Download PDF Manual

of that first. If you don’t, explosive gas could be present. Battery fluid contains acid that can burn you. Don’t get it on you. If you accidentally get it in your eyes or on your skin, flush the place with water and get medical help immediately.


5-5


6. Check that the jumper cables don’t have loose or


missing insulation. If they do, you could get a shock. The vehicles could be damaged, too.


Before you connect the cables, here are some basic things you should know. Positive (+) will go to positive (+) and negative (-) will go to a heavy, unpainted metal engine part. Don’t connect positive (+) to negative (-), or you’ll get a short that would damage the battery and maybe other parts, too. Don’t connect negative (-) to negative (-) on the dead battery, either, as this can cause sparks.


CAUTION:


Fans or other moving engine parts can injure you badly. Keep your hands away from moving parts once the engine is running.


5-6


7. Connect the red positive (+) cable to the positive (+)


terminal of the vehicle with the dead battery. Use a remote positive (+) terminal if the vehicle has one.


8. Don’t let the other end touch metal. Connect it to the


positive (+) terminal of the good battery. Use a remote positive (+) terminal if the vehicle has one.


5-7


9. Now connect the black negative (-) cable to the good


battery’s negative (-) terminal. Don’t let the other end touch anything until the next step. The other end of the negative cable doesn’t go to the dead battery. It goes to a heavy, unpainted, metal part on the engine of the vehicle with the dead battery.


10. Attach the cable at least 18 inches (45 cm) away


from the dead battery, but not near engine parts that move. The electrical connection is just as good there, but the chance of sparks getting back to the battery is much less.


11. Now start the vehicle with the good battery and run


the engine for a while.


12. Try to start the vehicle with the dead battery. If it won’t start after a few tries, it probably needs service.


5-8


13. Remove the cables in reverse order to prevent


electrical shorting. Take care that they don’t touch each other or any other metal.


Towing Your Vehicle


CAUTION:


A. Heavy, Unpainted Metal Engine Part B. Good Battery C. Dead Battery


To help avoid serious personal injury to you or others: D Never let passengers ride in a vehicle that is


being towed.


D Never tow faster than safe or posted speeds. D Never tow with damaged parts not


fully secured.


D Never get under your vehicle after it has


been lifted by the tow truck.


D Always secure the vehicle on each side with


separate safety chains when towing it.


D Use only the correct hooks.


NOTICE:


Use the proper towing equipment to avoid damage to the bumper, fascia or fog lamp areas of the vehicle.


5-9


With current trends in automotive styles and design, it is essential that the correct towing equipment is used to tow a vehicle. Your vehicle can be towed with wheel lift or car carrier equipment. Don’t have your vehicle towed on the drive wheels, unless you must. If the vehicle must be towed on the drive wheels, do not tow the vehicle more than 500 cumulative miles (800 km) or exceed 50 mph (80 km/h). If these limitations must be exceeded, then the drive wheels have to be supported on a dolly. Consult your dealer or a professional towing service if you need to have your vehicle towed. See “Roadside Assistance” in the Index. Engine Overheating You will find a coolant temperature gage and a warning light about a hot engine on your instrument panel. See “Engine Coolant Temperature Gage” in the Index. You also have a low coolant light on your instrument panel. See “Low Coolant Light” in the Index.


Overheated Engine Protection Operating Mode This emergency operating mode allows your vehicle to be driven to a safe place in an emergency situation. Should an overheated engine condition exist, an overheat protection mode which alternates firing groups of cylinders helps prevent engine damage. In this mode, you will notice a significant loss in power and engine performance. The low coolant light may come on and the temperature gage will indicate an overheat condition exists. Towing a trailer in the overheat protection mode should be avoided.


NOTICE:


After driving in the overheated engine protection operating mode, to avoid engine damage, allow the engine to cool before attempting any repair. The engine oil will be severely degraded. Repair the cause of coolant loss and change the oil. See “Engine Oil” in the Index.


5-10


If Steam Is Coming From Your Engine


CAUTION: (Continued)


the engine if you see or hear steam coming from it. Just turn it off and get everyone away from the vehicle until it cools down. Wait until there is no sign of steam or coolant before you open the hood. If you keep driving when your engine is overheated, the liquids in it can catch fire. You or others could be badly burned. Stop your engine if it overheats, and get out of the vehicle until the engine is cool. See “Overheated Engine Protection Operating Mode” in the Index.


CAUTION:


NOTICE:


Steam from an overheated engine can burn you badly, even if you just open the hood. Stay away


CAUTION: (Continued)


If your engine catches fire because you keep driving with no coolant, your vehicle can be badly damaged. The costly repairs would not be covered by your warranty. See “Overheated Engine Protection Operating Mode” in the Index.


5-11


If No Steam Is Coming From Your Engine If you get an engine overheat warning but see or hear no steam, the problem may not be too serious. Sometimes the engine can get a little too hot when you: D Climb a long hill on a hot day. D Stop after high-speed driving. D Idle for long periods in traffic. D Tow a trailer. If you get the overheat warning with no sign of steam, try this for a minute or so: 1. If your air conditioner is on, turn it off. 2. Turn on your heater to full hot at the highest fan


speed and open the window as necessary.


3. If you’re in a traffic jam, shift to NEUTRAL (N);


otherwise, shift to the highest gear while driving -- AUTOMATIC OVERDRIVE (D) or THIRD (3).


If you no longer have the overheat warning, you can drive. Just to be safe, drive slower for about 10 minutes. If the warning doesn’t come back on, you can drive normally. If the warning continues, pull over, stop, and park your vehicle right away. If there’s still no sign of steam, idle the engine for three minutes while you’re parked. If you still have the warning, turn off the engine and get everyone out of the vehicle until it cools down. Also, see “Overheated Engine Protection Operating Mode” listed previously in this section. You may decide not to lift the hood but to get service help right away.


5-12


Cooling System When you decide it’s safe to lift the hood, here’s what you’ll see:


CAUTION:


An electric engine cooling fan under the hood can start up even when the engine is not running and can injure you. Keep hands, clothing and tools away from any underhood electric fan.


If the coolant inside the coolant surge tank is boiling, don’t do anything else until it cools down.


A. Coolant Surge Tank B. Electric Engine Cooling Fans


5-13


CAUTION:


Heater and radiator hoses, and other engine parts, can be very hot. Don’t touch them. If you do, you can be burned. Don’t run the engine if there is a leak. If you run the engine, it could lose all coolant. That could cause an engine fire, and you could be burned. Get any leak fixed before you drive the vehicle.


When the engine is cold, the coolant level should be at or above the FULL COLD mark on the coolant surge tank. If it isn’t, you may have a leak in the radiator hoses, heater hoses, radiator, water pump or somewhere else in the cooling system.


5-14


NOTICE:


NOTICE:


Engine damage from running your engine without coolant isn’t covered by your warranty. See “Overheated Engine Protection Operating Mode” in the Index.


When adding coolant, it is important that you use only DEX-COOLR (silicate-free) coolant. If coolant other than DEX-COOL is added to the system, premature engine, heater core or radiator corrosion may result. In addition, the engine coolant will require change sooner -- at 30,000 miles (50 000 km) or 24 months, whichever occurs first. Damage caused by the use of coolant other than DEX-COOLR is not covered by your new vehicle warranty.


If there seems to be no leak, with the engine on, check to see if the electric engine cooling fans are running. If the engine is overheating, both fans should be running. If they aren’t, your vehicle needs service.


5-15


How to Add Coolant to the Coolant Surge Tank If you haven’t found a problem yet, but the coolant level isn’t at the FULL COLD mark, add a 50/50 mixture of clean, drinkable water and DEX-COOLR coolant at the coolant surge tank, but be sure the cooling system, including the coolant surge tank pressure cap, is cool before you do it. (See “Engine Coolant” in the Index for more information.)


CAUTION:


Steam and scalding liquids from a hot cooling system can blow out and burn you badly. They are under pressure, and if you turn the coolant surge tank pressure cap -- even a little -- they can come out at high speed. Never turn the cap when the cooling system, including the coolant surge tank pressure cap, is hot. Wait for the cooling system and coolant surge tank pressure cap to cool if you ever have to turn the pressure cap.


