2007 Nissan Xterra Owners Manual

system is not operating properly. The TPMS mal- function indicator is combined with the low tire pressure telltale. When the system detects a malfunction, the telltale will flash for approxi- mately one minute and then remain continuously illuminated. This sequence will continue upon subsequent vehicle start-ups as long as the mal- function exists. When the malfunction indicator is illuminated, the system may not be able to detect or signal low tire pressure as intended. TPMS malfunctions may occur for a variety of reasons, including the installation of replacement or alter- nate tires or wheels on the vehicle that prevent the TPMS from functioning properly. Always check the TPMS malfunction telltale after replac- ing one or more tires or wheels on your vehicle to ensure that the replacement or alternate tires and wheels allow the TPMS to continue to function properly. Additional information: c The TPMS does not monitor the tire pres-

sure of the spare tire.

c The TPMS will activate only when the vehicle is driven at speeds above 16 MPH (25
km/h). Also, this system may not detect a sudden drop in tire pressure (for example a flat tire while driving).

Starting and driving 5-3

Z REVIEW COPY—2007 Xterra (xtr) Owners Manual—USA_English (nna) 02/27/07—debbie X

c The low tire pressure warning light does not automatically turn off when the tire pressure is adjusted. After the tire is inflated to the recommended pressure, the vehicle must be driven at speeds above 16 MPH (25 km/h) to activate the TPMS and turn off the low tire pressure warning light. Use a tire pressure gauge to check the tire pressure.

c Tire pressure rises and falls depending on the heat caused by the vehicle(cid:146)s operation and the outside temperature. Low outside temperature can lower the temperature of the air inside the tire which can cause a lower tire inflation pressure. This may cause the low tire pressure warning light to illumi- nate. If the warning light illuminates in low ambient temperature, check the tire pres- sure for all four tires.

c You can also check the pressure of all tires (except the spare tire) on the display screen. The order of the tire pressure figures dis- played on the screen does not correspond with the actual order of the tire position. See (cid:147)Tire pressure information(cid:148) in the (cid:147)Display screen, heater, air conditioner and audio systems(cid:148) section.

For additional information, see (cid:147)Low tire pressure warning light(cid:148) in the (cid:147)Instruments and controls(cid:148) section, (cid:147)Tire Pressure Monitoring System (TPMS)(cid:148) in the (cid:147)In case of emergency(cid:148) section.

WARNING

c If the low tire pressure warning light illuminates while driving, avoid sudden steering maneuvers or abrupt braking, reduce vehicle speed, pull off the road to a safe location and stop the vehicle as soon as possible. Serious vehicle damage could occur and may lead to an accident and could result in serious personal injury. Check the tire pressure for all four tires. Adjust the tire pressure to the recommended COLD tire pres- sure shown on the Tire and Loading Information label to turn the low tire pressure warning light OFF. If you have a flat tire, replace it with a spare tire as soon as possible. (See (cid:147)Flat tire(cid:148) in the (cid:147)In case of emergency(cid:148) section for changing a flat tire.)

c When a spare tire is mounted or a wheel is replaced, tire pressure will not be indicated, the TPMS will not function and the low tire pressure warning light will flash for approximately 1 minute. The light will remain on after 1 minute. Contact your NISSAN dealer as soon as possible for tire replacement and/or system resetting.

c Replacing tires with those not originally specified by NISSAN could affect the proper operation of the TPMS.

c Do not inject any tire liquid or aerosol tire sealant into the tires, as this may cause a malfunction of the tire pressure sensors.

CAUTION

Do not place metalized film or any metal parts (antenna, etc.) on the windows. This may cause poor reception of the signals from the tire pressure sensors, and the TPMS will not function properly.

Some devices and transmitters may temporarily interfere with the operation of the TPMS and cause the low tire pressure warning light to illu- minate.

5-4 Starting and driving

Z REVIEW COPY—2007 Xterra (xtr) Owners Manual—USA_English (nna) 02/27/07—debbie X

Some examples are: (cid:150) Facilities or electric devices using similar radio

frequencies are near the vehicle.

(cid:150) If a transmitter set to similar frequencies is

being used in or near the vehicle.

(cid:150) If a computer (or similar equipment) or a DC/AC converter is being used in or near the vehicle.

FCC Notice: Changes or modifications not expressly ap- proved by the party responsible for compli- ance could void the user(cid:146)s authority to op- erate the equipment. This device complies with Part 15 of the FCC Rules and RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, in- cluding interference that may cause undes- ired operation of the device.

ON-PAVEMENT AND OFF-ROAD DRIVING PRECAUTIONS Utility vehicles have a significantly higher rollover rate than other types of vehicles. They have higher ground clearance than passen- ger cars to make them capable of performing in a variety of on-pavement and off-road applications. This gives them a higher center of gravity than ordinary cars. An advantage of higher ground clearance is a better view of the road, allowing you to anticipate problems. However, they are not designed for cornering at the same speeds as conventional two-wheel drive vehicles any more than low-slung sports cars are designed to per- form satisfactorily under off-road conditions. If at all possible, avoid sharp turns at high speeds. As with other vehicles of this type, failure to operate this vehicle correctly may result in loss of control or vehicle rollover. In a rollover crash, an unbelted person is significantly more likely to die than a person wearing a seat belt. Be sure to read the driving safety precautions later in this section.

AVOIDING COLLISION AND ROLLOVER

WARNING

Failure to operate this vehicle in a safe and prudent manner may result in loss of control or an accident.

Be alert and drive defensively at all times. Obey all traffic regulations. Avoid excessive speed, high speed cornering, or sudden steering ma- neuvers, because these driving practices could cause you to lose control of your vehicle. As with any vehicle, loss of control could result in a collision with other vehicles or objects, or cause the vehicle to roll over, particularly if the loss of control causes the vehicle to slide sideways. Be attentive at all times, and avoid driving when tired. Never drive when under the influence of alcohol or drugs (including pre- scription or over-the-counter drugs which may cause drowsiness). Always wear your seat belt as outlined in the (cid:147)Safety (cid:150) Seats, seat belts and supplemental restraint system(cid:148) section of this manual, and also instruct your passengers to do so.

Seat belts help reduce the risk of injury in colli- sions and rollovers. In a rollover crash, an unbelted or improperly belted person is Starting and driving 5-5

Z REVIEW COPY—2007 Xterra (xtr) Owners Manual—USA_English (nna) 02/27/07—debbie X

significantly more likely to be injured or killed than a person properly wearing a seat belt. DRINKING ALCOHOL/DRUGS AND DRIVING

WARNING

Never drive under the influence of alcohol or drugs. Alcohol in the bloodstream re- duces coordination, delays reaction time and impairs judgement. Driving after drinking alcohol increases the likelihood of being involved in an accident injuring yourself and others. Additionally, if you are injured in an accident, alcohol can increase the severity of the injury.

NISSAN is committed to safe driving. However, you must choose not to drive under the influence of alcohol. Every year thousands of people are injured or killed in alcohol-related accidents. Al- though the local laws vary on what is considered to be legally intoxicated, the fact is that alcohol affects all people differently and most people underestimate the effects of alcohol.

Remember, drinking and driving don(cid:146)t mix! And that is true for drugs, too (over-the-counter, pre- scription, and illegal drugs). Don(cid:146)t drive if your

5-6 Starting and driving

ability to operate your vehicle is impaired by alco- hol, drugs, or some other physical condition. DRIVING SAFETY PRECAUTIONS Your NISSAN is designed for both normal and off-road use. However, avoid driving in deep wa- ter or mud as your NISSAN is mainly designed for leisure use, unlike a conventional off-road ve- hicle.

Remember that two-wheel drive models are less capable than four-wheel drive models for rough road driving and extrication when stuck in deep snow or mud, or the like.

