the is
windshield-washer empty.
● Do not fill the windshield-washer fluid reservoir with washer fluid concen- trates at full strength. Some methyl al- cohol based washer fluid concentrates may permanently stain the grille if spilled while filling the windshield- washer fluid reservoir.
● Pre-mix washer fluid concentrates with water to the manufacturer’s recom- mended levels before pouring the fluid into the windshield-washer fluid reser- voir. Do not use the windshield-washer fluid reservoir to mix the washer fluid and water.
REAR WINDOW AND OUTSIDE MIRROR (if so equipped) DEFROSTER SWITCH
Type A
Type B
LIC1387
LIC1388
NOTE: The top few rows of wires on the rear win- dow are not part of the rear window de- froster system. These wires make up the antenna for the audio system.
To defrost the rear window glass and outside mirrors (if so equipped), start the engine and push the rear window defroster switch on. The rear window defroster light on the switch comes on. Push the switch again to turn the defroster off.
indicator
The rear window defroster automatically turns off after approximately 15 minutes.
CAUTION
When cleaning the inner side of the rear window, be careful not to scratch or dam- age the rear window defroster.
HEADLIGHT AND TURN SIGNAL SWITCH
XENON HEADLIGHTS (if so equipped)
WARNING
cHIGH VOLTAGE
● When xenon headlights are on, they produce a high voltage. To prevent an electric shock, never attempt to modify or disassemble. Always have your xe- non headlights replaced at a NISSAN dealer.
● Xenon headlights provide considerably more light than conventional head- lights. If they are not correctly aimed, they might temporarily blind an oncom- ing driver or the driver ahead of you and cause a serious accident. If headlights are not aimed correctly, immediately take your vehicle to a NISSAN dealer and have the headlights adjusted correctly.
When the xenon headlight is initially turned on, its brightness or color varies slightly. However, the color and brightness will soon stabilize.
Instruments and controls 2-29
● The life of xenon headlights will be shortened by frequent on-off opera- tion. It is generally desirable not to turn off the headlights for short intervals (for example, when the vehicle stops at a traffic signal).
● If the xenon headlight bulb is close to burning out, the brightness will drasti- cally decrease, the light will start blink- ing, or the color of the light will be- come reddish. If one or more of the above signs appear, contact a NISSAN dealer.
2-30 Instruments and controls
Type A
Type B
WIC1435
WIC1436
HEADLIGHT CONTROL SWITCH Lighting 䊊1 When turning the switch to the
posi- tion, the front parking, tail, license plate and instrument panel lights come on. 䊊2 When turning the switch to the
posi- tion, the headlights come on and all the other lights remain on.
CAUTION
Use the headlights with the engine run- ning to avoid discharging the vehicle battery.
To turn on the autolight system: 1. Place the headlight switch in the AUTO po-
sition 䊊1 .
2. Place ignition in the ON position. 3. The autolight system automatically turns the
headlights on and off.
LIC1086
Autolight system The autolight system allows the headlights to be set so they turn on and off automatically. The autolight system can: ● Turn on the headlights, front parking, tail, license plate and instrument panel lights au- tomatically when it is dark.
● Turn off all the lights when it is light. ● Keep all the lights on for a period of time after you place the ignition switch in the OFF position and all doors are closed.
Initially, if the ignition switch is placed in the OFF position and a door is opened and left open, the headlights remain ON for a period of time. If another door is opened while the headlights are on, then the timer is reset. To turn the autolight system off, turn the switch to the OFF,
position.
, or
Instruments and controls 2-31
CAUTION
Even though the battery saver feature au- tomatically turns off the headlights after a period of time, you should turn the head- light switch to the OFF position when the engine is not running to avoid discharging the vehicle battery.
DAYTIME RUNNING LIGHT SYSTEM (Canada only) The headlights automatically illuminate at a re- duced intensity when the engine is started with the parking brake released. The daytime running lights operate with the headlight switch in the position. Turn the OFF position or in the position for full headlight switch to the illumination when driving at night.
If the parking brake is applied before the engine is started, the daytime running lights do not illumi- nate. The daytime running lights illuminate when the parking brake is released. The daytime run- ning lights will remain on until the ignition switch is placed in the OFF position.
WHA1170
Be sure you do not put anything on top of
the autolight sensor located on the top side
of the instrument panel. The autolight sen-
sor controls the autolight; if it is covered,
the autolight sensor reacts as if it is dark
out and the headlights will illuminate. If
this occurs while parked with the engine
off and the ignition switch placed in the ON
position, your vehicle’s battery could be-
come discharged.
2-32 Instruments and controls
WIC1438
Headlight beam select 䊊1 To select the high beam function, push the lever forward. The high beam lights come on and the
light illuminates.
䊊2 Pull the lever back to select the low beam. 䊊3 Pulling and releasing the lever flashes the
headlight high beams on and off.
Battery saver system If the ignition switch is placed in the OFF position while the headlight switch is in the or a period of time.
position, the headlights will turn off after
WARNING
When the daytime running light system is active, tail lights on your vehicle are not on. It is necessary at dusk to turn on your headlights. Failure to do so could cause an accident injuring yourself and others.
WIC1412
WIC1439
INSTRUMENT BRIGHTNESS CONTROL The instrument cluster illuminates when the igni- tion switch is in the ON position. The instrument brightness control operates when the the AUTO, Turn the control left or right to adjust the bright- ness of the instrument panel lights when driving at night. The instrument brightness control will not adjust the brightness when the headlights or parking lights are off.
headlight or
position.
control
switch
in
is
TURN SIGNAL SWITCH Turn signal 䊊1 Move the lever up or down to signal the turning direction. When the turn is com- pleted, the turn signals cancel automatically.
Lane change signal 䊊2 To signal a lane change, move the lever up or down to the point where the indicator light begins to flash, but the lever does not latch.
Instruments and controls 2-33
HAZARD WARNING FLASHER SWITCH
The flashers will operate with the ignition switch placed in any position. Some state laws may prohibit the use of the hazard warning flasher switch while driving.
LIC0394
Push the switch on to warn other drivers when
you must stop or park under emergency condi-
tions. All turn signal lights flash.
WARNING
● If stopping for an emergency, be sure to
move the vehicle well off the road.
● Do not use the hazard warning flashers while moving on the highway unless unusual circumstances force you to drive so slowly that your vehicle might become a hazard to other traffic.
● Turn signals do not work when the haz-
ard warning flasher lights are on.
position.
WIC1440
FOG LIGHT SWITCH (if so equipped)
To turn the fog lights on, turn the headlight switch
position, then turn the fog light
to the
switch to the
To turn the fog lights on with the headlight switch in
the AUTO position, the headlights must be on, then
turn the fog light switch to the
To turn the fog lights off, turn the fog light switch
to the OFF position.
The headlights must be on and the low beams
selected for the fog lights to operate. The fog
lights automatically turn off when the high beam
headlights are selected.
2-34 Instruments and controls
position.
