Login- Download PDF Manual
-
Rthat are parallel to the direction of travel Rthat are on straight roads, not bends Rthat are on the same level as the road, i.e. not on the pavement, for example. Parking Guidance may not detect flat curbs
Parking tips: Ron narrow roads, drive past the parking
space as close as possible.
Rparking spaces that are littered, overgrown
or partially occupied by trailer drawbars might be identified incorrectly or not at all. Rsnowfall or heavy rain may lead to a parking
space being measured inaccurately.
Rpay attention to the PARKTRONIC
(Y page 203) warning messages during the parking procedure.
Rwhen transporting a load which protrudes from your vehicle, you must not use Parking Guidance.
Rnever use Parking Guidance with snow
chains or an emergency spare wheel installed.
Rmake sure that the tire pressures are
always correct. This has a direct effect on the steering instructions.
Rthe way your vehicle is positioned in the parking space after parking is dependent on various factors. These include the position and shape of the vehicles parked in front and behind it and the conditions of the location. In some cases, Parking Guidance may guide you too far or not far enough into a parking space. In some cases, it may also lead you across or onto the curb. If necessary, cancel the parking procedure with Parking Guidance.
Detecting a parking space
Example: vehicles featuring a DIRECT SELECT lever : Detected parking space on the left ; Parking symbol = Detected parking space on the right Parking Guidance is automatically activated when you drive forwards. The system is operational at speeds of up to approximately 22 mph (35 km/h). While in operation, the system independently locates and measures parking spaces on both sides of the vehicle. When driving at speeds below 19 mph (30 km/h), you will see parking symbol ; as a status indicator in the instrument cluster.
When a parking space has been detected, an arrow towards the right = or the left : also appears. Parking Guidance only displays parking spaces on the front-passenger side as standard. Parking spaces on the driver's side are displayed as soon as the turn signal on the driver's side is activated. To park on the driver's side, you must leave the driver's side turn signal switched on until you have engaged reverse gear. Parking Guidance will only detect parking spaces: Rthat are parallel to the direction of travel Rthat are at least 5 ft (1.5 m) wide Rthat are at least 4.3 ft (1.3 m) longer than
your vehicle
A parking space is displayed while you are driving past it, and until you are approximately 50 ft (15 m) away from it.
Parking Important safety notes G WARNING The Parking Guidance is only an aid and may not detect all obstacles. The Parking Guidance does not relieve you of the responsibility to pay attention. You are always responsible for safety and must continue to pay attention to your immediate surroundings when parking and maneuvering. Otherwise, you could endanger yourself and others.
Moving the vehicle into the stop position
Driving systems
207
X Stop the vehicle when the parking space
symbol shows the desired parking space in the instrument cluster.
X Shift the transmission to position R. The multifunction display shows the Check Vehicle Surroundings Press 'OK' to Confirm message. X Press the a button on the multifunction
steering wheel to confirm. The multifunction display switches to Parking Guidance. Depending on your distance from the parking space, the Please Drive Backward message will appear in the multifunction display.
X If necessary, reverse towards the parking
space. This is indicated by an arrow pointing backwards. Continue backing up until you hear a tone. Stop – the parking position has been reached. The arrow is white. The Please Steer Wheel to the Right or Please Steer Wheel to the Left message appears in the multifunction display.
Backing up into the parking space
X While the vehicle is stationary, turn the steering wheel in the specified direction until the arrow is white and a warning tone sounds.
X To reverse into the parking space: maintain the steering wheel angle and reverse carefully.
X Stop as soon as you hear a warning tone,
The vehicle has reached the position in which you need to countersteer.
208 Driving systems
The Please Steer Wheel to the Left or Please Steer Wheel to the Right message appears in the multifunction display.
X Countersteering: while the vehicle is
stationary, turn the steering wheel in the specified direction until the arrow is white and a warning tone sounds.
X To reverse into the parking space: maintain the steering wheel angle and reverse carefully.
X Stop as soon as you hear a warning tone, at the latest when PARKTRONIC sounds the continuous warning tone. The Parking Guidance Finished message appears in the multifunction display and a tone sounds. You may be asked to steer in a different direction and then change gear. In this case, further displays in the multifunction display will direct you to the final position.
X Maneuver if necessary. X Always observe the warning messages
displayed by PARKTRONIC (Y page 203).
Canceling Parking Guidance X Press the PARKTRONIC button on the
center console (Y page 204). Parking Guidance is canceled immediately and PARKTRONIC is deactivated.
Parking Guidance is canceled automatically if it is no longer possible to guide you into the parking space, or if a malfunction occurs. The parking space symbol goes out and a warning tone sounds. The Parking Guidance Canceled message appears in the multifunction display.
Rear view camera Important safety notes G WARNING Make sure that no persons or animals are in the maneuvering range. Otherwise, they could be injured.
General notes
Example: Sedan Rear view camera : is an optical parking aid. It shows the area behind your vehicle in the COMAND display. Rear view camera : is located in the handle strip of the tailgate.
View through the camera G WARNING The rear view camera is only an aid and may display obstacles Rfrom a distorted perspective Rinaccurately Rmay not display obstacles at all The rear view camera does not relieve you of the responsibility to be cautious. Take care and pay careful attention. The rear view camera may not show objects which are Rvery close to the rear bumper Runder the rear bumper Rabove the tailgate handle
Driving systems
209
You are responsible for safety at all times and must continue to pay attention to the immediate surroundings when parking and maneuvering. This includes the area behind, in front of, and beside the vehicle. Otherwise you could endanger yourself and/or others. G WARNING The rear view camera will not function or will not fully function if: Rthe tailgate is open Rit is raining or snowing strongly or if it is
foggy
Rit is night or if you are parking/
maneuvering your vehicle in a very dark area
Ra very bright white light is affecting the
camera
Rthe immediate vicinity is illuminated with fluorescent light (the display can flicker)
Rtemperature changes abruptly, for example
if you drive out of the cold into a heated garage (condensation on the lens) Rthe camera lens is dirty or covered Rthe rear of your vehicle is damaged
In this case, have the position and the setting of the camera checked at a specialist workshop. Mercedes-Benz recommends that you consult a Mercedes- Benz Center for this purpose.
