2008 Nissan Frontier Owners Manual

turned to OFF or the vehicle is shut off, even is turned to a if the air flow control dial position other than the position. This dehumidifies the air which helps defog the windshield. The mode automatically

4-4 Heater, air conditioner, audio and phone systems

Z REVIEW COPY—2008 08+ Truck/Frontier (fro) Owners Manual—USA_English (nna) 06/30/07—debbie X

turns off, allowing outside air to be drawn into the passenger compartment to further improve the defogging performance.

3. Turn the temperature control dial to the de- sired position between the middle and the hot position.

Bi-level heating This mode directs cooler air from the side and center vents and warmer air from the floor outlets. When the temperature control dial is moved to the full hot or full cool position, the air between the vents and the floor outlets is the same tem- perature.

1. Push the

button to the off position.

2. Turn the air flow control dial to the

position.

3. Turn the fan control dial to the desired posi-

tion.

4. Turn the temperature control dial to the de-

sired position.

Heating and defogging This mode heats the interior and defogs the wind- shield.

1. Turn the air flow control dial to the

position.

2. Turn the fan control dial to the desired posi-

tion.

c When the

position is selected, the air conditioner automatically turns on (however, the indicator light on the button will not come on) if the outside temperature is more than 36(cid:176)F (2(cid:176)C). If in defrost mode for more than one minute, the air conditioning system will continue to operate until the fan control dial is turned to OFF or the vehicle is shut off, even if the air flow control dial is turned to a position other than the position. This dehumidifies the air which helps defog the windshield. The mode automatically turns off, allowing out- side air to be drawn into the passenger compartment to further improve the defog- ging performance.

Operating tips Clear snow and ice from the wiper blades and air inlet in front of the windshield. This improves heater operation.

AIR CONDITIONER OPERATION (if so equipped) Start the engine, turn the fan control dial to the desired (1 - 4) position, and push in the button to activate the air conditioner. When the air conditioner is on, cooling and dehumidifying functions are added to the heater operation. The air conditioner cooling function oper- ates only when the engine is running. Cooling This mode is used to cool and dehumidify the air. 1. Push the 2. Turn the air flow control dial to the

button to the off position.

position.

3. Turn the fan control dial to the desired posi-

tion.

4. Push the comes on.

button. The indicator light

5. Turn the temperature control dial to the de-

sired position.

c For quick cooling when the outside tem- perature is high, push the button to the on position (indicator light on). Be sure to return the button to the off position for normal cooling.

Heater, air conditioner, audio and phone systems 4-5

Z REVIEW COPY—2008 08+ Truck/Frontier (fro) Owners Manual—USA_English (nna) 06/30/07—debbie X

Dehumidified heating This mode is used to heat and dehumidify the air. 1. Push the 2. Turn the air flow control dial to the

button to the off position.

position.

3. Turn the fan control dial to the desired posi-

tion.

4. Push the comes on.

button. The indicator light

5. Turn the temperature control dial to the de-

sired position.

Dehumidified defogging This mode is used to defog the windows and dehumidify the air. 1. Turn the air flow control dial to the

position.

2. Turn the fan control dial to the desired posi-

tion.

3. Push the comes on.

button. The indicator light

or positions in between When the are selected, the air conditioner automatically turns on (however, the indicator light will not illuminate) if the outside temperature is more than 36(cid:176)F (2(cid:176)C). The air conditioning system will con- tinue to operate until the fan control dial is turned to OFF or the vehicle is shut off, even if the air flow is turned to a position other than control dial position. This dehumidifies the air the which helps defog the windshield. The mode automatically turns off, allowing outside air to be drawn into the passenger compartment to further improve the defogging performance. 4. Turn the temperature control dial to the de-

sired position. Operating tips c Keep the windows and sunroof

(if so equipped) closed while the air conditioner is in operation.

c After parking in the sun, drive for 2 or 3
minutes with the windows open to vent hot air from the passenger compartment. Then, close the windows. This allows the air con- ditioner to cool the interior more quickly.

c The air conditioning system should be operated for approximately 10 minutes at least once a month. This helps pre- vent damage to the system due to lack of lubrication.

c A visible mist may be seen coming from the ventilators in hot, humid conditions as the air is cooled rapidly. This does not indicate a malfunction.

c If

the engine coolant

temperature gauge indicates engine coolant tem- perature over the normal range, turn the air conditioner off. See (cid:147)If your vehicle overheats(cid:148) in the (cid:147)In case of emergency(cid:148) section of this manual.

AIR FLOW CHARTS The following charts show the button and dial positions for MAXIMUM AND QUICK heating, cooling or defrosting. For additional information on heating and cooling see (cid:147)Heater and air con- ditioner(cid:148) in this section(cid:148). The air recirculation ) button should always be in the OFF position for heating and defrosting.

4-6 Heater, air conditioner, audio and phone systems

Z REVIEW COPY—2008 08+ Truck/Frontier (fro) Owners Manual—USA_English (nna) 06/30/07—debbie X

WHA0775

WHA0776

Heater, air conditioner, audio and phone systems 4-7

Z REVIEW COPY—2008 08+ Truck/Frontier (fro) Owners Manual—USA_English (nna) 06/30/07—debbie X

4-8 Heater, air conditioner, audio and phone systems

WHA0777

WHA0778

Z REVIEW COPY—2008 08+ Truck/Frontier (fro) Owners Manual—USA_English (nna) 06/30/07—debbie X

SERVICING AIR CONDITIONER

The air conditioner system in your NISSAN ve- hicle is charged with a refrigerant designed with the environment in mind. This refrigerant does not harm the earth(cid:146)s ozone layer. Special charging equipment and lubricant is re- quired when servicing your NISSAN air condi- tioner. Using improper refrigerants or lubricants will cause severe damage to your air conditioner system. See (cid:147)Air conditioner system refrigerant and lubricant recommendations(cid:148) in the (cid:147)Techni- cal and consumer information(cid:148) section of this manual. A NISSAN dealer is able to service your (cid:147)environ- mentally friendly(cid:148) air conditioning system.

WARNING

The air conditioner system contains re- frigerant under high pressure. To avoid personal injury, any air conditioner ser- vice should be done only by an experi- enced technician with proper equipment.

WHA0779

Heater, air conditioner, audio and phone systems 4-9

Z REVIEW COPY—2008 08+ Truck/Frontier (fro) Owners Manual—USA_English (nna) 06/30/07—debbie X

AUDIO SYSTEM

RADIO Turn the ignition key to the ACC or ON position and press the PWR (power)/VOL (volume) knob to turn the radio on. If you listen to the radio with the engine not running, the key should be turned to the ACC position.

Radio reception is affected by station signal strength, distance from radio transmitter, build- ings, bridges, mountains and other external influ- ences. Intermittent changes in reception quality normally are caused by these external influences. Using a cellular phone in or near the ve- hicle may influence radio reception quality. Radio reception Your NISSAN radio system is equipped with state-of-the-art electronic circuits to enhance ra- dio reception. These circuits are designed to extend reception range, and to enhance the qual- ity of that reception.

However there are some general characteristics of both FM and AM radio signals that can affect radio reception quality in a moving vehicle, even when the finest equipment is used. These char- acteristics are completely normal in a given re- ception area, and do not indicate any malfunction in your NISSAN radio system.

