2004 Nissan Frontier Owners Manual

Do not use for extended periods of time with the engine stopped. This could result in a discharged battery.

Instruments and controls 2-35

Z REVIEW COPY—2004 Truck/Frontier (d22) Owners Manual (owners)—USA_English (nna) 06/08/04—debbie X

MEMO

2-36 Instruments and controls

3 Pre-driving checks and adjustments

Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2
Doors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2
Locking with key. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2
Locking with inside lock knob . . . . . . . . . . . . . . . . . . . . 3-3
Locking with power door lock switch (if so equipped) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3
Child safety rear door lock (Crew Cab models only) . . . . . . . . . . . . . . . . . . . . . . . . 3-4
Remote keyless entry system (if so equipped). . . . . . . . . 3-4
How to use remote keyless entry system . . . . . . . . . . 3-5
Battery replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-8
Hood . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-9
Tubular step rail (if so equipped) . . . . . . . . . . . . . . . . . . . 3-10
Fuel filler lid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-11

Fuel filler cap. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-11
Steering wheel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-12
Tilt operation (if so equipped) . . . . . . . . . . . . . . . . . . . 3-12
Sun visors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-13
Vanity mirror (if so equipped). . . . . . . . . . . . . . . . . . . . 3-13
Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-13
Inside mirror . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-13
Outside mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-13
Outside mirror remote control (if so equipped) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-14
Truck box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-15
Tailgate. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-15
Tie down hooks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-17

Z REVIEW COPY—2004 Truck/Frontier (d22) Owners Manual (owners)—USA_English (nna) 05/25/04—arosenma X

KEYS

DOORS

WARNING

c Always have the doors locked while driving. Along with the use of seat belts, this provides greater safety in the event of an accident by helping to prevent persons from being thrown from the vehicle. This also helps keep children and others from unintentionally open- ing the doors, and will help keep out intruders.

c Before opening any door, always look

for and avoid oncoming traffic.

c Do not leave children unattended inside the vehicle. They could unknowingly ac- tivate switches or controls. Unattended children could become involved in seri- ous accidents.

WPD0153

Driver(cid:146)s side

LOCKING WITH KEY Manual To lock either the driver or passenger side door, turn the key toward the front of the vehicle s1 . To unlock, turn it toward the rear s2 .

WPD0152

1.

Two master keys (black) with chrome NISSAN brand symbol on one side Key number plate

2. A key number plate is supplied with your keys. Record the key number and keep it in a safe place (such as your wallet), not in the vehicle. If you lose your keys, see a NISSAN dealer for duplicates by using the key number. NISSAN does not record key numbers so it is very important to keep track of your key number plate. A key number is only necessary when you have lost all keys and do not have 1 to duplicate from. If you still have a key, this key can be duplicated by a NISSAN dealer or locksmith.

3-2 Pre-driving checks and adjustments

Z REVIEW COPY—2004 Truck/Frontier (d22) Owners Manual (owners)—USA_English (nna) 05/25/04—arosenma X

WPD0154

WPD0155

WPD0156

Inside lock

LOCKING WITH INSIDE LOCK KNOB To lock the door without the key, move the inside lock knob to the lock position s1 , then close the door. To unlock the door without the key, move the inside lock knob to the unlock position s2 .

Driver(cid:146)s side

Power (if so equipped) If your vehicle is equipped with the vehicle security system, the power door lock system allows you to lock or unlock all doors at the same time. Turning the key toward the front s1 of the vehicle locks all doors. Turning the key one time toward the rear s2 of the vehicle unlocks that door. From that position, returning the key to neutral s3 (where the key can only be removed and inserted) and turning it toward the rear again s4 within 5 seconds un- locks all doors.

Driver(cid:146)s side

LOCKING WITH POWER DOOR LOCK SWITCH (if so equipped) To lock all the doors without a key, push the door lock switch (driver(cid:146)s or front passenger(cid:146)s side) to the lock position s1 . When locking the door this way, be certain not to leave the key inside the vehicle.

To unlock all the doors without a key, push the door lock switch (driver(cid:146)s or front passenger(cid:146)s side) to the unlock position s2 .

Pre-driving checks and adjustments 3-3

Z REVIEW COPY—2004 Truck/Frontier (d22) Owners Manual (owners)—USA_English (nna) 05/25/04—arosenma X

Lockout protection When the power door lock switch (driver(cid:146)s or front passenger(cid:146)s side) is moved to the lock position with the key in the ignition and any door open, all doors will lock and unlock automatically. This helps to prevent the keys from being acci- dently locked inside the vehicle.

3-4 Pre-driving checks and adjustments

WPD0037
CHILD SAFETY REAR DOOR LOCK (Crew Cab models only) Child safety locks help prevent the rear doors from being opened accidentally, especially when small children are in the vehicle. The child safety lock levers are located on the edge of the rear doors. When the lever is in the lock position, the door can be opened only from the outside.

REMOTE KEYLESS ENTRY SYSTEM (if so equipped)

It is possible to lock/unlock all doors, turn the interior light on, and activate the panic alarm by using the keyfob from outside the vehicle. Be sure to remove the key from the vehicle before locking the doors.

The keyfob can operate at a distance of approxi- mately 33 ft (10 m) from the vehicle. The effective distance depends on the conditions around the vehicle.

As many as 4 keyfobs can be used with one vehicle. For information concerning the purchase and use of additional keyfobs, contact a NISSAN dealer.

The keyfob will not function when: c the battery is discharged c the distance between the vehicle and the

keyfob is over 33 ft (10 m)

CAUTION

Listed below are conditions or occur- rences which will damage the keyfob: c Do not allow the keyfob to become wet. c Do not drop the keyfob. c Do not strike the keyfob sharply against

another object.

Z REVIEW COPY—2004 Truck/Frontier (d22) Owners Manual (owners)—USA_English (nna) 05/25/04—arosenma X

c Do not place the keyfob for an extended period in an area where temperatures exceed 140(cid:176)F (60(cid:176)C).

twice and the horn beeps once as a re- minder that the doors are already locked. The horn may or may not beep once. Refer to (cid:147)Silencing the horn beep feature(cid:148) later in this section for details. c If a door

is open and you push button, the doors will lock the but the horn will not beep and the hazard lights will not flash.

WPD0157

HOW TO USE REMOTE KEYLESS ENTRY SYSTEM Locking doors 1. Close all windows. 2. Remove the key from the ignition switch. 3. Close the hood and all doors. 4. Push the

button on the keyfob. All the doors lock. The hazard lights flash twice and the horn beeps once to indicate all doors are locked. c When the

button is pushed with all doors locked, the hazard lights flash

Pre-driving checks and adjustments 3-5

Z REVIEW COPY—2004 Truck/Frontier (d22) Owners Manual (owners)—USA_English (nna) 05/25/04—arosenma X

WPD0158

button on the keyfob once.

