2008 Nissan Rogue Owners Manual

Push up or down the tuning switch for more than 1.5 seconds to seek the next or previous radio station.

APS (Automatic Program Search) FF, APS REW (CD or CD changer):

Push up or down the tuning switch for less than 1.5 seconds to return to the beginning of the present program or skip to the next program. Push several times to skip back or skip through programs.

This system searches for the blank intervals If there is a blank interval between selections. within one program or there is no interval between programs, the system may not stop in the desired or expected location.

FOLDER change (CD changer - CD with MP3 or WMA):

Push up or down the tuning switch for more than 1.5 seconds to change the folders (if there are any folders).

DISC change (CD changer - CD without MP3 or WMA):

Push up or down the tuning switch for more than 1.5 seconds to change the playing disc up or down.

Heater, air conditioner, audio and phone systems 4-23

Model "S35-D" EDITED: 2007/ 7/ 3

SAA1780

Type B

Tuning switch

1. 2. VOLUME control switch 3. SOURCE select switch 4. POWER on/off switch STEERING WHEEL SWITCH FOR AUDIO CONTROL (if so equipped) The audio system can be operated using the controls on the steering wheel.

POWER on/off switch (Type B) With the ignition switch turned to the ACC or ON position, push the POWER on/off switch to turn the audio system on or off.

CAUTION

. Be sure that antenna is removed before the vehicle enters an auto- matic car wash.

. Be sure to fold down the antenna before the vehicle enters a garage with a low ceiling.

SAA1236

ANTENNA Adjust the antenna angle for the best reception.

To remove the antenna, hold the bottom of the antenna and turn it counterclockwise.

4-24 Heater, air conditioner, audio and phone systems

Black plate (168,1)

CAR PHONE OR CB RADIO

When installing a car phone or a CB radio in your NISSAN, be sure to observe the following precautions, otherwise the new equipment may adversely affect the electronic control modules and electronic control system harness.

WARNING

. A cellular telephone should not be used while driving so full attention may be given to vehicle operation. Some jurisdictions prohibit the use of cellular telephones while driving.

If you must make a call while your vehicle is in motion, the hands-free cellular phone operational mode (if so equipped) is highly recom- mended. Exercise extreme caution at all times so full attention may be given to vehicle operation.

If a conversation in a moving vehicle requires you to take notes, pull off the road to a safe location and stop your vehicle before doing so.

Model "S35-D" EDITED: 2007/ 7/ 3

Black plate (169,1)

BLUETOOTH® HANDS-FREE PHONE SYSTEM WITH NISSAN VOICE RECOGNITION (if so equipped)

CAUTION

WARNING

. Keep the antenna as far away as possible from the electronic control modules.

. Keep the antenna wire more than 8
in (20 cm) away from the electronic control system harness. Do not route the antenna wire next to any harness.

. Adjust the antenna standing-wave ratio as recommended by the man- ufacturer.

. Connect the ground wire from the

CB radio chassis to the body.

. For details, consult a NISSAN deal-

er.

. Use a phone after stopping your vehicle in a safe location. If you have to use a phone while driving, exercise extreme caution at all times so full attention may be given to vehicle operation.

If you find yourself unable to devote full attention to vehicle operation while talking on the phone, pull off the road to a safe location and stop your vehicle before doing so.

CAUTION

To avoid discharging the vehicle bat- tery, use a phone after starting the engine.

Heater, air conditioner, audio and phone systems 4-25

Model "S35-D" EDITED: 2007/ 7/ 3

Black plate (170,1)

list.

. You will not be able to use a hands-free

phone under the following conditions:

— Your vehicle is outside of

the cellular

service area.

— Your vehicle is in an area where it

is difficult to receive a cellular signal; such as in a tunnel, in an underground parking garage, near a tall building or in a mountainous area.

— Your cellular phone is locked to prevent it

from being dialed.

. When the radio wave condition is not ideal it may be to hear the other person’s voice

or ambient sound is too loud, difficult during a call.

Immediately after turned to the ON position, impossible to receive a call period of time.

the ignition switch is it may be for a short

. Do not place the cellular phone in an area surrounded by metal or far away from the in- vehicle phone module to prevent tone quality degradation and wireless connection dis- ruption.

. While a cellular phone is connected through the

the Bluetooth® wireless connection,

Model "S35-D" EDITED: 2007/ 7/ 3

Your NISSAN is equipped with the Bluetooth® Hands-Free Phone System. If you are an owner of a Bluetooth® enabled cellular phone, you can set up the wireless connection between your cellular phone and the in-vehicle phone module. With Bluetooth® wireless technology, you can make or receive a hands-free telephone call with your cellular phone in the vehicle.

Once your cellular phone is paired to the in- vehicle phone module, no other phone connect- ing procedure is required. Your phone is automatically connected with the in-vehicle phone module when the ignition switch is turned to the ON position with the registered cellular phone turned on and carried in the vehicle.

SAA1781

You can register up to 5 different Bluetooth® cellular phones to the in-vehicle phone module. However, you can talk on only one cellular phone at a time. Before using the Bluetooth® Hands-Free Phone System, refer to the following notes. . Set up the wireless connection between a cellular phone and the in-vehicle phone module before using the Bluetooth ® Hands-Free Phone System.

. Some Bluetooth® enabled cellular phones may not be recognized by the in-vehicle phone module. Please visit www.nissanusa. com/bluetooth for a recommended phone

4-26 Heater, air conditioner, audio and phone systems

Black plate (171,1)

the cellular phone may

battery power of discharge quicker than usual. If the Bluetooth® Hands-Free Phone System seems to be malfunctioning, please refer to “Troubleshooting guide” later in this section. You can also visit www.nissanusa.com/blue- tooth for troubleshooting help.

. Some cellular phones or other devices may cause interference or a buzzing noise to come from the audio system speakers. Storing the device in a different location may reduce or eliminate the noise.

. Refer to the cellular phone Owner’s Manual regarding the telephone charges, cellular phone antenna and body, etc.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interfer- ence received, including interference that may cause undesired operation.

FCC Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 8 in (20
cm) between the radiator and your body. This Transmitter must not be co-located or operating

in conjunction with any other antenna or transmitter.

command. Otherwise, the command will not be received properly.