HORN
HEATED SEATS (if so equipped)
LIC1389
To sound the horn, push near the horn icon of the
steering wheel.
LIC1543
The front seats are warmed by built-in heaters.
The switch is located on the center console.
WARNING
1. Start the engine.
Do not disassemble the horn. Doing so could affect proper operation of the supplemental front air bag system. Tam- pering with the supplemental front air bag system may result in serious personal injury.
2. Push the LO or HI position of the switch, as desired. The indicator light in the switch will illuminate.
The heater is controlled by a thermostat, automatically turning the heater on and off. The indicator light will remain on as long as the switch is on.
3. When the seat is warmed or before you leave the vehicle, be sure to turn the switch off.
WARNING
Do not use or allow occupants to use the seat heater if you or the occupants cannot monitor elevated seat temperatures or have an inability to feel pain in body parts that contact the seat. Use of the seat heater by such people could result in se- rious injury.
CAUTION
● Do not use the seat heater for extended periods or when no one is using the seat.
● Do not put anything on the seat which insulates heat, such as a blanket, cush- ion, seat cover, etc. Otherwise, the seat may become overheated.
● Do not place anything hard or heavy on the seat or pierce it with a pin or similar object. This may result in damage to the heater.
● Any liquid spilled on the heated seat should be removed immediately with a dry cloth.
● When cleaning the seat, never use gasoline, benzine, thinner, or any simi- lar materials.
Instruments and controls 2-35
CLIMATE CONTROL SEAT SWITCH (if so equipped)
● If any malfunctions are found or the heated seat does not operate, turn the switch off and have the system checked by your NISSAN dealer.
● The battery could run down if the seat heater is operated while the engine is not running.
LIC1410
The climate controlled seat warms up or cools
down the front seat by blowing warm or cool air
from the surface of the seat. The climate control
switch is located on the center console.
The climate controlled seat can be operated as follows:
1. Start the engine.
2. Turn the control knob to the H (Heat) side or to the C (Cool) side, as desired. The indica- tor light on the control knob will illuminate.
3. Adjust the desired amount of air using the control knob. The climate controlled seat blower remains on low speed for approxi-
2-36 Instruments and controls
mately 60 seconds after turning the switch on or selecting the desired temperature.
4. When the vehicle’s interior is warmed or cooled, or before you leave the vehicle, be sure to turn the control knob to the Off (center) position
To check the air filter for the climate controlled seat, contact a NISSAN dealer.
WARNING
Do not use or allow occupants to use the seat heater if you or the occupants cannot monitor elevated seat temperatures or have an inability to feel pain in body parts that contact the seat. Use of the seat heater by such people could result in se- rious injury.
CAUTION
● The battery could run down if the cli- mate control seat is operated while the engine is not running.
● Do not use the climate control seat for extended periods or when no one is using the seat.
● Do not put anything on the seat which insulates heat, such as a blanket, cush- ion, seat cover, etc. Otherwise, the seat may become overheated.
● Do not place anything hard or heavy on the seat or pierce it with a pin or similar objects. This may result in damage to the climate controlled seat.
● Any liquid spilled on the seat should be
removed immediately with a dry cloth
● The climate controlled seat has an air filter. Do not operate the climate con- trolled seat without an air filter. This may result in damage to the system.
● When cleaning the seat, never use gasoline, benzine, thinner, or any simi- lar materials.
● If any malfunctions are found or the climate controlled seat does not oper- ate, turn the switch off and have the system checked by your NISSAN dealer.
HEATED STEERING WHEEL (if so equipped)
NOTE: If the surface temperature of the steering wheel is above 68°F (20°C) when the switch is turned on, the system will not heat the steering wheel. This is not a malfunction.
LIC0421
The heated steering wheel system is designed to
operate only when the surface temperature of the
steering wheel is below 68°F (20°C).
Push the heated steering wheel switch to warm the steering wheel after the engine starts. The indicator light will come on.
If the surface temperature of the steering wheel is below 68°F (20°C), the system will heat the steering wheel and cycle off and on to maintain a temperature above 68°F (20°C). The indicator light will remain on as long as the system is on. Push the switch again to turn the heated steering wheel system off manually. The indicator light will go off.
Instruments and controls 2-37
VEHICLE DYNAMIC CONTROL (VDC) OFF SWITCH
POWER OUTLET
LIC1392
Front center console
The power outlets are for powering electrical accessories such as cellular telephones. They are rated at 12 Volt, 120 W (10A) maximum. The power outlet in the front console box is powered directly by the vehicle battery. The out- let on the center console near the shift selector is powered only when the ignition switch is in the ACC or ON position.
LIC1548
The vehicle should be driven with the Vehicle
Dynamic Control (VDC) system on for most driv-
ing conditions.
If the vehicle is stuck in mud or snow, the VDC
system reduces the engine output to reduce
wheel spin. The engine speed will be reduced
even if the accelerator is depressed to the floor. If
maximum engine power is needed to free a stuck
vehicle, turn the VDC system off.
To turn off the VDC system, push the VDC OFF
switch. The
Push the VDC OFF switch again or restart the
engine to turn on the system. See “Vehicle Dy-
namic Control (VDC) system” in the “Starting and
driving” section.
2-38 Instruments and controls
indicator will come on.
CAUTION
● The outlet and plug may be hot during
or immediately after use.
● The power outlets are not designed for
use with a cigarette lighter.
● Do not use with accessories that ex- ceed a 12 volt, 120W (10A) power draw. Do not use double adapters or more than one electrical accessory.
● Use power outlets with the engine run- ning to avoid discharging the vehicle battery.
● Avoid using power outlets when the air conditioner, headlights or rear window defroster is on.
● Before inserting or disconnecting a plug, be sure the electrical accessory being used is turned OFF.
● Push the plug in as far as it will go. If good contact is not made, the plug may overheat or the internal temperature fuse may open.
● When not in use, be sure to close the cap. Do not allow water or any other liquids to contact the outlet.
STORAGE
MAP POCKETS
LIC1393
LIC0016
WIC1551
SEATBACK POCKETS The seatback pockets are located on the back of the driver’s and passenger’s seats. The pockets can be used to store maps.
SUNGLASSES HOLDER To open the sunglasses holder, push and release. Only store one pair of sunglasses in the holder.
WARNING
Keep the sunglasses holder closed while driving to prevent an accident.
Instruments and controls 2-39
CAUTION
● Do not use for anything other than
sunglasses.
● Do not leave sunglasses in the sun- glasses holder while parking in direct sunlight. The heat may damage the sunglasses.
To open the front cup holders, push the cup holder lid. To close, lower the cup holder lid and push down until it clicks in place. The rear cup holders are located in the fold-down armrest in the rear seat back.
CUP HOLDERS
Front
LIC1395
CAUTION
● Avoid abrupt starting and braking when the cup holder is being used to prevent spilling the drink. If the liquid is hot, it can scald you or your passenger.
● Use only soft cups in the cup holder. Hard objects can injure you in an accident.
