Download PDF Manual

washer antifreeze. Follow the manufacturer(cid:146)s in- structions for the mixture ratio.


Refill the reservoir more frequently when driving conditions require an increased amount of win- dow washer fluid. Recommended fluid is Genuine NISSAN Wind- shield Washer Concentrate Cleaner & Anti- freeze or equivalent.


CAUTION


c Do not substitute engine anti-freeze coolant for window washer solution. This may result in damage to the paint. c Do not fill the window washer reservoir tank with washer fluid concentrates at full strength. Some methyl alcohol based washer fluid concentrates may permanently stain the grille if spilled while filling the window washer reser- voir tank.


c Pre-mix washer fluid concentrates with water to the manufacturer(cid:146)s recom- mended levels before pouring the fluid into the window washer reservoir tank. Do not use the window washer reservoir tank to mix the washer fluid concen- trate and water.


c Keep the battery surface clean and dry. Any corrosion should be washed off with a solu- tion of baking soda and water.


c Make certain the terminal connections are


clean and securely tightened.


c If the vehicle is not to be used for 30 days or longer, disconnect the negative (-) battery terminal cable to prevent discharge.


WARNING


c Do not expose the battery to flames or electrical sparks. Hydrogen gas gener- ated by the battery is explosive. Do not allow battery fluid to contact your skin, eyes, fabrics or painted surfaces. After touching a battery or battery cap, do not touch or rub your eyes. Thoroughly wash your hands. If the acid contacts your eyes, skin or clothing, immediately flush with water for at least 15 minutes and seek medical attention.


c Do not operate the vehicle if the fluid in the battery is low. Low battery fluid can cause a higher load on the battery which can generate heat, reduce bat- tery life, and in some cases lead to an explosion.


Maintenance and do-it-yourself 8-13


Z REVIEW COPY—2006 Maxima (max) Owners Manual—USA_English (nna) 06/23/05—tbrooks X


c When working on or near a battery, al- ways wear suitable eye protection and remove all jewelry.


c Battery posts, terminals and related ac- cessories contain lead and lead com- pounds. Wash hands after handling.


c Keep battery out of


children.


the reach of


8-14 Maintenance and do-it-yourself


WDI0224
1. Remove the battery caps with a screwdriver as shown. Use a cloth to protect the battery case.


2. Check the fluid level


LDI0302
If it is necessary to add fluid, add only distilled water to bring the level up to the bottom of the filler opening. Do not overfill.


in each cell


Z REVIEW COPY—2006 Maxima (max) Owners Manual—USA_English (nna) 06/23/05—tbrooks X


DRIVE BELTS


Vehicles operated in high temperatures or under severe conditions require frequent checks of the battery fluid level. JUMP STARTING If jump starting is necessary, see (cid:147)Jump starting(cid:148) in the (cid:147)In case of emergency(cid:148) section of this manual. If the engine does not start by jump starting, the battery may have to be replaced. Contact a NISSAN dealer.


WDI0226


2. Have the belts checked regularly for condi- tion and tension in accordance with the maintenance the (cid:147)NISSAN Service and Maintenance Guide(cid:148).


schedule


found


in


Power steering fluid pump


1. 2. Crankshaft 3. Generator 4.


Air conditioner


WARNING


Be sure the ignition key is in the OFF or LOCK position. The engine could rotate unexpectedly.


1. Visually inspect the belt(s) for signs of un- usual wear, cuts, fraying or looseness. If the belt is in poor condition or is loose, have it replaced or adjusted by a NISSAN dealer.


Maintenance and do-it-yourself 8-15


Z REVIEW COPY—2006 Maxima (max) Owners Manual—USA_English (nna) 06/23/05—tbrooks X


SPARK PLUGS


AIR CLEANER


WARNING


Be sure the engine and ignition switch are off and that the parking brake is engaged securely.


CAUTION


Be sure to use the correct socket to re- move the spark plugs. An incorrect socket can damage the spark plugs.


If replacement is required, see your NISSAN dealer for assistance.


WDI0005


REPLACING SPARK PLUGS Platinum-tipped spark plugs It is not necessary to replace platinum-tipped spark plugs as frequently as conventional type spark plugs because they last much longer. Fol- low the maintenance log shown in the (cid:147)NISSAN Service and Maintenance Guide(cid:148). Do not service platinum-tipped spark plugs by cleaning or re- gapping. c Always replace spark plugs with rec-


ommended or equivalent ones.


8-16 Maintenance and do-it-yourself


LDI0336
The air cleaner filter should not be cleaned and reused. Replace it according to the maintenance log shown in the (cid:147)NISSAN Service and Mainte- nance Guide.(cid:148) When replacing the filter, wipe the inside of the air cleaner filter housing and the cover with a damp cloth.


Loosen the screw.


To remove the air cleaner filter: s1
s2 Disconnect the electrical connector. s3 Unlatch the clips and remove the air cleaner


cover. Remove the air cleaner filter.


Z REVIEW COPY—2006 Maxima (max) Owners Manual—USA_English (nna) 06/23/05—tbrooks X


WARNING


c Operating the engine with the air cleaner removed can cause you or oth- ers to be burned. The air cleaner not only cleans the air, it stops the flame if the engine backfires. If it isn(cid:146)t there, and the engine backfires, you could be burned. Do not drive with the air cleaner removed, and be careful when working on the engine with the air cleaner removed.


c Never pour fuel into the throttle body or attempt to start the engine with the air cleaner removed. Doing so could result in serious injury.


IN-CABIN MICROFILTER The in-cabin microfilter restricts the entry of air- borne dust and pollen particles and reduces some objectionable outside odors. The filter is located behind the glove box. Refer to the (cid:147)NISSAN Service and Maintenance Guide(cid:148) for change intervals. To replace the filter, perform the following proce- dure:


LDI0323
1. Remove the 2 lower glove box hinge pins. Remove the glove box from the opening and let it hang by the cord.


LDI0324
2. Remove the filter cover from the intake unit by disengaging the 2 hook tabs at the bot- tom of the cover.


Maintenance and do-it-yourself 8-17


Z REVIEW COPY—2006 Maxima (max) Owners Manual—USA_English (nna) 06/23/05—tbrooks X


LDI0325


NOTE: The filter is marked (cid:147)UP(cid:148) with an arrow. The end of the filter with the arrow should face the rear of the vehicle. 3. Slide the filter into the housing.


8-18 Maintenance and do-it-yourself


LDI0157


Z REVIEW COPY—2006 Maxima (max) Owners Manual—USA_English (nna) 06/23/05—tbrooks X


NOTE: Make sure the filter sits on top of the 2
supporting tabs on the housing. 4. Replace the cover by inserting the upper tabs inside the housing slot and pushing the hook tabs until they snap on to the housing lip. Install the glove box door.


5. 6. Fill out the date information on the small replacement label and attach it to the glove box lid.


Maintenance and do-it-yourself 8-19


Z REVIEW COPY—2006 Maxima (max) Owners Manual—USA_English (nna) 06/23/05—tbrooks X


WINDSHIELD WIPER BLADES


CLEANING If your windshield is not clear after using the windshield washer or if a wiper blade chatters when running, wax or other material may be on the blade or windshield. Clean the outside of the windshield with a washer solution or a mild detergent. Your windshield is clean if beads do not form when rinsing with clear water. Clean each blade by wiping it with a cloth soaked in a washer solution or a mild detergent. Then rinse the blades with clear water. If your wind- shield is still not clear after cleaning the blades and using the wiper, replace the blades. 8-20 Maintenance and do-it-yourself


CAUTION


Worn windshield wiper blades can dam- age the windshield and impair driver vision.