Please observe the following precautions:

WARNING

c Drive carefully when off the road and avoid dangerous areas. Every person who drives or rides in this vehicle should be seated with their seat belt fastened. This will keep you and your passengers in position when driving over rough terrain.

c Do not drive across steep slopes. In- stead drive either straight up or straight down the slopes. Off-road vehicles can tip over sideways much more easily than they can forward or backward.

c Many hills are too steep for any vehicle. If you drive up them, you may stall. If you drive down them, you may not be able to control your speed. If you drive across them, you may roll over.

c Do not shift gears while driving on downhill grades as this could cause loss of control of the vehicle.

c Stay alert when driving to the top of a hill. At the top there could be a drop-off or other hazard that could cause an accident.

c If your engine stalls or you cannot make it to the top of a steep hill, never at- tempt to turn around. Your vehicle could tip or roll over. Always back straight down in R (Reverse) gear. Never back down in N (Neutral) or with the clutch depressed (manual transmission vehicles), using only the brake, as this could cause loss of control.

c Heavy braking going down a hill could cause your brakes to overheat and fade, resulting in loss of control and an acci- dent. Apply brakes lightly and use a low gear to control your speed. Use the Hill Descent so equipped).

Control

feature

(if

Z REVIEW COPY—2007 Xterra (xtr) Owners Manual—USA_English (nna) 02/27/07—debbie X

c Lower your speed when encountering strong crosswinds. With a higher center of gravity, your NISSAN is more af- fected by strong side winds. Slower speeds ensure better vehicle control.

c Do not drive beyond the performance capability of the tires, even with 4WD engaged.

to raise two wheels off

c For 4WD equipped vehicles, do not at- tempt the ground and shift the transmission to any drive or reverse position with the engine running. Doing so may result in drivetrain damage or unexpected ve- hicle movement which could result in serious vehicle damage or personal injury.

c Unsecured cargo can be thrown around when driving over rough terrain. Prop- erly secure all cargo so it will not be thrown forward and cause injury to you or your passengers.

c To avoid raising the center of gravity excessively, do not exceed the rated capacity of the roof rack/gear bin (if so equipped) and evenly distribute the load. Secure heavy loads in the cargo area as far forward and as low as pos- sible. Do not equip the vehicle with tires larger than specified in this manual. This could cause your vehicle to roll over.

c Do not grip the inside or spokes of the steering wheel when driving off-road. The steering wheel could move sud- denly and injure your hands. Instead drive with your fingers and thumbs on the outside of the rim.

c Before operating the vehicle, ensure that the driver and all passengers have their seat belts fastened.

c Always drive with the floor mats in

place as the floor may become hot.

c Do not attempt to test a 4WD equipped vehicle on a 2-wheel dynamometer (such as the dynamometers used by some states for emissions testing), or similar equipment even if the other two wheels are raised off the ground. Make sure you inform test facility personnel that your vehicle is equipped with 4WD before it is placed on a dynamometer. Using the wrong test equipment may result in drivetrain damage or unex- pected vehicle movement which could result in serious vehicle damage or per- sonal injury.

c Accelerating quickly, sharp steering maneuvers or sudden braking may cause loss of control.

c If at all possible, avoid sharp turning maneuvers, particularly at high speeds. Your NISSAN four-wheel drive vehicle has a higher center of gravity than a two-wheel drive vehicle. The vehicle is not designed for cornering at the same speeds as conventional two-wheel drive vehicles. Failure to operate this vehicle correctly could result in loss of control and/or a rollover accident.

Starting and driving 5-7

Z REVIEW COPY—2007 Xterra (xtr) Owners Manual—USA_English (nna) 02/27/07—debbie X

c Always use tires of the same type, size, brand, construction (bias, bias-belted, or radial), and tread pattern on all four wheels. Install tire chains on the rear wheels when driving on slippery roads and drive carefully.

c Be sure to check the brakes immedi- ately after driving in mud or water. See (cid:147)Brake system(cid:148) later in this section for (cid:147)Wet brakes(cid:148).

c Avoid parking your vehicle on steep hills. If you get out of the vehicle and it rolls forward, backward or sideways, you could be injured.

c Whenever you drive off-road through sand, mud or water as deep as the wheel hub, more frequent maintenance may be required. See (cid:147)Periodic mainte- nance(cid:148) in the (cid:147)NISSAN Service and Maintenance Guide.(cid:148)

5-8 Starting and driving

IGNITION SWITCH

WARNING

Never remove or turn the key to the LOCK position while driving. The steering wheel will lock. This may cause the driver to lose control of the vehicle and could result in serious vehicle damage or personal injury.

WSD0041

AUTOMATIC TRANSMISSION The ignition lock is designed so the key cannot be turned to the LOCK position and removed until the shift selector lever is moved to the P (Park) position. When removing the key from the ignition, make sure the shift selector lever is in the P (Park) position. If the selector lever is not returned to P (Park) position, the key cannot be moved to the LOCK position.

Z REVIEW COPY—2007 Xterra (xtr) Owners Manual—USA_English (nna) 02/27/07—debbie X

To remove the key from the ignition switch: 1. Shift the selector lever to the P (Park) posi-

tion with the key in the ON position. 2. Turn the key to the LOCK position. 3. Remove the key from the ignition. If the selector lever is shifted to the P (Park) position after the key is turned to the OFF posi- tion or when the key cannot be turned to the LOCK position, proceed as follows to remove the key. 1. Move the shift selector lever into the P (Park)

position.

2. Turn the ignition key slightly toward the ON

position.

3. Turn the key to the LOCK position. 4. Remove the key. The shift selector lever is designed so it cannot moved out of P (Park) and into any of the other gear positions if the ignition key is turned to OFF position or if the key is removed from the switch. The shift selector lever can be moved if the ignition switch is in the ON position and the foot brake pedal is depressed.

There is an OFF position between the LOCK and ACC positions. The OFF position is indicated by a (cid:147)1(cid:148) on the key cylinder. When the ignition is in the OFF position, the steering wheel is not locked. In order for the steering wheel to be locked, it must be turned about 1/8 of a turn clockwise from the straight up position. To lock the steering wheel, turn the key to the LOCK position. Remove the key. To unlock the steering wheel, insert the key and turn it gently while rotating the steer- ing wheel slightly right and left. If the key will not turn from the LOCK posi- tion, turn the steering wheel to the left or right while turning the key to unlock the key cylinder.

WSD0052

MANUAL TRANSMISSION The ignition switch includes a device that helps prevent accidental removal of the key while driv- ing.

The key can only be removed when the ignition switch is in the LOCK position.

On manual transmission models, to turn the igni- tion key to LOCK position from ACC or ON position, turn the key to OFF, push the key in, then turn the key to LOCK.

In order for the steering wheel to be locked, it must be turned about 1/8 of a turn clockwise from the straight up position.

Starting and driving 5-9

Z REVIEW COPY—2007 Xterra (xtr) Owners Manual—USA_English (nna) 02/27/07—debbie X

If the engine fails to start using a registered key (for example, when interference is caused by another registered key, an automated toll road device or automatic payment device on the key ring), restart the engine using the following pro- cedures: 1. Leave the ignition switch in the ON position

for approximately 5 seconds.

2. Turn the ignition switch to the OFF or LOCK position, and wait approximately 10 sec- onds.

3. Repeat steps 1 and 2. 4. Restart the engine while holding the device (which may have caused the interference) separate from the registered key.

If the no start condition re-occurs, NISSAN rec- ommends placing the registered key on a sepa- rate key ring to avoid interference from other devices.

