom of the mirror, adjusts the mirror to reduce headlamp glare from behind during evening or dark conditions. Move the control to the right for night conditions. Return it to the center for daytime use. Automatic Dimming Rearview Mirror with OnStar® and Compass Your vehicle may have an automatic dimming rearview mirror with a compass and OnStar® controls. For more information about OnStar®, see OnStar® System on page 2-44. The automatic dimming feature turns on each time the vehicle is started. To turn automatic dimming off or on, press the left button below the mirror. A green indicator light will be on when automatic dimming is on. There are also three OnStar® buttons located at the bottom of the mirror. See your dealer for more information on the system and how to subscribe to OnStar®. See OnStar® System on page 2-44 for more information about the service OnStar® provides. 2-39 Compass Operation Press the on/off button once to turn the compass on or off. When the ignition and the compass feature are on, the compass will show two character boxes for a few seconds. After a few seconds, the mirror will display the current compass direction. Compass Calibration If after a few seconds the display does not show a compass direction, (N for North for example), there may be a strong magnetic ﬁeld interfering with the compass. Such interference may be caused by a magnetic antenna mount, note pad holder, or similar object. If the letter C appears in the compass window, the compass may need to be reset or calibrated. The mirror can be calibrated by driving the vehicle in circles at 5 mph (8 km/h) or less until the display reads a direction. Compass Variance Compass variance is the difference between earth’s magnetic north and true geographic north. If the mirror is not adjusted for compass variance, the compass could give false readings. The mirror is set in zone eight upon leaving the factory. It will be necessary to adjust the compass to compensate for compass variance if the vehicle is driven outside zone eight. Under certain circumstances, such as a long distance, cross-country trip, it will be necessary to adjust the compass variance. To adjust for compass variance, do the following: 1. Find your current location and variance zone number on the zone map that follows. 2-40 Automatic Dimming Rearview Mirror with Compass Your vehicle may have an automatic dimming rearview mirror with a compass. This feature enables the mirror to sense nighttime glare from vehicle headlamps from behind and automatically dim to reduce the glare to a safe level. The automatic dimming feature turns on each time the vehicle is started. Press the OFF button once and the green indicator light located to the left of the button will go out indicating the feature is off. To turn the feature back on, press and release the AUTO button and the green indicator light will come on. Compass Operation Press the on/off button once to turn the compass on or off. When the ignition and the compass feature are on, the compass will show two character boxes for a few seconds. After a few seconds, the mirror will display the current compass direction. 2-41 2. Press and hold the on/off button until a zone number appears on the display. 3. Once the zone number appears on the display, press the on/off button quickly until you reach the correct zone number. If C appears in the compass window, the compass may need calibration. See “Compass Calibration” listed previously. Compass Calibration If after a few seconds the display does not show a compass direction, (N for North for example), there may be a strong magnetic ﬁeld interfering with the compass. Such interference may be caused by a magnetic antenna mount, note pad holder, or similar object. If the letter C appears in the compass window, the compass may need to be reset or calibrated. The mirror can be calibrated by driving the vehicle in circles at 5 mph (8 km/h) or less until the display reads a direction. Compass Variance Compass variance is the difference between earth’s magnetic north and true geographic north. If the mirror is not adjusted for compass variance, the compass could give false readings. The mirror is set in zone eight upon leaving the factory. It will be necessary to adjust the compass to compensate for compass variance if the vehicle is driven outside zone eight. Under certain circumstances, such as a long distance, cross-country trip, it will be necessary to adjust the compass variance. To adjust for compass variance, do the following: 1. Find your current location and variance zone number on the zone map that follows. 2-42 2. Press and hold the on/off button until a zone number appears on the display. 