2-40 Instruments and controls
LIC0423
WIC1216
Rear
To open the cup holders on the rear fold-down armrest, lift the cup holder lid. To close, lower the lid.
Soft bottle holder
Soft bottle holder
CAUTION
● Do not use bottle holder for any other objects that could be thrown about in the vehicle and possibly injure people during sudden braking or an accident. ● Do not use bottle holder for open liquid
containers.
LIC1396
GLOVE BOX
Open the glove box by pulling the handle. Use the
mechanical key when locking 䊊1 or unlocking 䊊2
the glove box.
WARNING
Keep glove box lid closed while driving to help prevent injury in an accident or a sudden stop.
Instruments and controls 2-41
WIC1120
WIC1121
LIC0748
CONSOLE BOX Upper half Pull up on the driver’s side latch to open the upper half of the console box. The upper half of the console box may be used for storage of cellular phones. An access hole is provided at the front of the upper half of the console box for a phone or iPod姞 cord routing to the power outlet.
Lower half Pull up on the lever to open the lower half of the console box. A power outlet is located inside the console box and there is storage for compact discs.
GROCERY HOOKS The grocery hooks are located in the trunk and can be used to hang a standard size plastic grocery bag.
CAUTION
Do not apply a total load of more than 20
lbs (9 kg) to a single grocery hook.
2-42 Instruments and controls
LIC0802
To install a cargo net, attach the net to the retain-
ers.
To remove a cargo net, detach the net from the
retainers.
LIC1226
CARGO NET (if so equipped)
WARNING
● Properly secure all cargo with ropes or straps to help prevent it from sliding or shifting. In a sudden stop or collision, unsecured cargo could cause personal injury.
The cargo net helps keep packages in the cargo area from moving around while the vehicle is in motion.
WINDOWS
POWER WINDOWS
WARNING
● Make sure that all passengers have their hands, etc. inside the vehicle while it is in motion and before closing the windows. Use the window lock switch to prevent unexpected use of the power windows.
● Do not leave children unattended inside the vehicle. They could unknowingly ac- tivate switches or controls and become trapped in a window. Unattended chil- dren could become involved in serious accidents.
The power windows operate when the ignition switch is placed in the ON position, or for a period of time after the ignition switch is placed in the OFF position. If the driver’s or passenger’s door is opened during this period of time, the power to the windows is canceled.
Instruments and controls 2-43
Driver’s side power window switch The driver’s side control panel is equipped with switches to open or close all of the windows. To open a window, push the switch to the first detent and continue to hold down until the de- sired window position is reached. To close a window, pull the switch to the first detent and continue to hold up until the desired window position is reached.
WIC1124
1. Window lock button 2. 3.
Power door lock switch Front passenger’s side automatic win- dow switch Right rear passenger’s side window switch (automatic if so equipped) Left rear passenger’s side window switch (automatic if so equipped) Driver’s side automatic window switch
4.
5.
6.
2-44 Instruments and controls
WIC1265
Front passenger’s power window switch The passenger’s window switch operates only the corresponding passenger’s window. To open the window, push the switch to the first detent and continue to hold it down until the desired position is reached 䊊1 . To close the window, pull the switch to the first detent and continue to hold up until the desired window position is reached 䊊2 .
LIC0718
LIC0410
Rear power window switch The rear power window switches open or close only the corresponding windows. To open the window, push the switch to the first detent and continue to hold it down until the desired window position is reached 䊊1 . To close the window, pull the switch to the first detent and continue to hold up until the desired window position is reached 䊊2 . Locking passengers’ windows When the window lock button is depressed, only the driver’s side window can be opened or closed. Push it again to cancel the window lock function.
Automatic operation To fully open a window equipped with automatic operation, press the window switch down (only driver’s side shown) to the second detent and release it; it need not be held. The window auto- matically opens all the way. To stop the window, lift the switch up while the window is opening.
To fully close a window equipped with automatic operation, pull the switch up to the second detent and release it; it need not be held. To stop the window, press the switch down while the window is closing.
Auto-reverse function The auto-reverse function can be activated when a window is closed by automatic operation. Depending on the environment or driving conditions, the auto-reverse function may be activated if an impact or load similar to something being caught in the window oc- curs.
WARNING
There are some small distances immedi- ately before the closed position which cannot be detected. Make sure that all passengers have their hands, etc., inside the vehicle before closing the window.
If the vehicle’s battery is disconnected, replaced, or jump started, the power window auto-reverse function may not operate properly. If this occurs, please contact to re-initialize the power window auto-reverse system.
the dealer
If the control unit detects something caught in a window equipped with automatic operation as it is closing, the window will be immediately low- ered.
Instruments and controls 2-45
If the windows do not close automatically If the power window automatic function (closing only) does not operate properly, perform the fol- lowing procedure to initialize the power window system. 1. Place the ignition switch in the ON position. 2. Close the door. 3. Open the window more than halfway by
operating the power window switch.
4. Pull the power window switch and hold it to close the window, and then hold the switch for more than 3 seconds after the window is closed completely.
5. Release the power window switch. Operate the window by automatic function to confirm the initialization is complete.
6. Perform steps 2 through 5 above for other
windows.
If the power window automatic function does not operate properly after performing the above pro- cedure, have your vehicle checked by a NISSAN dealer.
2-46 Instruments and controls
MOONROOF (if so equipped)
LIC1408
AUTOMATIC MOONROOF The moonroof will only operate when the ignition switch is placed in the ON position. The auto- matic moonroof is operational for a period of time, even if the ignition switch is placed in the ACC or OFF position. If the driver’s door or the front passenger’s door is opened during this period of time, the power to the moonroof is canceled. Sliding the moonroof To fully open the moonroof, push the switch toward To fully close the moonroof, push the switch toward
䊊1 .
䊊2 .
To open or close the moonroof part way, push the switch in any direction while the moonroof is sliding to stop it in the desired position. Tilting the moonroof Close the moonroof by pushing the switch 䊊2 . Release the switch, then push toward 䊊2 again to tilt the the switch toward moonroof up. To tilt toward
the moonroof down, push the switch
䊊1 .
WARNING
● In an accident you could be thrown from the vehicle through an open moonroof. Always use seat belts and child restraints.
● Do not allow anyone to stand up or extend any portion of their body out of the moonroof opening while the vehicle is in motion or while the moonroof is closing.
CAUTION
When closing:
● Remove water drops, snow, ice or sand
from the moonroof before opening.
● Do not place heavy objects on the
moonroof or surrounding area.
Auto-reverse function (when closing or tilting down the moonroof) The auto-reverse function can be activated when the moonroof is closed or tilted down by auto- matic operation when the ignition switch is placed in the ON position or for a period of time after the ignition switch is placed in the OFF position. Depending on the environment or driving conditions, the auto-reverse function may be activated if an impact or load similar to something being caught in the moonroof occurs.
WARNING
There are some small distances immedi- ately before the closed position which cannot be detected. Make sure that all passengers have their hands, etc., inside the vehicle before closing the moonroof.