BEFORE STARTING THE ENGINE

c Make sure the area around the vehicle is

clear.

c Check fluid levels such as engine oil, cool- ant, brake fluid, and window washer fluid as frequently as possible, or at least whenever you refuel.

c Check that all windows and lights are clean. c Visually inspect tires for their appearance and condition. Also check tires for proper inflation.

c Lock all doors. c Position seat and adjust head restraints. c Adjust inside and outside mirrors. c Fasten seat belts and ask all passengers to

do likewise.

c Check the operation of warning lights when the key is turned to the ON (3) position. See (cid:147)Warning/indicator lights and audible re- minders(cid:148) in the (cid:147)Instruments and controls(cid:148) section of this manual.

To lock the steering wheel, turn the key to the LOCK position. Remove the key. To unlock the steering wheel, insert the key and turn it gently while rotating the steer- ing wheel slightly right and left. KEY POSITIONS LOCK: Normal parking position (0)

OFF: (Not used) (1)

ACC: (Accessories) (2)

This position activates electrical accessories such as the radio when the engine is not running.

ON: Normal operating position (3)

This position turns on the ignition system and the electrical accessories.

START: (4)

This position starts the engine. As soon as the engine has started, release the key. It automati- cally returns to the ON position. NISSAN VEHICLE IMMOBILIZER SYSTEM (if so equipped) The NISSAN Vehicle Immobilizer System will not allow the engine to start without the use of the registered key.

5-10 Starting and driving

Z REVIEW COPY—2007 Xterra (xtr) Owners Manual—USA_English (nna) 02/27/07—debbie X

4. Allow the engine to idle for at least 30 sec- onds after starting. Do not race the engine while warming it up. Drive at moderate speed for a short distance first, especially in cold weather.

STARTING THE ENGINE

1. Apply the parking brake. 2. Automatic transmission:

Move the shift selector lever to P (Park) or N (Neutral). P (Park) is recommended. The shift selector lever cannot be moved out of P (Park) and into any of the other gear positions if the ignition key is turned to the OFF position or if the key is removed from the ignition switch.

The starter is designed not to operate if the shift selector lever is in any of the driving positions.

Manual transmission:

Move the shift lever to N (Neutral). Depress the clutch pedal to the floor while cranking the engine. The starter is designed not to operate unless the clutch pedal is fully de- pressed.

3. Crank the engine with your foot off the accelerator pedal by turning the ignition key to START. Release the key when the engine starts. If the engine starts, but fails to run, repeat the above procedure.

c If the engine is very hard to start in ex- tremely cold weather or when restarting, depress the accelerator pedal a little (ap- proximately 1/3 to the floor) and hold it and then crank the engine. Release the key and the accelerator pedal when the engine starts.

c If the engine is very hard to start because it is flooded, depress the accelerator pedal all the way to the floor and hold it. Crank the engine for 5-6 seconds. After cranking the engine, release the accel- erator pedal. Crank the engine with your foot off the accelerator pedal by turn- ing the ignition key to START. Release the key when the engine starts. If the engine starts, but fails to run, repeat the above procedure.

CAUTION

Do not operate the starter for more than 15 seconds at a time. If the engine does not start, turn the key off and wait 10
seconds before cranking again, otherwise the starter could be damaged.

Starting and driving 5-11

Z REVIEW COPY—2007 Xterra (xtr) Owners Manual—USA_English (nna) 02/27/07—debbie X

DRIVING THE VEHICLE

AUTOMATIC TRANSMISSION

WARNING

c Do not depress the accelerator pedal while shifting from P (Park) or N (Neu- tral) to R (Reverse), D (Drive), 3, 2 or 1. Always depress the brake pedal until shifting is completed. Failure to do so could cause you to lose control and have an accident.

c Cold engine idle speed is high, so use caution when shifting into a forward or reverse gear before the engine has warmed up.

c Never shift to P (Park) or R (Reverse) while the vehicle is moving. This could cause an accident.

CAUTION

c When stopping the vehicle on an uphill grade, do not hold the vehicle by de- pressing the accelerator pedal. The foot brake should be used for this purpose. c Do not downshift abruptly on slippery roads. This may cause a loss of control.

The automatic transmission in your vehicle is electronically controlled to produce maximum power and smooth operation. 5-12 Starting and driving

The recommended operating procedures for this transmission are shown on the following pages. Follow these procedures for maximum vehicle performance and driving enjoyment. Starting the vehicle 1. After starting the engine, fully depress the foot brake pedal before moving the shift selector lever out of the P (Park) position.

2. Keep the foot brake pedal depressed and move the shift selector lever into a driving gear.

3. Release the foot brake, then gradually start

the vehicle in motion.

The automatic transmission is designed so the foot brake pedal MUST be depressed before shifting from P (Park) to any drive position while the ignition switch is in the ON position. The shift selector lever cannot be moved out of P (Park) and into any of the other gear positions if the ignition key is turned to the LOCK, OFF or ACC position or if the key is removed.

LSD0151

To move the selector lever:

: Push the button while depressing the

brake pedal

: Push the button to shift

: Shift without depressing brake pedal

Shifting After starting the engine, fully depress the brake pedal and move the shift selector lever out of the P (Park) position.

Z REVIEW COPY—2007 Xterra (xtr) Owners Manual—USA_English (nna) 02/27/07—debbie X

WARNING

R (Reverse):

Apply the parking brake if the selector lever is in any position while the engine is not running. Failure to do so could cause the vehicle to move unexpectedly or roll away and result in serious personal injury or property damage.

If the key is turned to the OFF or ACC position for any reason while the vehicle is in N (Neutral), or any D (Drive) position, the key cannot be turned to the LOCK position and be removed from the ignition switch. Move the selector lever to the P (Park) position, then the key can be turned to LOCK. P (Park):

Use this selector position when the vehicle is parked or when starting the engine. Make sure the vehicle is completely stopped. The brake pedal should be depressed to move the selector lever from N (Neutral) or any drive position to P (Park). Apply the parking brake. When parking on a hill, apply the parking brake first, then shift the selector lever into the P (Park) position.

CAUTION

Use this position only when the vehicle is completely stopped.

Use this position to back up. Make sure the vehicle is completely stopped before selecting the R (Reverse) position. The brake pedal must be depressed to move the selector lever from P (Park), N (Neutral) or any drive position to R (Reverse). N (Neutral): Neither forward nor reverse gear is engaged. The engine can be started in this position. You may shift to N (Neutral) and restart a stalled engine while the vehicle is moving. D (Drive): Use this position for all normal forward driving. 3 (Third gear): Use this position for driving up and down long slopes where engine braking would be advanta- geous. Do not downshift into the 3 position at speeds over the following and do not exceed the follow- ing speeds in the 3 position.

2WD: 62 MPH (100 km/h) 4H: 62 MPH (100 km/h) 4LO: 31 MPH (50 km/h)

2 (Second gear): Use this position for hill climbing or engine brak- ing on downhill grades. Do not downshift into the 2 position at speeds over the following and do not exceed the follow- ing speeds in the 2 position.

2WD: 71 MPH (115 km/h) 4H: 62 MPH (100 km/h) 4LO: 31 MPH (50 km/h)

1 (Low gear): Use this position when climbing steep hills slowly or slow driving through deep snow, sand or mud, or for maximum engine braking on steep downhill grades.

Starting and driving 5-13

Z REVIEW COPY—2007 Xterra (xtr) Owners Manual—USA_English (nna) 02/27/07—debbie X

Do not downshift into the 1 position at speeds over the following and do not exceed the follow- ing speeds in the 1 position.

2WD: 43 MPH (70 km/h) 4H: 43 MPH (70 km/h) 4LO: 31 MPH (50 km/h)

5-14 Starting and driving

To push the shift lock release, complete the fol- lowing procedure:

1. Turn the ignition key to the LOCK position

and remove the key

2. Apply the parking brake.

3. Remove the shift

lock release cover as

shown.

