2007 Mini Cooper Convertible Owners Manual

101

you respond by switching to a recognized high-quality brand such as gasoline that is advertised as Top Tier Detergent Gasoline. Failure to comply with these recommenda- tions may result in unscheduled mainte- nance.<

Manual release with the MINI In the event of an electrical malfunction, the fuel filler door can be unlocked manu- ally. 1. Remove the side trim panel on the left- hand side of the luggage compartment

2. Pull the white lever toward the rear.

The fuel filler door is released

3. Open the fuel filler door.

REFUELING

This gasoline is highly recommended. However, you may also use gasoline with less AKI. The minimum AKI rating is 87. If you use gasoline with this minimum AKI rating, the engine may produce knocking sounds when starting at high outside tem- peratures. This has no effect on the engine life.

Use high-quality brands Field experience has indicated significant differences in fuel quality: volatility, com- position, additives, etc., among gasolines offered for sale in the United States and Canada. Fuels containing up to and includ- ing 10% ethanol or other oxygenates with up to 2.8% oxygen by weight, that is, 15% MTBE or 3% methanol plus an equivalent amount of co-solvent, will not void the applicable warranties with respect to defects in materials or workmanship.

The use of poor-quality fuels may result in driveability, starting and

stalling problems especially under certain environmental conditions such as high ambient temperature and high altitude. Should you encounter driveability prob- lems which you suspect could be related to the fuel you are using, we recommend that

102

REFUELING

Manual release with the MINI Convertible In the event of an electrical malfunction, the fuel filler door can be unlocked manu- ally. 1. Remove the cover of the side trim panel

on the left-hand side, see arrow 1

2. Pull the green strap toward the rear, see

arrow 2. The fuel filler door is released

3. Open the fuel filler door.

103

TIRE INFLATION PRESSURE

Information for your safety It is not merely the tire's service life, but also driving safety and driving comfort that depend on the condition of the tires and the maintenance of the specified tire pres- sure.

Checking tire inflation pressures Check the tire inflation pressures only on cold tires. This means after driving a maxi- mum of 1.25 miles/2 km or when the vehi- cle has been parked for at least 2 hours. Warm tires have higher pressures.

Check the tire inflation pressures reg- ularly and correct them, if necessary,

including the space-saver spare tire: at least twice a month and before an extended trip. Otherwise, incorrect tire pressures can cause driving instability or tire damage, ultimately resulting in acci- dents. Do not drive with deflated, i.e. flat, tires except if Run-Flat Tires are fitted. A flat tire greatly impairs steering and brak- ing response, and can lead to complete loss of control over the vehicle.<

After correcting the tire inflation pressure, reinitialize the Flat Tire

Monitor, refer to page 74.<

104

Tire inflation pressures for original tires The tire inflation pressures for your stan- dard tires are shown on the driver's-side door post, visible when the door is open.

Checking the inflation pressure on the space-saver spare tire Behind the bumper there is a valve exten- sion accessible from the outside for check- ing the inflation pressure.

Tire inflation pressures for other tire sizes In the following tire pressure table, all pres- sures are given for the specified tire sizes at ambient temperature.

Tire size The tire inflation pressures apply to the tire sizes approved and the tire brands recom- mended by the manufacturer of your MINI. Your MINI Dealer will be glad to advise you.

In order to determine the correct inflation pressures for your tires,

refer to the values for the tire size in ques- tion.<

TIRE INFLATION PRESSURE

Model

Tire size All pressure specifications in the table are indicated in psi/kilopascal with cold tires. Cold = ambient temperature

Traveling speeds

175/65 R 15 84 H M+S A/S 175/65 R 15 84 H 195/55 R 16 87 V M+S A/S 195/55 R 16 87 H M+S A/S, Convertible only 195/55 R 16 87 H 205/45 R 17 84 V M+S A/S 205/45 R 17 84 V 175/60 R 15 84 H M+S 175/60 R 16 82 H M+S 195/55 R 16 87 H M+S 205/45 R 17 84 V M+S 205/40 R 18 82 W Space-saver spare tire: T 115/70 R 15 90 M

MINI COOPER/ MINI COOPER Convertible

Pressures specified in psi/kPa

up to 100 mph/

160 km/h

above 100 mph/

160 km/h

30/210

30/210

30/210

30/210

35/240

35/240

33/230

33/230

33/230

33/230

38/260

38/260

61/420

61/420

61/420

61/420

105

TIRE INFLATION PRESSURE

Model

Tire size All pressure specifications in the table are indicated in psi/kilopascal with cold tires. Cold = ambient temperature