USING SYSTEM

The NISSAN Voice Recognition system allows hands-free operation of the Bluetooth® Hands- Free Phone System.

If the vehicle is in motion, some commands may not be available so full attention may be given to vehicle operation.

Initialization When the ignition switch is turned to the ON position, NISSAN Voice Recognition is initia- lized, which takes a few seconds. button is pushed before the initialization com- pletes, the system will announce “Hands-free phone system not ready” and will not react to voice commands.

If the

Operating tips To get the best performance out of the NISSAN Voice Recognition system, observe the follow- ing: . Keep the interior of the vehicle as quiet as possible. Close the windows to eliminate surrounding noises (traffic noises, vibration sounds, etc.), which may prevent the system from recognizing voice commands correctly. . Wait until the tone sounds before speaking a

. Start speaking a command within 5 seconds

after the tone sounds.

. Speak in a natural voice without pausing

between words.

Giving voice commands To operate NISSAN Voice Recognition, push and release the button located on the steering wheel. After the tone sounds, speak a command.

The command given is picked up by the microphone, and voice feedback is given when the command is accepted.

If you need to hear the available commands for the current menu again, say “Help” and the system will repeat them.

If a command is not recognized, the system announces, “Command not recognized. Please try again.” Repeat the command in a clear voice.

If you want to go back to the previous command, you can say “Go back” or “Correction” anytime the system is waiting for a response.

. You can cancel a command when the system is waiting for a response by saying,

Heater, air conditioner, audio and phone systems 4-27

Model "S35-D" EDITED: 2007/ 7/ 3

“Cancel” or “Quit.” The system announces “Cancel” and ends the voice recognition (VR) session. You can also push the button on the steering wheel at any time. Whenever the VR session is canceled, a double beep sounds to indicate you have exited the system.

If you want to adjust the volume of the voice feedback, push the volume control switches (+ or −) on the steering wheel while being provided with feedback. You can also use the radio volume control knob.

How to say numbers:

NISSAN Voice Recognition requires a certain way to speak numbers in voice commands. Refer to the following rules and examples: . Either “zero” or “oh” can be used for “0”.

Example: 1-800-662-6200

—“One eight oh oh six six two six two oh

oh”, or

—“One eight zero zero six six two six two oh

oh”

. Words can be used for the first 4 digits

places only.

Example: 1-800-662-6200

—“One eight hundred six six two six two oh

oh”,

—NOT “One eight hundred six six two sixty

two hundred, and

—NOT “One eight oh oh six six two sixty two

hundred.

. Numbers can be spoken in small groups. The system will prompt you to continuing entering digits, if desired.

Example: 1-800-662-6200

—“One eight oh oh”

The system repeats the numbers and prompts you to enter more.

—“six six two”

The system repeats the numbers and prompts you to enter more.

—“six two oh oh”

. You can say “Star” for * and “Pound” for # at anytime in any position of the phone number.

Example: 1-555-1212 *123

—“One five five five one two one two star

one two three”

NOTE: For best results, say phone numbers as single digits.

4-28 Heater, air conditioner, audio and phone systems

Black plate (172,1)

SAA1782

Control buttons The control buttons for the Bluetooth® Hands- Free Phone System are located on the steering wheel.

TALK/PHONE SEND

Push the or answer an incoming call.

button to initiate a VR session

You can also use the button to skip through system feedback and to enter commands during a call. (See “List of voice commands” later in this section and “” later in this section for more information.)

Model "S35-D" EDITED: 2007/ 7/ 3

Black plate (173,1)

PHONE END

Push the or end a call.

button to cancel a VR session

Getting started The following procedures will help you get started using the Bluetooth® Hands-Free Phone System with NISSAN Voice Recognition. For additional command options, see “List of voice commands” later in this section.

Choosing a language You can interact with the Bluetooth® Hands-Free Phone System using English, Spanish or French.

To change the language, perform the following.

1. Push and hold the

button for more than

5 seconds.

2. The system announces: “Press the PHONE SEND ( the hands-free phone system to enter the speaker adapta- tion mode or press the PHONE END ( button to select a different language.”

) button for

3. Press the

button.

For information on speaker adaptation, see “SPEAKER ADAPTATION (SA) MODE” later in this section.

4. The system announces the current language and gives you the option to change the

language to Spanish (in Spanish) or French in French). Use the following chart to select the language.

NOTE: You must push the button within 5 seconds to change the language.

button or the

Current lan-

guage

Press

(TALK/PHONE SEND) to select

English

Spanish

French

Spanish

English

English

Press

(PHONE END)

to select

French

French

Spanish

5.

If you decide not to change the language, do not push either button. After 5 seconds, the VR session will end, and the language will not be changed.

Pairing procedure NOTE: The pairing procedure must be performed when the vehicle is stationary. the vehicle starts moving during the proce- dure, the procedure will be cancelled.

If

1. Push the

button on the steering wheel. The system announces the available com- mands.

2. Say: “Setup” *A . The system acknowl- edges the command and announces the next set of available commands.

3. Say: “Pair phone” *B . The system acknowl- edges the command and announces the next set of available commands.

4. Say: “New phone” *C . The system ac- knowledges the command and asks you to initiate pairing from the phone handset *D . When you are asked to enter a PIN code for pairing your Bluetooth® cellular phone, operate it to enter the code “1234”. The code is always “1234” regardless of the number of phones paired.

The pairing procedure of the cellular phone Heater, air conditioner, audio and phone systems 4-29

Model "S35-D" EDITED: 2007/ 7/ 3

varies according to each cellular phone. See the cellular phone Owner’s Manual for details. You can also visit www.nissanusa. com/bluetooth for instructions on pairing NISSAN recommended cellular phones.

5. The system asks you to say a name for the

phone *E . If the name is too long or too short, the system tells you, then prompts you for a name again.

Also, if more than one phone is paired and the name sounds too much like a name already used, then prompts you for a name again.

the system tells you,

6. The system asks you to assign a priority level *F . The priority level determines which phone is active when more than one paired Bluetooth® phone is in the vehicle. Follow the instructions provided by the system or see “Setup” later in this section for more information on changing priorities.

