2009 Nissan Frontier Owners Manual

the driver(cid:146)s door, the system may not arm. Furthermore, if the key is turned beyond the vertical position toward the unlock position to remove the key, the system may be disarmed when the key is removed. If the indicator light fails to glow for 30 seconds, unlock the door once and lock it again.

c Even when the driver and/or passen- gers are in the vehicle, the system will arm with all doors closed and locked with the ignition switch placed in the OFF position.

Vehicle security system activation The vehicle security system will give the following alarm: c The headlights blink and the horn sounds

intermittently.

c The alarm automatically turns off after ap- proximately 50 seconds. However, the alarm reactivates if the vehicle is tampered with again. The alarm can be shut off by unlocking the driver(cid:146)s door with the key or by pressing the

button on the keyfob.

The alarm is activated by:

2-24 Instruments and controls

c opening a door without using the key or keyfob (even if the door is unlocked by using the inside lock knob or the power door lock switch).

How to stop an activated alarm The alarm stops only by unlocking the driver(cid:146)s door with the key or by pressing the button on the keyfob. NISSAN VEHICLE IMMOBILIZER SYSTEM (if so equipped) The NISSAN Vehicle Immobilizer System will not allow the engine to start without the use of a registered key.

If the engine fails to start using a registered key (for example, when interference is caused by another registered key, an automated toll road device or automatic payment device on the key ring), restart the engine using the following pro- cedures:

1. Leave the ignition switch in the ON position

for approximately 5 seconds.

2. Turn the ignition switch to the OFF or LOCK position, and wait approximately 10 sec- onds.

3. Repeat steps 1 and 2.

4. Restart the engine while holding the device (which may have caused the interference) separate from the registered key.

If the no start condition re-occurs, NISSAN rec- ommends placing the registered key on a sepa- rate key ring to avoid interference from other devices. Statement related to Section 15 of FCC Rules for NISSAN Vehicle Immobilizer Sys- tem (CONT ASSY (cid:151) IMMOBILIZER, ANT ASSY (cid:151) IMMOBILIZER) This device complies with part 15 of the FCC Rules and RSS-210 of Industry Canada. Operation is subject to the follow- ing two conditions; (1) This device may not cause harmful in- terference, and (2) this device must accept any interference received, including inter- ference that may cause undesired opera- tion of the device. CHANGES OR MODIFICATIONS NOT EX- PRESSLY APPROVED BY THE PARTY RE- SPONSIBLE FOR COMPLIANCE COULD VOID THE USER(cid:146)S AUTHORITY TO OPER- ATE THE EQUIPMENT.

Z REVIEW COPY—2009 08+ Truck/Frontier (fro) Owners Manual—USA_English (nna) 05/27/08—debbie X

WINDSHIELD WIPER AND WASHER SWITCH

LIC0474

WIC0854

Security indicator light The security indicator light blinks whenever the ignition switch is placed in the LOCK, OFF or ACC position. This function indicates the NISSAN Ve- hicle Immobilizer System is operational. If the NISSAN Vehicle Immobilizer System is mal- functioning, the light will remain on while the ignition switch is placed in the ON position. If the light still remains on and/or the en- gine will not start, see a NISSAN dealer for NISSAN Vehicle Immobilizer System ser- vice as soon as possible. Please bring all registered keys that you have when visiting your NISSAN dealer for service.

SWITCH OPERATION The windshield wiper and washer operates when the ignition switch is placed in the ON position.

Push the lever down to operate the wiper at the following speed: s1

Intermittent (INT) (cid:151) intermittent operation can be adjusted by turning the knob toward sA (Slower) or sB (Faster). s2
Low (LO) (cid:151) continuous low speed operation s3 High (HI) (cid:151) continuous high speed opera-

tion

Push the lever up s4 to have one sweep opera- tion (MIST) of the wiper. Pull the lever toward you s5
to operate the washer. The wiper will also operate several times.

WARNING

In freezing temperatures the washer solu- tion may freeze on the windshield and obscure your vision which may lead to an accident. Warm the windshield with the defroster before you wash the windshield.

CAUTION

c Do not operate the washer continu-

ously for more than 30 seconds.

c Do not operate the washer if the reser-

voir tank is empty.

c Do not fill the window washer reservoir tank with washer fluid concentrates at full strength. Some methyl alcohol based washer fluid concentrates may permanently stain the grille if spilled while filling the window washer reser- voir tank.

Instruments and controls 2-25

Z REVIEW COPY—2009 08+ Truck/Frontier (fro) Owners Manual—USA_English (nna) 05/27/08—debbie X

REAR WINDOW AND OUTSIDE MIRROR DEFROSTER SWITCH (if so equipped)

c Pre-mix washer fluid concentrates with water to the manufacturer(cid:146)s recom- mended levels before pouring the fluid into the window washer reservoir tank. Do not use the window washer reservoir tank to mix the washer fluid concen- trate and water.

LIC0783

LIC1419

Type A

To defrost the rear window glass and outside mirrors (if so equipped), start the engine and push the rear window defroster switch on. The rear window defroster light on the switch comes on. Push the switch again to turn the defroster off.

indicator

The rear window defroster automatically turns off after approximately 15 minutes.

Type B

CAUTION

When cleaning the inner side of the rear window, be careful not to scratch or dam- age the rear window defroster.

2-26 Instruments and controls

Z REVIEW COPY—2009 08+ Truck/Frontier (fro) Owners Manual—USA_English (nna) 05/27/08—debbie X

HEADLIGHT AND TURN SIGNAL SWITCH

WIC1424

WIC1452

WIC1426

Type A

HEADLIGHT CONTROL SWITCH Lighting s1 When turning the switch to the

posi- tion, the front parking, tail, license plate and instrument panel lights come on. s2 When turning the switch to the

posi- tion, the headlights come on and all the other lights remain on.

Type B

CAUTION

Use the headlights with the engine run- ning to avoid discharging the vehicle battery.

Type C

Instruments and controls 2-27

Z REVIEW COPY—2009 08+ Truck/Frontier (fro) Owners Manual—USA_English (nna) 05/27/08—debbie X

WIC1453

Autolight system (if so equipped) The autolight system allows the headlights to be set so they turn on and off automatically. The autolight system can: c Turn on the headlights, front parking, tail, license plate and instrument panel lights au- tomatically when it is dark.

c Turn off all the lights when it is light. c Keep all the lights on for 45 seconds after you turn the key to OFF and all doors are closed.

2-28 Instruments and controls

To turn on the autolight system: 1. Turn the headlight switch to the AUTO posi-

tion s1 .

2. Turn the ignition switch to ON. 3. The autolight system automatically turns the

headlights on and off.

Initially, if the ignition switch is turned OFF and a door is opened and left open, the headlights remain ON for 5 minutes. If another door is opened during the 5 minutes, then the 5 minute timer is reset. To turn the autolight system off, turn the switch to the OFF,

position.

, or

LIC0835
Be sure you do not put anything on top of the autolight sensor s1 located in the top side of the instrument panel. The autolight sensor controls the autolight; if it is cov- ered, the autolight sensor reacts as if it is dark out and the headlights will illuminate. If this occurs while parked with the engine off and the switch in the ON position, your vehicle(cid:146)s battery could become discharged.

Z REVIEW COPY—2009 08+ Truck/Frontier (fro) Owners Manual—USA_English (nna) 05/27/08—debbie X

ning lights will remain on until the ignition switch is placed in the OFF position.