Pressures specified in psi/kPa

Traveling speeds

195/55 R 16 87 V M+S A/S 195/55 R 16 87 V 195/55 R 16 87 H M+S 205/45 R 17 84 V M+S A/S 205/45 R 17 84 V M+S 205/45 R 17 84 V 175/60 R 16 82 H M+S 205/40 R 18 82 W 195/55 R 16 87 V M+S A/S 195/55 R 16 87 V 195/55 R 16 87 H M+S 205/45 R 17 84 V M+S A/S 205/45 R 17 84 V M+S 205/45 R 17 84 V 175/60 R 16 82 H M+S 205/40 R 18 82 W

MINI COOPER S

MINI COOPER S with John Coo- per Works Kit*

up to 100 mph/

160 km/h

above 100 mph/

160 km/h

30/210

30/210

30/210

30/210

35/240

35/240

33/230

33/230

33/230

33/230

38/260

38/260

35/240

35/240

35/240

35/240

39/270

39/270

36/250

36/250

36/250

36/250

41/280

41/280

32/220

32/220

32/220

32/220

35/240

35/240

33/230

33/230

33/230

33/230

38/260

38/260

35/240

35/240

35/240

35/240

39/270

39/270

36/250

36/250

36/250

36/250

41/280

41/280

106

TIRE INFLATION PRESSURE

Model

Tire size All pressure specifications in the table are indicated in psi/kilopascal with cold tires. Cold = ambient temperature

Pressures specified in psi/kPa

Traveling speeds

195/55 R 16 87 V M+S A/S 195/55 R 16 87 V 195/55 R 16 87 H M+S 205/45 R 17 84 V M+S A/S 205/45 R 17 84 V M+S 205/45 R 17 84 V 175/60 R 16 82 H M+S 205/40 R 18 82 W 195/55 R 16 87 V M+S A/S 195/55 R 16 87 V 195/55 R 16 87 H M+S 205/45 R 17 84 V M+S A/S 205/45 R 17 84 V M+S 205/45 R 17 84 V 175/60 R 16 82 H M+S 205/40 R 18 82 W

MINI COOPER S Convertible

MINI COOPER S Convertible with John Coo- per Works Kit*

up to 100 mph/

160 km/h

above 100 mph/

160 km/h

30/210

30/210

30/210

30/210

35/240

35/240

33/230

33/230

33/230

33/230

38/260

38/260

35/240

35/240

35/240

35/240

38/260

38/260

36/250

36/250

36/250

36/250

41/280

41/280

32/220

32/220

32/220

32/220

35/240

35/240

33/230

33/230

33/230

33/230

38/260

38/260

35/240

35/240

35/240

35/240

39/270

39/270

36/250

36/250

36/250

36/250

41/280

41/280

More information about permissible loads and weights can be found on pages 151, 152.

107

TIRE CODING

Knowing the tire code on the tire's sidewall makes it easier for you to choose and iden- tify the correct tires.

205/45 R 17 84 V

Tire size e.g. Nominal width in mm Cross-sectional ratio in % Radial belt construction Rim diameter in inches Load index, not on ZR tires Speed code letter, in front of the R on ZR tires

Speed code letters: Q = up to 100 mph / 160 km/h T = up to 118 mph / 190 km/h H = up to 131 mph / 210 km/h V = up to 150 mph / 240 km/h W= up to 167 mph / 270 km/h

Tire Identification Number Tires with DOT codes meet the guidelines of the US Department of Transportation.

108

DOT xxxx xxx 3506

DOT quality grades Tread wear Traction AA A B C Temperature A B C

DOT code: e.g. Manufacturer's code for tire make Tire size and tire version Tire age

All passenger car tires must conform to Federal Safety Requirements in

addition to these grades.<

Tread wear The tread wear grade is a comparative rat- ing based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire graded 150 would wear one and one-half, 1 γ, times as well on the government course as a tire graded 100. The relative performance of tires depends upon the actual conditions of their use, however, and may depart significantly from the norm due to variations in driving habits, service practices and differences in road characteristics and climate.

Tire age The tire's date of manufacture is included in the tire coding: DOT...3506 means that the tire was manu- factured in the 35th week of the year 2006. The manufacturer of your MINI recom- mends replacing all tires after 6 years at the latest, even if a tire service life of 10 years is possible.

