Login- Download PDF Manual
-
Mirror light : only functions if the sun visor is clipped into retainer ; and mirror cover A has been folded up.
Glare from the side
X Fold down the sun visor. X Pull the sun visor out of retainer ;.
X Swing the sun visor to the side.
Rear window roller sunblind
Important safety notes
At temperatures below Ò4 ‡ (Ò20 †), the roller sunblind is deactivated.
Features
445
G WARNING When leaving the vehicle, always remove the SmartKey from the ignition lock. Always take the SmartKey with you and lock the vehicle. Do not leave children unattended in the vehicle, even if they are secured in a child restraint system, or with access to an unlocked vehicle. A child's unsupervised access to a vehicle could result in an accident and/or serious personal injury. The children could:
Rinjure themselves on parts of the vehicle
Rbe seriously or fatally injured through
excessive exposure to extreme heat or cold
Rinjure themselves or cause an accident with
vehicle equipment that can be operated even if the SmartKey is removed from the ignition lock or removed from the vehicle, such as seat adjustment, steering wheel adjustment, or the memory function
If children open a door, they could injure other persons or get out of the vehicle and injure themselves or be injured by following traffic.
Do not expose the child restraint system to direct sunlight. The child restraint system's metal parts, for example, could become very hot, and the child could be burned on these parts.
G WARNING When adjusting a roller sunblind, the roller blind moves up or down. You might become trapped in the process.
In the event of danger, briefly press the button for the roller sunblind to change the roller blind's direction of movement.
Extending/retracting from the driver's
seat
! Make sure that the roller sunblind can
move freely. Otherwise, the roller sunblind or other objects could be damaged.
X To extend or retract: briefly press
button :. The roller sunblind fully extends or fully retracts.
X To stop: briefly press button : again.
The roller sunblind stops briefly and moves back into the out-of-use position.
Extending/retracting from the rear
The switch is located on the rear door control panel.
Extending X Pull switch : up and release it. The roller sunblind extends fully.
X To stop: press switch : down briefly.
The roller sunblind stops briefly and then retracts again.
446 Features
Retracting X Press switch : down past the point of
resistance and release it. The roller sunblind retracts fully.
X To stop: pull switch : up.
The roller sunblind stops briefly and then extends again.
Ashtray
Ashtray in the front-compartment
center console
X To open: slide cover : forwards until it
engages.
X To remove insert: hold insert = by the
ribbing at the sides and lift it up ; and out.
X To re-install the insert: press insert =
into the holder until it engages.
X To close: press cover : briefly at the
front. The cover moves back.
Ashtray in the rear-compartment center
console
X To open: lift up cover ;.
X To remove the insert: press open
cover ; past the stop. Insert : pops out of the holder.
X Lift insert : up and out. X To install the insert: put insert : from
above into the holder and press down into the holder until it engages.
Cigarette lighter
G WARNING When leaving the vehicle, always remove the SmartKey from the ignition lock. Always take the SmartKey with you and lock the vehicle. Do not leave children unattended in the vehicle, even if they are secured in a child restraint system, or with access to an unlocked vehicle. A child's unsupervised access to a vehicle could result in an accident and/or serious personal injury. The children could:
Rinjure themselves on parts of the vehicle
Rbe seriously or fatally injured through
excessive exposure to extreme heat or cold
The ashtrays are located in the rear doors.
Rinjure themselves or cause an accident with
vehicle equipment that can be operated even if the SmartKey is removed from the ignition lock or removed from the vehicle, such as seat adjustment, steering wheel adjustment, or the memory function
Features
447
If children open a door, they could injure other persons or get out of the vehicle and injure themselves or be injured by following traffic.
Do not expose the child restraint system to direct sunlight. The child restraint system's metal parts, for example, could become very hot, and the child could be burned on these parts.
G WARNING Never touch the heating element or sides of the lighter; they are extremely hot. Hold the knob only.
Make sure any children traveling with you do not injure themselves or start a fire with the hot cigarette lighter.
