CAUTION
O NEVER remove dirt, sand or other debris from the passenger compart- ment by washing it out with a hose. Remove dirt with a vacuum cleaner or broom.
O Never allow water or other liquids to come in contact with electronic com- ponents inside the vehicle as this may damage them.
Chemicals used for road surface de-icing are extremely corrosive. They accelerate corrosion and deterioration of underbody components such as the exhaust system, fuel and brake lines, brake cables, floor pan and fenders. In winter, cleaned periodically. For additional protection against rust and corrosion, which may be required in some areas, consult an authorized NISSAN dealer.
the underbody must be
7-6 Appearance and care
Z X
MEMO
Appearance and care 7-7
Z X
8 Maintenance and do-it-yourself
Maintenance requirements.....................................8-2
General maintenance.............................................8-3
Explanation of general maintenance
items ..................................................................8-3
Exterior maintenance.........................................8-3
Interior maintenance..........................................8-3
Maintenance precautions .......................................8-5
Engine compartment check locations ....................8-7
Engine cooling system .........................................8-10
Checking engine coolant level ........................8-10
Changing engine coolant ................................8-11
Engine oil .............................................................8-11
Checking engine oil level ................................8-11
Changing engine oil ........................................8-13
Changing engine oil filter.................................8-14
Automatic transmission fluid ................................8-15
Temperature conditions for checking ..............8-15
Power steering fluid..............................................8-17
Brake and clutch fluid...........................................8-17
Window washer fluid ............................................8-18
Window washer fluid reservoir ........................8-18
Battery ..................................................................8-19
Jump starting...................................................8-20
Drive belts ............................................................8-20
Spark plugs ..........................................................8-21
Replacing spark plugs
(except supercharger) .....................................8-22
Replacing spark plugs
(with supercharger)..........................................8-23
Air cleaner ............................................................8-23
Windshield wiper blades ......................................8-25
Cleaning ..........................................................8-25
Replacing.........................................................8-25
Parking brake and brake pedal............................8-27
Checking parking brake...................................8-27
Checking brake pedal .....................................8-27
Brake booster ..................................................8-28
Clutch pedal .........................................................8-29
Checking clutch pedal .....................................8-29
Fuses....................................................................8-30
Passenger compartment .................................8-30
Keyfob battery replacement .................................8-31
Lights....................................................................8-32
Headlights........................................................8-32
Z X
Fog lights (if so equipped)...............................8-33
Exterior and interior lights ...............................8-34
Wheels and tires ..................................................8-37
Tire pressure ...................................................8-37
Types of tires...................................................8-38
Tire chains .......................................................8-38
Changing wheels and tires..............................8-39
Z X
forms the best job to meet the maintenance requirements on your vehicle — in a reliable and economic way.
MAINTENANCE REQUIREMENTS
Your new NISSAN has been designed to have minimum maintenance requirements with longer service intervals to save you both time and money. However, some day- to-day and regular maintenance is essential to maintain your NISSAN’s good mechani- cal condition, as well as its emission and engine performance. It is the owner’s responsibility to make sure that the scheduled maintenance, as well as general maintenance, is performed. As the vehicle owner, you are the only one who can ensure that your vehicle receives proper maintenance. You are a vital link in the maintenance chain. Scheduled maintenance For your convenience, both required and optional scheduled maintenance items are described and listed in your ‘‘NISSAN Ser- vice and Maintenance Guide.’’ You must refer to that guide to ensure that necessary maintenance is performed on your NISSAN at regular intervals. General maintenance General maintenance includes those items which should be checked during normal 8-2 Maintenance and do-it-yourself
day-to-day operation of the vehicle. They are essential if your vehicle is to continue to operate properly. It is your responsibility to perform these maintenance procedures regularly as prescribed. Performing general maintenance checks re- quires minimal mechanical skill and only a few general automotive tools. These checks or inspections can be done by yourself, a qualified technician or, if you prefer, an authorized NISSAN dealer. Where to go for service If maintenance service is required or your vehicle appears to malfunction, have the systems checked and tuned by an autho- rized NISSAN dealer. NISSAN technicians are well-trained spe- cialists who and are kept up-to-date with the latest service information through technical bulletins, service tips, and in-dealership training programs. They are completely qualified to work on NISSAN vehicles before they work on your vehicle, rather than after they have worked on it. You can be confident that an authorized NISSAN dealer’s service department per-
Z X
GENERAL MAINTENANCE
During the normal day-to-day operation of the vehicle, general maintenance should be performed regularly as prescribed in this section. If you detect any unusual sounds, vibrations or smells, be sure to check for the cause or have an authorized NISSAN dealer do it promptly. In addition, you should notify an authorized NISSAN dealer if you think that repairs are required. When performing any checks or mainte- nance work, closely observe the precau- tions in this ‘‘Maintenance and do-it- yourself’’ section of this manual. EXPLANATION OF GENERAL MAINTENANCE ITEMS Additional information on the following items with an ‘‘*’’ is found later in this section. EXTERIOR MAINTENANCE Outside the vehicle The maintenance items listed here should be performed from time to time, unless otherwise specified. Tires* Check the pressure with a gauge at least once a month and always prior to long
distance trips, including the spare, and ad- just to the specified pressure if necessary. Check carefully for damage, cuts or exces- sive wear. Wheel nuts* When checking the tires, make sure no wheel nuts are missing, and check for any loose wheel nuts. Tighten if necessary. Tire rotation* Tires should be rotated every 7,500 miles (12,000 km). Wheel alignment and balance If the ve- hicle should pull to either side while driving on a straight and level road, or if you detect uneven or abnormal tire wear, there may be a need for wheel alignment. If the steering wheel or seat vibrates at normal highway speeds, wheel balancing may be needed. O For additional information regarding tires, refer to ‘‘Important Tire Safety Informa- tion’’ in the Warranty Information Booklet (US) or ‘‘Tire Safety Information’’ in the Warranty and Roadside Assistance infor- mation booklet (Canada).
Windshield Clean the windshield on a regular basis. Check the windshield at least every six months for cracks or other dam-
age. Have a damaged windshield repaired by a qualified repair facility. Windshield wiper blades* Check for cracks or wear if they do not wipe properly. Doors, hood and tailgate Check that the doors, hood and tailgate operate properly. Also ensure that all latches lock securely. Lubricate hinges, latches, rollers and links if necessary. Make sure that the secondary latch keeps the hood from opening when the primary latch is released. When driving in areas using road salt or other corrosive materials, check lubrication frequently. Lights* Clean the headlights on a regular basis. Make sure that the headlights, stop lights, tail lights, turn signal lights, and other lights are all operating properly and installed securely. Also check headlight aim. INTERIOR MAINTENANCE The maintenance items listed here should be checked on a regular basis, such as when performing periodic maintenance, cleaning the vehicle, etc.
