2007 Nissan Pathfinder Owners Manual

When the or positions in between are selected, the air conditioner automatically turns on (however, the indicator light will not illuminate) if the outside temperature is more than 36(cid:176)F (2(cid:176)C). The air conditioning system will con- tinue to operate until the fan control dial is turned to OFF or the vehicle is shut off, even if the air flow is turned to a position other than control dial position. This dehumidifies the air the which helps defog the windshield. The mode automatically turns off, allowing outside air to be drawn into the passenger compartment to further improve the defogging performance.

4-18 Display screen, heater, air conditioner and audio systems

4. Turn the temperature control dial to the de-

sired position. Operating tips c Keep the windows and sunroof

(if so equipped) closed while the air conditioner is in operation.

c After parking in the sun, drive for 2 or 3
minutes with the windows open to vent hot air from the passenger compartment. Then, close the windows. This allows the air con- ditioner to cool the interior more quickly.

c The air conditioning system should be operated for approximately 10 minutes at least once a month. This helps pre- vent damage to the system due to lack of lubrication.

c A visible mist may be seen coming from the ventilators in hot, humid conditions as the air is cooled rapidly. This does not indicate a malfunction.

c If

the engine coolant

temperature gauge indicates engine coolant tem- perature over the normal range, turn the air conditioner off. See (cid:147)If your vehicle overheats(cid:148) in the (cid:147)In case of emergency(cid:148) section of this manual.

Z REVIEW COPY—2007 Pathfinder (pat) Owners Manual—USA_English (nna) 10/16/06—cathy X

AIR FLOW CHARTS The following charts show the button and dial positions for MAXIMUM AND QUICK heating, cooling or defrosting. For additional information on heating and cooling see (cid:147)Heater and air con- ditioner(cid:148) in this section(cid:148). The air recirculation ) button should always be in the OFF position for heating and defrosting.

Display screen, heater, air conditioner and audio systems 4-19

WHA0780

Z REVIEW COPY—2007 Pathfinder (pat) Owners Manual—USA_English (nna) 10/16/06—cathy X

4-20 Display screen, heater, air conditioner and audio systems

WHA0781

WHA0782

Z REVIEW COPY—2007 Pathfinder (pat) Owners Manual—USA_English (nna) 10/16/06—cathy X

WHA0783

WHA0784

Display screen, heater, air conditioner and audio systems 4-21

Z REVIEW COPY—2007 Pathfinder (pat) Owners Manual—USA_English (nna) 10/16/06—cathy X

HEATER AND AIR CONDITIONER (automatic) (if so equipped)

Driver temperature control dial Front window defroster button Fan speed control and system OFF dial AUTO button Passenger temperature control dial A/C ON/OFF button Rear control and fan speed dial Rear window defroster button

1. 2. 3. 4. 5. 6. 7. 8. 9. MODE button 10. Air recirculation button 11. Rear temperature control dial

LHA0491

WARNING

c The air conditioner cooling function op- erates only when the engine is running. c Do not leave children or adults who would normally require the assistance of others alone in your vehicle. Pets should also not be left alone. They could accidentally injure themselves or others through inadvertent operation of the vehicle. Also, on hot, sunny days, temperatures in a closed vehicle could quickly become high enough to cause severe or possibly fatal injuries to people or animals.

4-22 Display screen, heater, air conditioner and audio systems

c Do not use the recirculation mode for long periods as it may cause the interior air to become stale and the windows to fog up.

Start the engine and operate the controls to activate the air conditioner. AUTOMATIC OPERATION Cooling or heating (auto) This mode may be normally used all year round as the system automatically works to keep a con- stant temperature. Air flow distribution and fan speed are also controlled automatically. 1. Push the AUTO button on. (AUTO will be

displayed.)

2. Turn the driver(cid:146)s side temperature control dial to the left or right to set the desired temperature. Driver and passenger tem- peratures can be set independently. Press AUTO a second time to activate dual climate control functions. Turn the passenger(cid:146)s side temperature control dial to the left or right to set the desired passenger(cid:146)s temperature.

c Adjust the temperature dial to about 75(cid:176)F

(24(cid:176)C) for normal operation.

Z REVIEW COPY—2007 Pathfinder (pat) Owners Manual—USA_English (nna) 10/16/06—cathy X

Air flow control Pushing the MODE button manually controls air flow and selects the air outlet:

(cid:151) Air flows from center and side

ventilators.

(cid:151) Air flows from center and side

ventilators and foot outlets.

(cid:151) Air flows mainly from foot outlets. (cid:151) Air flows from defroster and foot

outlets.

(cid:151) Air flows from defroster outlets.

To turn system off Turn and hold the fan speed control dial all the way to the left ( 0 ) until the system turns off.

c The temperature of the passenger compart- ment will be maintained automatically. Air flow distribution, fan speed and A/C on/off are also controlled automatically.

c A visible mist may be seen coming from the ventilators in hot, humid conditions as the air is cooled rapidly. This does not indicate a malfunction.

Dehumidified defrosting or defogging 1. Push the defroster control button

to turn the system on. The display will show the defrost icon.

2. Turn the temperature dial to the left or right

to set the desired temperature.

c To quickly remove ice from the outside of the windows, turn the manual fan control dial to the maximum position

c As soon as possible after the windshield is clean, push the AUTO button to return to the auto mode.

c When the DEF control

is activated, the air conditioner will automatically be turned on at outside temperatures above 36(cid:176)F (2(cid:176)C). If in defrost mode for more than one minute, the air conditioning system will continue to operate until the fan control is turned OFF or the vehicle is shut off, even if

the air flow MODE control button is used to posi- select a position other than the tion. This dehumidifies the air which helps defog the windshield. The air recirculation mode automatically turns off, allowing out- side air to be drawn into the passenger compartment to further improve the defog- ging performance.

MANUAL OPERATION Fan speed control dial Turn the fan speed control dial left or right to manually control the fan speed or turn the system on or off.

Push the AUTO button to return to automatic control of the fan speed. Air recirculation The mode automatically turns off, allowing outside air to be drawn into the passenger com- partment to prevent fogging.

Push the air recirculation button to recir- culate interior air inside the vehicle. Push the AUTO button to return to automatic mode.

The air recirculation button will not be activated when the air conditioner is in DEF, floor, or floor/defrost mode.

Display screen, heater, air conditioner and audio systems 4-23

Z REVIEW COPY—2007 Pathfinder (pat) Owners Manual—USA_English (nna) 10/16/06—cathy X

OPERATING TIPS c When the engine coolant temperature and outside air temperature are low, the air flow from the foot outlets may not operate for a maximum of 150 seconds. However, this is not a malfunction. After the coolant tempera- ture warms up, air flow from the foot outlets will operate normally.

LIC0835
The sunload sensor s1 , located on the top center of the instrument panel, helps the system main- tain a constant temperature. Do not put anything on or around this sensor.

WHA0509

1. Rear fan speed control dial. 2. Rear temperature control dial. REAR CONTROL DIAL You can adjust the climate control system for rear seat passengers using the dials on the main control panel. Front passengers can control the rear functions by placing the controls on any setting other than the (cid:147)R(cid:148).

4-24 Display screen, heater, air conditioner and audio systems

Z REVIEW COPY—2007 Pathfinder (pat) Owners Manual—USA_English (nna) 10/16/06—cathy X

REAR SEAT AIR CONDITIONER

SERVICING AIR CONDITIONER

To operate the rear air conditioner, the engine must be running. The rear seat air conditioner can be turned on and off from the front controls. If the rear seat fan control dial is set to (0), the air conditioner is turned off. If it is set to any of the fan speed positions, air is discharged from the rear vents at the corresponding speed. When the rear seat fan control dial is set to (R), the rear seat passengers control their own fan speed.