Do not use the rear view camera in these situations. You could otherwise injure yourself and other people and/or cause damage - including damage to your vehicle - while parking/maneuvering.
The area behind the vehicle is displayed as a mirror image, as in the rear view mirror.
Activating the rear view camera X Make sure that the SmartKey is in position
2 in the ignition lock.
X Make sure that the rear view camera
function is selected in COMAND (see the
separate operating instructions for COMAND).
X Engage reverse gear.
The area behind the vehicle is shown in the COMAND display with guide lines.
Guide lines in the COMAND display G WARNING Use of rear view camera can be dangerous if you are color-blind or have impaired color vision. Only use rear view camera if you can see and distinguish all colored guidelines shown by rear view camera on the COMAND system display. G WARNING Please note that objects that do not touch the ground may appear to be further away than they actually are, for example: Rthe bumper of a vehicle parked behind you Rthe trailer drawbar Rthe ball coupling of a trailer tow hitch Rthe rear end of a truck Ra slanted post In such cases, you should not use the guide lines to judge the distance. You may misjudge the distance, which increases the risk of impacting the objects. Even if the object you approach is directly on the ground, do not approach the object any closer than the red guide line.
Example: information in the COMAND display
210 Driving systems
Guide lines ; and = show the approximate distance to the rear area. Yellow guide line ; indicates a distance of approximately 3 ft (1 m) and red guide line = indicates a distance of approximately 10 in (0.25 m). The distances only apply to objects that are at ground level. Blue guide lines : depict the width required for the vehicle. They are used to align the vehicle with the edge of the road, e.g. the curb.
ATTENTION ASSIST Important safety notes G WARNING ATTENTION ASSIST is only an aid and may detect your tiredness or lapses in concentration too late or not at all. It is not a substitute for a well-rested and attentive driver. Fatigue may cause you to recognize hazardous situations too late, misjudge a situation or react more slowly. For this reason, make sure you feel rested before you begin driving and during your journey. Make sure that you take regular breaks in time, particularly on long journeys. Otherwise, you may fail to recognize dangers in time, cause an accident and injure yourself and others.
General notes ATTENTION ASSIST helps you during long, monotonous journeys such as on freeways and interstate highways. It is active in the range between 50 mph (80 km/h) and 112 mph (180 km/h). If ATTENTION ASSIST detects typical indicators of fatigue or increasing lapses in concentration on the part of the driver, it suggests you take a break.
ATTENTION ASSIST assesses your level of fatigue or lapses in concentration by taking the following criteria into account: Ryour personal driving style, e.g. steering
characteristics
Rdriving conditions, e.g. time, driving time The functionality of ATTENTION ASSIST is restricted and warnings may be delayed or not occur at all: Rif the road condition is poor, e.g. if the
surface is uneven or if there are potholes
Rif there is a strong side wind Rif you have adopted a sporty driving style with high cornering speeds or high rates of acceleration
Rif you are predominantly driving slower than 50 mph (80 km/h) or faster than 112 mph (180 km/h)
Rif you are currently using COMAND or
making a telephone call with it
Rif the time has been set incorrectly Rin active driving situations, such as when you change lanes or change your speed
Warning and display messages in the multifunction display
If ATTENTION ASSIST is active, you will be warned no sooner than 20 minutes after your journey has begun. You then hear an intermittent warning tone twice and the Attention Assist: Take a Break! message appears in the multifunction display.
Driving systems
211
X Activate ATTENTION ASSIST using the on-
board computer (Y page 237). Symbol : appears in the multifunction display.
X If necessary, take a break. X Press the a button to confirm the
message.
On long journeys, take regular breaks in good time to allow yourself to rest properly. If you do not take a break, you will be warned again after 15 minutes at the earliest. The precondition for this is that ATTENTION ASSIST still detects typical indicators of fatigue or increasing lapses in concentration. ATTENTION ASSIST is reset when you continue your journey and starts assessing your tiredness again if: Ryou switch off the engine. Ryou take off your seat belt and open the
driver's door, e.g. for a change of drivers or to take a break.
Night View Assist Plus Important safety notes G WARNING Night View Assist Plus is only an aid designed to assist driving. It is not a substitute for attentive driving. Do not rely solely on the Night View Assist Plus display. Continue to look through the windshield. You are responsible for safety and must drive in accordance with traffic conditions. You could otherwise put yourself and others in danger. The system may be impaired or unavailable if: Rthere is poor visibility, e.g. due to snow,
rain, fog or heavy spray.
Rthe windshield is dirty, fogged up or
covered, for instance by a sticker, in the vicinity of the camera.
Ryou are driving on bends, uphill gradients
or downhill gradients.
G WARNING The Night View Assist Plus cannot record objects immediately in front of or next to the vehicle. When maneuvering, continue to look through the windshield. Make sure no persons or animals are in the area in which you are maneuvering. You could otherwise injure them.