3. Once the zone number appears on the display, press the on/off button quickly until you reach the correct zone number. If C appears in the compass window, the compass may need calibration. See “Compass Calibration” listed previously. Outside Power Mirrors Outside Convex Mirror The controls for the outside power mirrors, are located on the driver’s door. Move the selector switch located next to the control pad to the left or right to choose either the driver’s side or passenger’s side mirror. To adjust a mirror, use the arrows located on the control pad to move the mirror in the desired direction. Adjust each outside mirror so that a little of the vehicle and the area behind it can be seen while sitting in a comfortable driving position. Keep the selector switch in the center position when not adjusting either outside mirror. Both mirrors can manually be folded by pulling them toward the vehicle. This feature may be useful when going through a car wash or a conﬁned space. Push the mirrors away from the vehicle, to the normal position, before driving. {CAUTION: A convex mirror can make things (like other vehicles) look farther away than they really are. If you cut too sharply into the right lane, you could hit a vehicle on your right. Check your inside mirror or glance over your shoulder before changing lanes. The passenger’s side mirror is convex. A convex mirror’s surface is curved so more can be seen from the driver’s seat. It also makes things, like other vehicles, look farther away than they really are. 2-43 OnStar® System OnStar® uses global positioning system (GPS) satellite technology, wireless communications, and call centers to provide you with a wide range of safety, security, information, and convenience services. A complete OnStar® user’s guide and the terms and conditions of the OnStar® Subscription Service Agreement are included in the vehicle’s glove box literature. For more information, visit www.onstar.com or www.onstarcanada.com. Contact OnStar® at 1-888-4-ONSTAR (1-888-466-7827), or press the OnStar® button to speak to an OnStar® advisor 24 hours a day, 7 days a week. Terms and conditions of the Subscription Service Agreement can be found at www.onstar.com or www.onstarcanada.com. 2-44 OnStar® Services For new vehicles equipped with OnStar®, the Safe and Sound Plan is included for the ﬁrst year. You can extend this plan beyond the ﬁrst year, or upgrade to the Directions and Connections Plan to meet your needs. For more information, press the OnStar® button to speak with an advisor. Safe and Sound Plan (cid:127) Advanced Automatic Collision Notiﬁcation (cid:127) Automatic Notiﬁcation of Airbag Deployment (cid:127) Emergency Services (cid:127) Roadside Assistance (cid:127) Stolen Vehicle Tracking (cid:127) AccidentAssist (cid:127) Remote Door Unlock/Vehicle Alert (cid:127) Remote Diagnostics (cid:127) Online Concierge Directions and Connections Plan (cid:127) All Safe and Sound Plan Services (cid:127) Driving Directions (cid:127) RideAssist Information and Convenience Services (cid:127) OnStar® Personal Calling As an OnStar® subscriber, the Personal Calling capability is an available hands-free wireless phone that is integrated into the vehicle. Calls can be placed nationwide using simple voice commands with no additional contracts and no additional roaming charges. To ﬁnd out more about OnStar® Personal Calling, refer to the OnStar® user’s guide in the vehicle’s glove box or visit www.onstar.com or www.onstarcanada.com; or speak with an OnStar® advisor by pressing the OnStar® button or by calling 1-888-4-ONSTAR (1-888-466-7827). OnStar® Virtual Advisor Your vehicle may have Virtual Advisor. It is a feature of OnStar® Personal Calling that uses your minutes to access weather, local traffic reports, and stock quotes. By pressing the phone button and giving a few simple voice commands, you can browse through the various topics. Customize your information proﬁle at www.myonstar.com. See the OnStar® user’s guide for more information. Storage Areas Glove Box To open the glove box, lift up on the lever. Cupholder(s) There are two cupholders in the front center console of the vehicle and two in the rear of the center console. Pull down the door on the rear of the center console to use the rear seat cupholders. Center Console Storage Area The center console has a separate storage area. To open the compartment, which is also the armrest, pull up the latch release handle on the front of the lid. In the ﬂoor console is a power accessory outlet. See Accessory Power Outlet(s) on page 3-19 for more information. 2-45 Sunroof Convenience Net The vehicle may have a convenience net located on the back wall or the sides of the trunk. Put small loads, like grocery bags, behind the net. It can help keep them from falling over. The net is not for larger, heavier loads. Store those in the trunk as far forward as possible. Unhook the net so that it will lie ﬂat when not in use. If your vehicle has a sunroof, the switch is located on the headliner between the map lamps. The sunroof will only operate while the ignition is in ON or in ACC, or if Retained Accessory Power (RAP) is active. See Retained Accessory Power (RAP) on page 2-24. Press the back of the switch and release it to open the sunroof to the vent position. From the vent position, press and release the back of the switch to express-open the sunroof. To stop the sunroof from express opening, press the switch again. If the sunshade is closed, it will open automatically when the sunroof opens past the vented position. 2-46 If you force the sunshade forward of the To close the sunroof, press the front of the switch and hold it until the sunroof is closed. The sunroof will stop if the switch is released. Close the sunshade by hand. The sunroof glass panel cannot be opened or closed if the vehicle has an electrical failure. Notice: sliding glass panel, damage will occur and the sunroof may not open or close properly. Always close the glass panel before closing the sunshade. Sunroof - Panoramic If the vehicle has a panoramic sunroof, it has four glass panels that tilt or stack upon each other, when the sunroof control is turned to the vent or one of three opened positions. There is a separate control for the automatic sunshade. The sunroof will only operate while the ignition is ON or in ACC, or if Retained Accessory Power (RAP) is active. See Retained Accessory Power (RAP) on page 2-24. The panoramic sunroof control is located on the headliner. From the closed position, turn the control clockwise to vent the sunroof or open it to three different positions. 