If the control unit detects something caught in the moonroof as it moves to the front, the moonroof will immediately open backward. When tilting down:
If the control unit detects something caught in the moonroof as it tilts down, the moonroof will im- mediately tilt up.
If the auto-reverse function malfunctions and re- peats opening or tilting up the moonroof, keep pushing the tilt down switch within 5 seconds after it happens; the moonroof will fully close gradually. Make sure nothing is caught in the moonroof.
WARNING
● In an accident you could be thrown from the vehicle through an open moonroof. Always use seat belts and child restraints.
● Do not allow anyone to stand up or extend any portion of their body out of the moonroof opening while the vehicle is in motion or while the moonroof is closing.
CAUTION
● Remove water drops, snow, ice or sand
from the moonroof before opening.
● Do not place heavy objects on the
moonroof or surrounding area.
Sunshade Open and close the sunshade by sliding it for- ward or backward. If the moonroof does not close Have your NISSAN dealer check and repair the moonroof.
Instruments and controls 2-47
DUAL PANEL MOONROOF (if so equipped)
LIC1411
AUTOMATIC MOONROOF The moonroof will only operate when the ignition switch is in the ON position. The automatic moonroof is operational for a period of time, even if the ignition switch is placed in the ACC or OFF position. If the driver’s door or the front passen- ger’s door is opened during this period of time, the power to the moonroof is canceled.
2-48 Instruments and controls
Sliding the moonroof To slide the moonroof: ● To fully open the moonroof, push the switch 䊊1 toward the open position until it reaches is the second detent. pushed to the first detent, only the sunshade will open.
the switch 䊊1
If
● To fully close the moonroof, push the switch 䊊2 toward the close position until it reaches is the second detent. pushed to the first detent, the moonroof will close but the sunshade will remain open.
the switch 䊊2
If
● To open or close the moonroof part way, release the switch 䊊1 or 䊊2 while the moon- roof is sliding open or closed. The moonroof will stop at the desired position.
Tilting the moonroof To tilt the moonroof: ● To tilt the moonroof up, push and release the tilt switch 䊊3 . When the moonroof is open, it will automatically close and then tilt up.
● To tilt the moonroof down, push and release
the tilt switch 䊊3 or push the switch 䊊2
toward the close position until it reaches the
first detent.
● To tilt the moonroof down and close the sunshade at the same time, push the switch 䊊2 to the close position until it reaches the second detent.
Auto-reverse function (when closing or tilting down the moonroof) The auto-reverse function can be activated when the moonroof is closed or tilted down by auto- matic operation when the ignition switch is placed in the ON position or for a period of time after the ignition switch is placed in the OFF position. Depending on the environment or driving conditions, the auto-reverse func- tion may be activated if an impact or load similar to something being caught in the moonroof occurs.
WARNING
There are some small distances immedi- ately before the closed position which cannot be detected. Make sure that all passengers have their hands, etc., inside the vehicle before closing the moonroof.
CAUTION
● Remove water drops, snow, ice or sand
from the moonroof before opening.
● Do not place heavy objects on the
moonroof or surrounding area.
When closing:
If the control unit detects something caught in the moonroof as it moves to the front, the moonroof will immediately open backward. When tilting down:
If the control unit detects something caught in the moonroof as it tilts down, the moonroof will im- mediately tilt up.
If the auto-reverse function malfunctions and re- peats opening or tilting up the moonroof, keep pushing the tilt down switch within 5 seconds after it happens; the moonroof will fully close gradually. Make sure nothing is caught in the moonroof.
WARNING
● In an accident you could be thrown from the vehicle through an open moonroof. Always use seat belts and child restraints.
● Do not allow anyone to stand up or extend any portion of their body out of the moonroof opening while the vehicle is in motion or while the moonroof is closing.
WIC1445
Sunshade To open the sunshade: ● To fully open the sunshade, push the switch 䊊1 toward the open position until it reaches the first detent.
● To fully open the sunshade and the moon- roof together, push the switch 䊊1 toward the open position until it reaches the second detent.
Instruments and controls 2-49
REAR POWER SUN SHADE (if so equipped)
To close the sunshade: ● To fully close the sunshade, push the switch 䊊2 toward the close position until it reaches the second detent.
● Pushing the switch 䊊2 to the first detent will
close the moonroof only.
If the moonroof does not close Have your NISSAN dealer check and repair the moonroof.
WIC1443
The rear sun shade operates when the ignition
switch is in the ACC or ON position.
The rear sun shade switch is located on the front console. ● To raise the sun shade, push the upper side
of the switch 䊊1 .
● To lower the sun shade, push the lower side
of the switch 䊊2 .
● The switch need not be held down.
2-50 Instruments and controls
CAUTION
● Do not place objects (such as newspa- pers, handkerchiefs, etc.) on the screen inlet port. Doing so may entangle these objects in the screen when it is extend- ing or retracting, causing improper op- eration or damage to the screen.
● Do not push the sun shade arm with your hands, etc., as this may deform it. Improper operation or damage to the screen may result.
● Do not hang any object on the arm rail as this may result in improper operation or damage the screen.
● Do not forcefully pull the screen. Doing so may elongate the screen. Improper operation or damage to the screen may result.
● To avoid personal
injury, keep your hands, fingers and head away from the sun shade arm, arm rail and screen inlet port.
● Do not allow children near the rear sun
shade system. They could be injured.
● Do not pull or push the rear sun shade. This could cause improper operation or damage it.
INTERIOR LIGHT
NOTE: The footwell and doorstep lights illuminate when the driver and passenger doors are opened regardless of the interior light switch position. These lights will turn off automatically after a period of time while doors are open to prevent the battery from becoming discharged.
CAUTION
Do not use for extended periods of time with the engine stopped. This could result in a discharged battery.
● When the switch is in the center DOOR position 䊊2 , the front and rear personal lights will illuminate under the following con- ditions:
– Driver’s door is unlocked while the igni- tion switch is placed in the OFF position. Lights remain on for a period of time.
– Driver’s door is opened.
Lights remain on for a period of time after driver’s door is closed.
– Ignition switch is placed in the OFF posi-
tion.
The lights will go off when the ignition switch is in the ON position, or the driver’s door is closed and locked.
The lights will also go off after a period of time when all doors are open. ● When the switch is in the OFF position 䊊3 , lights will not
the front and rear personal illuminate, regardless of door position.
WIC1550
The interior light has a three-position switch and operates regardless of ignition switch position. ● When the switch is in the ON position 䊊1 , the front and rear personal lights will illumi- nate, regardless of door position. The light will go off after a period of time unless the ignition switch is placed in the ON position.
Instruments and controls 2-51
PERSONAL LIGHTS
MAP LIGHTS
WIC1476
CONSOLE LIGHT The console light will turn on whenever the park- ing lights or headlights are illuminated. The console light brightness can be adjusted with the illumination brightness control.
LIC1413
To turn on the personal lights, press and release
the switch 䊊1 .
To turn the personal lights off, press and release
the switch 䊊1 .