WARNING

When the daytime running light system is active, tail lights on your vehicle are not on. It is necessary at dusk to turn on your headlights. Failure to do so could cause an accident injuring yourself and others.

After the headlights automatically turn off with the position, headlight switch in the the headlights will illuminate again for 5 minutes if the headlight switch is moved to the OFF position and then turned to the position.

or

or

CAUTION

Even though the battery saver feature au- tomatically turns off the headlights after a period of time, you should turn the head- light switch to the OFF position when the engine is not running to avoid discharging the vehicle battery.

DAYTIME RUNNING LIGHT SYSTEM (Canada only) The headlights automatically illuminate at a re- duced intensity when the engine is started with the parking brake released. The daytime running lights operate with the headlight switch in the OFF position or in the position. Turn the headlight switch to the position for full illumination when driving at night.

If the parking brake is applied before the engine is started, the daytime running lights do not illumi- nate. The daytime running lights illuminate when the parking brake is released. The daytime run-

WIC1427

Headlight beam select s1 To select the high beam function, push the lever forward. The high beam lights come on and the

light illuminates.

s2 Pull the lever back to select the low beam. s3 Pulling and releasing the lever flashes the

headlight high beams on and off.

Battery saver system If the ignition switch is placed in the OFF position while the headlight switch is in the or 5 minutes.

position, the headlights will turn off after

Instruments and controls 2-29

Z REVIEW COPY—2009 08+ Truck/Frontier (fro) Owners Manual—USA_English (nna) 05/27/08—debbie X

WIC0917

WIC1428

INSTRUMENT BRIGHTNESS CONTROL The instrument brightness control operates when control the in the or AUTO position (if so equipped) (with autolights activated). Turn the control sA to adjust the brightness of the instrument panel lights when driving at night.

headlight

switch

is

TURN SIGNAL SWITCH Turn signal s1 Move the lever up or down to signal the turning direction. When the turn is com- pleted, the turn signals cancel automatically.

Lane change signal s2 To signal a lane change, move the lever up or down to the point where the indicator light begins to flash, but the lever does not latch.

position.

LIC0393
FOG LIGHT SWITCH (if so equipped) To turn the fog lights on, turn the headlight switch position, then turn the fog light to the switch to the To turn the fog lights on with the headlight switch in the AUTO position (if so equipped), the head- lights must be on, then turn the fog light switch to the To turn the fog lights off, turn the fog light switch to the OFF position. The headlights must be on and the low beams selected for the fog lights to operate. The fog lights automatically turn off when the high beam headlights are selected.

position.

2-30 Instruments and controls

Z REVIEW COPY—2009 08+ Truck/Frontier (fro) Owners Manual—USA_English (nna) 05/27/08—debbie X

HAZARD WARNING FLASHER SWITCH

HORN

The flashers will operate with the ignition switch placed in any position. Some state laws may prohibit the use of the hazard warning flasher switch while driving.

LIC0394
Push the switch on to warn other drivers when you must stop or park under emergency condi- tions. All turn signal lights flash.

WARNING

c If stopping for an emergency, be sure to

move the vehicle well off the road.

c Do not use the hazard warning flashers while moving on the highway unless unusual circumstances force you to drive so slowly that your vehicle might become a hazard to other traffic.

c Turn signals do not work when the haz-

ard warning flasher lights are on.

WIC1449

To sound the horn, push the area between the horn icons on the steering wheel.

WARNING

Do not disassemble the horn. Doing so could affect proper operation of the supplemental front air bag system. Tam- pering with the supplemental front air bag system may result in serious personal injury.

Instruments and controls 2-31

Z REVIEW COPY—2009 08+ Truck/Frontier (fro) Owners Manual—USA_English (nna) 05/27/08—debbie X

CARGO LAMP SWITCH

HEATED SEAT (if so equipped)

LIC0616
To turn on the cargo lamp, push the switch down to the ON position.

CAUTION

Be sure to turn the light switch to the OFF position when you leave the vehicle for extended periods of time, otherwise the battery will go dead.

2-32 Instruments and controls

LIC1041

The front seats are warmed by built-in heaters (if so equipped). 1. Start the engine. 2. Push the LO or HI position of the switch, as desired, depending on the temperature. The indicator light in the switch will illuminate. The heater is controlled by a thermostat, automatically turning the heater on and off. The indicator light will remain on as long as the switch is on.

3. When the seat is warmed or before you leave the vehicle, be sure to turn the switch off.

CAUTION

c Do not use the seat heater for extended periods or when no one is using the seat.

c Do not put anything on the seat which insulates heat, such as a blanket, cush- ion, seat cover, etc. Otherwise, the seat may become overheated.

c Do not place anything hard or heavy on the seat or pierce it with a pin or similar object. This may result in damage to the heater.

c Any liquid spilled on the heated seat should be removed immediately with a dry cloth.

c When cleaning the seat, never use gasoline, benzine, thinner, or any simi- lar materials.

c If any abnormalities are found or the heated seat does not operate, turn the switch off and have the system checked by your NISSAN dealer.

c The battery could run down if the seat heater is operated while the engine is not running.

Z REVIEW COPY—2009 08+ Truck/Frontier (fro) Owners Manual—USA_English (nna) 05/27/08—debbie X

VEHICLE DYNAMIC CONTROL (VDC) OFF SWITCH (if so equipped)

HILL DESCENT CONTROL SWITCH (if so equipped)

WIC0534
The vehicle should be driven with the Vehicle Dynamic Control (VDC) system on for most driv- ing conditions. If the vehicle is stuck in mud or snow, the VDC system reduces the engine output to reduce wheel spin. The engine speed will be reduced even if the accelerator is depressed to the floor. If maximum engine power is needed to free a stuck vehicle, turn the VDC system off. To turn off the VDC system, push the VDC OFF switch. The Push the VDC OFF switch again or restart the engine to turn on the system. See (cid:147)Vehicle Dy- namic Control (VDC) system(cid:148) in the (cid:147)Starting and driving(cid:148) section.

indicator will come on.

LIC0743

WARNING

c Never rely solely on the hill descent control system to control vehicle speed when driving on steep downhill grades. Always drive carefully when using the hill descent control system and decel- erate the vehicle speed by depressing the brake pedal if necessary. Be espe- cially careful when driving on frozen, muddy or extremely steep downhill roads. Failure to control vehicle speed may result in a loss of control of the vehicle and possible serious injury or death.

c The hill descent control may not control the vehicle speed on a hill under all load or road conditions. Always be prepared to depress the brake pedal to control vehicle speed. Failure to do so may re- sult in a collision or serious personal injury.

CAUTION

When the hill descent control system op- erates continuously for a long time, the temperature of the brake pads may in- crease and the hill descent control system may be temporarily disabled (the indicator light will blink). If the indicator light does not come on continuously after blinking, stop using the system.