Center console, front
X Turn the SmartKey to position 2 in the
ignition lock.
Center console, rear compartment
X Press in cigarette lighter :.
Cigarette lighter : will pop out automatically when the heating element is red-hot.
12 V sockets
Points to observe before use
The sockets can be used for accessories with a maximum draw of 180 W (15 A). Accessories include such items as lamps or chargers for mobile phones.
If you use the sockets for long periods when the engine is switched off, the battery may discharge.
X Turn the SmartKey to position 1 in the
ignition lock.
X To open: slide cover : forwards until it
i An emergency cut-out ensures that the
engages.
X Press in cigarette lighter ;.
Cigarette lighter ; will pop out automatically when the heating element is red-hot.
X To close: press cover : briefly at the
front. The cover moves back.
on-board voltage does not drop too low. If the on-board voltage is too low, the power to the sockets is automatically cut. This ensures that there is sufficient power to start the engine.
448 Features
Socket in the glove box
115 V socket
G WARNING The 115 V AC power socket operates on high voltage. Use the 115 V AC power socket in the vehicle with the same caution and care that you would take with power sockets at home. Keep fluids away from the 115 V AC power socket. Do not use liquids or sharp tools to clean the power socket. Keep the cover of the 115 V AC power socket closed when not in use. Otherwise, you could suffer an electric shock and be seriously or even fatally injured.
G WARNING Any device that you connect must have a suitable plug and meet U.S. standards. Never pull at a cable to disconnect a plug from a 115 V AC power socket. Never use a damaged connection cable. The 115 V AC power socket must never be connected to another 115 V AC power source. Do not use a converter with an earthed plug for the 115 V AC power socket. This could cause serious injury to you and/or other people.
G WARNING If the 115 V AC power socket is damaged or pulled out of the trim, do not use or touch the 115 V AC power socket. The use of a 115 V AC power socket that has been damaged or pulled out of the trim could cause serious injury to you or others.
X Open the glove box (Y page 438). X Lift up the cover of socket :.
Socket in the rear-compartment center
console
Example: vehicles with the smoker's package
X Lift up the cover of socket :.
Socket in the trunk
X Lift up the cover of socket :.
Features
449
115 V socket : provides an alternating voltage of 115 V, so that small electronic devices can be connected. These devices, such as game consoles, chargers and laptops, together should not consume more than a maximum of 150 W.
Requirements for operation of these devices:
Rthe plug of the electronic device must be inserted fully into 115 V power socket :.
Rthe maximum wattage of the device to be
connected must not exceed 150 W.
Rthe on-board power supply is within a
permissible voltage range.
Rthe 12 V socket in the trunk is operational
(Y page 447). X Open flap =.
X Insert the plug of the electronic device into
115 V power socket :. Indicator lamp ; lights up. If indicator lamp ; does not light up, consult the section on malfunctions.
X To turn off: disconnect the plug from
115 V power socket :.
Ensure that you do not pull on the cord.
Possible causes of malfunction:
Rthe on-board power supply is not within a
permissible voltage range.
Rthe temperature of the DC/AC converter is
temporarily too high.
Rsome small electronic devices have a constant nominal power of less than 150 W, but a very high inrush current. These devices will not work. If you connect such a device, 115 V power socket : will not supply it with power.
If indicator lamp ; still does not light up, contact a specialist workshop.
mbrace
Important safety notes
! You must have a license agreement to activate the mbrace service. Ensure that your system is activated and ready for use, and press the E MB Info call button to register. If one of these steps is not carried out, it may not be possible to activate the system.
If you have questions about the activation, contact one of the following telephone hotlines:
RUSA: Mercedes-Benz Customer
Assistance Center at 1-800-FOR-MERCedes (1-800-367-6372) or 1-866-990-9007
RCanada: Customer Service at
1-888-923-8367
Shortly after successfully registering with the mbrace service, a user ID and password will be sent to you by mail. You can use this password to log in to the mbrace section under "Owners Online" at http:// www.mbusa.com22.