In addition to the illumination provided by the normal headlamps, Night View Assist Plus uses infrared light to illuminate the road. Night View Assist Plus camera : picks up the infrared light and displays a monochrome image in COMAND. The image displayed in COMAND corresponds to a road lit up by high- beam headlamps. This enables you to see the road's course and any obstacles in good time. If pedestrian recognition is activated, pedestrians recognized by the system are highlighted in the Night View Assist Plus display. Light from the headlamps of oncoming vehicles does not affect the Night View Assist Plus display in the multifunction display. This is also the case if you cannot switch on the high-beam headlamps due to oncoming traffic. i Infrared light is not visible to the human
eye and therefore does not glare. Night View Assist Plus can therefore remain switched on even if there is oncoming traffic.
212 Driving systems
Switching on Night View Assist Plus Activation conditions You can only activate Night View Assist Plus if: Rthe SmartKey is in position 2 in the ignition
lock.
Rit is dark. Rthe light switch is in the à or L
position.
Rreverse gear has not been engaged. Switching on Night View Assist Plus
X Make sure that COMAND is switched on. X Press button :.
The Night View Assist Plus display appears in the COMAND display.
You can read about how to adjust the brightness of the COMAND display in the COMAND operating instructions. i The infrared lamps switch on
automatically from a speed of about 6 mph (10 km/h). This means that you do not have the full visual range while the vehicle is stationary and cannot check whether Night View Assist Plus is working.
Pedestrian recognition G WARNING Pedestrian recognition may be impaired or inoperative if: Rpedestrians are partially or entirely
obscured by objects, e.g. parked vehicles. Rthe silhouette of the pedestrian in the Night
View Assist Plus display is incomplete or interrupted, e.g. by powerful light reflections.
Rpedestrians do not contrast with the
surroundings.
Rpedestrians are not standing upright, for example, if they are sitting, crouching or lying down.
: Night View Assist Plus display ; Pedestrian recognized = Framing ? Symbol for active pedestrian recognition i Animals are not recognized by pedestrian
recognition.
Night View Assist Plus is able to recognize pedestrians by typical characteristics, e.g. a silhouette in the shape of a person. Pedestrian recognition is then switched on automatically if: RNight View Assist Plus is activated. Ryou are driving faster than 6 mph
(10 km/h).
Rthe surroundings are dark, e.g. when driving outside built-up areas without street lighting.
Driving systems
213
If pedestrian recognition is active, symbol ? appears. If a pedestrian is now recognized, they are framed = and thereby highlighted. If the pedestrian recognition system has brought a pedestrian to your attention, look through the windshield to evaluate the situation. The actual distance to objects and pedestrians cannot be gauged accurately by looking at a screen. It may be the case that objects are highlighted as well as pedestrians.
Fogged up or dirty windshield G WARNING Always remember that you must concentrate primarily on driving the vehicle. A driver's attention to the road must always be his/her primary focus when driving. For your safety and the safety of others: stop the vehicle before attempting to clean fogged up windows or the windshield area in front of the Night View Assist Plus camera. Please remember that when your vehicle is traveling at a speed of only 30 mph (approximately 50 km/h) it covers a distance of 44 ft (approximately 14 m) per second.
If the windshield in front of the camera is fogged up or dirty on the inside or outside, the Night View Assist Plus display is affected. X To defrost: check the automatic air
conditioning settings (Y page 146) and fold down the camera cover (Y page 338).
X To defrost the inside of the windshield: fold down the camera cover (Y page 338) and clean the windshield (Y page 336).
214 Driving systems
Problems with Night View Assist Plus
Problem The picture quality of Night View Assist Plus has deteriorated.
Possible causes/consequences and M Solutions The windshield wipers are smearing the windshield. X Replace the wiper blades (Y page 134). The windshield is smeared after the vehicle has been cleaned in a car wash. X Clean the windshield (Y page 336). There is windshield chip damage in the camera's field of vision. X Replace the windshield. The windshield is fogged up on the inside. X Defrost the windshield (Y page 146). The windshield is iced up. X De-ice the windshield (Y page 145). There is dirt on the inside of the windshield. X Clean the inside of the windshield (Y page 336).
Lane Tracking package General notes The Lane Tracking package consists of Blind Spot Assist (Y page 214) and Lane Keeping Assist (Y page 216).
rain or mist, for example. In this case, vehicles are detected late or not at all. Always pay attention to traffic conditions and your surroundings. Otherwise, you may fail to recognize dangers in time, cause an accident and injure yourself and others.
Blind Spot Assist Important safety notes G WARNING Blind Spot Assist is only an aid designed to assist driving. It may fail to detect some vehicles and is no substitute for attentive driving. Blind Spot Assist cannot detect road and traffic conditions. It may fail to detect narrow vehicles, such as motorcycles or bicycles, or may only detect them too late. Monitoring may be affected by dirty sensors, strong spray or poor visibility caused by snow,
i USA only:
This device has been approved by the FCC as a “Vehicular Radar System”. The radar sensor is intended for use in an automotive radar system only. Removal, tampering, or altering of the device will void any warranties, and is not permitted by the FCC. Do not tamper with, alter, or use in any non-approved way. Any unauthorized modification to this device could void the user’s authority to operate the equipment.
Driving systems
215
General notes Blind Spot Assist uses a radar sensor system to monitor the areas on both sides of your vehicle. It supports you from speeds of approximately 20 mph (30 km/h). A warning display in the exterior mirrors draws your attention to vehicles detected in the monitored area. If you then switch on the corresponding turn signal to change lane, you will also receive an optical and audible collision warning. Blind Spot Assist uses sensors in the rear bumper for monitoring purposes. For Blind Spot Assist to assist you when driving, the radar sensor system must be activated (Y page 241) and operational. Monitoring range of the sensors G WARNING Blind Spot Assist monitors certain areas in the immediate vicinity of your vehicle. Vehicles that approach and drive past at high speeds are not detected. There is no display and no warning. If the lanes are very wide, it may not be possible to monitor the complete width of the neighboring lane. For this reason, vehicles in the next lane may not be detected, especially if they are driving in a staggered formation. This may be the case if vehicles are driving at that edge of their lane which is furthest away from your vehicle. Always pay attention to traffic conditions and your surroundings. Otherwise, you may fail to recognize dangers in time, cause an accident and injure yourself and others.