The air conditioner system in your NISSAN ve- hicle is charged with a refrigerant designed with the environment in mind. This refrigerant does not harm the earth(cid:146)s ozone layer. Special charging equipment and lubricant is re- quired when servicing your NISSAN air condi- tioner. Using improper refrigerants or lubricants will cause severe damage to your air conditioner system. See (cid:147)Air conditioner system refrigerant and lubricant recommendations(cid:148) in the (cid:147)Techni- cal and consumer information(cid:148) section of this manual. A NISSAN dealer is able to service your (cid:147)environ- mentally friendly(cid:148) air conditioning system.

WARNING

The air conditioner system contains re- frigerant under high pressure. To avoid personal injury, any air conditioner ser- vice should be done only by an experi- enced technician with proper equipment.

LHA0490

Rear fan speed control dial. Rear temperature control dial.

1. 2. CONTROLS Fan control dial The fan control dial turns the rear vent fan on and off, and controls fan speed. Temperature control dial The temperature control dial allows rear passen- gers to adjust the temperature of the outlet air.

Display screen, heater, air conditioner and audio systems 4-25

Z REVIEW COPY—2007 Pathfinder (pat) Owners Manual—USA_English (nna) 10/16/06—cathy X

AUDIO SYSTEM

RADIO Turn the ignition key to the ACC or ON position and press the PWR (power)/VOL (volume) knob to turn the radio on. If you listen to the radio with the engine not running, the key should be turned to the ACC position.

Radio reception is affected by station signal strength, distance from radio transmitter, build- ings, bridges, mountains and other external influ- ences. Intermittent changes in reception quality normally are caused by these external influences. Using a cellular phone in or near the ve- hicle may influence radio reception quality. Radio reception Your NISSAN radio system is equipped with state-of-the-art electronic circuits to enhance ra- dio reception. These circuits are designed to extend reception range, and to enhance the qual- ity of that reception.

However there are some general characteristics of both FM and AM radio signals that can affect radio reception quality in a moving vehicle, even when the finest equipment is used. These char- acteristics are completely normal in a given re- ception area, and do not indicate any malfunction in your NISSAN radio system.

Reception conditions will constantly change be- cause of vehicle movement. Buildings, terrain, signal distance and interference from other ve- hicles can work against ideal reception. De- scribed below are some of the factors that can affect your radio reception. FM RADIO RECEPTION Range: FM range is normally limited to 25 (cid:150) 30
miles (40 (cid:150) 48 km), with monaural (single chan- nel) FM having slightly more range than stereo FM. External influences may sometimes interfere with FM station reception even if the FM station is within 25 miles (40 km). The strength of the FM signal is directly related to the distance between the transmitter and receiver. FM signals follow a line-of-sight path, exhibiting many of the same characteristics as light. For example, they will reflect off objects.

Fade and drift: As your vehicle moves away from a station transmitter, the signals will tend to fade and/or drift.

Static and flutter: During signal interference from buildings, large hills or due to antenna position (usually in conjunction with increased distance from the station transmitter) static or flutter can be heard. This can be reduced by adjusting the treble control to reduce treble response.

4-26 Display screen, heater, air conditioner and audio systems

Multipath reception: Because of the reflective characteristics of FM signals, direct and reflected signals reach the receiver at the same time. The signals may cancel each other, resulting in mo- mentary flutter or loss of sound. AM RADIO RECEPTION AM signals, because of their low frequency, can bend around objects and skip along the ground. In addition, the signals can be bounced off the ionosphere and bent back to earth. Because of these characteristics, AM signals are also sub- ject to interference as they travel from transmitter to receiver.

Fading: Occurs while the vehicle is passing through freeway underpasses or in areas with many tall buildings. It can also occur for several seconds during ionospheric turbulence even in areas where no obstacles exist.

Static: Caused by thunderstorms, electrical power lines, electric signs and even traffic lights. SATELLITE RADIO RECEPTION (if so equipped) When the satellite radio is first installed or the battery has been replaced, the satellite radio may not work properly. This is not a malfunction. Wait more than 10 minutes with satellite radio ON and

Z REVIEW COPY—2007 Pathfinder (pat) Owners Manual—USA_English (nna) 10/16/06—cathy X

the vehicle outside of any metal or large building for satellite radio to receive all of the necessary data. No satellite radio reception is available and (cid:147)NO SAT(cid:148) is displayed when the SAT band option is selected unless optional satellite receiver and antenna are installed and an XMT or SIRIUS(cid:153) satellite radio service subscription is active. Sat- ellite radio can only be installed in vehicles that were factory pre-wired for satellite radio. Satellite radio is not available in Alaska, Hawaii and Guam. Satellite radio performance may be affected if cargo carried on the roof blocks the satellite radio signal. If possible, do not put cargo over the satellite antenna.

Compact disc (CD) player

CAUTION

c Do not force a compact disc into the CD insert slot. This could damage the CD and/or CD changer/player.

c Trying to load a CD with the CD door closed could damage the CD and/or CD changer.

c Only one CD can be loaded into the CD

player at a time.

c Only use high quality 4.7 inches (12 cm) round discs that have the (cid:147)COMPACT disc DIGITAL AUDIO(cid:148) logo on the disc or packaging.

c During cold weather or rainy days, the player may malfunction due to the hu- midity. If this occurs, remove the CD and dehumidify or ventilate the player completely.

c The player may skip while driving on

rough roads.

LHA0099
AUDIO OPERATION PRECAUTIONS

c The CD player sometimes cannot func- tion when the compartment tempera- ture low. Decrease/increase the temperature before use.

extremely high or

is

Display screen, heater, air conditioner and audio systems 4-27

Z REVIEW COPY—2007 Pathfinder (pat) Owners Manual—USA_English (nna) 10/16/06—cathy X

c Do not expose the CD to direct sun-

light.

c CDs that are in poor condition or are dirty, scratched or covered with finger- prints may not work properly.

c The following CDs may not work prop-

erly: c Copy control compact discs (CCCD) c Recordable compact discs (CD-R) c Rewritable compact discs (CD-RW) c Do not use the following CDs as they may cause the CD player to malfunc- tion: c 3.1 in (8 cm) discs with an adapter c CDs that are not round c CDs with a paper label c CDs that are warped, scratched, or

have abnormal edges

c This audio system can only play pre- recorded CDs. It has no capability to record or burn CDs.

c If the CD cannot be played, one of the following messages will be displayed.

CHECK DISC: c Confirm that the CD is inserted cor- rectly (the label side is facing up, etc.).

c Confirm that the CD is not bent or

warped and it is free of scratches.

PRESS EJECT:

This is an error due to excessive tem- perature inside the player. Remove the CD by pressing the EJECT button. After a short time, reinsert the CD. The CD can be played when the temperature of the player returns to normal. UNPLAYABLE: The file is unplayable in this audio sys- tem (only MP3 or WMA CD).

Compact Disc with MP3 or WMA Terms: c MP3 (cid:151) MP3 is short for Moving Pictures Experts Group Audio Layer 3. MP3 is the most well-known compressed digital audio file format. This format allows for near (cid:147)CD quality(cid:148) sound, but at a fraction of the size of normal audio files. MP3 conversion of an audio track from CD-ROM can reduce the file size by approximately a 10:1 ratio with

virtually no perceptible loss in quality. MP3
compression removes the redundant and irrelevant parts of a sound signal that the human ear doesn(cid:146)t hear.

c WMA (cid:151) Windows Media Audio (WMA)* is a compressed audio format created by Mi- crosoft as an alternative to MP3. The WMA codec offers greater file compression than the MP3 codec, enabling storage of more digital audio tracks in the same amount of space when compared to MP3s at the same level of quality.

c Bit rate (cid:151) Bit rate denotes the number of bits per second used by a digital music file. The size and quality of a compressed digital audio file is determined by the bit rate used when encoding the file.

c Sampling frequency (cid:151) Sampling frequency is the rate at which the samples of a signal are converted from analog to digital (A/D conversion) per second.

c Multisession (cid:151) Multisession is one of the methods for writing data to media. Writing data once to the media is called a single session, and writing more than once is called a multisession.