The hill descent control system is designed to reduce driver workload when going down steep hills. The hill descent control system helps to control vehicle speed so the driver can concen- trate on steering the vehicle. To activate the hill descent control system: c the shift selector must be in forward or re-

verse gear,

c the 4WD switch must be in the 4L position and the vehicle speed must be under 15
mph (25 km/h) or

Instruments and controls 2-33

Z REVIEW COPY—2009 08+ Truck/Frontier (fro) Owners Manual—USA_English (nna) 05/27/08—debbie X

ELECTRONIC LOCKING REAR DIFFERENTIAL (E-Lock) SYSTEM SWITCH (if so equipped)

LIC0729
The Electronic Locking Rear Differential (E-Lock) system can help provide added traction if the vehicle is stuck or becoming stuck. To activate the E-Lock system: c the 4WD switch must be in the 4LO position

(4-wheel drive vehicles),

c the vehicle must be stopped or moving at 4

mph (7 km/h) or less, and

c the E-Lock system switch must be turned

ON.

When the E-Lock switch is turned ON, the indi- cator light will flash until the system engages. However, if all operation conditions listed above are not met or the system becomes disengaged, the indicator light will continue to flash.

The Anti-Lock Brake (ABS) system is disabled and the ABS light illuminates when the E-Lock system is ON. Also, the Vehicle Dynamic Control (VDC) system is disabled and the VDC light illuminates when the E-Lock system is ON.

See (cid:147)Electronic locking rear differential (E-Lock) system(cid:148) in the (cid:147)Starting and Driving(cid:148) section for further explanation and system limitations.

WARNING

c Never leave the E-Lock system ON when driving on paved or hard-surfaced roads. Turning the vehicle may result in the rear wheels slipping and result in an accident and personal injury. After us- ing the E-Lock system to free the ve- hicle, turn the system OFF.

c the 4WD switch must be in the 4H position and the vehicle speed must be under 21
mph (35 km/h), and

c the hill descent control system switch must

be ON.

The hill descent control system on indicator light will come on when the system is activated. Also, the stop/tail lights illuminate while the hill descent control system applies the brakes to control ve- hicle speed. If the accelerator or brake pedal is depressed while the hill descent control system is on, the system will stop operating temporarily. As soon as the accelerator or brake pedal is released, the hill descent control system begins to function again if the hill descent control operating condi- tions are fulfilled. The hill descent control system on indicator light blinks if the switch is on and all conditions for system activation are not met or if the system becomes disengaged for any reason. To turn off the hill descent control system, push the switch to the OFF position. For additional information, see (cid:147)Hill descent con- trol system on indicator light(cid:148) earlier in this sec- tion and (cid:147)Hill descent control system(cid:148) in the (cid:147)Starting and driving(cid:148) section of this manual.

2-34 Instruments and controls

Z REVIEW COPY—2009 08+ Truck/Frontier (fro) Owners Manual—USA_English (nna) 05/27/08—debbie X

c Use the E-Lock system only when free- ing a stuck vehicle. Try the 4LO position before using the E-Lock system. Never use the E-Lock system on a slippery road surface such as snow or ice sur- face. Using the E-Lock system when driving in these road conditions may cause unexpected movement of the ve- hicle during engine braking, accelerat- ing or turning, which may result in an accident and serious personal injury.

CAUTION

c After using the E-Lock system, turn the switch OFF to prevent possible damage to driveline components from extended use.

c Do not drive over 12 MPH (20 km/h) when the system is engaged. Doing so could result in possible damage to the driveline.

c Do not turn on the E-lock system while the tires are spinning. Doing so could damage drivetrain components.

CLUTCH INTERLOCK (clutch start) SWITCH (if so equipped)

WIC0817

WARNING

Pay special attention to your surround- ings when using the clutch interlock switch. The vehicle will move forward or backward according to the gear selected.

The clutch interlock (clutch start) switch allows for starting the engine without depressing the clutch pedal. This feature helps you restart the engine if it stops under difficult conditions. (For example, the engine stops on a steep hill and a slight movement forward or backward might be dangerous.)

To use the clutch interlock switch: 1. Set the parking brake. 2. Depress the brake pedal with your right foot. 3. Place the shift selector in the 1 position to

move forward, or R to move backward.

4. Place your left foot on the brake pedal and

release the parking brake.

5. Turn the ignition switch to the ON position. 6. Press and release the clutch interlock switch. The CANCEL light on the switch will illuminate.

7. Turn the ignition to the START position to start the engine and, at the same time, de- press the accelerator pedal with your right foot. As the vehicle begins to move, take your left foot off the brake. Once the engine has started, the clutch interlock switch CANCEL light shuts off. Do not use the interlock switch to start the engine under normal driving conditions.

Instruments and controls 2-35

Z REVIEW COPY—2009 08+ Truck/Frontier (fro) Owners Manual—USA_English (nna) 05/27/08—debbie X

POWER OUTLET

LIC1430

LIC0761

Front row

The power outlets are for powering electrical accessories such as cellular telephones.

The bottom power outlet located on instrument panel is powered directly by the vehicle(cid:146)s battery.

The top power outlet (if so equipped) located on the instrument panel and the power outlet lo- cated inside the center console are powered only when the ignition switch is in the ACC or ON position.

Open the cap to use a power outlet.

Center console

CAUTION

c The outlet and plug may be hot during

or immediately after use.

c Only certain power outlets are designed for use with a cigarette lighter unit. Do not use any other power outlet for an accessory lighter. See your NISSAN dealer for additional information.

c Do not use with accessories that ex- ceed a 12 volt, 120W (10A) power draw. Do not use double adapters or more than one electrical accessory.

2-36 Instruments and controls

c Use power outlets with the engine run- ning to avoid discharging the vehicle battery.

c Avoid using power outlets when the air conditioner, headlights or rear window defroster is on.

c Before inserting or disconnecting a plug, be sure the electrical accessory being used is turned OFF.

c Push the plug in as far as it will go. If good contact is not made, the plug may overheat or the internal temperature fuse may open.

c When not in use, be sure to close the cap. Do not allow water to contact the outlet.

Z REVIEW COPY—2009 08+ Truck/Frontier (fro) Owners Manual—USA_English (nna) 05/27/08—debbie X

STORAGE

Top center tray

STORAGE TRAYS

WARNING

WIC1429

LIC0818

WIC1431

AT model

MT model (if so equipped)

Do not place sharp objects in the trays to help prevent injury in an accident or sud- den stop.

Instruments and controls 2-37

Z REVIEW COPY—2009 08+ Truck/Frontier (fro) Owners Manual—USA_English (nna) 05/27/08—debbie X

MT model (if so equipped)

WIC1432

2-38 Instruments and controls

2nd row under-seat storage bin

(King cab model)

2nd row under-seat storage bin

(Crew cab model)

LIC0821

LIC0820

Z REVIEW COPY—2009 08+ Truck/Frontier (fro) Owners Manual—USA_English (nna) 05/27/08—debbie X

c Do not place sharp objects in the under- seat storage bins. Such objects may become dangerous projectiles and cause injury when the vehicle is moving or if the vehicle is involved in a collision.

To access the under-seat storage bins: For King cab model, lift up the jump seat. Refer to (cid:147)Jump seat(cid:148) in the (cid:147)Safety(cid:151)Seats, seat belts and supplemental restraint system(cid:148) section earlier in this manual. For Crew cab model, lift up the rear bench seat. Refer to (cid:147)Folding the rear bench seat(cid:148) in the (cid:147)Safety(cid:151)Seats, seat belts and supplemental re- straint system(cid:148) section earlier in this manual.