7. The system will ask if you would like to select a custom ringtone *G . Follow the instructions provided by the system or see “Setup” later in this section for more information on selecting ringtones.

Making a call by entering a phone number

1. Push the

button on steering wheel. A

tone will sound.

2. Say: “Call” *A . The system acknowledges the command and announces the next set of available commands.

3. Say the number you wish to call *B . For example, 555-1212 can be said as “five five five one two one two.” (See “How to say numbers” earlier in this section for more information.)

4. When you have finished speaking the phone the system repeats it back and

number, announces the available commands.

5. Say: “Dial” *C . The system acknowledges

the command and makes the call.

For additional command options, see “List of voice commands” later in this section.

4-30 Heater, air conditioner, audio and phone systems

Black plate (174,1)

Receiving a call When you hear the ringtone, push the button on the steering wheel.

Once the call has ended, push the on the steering wheel.

button

NOTE: If you do not wish to take the call when you hear the ringtone, push the button on the steering wheel to reject the call.

For additional command options, see “List of voice commands” later in this section.

List of voice commands

button on When you push and release the the steering wheel, you can choose from the commands on the Main Menu. The following pages describe these commands and the commands in each sub-menu.

Remember to wait for the tone before speaking.

You can say “Help” to hear the list of commands

Model "S35-D" EDITED: 2007/ 7/ 3

currently available anytime the system is waiting for a response.

Call

If you want to end an action without completing it, you can say “Cancel” or “Quit” at anytime the system is waiting for a response. The system will end the VR session. Whenever the VR session is canceled, a double beep is played to indicate you have exited the system.

If you want to go back to the previous command, you can say “Go back” or “Correction” anytime the system is waiting for a response.

When you get used to the menus in the system, you can talk ahead by saying more than one command at a time. For example, say, “Call five five five one two one two” or “Memo pad record.”

Also, when you get used to the system responses, you can skip ahead to the tone by pressing the button on the steering wheel. However, if you press the button when the system is waiting for a response from you it will end the VR session.

(speak name) *A If you have stored entries in the Phone Book, you can dial a number associated with a name and location.

See “Phone book” later in this section to learn how to store entries.

When prompted by the system, say the name of the phone book entry you wish to call. The system acknowledges the name.

If there are multiple locations associated with the name, the system asks you to choose the location.

Once you have confirmed the name and location, the system begins the call. (speak digits) *B When prompted by the system, say the number you wish to call. (See “How to say numbers”

Black plate (175,1)

earlier in this section and “Making a call by entering a phone number” earlier in this section for more details.) “Redial” *C Use the Redial command to call the last number that was dialed within the vehicle.

NOTE: The system will not redial the last number dialed by the handset keypad.

The system acknowledges the command, re- peats the number and begins dialing.

If a redial number does not exist, the system announces, “There is no number to redial” and ends the VR session. “Call back”*D Use the Call Back command to dial the number of the last incoming call within the vehicle.

The system acknowledges the command, re- peats the number and begins dialing.

If a call back number does not exist, the system announces, “There is no number to call back” and ends the VR session.

During a call

During a call there are several command options available. Push the button on the steering

Heater, air conditioner, audio and phone systems 4-31

Model "S35-D" EDITED: 2007/ 7/ 3

wheel to mute the receiving voice and enter commands.

“Help” — The system announces the avail- able commands.

“Go back/Correction” — The system an- nounces “Go back,” ends the VR session and returns to the call.

“Cancel/Quit” — The system announces “Cancel,” ends the VR session and returns to the call.

“Send/Enter/Call/Dial” — Use the Send command to enter numbers during a call. For example, if you were directed to dial an extension by an automated system:

Say: “Send one two three four.”

The system acknowledges the command and sends the tones associated with the numbers. The system then ends the VR session and returns to the call.

“Transfer Call” — Use the Transfer Call command to transfer from the Bluetooth® Hands-Free Phone System to the cellular phone when privacy is desired.

the call

The system announces, “Transfer call. Call transferred to privacy mode.” The system then ends the VR session.

You can also issue the Transfer Call

command again to return to a hands-free call through the vehicle.

“Mute” — Use the Mute command to mute your voice so the other party cannot hear it. Use the mute command again to unmute your voice.

NOTE: If a call is ended or the cellular phone network connection is lost while the Mute feature is on, the Mute feature may need to be reset to “off” for the next call so the other party can hear your voice.

Phone book NOTE: Phone book commands are not available when the vehicle is moving.

The Phone Book stores up to 40 names for each phone paired with the system. Each name can have up to 4 locations/phone numbers asso- ciated with it.

4-32 Heater, air conditioner, audio and phone systems

Black plate (176,1)

NOTE: Each phone has its own separate phone book. You cannot access Phone A’s phone book if you are currently connected with Phone B. “New Entry” *A Use the New Entry command to store a new name in the system.

When prompted by the system, say the name you would like to give the new entry.

For example, say: “Mary.”

If the name is too long or too short, the system tells you, then prompts you for a name again.

Also, if the name sounds too much like a name already stored, then prompts you for a name again.

the system tells you,

Once the system accepts the name and you confirm it the system asks for a location (Home, Office, Mobile or Other).

is correct,

For example, say: “Home.”

The system acknowledges the location.

The system will ask you to say a phone number or to transfer a phone number stored in the cellular phone’s memory.

To enter a phone number by voice command:

Model "S35-D" EDITED: 2007/ 7/ 3

Black plate (177,1)

For example, say: “five five five one two one two.” (See “How to say numbers” earlier in this section for more information.)

To transfer a phone number stored in the cellular phone’s memory (if so equipped):

Say “Transfer entry.” The system acknowledges the command and asks you to initiate the transfer from the phone handset. The new contact phone number will be transferred from the cellular phone via the Bluetooth® commu- nication link.

The transfer procedure varies according to each cellular phone. See the cellular phone Owner’s for details. You can also visit www. Manual nissanusa.com/bluetooth for instructions on transferring phone numbers from NISSAN re- commended cellular phones.

The system repeats the number and prompts you for the next command. When you have finished entering numbers, choose “Store.”

location and The system confirms the name, number. The system then asks if you would like to store another location for the same name. If you do not wish to store another location, the system ends the VR session. “Edit” *B Use the Edit command to alter an existing phone book entry or to add a 2nd, 3rd or 4th phone

number to an existing entry.

commended cellular phones.

