2009 Nissan Rogue Owners Manual

the LOCK position. This function indicates the security systems equipped on the vehicle are operational.

If the NISSAN Vehicle Immobilizer System is malfunctioning, this light will remain on while the ignition switch is in the ON position.

If the light still remains on and/or the engine will not start, see a NISSAN dealer for NISSAN Vehicle Immobilizer System

Instruments and controls 2-21

Model "S35-D" EDITED: 2008/ 7/ 24

service as soon as possible. Please bring all registered keys that you have when visiting a NISSAN dealer for service.

Black plate (88,1)

WINDSHIELD WIPER AND WASHER SWITCH

WARNING

mix the washer fluid concentrate and water.

In freezing temperatures the washer solution may freeze on the windshield and obscure your vision which may lead to an accident. Warm windshield with the defroster before you wash the windshield.

CAUTION

. Do not operate the washer continu-

ously for more than 30 seconds.

. Do not operate the washer if the

reservoir tank is empty.

If the windshield wiper operation is inter- rupted by snow or ice, the wiper may stop moving to protect its motor. If this occurs, turn the wiper switch to the OFF position and remove the snow or ice that is on and around the wiper arms. In approximately 1
minute, turn the switch on again to operate the wiper.

. Do not

fill

the window washer reservoir tank with washer fluid concentrates at full strength. Some methyl alcohol based washer fluid concentrates may permanently stain the grille if spilled while filling the window washer reservoir tank.

. Pre-mix washer fluid concentrates with water to the manufacturer’s recommended levels before pouring the fluid into the window washer reservoir tank. Do not use the window washer reservoir tank to

2-22 Instruments and controls

Model "S35-D" EDITED: 2008/ 7/ 24

times.

The windshield wiper and washer operates when the ignition switch is in the ON position.

SIC2821

Push the lever down to operate the wiper at the following speed: *1

Intermittent — intermittent operation can be adjusted by turning the knob toward *A (Slower) or *B (Faster).

*2 Low — continuous low speed operation *3 High — continuous high speed operation Push the lever up *4
to have one sweep operation of the wiper. Pull the lever toward you *5
to operate the washer. Then the wiper will also operate several

Black plate (89,1)

REAR WINDOW WIPER AND WASHER SWITCH

WARNING

In freezing temperatures the washer solution may freeze on the rear window glass and obscure your vision. Warm the rear window with the defroster before you wash the rear window.

CAUTION

. Do not operate the washer continu-

ously for more than 30 seconds.

. Do not operate the washer if the

reservoir tank is empty.

. Do not

fill

the window washer reservoir tank with washer fluid concentrates at full strength. Some methyl alcohol based washer fluid concentrates may permanently stain the grille if spilled while filling the window washer reservoir tank.

. Pre-mix washer fluid concentrates with water to the manufacturer’s recommended levels before pouring the fluid into the window washer reservoir tank. Do not use the window washer reservoir tank to mix the washer fluid concentrate

Instruments and controls 2-23

Model "S35-D" EDITED: 2008/ 7/ 24

Black plate (90,1)

REAR WINDOW AND OUTSIDE MIRROR DEFROSTER SWITCH

SIC3480

SIC3481

The rear window wiper and washer operate when the ignition switch is in the ON position.

Turn the switch clockwise from the OFF position to operate the wiper. *1

Intermittent (INT) — intermittent operation (not adjustable)

tion

*2 Low (ON) — continuous low speed opera- Push the switch forward *3
to operate the washer. Then the wiper will also operate several times.

To defog/defrost the rear window glass and outside mirrors (if so equipped), start the engine and push the switch on. The indicator light *1
will illuminate. Push the switch again to turn the defroster off.

It will automatically turn off in approximately 15
minutes.

CAUTION

When cleaning the inner side of the rear window, be careful not to scratch or damage the rear window defroster.

Model "S35-D" EDITED: 2008/ 7/ 24

and water.

If the rear window wiper operation is interrupted by snow or ice, the wiper may stop moving to protect its motor. If this occurs, turn the wiper switch to the OFF position and remove the snow or ice that is on and around the wiper arms. In approxi- mately 1 minute, turn the switch on again to operate the wiper.

2-24 Instruments and controls

.

off the headlights for short intervals (for example, when the vehicle stops at a traffic signal).

If the xenon headlight bulb is close to burning out, the brightness will drasti- cally decrease, the light will start blinking, or the color of the light will become reddish. If one or more of the above signs appear, contact a NISSAN dealer.

HEADLIGHT AND TURN SIGNAL SWITCH

XENON HEADLIGHTS (if so equipped)

WARNING

HIGH VOLTAGE

. When xenon headlights are on, they produce a high voltage. To prevent an electric shock, never attempt to modify or disassemble. Always have your xenon headlights replaced at a NISSAN dealer.

. Xenon headlights provide consider- ably more light than conventional headlights. If they are not correctly aimed, they might temporarily blind an oncoming driver or the driver ahead of you and cause a serious accident. If headlights are not aimed correctly, immediately take your ve- hicle to a NISSAN dealer and have the headlights adjusted correctly.

When the xenon headlight is initially turned on, its brightness or color varies slightly. However, the color and brightness will soon stabilize.

The life of xenon headlights will be shortened by frequent on-off opera- tion. It is generally desirable not to turn

Black plate (91,1)

Type A

SIC2745

Type B

SIC3019

Instruments and controls 2-25

Model "S35-D" EDITED: 2008/ 7/ 24

HEADLIGHT SWITCH Lighting *1 Turn the switch to the

position:

The front park, side marker, plate and instrument lights will come on.

tail,

license

*2 Turn the switch to the

position:

Headlights will come on and all the other lights remain on.

2-26 Instruments and controls

Black plate (92,1)

has been pushed to the OFF position.

or

. When the headlight switch remains in the the lights automatically turn off, the lights will turn on when the ignition switch is pushed to the ON position.

position after

SIC3484

Headlight beam select *1 To select the low beam, put the lever in the

neutral position as shown.

*2 To select the high beam, push the lever

forward while the switch is in the position. Pull it back to select the low beam. *3 Pulling the lever toward you will flash the headlight high beam even when the head- light switch is in the OFF position.