Reception conditions will constantly change be- cause of vehicle movement. Buildings, terrain, signal distance and interference from other ve- hicles can work against ideal reception. De- scribed below are some of the factors that can affect your radio reception. Some cellular phones or other devices may cause interference or a buzzing noise to come from the audio system speakers. Storing the de- vice in a different location may reduce or elimi- nate the noise. FM RADIO RECEPTION Range: FM range is normally limited to 25 (cid:150) 30 mi (40 (cid:150) 48 km), with monaural (single channel) FM having slightly more range than stereo FM. Exter- nal influences may sometimes interfere with FM station reception even if the FM station is within 25 mi (40 km). The strength of the FM signal is directly related to the distance between the transmitter and receiver. FM signals follow a line- of-sight path, exhibiting many of the same char- acteristics as light. For example, they will reflect off objects. Fade and drift: As your vehicle moves away from a station transmitter, the signals will tend to fade and/or drift.

Static and flutter: During signal interference from buildings, large hills or due to antenna position (usually in conjunction with increased distance from the station transmitter) static or flutter can be heard. This can be reduced by adjusting the treble control to reduce treble response. Multipath reception: Because of the reflective characteristics of FM signals, direct and reflected signals reach the receiver at the same time. The signals may cancel each other, resulting in mo- mentary flutter or loss of sound. AM RADIO RECEPTION AM signals, because of their low frequency, can bend around objects and skip along the ground. In addition, the signals can be bounced off the ionosphere and bent back to earth. Because of these characteristics, AM signals are also sub- ject to interference as they travel from transmitter to receiver. Fading: Occurs while the vehicle is passing through freeway underpasses or in areas with many tall buildings. It can also occur for several seconds during ionospheric turbulence even in areas where no obstacles exist. Static: Caused by thunderstorms, electrical power lines, electric signs and even traffic lights.

4-10 Heater, air conditioner, audio and phone systems

Z REVIEW COPY—2008 08+ Truck/Frontier (fro) Owners Manual—USA_English (nna) 06/30/07—debbie X

SATELLITE RADIO RECEPTION (if so equipped) When the satellite radio is first installed or the battery has been replaced, the satellite radio may not work properly. This is not a malfunction. Wait more than 10 minutes with satellite radio ON and the vehicle outside of any metal or large building for satellite radio to receive all of the necessary data. No satellite radio reception is available and (cid:147)NO SAT(cid:148) is displayed when the SAT band option is selected unless optional satellite receiver and antenna are installed and an XMT satellite radio service subscription is active. Satellite radio can only be installed in vehicles that were factory pre-wired for satellite radio. Satellite radio is not available in Alaska, Hawaii and Guam. Satellite radio performance may be affected if cargo carried on the roof blocks the satellite radio signal. If possible, do not put cargo over the satellite antenna. A build up of ice on the satellite radio antenna can affect satellite radio performance. Remove the ice to restore satellite radio reception

Compact disc (CD) player

CAUTION

c Do not force a compact disc into the CD insert slot. This could damage the CD and/or CD changer/player.

c Trying to load a CD with the CD door closed could damage the CD and/or CD changer.

c Only one CD can be loaded into the CD

player at a time.

c Only use high quality 4.7 inches (12 cm) round discs that have the (cid:147)COMPACT disc DIGITAL AUDIO(cid:148) logo on the disc or packaging.

c During cold weather or rainy days, the player may malfunction due to the hu- midity. If this occurs, remove the CD and dehumidify or ventilate the player completely.

c The player may skip while driving on

rough roads.

LHA0099
AUDIO OPERATION PRECAUTIONS

c The CD player sometimes cannot func- tion when the compartment tempera- ture low. Decrease/increase the temperature before use.

extremely high or

is

Heater, air conditioner, audio and phone systems 4-11

Z REVIEW COPY—2008 08+ Truck/Frontier (fro) Owners Manual—USA_English (nna) 06/30/07—debbie X

c Do not expose the CD to direct sun-

light.

c CDs that are in poor condition or are dirty, scratched or covered with finger- prints may not work properly.

c The following CDs may not work prop-

erly: c Copy control compact discs (CCCD) c Recordable compact discs (CD-R) c Rewritable compact discs (CD-RW) c Do not use the following CDs as they may cause the CD player to malfunc- tion: c 3.1 in (8 cm) discs with an adapter c CDs that are not round c CDs with a paper label c CDs that are warped, scratched, or

have abnormal edges

c This audio system can only play pre- recorded CDs. It has no capability to record or burn CDs.

c If the CD cannot be played, one of the following messages will be displayed.

CHECK DISC: c Confirm that the CD is inserted cor- rectly (the label side is facing up, etc.).

c Confirm that the CD is not bent or

warped and it is free of scratches.

PRESS EJECT:

This is an error due to excessive tem- perature inside the player. Remove the CD by pressing the EJECT button. After a short time, reinsert the CD. The CD can be played when the temperature of the player returns to normal. UNPLAYABLE: The file is unplayable in this audio sys- tem (only MP3 or WMA CD).

Compact Disc with MP3 or WMA Terms: c MP3 (cid:151) MP3 is short for Moving Pictures Experts Group Audio Layer 3. MP3 is the most well-known compressed digital audio file format. This format allows for near (cid:147)CD quality(cid:148) sound, but at a fraction of the size of normal audio files. MP3 conversion of an audio track from CD-ROM can reduce the file size by approximately a 10:1 ratio with

virtually no perceptible loss in quality. MP3
compression removes the redundant and irrelevant parts of a sound signal that the human ear doesn(cid:146)t hear.

c WMA (cid:151) Windows Media Audio (WMA)* is a compressed audio format created by Mi- crosoft as an alternative to MP3. The WMA codec offers greater file compression than the MP3 codec, enabling storage of more digital audio tracks in the same amount of space when compared to MP3s at the same level of quality.

c Bit rate (cid:151) Bit rate denotes the number of bits per second used by a digital music file. The size and quality of a compressed digital audio file is determined by the bit rate used when encoding the file.

c Sampling frequency (cid:151) Sampling frequency is the rate at which the samples of a signal are converted from analog to digital (A/D conversion) per second.

c Multisession (cid:151) Multisession is one of the methods for writing data to media. Writing data once to the media is called a single session, and writing more than once is called a multisession.

4-12 Heater, air conditioner, audio and phone systems

Z REVIEW COPY—2008 08+ Truck/Frontier (fro) Owners Manual—USA_English (nna) 06/30/07—debbie X

c ID3/WMA Tag (cid:151) The ID3/WMA tag is the part of the encoded MP3 or WMA file that contains information about the digital music file such as song title, artist, encoding bit rate, track time duration, etc. ID3 tag infor- mation is displayed on the Artist/song title line on the display.

* WindowsT and Windows MediaT are regis- tered trademarks and trademarks in the United States of America and other countries of Mi- crosoft Corporation of the USA.

Playback order: Music playback order of a CD with MP3 or WMA files is as illustrated. c The names of folders not containing MP3 or

WMA files are not shown in the display.

c If there is a file in the top level of the disc,

(cid:147)Root Folder(cid:148) is displayed.

c The playback order is the order in which the files were written by the writing software. Therefore, the files might not play in the desired order.