4.

Insert a small screwdriver in the shift lock release slot and push down.

5. Move the shift selector lever to the N (Neu- tral) position while holding down the shift lock release.

6. Turn the key to the ON position to unlock the steering wheel. Now the vehicle may be moved to the desired location.

If the shift selector lever cannot be moved out of P (Park), have a NISSAN dealer check the auto- matic transmission system as soon as possible.

WARNING

If the selector lever cannot be moved from the P (Park) position while the engine is running and the brake pedal is depressed, the stop lights may not work. Malfunction- ing stop lights could cause an accident injuring yourself and others.

LSD0141

Shift lock release If the battery is discharged, the shift selector lever may not be moved from the P (Park) position even with the brake pedal depressed. To move the shift selector lever, release the shift lock. The shift selector lever can be moved to N (Neutral). However, the steering wheel will be locked unless the ignition switch is turned to the ON position. This allows the vehicle to be moved if the battery is discharged.

Z REVIEW COPY—2007 Xterra (xtr) Owners Manual—USA_English (nna) 02/27/07—debbie X

Accelerator downshift (cid:151) in D position (cid:151) For passing or hill climbing, depress the accel- erator pedal to the floor. This shifts the transmis- sion down into a lower gear, depending on the vehicle speed.

OFF:

For driving up and down long slopes where engine braking is nec- essary push the Overdrive switch once. The O/D OFF indicator light in the instrument panel comes on at this time.

When cruising at a low speed or climbing a gentle slope, you may feel uncomfortable shift shocks as the transmission shifts into and out of Overdrive repeatedly. In this case, depress the Overdrive switch to turn the Overdrive off. The O/D OFF indicator light in the instrument panel comes on at this time. When driving conditions change, depress the Overdrive switch to turn the Overdrive on. Remember not to drive at high speeds for ex- tended periods of time with the Overdrive off. This reduces fuel economy.

LSD0142

Overdrive switch Each time your vehicle is started, the transmis- sion is automatically (cid:147)reset(cid:148) to overdrive ON. ON: With the engine running and the

shift selector lever in the D (Drive) position, the transmission upshifts into Overdrive as vehicle speed increases.

Overdrive does not engage until the engine has reached operating temperature.

Starting and driving 5-15

Z REVIEW COPY—2007 Xterra (xtr) Owners Manual—USA_English (nna) 02/27/07—debbie X

MANUAL TRANSMISSION (if so equipped)

WARNING

c Do not downshift abruptly on slippery roads. This may cause a loss of control. c Do not over-rev the engine when shift- ing to a lower gear. This may cause a loss of control or engine damage.

CAUTION

c Do not rest your foot on the clutch pedal while driving. This may cause clutch damage.

c Fully depress the clutch pedal before shifting to help prevent transmission damage.

c Stop your vehicle completely before

shifting into R (Reverse).

c When the vehicle is stopped with the engine running (for example, at a stop light), shift to N (Neutral) and release the clutch pedal with the foot brake applied.

5-16 Starting and driving

To back up depress the shift lever and then move it to the R (Reverse) position after stopping the vehicle completely. If it is difficult to move the shift lever into R (Reverse) or 1 (First), shift into N (Neutral), then release the clutch pedal. Fully depress the clutch pedal again and shift into R (Reverse) or 1 (First). If your vehicle is equipped with 4-wheel drive, see (cid:147)Transfer case shifting procedures(cid:148) later in this section. Suggested upshift speeds The following are suggested vehicle speeds for shifting into a higher gear. These suggestions relate to fuel economy and vehicle performance. Actual upshift speeds will vary according to road conditions, the weather and individual driving habits. c Two-wheel drive models and four-wheel

drive models (2H and 4H position):

GEAR CHANGE

MPH (km/h)

1st to 2nd 2nd to 3rd 3rd to 4th 4th to 5th 5th to 6th

11 (18) 17 (27) 25 (40) 32 (51) 45 (72)

LSD0148

Shifting To change gears, or when upshifting or down- shifting, depress the clutch pedal fully, shift into the appropriate gear, then release the clutch slowly and smoothly.

To ensure smooth gear changes, fully depress the clutch pedal before operating the shift lever. If the clutch pedal is not fully depressed before the transmission is shifted, a gear noise may be heard. Transmission damage could occur.

Start the vehicle in 1st gear and shift to 2nd, 3rd, 4th, 5th and 6th gear in sequence according to vehicle speed.

Z REVIEW COPY—2007 Xterra (xtr) Owners Manual—USA_English (nna) 02/27/07—debbie X

PARKING BRAKE

WARNING

c Be sure the parking brake is fully re- leased before driving. Failure to do so can cause brake failure and lead to an accident.

c Do not release the parking brake from

outside the vehicle.

c Do not use the gear shift in place of the parking brake. When parking, be sure the parking brake is fully engaged.

c Do not leave children unattended in a vehicle. They could release the parking brake and cause an accident.

c 4(cid:150)wheel drive model (4L position):

GEAR CHANGE

MPH (km/h)

1st to 2nd 2nd to 3rd 3rd to 4th 4th to 5th 5th to 6th

(cid:151) (cid:151) (cid:151) (cid:151) (cid:151)

Suggested maximum speed in each gear Downshift to a lower gear if the engine is not running smoothly, or if you need to accelerate.

Do not exceed the maximum suggested speed (shown below) in any gear. For level road driving, use the highest gear suggested for that speed. Always observe posted speed limits, and drive according to the road conditions, which will en- sure safe operation. Do not over-rev the engine when shifting to a lower gear as it may cause engine damage or loss of vehicle control.

Allowable maximum speed in each gear: 2(cid:150)wheel drive models

GEAR

1st 2nd

MPH (km/h)

35 (56) 60 (97)

GEAR

3rd 4th 5th 6th

4(cid:150)wheel drive models 2H/4H position

GEAR

1st 2nd 3rd 4th 5th 6th

MPH (km/h)

87 (141)

(cid:151) (cid:151) (cid:151)

MPH (km/h)

34 (55) 60 (97) 87 (141)

(cid:151) (cid:151) (cid:151)

4L position

GEAR

MPH (km/h)

1st 2nd 3rd 4th 5th 6th

13 (21) 23 (37) 33 (54) 45 (73) 57 (93)

(cid:151)

Starting and driving 5-17

Z REVIEW COPY—2007 Xterra (xtr) Owners Manual—USA_English (nna) 02/27/07—debbie X

CRUISE CONTROL (if so equipped)

3. While pulling up on the parking brake lever slightly, push the button and lower com- pletely sB .

4. Before driving, be sure the brake warning

light goes out.

LSD0150

To engage: Pull the lever up sA . To release: 1. Firmly apply the foot brake. 2. Manual transmission models:

Place the shift lever in the N (Neutral) posi- tion. Automatic transmission models: Move the shift selector lever to the P (Park) position.

5-18 Starting and driving

WSD0153

ACCEL/RES switch 1. 2. COAST/SET switch 3. ON/OFF switch 4. CANCEL switch PRECAUTIONS ON CRUISE CONTROL c If the cruise control system malfunctions, it cancels automatically. The SET indicator light in the instrument panel then blinks to warn the driver.

c If the SET indicator light blinks, turn the cruise control main switch off and have the system checked by a NISSAN dealer.

Z REVIEW COPY—2007 Xterra (xtr) Owners Manual—USA_English (nna) 02/27/07—debbie X

pushing

c The SET indicator light may blink when the cruise control main switch is turned ON while ACCEL/RES, COAST/SET, or CANCEL switch (located on the steering wheel). To properly set the cruise control system, use the following pro- cedures.

the

WARNING

Do not use the cruise control when driving under the following conditions: c When it is not possible to keep the

vehicle at a set speed.

c In heavy traffic or in traffic that varies in

speed.

c On winding or hilly roads. c On slippery roads (rain, snow, ice, etc.). c In very windy areas. Doing so could cause a loss of vehicle control and result in an accident.