Battery saver system . When the headlight switch is in the

or position while the ignition switch is in the ON position, the lights will automatically turn off 5 minutes after the ignition switch

CAUTION

. When you turn on the headlight switch again after the lights auto- matically turn off, the lights will not turn off automatically. Be sure to turn the light switch to the OFF position when you leave the vehicle for extended periods of time, other- wise the battery will be discharged. . Never leave the light switch on when the engine is not running for extended periods of time even if the headlights turn off automatically.

Model "S35-D" EDITED: 2008/ 7/ 24

Black plate (93,1)

WARNING

WARNING

Xenon headlights are extremely bright compared to conventional headlights. If the xenon headlights hit the rearview mirror of the vehicle ahead or the windshield of oncoming vehicle, the driver of these vehicles may have difficulty driving because of the bright- ness. Use the headlight aiming control switch to lower the light axis. See “XENON HEADLIGHTS” earlier in this section for additional information.

Daytime running light system (Canada only) The daytime running lights automatically illumi- nate when the engine is started with the parking brake released. The daytime running lights operate with the headlight switch in the OFF position or position. Turn the headlight switch to the position for full illumination when driving at night.

in the

If the parking brake is applied before the engine is started, the daytime running lights do not illuminate. The daytime running lights illuminate once the parking brake is released. The daytime running lights will remain on until the ignition switch is turned to the OFF position.

SIC2275

Headlight aiming control (if so equipped) Depending on the number of occupants in the vehicle and the load it is carrying, the headlight axis may be higher than desired. If the vehicle is traveling on a hilly road, the headlights may directly hit the rearview mirror of the vehicle ahead or the oncoming vehicle. The light axis can be lowered with the operation of the switch.

the windshield of

The larger the number designated on the switch, the lower the axis.

When traveling with no heavy load or on a flat road, select position 0.

When the daytime running light system is active, tail lights on your vehicle are not on. It is necessary at dusk to turn on your headlights. Failure to do so could cause an accident injuring yourself and others.

Instruments and controls 2-27

Model "S35-D" EDITED: 2008/ 7/ 24

Instrument brightness control The instrument brightness control operates when the headlight switch is in the or

position.

Turn the control *A to adjust the brightness of lights. The brightness the instrument panel indicator *B will be shown briefly in the vehicle information display when the control is turned.

When the brightness level reaches the maximum or minimum, a beep will sound.

SIC3958

2-28 Instruments and controls

SIC3959

Black plate (94,1)

SIC3488

TURN SIGNAL SWITCH *1 Turn signal Move the lever up or down to signal the turning direction. When the turn is completed, the turn signals cancel automatically. *2 Lane change signal To indicate a lane change, move the lever up or down to the point where lights begin flashing.

Model "S35-D" EDITED: 2008/ 7/ 24

HAZARD WARNING FLASHER SWITCH

Black plate (95,1)

Turn signals do not work when the hazard warning flasher lights are on.

The flasher can be actuated with the ignition switch in any position.

Some state laws may prohibit the use of the hazard warning flasher switch while driving.

SIC3020

SIC2574

FOG LIGHT SWITCH (if so equipped) To turn the fog lights on, turn the headlight switch to the position, then turn the switch to the position. To turn them off, turn the switch to the OFF position.

The headlights must be on for the fog lights to operate.

When the headlight high-beam is selected, the fog lights turn off.

Push the switch on to warn other drivers when you must stop or park under emergency condi- tions. All turn signal lights will flash.

WARNING

If stopping for an emergency, be sure to move the vehicle well off the road.

. Do not use the hazard warning flashers while moving on the high- way unless unusual circumstances force you to drive so slowly that your vehicle might become a hazard to other traffic.

Instruments and controls 2-29

Model "S35-D" EDITED: 2008/ 7/ 24

HORN

HEATED SEATS (if so equipped)

CAUTION

The battery could run down if the seat heater is operated while the engine is not running.

. Do not use the seat heater for extended periods or when no one is using the seat.

. Do not put anything on the seat which insulates heat, such as a blanket, cushion, seat cover, etc. Otherwise, the seat may become overheated.

. Do not place anything hard or heavy on the seat or pierce it with a pin or similar object. This may result in damage to the heater.

. Any liquid spilled on the heated seat should be removed immediately with a dry cloth.

. When cleaning the seat, never use gasoline, thinner, or any similar materials.

If any abnormalities are found or the heated seat does not operate, turn the switch off and have the system checked by a NISSAN dealer.

To sound the horn, push the center pad area of the steering wheel.

SIC3404

WARNING

Do not disassemble the horn. Doing so could affect proper operation of the supplemental front air bag system. Tampering with the supplemental front air bag system may result in serious personal injury.

2-30 Instruments and controls

Black plate (96,1)

SIC3355

The front seats are warmed by built-in heaters. The switches located on the center console can be operated independently of each other.

1. Start the engine.

2. Select heat range.

*1 For high heat, push the HI (High) side of

the switch.

*2 For low heat, push the LO (Low) side of

the switch.

The indicator light in the switch *3 will illuminate when low or high is selected.

3. To turn off the heater, return the switch to the level position. Make sure the indicator

Model "S35-D" EDITED: 2008/ 7/ 24

Black plate (97,1)

VEHICLE DYNAMIC CONTROL (VDC) OFF SWITCH

CLOCK

light goes off.

The heater is controlled by a thermostat, automatically turning the heater on and off. The indicator light will remain on as long as the switch is on.

When the vehicle’s interior is warmed, or before you leave the vehicle, be sure to turn off the switch.

SIC1881

SIC3548

The vehicle should be driven with the Vehicle Dynamic Control (VDC) system on for most driving conditions.

If the vehicle is stuck in mud or snow, the VDC system reduces the engine output to reduce wheel spin. The engine speed will be reduced even if the accelerator is depressed to the floor. If maximum engine power is needed to free a stuck vehicle, turn the VDC system off.

To turn off the VDC system, push the VDC OFF switch. The

indicator will illuminate.

Push the VDC OFF switch again or restart the engine to turn on the system. (See “VEHICLE DYNAMIC CONTROL (VDC) SYSTEM” in the “5. Starting and driving” section.)