Example: Sedan The Blind Spot Assist monitors the area up to 3.0 m behind your vehicle and directly next to your vehicle, as shown in the diagram. If the lanes are narrow, vehicles driving in the lane beyond the lane next to your vehicle may be indicated, especially if the vehicles are not driving in the middle of their lane. This may be the case if there are vehicles driving at the inner edge of their lanes. Due to the nature of the system: Rwarnings may be issued in error when
driving close to crash barriers or similar solid lane borders.
Rwarnings may be interrupted when driving
alongside long vehicles, for example lorries, for a prolonged time.
The two radar sensors for Blind Spot Assist are integrated into the sides of the rear bumper. Make sure that the bumper is free from dirt, ice or slush around the sensors. The sensors must not be covered, for example by cycle racks or overhanging loads. Following a severe impact or in the event of damage to the bumpers, have the function of the sensors checked at a qualified specialist workshop. Blind Spot Assist may otherwise not work properly.
216 Driving systems
Indicator and warning display G WARNING Blind Spot Assist is not active at speeds below approximately 20 mph (30 km/h). The indicator lamps in the exterior mirrors are yellow. Vehicles in the monitoring range are then not indicated. Always pay attention to traffic conditions and your surroundings. Otherwise, you may fail to recognize dangers in time, cause an accident and injure yourself and others.
Collision warning If a vehicle is detected in the monitoring range of Blind Spot Assist and you switch on the corresponding turn signal, a double warning tone sounds. Red warning lamp : flashes. If the turn signal remains on, detected vehicles are indicated by the flashing of red warning lamp :. There are no further warning tones. Switching on Blind Spot Assist X Make sure that the radar sensor system
(Y page 241) and Blind Spot Assist (Y page 237) are activated in the on-board computer.
X Turn the SmartKey to position 2 in the
ignition lock. Warning lamps : light up red in the exterior mirrors for approximately 1.5 seconds and then turn yellow.
: Yellow indicator lamp/red warning lamp When Blind Spot Assist is activated, indicator lamp : in the exterior mirrors lights up yellow at speeds of up to 20 mph (30 km/h). At speeds above 20 mph (30 km/h), the indicator lamp goes out and Blind Spot Assist is operational. If a vehicle is detected within the monitoring range of Blind Spot Assist at speeds above 20 mph (30km/h), warning lamp : on the corresponding side lights up red. This warning is always emitted when a vehicle enters the blind spot monitoring range from behind or from the side. When you overtake a vehicle, the warning only occurs if the difference in speed is less than 7 mph (12km/h). The yellow indicator lamp goes out if reverse gear is engaged. In this event, Blind Spot Assist is no longer active. The brightness of the indicator/warning lamps is adjusted automatically according to the ambient light.
Lane Keeping Assist Important safety notes G WARNING Lane Keeping Assist does not keep your vehicle in its lane. It is only an aid and may detect the lane markings on the road incorrectly or not at all. The system may be impaired or may not function if: Rthere is poor visibility, e.g. due to
insufficient illumination of the road, or due to snow, rain, fog or spray.
Rthere is glare, e.g. from oncoming traffic, the sun, or reflection from other vehicles.
Rthe windshield is dirty, fogged up or
covered, for instance by a sticker, in the vicinity of the camera.
Rseveral or no lane markings for a single lane
are present.
Rthe lane markings are worn away, dark or
covered up, e.g. by dirt or snow.
Rthe distance to the vehicle in front is too
small and the lane markings thus cannot be detected.
Rthe lane markings on the road are unclear,
e.g. near roadworks.
Rthe lane markings change quickly, e.g. lanes branch off, cross one another or merge.
Rthe road is narrow and winding. Lane Keeping Assist cannot detect road and traffic conditions. It is not a substitute for attentive driving. You are responsible for the vehicle's speed, braking in good time, and steering correctly. Always adapt your driving style to suit the prevailing road and weather conditions. Always pay attention to traffic conditions and your surroundings. Otherwise, you may fail to recognize dangers in time, cause an accident and injure yourself and others.
General notes
Lane Keeping Assist monitors the area in front of your vehicle by means of a camera : at the top of the windshield. Lane Keeping Assist detects lane markings on the road and warns you before you leave your lane unintentionally. If you have selected km as the display unit in the Display Unit Speed-/ Odometer(Y page 238) function in the on- board computer, Lane Keeping Assist assists you at speeds above 60 km/h. If miles is selected as the display unit, the assistance range starts at 40 mph. A warning may be given if a front wheel passes over a lane marking. It will warn you
Driving systems
217
by means of intermittent vibration in the steering wheel for up to 1.5 seconds. Switching on Lane Keeping Assist
X Switch on Active Lane Keeping Assist using the on-board computer; to do so, select Standard or Adaptive(Y page 237). Symbol : appears in the multifunction display. If your speed exceeds 40 mph (60 km/h) and lane markings are detected, symbol : is highlighted. Lane Keeping Assist is ready for use.
Standard If Standard is selected, no warning vibration occurs if: Ryou switch on the turn signals. In this event, the warnings are suppressed for a certain period of time.