UNDER-SEAT STORAGE BINS

WARNING

c Properly secure all cargo with ropes or straps to help prevent it from sliding or shifting. In a sudden stop or collision, unsecured cargo could cause personal injury.

c The cargo restrained in the under-seat storage bins must not exceed the weight limits listed below or the bins may not stay secured. In a sudden stop or collision, the unsecured bins could cause personal inury. King cab model: 16 lb (7.25 kg) Crew cab model

Driver(cid:146)s side: 16 lb (7.25 kg) Passenger(cid:146)s side: 25 lb (11.33 kg)

c If the under-seat storage bins are re- moved for any reason, they should be securely stored to prevent them from causing injury to passengers or damage to the vehicle in case of sudden braking or an accident.

LIC0822

To remove the under-seat storage bins: 1. Remove the storage net. 2. Remove the tray by lifting it out of the stor-

age bin (King cab model).

3. Turn the knobs to the UNLOCK position s2 . To install the under-seat storage bins: 1. Position the under-seat storage bin so the holes line up with the holes in the floorboard. Insert the knobs and turn them to the LOCK position s1 .

2.

Instruments and controls 2-39

Z REVIEW COPY—2009 08+ Truck/Frontier (fro) Owners Manual—USA_English (nna) 05/27/08—debbie X

LIC0766

LIC0768

WIC0673

CONSOLE BOX Pull up on the lever s1 to open the console box lid s2 .

2-40 Instruments and controls

SUNGLASSES HOLDER (if so equipped) To open the sunglasses holder, push and release.

WARNING

c Keep the sunglasses holder closed

while driving to prevent an accident.

GLOVE BOX To open the top portion of the glove box, push the latch sA up and raise the lid. To open the lower portion of the glove box, pull the handle sB down and lower the lid. Use the master key to lock or unlock the glove box. The valet key cannot be used to lock or unlock the glove box.

WARNING

Keep glove box lid closed while driving to help prevent injury in an accident or a sudden stop.

Z REVIEW COPY—2009 08+ Truck/Frontier (fro) Owners Manual—USA_English (nna) 05/27/08—debbie X

CAUTION

c Do not use for anything other than

sunglasses.

c Do not leave sunglasses in the sun- glasses holder while parking in direct sunlight. The heat may damage the sunglasses.

MAP POCKETS

WIC0824

King cab model

LIC0826

Instruments and controls 2-41

Z REVIEW COPY—2009 08+ Truck/Frontier (fro) Owners Manual—USA_English (nna) 05/27/08—debbie X

Crew cab model

LIC0825

LIC0575

SEAT POCKETS (if so equipped) A pocket is located on the back of the driver(cid:146)s seat.

WIC0827

Front

CUP HOLDERS The front cup holders have adapters that can be removed to accommodate larger cups.

WARNING

The cup holder should not be used while driving so full attention may be given to vehicle operation.

2-42 Instruments and controls

Z REVIEW COPY—2009 08+ Truck/Frontier (fro) Owners Manual—USA_English (nna) 05/27/08—debbie X

CAUTION

c Avoid abrupt starting and braking when the cup holder is being used to prevent spilling the drink. If the liquid is hot, it can scald you or your passenger.

c Use only soft cups in the cup holder. Hard objects can injure you in an accident.

2nd row (rear of front console)

Bottle holder (front row)

WIC0771

LIC0784

To open the 2nd row cup holders (rear of the front console), lower the lid. To close, raise the lid. If stepped on, the cup holder is designed to snap loose from the console. To re-install, close the cup holder assembly and push it back into the console opening. To fold the 2nd row bench seat back, first close the cup holder.

CAUTION

c Do not use bottle holder for any other objects that could be thrown about in the vehicle and possibly injure people during sudden braking or an accident. c Do not use bottle holder for open liquid

containers.

Instruments and controls 2-43

Z REVIEW COPY—2009 08+ Truck/Frontier (fro) Owners Manual—USA_English (nna) 05/27/08—debbie X

Bottle holder (2nd row, Crew cab)

WIC0828

2-44 Instruments and controls

ROOF RACK (if so equipped)

WIC0857

Z REVIEW COPY—2009 08+ Truck/Frontier (fro) Owners Manual—USA_English (nna) 05/27/08—debbie X

WARNING

c Drive extra carefully when the vehicle is loaded at or near the cargo carrying capacity, especially if the significant portion of that load is carried on the roof rack.

c Heavy loading of the roof rack has the potential to affect the vehicle stability and handling during sudden or abnor- mal handling maneuvers.

c Roof

rack load should be evenly

distributed.

c Do not exceed maximum roof rack load

weight capacity.

c Properly secure all cargo with ropes or straps to help prevent it from sliding or shifting. In a sudden stop or collision, unsecured cargo could cause personal injury.

CAUTION

Use care when placing or removing items from the roof rack. If you cannot comfort- ably lift the items onto the roof rack from the ground, use a ladder or stool.

To remove: 1. Loosen the adjusting screws with the Torxdriver s1 by turning counterclockwise sA .

2. Rotate the clamps sC . 3. Remove the crossbar. 4. Reverse to install. 5. Always check the tightness of the crossbar

adjusting screws.

If you hear wind noise coming from the roof rack while driving, adjust the roof rack crossbar to the neutral position, rearward of D on the side rails.

Always evenly distribute the cargo on the tubular roof rack. The maximum total load is 125 lb (56 kg) evenly distributed. Be careful that your vehicle does not exceed the Gross Vehicle Weight Rating (GVWR) or the Gross Axle Weight Ratings (GAWR front and rear). The GVWR and GAWR are located on the F.M.V.S.S. label (located on the driver(cid:146)s side door jamb pillar). For more information regarding GVWR and GAWR, refer to (cid:147)Vehicle loading information(cid:148) in the (cid:147)Technical and consumer information(cid:148) sec- tion later in this manual.

The front crossbar can be adjusted or removed. Use the Torxdriver provided in the tool kit to loosen both crossbar adjusting screws. To adjust: 1. Loosen the adjusting screws with the Torxdriver s1 by turning counterclockwise sA .

2. When the clamp is loosened, move the crossbar so the cargo can be positioned on the crossbar sB .

3. Tighten the crossbar adjusting screws with

the Torxdriver by turning clockwise.

4. Secure the cargo with rope. 5. Always check the tightness of the crossbar

adjusting screws.

Instruments and controls 2-45

Z REVIEW COPY—2009 08+ Truck/Frontier (fro) Owners Manual—USA_English (nna) 05/27/08—debbie X

WINDOWS

POWER WINDOWS (if so equipped)

WARNING

c Make sure that all passengers have their hands, etc. inside the vehicle while it is in motion and before closing the windows. Use the window lock switch to prevent unexpected use of the power windows.

c Do not leave children unattended inside the vehicle. They could unknowingly ac- tivate switches or controls and become trapped in a window. Unattended chil- dren could become involved in serious accidents.

The power windows operate when the ignition switch is placed in the ON position, or for about 45 seconds after the ignition switch is placed in the OFF position. If the driver(cid:146)s or passenger(cid:146)s door is opened during this period of about 45
seconds, power to the windows is canceled.

2-46 Instruments and controls

Driver(cid:146)s side power window switch The driver(cid:146)s side control panel is equipped with switches to open or close the front and rear passenger windows. To open a window, push the switch and hold it down. To close a window, pull the switch and hold it up. To stop the opening or closing function at any time, simply release the switch.