Models without moonroof
WIC1494
To turn the map lights on, press the switches. To turn them off, press the switches again.
CAUTION
Do not use for extended periods of time with the engine stopped. This could result in a discharged battery.
2-52 Instruments and controls
TRUNK LIGHT
Models with moonroof
WIC1494
LIC1409
Models with dual panel moonroof
The light illuminates when the trunk lid is opened. When the trunk lid is closed, the light goes off. The light will go off after a period of time if the trunk lid is left open, unless the ignition switch is in the ON position. For bulb replacement procedures, refer to “Exte- rior and interior lights” in the “Maintenance and do-it-yourself” section of this manual.
HOMELINK姞 UNIVERSAL TRANSCEIVER (if so equipped)
The HomeLink姞 Universal Transceiver provides a convenient way to consolidate the functions of up to three individual hand-held transmitters into one built-in device. HomeLink姞 Universal Transceiver: ● Will operate most Radio Frequency (RF) devices such as garage doors, gates, home and office lighting, entry door locks and se- curity systems.
● Is powered by your vehicle’s battery. No separate batteries are required. If the vehi- cle’s battery is discharged or is discon- nected, HomeLink姞 will retain all program- ming.
Once the HomeLink姞 Universal Transceiver is programmed, retain the original trans- mitter for future programming procedures (Example: new vehicle purchases). Upon sale of the programmed HomeLink姞 Universal Transceiver buttons should be erased for security purposes. For additional information, refer to “Program- ming HomeLink姞” later in this section.
the vehicle,
Instruments and controls 2-53
WARNING
● Do not use the HomeLink姞 Universal Transceiver with any garage door opener that lacks safety stop and re- verse features as required by federal safety standards. (These standards be- came effective for opener models manufactured after April 1, 1982). A ga- rage door opener which cannot detect an object in the path of a closing garage door and then automatically stop and reverse, does not meet current federal safety standards. Using a garage door opener without these features in- creases the risk of serious injury or death.
● During the programming procedure your garage door or security gate will open and close (if the transmitter is within range). Make sure that people or objects are clear of the garage door, gate, etc. that you are programming.
● Your vehicle’s engine should be turned off while programming the HomeLink姞 Universal Transceiver.
2-54 Instruments and controls
WIC0986
PROGRAMMING HOMELINK姞
1. To begin, press and hold the two outer
HomeLink姞 buttons (to clear the memory)
until the indicator light 䊊1 blinks (after 20
seconds). Release both buttons.
2. Position the end of the hand-held transmitter 1 - 3 inches (26 - 76 mm) away from the HomeLink姞 surface.
WIC0987
3. Using both hands, simultaneously press and
hold both the HomeLink姞 button you want to
program and the hand-held transmitter but-
ton.
DO NOT release the buttons until step 4 has been completed.
4. Hold down both buttons until the indicator light on the HomeLink姞 flashes, changing from a “slow blink” to a “rapidly flashing blink”. This could take up to 90 seconds. When the indicator light flashes rapidly, both buttons may be released. The rapidly flash- ing light indicates successful programming. To activate the garage door or other pro-
5.
grammed device, press and hold the pro- grammed HomeLink姞 button — releasing when the device begins to activate. If the indicator light on the HomeLink姞 blinks rapidly for 2 seconds and then turns solid, HomeLink姞 has picked up a “rolling code” garage door opener signal. You will need to proceed with the next steps to train the HomeLink姞 to complete the programming which may require a ladder and another per- son for convenience.
6. Press and release the “smart” or “learn” pro- gram button located on the garage door opener’s motor to activate the “training mode”. This button is usually located near the antenna wire that hangs down from the motor. If the wire originates from under a light lens, you will need to remove the lens to access the program button.
NOTE: Once you have pressed and released the program button on the garage door open- er’s motor and the “training light” is lit, you have 30 seconds in which to perform step 7. Use the help of a second person for conve- nience to assist when performing this step. 7. Within 30 seconds of pressing and releas- ing the garage door opener’s program but-
ton, quickly and firmly press and release the HomeLink姞 button you’ve just programmed. Press and release the HomeLink姞 button up to 3 times to complete the training.
8. Your HomeLink姞 button should now be pro- grammed. (To program the remaining HomeLink姞 buttons for additional door or gate openers, follow steps 2-4 only.)
all
previously
NOTE: Do not repeat step 1 unless you want to “clear” programmed HomeLink姞 buttons. If you have any questions or are having difficulty programming your HomeLink姞 buttons, refer to the HomeLink姞 web site at: www.homelink.com or call 1-800-355-3515. PROGRAMMING HOMELINK姞 FOR CANADIAN CUSTOMERS Prior to 1992, D.O.C. regulations required hand- held transmitters to stop transmitting after 2 sec- onds. To program your hand-held transmitter to HomeLink姞, continue to press and hold the HomeLink姞 button (see steps 2 - 4under “Pro- gramming HomeLink姞”) while you press and re- press (“cycle”) your hand-held transmitters every 2 seconds until the indicator light flashes rapidly (indicating successful programming).
NOTE:
When programming a garage door opener, etc., it is advised to unplug the device dur- ing the “cycling” process to prevent pos- sible damage to the garage door opener components. OPERATING THE HOMELINK姞 UNIVERSAL TRANSCEIVER The HomeLink姞 Universal Transceiver (once pro- grammed) may now be used to activate the ga- rage door, etc. To operate, simply press the ap- propriate programmed HomeLink姞 Universal Transceiver button. The red indicator light will illuminate while the signal is being transmitted. PROGRAMMING TROUBLE- DIAGNOSIS If the HomeLink姞 does not quickly learn the hand- held transmitter information: ● replace the hand-held transmitter batteries
with new batteries.
● position the hand-held transmitter with its from the
facing
away
battery HomeLink姞 surface.
area
● press and hold both the HomeLink姞 and hand-held transmitter buttons without inter- ruption.
Instruments and controls 2-55
● position the hand-held transmitter 1 - 3
inches (26 - 76 mm) away from the
HomeLink姞 surface. Hold the transmitter in
that position for up to 15 seconds.
If
HomeLink姞 is not programmed within that
time, try holding the transmitter in another
position – keeping the indicator light in view
at all times.
If you continue to have programming difficulties,
please contact the NISSAN Consumer Affairs
Department. The phone numbers are located in
the Foreword of this manual.
CLEARING THE PROGRAMMED
INFORMATION
Individual buttons cannot be cleared. However,
to clear all programming, press and hold the two
outside buttons and release when the indicator
light begins to flash (approximately 20 seconds).
REPROGRAMMING A SINGLE
HOMELINK姞 BUTTON
To reprogram a HomeLink姞 Universal Transceiver
button, complete the following.
1. Press and hold the desired HomeLink姞 but-
ton. Do not release the button until step 4
has been completed.
2-56 Instruments and controls
2. When the indicator light begins to flash
slowly (after 20 seconds), position the
hand-held transmitter 1 - 3inches (26 - 76
mm) away from the HomeLink姞 surface.