5-16


CAUTION:


NOTICE:


Adding only plain water to your cooling system can be dangerous. Plain water, or some other liquid like alcohol, can boil before the proper coolant mixture will. Your vehicle’s coolant warning system is set for the proper coolant mixture. With plain water or the wrong mixture, your engine could get too hot but you wouldn’t get the overheat warning. Your engine could catch fire and you or others could be burned. Use a 50/50 mixture of clean, drinkable water and DEX-COOLR coolant.


In cold weather, water can freeze and crack the engine, radiator, heater core and other parts. So use the recommended coolant.


CAUTION:


You can be burned if you spill coolant on hot engine parts. Coolant contains ethylene glycol and it will burn if the engine parts are hot enough. Don’t spill coolant on a hot engine.


5-17


1. You can remove the coolant surge tank pressure cap when the cooling system, including the coolant surge tank pressure cap and upper radiator hose, is no longer hot.


Turn the pressure cap slowly counterclockwise (left) about one-quarter turn and then stop. If you hear a hiss, wait for that to stop. A hiss means there is still some pressure left.


2. Then keep turning the pressure cap slowly, and


remove it.


5-18


3. Then fill the coolant surge tank with the proper


mixture, to the FULL COLD mark.


4. With the coolant surge tank pressure cap off, start the


engine and let it run until you can feel the upper radiator hose getting hot. Watch out for the engine cooling fans. By this time, the coolant level inside the coolant surge tank may be lower. If the level is lower, add more of the proper mixture to the coolant surge tank until the level reaches the FULL COLD mark.


5-19


If a Tire Goes Flat It’s unusual for a tire to “blow out” while you’re driving, especially if you maintain your tires properly. If air goes out of a tire, it’s much more likely to leak out slowly. But if you should ever have a “blowout,” here are a few tips about what to expect and what to do: If a front tire fails, the flat tire will create a drag that pulls the vehicle toward that side. Take your foot off the accelerator pedal and grip the steering wheel firmly. Steer to maintain lane position, and then gently brake to a stop well out of the traffic lane. A rear blowout, particularly on a curve, acts much like a skid and may require the same correction you’d use in a skid. In any rear blowout, remove your foot from the accelerator pedal. Get the vehicle under control by steering the way you want the vehicle to go. It may be very bumpy and noisy, but you can still steer. Gently brake to a stop -- well off the road if possible. If a tire goes flat, the next part shows how to use your jacking equipment to change a flat tire safely.


5. Then replace the pressure cap. Be sure the pressure


cap is hand-tight.


5-20


Changing a Flat Tire If a tire goes flat, avoid further tire and wheel damage by driving slowly to a level place. Turn on your hazard warning flashers.


CAUTION:


Changing a tire can cause an injury. The vehicle can slip off the jack and roll over you or other people. You and they could be badly injured. Find a level place to change your tire. To help prevent the vehicle from moving:


1. Set the parking brake firmly. 2. Put the shift lever in PARK (P). 3. Turn off the engine.


To be even more certain the vehicle won’t move, you can put blocks at the front and rear of the tire farthest away from the one being changed. That would be the tire on the other side of the vehicle, at the opposite end.


The following steps will tell you how to use the jack and change a tire.


5-21


Removing the Spare Tire and Tools


The equipment you’ll need is in the trunk.


Turn the center nut on the compact spare cover counterclockwise to remove it. Then lift and remove the cover.


Remove the spare tire. See “Compact Spare Tire” in the Index for more information about the compact spare.


5-22


Turn the nut holding the jack counterclockwise and remove it. Then remove the jack and wrench.


The tools you’ll be using include the jack (A), extension and protector/guide (B) and wheel wrench (C).


5-23


Removing the Flat Tire and Installing the Spare Tire


CAUTION:


Getting under a vehicle when it is jacked up is dangerous. If the vehicle slips off the jack, you could be badly injured or killed. Never get under a vehicle when it is supported only by a jack.


CAUTION:


Raising your vehicle with the jack improperly positioned can damage the vehicle and even make the vehicle fall. To help avoid personal injury and vehicle damage, be sure to fit the jack lift head into the proper location before raising the vehicle.


1. Using the wheel wrench, remove the plastic caps and loosen all of the wheel nuts. Don’t remove them yet.


5-24


2. Turn the jack handle clockwise to raise the jack lift


head a few inches.


For jacking at the vehicle’s front location, put the jack lift head about 8 inches (20 cm) from the rear edge of the front wheel opening or just behind the two bolts as shown.


For jacking at the vehicle’s rear location, put the jack lift head about 6 inches (15 cm) from the front edge of the rear wheel opening or just behind the off-set as shown. Put the compact spare tire near you.


5-25


3. Raise the vehicle by turning the jack handle


clockwise. Raise the vehicle far enough off the ground for the spare tire to fit under the vehicle.


4. Remove all wheel nuts and take off the flat tire.


5-26


5. Remove any rust or dirt


from the wheel bolts, mounting surfaces and spare wheel.


CAUTION:


Rust or dirt on the wheel, or on the parts to which it is fastened, can make the wheel nuts become loose after a time. The wheel could come off and cause an accident. When you change a wheel, remove any rust or dirt from the places where the wheel attaches to the vehicle. In an emergency, you can use a cloth or a paper towel to do this; but be sure to use a scraper or wire brush later, if you need to, to get all the rust or dirt off.


CAUTION:


Never use oil or grease on studs or nuts. If you do, the nuts might come loose. Your wheel could fall off, causing a serious accident.


6. Install the spare tire.


Reinstall the wheel nuts with the rounded end of the nuts toward the wheel. Tighten each nut by hand until the wheel is held against the hub.


5-27


8. Tighten the wheel nuts


firmly in a crisscross sequence as shown.


7. Lower the vehicle by turning the jack handle counterclockwise. Lower the jack completely.


5-28


CAUTION:


NOTICE:


Incorrect wheel nuts or improperly tightened wheel nuts can cause the wheel to become loose and even come off. This could lead to an accident. Be sure to use the correct wheel nuts. If you have to replace them, be sure to get new GM original equipment wheel nuts. Stop somewhere as soon as you can and have the nuts tightened with a torque wrench to 100 lb-ft (140 N·m).


Improperly tightened wheel nuts can lead to brake pulsation and rotor damage. To avoid expensive brake repairs, evenly tighten the wheel nuts in the proper sequence and to the proper torque specification.


9. Replace the plastic caps tightly by hand.


Using the wheel wrench, tighten caps an additional one quarter turn.


5-29


Storing the Flat Tire and Tools


CAUTION:


Storing a jack, a tire or other equipment in the passenger compartment of the vehicle could cause injury. In a sudden stop or collision, loose equipment could strike someone. Store all these in the proper place.


After you’ve put the compact spare tire on your vehicle, you’ll need to store the flat tire in your trunk. Use the following procedure to secure the flat tire in the trunk.


5-30


When storing a full-size tire, you must use the extension to help avoid wheel surface damage. Use the extension and protector/guide located in the foam holder. To store a full-size tire, place the tire in the trunk with the valve stem facing down and the protector/guide through a wheel bolt hole. Remove the protector and attach the retainer securely. When reinstalling the compact spare, put the protector/guide back in the foam holder. Store the cover as far forward as possible.


Storing the Spare Tire and Tools


CAUTION:


Storing a jack, a tire or other equipment in the passenger compartment of the vehicle could cause injury. In a sudden stop or collision, loose equipment could strike someone. Store all these in the proper place.


The compact spare is for temporary use only. Replace the compact spare tire with a full-size tire as soon as you can. See “Compact Spare Tire” in the Index. See the storage instructions label to replace your compact spare into your trunk properly.