LIC1329

1. Window lock button 2. 3. 4.

Power door lock switch Front passenger side window switch Right rear passenger window switch (Crew Cab models only) Left rear passenger window switch (Crew Cab models only) Driver(cid:146)s side automatic switch

5.

6.

Z REVIEW COPY—2009 08+ Truck/Frontier (fro) Owners Manual—USA_English (nna) 05/27/08—debbie X

LIC0786

LIC0787

LIC0410

Front passenger(cid:146)s power window switch The passenger(cid:146)s window switch operates only the corresponding passenger(cid:146)s window. To open the window, push the switch and hold it down s1 . To close the window, pull the switch up s2 .

Rear power window switch (Crew Cab models only) The rear power window switches open or close only the corresponding passenger window. To open the window, push the switch and hold it down s1 . To close the window, push the switch up s2 . Locking passengers(cid:146) windows When the window lock button is depressed, only the driver(cid:146)s side window can be opened or closed. Push it again to cancel the window lock function.

Automatic operation To fully open a window equipped with automatic operation, press the window switch down to the second detent and release it; it need not be held. The window automatically opens all the way. To stop the window, lift the switch up while the window is opening.

Instruments and controls 2-47

Z REVIEW COPY—2009 08+ Truck/Frontier (fro) Owners Manual—USA_English (nna) 05/27/08—debbie X

MOONROOF (if so equipped)

WIC0263
MANUAL WINDOWS (if so equipped) The side windows can be opened or closed by turning the hand crank on each door.

WIC0856

WIC0882

REAR SLIDING WINDOW (if so equipped) Squeeze the handles of the lever s1 , then slide the window open s2 .

Sliding the moonroof To fully open the moonroof, push the switch to- ward DOWN/OPEN s1 . To fully close the moonroof, push the switch toward UP/CLOSE s2 . To open or close the moonroof part way, push the switch in any direction while the moonroof is sliding to stop it in the desired position.

2-48 Instruments and controls

Z REVIEW COPY—2009 08+ Truck/Frontier (fro) Owners Manual—USA_English (nna) 05/27/08—debbie X

Tilting the moonroof Close the moonroof by pushing the switch to- ward UP/CLOSE s2 . Release the switch, then push the UP/CLOSE switch again to tilt the moonroof up.

To tilt the moonroof down, push the switch to- ward DOWN/OPEN s1 . Restarting the moonroof sliding switch The sliding switch will become inoperable after the battery terminal is disconnected, the electri- cal supply interrupted and/or some abnormality detected. Use the following reset procedure to return moonroof operation to normal.

1.

If the moonroof lid is open, push the tilting switch repeatedly toward the DOWN/ OPEN s1 position to fully close the lid.

2. Push and hold the tilting switch for more than 2 seconds toward the DOWN/OPEN s1 position to reestablish the lid(cid:146)s home position. The moonroof should now operate normally. Auto-reverse function (when closing or tilting down the moonroof) The auto-reverse function can be activated when the moonroof is closed or tilted down by auto-

matic operation when the ignition switch is placed in the ON position or for about 45 sec- onds after the ignition switch is placed in the OFF position. Depending on the environment or driving conditions, the auto-reverse function may be activated if an impact or load similar to something being caught in the moonroof occurs.

WARNING

There are some small distances immedi- ately before the closed position which cannot be detected. Make sure that all passengers have their hands, etc., inside the vehicle before closing the moonroof.

When closing:

If the control unit detects something caught in the moonroof as it moves to the front, the moonroof will immediately open backward. When tilting down: If the control unit detects something caught in the moonroof as it tilts down, the moonroof will im- mediately tilt up. If the auto-reverse function malfunctions and re- peats opening or tilting up the moonroof, keep pushing the tilt down switch within 5 seconds

after it happens; the moonroof will fully close gradually. Make sure nothing is caught in the moonroof.

WARNING

c In an accident you could be thrown from the vehicle through an open moonroof. Always use seat belts and child restraints.

c Do not allow anyone to stand up or extend any portion of their body out of the moonroof opening while the vehicle is in motion or while the moonroof is closing.

CAUTION

c Remove water drops, snow, ice or sand

from the moonroof before opening.

c Do not place heavy objects on the

moonroof or surrounding area.

Sunshade Open and close the sunshade by sliding it for- ward or backward. If the moonroof does not close Have your NISSAN dealer check and repair the moonroof.

Instruments and controls 2-49

Z REVIEW COPY—2009 08+ Truck/Frontier (fro) Owners Manual—USA_English (nna) 05/27/08—debbie X

INTERIOR LIGHTS

LIC0789

LIC0792

LIC0630

Type A

The interior lights have a three-position switch and operate regardless of ignition switch posi- tion. When the switch is in the ON position s1 , the interior lights illuminate, regardless of door posi- tion. The lights will go off after about 30 minutes unless the ignition switch is in the ACC or ON position.

Type B

When the switch is in the O position s2 , the interior lights will stay on for about 30 seconds when: c The doors are unlocked by the keyfob, a key or the power door lock switch while all doors are closed and the ignition switch is in the OFF position.

c The driver(cid:146)s door is opened and then closed while the key is removed from the ignition switch.

c The key is removed from the ignition switch

while all doors are closed.

Type C

The lights will turn off while the 30 second timer is activated when: c The driver(cid:146)s door is locked by the keyfob, a

key, or the power door lock switch.

c The ignition switch is turned ON. The lights will turn off automatically after 30 min- utes while doors are open to prevent the battery from becoming discharged. When the switch is in the OFF position s3 , the interior lights do not illuminate, regardless of door position.

2-50 Instruments and controls

Z REVIEW COPY—2009 08+ Truck/Frontier (fro) Owners Manual—USA_English (nna) 05/27/08—debbie X

MAP LIGHTS (if so equipped)

CAUTION

Do not use for extended periods of time with the engine stopped. This could result in a discharged battery.

LIC0791

To turn the map lights on, press the switches. To turn them off, press the switches again.

CAUTION

Do not use for extended periods of time with the engine stopped. This could result in a discharged battery.

HOMELINKT UNIVERSAL TRANSCEIVER (if so equipped)

The HomeLinkT Universal Transceiver provides a convenient way to consolidate the functions of up to three individual hand-held transmitters into one built-in device. HomeLinkT Universal Transceiver: c Will operate most Radio Frequency (RF) devices such as garage doors, gates, home and office lighting, entry door locks and se- curity systems.

c Is powered by your vehicle(cid:146)s battery. No separate batteries are required. If the vehi- cle(cid:146)s battery is discharged or is discon- nected, HomeLinkT will retain all program- ming.

Once the HomeLinkT Universal Transceiver is programmed, retain the original trans- mitter for future programming procedures (Example: new vehicle purchases). Upon sale of the programmed HomeLinkT Universal Transceiver buttons should be erased for security purposes. For additional information, refer to (cid:147)Program- ming HomeLinkT(cid:148) later in this section.

the vehicle,

Instruments and controls 2-51

Z REVIEW COPY—2009 08+ Truck/Frontier (fro) Owners Manual—USA_English (nna) 05/27/08—debbie X

WARNING

c Do not use the HomeLinkT Universal Transceiver with any garage door opener that lacks safety stop and re- verse features as required by federal safety standards. (These standards be- came effective for opener models manufactured after April 1, 1982). A ga- rage door opener which cannot detect an object in the path of a closing garage door and then automatically stop and reverse, does not meet current federal safety standards. Using a garage door opener without these features in- creases the risk of serious injury or death.

c During the programming procedure your garage door or security gate will open and close (if the transmitter is within range). Make sure that people or objects are clear of the garage door, gate, etc. that you are programming.

c Your vehicle(cid:146)s engine should be turned off while programming the HomeLinkT Universal Transceiver.