4-28 Display screen, heater, air conditioner and audio systems

Z REVIEW COPY—2007 Pathfinder (pat) Owners Manual—USA_English (nna) 10/16/06—cathy X

c ID3/WMA Tag (cid:151) The ID3/WMA tag is the part of the encoded MP3 or WMA file that contains information about the digital music file such as song title, artist, encoding bit rate, track time duration, etc. ID3 tag infor- mation is displayed on the Artist/song title line on the display.

* WindowsT and Windows MediaT are regis- tered trademarks and trademarks in the United States of America and other countries of Mi- crosoft Corporation of the USA.

c If there is a file in the top level of the disc,

(cid:147)Root Folder(cid:148) is displayed.

c The playback order is the order in which the files were written by the writing software. Therefore, the files might not play in the desired order.

WHA0773

Playback order chart

Playback order: Music playback order of a CD with MP3 or WMA files is as illustrated. c The names of folders not containing MP3 or

WMA files are not shown in the display.

Display screen, heater, air conditioner and audio systems 4-29

Z REVIEW COPY—2007 Pathfinder (pat) Owners Manual—USA_English (nna) 10/16/06—cathy X

Specification chart:

Supported media Supported file systems

Supported versions*1

MP3

WMA

Version Sampling frequency Bit rate Version Sampling frequency Bit rate

Tag information Folder levels Text character number limitation

Displayable character codes*2

CD, CD-R, CD-RW ISO9660 LEVEL1, ISO9660 LEVEL2, Apple ISO, Romeo, Joliet * ISO9660 Level 3 (packet writing) is not supported. MPEG1, MPEG2, MPEG2.5
8 kHz - 48 kHz 8 kbps - 320 kbps, VBR WMA7, WMA8, WMA9
32 kHz - 48 kHz 48 kbps - 192 kbps, VBR ID3 tag VER1.0, VER1.1, VER2.2, VER2.3 (MP3 only) Folder levels: 8, Max folders: 255 (including root folder), Files: 512 (Max. 255 files for one folder) 128 characters 01: ASCII, 02: ISO-8859-1, 03: UNICODE (UTF-16 BOM Big Endian), 04: UNICODE (UTF-16 Non-BOM Big Endian), 05: UNICODE (UTF-8), 06: UNICODE (Non-UTF-16 BOM Little Endian)

*1 Files created with a combination of 48 kHz sampling frequency and 64 kbps bit rate cannot be played.

*2 Available codes depend on what kind of media, versions and information are going to be displayed.

4-30 Display screen, heater, air conditioner and audio systems

Z REVIEW COPY—2007 Pathfinder (pat) Owners Manual—USA_English (nna) 10/16/06—cathy X

Troubleshooting guide:

Symptom

Cannot play

Poor sound quality

It takes a relatively long time before the music starts playing.

Music cuts off or skips

Skipping with high bit rate files Moves immediately to the next song when playing Songs do not play back in the desired order

Cause and Countermeasure

Check if the disc was inserted correctly. Check if the disc is scratched or dirty. Check if there is condensation inside the player. If there is, wait until the condensation is gone (about 1 hour) before using the player. If there is a temperature increase error, the CD player will play correctly after it returns to the normal temperature. Files with extensions other than (cid:147).MP3(cid:148), (cid:147).mp3(cid:148) or (cid:147).wma(cid:148) cannot be played. In addition, the character codes and number of characters for folder names and file names should be in compliance with the specifications. Check if the finalization process, such as session close and disc close, is done for the disc. Check if the disc is protected by copyright. Check if the disc is scratched or dirty. Bit rate may be too low. If there are many folders or file levels on the MP3/WMA disc, or if it is a multisession disc, some time may be required before the music starts playing.

The writing software and hardware combination might not match, or the writing speed, writing depth, writing width, etc., might not match the specifications. Try using the slowest writing speed. Skipping may occur with large quantities of data, such as for high bit rate data.

When a non-MP3/WMA file has been given an extension of (cid:147).MP3(cid:148), (cid:147).WMA(cid:148), .(cid:147)mp3(cid:148)or (cid:147).wma(cid:148), or when play is prohibited by copyright protection, there will be approximately 5 seconds of no sound and then the player will skip to the next song. The playback order is the order in which the files were written by the writing software. Therefore, the files might not play in the desired order.

Display screen, heater, air conditioner and audio systems 4-31

Z REVIEW COPY—2007 Pathfinder (pat) Owners Manual—USA_English (nna) 10/16/06—cathy X

FM/AM RADIO WITH COMPACT DISC (CD) PLAYER (if so equipped) For all operation precautions, see 9Audio opera- tion precautions9 earlier in this section. Audio main operation PWR/VOL control knob

Turn the ignition key to the ACC or ON position, then press the PWR/VOL control knob. If you listen to the radio with the engine not running, turn the key to the ACC position. The mode (radio or CD) that was playing immediately before the system was turned off resumes playing. When no CD is loaded, the radio comes on. Pressing the PWR/VOL control knob again turns the system off. Turn the PWR/VOL control knob to the right to increase volume or to the left to decrease volume. AUDIO button (Bass, Treble, Fade, Bal- ance): Press the AUDIO button to change the mode as follows: BASS ! TREB ! FAD ! BAL ! Audio or OFF ! BASS To adjust Bass, Treble, Fade and Balance, press the AUDIO button until the desired mode ap-

WHA0586

PRESET A•B•C button Display screen

1. 2. 3. CD button 4. 5. CD insert slot 6. MENU button 4-32 Display screen, heater, air conditioner and audio systems

7. 8. 9. 10. PWR/VOL control knob 11. BAND button

AUDIO button Station select (1 - 6) buttons SEEK/TRACK (FF/REV) button

CD eject button

Z REVIEW COPY—2007 Pathfinder (pat) Owners Manual—USA_English (nna) 10/16/06—cathy X

pears in the display. Press the SEEK/TRACK button to adjust Bass and Treble to the desired level. You can also use the SEEK/TRACK button to adjust Fader and Balance modes. Fader ad- justs the sound level between the front and rear speakers and Balance adjusts the sound be- tween the right and left speakers.

Once you have adjusted the sound quality to the desired level, press the AUDIO button repeatedly until the radio or CD display reappears. Other- wise, the radio or CD display will automatically reappear after about 7 seconds. Clock set

1. Press and hold the MENU button until

it beeps (for more than 2 seconds) to enter the clock set mode.

2. The hours will start SEEK/TRACK button just the hours.

flashing. Press the to ad-

or

3. Press the MENU button until the radio beeps

to switch to the minute adjustment.

4. The minutes will start flashing. Press the to ad-

or

SEEK/TRACK button just the minutes.

5. Press the MENU button again to exit the

clock set mode.

The display will return to the regular clock display after 7 seconds, or press the MENU button again to return to the regular clock display. FM/AM radio operation FM/AM band select:

Pressing the BAND button will change the band as follows: AM ˆ! FM When the BAND button is pressed while the ignition switch is in the ACC or ON position, the radio will come on at the station last played.

If a compact disc is playing when the BAND button is pressed, the compact disc will auto- matically be turned off and the last radio station played will come on.