The digital clock (in the audio unit) displays time when the ignition switch is in the ACC or ON position. Push the CLOCK button *1
or off.

to turn the clock on

ADJUSTING THE TIME 1. Push and hold the CLOCK button *1 until

the display shows “H-Seek M-Tune”.

2. Push the SEEK/TRACK button *2

to adjust

the hours.

3. Push the TUNE/FF·REW button *3

to

adjust the minutes.

4. Push the CLOCK button *1

again to exit Instruments and controls 2-31

Model "S35-D" EDITED: 2008/ 7/ 24

POWER OUTLET

the clock set mode.

The display will display after 10 seconds.

return to the regular clock

If the power supply is disconnected, the clock will not indicate the correct time. Readjust the time.

Instrument panel

SIC3492

2-32 Instruments and controls

Center console (if so equipped)

SIC3493

Black plate (98,1)

The power outlet is located in the instrument panel and the center console (if so equipped).

CAUTION

The outlet and plug may be hot during or immediately after use.

. Do not use with accessories that exceed a 12 volt, 120W (10A) power draw. Do not use double adapters or more than one electrical accessory. . Use power outlet with the engine running to avoid discharging the vehicle battery.

. Avoid using power outlet when the air conditioner, headlights or rear window defroster is on.

This power outlet is not designed for use with a cigarette lighter unit. . Push the plug in as far as it will go. If good contact is not made, the plug may overheat or the internal tem- perature fuse may open.

. Before inserting or disconnecting a plug, be sure the electrical acces- sory being used is turned OFF.

. When not in use, be sure to close the cap. Do not allow water to

Model "S35-D" EDITED: 2008/ 7/ 24

STORAGE

contact the outlet.

CUP HOLDERS

CAUTION

. Avoid abrupt starting and braking when the cup holder is being used to prevent spilling the drink. If the liquid is hot, it can scald you or your passenger.

. Use only soft cups in the cup holder. Hard objects can injure you in an accident.

Black plate (99,1)

SIC3494

The flap *A will be folded down when inserting a large container.

Front

To remove the inner tray for cleaning, pull it up as illustrated *1 .

Instruments and controls 2-33

Model "S35-D" EDITED: 2008/ 7/ 24

Black plate (100,1)

direct sunlight. The heat may da- mage the glasses.

To open the cup holder, pull the lid.

Rear

SUNGLASSES HOLDER

SIC3495

SIC3496

WARNING

Keep the sunglasses holder closed while driving to prevent an accident. To open the sunglasses holder, push *1 .

CAUTION

. Do not use for anything other than

glasses.

. Do not leave glasses in the sun- glasses holder while parking in

2-34 Instruments and controls

Model "S35-D" EDITED: 2008/ 7/ 24

GLOVE BOX

WARNING

Keep glove box lid closed while driving to help prevent injury in an accident or a sudden stop.

To open the glove box, pull the handle.

To close, push the lid in until the lock latches. The glove box light illuminates when the head- light switch is turned on. *A Card holder *B Back side pocket of lid *C Removable partition To remove the partition, pull it out.

SIC3497

SIC3498

Black plate (101,1)

SIC3499

CONSOLE BOX To open the console boxes, push up the knob *A and pull up the lid. To close, push the lid down until latched.

To remove the inner box (if so equipped) for cleaning or storing a large object, pull it up as illustrated *B . The inside of the console box lid is designed to be used as a card holder *C and pen holders *D .

Instruments and controls 2-35

Model "S35-D" EDITED: 2008/ 7/ 24

Black plate (102,1)

LUGGAGE FLOOR BOX (if so equipped) Type A: To open the luggage floor box, push *A . To close, push the lid until the lock latches. The net partitions can be folded to make a larger storage space.

CAUTION

To avoid damage, do not load more than 22 lbs (10 kg) of cargo into the luggage floor box.

Type B: To open the luggage floor box, pull the handle *B on the lid. To close, push the lid until the lock latches.

The luggage floor box needs to be removed when you need a spare tire. (See “FLAT TIRE” in the “6. In case of emergency” section.)

Type A

SIC3501

LUGGAGE SIDE BOX To open the luggage side box, pull up the strap.

SIC3502

Type B

SIC3514

2-36 Instruments and controls

Model "S35-D" EDITED: 2008/ 7/ 24

To stow the cargo cover, remove it from the hooks and hold until it is retracted.

To remove the cargo cover, stow the cover and pull the holder to the opposite side *2 .

WARNING

. Never put anything on the cargo cover, no matter how small. Any object on it could cause an injury in an accident or sudden stop.

. Close the cargo cover when folding

the rear seat.

. Do not leave the cargo cover in the vehicle with it disengaged from the holder.

. Properly secure all cargo with ropes or straps to help prevent it from sliding or shifting. Do not place cargo higher than the seatbacks. In a sudden stop or collision, unse- cured cargo could cause personal injury.

If the cargo cover contacts the top tether strap when it is attached to the top tether anchor, remove the cargo cover from the vehicle or secure it on the cargo floor below

Black plate (103,1)

its attachment location. If the cargo cover is not removed, it may da- mage the top tether strap during a collision. Your child could be ser- iously injured or killed in a collision if the child restraint top tether strap is damaged.

. Do not allow cargo to contact the top tether strap when it is attached to the top tether anchor. Properly secure the cargo so it does not contact the top tether strap. Cargo that is not properly secured or that contacts the top tether strap may damage the top tether strap during a collision. Your child could be seriously injured or killed in a colli- sion if the child restraint top tether strap is damaged.

Instruments and controls 2-37

Model "S35-D" EDITED: 2008/ 7/ 24

SIC3503

CARGO COVER (if so equipped) The cargo cover keeps the contents in the cargo area hidden from the outside.

To use the cargo cover, pull it out and hang both sides on the hooks *1 .

ropes and hooks.

. Unsecured luggage can become dangerous in an accident or sudden stop.

CAUTION

Do not apply a total load of more than 22 lb (10 kg) *A or 7 lb (3 kg) *B to a single hook.

Black plate (104,1)

SIC3505

COAT HOOKS (if so equipped) The coat hooks are equipped above the rear window.

CAUTION

Do not apply a total load of more than 2
lb (1 kg) to a single hook.