Uniform Tire Quality Grading Quality grades can be found where applica- ble on the tire sidewall between tread shoulder and maximum section width. For example: Treadwear 200 Traction AA Temperature A

TIRE CODING

TIRE CONDITION

Standard No. 109. Grades B and A represent higher levels of performance on the labora- tory test wheel than the minimum required by law.

The temperature grade for this tire is established for a tire that is properly

inflated and not overloaded. Excessive speed, underinflation, or excessive loading, either separately or in combination, can cause heat buildup and possible tire fail- ure.<

RSC: Run-Flat Tires You will recognize Run-Flat Tires by a circu- lar symbol containing the letters RSC on the side of the tire, refer to page 111.

M+S Winter and all-season tires. These have better winter performance properties than summer tires.

Inspect your tires frequently for tread wear, signs of damage and for foreign objects lodged in the tread. Check the tread depth.

Tire tread Tread depth should not be allowed to go below 1/8 in/3 mm even though in Europe, for example, the legally specified minimum tread depth is only 1/16 in/1.6 mm. Below 1/8 in/3 mm tread depth, there is a very high danger of hydroplaning at higher speeds, even with only small amounts of water on the road. At tread depths below approx. 1/6 in/ 4 mm, the ability of winter tires to cope with winter driving conditions decreases perceptibly. For safety reasons, new tires should be mounted.

Traction The traction grades, from highest to low- est, are AA, A, B, and C. Those grades represent the tire‘s ability to stop on wet pavement as measured under controlled conditions on specified govern- ment test surfaces of asphalt and concrete. A tire marked C may have poor traction per- formance.

The traction grade assigned to this tire is based on straight-ahead brak-

ing traction tests, and does not include acceleration, cornering, hydroplaning, or peak traction characteristics.<

Temperature The temperature grades are A, the highest, B and C, representing the tire's resistance to the generation of heat and its ability to dissipate heat when tested under con- trolled conditions on a specified indoor lab- oratory test wheel. Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure. The grade C corresponds to a level of performance which all passenger car tires must meet under the Federal Motor Vehicle Safety

109

TIRE CONDITION

Wheel/tire damage

Due to low-profile tires, please note that wheels, tires and suspension

parts are more susceptible to road hazards and consequential damage. Unusual vibrations during driving may indi- cate tire damage or other damage to the vehicle. This may be caused, for example, by driving over a curb. This is also true for abnormalities in the vehicle's handling characteristics, such as a pronounced ten- dency to pull to the left or right. In such situations, reduce your speed immediately. Drive carefully to the nearest MINI Dealer or tire dealer, or have the vehi- cle towed there, if necessary. Tire damage can endanger the lives of both the vehicle occupants and other road users.<

Wear indicators in the tread-groove base are spread around the circumference of the tire and are marked on the sidewall of the tire with TWI, Tread Wear Indicator. When tire tread is worn down to the level of the wear indicators, the remaining tread depth is 1/16 in/1.6 mm.

110

RUN-FLAT TIRES*

You will recognize Run-Flat Tires by a circu- lar symbol containing the letters RSC on the side of the tire. Run-Flat Tires consist of conditionally self- supporting tires and special rims. The tire reinforcement ensures that driving remains possible to a restricted degree in the event of a pressure drop or even a flat tire. For information on continuing to drive with a flat tire, refer to Flat tire warning, page 75.

Tire change set

In case of a flat tire, the tire change set is not needed, since your vehicle

has Run-Flat Tires. When changing a tire, always observe the safety measures and the procedure for changing tires starting on page 133.<

Your vehicle is additionally equipped with a tire change set. In the MINI COOPER and MINI COOPER Con- vertible this is located in the luggage com- partment under the floor mat. In the MINI COOPER S and MINI COOPER S Convertible, the tire change set is located in a separate bag which is attached to the lashing eyelets on the luggage compart- ment floor by means of tie-down straps.

Have new wheels and tires mounted only by your MINI Dealer or a special- ized tire shop that has specially trained per- sonnel working in accordance with the specifications of the MINI manufacturer. Work that is improperly carried out could result in consequential damage and pose safety hazards.<

Retreaded tires

The manufacturer of your MINI rec- ommends that you avoid using

retreaded tires, as this could impair driving safety. This is due to possible variations in casing structures and, in some cases, to their extreme age, factors which can lead to limited durability.<

111

Run-Flat Tires For your own safety, use Run-Flat Tires when mounting new tires or replacing summer tires with winter tires or vice versa. Keep in mind that no spare wheel is available in the event of a flat. Your MINI Dealer will be glad to advise you.