The FM stereo indicator, ST, illuminates during FM stereo reception. When the stereo broadcast signal is weak, the radio automatically changes from stereo to monaural reception. MENU button:

Press the MENU button while the radio is playing to change the tuning mode as follows: SEEK tuning mode ! TUNE mode ! SCAN tuning mode

TUNE and SCAN are shown in the display win- dow for each mode. No icon is displayed for SEEK tuning.

SEEK tuning

or

While in SEEK tuning mode, press the for less SEEK/TRACK button than 1.5 seconds. SEEK tuning begins from low to high frequencies or high to low frequencies, depending on which button is pressed, and stops at the next broadcasting station. Press the button, once the highest broadcasting station is reached, the radio continues in the SEEK mode the lowest broadcasting station. Press at the button, once the lowest broadcasting station is reached, the radio continues in the SEEK mode at the highest broadcasting station.

Manual tuning

While in TUNE mode, press the SEEK/TRACK for manual tuning. Press button and hold the SEEK/TRACK button or

to move quickly through the channels.

or

SCAN tuning

While in SCAN tuning mode, press and hold the SEEK/TRACK button for more than 1.5 seconds.

or

Display screen, heater, air conditioner and audio systems 4-33

Z REVIEW COPY—2007 Pathfinder (pat) Owners Manual—USA_English (nna) 10/16/06—cathy X

or

Scan tuning begins from low to high frequencies or high to low frequencies, depending on which SEEK/TRACK button is pressed. scan tuning stops at each broadcasting station for 5 seconds. When scanning, SCAN illumi- nates in the display and the radio station blinks. When temporarily stopped on a station, SCAN blinks and the radio station display is solid. Pressing or again during this 5 second period stops scan tuning and the radio remains tuned to that radio station. Station memory operations:

the SEEK/TRACK button

18 stations can be set for the FM and AM radio to the A, B and C preset button in any combination of AM or FM stations. 1. Press the PRESET A•B•C button to change between storage banks. The radio displays the icon A, B or C to indicate which set of presets are active.

2. Tune to the desired station using manual TUNE or SEEK tuning. Press and hold any of the desired station memory buttons (1 (cid:150) 6) until a beep sound is heard. (The radio mutes when the select button is pressed.)

3. The channel indicator will then come on and the sound will resume. Programming is now complete.

4. Other buttons can be set in the same man-

ner.

If the battery cable is disconnected, or if the fuse opens, the radio memory will be canceled. In that case, reset the desired stations. Compact disc (CD) player operation Turn the ignition key to the ACC or ON position, and carefully insert the compact disc into the slot with the label side up. The compact disc is auto- matically pulled into the slot and starts to play.

If the radio is already operating, it automatically turns off and the compact disc begins to play. CD button:

When the CD button is pressed with a compact disc loaded and the radio playing, the radio turns off and the compact disc starts to play.

SEEK/TRACK button:

the SEEK/TRACK button

is When pressed while the compact disc is playing, the next track following the present one starts to play from the beginning. Press SEEK/TRACK button several times to skip several tracks. Each time the button is pressed, the CD ad- vances 1 additional track. The track number ap-

pears in the display window. (When the last track on the compact disc is skipped, the first track is played.)

is pressed, When SEEK/TRACK button the track being played returns to the beginning. Press SEEK/TRACK button several times to skip back several tracks. Each time the button is pressed the CD moves back 1 track.

SEEK/TRACK (FF/REV) button:

Press and hold the SEEK/TRACK button or while a compact disc is playing, the compact disc plays at an increased speed while fast forwarding or rewinding. When the button is released, the compact disc returns to normal play speed. MENU button:

When the MENU button is pressed while the compact disc is playing, the play pattern changes as follows: RPT ˆ! MIX ˆ! Normal RPT: The track that is currently playing will be repeated.

MIX: The order of the tracks on the disc will be mixed during play, not following the sequence on the compact disc. The same track may be re-

4-34 Display screen, heater, air conditioner and audio systems

Z REVIEW COPY—2007 Pathfinder (pat) Owners Manual—USA_English (nna) 10/16/06—cathy X

button while in the peated twice. Press the MIX mode and tracks will be chosen at random. When a new compact disc is inserted, the play pattern automatically changes to normal.

CD EJECT:

button is pressed with a com- the compact disc will be

When the pact disc loaded, ejected. When the button is pressed while the compact disc is playing, the compact disc will eject and the system will turn off. CD IN indicator: This a CD is loaded with the audio system on.

indicator appears on the display when

1. 2. 3. 4.

PRESET A•B•C button Display screen DISP/CLOCK button SEEK/TRACK button

Type A

5. CD or CD/REAR AV (if so equipped)

WHA0734

button RADIO button* AUX button SCAN RPT button

6. 7. 8.

Display screen, heater, air conditioner and audio systems 4-35

Z REVIEW COPY—2007 Pathfinder (pat) Owners Manual—USA_English (nna) 10/16/06—cathy X

LOAD button

9. CAT FOLDER button 10. 11. CD insert slot 12. 13. PWR/VOL control knob 14. Station and CD select (1 (cid:150) 6) buttons 15. AUDIO/TUNE button

CD eject button

*No satellite radio reception is available when the RADIO button is pressed to access satellite radio stations unless optional satellite receiver and antenna are installed and an XMT or SIRIUS(cid:153) satellite radio service subscription is active. Satellite radio can only be in- stalled in vehicles that were factory pre- wired for satellite radio. Satellite radio is not available in Alaska, Hawaii and Guam.

tem is off to call up the mode (radio or CD) which was playing immediately before the system was turned off.

To turn the system off, press the PWR/VOL con- trol knob. Turn the PWR/VOL control knob to adjust the volume. This vehicle may be equipped with Speed Sen- sitive Volume (SSV) for audio. The audio volume changes as the driving speed changes. AUDIO knob (BASS, MIDRANGE, TREBLE, FADE, BALANCE and SSV if so equipped): Press the AUDIO knob to change the mode as follows: BASS ! MID ! TREBLE ! FADE ! BALANCE ! SSV (if so equipped) To adjust Bass, Mid (Midrange), Treble, Fade and Balance, press the AUDIO knob until the desired mode appears in the display. Turn the Tuning knob to adjust Bass and Treble to the desired level. You can also use the Tuning knob to adjust Fader and Balance modes. Fader adjusts the sound level between the front and rear speakers and Balance adjusts the sound between the right and left speakers. To change the SSV mode to OFF, LOW, MID or HIGH, turn the Tuning knob to the right or left.

Once you have adjusted the sound quality to the desired level, press the AUDIO knob repeatedly until the radio or CD display reappears. Other- wise, the radio or CD display will automatically reappear after about 10 seconds. Clock set

1. Press the DISP/CLOCK button until

it

beeps (>1.5 seconds).

2. The hours will start flashing. Press the CAT button or SEEK button to adjust the

or

or

FOLDER TRACK hours.

3. Press the DISP/CLOCK button again to

switch to the minute adjustment.

4. Press the CAT FOLDER button or SEEK TRACK button to adjust the minutes.

or or

5. Press the DISP/CLOCK button again to exit

the clock set mode.

The display will return to the regular clock display after 7 seconds, or you may press the DISP/CLOCK button again to return to the regu- lar clock display. DISP (display) button: This DISP (display) button will show text about MP3, SAT or CD information in the audio display.