When prompted by the system, say the name of the entry you wish to edit.

The system acknowledges the name and asks you for the location you would like to edit.

Say the name of acknowledges the location.

the location. The system

The system will ask you to say a phone number or to transfer a phone number stored in the cellular phone’s memory.

To enter a phone number by voice command:

For example, say: “five five five one two one two.” (See “How to say numbers” earlier in this section for more information.)

To transfer a phone number stored in the cellular phone’s memory (if so equipped):

Say “Transfer entry.” The system acknowledges the command and asks you to initiate the transfer from the phone handset. The new contact phone number will be transferred from the cellular phone via the Bluetooth® commu- nication link.

The transfer procedure varies according to each cellular phone. See the cellular phone Owner’s for details. You can also visit www. Manual nissanusa.com/bluetooth for instructions on transferring phone numbers from NISSAN re-

The system repeats the number and prompts you for the next command. When you have finished entering numbers, choose “Store.”

The system confirms the name, location and number, then announces that the entry has been stored. The system then ends the VR session. “Delete” *C Use the Delete command to erase one entry from the phone book, all entries from the phone book, the current redial number or the current call back number.

To delete entries from the phone book, say a name or “All entries” when prompted by the system.

The system acknowledges the command and asks you to confirm the deletion.

To delete the current redial number or call back number, say “redial number” or “call back number” when prompted by the system.

If a redial number or a call back number exists, the system deletes them without asking for confirmation.

If there is no number for the entry you are trying to delete, the system says so and ends the VR session.

Heater, air conditioner, audio and phone systems 4-33

Model "S35-D" EDITED: 2007/ 7/ 3

Black plate (178,1)

“List Names” *D Use the List Names command to hear all the names and locations in the phone book.

“Record” *B The system announces “Recording” and a tone sounds signaling you to begin.

Setup

The system recites the phone book entries but does not include the actual phone numbers. When the playback of the list is complete the system returns to the main menu.

You can stop the playback of the list at any time by pushing the button on the steering wheel. The system ends the VR session.

Memo pad

Speak the information you wish to record clearly. When you are done, push the button on the steering wheel.

or

A tone sounds and the system announces “Memo recorded.” Another tone sounds to end the VR session.

If the memo pad is full, the system asks if you wish to record over the oldest memo. “Delete” *C The Delete command erases all memos. The system asks you to confirm this action before deleting all memos.

The Memo Pad records a maximum of 6 voice memos, each up to 20 seconds long. “Play” *A The system plays back all the memos in the order of newest to oldest. The system ends the VR session.

If there are no memos recorded, the system announces “No messages to play.” The system ends the VR session. 4-34 Heater, air conditioner, audio and phone systems

Use the Setup command to change options associated with the Bluetooth® Hands-Free Phone System. “Pair Phone” *A Use the Pair Phone command to pair a phone to the Bluetooth® Hands-Free Phone System.

When you are asked to enter a PIN code for pairing your Bluetooth® cellular phone, operate it to enter the code “1234”. The code is always “1234” regardless of the number of phones paired.

NOTE: The pairing procedure must be performed when the vehicle is stationary. the vehicle starts moving during the proce-

If

Model "S35-D" EDITED: 2007/ 7/ 3

dure, the procedure will be cancelled. Also, see “Pairing procedure” earlier in this section for additional information.

Up to 5 phones can be paired. If you try to pair a the system announces that you sixth phone, must replace an existing phone.

first delete one phone or

If you try to pair a phone that has already been paired to your vehicle’s system, the system announces the name the phone is already using. The pairing procedure will then be canceled.

When prompted by the system, choose from the following commands:

“New phone” — see “Pairing procedure” earlier in this section.

“Replace phone” — The system announces the names of the phones already paired and asks which you would like to replace.

Once you say the name of the phone you wish to replace, the paring procedure will begin. (See “Pairing procedure” earlier in this section.)

“List phone” — See the description below.

“List Phones” *B the Use the List Phones command to hear names of If no phones are paired, the system announces, “No

the phones currently paired.

paired phones to list.” The system then ends the VR session. “Select Phone” *C Use the Select Phone command to select a phone of lesser priority when two or more phones paired with Bluetooth® Hands-Free Phone System are in the vehicle at the same time.

The system asks you to name the phone and confirm the selection.

Once the selection is confirmed, the selected phone remains active until the ignition switch is turned OFF or you select a new phone. “Change Priority” *D Use the Change Priority command to change the priority level of the active phone.

The priority level determines which phone is active when more than one paired Bluetooth® phone is in the vehicle.

The system states the priority level of the active phone and asks for a new priority level (1, 2, 3, 4, 5).

If the new priority level is already being used for another phone, the two phones will swap priority levels.

Black plate (179,1)

For example, if the current priority levels are:

Priority Level 1 = Phone A Priority Level 2 = Phone B Priority Level 3 = Phone C

and you change the priority level of Phone C to Level 1, then:

Priority Level 1 = Phone C Priority Level 2 = Phone B Priority Level 3 = Phone A

“Delete Phone” *E Use the Delete Phone command to delete a specific phone or all phones from the Bluetooth® Hands-Free Phone System.

The system announces the names of the phones already paired with the system and their priority level. The system then gives you the option to delete a specific phone, all phones or listen to the list again.

Once you chose to delete a phone or all phones, the system asks you to confirm this action.

NOTE: When you delete a phone, the associated phone book for that phone will also be deleted. “Select Ringtone” *F Use the Select Ringtone command to select the Heater, air conditioner, audio and phone systems 4-35

Model "S35-D" EDITED: 2007/ 7/ 3

Black plate (180,1)

of their own voice that is stored in the system. The system is capable of storing a different speaker adaptation model for memory A and memory B.

automatically. If both memory locations are already in use, the system will prompt you to overwrite one. Follow the instructions pro- vided by the system.

tone heard in the vehicle when an incoming call is received.

The system announces the name of the active phone and asks you to choose from the following commands:

“Ringtone” — The system plays a ringtone and asks if you would like to select that tone. If you say no, the system plays the next ringtone available and continues to cycle through the ringtones until you select one or quit.