2-52 Instruments and controls

WIC0986

PROGRAMMING HOMELINKT 1. To begin, press and hold the two outer HomeLinkT buttons (to clear the memory) until the indicator light s1 blinks (after 20
seconds). Release both buttons.

2. Position the end of the hand-held transmitter 1 - 3 inches (26 - 76 mm) away from the HomeLinkT surface.

WIC0987
3. Using both hands, simultaneously press and hold both the HomeLinkT button you want to program and the hand-held transmitter but- ton.

DO NOT release the buttons until step 4 has been completed.

4. Hold down both buttons until the indicator light on the HomeLinkT flashes, changing from a (cid:147)slow blink(cid:148) to a (cid:147)rapidly flashing blink(cid:148). This could take up to 90 seconds. When the indicator light flashes rapidly, both buttons may be released. The rapidly flash- ing light indicates successful programming. To activate the garage door or other pro-

Z REVIEW COPY—2009 08+ Truck/Frontier (fro) Owners Manual—USA_English (nna) 05/27/08—debbie X

5.

grammed device, press and hold the pro- grammed HomeLinkT button (cid:151) releasing when the device begins to activate. If the indicator light on the HomeLinkT blinks rapidly for 2 seconds and then turns solid, HomeLinkT has picked up a (cid:147)rolling code(cid:148) garage door opener signal. You will need to proceed with the next steps to train the HomeLinkT to complete the programming which may require a ladder and another per- son for convenience.

6. Press and release the (cid:147)smart(cid:148) or (cid:147)learn(cid:148) pro- gram button located on the garage door opener(cid:146)s motor to activate the (cid:147)training mode(cid:148). This button is usually located near the antenna wire that hangs down from the motor. If the wire originates from under a light lens, you will need to remove the lens to access the program button.

NOTE: Once you have pressed and released the program button on the garage door open- er(cid:146)s motor and the (cid:147)training light(cid:148) is lit, you have 30 seconds in which to perform step 7. Use the help of a second person for conve- nience to assist when performing this step. 7. Within 30 seconds of pressing and releas- ing the garage door opener(cid:146)s program but-

ton, quickly and firmly press and release the HomeLinkT button you(cid:146)ve just programmed. Press and release the HomeLinkT button up to 3 times to complete the training.

8. Your HomeLinkT button should now be pro- grammed. (To program the remaining HomeLinkT buttons for additional door or gate openers, follow steps 2-4 only.)

all

previously

NOTE: Do not repeat step 1 unless you want to (cid:147)clear(cid:148) programmed HomeLinkT buttons. If you have any questions or are having difficulty programming your HomeLinkT buttons, refer to the HomeLinkT web site at: www.homelink.com or call 1-800-355-3515. PROGRAMMING HOMELINKT FOR CANADIAN CUSTOMERS Prior to 1992, D.O.C. regulations required hand- held transmitters to stop transmitting after 2 sec- onds. To program your hand-held transmitter to HomeLinkT, continue to press and hold the HomeLinkT button (see steps 2 - 4 under (cid:147)Pro- gramming HomeLinkT(cid:148)) while you press and re- press ((cid:147)cycle(cid:148)) your hand-held transmitters every 2 seconds until the indicator light flashes rapidly (indicating successful programming).

NOTE:

When programming a garage door opener, etc., it is advised to unplug the device dur- ing the (cid:147)cycling(cid:148) process to prevent pos- sible damage to the garage door opener components. OPERATING THE HOMELINKT UNIVERSAL TRANSCEIVER The HomeLinkT Universal Transceiver (once pro- grammed) may now be used to activate the ga- rage door, etc. To operate, simply press the ap- propriate programmed HomeLinkT Universal Transceiver button. The red indicator light will illuminate while the signal is being transmitted. PROGRAMMING TROUBLE- DIAGNOSIS If the HomeLinkT does not quickly learn the hand- held transmitter information: c replace the hand-held transmitter batteries

with new batteries.

c position the hand-held transmitter with its from the

facing

away

battery HomeLinkT surface.

area

c press and hold both the HomeLinkT and hand-held transmitter buttons without inter- ruption.

Instruments and controls 2-53

Z REVIEW COPY—2009 08+ Truck/Frontier (fro) Owners Manual—USA_English (nna) 05/27/08—debbie X

c position the hand-held transmitter 1 - 3
inches (26 - 76 mm) away from the HomeLinkT surface. Hold the transmitter in that position for up to 15 seconds. If HomeLinkT is not programmed within that time, try holding the transmitter in another position (cid:150) keeping the indicator light in view at all times.

If you continue to have programming difficulties, please contact the NISSAN Consumer Affairs Department. The phone numbers are located in the Foreword of this manual. CLEARING THE PROGRAMMED INFORMATION Individual buttons cannot be cleared. However, to clear all programming, press and hold the two outside buttons and release when the indicator light begins to flash (approximately 20 seconds). REPROGRAMMING A SINGLE HOMELINKT BUTTON To reprogram a HomeLinkT Universal Transceiver button, complete the following. 1. Press and hold the desired HomeLinkT but- ton. Do not release the button until step 4
has been completed.

2-54 Instruments and controls

2. When the indicator light begins to flash slowly (after 20 seconds), position the hand-held transmitter 1 - 3 inches (26 - 76
mm) away from the HomeLinkT surface.

3. Press and hold the hand-held transmitter

button.

4. The HomeLinkT indicator light will flash, first slowly and then rapidly. When the indicator light begins to flash rapidly, release both buttons.

The HomeLinkT Universal Transceiver button has now been reprogrammed. The new device can be activated by pushing the HomeLinkT button that was just programmed. This procedure will not affect any other programmed HomeLinkT buttons. IF YOUR VEHICLE IS STOLEN If your vehicle is stolen, you should change the codes of any non-rolling code device that has been programmed into HomeLinkT. Consult the Owner(cid:146)s Manual of each device or call the manu- facturer or dealer of those devices for additional information. When your vehicle is recovered, you will need to reprogram the HomeLinkT Univer- sal Transceiver with your new transmitter information.