WHA1078

Playback order chart

Heater, air conditioner, audio and phone systems 4-13

Z REVIEW COPY—2008 08+ Truck/Frontier (fro) Owners Manual—USA_English (nna) 06/30/07—debbie X

Specification chart:

Supported media Supported file systems

Supported versions*1

MP3

WMA

Version Sampling frequency Bit rate Version Sampling frequency Bit rate

Tag information Folder levels Text character number limitation

Displayable character codes*2

CD, CD-R, CD-RW ISO9660 LEVEL1, ISO9660 LEVEL2, Apple ISO, Romeo, Joliet * ISO9660 Level 3 (packet writing) is not supported. MPEG1, MPEG2, MPEG2.5
8 kHz - 48 kHz 8 kbps - 320 kbps, VBR WMA7, WMA8, WMA9
32 kHz - 48 kHz 48 kbps - 192 kbps, VBR ID3 tag VER1.0, VER1.1, VER2.2, VER2.3 (MP3 only) Folder levels: 8, Max folders: 255 (including root folder), Files: 512 (Max. 255 files for one folder) 128 characters 01: ASCII, 02: ISO-8859-1, 03: UNICODE (UTF-16 BOM Big Endian), 04: UNICODE (UTF-16 Non-BOM Big Endian), 05: UNICODE (UTF-8), 06: UNICODE (Non-UTF-16 BOM Little Endian)

*1 Files created with a combination of 48 kHz sampling frequency and 64 kbps bit rate cannot be played.

*2 Available codes depend on what kind of media, versions and information are going to be displayed.

4-14 Heater, air conditioner, audio and phone systems

Z REVIEW COPY—2008 08+ Truck/Frontier (fro) Owners Manual—USA_English (nna) 06/30/07—debbie X

Troubleshooting guide:

Symptom

Cannot play

Poor sound quality

It takes a relatively long time before the music starts playing.

Music cuts off or skips

Skipping with high bit rate files Moves immediately to the next song when playing Songs do not play back in the desired order

Cause and Countermeasure

Check if the disc was inserted correctly. Check if the disc is scratched or dirty. Check if there is condensation inside the player. If there is, wait until the condensation is gone (about 1 hour) before using the player. If there is a temperature increase error, the CD player will play correctly after it returns to the normal temperature. Files with extensions other than (cid:147).MP3(cid:148), (cid:147).mp3(cid:148) or (cid:147).wma(cid:148) cannot be played. In addition, the character codes and number of characters for folder names and file names should be in compliance with the specifications. Check if the finalization process, such as session close and disc close, is done for the disc. Check if the disc is protected by copyright. Check if the disc is scratched or dirty. Bit rate may be too low. If there are many folders or file levels on the MP3/WMA disc, or if it is a multisession disc, some time may be required before the music starts playing.

The writing software and hardware combination might not match, or the writing speed, writing depth, writing width, etc., might not match the specifications. Try using the slowest writing speed. Skipping may occur with large quantities of data, such as for high bit rate data.

When a non-MP3/WMA file has been given an extension of (cid:147).MP3(cid:148), (cid:147).WMA(cid:148), .(cid:147)mp3(cid:148)or (cid:147).wma(cid:148), or when play is prohibited by copyright protection, there will be approximately 5 seconds of no sound and then the player will skip to the next song. The playback order is the order in which the files were written by the writing software. Therefore, the files might not play in the desired order.

Heater, air conditioner, audio and phone systems 4-15

Z REVIEW COPY—2008 08+ Truck/Frontier (fro) Owners Manual—USA_English (nna) 06/30/07—debbie X

FM/AM RADIO WITH COMPACT DISC (CD) PLAYER (if so equipped) For all operation precautions, see 9Audio opera- tion precautions9 earlier in this section. PWR/VOL control knob

Turn the ignition key to the ACC or ON position, then press the PWR/VOL control knob. If you listen to the radio with the engine not running, turn the key to the ACC position. The mode (radio or CD) that was playing immediately before the system was turned off resumes playing. When no CD is loaded, the radio comes on. Pressing the PWR/VOL control knob again turns the system off. Turn the PWR/VOL control knob to the right to increase volume or to the left to decrease volume. AUDIO button (Bass, Treble, Fade, Bal- ance): Press the AUDIO button to change the mode as follows: BASS ! TREB ! FAD ! BAL ! Audio ! BASS To adjust Bass, Treble, Fade and Balance, press the AUDIO button until the desired mode ap- pears in the display. Press the SEEK/TRACK button to adjust Bass and Treble to the desired

WHA0586

PRESET A•B•C button Display screen

1. 2. 3. CD button 4. 5. CD insert slot 6. MENU button 4-16 Heater, air conditioner, audio and phone systems

CD eject button

AUDIO button Station select (1 - 6) buttons SEEK/TRACK (FF/REV) button

7. 8. 9. 10. PWR/VOL control knob 11. BAND button

Z REVIEW COPY—2008 08+ Truck/Frontier (fro) Owners Manual—USA_English (nna) 06/30/07—debbie X

level. You can also use the SEEK/TRACK button to adjust Fader and Balance modes. Fader ad- justs the sound level between the front and rear speakers and Balance adjusts the sound be- tween the right and left speakers. Once you have adjusted the sound quality to the desired level, press the AUDIO button repeatedly until the radio or CD display reappears. Other- wise, the radio or CD display will automatically reappear after about 7 seconds. Clock set 1. Press and hold the MENU button until

it beeps (for more than 2 seconds) to enter the clock set mode.

2. The hours will start SEEK/TRACK button just the hours.

flashing. Press the to ad-

or

3. Press the MENU button until the radio beeps

to switch to the minute adjustment.

4. The minutes will start flashing. Press the to ad-

or

SEEK/TRACK button just the minutes.

5. Press the MENU button again to exit the

clock set mode.

The display will return to the regular clock display after 7 seconds, or press the MENU button again to return to the regular clock display.

FM/AM radio operation FM/AM band select: Pressing the BAND button will change the band as follows: AM ˆ! FM When the BAND button is pressed while the ignition switch is in the ACC or ON position, the radio will come on at the station last played. If a compact disc is playing when the BAND button is pressed, the compact disc will auto- matically be turned off and the last radio station played will come on. The FM stereo indicator, ST, illuminates during FM stereo reception. When the stereo broadcast signal is weak, the radio automatically changes from stereo to monaural reception. MENU button: Press the MENU button while the radio is playing to change the tuning mode as follows: SEEK tuning mode ! TUNE mode ! SCAN tuning mode TUNE and SCAN are shown in the display win- dow for each mode. No icon is displayed for SEEK tuning.

SEEK tuning

or

While in SEEK tuning mode, press the SEEK/TRACK button for less than 1.5 seconds. SEEK tuning begins from low to high frequencies or high to low frequencies, depending on which button is pressed, and stops at the next broadcasting station. Press the button, once the highest broadcasting station is reached, the radio continues in the SEEK mode at the lowest broadcasting station. Press the button, once the lowest broadcasting station is reached, the radio continues in the SEEK mode at the highest broadcasting station.

Manual tuning

While in TUNE mode, press the SEEK/TRACK button for manual tuning. Press and hold the SEEK/TRACK button or

to move quickly through the channels.

or

SCAN tuning

or

While in SCAN tuning mode, press and hold the SEEK/TRACK button for more than 1.5 seconds. Scan tuning begins from low to high frequencies or high to low frequencies, depending on which SEEK/TRACK button is pressed. scan tuning stops at each broadcasting station Heater, air conditioner, audio and phone systems 4-17

or

Z REVIEW COPY—2008 08+ Truck/Frontier (fro) Owners Manual—USA_English (nna) 06/30/07—debbie X

for 5 seconds. When scanning, SCAN illumi- nates in the display and the radio station blinks. When temporarily stopped on a station, SCAN blinks and the radio station display is solid. Pressing again during this 5 second period stops or scan tuning and the radio remains tuned to that radio station. Station memory operations:

the SEEK/TRACK button

18 stations can be set for the FM and AM radio to the A, B and C preset button in any combination of AM or FM stations.

1. Press the PRESET A•B•C button to change between storage banks. The radio displays the icon A, B or C to indicate which set of presets are active.