For safety reasons, the manufacturer of your MINI recommends having

Run-Flat Tires replaced, not repaired, if they are damaged.<

Tire designation For each tire size, the manufacturer of your MINI recommends certain tire brands. You can recognize these by the clearly visible designation on the tire's sidewall. When used properly these tires meet the highest standards regarding safety and handling characteristics.

NEW WHEELS AND TIRES

The correct wheels and tires

The manufacturer of your MINI rec- ommends mounting only wheels and

tires that it has specifically approved for use on your particular model. Although other wheels and tires may theoretically have the same dimensions, variations in factors such as manufacturing tolerances can result in contact between tire and bodywork, ultimately leading to serious accidents. The manufacturer of your MINI cannot evaluate non-approved wheels and tires to determine if they are suited for use, and therefore cannot ensure the operating safety of the vehicle if they are mounted.<

Your MINI Dealer will be glad to inform you about the correct wheel and tire combina- tion for your vehicle. The correct wheel and tire combination is also important for various systems that would otherwise be impaired, e.g. ABS or DSC. To maintain good handling and vehicle response, use only tires of a single brand and tread configuration. In the event of tire damage, remount the previous wheel and tire combination as soon as possible.

112

NEW WHEELS AND TIRES

SNOW CHAINS*

Special characteristics of winter tires The manufacturer of your MINI recom- mends winter tires for driving in adverse winter road conditions. While all-season tires with the M+S designation provide bet- ter winter traction than summer tires, they generally do not achieve the full perfor- mance of winter tires.

Observe speed ratings:

Never exceed the maximum speed for which the winter tires are rated.<

Storage Store tires in a cool, dry place, protecting them against light whenever possible. Pro- tect the tires against contact with oil, grease and fuel. Do not exceed the tire inflation pressure specified on the tire side- wall.

Only certain types of snow chains have been tested by the manufacturer of your MINI, classified as road-safe and recom- mended. Contact your MINI Dealer for more details. Their use is only permitted in pairs on the front wheels on winter tires of the following types: >175/65 R 15 M+S >175/60 R 16 M+S. When fitting, comply with the manufac- turer's instructions. With chains, do not exceed a speed of 30 mph / 50 km/h.

Do not initialize the Flat Tire Monitor after attaching snow chains to the

tires. When driving with snow chains, it can be helpful to switch off the ASC or DSC for a brief period, refer to page 72.<

113

BONNET

Do not attempt to service your vehi- cle if you do not have the required

technical background. If you are not famil- iar with the regulations to be observed, have the necessary work on your vehicle carried out only by a MINI Dealer or a work- shop that has specially trained personnel working in accordance with the specifica- tions of the MINI manufacturer. Work that is improperly carried out could result in consequential damage and pose safety hazards.<

114

To unlock Pull the lever in the right door area beneath the instrument panel.

To open 1. Reach under the bonnet 2. Pull the release lever 3. Open the bonnet.

To close Allow the bonnet to fall from a height of approx. 1 ft/30 cm.

Make sure that the closing range of the bonnet is unobstructed, other-

wise personal injury could result. If it is determined that the bonnet is not completely closed while driving, stop immediately and close it securely, also refer to page 17.<

ENGINE COMPARTMENT: MINI COOPER AND MINI COOPER CONVERTIBLE

1 Reservoir for windshield and rear

window washer system* 64
2 Vehicle identification number 3 Coolant expansion tank 118

4 Engine oil filler neck 117
5 Battery 140
6 Brake fluid reservoir 120

7 Reservoir for headlamp cleaning

system* 64

8 Engine oil dipstick 117

115

ENGINE COMPARTMENT: MINI COOPER S AND MINI COOPER S CONVERTIBLE

1 Reservoir for windshield and rear

window washer system* 64
2 Vehicle identification number

3 Coolant expansion tank 118
4 Engine oil filler neck 117
5 Auxiliary terminal for

jump-starting 142

6 Brake fluid reservoir 120
7 Reservoir for headlamp cleaning

system* 64

8 Engine oil dipstick 117

116

ENGINE OIL

Measuring the oil level 1. With the vehicle's engine at normal

operating temperature, i.e. after unin- terrupted driving for at least 6 miles/ 10 km, park the vehicle on a level surface

2. Switch off the engine 3. Pull the dipstick out after approx.

5 minutes and wipe it off with a lint-free cloth, paper towel, or similar material 4. Carefully push the dipstick all the way

into the guide tube and pull it out again. The oil level should be between the two marks on the dipstick.