“Silent” — The system asks you to confirm your wish to disable the ringtone.

“Bluetooth off” *G Use the Bluetooth® Off command to turn off the Bluetooth Hands-Free Phone System. When Bluetooth® Hands-Free Phone System is off, you will not be able to make or receive calls using NISSAN Voice Recognition. Also, you will not have access to the Phone Book.

You can still use the Memo Pad and access Setup.

SPEAKER ADAPTATION (SA) MODE Speaker Adaptation allows up to two out-of dialect users to train the system to improve recognition accuracy. By repeating a number of commands, the users can create a voice model 4-36 Heater, air conditioner, audio and phone systems

If memory A is available, the system will use memory A to store the model. If memory A is in use and memory B is available, the system will use memory B to store the model. If both of the memory locations are in use, the system will ask the user to select which memory location should be overwritten.

Training procedure The procedure for training a voice is as follows.

1. Position the vehicle in a reasonably quiet

outdoor location.

2. Sit

in the driver’s seat with the engine running, the parking brake applied, and the transmission in P (Park) position.

3. Push and hold the

button for more than

5 seconds.

4. The system announces: “Press the PHONE SEND ( the hands-free phone system to enter the speaker adapta- tion mode or press the PHONE END ( button to select a different language”.

) button for

5. Push the

button.

6. Voice memory A or memory B is selected

7. When preparation is complete and you are

ready to begin, push the

button.

8. The SA mode will be explained. Follow the

instructions provided by the system.

9. When training is finished, the system will tell you an adequate number of phrases have been recorded.

10. The system will ask you to say your name. Follow the instructions to register your name.

11. The system will announce that speaker adaptation has been completed and the system is ready.

The SA mode will stop if:

The seconds in SA mode.

button is pushed for more than 5

The vehicle is driven during SA mode.

The ignition switch is turned to the OFF or LOCK position.

Training phrases During the SA mode, the system instructs you to say the following phrases. (The system will

Model "S35-D" EDITED: 2007/ 7/ 3

Black plate (181,1)

prompt you for each phrase.)

phone book new entry

dial three oh four two nine

delete call back number

. Cancel

call back number

call star two zero nine five

delete phone

dial six six four three seven

setup pair phone

. memo pad play

eight pause nine three two pause seven

. Home

dial eight three zero five one

four three pause two nine pause zero

delete all entries

call seven two four zero nine

delete redial number

phone book list names

phone book delete entry

call eight oh five four one

dial star two one seven oh

. memo pad record . Yes . No

select ringtone

dial eight five six nine two

. Bluetooth on

setup change priority

. Correction

setup change ringtone

dial seven four oh one eight

setup main menu

. Delete . memo pad delete

dial nine seven two six six

call seven six three oh one

call three one nine oh two

nine seven pause pause three oh eight

go back

call five six two eight zero

Heater, air conditioner, audio and phone systems 4-37

Model "S35-D" EDITED: 2007/ 7/ 3

Black plate (182,1)

TROUBLESHOOTING GUIDE The system should respond correctly to all voice commands without difficulty. If problems are encountered, try the following solutions. Where the solutions are listed by number, try each solution in turn, starting with number 1, until the problem is resolved.

Symptom

Solution

1. Ensure that the command format is valid. (See “List of voice commands” earlier in this section.)

2. Ensure that the command is spoken after the tone.

3. Speak clearly without pausing between words and at a level appropriate to the ambient noise level in the vehicle.

System fails to interpret the command correctly.

4. Ensure that the ambient noise level is not excessive (for example, windows open or defroster on). NOTE: If it is too noisy to use the phone, it is likely that the voice commands will not be recognized.

The system consistently selects the wrong entry from the phone book.

5. If more than one command was said at a time, try saying the commands separately.

6. If the system consistently fails to recognize commands, the voice training procedure should be carried out to improve the recognition response for the speaker. (See “SPEAKER ADAPTATION (SA) MODE” earlier in this section.)

1. Ensure that the phone book entry name requested matches what was originally stored. This can be confirmed by using the “List Names” command. (See “Phone book” earlier in this section.)

2. Replace one of the names being confused with a new name.

4-38 Heater, air conditioner, audio and phone systems

Model "S35-D" EDITED: 2007/ 7/ 3

Black plate (16,1)

5 Starting and driving

Precautions when starting and driving . . . . . . . . . . . . . . . . . . . . . 5-2
Exhaust gas (carbon monoxide) . . . . . . . . . . . . . . . . . . . . . . . . . 5-2
Three-way catalyst. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2
Tire Pressure Monitoring System (TPMS). . . . . . . . . . . . . 5-3
Avoiding collision and rollover . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-5
On-pavement and off-road driving precautions . . . . . . 5-5
Drinking alcohol/drugs and driving. . . . . . . . . . . . . . . . . . . . . . 5-6
Driving safety precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6
Ignition switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-8
Intelligent Key system (if so equipped) . . . . . . . . . . . . . . . . 5-8
Continuously Variable Transmission (CVT) . . . . . . . . . . 5-10
Steering lock. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-10
Key positions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-10
Before starting the engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-11
Starting the engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-11
Driving the vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-12
Continuously Variable Transmission (CVT) . . . . . . . . . . 5-12
Parking brake . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-17
Cruise control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-18
Precautions on cruise control . . . . . . . . . . . . . . . . . . . . . . . . . . 5-18
Cruise control operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-19

Break-in schedule . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-20
Increasing fuel economy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-20
All-Wheel Drive (AWD) (if so equipped) . . . . . . . . . . . . . . . . 5-21
All-Wheel Drive (AWD) lock switch operations. . . . 5-21
AWD warning light . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-23
Parking/parking on hills. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-24
Electric power steering system . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-25
Brake system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-25
Braking precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-25
Parking brake break-in. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-26
Anti-lock Braking System (ABS) . . . . . . . . . . . . . . . . . . . . . . 5-26
Vehicle Dynamic Control (VDC) system . . . . . . . . . . . . . . . . . 5-27
Cold weather driving. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-29
Freeing a frozen door lock. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-29
Anti-freeze. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-29
Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-29
Draining of coolant water . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-29
Tire equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-29
Special winter equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-29
Driving on SNOW or ice. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-29
Engine block heater (if so equipped). . . . . . . . . . . . . . . . . 5-30

Model "S35-D" EDITED: 2007/ 7/ 3

Black plate (186,1)

PRECAUTIONS WHEN STARTING AND DRIVING

WARNING

. Do not leave children or adults who would normally require the support of others alone in your vehicle. Pets should not be left alone either. They could accidentally injure themselves or others through inadvertent op- eration of the vehicle. Also, on hot, sunny days, temperatures in a closed vehicle could quickly become high enough to cause severe or possibly fatal injuries to people or animals.