A. Retainer B. Cover C. Compact Spare Tire D. Nut E. Jack F. Wrench G. Lock Nut Tool H. Foam Holder I. Extension and


Protective Guide


J. Bolt Screw


5-31


Compact Spare Tire Although the compact spare tire was fully inflated when your vehicle was new, it can lose air after a time. Check the inflation pressure regularly. It should be 60 psi (420 kPa). After installing the compact spare on your vehicle, you should stop as soon as possible and make sure your spare tire is correctly inflated. The compact spare is made to perform well at speeds up to 65 mph (105 km/h) for distances up to 3,000 miles (5 000 km), so you can finish your trip and have your full-size tire repaired or replaced where you want. Of course, it’s best to replace your spare with a full-size tire as soon as you can. Your spare will last longer and be in good shape in case you need it again.


NOTICE:


When the compact spare is installed, don’t take your vehicle through an automatic car wash with guide rails. The compact spare can get caught on the rails. That can damage the tire and wheel, and maybe other parts of your vehicle.


5-32


Don’t use your compact spare on other vehicles. And don’t mix your compact spare tire or wheel with other wheels or tires. They won’t fit. Keep your spare tire and its wheel together.


NOTICE:


Tire chains won’t fit your compact spare. Using them can damage your vehicle and can damage the chains too. Don’t use tire chains on your compact spare.


If You’re Stuck: In Sand, Mud, Ice or Snow In order to free your vehicle when it is stuck, you will need to spin the wheels, but you don’t want to spin your wheels too fast. The method known as “rocking” can help you get out when you’re stuck, but you must use caution.


CAUTION:


If you let your tires spin at high speed, they can explode, and you or others could be injured. And, the transaxle or other parts of the vehicle can overheat. That could cause an engine compartment fire or other damage. When you’re stuck, spin the wheels as little as possible. Don’t spin the wheels above 35 mph (55 km/h) as shown on the speedometer.


NOTICE:


Spinning your wheels can destroy parts of your vehicle as well as the tires. If you spin the wheels too fast while shifting your transaxle back and forth, you can destroy your transaxle.


For information about using tire chains on your vehicle, see “Tire Chains” in the Index.


Rocking Your Vehicle To Get It Out First, turn your steering wheel left and right. That will clear the area around your front wheels. If your vehicle has traction control, you should turn the system off. (See “Traction Control System” in the Index.) Then shift back and forth between REVERSE (R) and a forward gear, spinning the wheels as little as possible. Release the accelerator pedal while you shift, and press lightly on the accelerator pedal when the transaxle is in gear. By slowly spinning your wheels in the forward and reverse directions, you will cause a rocking motion that may free your vehicle. If that doesn’t get you out after a few tries, you may need to be towed out. If you do need to be towed out, see “Towing Your Vehicle” in the Index.


5-33


Section 6 Service and Appearance Care


Here you will find information about the care of your vehicle. This section begins with service and fuel information, and then it shows how to check important fluid and lubricant levels. There is also technical information about your vehicle, and a part devoted to its appearance care.


6-2
6-3
6-5
6-6
6-9
6-9
6-12
6-17
6-19


6-20
6-23
6-26
6-27
6-28
6-29
6-33


Service Fuel Fuels in Foreign Countries Filling Your Tank Filling a Portable Fuel Container Checking Things Under the Hood Engine Oil Engine Air Cleaner/Filter Passenger Compartment Air Filter (If Equipped) Automatic Transaxle Fluid Engine Coolant Cooling System Pressure Cap Power Steering Fluid Windshield Washer Fluid Brakes Battery


6-


6-33
6-41
6-42
6-49
6-50
6-52
6-53
6-55


6-56
6-57
6-58
6-58
6-58
6-66
6-66
6-67


Bulb Replacement Windshield Wiper Blade Replacement Tires Appearance Care Cleaning the Inside of Your Vehicle Care of Safety Belts Cleaning the Outside of Your Vehicle Cleaning Aluminum or Chrome-Plated Wheels (If Equipped) Finish Damage GM Vehicle Care/Appearance Materials Vehicle Identification Number (VIN) Service Parts Identification Label Electrical System Replacement Bulbs Capacities and Specifications Normal Maintenance Replacement Parts


6-1


Service Your dealer knows your vehicle best and wants you to be happy with it. We hope you’ll go to your dealer for all your service needs. You’ll get genuine GM parts and GM-trained and supported service people. We hope you’ll want to keep your GM vehicle all GM. Genuine GM parts have one of these marks:


Doing Your Own Service Work If you want to do some of your own service work, you’ll want to use the proper service manual. It tells you much more about how to service your vehicle than this manual can. To order the proper service manual, see “Service and Owner Publications” in the Index. Your vehicle has an air bag system. Before attempting to do your own service work, see “Servicing Your Air Bag-Equipped Vehicle” in the Index. You should keep a record with all parts receipts and list the mileage and the date of any service work you perform. See “Maintenance Record” in the Index.


6-2


CAUTION:


You can be injured and your vehicle could be damaged if you try to do service work on a vehicle without knowing enough about it. D Be sure you have sufficient knowledge,


experience, the proper replacement parts and tools before you attempt any vehicle maintenance task.


D Be sure to use the proper nuts, bolts and other fasteners. “English” and “metric” fasteners can be easily confused. If you use the wrong fasteners, parts can later break or fall off. You could be hurt.


Adding Equipment to the Outside of Your Vehicle Things you might add to the outside of your vehicle can affect the airflow around it. This may cause wind noise and affect windshield washer performance. Check with your dealer before adding equipment to the outside of your vehicle.


Fuel Use regular unleaded gasoline rated at 87 octane or higher. It is recommended that the gasoline meet specifications which have been developed by the American Automobile Manufacturers Association (AAMA) and endorsed by the Canadian Motor Vehicle Manufacturers Association for better vehicle performance and engine protection. Gasolines meeting the AAMA specification could provide improved driveability and emission control system performance compared to other gasolines. Be sure the posted octane is at least 87. If the octane is less than 87, you may get a heavy knocking noise when you drive. If it’s bad enough, it can damage your engine. If you’re using fuel rated at 87 octane or higher and you hear heavy knocking, your engine needs service. But don’t worry if you hear a little pinging noise when you’re accelerating or driving up a hill. That’s normal, and you don’t have to buy a higher octane fuel to get rid of pinging. It’s the heavy, constant knock that means you have a problem.


6-3


If your vehicle is certified to meet California Emission Standards (indicated on the underhood emission control label), it is designed to operate on fuels that meet California specifications. If such fuels are not available in states adopting California emissions standards, your vehicle will operate satisfactorily on fuels meeting federal specifications, but emission control system performance may be affected. The malfunction indicator lamp on your instrument panel may turn on and/or your vehicle may fail a smog-check test. (See “Malfunction Indicator Lamp” in the Index.) If this occurs, return to your authorized Oldsmobile dealer for diagnosis to determine the cause of failure. In the event it is determined that the cause of the condition is the type of fuels used, repairs may not be covered by your warranty.


Some gasolines that are not reformulated for low emissions may contain an octane-enhancing additive called methylcyclopentadienyl manganese tricarbonyl (MMT); ask your service station operator whether or not the fuel contains MMT. General Motors does not recommend the use of such gasolines. If fuels containing MMT are used, spark plug life may be reduced and your emission control system performance may be affected. The malfunction indicator lamp on your instrument panel may turn on. If this occurs, return to your authorized Oldsmobile dealer for service.


6-4


To provide cleaner air, all gasolines in the United States are now required to contain additives that will help prevent deposits from forming in your engine and fuel system, allowing your emission control system to function properly. Therefore, you should not have to add anything to the fuel. In addition, gasolines containing oxygenates, such as ethers and ethanol, and reformulated gasolines may be available in your area to contribute to clean air. General Motors recommends that you use these gasolines, particularly if they comply with the specifications described earlier.


NOTICE:


Your vehicle was not designed for fuel that contains methanol. Don’t use it. It can corrode metal parts in your fuel system and also damage plastic and rubber parts. That damage wouldn’t be covered under your warranty.


Fuels in Foreign Countries If you plan on driving in another country outside the United States or Canada, the proper fuel may be hard to find. Never use leaded gasoline or any other fuel not recommended in the previous text on fuel. Costly repairs caused by use of improper fuel wouldn’t be covered by your warranty. To check on fuel availability, ask an auto club, or contact a major oil company that does business in the country where you’ll be driving. You can also write us at the following address for advice. Just tell us where you’re going and give your Vehicle Identification Number (VIN).