As with fuel economy, oil consumption is directly influenced by your driving style and vehicle operating conditions. The oil volume between the two marks MIN, MAX on the dipstick corresponds to approx. 1.1 quarts/1 liter.

Do not fill beyond the upper mark on the dipstick. Excess oil will damage

the engine.<

Adding engine oil

Only top up oil when the oil level has dropped to just above the lower mark

of the dipstick. However, never allow the level to drop below the lower mark.<

Add oil within the next 30 miles/ 50 km, otherwise the engine could be

damaged.<

Always store oil, grease, etc., out of reach of children. Comply with all warning labels and information on lubri- cant containers, otherwise health risks may result.<

Oil change Have the oil changed only by a MINI Dealer or a workshop that has specially trained personnel working in accordance with the specifications of the MINI manufacturer.

117

ENGINE OIL

COOLANT

The correct SAE grade for your MINI is determined by the climatic conditions of the region in which you normally drive your MINI.

Do not open the cooling system when the engine is hot. Escaping coolant

can cause burns.<

Approved oils feature the SAE grades 5W-40 and 5W-30.<

These oils can be used for driving at all out- side temperatures.

Coolant consists of water and a coolant additive. Not all commercially available additives are suitable for your MINI. Your MINI Dealer knows which additives are suitable and will be glad to advise you.

Only use suitable additives, other- wise the engine can be damaged. The

additives are hazardous to your health.<

Comply with the applicable environ- mental laws regulating the disposal

of coolant additives.<

Approved engine oils The quality of the engine oil selected has critical significance for the operation and service life of an engine. Based on exten- sive testing, the manufacturer of your MINI approves only certain grades of engine oil. Only use High Performance Synthetic Oil approved by the manufacturer of your MINI. If MINI High Performance Synthetic Oil is not available, you can add small quantities of another synthetic oil in between oil changes. Only use oils with a specification of API SH or higher.

If you have any further questions regarding MINI High Performance Synthetic Oil or approved synthetic oils, your MINI Dealer will be glad to advise you.<

Do not use any oil additives, as they could cause engine damage under

some circumstances.<

Viscosity grades Viscosity is a measure of an oil's flow rating and is classified into SAE grades.

118

3. The coolant level is correct if it is

between the MIN and MAX markings on the transparent expansion tank

4. If necessary, slowly add coolant until the

correct level is reached; do not overfill 5. MINI COOPER and MINI COOPER Con-

vertible: Reattach the cap and press it down firmly MINI COOPER S and MINI COOPER S Con- vertible: Screw the cap back on and tighten it firmly

6. Have the cause of the coolant loss

removed as soon as possible.

COOLANT

As an example, the illustration shows the coolant tank of the MINI COOPER and the MINI COOPER Convertible.

Checking coolant level 1. The engine must be at ambient temper-

ature

2. MINI COOPER and MINI COOPER Con-

vertible: Slowly pull the cap of the expansion tank by the tab until the excess pressure can escape. Then remove the cap com- pletely. MINI COOPER S and MINI COOPER S Con- vertible: Slightly unscrew the cap of the expan- sion tank counterclockwise until the excess pressure can escape. Then remove the cap completely

119

BRAKE SYSTEM

Brake fluid level

The warning lamp comes on although the parking brake is not engaged:

The brake fluid level in the reservoir is too low, refer to page 16. At the same time, brake pedal travel may become signifi- cantly longer. Have the system checked immediately. If the brake fluid level is too low and brake pedal travel has become longer, there may be a defect in one of the brake system's hydraulic circuits.

Canadian models display this warning lamp.

If you continue driving, higher brake application pressure may be neces-

sary, and there may be a slight pull to one side. Brake pedal travel may also be longer. Adapt your driving style accordingly.<

120

MINI MAINTENANCE SYSTEM

The MINI maintenance system helps main- tain your vehicle's road safety and opera- tional safety. Please bear in mind that regular mainte- nance is not only necessary for the safety of your vehicle, but also plays a significant role in maintaining the resale value of the vehicle.