Unlocking doors Push the c Only the driver(cid:146)s door unlocks. c The interior lights illuminate for 30 seconds when the interior light switch is in the normal operation position.

button on the keyfob again with 5

Push the seconds. c All doors unlock. The interior lights can be turned off without wait- ing 30 seconds by inserting the key into the ignition and turning to the ON or START position, 3-6 Pre-driving checks and adjustments

locking the doors with the keyfob or pushing the interior light switch to the OFF position. Auto relock When the button on the keyfob is pushed, all doors will lock automatically within 5 minutes unless one of the following operations is per- formed: c Any door is opened. c A key is inserted into the ignition switch and

the key is turned from OFF to ON.

WPD0159

Using the panic alarm If you are near your vehicle and feel threatened, you may activate the panic alarm to call attention by pushing and holding the button on the keyfob for longer than 0.5 second. The panic alarm and headlights will stay on for about 30 seconds. The panic alarm stops when: c it has run for about 30 seconds, or c the

button is pushed on

or

the keyfob.

Z REVIEW COPY—2004 Truck/Frontier (d22) Owners Manual (owners)—USA_English (nna) 05/25/04—arosenma X

Deactivating the horn beep feature does not si- lence the horn if the alarm is triggered.

WIC0325

buttons for at least 2 seconds.

Silencing the horn beep feature If desired, the horn beep feature can be deacti- vated using the keyfob. To deactivate: Press and hold the and The hazard lights will flash three times to confirm that the horn beep feature has been deactivated. To activate: Press and hold the and once more. The hazard lights will flash once and the horn will sound once to confirm that the horn beep feature has been reactivated.

buttons for at least 2 seconds

Pre-driving checks and adjustments 3-7

Z REVIEW COPY—2004 Truck/Frontier (d22) Owners Manual (owners)—USA_English (nna) 05/25/04—arosenma X

5. Press the

button, then the

button two or three times to check the key- fob operation.

If the battery is removed for any reason other than replacement, perform step 5. c An improperly disposed battery can hurt the environment. Always confirm local regulations for battery disposal. c The keyfob is water-resistant; how- ever, if it does get wet, immediately wipe completely dry.

c The operational range of the keyfob extends to approximately 33 ft (10 m) from the vehicle. This range may vary with conditions.

FCC Notice: Changes or modifications not expressly ap- proved by the manufacturer for compliance could void the user(cid:146)s authority to operate the equipment. This device complies with Part 15 of the FCC Rules and RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, in- cluding interference that may cause undes- ired operation of the device.

BATTERY REPLACEMENT Replace the battery in the keyfob as follows: s1 Open the lid using a coin. s2 Remove the battery.

3-8 Pre-driving checks and adjustments

s3

WPD0160
Install a new battery with the (cid:147)+(cid:148) facing down.

Recommended battery: Toshiba CR2025 or equivalent. s4 Close the lid securely.

Z REVIEW COPY—2004 Truck/Frontier (d22) Owners Manual (owners)—USA_English (nna) 05/25/04—arosenma X

HOOD

WARNING

c Make sure the hood is completely closed and latched before driving. Fail- ure to do so could cause the hood to fly open and result in an accident.

c If you see steam or smoke coming from the engine compartment, to avoid injury do not open the hood.

1. Pull the hood lock release handle sA located below the driver side instrument panel; the hood springs up slightly.

WPD0172
2. Lift the lever sB at the front of the hood with

your fingertips and raise the hood.

3. Remove the support rod from the clamp.

4.

Insert the support rod sC into the slot in the front edge of the hood.

5. When closing the hood, return the support rod to its original position, lower the hood to approximately 12 inches above the latch and release it. This allows proper engagement of the hood latch.

Pre-driving checks and adjustments 3-9

Z REVIEW COPY—2004 Truck/Frontier (d22) Owners Manual (owners)—USA_English (nna) 05/25/04—arosenma X

TUBULAR STEP RAIL (if so equipped)

Tubular step rail Front passenger step Rear passenger step

1. 2. 3. The tubular step rail has a front and rear step for assisting passengers getting into and out of the vehicle.

3-10 Pre-driving checks and adjustments

WPD0173

Z REVIEW COPY—2004 Truck/Frontier (d22) Owners Manual (owners)—USA_English (nna) 05/25/04—arosenma X

FUEL FILLER LID

WPD0276

WPD0277

FUEL FILLER CAP The fuel filler cap is a ratcheting type. Turn the cap counterclockwise to remove. To tighten, turn the cap clockwise until ratcheting clicks are heard.

Put the fuel filler cap in the cap holder while fueling.

WARNING

c Gasoline is extremely flammable and highly explosive under certain condi- tions. You could be burned or seriously injured if it is misused or mishandled. Always stop the engine and do not smoke or allow open flames or sparks near the vehicle when refueling.

c Fuel may be under pressure. Turn the cap a third of a turn, and wait for any (cid:147)hissing(cid:148) sound to stop to prevent fuel from spraying out and possibly causing personal injury. Then remove the cap.

c Do not attempt to top off the fuel tank after the fuel pump nozzle shuts off automatically. Continued refueling may cause fuel overflow, resulting in fuel spray and possibly a fire.

c Use only an original equipment type fuel filler cap as a replacement. It has a built-in safety valve needed for proper operation of the fuel system and emis- sion control system. An incorrect cap can result in a serious malfunction and possible injury. It could also cause the malfunction indicator lamp to come on. c Never pour fuel into the throttle body to

attempt to start your vehicle.

c Do not fill a portable fuel container on a truck bed liner, rubber truck bed mad, or other insulating material. Static elec- tricity can cause an explosion of flam- mable liquid, vapor or gas in any vehicle or trailer. To reduce the risk of serious injury or death when filling portable fuel containers: (cid:150) Always place the container on the

ground when filling.

(cid:150) Do not use electronic devices when

filling.

Pre-driving checks and adjustments 3-11

Z REVIEW COPY—2004 Truck/Frontier (d22) Owners Manual (owners)—USA_English (nna) 05/25/04—arosenma X

STEERING WHEEL

c For additional

information, see the (cid:147)Malfunction indicator lamp (MIL)(cid:148) in the (cid:147)Instruments and Controls(cid:148) section earlier in this manual.

(cid:150) Keep the pump nozzle in contact with the container while you are fill- ing it.

(cid:150) Use only approved portable fuel con-

tainers for flammable liquid.

CAUTION

c If fuel is spilled on the vehicle body, flush it away with water to avoid paint damage.

c Tighten until the fuel filler cap clicks. Failure to tighten the fuel filler cap properly may cause the mal- function indicator lamp (MIL) to illumi- nate. If the lamp illuminates be- cause the fuel filler cap is loose or missing, tighten or install the cap and to continue vehicle. The lamp should turn off after a

drive

the

few driving trips. If the lamp does not turn off after a few driving trips, have the vehicle inspected by a NISSAN dealer.

3-12 Pre-driving checks and adjustments

WPD0167

TILT OPERATION (if so equipped) Pull the lock lever down and adjust the steering wheel up or down to the desired position. Push the lock lever up firmly to lock the steering wheel in place.

WARNING

Do not adjust the steering wheel while driving. You could lose control of your vehicle and cause an accident.

Z REVIEW COPY—2004 Truck/Frontier (d22) Owners Manual (owners)—USA_English (nna) 05/25/04—arosenma X

SUN VISORS

MIRRORS

WPD0168

WPD0126

VANITY MIRROR (if so equipped) A vanity mirror is located on the rear side of the passenger sun visor.