Maintenance and do-it-yourself 8-3
Z X
Additional information on the following items with an ‘‘*’’ is found later in this section. Warning lights and chimes Make sure all warning lights and chimes are operating properly. Windshield wiper and washer* Check that the wipers and washer operate properly and that the wipers do not streak. Windshield defroster Check that the air comes out of the defroster outlets properly and in sufficient quantity when operating the heater or air conditioner. Steering wheel Check for changes in the steering conditions, such as excessive free- play, hard steering or strange noises. Seats Check seat position controls such as seat adjusters, seatback recliner, etc. to ensure they operate smoothly and all latches lock securely in every position. Check that the head restraints move up and down smoothly and the locks (if so equipped) hold securely in all latched posi- tions. Seat belts Check that all parts of the seat belt system (e.g., buckles, anchors, adjust- 8-4 Maintenance and do-it-yourself
ers and retractors) operate properly and smoothly, and are installed securely. Check the belt webbing for cuts, fraying, wear or damage. Accelerator pedal Check the pedal for smooth operation and make sure the pedal does not catch or require uneven effort. Keep the floor mat away from the pedal. Clutch pedal* Make sure the pedal oper- ates smoothly and check that it has the proper free travel. Brakes Check that the brakes do not pull the vehicle to one side when applied. Brake pedal and booster* Check the pedal for smooth operation and make sure it has the proper distance under it when de- pressed fully. Check the brake booster func- tion. Be certain to keep the floor mat away from the pedal. Parking brake* Check that the lever has the proper travel and confirm that your vehicle is held securely on a fairly steep hill with only the parking brake applied. Automatic transmission P (Park) posi- tion mechanism Check that the lock re- lease button on the selector lever operates
properly and smoothly. On a fairly steep hill check that your vehicle is held securely with the selector lever in the P position without applying any brakes. Under the hood and vehicle The maintenance items listed here should be checked periodically (e.g., each time you check the engine oil or refuel). Additional information on the following items with an ‘‘*’’ is found later in this section. Windshield washer fluid* Check that there is adequate fluid in the reservoir. Engine oil level* Check the level after parking the vehicle on a level surface with the engine off. Wait a few minutes for the oil to drain back into the oil pan. Brake and clutch fluid levels* Make sure that the brake and clutch fluid level is be- tween the MIN and MAX lines on the reser- voir. Power steering fluid level* and lines Check the level when the fluid is cold, with the engine off. Check the lines for proper attachment, leaks, cracks, etc.
Z X
Underbody The underbody is frequently exposed to corrosive substances such as those used on icy roads or to control dust. It is very important to remove these sub- stances from the underbody, otherwise rust may form on the floor pan, frame, fuel lines and exhaust system. At the end of winter, the underbody should be thoroughly flushed with plain water, in those areas where mud and dirt may have accumulated. See the ‘‘Appearance and care’’ section of this manual. Fluid leaks Check under the vehicle for fuel, oil, water or other fluid leaks after the vehicle has been parked for a while. Water dripping from the air conditioner after use is normal. If you should notice any leaks or if gasoline fumes are evident, check for the cause and have it corrected immediately.
transmission fluid level* Automatic Check the level after putting the selector lever in P with the engine idling at operating temperature. Engine coolant level* Check the coolant level when the engine is cold. Radiator and hoses Check the front of the radiator and clean off any dirt, insects, leaves, etc., that may have accumulated. Make sure the hoses have no cracks, de- formation, rot or loose connections. Engine drive belts* Make sure the drive belts are not frayed, worn, cracked or oily. Battery* Check the fluid level in each cell. It should be between the MAX and MIN lines. Vehicles operated in high temperatures or under severe conditions require frequent checks of the battery fluid level. Exhaust system Make sure there are no loose supports, cracks or holes. If the sound of the exhaust seems unusual or there is a smell of exhaust fumes, immediately have the exhaust system inspected by an autho- rized NISSAN dealer. See the carbon mon- oxide warning in the ‘‘Starting and driving’’ section of this manual.
MAINTENANCE PRECAUTIONS
When performing any inspection or mainte- nance work on your vehicle, always take care to prevent serious accidental injury to yourself or damage to the vehicle. The following are general precautions which should be closely observed.
WARNING
O Park the vehicle on a level surface, apply the parking brake securely and block the wheels to prevent the ve- hicle from moving. For manual trans- mission models, move the shift lever to N (Neutral). For automatic trans- mission models, move the shift lever to P (Park).
O Be sure the ignition key is in the OFF or LOCK position when performing any parts replacement or repairs.
O Never leave the engine or automatic transmission related component harnesses disconnected while the ignition switch is in the ON position. O Never connect or disconnect the bat- tery or any transistorized compo- nent while the ignition switch is in the ON position.
Maintenance and do-it-yourself 8-5
Z X
O If you must work with the engine run- ning, keep your hands, clothing, hair and tools away from moving fans, belts, and any other moving parts.
O It is advisable to secure or remove any loose clothing and remove any jewelry, such as rings, watches, etc. before working on your vehicle.
O Always wear eye protection when-
ever you work on your vehicle.
O If you must run the engine in an enclosed space such as a garage, be sure there is proper ventilation for exhaust gases to escape.
O Never get under the vehicle while it is supported only by a jack. If it is necessary to work under the vehicle, support it with safety stands.
O Keep smoking materials, flame and sparks away from the fuel tank and battery.
O On gasoline engine models with the multiport fuel injection (MFI) system, the fuel filter or fuel lines should be serviced by an authorized NISSAN dealer because the fuel lines are under high pressure even when the engine is off.
Manual Order Information’’ in the ‘‘Technical and Consumer Information’’ Section. You should be aware that incomplete or improper servicing may result in operating difficulties or excessive emissions, and could affect your warranty coverage. If in doubt about any servicing, have it done by an authorized NISSAN dealer.
CAUTION
O Do not work under the hood while the engine is hot. Turn the engine off and wait until it cools down.
O Never connect or disconnect either the battery or any transistorized component connector while the igni- tion is on.
O Never leave the engine or automatic transmission related component harnesses disconnected while the ignition switch is in the ON position. O Avoid contact with used engine oil Improperly disposed and coolant. engine oil, engine coolant and/or other vehicle fluids can damage the environment. Always conform to lo- cal regulations for disposal of ve- hicle fluid.