3. Press and hold the hand-held transmitter
button.
4. The HomeLink姞 indicator light will flash, first slowly and then rapidly. When the indicator light begins to flash rapidly, release both buttons.
The HomeLink姞 Universal Transceiver button has now been reprogrammed. The new device can be activated by pushing the HomeLink姞 button that was just programmed. This procedure will not affect any other programmed HomeLink姞 buttons. IF YOUR VEHICLE IS STOLEN If your vehicle is stolen, you should change the codes of any non-rolling code device that has been programmed into HomeLink姞. Consult the Owner’s Manual of each device or call the manu- facturer or dealer of those devices for additional information. When your vehicle is recovered, you will need to reprogram the HomeLink姞 Univer- sal Transceiver with your new transmitter information.
FCC Notice: For USA: This device complies with Part 15 of the FCC Rules. Operation is subject to the fol- lowing two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference re- ceived, including interference that may cause undesired operation. Note: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. For Canada: This device complies with RSS-210 of In- dustry Canada. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, in- cluding interference that may cause unde- sired operation of the device.
3 Pre-driving checks and adjustments
Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2
NISSAN Intelligent Key™ . . . . . . . . . . . . . . . . . . . . . . . . 3-2
NISSAN Vehicle Immobilizer System keys . . . . . . . . . 3-3
Doors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4
Locking with key. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4
Locking with inside lock knob . . . . . . . . . . . . . . . . . . . . 3-5
Locking with power door lock switch . . . . . . . . . . . . . 3-5
Automatic door locks . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-6
Child safety rear door lock. . . . . . . . . . . . . . . . . . . . . . . 3-6
NISSAN Intelligent Key™ . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-7
Operating range. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-9
Door locks/unlocks precaution . . . . . . . . . . . . . . . . . . . 3-9
NISSAN Intelligent Key™ Operation. . . . . . . . . . . . . . 3-10
How to use the remote keyless entry
function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-13
Warning signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-16
Troubleshooting guide . . . . . . . . . . . . . . . . . . . . . . . . . 3-17
Hood . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-18
Trunk lid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-18
Opener operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-19
Interior trunk lid release . . . . . . . . . . . . . . . . . . . . . . . . 3-20
Secondary trunk lid release (if so equipped) . . . . . . 3-20
Fuel-filler door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-21
Opening the fuel-filler door . . . . . . . . . . . . . . . . . . . . . 3-21
Fuel-filler cap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-21
Tilt/telescopic steering . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-23
Manual operation (if so equipped) . . . . . . . . . . . . . . . 3-24
Automatic operation (if so equipped). . . . . . . . . . . . . 3-24
Sun visors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-25
Vanity mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-25
Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-26
Automatic anti-glare rearview mirror . . . . . . . . . . . . . 3-26
Outside mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-28
Automatic drive positioner (if so equipped) . . . . . . . . . . 3-29
Memory storage function . . . . . . . . . . . . . . . . . . . . . . . 3-30
Entry/exit function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-31
System operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-31
KEYS
WPD0363
Two Intelligent Keys
1. 2. Mechanical keys with built-in transpon-
der chip (inside Intelligent Keys) Key number plate
3. NISSAN INTELLIGENT KEY™ Your vehicle can only be driven with the Intelligent Keys which are registered to your vehicle’s Intel- ligent Key system components and NISSAN Ve- hicle Immobilizer System components. Never leave these keys in the vehicle.
As many as 4 Intelligent Keys can be registered and used with one vehicle. The new keys must be registered by a NISSAN dealer prior to use with 3-2 Pre-driving checks and adjustments
● Do not strike the Intelligent Key sharply
against another object.
● Do not change or modify the Intelligent
Key.
● Wetting may damage the Intelligent Key. If the Intelligent Key gets wet, im- mediately wipe until it is completely dry. ● Do not place the Intelligent Key for an extended period in an area where tem- peratures exceed 140°F (60°C).
● Do not attach the Intelligent Key with a
key holder that contains a magnet.
● Do not place the Intelligent Key near equipment that produces a magnetic field, such as a TV, audio equipment and personal computers.
the Intelligent Key system and NISSAN Vehicle Immobilizer System of your vehicle. Since the registration process requires erasing all memory in the Intelligent Key components when register- ing new keys, be sure to take all Intelligent Keys that you have to the NISSAN dealer.
A key number plate is supplied with your keys. Record the key number and keep it in a safe place (such as your wallet), not in the vehicle. If you lose your keys, see a NISSAN dealer for duplicates by using the key number. NISSAN does not record key numbers so it is very important to keep track of your key number plate. A key number is only necessary when you have lost all keys and do not have one to duplicate from. If you still have a key, your NISSAN dealer can duplicate it.
CAUTION
Listed below are conditions or occur- rences which will damage the Intelligent Key: ● Do not allow the Intelligent Key, which contains electrical components, to come into contact with water or salt water. This could affect the system function.
● Do not drop the Intelligent Key.
CAUTION
Always carry the mechanical key installed in the Intelligent Key slot.
See “Doors” in this section and “Storage” in the “Instruments and controls” section of this manual. Valet hand-off When you have to leave a key with a valet, give them the Intelligent Key itself and keep the me- chanical key with you to protect your belongings. To prevent the glove box and the trunk from being opened during valet hand-off, follow the proce- dures below. 1. Push the trunk cancel switch to the OFF
position.
2. Remove the mechanical key from the Intelli-
gent Key.
SPA1951
Mechanical key The Intelligent Key contains the mechanical key, which can be used in case of a discharged bat- tery.
To remove the mechanical key, release the lock knob on the back of the Intelligent Key.
3. Lock the glove box and the trunk pass-
through with the mechanical key.
To install the mechanical key, firmly insert it into the Intelligent Key until the lock knob returns to the lock position.
The mechanical key can be used for operation in the same way as an ordinary key.
4. Hand the Intelligent Key to the valet and
keep the mechanical key with you.
See “Trunk lid” in this section, “Storage” in the “Instruments and controls” section and “Seats” in the “Safety — seats, seat belts and supplemental restraint system” section of this manual.
NISSAN VEHICLE IMMOBILIZER SYSTEM KEYS You can only drive your vehicle using the master keys which are registered to the NISSAN Vehicle Immobilizer System components in your vehicle. These keys have a transponder chip in the key head.
The master key can be used for all the locks.
To protect belongings when you leave a key with someone, give them the Intelligent Key only, not the mechanical key. Never leave these keys in the vehicle.
Additional or replacement keys:
If you still have a key, the key number is not
necessary when you need extra NISSAN Vehicle
Immobilizer System keys. Your dealer can dupli-
cate your existing key. As many as four NISSAN
Vehicle Immobilizer System keys can be used
with one vehicle. You should bring all NISSAN
Vehicle Immobilizer System keys that you have to
your NISSAN dealer for registration. This is be-
cause the registration process will erase the
memory of all key codes previously registered
into the NISSAN Vehicle Immobilizer System.