INSIDE MIRROR The night position s1 reduces glare from the headlights of vehicles behind you at night. Use the day position s2 when driving in daylight hours.

WARNING

Use the night position only when neces- sary, because it reduces rear view clarity.

WPD0169

Type A OUTSIDE MIRRORS The outside mirrors can be moved in any direc- tion for a better rear view. Type A: Adjust to the desired position by moving the entire mirror assembly. Type B: Adjust to the desired position by press- ing directly on the mirror surface.

Pre-driving checks and adjustments 3-13

Z REVIEW COPY—2004 Truck/Frontier (d22) Owners Manual (owners)—USA_English (nna) 05/25/04—arosenma X

WPD0170

Type B

WPD0056

WPD0274

Foldable outside mirrors Push the mirrors backward to fold them.

OUTSIDE MIRROR REMOTE CONTROL (if so equipped) The outside mirror remote control only operates when the ignition switch is in the ACC or ON position.

Rotate the control lever to select the right or left mirror. Adjust the mirror to the desired position by moving the control lever.

3-14 Pre-driving checks and adjustments

Z REVIEW COPY—2004 Truck/Frontier (d22) Owners Manual (owners)—USA_English (nna) 05/25/04—arosenma X

TRUCK BOX

WARNING

c Objects viewed in the outside mirror on the passenger side are closer than they appear. Be careful when moving to the right. Using only this mirror could cause an accident. Use the inside mirror or glance over your shoulder to properly judge distances to other objects.

c Do not adjust the mirrors while driving. You could lose control of your vehicle and cause an accident.

WPD0175

TAILGATE Opening the tailgate Pull the tailgate handle upward and lower the tailgate. The support cables hold the tailgate open. When closing the tailgate, make sure the latches are securely locked.

WPD0176
To open the tailgate to the lowest position, lift the tailgate to a 45 degree angle, then release the support cables. Do not drive the vehicle with the tailgate down, unless equipped with Nissan(cid:146)s Bed Extender (accessory) in the deployed posi- tion.

For proper truck box loading see (cid:147)Loading tips(cid:148) under the (cid:147)Vehicle loading information(cid:148) heading in the (cid:147)Technical and consumer information(cid:148) sec- tion of this manual.

Pre-driving checks and adjustments 3-15

Z REVIEW COPY—2004 Truck/Frontier (d22) Owners Manual (owners)—USA_English (nna) 05/25/04—arosenma X

Installing the tailgate 1. 2. Hold the tailgate at a 45 degree angle and

Insert the tailgate into the right side hinge.

insert into the left side hinge.

3. Continue to hold the tailgate at a 45 degree angle and attach the tailgate support cables.

4. Close the tailgate securely.

WARNING

c It is extremely dangerous to ride in a cargo area inside a vehicle. In a colli- sion, people riding in these areas are more likely to be seriously injured or killed.

c Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts.

c Be sure everyone in your vehicle is in a

seat and using a seat belt properly.

3-16 Pre-driving checks and adjustments

IC0175

Removing the tailgate 1. Release the tailgate support cables.

2. Hold the tailgate at a 45 degree angle.

3. Pull the tailgate out from the left side hinge.

4. Remove the tailgate from the right side

hinge.

CAUTION

The tailgate is heavy. Be careful not to drop it during removal.

Z REVIEW COPY—2004 Truck/Frontier (d22) Owners Manual (owners)—USA_English (nna) 05/25/04—arosenma X

WARNING

c Properly secure all cargo with ropes or straps to help prevent it from sliding or shifting. In a sudden stop or collision, unsecured cargo could cause personal injury.

WPD0275

WPD0178

Locking the tailgate To lock the tailgate, turn the key toward the pas- senger side of the vehicle s1 . To unlock, turn the key toward the driver side s2 .

TIE DOWN HOOKS For your convenience, tie down hooks are placed at each corner of the truck box. These may be used to help secure cargo loaded into the truck box. c The weight of the cargo load must be evenly distributed over both the front and the rear axles.

c All cargo should be securely fastened with ropes or straps to prevent it from shifting or sliding within the vehicle.

Pre-driving checks and adjustments 3-17

Z REVIEW COPY—2004 Truck/Frontier (d22) Owners Manual (owners)—USA_English (nna) 05/25/04—arosenma X

MEMO

3-18 Pre-driving checks and adjustments

4 Heater, air conditioner and audio systems

Ventilators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2
Heater and air conditioner (manual). . . . . . . . . . . . . . . . . . 4-2
Controls. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3
Heater operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4
Air conditioner operation (if so equipped) . . . . . . . . . 4-5
Airflow charts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-6
Servicing air conditioner. . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-9
Audio system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-10
Radio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-10
FM radio reception . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-10
AM radio reception . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-10

Audio operation precautions . . . . . . . . . . . . . . . . . . . . 4-11
FM-AM radio with compact disc (CD) player (if so equipped) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-12
FM-AM radio with compact disc (CD) changer (if so equipped) . . . . . . . . . . . . . . . . . . . . . . . 4-16
CD care and cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . 4-27
Steering wheel switch for audio control (if so equipped) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-28
Antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-28
Car phone or CB radio . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-29

Z REVIEW COPY—2004 Truck/Frontier (d22) Owners Manual (owners)—USA_English (nna) 05/25/04—arosenma X

VENTILATORS

Adjust air flow direction for the driver side s1 , center s2 , and passenger side s3 ventilators by moving the ventilator slide and/or ventilator as- semblies.

WHA0223

HEATER AND AIR CONDITIONER (manual)

WARNING

c The air conditioner cooling function op- erates only when the engine is running. c On hot, sunny days, temperatures in a closed vehicle could quickly become high enough to cause severe or possi- bly fatal injuries to people or animals. Do not leave children or adults who would normally require the support of others in your vehicle. Unattended pets should not be left alone either.

c Do not use the recirculation mode for long periods as it may cause the interior air to become stale and the windows to fog up.

c Positioning of the heater and/or air conditioner controls should not be done while driving so full attention may be given to vehicle operation.

4-2 Heater, air conditioner and audio systems

Z REVIEW COPY—2004 Truck/Frontier (d22) Owners Manual (owners)—USA_English (nna) 05/25/04—arosenma X

WHA0235

1. 2. 3.

Fan control dial Temperature control dial Rear window defroster switch (if so equipped) Air flow control dial Air conditioner button (if so equipped) Air recirculation button (if so equipped)

4. 5. 6. CONTROLS Fan control dial The fan control dial turns the fan on and off, and controls fan speed.

Air flow control dial The air flow control dial allows you to select the air flow outlets.

(cid:151) Air flows from center and side

ventilators.

(cid:151) Air flows from center and side

ventilators and the front and rear floor outlets.

(cid:151) Air flows mainly from the front and

rear floor outlets.

(cid:151) Air flows from defroster outlets

and the front and rear floor outlets.

(cid:151) Air flows mainly from defroster

outlets.

The air flow control dial also has intermediate positions which allow the air flow to be distrib- uted between 2 of the icon positions on the air flow control dial. Temperature control dial The temperature control dial allows you to adjust the temperature of the outlet air. To make the temperature more cool turn the dial more to the left to make the temperature more warm turn the dial more to the right.