FCC Notice: This device complies with FCC rules part 15
and RSS-210 of Industry Canada. Opera- tion is subject to the following two condi- tions: (1) This device may not cause harmful in- terference and (2) This device must accept any interference that may be received, in- cluding interference that may cause undes- ired operation. This transmitter has been tested and com- plies with FCC and DOC/MDC rules. Changes or modifications not expressly ap- proved by the party responsible for compli- ance could void the user(cid:146)s authority to op- erate the equipment. DOC: ISTC 1763K1313
FCC I.D. CV2V67690

Z REVIEW COPY—2009 08+ Truck/Frontier (fro) Owners Manual—USA_English (nna) 05/27/08—debbie X

3 Pre-driving checks and adjustments

Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2

NISSAN vehicle immobilizer system keys (if so equipped) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2
Doors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3
Locking with key. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3
Locking with inside lock knob . . . . . . . . . . . . . . . . . . . . 3-4
Locking with power door lock switch (if so equipped) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4
Rear doors (King Cab models) . . . . . . . . . . . . . . . . . . . 3-5
Automatic Door Locks . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5
Child safety rear door lock (Crew Cab models only) . . . . . . . . . . . . . . . . . . . . . . . . 3-6
Remote keyless entry system (if so equipped). . . . . . . . . 3-6
How to use remote keyless entry system . . . . . . . . . . 3-7
Hood . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-10

Fuel-filler door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-10
Fuel-filler cap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-10
Steering wheel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-12
Tilt operation (if so equipped) . . . . . . . . . . . . . . . . . . . 3-12
Sun visors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-12
Vanity mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-13
Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-13
Rearview mirror (if so equipped). . . . . . . . . . . . . . . . . 3-13
Automatic anti-glare rearview mirror (if so equipped) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-14
Outside mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-14
Truck box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-15
Tailgate. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-15
Tie down hooks (if so equipped) . . . . . . . . . . . . . . . . 3-17

Z REVIEW COPY—2009 08+ Truck/Frontier (fro) Owners Manual—USA_English (nna) 05/27/08—debbie X

Vehicle Immobilizer System keys that you have to your NISSAN dealer for registration. This is be- cause the registration process will erase the memory of all key codes previously registered into the NISSAN Vehicle Immobilizer System. After the registration process, these components will only recognize keys coded into the NISSAN Vehicle Immobilizer System during registration. Any key that is not given to your dealer at the time of registration will no longer be able to start your vehicle. Do not allow the immobilizer system key, which contains an electrical transponder, to come into contact with salt water. This could affect system function.

KEYS

does not record key numbers so it is very impor- tant to keep track of your key number plate.

A key number is only necessary when you have lost all keys and do not have one to duplicate from. If you still have a key, your NISSAN dealer can duplicate it. NISSAN VEHICLE IMMOBILIZER SYSTEM KEYS (if so equipped) You can only drive your vehicle using the master or valet keys which are registered to the NISSAN Vehicle Immobilizer System components in your vehicle. These keys have a transponder chip in the key head. The master key can be used for all the locks. The valet key cannot be used for the glove box lock. To protect belongings when you leave a key with someone, give them the valet key only. Never leave these keys in the vehicle. Additional or replacement keys: If you still have a key, the key number is not necessary when you need extra NISSAN Vehicle Immobilizer System keys. Your dealer can dupli- cate your existing key. As many as five NISSAN Vehicle Immobilizer System keys can be used with one vehicle. You should bring all NISSAN

WPD0128
1. Two master keys (black) with transponder chip (if so equipped) and chrome NISSAN brand symbol on one side.

2. Valet key (black) with transponder chip (if so

equipped)

3. Key number plate

4. Transponder chip (if so equipped)

A key number plate is supplied with your keys. Record the key number and keep the plate in a safe place (such as your wallet), not in the ve- hicle. If you lose your keys, see a NISSAN dealer for duplicates by using the key number. NISSAN

3-2 Pre-driving checks and adjustments

Z REVIEW COPY—2009 08+ Truck/Frontier (fro) Owners Manual—USA_English (nna) 05/27/08—debbie X

DOORS

WARNING

c Always have the doors locked while driving. Along with the use of seat belts, this provides greater safety in the event of an accident by helping to prevent persons from being thrown from the vehicle. This also helps keep children and others from unintentionally open- ing the doors, and will help keep out intruders.

c Before opening any door, always look

for and avoid oncoming traffic.

c Do not leave children unattended inside the vehicle. They could unknowingly ac- tivate switches or controls. Unattended children could become involved in seri- ous accidents.

Driver(cid:146)s side

WPD0311

LOCKING WITH KEY Manual To lock a door, turn the key toward the front of the vehicle s1 . To unlock, turn the key toward the rear s2 .

LPD0240

Power (if so equipped) The power door lock system allows you to lock or unlock all doors at the same time. Turning the key toward the front s1 of the vehicle locks all doors. Turning the key one time toward the rear s2 of the vehicle unlocks that door. From that position, returning the key to neutral s3 (where the key can only be removed and inserted) and turning it toward the rear again within 5 seconds unlocks all doors s4 .

Pre-driving checks and adjustments 3-3

Z REVIEW COPY—2009 08+ Truck/Frontier (fro) Owners Manual—USA_English (nna) 05/27/08—debbie X

Lockout protection When the power door lock switch (driver(cid:146)s or front passenger(cid:146)s side) is moved to the lock position with the key in the ignition and any door open, all doors will lock and then unlock auto- matically. This helps to prevent the keys from being accidently locked inside the vehicle.

LPD0298

WPD0381

Inside lock

LOCKING WITH INSIDE LOCK KNOB To lock the door without the key, move the inside lock knob to the lock position s1 , then close the door. To unlock the door without the key, move the inside lock knob to the unlock position s2 .

Door lock switch

LOCKING WITH POWER DOOR LOCK SWITCH (if so equipped) To lock all the doors without a key, push the door lock switch (driver(cid:146)s or front passenger(cid:146)s side) to the lock position s1 . When locking the door this way, be certain not to leave the key inside the vehicle.

To unlock all the doors without a key, push the door lock switch (driver(cid:146)s or front passenger(cid:146)s side) to the unlock position s2 .

3-4 Pre-driving checks and adjustments

Z REVIEW COPY—2009 08+ Truck/Frontier (fro) Owners Manual—USA_English (nna) 05/27/08—debbie X

REAR DOORS (King Cab models) 1. Open the driver(cid:146)s or passenger(cid:146)s door.

LPD0278

LPD0312
2. From the outside, pull the door handle sA

toward you.

WPD0313

3. Open the door to the desired position. AUTOMATIC DOOR LOCKS c All doors will be locked automatically when the vehicle speed reaches 15 MPH (24 km/ h).

c All the doors will unlock automatically when the ignition switch is placed in the OFF position.

Pre-driving checks and adjustments 3-5

Z REVIEW COPY—2009 08+ Truck/Frontier (fro) Owners Manual—USA_English (nna) 05/27/08—debbie X

The automatic lock and unlock functions can be deactivated or activated indepen- dently of each other. To deactivate or activate the automatic door lock or unlock system, per- form the following procedure: 1. Close all doors. 2. Place the ignition switch in the ON position. 3. Do one of the following within 20 seconds of

performing Step #2: c To change AUTO UNLOCK settings: push and hold the power door lock switch to the position (UNLOCK) for more than 5 seconds.

c To change AUTO LOCK settings: push and hold the power door lock switch to the position (LOCK) for more than 5 seconds.

4. When activated, the hazard indicator will flash twice. When deactivated, the hazard indicator will flash once.

5. The ignition switch must be placed in the OFF and ON position again between each setting change.

3-6 Pre-driving checks and adjustments

WPD0314
CHILD SAFETY REAR DOOR LOCK (Crew Cab models only) Child safety locks help prevent the rear doors from being opened accidentally, especially when small children are in the vehicle. The child safety lock levers are located on the edge of the rear doors. When the lever is in the lock position, the door can be opened only from the outside.