General Motors Overseas Distribution Corporation 1908 Colonel Sam Drive Oshawa, Ontario L1H 8P7


6-5


Filling Your Tank


CAUTION:


Gasoline vapor is highly flammable. It burns violently, and that can cause very bad injuries. Don’t smoke if you’re near gasoline or refueling your vehicle. Keep sparks, flames and smoking materials away from gasoline.


The button for the fuel door is located on the instrument panel, to the left of the steering column.


If your fuel filler door release won’t operate, there is a manual release tab. The tab is located in the trunk, against the trim on the driver’s side of the vehicle.


The tethered cap is located behind a hinged door on the driver’s side of your vehicle. 6-6


NOTICE:


Prying on a locked fuel filler door can damage it. Use the remote fuel door manual release located in the trunk to release the door.


While refueling, let the cap hang by the tether below the fuel fill opening. To remove the cap, turn it slowly to the left (counterclockwise). The cap has a spring in it; if you let go of the cap too soon, it will spring back to the right.


6-7


CAUTION:


If you get gasoline on yourself and then something ignites it, you could be badly burned. Gasoline can spray out on you if you open the fuel filler cap too quickly. This spray can happen if your tank is nearly full, and is more likely in hot weather. Open the fuel filler cap slowly and wait for any “hiss” noise to stop. Then unscrew the cap all the way.


Be careful not to spill gasoline. Clean gasoline from painted surfaces as soon as possible. See “Cleaning the Outside of Your Vehicle” in the Index.


When you put the cap back on, turn it to the right (clockwise) until you hear a clicking sound. Make sure you fully install the cap. The diagnostic system can determine if the fuel cap has been left off or improperly installed. This would allow fuel to evaporate into the atmosphere. See “Malfunction Indicator Lamp” in the Index.


NOTICE:


If you need a new cap, be sure to get the right type. Your dealer can get one for you. If you get the wrong type, it may not fit properly. This may cause your malfunction indicator lamp to light and your fuel tank and emissions system may be damaged. See “Malfunction Indicator Lamp” in the Index.


6-8


Filling a Portable Fuel Container


Checking Things Under the Hood


CAUTION:


CAUTION:


Never fill a portable fuel container while it is in your vehicle. Static electricity discharge from the container can ignite the gasoline vapor. You can be badly burned and your vehicle damaged if this occurs. To help avoid injury to you and others: D Dispense gasoline only into


approved containers.


D Do not fill a container while it is inside a


vehicle, in a vehicle’s trunk, pickup bed or on any surface other than the ground. D Bring the fill nozzle in contact with the


inside of the fill opening before operating the nozzle. Contact should be maintained until the filling is complete.


D Don’t smoke while pumping gasoline.


An electric fan under the hood can start up and injure you even when the engine is not running. Keep hands, clothing and tools away from any underhood electric fan.


CAUTION:


Things that burn can get on hot engine parts and start a fire. These include liquids like gasoline, oil, coolant, brake fluid, windshield washer and other fluids, and plastic or rubber. You or others could be burned. Be careful not to drop or spill things that will burn onto a hot engine.


6-9


Hood Release


To open the hood, first pull the handle inside the vehicle. It is located below the instrument panel on the driver’s side.


Then go to the front of the vehicle and release the secondary hood release. Lift the hood.


6-10


When you open the hood of the 3.5L V6 engine, you’ll see:


A. Windshield Washer


Fluid Reservoir


B. California Emissions Fuse


Block (If Equipped)


C. Battery


D. Remote Positive (+) Terminal E. Engine Coolant Surge Tank F. Power Steering Fluid Reservoir G. Engine Oil Fill Cap H. Engine Oil Dipstick


I. Automatic Transaxle


Fluid Dipstick


J. Brake Fluid Reservoir K. Engine Air Cleaner/Filter


6-11


Before closing the hood, be sure that all the filler caps are on properly. Then pull the hood down and close it firmly. Engine Oil


Checking Engine Oil It’s a good idea to check your engine oil every time you get fuel. In order to get an accurate reading, the oil must be warm and the vehicle must be on level ground.


If the LOW OIL message appears on the instrument panel, it means you need to check your engine oil level right away. For more information, see “Low Oil Light” in the Index.


You should check your engine oil level regularly; this is an added reminder.


The engine oil dipstick is the yellow loop located near the front of the engine.


Turn off the engine and give the oil several minutes to drain back into the oil pan. If you don’t, the oil dipstick might not show the actual level. Pull out the dipstick and clean it with a paper towel or cloth, then push it back in all the way. Remove it again, keeping the tip down, and check the level.


6-12


When to Add Engine Oil If the oil is at or below the ADD mark, then you’ll need to add at least one quart of oil. But you must use the right kind. This part explains what kind of oil to use. For crankcase capacity, see “Capacities and Specifications” in the Index.


NOTICE:


Don’t add too much oil. If your engine has so much oil that the oil level gets above the FULL mark that shows the proper operating range, your engine could be damaged.


The engine oil fill cap is located toward the front of the engine compartment near the yellow looped engine oil dipstick.


Be sure to fill it enough to put the level somewhere in the proper operating range. Push the dipstick all the way back in when you’re through.


6-13


What Kind of Engine Oil to Use Oils recommended for your vehicle can be identified by looking for the starburst symbol. This symbol indicates that the oil has been certified by the American Petroleum Institute (API). Do not use any oil which does not carry this starburst symbol.


If you change your own oil, be sure you use oil that has the starburst symbol on the front of the oil container. If you have your oil changed for you, be sure the oil put into your engine is American Petroleum Institute certified for gasoline engines.


You should also use the proper viscosity oil for your vehicle, as shown in the following chart:


6-14


As shown in the chart, SAE 5W-30 is best for your vehicle. However, you can use SAE 10W-30 if it’s going to be 0_F (-18_C) or above. These numbers on an oil container show its viscosity, or thickness. Do not use other viscosity oils, such as SAE 20W-50.


NOTICE:


Use only engine oil with the American Petroleum Institute Certified For Gasoline Engines starburst symbol. Failure to use the recommended oil can result in engine damage not covered by your warranty.


GM GoodwrenchR oil meets all the requirements for your vehicle. If you are in an area where the temperature falls below -20_F (-29_C), consider using either an SAE 5W-30
synthetic oil or an SAE 0W-30 oil. Both will provide easier cold starting and better protection for your engine at extremely low temperatures.


Engine Oil Additives Don’t add anything to your oil. The recommended oils with the starburst symbol are all you will need for good performance and engine protection. When to Change Engine Oil Your vehicle has a computer that lets you know when to change your engine oil. This is not based on mileage, but on engine revolutions and engine operating temperature. When the computer has calculated that the oil needs changing, the GM Oil Life Systemt will indicate that a change is necessary. The mileage between oil and filter changes will vary depending on how you drive your vehicle -- usually between 3,000 miles (5 000 km) and 7,500 miles (12 500 km) since your last oil and filter change. Under severe conditions, the system may come on before 3,000 miles (5 000 km). Never drive your vehicle more than 7,500 miles (12 500 km) or 12 months (whichever occurs first) without an oil change. The system won’t detect dust in the oil. So, if you drive in a dusty area, be sure to change your oil and filter every 3,000 miles (5 000 km) or sooner. Remember to reset the CHANGE OIL light whenever the oil is changed.


6-15


How to Reset the CHANGE OIL Light After changing the engine oil, the system must be reset. To reset the CHANGE OIL light after an oil change: 1. With the ignition key turned to the ON position but the engine off, fully push and release the accelerator pedal slowly three times within five seconds. If the CHANGE OIL light flashes, the system is resetting.


2. Turn the key to OFF after the light has finished


flashing, then start the vehicle. If the CHANGE OIL light comes back on, the engine oil life system has not reset. Repeat the procedure.