Ra driving safety system intervenes, such as
ABS, BAS or ESP®. Adaptive If Adaptive is selected, no warning vibration occurs if: Ryou switch on the turn signals. In this event, the warnings are suppressed for a certain period of time.
Ra driving safety system intervenes, e.g.
ABS, BAS or ESP®.
Ryou accelerate hard, e.g. kickdown. Ryou brake hard. Ryou steer actively, e.g. swerve to avoid an
obstacle or change lane quickly.
Ryou cut the corner on a sharp bend. In order that you are warned only when necessary and in good time if you cross the
218 Driving systems
lane marking, the system recognizes certain conditions and warns you accordingly. The warning vibration occurs earlier if: Ryou approach the outer lane marking on a
bend.
Rthe road has very wide lanes, e.g. a
freeway.
Rthe system recognizes solid lane markings. The warning vibration occurs later if: Rthe road has narrow lanes. Ryou cut the corner on a bend.
Active Driving Assistance package General notes The Active Driving Assistance package consists of DISTRONIC PLUS (Y page 185), Active Blind Spot Assist (Y page 218) and Active Lane Keeping Assist (Y page 222).
Active Blind Spot Assist Important safety notes G WARNING Active Blind Spot Assist is only an aid, and may detect vehicles/obstacles incorrectly or not at all. The system may be impaired or may not function if: Rthere is poor visibility, e.g. due to snow,
rain, fog or spray.
Rthe rear and/or front sensors are dirty. Active Blind Spot Assist may not detect narrow vehicles, such as motorcycles or bicycles, or may only detect them too late. It cannot detect vehicles that are overtaken at a small distance and then enter the blind spot area. Active Blind Spot Assist cannot detect road and traffic conditions. It is not a substitute for attentive driving. You are responsible for the vehicle's speed, braking in good time, and steering correctly. Always adapt your driving
style to suit the prevailing road and weather conditions. Always pay attention to traffic conditions and your surroundings. Otherwise, you may fail to recognize dangers in time, cause an accident and injure yourself and others.
i USA only:
This device has been approved by the FCC as a “Vehicular Radar System”. The radar sensor is intended for use in an automotive radar system only. Removal, tampering, or altering of the device will void any warranties, and is not permitted by the FCC. Do not tamper with, alter, or use in any non-approved way. Any unauthorized modification to this device could void the user’s authority to operate the equipment.
i Canada only: This device complies with RSS-210 of Industry Canada. Operation is subject to the following two conditions: 1. This device may not cause interference, and 2. this device must accept any interference received, including interference that may cause undesired operation of the device. Removal, tampering, or altering of the device will void any warranties and is not permitted. Do not tamper with, alter, or use the device in any non-approved way. Any unauthorized modification to this device could void the user's authority to operate the equipment.
General notes Active Blind Spot Assist uses a radar sensor system to monitor the side areas of your vehicle which are in back of the driver. A warning display in the exterior mirrors draws your attention to vehicles detected in the monitored area. If you then switch on the corresponding turn signal to change lane, you will also receive an optical and audible warning. If a risk of lateral collision is detected, corrective braking may help you
Driving systems
219
avoid a collision. To support the course- correcting brake application, Active Blind Spot Assist uses the forward-facing radar sensor system. The free space in the direction of travel is then evaluated. Active Blind Spot Assist supports you from a speed of approximately 20 mph(30 km/h). For Active Blind Spot Assist to assist you when driving, the radar sensor system must be activated (Y page 241) and operational. Monitoring area G WARNING Active Blind Spot Assist monitors certain areas in the immediate vicinity of your vehicle. Vehicles that approach and drive past at high speeds are not detected. No visual nor audible warnings are emitted and the system does not brake the vehicle to correct your course. If the lanes are very wide, it may not be possible to monitor the complete width of the neighboring lane. For this reason, vehicles in the next lane may not be detected, especially if they are driving in a staggered formation. This may be the case if vehicles are driving at that edge of their lane which is furthest away from your vehicle. Always pay attention to traffic conditions and your surroundings. Otherwise, you may fail to recognize dangers in time, cause an accident and injure yourself and others.
Example: Sedan Active Blind Spot Assist monitors the area up to 10 ft (3.0m) behind your vehicle and directly next to your vehicle, as shown in the diagram. For this purpose, Active Blind Spot Assist uses radar sensors in the rear bumper. If the lanes are narrow, vehicles driving in the lane beyond the lane next to your vehicle may be indicated, especially if the vehicles are not driving in the middle of their lane. This may be the case if there are vehicles at the inner edge of your lane. Due to the nature of the system: Rwarnings may be issued in error when
driving close to crash barriers or similar solid lane borders.
Rwarnings may be interrupted when driving
alongside long vehicles, for example lorries, for a prolonged time.
The Active Blind Spot Assist radar sensors are integrated into the front and rear bumpers and behind a cover in the radiator grill. Make sure that the bumpers and the cover in the radiator grill are free of dirt, ice or slush. The rear sensors must not be covered, for example by cycle racks or overhanging cargo. Following a severe impact or in the event of damage to the bumpers, have the function of the radar sensors checked at a qualified
220 Driving systems
specialist workshop. Active Blind Spot Assist may otherwise no longer work properly. Indicator and warning display G WARNING Active Blind Spot Assist is not active at speeds below 20 mph (30km/h). The indicator lamps in the exterior mirrors are yellow. Vehicles in the monitoring range are then not indicated. Always pay attention to traffic conditions and your surroundings. Otherwise, you may fail to recognize dangers in time, cause an accident and injure yourself and others.