Air recirculation button (if so equipped)

NOTE:

The air recirculation feature is available only on those vehicles equipped with air conditioning.

ON position (Indicator light on): Interior air is recirculated inside the vehicle.

button to the on position when:

Push the c driving on a dusty road. c to prevent traffic fumes from entering the

passenger compartment.

c for maximum cooling when using the air con-

ditioner.

OFF position (Indicator light off): Outside air is drawn into the passenger compart- ment and distributed through the selected outlet.

Use the off position for normal heater or air con- ditioner operation.

Air conditioner button (if so equipped)

The button is provided only on vehicles equipped with an air conditioner.

Heater, air conditioner and audio systems 4-3

Z REVIEW COPY—2004 Truck/Frontier (d22) Owners Manual (owners)—USA_English (nna) 05/25/04—arosenma X

button again.

Start the engine, turn the fan control dial to the desired (1 - 4) position and push the button to turn on the air conditioner. The indicator light comes on when the air conditioner is oper- ating. To turn off the air conditioner, push the The air conditioner cooling function oper- ates only when the engine is running. Rear window defroster switch (if so equipped) For more information about the rear window de- froster switch, see (cid:147)Rear window defroster switch(cid:148) in the (cid:147)Instruments and controls(cid:148) section of this manual. HEATER OPERATION Heating This mode is used to direct heated air to the foot outlets. Some air also flows from the defrost outlets. 1. Push the

button (if so equipped) to

the off position for normal heating.

2. Turn the air flow control dial to the

position.

3. Turn the fan control dial to the desired posi-

tion.

4. Turn the temperature control dial to the de- sired position between the middle and the hot position.

Ventilation This mode directs outside air to the side and center ventilators.

1. Push the

button (if so equipped) to

the off position.

2. Turn the air flow control dial to the

position.

3. Turn the fan control dial to the desired posi-

tion.

4. Turn the temperature control dial to the de-

sired position.

Defrosting or defogging This mode directs the air to the defrost outlets to defrost/defog the windows.

1. Turn the air flow control dial to the

position.

2. Turn the fan control dial to the desired posi-

tion.

3. Turn the temperature control dial to the de- sired position between the middle and the hot position.

c To quickly remove ice or fog from the win- dows, turn the fan control dial to 4 and the temperature control lever to the full HOT position. c When the

position is selected, the air conditioner automatically turns on (however, the indicator light will not illuminate) if the outside temperature is more than 36(cid:176)F (2(cid:176)C). The air conditioning system will con- tinue to operate until the fan control dial is turned to OFF or the vehicle is shut off, even is turned to a if the air flow control dial position. This position other than the dehumidifies the air which helps defog the windshield. The mode automatically turns off, allowing outside air to be drawn into the passenger compartment to further improve the defogging performance.

Bi-level heating This mode directs cooler air from the side and center vents and warmer air from the floor outlets. When the temperature control dial is moved to the full hot or full cool position, the air between the vents and the floor outlets is the same tem- perature.

1. Push the

button (if so equipped) to

the off position.

4-4 Heater, air conditioner and audio systems

Z REVIEW COPY—2004 Truck/Frontier (d22) Owners Manual (owners)—USA_English (nna) 05/25/04—arosenma X

2. Turn the air flow control dial to the

position.

3. Turn the fan control dial to the desired posi-

tion.

4. Turn the temperature control dial to the de-

sired position.

Heating and defogging This mode heats the interior and defogs the wind- shield. 1. Turn the air flow control dial to the

position.

2. Turn the fan control dial to the desired posi-

tion.

3. Turn the temperature control dial to the de- sired position between the middle and the hot position.

c When the

position is selected, the air conditioner automatically turns on (however, the indicator light will not illuminate) if the outside temperature is more than 36(cid:176)F (2(cid:176)C). The air conditioning system will con- tinue to operate until the fan control dial is turned to OFF or the vehicle is shut off, even is turned to a if the air flow control dial position other than the position. This dehumidifies the air which helps defog the windshield. so

mode

The

(if

equipped) automatically turns off, allowing outside air to be drawn into the passenger compartment to further improve the defog- ging performance.

Operating tips Clear snow and ice from the wiper blades and air inlet in front of the windshield. This improves heater operation. AIR CONDITIONER OPERATION (if so equipped) Start the engine, turn the fan control dial to the desired (1 - 4) position, and push in the button to activate the air conditioner. When the air conditioner is on, cooling and dehumidifying functions are added to the heater operation. The air conditioner cooling function oper- ates only when the engine is running. Cooling This mode is used to cool and dehumidify the air.

4. Push the comes on.

button. The indicator light

5. Turn the temperature control dial to the de-

sired position.

c For quick cooling when the outside tem- perature is high, push the button to the on position (indicator light on). Be sure to return the button to the off position for normal cooling.

Dehumidified heating This mode is used to heat and dehumidify the air.

1. Push the

button to the off position.

2. Turn the air flow control dial to the

position.

3. Turn the fan control dial to the desired posi-

tion.

4. Push the comes on.

button. The indicator light

5. Turn the temperature control dial to the de-

1. Push the

button to the off position.

sired position.

2. Turn the air flow control dial to the

position.

3. Turn the fan control dial to the desired posi-

tion.

Dehumidified defogging This mode is used to defog the windows and dehumidify the air.

Heater, air conditioner and audio systems 4-5

Z REVIEW COPY—2004 Truck/Frontier (d22) Owners Manual (owners)—USA_English (nna) 05/25/04—arosenma X

1. Turn the air flow control dial to the

position.

2. Turn the fan control dial to the desired posi-

tion.

3. Push the comes on.

button. The indicator light

close the windows. This allows the air con- ditioner to cool the interior more quickly.

c The air conditioning system should be operated for approximately 10 minutes at least once a month. This helps pre- vent damage to the system due to lack of lubrication.

When the or positions in between are selected, the air conditioner automatically turns on (however, the indicator light will not illuminate) if the outside temperature is more than 36(cid:176)F (2(cid:176)C). The air conditioning system will con- tinue to operate until the fan control dial is turned to OFF or the vehicle is shut off, even if the air flow is turned to a position other than control dial the position. This dehumidifies the air which helps defog the windshield. The mode automatically turns off, allowing outside air to be drawn into the passenger compartment to further improve the defogging performance. 4. Turn the temperature control dial to the de-

sired position. Operating tips c Keep the windows closed while the air con-

ditioner is in operation.

c If

the engine coolant

temperature gauge indicates engine coolant tem- perature over the normal range, turn the air conditioner off. See (cid:147)If your vehicle overheats(cid:148) in the (cid:147)In case of emergency(cid:148) section of this manual.