REPLACING Replace the wiper blades if they are worn. s1
Lift the wiper arm away from the windshield. s2 Push the release tab, then move the wiper


blade down the wiper arm to remove.


s3 Remove the wiper blade.


4.


WDI0194
Insert the new wiper blade onto the wiper arm until it clicks into place.


CAUTION


c After wiper blade replacement, return the wiper arm to its original position; otherwise it may be damaged when the hood is opened.


c Make sure the wiper blades contact the glass; otherwise the arms may be dam- aged from wind pressure.


Z REVIEW COPY—2006 Maxima (max) Owners Manual—USA_English (nna) 06/23/05—tbrooks X


PARKING BRAKE AND BRAKE PEDAL


WDI0337
Be careful not to let anything get into the washer nozzle sA . This may cause clogging or improper windshield washer operation. If something gets into the nozzle, remove it with a needle or small pin sB .


LDI0326


WDI0229


CHECKING PARKING BRAKE From the released position, pull the parking brake lever up slowly and firmly. If the number of clicks is out of the range listed, see a NISSAN dealer. c 7 - 8 clicks under pulling force of


44 lb (196 N).


CHECKING BRAKE PEDAL With the engine running, check the distance A between the upper surface of the pedal and the metal floor. If it is out of the range shown, see a NISSAN dealer. Distance A: Under depression force of 110 lb (490 N)


Automatic


Transmission


3.55 in (90.3 mm)


or more


Manual


Transmission


3.31 in (84 mm)


or more


Maintenance and do-it-yourself 8-21


Z REVIEW COPY—2006 Maxima (max) Owners Manual—USA_English (nna) 06/23/05—tbrooks X


Self-adjusting brakes Your vehicle is equipped with self-adjusting brakes. The front and rear disc-type brakes self-adjust every time the brake pedal is applied.


WARNING


See a NISSAN dealer for a brake system check if the brake pedal height does not return to normal. Brake pad wear indicators The disc brake pads on your vehicle have audible wear indicators. When a brake pad requires re- placement, a high pitched scraping or screech- ing sound will be heard when the vehicle is in motion. The noise will be heard whether or not the brake pedal is depressed. Have the brakes checked as soon as possible if the wear indicator sound is heard. Under some driving or climate conditions, occa- sional brake squeak, squeal or other noise may be heard. Occasional brake noise during light to moderate stops is normal and does not affect the function or performance of the brake system.


8-22 Maintenance and do-it-yourself


Proper brake inspection intervals should be followed. For more information regarding brake inspections, see the appropriate mainte- nance schedule information in the (cid:147)NISSAN Ser- vice and Maintenance Guide(cid:148). BRAKE BOOSTER Check the brake booster function as follows: 1. With the engine off, press and release the brake pedal several times. When brake pedal movement (distance of travel) remains the same from one pedal application to the next, continue on to the next step.


2. While depressing the brake pedal, start the engine. The pedal height should drop a little. 3. With the brake pedal depressed, stop the engine. Keep the pedal depressed for about 30 seconds. The pedal height should not change.


4. Run the engine for one minute without de- pressing the brake pedal, then turn it off. Depress the brake pedal several times. The pedal travel distance will decrease gradually with each depression as the vacuum is re- leased from the booster.


If the brakes do not operate properly, have the brakes checked by a NISSAN dealer.


FUSES


LDI0455
Two types of fuses are used. Type A is used in the fuse boxes in the engine compartment. Type B is used in the passenger compartment fuse box. Type A fuses are provided as spare fuses. They are stored in the passenger compartment fuse box. Type A fuses can be installed in the engine com- partment and passenger compartment fuse boxes.


Z REVIEW COPY—2006 Maxima (max) Owners Manual—USA_English (nna) 06/23/05—tbrooks X


3. Remove the fuse box cover by pushing the


tab and lifting the cover up.


4. Remove the fuse with the fuse puller. The fuse puller is located in the center of the fuse block in the passenger compartment.


LDI0457
If a type A fuse is used to replace a type B fuse, the type A fuse will not be level with the fuse pocket as shown in the illustration. This will not affect the performance of the fuse. Make sure the fuse is installed in the fuse box securely. Type B fuses cannot be installed in the under- hood fuse boxes. Only use type A fuses in the underhood fuse boxes.


LDI0327


ENGINE COMPARTMENT


CAUTION


Never use a fuse of a higher or lower amperage rating than specified on the fuse box cover. This could damage the electrical system or cause a fire.


If any electrical equipment does not come on, check for an open fuse.


1. Be sure the ignition switch and the headlight


switch are OFF.


2. Open the engine hood.


Maintenance and do-it-yourself 8-23


Z REVIEW COPY—2006 Maxima (max) Owners Manual—USA_English (nna) 06/23/05—tbrooks X


5.


6.


WDI0452
If the fuse is open sA , replace it with a new fuse sB . If a new fuse also opens, have the electrical system checked and repaired by a NISSAN dealer.


Fusible links If the electrical equipment does not operate and fuses are in good condition, check the fusible links. If any of these fusible links are melted, replace with only genuine NISSAN parts.


8-24 Maintenance and do-it-yourself


PASSENGER COMPARTMENT


CAUTION


Never use a fuse of a higher or lower amperage rating than specified on the fuse box cover. This could damage the electrical system or cause a fire.


If any electrical equipment does not operate, check for an open fuse. 1. Be sure the ignition switch and the headlight


switch are OFF.


2. Pull the fuse box cover to remove. 3. Remove the fuse with the fuse puller.


LDI0328


Z REVIEW COPY—2006 Maxima (max) Owners Manual—USA_English (nna) 06/23/05—tbrooks X


WDI0452


LDI0456


4.


Type A


If the fuse is open sA , replace it with a known good fuse sB .


5. Push the fuse box cover to install. 6.


If a new fuse also opens, have the electrical system checked and repaired by a NISSAN dealer.


Type B


Maintenance and do-it-yourself 8-25


Z REVIEW COPY—2006 Maxima (max) Owners Manual—USA_English (nna) 06/23/05—tbrooks X


KEYFOB BATTERY REPLACEMENT


Replace the battery in the keyfob as follows: s1 Open the lid using a coin sA . s2 Remove the battery sB . s3


Install a new battery sC with the (cid:147)+(cid:148) facing down.


8-26 Maintenance and do-it-yourself


LDI0484
Recommended battery: CR2025 or equivalent. s4 Close the lid securely. 5. Press the


button, then the


button two or three times to check the key- fob operation.


If the battery is removed for any reason other than replacement, perform step 5. c An improperly disposed battery can hurt the environment. Always confirm local regulations for battery disposal. c The keyfob is water-resistant; how- ever, if it does get wet, immediately wipe completely dry.


c The operational range of the keyfob extends to approximately 33 ft (10 m) from the vehicle. This range may vary with conditions.


FCC Notice: Changes or modifications not expressly ap- proved by the party responsible for compli- ance could void the user(cid:146)s authority to op- erate the equipment. This device complies with Part 15 of the FCC Rules and RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, in- cluding interference that may cause undes- ired operation of the device.