2. Tune to the desired station using manual TUNE or SEEK tuning. Press and hold any of the desired station memory buttons (1 (cid:150) 6) until a beep sound is heard. (The radio mutes when the select button is pressed.)

3. The channel indicator will then come on and the sound will resume. Programming is now complete.

4. Other buttons can be set in the same man-

ner.

If the battery cable is disconnected, or if the fuse opens, the radio memory will be canceled. In that case, reset the desired stations. Compact disc (CD) player operation Turn the ignition key to the ACC or ON position, and carefully insert the compact disc into the slot with the label side up. The compact disc is auto- matically pulled into the slot and starts to play.

If the radio is already operating, it automatically turns off and the compact disc begins to play. CD button:

When the CD button is pressed with a compact disc loaded and the radio playing, the radio turns off and the compact disc starts to play.

SEEK/TRACK button:

the SEEK/TRACK button

is When pressed while the compact disc is playing, the next track following the present one starts to play from the beginning. Press SEEK/TRACK button several times to skip several tracks. Each time the button is pressed, the CD ad- vances 1 additional track. The track number ap- pears in the display window. (When the last track on the compact disc is skipped, the first track is played.)

4-18 Heater, air conditioner, audio and phone systems

is pressed, When SEEK/TRACK button the track being played returns to the beginning. Press SEEK/TRACK button several times to skip back several tracks. Each time the button is pressed the CD moves back 1 track.

SEEK/TRACK (FF/REV) button:

Press and hold the SEEK/TRACK button or while a compact disc is playing, the compact disc plays at an increased speed while fast forwarding or rewinding. When the button is released, the compact disc returns to normal play speed. MENU button: When the MENU button is pressed while the compact disc is playing, the play pattern changes as follows: RPT ˆ! MIX ˆ! Normal RPT: The track that is currently playing will be repeated. MIX: The order of the tracks on the disc will be mixed during play, not following the sequence on the compact disc. The same track may be re- peated twice. Press the button while in the MIX mode and tracks will be chosen at random. When a new compact disc is inserted, the play pattern automatically changes to normal.

Z REVIEW COPY—2008 08+ Truck/Frontier (fro) Owners Manual—USA_English (nna) 06/30/07—debbie X

CD EJECT:

button is pressed with a com- the compact disc will be

When the pact disc loaded, ejected. When the button is pressed while the compact disc is playing, the compact disc will eject and the system will turn off. CD IN indicator: This a CD is loaded with the audio system on.

indicator appears on the display when

WHA0735

PRESET A•B•C button Display screen DISP/CLOCK button SEEK/TRACK button

1. 2. 3. 4. 5. CD button 6.

RADIO button*

AUX button SCAN RPT button

7. 8. 9. CAT FOLDER button 10. 11. CD insert slot 12.

LOAD button

CD eject button

Heater, air conditioner, audio and phone systems 4-19

Z REVIEW COPY—2008 08+ Truck/Frontier (fro) Owners Manual—USA_English (nna) 06/30/07—debbie X

13. PWR/VOL control knob 14. Station and CD select (1 (cid:150) 6) buttons 15. AUDIO and TUNE button

*No satellite radio reception is available when the RADIO button is pressed to access satellite radio stations unless optional satellite receiver and antenna are installed and an XMT satellite radio service subscription is active. Satellite radio can only be installed in vehicles that were factory pre-wired for satellite radio. Satellite radio is not available in Alaska, Hawaii and Guam. FM/AM/SAT RADIO WITH COMPACT DISC (CD) CHANGER For all operation precautions, see 9Audio opera- tion precautions9 earlier in this section. No satellite radio reception is available when the RADIO button is pressed to access satellite radio stations unless optional satellite receiver and an- tenna are installed and an XMT satellite radio service subscription is active. Satellite radio can only be installed in vehicles that were factory pre-wired for satellite radio. Satellite radio is not available in Alaska, Hawaii and Guam.

Audio main operation POWER/VOLUME control:

Turn the ignition key to ACC or ON, and then press the PWR/VOL control knob while the sys- tem is off to call up the mode (radio or CD) which was playing immediately before the system was turned off.

To turn the system off, press the PWR/VOL con- trol knob.

Turn the PWR/VOL control knob to adjust the volume.

This vehicle may be equipped with Speed Sen- sitive Volume (SSV) for audio. The audio volume changes as the driving speed changes. AUDIO knob (Bass, Treble, Fade and Bal- ance):

Press the AUDIO knob to change the mode as follows: Bass ! Treble ! Fade ! Balance To adjust Bass, Treble, Fade and Balance, press the AUDIO knob until the desired mode appears in the display. Turn the Tuning knob to adjust Bass and Treble to the desired level. You can also use the Tuning knob to adjust Fader and Balance modes. Fader adjusts the sound level between

4-20 Heater, air conditioner, audio and phone systems

the front and rear speakers and Balance adjusts the sound between the right and left speakers.

Once you have adjusted the sound quality to the desired level, press the AUDIO knob repeatedly until the radio or CD display reappears. Other- wise, the radio or CD display will automatically reappear after about 10 seconds. Clock set

1. Press the DISP/CLOCK button until

it

beeps (>1.5 seconds).

2. The hours will start flashing. Press the CAT button or SEEK button to adjust the

or

or

FOLDER TRACK hours.

3. Press the DISP/CLOCK button again to

switch to the minute adjustment.

4. Press the CAT FOLDER button or SEEK TRACK button to adjust the minutes.

or or

5. Press the DISP/CLOCK button again to exit

the clock set mode.

The display will return to the regular clock display after 7 seconds, or you may press the DISP/CLOCK button again to return to the regu- lar clock display.

Z REVIEW COPY—2008 08+ Truck/Frontier (fro) Owners Manual—USA_English (nna) 06/30/07—debbie X

DISP (display) button:

This DISP (display) button will show text about MP3, SAT or CD information in the audio display. CD display mode

To change the text displayed while playing a CD with text, press the DISP button. The DISP button will allow you to scroll through CD text as follows: Disc title ˆ! Track title. To change the default display mode, press the AUDIO knob repeatedly until DISPLAY MODE appears on the display, then rotate the knob to select the following display modes: Disc number ˆ! Folder number. Once the display mode is selected, press the AUDIO knob again to store the setting. If the AUDIO knob is not pressed within 8 seconds, the display will refresh with the last selected display mode setting. c Track title mode displays the title of the se-

lected CD track.

c Disc title mode displays the title of the CD

being played.

c Track number mode displays the number selected disc and the track that is currently being played on the disk.

c Disc number mode displays the current disc

c Folder title mode displays the folder name

number playing in the changer.

given to the MP3 folder.

MP3 display mode

To change the text displayed when listening to an MP3/WMA CD with MP3/WMA text (when CD with text is being used), press the DISP button. The DISP button will scroll through the CD text as follows: Track title ˆ! Folder title ˆ! Artist title ˆ! Disc number ˆ! Folder number. To change the default display mode, press the AUDIO knob repeatedly until DISPLAY MODE appears on the display, then rotate the knob to select the following display modes: Disc number ˆ! Folder number. Once a display mode is selected, press the AU- DIO knob again to store the setting. c Folder number mode displays the selected folder number and the track number that is currently being played.

c Disc number mode displays the selected disc number and the track number that is currently being played.

c Artist title mode displays the artist title of the

MP3/WMA file.

c Track title mode displays the track title of the

MP3/WMA file.