After the registration process, these components
will only recognize keys coded into the NISSAN
Vehicle Immobilizer System during registration.
Pre-driving checks and adjustments 3-3
Any key that is not given to your dealer at the time of registration will no longer be able to start your vehicle. Do not allow the immobilizer system key, which contains an electrical transponder, to come into contact with salt water. This could affect system function.
DOORS
When the doors are locked using one of the following methods, the doors can not be opened using the inside or outside door handles. The doors must be unlocked to open the doors.
WARNING
● Always have the doors locked while driving. Along with the use of seat belts, this provides greater safety in the event of an accident by helping to prevent persons from being thrown from the vehicle. This also helps keep children and others from unintentionally open- ing the doors, and will help keep out intruders.
● Before opening any door, always look
for and avoid oncoming traffic.
● Do not leave children unattended inside the vehicle. They could unknowingly ac- tivate switches or controls. Unattended children could become involved in seri- ous accidents.
3-4 Pre-driving checks and adjustments
Driver’s side
LPD0461
LOCKING WITH KEY The power door lock system allows you to lock or unlock all doors at the same time. Turning the key toward the front 䊊1 of the vehicle locks all doors. Turning the key one time toward the rear 䊊2 of the vehicle unlocks that door. From that position, returning the key to neutral 䊊3 (where the key can only be removed and inserted) and turning it toward the rear again within 60 seconds unlocks all doors 䊊4 .
Opening and closing windows The driver’s door key operation allows you to open and close windows equipped with auto- matic operation at the same time. ● To open the windows, turn the driver’s door key toward the rear of the vehicle for longer than 1 second after the door is unlocked. ● To close the windows, turn the driver’s door key toward the front of the vehicle for longer than 1 second after the door is locked.
Windows stop when the key cylinder is released.
Inside lock
WPD0291
LOCKING WITH INSIDE LOCK KNOB To lock the door without the key, move the inside lock knob to the lock position 䊊1 , then close the door. To unlock the door without the key, move the inside lock knob to the unlock position 䊊2 .
WPD0381
LOCKING WITH POWER DOOR LOCK SWITCH To lock all the doors without a key, push the door lock switch (driver’s or front passenger’s side) to the lock position 䊊1 . When locking the door this way, be certain not to leave the key inside the vehicle. To unlock all the doors without a key, push the door lock switch (driver’s or front passenger’s side) to the unlock position 䊊2 .
Pre-driving checks and adjustments 3-5
4. When activated, the hazard indicator will flash twice. When deactivated, the hazard indicator will flash once.
5. The ignition switch must be placed in the OFF and ON position again between each setting change.
When the automatic door unlock system is deac- tivated, the doors do not unlock when the ignition switch is placed in the OFF position. To unlock the door manually, use the inside lock knob or the power door lock switch (driver’s or front passen- ger’s side).
Lockout protection When the power door lock switch (driver’s or front passenger’s side) is moved to the lock position with the Intelligent Key in the port and any door open, all doors will lock and unlock automatically. With the Intelligent Key left in the vehicle (not in the Intelligent Key port) and any door open, all doors will unlock automatically and a chime will sound after the door is closed. AUTOMATIC DOOR LOCKS ● All doors lock automatically when the vehicle
speed reaches 15 MPH (24 km/h).
● All doors unlock automatically when the ig-
nition is placed in the OFF position.
The automatic unlock function can be de- activated or activated. To deactivate or acti- vate the automatic door unlock system, perform the following procedure:
1. Close all doors.
2. Place the ignition switch in the ON position.
3. Within 20 seconds of performing Step 2, push and hold the power door lock switch to position (UNLOCK) for more than the 5 seconds.
3-6 Pre-driving checks and adjustments
LIC0716
CHILD SAFETY REAR DOOR LOCK
Child safety locks help prevent the rear doors
from being opened accidentally, especially when
small children are in the vehicle.
The child safety lock levers are located on the
edge of the rear doors.
When the lever is in the unlock position 䊊1 , the
door can be opened from the outside or the
inside.
When the lever is in the LOCK position 䊊2 ,
the door can be opened only from the out-
side.
NISSAN INTELLIGENT KEY™
WARNING
CAUTION
● Radio waves could adversely affect electric medical equipment. Those who use a pacemaker should contact the electric medical equipment manufac- turer for the possible influences before use.
● The Intelligent Key transmits radio waves when the buttons are pushed. The FAA advises the radio waves may affect aircraft navigation and communi- cation systems. Do not operate the In- telligent Key while on an airplane. Make sure the buttons are not operated unin- tentionally when the unit is stored for a flight.
The Intelligent Key system can operate all the door locks using the remote controller function or pushing the request switch on the vehicle without taking the key out from a pocket or purse. The operating environment and/or conditions may af- fect the Intelligent Key system operation.
Be sure to read the following before using the Intelligent Key system.
● Be sure to carry the Intelligent Key with
you when operating the vehicle.
● Never leave the Intelligent Key in the
vehicle when you leave the vehicle.
The Intelligent Key is always communicating with the vehicle as it receives radio waves. The Intel- ligent Key system transmits weak radio waves. Environmental conditions may interfere with the operation of the Intelligent Key system under the following operating conditions. ● When operating near a location where strong radio waves are transmitted, such as a TV tower, power station and broadcasting station.
● When in possession of wireless equipment, such as a cellular telephone, transceiver, and CB radio.
● When the Intelligent Key is in contact with or
covered by metallic materials.
● When any type of radio wave remote control
is used nearby.
● When the Intelligent Key is placed near an electric appliance such as a personal com- puter.
● When the vehicle is parked near a parking
meter.
In such cases, correct the operating conditions before using the Intelligent Key function or use the mechanical key.
If
Although the life of the battery varies depending
on the operating conditions, the battery’s life is
approximately 2 years.
the battery is dis-
charged, replace it with a new one.
When the Intelligent Key battery is almost dis-
charged, insert the Intelligent Key into the Intelli-
gent Key port to start the engine. Replace the
discharged battery with a new one as soon as
possible. For additional
information, see “Push
Button Ignition Switch “ in the “Starting and
Driving” section.
Since the Intelligent Key is continuously receiving
radio waves,
if the key is left near equipment
which transmits strong radio waves, such as sig-
nals from a TV and personal computer, the bat-
tery life may become shorter.
For information regarding replacement of a bat-
tery, see “Battery replacement” in the “Mainte-
nance and do-it-yourself” section.
As many as four Intelligent Keys can be regis-
tered and used with one vehicle. For information
about the purchase and use of additional Intelli-
gent Keys, contact a NISSAN dealer.
Pre-driving checks and adjustments 3-7
If an Intelligent Key is lost or stolen, NISSAN recommends erasing the ID code of that Intelli- gent Key from the vehicle. This may prevent the unauthorized use of the Intelligent Key to operate the vehicle. For information regarding the erasing procedure, contact a NISSAN dealer.