Z REVIEW COPY—2006 Maxima (max) Owners Manual—USA_English (nna) 06/23/05—tbrooks X


LIGHTS


HEADLIGHTS Replacing the xenon headlight bulb


WARNING


cHIGH VOLTAGE


When xenon headlights are on, they pro- duce a high voltage. To prevent an electric shock, never attempt to modify or disas- semble. Always have your xenon head- lights replaced at a NISSAN dealer. For additional information, see (cid:147)Headlight and turn signal switch(cid:148) in the (cid:147)Instru- ments and controls(cid:148) section. Replacing the halogen headlight bulb The headlight is a semi-sealed beam type which uses a replaceable headlight (halogen) bulb. Be- cause the headlight assembly must be removed from the vehicle for bulb replacement, see your NISSAN dealer.


CAUTION


c Aiming is not necessary after replacing the bulb. When aiming adjustment is necessary, contact a NISSAN dealer.


c Do not leave the headlight assembly open without a bulb installed for a long period of time. Dust, moisture, smoke, etc. entering the headlight body may affect bulb performance. Remove the bulb from the headlight assembly just before a replacement bulb is installed. c Only touch the plastic base when han- dling the bulb. Never touch the glass envelope. Touching the glass could sig- nificantly affect bulb life and/or head- light performance.


c High pressure halogen gas is sealed inside the halogen bulb. The bulb may break if the glass envelope is scratched or the bulb is dropped.


c Use the same number and wattage as


originally installed: Low beam:


Wattage: 55
Bulb no.: 9012*


High beam:


Wattage: 55
Bulb no.: 9012*


*: Always check with the Parts Depart- ment at a NISSAN dealer for the latest parts information.


Maintenance and do-it-yourself 8-27


Z REVIEW COPY—2006 Maxima (max) Owners Manual—USA_English (nna) 06/23/05—tbrooks X


EXTERIOR AND INTERIOR LIGHTS


Item


Wattage (W)


Bulb No.*


* Always check with the Parts Department at a NISSAN dealer for the latest parts information.


Headlight assembly


High/low (Halogen) High/low (Xenon) Day time running lamp Park/Turn Cornering


Front fog light Front personal/map lights Console box illumination Glove box light (if so equipped) Vanity mirror light Step light Rear personal lamps Rear console box light High-mounted stop light Trunk light Rear combination light


Tail/Stop/Turn Backup (reversing) Sidemarker License plate light


8-28 Maintenance and do-it-yourself


55


(special)


(cid:150)


27/8
27
55
3.4
3.8
3.4
2.1
3.8
3.4


27/5
13


9012
D2S 1156


1157NA 3156K


H3
(cid:150) 194
158
(cid:150) 194
(cid:150)


W5W W5W 158


3057K


912
168
168


Z REVIEW COPY—2006 Maxima (max) Owners Manual—USA_English (nna) 06/23/05—tbrooks X


Rear personal lights Step light


1. Map light 2. 3. 4. Cornering light 5. 6. 7. 8. High-mount stoplight 9. Headlamp assembly 10. Fog light


Rear combination light License plate light Trunk light


LDI0391


Maintenance and do-it-yourself 8-29


Z REVIEW COPY—2006 Maxima (max) Owners Manual—USA_English (nna) 06/23/05—tbrooks X


WDI0263


LDI0338


LDI0339


Front personal/map lights (cid:150) Type A


Use a cloth s1 to protect the housing.


Front personal/map lights (cid:150) Type B


Use a cloth s1 to protect the housing.


Replacement procedures All other lights are either type A, B, C or D. When replacing a bulb, lamp and/or cover.


first remove the lens,


Indicates bulb removal Indicates bulb installation


8-30 Maintenance and do-it-yourself


Z REVIEW COPY—2006 Maxima (max) Owners Manual—USA_English (nna) 06/23/05—tbrooks X


Vanity mirror light


Use a cloth s1 to protect the housing.


Use a cloth s1 to protect the housing.


Step light


WDI0340


LDI0341


Rear personal light


Use a cloth s1 to protect the housing.


WDI0342


Maintenance and do-it-yourself 8-31


Z REVIEW COPY—2006 Maxima (max) Owners Manual—USA_English (nna) 06/23/05—tbrooks X


Rear console box light


Squeeze the tabs on the connector. Pull out the bulb.


LDI0397


Trunk light


WDI0343


High-mounted stop light


WDI0344


8-32 Maintenance and do-it-yourself


Z REVIEW COPY—2006 Maxima (max) Owners Manual—USA_English (nna) 06/23/05—tbrooks X


WHEELS AND TIRES


If you have a flat tire, see the (cid:147)In case of emergency(cid:148) section of this manual. TIRE PRESSURE Tire inflation pressure Check the tire pressures (including the spare) often and always prior to long dis- tance trips. The recommended tire pres- sure specifications are shown on the Tire and Loading Information label under the 9Recommended Cold Tire Inflation Pres- sure9 heading. The Tire and Loading Infor- mation label is affixed to the driver side center pillar. Tire pressures should be checked regularly because: c Most tires naturally lose air over time. c Tires can lose air suddenly when driven over potholes or other objects or if the vehicle strikes a curb while parking.


The tire pressures should be checked when the tires are cold. The tires are considered COLD after the vehicle has been parked for 3 or more hours, or driven less than 1 mile (1.6 km) at moderate speeds. If the tires are used at speeds above 100
mph (162 km/h) where it is legal to do so (on a race track for example), the cold tire inflation pressure must be increased. Re- fer to 9Checking tire pressure9 later in this section. Set the tire pressure to the normal cold tire inflation pressure when the vehicle speed or load is reduced. Incorrect tire pressure, including un- der inflation, may adversely affect tire life and vehicle handling.


WARNING


c Improperly inflated tires can fail suddenly and cause an accident. c The Gross Maximum Weight rat- ing is located on the FMVSS la- bel. The vehicle weight capacity is indicated on the Tire and Load- ing Information label (if so equipped). Do not load your ve- hicle beyond this capacity. Over- loading your vehicle may result in reduced tire life, unsafe operat- ing conditions due to premature tire failure, or unfavorable han- dling characteristics and could also lead to a serious accident. Loading beyond the specified ca- pacity may also result in failure of other vehicle components.


c Before taking a long trip, or whenever you heavily load your vehicle, use a tire pressure gauge to ensure that the tire pressures are at the specified level.


Maintenance and do-it-yourself 8-33


Z REVIEW COPY—2006 Maxima (max) Owners Manual—USA_English (nna) 06/23/05—tbrooks X


c Increase the cold tire inflation pressure as indicated in (Check- ing tire pressure( later in this sec- tion when using the tires speci- fied by NISSAN above 100 MPH (162 km/h) where it is legal to do so (on a race track for example). Failure to increase the cold tire inflation pressure may result in tire failure, loss of control and possible injury. After such use, readjust tire pressure.


c Do not drive your vehicle over 85
MPH (137 km/h) unless it is equipped with high speed rated tires. Driving faster than 85 MPH (137 km/h) may result in tire fail- ure, loss of control and possible injury.


c For additional


information re- garding tires, refer to (cid:147)Important Tire Safety Information(cid:148) (US) or (cid:147)Tire Information(cid:148) (Canada) in the Warranty Infor- mation Booklet.


Safety


Tire and loading information label (for US) (if so equipped) s1 Seating capacity: The maximum num- ber of occupants that should be seated in the vehicle.


s2 Vehicle load limit: See loading infor- mation in the (cid:147)Technical and con- sumer information(cid:148) section.


s3 Original tire size: The size of the tires originally installed on the vehicle at the factory.