: Yellow indicator lamp/red warning lamp When Active Blind Spot Assist is activated, indicator lamp : in the exterior mirrors lights up yellow at speeds of up to 20 mph(30km/h). At speeds above 20 mph(30 km/h), the indicator lamp goes out and Active Blind Spot Assist is operational. If a vehicle is detected within the monitoring range of Blind Spot Assist at speeds above 20 mph(30 km/h), warning lamp : on the corresponding side lights up red. This warning is always given when a vehicle enters the blind spot monitoring range from behind or from the side. When you overtake a vehicle, the warning only occurs if the difference in speed is less than 7 mph(12 km/h). The yellow indicator lamp goes out if reverse gear is engaged. In this event, Active Blind Spot Assist is no longer active.
The brightness of the indicator/warning lamps is adjusted automatically according to the ambient light. Visual and audible collision warnings When you switch on the turn signals to change lanes and a vehicle is detected in the side monitoring range, you receive a visual and acoustic collision warning. You then hear a double warning tone and red warning lamp : flashes. If the turn signal remains on, detected vehicles are indicated by the flashing of red warning lamp :. There are no further warning tones. Course-correcting brake application G WARNING Active Blind Spot Assist is only an aid designed to assist driving. It is not a substitute for attentive driving. In some cases, the course-correcting brake application is not sufficient to avoid a collision. In such a case, you must steer, brake or accelerate. In very rare cases, the system may erroneously detect a danger of collision in the area of crash barriers or similar lane borders and apply the brakes. Active Blind Spot Assist does not detect all traffic situations and road users. Always make sure that there is sufficient distance on the side for other traffic or obstacles. An inappropriate brake application may be interrupted at any time if you steer slightly in the opposite direction or accelerate. You are responsible for driving at appropriate speeds, braking in good time, and steering correctly. Always adapt your driving style to suit the prevailing road and weather conditions. Always pay attention to traffic conditions and your surroundings. Otherwise, you may fail to recognize dangers in time, cause an accident and injure yourself and others.
Driving systems
221
RESP® is switched off. Ra loss of tire pressure or a defective tire is
detected.
Switching on Active Blind Spot Assist X Make sure that the radar sensor system (Y page 241) and Active Blind Spot Assist (Y page 237) are activated in the on-board computer.
X Turn the SmartKey to position 2 in the
ignition lock. Warning lamps : in the exterior mirrors light up red for approximately 1.5 seconds and then turn yellow.
If Active Blind Spot Assist detects a risk of a lateral collision in the monitoring range, a course-correcting brake application is carried out. This is meant to assist you in avoiding a collision. If a course-correcting brake application occurs, red warning lamp : flashes in the exterior mirror and a dual warning tone sounds. The display shown in the illustration also appears in the multifunction display. The course-correcting brake application is available in the speed range between 20 mph(30 km/h) and120 mph(200 km/h). Either no braking application, or a course- correcting brake application adapted to the driving situation occurs, if: Rthere are vehicles or obstacles, e.g. crash
barriers, located on both sides of your vehicle.
Ra vehicle approaches you too closely at the
side.
Ryou have adopted a sporty driving style with
high cornering speeds.
Ryou clearly brake or accelerate. Ra driving safety system intervenes, e.g.
ESP® or PRE-SAFE® Brake.
Active Lane Keeping Assist Important safety notes G WARNING Active Lane Keeping Assist does not keep your vehicle in its lane. It is only an aid and may detect the lane markings on the road incorrectly or not at all. The system may be impaired or may not function if: Rthere is poor visibility, e.g. due to
inadequate illumination of the road surface, snow, rain, fog or spray.
Rthere is glare, e.g. from oncoming traffic, the sun, or reflection from other vehicles.
Rthe windshield is dirty, fogged up or
covered, for instance by a sticker, in the vicinity of the camera.
Rseveral or no lane markings for a single lane
are present.
Rthe lane markings are worn away, dark or
covered up, e.g. by dirt or snow.
Rthe distance to the vehicle in front is too small, and as a result the lane markings cannot be recognized.
Rthe lane markings on the road are unclear,
e.g. near roadworks.
222 Driving systems
Rthe lane markings change quickly, e.g.
branch off, cross or merge.
Rthe road is narrow and winding. Active Lane Keeping Assist cannot detect road and traffic conditions. It is not a substitute for attentive driving. You are responsible for the vehicle's speed, braking in good time and steering correctly. Always adapt your driving style to suit the prevailing road and weather conditions. Always pay attention to traffic conditions and your surroundings. Otherwise, you may fail to recognize dangers in time, cause an accident and injure yourself and others.
General notes
Active Lane Keeping Assist monitors the area in front of your vehicle by means of a camera : at the top of the windshield. Active Lane Keeping Assist detects lane markings on the road and warns you before you leave your lane unintentionally. If you do not react to the warning, a lane-correcting application of the brakes can bring the vehicle back into the original lane. In the Display Unit Speed-/Odometer: on-board computer function (Y page 238), if you select the km display unit, Active Lane- Keeping Assist is activated at a speed of 60 km/h. If the Miles display unit is selected, the assistance range begins at 40 mph. Warning vibration in the steering wheel A warning may be given if a front wheel passes over a lane marking. It will warn you
by means of intermittent vibration in the steering wheel for up to 1.5 seconds. In order that you are warned only when necessary and in good time if you cross the lane marking, the system recognizes certain conditions and warns you accordingly. The warning vibration occurs earlier if: Ryou approach the outer lane marking on a
bend.
Rthe road has very wide lanes, e.g. a
freeway.