This ‘‘Maintenance and do-it-yourself’’ sec- tion gives instructions regarding only those items which are relatively easy for an owner to perform. A genuine NISSAN Service Manual is also available. See ‘‘Owner’s Manual/Service
8-6 Maintenance and do-it-yourself
Z X
ENGINE COMPARTMENT CHECK LOCATIONS
KA24DE
1. Power steering fluid reservoir 2. Automatic transmission fluid dipstick (A/T
model)
3. Air cleaner 4. Engine oil filler cap 5. Engine oil dipstick 6. Brake fluid reservoir 7. Clutch fluid reservoir (M/T model) 8. Windshield washer fluid reservoir 9. Radiator cap 10. Coolant reservoir 11. Battery
WDI0087
Maintenance and do-it-yourself 8-7
Z X
1. Fuse/fusible link holder 2. Power steering fluid reservoir 3. Automatic transmission fluid dipstick (A/T
model)
4. Brake fluid reservoir 5. Clutch fluid reservoir (M/T model) 6. Air cleaner 7. Windshield washer fluid reservoir 8. Engine oil dipstick 9. Radiator cap 10. Engine oil filler cap 11. Coolant reservoir 12. Battery
8-8 Maintenance and do-it-yourself
WDI0088
Z X
1. Fuse/fusible link holder 2. Power steering fluid reservoir 3. Automatic transmission fluid dipstick (A/T
model)
4. Supercharger 5. Brake fluid reservoir 6. Air cleaner 7. Windshield washer fluid reservoir 8. Engine oil dipstick 9. Radiator cap 10. Engine oil filler cap 11. Coolant reservoir 12. Battery
WDI0089
Maintenance and do-it-yourself 8-9
Z X
WARNING
O Never remove the radiator cap when the engine is hot. Wait until the en- gine and radiator cool down. Serious burns could be caused by high pres- sure fluid escaping from the radiator. See precautions in ‘‘If your vehicle overheats’’ found in the ‘‘In case of emergency’’ section of this manual. O The radiator is equipped with a pres- sure type radiator cap. To prevent engine damage, use only a genuine NISSAN radiator cap.
ENGINE COOLING SYSTEM
The engine cooling system is filled at the factory with a high-quality, year-round, genuine NISSAN anti-freeze coolant solu- tion. The anti-freeze solution contains rust and corrosion inhibitors, therefore additional engine cooling system additives are not necessary.
CAUTION
When adding or replacing coolant, be sure to use only an ethylene glycol anti-freeze with the proper mixture ratio of 50% Genuine Nissan Anti-freeze coolant or equivalent and 50% de- mineralized or distilled water. The use of other types of coolant solutions may damage the engine cooling system.
Outside tempera- ture down to
°C
−35
°F
−30
Genuine Nissan Anti- freeze coolant or equivalent
Deminer- alized or Distilled water
50%
50%
8-10 Maintenance and do-it-yourself
ADI1026
CHECKING ENGINE COOLANT LEVEL Check the coolant level in the reservoir tank when the engine is cold. If the coolant level is below the MIN level, add coolant to the MAX level. If the reservoir tank is empty, check the coolant level in the radiator when the engine is cold. If there is insufficient coolant in the radiator, fill the radiator with coolant up to the filler opening and also add it to the reservoir tank up to the MAX level.
Z X
If the cooling system frequently requires coolant, have it checked by an autho- rized NISSAN dealer. CHANGING ENGINE COOLANT An authorized NISSAN dealer can change the engine coolant. The service procedure can be found in the NISSAN Service Manual. Improper servicing can result in reduced heater performance and engine over- heating.
WARNING
O To avoid the danger of being scalded, never change the coolant when the engine is hot.
O Never remove the radiator cap when the engine is hot. Serious burns could be caused by high pressure fluid escaping from the radiator.
O Avoid direct skin contact with used coolant. is made, wash thoroughly with soap or hand cleaner as soon as possible.
If skin contact
ENGINE OIL
O Keep coolant out of reach of children
and pets.
Engine coolant must be disposed of properly. Check your local regulations.
WDI0090
CHECKING ENGINE OIL LEVEL 1. Park the vehicle on a level surface and
apply the parking brake.
2. Start the engine and let it idle until
it
reaches operating temperature.
3. Turn off the engine. Wait a few minutes for the oil to drain back into the oil pan.
Maintenance and do-it-yourself 8-11
Z X
WDI0091
ADI1061
WDI0092
4. Remove the dipstick and wipe it clean.
Reinsert it all the way.
level.
5. Remove the dipstick again and check the oil It should be between the H (High) and L (Low) marks. If the oil level is below the L (Low) mark, remove the oil filler cap and pour recommended oil through the opening. Do not overfill.
6. Recheck oil level with dipstick. It is normal to add some oil between oil maintenance intervals or during the break-in period, depending on the sever- ity of operating conditions.
8-12 Maintenance and do-it-yourself
CAUTION
Oil level should be checked regularly. Operating the engine with an insuffi- cient amount of oil can damage the engine, and such damage is not cov- ered by warranty.
Z X
ADI1063
WDI0093
CHANGING ENGINE OIL 1. Park the vehicle on a level surface and
apply the parking brake.
2. Start
the engine and let
it reaches operating temperature, and then turn it off.
idle until
3. Remove the oil filler cap. 4. Place a large drain pan under the drain
plug.
5. Remove the drain plug with a wrench and
completely drain the oil. If the oil filter is to be changed, remove and replace it at this time. See ‘‘Chang- ing engine oil filter’’ later in this section.
WARNING
O Prolonged and repeated contact with used engine oil may cause skin can- cer.
O Try to avoid direct skin contact with used oil. If skin contact is made, wash thoroughly with soap or hand cleaner as soon as possible.
O Keep used engine oil out of reach of
children.
CAUTION
Be careful not to burn yourself. The engine oil is hot.
O Waste oil must be disposed of prop-
erly.
O Check your local regulations. 6. Clean and reinstall the drain plug and a new washer. Securely tighten the drain plug with a wrench. Do not use excessive force. Drain plug tightening torque:
22 to 29 ft-lb (29 to 39 Nzm)
Maintenance and do-it-yourself 8-13
Z X
7. Refill engine with a recommended oil through the oil filler opening then install the oil filler cap securely. See ‘‘Capacities and recommended fuel/lubricants’’ in the ‘‘Technical and consumer information’’ section for drain and refill capacity. The drain and refill capacity depends on the oil temperature and drain time. Use these specifications for reference only. Always use the dipstick to determine when the proper amount of oil is in the engine.