0 (Closed Position): Turn the control to this position to close the panoramic sunroof. 1 (Vent Position): Turn the control to this position to vent the panoramic sunroof. The front glass panel of the sunroof will tilt forward and the sunshade will automatically retract to the vent position. 2-47 2 (First-Open Position): Turn the control to this position to open the panoramic sunroof about a third of the way. The second glass panel will retract and the fourth glass panel will stack above the roof. The sunshade will automatically retract to this position. 3 (Second-Open Position): Turn the control to this position to open the panoramic sunroof about half-way. The second glass panel will retract and the third panel will stack in front of the fourth glass panel. The sunshade will automatically retract to this position. 4 (Full-Open Position): Turn the control to this position to completely open the panoramic sunroof. The second glass panel retracts and stacks in front of the third and fourth panels. The sunshade will automatically retract to the full-open position. To lessen wind noise in this position, use the automatic sunshade control and close the sunshade to the comfort stop position. See “Sunshade” following. Anti-Pinch Feature If an object is in the path of the sunroof when it is closing, the anti-pinch feature will detect the object and stop the sunroof from closing at the point of obstruction. The sunroof will then reverse direction. 2-48 Sunshade The automatic sunshade control is located on the headliner, between the map lamp controls. The sunshade can be independently opened or closed while the panoramic sunroof is closed. To express-open or express-close the sunshade, press and release the control rearward or forward. The sunshade will retract to the full-open or closed position. To stop the movement of the sunshade, press the control a second time. To close the sunshade to a particular position, continue to press the control and release it when the desired position is reached. Neither the panoramic sunroof or the sunshade can be opened or closed if the vehicle has an electrical failure. Retractable Hardtop The following procedures explain the proper operation of the retractable hardtop. The retractable hardtop will not operate if the trunk cargo cover is not in place. If the retractable hardtop is lowered or raised multiple times, the engine should be running while doing so to prevent drain on the vehicle’s battery. {CAUTION: Moving parts of the retractable hardtop can be dangerous. People can be injured by the hardtop and its mechanism. Keep people away from your vehicle when you are lowering or raising the top. Lowering the Retractable Hardtop Notice: Leaving the retractable hardtop down and exposing the interior of your vehicle to outdoor conditions may cause damage. Always close the retractable hardtop if leaving your vehicle outdoors. Notice: Raising or lowering the top while the vehicle is in motion can cause damage to the top or top mechanism. Make sure the vehicle is in PARK (P) to lower or raise the top. Notice: Lowering the top if it is damp, wet, or dirty can cause stains, mildew, and damage to the inside of your vehicle. Dry off the top before lowering it. 2-49 5. Push and hold the bottom of the retractable hardtop button located on the headliner, between the front reading lamps. The windows will automatically lower and the top will automatically lower into the storage area. A chime will sound when the top has lowered completely. If the radio is on, the sound may be muted brieﬂy while the retracable top is lowered. This is due to the audio equalization system re-loading. Under certain conditions, the Driver Information Center (DIC) may display a message regarding the retractable hardtop. If this happens, see DIC Warnings and Messages on page 3-48 for more information. If you lower the retractable hardtop in cold Notice: weather (0°F/−18°C or lower), you may damage top components. Do not lower the retractable hardtop in cold weather. 1. Park on a level surface and shift the automatic transaxle into PARK (P), or a manual transaxle into NEUTRAL with the parking brake set. 2. The vehicle’s engine must be on or turned to ACC, the trunk cargo cover must be in place, and the trunk must be closed. 3. Lower both sun visors. 4. Make sure that nothing or no one is on or around the top. Make sure there is nothing on top or in front of the cargo cover. {CAUTION: Moving parts of the retractable hardtop can be dangerous. People can be injured by the hardtop and its mechanism. Keep people away from your vehicle when you are lowering or raising the top. 2-50 Raising the Retractable Hardtop 1. Park on a level surface and shift the automatic transaxle into PARK (P), or a manual transaxle into NEUTRAL with the parking brake set. 2. The vehicle’s engine must be on or in ACC, and the trunk cargo cover must be in place. 