Download PDF Manual


O Adjust the antenna standing-wave ratio as recommended by the manu- facturer.


O Connect the ground wire from the


CB radio chassis to the body.


O For details, consult an authorized


NISSAN dealer.


Z X


5 Starting and driving


Precautions when starting and driving...................5-2
Exhaust gas (carbon monoxide) .......................5-2
Three-way catalyst ............................................5-3
On-pavement and off-road driving precautions ........................................................5-3
Avoiding collision and rollover...........................5-3
Drinking alcohol/drugs and driving....................5-4
Driving safety precautions.................................5-4
Ignition switch.........................................................5-6
Automatic transmission .....................................5-6
Manual transmission..........................................5-7
Key positions .....................................................5-7
Before starting the engine......................................5-8
Starting the engine.................................................5-8
Driving the vehicle..................................................5-9
Automatic transmission (if so equipped)...........5-9
Manual transmission........................................5-13
Parking brake .......................................................5-14
Cruise control (if so equipped).............................5-15
Precautions on cruise control..........................5-15
Cruise control operations ................................5-16


Break-in schedule ................................................5-17
Increasing fuel economy ......................................5-17
Using four-wheel drive .........................................5-18
........................5-18
Transfer case shifting procedures...................5-18
Auto-lock free-running hubs ............................5-19
Parking/parking on hills........................................5-22
Power steering .....................................................5-23
Brake system........................................................5-23
Braking precautions.........................................5-23
Anti-lock brake system (ABS) .........................5-24
Cold weather driving ............................................5-25
Freeing a frozen door lock ..............................5-25
Anti-freeze .......................................................5-25
Battery .............................................................5-25
Draining of coolant water ................................5-25
Tire equipment.................................................5-26
Special winter equipment ................................5-26
Driving on snow or ice.....................................5-26
Engine block heater (if so equipped) ..............5-27


Z X


PRECAUTIONS WHEN STARTING AND DRIVING


WARNING


O Do not


leave children, unreliable adults, or pets alone in your vehicle. They could accidentally injure them- selves or others through inadvertent operation of the vehicle. Also, on hot, sunny days, temperatures in a closed vehicle could quickly become high enough to cause severe or pos- sibly fatal injuries to people or ani- mals.


O Properly secure all cargo to help prevent it from sliding or shifting. Do not place cargo higher than the seat- backs. In a sudden stop or collision, unsecured cargo could cause per- sonal injury.


EXHAUST GAS (carbon monoxide)


WARNING


O Do not breathe exhaust gases; they contain colorless and odorless car- bon monoxide. Carbon monoxide is a dangerous. It can cause uncon- sciousness or death.


5-2 Starting and driving


O If you suspect that exhaust fumes are entering the vehicle, drive with all windows fully open, and have the vehicle inspected immediately.


O Do not run the engine in closed


spaces such as a garage.


O Do not park the vehicle with the engine running for any extended length of time.


O Keep the back door and rear win- dows closed while driving, other- wise exhaust gases could be drawn into the passenger compartment. If you must drive with the back door or rear windows open, follow these pre- cautions: 1. Open all the windows. 2. Set the air recirculation switch OFF and the fan control at 4 (high) to circulate the air.


O If electrical wiring or other cable connections must pass to a trailer through the seal on the back door or the body, follow the manufacturer’s recommendation to prevent carbon monoxide entry into the vehicle.


O If a special body, camper, or other equipment is added for recreational or other usage, follow the manufac- turer’s recommendation to prevent carbon monoxide entry into the ve- hicle. Do not occupy these areas while the engine is running even if the vehicle is parked. Some recreational vehicle appliances such as stoves, refrigerators, heaters, etc. may also generate carbon monoxide.


O The exhaust system and body should be inspected by a qualified mechanic whenever: a. The vehicle is raised for service. b. You suspect that exhaust fumes are entering into the passenger compartment.


c. You notice a change in the sound


of the exhaust system.


d. You have had an accident involv- ing damage to the exhaust system, underbody, or rear of the vehicle.


Z X


THREE-WAY CATALYST The three-way catalyst is an emission control device installed in the exhaust system. Ex- haust gases in the converter are burned at high temperatures to help reduce pollutants.


WARNING


O The exhaust gas and the exhaust system are very hot. Keep people, animals or flammable materials away from the exhaust system com- ponents.


O Do not stop or park the vehicle over flammable materials such as dry grass, waste paper or rags. They may ignite and cause a fire.


CAUTION


O Do not use leaded gasoline. Depos- its from leaded gasoline will seri- ously reduce the three-way cata- lyst’s ability to help reduce exhaust pollutants.


O Keep your engine tuned up. Malfunc- tions in the ignition, fuel injection, or electrical systems can cause over-


rich fuel flow into the three-way cata- lyst, causing it to overheat. Do not keep driving if the engine misfires, or if noticeable loss of performance or other unusual operating condi- tions are detected. Have the vehicle inspected promptly by an authorized NISSAN dealer.


O Avoid driving with an extremely low fuel level. Running out of fuel could cause the engine to misfire, damag- ing the three-way catalyst.


O Do not race the engine while warm-


ing it up.


O Do not push or tow your vehicle to


start the engine.


ON-PAVEMENT AND OFF-ROAD DRIVING PRECAUTIONS Utility vehicles have a significantly higher rollover rate than other types of vehicles. They have higher ground clearance than passenger cars to make them capable of performing in a variety of on-pavement and off-road applications. This gives them a


higher center of gravity than ordinary cars. An advantage of higher ground clearance is a better view of the road, allowing you to anticipate problems. However, they are not designed for cornering at the same speeds as conventional two-wheel drive vehicles any more than low-slung sports cars are designed to perform satisfactorily under off-road conditions. If at all possible, avoid sharp turns or abrupt maneuvers particu- larly at high speeds. As with other vehicles of this type, failure to operate this vehicle correctly may result in loss of control or vehicle rollover. Be sure to read the driving safety precau- tions later in this section. AVOIDING COLLISION AND ROLLOVER


WARNING


Failure to operate this vehicle in a safe and prudent manner may result in loss of control or an accident.


Be alert and drive defensively at all times. Obey all traffic regulations. Avoid excessive speed, high speed cornering, or sudden steering maneuvers, because these driving Starting and driving 5-3


Z X


practices could cause you to lose control of your vehicle. As with any vehicle, a loss of control could result in a collision with other vehicles or objects, or cause the vehicle to rollover, particularly if the loss of control causes the vehicle to slide sideways. Be attentive at all times, and avoid driving when tired. Never drive when under the influence of alcohol or drugs (including prescription or over-the-counter drugs which may cause drowsiness). Al- ways wear your seat belt as outlined in the ‘‘Seats, restraints and supplemental air bag systems’’ section of this manual, and in- struct your passengers to do so. Seat belts help reduce the risk of injury in collisions and rollovers. In a rollover crash, an unbelted person is significantly more likely to die than a person wearing a seat belt. DRINKING ALCOHOL/DRUGS AND DRIVING


WARNING


Never drive under the influence of alco- hol or drugs. Alcohol in the blood- stream reduces coordination, delays


5-4 Starting and driving


reaction time and impairs judgement. Driving after drinking alcohol increases the likelihood of being involved in an accident injuring yourself and others. Additionally, if you are injured in the accident, alcohol can increase the se- verity of injury.