AIRFLOW CHARTS The following charts show the button and dial positions for MAXIMUM AND QUICK heating, cooling or defrosting. The air recirculation button should always be in the OFF posi- tion for heating and defrosting.

c After parking in the sun, drive for 2 or 3
minutes with the windows open to vent hot air from the passenger compartment. Then,

4-6 Heater, air conditioner and audio systems

Z REVIEW COPY—2004 Truck/Frontier (d22) Owners Manual (owners)—USA_English (nna) 05/25/04—arosenma X

LHA0420

LHA0421

Heater, air conditioner and audio systems 4-7

Z REVIEW COPY—2004 Truck/Frontier (d22) Owners Manual (owners)—USA_English (nna) 05/25/04—arosenma X

4-8 Heater, air conditioner and audio systems

LHA0422

LHA0423

Z REVIEW COPY—2004 Truck/Frontier (d22) Owners Manual (owners)—USA_English (nna) 05/25/04—arosenma X

SERVICING AIR CONDITIONER

The air conditioner system in your NISSAN ve- hicle is charged with a refrigerant designed with the environment in mind. This refrigerant does not harm the earth(cid:146)s ozone layer. Special charging equipment and lubricant is re- quired when servicing your NISSAN air condi- tioner. Using improper refrigerants or lubricants will cause severe damage to your air conditioner system. See (cid:147)Air conditioner system refrigerant and lubricant recommendations(cid:148) in the (cid:147)Techni- cal and consumer information(cid:148) section of this manual. A NISSAN dealer is able to service your (cid:147)environ- mentally friendly(cid:148) air conditioning system.

WARNING

The air conditioner system contains re- frigerant under high pressure. To avoid personal injury, any air conditioner ser- vice should be done only by an experi- enced technician with proper equipment.

LHA0424

Heater, air conditioner and audio systems 4-9

Z REVIEW COPY—2004 Truck/Frontier (d22) Owners Manual (owners)—USA_English (nna) 05/25/04—arosenma X

AUDIO SYSTEM

RADIO Turn the ignition key to the ACC or ON position and press the PWR (power)/VOL (volume) knob to turn the radio on. If you listen to the radio with the engine not running, the key should be turned to the ACC position.

Radio reception is affected by station signal strength, distance from radio transmitter, build- ings, bridges, mountains and other external influ- ences. Intermittent changes in reception quality normally are caused by these external influences. Using a cellular phone in or near the ve- hicle may influence radio reception quality. Radio reception Your NISSAN radio system is equipped with state-of-the-art electronic circuits to enhance ra- dio reception. These circuits are designed to extend reception range, and to enhance the qual- ity of that reception.

However there are some general characteristics of both FM and AM radio signals that can affect radio reception quality in a moving vehicle, even when the finest equipment is used. These char- acteristics are completely normal in a given re- ception area, and do not indicate any malfunction in your NISSAN radio system.

Reception conditions will constantly change be- cause of vehicle movement. Buildings, terrain, signal distance and interference from other ve- hicles can work against ideal reception. De- scribed below are some of the factors that can affect your radio reception. FM RADIO RECEPTION Range: FM range is normally limited to 25 - 30
miles (40 - 48 km), with monaural (single chan- nel) FM having slightly more range than stereo FM. External influences may sometimes interfere with FM station reception even if the FM station is within 25 miles (40 km). The strength of the FM signal is directly related to the distance between the transmitter and receiver. FM signals follow a line-of-sight path, exhibiting many of the same characteristics as light. For example they will reflect off objects.

Fade and drift: As your vehicle moves away from a station transmitter, the signals will tend to fade and/or drift.

Static and flutter: During signal interference from buildings, large hills or due to antenna position (usually in conjunction with increased distance from the station transmitter) static or flutter can be heard. This can be reduced by adjusting the treble control to reduce treble response.

4-10 Heater, air conditioner and audio systems

Multipath reception: Because of the reflective characteristics of FM signals, direct and reflected signals reach the receiver at the same time. The signals may cancel each other, resulting in mo- mentary flutter or loss of sound. AM RADIO RECEPTION AM signals, because of their low frequency, can bend around objects and skip along the ground. In addition, the signals can be bounced off the ionosphere and bent back to earth. Because of these characteristics, AM signals are also sub- ject to interference as they travel from transmitter to receiver. Fading: Occurs while the vehicle is passing through freeway underpasses or in areas with many tall buildings. It can also occur for several seconds during ionospheric turbulence even in areas where no obstacles exist. Static: Caused by thunderstorms, electrical power lines, electric signs and even traffic lights.

Z REVIEW COPY—2004 Truck/Frontier (d22) Owners Manual (owners)—USA_English (nna) 05/25/04—arosenma X

c Do not use the following CDs as they may cause the CD player to malfunc- tion: c 3.1 in (8 cm) discs with an adapter c CDs that are not round c CDs with a paper label c CDs that are warped, scratched, or

have abnormal edges

disc DIGITAL AUDIO(cid:148) logo on the disc or packaging.

c During cold weather or rainy days, the player may malfunction due to the hu- midity. If this occurs, remove the CD and dehumidify or ventilate the player completely.

c The player may skip while driving on

rough roads.

c The CD player sometimes cannot func- tion when the compartment tempera- ture is extremely high. Decrease the temperature before use.

c Do not expose the CD to direct sun-

light.

c CDs that are in poor condition or are dirty, scratched or covered with finger- prints may not work properly.

c The following CDs may not work prop-

erly: c Copy control compact discs (CCCD) c Recordable compact discs (CD-R) c Rewritable compact discs (CD-RW)

Heater, air conditioner and audio systems 4-11

Z REVIEW COPY—2004 Truck/Frontier (d22) Owners Manual (owners)—USA_English (nna) 05/25/04—arosenma X

LHA0099
AUDIO OPERATION PRECAUTIONS Compact disc (CD) player c Only use high quality 4.7 inches (12 cm) round discs that have the (cid:147)COMPACT

PRESET ABC button Display

1. 2. 3. CD button 4. CD eject button 5. CD insert slot 6. MENU button AUDIO button 7. Station select buttons 8. 9. SEEK/TRACK button 10. PWR/VOL control knob 11. BAND select button FM-AM RADIO WITH COMPACT DISC (CD) PLAYER (if so equipped) PWR/VOL control knob Turn the ignition key to the ACC or ON position, then push the PWR/VOL control knob. If you listen to the radio with the engine not running, turn the key to the ACC position. The mode (radio or CD) that was playing immediately before the system was turned off resumes playing. When no CD is loaded, the radio comes on. Pushing the PWR/VOL control knob again turns the system off. Turn the PWR/VOL control knob to the right to increase volume or to the left to decrease volume.

4-12 Heater, air conditioner and audio systems

LHA0117

Z REVIEW COPY—2004 Truck/Frontier (d22) Owners Manual (owners)—USA_English (nna) 05/25/04—arosenma X

times for BAL (balance). Once the audio level is set the display will return back to radio or CD display mode after 7 seconds or the AUDIO button can be pressed again within 7 seconds to set the next audio level. Pressing the AUDIO button a fifth time will return the display back to radio or CD display mode.

Fader adjusts the sound level between the front and rear speakers, balance adjusts the sound level between the right and left speakers. Clock set

1. Press and hold the MENU button until

it

beeps (longer than 2 seconds).

2. The

hours will SEEK/TRACK ( hours.

start or

flashing. Press the ) to adjust

3. Press the MENU button until the radio beeps

to switch to the minute adjustment.