FM/AM/SAT RADIO WITH COMPACT DISC (CD) CHANGER (if so equipped) Audio main operation POWER/VOLUME control: Turn the ignition key to ACC or ON, and then press the PWR/VOL control knob while the sys- 4-36 Display screen, heater, air conditioner and audio systems

Z REVIEW COPY—2007 Pathfinder (pat) Owners Manual—USA_English (nna) 10/16/06—cathy X

CD display mode

MP3 display mode

To change the text displayed while playing a CD with text, press the DISP button. The DISP button will allow you to scroll through CD text as follows: Disc title ˆ! Track title. To change the default display mode, press the AUDIO knob repeatedly until DISPLAY MODE appears on the display, then rotate the knob to select the following display modes: Disc number ˆ! Folder number. Once the display mode is selected, press the AUDIO knob again to store the setting. If the AUDIO knob is not pressed within 8 seconds, the display will refresh with the last selected display mode setting. c Track title mode displays the title of the se-

lected CD track.

c Disc title mode displays the title of the CD

being played.

c Track number mode displays the number selected disc and the track that is currently being played on the disk.

To change the text displayed when listening to an MP3/WMA CD with MP3/WMA text (when CD with text is being used), press the DISP button. The DISP button will scroll through the CD text as follows: Track title ˆ! Folder title ˆ! Artist title ˆ! Disc number ˆ! Folder number. To change the default display mode, press the AUDIO knob repeatedly until DISPLAY MODE appears on the display, then rotate the knob to select the following display modes: Disc number ˆ! Folder number. Once a display mode is selected, press the AU- DIO knob again to store the setting. c Folder number mode displays the selected folder number and the track number that is currently being played.

c Disc number mode displays the selected disc number and the track number that is currently being played.

c Artist title mode displays the artist title of the

MP3/WMA file.

c Disc number mode displays the current disc

c Track title mode displays the track title of the

number playing in the changer.

MP3/WMA file.

c Folder title mode displays the folder name

given to the MP3 folder.

Display satellite radio display mode (if so equipped)

To change the text displayed when listening to satellite radio (if so equipped) press the DISP button. The DISP button will scroll through the broadcast information as follows: Name ˆ! Title ˆ! Current display mode. To change the default display mode press the AUDIO button to display mode and press the TUNE button to select the following display modes: Channel number ˆ! Channel name ˆ! Name ˆ! Title. Once the display mode is selected press the AUDIO button again to store the setting. If the AUDIO button is not pressed after 8 seconds the display will refresh with the last selected display mode setting. c Channel number mode displays the channel number of the selected satellite radio sta- tion.

c Channel name mode displays the channel name of the selected satellite radio station. c Name mode displays the name of the artist, host or weather condition of the selected satellite radio station.

c Title mode displays the song title, show name, or temperature of the selected satel- lite radio station.

Display screen, heater, air conditioner and audio systems 4-37

Z REVIEW COPY—2007 Pathfinder (pat) Owners Manual—USA_English (nna) 10/16/06—cathy X

FM/AM/SAT radio operation FM/AM/SAT band select:

Pushing the RADIO button will change the band as follows: AM ˆ! FM or SAT (satellite, if so equipped) When the RADIO button is pushed while the ignition switch is in the ACC or ON position, the radio will come on at the station last played.

The last station played will also come on when the POWER/VOLUME control knob is de- pressed to ON.

No satellite radio reception is available when the RADIO button is pressed to access satellite radio stations unless optional satellite receiver and an- tenna are installed and an XMT or SIRIUS(cid:153) sat- ellite radio service subscription is active. Satellite radio can only be installed in vehicles that were factory pre-wired for satellite radio. Satellite radio is not available in Alaska, Hawaii and Guam. If satellite radio is not operational then the RADIO button is used to toggle between AM and FM bands.

The FM stereo indicator ST will glow during FM stereo reception. When the stereo broadcast signal is weak, the radio will automatically change from stereo to monaural reception.

CAT FOLDER (tuning) button:

or

To manually tune the radio, press the CAT FOLDER button or turn the tun- ing knob to right or left. To move quickly through the channels, press and hold either the button down for or more than 1.5 seconds.

SEEK/TRACK tuning button:

or

Press the SEEK/TRACK button for less than 1.5 seconds to tune from high to low or low to high frequencies and stop at the next broadcasting station. To seek quickly through the channels, press and hold the SEEK/TRACK button for more than 1.5
seconds. When the button is released the radio will seek to the next broadcasting station. SCAN RPT tuning (Type A, B and D only): Press the SCAN RPT button for more than 1.5
seconds to stop at each broadcasting station (AM, FM or SAT if so equipped) for 5 seconds. Pressing the button again during this 5 second

period will stop scan tuning and the radio will remain tuned to that station. If the SCAN RPT button is not pressed within 5 seconds, scan tuning moves to the next station. PRESET A•B•C (Station memory opera- tions):

18 stations can be set for the FM, AM and SAT (satellite, if so equipped) radio to the A, B and C preset button in any combination of FM, AM or SAT stations.

1. Choose preset bank A, B or C using the

PRESET A•B•C select button.

2. Select the desired FM, AM or SAT station

band.

3. Tune to the desired station using manual, SEEK or SCAN tuning. Press and hold any of the desired station memory buttons (1 (cid:150) 6) until a beep sound is heard.

4. The channel indicator will then come on and the sound will resume. Programming is now complete.

5. Other buttons can be set in the same man-

ner.

If the battery cable is disconnected, or if the fuse opens, the radio memory will be canceled. In that case, reset the desired stations.

If a compact disc is playing when the RADIO button is pushed, the compact disc will automati- cally be turned off and the last radio station played will come on. 4-38 Display screen, heater, air conditioner and audio systems

Z REVIEW COPY—2007 Pathfinder (pat) Owners Manual—USA_English (nna) 10/16/06—cathy X

Radio data system (RDS):

RDS stands for Radio Data System, and is a data information service transmitted by some radio stations on the FM band (not AM band). Cur- rently, most RDS stations are in large cities, but many stations are now considering broadcasting RDS data.

RDS can display: c Station call sign, such as (cid:147)WHFR 98.3(cid:148). c Station name, such as (cid:147)The Groove(cid:148). c Music or programming type such as (cid:147)Clas-

sical(cid:148), (cid:147)Country(cid:148), or (cid:147)Rock(cid:148). c Artist and song information. If the station broadcasts RDS information, the RDS icon is displayed. Compact disc (CD) changer operation Turn the ignition key to the ACC or ON position and insert the compact disc into the slot with the label side facing up. The compact disc will be guided automatically into the slot and start play- LOAD ing. To insert the disc, first press the button.

If the radio is already operating, it will automati- cally turn off and the compact disc will play.

If the system has been turned off while the com- pact disc was playing, pressing the PWR/VOL control knob will start the compact disc.

Do not use 3.1 in (8 cm) diameter compact discs in the CD changer.

LOAD button:

To insert a CD in the CD changer, press the load for less than 1.5 seconds. Select button the loading slot by pressing the CD insert select button (1 (cid:150) 6), then insert the CD.

To insert 6 CDs to the CD changer, press the load button for more than 1.5 seconds.

The slot numbers (1 (cid:150) 6) will illuminate on the display when CDs are loaded into the changer. CD button:

When the CD button is pressed with the system off and the compact disc loaded, the system will turn on and the compact disc will start to play.

When the CD button is pressed with the com- pact disc loaded with the radio playing, the radio will automatically be turned off and the compact disc will start to play.

SEEK/TRACK button:

When the button is pressed for less than 1.5 seconds while a compact disc is playing, the track being played returns to its beginning. Press several times to skip back through tracks. The compact disc will go back the number of times the button is pressed. When the button is pressed for less than 1.5 seconds while the compact disc is playing, the next track will start to play from its beginning. Press several times to skip through tracks. The compact disc will advance the number of times the button is pressed. (When the last track on the compact disc is skipped through, the first track will be played.)

CAT FOLDER button:

While playing a CD, press the CAT FOLDER button or to fast forward or rewind a track on a CD.