Nissan is committed to safe driving. But, you must choose not to drive under the influence of alcohol. Every year thousands of people are injured or killed in alcohol related accidents. Although the local laws vary on what is considered to be legally intoxicated, the fact is that alcohol affects all people differently and most people underes- timate the effects of alcohol. Remember, drinking and driving don’t mix! And that’s true for drugs too (over the counter, prescription, and illegal drugs). Don’t drive if your ability to operate your vehicle is impaired by alcohol, drugs, or some other physical condition. DRIVING SAFETY PRECAUTIONS Your NISSAN is designed for both normal and off-road use. However, avoid driving in


deep water or mud as your NISSAN is mainly designed for leisure use, unlike a conventional offroad vehicle. Remember that two-wheel drive models are less capable than four-wheel drive models for rough road driving and extrication when stuck in deep snow or mud, or the like. Please observe the following precautions:


WARNING


O Drive carefully when off the road and avoid dangerous areas. Every person who drives or rides in this vehicle should be seated with their seat belt fastened. This will keep you and your passengers in position when driving over rough terrain.


O Do not drive across steep slopes. In- stead drive either straight up or straight down the slopes. Off-road ve- hicles can tip over sideways much more easily than they can forward or backward.


Z X


O Many hills are too steep for any ve- hicle. If you drive up them, you may stall. If you drive down them, you may not be able to control your speed. If you drive across them, you may roll over.


O Do not shift gears while driving on downhill grades as this could cause loss of control of the vehicle.


O Stay alert when driving to the top of a hill. At the top there could be a drop-off or other hazard that could cause an accident.


O If your engine stalls or you cannot make it to the top of a steep hill, never attempt to turn around. Your vehicle could tip or roll over. Always back straight down in R (Reverse) gear. Never back down in N (Neutral) or with the clutch depressed (manual transmission vehicles), us- ing only the brake, as this could cause loss of control.


O Heavy braking going down a hill- could cause your brakes to over heat


and fade, resulting in loss of control and an accident. Apply brakes lightly and use a low gear to control your speed.


O Unsecured cargo can be thrown around when driving over rough ter- rain. Properly secure all cargo so it will not be thrown forward and cause injury to you or your passengers.


O To avoid raising the center of gravity excessively, do not exceed the rated capactiy of the roof rack/gear bin (if so equipped) and evenly distribute the load. Secure heavy loads in the cargo area as far forward and as low as possible. Do not equip the vehicle with tires larger than specified in this manual. This could cause your ve- hicle to roll over.


O Do not grip the inside or spokes of the steering wheel when driving offroad. The steering wheel could move suddenly and injure your hands. Instead drive with your fin- gers and thumbs on the outside of the rim.


O Before operating the vehicle, ensure that the driver and all passengers have their seat belts fastened.


O Always drive with the floor mats in place as the floor may become hot. O Lower your speed when encoutering strong crosswinds. With a higher center of gravity, your NISSAN is more affected by strong side winds. Slower speeds ensure better vehicle control.


O Do not drive beyond the perfor- mance of the tires, even with 4WD engaged.


O Accelerating quickly, sharp steering maneuvers or sudden braking may cause loss of control.


O If at all possible, avoid sharp turning maneuvers, particularly at high speeds. Your NISSAN four wheel drive vehicle has a higher center of gravity than a two-wheel drive ve- hicle. The vehicle is not designed for cornering at the same speeds as conventional two-wheel drive ve- hicles. Failure to operate this vehicle


Starting and driving 5-5


Z X


correctly could result in loss of con- trol and/or a rollover accident.


O Always use tires of the same type, size, brand, construction (bias, bias belted or radial), and tread pattern on all four wheels. Install tire chains on the rear wheels when driving on slippery roads and drive carefully.


O Be sure to check the brakes immedi- ately after driving in mud or water. See ‘‘Brake system’’ later in this sec- tion for ‘‘Wet brakes’’.


O Avoid parking your vehicle on steep hills. If you get out of the vehicle and it rolls forward, backward or side- ways, you could be injured.


O Whenever


you


drive


off-road through sand, mud or water as deep as the wheel hub, more frequent maintenance may be required. See the ‘‘Periodic maintenance’’ ‘‘Maintenance’’ section this manual.


in of


5-6 Starting and driving


IGNITION SWITCH


ASD1014


AUTOMATIC TRANSMISSION On automatic transmission models, the ig- nition lock is designed so the key cannot be turned to LOCK and removed until the shift selector lever is moved to the P (Park) position. When removing the key from the ignition, make sure the shift selector lever is in the P (Park) position. If the key cannot be turned to the LOCK position, proceed as follows to remove the key: 1) Move the shift selector lever into the P


(Park) position.


2) Turn the ignition key slightly in the ON


direction.


3) Turn the key toward the LOCK position. 4) Remove the key. The shift lever is designed so it cannot be moved out of P (Park) and into any of the other gear positions if the ignition key is turned to OFF or if the key is removed from the switch. The shift lever can be moved if the igni- tion switch is in the ACC position. This allows the vehicle to be moved if the battery is discharged. The shift lever can also be moved if the ignition switch is in the ON position and the foot brake pedal is depressed. There is an OFF position between the LOCK and ACC positions. The OFF posi- tion is indicated by a (1( on the key cylinder. When the ignition is in the OFF position, is not locked.


the steering wheel


Z X


In order for the steering wheel to be locked, it must be turned about 1/8 of a turn clock- wise from the straight up position. To lock the steering wheel, turn the key to the LOCK position. Remove the key. To unlock the steering wheel, insert the key and turn it gently while rotating the steering wheel slightly right and left.


WARNING


Never remove or turn the key to the LOCK position while driving. The steer- ing wheel will lock. This may cause the driver to lose control of the vehicle and could result in serious vehicle damage or personal injury.


ASD1015


MANUAL TRANSMISSION The ignition switch includes an anti-theft steering lock device. The key can only be removed when the ignition switch is in the LOCK position. On manual transmission models, to turn the ignition key to LOCK from ACC or ON, turn the key to OFF, push the key in, then turn the key to LOCK. In order for the steering wheel to be locked, it must be turned about 1/8 of a turn clock- wise from the straight up position.


To lock the steering wheel, turn the key to the LOCK position. Remove the key. To unlock the steering wheel, insert the key and turn it gently while rotating the steering wheel slightly right and left.


WARNING


Never remove or turn the key to the LOCK position while driving. The steer- ing wheel will lock. This may cause the driver to lose control of the vehicle and could result in serious vehicle damage or personal injury.