Rthe system recognizes solid lane markings. The warning vibration occurs later if: Rthe road has narrow lanes. Ryou cut the corner on a bend. Lane-correcting brake application G WARNING Active Lane Keeping Assist does not keep your vehicle in its lane. It is only an aid designed to assist driving. It is not a substitute for attentive driving. In some cases, the lane- correcting brake application is not sufficient to bring your vehicle back to the original lane. In such cases, you must steer the vehicle yourself to ensure that it does not leave the lane. Active Lane Keeping Assist does not detect road and traffic conditions. Always make sure that there is sufficient distance to the side for other traffic or obstacles. In rare cases, unclear markings or particular structures on the roadway can be recognized as solid lane markings. An inappropriate brake application, e.g. after intentionally driving over a solid lane marking, may be interrupted at any time by steering slightly in the opposite direction. Active Lane Keeping Assist cannot take weather conditions into account. You are responsible for the driving at appropriate speeds, braking in good time, and steering correctly. Always adapt your driving style to suit the prevailing road and weather conditions. Always pay attention to traffic conditions and your surroundings. Otherwise,
you may fail to recognize dangers in time, cause an accident and injure yourself and others.
If a lane-correcting brake application occurs, the display shown in the illustration appears in the multifunction display. If you leave your lane under certain circumstances the vehicle will brake briefly on one side. This is meant to assist you in bringing the vehicle back to the original lane. This function is available in the range between 40 mph and 120 mph (60 km/h and 200 km/h). A lane-correcting brake application can only be made after driving over a solid, recognizable lane marking. Before this, a warning must be given by means of intermittent vibration in the steering wheel. In addition, a lane with lane markings on both sides must be recognized. The brake application also slightly reduces vehicle speed. i A further lane-correcting brake
application can only occur after your vehicle has returned to the original lane. No lane-correcting brake application occurs if: Ryou clearly and actively steer, brake or
accelerate.
Ryou cut the corner on a sharp bend. Ryou have switched on the turn signals. Ra driving safety system intervenes, e.g. ESP®, PRE-SAFE® Brake or Active Blind Spot Assist.
Ryou have adopted a sporty driving style with
high cornering speeds or high rates of acceleration.
Driving systems
223
RESP® is switched off. Rthe transmission is not in position D. Ra loss of tire pressure or a defective tire has
been detected and displayed.
Active Lane Keeping Assist does not detect traffic situations or road users. An inappropriate brake application may be interrupted at any time if you: Rsteer slightly in the opposite direction. Ruse a turn signal. Rclearly brake or accelerate. A lane-correcting brake application is interrupted automatically if: Ra driving safety system intervenes, e.g. ESP®, PRE-SAFE® Brake or Active Blind Spot Assist.
Rlane markings can no longer be recognized. Switching on Active Lane Keeping Assist
X Switch on Active Lane Keeping Assist using the on-board computer; to do so, select Standard or Adaptive(Y page 237). Symbol : appears in the multifunction display. If your speed exceeds 40 mph (60 km/h) and lane markings are detected, symbol : is highlighted. Active Lane Keeping Assist is ready for use. If Standard is selected, no warning vibration occurs if: Ryou have switched on the turn signals. In this event, the warnings are suppressed for a certain period of time.
Ra driving safety system intervenes, such as ABS, BAS or ESP®. If Adaptive is selected, no warning vibration occurs if:
224 Driving systems
Ryou have switched on the turn signals. In this event, the warnings are suppressed for a certain period of time.
Ra driving safety system intervenes, e.g.
ABS, BAS or ESP®.
Ryou accelerate hard, e.g. kickdown. Ryou brake hard. Ryou steer actively, e.g. swerve to avoid
an obstacle or change lane quickly. Ryou cut the corner on a sharp bend.
Useful information ............................ 226
Important safety notes .................... 226
Displays and operation .................... 227
Menus and submenus ...................... 230
Display messages ............................. 246
Indicator and warning lamps in the instrument cluster ............................ 275225
226
Important safety notes
Useful information
i This Operator's Manual describes all models and all standard and optional equipment of your vehicle available at the time of publication of the Operator's Manual. Country-specific differences are possible. Please note that your vehicle may not be equipped with all features described. This also applies to safety- related systems and functions.
i Read the information on qualified specialist workshops: (Y page 25).
Important safety notes
G WARNING The driver's concentration must always be directed primarily at road traffic. For your safety and the safety of others, selecting features through the multifunction steering wheel should only be done by the driver when traffic and road conditions permit it to be done safely. Bear in mind that at a speed of only 30 mph (approximately 50 km/h), the vehicle covers a distance of 44 feet (approximately 14 m) per second. G WARNING No messages will be displayed if either the instrument cluster or the multifunction display is inoperative. As a result, you will not be able to see information about your driving conditions, such as Rspeed Routside temperature Rwarning/indicator lamps Rmalfunction/warning messages Rfailure of any systems Driving characteristics may be impaired.
If you must continue to drive, do so with added caution. Contact an authorized Mercedes- Benz Center as soon as possible. G WARNING Malfunction and warning messages are only displayed for certain systems and are intentionally not very detailed. The malfunction and warning messages are simply a reminder with respect to the operation of certain systems. They do not replace the owner's and/or driver's responsibility to maintain the vehicle's operating safety. Have all required maintenance services and safety checks performed on the vehicle. Bring the vehicle to an authorized Mercedes-Benz Center to address the malfunction and warning messages. G WARNING All categories of messages contain important information which should be taken note of and, where a malfunction is indicated, addressed as soon as possible at an authorized Mercedes-Benz Center. Failure to repair the condition noted may cause damage not covered by the Mercedes- Benz Limited Warranty, or result in property damage or personal injury. G WARNING HYBRID vehicles: It is imperative that you read the HYBRID Supplemental Operating Instructions included in your vehicle literature portfolio. You may otherwise not receive all necessary safety information and warning for the operation of your vehicle.