Service interval display While conventional systems determine maintenance intervals according to fixed kilometer readings, the MINI Maintenance System takes the vehicle's driving condi- tions into account because not every mile is the same as another in this respect. From a maintenance standpoint, 60,000 miles/100,000 km accumulated through short-distance driving cannot be treated the same as 60,000 miles/ 100,000 km accumulated through long-dis- tance highway travel. The condition-based MINI Maintenance System includes the Engine Oil Service and Inspections I and II. Determining the maintenance intervals according to the actual use of the vehicle covers every kind of operating situation. People who drive very little, i.e. much less than 6,000 miles/10,000 km per year, should have the engine oil changed at least every 2 years since oil deteriorates over time, regardless of use. For more information on the service inter- val display, refer to page 69.

Service and Warranty Information Booklet for US models, Warranty and Service Guide Booklet for Canadian models For additional information on maintenance intervals and procedures, please refer to the Service and Warranty Information Booklet for US models or the Warranty and Service Guide Booklet for Canadian models. As a precaution against rust, it is advisable to have the body checked for damage from rocks or gravel at the same time, depending upon operating conditions.

The manufacturer of your MINI rec- ommends having maintenance and

repair work carried out only by a MINI Dealer or a workshop that has specially trained personnel working in accordance with the specifications of the MINI manu- facturer. Make sure that maintenance work is con- firmed with an entry in the Service and Warranty Information Booklet for US models or the Warranty and Service Guide Booklet for Canadian models. These entries are your proof that the vehicle has received regular maintenance.<

121

SOCKET FOR ONBOARD DIAGNOSTICS OBD

CARING FOR YOUR VEHICLE

speed and visit your nearest MINI Dealer as soon as possible. Severe engine misfiring can quickly lead to serious damage of emis- sions-related components, especially the catalytic converter.

If the fuel filler cap is not properly tightened, the OBD system may con- clude that fuel vapors are escaping, causing an indicator to light up. If the filler cap is then tightened, the indicator should go out within a few days.<

Suitable car-care products

Use the cleaning and car-care prod- ucts available at your MINI Dealer.<

Washing your vehicle You can wash your new MINI or MINI Con- vertible in automatic car washes from the beginning. Preference should be for cloth car washes. If, due to lack of availability, brush car washes must be used, modern systems with soft brushes should be given preference.

When using steam cleaners or high- pressure cleaners, maintain sufficient distance to the vehicle and do not exceed a maximum temperature of 1407/606. If the jet is too close or the pressure is too high, this can lead to damage or initial damage that can develop into more serious damage. Water that enters vehicle compo- nents can lead to damage over the long term. After washing the vehicle, apply the brakes briefly to dry them, otherwise water can reduce braking efficiency over the short term and the brake rotors can corrode. Switch the rain sensor off when passing through an automatic car wash, refer to page 63. Failure to do so could result in

Primary components of exhaust emissions can be checked by a device via the OBD socket. This socket is located to the left of the driver's side, on the bottom of the instru- ment panel underneath a cover.

Exhaust emission values

The warning lamp comes on. The exhaust emissions have deterio- rated. Have the vehicle checked as

soon as possible.

Canadian models display this warning lamp.

Under some circumstances, the lamp will flash. This indicates severe engine misfir- ing. In this case, you should reduce your

122

CARING FOR YOUR VEHICLE

damage caused by undesired wiper activa- tion.<

Rod antenna

If necessary, for example before entering a car wash or a garage with

elevator ramp, remove the rod antenna. To do so, grip the rod antenna at the base and unscrew it from the antenna foot by turning it to the left.<

Headlamps

When cleaning the headlamps, please note: do not rub the head-

lamps dry and do not use any abrasive or caustic cleaning products. Remove dirt and contamination, such as insects, by soaking with shampoo and then rinsing with plenty of water. Always use a deicer spray to remove accumulated ice and snow; never use a scraper.<

Vehicle paintwork Regular care contributes greatly to driving safety and value retention. Environmental influences varying from one region to the next can affect the vehicle paintwork. Please base the frequency and scope of car care on these various influ- ences.

Care of upholstery Depressions that come about on the uphol- stery material of the seats in daily use can be brushed out using a slightly damp brush against the grain. The fact that velour lays down is not a qual- ity defect, but rather is inevitable in the case of home textiles or clothing materials. In the case of strong sunlight and longer parking periods, cover the seats or all win- dows to prevent discoloration.