The mbrace system is available if:
Rit has been activated and is operational
Rthe corresponding mobile phone network
is available for transmitting data to the Customer Center
Ra service subscription is available
Rthe starter battery is sufficiently charged
i Determining the location of the vehicle on
a map is only possible if:
RGPS reception is available.
Rthe vehicle position can be forwarded to
the Customer Assistance Center
22 USA only.
450 Features
The mbrace system
The mbrace system provides different services, e.g.:
Rautomatic and manual emergency call
RRoadside Assistance call
RMB Info call
To adjust the volume during an mbrace call, proceed as follows:
X Press the W or X button on the
multifunction steering wheel.
or X Use the H volume controller of
COMAND (Y page 123).
You can find further information and a description of all available features under "Owners Online" at http:// www.mbusa.com23.
System self-test
After you have switched on the ignition, the system carries out a self-diagnosis.
A malfunction in the system has been detected if one of the following occurs:
Rthe indicator lamp in the SOS button does
not come on during the system self-test. Rthe indicator lamp in the º Roadside
Assistance button does not light up during self-diagnosis of the system.
Rthe indicator lamp in the E MB-Info call
button does not light up during self- diagnosis of the system.
Rthe indicator lamp in one or more of the
following buttons continues to light up red after the system self-diagnosis:
- SOS button
the º Roadside Assistance call button the E MB Info call button
Rthe Tele Aid Inoperative or Tele Aid Not Activated message appears in the
23 USA only.
multifunction display after the system self- diagnosis.
If a malfunction is indicated as outlined above, the system may not operate as expected. In the event of an emergency, assistance must be summoned by other means.
Have the system checked at the nearest authorized Mercedes-Benz Center or contact the following service hotlines:
RUSA: Mercedes-Benz Customer Assistance
Center at 1-800-FOR-MERCedes (1-800-367-6372) or 1-866-990-9007
RCanada: Customer Service at
1-888-923-8367
Emergency call
Important safety notes ! You must have a license agreement to activate the mbrace service. Ensure that your system is activated and ready for use, and press the E MB Info call button to register. If one of these steps is not carried out, it may not be possible to activate the system.
If you have questions about the activation, contact one of the following telephone hotlines:
RUSA: Mercedes-Benz Customer
Assistance Center at 1-800-FOR-MERCedes (1-800-367-6372) or 1-866-990-9007
RCanada: Customer Service at
1-888-923-8367
An emergency call is dialed automatically if an air bag or Emergency Tensioning Device is triggered.
i You cannot end an automatically triggered emergency call yourself.
An emergency call can also be initiated manually.
As soon as the emergency call has been initiated, the indicator lamp in the SOS button flashes. The Connecting Call message appears on the multifunction display. Emergency Call Activated is shown in the COMAND display. The audio system is muted.
Once the connection has been made, the Call Connected message appears in the multifunction display. The Emergency Call Activated message is shown in the COMAND display.
All important information on the emergency is transmitted, for example:
Rcurrent location of the vehicle (as
determined by the GPS system)
Rvehicle identification number
Rinformation on the type of emergency
i If the Emergency Call Activated
message is shown in the COMAND display, you cannot use other functions of COMAND.
Shortly after the emergency call has been initiated, a voice connection is automatically established between the Mercedes-Benz Customer Assistance Center and the vehicle occupants. If the vehicle occupants respond, the Mercedes-Benz Customer Assistance Center attempts to get more information on the emergency.
i If there is no response from the vehicle occupants, an ambulance is immediately sent to the vehicle.
G WARNING If the indicator lamp in the SOS button is flashing continuously and there was no voice connection to the Response Center established, then the mbrace system could not initiate an emergency call (e.g. the relevant cellular phone network is not available).
The message Call Failed appears in the multifunction display for approximately 10 seconds.
Features
451
Should this occur, assistance must be summoned by other means.
i During an emergency call, the
Bluetooth® connection on the phone is canceled automatically. After making the emergency call, the connection is automatically re-established.
Making an emergency call
X To initiate an emergency call
manually: press cover : briefly to open.