Display screen, heater, air conditioner and audio systems 4-39

Z REVIEW COPY—2007 Pathfinder (pat) Owners Manual—USA_English (nna) 10/16/06—cathy X

REAR AV (if so equipped): Press the Rear AV button to toggle the radio between CD and DVD modes. When the radio goes into DVD mode and the DVD player is off the DVD player will turn on. When the DVD player is on radio or CD can be selected. The DVD player will remain on and broadcast audio through the headphones in the rear of the vehicle. The DVD player can be turned off from the radio by selecting the DVD mode and pushing the radio power button. The DVD player will turn off and the radio will go to the last selected mode. The DVD player can be operated by remote con- trol or by the DVD entertainment system located in the center console. CD EJECT:

All discs: c Press and hold the

button for more than 1.5 seconds. The compact discs will be ejected one by one. If a disc is not removed button is within 15 seconds, or the pressed again during the eject sequence, the entire disc eject sequence will be can- celed.

When this button is pressed while the compact disc is being played, the compact disc will eject and the last source will be played. CD IN indicator: The slot numbers (1 (cid:150) 6) will illuminate if CDs have been loaded into the changer in CD mode only.

MP3 CAT FOLDER button:

or

to fast forward or rewind a track on an

While playing an MP3 CD, press the CAT FOLDER button to scan back- ward or forward through available folders. Press and hold the CAT FOLDER button or MP3 CD. CD select buttons: To play another CD that has been loaded, press a CD select button (1 (cid:150) 6). SCAN/RPT: When the SCAN/RPT play button is pushed while the compact disc is played, the play pattern can be changed as follows: ALL DISC RPT ! 1 DISC RPT! 1 TRACK RPT ! ALL DISC RDM ! 1 DISC RDM ! ALL DISC RPT ALL DISC RPT: All discs loaded will be repeated. 1 DISC RPT: The disc that is currently playing will be repeated. 1 TRACK RPT: The track that is currently playing will be repeated ALL DISC RDM: Tracks from all discs will be played randomly 1 DISC RDM: Tracks from the disc that is cur- rently playing will be played randomly 4-40 Display screen, heater, air conditioner and audio systems

Current/Selected disc: c Press the

button, then press the slot number (1 (cid:150) 6) for the desired disc. The compact disc will be ejected. If no slot num- ber (1 (cid:150) 6) is pressed, the current loaded disc will be ejected. Also, if the ejected disc is not removed within 15 seconds, the disc will reload.

Z REVIEW COPY—2007 Pathfinder (pat) Owners Manual—USA_English (nna) 10/16/06—cathy X

LHA0733

AUX jack (if so equipped) The AUX jack s1 is located above the power outlet. The AUX audio input jack accepts any standard analog audio input such as from a por- table cassette tape player, MP3 player or laptop computers. Press the AUX button to play a compatible device when it is plugged into the AUX jack.

1. 2. 3. 4. 5.

SEEK/TRACK button TUNE/FOLDER•CAT button DISP button SCAN/RPT button PWR/VOL control knob

WHA0732

PRESET A•B•C select button Station and CD select (1 - 6) buttons

Type B 6. 7. 8. CD button 9. 10. SAT button*

FM•AM button

Display screen, heater, air conditioner and audio systems 4-41

Z REVIEW COPY—2007 Pathfinder (pat) Owners Manual—USA_English (nna) 10/16/06—cathy X

11. DVD button 12. AUX button 13. AUDIO and TUNE/TRACK control knob (BASS, MID, TREBLE, FADE and BAL- ANCE)

14. LOAD button 15. CD insert slot 16.

CD eject button

*No satellite radio reception is available when the RADIO button is pressed to access satellite radio stations unless optional satellite receiver and antenna are installed and an XMT or SIRIUS(cid:153) satellite radio service subscription is active. Satellite radio can only be in- stalled in vehicles that were factory pre- wired for satellite radio. Satellite radio is not available in Alaska, Hawaii and Guam.

stalled and an XMT or SIRIUS(cid:153) satellite radio service subscription is active. Satellite radio can only be installed in vehicles that were factory pre-wired for satellite radio. Satellite radio is not available in Alaska, Hawaii and Guam. Audio main operation POWER/VOLUME control:

Turn the ignition key to ACC or ON, and then press the PWR/VOL control knob while the sys- tem is off to call up the mode (radio or CD) which was playing immediately before the system was turned off.

To turn the system off, press the PWR/VOL con- trol knob.

Turn the PWR/VOL control knob to adjust the volume.

This vehicle may be equipped with Speed Sen- sitive Volume (SSV) for audio. The audio volume changes as the driving speed changes. AUDIO knob (BASS, MIDRANGE, TREBLE, FADE, BALANCE and SSV if so equipped):

FM/AM/SAT RADIO WITH COMPACT DISC CHANGER (if so equipped) Press the AUDIO knob to change the mode as No satellite radio reception is available and (cid:147)NO follows: BASS ! MID ! TREBLE ! FADE ! BALANCE SAT(cid:148) is displayed when the RADIO button is ! SSV (if so equipped) pressed to access satellite radio stations unless optional satellite receiver and antenna are in- 4-42 Display screen, heater, air conditioner and audio systems

To adjust Bass, Mid (Midrange), Treble, Fade and Balance, press the AUDIO knob until the desired mode appears in the display. Turn the Tuning knob to adjust Bass and Treble to the desired level. You can also use the Tuning knob to adjust Fader and Balance modes. Fader adjusts the sound level between the front and rear speakers and Balance adjusts the sound between the right and left speakers. To change the SSV mode to OFF, LOW, MID or HIGH, turn the Tuning knob to the right or left. Once you have adjusted the sound quality to the desired level, press the AUDIO knob repeatedly until the radio or CD display reappears. Other- wise, the radio or CD display will automatically reappear after about 10 seconds. Clock set For setting the clock, see (cid:147)Adjusting the time(cid:148) earlier in this section. DISP (display) button: This DISP (display) button will show text about MP3, SAT or CD information in the audio display. CD display mode To change the text displayed while playing a CD with text, press the DISP button. The DISP button will allow you to scroll through CD text as follows: Disc title ˆ! Track title.

Z REVIEW COPY—2007 Pathfinder (pat) Owners Manual—USA_English (nna) 10/16/06—cathy X

To change the default display mode, press the AUDIO knob repeatedly until DISPLAY MODE appears on the display, then rotate the knob to select the following display modes: Disc number ˆ! Folder number. Once the display mode is selected, press the AUDIO knob again to store the setting. If the AUDIO knob is not pressed within 8 seconds, the display will refresh with the last selected display mode setting. c Track title mode displays the title of the se-

lected CD track.

c Disc title mode displays the title of the CD

being played.

c Track number mode displays the number selected disc and the track that is currently being played on the disk.

c Disc number mode displays the current disc

number playing in the changer.

MP3 display mode

To change the text displayed when listening to an MP3/WMA CD with MP3/WMA text (when CD with text is being used), press the DISP button. The DISP button will scroll through the CD text as follows: Track title ˆ! Folder title ˆ! Artist title ˆ! Disc number ˆ! Folder number.

To change the default display mode, press the AUDIO knob repeatedly until DISPLAY MODE appears on the display, then rotate the knob to select the following display modes: Disc number ˆ! Folder number. Once a display mode is selected, press the AU- DIO knob again to store the setting. c Folder number mode displays the selected folder number and the track number that is currently being played.

c Disc number mode displays the selected disc number and the track number that is currently being played.

c Artist title mode displays the artist title of the

MP3/WMA file.

c Track title mode displays the track title of the

MP3/WMA file.

c Folder title mode displays the folder name

given to the MP3 folder.