What to Do with Used Oil Did you know that used engine oil contains certain elements that may be unhealthy for your skin and could even cause cancer? Don’t let used oil stay on your skin for very long. Clean your skin and nails with soap and water, or a good hand cleaner. Wash or properly throw away clothing or rags containing used engine oil. (See the manufacturer’s warnings about the use and disposal of oil products.) Used oil can be a real threat to the environment. If you change your own oil, be sure to drain all free-flowing oil from the filter before disposal. Don’t ever dispose of oil by putting it in the trash, pouring it on the ground, into sewers, or into streams or bodies of water. Instead, recycle it by taking it to a place that collects used oil. If you have a problem properly disposing of your used oil, ask your dealer, a service station or a local recycling center for help.


6-16


Engine Air Cleaner/Filter To check or replace the air cleaner/filter:


1. Using a screwdriver, loosen the bolt on the air duct


clamp from the throttle body.


2. Remove the air duct from the throttle body.


3. Unhook the two hold down clips located on the air


box cover.


4. Lift the air box cover and air duct assembly away


from the air box, toward the engine.


6-17


5. Hold the air box cover and air duct assembly up in position while removing the air filter element from the air box.


6. To install the air cleaner/filter, reverse the steps.


Be sure the tabs on the cover are inserted into the air box slots. Refer to the Maintenance Schedule to determine when to replace the air filter. See “Scheduled Maintenance Services” in the Index.


6-18


CAUTION:


Operating the engine with the air cleaner/filter off can cause you or others to be burned. The air cleaner not only cleans the air, it stops flame if the engine backfires. If it isn’t there, and the engine backfires, you could be burned. Don’t drive with it off, and be careful working on the engine with the air cleaner/filter off.


NOTICE:


If the air cleaner/filter is off, a backfire can cause a damaging engine fire. And, dirt can easily get into your engine, which will damage it. Always have the air cleaner/filter in place when you’re driving.


Passenger Compartment Air Filter (If Equipped)


The passenger compartment air filter is located underneath the hood just below the windshield wiper arm on the passenger’s side of the vehicle (underneath the air inlet grille). The filter traps most of the pollen from air entering the module. Like your engine’s air cleaner/filter, it may need to be changed periodically. For information on how often to change the passenger compartment air filter, see “Maintenance Schedule” in the Index.


6-19


To change the passenger compartment air filter, use the following steps: 1. Turn off the ignition when the windshield wipers are


in the up position.


2. Raise the hood. 3. Disconnect the windshield washer pump hose from


the fender rail and air inlet grille.


4. Reposition the hood weatherstrip from the right side


of the vehicle (peel back halfway to center).


5. Remove the air inlet grille retainers. 6. Remove the air inlet grille. 7. Remove the air deflector grille in the compartment. 8. Remove the passenger compartment air filter. 9. Then reverse the steps to install the new air filter.


6-20


Automatic Transaxle Fluid When to Check and Change A good time to check your automatic transaxle fluid level is when the engine oil is changed. Change both the fluid and filter every 50,000 miles (83 000 km) if the vehicle is mainly driven under one or more of these conditions: D In heavy city traffic where the outside temperature


regularly reaches 90_F (32_C) or higher.


D In hilly or mountainous terrain. D When doing frequent trailer towing. D Uses such as found in taxi, police or delivery service. If you do not use your vehicle under any of these conditions, change the fluid and filter at 100,000 miles (166 000 km). See “Scheduled Maintenance Services” in the Index. How to Check Because this operation can be a little difficult, you may choose to have this done at the dealership service department. If you do it yourself, be sure to follow all the instructions here, or you could get a false reading on the dipstick.


NOTICE:


Too much or too little fluid can damage your transaxle. Too much can mean that some of the fluid could come out and fall on hot engine parts or exhaust system parts, starting a fire. Be sure to get an accurate reading if you check your transaxle fluid.


Wait at least 30 minutes before checking the transaxle fluid level if you have been driving: D When outside temperatures are above 90_F (32_C). D At high speed for quite a while. D In heavy traffic -- especially in hot weather. D While pulling a trailer. To get the right reading, the fluid should be at normal operating temperature, which is 180_F to 200_F (82_C to 93_C). Get the vehicle warmed up by driving about 15 miles (24 km) when outside temperatures are above 50_F (10_C). If it’s colder than 50_F (10_C), you may have to drive longer.


Checking the Fluid Level Prepare your vehicle as follows: D Park your vehicle on a level place. Keep the


engine running.


D With the parking brake applied, place the shift lever


in PARK (P).


D With your foot on the brake pedal, move the shift lever through each gear range, pausing for about three seconds in each range. Then, position the shift lever in PARK (P).


D Let the engine run at idle for three to five minutes. Then, without shutting off the engine, follow these steps:


1. The transaxle fluid dipstick is the red loop near the rear of the engine compartment. Pull out the dipstick and wipe it with a clean rag or paper towel.


6-21


2. Push it back in all the way, wait three seconds and


then pull it back out again.


3. Check both sides of the dipstick, and read the


lower level. The fluid level must be in the cross-hatched area.


4. If the fluid level is in the acceptable range, push the


dipstick back in all the way.


How to Add Fluid Refer to the Maintenance Schedule to determine what kind of transaxle fluid to use. See “Recommended Fluids and Lubricants” in the Index.


6-22


If the fluid level is low, add only enough of the proper fluid to bring the level into the cross-hatched area on the dipstick. 1. Pull out the dipstick. 2. Using a long-neck funnel, add enough fluid at the


dipstick hole to bring it to the proper level. It doesn’t take much fluid, generally less than one pint (0.5 L). Don’t overfill.


NOTICE:


We recommend you use only fluid labeled DEXRONR-III, because fluid with that label is made especially for your automatic transaxle. Damage caused by fluid other than DEXRONR-III is not covered by your new vehicle warranty.


3. After adding fluid, recheck the fluid level as


described under “How to Check.”


4. When the correct fluid level is obtained, push the


dipstick back in all the way.


Engine Coolant The cooling system in your vehicle is filled with DEX-COOLR engine coolant. This coolant is designed to remain in your vehicle for 5 years or 150,000 miles (240 000 km), whichever occurs first, if you add only DEX-COOLR extended life coolant. The following explains your cooling system and how to add coolant when it is low. If you have a problem with engine overheating or if you need to add coolant to your radiator, see “Engine Overheating” in the Index. A 50/50 mixture of clean, drinkable water and DEX-COOLR coolant will: D Give freezing protection down to -34_F (-37_C). D Give boiling protection up to 265_F (129_C). D Protect against rust and corrosion. D Help keep the proper engine temperature. D Let the warning lights and gages work as


they should.


NOTICE:


When adding coolant, it is important that you use only DEX-COOLR (silicate-free) coolant. If coolant other than DEX-COOL is added to the system, premature engine, heater core or radiator corrosion may result. In addition, the engine coolant will require change sooner -- at 30,000 miles (50 000 km) or 24 months, whichever occurs first. Damage caused by the use of coolant other than DEX-COOLR is not covered by your new vehicle warranty.


6-23


What to Use Use a mixture of one-half clean, drinkable water and one-half DEX-COOLR coolant which won’t damage aluminum parts. If you use this coolant mixture, you don’t need to add anything else.


CAUTION:


Adding only plain water to your cooling system can be dangerous. Plain water, or some other liquid like alcohol, can boil before the proper coolant mixture will. Your vehicle’s coolant warning system is set for the proper coolant mixture. With plain water or the wrong mixture, your engine could get too hot but you wouldn’t get the overheat warning. Your engine could catch fire and you or others could be burned. Use a 50/50 mixture of clean, drinkable water and DEX-COOLR coolant.


NOTICE:


If you use an improper coolant mixture, your engine could overheat and be badly damaged. The repair cost wouldn’t be covered by your warranty. Too much water in the mixture can freeze and crack the engine, radiator, heater core and other parts.


If you have to add coolant more than four times a year, have your dealer check your cooling system.


NOTICE:


If you use the proper coolant, you don’t have to add extra inhibitors or additives which claim to improve the system. These can be harmful.


6-24


Checking Coolant


The coolant surge tank is located in the engine compartment toward the rear of the engine on the passengers’ side of the vehicle.


CAUTION:


Turning the surge tank pressure cap when the engine and radiator are hot can allow steam and scalding liquids to blow out and burn you badly. Never turn the surge tank pressure cap -- even a little -- when the engine and radiator are hot.