KEY POSITIONS LOCK Normal parking position (0) OFF (Manual transmission model) (1) The engine can be turned off without locking the steering wheel. ACC (Accessories) (2) This position activates electrical accesso- ries such as the radio when the engine is not running. The shifter can be moved if the ignition switch is in ACC position.


Starting and driving 5-7


Z X


ON (Normal operating position) (3) This position turns on the ignition system and electrical accessories. START (4) This position starts the engine. As soon as the engine has started, release the key. It automatically returns to the ON position.


BEFORE STARTING THE ENGINE O Make sure the area around the vehicle is


clear.


O Check fluid levels such as engine oil, coolant, brake and clutch fluid, and win- dow washer fluid as frequently as pos- sible, at least whenever you refuel.


O Check that all windows and lights are


clean.


O Visually inspect tires for their appearance and condition. Also check tires for proper inflation.


O Lock all doors. O Position seat and adjust head restraints. O Adjust inside and outside mirrors. O Fasten seat belts and ask all passengers


to do likewise.


O Check the operation of warning lights when key is turned to the ON (3) position. See and chimes9 in the 9Instruments and controls9
section.


9Warning/Indicator


lights


5-8 Starting and driving


STARTING THE ENGINE


1. Apply the parking brake. 2. Automatic transmission:


Move the selector lever to P (Park) or N (Neutral). P (Park) is preferred. The shift lever cannot be moved out of P (Park) and into any of the other gear positions if the ignition key is turned to OFF or if the key is removed from the ignition switch. The starter is designed not to operate if the selector lever is in one of the driving positions. Manual transmission: Move the gearshift lever to N (Neutral), and fully depress the clutch pedal to the floor while starting the engine. The starter is designed not to operate unless the clutch pedal is fully de- pressed.


3. With your foot off


the accelerator pedal, turn the ignition key to START. Release the key when the engine starts. If the engine starts, but fails to run, repeat the above procedure.


Z X


O If the engine is very hard to start in extremely cold or hot weather, depress the accelerator pedal fully and hold it to help start the engine.


O In the summer, when restarting the engine within 30 minutes after it has been stopped, keep the accelerator pedal fully depressed while starting.


CAUTION


Do not operate the starter for more than 15 seconds at a time. If the engine does not start, turn the key off and wait 10
seconds before cranking again, other- wise the starter could be damaged.


4. Warm-up


Always allow the engine to idle for at least 30 seconds after starting. Drive at a moderate speed for a short distance first, especially in cold weather.


DRIVING THE VEHICLE


AUTOMATIC TRANSMISSION (if so equipped)


WARNING


O Do not depress the accelerator pedal while shifting from P (Park) or N (Neutral) to R (Reverse), D (Drive), 2
or 1. Always depress the brake pedal until shifting is completed. Failure to do so could cause you to lose con- trol and have an accident.


O Cold engine idle speed is high, so use caution when shifting into a for- ward or reverse gear before the en- gine has warmed up.


O Never shift to P (Park) or R (Reverse) while the vehicle is moving. This could cause an accident.


CAUTION


O When stopping the vehicle on an uphill grade, do not hold the vehicle by depressing the accelerator pedal. The foot brake should be used for this purpose.


O On slippery roads, do not downshift.


This may cause a loss of control.


The automatic transmission in your vehicle is electronically controlled by a transmission control module to produce maximum power and smooth operation. The recommended operating procedures for this transmission are shown on the following pages. Follow these procedures for maximum vehicle performance and driving enjoyment. Starting the vehicle O After starting the engine, fully depress the foot brake pedal to ensure the ve- hicle is at a complete stop before at- tempting to shift the selector lever.


O Keep the foot brake pedal depressed and shift the selector lever into a driving gear.


O Release the foot brake, then gradually


start the vehicle in motion.


This automatic transmission is designed so the foot brake pedal MUST be de- pressed before shifting from P (Park) to any drive position while the ignition switch is ON.


Starting and driving 5-9


Z X


The shift lever cannot be moved out of P (Park) and into any of the other gear positions if the ignition key is turned to LOCK or if the key is removed. The shift lever can be moved if the igni- tion switch is in the ACC or OFF position without depressing the foot brake pedal. This allows the vehicle to be moved if the battery is discharged.


5-10 Starting and driving


Shifting Push the button to shift into P (Park), R (Reverse) or from D (Drive) to 2. All other positions can be selected without pushing the button. P (Park) Use this selector position when the vehicle is parked or when starting the engine. Al- ways be sure the vehicle is at a complete stop. For maximum safety, depress the brake pedal, then push in the shift lever button and move the lever to the P (Park) position. Apply the parking brake. When


ASD1024


parking on a hill, apply the parking brake first, then shift the lever into the P (Park) position. Shifting from P (Park) If the ignition switch is in the ON position and the foot brake pedal is depressed, but the shift selector lever still cannot be moved out of P (Park), follow these instructions. 1. Turn the ignition key to the LOCK posi-


tion.


2. Apply the parking brake.


Z X


forward


D (Drive) Use this position for all normal driving. 2 (Second gear) Use this position for hill climbing or engine braking on downhill grades. Do not shift into the 2 position at speeds above 68 MPH (110 km/h). Do not exceed 68 MPH (110 km/h) in the 2 position. 1 (Low gear) Use this position when climbing steep hills slowly or slow driving through deep snow, sand or mud, or for maximum engine brak- ing on steep downhill grades. Do not shift into the 1 position at speeds above 34 MPH (55 km/h). Do not exceed 34
MPH (55 km/h) in the 1 position.


3. Reinsert the key and turn it to the ACC


position.


4. Depress the foot brake pedal and move


the shift selector lever to N (Neutral).


5. Start the engine. These instructions for starting the vehicle in N (Neutral) should only be used until service can be obtained at an authorized NISSAN dealership. R (Reverse): Use this position to back up. Always be sure the vehicle is at a complete stop before shifting into the R (Reverse) position. For maximum safety, check to ensure the area behind the vehicle is clear. With the brake pedal depressed, push in the shift selector lever button and move the shift selector lever to the R (Reverse) position. N (Neutral) Neither forward nor reverse gear is en- gaged. The engine can be started in this position. You may shift to N (Neutral) and restart a stalled engine while the vehicle is moving.


ASD1025


Starting and driving 5-11


Z X


Accelerator downshift In D position For rapid passing or hill climbing while driv- ing, fully depress the accelerator pedal to the floor. This shifts the transmission down into second gear or first gear, depending on the vehicle speed.


Shift lock release If the battery charge is low, the selector lever may not be moved from the P position even with the brake pedal depressed and the selector lever button pushed. To move the selector lever, push the shift lock release and selector lever button. The selector lever can be moved to N (Neutral). To push the shift lock release, complete the following procedure: 1. Turn the ignition key to the lock position


and remove the key.


2. Apply the parking brake. 3. Remove the shift lock release cover. 4. Insert a small screwdriver in the shift lock


release slot, and push down.


5. Push the selector lever button and move the selector lever to N (Neutral) position while holding down the shift lock release.