Display satellite radio display mode (if so equipped)

To change the text displayed when listening to satellite radio (if so equipped) press the DISP button. The DISP button will scroll through the broadcast information as follows: Name ˆ! Title ˆ! Current display mode.

To change the default display mode press the AUDIO button to display mode and press the TUNE button to select the following display modes: Channel number ˆ! Channel name ˆ! Name ˆ! Title. Once the display mode is selected press the AUDIO button again to store the setting. If the AUDIO button is not pressed after 8 seconds the display will refresh with the last selected display mode setting. c Channel number mode displays the channel number of the selected satellite radio sta- tion.

c Channel name mode displays the channel name of the selected satellite radio station. c Name mode displays the name of the artist, host or weather condition of the selected satellite radio station.

c Title mode displays the song title, show name, or temperature of the selected satel- lite radio station.

FM/AM/SAT radio operation FM/AM/SAT band select: Pressing the FM•AM or SAT (satellite - if so equipped) radio select button will change the band as follows: AM ˆ! FM or SAT*

Display screen, heater, air conditioner and audio systems 4-43

Z REVIEW COPY—2007 Pathfinder (pat) Owners Manual—USA_English (nna) 10/16/06—cathy X

When FM•AM or SAT* radio select button is pressed while the ignition switch is in the ACC or ON, the radio will come on at the station last played.

The last station played will also come on when the POWER/VOLUME control knob is pressed ON.

*No satellite radio reception is available and (cid:147)NO SAT(cid:148) is displayed when the SAT button is pressed unless optional satellite receiver and antenna are installed, and an XMT or SIRIUS(cid:153) satellite radio service subscription is active. Sat- ellite radio is not available in Alaska, Hawaii and Guam.

If a compact disc is playing when the FM•AM or SAT* radio select button is pressed, the compact disc will automatically be turned off and the last radio station played will come on.

The FM stereo indicator ST will glow during FM stereo reception. When the stereo broadcast signal is weak, the radio will automatically change from stereo to monaural reception.

CAT FOLDER (tuning) button:

To move quickly through the channels, press and button down for or hold either the more than 1.5 seconds.

SEEK/TRACK tuning button:

Press the SEEK/TRACK button for less than 1.5 seconds to tune from high to low or low to high frequencies and stop at the next broadcasting station.

or

To seek quickly through the channels, press and hold the SEEK/TRACK button for more than 1.5
seconds. When the button is released the radio will seek to the next broadcasting station. SCAN RPT tuning (Type A, B and D only):

Press the SCAN RPT button for more than 1.5
seconds to stop at each broadcasting station (AM, FM or SAT if so equipped) for 5 seconds. Pressing the button again during this 5 second period will stop scan tuning and the radio will remain tuned to that station. If the SCAN RPT button is not pressed within 5 seconds, scan tuning moves to the next station.

To manually tune the radio, press the CAT FOLDER button or turn the tun- ing knob to right or left. 4-44 Display screen, heater, air conditioner and audio systems

or

PRESET A•B•C (Station memory opera- tions):

18 stations can be set for the FM, AM and SAT (satellite, if so equipped) radio to the A, B and C preset button in any combination of FM, AM or SAT stations.

1. Choose preset bank A, B or C using the

PRESET A•B•C select button.

2. Select the desired FM, AM or SAT station

band.

3. Tune to the desired station using manual, SEEK or SCAN tuning. Press and hold any of the desired station memory buttons (1 (cid:150) 6) until a beep sound is heard.

4. The channel indicator will then come on and the sound will resume. Programming is now complete.

5. Other buttons can be set in the same man-

ner.

If the battery cable is disconnected, or if the fuse opens, the radio memory will be canceled. In that case, reset the desired stations. Radio data system (RDS): RDS stands for Radio Data System, and is a data information service transmitted by some radio stations on the FM band (not AM band). Cur-

Z REVIEW COPY—2007 Pathfinder (pat) Owners Manual—USA_English (nna) 10/16/06—cathy X

rently, most RDS stations are in large cities, but many stations are now considering broadcasting RDS data.

RDS can display: c Station call sign, such as (cid:147)WHFR 98.3(cid:148). c Station name, such as (cid:147)The Groove(cid:148). c Music or programming type such as (cid:147)Clas-

sical(cid:148), (cid:147)Country(cid:148), or (cid:147)Rock(cid:148). c Artist and song information. If the station broadcasts RDS information, the RDS icon is displayed. Compact disc (CD) changer operation Turn the ignition key to the ACC or ON position and insert the compact disc into the slot with the label side facing up. The compact disc will be guided automatically into the slot and start play- ing. To insert the disc, first press the LOAD button. If the radio is already operating, it will automati- cally turn off and the compact disc will play. If the system has been turned off while the com- pact disc was playing, pressing the PWR/VOL control knob will start the compact disc. Do not use 3.1 in (8 cm) diameter compact discs in the CD changer.

LOAD button:

To insert a CD in the CD changer, press the LOAD button for less than 1.5 seconds. Select the loading slot by pressing the CD insert select button (1 (cid:150) 6), then insert the CD.

To insert 6 CDs to the CD changer, press the LOAD button for more than 1.5 seconds.

The slot numbers (1 (cid:150) 6) will illuminate on the display when CDs are loaded into the changer. CD button (Type B and C only):

When the CD button is pressed with the system off and the compact disc loaded, the system will turn on and the compact disc will start to play.

When the CD button is pressed with the com- pact disc loaded with the radio playing, the radio will automatically be turned off and the compact disc will start to play.

CAT FOLDER button:

While playing a CD, press the CAT FOLDER button or to fast forward or rewind a track on a CD.

MP3 CAT FOLDER button:

While playing an MP3 CD, press the CAT FOLDER button to scan back- ward or forward through available folders.

or

Press and hold the CAT FOLDER button or MP3 CD.

to fast forward or rewind a track on an

SEEK/TRACK:

When the button is pressed for less than 1.5 seconds while a compact disc is playing, the track being played returns to its beginning. Press several times to skip back through tracks. The compact disc will go back the number of times the button is pushed.

When the button is pressed for less than 1.5 seconds while the compact disc is playing, the next track will start to play from its beginning. Press several times to skip through tracks. The compact disc will advance the number of times the button is pressed. (When the last track on the compact disc is skipped through, the first track will be played.) CD select buttons: To play another CD that has been loaded, press a CD select button (1 (cid:150) 6).

Display screen, heater, air conditioner and audio systems 4-45

Z REVIEW COPY—2007 Pathfinder (pat) Owners Manual—USA_English (nna) 10/16/06—cathy X

When this button is pressed while the compact disc is being played, the compact disc will eject and the last source will be played. CD IN indicator: The slot numbers (1 (cid:150) 6) will illuminate if CDs have been loaded into the changer in CD mode only.

SCAN/RPT:

rear of the vehicle. The DVD player can be turned off from the radio by selecting the DVD mode and pushing the radio power button. The DVD player will turn off and the radio will go to the last selected mode.