8. Start
the engine. Check for
leakage around the drain plug and oil filter. Cor- rect as required.
9. Turn the engine off and wait several level with the
minutes. Check the oil dipstick. Add engine oil if necessary.
8-14 Maintenance and do-it-yourself
ADI1065
WDI0094
CHANGING ENGINE OIL FILTER 1. Park the vehicle on a level surface and
apply the parking brake.
CAUTION
Be careful not to burn yourself. The engine oil may be hot.
2. Turn the engine off. 3. Remove the splash shield.
O Remove the six push pins. O Remove the six bolts and the splash
shield.
4. Place a large drain pan under the oil filter. filter 5. Loosen the oil filter by
wrench. Then remove the oil turning it by hand.
filter with an oil
6. Wipe the engine oil filter mounting sur-
face with a clean rag. Be sure to remove any old rubber gasket remaining on the mounting surface of the engine.
7. Coat the rubber gasket on the new filter
with engine oil.
Z X
8. Screw in the oil filter until a slight resis- tance is felt, then tighten an additional 2/3 turn.
9. Start the engine and check for leakage around the oil filter. Correct as required. 10.Turn the engine off and wait several minutes. Check the oil level. Add engine oil if necessary.
AUTOMATIC TRANSMISSION FLUID
WARNING
O When the engine is running, keep hands, jewelry and clothing away from any moving parts such as the cooling fan and drive belts.
O Automatic transmission fluid is poi- sonous and should be stored care- fully in marked containers out of the reach of children.
TEMPERATURE CONDITIONS FOR CHECKING O The fluid level should be checked using the HOT range on the dipstick after the following conditions have been met:
— The engine should be warmed up to
operating temperature.
— The vehicle should be driven at least 5
minutes.
— The ATF should be warmed to between
122 and 176°F (50 and 80°C).
ADI1067
O The ATF can be checked at fluid tem-
peratures of 86 to 122°F (30 to 50°C)
using the COLD range on the dipstick
after the engine is warmed up and before
driving. However,
the fluid should be
re-checked using the HOT range.
1. Park the vehicle on a level surface and
set the parking brake.
2. Start the engine and then move the se- lector lever through each gear range, ending in P (Park).
Maintenance and do-it-yourself 8-15
Z X
CAUTION
DO NOT OVERFILL. Use ONLY NIS- SAN Matic ‘D’ (Continental U.S. and Alaska) or Canada NISSAN Automatic Transmission Fluid. DexronTM III/ Mer- conTM or equivalent may also be used. Outside the continental United States and Alaska contact an autho- rized NISSAN dealership for more in- formation regarding suitable fluids, including recommended brand(s) of DexronTM automatic transmission fluid.
III/MerconTM
WDI0095
3. Check the fluid level with the engine
idling.
4. Remove the dipstick and wipe it clean
with lint-free paper.
5. Re-insert the dipstick into the charging
pipe as far as it will go.
6. Remove the dipstick and note the read- ing. If the level is on the low side of either range, add fluid through the charging pipe.
8-16 Maintenance and do-it-yourself
WDI0134
NOTE: If the vehicle has been driven for a long time at high speeds, or in city traffic in hot weather, or if it is being used to pull a trailer, the fluid level cannot be read accurately. You should wait until the fluid has cooled down (about 30 minutes).
Z X
POWER STEERING FLUID
BRAKE AND CLUTCH FLUID
ADI1120
ADI1118
ADI1119
The fluid level should be checked using the HOT MAX range on the power steering fluid reservoir at fluid temperatures of 122 to 176°F (50 to 80°C) or using the COLD MAX range on the power steering fluid reservoir at fluid temperatures of 32 to 86°F (0 to 30°C).
CAUTION
O Do not overfill. O Recommended fluid is Genuine
NISSAN PSF II or equivalent.
Check the brake fluid level in the reservoir. If
the fluid level is below the MIN line or the
brake warning light comes on, add DOT 3
fluid up to the MAX line.
Check the clutch fluid level in the reservoir
(manual transmission only). If the fluid level
is below the MIN line, add DOT 3 fluid up to
the MAX line.
If fluid must be added frequently, the system
should be thoroughly checked by an autho-
rized NISSAN dealer.
For further brake and clutch fluid specifica- tion information, refer to ‘‘Capacities and recommended fuel/lubricants’’ in the ‘‘Tech- nical and consumer information’’ section of this manual.
WARNING
Use only new fluid from a sealed con- tainer. Old, inferior or contaminated fluid may damage the brake and clutch systems. The use of improper fluids can affect the vehicle’s stopping ability.
Maintenance and do-it-yourself 8-17
Z X
WINDOW WASHER FLUID
CAUTION
Do not spill the fluid on any painted surfaces. This will damage the paint. If fluid is spilled, immediately wash the surface with water.
LDI0070
WINDOW WASHER FLUID RESERVOIR
CAUTION
O Do not substitute engine anti-freeze coolant for windshield washer solu- tion. This may result in damage to the paint.
O Do not fill the window washer reser- voir tank with washer fluid concen- trates at full strength. Some methyl alcohol based washer fluid concen- trates may permanently stain the
8-18 Maintenance and do-it-yourself
grille if spilled while filling the win- dow washer reservoir tank.
O Pre-mix washer fluid concentrates with water to the manufacturer’s rec- ommended levels before pouring the fluid into the window washer reser- voir tank. Do not use the window washer reservoir tank to mix the washer fluid concentrate and water.
For US Check the window washer fluid level in the reservoir tank and add fluid if necessary. Add a washer solvent to the water for better cleaning. In the winter season, add a wind- shield washer anti-freeze. Follow the manu- facturer’s instructions for the mixture ratio. For Canada Add fluid when the low washer fluid warning light comes on. Add windshield washer sol- vent to the water for better cleaning. In the winter season, add windshield washer anti- freeze.
Z X
BATTERY
Follow the manufacturer’s instructions for the mixture ratio. O Keep the battery surface clean and dry. Any corrosion should be washed off with a solution of baking soda and water.
O Make certain the terminal connections
are clean and securely tightened.
O If the vehicle is not to be used for 30 days or longer, disconnect the negative (−) bat- tery terminal cable to prevent discharge.
WARNING
O Do not expose the battery to flames or electrical sparks. Hydrogen gas generated by the battery is explo- sive. Do not allow battery fluid to contact your skin, eyes, fabrics, or painted surfaces. After touching a battery or battery cap, do not touch or rub your eyes. Thoroughly wash your hands. If the acid contacts your eyes, skin or clothing, immediately flush with water for at least 15 min- utes and seek medical attention.