CAUTION

On manual transmission models, do not shift into N (Neutral) without depressing the clutch pedal when the cruise control is set. Should this occur, depress the clutch pedal and turn the main switch off imme- diately. Failure to do so may cause engine damage. CRUISE CONTROL OPERATIONS The cruise control allows driving at a speed be- tween 25 - 89 MPH (40 - 144 km/h) without keeping your foot on the accelerator pedal. To turn on the cruise control, push the main switch. The CRUISE indicator light in the instru- ment panel comes on. To set cruising speed, accelerate the vehicle to the desired speed, push the COAST/SET switch and release it. The SET indicator light in the instrument panel comes on. Take your foot off the accelerator pedal. Your vehicle maintains the set speed. c To pass another vehicle, depress the ac- celerator pedal. When you release the pedal, the vehicle returns to the previously set speed.

c The vehicle may not maintain the set speed when going up or down steep hills. If this happens, drive without the cruise control.

To cancel the preset speed, use one of the following three methods. c Push the CANCEL button; the SET indicator

light in the instrument panel goes out.

c Tap the brake pedal; the SET indicator light

goes out.

c Turn the main switch off. Both the CRUISE indicator light and SET indicator light in the instrument panel go out.

The cruise control is automatically canceled and the SET light in the instrument panel goes out if: c you depress the brake or clutch pedal while pushing the ACCEL/RES or COAST/SET switch. The preset speed is deleted from memory.

c the vehicle slows down more than 8 MPH

(13 km/h) below the set speed.

c you depress the clutch pedal (manual trans- mission), or move the shift selector lever to N (Neutral) (automatic transmission).

Starting and driving 5-19

Z REVIEW COPY—2007 Xterra (xtr) Owners Manual—USA_English (nna) 02/27/07—debbie X

BREAK-IN SCHEDULE

INCREASING FUEL ECONOMY

CAUTION

During the first 1,200 miles (2,000 km), follow these recommendations to obtain maximum engine performance and en- sure the future reliability and economy of your new vehicle. Failure to follow these recommendations may result in short- ened engine life and reduced engine performance. c Avoid driving for long periods at constant speed, either fast or slow, and do not run the engine over 4,000 rpm.

c Do not accelerate at full throttle in any gear. c Avoid quick starts. c Avoid hard braking as much as possible. c Do not tow a trailer for the first 500 miles (800 km). Your engine, axle or other parts could be damaged.

c Accelerate slowly and smoothly. Maintain cruising speeds with a constant accelerator position.

c Drive at moderate speeds on the highway. Driving at high speed lowers fuel economy. c Avoid unnecessary stopping and braking. Maintain a safe distance behind other ve- hicles.

c Use a proper gear range which suits road conditions. On level roads, shift into high gear as soon as possible.

c Avoid unnecessary engine idling. c Keep your engine tuned up. c Follow the recommended periodic mainte-

nance schedule.

c Keep the tires inflated to the correct pres- sure. Low tire pressure increases tire wear and lowers fuel economy.

c Keep the front wheels in correct alignment. Improper alignment increases tire wear and lowers fuel economy.

c Air

conditioner operation

fuel economy. Use the air conditioner only when necessary.

lowers

To reset at a faster cruising speed, use one of the following three methods. c Depress the accelerator pedal. When the vehicle attains the desired speed, push and release the COAST/SET switch.

c Push and hold the ACCEL/RES switch. When the vehicle attains the speed you de- sire, release the switch.

c Push and release the ACCEL/RES switch. Each time you do this, the set speed in- creases by about 1 MPH (1.6 km/h).

To reset at a slower cruising speed, use one of the following three methods. c Lightly tap the brake pedal. When the ve- hicle attains the desired speed, push the COAST/SET switch and release it.

c Push and hold the COAST/SET switch. Re- lease the switch when the vehicle slows to the desired speed.

c Push and release the COAST/SET switch. Each time you do this, the set speed de- creases by about 1 MPH (1.6 km/h).

To resume the preset speed, push and re- lease the ACCEL/RES switch. The vehicle re- turns to the last set cruising speed when the vehicle speed is over 25 MPH (40 km/h).

5-20 Starting and driving

Z REVIEW COPY—2007 Xterra (xtr) Owners Manual—USA_English (nna) 02/27/07—debbie X

c When cruising at highway speeds, it is more economical to use the air conditioner and leave the windows closed to reduce drag.

Use 4H or 4L position only when necessary. Four-wheel drive operation low- ers fuel economy.

USING FOUR WHEEL DRIVE

(4WD)

WARNING

CAUTION

to raise two wheels off

c For 4WD equipped vehicles, do not at- tempt the ground and shift the transmission to any drive or reverse position with the engine running. Doing so may result in drivetrain damage or unexpected ve- hicle movement which could result in serious vehicle damage or personal injury.

c Do not attempt to test a 4WD equipped vehicle on a 2-wheel dynamometer (such as the dynamometers used by some states for emissions testing), or similar equipment even if the other two wheels are raised off the ground. Make sure you inform test facility personnel that your vehicle is equipped with 4WD before it is placed on a dynamometer. Using the wrong test equipment may result in drivetrain damage or unex- pected vehicle movement which could result in serious vehicle damage or per- sonal injury.

c Do not drive the vehicle in the 4H or 4LO position on dry hard surface roads. Driv- ing on dry, hard surfaces in 4H or 4LO may cause unnecessary noise, tire wear and increased fuel consumption. If the 4WD warning light turns on when you are driving on dry hard surface roads: (cid:150) in the 4H position, shift the 4WD shift

switch to 2WD.

(cid:150) in the 4LO position for automatic transmission vehicles, stop the ve- hicle and shift the transmission se- lector to the N position with the brake pedal depressed and shift the 4WD shift switch to 2WD.

(cid:150) in the 4LO position for manual trans- mission vehicles, stop the vehicle and shift the transmission shift lever to the N position with the clutch pedal depressed and shift the 4WD shift switch to 2WD.

c If the warning light is still on after the above operation, have your vehicle checked by a NISSAN dealer as soon as possible.

Starting and driving 5-21

Z REVIEW COPY—2007 Xterra (xtr) Owners Manual—USA_English (nna) 02/27/07—debbie X

TRANSFER CASE SHIFTING PROCEDURES The part time 4WD system provides 3 positions (2WD, 4H and 4LO), so you can select the desired drive mode according to the driving conditions. 2WD or 4WD shift procedure:

4WD Shift

Switch Position

Wheels Driven

Indicator Light

4WD shift

Transfer 4LO position

Use Conditions

4WD Shift Procedure

2WD

4H

4LO

Rear wheels

4 wheels

Neutral

4 wheels

5-22 Starting and driving

For driving on dry, paved roads (Economy drive) or state dyna- mometer I/M testing

For driving on rocky, sandy or snow-covered roads

Neutral disengages the auto- matic transmission mechanical parking lock, which will allow the vehicle to roll. Do not leave the transfer shift position in Neutral.*2

For use when maximum power and traction is required (for example: on steep grades or rocky, sandy, muddy roads)

*1
May blink

Illuminated

Move the 4WD switch. 2WD <(cid:151)> 4H 4WD shift indicator light will indicate transfer shift position en- gaged.

1. Stop the vehicle. 2. For automatic transmission vehicles: Shift the transmission selector to the (N) position with the brake pedal depressed. For manual transmission vehicles: Shift the transmission shift lever to the (N) position with the clutch depressed.