Model "S35-D" EDITED: 2008/ 7/ 24

LUGGAGE HOOKS (if so equipped)

SIC3504

WARNING

. Always make sure that the luggage is properly secured. Use the suitable

2-38 Instruments and controls

Black plate (105,1)

WARNING

. Drive extra carefully when the vehi- cle is loaded at or near the cargo carrying capacity, especially if the significant portion of that load is carried on the roof rack.

. Heavy loading of the roof rack has the potential to affect the vehicle stability and handling during sud- den or unusual handling maneuvers. . Roof rack load should be evenly

SIC3506

SIC3549

distributed.

UTILITY HOOK To use the utility hook on the seatback, pull it.

CAUTION

. Do not apply a total load of more

than 6 lb (3 kg) to the hook.

. Do not use the utility hook to pull the seatback to the upright and locked position. Doing so will cause the utility hook to break.

ROOF RACK (if so equipped) Secure the crossbars to the roof rail before loading. The crossbars are available from a NISSAN dealer.

Always distribute the luggage evenly on the roof rack. Do not load more than 99 lb (45 kg). Be careful that your vehicle does not exceed the Gross Vehicle Weight Rating (GVWR) or its Gross Axle Weight Rating (GAWR front and rear). The GVWR and GAWR are located on the F.M.V.S.S. or C.V.M.S.S. certification label (lo- cated on the driver’s door pillar). For more information regarding GVWR and GAWR, see “VEHICLE LOADING INFORMATION” in the “9. Technical and consumer information” section.

. Do not exceed maximum roof rack

load weight capacity.

. Properly secure all cargo with ropes or straps to help prevent it from sliding or shifting. In a sudden stop or collision, unsecured cargo could cause personal injury.

CAUTION

Use care when placing or removing items from the roof rack. If you cannot comfortably lift the items onto the roof rack from the ground, use a ladder or

Instruments and controls 2-39

Model "S35-D" EDITED: 2008/ 7/ 24

stool.

POWER WINDOWS

WINDOWS

WARNING

. Make sure that all passengers have their hands, etc. inside the vehicle while it is in motion and before closing the windows. Use the win- dow lock switch to prevent unex- pected use of the power windows.

. Do not leave children unattended inside the vehicle. They could un- knowingly activate switches or con- trols and become trapped in the window. Unattended children could become involved in serious acci- dents.

The power windows operate when the ignition switch is in the ON position, or for about 45
seconds after the ignition switch is turned to the OFF position. If the driver’s or front passenger’s door is opened during this period of about 45
seconds, power to the windows is canceled.

2-40 Instruments and controls

Black plate (106,1)

SIC3507

Main power window switch (driver’s side) 1. Window lock button 2. Driver side window 3. Rear left passenger side window 4. 5. Rear right passenger side window To open or close the window, push down *A or pull up *B the switch and hold it. The main switch (driver side switches) will open or close all the windows.

Front passenger side window

Locking passengers’ windows When the lock button *C is pushed in, only the driver side window can be opened or closed.

Model "S35-D" EDITED: 2008/ 7/ 24

Black plate (107,1)

Push it in again to cancel.

SIC3508

SIC3509

Passenger side power window switch The passenger side switch will open or close only the corresponding window. To open or close the window, push down or pull up the switch and hold it.

Automatic operation (if so equipped) The automatic operation is available for switch that has an

mark on its surface.

the

Type A: To fully open or close the window, push down or pull up the switch to the second detent and release it; the switch need not be held. The window will automatically open or close all the way. To stop the window, just push or lift the switch in the opposite direction.

Type B: To fully open the window, push down the switch to the second detent and release it; the switch need not be held. The window will automatically open all the way. To stop the window, just lift the switch. To fully close the window, push and hold the switch.

Instruments and controls 2-41

Model "S35-D" EDITED: 2008/ 7/ 24

A light push or pull on the switch will cause the window to open or close until the switch is released.

only) does not operate properly, perform the following procedure to initialize the power window system.

Auto-reverse function (if so equipped)

1. Turn the ignition switch to the ON position.

2. Close the door.

3. Open the window completely by operating

the power window switch.

4. Pull the power window switch and hold it to close the window, and then hold the switch more than 3 seconds after the window is closed completely.

5. Release the power window switch. Operate the window by the automatic function to confirm the initialization is complete.

If the power window automatic function does not operate properly after performing the pro- cedure above, have your vehicle checked by a NISSAN dealer.

WARNING

There are some small distances imme- diately before the closed position which cannot be detected. Make sure that all passengers have their hands, etc., in- side the vehicle before closing the window.

If the control unit detects something caught in the window as it is closing, the window will be immediately lowered.

The auto reverse function can be activated when the window is closed by automatic operation when the ignition switch is in the ON position or for 45 seconds after the ignition switch is turned to the OFF position.

Depending on the environment or driving conditions, the auto reverse function may be activated if an impact or load similar to something being caught in the window occurs.

If the windows do not close automatically If the power window automatic function (closing 2-42 Instruments and controls

Black plate (108,1)

MOONROOF (if so equipped)

WARNING

In an accident you could be thrown from the vehicle through an open moonroof. Always use seat belts and child restraints.

. Do not allow anyone to stand up or extend any portion of their body out of the moonroof opening while the vehicle is in motion or while the moonroof is closing.

CAUTION

. Remove water drops, snow, ice or sand from the moonroof before opening.

. Do not place any heavy object on the moonroof or surrounding area.

AUTOMATIC MOONROOF The moonroof only operates when the ignition switch is in the ON position.

The automatic moonroof is operational for about 45 seconds, even if the ignition switch is turned to the OFF position. If the driver’s door or the passenger’s door is opened during this period of

Model "S35-D" EDITED: 2008/ 7/ 24

about 45 seconds, power to the moonroof is canceled.

Sunshade The sunshade will open automatically when the moonroof is opened. However, it must be closed manually.

Black plate (109,1)

Auto reverse function

WARNING

There are some small distances imme- diately before the closed position which cannot be detected. Make sure that all passengers have their hands, etc., in- side the vehicle before closing the moonroof.

If the control unit detects something caught in the moonroof when it is closing, the moonroof will be immediately opened.

The auto reverse function can be activated when the moonroof is closed by automatic operation when the ignition switch is in the ON position or for about 45 seconds after the ignition switch is turned to the OFF position.