6. Start the engine. If the selector lever cannot be moved out of P (Park), take your vehicle to an authorized NISSAN dealership as soon as possible.


5-12 Starting and driving


ASD1023


Overdrive switch ON: With the engine running and the se- lector lever in the D (Drive) position, the transmission upshifts into OVER- DRIVE as vehicle speed increases.


OVERDRIVE does not engage until the engine has reached operating tempera- ture. OFF: For driving up and down long slopes where engine braking is necessary push the OVERDRIVE switch once. The O/D OFF indicator light in the instrument panel comes on at this time.


Z X


CAUTION


O Do not rest your foot on the clutch pedal while driving. This may cause clutch damage.


O Stop your vehicle completely before


shifting into R (Reverse).


O When the vehicle is stopped with the engine running (for example at a stop light), shift to N (Neutral) and release the clutch pedal with the foot brake applied.


When cruising at a low speed or climbing a gentle slope, you may feel uncomfortable shift shocks as the transmission shifts between third gear and overdrive repeatedly. In this case, depress the OVERDRIVE switch to turn the OVERDRIVE off. The O/D OFF indicator light in the instrument panel comes on at this time.


When driving conditions change, depress the overdrive switch to turn the OVER- DRIVE on. Remember not to drive at high speeds for extended periods of time with the OVER- DRIVE off. This reduces fuel economy. MANUAL TRANSMISSION


WARNING


O Do not downshift abruptly on slip- pery roads. This may cause a loss of control.


O Do not over-rev the engine when shifting to a lower gear. This may cause a loss of control or engine damage.


WDI0049


Shifting To change gears, or when up shifting or down shifting, depress the clutch pedal fully, shift into the appropriate gear, then release the clutch slowly and smoothly. You cannot shift directly from 5th gear into R (Reverse). First shift into the N (Neutral) position, then into R (Reverse). If it is difficult to move the shift lever into R (Reverse) or 1st, shift into N (Neutral), then release the clutch pedal. Depress the clutch pedal and shift into R (Reverse) or 1st again.


Starting and driving 5-13


Z X


If your vehicle is equipped with 4-wheel drive, see ‘‘ Transfer case shifting pro- cedures for four-wheel drive vehicles’’ later in this section. Suggested up-shift speeds The folllowing table provides suggested speed ranges for shifting into a higher gear. These suggestions relate to fuel economy and vehicle performance. Actual shift ranges should be adjusted for specific road conditions, weather conditions and individual driving habits. O Two-wheel drive models and four-wheel


drive models (2H and 4H position):


Shift from


MPH (km/h)


1st to 2nd 2nd to 3rd 3rd to 4th 4th to 5th


15 (24) 25 (40) 40 (64) 45 (72)


O 4-wheel drive model (4L position):


Shift from


1st to 2nd 2nd to 3rd 3rd to 4th 4th to 5th


MPH (km/h)


8 (13) 12 (19) 20 (32) 22 (35)


5-14 Starting and driving


Suggested maximum speed in each gear Downshift to a lower gear if the engine is not running smoothly, or if you need to accelerate. Do not exceed the maximum suggested speed (shown below) in any gear. For level road driving, use the highest gear suggested for that speed. Always observe posted speed limits, and drive according to the road conditions, which will ensure safe operation. Allowable maximum speed in each gear: 2-wheel drive models


MPH (km/h)


PARKING BRAKE


WARNING


O Be sure the parking brake is fully released before driving. Failure to do so can cause brake failure and lead to an accident.


O Do not release the parking brake


from outside the vehicle.


O Do not use the gear shift in place of the parking brake. When parking, be sure the parking brake is fully en- gaged.


O Do not leave children unattended in a vehicle. They could release the park- ing brake and cause an accident.


4-wheel drive models


2H/4H position


1st 2nd 3rd 4th & 5th


1st 2nd 3rd 4th & 5th


1st 2nd 3rd 4th & 5th


4L position


30 (48) 55 (88) 80 (129) − (−)


MPH (km/h)


25 (40) 43 (69) 68 (109) − (−)


12 (19) 22 (35) 30 (48) − (−)


Z X


CRUISE CONTROL (if so equipped)


button, completely.


turn the lever and push it


in


4. Before driving, be sure the brake warning


light goes out.


ASD1010


To apply: pull the lever out. To release: 1. Firmly apply foot brake. 2. Manual transmission models:


Place the gearshift position.


in the N (Neutral)


Automatic transmission models: Move the shift selector lever to the P (Park) position.


3. While pulling out on the parking brake lever slightly, push and hold the release


WSD0013


PRECAUTIONS ON CRUISE CONTROL c The cruise control system cancels auto- matically if it is not functioning properly. The SET indicator light in the instrument panel then blinks to warn the driver.


c If the SET indicator light blinks, turn the cruise control main switch off and have the system checked by an authorized NISSAN dealer.


c The SET indicator light may blink when the cruise control main switch is turned ON while pushing the RES/ACCEL, Starting and driving 5-15


Z X


COAST/SET, or CANCEL switch (located on the steering wheel). To properly use the cruise control system, use the follow- ing procedures.


WARNING


Do not use the cruise control when driving under the following conditions. c When it is not possible to keep the


vehicle at a set speed.


c In heavy traffic or in traffic that var-


ies in speed.


c On winding or hilly roads. c On slippery roads (rain, snow, ice, etc.). c In very windy areas. Doing so could cause a loss of vehicle control and result in an accident.


CAUTION


On manual transmission models, do not shift into N (Neutral) without de- pressing the clutch pedal when the cruise control is set. Should this occur, depress the clutch pedal and turn the main switch off immediately. Failure to do so may cause engine damage.


5-16 Starting and driving


CRUISE CONTROL OPERA- TIONS The cruise control allows driving at a speed between 25 to 90 MPH (40 to 144 km/h) without keeping your foot on the accelerator pedal. To turn on the cruise control, push the main switch. The CRUISE indicator light in the instrument panel comes on. To set cruising speed, accelerate the ve- hicle to the desired speed, push the COAST/SET switch and release it. The SET light in the instrument cluster comes on. Take your foot off the accelerator pedal. Your vehicle maintains the set speed. c To pass another vehicle, depress the accelerator pedal. When you release the pedal, the vehicle returns to the previ- ously set speed.


c The vehicle may not maintain the set speed when going up or down steep hills. If this happens, drive without the cruise control. To cancel the preset speed, use one of the following three methods: a) Push the CANCEL button; the SET light


in the instrument cluster goes out.


b) Tap the brake pedal; the SET light goes


out.


c) Turn the main switch off. Both the CRUISE indicator on the main switch and SET light in the instrument cluster go out. The cruise control is automatically can- celled and the SET light in the instrument panel goes out if: c you depress the brake or clutch pedal while pushing the RES/ACCEL or COAST/SET switch.


c the vehicle slows down more than 8 MPH


(13 km/h) below the set speed.


c you depress the clutch pedal (manual transmission), or move the shift selector lever to N (Neutral) (automatic transmis- sion).