The vehicle must be on a level surface. When your engine is cold, the coolant level should be at the FULL COLD mark.


If the low coolant warning light comes on and stays on, it means you’re low on engine coolant.


6-25


Adding Coolant If you need more coolant, add the proper DEX-COOLR coolant mixture at the surge tank, but only when the engine is cool.


Cooling System Pressure Cap The cooling system pressure cap is located on the surge tank.


CAUTION:


You can be burned if you spill coolant on hot engine parts. Coolant contains ethylene glycol, and it will burn if the engine parts are hot enough. Don’t spill coolant on a hot engine.


When replacing the pressure cap, make sure it is hand-tight.


NOTICE:


Your cooling system pressure cap is a 15 psi (105 kPa) pressure-type cap and must be tightly installed to prevent coolant loss and possible engine damage from overheating.


6-26


Power Steering Fluid


The power steering fluid reservoir is toward the middle of the engine compartment, on the passenger’s side.


When to Check Power Steering Fluid It is not necessary to regularly check power steering fluid unless you suspect there is a leak in the system or you hear an unusual noise. A fluid loss in this system could indicate a problem. Have the system inspected and repaired. How to Check Power Steering Fluid Turn the key off, let the engine compartment cool down, wipe the cap and the top of the reservoir clean, then unscrew the cap and wipe the dipstick with a clean rag. Replace the cap and completely tighten it. Then remove the cap again and look at the fluid level on the dipstick.


The level should be at the the cross-hatched area. If necessary, add only enough fluid to bring the level up to the mark. What to Use To determine what kind of fluid to use, see “Recommended Fluids and Lubricants” in the Index. Always use the proper fluid. Failure to use the proper fluid can cause leaks and damage hoses and seals.


6-27


Windshield Washer Fluid What to Use When you need windshield washer fluid, be sure to read the manufacturer’s instructions before use. If you will be operating your vehicle in an area where the temperature may fall below freezing, use a fluid that has sufficient protection against freezing. Adding Washer Fluid


If the windshield washer fluid level in your vehicle is low, the LOW WASHER FLUID warning light on the instrument panel will come on. You will need to add fluid soon.


6-28


Open the cap labeled WASHER FLUID ONLY. Add washer fluid until the tank is full.


NOTICE:


D When using concentrated washer fluid,


follow the manufacturer’s instructions for adding water.


D Don’t mix water with ready-to-use washer fluid. Water can cause the solution to freeze and damage your washer fluid tank and other parts of the washer system. Also, water doesn’t clean as well as washer fluid.


D Fill your washer fluid tank only


three-quarters full when it’s very cold. This allows for expansion if freezing occurs, which could damage the tank if it is completely full.


D Don’t use engine coolant (antifreeze) in your windshield washer. It can damage your washer system and paint.


Brakes Brake Fluid


Your brake master cylinder reservoir is on the driver’s side of the engine compartment. It is filled with DOT-3
brake fluid.


6-29


There are only two reasons why the brake fluid level in the reservoir might go down. The first is that the brake fluid goes down to an acceptable level during normal brake lining wear. When new linings are put in, the fluid level goes back up. The other reason is that fluid is leaking out of the brake system. If it is, you should have your brake system fixed, since a leak means that sooner or later your brakes won’t work well, or won’t work at all. So, it isn’t a good idea to “top off” your brake fluid. Adding brake fluid won’t correct a leak. If you add fluid when your linings are worn, then you’ll have too much fluid when you get new brake linings. You should add (or remove) brake fluid, as necessary, only when work is done on the brake hydraulic system.


CAUTION:


If you have too much brake fluid, it can spill on the engine. The fluid will burn if the engine is hot enough. You or others could be burned, and your vehicle could be damaged. Add brake fluid only when work is done on the brake hydraulic system.


When your brake fluid falls to a low level, your brake warning light will come on. See “Brake System Warning Light” in the Index.


What to Add When you do need brake fluid, use only DOT-3 brake fluid. Use new brake fluid from a sealed container only. Refer to “Recommended Fluids and Lubricants” in the Maintenance Schedule. Always clean the brake fluid reservoir cap and the area around the cap before removing it. This will help keep dirt from entering the reservoir.


CAUTION:


With the wrong kind of fluid in your brake system, your brakes may not work well, or they may not even work at all. This could cause a crash. Always use the proper brake fluid.


6-30


NOTICE:


CAUTION:


D Using the wrong fluid can badly damage


brake system parts. For example, just a few drops of mineral-based oil, such as engine oil, in your brake system can damage brake system parts so badly that they’ll have to be replaced. Don’t let someone put in the wrong kind of fluid.


D If you spill brake fluid on your vehicle’s painted surfaces, the paint finish can be damaged. Be careful not to spill brake fluid on your vehicle. If you do, wash it off immediately. See “Appearance Care” in the Index.


Brake Wear Your vehicle has four-wheel disc brakes. Disc brake pads have built-in wear indicators that make a high-pitched warning sound when the brake pads are worn and new pads are needed. The sound may come and go or be heard all the time your vehicle is moving (except when you are pushing on the brake pedal firmly).


The brake wear warning sound means that soon your brakes won’t work well. That could lead to an accident. When you hear the brake wear warning sound, have your vehicle serviced.


NOTICE:


Continuing to drive with worn-out brake pads could result in costly brake repair.


Some driving conditions or climates may cause a brake squeal when the brakes are first applied or lightly applied. This does not mean something is wrong with your brakes.


6-31


Properly torqued wheel nuts are necessary to help prevent brake pulsation. When tires are rotated, inspect brake pads for wear and evenly torque wheel nuts in the proper sequence to GM specifications. Brake linings should always be replaced as complete axle sets. See “Brake System Inspection” in Section 7 of this manual under Part C “Periodic Maintenance Inspections.” Brake Pedal Travel See your dealer if the brake pedal does not return to normal height, or if there is a rapid increase in pedal travel. This could be a sign of brake trouble. Brake Adjustment Every time you apply the brakes, with or without the vehicle moving, your brakes adjust for wear.


Replacing Brake System Parts The braking system on a vehicle is complex. Its many parts have to be of top quality and work well together if the vehicle is to have really good braking. Your vehicle was designed and tested with top-quality GM brake parts. When you replace parts of your braking system -- for example, when your brake linings wear down and you have to have new ones put in -- be sure you get new approved GM replacement parts. If you don’t, your brakes may no longer work properly. For example, if someone puts in brake linings that are wrong for your vehicle, the balance between your front and rear brakes can change -- for the worse. The braking performance you’ve come to expect can change in many other ways if someone puts in the wrong replacement brake parts.


6-32


Bulb Replacement For any bulb changing procedure not listed in this section, contact the service department of your Oldsmobile dealer. For the proper type of replacement bulb, see “Replacement Bulbs” in the Index. Halogen Bulbs


CAUTION:


Halogen bulbs have pressurized gas inside and can burst if you drop or scratch the bulb. You or others could be injured. Be sure to read and follow the instructions on the bulb package.


Battery Your new vehicle comes with a maintenance free ACDelcoR battery. When it’s time for a new battery, get one that has the replacement number shown on the original battery’s label. We recommend an ACDelco battery. Vehicle Storage If you’re not going to drive your vehicle for 25 days or more, remove the black, negative (-) cable from the battery. This will help keep your battery from running down.


CAUTION:


Batteries have acid that can burn you and gas that can explode. You can be badly hurt if you aren’t careful. See “Jump Starting” in the Index for tips on working around a battery without getting hurt.


Contact your dealer to learn how to prepare your vehicle for longer storage periods. Also, for your audio system, see “Theft-Deterrent Feature” in the Index.


6-33


Headlamps To replace your headlamps follow these steps: 1. Open the hood.


2. Pull straight up on the two headlamp retainers to


release the assembly locator tabs and take the retainers off. At the same time, hold the headlamp assembly in position by applying a little pressure against the headlamp lens. This prevents the lamp from falling out.


6-34


3. Slide the lamp assembly toward you.


4. Remove the rubber access cover from behind the


bulb you are replacing.