Display satellite radio display mode (if so equipped)

To change the text displayed when listening to satellite radio (if so equipped) press the DISP button. The DISP button will scroll through the broadcast information as follows: Name ˆ! Title ˆ! Current display mode. To change the default display mode press the AUDIO button to display mode and press the TUNE button to select the following display modes: Channel number ˆ! Channel name ˆ! Name ˆ! Title. Once the display mode is selected press the AUDIO button again to store the setting. If the AUDIO button is not pressed after 8 seconds the display will refresh with the last selected display mode setting. c Channel number mode displays the channel number of the selected satellite radio sta- tion.

c Channel name mode displays the channel name of the selected satellite radio station. c Name mode displays the name of the artist, host or weather condition of the selected satellite radio station.

Heater, air conditioner, audio and phone systems 4-21

Z REVIEW COPY—2008 08+ Truck/Frontier (fro) Owners Manual—USA_English (nna) 06/30/07—debbie X

c Title mode displays the song title, show name, or temperature of the selected satel- lite radio station.

FM/AM/SAT radio operation FM/AM/SAT band select:

Pushing the RADIO button will change the band as follows: AM ˆ! FM or SAT (satellite, if so equipped) When the RADIO button is pushed while the ignition switch is in the ACC or ON position, the radio will come on at the station last played.

The last station played will also come on when the POWER/VOLUME control knob is de- pressed to ON.

No satellite radio reception is available when the RADIO button is pressed to access satellite radio stations unless optional satellite receiver and an- tenna are installed and an XMT satellite radio service subscription is active. Satellite radio can only be installed in vehicles that were factory pre-wired for satellite radio. Satellite radio is not available in Alaska, Hawaii and Guam. If satellite radio is not operational then the RADIO button is used to toggle between AM and FM bands.

If a compact disc is playing when the RADIO button is pushed, the compact disc will automati- cally be turned off and the last radio station played will come on.

The FM stereo indicator ST will glow during FM stereo reception. When the stereo broadcast signal is weak, the radio will automatically change from stereo to monaural reception.

CAT FOLDER (tuning) button:

To manually tune the radio, press the CAT FOLDER button or turn the tun- ing knob to right or left.

or

To move quickly through the channels, press and hold either the button down for or more than 1.5 seconds.

SEEK/TRACK tuning button:

Press the SEEK/TRACK button for less than 1.5 seconds to tune from high to low or low to high frequencies and stop at the next broadcasting station.

or

To seek quickly through the channels, press and hold the SEEK/TRACK button for more than 1.5
seconds. When the button is released the radio will seek to the next broadcasting station.

SCAN RPT tuning (Type A, B and D only):

Press the SCAN RPT button for more than 1.5
seconds to stop at each broadcasting station (AM, FM or SAT if so equipped) for 5 seconds. Pressing the button again during this 5 second period will stop scan tuning and the radio will remain tuned to that station. If the SCAN RPT button is not pressed within 5 seconds, scan tuning moves to the next station. PRESET A•B•C (Station memory opera- tions):

18 stations can be set for the FM, AM and SAT (satellite, if so equipped) radio to the A, B and C preset button in any combination of FM, AM or SAT stations.

1. Choose preset bank A, B or C using the

PRESET A•B•C select button.

2. Select the desired FM, AM or SAT station

band.

3. Tune to the desired station using manual, SEEK or SCAN tuning. Press and hold any of the desired station memory buttons (1 (cid:150) 6) until a beep sound is heard.

4. The channel indicator will then come on and the sound will resume. Programming is now complete.

4-22 Heater, air conditioner, audio and phone systems

Z REVIEW COPY—2008 08+ Truck/Frontier (fro) Owners Manual—USA_English (nna) 06/30/07—debbie X

5. Other buttons can be set in the same man-

ner.

If the battery cable is disconnected, or if the fuse opens, the radio memory will be canceled. In that case, reset the desired stations. Radio data system (RDS):

RDS stands for Radio Data System, and is a data information service transmitted by some radio stations on the FM band (not AM band). Cur- rently, most RDS stations are in large cities, but many stations are now considering broadcasting RDS data.

RDS can display: c Station call sign, such as (cid:147)WHFR 98.3(cid:148). c Station name, such as (cid:147)The Groove(cid:148). c Music or programming type such as (cid:147)Clas-

sical(cid:148), (cid:147)Country(cid:148), or (cid:147)Rock(cid:148). c Artist and song information. If the station broadcasts RDS information, the RDS icon is displayed. Compact disc (CD) changer operation Turn the ignition key to the ACC or ON position and insert the compact disc into the slot with the label side facing up. The compact disc will be

guided automatically into the slot and start play- LOAD ing. To insert the disc, first press the button.

If the radio is already operating, it will automati- cally turn off and the compact disc will play.

If the system has been turned off while the com- pact disc was playing, pressing the PWR/VOL control knob will start the compact disc.

Do not use 3.1 in (8 cm) diameter compact discs in the CD changer.

LOAD button:

To insert a CD in the CD changer, press the load button for less than 1.5 seconds. Select the loading slot by pressing the CD insert select button (1 (cid:150) 6), then insert the CD.

To insert 6 CDs to the CD changer, press the load button for more than 1.5 seconds.

The slot numbers (1 (cid:150) 6) will illuminate on the display when CDs are loaded into the changer. CD button:

When the CD button is pressed with the system off and the compact disc loaded, the system will turn on and the compact disc will start to play.

When the CD button is pressed with the com- pact disc loaded with the radio playing, the radio will automatically be turned off and the compact disc will start to play.

SEEK/TRACK button:

button is pressed for less than When the 1.5 seconds while a compact disc is playing, the track being played returns to its beginning. Press several times to skip back through tracks. The compact disc will go back the number of times the button is pressed.

When the button is pressed for less than 1.5 seconds while the compact disc is playing, the next track will start to play from its beginning. Press several times to skip through tracks. The compact disc will advance the number of times the button is pressed. (When the last track on the compact disc is skipped through, the first track will be played.)

CAT FOLDER button:

While playing a CD, press the CAT FOLDER or to fast forward or rewind a button track on a CD.

Heater, air conditioner, audio and phone systems 4-23

Z REVIEW COPY—2008 08+ Truck/Frontier (fro) Owners Manual—USA_English (nna) 06/30/07—debbie X

MP3 CAT FOLDER button:

CD EJECT:

or

to fast forward or rewind a track on an

While playing an MP3 CD, press the CAT FOLDER button to scan back- ward or forward through available folders. Press and hold the CAT FOLDER button or MP3 CD. CD select buttons: To play another CD that has been loaded, press a CD select button (1 (cid:150) 6). SCAN/RPT: When the SCAN/RPT play button is pushed while the compact disc is played, the play pattern can be changed as follows: ALL DISC RPT ! 1 DISC RPT! 1 TRACK RPT ! ALL DISC RDM ! 1 DISC RDM ! ALL DISC RPT ALL DISC RPT: All discs loaded will be repeated. 1 DISC RPT: The disc that is currently playing will be repeated. 1 TRACK RPT: The track that is currently playing will be repeated ALL DISC RDM: Tracks from all discs will be played randomly 1 DISC RDM: Tracks from the disc that is cur- rently playing will be played randomly 4-24 Heater, air conditioner, audio and phone systems

Current/Selected disc: c Press the

button, then press the slot number (1 (cid:150) 6) for the desired disc. The compact disc will be ejected. If no slot num- ber (1 (cid:150) 6) is pressed, the current loaded disc will be ejected. Also, if the ejected disc is not removed within 15 seconds, the disc will reload.

All discs: c Press and hold the

button for more than 1.5 seconds. The compact discs will be ejected one by one. If a disc is not removed within 15 seconds, or the button is pressed again during the eject sequence, the entire disc eject sequence will be can- celed.