CAUTION
Listed below are conditions or occur- rences which will damage the Intelligent Key: ● Do not allow the Intelligent Key, which contains electrical components, to come into contact with water or salt water. This could affect the system function.
● Do not drop the Intelligent Key. ● Do not strike the Intelligent Key sharply
against another object.
● Do not change or modify the Intelligent
Key.
● Wetting may damage the Intelligent Key. If the Intelligent Key gets wet, im- mediately wipe until it is completely dry. ● Do not place the Intelligent Key for an extended period in an area where tem- peratures exceed 140°F (60°C).
● Do not attach the Intelligent Key with a
key holder that contains a magnet.
● Do not place the Intelligent Key near equipment that produces a magnetic field, such as a TV, audio equipment and personal computers.
3-8 Pre-driving checks and adjustments
SPA2038
If the Intelligent Key is too close to the door glass,
handle or rear bumper, the request switches may
not function.
When the Intelligent Key is within the operating
range, it is possible for anyone, even someone
who does not carry the Intelligent Key, to push the
request switch to lock/unlock the doors.
OPERATING RANGE The Intelligent Key functions can only be used when the Intelligent Key is within the specified operating range from the request switch 䊊1 . When the Intelligent Key battery is discharged or strong radio waves are present near the operat- ing location, the Intelligent Key operating range becomes narrower, and the Intelligent Key may not function properly.
The operating range is within 31.50 in (80 cm) from each request switch 䊊1 .
WPD0375
DOOR LOCKS/UNLOCKS PRECAUTION ● Do not push the door handle request switch with the Intelligent Key held in your hand as illustrated. The close distance to the door handle will cause the Intelligent Key system to have difficulty recognizing that the Intelli- gent Key is outside the vehicle.
● After locking with the door handle request switch, verify the doors are securely locked by testing them.
Pre-driving checks and adjustments 3-9
● To prevent the Intelligent Key from being left inside the vehicle, make sure you carry the Intelligent Key with you and then lock the doors.
● Do not pull the door handle before pushing the door handle request switch. The door will be unlocked but will not open. Release the door handle once and pull it again to open the door.
3-10 Pre-driving checks and adjustments
WPD0376
WPD0377
NISSAN INTELLIGENT KEY™ OPERATION You can lock or unlock the doors without taking the Intelligent Key out of your pocket or bag. When you carry the Intelligent Key with you, you can lock or unlock all doors by pushing the door handle request switch within the range of opera- tion.
Locking doors 1. Move the shift selector to the “P” position. Place the ignition switch in the LOCK posi- tion. Make sure the Intelligent Key is not left in the vehicle.
2. Close all doors.
3. Push any door handle request switch 䊊1
while carrying the Intelligent Key with you.
4. All doors and the trunk will lock.
5. The hazard warning lights flash twice and
the outside buzzer sounds twice.
● Doors do not lock with the door handle request switch with the Intelligent Key inside the vehicle and a beep sounds to warn you. However, when an Intelligent Key is inside the vehicle, doors can be locked with an- other Intelligent Key.
CAUTION
● After locking the doors using the re- quest switch, make sure that the doors have been securely locked by operating the door handles or the trunk opener switch.
● When locking the doors using the re- quest switch, make sure to have the Intelligent Key in your possession be- fore operating the request switch to prevent the Intelligent Key from being left in the vehicle.
● The request switch is operational only when the Intelligent Key has been de- tected by the Intelligent Key system.
Lockout protection To prevent the Intelligent Key from being acci- dentally locked in the vehicle, lockout protection is equipped with the Intelligent Key. When the driver’s side door is open, the doors are locked, and then the Intelligent Key is put
inside the vehicle and all the doors are closed; the lock will automatically unlock and the door buzzer sounds.
NOTE: The doors may not lock when the Intelli- gent Key is in the same hand that is oper- ating the request switch to lock the door. Put the Intelligent Key in a purse, pocket or your other hand.
CAUTION
The lockout protection may not function under the following conditions: ● When the Intelligent Key is placed on
top of the instrument panel.
● When the Intelligent Key is placed on
top of the rear parcel shelf.
● When the Intelligent Key is placed in-
side the glove box or a storage bin.
● When the Intelligent Key is placed in-
side the door pockets.
● When the Intelligent Key is placed on or
under the spare tire area.
● When the Intelligent Key is placed in-
side or near metallic materials.
Pre-driving checks and adjustments 3-11
WPD0369
NOTE: ● Doors lock with the door handle request switch when the ignition switch is placed in the ON position.
● Doors lock with the door handle request switch while the ignition switch is not in the LOCK position.
● Doors do not lock by pushing the door handle request switch while any door is open. However, doors lock with the me- chanical key even if any door is open.
The interior light can be turned off without waiting by performing one of the following operations. ● Placing the ignition switch in the ON posi-
tion.
● Locking the doors with the remote controller. ● Switching the room light switch to the OFF
position.
WPD0369
All doors will be locked automatically unless one
of the following operations is performed within 60
seconds after pushing the request switch.
● Opening any door.
● Pushing the ignition switch.
The interior light timer illuminates for a period of
time when a door is unlocked and the room light
switch is in the DOOR position.
WPD0377
Unlocking doors 1. Carry the Intelligent Key. 2. Push the door handle request switch 䊊1 . 3. The hazard warning lights flash once and the
outside buzzer sounds once.
4. Push the door handle request switch 䊊1
again within 60 seconds to unlock all doors.
If a door handle is pulled while unlocking the
doors, that door may not be unlocked. Returning
the door handle to its original position will unlock
the door. If the door does not unlock after return-
ing the door handle, push the door handle re-
quest switch to unlock the door.
3-12 Pre-driving checks and adjustments
When all doors are locked and the trunk lid is closed with the Intelligent Key inside the trunk, the outside buzzer will sound and the trunk will open. HOW TO USE THE REMOTE KEYLESS ENTRY FUNCTION The remote keyless entry function can operate all door locks using the remote keyless function of the Intelligent Key. The remote keyless function can operate at a distance of 33 ft (10 m) away from the vehicle. The operating distance de- pends upon the conditions around the vehicle. The remote keyless entry function will not func- tion under the following conditions: ● When the Intelligent Key is not within the
operational range.
● When the doors or the trunk are open or not
closed securely.
● When the Intelligent Key battery is dis-
charged.
CAUTION
When locking the doors using the Intelli- gent Key, be sure not to leave the key in the vehicle.
LPD0478
Opening the trunk lid 1. Push the trunk opener request switch 䊊A for more than 1 second while carrying the Intel- ligent Key with you.
2. The trunk will unlatch. A chime will sound 4
times.
3. Raise the trunk lid to open the trunk. Lockout protection
To prevent the Intelligent Key from being acci- dentally locked in the trunk, lockout protection is equipped with the Intelligent Key.
Locking doors 1. Place the ignition switch in the LOCK posi-
WPD0359
tion.
2. Close all doors.
3. Press the
Key.
button on the Intelligent
4. The hazard warning lights flash twice and
the horn beeps once.
5. All doors will be locked.