. Properly secure all cargo with ropes or straps to help prevent it from sliding or shifting. Do not place cargo higher than the seatbacks. In a sudden stop or collision, unse- cured cargo could cause personal injury.

EXHAUST GAS (carbon monoxide)

WARNING

. Do not breathe exhaust gases; they contain colorless and odorless car- bon monoxide. Carbon monoxide is

5-2 Starting and driving

dangerous. sciousness or death.

It can cause uncon-

If you suspect that exhaust fumes are entering the vehicle, drive with all windows fully open, and have the vehicle inspected immediately.

. Do not run the engine in closed

spaces such as a garage.

. Do not park the vehicle with the engine running for any extended length of time.

. Keep the lift gate closed while driving, otherwise exhaust gases could be drawn into the passenger compartment. If you must drive with the lift gate open, follow these precautions:

1. Open all the windows.

2. Set the

air recirculation to off and the fan control to high to circulate the air.

If electrical wiring or other cable connections must pass to a trailer through the seal on the lift gate or the body, follow the manufacturer’s recommendation to prevent carbon monoxide entry into the vehicle.

If a special body, camper or other equipment is added for recreational or other usage, follow the manufac- turer’s recommendation to prevent carbon monoxide entry into the vehicle. (Some recreational vehicle appliances such as stoves, refrig- erators, heaters, etc. may also gen- erate carbon monoxide.)

The exhaust system and body should be inspected by a qualified mechanic whenever:

— The vehicle is raised for service. — You suspect that exhaust fumes are entering into the passenger compartment.

— You notice a change in the

sound of the exhaust system.

— You have had an accident invol- ving damage to the exhaust system, underbody, or rear of the vehicle.

THREE-WAY CATALYST The three-way catalyst is an emission control device installed in the exhaust system. Exhaust gases in the three-way catalyst are burned at high temperatures to help reduce pollutants.

Model "S35-D" EDITED: 2007/ 7/ 3

WARNING

The exhaust gas and the exhaust system are very hot. Keep people, animals or flammable materials away from the exhaust system com- ponents.

. Do not stop or park the vehicle over flammable materials such as dry grass, waste paper or rags. They may ignite and cause a fire.

CAUTION

. Do not use leaded gasoline. Depos- its from leaded gasoline will ser- i o u s l y r e d u c e t h e t h r e e - w a y catalyst’s ability to help reduce ex- haust pollutants.

. Keep your engine tuned up. Mal- functions in the ignition, fuel injec- tion, or electrical systems can cause overrich fuel flow into the three-way catalyst, causing it to overheat. Do not keep driving if the engine mis- fires, or if noticeable loss of perfor- mance or other unusual operating conditions are detected. Have the

vehicle inspected promptly by a NISSAN dealer.

. Avoid driving with an extremely low fuel level. Running out of fuel could cause the engine to misfire, dama- ging the three-way catalyst.

. Do not race the engine while warm-

ing it up.

. Do not push or tow your vehicle to

start the engine.

TIRE PRESSURE MONITORING SYS- TEM (TPMS) Each tire, including the spare (if provided), should be checked monthly when cold and inflated to the inflation pressure recommended by the vehicle manufacturer on the vehicle placard or tire inflation pressure label. (If your vehicle has tires of a different size than the size indicated on the vehicle placard or tire inflation pressure label, you should determine the proper tire inflation pressure for those tires.)

As an added safety feature, your vehicle has been equipped with a Tire Pressure Monitoring System (TPMS) illuminates a low tire pressure telltale when one or more of your tires is significantly under-inflated. Accordingly, when the low tire pressure telltale illuminates, you should stop and check your tires as soon as

that

Black plate (187,1)

possible, and inflate them to the proper pres- sure. Driving on a significantly under-inflated tire causes the tire to overheat and can lead to tire failure. Under-inflation also reduces fuel effi- ciency and tire tread life, and may affect the vehicle’s handling and stopping ability.

Please note that the TPMS is not a substitute for proper tire maintenance, and it is the driver’s responsibility to maintain correct tire pressure, even if under-inflation has not reached the level to trigger the TPMS low tire pressure telltale.

illumination of

Your vehicle has also been equipped with a TPMS malfunction indicator to indicate when the system is not operating properly. The TPMS malfunction indicator is combined with the low tire pressure telltale. When the system detects a malfunction, the telltale will flash for approxi- mately one minute and then remain continuously illuminated. This sequence will continue upon subsequent vehicle start-ups as long as the malfunction exists. When the malfunction indi- cator is illuminated, the system may not be able to detect or signal low tire pressure as intended. TPMS malfunctions may occur for a variety of reasons, including the installation of replace- ment or alternate tires or wheels on the vehicle that prevent the TPMS from functioning properly. Always check the TPMS malfunction telltale after replacing one or more tires or wheels on your vehicle to ensure that the replacement or

Starting and driving 5-3

Model "S35-D" EDITED: 2007/ 7/ 3

Black plate (188,1)

alternate tires and wheels allow the TPMS to continue to function properly.

Additional information

The TPMS does not monitor pressure of the spare tire.

the tire

The TPMS will activate only when the vehicle is driven at speeds above 16 MPH (25 km/h). Also, this system may not detect a sudden drop in tire pressure (for example a flat tire while driving).

The low tire pressure warning light does not automatically turn off when the tire pressure is adjusted. After the tire is inflated to the recommended pressure, the vehicle must be driven at speeds above 16 MPH (25 km/h) to activate the TPMS and turn off the low tire pressure warning light. Use a tire pressure gauge to check the tire pressure.