When this button is pressed while the compact disc is being played, the compact disc will eject and the last source will be played. CD IN indicator: The slot numbers (1 (cid:150) 6) will illuminate if CDs have been loaded into the changer in CD mode only.

LHA0733

AUX jack (if so equipped) The AUX jack s1 is located above the power outlet. The AUX audio input jack accepts any standard analog audio input such as from a por- table cassette tape player, MP3 player or a laptop computer. Press the AUX button to play a compatible device when it is plugged into the AUX jack.

Z REVIEW COPY—2008 08+ Truck/Frontier (fro) Owners Manual—USA_English (nna) 06/30/07—debbie X

LHA0049

LHA0269

LHA1087

Type A Volume control switch 1. 2. MODE select switch 3. 4.

POWER on/off switch Tuning switch

Type B Volume control switch Phone operation switch POWER on and MODE select switch Tuning switch

1. 2. 3. 4.

CD CARE AND CLEANING c Handle a CD by its edges. Do not bend the

disc. Never touch the surface of the disc.

c Always place the discs in the storage case

when they are not being used.

c To clean a disc, wipe the surface from the center to the outer edge using a clean, soft cloth. Do not wipe the disc using a circular motion.

c Do not use a conventional record cleaner or

alcohol intended for industrial use.

c A new disc may be rough on the inner and outer edges. Remove the rough edges by rubbing the inner and outer edges with the side of a pen or pencil as illustrated.

Heater, air conditioner, audio and phone systems 4-25

Z REVIEW COPY—2008 08+ Truck/Frontier (fro) Owners Manual—USA_English (nna) 06/30/07—debbie X

To install the antenna rod, turn the antenna clock- wise. Tighten the antenna rod to specification using a suitable tool such as an open-end wrench. The antenna rod tightening specification is 3.4 (cid:150) 3.6 N•m (30 (cid:150) 32 in-lb). Do not use pliers to tighten the antenna as they can leave marks on the antenna surface. The antenna rod cannot be hand tightened to the proper specification.

CAUTION

Always properly tighten the antenna rod during installation or the antenna rod may break during vehicle operation.

STEERING WHEEL SWITCH FOR AUDIO CONTROL The audio system can be operated using the controls on the steering wheel. POWER on/off switch With the ignition key turned to the ACC or ON position, push the POWER switch to turn the audio system on or off.

If you have the Type B switch, with the ignition key turned to the ACC or ON position, push the MODE switch to turn the audio system on. (cid:147)MODE(cid:148) select switch Push the mode select switch to change the modes: PRESET A ! PRESET B ! PRESET C ! CD* ! AUX** ! PRESET A *This mode is only available when a CD is loaded.

**This mode is only available when a compatible auxiliary device is plugged into the AUX jack. Volume control switch Push the volume control switch up or down to increase or decrease the volume.

Tuning

or

or

) for less

Memory change (radio): Push the tuning switch ( than 1.5 seconds to change presets. Seek tuning (radio): Push the tuning switch ( ) for more than 1.5 seconds to seek the next or previ- ous radio station. Next/Previous track (CD): Push the tuning switch for less than 1.5 seconds to return to the beginning of the present track or skip to the next track. Push several times to skip back or skip through tracks. Change disc (CD) (if so equipped): Push the SEEK tuning switch for or more than 1.5 seconds to change the playing disc up or down. ANTENNA The antenna cannot be shortened, but can be removed. When you need to remove the antenna, turn the antenna rod counterclockwise.

or

4-26 Heater, air conditioner, audio and phone systems

Z REVIEW COPY—2008 08+ Truck/Frontier (fro) Owners Manual—USA_English (nna) 06/30/07—debbie X

CAR PHONE OR CB RADIO

When installing a CB, ham radio or car phone in your NISSAN, be sure to observe the following precautions, otherwise the new equipment may adversely affect the engine control system and other electronic parts.

WARNING

c A cellular telephone should not be used while driving so full attention may be given to vehicle operation. Some juris- dictions prohibit the use of cellular tele- phones while driving.

c If you must make a call while your ve- hicle is in motion, the hands free cellu- lar phone operational mode (if so equipped) is highly recommended. Ex- ercise extreme caution at all times so full attention may be given to vehicle operation.

c If a conversation in a moving vehicle requires you to take notes, pull off the road to a safe location and stop your vehicle before doing so.

BLUETOOTHT HANDS-FREE PHONE SYSTEM (if so equipped)

CAUTION

WARNING

c Use a phone after stopping your vehicle in a safe location. If you have to use a phone while driving, exercise extreme caution at all times so full attention may be given to vehicle operation.

c If you are unable to devote full attention to vehicle operation while talking on the phone, pull off the road to a safe location and stop your vehicle.

CAUTION

To avoid discharging the vehicle battery, use a phone after starting the engine.

c Keep the antenna as far away as pos- control

sible from the electronic modules.

c Keep the antenna wire more than 8 in (20 cm) away from the electronic con- trol system harnesses. Do not route the antenna wire next to any harness.

c Adjust the antenna standing-wave ratio as recommended by the manufacturer. c Connect the ground wire from the CB

radio chassis to the body.

c For details, consult a NISSAN dealer. c Do not ground electrical accessories directly to the battery terminal. Doing so, will bypass the variable voltage con- trol system and the vehicle battery may not charge completely. Refer to (cid:147)Vari- able voltage control system(cid:148) in the (cid:147)Maintenance and do-it-yourself(cid:148) sec- tion later in this manual.

c Use electrical accessories with the en- gine running to avoid discharging the vehicle battery.

Heater, air conditioner, audio and phone systems 4-27

Z REVIEW COPY—2008 08+ Truck/Frontier (fro) Owners Manual—USA_English (nna) 06/30/07—debbie X

module when the ignition switch is turned to the ON position with the paired cellular phone turned on and carried in the vehicle. You can register up to 5 different BluetoothT cellular phones to the in-vehicle phone module. However, you can talk on only one cellular phone at a time. Before using the BluetoothT Hands-Free Phone System, refer to the following notes. c Set up the wireless connection between a cellular phone and the in-vehicle phone module before using the hands-free phone system.

c Some BluetoothT enabled cellular phones may not be recognized by the in-vehicle phone visit www.nissanusa.com/bluetooth for a recom- mended phone list and pairing.

module.

Please

c You will not be able to use a hands-free

phone under the following conditions: (cid:150) Your vehicle is outside of the cellular ser-

vice area.

(cid:150) Your vehicle is in an area where it is difficult to receive a cellular signal; such as in a tunnel, in an underground parking garage, near a tall building or in a moun- tainous area.

Your NISSAN is equipped with the BluetoothT Hands-Free Phone System. If you have an ap- proved BluetoothT enabled cellular phone, you can set up the wireless connection between your cellular phone and the in-vehicle phone module. With BluetoothT wireless technology, you can

LHA1085
make or receive a hands-free telephone call with your cellular phone in the vehicle.

Once your cellular phone is paired to the in- vehicle phone module, no other phone connect- ing procedure is required. Your phone is auto- matically connected with the in-vehicle phone

4-28 Heater, air conditioner, audio and phone systems

Z REVIEW COPY—2008 08+ Truck/Frontier (fro) Owners Manual—USA_English (nna) 06/30/07—debbie X

(cid:150) Your cellular phone is locked to prevent it

from being dialed.

c When the radio wave condition is not ideal or ambient sound is too loud, it may be difficult to hear the other person(cid:146)s voice dur- ing a call.

c Do not place the cellular phone in an area surrounded by metal or far away from the in-vehicle phone module to prevent tone quality degradation and wireless connection disruption.

c While a cellular phone is connected through the BluetoothT wireless connection, the bat- tery power of the cellular phone may dis- charge quicker than usual. The BluetoothT Hands-Free Phone System cannot charge cellular phones.

c If the hands-free phone system seems to be malfunctioning, see (cid:147)Troubleshooting guide(cid:148) later in this section. You can also visit www.nissanusa.com/bluetooth for trouble- shooting help.

c Some cellular phones or other devices may cause interference or a buzzing noise to come from the audio system speakers. Stor- ing the device in a different location may reduce or eliminate the noise.

c Refer to the cellular phone Owner(cid:146)s Manual regarding the telephone charges, cellular phone antenna and body, etc.