Type A


LDI0392


s4 Recommended cold tire inflation pressure: Inflate the tires to this pres- sure when the tires are cold. Tires are considered COLD after the vehicle has been parked for 3 or more hours, or driven less than 1 mile (1.6 km) at moderate recom- mended cold tire inflation is set by the manufacturer to provide the best bal- ance of tire wear, vehicle handling, driveability, tire noise, etc., up to the vehicles GVWR.


speeds.


The


8-34 Maintenance and do-it-yourself


Z REVIEW COPY—2006 Maxima (max) Owners Manual—USA_English (nna) 06/23/05—tbrooks X


s5 Tire size (cid:150) refer to (cid:147)Tire labeling(cid:148) later


s6


in this section. and s7 Spare tire size or compact spare tire size (if so equipped).


LDI0434


Type B


Tire and loading information label (for US) s1 Seating capacity: The maximum num- ber of occupants that should be seated in the vehicle.


s2 Vehicle load limit: See loading infor- mation in the (cid:147)Technical and con- sumer information(cid:148) section.


s3 Recommended cold tire inflation pressure: Inflate the tires to this pres- sure when the tires are cold. Tires are considered COLD after the vehicle has been parked for 3 or more hours, or driven less than 1 mile (1.6 km) at moderate recom- mended cold tire inflation is set by the manufacturer to provide the best bal- ance of tire wear, vehicle handling, driveability, tire noise, etc., up to the vehicles GVWR.


speeds.


The


Maintenance and do-it-yourself 8-35


Z REVIEW COPY—2006 Maxima (max) Owners Manual—USA_English (nna) 06/23/05—tbrooks X


s4 Original tire size: The size of the tires originally installed on the vehicle at the factory.


s5 Spare tire size or compact spare tire


size (if so equipped).


3. Remove the gauge. 4. Read the tire pressure on the gauge stem and compare to the specifica- tion shown on the Tire and Loading Information label.


5. Add air to the tire as needed. If too much air is added, press the core of the valve stem briefly with the tip of the gauge stem to release pressure. Recheck the pressure and add or release air as needed. Install the valve stem cap.


6. 7. Check the pressure of all other tires,


including the spare.


LDI0393


Checking tire pressure 1. Remove the valve stem cap from the


tire.


2. Press the pressure gauge squarely onto the valve stem. Do not press too hard or force the valve stem side- ways, or air will escape. If the hissing of air escaping from the tire is heard while checking the pressure, reposi- tion the gauge to eliminate this leak- age.


8-36 Maintenance and do-it-yourself


Z REVIEW COPY—2006 Maxima (max) Owners Manual—USA_English (nna) 06/23/05—tbrooks X


Size


Cold Tire Inflation Pressure


Front Original Tire


Rear Original Tire


P225/55R17 95V P245/45R18 96V P225/55R17 95V P245/45R18 96V T145/80*17


230 kPa, 33 PSI 220 kPa, 32 PSI 230 kPa, 33 PSI 220 kPa, 32 PSI 420 kPa, 60 PSI


Spare Tire *: (cid:147)R(cid:148) or (cid:147)D(cid:148) depending on tire manufacturer


High Speed/ Maximum Load Cold Tire Inflation Pressure 240 kPa, 35 PSI 260 kPa, 38 PSI 240 kPa, 35 PSI 260 kPa, 38 PSI


N/A


WDI0394


TIRE LABELING Federal law requires tire manufacturers to place standardized information on the sidewall of all tires. This information iden- tifies and describes the fundamental characteristics of the tire and also pro- vides the tire identification number (TIN) for safety standard certification. The TIN can be used to identify the tire in case of a recall.


Maintenance and do-it-yourself 8-37


Z REVIEW COPY—2006 Maxima (max) Owners Manual—USA_English (nna) 06/23/05—tbrooks X


s1 Tire size (example: P215/65R15 95H) 1. P: The 9P9 indicates the tire is de-


signed for passenger vehicles.


2. Three-digit number: This number gives the width in millimeters of the tire from sidewall edge to sidewall edge.


3. Two-digit number: This number, known as the aspect ratio, gives the tire(cid:146)s ratio of height to width. 4. R: The 9R9 stands for radial.


8-38 Maintenance and do-it-yourself


WDI0395
5. Two-digit number: This number is the


wheel or rim diameter in inches.


6. Two- or


three-digit number: This number is the tire(cid:146)s load index. It is a measurement of how much weight each tire can support. You may not find this information on all tires be- cause it is not required by law.


7. Tire speed rating. You should not drive the vehicle faster than the tire speed rating.


Z REVIEW COPY—2006 Maxima (max) Owners Manual—USA_English (nna) 06/23/05—tbrooks X


s2 TIN (Tire Identification Number) for a new tire (example: DOT XX XX XXX XXXX) 1. DOT: Abbreviation for the 9Department Of Transportation.9 The symbol can be placed above, below or to the left or right of Tire Identification Number.


2. Two-digit


code: Manufacturer(cid:146)s


identification mark


3. Two-digit code: Tire size 4. Three-digit code: Tire type code


(Optional)


s4 Maximum permissible inflation pres- sure This number is the greatest amount of air pressure that should be put in the tire. Do not exceed the maximum permissible in- flation pressure. s5 Maximum load rating This number indicates the maximum load in kilograms and pounds that can be car- ried by the tire. When replacing the tires on the vehicle, always use a tire that has the same load rating as the factory in- stalled tire. s6 Term of (cid:148)tubeless(cid:148) or (cid:148)tube type(cid:148) Indicates whether the tire requires an in- ner tube ((cid:147)tube type(cid:148)) or not ((cid:147)tubeless(cid:148)). s7 The word (cid:148)radial(cid:148) The word 9radial9 is shown if the tire has radial structure. s8 Manufacturer or brand name Manufacturer or brand name is shown.


Maintenance and do-it-yourself 8-39


WDI0396
5. Three-digit code: Date of Manufacture 6. Four numbers represent the week and year the tire was built. For ex- ample, the numbers 3103 means the 31st week of 2003. If these numbers are missing, then look on the other sidewall of the tire.


s3 Tire ply composition and material The number of layers or plies of rubber- coated fabric in the tire. Tire manufactur- ers also must indicate the materials in the tire, which include steel, nylon, polyester, and others.


Z REVIEW COPY—2006 Maxima (max) Owners Manual—USA_English (nna) 06/23/05—tbrooks X


Other Tire-related Terminology In addition to the many terms that are defined throughout this section, Intended Outboard Sidewall is (1) the sidewall that contains a whitewall, bears white lettering or bears manufacturer, brand, and/or model name molding that is higher or deeper than the same molding on the other sidewall of the tire, or (2) the out- ward facing sidewall of an asymmetrical tire that has a particular side that must always face outward when mounted on a vehicle. TYPES OF TIRES


WARNING


c When changing or replacing tires, be sure all four tires are of the same type (i.e., Summer, All Season or Snow) and construction. A NISSAN dealer may be able to help you with information about tire type, size, speed rating and availability.


c Replacement tires may have a lower speed rating than the factory equipped tires, and may not match the potential maximum vehicle speed. Never exceed the maximum speed rating of the tire.


c For additional


information regarding tires, refer to (cid:147)Important Tire Safety In- formation(cid:148) (US) or (cid:147)Tire Safety Informa- tion(cid:148) (Canada) in the Warranty Informa- tion Booklet.