3. For automatic transmission vehicles: Depress and turn the

4WD shift switch to 4LO or 4H with the brake pedal de- pressed. For manual transmission vehicles: Depress and turn the 4WD switch to 4LO or 4H with the clutch pedal depressed.

THE TRANSFER CASE DOES NOT ENGAGE BETWEEN 4H AND 4LO (OR 4LO TO 4H) UNLESS YOU HAVE FIRST STOPPED THE VEHICLE, DEPRESSED THE BRAKE PEDAL AND MOVED THE TRANSMISSION SELECTOR TO NEUTRAL FOR AUTOMATIC TRANSMISSION VEHICLES. FOR MANUAL TRANSMISSION VEHICLES YOU MUST MOVE THE TRANS- MISSION SHIFT LEVER TO NEUTRAL. *3

Z REVIEW COPY—2007 Xterra (xtr) Owners Manual—USA_English (nna) 02/27/07—debbie X

*1: Before moving the transmission selector or shift lever from neutral, wait until the 4LO indicator light stays on steady. This indicates that the 4WD shift procedure is completed and the transfer gear is correctly set in the 4LO position. If the vehicle is shifted into gear before the indicator is on steady, the transfer gear may grind, not engage correctly or stay in the neutral position. - If the 4WD warning light illuminates, perform the following procedure to return the transfer case to correct operating condition. 1. Turn off the engine by turning the ignition switch 9OFF9. 2. Start the engine. - Check that the 4WD warning light turns off. If the 4WD warning light illuminates, have the system checked by a NISSAN dealer. 3. Apply the parking brake, for automatic transmission vehicles, depress the brake pedal and move the transmission selector to Neutral position. For

manual transmission vehicles, move the transmission shift lever to Neutral position.

4. With the brake pedal depressed on automatic transmission vehicles or with the clutch pedal depressed on manual transmission vehicles, move the

4WD shift switch to desired mode.

- Be sure to wait until the transfer gear change completes before shifting the transmission selector or transmission shift lever from Neutral position.

*2: While changing in and out of 4LO, the ignition key must be ON and the vehicle(cid:146)s engine must be running for a shift to take place and for the indicator

lights (4WD shift and 4LO position indicator) to be operable. Otherwise, the shift will not take place and no indicator lights will be on or flashing.

*3: Make sure the transfer 4LO position indicator light turns on when you shift the 4WD shift switch to 4LO. The

also turn on when 4LO is selected. See (cid:147)Vehicle dynamic control system(cid:148) later in this section.

indicator light (if so equipped) will

Starting and driving 5-23

Z REVIEW COPY—2007 Xterra (xtr) Owners Manual—USA_English (nna) 02/27/07—arosenma X

The transfer case 4WD shift switch is used to select either 2WD or 4WD depending on the driving conditions. There are three types of drive modes available, 2WD, 4H and 4LO.

The 4WD shift switch electronically controls the transfer case operation. Rotate the switch to move between each mode, 2WD, 4H and 4LO. To change into or out of 4LO, the vehicle MUST be stationary, shift the transmission selector or transmission shift lever to Neu- tral (N), and for automatic transmission vehicles depress the brake pedal or for manual transmission vehicles depress the clutch pedal. The switch must be de- pressed and turned when changing into or out of 4LO.

WARNING

c When parking, apply the parking brake before stopping the engine and make sure that the 4WD shift indicator light is on and the ATP warning light goes off. Otherwise, the vehicle could unexpect- edly move even if the automatic trans- mission is in the P position.

5-24 Starting and driving

c The 4LO indicator light must stop blink- ing and remain illuminated or turn off before shifting the transmission into gear. If the transmission selector or transmission shift lever is shifted from the (N) position to any other gear when the 4LO indicator light is blinking, the vehicle may move unexpectedly.

CAUTION

c Never shift the 4WD shift switch be-

tween 4LO and 4H while driving.

c The 4H position provides greater trac- tion. Avoid excessive speed, as it will cause increased fuel consumption and higher oil temperatures, and could damage components. drivetrain Speeds over 62.5 MPH (100 km/h) in 4H is not recommended.

c The 4LO position provides maximum power and traction. Avoid raising ve- hicle speed excessively, as the maxi- mum speed is approximately 31 MPH (50 km/h).

c When driving straight, shift the 4WD shift switch to the 2WD or 4H position. Do not move the 4WD shift switch when making a turn or reversing.

c Do not shift the 4WD shift switch (be- tween 2WD and 4H) while driving on steep downhill grades. Use the engine brake and low automatic transmission gears (D1 or D2) or manual transmis- sion (1st gear or 2nd gear) for engine braking.

c Do not operate the 4WD shift switch (between 2WD and 4H) with the rear wheels spinning.

c Do not drive on dry hard surface roads in the 4H or 4LO position. Driving on dry hard surfaces in 4H or 4LO may cause unnecessary noise and tire wear. NISSAN recommends driving in the 2WD position under these conditions.

c The 4WD transfer case may not be shifted between 4H and 4LO at low am- bient temperatures and the transfer 4LO position indicator light may blink even when the 4WD shift switch is shifted. After driving for a while you can change the 4WD transfer case between 4H and 4LO.

When driving on rough roads, c Set the 4WD shift switch to 4H or 4LO. c Drive carefully according to the road surface

conditions.

Z REVIEW COPY—2007 Xterra (xtr) Owners Manual—USA_English (nna) 02/27/07—debbie X

When the vehicle is stuck, c Set the 4WD shift switch to 4H or 4LO. c Use the Electronic Locking Rear Differential (E-Lock) system (if so equipped). Turn the switch ON while the vehicle is stationary and apply the throttle to try to free the vehicle.

c If it is difficult to free the vehicle, rock the vehicle back and forth between reverse and drive gears.

c If the vehicle is stuck deep in mud, place stones or wooden blocks under the tires. Then try the recovery procedures above. Tire chains may be effective.

CAUTION

c Do not spin the tires excessively. Tires will sink deep into the mud, making it difficult to free the vehicle.

c Avoid shifting gears with the engine running at high speeds as this may cause malfunction.

clutch is released and not because of a malfunction.

CAUTION

c When driving straight, shift the 4WD shift switch to the 2WD or 4H position. Do not move the 4WD shift switch when making a turn or reversing.

c Do not shift the 4WD shift switch while driving on steep downhill grades. Use the engine brake and low automatic transmission gears (D1 or D2) or manual transmission (1st gear or 2nd gear) for engine braking.

c Do not operate the 4WD shift switch

with the rear wheels spinning.

c Before placing the 4WD shift switch in the 4H position from 2WD, ensure the vehicle speed is less than 62.5 MPH (100 km/h). Failure to do so can dam- age the 4WD system.

c Never shift the 4WD shift switch be-

tween 4LO and 4H while driving.

4WD shift indicator light

Starting and driving 5-25

LSD0145

4WD shift switch operations c Shift the 4WD shift switch to either the 2WD, 4H or 4LO position, depending on driving conditions.

c If the 4WD shift switch is operated while making a turn, accelerating or decelerating or if the key switch is turned off while in the 4H or 4LO posi- tion, you may feel a jolt. This is not abnormal.

c When the vehicle is stopped after mak- ing a turn, you may feel a slight jolt after the selector lever is shifted to N or P. This occurs because the transfer

Z REVIEW COPY—2007 Xterra (xtr) Owners Manual—USA_English (nna) 02/27/07—debbie X

LSD0147
The 4WD shift indicator light is located in the odometer display.

The light should turn off within 1 second after turning the ignition switch to the ON position.

While the engine is running, the 4WD shift indi- cator light will illuminate the position selected by the 4WD shift switch. c The 4WD shift indicator light may blink while shifting from one drive mode to the other. When the shifting is com- pleted, the 4WD shift indicator light will come on.