To reset at a faster cruising speed, use one of the following three methods. a) Depress the accelerator pedal. When the vehicle attains the desired speed, push and release the COAST/SET switch.


b) Push and hold the RES/ACCEL switch. When the vehicle attains the speed you desire, release the switch.


Z X


c) Push and release the RES/ACCEL switch. the set speed


Each time you do this, increases by about 1 MPH (1.6 km/h).


To reset at a slower cruising speed, use one of the following three methods: a) Lightly tap the brake pedal. When the vehicle attains the desired speed, push the COAST/SET switch and release it.


b) Push and hold the COAST/SET switch. Release the switch when the vehicle slows to the desired speed.


c) Push and release the COAST/SET switch. Each time you do this, the set speed decreases by about 1 MPH (1.6
km/h).


To resume the preset speed, push and re- lease the RES/ACCEL switch. The vehicle returns to the last set cruising speed when the vehicle speed is over 25 MPH (40 km/h).


BREAK-IN SCHEDULE


INCREASING FUEL ECONOMY


During the first 1,000 miles (1,609 km), follow these recommendations for the future reliability and economy of your new vehicle. Failure to follow these recommendations may result in vehicle damage or shortened engine life. O Do not run the engine over 4,000 rpm. Avoid driving for long periods at constant speed, either fast or slow.


O Do not drive over the following speed


limits:


two-wheel drive models and four- wheel drive models (2H position):


Do not exceed the legal speed limit


four-wheel drive models (4H position):


55 MPH (88 km/h)


four-wheel drive models (4L position):


30 MPH (48 km/h)


O Do not accelerate at full throttle in any


gear.


O Avoid quick starts. O Avoid hard braking as much as possible. O Do not tow a trailer for the first 500 miles


(805 km).


SD0001
O Accelerate slowly and smoothly. Maintain cruising speeds with a constant accelera- tor position.


O Drive at moderate speeds on the high- way. Driving at high speeds lowers fuel economy.


O Avoid unnecessary stopping and brak- ing. Maintain a safe distance behind other vehicles.


O Use a proper gear range which suits road conditions. On level roads, shift into high gear as soon as possible.


O Avoid unnecessary engine idling.


Starting and driving 5-17


Z X


O Keep your engine tuned up. O Follow the recommended periodic main-


tenance schedule.


O Keep the tires inflated to the correct pressure. Low tire pressure increases tire wear and wastes fuel.


O Keep the front wheels in correct align- ment. Improper alignment increases tire wear and lowers fuel economy.


O Air conditioner operation lowers fuel economy. Use the air conditioner only when necessary.


O When cruising at highway speeds, it is more economical to use the air condi- tioner and leave the windows closed to reduce drag.


Use 4H or 4L position only when neces- sary. Four-wheel drive operation lowers fuel economy.


5-18 Starting and driving


USING FOUR-WHEEL DRIVE


in four-wheel drive. Driving on dry hardsurfaces in 4H or 4L may cause unnecessary noise, tire wear and in- creased fuel consumption. NISSAN recommends driving in the 2H position under these conditions.


WARNING


O When parking the vehicle, apply the parking brake and shift the transfer control lever into the 2H, 4H or 4L position.


ASD1022


TRANSFER CASE SHIFTING PROCEDURES


CAUTION


Do not drive on dry, hard surface roads


if


even


O Do not leave the transfer control le- ver in the N (Neutral) position. Oth- erwise, the vehicle could roll unex- pectedly the manual transmission is in any gear or the automatic transmission is in the P (Park) position. If the ATP light is on, this indicates that the automatic transmission P position will not function and the transfer control le- ver is in the N position.


Z X


O Failure to engage the transfer con- trol lever in 2H, 4H, or 4L could result in the vehicle moving unexpectedly, resulting in serious personal injury or property damage.


2H — (2WD, high range) Only the rear wheels are driven. Use for driving under the same conditions as standard 2WD vehicles or state dynamometer I/M testing. 4H — (4WD, high range) Four wheels are driven. Use when driving on roads where it is difficult to drive in the 2H position (i.e., driving at normal speeds on snow covered, icy, wet, muddy or sandy roads). 4L — (4WD, low range) Four wheels are driven. Use when climbing or descending steep hills, or during hard driving in sand, mud or deep snow. The 4L position provides maximum power and traction. Avoid raising vehicle speed excessively, as the maximum speed is approximately 30 MPH (48 km/h). N — No wheels are driven. Always keep the transfer lever out of the N (Neutral) position. Shift the lever quickly and smoothly when moving across the N (Neutral) position with the vehicle stopped.


SD0021


AUTO-LOCK FREE-


RUNNING HUBS Your NISSAN is equipped with auto-lock free-running hubs. The auto-lock free-running hub is designed to allow for automatic four-wheel drive en- gagement when the shift lever is moved to the 4H or 4L position. Follow these opera- tional cautions:


O The auto-locking hubs will make a


CAUTION


clicking noise when engaging and disengaging. This is normal.


O Accelerating quickly from a stop af- ter shifting from two-wheel drive to four-wheel drive may not allow en- gagement of the auto-locking free- running hubs and may cause a clat- tering noise. Continued use of the vehicle with this noise may damage the hub lock. In such a case, release the accelerator pedal to reduce the engine speed or stop the vehicle.


O If the auto-locking hubs make a clat- tering noise after shifting from four- wheel drive to two-wheel drive, stop and move the vehicle in reverse gear, in a straight line, about 7 to 10
feet (2 to 3 m).


O Under extremely cold conditions [below 5°F (-15°C)], the front axle shafts may rotate even with the transfer lever in the 2H position. If this occurs, the auto-locking hubs may make a clattering noise. To avoid this, drive first in four-wheel drive to warm up the vehicle and differential gear oil. Then, shift to two-wheel drive.


Starting and driving 5-19


Z X


O In cold weather, it may be necessary to reduce speed or stop the vehicle in order to shift from two-wheel drive to four-wheel drive.


O When shifting into or out of four- wheel drive while driving, do not stop shift lever movement midway. An incomplete shift may cause a clattering noise from the auto- locking hubs. Continued use of the vehicle with this noise may damage the hub lock. Drive in four-wheel drive to stop the noise. Shift to two- wheel drive as described.


5-20 Starting and driving


Z X


TO SHIFT


TRANSFER CASE:


SHIFT PROCEDURE FOR AUTO-LOCK FREE-RUNNING HUBS


From 2H to 4H


Move the transfer case shift lever to 4H at speeds below 25 MPH (40 km/h). It is not necessary to depress the clutch pedal. Perform this operation when driving straight, not while cornering.


From 4H to 2H


1. Move the transfer case shift lever to 2H. This can be done at any speed, and it is not necessary to depress the clutch pedal. Per-


form this operation when driving straight, not while cornering.