O Do not operate the vehicle if the fluid in the battery is low. Low battery fluid can cause a higher load on the
battery which can generate heat, re- duce battery life, and in some cases lead to an explosion.
O When working on or near the battery, always wear suitable eye protection and remove all jewelry.
O Battery posts, terminals and related accessories contain lead and lead compounds. Wash hands after han- dling.
O Keep the battery out of the reach of
children.
ADI0709
1. Gently pry between the battery cap and
cover as illustrated to remove the cap. Use a cloth to protect the battery case.
2. Check the fluid level in each cell.
If it is necessary to add fluid, add only distilled water to bring the level up to the level indicator in each filler opening. Do not overfill. Vehicles operated in high temperatures or under severe conditions require fre- quent checks of the battery fluid level.
Maintenance and do-it-yourself 8-19
Z X
DRIVE BELTS
ADI0710
ADI1073
JUMP STARTING If jump starting is necessary, see ‘‘Jump starting’’ in the ‘‘In case of emergency’’ sec- tion. If the engine does not start by jump starting, the battery may have to be replaced. Contact an authorized NISSAN dealer.
WARNING
Be sure the ignition key is in the OFF or LOCK position. The engine could rotate unexpectedly.
1. Visually inspect each belt for signs of unusual wear, cuts, fraying or looseness. If the belt is in poor condition or loose, have it replaced or adjusted by an autho- rized NISSAN dealer.
2. Have the belts checked regularly for condi- tion and tension in accordance with the maintenance the ‘‘NISSAN Service and Maintenance Guide.’’
schedule
found
in
8-20 Maintenance and do-it-yourself
Z X
SPARK PLUGS
WARNING
Be sure the engine and ignition switch are off and that the parking brake is engaged securely.
CAUTION
Be sure to use the correct socket to remove the spark plugs. An incorrect socket can damage the spark plugs.
Maintenance and do-it-yourself 8-21
Z X
ADI1074
WDI0068
ADI1075
REPLACING SPARK PLUGS (except supercharger) Platinum-tipped spark plugs It is not necessary to replace platinum- tipped spark plugs as frequently as conven- tional type spark plugs because they last much longer. Follow the maintenance schedule, but do not reuse the spark plugs by cleaning or regapping. O Always replace spark plugs with rec-
commended or equivalent ones.
8-22 Maintenance and do-it-yourself
1. Disconnect the spark plug cables.
ADI1076
WDI0005
When disconnecting, always hold the boots — not the cables. Mark all cables to identify their original location. 2. Remove the spark plugs with a spark
plug socket.
3. Fit the new spark plugs, one at a time, into the spark plug socket and install them. Use only the specified spark plugs. Turn each plug several full turns by hand, then tighten with the spark plug socket to the correct torque. Do not over- tighten.
Z X
AIR CLEANER
Spark plug tightening torque:
14 to 22 ft-lb (20 to 29 Nzm)
4. Reconnect the spark plug cables to their
original positions.
REPLACING SPARK PLUGS (with supercharger) Please see your authorized NISSAN dealer for assistance.
ADI1079
WDI0097
The filter element should not be cleaned and reused as it is given a special treat- ment. We recommend it be replaced ac- cording to the maintenance intervals shown in the ‘‘NISSAN Service and Maintenance Guide.’’ When replacing the filter, wipe the inside of the air cleaner housing and the cover with a damp cloth.
WARNING
O Operating the engine with the air cleaner removed can cause you or others to be burned. The air cleaner not only cleans the air, it stops flame if the engine backfires. If it isn’t there and the engine backfires, you could be burned. Do not drive with the air cleaner removed, and be careful when working on the engine with the air cleaner removed.
Maintenance and do-it-yourself 8-23
Z X
O Never pour fuel into the throttle body or attempt to start the engine with the air cleaner removed. Doing so could result in serious injury.
8-24 Maintenance and do-it-yourself
Z X
WINDSHIELD WIPER BLADES
CAUTION
O After wiper blade replacement, return the wiper arm to its original position; otherwise it may be damaged when the hood is opened.
O Make sure the wiper blades contact the glass; otherwise the arms may be damaged from wind pressure.
O Worn windshield wiper blades can damage the windshield and impair driver vision.
CLEANING If your windshield is not clear after using the windshield washer or if a wiper blade chat- ters when running, wax or another material may be on the blade or windshield. Clean the outside of the windshield with a washer solution or a mild detergent. Your windshield is clean if beads do not form when rinsing with clear water. Clean the blade by wiping it with a cloth soaked in a washer solution or a mild deter- gent. Then rinse the blade with clear water. If your windshield is still not clear after
WDI0098
cleaning the blades and using the wiper, replace the blades. REPLACING Replace the wiper blades if they are worn. 1. Lift the wiper arm away from the wind-
shield.
2. Push the release tab,
then move the wiper blade down the wiper arm to re- move.
3. Remove the wiper blade. 4. Insert the new wiper blade onto the wiper
arm until it clicks into place.
Maintenance and do-it-yourself 8-25
Z X
Rear window wiper blade 1. Lift the wiper arm away from the wind-
shield.
2. Push the wiper blade in and pivot until
the blade becomes free.
3. Insert a new blade onto the wiper arm
and snap into place.
8-26 Maintenance and do-it-yourself
WDI0105
Z X
PARKING BRAKE AND BRAKE PEDAL
WDI0071
If you wax the surface of the hood, be careful not to let wax get into the washer nozzle. This may cause clogging or im- proper windshield washer operation. If wax gets into the nozzle, remove it with a needle or small pin.
LDI0099
DI0453
CHECKING PARKING BRAKE From the released position, firmly push the parking brake down. If the number of clicks is out of the range listed above, see an authorized NISSAN dealer.
CHECKING BRAKE PEDAL With the engine running, check distance A between the upper surface of the pedal and the metal floor. Distance A:
Manual Transmission
Automatic Transmission
Four Wheel ABS
4 in. (100mm)
4 1/4 in. (110mm)
If it is out of the range shown above, see an authorized NISSAN dealer.
Maintenance and do-it-yourself 8-27
Z X
Self-adjusting brakes Your vehicle is equipped with self-adjusting brakes. The front disc-type brakes self-adjust every time the brake pedal is applied. The rear drum-type brakes on two-wheel drive trucks self-adjust every time the parking brake is applied. The rear drum-type brakes on four- wheel drive trucks self-adjust every time the brake pedal is applied. If the brake pedal goes down farther than normal, it may be due to a lack of adjustment of the rear drum brakes. Apply the parking brake several times.