LHA0118
Adjusting tone quality and speaker balance

SEEK/TRACK ( utes.

or

4. The minutes will start

flashing. Press ) to adjust the min-

FM-AM radio operation

FM-AM band select

Push the reception.

button to change from AM to FM

The FM stereo indicator, ST, illuminates during FM stereo reception. When the stereo broadcast signal is weak, the radio automatically changes from stereo to monaural reception.

SEEK/manual/SCAN tuning

When the button is pushed while the radio is playing, tuning mode is cycled between: SEEK tuning ! manual tuning ! SCAN mode (cid:147)TUNE(cid:148) and (cid:147)SCAN(cid:148) are shown in the display for each mode. No icon is displayed for SEEK mode.

WARNING

The radio should not be tuned while driv- ing so full attention may be given to ve- hicle operation.

To adjust the audio levels for bass, treble, fader, and balance, push the AUDIO button and adjust the level with the SEEK/TRACK button. Press the AUDIO button once for BASS (bass), twice for TREB (treble), 3 times for FAD (fader) and 4

5. Press the MENU button again to exit the

clock set mode.

The display will return to the regular clock display after 7 seconds, or you may press the MENU button again to return to the regular clock display.

SEEK tuning Push the SEEK/TRACK tuning button ( or ) for less than 1.5 seconds. SEEK tuning begins from low to high frequencies or high to low frequencies, depending on which button is Heater, air conditioner and audio systems 4-13

Z REVIEW COPY—2004 Truck/Frontier (d22) Owners Manual (owners)—USA_English (nna) 05/25/04—arosenma X

and

If using the

pressed, and stops at the next broadcasting sta- button, once the highest tion. broadcasting station is reached, the radio contin- ues in the SEEK mode at the lowest broadcasting station. If using the button, once the lowest broadcasting station is reached, the radio contin- ues in the SEEK mode at the highest broadcast- ing station. Manual tuning Use the buttons for manual tuning. To move quickly through the channels, hold either of the tuning buttons down. SCAN tuning Push and hold the SEEK/TRACK tuning button SCAN illuminates in the display window, and the radio station blinks. SCAN tuning begins from low to high frequencies or high to low frequen- cies, depending on which button is pressed. SCAN tuning stops at each broadcasting station for 5 seconds. When scanning, SCAN is solid and the radio station blinks. When temporarily stopped on a station, SCAN blinks and the sta- tion display is solid. Pushing the button again during this 5 second period stops SCAN tuning and the radio remains tuned to that station.

) for more than 1.5 seconds.

or

Press the PRESET ABC button to change be- tween the presets: A!B!C The radio displays icon A, B or C to indicate which set of presets is active.

To store a radio station in a preset:

1. Select the desired preset by pressing PRE-

SET ABC.

2. Tune to the desired station. 3. Press the desired station select button for more than 3 seconds. For example, in the illustrations, ch2 is to be memorized. The radio mutes when the select button is pushed.

4. When the indicator illuminates in the display and the sound resumes, memorizing is com- plete.

5. Other station select buttons can be set in

the same manner.

If the battery cable is disconnected, or if the radio fuse opens, the radio memory is canceled. In that case, reset the desired stations. Compact disc (CD) player operation Turn the ignition key to the ACC or ON position, and carefully insert the compact disc into the slot

LHA0119

Station memory operations

Each preset mode (A, B or C) has 6 presets, capable of storing any combination of AM and FM stations.

4-14 Heater, air conditioner and audio systems

Z REVIEW COPY—2004 Truck/Frontier (d22) Owners Manual (owners)—USA_English (nna) 05/25/04—arosenma X

with the label side up. The compact disc is auto- matically pulled into the slot and starts to play.

If the radio is already operating, it automatically turns off and the compact disc begins to play.

CAUTION

Do not force a compact disc into the CD insert slot. This could damage the CD and/or CD changer/player.

CD button

When the CD button is pushed with a compact disc loaded and the radio playing, the radio turns off and the compact disc starts to play.

Track up/down, FF/REV (rewind) buttons

Track up/down

When the button is pushed and released while the compact disc is playing, the selection following the present one starts to play from the beginning. Push the button several times to skip several selections. Each time the button is pushed, the CD advances 1 additional selection. The number appears in the display window. (When the last selection on the compact disc is skipped, the first selection is played.)

button is pushed the next selection will be

button is pushed and released, the When the selection being played returns to the beginning. button several times to skip back Push the several selections. Each time the button is pushed, the CD moves back 1 selection. If the play pattern is in MIX mode when the or chosen at random. FF (Fast Forward)/REV (Reverse) When the button is pushed and held while the compact disc is playing, the compact disc plays at an increased speed while fast for- warding or rewinding. When the button is re- leased, the compact disc returns to normal play speed.

or

When a new compact disc is inserted, the play pattern automatically changes to ALL.

CD EJECT button

button is pushed with a com-

When the pact disc loaded, the compact disc ejects. When the button is pushed while the com- pact disc is playing, the compact disc ejects and the system turns off.

DISC indicator light

This light is loaded into the player.

comes on when a compact disc

MENU

button is pushed while the com- When the pact disc is playing, the play pattern changes as follows: RPT: The current selection is repeated. MIX: Selections are played at random, not fol- lowing the sequence on the compact disc. The same program may be repeated twice. If the button is pushed in the MIX mode, selections will be chosen at random. Blank (no symbol): All selections are played repeatedly in sequence.

Heater, air conditioner and audio systems 4-15

Z REVIEW COPY—2004 Truck/Frontier (d22) Owners Manual (owners)—USA_English (nna) 05/25/04—arosenma X

1. Disc loading button 2. SEEK/TRACK button 3. CD select button 4. Band select buttons 5. CD insert slot 6. CD eject button 7. Radio manual tuning buttons 8. RPT MIX/PTY button 9. CLOCK button 10. AUDIO button 11. TRAVEL PRESET button 12. Station select buttons 13. RDS button 14. SCAN button 15. PRESET SCAN button 16. PWR/VOL control knob 17. PRESET ABC button FM-AM RADIO WITH COMPACT DISC (CD) CHANGER (if so equipped) PWR/VOL control knob

Turn the ignition key to the ACC or ON position, then push the PWR/VOL control knob. If you listen to the radio with the engine not running, turn the key to the ACC position. The mode (radio or CD) that was playing immediately before the system was turned off resumes playing.

WHA0134

Z REVIEW COPY—2004 Truck/Frontier (d22) Owners Manual (owners)—USA_English (nna) 05/25/04—arosenma X

4-16 Heater, air conditioner and audio systems

When no CD is loaded, the radio comes on. Pushing the PWR/VOL control knob again turns the system off. Turn the PWR/VOL control knob to the right to increase volume or to the left to decrease volume.

Heater, air conditioner and audio systems 4-17

WHA0065

Z REVIEW COPY—2004 Truck/Frontier (d22) Owners Manual (owners)—USA_English (nna) 05/25/04—arosenma X

Adjusting tone quality and speaker balance

or

or

Press the AUDIO button to enter the audio adjust mode: Bass!Mid!Treb!Fade!Bal Press the TUNE/FF-REV ( ) or SEEK/TRACK ( ) to adjust to the de- sired levels. The display will return to the regular radio display after 7 seconds, or you may press the AUDIO button again to return to the regular radio display. Clock operation Pressing the CLOCK button displays the clock with the radio on or off. Press the CLOCK button again to turn off the clock display. Clock set 1. Press and hold the CLOCK button until it

beeps (>1.5 seconds). start

hours will

2. The

TUNE/FF-REV SEEK/TRACK ( hours.

or

flashing. Press or the

or ) to adjust

3. Press the CLOCK button to switch to the

minute adjustment.