2. Disengage the AUTO-LOCK hubs following the procedure outlined below. NOTE: The 4WD indicator light may not turn off immediately under certain driving conditions, such as when the vehicle is driven uphill. This is normal and it will shut off as the vehicle is driven further. AUTO-LOCK HUB DISENGAGEMENT (FREE MODE) The AUTO-LOCK hubs will not disengage until the vehicle is completely stopped and is then moved in a straight line, approximately 7-10 feet (2-3 m), in the opposite direction of travel. For example: If you were driving the vehicle forward, stop and move the vehicle 7-10 feet (2-3 m) backward. If you were driving the vehicle in reverse, stop and move the vehicle 7-10 feet (2-3 m) forward. It is not necessary to immediately return the AUTO-LOCK hubs to FREE MODE when shifting from 4H to 2H. The vehicle may be operated under normal 2H conditions with the AUTO-LOCK hubs engaged. However, disengaging the AUTO-LOCK hubs will allow for better fuel economy, quieter ride and less component wear. Leaving the hubs locked while driving in 2H may be desirable so that you can easily shift to 4H at speeds greater than 25 MPH (40 km/h).


From 4H to 4L or 4L to 4H


1. Stop the vehicle. 2. Depress the clutch pedal, or place the transmission selector lever in the N (Neutral) position. 3. Depress the transfer case shift lever and move it to the 4L or 4H position. Change gears quickly and smoothly.


From 2H to 4L


From 4L to 2H


1. Stop the vehicle. 2. Depress the clutch pedal, or place the transmission selector lever in the N (Neutral) position. 3. Depress the transfer case shift lever and move it to the 4L position. Change gears quickly and smoothly.


1. Stop the vehicle. 2. Depress the clutch pedal, or place the transmission selector lever in the N (Neutral) position. 3. Depress the transfer case shift lever and move it to the 2H position. Change gears quickly and smoothly. 4. Disengage the AUTO-LOCK hubs following the procedure outlined above.


Starting and driving 5-21


Z X


PARKING/PARKING ON HILLS


MSD0002


WARNING


O Do not park the vehicle over flam- mable materials such as dry grass, waste paper or rags. They may ignite and cause a fire.


The transfer control


lever must be in the 2H, 4H or 4L position and the parking brake set to prevent the vehicle from rolling.


O Never place the transfer control le- ver in the N (Neutral) position. Oth- erwise, the vehicle could roll unex-


pectedly even if the manual trans- mission is in gear or the automatic transmission is in the P (Park) posi- tion. This could result in serious in- jury or property damage.


O Safe parking procedures require that both the parking brake be set and the transmission placed into P (Park) for automatic transmission models or in an appropriate gear for manual transmission models. Failure to do so could cause the vehicle to move unexpectedly or roll away and result


5-22 Starting and driving


in an accident. Make sure the shift lever has been pushed as far forward as it can go and cannot be moved without depressing the button at the end of the lever.


O Never leave the engine running while


the vehicle is left unattended.


O Do not leave children unattended in- side the vehicle. They could unknow- ingly activate switches or controls. Unattended children could become involved in serious accidents.


O If the ATP lamp is ON, this indicates that the automatic transmission P (park) position will not function and the transfer control lever is in the N (neutral) position. Failure to engage the transfer control lever in the 2H, 4H or 4L position could result in the vehicle moving unexpectedly, result- ing in serious personal injury or property damage.


1. Firmly apply the parking brake. 2. Manual transmission models:


Place the gearshift lever in the R (Re-


Z X


POWER STEERING


BRAKE SYSTEM


The power assisted steering is designed to use a hydraulic pump, driven by the engine, to assist steering. If the engine stops or drive belt breaks, you will still have control of the vehicle. How- ever, much greater steering effort is needed, especially in sharp turns and at low speeds.


WARNING


If the engine is not running or is turned off while driving, the power assist for the steering will not work. Steering will be much harder to operate.


verse) position. When parking on an up- hill grade, place the gearshift lever in the 1st position. Automatic transmission models: Move the gearshift lever to the P (Park) position.


3. To help prevent the vehicle from rolling into the street when parked on an incline, it is a good practice to turn the wheels as illustrated.


O HEADED DOWNHILL WITH CURB: (cid:192) s1
Turn the wheels into the curb and move the vehicle forward until the curb side wheel gently touches the curb.


O HEADED UPHILL WITH CURB: s2


Turn the wheels away from the curb and move the vehicle back until the curb side wheel gently touches the curb.


O HEADED UPHILL OR DOWNHILL, NO


CURB: s3
Turn the wheels toward the side of the road so the vehicle will move away from the center of the road if it moves.


4. Turn the ignition key to the LOCK posi-


tion and remove the key.


The brake system has two separate hydrau- lic circuits. If one circuit malfunctions, you will still have braking at two wheels. BRAKING PRECAUTIONS Vacuum assisted brakes The brake booster aids braking by using engine vacuum. If the engine stops, you can stop the vehicle by depressing the brake pedal. However, greater foot pressure on the brake pedal will be required to stop the vehicle and stopping distance will be longer. Using the brakes Avoid resting your foot on the brake pedal while driving. This will overheat the brakes, wear out the brake linings and pads faster, and reduce gas mileage. To help reduce brake wear, and to prevent the brakes from overheating, reduce speed and downshift to a lower gear before going down a slope or long grade.


Starting and driving 5-23


Z X


WARNING


O While driving on a slippery surface, be careful when braking, accelerat- ing or downshifting. Abrupt braking or accelerating could cause the wheels to skid and result in an acci- dent.


O If the engine is not running or is turned off while driving, the power assist for the brakes will not work. Braking will be harder.


Wet brakes When the vehicle is washed or driven through water, the brakes may get wet. As a result, your braking distance will be longer and the vehicle may pull to one side during braking. To dry the brakes, drive the vehicle at a safe speed while lightly pressing the brake pedal to heat the brakes. Do this until the brakes return to normal. Avoid driving the vehicle at high speeds until the brakes function cor- rectly.


5-24 Starting and driving


ANTI-LOCK BRAKE SYSTEM (ABS) Using the System Depress the brake pedal and hold it down.


WARNING


Do not pump the brake pedal. Doing so may result in increased stopping dis- tances.


Normal operation The anti-lock brake system does not oper- ate at speeds below 3 to 6 MPH (5 to 10
km/h). (The speeds vary according to road conditions.) When driving, the anti-lock brake system controls the wheels so they will not lock when braking abruptly or when braking on a slippery road. Thus, difficult steering and swerving of the vehicle due to locked wheels is minimized. The system detects the wheel rotation rate and electronically controls the pressure applied to each brake. Slight vibration on the brake pedal accom- panied by noise usually occurs while the ABS system is operating. Such vibration and noise encountered during abrupt brak-


ing is not a problem, but indicates that the system is functioning. Self-test feature The anti-lock brake system consists of elec- tronic sensors and hydraulic solenoids con- trolled by a computer. The computer has a built-in diagnostic feature that tests the sys- tem each time you start the engine and move the vehicle at a low speed in forward or reverse. When the self-test occurs, you may hear a ‘‘clunk’’ noise and/or feel a pulsation in the brake pedal. This is normal and is not an indication of any malfunction. If the computer senses any malfunction, it switches the anti-lock brake system off and turns on the ABS brake warning light in the dashboard. The brake system then operates normally, but without anti-lock assistance. If an abnormality occurs in the system, the anti-lock function will cease but the ordinary brakes will continue to operate normally. The ABS brake warning light will then come on. If the light comes on while you are driving, contact an authorized NISSAN dealer for repair.