5-26 Starting and driving

c If the 4WD warning light comes on, the

The 4WD warning light is located in the meter.

4WD indicator light goes out.

CAUTION

If the 4WD shift indicator light indication changes to 2WD when the 4WD shift switch is shifted to the 4H position at low ambient temperatures, the 2WD mode may be being engaged due to malfunc- tioning drive system. If the indicator does not return to normal and the 4WD warning light comes on, have the system checked by the nearest NISSAN dealer.

4WD warning light

Warning light

Comes on or blinks

when:

Comes on

Blinks slowly

There is a malfunc- tion in the 4(cid:150)wheel

drive system

The difference in wheel rotation is

large

The 4WD warning light comes on when the key switch is turned to ON. It turns off soon after the engine is started.

If any malfunction occurs in the 4WD system when the key switch is ON, the warning light will either remain illuminated or blink.

If the 4WD warning light comes on, the 4WD shift indicator light goes out.

A large difference between the diameters of front and rear wheels will make the warning light blink slowly (about once per two seconds). Change the 4WD shift switch into 2WD and do not drive fast.

CAUTION

c If the warning light comes on or blinks slowly during operation, have your ve- hicle checked by a NISSAN dealer as soon as possible.

c Shifting between 4H and 4LO is not recommended when the 4WD warning light turns on.

Z REVIEW COPY—2007 Xterra (xtr) Owners Manual—USA_English (nna) 02/27/07—debbie X

(cid:150) in the 4LO position for manual trans- mission vehicles, stop the vehicle and shift the transmission shift lever to the N position with the clutch pedal depressed and shift the 4WD shift switch to 2WD.

c If the warning light is still on after the above operation, have your vehicle checked by a NISSAN dealer as soon as possible.

c When the warning light comes on, the 2WD mode may be engaged even if the 4WD shift switch is in 4H. Be especially careful when driving. If corresponding parts are malfunctioning, the 4WD mode will not be engaged even if the 4WD shift switch is shifted.

c Do not drive the vehicle in the 4H or 4LO position on dry hard surface roads. Driv- ing on dry, hard surfaces in 4H or 4LO may cause unnecessary noise, tire wear and increased fuel consumption. If the 4WD warning light turns on when you are driving on dry hard surface roads: (cid:150) in the 4H position, shift the 4WD shift

switch to 2WD.

(cid:150) in the 4LO position for automatic transmission vehicles, stop the ve- hicle and shift the transmission se- lector to the N position with the brake pedal depressed and shift the 4WD shift switch to 2WD.

ELECTRONIC LOCKING REAR DIFFERENTIAL (E-Lock) SYSTEM (if so equipped) The E-Lock system can provide additional trac- tion and should only be used when a vehicle has become or is becoming stuck. This system oper- ates by electronically (cid:147)locking(cid:148) the two rear drive wheels together, allowing them to turn at the same speed. The system is used when it is not possible to free a stuck vehicle even when using the 4LO position (4 wheel drive vehicles).

When added traction is required, activate the E-Lock system by pushing the switch ON. See (cid:147)Electronic Locking Rear Differential (E-Lock) system switch(cid:148) in the (cid:147)Instruments and Controls(cid:148) section. Once the system fully engages, the indi- cator light in the instrument panel will remain ON. When the system is activated, both rear wheels will engage, providing added traction.

The rear wheels may momentarily slip or move to engage the system, and the system will only engage up to approximately 4 MPH (7 km/h). Once the vehicle is free, the system should be turned OFF and driving resumed.

The Anti-Lock Brake (ABS) system is disabled and the ABS light illuminates when the E-Lock system is ON. Also, the Vehicle Dynamic Control (VDC) system is disabled and the VDC light illuminates when the E-Lock system is ON.

Starting and driving 5-27

Z REVIEW COPY—2007 Xterra (xtr) Owners Manual—USA_English (nna) 02/27/07—debbie X

WARNING

CAUTION

c Never leave the E-Lock system ON when driving on paved or hard-surfaced roads. Turning the vehicle may result in the rear wheels slipping and result in an accident and personal injury. After us- ing the E-Lock system to free the ve- hicle, turn the system OFF.

c Use the E-Lock system only when free- ing a stuck vehicle. Try the 4LO position before using the E-Lock system. Never use the E-Lock system on a slippery road surface such as snow or ice sur- face. Using the E-Lock system when driving in these road conditions may cause unexpected movement of the ve- hicle during engine braking, accelerat- ing or turning, which may result in an accident and serious personal injury.

c After using the E-Lock system, turn the switch OFF to prevent possible damage to driveline components from extended use.

c Do not drive the vehicle at speeds faster than 12 mph (20 km/h) when the system is engaged. Doing so could damage drivetrain components.

c Do not turn on the E-lock system while the tires are spinning. Doing so could damage drivetrain components.

5-28 Starting and driving

Z REVIEW COPY—2007 Xterra (xtr) Owners Manual—USA_English (nna) 02/27/07—debbie X

PARKING/PARKING ON HILLS

WARNING

c Do not stop or park the vehicle over flammable materials such as dry grass, waste paper or rags. They may ignite and cause a fire.

c Safe parking procedures require that both the parking brake be set and the transmission placed into P (Park) for automatic transmission models or in an appropriate gear for manual transmis- sion models. Failure to do so could cause the vehicle to move unexpectedly or roll away and result in an accident. Make sure the shift lever has been

WSD0050

pushed as far forward as it can go and cannot be moved without depressing the foot brake pedal.

c Never leave the engine running while

the vehicle is unattended.

c Do not leave children unattended inside the vehicle. They could unknowingly ac- tivate switches or controls. Unattended children could become involved in seri- ous accidents.

1. Firmly apply the parking brake. 2. Manual transmission models:

Place the shift lever in the R (Reverse) posi- tion. When parking on an uphill grade, place the shift lever in 1st gear. Automatic transmission models: Move the shift selector lever to the P (Park) position.

3. To help prevent the vehicle from rolling into traffic when parked on an incline, it is a good practice to turn the wheels as illustrated. c HEADED DOWNHILL WITH CURB: sA

Turn the wheels into the curb and move the vehicle forward until the curb side wheel gently touches the curb.

c HEADED UPHILL WITH CURB: sB

Turn the wheels away from the curb and move the vehicle back until the curb side wheel gently touches the curb.

c HEADED UPHILL OR DOWNHILL, NO

CURB: sC Turn the wheels toward the side of the road so the vehicle will move away from the cen- ter of the road if it moves.

4. Turn the ignition key to the LOCK position

and remove the key.

Starting and driving 5-29

Z REVIEW COPY—2007 Xterra (xtr) Owners Manual—USA_English (nna) 02/27/07—debbie X

POWER STEERING

BRAKE SYSTEM

The power assisted steering uses a hydraulic pump, driven by the engine, to assist steering. If the engine stops or the drive belt breaks, you will still have control of the vehicle. However, much greater steering effort is needed, especially in sharp turns and at low speeds.

WARNING

If the engine is not running or is turned off while driving, the power assist for the steering will not work. Steering will be harder to operate.

5-30 Starting and driving

The brake system has two separate hydraulic circuits. If one circuit malfunctions, you will still have braking at two wheels. BRAKE PRECAUTIONS Vacuum assisted brakes The brake booster aids braking by using engine vacuum. If the engine stops, you can stop the vehicle by depressing the brake pedal. However, greater foot pressure on the brake pedal will be required to stop the vehicle and stopping dis- tance will be longer. Using the brakes Avoid resting your foot on the brake pedal while driving. This will overheat the brakes, wear out the brakes and pads faster, and reduce gas mileage.