4. Press TUNE/FF-REV (

SEEK/TRACK ( utes.

or

or

) or ) to adjust the min-

5. Press the CLOCK button again to exit the

clock set mode.

The display will return to the regular clock display after 7 seconds, or you may press the CLOCK button again to return to the regular clock display. FM-AM radio operation FM-AM band select Push the AM or the FM button to change from AM to FM reception. The FM stereo indicator, ST, illuminates during FM stereo reception. When the stereo broadcast signal is weak, the radio automatically changes from stereo to monaural reception.

TUNE/FF(cid:151)REV

WARNING

The radio should not be tuned while driv- ing so full attention may be given to ve- hicle operation.

Use the buttons for manual tuning. To move quickly through the channels, hold the tuning buttons down.

and

SEEK tuning

or

Push SEEK/TRACK tuning button ( ). SEEK tuning begins from low to high frequencies or high to low frequencies, depending on which button is pressed, and stops at the next broad- casting station. If using the up button, once the highest broadcasting station is reached, the ra- dio continues in the SEEK mode at the lowest broadcasting station. If using the down button, once the lowest broadcasting station is reached, the radio continues in the SEEK mode at the highest broadcasting station. SCAN tuning Push the SCAN button. SCAN illuminates in the display window. SCAN tuning begins from low to high frequencies. SCAN tuning stops for 5 sec- onds at each broadcasting station that has suffi- cient signal strength. When scanning, SCAN blinks in the display. Pushing the SCAN button again during this 5 second period stops SCAN tuning and the radio remains tuned to that station.

4-18 Heater, air conditioner and audio systems

Z REVIEW COPY—2004 Truck/Frontier (d22) Owners Manual (owners)—USA_English (nna) 05/25/04—arosenma X

3. When the indicator illuminates in the station selection button, a beep will sound indicat- ing memorization is complete. For FM sta- tions, the indicator will turn green. For AM stations, the indicator will turn amber.

4. Other station select buttons can be set in

the same manner.

If the battery cable is disconnected, or if the radio fuse opens, the radio memory is canceled. In that case, reset the desired stations.

LHA0081
Station memory operation (cid:151) Travel Preset is OFF Each preset mode (A, B or C) has 6 presets, capable of storing any combination of AM, FM and FM RDS stations. Press the PRESET ABC button to change be- tween the presets: A!B!C The radio displays icon A, B or C to indicate which set of presets is active.

WHA0064

To store a radio station in a preset:

1. Tune to the desired station.

2. Press the desired station select button (>2
seconds). For example, in the illustrations ch3 is to be memorized.

Heater, air conditioner and audio systems 4-19

Z REVIEW COPY—2004 Truck/Frontier (d22) Owners Manual (owners)—USA_English (nna) 05/25/04—arosenma X

4.

5.

If the radio cannot find any stations, the radio displays (cid:147)NO STATION(cid:148) and mutes the au- dio. If the radio cannot fill all the presets, the remaining presets are stored with 87.9 for FM and 600 for AM.

The TUNE, SCAN, SEEK and preset memory functions are available while Travel Preset mode is on. Canceling travel preset Press the TRAVEL PRESET button (<1.5 sec- onds) to clear the Travel Preset memory. This turns off the green indicator. The radio returns to the last used preset of A, B or C in the permanent preset memory.

LHA0082

Turning ON travel preset

1. Press the TRAVEL PRESET button (<1.5
seconds). The green TRAVEL PRESET but- ton indicator turns on.

2. The radio selects the strongest stations in the area and stores them in Travel Presets A, B and C. 12 FM stations and 6 AM stations are the default settings. To change the de- fault settings, see (cid:147)Editing Travel Preset(cid:148) later in this section.

3. When finished storing radio stations, the radio tunes to the first stored preset of Travel Preset A.

4-20 Heater, air conditioner and audio systems

LHA0084

Z REVIEW COPY—2004 Truck/Frontier (d22) Owners Manual (owners)—USA_English (nna) 05/25/04—arosenma X

Editing travel preset

1. Press and hold the TRAVEL PRESET button (>3 seconds) until the radio beeps to start the editing mode. The green Travel Preset indicator will flash while in TRAVEL PRESET EDIT mode.

2. The presets are transferred from Travel Pre- set memory to the permanent preset memory for A, B, and C. (cid:147)PRESETS LOADED(cid:148) is displayed.

3. The TRAVEL PRESET indicator turns off.

2. The radio displays (cid:147)TRAVEL EDIT(cid:148) for 2
seconds and then changes to (cid:147)SET A-*(cid:148) . ) to

3. Press TUNE/FF-REV (

or

select a mode.

4. Press the TRAVEL PRESET button to save

the mode.

5. Display is changed to (cid:147)SET B-*(cid:148) , repeat

steps 3 and 4.

6. Display is changed to (cid:147)SET C-*(cid:148) , repeat

step 3.

7. Press the TRAVEL PRESET button to exit

the edit mode and return to normal mode.

*: AM, FM, FM RDS, Rock, Classic Rock, Soft Rock, Top 40, Country, Jazz, Classical, Oldies, News, Sports, Talk. Storing Travel Preset stations in permanent memory 1. While in Travel Preset mode, press and hold the TRAVEL PRESET button until it beeps (>3 seconds).

LHA0085

Preset scan Pressing the PRESET SCAN button (<1.5 sec- onds) scans the permanent preset memory that is selected (A, B or C) from 1(cid:150)6 for 5 seconds. If the Travel Preset is ON, the travel preset that is selected (A, B or C) from 1(cid:150)6 is scanned for 5
seconds.

Heater, air conditioner and audio systems 4-21

Z REVIEW COPY—2004 Truck/Frontier (d22) Owners Manual (owners)—USA_English (nna) 05/25/04—arosenma X

stations on the FM band (not AM band) encoded within a regular radio broadcast. Currently, most RDS stations are in large cities, but many stations are now considering broadcasting RDS data.

RDS can display: c Station call sign, such as (cid:147)WHFR 98.3(cid:148). c Station name, such as (cid:147)The Groove(cid:148). c Music or programming type, such as (cid:147)Clas-

sical(cid:148), (cid:147)Country(cid:148), or (cid:147)Rock(cid:148).

c Traffic reports about delays or construction. If the station broadcasts RDS information the RDS icon is displayed. The RDS information will be displayed according to the option chosen in the RDS setup mode. (FM & RDS is the default.) Press the RDS button again to display the fre- quency for 3 seconds. The radio will then return to the normal display. If the station does not broadcast RDS information, the RDS icon will not be displayed. Setting RDS mode

Press and RDS button (>3 seconds) until the display shows (cid:147)RDS SET MODE(cid:148) . This display will last 2 seconds and then change to (cid:147)TRAFFIC-OFF(cid:148) . Press TUNE/FF-REV ( or ) to toggle the RDS traffic mode from (cid:147)OFF(cid:148) to (cid:147)ON(cid:148). Press the RDS button again to set your RDS traffic mode selection.