REMOTE KEYLESS ENTRY SYSTEM (if so equipped)

WARNING

c Radio waves could adversely affect electric medical equipment. Those who use a pacemaker should contact the electric medical equipment manufac- turer for the possible influences before use.

c The remote keyless entry keyfob trans- mits radio waves when the buttons are pushed. The FAA advises radio waves may affect aircraft navigation and com- munication systems. Do not operate the remote keyless entry keyfob while on an airplane. Make sure the buttons are not operated unintentionally when the unit is stored for a flight

It is possible to lock/unlock all doors, turn the interior lights on, and activate the panic alarm by using the keyfob from outside the vehicle. Be sure to remove the key from the vehicle before locking the doors.

The keyfob can operate at a distance of approxi- mately 33 ft (10 m) from the vehicle. The effective distance depends on the conditions around the vehicle.

Z REVIEW COPY—2009 08+ Truck/Frontier (fro) Owners Manual—USA_English (nna) 05/27/08—debbie X

As many as 5 keyfobs can be used with one vehicle. For information concerning the purchase and use of additional keyfobs, contact a NISSAN dealer.

The keyfob will not function when: c the battery is discharged c the distance between the vehicle and the

keyfob is over 33 ft (10 m)

The panic alarm will not activate when the key is in the ignition switch.

CAUTION

Listed below are conditions or occur- rences which will damage the keyfob: c Do not allow the keyfob to become wet. immediately

If the keyfob gets wet, wipe until it is completely dry.

c Do not drop the keyfob. c Do not strike the keyfob sharply against

another object.

c Do not place the keyfob for an extended period in an area where temperatures exceed 140(cid:176)F (60(cid:176)C).

c Do not attach the keyfob with a key

holder that contains a magnet.

c Do not place the keyfob near equip- ment that produces a magnetic field, such as a TV, audio equipment and per- sonal computers.

If a keyfob is lost or stolen, NISSAN rec- ommends erasing the ID code of that key- fob. This will prevent the keyfob from un- authorized use to unlock the vehicle. For information regarding the erasing proce- dure, please contact a NISSAN dealer.

LPD0209

HOW TO USE REMOTE KEYLESS ENTRY SYSTEM Locking doors 1. Close all windows.

2. Remove the key from the ignition switch.

3. Close the hood and all doors.

4. Push the

button on the keyfob. All the doors lock. The hazard warning lights flash twice and the horn beeps once to indicate all doors are locked.

Pre-driving checks and adjustments 3-7

Z REVIEW COPY—2009 08+ Truck/Frontier (fro) Owners Manual—USA_English (nna) 05/27/08—debbie X

c When the

button is pushed with all doors locked, the hazard warning lights flash twice and the horn beeps once as a reminder the doors are already locked.

that

c If a door

is open and you push the lock button, the doors will but the horn will not beep and the hazard lights will not flash.

The horn may or may not beep. Refer to (cid:147)Silenc- ing the horn beep feature(cid:148) later in this section for details.

3-8 Pre-driving checks and adjustments

LPD0210

Unlocking doors

button on the keyfob once.

Push the c Only the driver(cid:146)s door unlocks. c The hazard warning lights flash once if all doors are completely closed with the ignition switch in any position except the ON posi- tion.

c The interior lights illuminate for 30 seconds when the interior light switch is in the normal operation position.

Push the 5 seconds.

button on the keyfob again within

c All doors unlock. c The hazard warning lights flash once if all

doors are completely closed.

The interior lights can be turned off without wait- ing 30 seconds by inserting the key into the ignition switch and turning to the ON or START position, locking the doors with the keyfob or pushing the interior light switch to the OFF posi- tion. Auto relock When the button on the keyfob is pushed, all doors will lock automatically within one minute unless one of the following operations is per- formed: c Any door is opened. c A key is inserted into the ignition switch and

the switch is turned from OFF to ON.

Z REVIEW COPY—2009 08+ Truck/Frontier (fro) Owners Manual—USA_English (nna) 05/27/08—debbie X

The hazard warning lights will flash once and the horn will sound once to confirm that the horn beep feature has been reactivated. Deactivating the horn beep feature does not si- lence the horn if the alarm is triggered. Using the interior lights Push the on the interior lights. For additional information, refer to (cid:147)Interior lights(cid:148) in the (cid:147)Instruments and controls(cid:148) section earlier in this manual.

button on the keyfob once to turn

LPD0211

LPD0262

Using the panic alarm If you are near your vehicle and feel threatened, you may activate the panic alarm to call attention by pushing and holding the button on the keyfob for longer than 0.5 seconds. The panic alarm and headlights will stay on for 25
seconds. The panic alarm stops when: c it has run for 25 seconds, or c any button is pushed on the keyfob.

Silencing the horn beep feature If desired, the horn beep feature can be deacti- vated using the keyfob.

To deactivate: Press and hold the and

buttons for at least 2 seconds.

The hazard warning lights will flash three times to confirm that the horn beep feature has been deactivated.

To activate: Press and hold the and once more.

buttons for at least 2 seconds

Pre-driving checks and adjustments 3-9

Z REVIEW COPY—2009 08+ Truck/Frontier (fro) Owners Manual—USA_English (nna) 05/27/08—debbie X

HOOD

FUEL-FILLER DOOR

WARNING

c Make sure the hood is completely closed and latched before driving. Fail- ure to do so could cause the hood to fly open and result in an accident.

c If you see steam or smoke coming from the engine compartment, to avoid injury do not open the hood.

LPD0302
s1 Pull the hood lock release handle located below the driver(cid:146)s side instrument panel. The hood will spring up slightly.

s2 Push the lever at the front of the hood to the side as illustrated with your fingertips and raise the hood.

s3

Insert the support rod into the slot on the underside of the hood.

When closing the hood, return the hood rod to it(cid:146)s original position. Lower the hood approxi- mately 12 inch (30 cm) above the latch and release it. This allows proper engagement of the hood latch.

3-10 Pre-driving checks and adjustments

LPD0263

FUEL-FILLER CAP The fuel-filler cap is a ratcheting type. Turn the cap counterclockwise to remove. To tighten, turn the cap clockwise until ratcheting clicks are heard.

Z REVIEW COPY—2009 08+ Truck/Frontier (fro) Owners Manual—USA_English (nna) 05/27/08—debbie X

(cid:150) Always place the container on the

ground when filling.

(cid:150) Do not use electronic devices when

filling.

(cid:150) Keep the pump nozzle in contact with the container while you are fill- ing it.

(cid:150) Use only approved portable fuel con-

tainers for flammable liquid.

c Fuel may be under pressure. Turn the cap a third of a turn, and wait for any (cid:147)hissing(cid:148) sound to stop to prevent fuel from spraying out and possibly causing personal injury. Then remove the cap.

c Do not attempt to top off the fuel tank after the fuel pump nozzle shuts off automatically. Continued refueling may cause fuel overflow, resulting in fuel spray and possibly a fire.

c Use only an original equipment type fuel-filler cap as a replacement. It has a built-in safety valve needed for proper operation of the fuel system and emis- sion control system. An incorrect cap can result in a serious malfunction and possible injury. It could also cause the malfunction indicator lamp to come on. c Never pour fuel into the throttle body to

attempt to start your vehicle.

c Do not fill a portable fuel container in the vehicle or trailer. Static electricity can cause an explosion of flammable liquid, vapor or gas in any vehicle or trailer. To reduce the risk of serious injury or death when filling portable fuel containers:

LPD0325
Loop the tether strap around the hook s1 while refueling.

WARNING

c Gasoline is extremely flammable and highly explosive under certain condi- tions. You could be burned or seriously