Z X


WARNING


that


remember


O The anti-lock brake system is a sophisticated device, but it cannot prevent accidents resulting from careless or dangerous driving tech- niques. It can help maintain vehicle control under braking on slippery surfaces, but the stopping distance on slippery sur- faces will be longer than on normal surfaces even with the anti-lock brake system. Stopping distances may also be longer on rough, gravel, or snow covered roads, or if you are using tire chains. Always maintain a safe distance from the vehicle in front of you. Ultimately, the respon- sibility for safety of self and others rests in the hands of the driver.


Tire type and condition may also affect braking effectiveness. O When replacing tires,


the specified tire size on all four wheels. O When installing a spare tire, make sure it is the proper size and type as specified on the tire placard. For tire


install


placard location information refer to ‘‘Tire placard’’ in the ‘‘Technical and consumer information’’ section of this manual.


COLD WEATHER DRIVING


FREEING A FROZEN DOOR LOCK To prevent a door lock from freezing, apply de-icer or glycerin through the key hole. If the lock becomes frozen, heat the key be- fore inserting it in the key hole. ANTI-FREEZE In the winter when it is anticipated that the temperature will drop below 32°F (0°C), check anti-freeze (ethylene glycol base) to assure proper winter protection. For details, see ‘‘Engine cooling system’’ in the ‘‘Do-it- yourself’’ section of this manual. BATTERY If fully charged during extremely cold weather conditions, the bat- tery fluid may freeze and damage the bat- tery. To maintain maximum efficiency, the battery should be checked regularly. For details, see ‘‘Battery’’ in the ‘‘Do-it-yourself’’ section of this manual. DRAINING OF COOLANT WATER If the vehicle is to be left outside without anti-freeze, drain the cooling system by open- ing the drain valves located under the radiator Starting and driving 5-25


the battery is not


Z X


and on the engine block. Refill before operat- ing the vehicle. For details, see ‘‘Changing engine coolant’’ in the ‘‘Do-it-yourself’’ section of this manual. TIRE EQUIPMENT 1. SUMMER tires have a tread designed to provide superior performance on dry pavement. However, the performance of these tires will be substantially reduced in snowy and icy conditions. If you oper- ate your vehicle on snowy or icy roads, NISSAN recommends the use on all four wheels of MUD & SNOW or ALL SEA- SON tires. Please consult your NISSAN dealer for the tire type, size, speed rating and availability information.


2. For additional traction on icy roads, stud- ded tires may be used. However, some U.S. states and Canadian provinces pro- hibit their use. Check local, state and pro- vincial laws before installing studded tires. Skid and traction capabilities of studded snow tires on wet or dry surfaces may be poorer than that of non-studded snow tires. 3. Tire chains may be used. Use of


tire chains may be prohibited according to


5-26 Starting and driving


laws before location. Check the local installing tire chains. When installing tire chains, make sure they are of proper size for the tires on your vehicle and are installed according to the chain manufac- turer’s suggestions. Use only SAE Class ‘‘S’’ chains. Other types may damage your vehicle. Use chain tension- ers when recommended by the tire chain manufacturer to ensure a tight fit. Loose end links of the tire chain must be se- cured or removed to prevent the possi- bility of whipping action damage to the fenders or undercarriage. If possible, avoid fully loading your vehicle when using tire chains. In addition, drive at a reduced speed, otherwise, your vehicle may be damaged and/or vehicle handling and performance may be adversely af- fected. Never install tire chains on a TEMPORARY USE ONLY spare tire. Do not use tire chains on dry roads.


SPECIAL WINTER EQUIPMENT It is recommended that the following items be carried in the vehicle during winter: 1. A scraper and stiff-bristled brush to re- move ice and snow from the windows and wiper blades.


2. A sturdy, flat board to be placed under


the jack to give it firm support.


3. A shovel to dig the vehicle out of snow-


drifts.


4. Extra window washer fluid to refill the


reservoir tank.


DRIVING ON SNOW OR ICE


WARNING


O Wet ice (32°F, 0°C and freezing rain), very cold snow, or ice can be slick and very hard to drive on. The ve- hicle will have much less traction or ‘‘grip’’ under these conditions. Try to avoid driving on wet ice until the road is salted or sanded.


O Whatever the condition, drive with caution. Accelerate and slow down with care. If accelerating or down- shifting too fast, the drive wheels will lose even more traction.


O Allow more stopping distance under these conditions. Braking should be started sooner than on dry pavement. O Allow greater following distances on


slippery roads.


Z X


O Watch for slippery spots (glare ice). These may appear on an otherwise clear road in shaded areas. If a patch of ice is seen ahead, brake before reaching it. Try not to brake while on the ice, and avoid any sudden steer- ing maneuvers.


O Do not use the cruise control on


slippery roads.


O Snow can trap dangerous exhaust gases under your vehicle. Keep snow clear of the exhaust pipe and from around your vehicle.


ENGINE BLOCK HEATER (if so equipped) An engine block heater to assist extreme cold temperature starting is available through an authorized NISSAN dealer.


WARNING


Do not use your heater with an un- grounded electrical system or two- pronged (cheater) adapters. You can be injured by an electrical shock if you use an ungrounded connection.


Starting and driving 5-27


Z X


MEMO


5-28 Starting and driving


Z X


6 In case of emergency


First aid kit..............................................................6-2
Flat tire ...................................................................6-2
Changing a flat tire............................................6-2
Jump starting..........................................................6-8
Push starting ........................................................6-10


If your vehicle overheats......................................6-10
Towing your vehicle..............................................6-11
Towing recommended by Nissan ....................6-12
Vehicle recovery (freeing a stuck vehicle) ............................................................6-14


Z X


FIRST AID KIT


FLAT TIRE


CHANGING A FLAT TIRE If you have a flat tire, follow the instructions below: Stopping the vehicle 1. Safely move the vehicle off the road and


away from traffic.


2. Turn on the hazard warning flashers. 3. Park on a level surface and apply the parking brake. Shift the manual transmis- sion into R (Reverse), or the automatic transmission into P (Park).


ACE1041


A first aid kit is located on the back door trim panel. To remove the first aid kit, unfasten the two straps.


6-2 In case of emergency


WARNING


The transfer control


lever must be in the 2H, 4H or 4L position. O Do not leave the transfer control le- ver in the N (Neutral) position. Other- wise, the vehicle could roll unexpect- edly even if the manual transmission is in any gear or the automatic trans- mission is in the P (Park) position. This could result in serious personal injury or property damage.