If the moonroof cannot be closed automatically when the auto reverse function activates due to a malfunction, push and hold the switch toward

*2 .

Depending on the environment or driving conditions, the auto reverse function may be activated if an impact or load similar to something being caught in the moonroof occurs.

Instruments and controls 2-43

Model "S35-D" EDITED: 2008/ 7/ 24

SIC3510

Sliding the moonroof To fully open or close the moonroof, push the switch toward *1 or *2 and release it; it need not be held. The roof will automatically open or close all the way. To stop the roof, push the switch in any direction while it is opening or closing.

Tilting the moonroof To tilt up, first close the moonroof by pushing the switch toward *2 . Push the switch toward again and release it; it need not be held. To tilt down the moonroof, push the switch toward *1 .

*2

Black plate (110,1)

INTERIOR LIGHTS

CAUTION

Do not use for extended periods of time with the engine stopped. This could result in a discharged battery.

MAP LIGHTS Push the light lens to turn the map light on or off.

SIC3511

Model "S35-D" EDITED: 2008/ 7/ 24

If the moonroof does not operate If the moonroof does not operate properly, perform the following procedure to initialize the moonroof operation system.

1.

If the moonroof repeatedly pushing the switch toward *2 .

is open, close it fully by

2. Push and hold the switch toward

to tilt the moonroof up.

3. Release the moonroof switch after moonroof moves slightly up and down.

4. Push and hold the switch toward

to fully tilt the moonroof down.

*2

the

*1

5. Check if normally.

the moonroof switch operates

If the moonroof does not operate properly after performing the procedure above, have your vehicle checked by a NISSAN dealer.

2-44 Instruments and controls

position

— remain on for about 15 seconds.

doors are unlocked by pushing the unlock button (on the keyfob or Intelligent Key) or the request switch (Intelligent Key system equipped model), with the ignition switch in the LOCK position

— remain on for about 15 seconds.

any door is opened and then closed with the ignition switch in the LOCK position

— remain on for about 15 seconds.

any door is opened with the ignition switch in the ACC or ON position

— remain on while the door

is opened. When the door is closed, the lights go off.

The lights will turn off after 30 minutes when the lights remain illuminated to prevent the battery from becoming dis- charged.

OFF position When the switch is in the OFF position *3 , the map lights will not illuminate, regardless of the condition.

Black plate (111,1)

SIC3513

CEILING LIGHT The ceiling light switch has three positions: ON, DOOR and OFF.

ON position When the switch is in the ON position *1 , the ceiling light will illuminate.

DOOR position When the switch is in the DOOR position *2 , the ceiling light will illuminate under the following conditions:

ignition switch is turned to the LOCK position

— remain on for about 15 seconds.

Instruments and controls 2-45

Model "S35-D" EDITED: 2008/ 7/ 24

SIC3512

The map light control switch has three positions: ON *1 , DOOR *2 and OFF *3 . The light *4
(if so equipped) will when the headlight switch is turned to the or

illuminate

position.

ON position When the switch is in the ON position *1 , the map lights will illuminate.

DOOR position When the switch is in the DOOR position *2 , the map lights will illuminate under the following conditions:

ignition switch is turned to the LOCK

.

doors are unlocked by pushing the unlock button (on the keyfob or Intelligent Key) or the request switch (Intelligent Key system equipped model), with the ignition switch in the LOCK position

— remain on for about 15 seconds.

any door is opened and then closed with the ignition switch in the LOCK position

— remain on for about 15 seconds.

any door is opened with the ignition switch in the ACC or ON position

— remain on while the door

is opened. When the door is closed, the lights go off.

The light will turn off after 30 minutes when the lights remain illuminated to prevent the battery from becoming dis- charged.

OFF position When the switch is in the OFF position *3 , the ceiling light will not illuminate, regardless of the condition.

2-46 Instruments and controls

Black plate (112,1)

VANITY MIRROR LIGHTS (if so equipped)

CARGO LIGHT (if so equipped)

SIC2064

The light on the vanity mirror will turn on when the cover on the vanity mirror is opened.

When the cover is closed, the light will turn off.

The lights will turn off after 30 minutes when the lights remain illuminated to prevent the battery from becoming dis- charged.

SIC2131A

When the switch is in the ON position *1 , the light illuminates while the lift gate is opened. When the lift gate is closed, the light will turn off. When the switch is in the OFF position *2 , the light will turn off.

The light will turn off after 30 minutes when the lights remain illuminated to prevent the battery from becoming dis- charged.

Model "S35-D" EDITED: 2008/ 7/ 24

HomeLink® UNIVERSAL TRANSCEIVER (if so equipped)

HomeLink® Universal Transceiver provides a convenient way to consolidate the functions of up to three individual hand-held transmitters into one built-in device. HomeLink® Universal Transceiver: . Will operate most Radio Frequency (RF) devices such as garage doors, gates, home and office lighting, entry door locks and security systems.

Is powered by your vehicle’s battery. No separate batteries are required. the vehicle’s battery is discharged or is dis- connected, HomeLink® will retain all pro- gramming.

If

Once HomeLink® Universal Transceiver is programmed, retain the original transmit- ter for future programming procedures (Example: new vehicle purchases). Upon sale of the programmed HomeLink® Universal Transceiver buttons should be erased for security purposes. For additional information, see “PRO- GRAMMING HomeLink®” later in this sec- tion.

the vehicle,

WARNING

. Do not use HomeLink® Universal Transceiver with any garage door opener that lacks safety stop and

reverse features as required by federal safety standards. (These standards became effective for opener models manufactured after April 1, 1982.) A garage door opener which cannot detect an object in the path of a closing garage door and then automatically stop and reverse, does not meet current federal safety standards. Using a garage door opener without these features in- creases the risk of serious injury or death.

. During programming procedure, your garage door or security gate may open or close. Make sure that people and objects are clear of the garage door, gate, etc. that you are programming.

. Your vehicle’s engine should be turned off while programming HomeLink® Universal Transceiver.

PROGRAMMING HomeLink® To program your HomeLink® Transceiver to operate a garage door, gate, or entry door opener, home or office lighting, you need to be at the same location as the device. Note: Garage door openers (manufactured after

Black plate (113,1)

1996) have “rolling code protection”. To pro- gram a garage door opener equipped with “rolling code protection”; you will need to use a ladder to get up to the garage door opener motor to be able to access the “smart or learn” program button.