3. Lower both sun visors. Notice: Raising or lowering the top while the vehicle is in motion can cause damage to the top or top mechanism. Make sure the vehicle is in PARK (P) to lower or raise the top. 4. Make sure nothing or no one is on or around the top. Make sure there is no cargo on top of or in front of the trunk cargo cover. {CAUTION: Moving parts of the retractable hardtop can be dangerous. People can be injured by the hardtop and its mechanism. Keep people away from your vehicle when you are lowering or raising the top. 5. Push and hold the top of the retractable hardtop button located on the headliner between the front reading lamps. The windows will automatically lower and the top will raise. A chime will sound when the top has raised completely. After the top is fully raised, release the retractable hardtop button. If you press the button again within ﬁve seconds, the windows will automatically close. If your radio is on, you may notice a brief mute in sound. This is normal and due to the audio system equalization re-loading for the vehicle with the top raised. Under certain conditions, the Driver Information Center (DIC) may display a message regarding the retractable hardtop. If this happens, see DIC Warnings and Messages on page 3-48 for more information. 2-51 ✍ NOTES 2-52 Section 3 Instrument Panel Instrument Panel Overview ...............................3-4 Hazard Warning Flashers ................................3-6 Other Warning Devices ...................................3-6 Horn .............................................................3-6 Tilt Wheel .....................................................3-6 Turn Signal/Multifunction Lever .........................3-7 Turn and Lane-Change Signals ........................3-8 Headlamp High/Low-Beam Changer ..................3-8 Flash-to-Pass .................................................3-8 Windshield Wipers ..........................................3-9 Windshield Washer .......................................3-10 Cruise Control ..............................................3-10 Headlamps ..................................................3-14 Headlamps on Reminder ................................3-14 Headlamps Off in PARK (P) ...........................3-14 Delayed Headlamps ......................................3-15 Daytime Running Lamps (DRL) .......................3-15 Automatic Headlamp System ..........................3-16 Fog Lamps ..................................................3-17 Instrument Panel Brightness ...........................3-17 Courtesy Lamps ...........................................3-17 Dome Lamp .................................................3-18 Entry/Exit Lighting .........................................3-18 Overhead Console Reading Lamps .................3-18 Trunk Lamp .................................................3-18 Battery Run-Down Protection ..........................3-18 Accessory Power Outlet(s) .............................3-19 Climate Controls ............................................3-20 Climate Control System .................................3-20 Automatic Climate Control System ...................3-23 Outlet Adjustment .........................................3-28 Warning Lights, Gages, and Indicators ............3-29 Instrument Panel Cluster ................................3-29 Speedometer and Odometer ...........................3-31 Trip Odometer ..............................................3-31 Tachometer .................................................3-31 Safety Belt Reminder Light .............................3-32 Passenger Safety Belt Reminder Light .............3-32 Airbag Readiness Light ..................................3-33 Passenger Airbag Status Indicator ...................3-34 Charging System Light ..................................3-36 Brake System Warning Light ..........................3-36 Anti-Lock Brake System Warning Light .............3-37 Traction Control System (TCS) Warning Light ...........................................3-38 Traction Control System Active Light ...............3-38 Enhanced Traction System Warning Light .........3-38 Enhanced Traction System Active Light ............3-39 StabiliTrak® Not Ready Light ..........................3-39 StabiliTrak® Indicator Light ..............................3-39 Engine Coolant Temperature Gage ..................3-40 Malfunction Indicator Lamp .............................3-40 Oil Pressure Light .........................................3-43 3-1 Section 3 Instrument Panel Security Light ...............................................3-44 Cruise Control Light ......................................3-44 Highbeam On Light .......................................3-44 Service Vehicle Soon Light ............................3-44 Fuel Gage ...................................................3-45 Low Fuel Warning Light .................................3-45 Driver Information Center (DIC) .......................3-45 DIC Operation and Displays ...........................3-46 DIC Warnings and Messages .........................3-48 DIC Vehicle Personalization ............................3-52 Audio System(s) .............................................3-54 Setting the Time for Radios without Radio Data Systems (RDS) ........................3-55 Setting the Time for Radios with Radio Data Systems (RDS) ........................3-55 