Tire pressure rises and falls depending on the heat caused by the vehicle’s operation and the outside temperature. Low outside temperature can lower the temperature of the air inside the tire which can cause a lower tire inflation pressure. This may cause the low tire pressure warning light to illuminate. If the warning light illuminates in low ambient temperature, check the tire pressure for all four tires.

For additional

information, see “Low tire pres-

5-4 Starting and driving

sure warning light” in the “2. Instruments and controls” section and “TIRE PRESSURE MON- ITORING SYSTEM (TPMS)” in the “6. In case of emergency” section.

WARNING

If the low tire pressure warning light illuminates while driving, avoid sud- den steering maneuvers or abrupt braking, reduce vehicle speed, pull off the road to a safe location and stop the vehicle as soon as possi- ble. Driving with under-inflated tires may permanently damage the tires and increase the likelihood of tire failure. Serious vehicle damage could occur and may lead to an accident and could result in serious personal injury. Check the tire pres- sure for all four tires. Adjust the tire pressure to the recommended COLD tire pressure shown on the Tire and Loading Information label to turn the low tire pressure warning light OFF. If you have a flat tire, replace it with a spare tire as soon as possi- ble. (See “FLAT TIRE” in the “6. In case of emergency” section for changing a flat tire.)

. When a spare tire is mounted or a wheel is replaced, the TPMS will not function and the low tire pressure warning light will flash for approxi- mately 1 minute. The light will remain on after 1 minute. Contact your NISSAN dealer as soon as possible for tire replacement and/ or system resetting.

. Replacing tires with those not ori- ginally specified by NISSAN could affect the proper operation of the TPMS. . Do not

inject any tire liquid or aerosol tire sealant into the tires, as this may cause a malfunction of the tire pressure sensors.

CAUTION

The TPMS may not function properly when the wheels are equipped with tire chains or the wheels are buried in snow.

. Do not place metalized film or any metal parts (antenna, etc.) on the windows. This may cause poor re- ception of the signals from the tire

Model "S35-D" EDITED: 2007/ 7/ 3

pressure sensors, and the TPMS will not function properly.

AVOIDING COLLISION AND ROLL- OVER

Some devices and transmitters may temporarily interfere with the operation of the TPMS and cause the low tire pressure warning light to illuminate. Some examples are:

Facilities or electric devices using similar radio frequencies are near the vehicle.

If a transmitter set to similar frequencies is being used in or near the vehicle.

If a computer (or similar equipment) or a DC/ AC converter is being used in or near the vehicle.

FCC Notice:

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

This device complies with Part 15 of the FCC Rules and RSS-210 of Industry Cana- da.

Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause un- desired operation of the device.

WARNING

Failure to operate this vehicle in a safe and prudent manner may result in loss of control or an accident.

Be alert and drive defensively at all times. Obey all traffic regulations. Avoid excessive speed, high speed cornering, or sudden steering maneuvers, because these driving practices could cause you to lose control of your vehicle. As with any vehicle, a loss of control could result in a collision with other vehicles or objects, or cause the vehicle to rollover, particularly if the loss of control causes the vehicle to slide sideways. Be attentive at all times, and avoid driving when tired. Never drive when under the influence of alcohol or drugs (including prescription or over-the-counter drugs which may cause drowsiness). Always wear your seat belt as outlined in the “SEAT BELTS” in the “1. Safety — Seats, seat belts and supplemental restraint system” section of this manual, and also instruct your passengers to do so.

Seat belts help reduce the risk of injury in collisions and rollovers. In a rollover crash, an unbelted or improperly belted person is

Black plate (189,1)

significantly more likely to be injured or killed than a person properly wearing a seat belt.

ON-PAVEMENT AND OFF-ROAD DRIVING PRECAUTIONS Utility vehicles have a significantly higher rollover rate than other types of vehicles.

They have higher ground clearance than pas- senger cars to make them capable of performing in a variety of on-pavement and off-road applications. This gives them a higher center of gravity than ordinary cars. An advantage of higher ground clearance is a better view of the road, allowing you to anticipate problems. However, they are not designed for cornering at the same speeds as conventional passenger cars any more than low-slung sports cars are designed to perform satisfactorily under off-road conditions. If at all possible, avoid sharp turns or abrupt maneuvers, particularly at high speeds. As with other vehicles of this type, failure to operate this vehicle correctly may result in loss of control or vehicle rollover. Seat belts help reduce the risk of injury in collisions and rollovers. In a rollover crash, an unbelted or improperly belted person is significantly more likely to be injured or killed than a person properly wearing a seat belt.

Be sure to read “DRIVING SAFETY PRECAU- TIONS” later in this section.

Starting and driving 5-5

Model "S35-D" EDITED: 2007/ 7/ 3

DRINKING ALCOHOL/DRUGS AND DRIVING

WARNING

Never drive under the influence of alcohol or drugs. Alcohol in the blood- stream reduces coordination, delays reaction time and impairs judgement. Driving after drinking alcohol increases the likelihood of being involved in an accident injuring yourself and others. Additionally, if you are injured in an accident, alcohol can increase the se- verity of the injury.

NISSAN is committed to safe driving. However, you must choose not to drive under the influence of alcohol. Every year thousands of people are injured or killed in alcohol-related accidents. Although the local is considered to be legally intoxicated, the fact is that alcohol affects all people differently and most people underestimate the effects of alcohol.

laws vary on what

is true for drugs,

Remember, drinking and driving don’t mix! And that too (over-the-counter, prescription, and illegal drugs). Don’t drive if your ability to operate your vehicle is impaired by alcohol, drugs, or some other physical condition.

5-6 Starting and driving

DRIVING SAFETY PRECAUTIONS Your NISSAN is designed for both normal and off-road use. However, avoid driving in deep water or mud as your NISSAN is mainly designed for leisure use, unlike a conventional off-road vehicle.

Remember that Two-Wheel Drive (2WD) mod- els are less capable than All-Wheel Drive (AWD) models for rough road driving and extrication when stuck in deep snow, mud, or the like.

Please observe the following precautions:

WARNING

. Drive carefully when off the road and avoid dangerous areas. Every person who drives or rides in this vehicle should be seated with their seat belt fastened. This will keep you and your passengers in position when driving over rough terrain.