Instruments and controls 2-47

Model "S35-D" EDITED: 2008/ 7/ 24

Black plate (114,1)

5.

activate. If the indicator light on HomeLink® blinks rapidly for two seconds and then turns solid, HomeLink® has picked up a “rolling code” garage door opener signal. You will need to proceed with the next steps to train Home- Link®, completing the programming may require a ladder and another person for convenience.

6. Push and release the program button located on the garage door opener’s motor to activate the “training mode”. This button is usually located near the antenna wire that hangs down from the motor. the wire originates from under a light lens, you will need to remove the lens to access the training button.

If

NOTE: Once you have pushed and released the training button on the garage door open- er’s motor and the “training light” is lit, you have 30 seconds in which to perform step 7. For convenience, use the help of a second person to assist when performing this step. 7. Quickly (within 30 seconds of pushing and releasing the garage door opener training button) and firmly push and release the HomeLink® button you’ve just programmed. Push and release the HomeLink® button up

Model "S35-D" EDITED: 2008/ 7/ 24

SIC3182

SIC3183

1. To begin, push and hold the 2 outer Home- Link® buttons (to clear the memory) until the indicator light *A blinks (after 20 seconds). Release both buttons.

2. Position the end of the hand-held transmitter 1-3 inches away from the HomeLink® sur- face.

2-48 Instruments and controls

3. Using both hands, simultaneously push and hold both the HomeLink® button you want to program and the hand-held transmitter button. DO NOT release the buttons until step 4 has been completed.

4. Hold down both buttons until the indicator light on HomeLink® flashes, changing from a “slow blink” to a “rapid blink”. This could take up to 90 seconds. When the indicator light blinks rapidly, both buttons may be released. The rapidly flashing light indicates successful programming. To activate the garage door or other programmed device, push and hold the programmed HomeLink® button - releasing when the device begins to

Black plate (115,1)

to three times to complete the training.

8. Your HomeLink® button should now be programmed. To program the remaining HomeLink® buttons for additional door or gate openers, follow steps 2 through 8 only.

NOTE: Do not repeat step 1 unless you want to “clear” all previously programmed Home- Link® buttons.

If you have any questions or are having difficulty programming your HomeLink® buttons, please to the HomeLink® web site at: www. refer homelink.com or call 1-800-355-3515.

to 1992, D.O.C.

PROGRAMMING HomeLink® FOR CA- NADIAN CUSTOMERS Prior regulations required hand-held transmitters to stop transmitting after 2 seconds. To program your hand-held trans- mitter to HomeLink®, continue to push and hold the HomeLink® button (note steps 2 through 4
under “Programming HomeLink®”) while you push and re-push (“cycle”) your hand-held transmitter every 2 seconds until the indicator light flashes rapidly (indicating successful pro- gramming).

NOTE: If programming a garage door opener, etc., it is advised to unplug the device during

the “cycling” process to prevent possible damage to the garage door opener com- ponents.

programmed within that time, try holding the transmitter in another position - keeping the indicator light in view at all times.

OPERATING THE HomeLink® UNIVER- SAL TRANSCEIVER HomeLink® Universal Transceiver (once pro- grammed) may now be used to activate the garage door, etc. To operate, simply push the appropriate programmed HomeLink® Universal Transceiver button. The red indicator light will illuminate while the signal is being transmitted.

PROGRAMMING TROUBLE-DIAGNO- SIS If HomeLink® does not quickly learn the hand- held transmitter information:

replace the hand-held transmitter batteries with new batteries.

position the hand-held transmitter with its battery area facing away from the Home- Link® surface. push and hold both the HomeLink® and hand-held transmitter buttons without inter- ruption.

position the hand-held transmitter 2 to 5 in (50 to 127 mm) away from the HomeLink® surface. Hold the transmitter in that position for up to 15 seconds. If HomeLink® is not

If you continue to have programming difficulties, please contact the NISSAN Consumer Affairs Department. The phone numbers are located in the Foreword of this Owner’s Manual.

CLEARING THE PROGRAMMED IN- FORMATION Individual buttons cannot be cleared, however to clear all programming, push and hold the two outside buttons and release when the indicator light begins to flash (in approximately 20
seconds).

REPROGRAMMING A SINGLE HomeLink® BUTTON To reprogram a HomeLink® Universal Transcei- ver button, complete the following. 1. Push and hold the desired HomeLink® button. Do not release the button until step 4 has been completed.

2. When the indicator light begins to flash slowly (after 20 seconds), position the hand-held transmitter 2 to 5 in (50 to 127
mm) away from the HomeLink® surface.

3. Push and hold the hand-held transmitter

button.

Instruments and controls 2-49

Model "S35-D" EDITED: 2008/ 7/ 24

Black plate (116,1)

The transmitter has been tested and complies with FCC and DOC/MDC rules. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the device.

DOC: ISTC 1763K1313

FCC I.D.: CB2V67690

4. The HomeLink® indicator light will flash, first slowly and then rapidly. When the indicator light begins to flash rapidly, release both buttons.

The HomeLink® Universal Transceiver button has now been reprogrammed. The new device can be activated by pushing the HomeLink® button that was just programmed. This procedure will not affect any other programmed HomeLink® buttons.

IF YOUR VEHICLE IS STOLEN If your vehicle is stolen, you should change the codes of any non-rolling code device that has been programmed into HomeLink®. Consult the Owner’s Manual of each device or call the manufacturer or dealer of those devices for additional information.

When your vehicle is recovered, you will need to reprogram the HomeLink® Univer- sal Transceiver with your new transmitter information.