6. Replace the bulb, making sure you don’t touch the


bulb with your bare hands.


5. Twist and turn the bulb socket counterclockwise and


remove it from the lamp.


7. Reverse all steps and reinstall the headlamp


assembly, then check the lamps.


6-35


Headlamp Aiming


Your vehicle has a headlamp system equipped with horizontal and vertical aim indicators. The aim has been pre-set at the factory and should need no further adjustment. This is true even though your vertical and horizontal aim indicators may not fall exactly on the “0” (zero) marks on their scales. If your vehicle is damaged in an accident, the headlamp aim may be affected. Aim adjustment may be necessary if it is difficult to see lane markers (for horizontal aim), or if oncoming drivers flash their high beams at you (for vertical aim). If you believe your headlamps need to be re-aimed, we recommend that you take it to your dealer for service; however, it is possible for you to re-aim your headlamps as described in the following procedure.


6-36


NOTICE:


To make sure your headlamps are aimed properly, read all the instructions before beginning. Failure to follow these instructions could cause damage to headlamp parts.


To check the aim, the vehicle should be properly prepared as follows: D The vehicle must have all four tires on a perfectly


level surface.


D If necessary, pads may be used on an uneven surface. D The vehicle should not have any snow, ice or mud


attached to it.


D The vehicle should be fully assembled and all other work stopped while headlamp aiming is being done.


D There should not be any cargo or loading of the


vehicle, except it should have a full tank of fuel and one person or 160 lbs. (75 kg) on the driver’s seat.


D Close all doors. D Tires should be properly inflated. D Rock the vehicle to stabilize the suspension.


A. Horizontal Aim Adjustment Screw B. Vertical Aim Adjustment Screw Start with the horizontal aim. The adjustment screws can be turned with an E8 TorxR socket. Once the horizontal aim is adjusted, then adjust the vertical aim.


A. Horizontal Aim Adjustment Screw


(shown in previous photo)


B. Vertical Aim Adjustment Screw C. Horizontal Block Index Plate D. Vertical Aiming Level 1. Turn the horizontal aiming screw until the indicator


is lined up with zero.


2. Turn the vertical aiming screw until the level bubble


is lined up with zero.


6-37


Front Parking, Sidemarker and Turn Signal Cornering Lamp 1. Remove the headlamp assembly. Refer to the


removal procedure listed under “Headlamps” earlier in this section.


2. Remove the rubber bulb access cover. 3. Twist and pull each bulb socket from the


headlamp assembly.


4. Holding the base of the bulb, pull the bulb from


the socket.


5. Push the new bulb into the socket. 6. Put the bulb socket back into the headlamp assembly


and turn it clockwise until it is secure.


7. Reinstall the rubber access cover.


6-38


Fog Lamps


1. Remove the deflector located below the front fascia


by removing the two bolts.


2. Reach up from underneath the front of the vehicle and remove the electrical connector from the bulb assembly. 3. Turn the bulb socket a quarter turn counterclockwise


to remove.


4. Remove the bulb from the socket. 5. Place the new bulb into the socket. 6. Reverse the steps to reinstall.


Center High-Mounted Stoplamp (CHMSL) 1. Open the trunk.


2. Reach through the access opening in the trunk. 3. Remove the bulb by turning it one quarter


turn counterclockwise.


4. Place the new bulb into the socket. 5. Turn the bulb one quarter turn clockwise to reinstall. 6. Close the trunk.


6-39


Tail/Stop/Turn Signal lamp


4. Pull the taillamp housing away from the body


of the vehicle (3).


5. Squeeze the tab on the bulb socket and turn the


socket counterclockwise. 6. Pull out the bulb socket. 7. Pull the old bulb out of the socket.


(There are four bulbs on each taillamp.)


8. Push in a new bulb. 9. Reinstall the bulb socket into the housing and turn


it clockwise.


10. Reinstall the taillamp housing to the body


of the vehicle.


11. Reinstall the wing nuts. 12. Tighten the plastic nuts.


1. Unscrew the wing nut inside of the trunk (1) behind


the taillamp to be changed (if equipped with a convenience net, unhook the net).


2. Pull back the carpeting. 3. Remove the plastic wing nuts (2).


(Pliers may be required to remove the wing nuts.)


6-40


License Plate Lamp


1. Remove the four screws to remove the name plate. 2. Reach your hand up through underside of the trunk


into the slots.


3. Press the clip on one side of the bulb assembly


and pull out the assembly from the front with your other hand.


4. Remove the bulb from the socket. 5. Place the new bulb into the socket. 6. Reverse the steps to reinstall. When reinstalling bulb assembly, push in assembly until you hear a snap. Make sure the assembly is tight and not loose. Windshield Wiper Blade Replacement Windshield wiper blades should be inspected at least twice a year for wear or cracking. See “Wiper Blade Check” in Section 7 of this manual under Part B “Owner Checks and Services” for more information. Replacement blades come in different types and are removed in different ways. For the proper type and length, see “Normal Maintenance Replacement Parts” in the Index.


6-41


Here’s how to remove the wiper blades: 1. Pull the windshield wiper arm away from the windshield.


CAUTION:


Poorly maintained and improperly used tires are dangerous. D Overloading your tires can cause


overheating as a result of too much friction. You could have an air-out and a serious accident. See “Loading Your Vehicle” in the Index.


D Underinflated tires pose the same danger as


overloaded tires. The resulting accident could cause serious injury. Check all tires frequently to maintain the recommended pressure. Tire pressure should be checked when your tires are cold.


D Overinflated tires are more likely to be cut,


punctured or broken by a sudden impact -- such as when you hit a pothole. Keep tires at the recommended pressure.


D Worn, old tires can cause accidents. If your


tread is badly worn, or if your tires have been damaged, replace them.


2. Push the release lever and slide the wiper assembly


toward the driver’s side of the vehicle.


3. Install a new blade by reversing Steps 1 and 2. Tires Your new vehicle comes with high-quality tires made by a leading tire manufacturer. If you ever have questions about your tire warranty and where to obtain service, see your Oldsmobile Warranty booklet for details. 6-42


Inflation -- Tire Pressure The Tire-Loading Information label, which is located on the inside of the trunk lid, shows the correct inflation pressures for your tires when they’re cold. “Cold” means your vehicle has been sitting for at least three hours or driven no more than 1 mile (1.6 km).


NOTICE:


Don’t let anyone tell you that underinflation or overinflation is all right. It’s not. If your tires don’t have enough air (underinflation), you can get the following: D Too much flexing D Too much heat D Tire overloading D Bad wear D Bad handling D Bad fuel economy.


NOTICE: (Continued)


NOTICE: (Continued)


If your tires have too much air (overinflation), you can get the following: D Unusual wear D Bad handling D Rough ride D Needless damage from road hazards.


When to Check Check your tires once a month or more. Don’t forget your compact spare tire. It should be at 60 psi (420 kPa).


How to Check Use a good quality pocket-type gage to check tire pressure. You can’t tell if your tires are properly inflated simply by looking at them. Radial tires may look properly inflated even when they’re underinflated. Be sure to put the valve caps back on the valve stems. They help prevent leaks by keeping out dirt and moisture.


6-43


Tire Inspection and Rotation Tires should be rotated every 6,000 to 8,000 miles (10 000 to 13 000 km). Any time you notice unusual wear, rotate your tires as soon as possible and check wheel alignment. Also check for damaged tires or wheels. See “When It’s Time for New Tires” and “Wheel Replacement” later in this section for more information. The purpose of regular rotation is to achieve more uniform wear for all tires on the vehicle. The first rotation is the most important. See “Scheduled Maintenance Services” in the Index for scheduled rotation intervals.


When rotating your tires, always use the correct rotation pattern shown here. Don’t include the compact spare tire in your tire rotation. After the tires have been rotated, adjust the front and rear inflation pressures as shown on the Tire-Loading Information label. Make certain that all wheel nuts are properly tightened. See “Wheel Nut Torque” in the Index.