. Do not drive across steep slopes. Instead drive either straight up or straight down the slopes. Off-road vehicles can tip over sideways much more easily than they can forward or backward.

. Many hills are too steep for any

Black plate (190,1)

vehicle. If you drive up them, you may stall. If you drive down them, you may not be able to control your speed. If you drive across them, you may roll over.

. Do not shift ranges while driving on downhill grades as this could cause loss of control of the vehicle.

. Stay alert when driving to the top of a hill. At the top there could be a drop-off or other hazard that could cause an accident.

If your engine stalls or you cannot make it to the top of a steep hill, never attempt to turn around. Your vehicle could tip or roll over. Always back straight down in R (Reverse) range. Never back down in N (Neu- tral), using only the brake, as this could cause loss of control.

. Heavy braking going down a hill could cause your brakes to overheat and fade, resulting in loss of control and an accident. Apply brakes lightly and use a low range to control your speed.

. Unsecured cargo can be thrown around when driving over rough

Model "S35-D" EDITED: 2007/ 7/ 3

.

terrain. Properly secure all cargo so it will not be thrown forward and cause injury to you or your passen- gers.

To avoid raising the center of gravity excessively, do not exceed the rated capacity of the roof rack (if so equipped) and evenly distribute the load. Secure heavy loads in the cargo area as far forward and as low as possible. Do not equip the vehicle with tires larger than speci- fied in this manual. This could cause your vehicle to roll over.

. Do not grip the inside or spokes of the steering wheel when driving off- road. The steering wheel could move suddenly and injure your hands. Instead drive with your fin- gers and thumbs on the outside of the rim.

. Before operating the vehicle, ensure that the driver and all passengers have their seat belts fastened.

. Always drive with the floor mats in place as the floor may became hot.

Lower your speed when encounter- ing strong crosswinds. With a higher

center of gravity, your NISSAN is more affected by strong side winds. Slower speeds ensure better vehicle control.

. Do not drive beyond the perfor- mance capability of the tires, even with AWD engaged.

. For AWD equipped vehicles, do not attempt to raise two wheels off the ground and shift the transmission to any drive or reverse position with the engine running. Doing so may result in drivetrain damage or un- expected vehicle movement which could result in serious vehicle da- mage or personal injury.

. Do not attempt to test an AWD equipped vehicle on a 2-wheel dy- namometer (such as the dynam- ometers used by some states for emissions testing), or similar equip- ment even if the other two wheels are raised off the ground. Make sure you inform test facility personnel that your vehicle is equipped with AWD before it is placed on a dynamometer. Using the wrong test equipment may result in drivetrain damage or unexpected vehicle

Black plate (191,1)

movement which could result in serious vehicle damage or personal injury.

. When a wheel is off the ground due to an unlevel surface, do not spin the wheel excessively. (AWD mod- els)

. Accelerating quickly, sharp steering maneuvers or sudden braking may cause loss of control.

If at all possible, avoid sharp turning maneuvers, particularly at high speeds. Your vehicle has a higher center of gravity than a conventional passenger car. The vehicle is not designed for cornering at the same speeds as conventional passenger cars. Failure to operate this vehicle correctly could result in loss of control and/or a rollover accident.

. Always use tires of the same type, size, brand, construction (bias, bias- belted or radial), and tread pattern on all four wheels. Install traction devices on the front wheels when driving on slippery roads and drive carefully.

. Be sure to check the brakes imme-

Starting and driving 5-7

Model "S35-D" EDITED: 2007/ 7/ 3

diately after driving in mud or water. See “BRAKE SYSTEM” later in this section for wet brakes.

. Avoid parking your vehicle on steep hills. If you get out of the vehicle and it rolls forward, backward or sideways, you could be injured.

. Whenever you drive off-road through sand, mud or water as deep as the wheel hub, more frequent maintenance may be required. See the maintenance information in the “NISSAN Service and Maintenance Guide”.

. Spinning the front wheels on slip- pery surfaces may cause the AWD warning light to flash and the AWD system to automatically switch from the AWD mode to the 2WD mode. This could reduce traction. Be espe- cially careful when towing a trailer. (AWD models)

5-8 Starting and driving

IGNITION SWITCH

SSD0669

INTELLIGENT KEY SYSTEM (if so equipped) The Intelligent Key system can operate the ignition switch without taking the key out from your pocket or purse. The operating environment and/or conditions may affect the Intelligent Key system operation.

CAUTION

. Be sure to carry the Intelligent Key with you when operating the vehi- cle.

. Never leave the Intelligent Key in- side the vehicle when you leave the

Black plate (192,1)

vehicle.

If the vehicle battery is discharged, the ignition switch cannot be moved from the LOCK position and if the steering lock is engaged, the steer- ing wheel cannot be moved. Charge the battery as soon as possible. See “JUMP STARTING” in the “6. In case of emergency” section.

Model "S35-D" EDITED: 2007/ 7/ 3

.

operating range, but the Intelligent Key may function.

the Intelligent Key is placed on the inside the glove box or the Intelligent Key may not

If instrument panel, door pocket, function.

If the Intelligent Key is placed near the door or window outside the vehicle, the Intelligent Key may function.

SSD0436

Operating range The Intelligent Key functions can only be used for starting the engine when the Intelligent Key is within the specified operating range *1 . When the Intelligent Key battery is almost discharged or strong radio waves are present near the operating location, the Intelligent Key system’s operating range becomes narrower and may not function properly.

If the Intelligent Key is within the operating range, it is possible for anyone, even someone who does not carry the Intelligent Key, to turn the ignition switch to start the engine.

The cargo area is not

included in the

Black plate (193,1)

Without Intelligent Key system

SSD0392

With Intelligent Key system

SSD0437A

Starting and driving 5-9

Model "S35-D" EDITED: 2007/ 7/ 3

CONTINUOUSLY VARIABLE TRANS- MISSION (CVT) The ignition lock is designed so that the ignition switch cannot be turned to the LOCK position until the selector lever is moved to the P (Park) position. . When turning the ignition switch to the LOCK position, make sure that the selector lever is in the P (Park) position.

. When removing the key from the ignition switch (if it is inserted), make sure that the selector lever is in the P (Park) position.