All season tires NISSAN specifies All Season tires on some mod- els to provide good performance all year, includ- ing snowy and icy road conditions. All Season tires are identified by ALL SEASON and/or M&S on the tire sidewall. Snow tires have better snow traction than All Season tires and may be more appropriate in some areas. Summer tires NISSAN specifies summer tires on some models to provide superior performance on dry roads. Summer tire performance is substantially re- duced in snow and ice. Summer tires do not have the tire traction rating (cid:147)M&S(cid:148) on the tire sidewall.


If you do not,


If you plan to operate your vehicle in snowy or icy conditions, NISSAN recommends the use of SNOW tires or ALL SEASON tires on all four wheels. Snow tires If snow tires are needed, it is necessary to select tires equivalent in size and load rating to the original equipment tires. it can adversely affect the safety and handling of your vehicle. Generally, snow tires have lower speed ratings than factory equipped tires and may not match the potential maximum vehicle speed. Never ex- ceed the maximum speed rating of the tire. If you install snow tires, they must be the same size, brand, construction and tread pattern on all four wheels. For additional traction on icy roads, studded tires may be used. However, some U.S. states and Canadian provinces prohibit their use. Check local, state and provincial laws before installing studded tires. Skid and traction capabilities of studded snow tires on wet or dry surfaces may be poorer than that of non-studded snow tires.


8-40 Maintenance and do-it-yourself


Z REVIEW COPY—2006 Maxima (max) Owners Manual—USA_English (nna) 06/23/05—tbrooks X


or underbody. If possible, avoid fully loading your vehicle when using tire chains. In addition, drive at a reduced speed. Otherwise, your vehicle may be damaged and/or vehicle handling and perfor- mance may be adversely affected. Tire chains must be installed only on the front wheels and not on the rear wheels. Never install tire chains on a TEMPORARY USE ONLY spare tire. Do not use tire chains on dry roads. Driving with chains in such conditions can cause damage to the various mechanisms of the vehicle due to some overstress.


TIRE CHAINS


CAUTION


Tire chains/cables cannot be installed on P245/45R18 size tires. Installation of the tire chains/cables on P245/45R18 size tires will cause damage to the vehicle. If you plan to use tire chains/cables, you should install P225/55R17 size tires on your vehicle.


Use of tire chains may be prohibited according to location. Check the local laws before installing tire chains. When installing tire chains, make sure they are the proper size for the tires on your vehicle and are installed according to the chain manufacturer(cid:146)s suggestions. Use only SAE class (cid:147)S(cid:148) chains. Class 9S9 chains are used on vehicles with restricted tire to vehicle clearance. Vehicles that can use Class (cid:147)S(cid:148) chains are de- signed to meet the minimum clearances between the tire and the closest vehicle suspension or body component required to accommodate the use of a winter traction device (tire chains or cables). The minimum clearances are determined using the factory equipped tires. Other types may damage your vehicle. Use chain tensioners when recommended by the tire chain manufacturer to ensure a tight fit. Loose end links of the tire chain must be secured or removed to prevent the pos- sibility of whipping action damage to the fenders


WDI0258


CHANGING WHEELS AND TIRES Tire rotation NISSAN recommends rotating the tires every 7,500 miles (12,000 km). See (cid:147)Flat tire(cid:148) in the (cid:147)In case of emer- gency(cid:148) section of this manual for tire re- placing procedures. As soon as possible, tighten the wheel nuts to the specified torque with a torque wrench.


Maintenance and do-it-yourself 8-41


Z REVIEW COPY—2006 Maxima (max) Owners Manual—USA_English (nna) 06/23/05—tbrooks X


Wheel nut tightening torque:


80 ft-lb (108 N•m)


The wheel nuts must be kept tight- ened to specifications at all times. It is recommended that wheel nuts be tightened to specification at each tire rotation interval.


WARNING


c After rotating the tires, check and


adjust the tire pressure.


c Retighten the wheel nuts when the vehicle has been driven for 600 miles (1,000 km) (also in cases of a flat tire, etc.).


c Do not include the spare tire in


the tire rotation. c For additional


information re- garding tires, refer to (cid:147)Important Tire Safety Information(cid:148) (US) or (cid:147)Tire Information(cid:148) (Canada) in the Warranty Infor- mation Booklet.


Safety


c The original tires have built-in tread wear indicators. When the wear indicators are visible, the tire(s) should be replaced.


c Improper service of the spare tire may result in serious personal in- jury. If it is necessary to repair the spare tire, contact a NISSAN dealer.


c For additional


information re- garding tires, refer to (cid:147)Important Tire Safety Information(cid:148) (US) or (cid:147)Tire Information(cid:148) (Canada) in the Warranty Infor- mation Booklet.


Safety


Replacing wheels and tires When replacing a tire, use the same size, tread design, speed rating and load carrying capacity as originally equipped. Recommended types and sizes are shown in (cid:147)Wheels and tires(cid:148) in the (cid:147)Technical and consumer information(cid:148) section of this manual.


WDI0259


1. Wear indicator 2. Location mark Tire wear and damage


WARNING


c Tires should be periodically in- spected for wear, cracking, bulg- ing or objects caught in the tread. If excessive wear, cracks, bulging or deep cuts are found, the tire(s) should be replaced.


8-42 Maintenance and do-it-yourself


Z REVIEW COPY—2006 Maxima (max) Owners Manual—USA_English (nna) 06/23/05—tbrooks X


WARNING


c The use of tires other than those recom- mended or the mixed use of tires of different brands, construction (bias, bias-belted or radial), or tread patterns can adversely affect the ride, braking, handling, ground clearance, body-to- tire clearance, tire chain clearance, speedometer calibration, headlight aim and bumper height. Some of these ef- fects may lead to accidents and could result in serious personal injury.


c If the wheels are changed for any rea- son, always replace with wheels which have the same off-set dimension. Wheels of a different off-set could cause premature tire wear, degrade ve- hicle handling characteristics and/or interference brake discs/drums. Such interference can lead to decreased braking efficiency and/or early brake pad/shoe wear. Re- fer to (cid:147)Wheels and tires(cid:148) in the (cid:147)Techni- cal and consumer information(cid:148) section of for wheel off-set dimensions.


this manual


with


the


c Do not install a deformed wheel or tire even if it has been repaired. Such wheels or tires could have structural damage and could fail without warning. is not


retread tires


c The use of recommended. c For additional


information regarding tires, refer to (cid:147)Important Tire Safety In- formation(cid:148) (US) or (cid:147)Tire Safety Informa- tion(cid:148) (Canada) in the Warranty Informa- tion Booklet.


Wheel balance Unbalanced wheels may affect vehicle handling and tire life. Even with regular use, wheels can get out of balance. Therefore, they should be bal- anced as required. Wheel balance service should be per- formed with the wheels off the vehicle. Spin balancing the wheels on the vehicle could lead to mechanical damage. c For additional information regarding tires, refer to (cid:147)Important Tire Safety Information(cid:148) (US) or (cid:147)Tire Safety Infor- mation(cid:148) (Canada) in the Warranty In- formation Booklet .