FCC Notice:

This device complies with FCC rules part 15. Operation is subject to the following two conditions: (1) This device may not cause harmful interference and (2) This device must accept any interference that may be received, including interference that may cause undesired operation. 2-50 Instruments and controls

Model "S35-D" EDITED: 2008/ 7/ 24

Black plate (10,1)

3 Pre-driving checks and adjustments

Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2
NISSAN Vehicle Immobilizer System keys . . . . . . . . . . . . 3-2
Intelligent Keys (if so equipped) . . . . . . . . . . . . . . . . . . . . . . . . . 3-3
Doors. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4
Locking with key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4
Locking with inside lock knob . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4
Locking with power door lock switch . . . . . . . . . . . . . . . . . . 3-5
Automatic door locks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5
Child safety rear door lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-6
Remote keyless entry system (if so equipped) . . . . . . . . . . . 3-6
How to use remote keyless entry system . . . . . . . . . . . . . 3-7
Intelligent Key system (if so equipped) . . . . . . . . . . . . . . . . . . . . 3-8
Intelligent Key operating range . . . . . . . . . . . . . . . . . . . . . . . . 3-10
Door locks/unlocks precaution . . . . . . . . . . . . . . . . . . . . . . . . 3-11
Intelligent Key operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-11

Warning lights and audible reminders . . . . . . . . . . . . . . . 3-13
Troubleshooting guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-14
How to use remote keyless entry function . . . . . . . . . . 3-16
Hood . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-20
Lift gate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-21
Lift gate release . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-22
Fuel-filler door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-22
Opening the fuel-filler door. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-22
Fuel-filler cap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-22
Steering wheel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-24
Tilt operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-24
Sun visors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-24
Mirrors. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-25
Inside mirror. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-25
Outside mirrors. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-26

Model "S35-D" EDITED: 2008/ 6/ 3

KEYS

A key number plate is supplied with your keys. Record the key number and keep it in a safe place (such as your wallet), not in the vehicle. If you lose your keys, see a NISSAN dealer for duplicates by using the key number. NISSAN does not record any key numbers so it is very important to keep track of your key number plate.

A key number is only necessary when you have lost all keys and do not have one to duplicate from. If you still have a key, this key can be duplicated by a NISSAN dealer.

Black plate (118,1)

duplicate your existing key. As many as 5 keys can be used with one vehicle. You should bring all the registered keys that you have to a NISSAN dealer for registration. This is because the registration process will erase the memory of all key codes previously registered into the NISSAN Vehicle Immobilizer System. After the registration process, these components will only recognize keys coded into the NISSAN Vehicle Immobilizer System during registration. Any key that is not given to your dealer at the time of registration will no longer be able to start your vehicle.

SPA2405

CAUTION

Do not allow the NISSAN Vehicle Im- mobilizer System key, which contains an electrical transponder, to come in contact with salt water. This could cause the system to malfunction.

1. Master key (2) 2. Key number plate (1) NISSAN VEHICLE IMMOBILIZER SYS- TEM KEYS Your vehicle can only be driven with the master keys which are registered to the NISSAN Vehicle Immobilizer System components in your vehicle. These keys have a transponder chip in the key head.

Never leave these keys in the vehicle.

Additional or replacement keys:

If you still have a key, the key number is not necessary when you need extra NISSAN Vehicle Immobilizer System keys. Your dealer can

3-2 Pre-driving checks and adjustments

Model "S35-D" EDITED: 2008/ 7/ 24

nents when registering new keys, be sure to take all Intelligent Keys that you have to the NISSAN dealer.

CAUTION

. Do not allow the Intelligent Key, which contains electrical compo- nents, to come into contact with water or salt water. This could affect the system function.

. Do not drop the Intelligent Key. . Do not strike the Intelligent Key

sharply against another object.

. Do not place the Intelligent Key for an extended period in an area where temperatures exceed 1408F (608C). . Do not attach the Intelligent Key with a key holder that contains a magnet.

. Do not place the Intelligent Key near equipment that produces a mag- netic field, such as a TV, audio equipment and personal computers.

SPA2406

Intelligent Key (2)

1. 2. Mechanical key (inside Intelligent Key) (2) 3. Key number plate (1) INTELLIGENT KEYS (if so equipped) Your vehicle can only be driven with the Intelligent Keys which are registered to your vehicle’s Intelligent Key system components and NISSAN Vehicle Immobilizer System compo- nents. As many as 4 Intelligent Keys can be registered and used with one vehicle. The new keys must be registered by a NISSAN dealer prior to use with the Intelligent Key system and NISSAN Vehicle Immobilizer System of your vehicle. Since the registration process requires erasing all memory in the Intelligent Key compo-

Black plate (119,1)

SPA2033

Mechanical key To remove the mechanical key, release the lock knob at the back of the Intelligent Key.

To install the mechanical key, firmly insert it into the Intelligent Key until the lock knob returns to the lock position.

Use the mechanical key to lock or unlock the doors. (See “DOORS” later in this section.)

CAUTION

Always carry the mechanical key in- stalled in the Intelligent Key.

Pre-driving checks and adjustments 3-3

Model "S35-D" EDITED: 2008/ 7/ 24

DOORS

WARNING

. Always have the doors locked while driving. Along with the use of seat belts, this provides greater safety in the event of an accident by helping to prevent persons from being thrown from the vehicle. This also helps keep children and others from unintentionally opening the doors, and will help keep out intruders.

. Before opening any door, always look for and avoid oncoming traffic. . Do not leave children unattended inside the vehicle. They could un- knowingly activate switches or con- trols. Unattended children could become involved in serious acci- dents.

3-4 Pre-driving checks and adjustments

Black plate (120,1)

SPA2394

SPA1814

LOCKING WITH KEY The power door lock system allows you to lock or unlock all doors simultaneously.

Turning the driver’s door key cylinder to the front of the vehicle *1 will lock all doors. Turning the driver’s door key cylinder once to the rear of the vehicle *2 will unlock the driver’s door. After returning the key to the neutral position, turning it to the rear again within 5 seconds will unlock all doors and the lift gate.

LOCKING WITH INSIDE LOCK KNOB To lock the door without the key, move the inside lock knob to the lock position *1
then close the door.

To unlock, move the inside lock knob to the unlock position *2 . When locking the door without a key, be sure not to leave the key inside the vehicle.

Model "S35-D" EDITED: 2008/ 7/ 24

Lockout protection When the power door lock switch (driver or front passenger) is moved to the lock position with the key in the ignition switch or the Intelligent Key in the vehicle and any door open, all doors will lock and unlock automatically.

This function helps to prevent the keys from being accidentally locked inside the vehicle.

AUTOMATIC DOOR LOCKS . All doors will be locked automatically when the vehicle speed reaches 15 MPH (24
km/h).