Care of special parts >Light-alloy wheels*:

Use wheel cleaner especially during the winter months, but do not use any aggressive, acidic, strong alkali or rough cleansers or steam jets above 1407/ 606. Observe the manufacturer's instructions

>Chrome parts* such as the bonnet grille,

door handles, and similar parts: Particularly if they were exposed to road salt, clean these parts carefully with plenty of water and shampoo additive, if necessary. For additional treatment, use chrome polish

>Rubber components:

Treat only with water or rubber care products.

Do not use silicon sprays or other silicon-containing care products,

otherwise noise and damage could occur.<

>Plastic parts, artificial leather surfaces, headliner, lamp lenses, cover glass over display elements as well as matt-black die-cast parts: Clean these parts with water and plastic care products, if necessary. Do not dampen seats and the headliner. Never use solvents such as lacquer thin-

123

CARING FOR YOUR VEHICLE

ner, heavy-duty grease remover, fuel or similar

>Fine-wood parts*:

Please clean wood paneling and other wood parts only with a damp cloth. Dry off with a soft cloth

>Safety belts:

Only clean using mild soap, leaving the belts installed. Do not dry clean, as the fabric can be destroyed. Always roll up safety belts only when dry. Dirty safety belts prevent unrolling and thus negatively affect safety >Floor carpets and floor mats*:

Use an interior cleaner to clean these items if they are heavily soiled. Floor mats can be removed to allow the inte- rior to be cleaned

>Wiper blades:

Clean with soap and water. Replace wiper blades twice a year, before and after the cold season. This is particularly important on vehicles fitted with a rain sensor.

Caring for leather* and imitation leather The leather and imitation leather used by the manufacturer of your MINI are high

quality products processed using state-of- the-art methods and will retain their qual- ity level for many years if cared for prop- erly. Regular cleaning and care are necessary, as dust and road dirt scratch in pores and creases and lead to heavy wear as well as premature brittleness of the leather and imitation leather surface. This is why you should use a cloth or vac- uum cleaner to remove dust on a regular basis. Since dirt and oil slowly destroy the protec- tive layer of the leather and imitation leather, a treatment with a leather care product is necessary twice a year. This pre- serves the quality of the leather and pre- vents electrostatic charging.

Cleaning agents can contain hazard- ous or health-damaging substances. For this reason, always observe the warn- ings on the package. For interior cleaning, always open the doors or windows of the vehicle. Do not use any products that are not intended for cleaning the vehicle.<

124

Care of the MINI Convertible's top The appearance and service life of the con- vertible top largely depend on the proper care and operation of the convertible top. You should therefore observe the following notes in particular: >Whenever possible, park your vehicle in the shade to protect it from intense sun- light

>Do not fold the convertible top when it is

wet, dirty or frozen; otherwise water marks, moisture stains and chafing could result

>If the vehicle is parked in an enclosed area for a longer period of time, make sure that there is sufficient ventilation

>Remove bird droppings immediately

because they have corrosive properties.

Never use spot removers, paint thin- ner, solvents, cleaning fuel or similar since these products can destroy the rubber seals and cause leaks.<

CARING FOR YOUR VEHICLE

VEHICLE STORAGE

Your MINI Dealer will be glad to advise you on what is important if the vehicle is to be decommissioned for longer than three months.

If the convertible top is very dirty, it is rec- ommended that it be cleaned with a spe- cial convertible top cleaning agent. Your MINI Dealer will be glad to advise you. Clean the convertible top as follows: >Spray the convertible top with an

approved convertible top cleaning agent

>Then scrub the convertible top with a

wet sponge using circular motions

>Afterward, finish cleaning the vehicle in

a car wash or rinse the convertible top thoroughly with plenty of water.

After washing the convertible top three to five times, it should be treated with a waterproofing agent.

Wind deflector* >Clean the wind deflector with a soft sponge and water evenly across the entire surface so that water marks do not form

>Do not clean it with a vacuum cleaner or upholstery brush attachment, otherwise the net could be damaged.

125

126

OVERVIEW

CONTROLS

OPERATION, CARE, MAINTENANCE

OWNER SERVICE PROCEDURES

TECHNICAL DATA

INDEX

127

Repairs

ONBOARD TOOL KIT

WIPER BLADES

Tire change set with onboard tools for space-saver spare tire In the luggage compartment under the floor mat.