Care of wheels c Wash the wheels when washing the vehicle


to maintain their appearance.


c Clean the inner side of the wheels when the is changed or the underside of the


wheel vehicle is washed.


c Do not use abrasive cleaners when washing


the wheels.


c Inspect wheel rims regularly for dents or corrosion. Such damage may cause loss of pressure or poor seal at the tire bead.


c NISSAN recommends waxing the road wheels to protect against road salt in areas where it is used during winter.


Maintenance and do-it-yourself 8-43


Z REVIEW COPY—2006 Maxima (max) Owners Manual—USA_English (nna) 06/23/05—tbrooks X


CAUTION


c Do not use tire chains on a TEMPO- RARY USE ONLY spare tire. Tire chains will not fit properly and may cause dam- age to the vehicle.


c Because the TEMPORARY USE ONLY spare tire is smaller than the original tire, ground clearance is reduced. To avoid damage to the vehicle, do not drive over obstacles. Also, do not drive the vehicle through an automatic car wash since it may get caught.


c When driving on roads covered with snow or ice, the TEMPORARY USE ONLY spare tire should be used on the rear wheels and the original tire used on the front wheels (drive wheels). Use tire chains only on the front (original) tires.


c Tire tread of the TEMPORARY USE ONLY spare tire will wear at a faster rate than the standard tire. Replace the spare tire as soon as the tread wear indicators appear.


c Do not use the spare tire on other


vehicles.


c Do not use more than one spare tire at


the same time.


c Do not tow a trailer when the TEMPO- RARY USE ONLY spare tire is installed.


Spare tire (TEMPORARY USE ONLY spare tire) (if so equipped) Observe the following precautions if the TEM- PORARY USE ONLY spare tire must be used. Otherwise, your vehicle could be damaged or involved in an accident:


WARNING


c The spare tire should be used for emer- gency use only. It should be replaced with the standard tire at the first oppor- tunity to avoid possible tire or differen- tial damage.


c Drive carefully while the TEMPORARY USE ONLY spare tire is installed. Avoid sharp turns and abrupt braking while driving.


c Periodically check spare tire inflation pressure. Always keep the pressure of the TEMPORARY USE ONLY spare tire at 60 psi (420 kPa, 4.2 bar).


c With the TEMPORARY USE ONLY spare tire installed do not drive the vehicle at speeds faster than 50 MPH (80 km/h).


8-44 Maintenance and do-it-yourself


Z REVIEW COPY—2006 Maxima (max) Owners Manual—USA_English (nna) 06/23/05—tbrooks X


9 Technical and consumer information


Capacities and recommended fuel/lubricants . . . . . . . . . 9-2
Fuel recommendation . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-3
Engine oil and oil filter recommendation . . . . . . . . . . . 9-5
Recommended SAE viscosity number . . . . . . . . . . . . 9-6
Air conditioner system refrigerant and oil recommendations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-6
Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-7
Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-7
Wheels and tires . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-8
Dimensions and weights . . . . . . . . . . . . . . . . . . . . . . . . 9-8


When traveling or registering your vehicle in another country . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-9
Vehicle identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-9
Vehicle identification number (VIN) plate . . . . . . . . . . 9-9
Vehicle identification number (chassis number) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-9
Engine serial number. . . . . . . . . . . . . . . . . . . . . . . . . . . 9-10
F.M.V.S.S./C.M.V.S.S. certification label . . . . . . . . . . 9-10
Emission control information label . . . . . . . . . . . . . . . 9-10


Tire placard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-11
Air conditioner specification label. . . . . . . . . . . . . . . . 9-11
Installing front license plate . . . . . . . . . . . . . . . . . . . . . . . . 9-12
Vehicle loading information . . . . . . . . . . . . . . . . . . . . . . . . 9-12
Terms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9-12
Vehicle load capacity . . . . . . . . . . . . . . . . . . . . . . . . . . 9-13
Loading tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-14
Towing a trailer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-15
Maximum load limits . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-15
Towing load/specification. . . . . . . . . . . . . . . . . . . . . . . 9-16
Towing safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-16
Flat towing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-19
Uniform tire quality grading . . . . . . . . . . . . . . . . . . . . . . . . 9-20
Emission control system warranty . . . . . . . . . . . . . . . . . . 9-21
Reporting safety defects (US only) . . . . . . . . . . . . . . . . . 9-21
Readiness for inspection/maintenance (I/M) test . . . . . 9-22
Event data recorders. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-23
Owner(cid:146)s Manual/Service Manual order information . . . 9-23
In the event of a collision . . . . . . . . . . . . . . . . . . . . . . . 9-23


Z REVIEW COPY—2006 Maxima (max) Owners Manual—USA_English (nna) 06/23/05—tbrooks X


CAPACITIES AND RECOMMENDED FUEL/LUBRICANTS


The following are approximate capacities. The actual refill capacities may be a little different. When refilling, follow the procedure described in the (cid:147)Maintenance and do-it-yourself(cid:148) section to determine the proper refill capacity.


Capacity (Approximate) US measure 20 gal


Imp measure 16-5/8 gal


Fuel Engine oil *7


Drain and Refill


With oil filter change


4-1/2 qt


Without oil filter change


4-1/4 qt


3-3/4 qt


3-1/2 qt


Cooling system


With reservoir


2-1/4 gal


1-7/8 gal


Manual transmission gear oil


2-3/8 qt


2 qt


Liter 75.6


4.2


4.0


8.5


2.2


Automatic transmission fluid Power steering fluid (PSF) Brake and clutch fluid Multi-purpose grease Air conditioning system refrigerant Air conditioning system oil Windshield washer fluid


Refill to the proper level according to the instructions in the (cid:147)Maintenance and do-it-yourself(cid:148) section.


(cid:151) (cid:151) (cid:151) (cid:151)


(cid:151) (cid:151) (cid:151) (cid:151)


(cid:151) (cid:151) (cid:151) (cid:151)


Recommended Fluids and Lubricants


Unleaded gasoline with an octane rating of at least 87 AKI (RON 91)*1


(cid:149) API Certification Mark *2 *3
(cid:149)API grade SL, Energy Conserving *2 *3
(cid:149) ILSAC grade GF-III*2 *3


50% Genuine NISSAN Long Life Antifreeze/Coolant or equivalent 50% Demineralized or distilled water Genuine NISSAN Manual Transmission Fluid (MTF) HQ Multi 75W-85 or API GL-4, Viscosity SAE 75W-85
Genuine NISSAN Matic K ATF *4
Genuine NISSAN PSF or equivalent.*8
Genuine NISSAN Super Heavy Duty Brake Fluid*5 or equivalent DOT 3
NLGI No. 2 (Lithium Soap base) HFC-134a (R-134a)*6
NISSAN A/C System Oil Type S (DH-PS) or equivalent*6
Genuine NISSAN Windshield Washer Concentrate Cleaner & Antifreeze fluid or equivalent


*1: For further details, see (cid:147)Fuel recommendation.(cid:148) *2: For further details, see (cid:147)Engine oil and oil filter recommendations.(cid:148) *3: For further details, see (cid:147)Recommended SAE viscosity number.(cid:148) *4: Using automatic transmission fluid other than Genuine NISSAN Matic K ATF will cause deterioration in driveability and automatic transmission durability, and may damage the auto- matic transmission, which is not covered by the NISSAN new vehicle limited warranty. *5: Available in mainland USA through your NISSAN dealer. *6: For further details, see (cid:147)Air conditioner specification label.(cid:148) *7: For further details, see (cid:147)Changing engine oil.(cid:148) *8: For Canada, NISSAN Automatic Transmission Fluid (ATF), DEXRON(cid:153) III/MERCON(cid:153), or equivalent ATF may also be used.