. All doors will be unlocked automatically when the ignition switch is turned to the ACC position.

The automatic lock and unlock functions can be deactivated or activated indepen- dently of each other.

To deactivate or activate the automatic lock or unlock system, perform the following procedure.

1. Close all doors.

2. Turn the ignition switch to the ON position.

3. Do one of the following within 20 seconds of

performing step 2.

To change AUTO UNLOCK settings: push and hold the power door lock

SPA2300

LOCKING WITH POWER DOOR LOCK SWITCH Operating the power door lock switch will lock or unlock all the doors. The switches are located on the driver’s and front passenger’s door armrests.

To lock the doors, push the power door lock switch to the lock position *1 with the driver’s or front passenger’s door open, then close the door.

When locking the door this way, be sure not to leave the key inside the vehicle.

To unlock the doors, push the power door lock switch to the unlock position *2 .

Black plate (121,1)

switch to the for more than 5 seconds.

position (UNLOCK)

To change AUTO LOCK settings: push and hold the power door lock switch to the position (LOCK) for more than 5 seconds.

4. When activated,

the hazard indicator will flash twice. When deactivated, the hazard indicator will flash once.

5. The ignition must be placed in the OFF and ON position again between each setting change.

Pre-driving checks and adjustments 3-5

Model "S35-D" EDITED: 2008/ 7/ 24

REMOTE KEYLESS ENTRY SYSTEM (if so equipped)

It is possible to lock/unlock all doors (including the lift gate), and activate the panic alarm by using the keyfob from outside the vehicle. Before locking the doors, make sure the key is not left in the vehicle. The keyfob can operate at a distance of approximately 33 ft (10 m) from the vehicle. (The effective distance depends upon the conditions around the vehicle.) As many as 5 keyfobs can be used with one vehicle. For information concerning the pur- chase and use of additional keyfobs, contact a NISSAN dealer.

The keyfob will not function: . When the keyfob is not within the opera-

tional range.

. When the doors are open or not closed

securely.

. When the key is in the ignition switch. . When the battery is discharged.

CAUTION

The following conditions or occur- rences will damage the keyfob. . Do not allow the keyfob to become

wet.

. Do not drop the keyfob.

Black plate (122,1)

. Do not strike the keyfob sharply

against another object.

. Do not place the keyfob for an extended period in an area where temperatures exceed 1408F (608C). If a keyfob is lost or stolen, NISSAN recommends erasing the ID code of that keyfob. This will prevent the keyfob from unauthorized use to unlock the vehicle. For information regarding the erasing procedure, please contact a NISSAN dealer.

If the indicator light on the keyfob does not illuminate when pushing the buttons, the keyfob battery may be discharged.

For information regarding the replacement of a battery, see “BATTERY REPLACEMENT” in the “8. Maintenance and do-it-yourself” section.

Model "S35-D" EDITED: 2008/ 7/ 24

SPA2037

CHILD SAFETY REAR DOOR LOCK Child safety rear door locks help prevent the rear doors from being opened accidentally, espe- cially when small children are in the vehicle.

When the levers are in the lock position *1 , the rear doors can be opened only from the outside.

To disengage, move the levers to the unlock position *2 .

3-6 Pre-driving checks and adjustments

Black plate (123,1)

. Any door or lift gate is opened.

The ignition switch is turned to the ON position.

The interior light can be turned off without waiting for 15 seconds by turning the ignition switch to the ON position or by locking the doors with the keyfob.

Using the panic alarm If you are near your vehicle and feel threatened, you may activate the alarm to call attention by pushing and holding the PANIC button on the keyfob for longer than 1 second (with the key removed from the ignition switch).

The theft warning alarm and headlights will stay on for 25 seconds.

5. The hazard indicator flashes twice and the

horn chirps once. . When the LOCK

button is pushed with all doors locked, the hazard indicator flashes twice and the horn chirps once as a reminder that the doors are already locked. . Operate the door handles to confirm that the

doors have been securely locked.

Unlocking doors 1. Push the UNLOCK

button on the

keyfob once.

The driver’s door unlocks.

The hazard indicator flashes once if all doors are completely closed.

The interior light illuminates and the light timer activates for 15 seconds when the switch is in the DOOR position.

The panic alarm stops when:

It has run for 25 seconds, or

2. Push the UNLOCK

button again within

5 seconds. . All the doors and the lift gate unlock.

The hazard indicator flashes once if all doors are completely closed.

All doors will be locked automatically unless one of the following operations is performed within 1
minute of pushing the UNLOCK

button.

The LOCK

button or the UNLOCK

button is pushed, or

The PANIC keyfob for longer than 1 second.

button is pushed on the

Pre-driving checks and adjustments 3-7

Model "S35-D" EDITED: 2008/ 7/ 24

SPA2416

*1 LOCK button *2 UNLOCK button *3 PANIC button HOW TO USE REMOTE KEYLESS ENTRY SYSTEM Locking doors 1. Remove the key from the ignition switch.

2. Close all the doors.

3. Push the LOCK

button on the keyfob.

4. All the doors will lock.

All of the doors will

lock when the LOCK button is pushed even though a door

remains open.

Black plate (124,1)

INTELLIGENT KEY SYSTEM (if so equipped)

WARNING

. Radio waves could adversely affect electric medical equipment. Those who use a pacemaker should con- tact the electric medical equipment manufacturer for the possible influ- ences before use.

The Intelligent Key transmits radio waves when the buttons are pushed. The FAA advises that the radio waves may affect aircraft na- vigation and communication sys- t e m s . D o n o t o p e r a t e t h e Intelligent Key while on an airplane. Make sure the buttons are not operated unintentionally when the unit is stored during a flight.

The Intelligent Key system can operate all the door locks using the remote controller function or pushing the request switch on the vehicle without taking the key out from a pocket or purse. The operating environment and/or condi- tions may affect the Intelligent Key system operation.

Be sure to read the following before using the Intelligent Key system.

Model "S35-D" EDITED: 2008/ 7/ 24

SPA1260

is pushed, neither the hazard indicator nor the horn operates.

Switching procedure:

Push the LOCK buttons simultaneously for more than 2 seconds to switch from one mode to the other.

and UNLOCK