To help reduce brake wear and to prevent the brakes from overheating, reduce speed and downshift to a lower gear before going down a slope or long grade. Overheated brakes may reduce braking performance and could result in loss of vehicle control.

WARNING

c While driving on a slippery surface, be careful when braking, accelerating or downshifting. Abrupt braking or accel- erating could cause the wheels to skid and result in an accident.

c If the engine is not running or is turned off while driving, the power assist for the brakes will not work. Braking will be harder.

Wet brakes When the vehicle is washed or driven through water, the brakes may get wet. As a result, your braking distance will be longer and the vehicle may pull to one side during braking.

To dry the brakes, drive the vehicle at a safe speed while lightly pressing the brake pedal to heat up the brakes. Do this until the brakes return to normal. Avoid driving the vehicle at high speeds until the brakes function correctly. Parking brake break-in Break-in the parking brake shoes whenever the stopping effect of the parking brake is weakened or whenever the parking brake shoes and/or drum/rotors are replaced, in order to assure the best brake performance.

Z REVIEW COPY—2007 Xterra (xtr) Owners Manual—USA_English (nna) 02/27/07—debbie X

This procedure is described in the vehicle service manual and can be performed by a NISSAN dealer. ANTI-LOCK BRAKING SYSTEM (ABS)

WARNING

c The Anti-lock Braking System (ABS) is a sophisticated device, but it cannot pre- vent accidents resulting from careless or dangerous driving techniques. It can help maintain vehicle control during braking on slippery surfaces. Remem- ber that stopping distances on slippery surfaces will be longer than on normal surfaces even with ABS. Stopping dis- tances may also be longer on rough, gravel or snow covered roads, or if you are using tire chains. Always maintain a safe distance from the vehicle in front of you. Ultimately, the driver is respon- sible for safety.

c Tire type and condition may also affect

braking effectiveness. (cid:150) When replacing tires,

the specified size of tires on all four wheels.

install

(cid:150) When installing a spare tire, make sure that it is the proper size and type as specified on the Tire and Loading Information label. See (cid:147)Tire and Loading Information label(cid:148) in the (cid:147)Technical and consumer informa- tion(cid:148) section of this manual.

(cid:150) For

detailed

information,

see (cid:147)Wheels and tires(cid:148) in the (cid:147)Mainte- nance and do-it-yourself(cid:148) section of this manual.

The Anti-lock Braking System (ABS) controls the brakes so the wheels do not lock during hard braking or when braking on slippery surfaces. The system detects the rotation speed at each wheel and varies the brake fluid pressure to pre- vent each wheel from locking and sliding. By preventing each wheel from locking, the system helps the driver maintain steering control and helps to minimize swerving and spinning on slip- pery surfaces. Using the system Depress the brake pedal and hold it down. De- press the brake pedal with firm steady pressure, but do not pump the brakes. The ABS will oper- ate to prevent the wheels from locking up. Steer the vehicle to avoid obstacles.

WARNING

Do not pump the brake pedal. Doing so may stopping distances.

increased

result

in

Self-test feature The ABS includes electronic sensors, electric pumps, hydraulic solenoids and a computer. The computer has a built-in diagnostic feature that tests the system each time you start the engine and move the vehicle at a low speed in forward or reverse. When the self-test occurs, you may hear a (cid:147)clunk(cid:148) noise and/or feel a pulsation in the brake pedal. This is normal and does not indicate a malfunction. If the computer senses a malfunc- tion, it switches the ABS off and illuminates the ABS warning light on the instrument panel. The brake system then operates normally, but without anti-lock assistance.

If the ABS warning light illuminates during the self-test or while driving, have the vehicle checked by a NISSAN dealer. Normal operation The ABS operates at speeds above 3 - 6 MPH (5
- 10 km/h).

Starting and driving 5-31

Z REVIEW COPY—2007 Xterra (xtr) Owners Manual—USA_English (nna) 02/27/07—debbie X

When the ABS senses that one or more wheels are close to locking up, the system electronically controls the pressure applied to each brake. This action is similar to pumping the brakes very quickly. You may feel a pulsation in the brake pedal and hear a noise from under the hood or feel a vibration from the actuator when it is oper- ating. This is normal and indicates that the ABS is operating properly. However, the pulsation may indicate that road conditions are hazardous and extra care is required while driving.

5-32 Starting and driving

ACTIVE BRAKE LIMITED SLIP (ABLS) SYSTEM (if so equipped)

VEHICLE DYNAMIC CONTROL (VDC) SYSTEM

c ABLS is a form of traction control using sensors from the Anti-lock Brake System (ABS) to transfer power from a slipping drive wheel to a wheel with more traction. The ABLS system applies braking to the slipping wheel, which helps redirect power to an- other wheel.

c On 4WD models the ABLS system operates in both 4H and 4LO modes. If 4WD mode is engaged, the ABLS system will operate for both drive axles. On 2WD vehicles, the ABLS system operates on the drive axle only.

c The ABLS system is always ON unless the system detects brake pad overheating. If high brake pad temperature is detected, it will turn OFF, but normal brake function will continue. ABLS will function even when the VDC system (if so equipped) is turned OFF.

WARNING

The ABLS system provides increased trac- tion, but will not prevent accidents due to abrupt steering operation or by careless driving or dangerous driving practices. Reduce vehicle speed and be especially careful when driving and cornering on slippery surfaces, and always drive carefully.

When accelerating or driving on slippery sur- faces, the tires may spin or slide. With the Vehicle Dynamic Control (VDC) system, sensors detect these movements and control the braking and engine output to help improve vehicle stability. c When the vehicle dynamic control (VDC) system is operating, the SLIP indicator in the instrument panel blinks.

c If the 4WD transfer case is shifted into 4LO indicator light will come on and the the VDC system will be turned off. See (cid:147)Transfer case shifting procedures(cid:148) earlier in this section.

c If the SLIP indicator blinks, the road condi- tions are slippery. Be sure to adjust your speed and driving to these conditions. See (cid:147)Slip indicator light(cid:148), and (cid:147)Vehicle dynamic control (VDC) off indicator light(cid:148) in the (cid:147)In- struments and controls(cid:148) section.

If the battery is removed or discharged, the trac- tion control system may be disabled and the SLIP and indicator lights will not turn off after 2 seconds when the ignition switch is turned to the ON position. Perform the following procedure to reset the system: c Start the engine and set the steering wheel

in the straight forward position.

Z REVIEW COPY—2007 Xterra (xtr) Owners Manual—USA_English (nna) 02/27/07—debbie X

c Drive the vehicle at speeds above 10 mph

(15 km/h) for at least 10 minutes.

c The VDC OFF indicator light should go off indicating the traction control system is op- erational.

c If you interrupt the reset procedure by turn- ing the ignition off, you will need to restart the reset procedure.

If after driving the vehicle for more than 10 min- utes and the SLIP and lights remain illumi- nated in the instrument panel, have the vehicle dynamic control system checked by a NISSAN dealer. If the vehicle is operated with the vehicle dynamic control system off using the VDC OFF switch, most VDC functions will be turned off. The VDC system will still try to transfer power from a slip- ping drive wheel to one with more traction when the VDC system switch is OFF. The SLIP indica- tor will flash if wheel spin is detected. The ABS will still operate with the VDC system off. When the VDC system is operating, you may feel a pulsation in the brake pedal and hear a noise or vibration from under the hood. This is normal and indicates that the VDC system is working prop- erly.

The computer has a built in diagnostic feature that tests the system each time you start the engine and move the vehicle forward or in reverse at a slow speed. When the self-test occurs, you may hear a clunk noise and/or feel a pulsation in the brake pedal. This is normal and is not an indication of a malfunction.

WARNING

c The vehicle dynamic control system is designed to help improve driving stabil- ity but does not prevent accidents due