9-2 Technical and consumer information


Z REVIEW COPY—2006 Maxima (max) Owners Manual—USA_English (nna) 06/23/05—tbrooks X


FUEL RECOMMENDATION Use unleaded regular gasoline with an octane rating of at least 87 AKI (Anti-Knock Index) num- ber (Research octane number 91).


For improved vehicle performance, NISSAN rec- ommends the use of unleaded premium gasoline with an octane rating of at least 91 AKI number (Research octane number 96).


CAUTION


c Using a fuel other than that specified could adversely affect the emission control system, and may also affect the warranty coverage.


c Under no circumstances should a leaded gasoline be used, because this will damage the three-way catalyst.


Gasoline specifications NISSAN recommends using gasoline that meets the World-Wide Fuel Charter specifications where it is available. Many of the automobile manufacturers developed this specification to improve emission system and vehicle perfor- mance. Ask your service station manager if the gasoline meets the World-Wide Fuel Charter specifications.


Reformulated gasoline Some fuel suppliers are now producing reformu- lated gasolines. These gasolines are specially designed to reduce vehicle emissions. NISSAN supports efforts towards cleaner air and sug- gests that you use reformulated gasoline when available. Gasoline containing oxygenates Some fuel suppliers sell gasoline containing oxy- genates such as ethanol, MTBE and methanol with or without advertising their presence. NISSAN does not recommend the use of fuels of which the oxygenate content and the fuel com- patibility for your NISSAN cannot be readily de- termined. If in doubt, ask your service station manager.


If you use oxygenate-blend gasoline, please take the following precautions as the usage of such fuels may cause vehicle performance problems and/or fuel system damage. c The fuel should be unleaded and have an octane rating no lower than that recommended for unleaded gasoline. c If an oxygenate-blend other than metha- nol blend is used, it should contain no more than 10% oxygenate. (MTBE may, however, be added up to 15%.)


c If a methanol blend is used, it should contain no more than 5% methanol (methyl alcohol, wood alcohol). It should also contain a suitable amount of appropriate cosolvents and corro- sion inhibitors. If not properly formu- lated with appropriate cosolvents and corrosion inhibitors, such methanol blends may cause fuel system damage and/or vehicle performance problems. At this time, sufficient data is not avail- able to ensure that all methanol blends are suitable for use in NISSAN ve- hicles.


oxygenate-blend


If any driveability problems such as engine stall- ing and difficult hot-starting are experienced after using immediately change to a non-oxygenate fuel or a fuel with a low blend of MTBE. Take care not to spill gasoline during refu- eling. Gasoline containing oxygenates can cause paint damage.


fuels,


Technical and consumer information 9-3


Z REVIEW COPY—2006 Maxima (max) Owners Manual—USA_English (nna) 06/23/05—tbrooks X


Aftermarket fuel additives NISSAN does not recommend the use of any aftermarket fuel additives (for example, fuel injec- tor cleaner, octane booster, intake valve deposit removers, etc.) which are sold commercially. Many of these additives intended for gum, varnish or deposit removal may contain active solvents or similar ingredients that can be harmful to the fuel system and engine. Octane rating tips Using unleaded gasoline with an octane rating lower than recommended can cause persistent, heavy (cid:147)spark knock.(cid:148) ((cid:147)Spark knock(cid:148) is a metallic rapping noise.) If se- vere, this can lead to engine damage. If you detect a persistent heavy spark knock even when using gasoline of the stated octane rating, or if you hear steady spark knock while holding a steady speed on level roads, have a NISSAN dealer correct the condition. Failure to correct the condition is misuse of the vehicle, for which NISSAN is not responsible.


ignition timing may result


Incorrect in spark knock, after-run and/or overheating, which may cause excessive fuel consumption or engine


9-4 Technical and consumer information


damage. If any of the above symptoms are en- countered, have your vehicle checked at a NISSAN dealer. However, now and then you may notice light spark knock for a short time while accelerating or driving up hills. This is not a cause for concern, because you get the greatest fuel benefit when there is light spark knock for a short time under heavy engine load.


CAUTION


c Your vehicle is not designed to run on E-85 fuel. Using E-85 fuel in a vehicle not specifically designed for E-85 fuel can damage fuel system components and is not covered by the NISSAN new vehicle limited warranty.


c E-85 is a mixture of approximately 85% 15% unleaded


ethanol


and


fuel gasoline.


c U.S. government


regulations require ethanol dispensing pumps to be identi- fied by a small, square, orange and black label with the common abbrevia- tion or the appropriate percentage for that region.


Z REVIEW COPY—2006 Maxima (max) Owners Manual—USA_English (nna) 06/23/05—tbrooks X


ENGINE OIL AND OIL FILTER RECOMMENDATION Selecting the correct oil It is essential to choose engine oil with the cor- rect quality and viscosity to ensure satisfactory engine life and performance. NISSAN recom- mends the use of a low friction oil (energy con- serving oil) in order to improve fuel economy and conserve energy. Oils which do not have the specified quality label should not be used as they could cause engine damage.


Only those engine oils with the American Petro- leum Institute (API) CERTIFICATION MARK on


WTI0082
the front of the container should be used. This type of oil supersedes the existing API SG, SH, or SJ and Energy Conserving II categories.


If you cannot find engine oil with the API CERTI- FICATION MARK, use API grade SL Energy Conserving oil. An oil with a single designation SL, or in combination with other categories (for example, SL/CF) may also be used if one with the API CERTIFICATION MARK cannot be found. An ILSAC grade GF-III oil can also be used.


NISSAN recommends mineral based oils. These oils must, however, meet the API quality and SAE viscosity ratings specified for your vehicle.


Oil additives NISSAN does not recommend the use of oil additives. The use of an oil additive is not neces- sary when the proper oil type is used and main- tenance intervals are followed.


Oil which may contain foreign matter or has been previously used should not be used. Oil viscosity The engine oil viscosity or thickness changes with temperature. Because of this, it is important to select the engine oil viscosity based on the temperatures at which the vehicle will be oper- ated before the next oil change. The chart (cid:147)Rec- ommended SAE viscosity number(cid:148) shows the recommended oil viscosities for the expected ambient temperatures. Choosing an oil viscosity other than that recommended could cause seri- ous engine damage. Selecting the correct oil filter Your new NISSAN vehicle is equipped with a high-quality genuine NISSAN oil filter. When re- placing, use a genuine NISSAN oil filter or its equivalent for the reason described in (cid:147)Change intervals(cid:148).


Technical and consumer information 9-5


Z REVIEW COPY—2006 Maxima (max) Owners Manual—USA_English (nna) 06/23/05—tbrooks X


Change intervals The oil and oil filter change intervals for your engine are based on the use of the specified quality oils and filters. Using engine oil and filters that are not of the specified quality, or exceeding recommended oil and filter change intervals could reduce engine life. Damage to the engine caused by improper maintenance or use of incor- rect oil and filter quality and/or viscosity is not covered by the NISSAN new vehicle warranty. Your engine was filled with a high-quality engine oil when it was built. You do not have to change the oil before the first recommended change interval. Oil and filter change intervals depend upon how you use your vehicle. Operation under the following conditions may require more frequent oil and filter changes: c repeated short distance driving at cold out-


side temperatures


c driving in dusty conditions c extensive idling c towing a trailer c stop and go commuting


9-6 Technical and consumer information


ATI1028


RECOMMENDED SAE VISCOSITY NUMBER c SAE 5W-30 viscosity oil is preferred for all temperatures. SAE 10W-30 or SAE 10W-40 viscosity oils may be used if the ambient temperature is above 0(cid:176)F (-18(cid:176)C).