All preset scan

LHA0086

Pressing the PRESET SCAN button (>1.5 sec- onds) scans all the permanent preset memory banks (A, B or C) from 1(cid:150)6 for 5 seconds. If the Travel Preset is ON, all the travel preset memory banks (A, B or C) from 1(cid:150)6 are scanned for 5
seconds. Canceling preset scan mode Pressing any button except CLOCK, EJECT and PTY cancels the Preset Scan mode. RDS (radio data system) RDS stands for Radio Data System, and is a data information service transmitted by some radio 4-22 Heater, air conditioner and audio systems

or

The display changes to (cid:147)SHOW(cid:148) for the second part of the RDS mode selection. Press TUNE/FF- ) to switch between the REV ( following RDS display modes: c (cid:147)FM & RDS(cid:148): the radio display will show the station(cid:146)s broadcast frequency and the sta- tion(cid:146)s name.

c (cid:147)RDS ONLY(cid:148): the radio display will show the

station(cid:146)s name only.

c (cid:147)RDS TEMP(cid:148): the radio display will show the station(cid:146)s name for 5 seconds and then display only the radio station(cid:146)s broadcast frequency.

PTY (program type) PTY can be used to search for a certain program type. Certain areas have a limited number of stations that transmit RDS. Many stations trans- mit call letters and frequencies only. Searching or scanning by program type may yield a limited number of selections. 1. Press the PTY button. The display changes from (cid:147)RDS PTY SEARCH(cid:148) to (cid:147)SELECT BY TUNE(cid:148) .

or

2. Press TUNE/FF-REV (

up/down button to choose a specific pro- gram type: ROCK, CLASSIC ROCK, SOFT ROCK, TOP 40, COUNTRY, JAZZ, CLASSICAL, OLDIES, NEWS, SPORTS, TALK, ANY

Z REVIEW COPY—2004 Truck/Frontier (d22) Owners Manual (owners)—USA_English (nna) 05/25/04—arosenma X

3. Press the SEEK or SCAN button to search for the next station with the selected PTY. The SCAN icon flashes when the SCAN button is pressed. The radio continues to seek or scan until a radio station is found matching the selected PTY

4. Press the PTY button again to cancel the

PTY SEEK mode.

Compact disc (CD) player operation Turn the ignition key to the ACC or ON position.

CAUTION

c Do not force a compact disc into the CD insert slot. This could damage the CD and/or CD changer/player.

c Trying to load a CD with the CD door closed could damage the CD and/or CD changer.

CD button

When the CD button is pressed with a compact disc loaded and the radio playing, the radio turns off and the last used compact disc starts to play.

4. The CD will play after the disc is set to a play

position.

5. The indicator changes from blinking green to solid green and the display changes to show the Disc number icon, Disc number, Track number and Elapsed time.

All disc loading

1. Press and hold the LOAD button until the

radio beeps (>1.5 seconds).

2. The green indicator on the lowest available disc select button will start blinking. (Same as preset memory button.) The display shows (cid:147)Please Wait(cid:148).

3. The display changes to (cid:147)Insert Disc(cid:148) for a

maximum of 15 seconds.

4. During the 15 second interval,

insert the disc. The display changes to (cid:147)Loading Disc(cid:148).

5. The indicator changes from blinking green

to solid green.

6. The disc number icon is turned on.

LHA0075

CD loading

Press the LOAD button to start CD loading mode.

The following sequence will occur: 1. The green indicator on the lowest available disc select button will start blinking. (Same as preset memory button.) The display shows (cid:147)Please Wait(cid:148) .

2. The display changes to (cid:147)Insert Disc(cid:148) for a

maximum of 15 seconds.

3. During the 15 second interval,

insert the disc. The display changes to (cid:147)Loading Disc(cid:148) .

Heater, air conditioner and audio systems 4-23

Z REVIEW COPY—2004 Truck/Frontier (d22) Owners Manual (owners)—USA_English (nna) 05/25/04—arosenma X

7. Repeat steps 2(cid:150)5 until all discs are loaded, then the last loaded disc will begin to play. The display shows the Disc number, Track number and Elapsed Time.

Selected disc loading 1. Press an available disc select button whose indicator is off. The display shows (cid:147)Please Wait(cid:148).

2. The green indicator starts blinking and the display shows (cid:147)Insert Disc(cid:148) for 15 sec- onds. Insert the CD. The display shows (cid:147)Loading Disc(cid:148).

3.

4. The CD will play after the disc is set to a play

position.

5. The indicator color changes from blinking green to solid green and the display shows the Disc icon, Disc number, Track number and Elapsed Time.

If a disc is not inserted within 15 seconds or if the load button is pressed during load sequence, the entire disc load sequence will be canceled. Disc play Press the CD button. If a CD is loaded and the radio is playing, the radio turns off and the last loaded disc starts to play.

LHA0076

Selected disc play

1. Press the disc select button whose disc icon

is displayed.

2. The indicator blinks green during the change and the display shows (cid:147)Changing Disc(cid:148) .

3. The CD plays after the disc is set to a play

position.

4-24 Heater, air conditioner and audio systems

4. The indicator changes from blinking green to solid green and the display shows the Disc number, Track number and Elapsed Time.

FF (fast forward) REW (rewind) buttons

or

When the TUNE/FF-REV ( ) button is pressed while the compact disc is playing, the compact disc plays at an increased speed while fast forwarding or rewinding. When the button is released, the CD returns to normal play speed. SEEK/TRACK buttons

When is pressed while the compact disc is playing, the selection following the present one starts to play from the beginning. Press sev- eral times to skip several selections. Each time the button is pressed, the CD advances 1 addi- tional selection. The track number appears in the display window. (When the last selection on the compact disc is skipped, the first selection is played.) When is pressed, the selection being played returns to the beginning. Press several times to skip back several selections. Each time the button is pressed, the CD moves back 1 selec- tion. If the play pattern is in MIX mode when the button is pressed the next random selection will be played.

Z REVIEW COPY—2004 Truck/Frontier (d22) Owners Manual (owners)—USA_English (nna) 05/25/04—arosenma X

LHA0077

Repeat/Mix

Press the RPT MIX button to change CD play patterns: Repeat!Mix!All Mix!Normal Play Repeat

Press the RPT MIX button (<1.5 seconds) once to repeat the current track. The (cid:147)1(cid:148) icon is turned on, and the display shows (cid:147)Repeat Track(cid:148) for 2
seconds. The display then shows the Track num- ber and Elapsed time as normal.

Mix Press the RPT MIX button (<1.5 seconds) again to start shuffle play of the current disc. The (cid:147)MIX(cid:148) icon is turned on and the display shows (cid:147)Mix Tracks(cid:148) for 2 seconds. The display then shows the Track number and Elapsed time as normal. All mix Press the RPT MIX button (<1.5 seconds) again to start shuffle play of all discs. The (cid:147)MIX(cid:148) icon is