WARNING
If the brake pedal height does not re- turn to normal, see an authorized NIS- SAN dealer and have it checked.
Brake pad wear indicators The disc brake pads on your vehicle have audible wear indicators. When a brake pad requires replacement, it will make a high pitched scraping or screeching sound when the vehicle is in motion whether or not the brake pedal is depressed. Have the brakes 8-28 Maintenance and do-it-yourself
checked as soon as possible if the wear indicator sound is heard. Under some driving or climate conditions, occasional brake squeak, squeal or other noise may be heard. Occasional brake noise during light to moderate stops is nor- mal and does not affect the function or performance of the brake system. The rear drum brakes (if so equipped) do not have audible wear indicators. Should you ever hear an unusually loud noise from the rear drum brakes, have them inspected as soon as possible by an authorized NIS- SAN dealer. Proper brake inspection intervals should be followed. For more information regard- ing brake inspections, see the appropriate maintenance schedule information in the ‘‘NISSAN Service and Maintenance Guide.’’ BRAKE BOOSTER Check the brake booster function with the following steps: 1. With the engine off, press and release times. When the brake pedal several brake pedal movement (distance of travel) remains the same from one pedal
application to the next, continue on to next step.
2. While depressing the brake pedal, start the engine. The pedal height should drop a little.
3. With the brake pedal depressed, stop the engine. Keeping the pedal depressed for about 30 seconds, the pedal height should not change.
4. Run the engine for one minute without depressing the brake pedal, then turn it off. Depress the brake pedal several times. The pedal travel distance will de- crease gradually with each depression as the vacuum is released from the booster.
If the brakes do not operate properly, have the brakes checked by an authorized NISSAN dealer.
Z X
CLUTCH PEDAL
ADI0528
CHECKING CLUTCH PEDAL Press the pedal by hand and be sure the free travel is within the above limit. If free travel is out of the range shown above, see an authorized NISSAN dealer.
Maintenance and do-it-yourself 8-29
Z X
FUSES
ADI1128
PASSENGER COMPARTMENT
CAUTION
Never use a fuse of a higher amperage rating than specified on the fuse box cover. This could damage the electrical system or cause a fire.
3. Remove the fuse with the fuse puller. 4. If the fuse is open, replace it with a new
fuse.
5. If a new fuse opens again, have the electrical system checked and repaired by an authorized NISSAN dealer.
If the electrical equipment does not operate, check for an open fuse. 1. Be sure the ignition key and the headlight
switch are OFF.
2. Remove the fuse box cover.
8-30 Maintenance and do-it-yourself
Z X
KEYFOB BATTERY REPLACEMENT
Replace the battery in the keyfob as follows:
1. Open the lid using a coin.
2. Replace the battery with a new one.
Recommended battery: Toshiba CR2025
or equivalent.
3. Close the lid securely.
4. Press the LOCK button, then the UNLOCK button two or three times to check the keyfob operation.
If the battery is removed for any reason
other than replacement, perform step 4
above.
O An improperly disposed battery can
hurt the environment. Always confirm
local regulations for battery disposal.
O The keyfob is water-resistant; how-
ever, if it does get wet, immediately
wipe completely dry.
O The operational range of the keyfob extends to approximately 33 ft (10 m) from the vehicle. This range may vary with conditions.
Maintenance and do-it-yourself 8-31
Z X
LPD0081
LIGHTS
FCC Notice: Changes or modifications not expressly approved by the manufacturer for com- pliance could void the user’s authority to operate the equipment. This device complies with part 15 of the FCC Rules and RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference re- ceived including interference that may cause undesired operation of the device.
LDI0101
HEADLIGHTS The headlight is a semi-sealed beam type which uses a replaceable headlight (halo- gen) bulb.
8-32 Maintenance and do-it-yourself
CAUTION
O High pressure halogen gas is sealed inside the halogen bulb. The bulb may break if the glass envelope is scratched or the bulb is dropped.
O When handling the bulb, do not
touch the glass envelope.
Replacing the headlight bulb 1. Open the engine hood. 2. Disconnect
the negative (2) battery
cable.
3. Disconnect the electrical connector from
the rear end of the bulb.
4. Turn the bulb retaining ring counterclock- it is free from the headlight
wise until reflector and then remove it.
5. Carefully remove the headlight bulb. Do not shake or rotate the bulb when removing it. 6. Install the new bulb in the reverse order
of removal.
O Be sure the lip of the bulb socket
contacts the headlight body.
DO NOT TOUCH THE BULB.
Z X
O Use the same number and wattage
CAUTION
as originally installed:
Wattage 65/55
Bulb No. HB5/9007*
*: Always check with the Parts Depart- ment at an authorized NISSAN dealer for the latest parts information.
O Aiming is not necessary after replac-
ing the bulb.
O Do not leave the bulb out of the headlight reflector for a long period of time as dust, moisture, and smoke may enter the headlight body and affect the performance of the head- light.
O When aiming adjustment
is neces- sary, contact an authorized NISSAN dealer.
WDI0102
FOG LIGHTS (if so equipped) Replacing the fog light bulb
CAUTION
O High pressure halogen gas is sealed inside the halogen bulb. The bulb may break if the glass envelope is scratched or the bulb is dropped.
O When handling the bulb, do not
touch the glass envelope.
Maintenance and do-it-yourself 8-33
LDI0028
Z X
1. Unclip the two metal clips on the side of
the fog light.
2. Pull out and support the fog light assem-
bly.
3. Disconnect the fog light bulb connector. 4. Lift the spring retainer. 5. Remove the fog light bulb. O The fog light bulb can not be separated from the wire and is serviced as an assembly.
6. Install the new bulb in the reverse order of removal. DO NOT TOUCH THE BULB.
EXTERIOR AND INTERIOR LIGHTS
Item
Wattage (W)
Headlight
Turn signal light
Parking light
Side Marker
Rear combination light:
Turn signal
Stop/Tail
Back-up
License plate light
Fog light
Dome light
Map light without compass
Map light with compass
High-mounted stop light
65/55
28/8
27
27/7
16
3.8
55
3.8
12.8
Bulb No.*1
9007
3457AK*2
168*2
168
3157Ak
3057k
921
168
H3
82
82
168
912
*1: Always check with the Parts Department at an authorized NISSAN dealer for the latest parts information. *2 The bulb is not serviceable in-vehicle. See an authorize NISSAN dealer for assistance.
8-34 Maintenance and do-it-yourself
Z X
ADI1131
Replacement procedures All other lights are either type A, B, C or D. When replacing a bulb, first remove the lens and/or cover.