This device complies with Part 15 of the FCC Rules. Operation is subject to the fol- lowing two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference re- ceived, including interference that may cause undesired operation.

FCC Radiation Exposure Statement:

This equipment complies with FCC radiation ex- posure limits set forth for an uncontrolled envi- ronment. This equipment should be installed and operated with minimum distance of 8 inches (20
cm) between the radiator and your body. This Transmitter must not be co-located or operating in conjunction with any other antenna or transmit- ter. USING THE SYSTEM The NISSAN Voice Recognition system allows hands-free operation of the BluetoothT Phone System.

If the vehicle is in motion, some commands may not be available so full attention may be given to vehicle operation.

Initialization When the ignition switch is turned to the ON position, NISSAN Voice Recognition is initialized, which takes a few seconds. When completed, the amber light on the overhead console illumi- nates and the system is ready to accept voice commands. If the button is pressed before the initialization completes, the system will an- nounce (cid:147)Hands-free phone system not ready(cid:148) and will not react to voice commands. Operating tips To get the best performance out of the NISSAN Voice Recognition system, observe the following: c Keep the interior of the vehicle as quiet as possible. Close the windows to eliminate surrounding noises (traffic noises, vibration sounds, etc.), which may prevent the system from recognizing voice commands correctly. c Wait until the tone sounds before speaking a command. Otherwise, the command will not be received properly.

c Start speaking a command within 5 seconds

after the tone sounds.

c Speak in a natural voice without pausing

between words.

Heater, air conditioner, audio and phone systems 4-29

Z REVIEW COPY—2008 08+ Truck/Frontier (fro) Owners Manual—USA_English (nna) 06/30/07—debbie X

Giving voice commands To operate NISSAN Voice Recognition, press and release the button located on the steering wheel. The light on the overhead con- sole flashes to signal you have entered a voice recognition (VR) session. After the tone sounds, speak a command. The command given is picked up by the micro- phone, and voice feedback is given when the command is accepted. c If you need to hear the available commands for the current menu again, say (cid:147)Help(cid:148) and the system will repeat them.

c If a command is not recognized, the system announces, recognized. Please try again.(cid:148) Repeat the command in a clear voice.

(cid:147)Command not

c If you want to go back to the previous com- mand, you can say (cid:147)Go back(cid:148) or (cid:147)Correc- tion(cid:148) any time the system is waiting for a response.

c You can cancel a command when the sys- tem is waiting for a response by saying, (cid:147)Cancel(cid:148) or (cid:147)Quit.(cid:148) The system announces (cid:147)Cancel(cid:148) and ends the VR session. You can also press the button on the steering wheel at any time. Whenever the VR session is cancelled, a double beep is played to indicate you have exited the system.

c If you want to adjust the volume of the voice feedback, press the volume control switches (+ or -) on the steering wheel while being provided with feedback. You can also use the radio volume control knob.

c In most cases you can interrupt the voice feedback to speak the next command by pressing the button on the steering wheel.

c To speed the operation you can say multiple

commands. For example, press the button then say (cid:147)Phonebook, New entry(cid:148) rather than (cid:147)Phonebook.(cid:148) Wait for the voice feedback prompt then say (cid:147)New entry(cid:148).

How to say numbers

NISSAN Voice Recognition requires a certain way to speak numbers in voice commands. Refer to the following rules and examples. c Either (cid:147)zero(cid:148) or (cid:147)oh(cid:148) can be used for (cid:147)0(cid:148).

4-30 Heater, air conditioner, audio and phone systems

Example: 1-800-662-6200
(cid:150) (cid:147)One eight oh oh six six two six two oh

oh(cid:148), or

(cid:150) (cid:147)One eight zero zero six six two six two oh

oh(cid:148)

c Words can be used for the first 4 digits

places only. Example: 1-800-662-6200
(cid:150) (cid:147)One eight hundred six six two six two oh

oh(cid:148),

(cid:150) NOT (cid:147)One eight hundred six six two sixty

two hundred, and

(cid:150) NOT (cid:147)One eight oh oh six six two sixty two

hundred.

c Numbers can be spoken in small groups. The system will prompt you to continue en- tering digits, if desired. Example: 1-800-662-6200
(cid:150) (cid:147)One eight oh oh(cid:148) The system repeats the numbers and prompts you to enter more. (cid:150) (cid:147)six six two(cid:148)

Z REVIEW COPY—2008 08+ Truck/Frontier (fro) Owners Manual—USA_English (nna) 06/30/07—debbie X

The system repeats the numbers and prompts you to enter more. (cid:150) (cid:147)six two oh oh(cid:148)

c You can say (cid:147)Star(cid:148) for * and (cid:147)Pound(cid:148) for # at any time in any position of the phone num- ber. Example: 1-555-1212 *123
(cid:150) (cid:147)One five five five one two one two star

one two three(cid:148)

NOTE: For best results, say phone numbers as single digits.

LHA1086

CONTROL BUTTONS The control buttons for the BluetoothT Hands- Free Phone System are located on the steering wheel.

PHONE/SEND Press the session or answer an incoming call.

button to initiate a VR

You can also use the button to skip through system feedback and to enter commands during a call. See (cid:147)List of voice commands(cid:148) and (cid:147)During a call(cid:148) later in this section for more information.

PHONE/END Press the session or end a call.

button to cancel a VR

GETTING STARTED The following procedures will help you get started using the BluetoothT Hands-Free Phone System with NISSAN Voice Recognition. For ad- ditional command options, refer to (cid:147)List of voice commands(cid:148) later in this section. Choosing a language You can interact with the BluetoothT Hands-Free Phone System using English, Spanish or French. To change the language, perform the following. 1. Press and hold the button for more

than 5 seconds.

2. The

system announces:

the (cid:147)Press PHONE/SEND ( the ) button for hands-free phone system to enter the speaker adaptation mode or press the PHONE/END ( ) button to select a dif- ferent language.(cid:148)

3. Press the

button.

For information on speaker adaptation, see (cid:147)Speaker adaptation (SA) mode(cid:148) later in this section.

Heater, air conditioner, audio and phone systems 4-31

Z REVIEW COPY—2008 08+ Truck/Frontier (fro) Owners Manual—USA_English (nna) 06/30/07—debbie X

4. The system announces the current language and gives you the option to change the lan- guage to Spanish (in Spanish) or French (in French). Use the following chart to select the language.

NOTE: You must press the the change the language.

button or button within 5 seconds to

Current language

English Spanish French

Press

(PHONE/SEND)

Press (PHONE/END)

to select Spanish English English

to select French French Spanish

5.

If you decide not to change the language, do not press either button. After 5 seconds, the VR session will end, and the language will not be changed.

Pairing procedure

NOTE:

The pairing procedure must be performed when the vehicle is stationary. If the vehicle starts moving during the procedure, the procedure will be cancelled.

Main Menu (cid:147)Setup(cid:148) sA

(cid:147)Pair phone(cid:148) sB

(cid:147)New phone(cid:148) sC

Initiate from handset sD

Name phone sE

Assign priority sF

Choose ringtone sG

1. Press the

button on the steering wheel. The system announces the available commands.