The DVD player can be operated by remote con- trol or by the DVD entertainment system located in the center console. CD EJECT:

Current/Selected disc: c Press the

When the SCAN/RPT play button is pushed while the compact disc is played, the play pattern can be changed as follows: ALL DISC RPT ! 1 DISC RPT! 1 TRACK RPT ! ALL DISC RDM ! 1 DISC RDM ! ALL DISC RPT ALL DISC RPT: All discs loaded will be repeated. 1 DISC RPT: The disc that is currently playing will be repeated. 1 TRACK RPT: The track that is currently playing will be repeated ALL DISC RDM: Tracks from all discs will be played randomly 1 DISC RDM: Tracks from the disc that is cur- rently playing will be played randomly DVD button: When the DVD button is pushed with the system off and a DVD loaded in the DVD player, the DVD will start to play. When the DVD button is pushed with the DVD loaded with another audio source playing, the other source will automatically be turned off and the DVD will start to play. When the radio goes into DVD mode and the DVD player is off the DVD player will turn on. When the DVD player is on radio or CD can be selected. The DVD player will remain on and broadcast audio through the headphones in the 4-46 Display screen, heater, air conditioner and audio systems

All discs: c Press and hold the

button, then press the slot number (1 (cid:150) 6) for the desired disc. The compact disc will be ejected. If no slot num- ber (1 (cid:150) 6) is pressed, the current loaded disc will be ejected. Also, if the ejected disc is not removed within 15 seconds, the disc will reload.

button for more than 1.5 seconds. The compact discs will be ejected one by one. If a disc is not removed within 15 seconds, or the button is pressed again during the eject sequence, the entire disc eject sequence will be can- celed.

Z REVIEW COPY—2007 Pathfinder (pat) Owners Manual—USA_English (nna) 10/16/06—cathy X

c A new disc may be rough on the inner and outer edges. Remove the rough edges by rubbing the inner and outer edges with the side of a pen or pencil as illustrated.

LHA0733

LHA0049

AUX jack (if so equipped) The AUX jack s1 is located above the power outlet. The AUX audio input jack accepts any standard analog audio input such as from a por- table cassette tape player, MP3 player or laptop computers. Press the AUX button to play a compatible device when it is plugged into the AUX jack.

CD CARE AND CLEANING c Handle a CD by its edges. Do not bend the

disc. Never touch the surface of the disc.

c Always place the discs in the storage case

when they are not being used.

c To clean a disc, wipe the surface from the center to the outer edge using a clean, soft cloth. Do not wipe the disc using a circular motion.

c Do not use a conventional record cleaner or

alcohol intended for industrial use.

Display screen, heater, air conditioner and audio systems 4-47

Z REVIEW COPY—2007 Pathfinder (pat) Owners Manual—USA_English (nna) 10/16/06—cathy X

MODE select switch Push the mode select switch to change the mode in the following sequence: PRESET A ! PRE- SET B ! PRESET C ! CD* ! DVD (if so equipped) ! AUX**. *This mode is only available when a CD is loaded.

**This mode is only available when a compatible auxiliary device is plugged into the AUX jack. Volume control switch Push the volume control switch up or down to increase or decrease the volume.

Tuning

Memory change (radio):

Push the tuning switch ( than 1.5 seconds to change presets. Seek tuning (radio):

or

) for less

Push the tuning switch ( ) for more than 1.5 seconds to seek the next or previ- ous radio station. Next/Previous track (CD):

or

Push the tuning switch for less than 1.5 seconds to return to the beginning of the

or

present track or skip to the next track. Push several times to skip back or skip through tracks. Change disc (CD) (if so equipped): for or Push the SEEK tuning switch more than 1.5 seconds to change the playing disc up or down. ANTENNA Window antenna The antenna pattern is printed inside the rear passenger and driver side windows.

CAUTION

c Do not place metalized film near the rear driver or passenger side window glass or attach any metal parts to it. This may cause poor reception or noise.

c When cleaning the inside of the rear driver or passenger side window, be careful not to scratch or damage the window antenna. Lightly wipe along the antenna with a dampened soft cloth.

LHA0269

POWER on/off switch Tuning switch

Volume control switch 1. 2. MODE select switch 3. 4. STEERING WHEEL SWITCH FOR AUDIO CONTROL (if so equipped) The audio system can be operated using the controls on the steering wheel. POWER on/off switch With the ignition key turned to the ACC or ON position, push the POWER switch to turn the audio system on or off.

4-48 Display screen, heater, air conditioner and audio systems

Z REVIEW COPY—2007 Pathfinder (pat) Owners Manual—USA_English (nna) 10/16/06—cathy X

NISSAN MOBILE ENTERTAINMENT SYSTEM (MES) (if so equipped)

LHA0389

WARNING

c The Mobile Entertainment System is designed for rear seat passenger view- ing only.

c The driver must not attempt to operate the Mobile Entertainment System while the vehicle is in motion so that full at- tention may be given to vehicle operation.

CAUTION

c The glass screen on the liquid crystal display may break if hit with a hard or sharp object. If the glass breaks, do not touch the liquid crystalline material, which contains a small amount of mer- cury. In case of contact with skin, wash immediately with soap and water.

c Use a damp, soft cloth when cleaning the Mobile Entertainment System com- ponents. Do not use solvents or clean- ing solutions.

c Do not attempt to use the system in extreme temperature conditions [below -4(cid:176)F (-20(cid:176)C) or above 158(cid:176)F (70(cid:176)C)].

c To avoid draining the vehicle battery, do not operate the system more than 15
minutes without starting the engine.

Display screen, heater, air conditioner and audio systems 4-49

Z REVIEW COPY—2007 Pathfinder (pat) Owners Manual—USA_English (nna) 10/16/06—cathy X

LHA0316
DIGITAL VIDEO DISC (DVD) PLAYER CONTROLS Refer to (cid:147)Playing a digital video disc (DVD)(cid:148) later in this section for the function of each button.

EJECT button DVD slot ENTER button POWER on/off button

1. 2. 3. 4. 5. MODE button 6. 7. 8. 9. MENU button 10. DISPLAY button 11. NAVIGATION keys

Input jacks STOP button PLAY/PAUSE button

4-50 Display screen, heater, air conditioner and audio systems

LHA0317

1. 2. 3.

4. 5.

POWER button STOP button NEXT TRACK/CHAPTER and PREVI- OUS TRACK/CHAPTER button TITLE button ENTER button

Z REVIEW COPY—2007 Pathfinder (pat) Owners Manual—USA_English (nna) 10/16/06—cathy X

DISPLAY button

6. 7. MODE button SUBTITLE button 8. 9. AUDIO button 10. ANGLE button 11. CLEAR button 12. PAUSE button 13. PLAY button 14. FAST FORWARD/FAST REVERSE

button

15. MENU button 16. NAVIGATION keys 17. BACK button 18. NUMERIC KEYPAD REMOTE CONTROL Refer to (cid:147)Playing a digital video disc (DVD)(cid:148) later in this section for the function of each button.

c The screen rotates down to view and up into the housing to store when not in use. Ensure that the screen is latched securely into the housing when stored.

LHA0315

FLIP-DOWN SCREEN The flip-down screen has a wireless remote con- trol receiver s1 located at the bottom of the screen.

CAUTION

c The glass screen on the liquid crystal display may break if hit with a hard or sharp object. If the glass breaks, do not touch the liquid crystalline material, which contains a small amount of mer- cury. In case of contact with skin, wash immediately with soap and water.

Display screen, heater, air conditioner and audio systems 4-51

Z REVIEW COPY—2007 Pathfinder (pat) Owners Manual—USA_English (nna) 10/16/06—cathy X

PLAYING A DIGITAL VIDEO DISC (DVD)

CAUTION

c Only operate the DVD while the vehicle engine is running. Operating the DVD for extended periods of time with the engine OFF can discharge the vehicle battery.

c Do not allow the system to get wet. Excessive moisture such as spilled liq- uids may system to malfunction.

cause

the

c The driver must not attempt to wear the headphones while the vehicle is in mo- tion so that full attention may be given to vehicle operation.

c While playing video CD media, this DVD player does not guarantee complete functionality of all video CD formats.

With the DVD player, you can hear DVD videos, video CDs and CDs using headphones. Passen- gers in the rear seat can enjoy the sound inde- pendently of the front seat.

Press the DVD or CD/REAR AV button located