MINI Mobility System with tire change set and onboard tools In the luggage compartment under the floor mat.

Tire change set and onboard tool kit with Run-Flat Tires MINI COOPER and MINI COOPER Convert- ible: >In the luggage compartment under the

floor mat.

MINI COOPER S and MINI COOPER S Con- vertible: >Tire change set:

in the luggage compartment in a sepa- rate pouch

>Onboard tool kit:

in the luggage compartment under the floor mat.

Windshield wiper 1. Rotate the wiper arm completely out 2. Set the wiper blade at an angle 3. Press the securing spring, see arrow 4. Unhook the wiper blade towards the

windshield

5. Pull the wiper blade past the wiper arm

toward the top

6. Insert the new wiper blade 7. Press into position until you hear it

engage.

The picture shows as an example the tire change set with onboard tools for vehicles with the space-saver spare tire. Depending on the equipment version, your vehicle is equipped with a special onboard tool kit stored at the locations described below:

128

WIPER BLADES

LAMPS AND BULBS

Whenever working on the electrical system, switch off the electrical

accessory you are working on or disconnect the cable from the negative terminal of the battery. Failure to do this could result in short circuits. To prevent injuries and damage, comply with any instructions provided by the bulb manufacturer.<

Lamps and bulbs are an important compo- nent of vehicle safety. Therefore, proceed carefully when handling bulbs. To replace bulbs which are not described here, please contact a MINI Dealer or a workshop that has specially trained per- sonnel working in accordance with the specifications of the MINI manufacturer.

Do not touch the glass portion of a new bulb with your bare hands since even small amounts of impurities burn into the surface and reduce the service life of the bulb. Use a clean cloth, paper napkin, or similar material, or hold the bulb by its metallic base.<

A replacement bulb set can be obtained at your MINI Dealer.

Rear window wiper* 1. Rotate the wiper arm completely out 2. Turn the wiper blade as far as it will go

to the rear

3. Press the wiper blade against the limit

and thus out of the mounting

4. Press the new wiper blade into the

mounting.

129

LAMPS AND BULBS

1 Low beams H7 bulb, 55 watts

2 High beams H7 bulb, 55 watts

The H7 bulb is pressurized. Therefore, wear safety glasses and protective gloves. If the lamp is damaged there is a risk of injury.<

For checking and adjusting headlamp aim, please contact your MINI

Dealer.<

Replacing bulbs The headlamps are integrated into the bon- net.

130

1. Gently pull the retaining wire of the

headlamp cover and guide it outwards

2. Fold down the headlamp cover 3. Disconnect the cable connector from the

bulb socket and pull out the bulb

4. Place the bulb holder on the lower edge

of the mounting and press it in until it engages in the bulb socket

5. Reconnect the cable connector and

install the headlamp cover again.

Xenon lamps* The service life of these bulbs is very long and the probability of a failure is very low, provided that they are not switched on and off an unusual number of times. If one of these bulbs should nevertheless fail, it is possible to continue driving with great cau- tion using the fog lamps, provided traffic laws in your area do not prohibit this.

Turn signal indicators, front 21 watt bulb 1. Open the bonnet 2. Reach into the opening for the turn sig-

nal indicators from above

3. Apply gentle pressure to the bulb holder

while turning it to the left

4. Remove and replace the bulb.

Have any work on the xenon lamp system, including bulb replacement, carried out only by a MINI Dealer or a work- shop that has specially trained personnel working in accordance with the specifica- tions of the MINI manufacturer. Due to high voltage, there is a risk of fatal injury if work on the xenon lamps is carried out improperly.<

Parking lamps and standing lamps 5 watt bulb The parking lamps and standing lamps are integrated in the lamp housing of the turn signal indicator. 1. Turn the bulb holder to the left and pull

out

2. Remove and replace the bulb.

LAMPS AND BULBS

Side turn signal indicators 5 watt bulb 1. Slide the lamp toward the rear of the

vehicle and remove

2. Remove and replace the bulb.

Tail lamps Turn signal lamp 1: Rear lamp 2: Backup lamp 3:

21 watts 21/5 watt bulb 16 watts

1 Turn signal indicator 2 Rear lamp/Brake lamp 3 Backup lamp

yellow red white

Replacing bulbs To access the bulb holder, remove the cover on the side panel in the luggage compart- ment for MINI and MINI Convertible. 1. Unplug the power supply, arrow 1
2. Squeeze the retaining clips together, see