Maintenance and do-it-yourself 8-35
Z X
8-36 Maintenance and do-it-yourself
WDI0103
Z X
WHEELS AND TIRES
DI0047
If you have a flat tire, see the ‘‘In case of emergency’’ section of this manual. TIRE PRESSURE Maximum inflation pressure Do not exceed the maximum inflation pres- sures shown on the side wall of the tire. Tire inflation pressure Check the tire pressure (including the spare) at least once a month and always prior to long distance trips. Tire pressure should be checked when tires are COLD. COLD tire pressures are shown on the tire
placard affixed to the inside of the glove box lid. Incorrect tire pressure may adversely affect tire life and vehicle handling. COLD pressure:
After vehicle has been parked for three hours or more or driven less than 1 mile (1.6 km) at moderate speeds.
WARNING
O Improperly inflated tires can fail sud-
denly and cause an accident
O The vehicle weight capacity is indi- cated on the F.M.V.S.S. certification label. Do not load your vehicle be- yond this capacity. Overloading your vehicle may result in reduced tire life, unsafe operating conditions due to premature tire failure, or unfavorable handling characteristics and could also lead to a serious accident. Load- ing beyond the specified capacity may also result in failure of other vehicle components.
O Before taking a long trip, or whenever you have loaded your vehicle heavily, use a tire pressure gauge to ensure that the tire pressure is at the speci- fied level.
O Do not drive your vehicle over 85
MPH (137 km/h) unless it is equipped
with high speed rated tires. Driving
faster than 85 MPH (137 km/h) may
result in tire failure, loss of control
and possible injury.
O For additional information regarding tires, refer to ‘‘Important Tire Safety Information’’ in the Warranty Infor- mation Booklet (US) or ‘‘Tire Safety Information’’ in the Warranty and Roadside Assistance information booklet (Canada).
Maintenance and do-it-yourself 8-37
Z X
TYPES OF TIRES
WARNING
When changing or replacing tires, be sure all four tires are of the same type (i.e., Summer, All Season or Snow) and construction. An authorized NISSAN dealer may be able to help you with information about tire type, size, speed rating and availability. Replacement tires may have a lower speed rating than the factory equipped tires, and may not match the potential maximum vehicle speed. Never exceed the maxi- mum speed rating of the tire. O For additional information regarding tires, refer to ‘‘Important Tire Safety Information’’ in the Warranty Infor- mation Booklet (US) or ‘‘Tire Safety Information’’ in the Warranty and Roadside Assistance information booklet (Canada).
All season tires NISSAN specifies All Season tires on some models to provide good performance for use all year around, including snowy and icy road conditions. All Season Tires are iden- 8-38 Maintenance and do-it-yourself
tified by ‘‘ALL SEASON’’ and/or ‘‘M&S’’ on the tire sidewall. Snow tires have better snow traction than All Season tires and may be more appropriate in some areas. Summer tires NISSAN specifies summer tires on some models to provide superior performance on dry roads. Summer tire performance in snow and ice will be substantially reduced. Summer tires do not have the tire traction rating ‘‘M&S’’ on the tire sidewall. If you plan to operate your vehicle in snowy or icy conditions, NISSAN recommends the use of ‘‘SNOW’’ or ‘‘ALL SEASON’’ tires on all four wheels. Snow tires If snow tires are needed, it is necessary to select tires equivalent in size and load rating to the original equipment tires. If you do not, it can adversely affect the safety and han- dling of your vehicle. If you install snow tires, they must be the same size, brand, construction and tread pattern on all four wheels. Generally, snow tires will have lower speed ratings than factory equipped tires and may
not match the potential maximum vehicle speed. Never exceed the maximum speed rating of the tire. For additional traction on icy roads, studded tires may be used. However, some U.S. States and Canadian provinces prohibit their use. Check local, state and provincial laws before installing studded tires. Skid and traction capabilities of studded snow tires on wet or dry surfaces may be poorer than that of non-studded snow tires. TIRE CHAINS Use of tire chains may be prohibited accord- ing to location. Check the local laws before installing tire chains. When installing tire chains, make sure they are the proper size for the tires on your vehicle and are installed according to the chain manufacturer’s sug- gestions. Use only SAE class ‘‘S’’ chains. Other types may damage your vehicle. Use chain tensioners when recommended by the tire chain manufacturer to ensure a tight fit. Loose end links of the tire chain must be secured or removed to prevent the possibil- ity of whipping action damage to the fenders or undercarriage. If possible, avoid fully loading your vehicle when using tire chains. In addition, drive at a reduced speed. Oth-
Z X
erwise, your vehicle may be damaged and/or vehicle handling and performance may be adversely affected. Never install tire chains on a TEMPORARY USE ONLY spare tire. Tire chains must be installed only on the rear wheels and not on the front wheels. Do not use tire chains on dry roads. Driving with chains in such conditions can cause damage to the various mechanisms of the vehicle due to some overstress. When driv- ing on clear paved roads, be sure to change to 2WD.
ADI1115
CHANGING WHEELS AND TIRES Tire rotation NISSAN recommends rotating the tires ev- ery 7,500 miles (12,000 km). See ‘‘Flat tire’’ in the ‘‘In case of emergency’’ section for tire replacing procedures.
Wheel nut tightening torque:
98 ft-lb (133 Nzm)
WARNING
O After rotating the tires, check and
adjust the tire pressure.
O Retighten the wheel nuts when the vehicle has been driven for 600 miles (1,000 km) (also in cases of a flat tire, etc.).
O Do not include the spare tire in the
tire rotation.
O For additional information regarding tires, refer to ‘‘Important Tire Safety Information’’ in the Warranty Infor- mation Booklet (US) or ‘‘Tire Safety Information’’ in the Warranty and Roadside Assistance information booklet (Canada).
Maintenance and do-it-yourself 8-39
Z X
O Improper service of the spare tire may result in serious personal in- jury. If it is necessary to repair the spare tire, contact an authorized NISSAN dealer.
O For additional information regarding tires, refer to ‘‘Important Tire Safety Information’’ in the Warranty Infor- mation Booklet (US) or ‘‘Tire Safety Information’’ in the Warranty and Roadside Assistance information booklet (Canada).
Replacing tires and wheels When replacing a tire, use the same size, tread design, speed rating and load carrying capacity as originally equipped. Recom- mended types and sizes are shown in ‘‘Wheel/tire size’’ in the ‘‘Technical and con- sumer information’’ section of this manual.