2. Say: (cid:147)Setup(cid:148) sA . The system acknowledges the command and announces the next set of available commands.

3. Say: (cid:147)Pair phone(cid:148) sB . The system acknowl- edges the command and announces the next set of available commands.

4. Say: (cid:147)New phone(cid:148) sC . The system acknowl- edges the command and asks you to initiate pairing from the phone handset sD . The pairing procedure of the cellular phone varies according to each cellular phone model. See the cellular phone Owner(cid:146)s Manual for details. You can also visit www.nissanusa.com/bluetooth for instruc- tions on pairing NISSAN recommended cel- lular phones.

When prompted for a Passkey code, enter (cid:147)1234(cid:148) from the handset. The Passkey code (cid:147)1234(cid:148) has been assigned by NISSAN and cannot be changed.

5. The system asks you to say a name for the

phone sE . If the name is too long or too short, the system tells you, then prompts you for a name again.

Also, if more than one phone is paired and the name sounds too much like a name already used, the system tells you, then prompts you for a name again.

4-32 Heater, air conditioner, audio and phone systems

Z REVIEW COPY—2008 08+ Truck/Frontier (fro) Owners Manual—USA_English (nna) 06/30/07—debbie X

6. The system asks you to assign a priority level sF . The priority level determines which phone is active when more than one paired BluetoothT phone is in the vehicle. Follow the instructions provided by the system or refer to (cid:147)Setup(cid:148) later in this section for more information on changing priorities.

7. The system will ask if you would like to select a custom ring tone sG . Follow the instruc- tions provided by the system or refer to (cid:147)Setup(cid:148) later in this section for more infor- mation on selecting ringtones.

Making a call by entering a phone number

Main Menu (cid:147)Call(cid:148) sA

Number (speak digits) sB

(cid:147)Dial(cid:148) sC

1. Press the

button on steering wheel. A

tone will sound.

2. Say: (cid:147)Call(cid:148) sA . The system acknowledges the command and announces the next set of available commands.

3. Say the number you wish to call sB . For example, 555-1212 can be said as (cid:147)five five five one two one two.(cid:148) See (cid:147)How to say numbers(cid:148) earlier in this section for more information.

4. When you have finished speaking the phone number, the system repeats it back and an- nounces the available commands.

5. Say: (cid:147)Dial(cid:148) sC . The system acknowledges

the command and makes the call.

For additional command options, see (cid:147)List of voice commands(cid:148) later in this section. Receiving a call When you hear the ring tone, press the button on the steering wheel. Once the call has ended, press the on the steering wheel.

button

NOTE: If you do not wish to take the call when you hear the ring tone, press the button on the steering wheel. For additional command options, see (cid:147)List of voice commands(cid:148) later in this section.

LIST OF VOICE COMMANDS

Main Menu

(cid:147)Call(cid:148) (cid:147)Phone Book(cid:148) (cid:147)Memo Pad(cid:148) (cid:147)Setup(cid:148)

When you press and release the button on the steering wheel, you can choose from the commands on the Main Menu. The following pages describe these commands and the com- mands in each sub-menu. Remember to wait for the tone before speaking. You can say (cid:147)Help(cid:148) to hear the list of commands currently available any time the system is waiting for a response. If you want to end an action without completing it, you can say (cid:147)Cancel(cid:148) or (cid:147)Quit(cid:148) at any time the system is waiting for a response. The system will end the VR session. Whenever the VR session is cancelled, a double beep is played to indicate you have exited the system. If you want to go back to the previous command, you can say (cid:147)Go back(cid:148) or (cid:147)Correction(cid:148) any time the system is waiting for a response.

Heater, air conditioner, audio and phone systems 4-33

Z REVIEW COPY—2008 08+ Truck/Frontier (fro) Owners Manual—USA_English (nna) 06/30/07—debbie X

When you get used to the menus in the system, you can talk ahead by saying more than one command at a time. For example, say, (cid:147)Call five five five one two one two(cid:148) or (cid:147)Memo pad record.(cid:148)

Also, when you get used to the system re- sponses, you can skip ahead to the tone by pressing the button on the steering wheel. However, if you press the button when the system is waiting for a response from you it will end the VR session. (cid:147)Call(cid:148)

Main Menu

(cid:147)Call(cid:148)

Name (speak name) sA Number (speak digits) sB (cid:147)Redial(cid:148) sC (cid:147)Call Back(cid:148) sD

Name (speak name) sA If you have stored entries in the Phone Book, you can dial a number associated with a name and location.

See (cid:147)Phone book(cid:148) later in this section to learn how to store entries.

When prompted by the system, say the name of the phone book entry you wish to call. The system acknowledges the name.

If there are multiple locations associated with the name, the system asks you to choose the loca- tion.

Once you have confirmed the name and location, the system begins the call. Number (speak digits) sB When prompted by the system, say the number you wish to call. Refer to (cid:147)How to say numbers(cid:148) and (cid:147)Making a call by entering a phone number(cid:148) earlier in this section for more details. (cid:147)Redial(cid:148) sC Use the Redial command to call the last number that was dialed within the vehicle.

NOTE:

The system will not redial the last number dialed by the handset keypad.

The system acknowledges the command, re- peats the number and begins dialing.

If a redial number does not exist, the system announces, (cid:147)There is no number to redial(cid:148) and ends the VR session.

4-34 Heater, air conditioner, audio and phone systems

(cid:147)Call back(cid:148) sD Use the Call Back command to dial the number of the last incoming call within the vehicle.

The system acknowledges the command, re- peats the number and begins dialing. If a call back number does not exist, the system announces, (cid:147)There is no number to call back(cid:148) and ends the VR session. During a call During a call there are several command options available. Press the button on the steering wheel to mute the receiving voice and enter com- mands. c (cid:147)Help(cid:148) (cid:151) The system announces the avail-

able commands.

c (cid:147)Go back/Correction(cid:148) (cid:151) The system an- nounces (cid:147)Go back,(cid:148) ends the VR session and returns to the call.

c (cid:147)Cancel/Quit(cid:148) (cid:151) The system announces (cid:147)Cancel,(cid:148) ends the VR session and returns to the call.

c (cid:147)Send/Enter/Call/Dial(cid:148) (cid:151) Use the Send command to enter numbers during a call. For example, if you were directed to dial an ex- tension by an automated system: Say: (cid:147)Send one two three four.(cid:148)

Z REVIEW COPY—2008 08+ Truck/Frontier (fro) Owners Manual—USA_English (nna) 06/30/07—debbie X

The system acknowledges the command and sends the tones associated with the numbers. The system then ends the VR ses- sion and returns to the call.

c (cid:147)Transfer call(cid:148) (cid:151) Use the Transfer Call com- mand to transfer the call from the BluetoothT Hands-Free Phone System to the cellular phone when privacy is desired. The system announces, (cid:147)Transfer call. Call transferred to privacy mode.(cid:148) The system then ends the VR session. You can also issue the Transfer Call com- mand again to return to a hands-free call through the vehicle.

c (cid:147)Mute(cid:148) (cid:151) Use the Mute command to mute your voice so the other party cannot hear it. Use the mute command again to unmute your voice.

NOTE: If a call is ended or the cellular phone network connection is lost while the Mute feature is on, the Mute feature will be reset to (cid:147)off(cid:148) for the next call so the other party can hear your voice.

(cid:147)Phone book(cid:148)

NOTE:

Phone book commands are not available when the vehicle is moving.

Main Menu

(cid:147)Phone Book(cid:148)