CAUTION:


Rust or dirt on a wheel, or on the parts to which it is fastened, can make wheel nuts become loose after a time. The wheel could come off and cause an accident. When you change a wheel, remove any rust or dirt from places where the wheel attaches to the vehicle. In an emergency, you can use a cloth or a paper towel to do this; but be sure to use a scraper or wire brush later, if you need to, to get all the rust or dirt off. (See “Changing a Flat Tire” in the Index.)


6-44


When It’s Time for New Tires


One way to tell when it’s time for new tires is to check the treadwear indicators, which will appear when your tires have only 1/16 inch (1.6 mm) or less of tread remaining.


You need a new tire if any of the following statements are true: D You can see the indicators at three or more places


around the tire.


D You can see cord or fabric showing through the


tire’s rubber.


D The tread or sidewall is cracked, cut or snagged deep


enough to show cord or fabric.


D The tire has a bump, bulge or split. D The tire has a puncture, cut or other damage that


can’t be repaired well because of the size or location of the damage.


Buying New Tires To find out what kind and size of tires you need, look at the Tire-Loading Information label. The tires installed on your vehicle when it was new had a Tire Performance Criteria Specification (TPC Spec) number on each tire’s sidewall. When you get new tires, get ones with that same TPC Spec number. That way your vehicle will continue to have tires that are designed to give proper endurance, handling, speed rating, traction, ride and other things during normal service on your vehicle. If your tires have an all-season tread design, the TPC number will be followed by an “MS” (for mud and snow).


6-45


If you ever replace your tires with those not having a TPC Spec number, make sure they are the same size, load range, speed rating and construction type (bias, bias-belted or radial) as your original tires.


CAUTION:


Mixing tires could cause you to lose control while driving. If you mix tires of different sizes or types (radial and bias-belted tires), the vehicle may not handle properly, and you could have a crash. Using tires of different sizes may also cause damage to your vehicle. Be sure to use the same size and type tires on all wheels. It’s all right to drive with your compact spare, though. It was developed for use on your vehicle.


CAUTION:


If you use bias-ply tires on your vehicle, the wheel rim flanges could develop cracks after many miles of driving. A tire and/or wheel could fail suddenly, causing a crash. Use only radial-ply tires with the wheels on your vehicle.


Uniform Tire Quality Grading The following information relates to the system developed by the United States National Highway Traffic Safety Administration, which grades tires by treadwear, traction and temperature performance. (This applies only to vehicles sold in the United States.) The grades are molded on the sidewalls of most passenger car tires. The Uniform Tire Quality Grading system does not apply to deep tread, winter-type snow tires, space-saver or temporary use spare tires, tires with nominal rim diameters of 10 to 12 inches (25 to 30 cm), or to some limited-production tires.


6-46


While the tires available on General Motors passenger cars and light trucks may vary with respect to these grades, they must also conform to Federal safety requirements and additional General Motors Tire Performance Criteria (TPC) standards.


Treadwear The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire graded 150 would wear one and a half (1 1/2) times as well on the government course as a tire graded 100. The relative performance of tires depends upon the actual conditions of their use, however, and may depart significantly from the norm due to variations in driving habits, service practices and differences in road characteristics and climate. Traction -- AA, A, B, C The traction grades, from highest to lowest, are AA, A, B, and C. Those grades represent the tire’s ability to stop on wet pavement as measured under controlled conditions on specified government test surfaces of asphalt and concrete. A tire marked C may have poor traction performance.


Warning: The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning, or peak traction characteristics. Temperature -- A, B, C The temperature grades are A (the highest), B, and C, representing the tire’s resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel. Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure. The grade C corresponds to a level of performance which all passenger car tires must meet under the Federal Motor Vehicle Safety Standard No. 109. Grades B and A represent higher levels of performance on the laboratory test wheel than the minimum required by law. Warning: The temperature grade for this tire is established for a tire that is properly inflated and not overloaded. Excessive speed, underinflation, or excessive loading, either separately or in combination, can cause heat buildup and possible tire failure.


6-47


Wheel Alignment and Tire Balance The wheels on your vehicle were aligned and balanced carefully at the factory to give you the longest tire life and best overall performance. Scheduled wheel alignment and wheel balancing are not needed. However, if you notice unusual tire wear or your vehicle pulling one way or the other, the alignment may need to be reset. If you notice your vehicle vibrating when driving on a smooth road, your wheels may need to be rebalanced. Wheel Replacement Replace any wheel that is bent, cracked, or badly rusted or corroded. If wheel nuts keep coming loose, the wheel, wheel bolts and wheel nuts should be replaced. If the wheel leaks air, replace it (except some aluminum wheels, which can sometimes be repaired). See your dealer if any of these conditions exist. Your dealer will know the kind of wheel you need. Each new wheel should have the same load-carrying capacity, diameter, width, offset and be mounted the same way as the one it replaces. If you need to replace any of your wheels, wheel bolts or wheel nuts, replace them only with new GM original equipment parts. This way, you will be sure to have the right wheel, wheel bolts and wheel nuts for your vehicle. 6-48


CAUTION:


Using the wrong replacement wheels, wheel bolts or wheel nuts on your vehicle can be dangerous. It could affect the braking and handling of your vehicle, make your tires lose air and make you lose control. You could have a collision in which you or others could be injured. Always use the correct wheel, wheel bolts and wheel nuts for replacement.


NOTICE:


The wrong wheel can also cause problems with bearing life, brake cooling, speedometer or odometer calibration, headlamp aim, bumper height, vehicle ground clearance and tire or tire chain tire clearance to the body and chassis.


See “Changing a Flat Tire” in the Index for more information.


Used Replacement Wheels


CAUTION:


Putting a used wheel on your vehicle is dangerous. You can’t know how it’s been used or how far it’s been driven. It could fail suddenly and cause an accident. If you have to replace a wheel, use a new GM original equipment wheel.


Tire Chains


NOTICE:


Use tire chains only where legal and only when you must. Use only SAE Class “S” type chains that are the proper size for your tires. Install them on the front tires and tighten them as


NOTICE: (Continued)


NOTICE: (Continued)


tightly as possible with the ends securely fastened. Drive slowly and follow the chain manufacturer’s instructions. If you can hear the chains contacting your vehicle, stop and retighten them. If the contact continues, slow down until it stops. Driving too fast or spinning the wheels with chains on will damage your vehicle.


Appearance Care Remember, cleaning products can be hazardous. Some are toxic. Others can burst into flame if you strike a match or get them on a hot part of the vehicle. Some are dangerous if you breathe their fumes in a closed space. When you use anything from a container to clean your vehicle, be sure to follow the manufacturer’s warnings and instructions. And always open your doors or windows when you’re cleaning the inside.


6-49


Never use these to clean your vehicle: D Gasoline D Benzene D Naphtha D Carbon Tetrachloride D Acetone D Paint Thinner D Turpentine D Lacquer Thinner D Nail Polish Remover They can all be hazardous -- some more than others -- and they can all damage your vehicle, too. Don’t use any of these unless this manual says you can. In many uses, these will damage your vehicle: D Alcohol D Laundry Soap D Bleach D Reducing Agents


Cleaning the Inside of Your Vehicle Use a vacuum cleaner often to get rid of dust and loose dirt. Wipe vinyl, leather, plastic and painted surfaces with a clean, damp cloth. Cleaning of Fabric/Carpet Your dealer has two cleaners, Multi-Purpose Interior Cleaner and Capture Non-Solvent Dry Spot and Soil Remover for cleaning fabric and carpet. They will clean normal spots and stains very well. You can get GM-approved cleaning products from your dealer. (See “Appearance Care and Materials” in the Index.) Here are some cleaning tips: D Always read the instructions on the cleaner label. D Clean up stains as soon as you can -- before they set. D Carefully scrape off any excess stain. D Use a clean cloth or sponge, and change to a clean


area often. A soft brush may be used if stains are stubborn.


D If a ring forms on fabric after spot cleaning, clean the


entire area immediately or it will set.


6-50


Using Multi-Purpose Interior Cleaner on Fabric 1. Vacuum and brush the area to remove any loose dirt. 2. Always clean a whole trim panel or section.


Mask surrounding trim along stitch or welt lines. 3. Mix powdered cleaner following the directions on


the container label to form thick suds.

Loading...
x