WARNING
O The use of tires other than those recommended or the mixed use of tires of different brands, construction (bias, bias-belted or radial), or tread patterns can adversely affect the ride,
MDI0004
Tire wear and damage
WARNING
O Tires should be periodically in- spected for wear, cracking, bulging or objects caught in the tread. If excessive wear, cracks, bulging or deep cuts are found, the tire(s) should be replaced.
O The original
tires have a built-in tread wear indicator. When the wear indicators are visible, the tire(s) should be replaced.
8-40 Maintenance and do-it-yourself
braking, handling, ground clearance, body-to-tire clearance, tire chain clear- ance, speedometer calibration, head- light aim and bumper height. Some of these effects may lead to accidents and could result in serious personal injury. O If the wheels are changed for any reason, always replace with wheels which have the same offset dimen- sion. Wheels of a different offset could cause premature tire wear, de- grade vehicle handling characteris- tics and/or interference with the brake discs/drums. Such interfer- ence can lead to decreased braking efficiency brake pad/shoe wear. Refer to “Wheel/tire size” in the “Technical and con- sumer information” section of this manual for wheel off-set dimen- sions.
and/or
early
O Do not install a deformed wheel or tire even if it has been repaired. Such wheels or tires could have unknown structural damage and could fail without warning.
Z X
O The use of retread tires is not recom-
mended.
O For additional information regarding tires, refer to ‘‘Important Tire Safety Information’’ in the Warranty Infor- mation Booklet (US) or ‘‘Tire Safety Information’’ in the Warranty and Roadside Assistance information booklet (Canada).
Four-wheel drive models
CAUTION
Always use tires of the same type, size, brand, construction (bias, bias-belted or radial), and tread pattern on all four wheels. Failure to do so may result in a circumference difference between tires on the front and rear axles which will cause excessive tire wear and may damage the transmission, transfer case and differential gears.
If excessive tire wear is found, it is recom- mended that all four tires be replaced with tires of the same size, brand, construction and tread pattern. The tire pressure and wheel alignment should also be checked and corrected as necessary. Contact an authorized NISSAN dealer. Wheel balance Unbalanced wheels may affect vehicle han- dling and tire life. Even with regular use, wheels can get out of balance. Therefore, they should be balanced as required. Wheel balance service should be performed with the wheels off the vehicle. Spin balanc-
ing the front wheels on the vehicle could lead to transmission damage. O For additional information regarding tires, refer to ‘‘Important Tire Safety Informa- tion’’ in the Warranty Information Booklet (US) or ‘‘Tire Safety Information’’ in the Warranty and Roadside Assistance infor- mation booklet (Canada).
Care of wheels O Wash the wheels when washing the ve-
hicle to maintain their appearance.
O Clean the inner side of the wheels when the wheel is changed or the underside of the vehicle is washed.
O Do not use abrasive cleaners when
washing the wheels.
O Inspect wheel rims regularly for dents or corrosion. This may cause loss of pres- sure or damage the tire bead.
O NISSAN recommends waxing the road in
wheels to protect against road salt areas where it is used during winter.
Maintenance and do-it-yourself 8-41
Z X
MEMO
8-42 Maintenance and do-it-yourself
Z X
9 Technical and consumer information
Capacities and recommended fuel/lubricants........9-2
Fuel recommendation
(except supercharger) .......................................9-4
Engine oil and oil filter recommendation...........9-6
Recommended SAE viscosity number..............9-7
Air conditioner system refrigerant and
lubricant recommendations ...............................9-8
Specifications .........................................................9-9
Engine ...............................................................9-9
Wheels and tires..............................................9-10
Dimensions and weights .................................9-11
When traveling or registering your vehicle in
another country ....................................................9-12
Vehicle identification.............................................9-12
Vehicle identification number (VIN) plate........9-12
Vehicle identification number
(chassis number).............................................9-12
Engine serial number ......................................9-13
F.M.V.S.S. certification label............................9-13
Emission control information label ..................9-14
Tire placard......................................................9-14
Air conditioner specification label....................9-14
Installing front license plate..................................9-15
Vehicle loading information ..................................9-15
Terms...............................................................9-15
Determining vehicle payload capacity.............9-16
Securing the load ............................................9-16
Loading tips .....................................................9-17
Payload weight capacity..................................9-18
Measurement of weights .................................9-19
Towing a trailer.....................................................9-19
Maximum load limits........................................9-19
Towing load/specification chart .......................9-21
Towing safety...................................................9-22
Trailer tow harness and module
(if so equipped)................................................9-23
Uniform tire quality grading..................................9-25
Emission control system warranty .......................9-26
Reporting safety defects (US only)......................9-27
Readiness for inspection/maintenance (I/M)
test (US only) .......................................................9-27
Owner manual/service manual order
information............................................................9-29
In the event of a collision ................................9-30
Z X
CAPACITIES AND RECOMMENDED FUEL/ LUBRICANTS
The following are approximate capacities. The actual refill capacities may be a little different. When refilling, follow the procedure described in the ‘‘Maintenance and do-it-yourself’’ section to determine the proper refill capacity.
Capacity (Approximate)
Fuel without supercharger
with supercharger
Engine oil
Drain and Refill
KA24DE
VG33E/VG33ER
With oil filter
Without oil filter
With oil filter Without oil filter
Cooling system (with heater and reservoir tank)
KA24DE
M/T
4X2
VG33E/ VG33ER A/T & M/T
US
measure
19-3/8 gal
19-3/8 gal
3-3/4 qt
3-1/2 qt
3-1/2 qt 3-1/8 qt
7-3/4 qt
11-5/8 qt
Imp
measure
16-1/8 gal
16-1/8 gal
3-1/8 qt
2-7/8 qt
2-7/8 qt 2-5/8 qt
6-3/8
9-5/8 qt
Liter
73.4
73.4
3.5
3.3
3.3
3.0
7.3
10.95
Recommended Fluids & Lubricants
Unleaded gasoline with an octane rating of
at least 87 AKI (RON 91)*1
Unleaded gasoline with an octane rating of
at least 91 AKI (RON 96)*1
O API Certification Mark *2
O API grade SG/SH, Energy Conserving I &
II or API grade SJ, Energy Conserving *2
O ILSAC grade GF-I & II
50% Genuine NISSAN Anti-freeze coolant
or equivalent
50% Demineralized or Distilled water
*1: For further details, see ‘‘Fuel recommendation’’.
*2: For further details, see ‘‘Recommended SAE engine oil viscosity’’.
9-2 Technical and consumer information
Z X
Manual transmission gear oil
Final drive gear oil
Transfer fluid
Automatic transmission fluid