AIR CONDITIONER SYSTEM REFRIGERANT AND OIL RECOMMENDATIONS The air conditioner system in your NISSAN vehicle must be charged with the refriger- ant HFC-134a (R-134a) and the oil, NISSAN A/C system oil DH-PS or the exact equiva- lents.


CAUTION


The use of any other refrigerant or oil will cause severe damage to the air condition- ing system and will require the replace- ment of all air conditioner system components.


The refrigerant HFC-134a (R-134a) in your NISSAN vehicle does not harm the earth(cid:146)s ozone layer. Although this refrigerant does not affect the earth(cid:146)s atmosphere, certain government regula- tions require the recovery and recycling of any refrigerant during automotive air conditioner sys- tem service. A NISSAN dealer has the trained technicians and equipment needed to recover and recycle your air conditioner system refriger- ant. Contact a NISSAN dealer when servicing your air conditioner system.


Z REVIEW COPY—2006 Maxima (max) Owners Manual—USA_English (nna) 06/23/05—tbrooks X


SPECIFICATIONS


ENGINE


Model


Type Cylinder arrangement Bore x Stroke Displacement Firing order


Idle speed


M/T A/T (in (cid:147)N(cid:148) position) Ignition timing (degree B.T.D.C. at idle speed) CO % at idle


Spark plug


Spark plug gap (Nominal)


VQ35DE


Gasoline, 4-cycle, DOHC 6-cylinder, V-block, Slanted at 60(cid:176)


in (mm) 3.760 x 3.205 (95.5 x 81.4)


cu in (cm3) 213.45 (3,498) 1(cid:150)2(cid:150)3(cid:150)4(cid:150)5(cid:150)6


See the (cid:147)Emission Control Information label(cid:148) on the under- side of the hood.


Standard PLFR5A-11


Hot PLFR4A-11
Cold PLFR6A-11


in (mm) 0.043 (1.1)


Camshaft operation The spark ignition system of this vehicle meets all requirements of the Canadian Interference-Causing Equipment Regulations.


Timing chain


Technical and consumer information 9-7


Z REVIEW COPY—2006 Maxima (max) Owners Manual—USA_English (nna) 06/23/05—tbrooks X


WHEELS AND TIRES


DIMENSIONS AND WEIGHTS


Wheels


Tires


Spare tire


Speed rating


17 x 7JJ 18 x 7.5JJ


P225/55R17 95V P245/45R18 96V


Temporary Full size


T145/80*17
17(cid:148) or 18(cid:148)


17(cid:148) 18(cid:148)


*: (cid:147)R(cid:148) or (cid:147)D(cid:148) depending on tire manufacturer


Overall length Overall width Overall height Front tread


17 inch tire 18 inch tire


Rear tread


17 inch tire 18 inch tire


Wheelbase


Gross vehicle weight rating Gross axle weight rating


Front Rear


in (mm) 193.5 (4,915) in (mm) 71.7 (1,821) 58.3 (1,480) in (mm)


in (mm) in (mm)


61.4 (1,560) 61.0 (1,549)


61.6 (1,565) in (mm) in (mm) 61.2 (1,554) in (mm) 111.2 (2,824) lb (kg) See the (cid:147)F.M.V.S.S.


certification label(cid:148) on the center pillar between the driver(cid:146)s side front and rear doors.


lb (kg) lb (kg)


9-8 Technical and consumer information


Z REVIEW COPY—2006 Maxima (max) Owners Manual—USA_English (nna) 06/23/05—tbrooks X


WHEN TRAVELING OR REGISTERING YOUR VEHICLE IN ANOTHER COUNTRY When planning to drive your NISSAN ve- hicle in another country, you should first find out if the fuel available is suitable for your vehi- cle(cid:146)s engine. Using fuel with an octane rating that is too low may cause engine damage. All gasoline vehicles must be operated with unleaded gasoline. There- fore, avoid taking your vehicle to areas where appropriate fuel is not available. When transferring the registration of your vehicle to another country, state, province or district, it may be necessary to modify the vehicle to meet local laws and regulations. The laws and regulations for motor vehicle emis- sion control and safety standards vary according to the country, state, province or district; there- fore, vehicle specifications may differ. When any vehicle is to be taken into an- other country, state, province or district and registered, its modifications, transpor- tation, and registration are the responsibil- ity of the user. NISSAN is not responsible for any inconvenience that may result.


VEHICLE IDENTIFICATION


LTI0069
VEHICLE IDENTIFICATION NUMBER (VIN) PLATE The vehicle identification number (VIN) plate is attached as shown. This number is the identifica- tion for your vehicle and is used in the vehicle registration.


LTI0070
VEHICLE IDENTIFICATION NUMBER (chassis number) The vehicle identification number is located as shown.


Technical and consumer information 9-9


Z REVIEW COPY—2006 Maxima (max) Owners Manual—USA_English (nna) 06/23/05—tbrooks X


WTI0049


LTI0071


LTI0072


ENGINE SERIAL NUMBER The number is stamped on the engine as shown.


F.M.V.S.S./C.M.V.S.S. CERTIFICATION LABEL The Federal/Canadian Motor Vehicle Safety Standard (F.M.V.S.S./C.M.V.S.S.) certification la- bel is affixed as shown. This label contains valu- able vehicle information, such as: Gross Vehicle Weight Ratings (GVWR), Gross Axle Weight Rating (GAWR), month and year of manufacture, Vehicle Identification Number (VIN), etc. Review it carefully.


EMISSION CONTROL INFORMATION LABEL The emission control tached as shown.


information label


is at-


9-10 Technical and consumer information


Z REVIEW COPY—2006 Maxima (max) Owners Manual—USA_English (nna) 06/23/05—tbrooks X


Type A


Type B


LTI0073


LTI0120


TIRE PLACARD The cold tire pressure is shown on the tire plac- ard. The tire placard is located as shown.


WTI0153
AIR CONDITIONER SPECIFICATION LABEL The air conditioner specification label is affixed as shown.


Technical and consumer information 9-11


Z REVIEW COPY—2006 Maxima (max) Owners Manual—USA_English (nna) 06/23/05—tbrooks X


INSTALLING FRONT LICENSE PLATE


VEHICLE LOADING INFORMATION


Use the following steps to mount the front license plate: Before mounting the license plate, confirm that the following parts are enclosed in the plastic bag: c License plate bracket c License plate bracket screws x 2
c License plate screws x 2
c Screw grommets x 2
1. Make a shallow hole in the bumper fascia at the location marks (small dimples) using a 0.39 in (10 mm) drill. To avoid damaging the area behind the fascia, apply only light pres- sure to the drill. Insert the grommets into the holes in the bumper fascia. Insert a small flat-bladed screwdriver into the grommet hole to turn the threaded part of the grommet 90(cid:176).


2.


3.


4. Mount the license plate bracket using the


two longer screws.


5. Use the two shorter hex head screws to mount the license plate to the license plate bracket.


9-12 Technical and consumer information


Loading...
x