For an illustration of the instrument cluster, see (Y page 31).
Displays and operation 227
Displays and operation Instrument cluster
: Fuel gauge ; Time = Speedometer with segments (Y page 228) ? Multifunction display (Y page 230) A Tachometer (Y page 228) B Coolant temperature (Y page 227) C Instrument cluster lighting (Y page 227) i You can set the time using COMAND; see the separate Operating Instructions.
Instrument lighting The lighting in the instrument cluster, in the displays and the controls in the vehicle interior can be adjusted using the brightness control knob. The brightness control knob is located on the bottom left of the instrument cluster (Y page 31). X Turn the brightness control knob clockwise
or counter-clockwise. If the light switch is set to Ã, T or L, the brightness is dependent upon the brightness of the ambient light.
i The light sensor in the instrument cluster
automatically controls the brightness of the multifunction display. In daylight, the displays in the instrument cluster are not illuminated.
Coolant temperature display G WARNING Driving when your engine is overheated can cause some fluids which may have leaked into the engine compartment to catch fire. You could be seriously burned.
228 Displays and operation
Steam from an overheated engine can cause serious burns which can occur just by opening the engine hood. Stay away from the engine if you see or hear steam coming from it. Stop the vehicle in a safe location away from other traffic. Turn off the engine, get out of the vehicle and do not stand near the vehicle until the engine has cooled down.
! A display message is shown if the coolant
temperature is too high. If the coolant temperature is over 248 ‡(120 †), do not continue driving. The engine will otherwise be damaged.
The coolant temperature gauge is in the instrument cluster on the right-hand side (Y page 31). Under normal operating conditions and with the specified coolant level, the coolant temperature may rise to 248 ‡ (120 †).
Tachometer ! Do not drive in the overrevving range, as
this could damage the engine.
The red band in the tachometer indicates the engine's overrevving range. The fuel supply is interrupted to protect the engine when the red band is reached.
Outside temperature display G WARNING The outside temperature indicator is not designed to serve as an ice-warning device and is therefore unsuitable for that purpose. Indicated temperatures just above the freezing point do not guarantee that the road surface is free of ice. The road may still be icy, especially in wooded areas or on bridges.
The outside temperature display is in the multifunction display (Y page 230). Changes in the outside temperature are displayed after a short delay.
Speedometer with segments The segments in the speedometer indicate which speed range is available. RCruise control activated (Y page 183): The segments light up from the stored speed to the maximum speed.
RDISTRONIC PLUS activated (Y page 185):
One or two segments in the set speed range light up.
RDISTRONIC PLUS detects a vehicle in front:
The segments between the speed of the vehicle in front and the stored speed light up.
Operating the on-board computer Overview
: Multifunction display ; Right control panel = Switches on the Voice Control System; see the separate operating instructions
? Back button A Left control panel X To activate the on-board computer: turn the SmartKey to position 1 in the ignition lock.
Displays and operation 229
You can control the multifunction display and the settings in the on-board computer using the buttons on the multifunction steering wheel.
Left control panel
Right control panel
~ RRejects or ends a call
RExits phone book/redial
memory
6 RMakes or accepts a call
RSwitches to the redial memory RAdjusts the volume
8 RMute
Back button
% Press briefly:
RBack RSwitches off the Voice Control
System; see the separate operating instructions RHides display messages/calls up the last Trip menu function used
RExits the telephone book/redial
memory
% Press and hold: RCalls up the standard display in the Trip menu
RCalls up the menu and menu bar
Press briefly: RScrolls in lists RSelects a submenu or function RIn the Audio menu: selects a stored station, an audio track or a video scene RIn the Tel (telephone) menu: switches to the phone book and selects a name or telephone number
Press and hold: RIn the Audio menu: selects the previous/next station or selects an audio track or a video scene using rapid scrolling RIn the Tel (Telephone) menu: starts rapid scrolling if the phone book is open
a RConfirms a selection/display message RIn the Tel (telephone) menu: switches to the telephone book and starts dialing the selected number RIn the Audio menu: stops the station search function at the desired station
230 Menus and submenus
Multifunction display
Example: multifunction display for DIRECT SELECT automatic transmission : Description field ; Menu bar = Drive program (Y page 162) ? Transmission position (Y page 161) A Permanent display: outside temperature
or speed (Y page 238)
X To show menu bar ;: press the = or ; button on the steering wheel.
Menu bar ; disappears after a few seconds. Text field : shows the selected menu or submenu as well as display messages. The following messages may appear in the multifunction display: XjY CRUISE Cruise control (Y page 183) _ Adaptive Highbeam Assist
Parking Guidance (Y page 205)
À ATTENTION ASSIST (Y page 210) ¤ ECO start/stop function
à Lane Keeping Assist (Y page 216) à Active Lane Keeping Assist
(Y page 127)
(Y page 157)
(Y page 221)
ë HOLD function (Y page 196) Ä PRE-SAFE® Brake (Y page 72)
Menus and submenus Menu overview Press the = or ; button on the steering wheel to call up the menu bar and select a menu. Operating the on-board computer (Y page 228). Depending on the equipment installed in the vehicle, you can call up the following menus: RTrip menu (Y page 230) RNavi menu (navigation instructions) (Y page 232) RAudio menu (Y page 233) RTel menu (telephone) (Y page 234) RDriveAssist menu (assistance) (Y page 236) RServ. menu (Y page 238) RSett. menu (Y page 238) RAMG menu in AMG vehicles (Y page 242)
Trip menu Standard display
X Press and hold the % button on the steering wheel until the Trip menu with trip odometer : and odometer ; is shown.
Menus and submenus