Radio with CD (Base Level) ...........................3-56 Radio with CD (Up Level) ..............................3-61 Radio with Six-Disc CD .................................3-71 Theft-Deterrent Feature ..................................3-86 Audio Steering Wheel Controls (Three Spoke) ...........................................3-86 Audio Steering Wheel Controls (Four Spoke) ............................................3-87 Radio Reception ...........................................3-87 Care of Your CDs and DVDs .........................3-88 Care of the CD and DVD Player .....................3-88 Fixed Mast Antenna (Retractable Hardtop) .................................3-88 Backglass Antenna .......................................3-89 XM™ Satellite Radio Antenna System .............3-89 3-2 ✍ NOTES 3-3 Instrument Panel Overview 3-4 The main components of your instrument panel are the following: A. Side Air Outlets. See Outlet Adjustment on page 3-28. M. Instrument Panel Brightness Control. See Instrument Panel Brightness on page 3-17. B. Side Window Outlets. See Outlet Adjustment on page 3-28. C. Turn Signal/Multifunction Lever. See Turn Signal/Multifunction Lever on page 3-7. D. Cruise Controls (If Equipped). See Cruise Control on page 3-10. E. Instrument Panel Cluster. See Instrument Panel Cluster on page 3-29. F. Audio Steering Wheel Controls (If Equipped). See Audio Steering Wheel Controls (Three Spoke) on page 3-86 or Audio Steering Wheel Controls (Four Spoke) on page 3-87. G. Windshield Wiper and Washer Lever. See Windshield Wipers on page 3-9 and Windshield Washer on page 3-10. H. Ignition Switch. See Ignition Positions on page 2-23. I. Center Air Outlets. See Outlet Adjustment on page 3-28. J. Hazard Warning Flashers Button. See Hazard Warning Flashers on page 3-6. K. Audio System. See Audio System(s) on page 3-54. L. Adjustable Pedal Buttons (If Equipped). See Adjustable Throttle and Brake Pedal (Automatic Transaxle) on page 2-26. N. Fog Lamps (If Equipped). See Fog Lamps on page 3-17. O. Hood Release Handle. See Hood Release on page 5-11. P. Horn. See Horn on page 3-6. Q. Climate Control System. See Automatic Climate Control System on page 3-23 or Climate Control System on page 3-20. R. Shift Lever. See Automatic Transaxle Operation on page 2-28 or Manual Transaxle Operation on page 2-32. S. Accessory Power Outlet. See Accessory Power Outlet(s) on page 3-19. T. Traction Control System Button (If Equipped), Enhanced Traction System Button (If Equipped), and/or StabiliTrak® (If Equipped). See Traction Control System (TCS) on page 4-9 or Enhanced Traction System (ETS) on page 4-11 and/or StabiliTrak® System on page 4-12. U. Passenger Airbag Status Indicator. See Passenger Airbag Status Indicator on page 3-34. V. Glove Box. See Glove Box on page 2-45. 3-5 Hazard Warning Flashers Your hazard warning ﬂashers let you warn others. They also let police know you have a problem. Your front and rear turn signal lamps will ﬂash on and off. Other Warning Devices If you carry reﬂective triangles, you can set them up at the side of the road about 300 feet (100 m) behind your vehicle. The hazard warning ﬂasher button is located in the center of the instrument panel. Horn Press near or on the horn symbols on your steering wheel pad to sound the horn. Tilt Wheel A tilt and telescope wheel allows you to adjust the steering wheel before you drive. You can raise the steering wheel to the highest level to give your legs more room when you enter and exit the vehicle. Your hazard warning ﬂashers work no matter what position your key is in, and even if the key is not in. Press the button to make the front and rear turn signal lamps ﬂash on and off. Press the button again to turn the ﬂashers off. When the hazard warning ﬂashers are on, your turn signals will not work. 3-6 The lever that allows you to tilt and telescope the steering wheel is located on the left side of the steering column. Turn Signal/Multifunction Lever To tilt and telescope the wheel, pull down the lever. Then move the wheel to a comfortable position, pull up the lever to lock the wheel in place. The wheel can be adjusted up and down as well as forward and backward. The lever on the left side of the steering column includes the following: (cid:127) G Turn and Lane-Change Signals. See Turn and Lane-Change Signals on page 3-8. (cid:127) 3 Headlamp High/Low-Beam Changer. See Headlamp High/Low-Beam Changer on page 3-8. Flash-to-Pass. See Flash-to-Pass on page 3-8. (cid:127) 2 Exterior Light Control. See Headlamps on page 3-14. 3-7 (cid:127) Turn and Lane-Change Signals The turn signal has two upward (for right) and two downward (for left) positions. These positions allow you to signal a turn or a lane change. To signal a turn, move the lever all the way up or down. When the turn is ﬁnished, the lever will return automatically. An arrow on the instrument panel cluster will ﬂash in the direction of the turn or lane change. Headlamp High/Low-Beam Changer To change the headlamps from low beam to high beam, push the turn signal/multifunction lever away from you. When the high beams are on, a light on the instrument panel cluster also will be on if the ignition is in ON. To change the headlamps from high beam to low beam, pull the turn signal lever toward you. Flash-to-Pass

Boost Classifieds - Car Advice, Reviews, Events & Classifieds

2006 Pontiac G6 Owners Manual