4. Turn off the engine.


Z X


5. Raise the hood to warn other traffic and to signal professional road assistance personnel that you require assistance.


6. Have all passengers get out of the ve- hicle and stand in a safe place away from traffic and clear of the vehicle.


WARNING


O Make sure the parking brake is se- curely applied and the manual trans- mission is shifted into R (Reverse), or the automatic transmission into P (Park).


O Never change tires when the vehicle is on a slope, ice or slippery areas. This is hazardous.


O Never change tires if oncoming traf- fic is close to your vehicle. Wait for professional road assistance.


MCE0001


ACE1051


Blocking wheels Place suitable blocks at both the front and back of the wheel diagonally opposite the flat tire to prevent the vehicle from rolling when it is jacked up.


WARNING


Be sure to block the wheel as the ve- hicle may move and result in personal injury.


Getting the spare tire and tools 1. Open the back door. 2. Roll back the cargo area carpet. 3. Remove the wheel nut wrench and jack rod. 4. Unscrew the tool tray hold down and


remove the tool tray.


5. Use the tool tray to store lug nuts during


a tire change.


WARNING


Never use the tool tray as a jacking surface.


In case of emergency 6-3


Z X


ACE1033


ACE1034


6. Unscrew the jack hold down and re-


move the jack.


7. Find the oval shaped opening above the middle of the license plate. Pass the T-shaped end of the jack rod through the opening and direct it towards the spare tire winch, located directly above the spare tire.


CAUTION


Do not insert the jack rod straight as it is designed to be inserted at an angle as shown.


6-4 In case of emergency


WCE0016


8. Fit the square end of the jack rod into the square hole of the wheel nut wrench to form a handle.


9. Seat the T-shaped end of the jack rod into the T-shaped opening of the tire winch. Apply pressure to keep the jack


Z X


rod engaged in the spare tire winch and turn the jack rod counter clockwise to lower the spare tire.


10.Once the spare tire is completely low- ered, reach under the vehicle, remove the retainer chain, and carefully slide the tire from under the rear of the vehicle.


CAUTION


Be sure to center the spare tire sus- pending plate on the wheel and then lift the spare tire.


CE0047M


ACE1040


In case of emergency 6-5


Z X


Removing wheel cover


CAUTION


Do not use your hands to pry off wheel caps or wheel covers. Doing so could result in personal injury.


Use caution not to scratch the wheel cover or wheel surface.


6-6 In case of emergency


Jacking up the vehicle and remov- ing the wheel Always refer to the proper illustrations for the correct placement and jack-up points for your specific vehicle model and jack type.


WCE0017


WARNING


O Never get under the vehicle while it


is supported only by the jack.


O Use only the jack provided with your vehicle to lift the vehicle. Do not use the jack provided with your vehicle on other vehicles. The jack is de- signed for lifting only your vehicle during a tire change.


O Use the correct jack up points. Never use any other part of the vehicle for jack support.


Z X


O Never jack up the vehicle more than


necessary.


O Never use blocks on or under the


jack.


O Never use the tool tray as a jacking


surface.


O Do not allow passengers to stay in


the vehicle while it is on the jack.


O Do not start or run engine while vehicle is on the jack. It may cause the vehicle to move. This is espe- cially true for vehicles with limited slip differential carriers.


WCE0015


WARNING


O Incorrect wheel nuts or improperly tightened wheel nuts can cause the wheel to become loose or come off. This could cause an accident.


O Do not use oil or grease on the wheel studs or nuts. This could cause the nuts to become loose.


Installing the spare tire 1. Clean any mud or dirt from the surface


between the wheel and hub.


2. Carefully put the spare tire on and tighten


the wheel nuts finger tight.


3. With the wheel nut wrench, tighten the wheel nuts alternately and evenly until they are tight.


4. Lower the vehicle slowly until


the tire touches the ground. Then, with the wheel nut wrench, tighten the wheel nuts se- curely in the sequence as illustrated. Lower the vehicle completely.


As soon as possible, tighten the wheel nuts to the specified torque with a torque wrench. Wheel nut tightening torque:


87 to 108 ft-lb (118 to 147 Nzm)


The wheel nuts must be kept tightened to specification at all times. It is recom- mended that wheel nuts be tightened to specification at each lubrication interval. Adjust tire pressure to the COLD pres- sure.


In case of emergency 6-7


Z X


JUMP STARTING


To start your engine with a booster battery, the instructions and precautions below must be followed.


WARNING


O If done incorrectly, jump starting can lead to a battery explosion, resulting in severe injury or death. It could also damage your vehicle.


O Explosive hydrogen gas is always present in the vicinity of the battery. Keep all sparks and flames away from the battery.


O Do not allow battery fluid to come into contact with eyes, skin, clothing or painted surfaces. Battery fluid is a corrosive sulphuric acid solution which can cause severe burns. If the fluid should come into contact with anything, immediately flush the con- tacted area with water.


O Keep battery out of the reach of


children.


O The booster battery must be rated at 12 volts. Use of an improperly rated battery can damage your vehicle.


COLD pressure: After vehicle has been parked for three hours or more or driven less than 1 mile (1.6 km). COLD tire pressures are shown on the tire placard affixed to the inside of the glove box lid. O Retighten the wheel nuts when the vehicle has been driven for 600 miles (1,000 km) (also in cases of a flat tire, etc.).


5. Securely store the flat tire and jacking


equipment in the vehicle.


WARNING


Always make sure that the spare tire and jacking equipment are properly se- cured after use. Such items can be- come dangerous projectiles in an acci- dent or sudden stop.


6-8 In case of emergency


O Your vehicle has and automatic en- gine cooling fan. It could come on at any time. Keep hands and other ob- jects away from it.


O Whenever working on or near a bat- tery, always wear suitable eye pro- tectors (for example, goggles or in- dustrial and remove rings, metal bands, or any other jewelry. Do not lean over the battery when jump starting.


spectacles)


safety


O Do not attempt to jump start a frozen battery. It could explode and cause serious injury.


WARNING


Always follow the instructions be- low. Failure to do so could result in damage to the charging system and cause personal injury.


1. If the booster battery is in another vehicle, position the two vehicles to bring their batteries into close proximity to each other. Do not allow the two vehicles to touch. 2. Apply the parking brake. Move the shift selector lever to N (Neutral) (on auto-


Z X


matic transmission models, move the lever to P (Park)). Switch off all unneces- sary electrical systems (lights, heater, air conditioner, etc.).


3. Remove vent caps on the battery (if so equipped). Cover the battery with an old cloth to reduce explosion hazard.


4. Connect jumper cables in the sequence


as illustrated.


ACE1018


CAUTION


O Always connect positive (+) to posi- tive (+) and negative (−) to body ground (for example, engine lift bracket, etc.) — not to the battery.


O Make sure the jumper cables do not touch moving parts in the engine compartment and that the cable clamps do not contact any other metal.


Loading...
x