X Press SOS button ; briefly.
The indicator lamp in SOS button ; flashes until the emergency call is concluded.
X Wait for a voice connection to the
Mercedes-Benz Customer Assistance Center.
X After the emergency call, close cover :.
G WARNING If you feel at any way in jeopardy when in the vehicle (e.g. smoke or fire in the vehicle, vehicle in a dangerous road location), please do not wait for voice contact after you have pressed the SOS button. Carefully leave the vehicle and move to a safe location. The Response Center will automatically contact local emergency officials with the vehicle's approximate location if they receive an automatic SOS signal and cannot make voice contact with the vehicle occupants.
The Mercedes-Benz Customer Assistance Center either sends a qualified Mercedes- Benz technician or organizes for your vehicle to be transported to the nearest authorized Mercedes-Benz Center. You may be charged for services such as repair work and/or towing. Further details are available in your mbrace manual.
i The mbrace system failed to initiate a
Roadside Assistance call if:
Rthe indicator lamp in Roadside
Assistance button : is flashing continuously.
Rno voice connection to the Mercedes- Benz Customer Assistance Center was established.
This may be because the corresponding mobile phone network is not available. The Call Failed message appears in the multifunction display. The COMAND display shows the Call could not be connected! message. Press W to confirm the message.
X To end a call: press the~ button on the
multifunction steering wheel.
or
X Press the corresponding button for ending
a phone call on the COMAND telephone keypad.
MB Info call button
X Open the stowage compartment under the
armrest (Y page 439).
452 Features
Roadside Assistance button
X Open the stowage compartment under the
armrest (Y page 439).
X Press and hold Roadside Assistance
button : for more than two seconds. This initiates a call to the Mercedes-Benz Customer Assistance Center. The indicator lamp in Roadside Assistance button : flashes while the call is active. The Connecting Call message appears in the multifunction display and the COMAND display. The audio output is muted.
If a connection can be established, the Call Connected message appears in the multifunction display and in the COMAND display.
If a cellular phone network is available and there is sufficient GPS reception, the mbrace system transmits data to the Mercedes-Benz Customer Assistance Center, for example:
Rcurrent location of the vehicle
Rvehicle identification number
i The multifunction display and COMAND display show that an mbrace call is active. You can change to the navigation menu by pressing the S button during the call, for example.
Voice output is not available.
A voice connection is established between the Mercedes-Benz Customer Assistance Center and the vehicle occupants.
X Describe the type of assistance needed.
X Press and hold MB Info call button : for
i The mbrace system failed to initiate an
Features
453
more than two seconds. This initiates a call to the Mercedes-Benz Customer Assistance Center. The indicator lamp in MB Info call button : flashes while the connection is being established. The Connecting Call message appears in the multifunction display. The COMAND display shows the Information Call Activated message. The audio output is muted.
If a connection can be established, the Call Connected message appears in the multifunction display.
The COMAND display shows the Information Call Activated message.
If a cellular phone network is available and there is sufficient GPS reception, the mbrace system transmits data to the Mercedes-Benz Customer Assistance Center, for example:
Rcurrent location of the vehicle
Rvehicle identification number
i The COMAND display shows that an
mbrace call is active. You can change to the navigation menu by pressing the S button during the call, for example.
Voice output is not available.
A voice connection is established between the Mercedes-Benz Customer Assistance Center and the vehicle occupants. You can obtain information on how to operate your vehicle's systems, on the location of the nearest authorized Mercedes-Benz Center, and on further products and services offered by Mercedes-Benz USA.
Further details on the mbrace system can be found under http://www.mbusa.com24. Log in under "Owners Online".
MB Info call if:
Rthe indicator lamp in MB Info call
button : is flashing continuously.
Rno voice connection to the Mercedes- Benz Customer Assistance Center was established.
This may be because the corresponding mobile phone network is not available. The Call Failed message appears in the multifunction display. The COMAND display shows the Call could not be connected! message. Press W to confirm the message.
X To end a call: press the~ button on the
multifunction steering wheel.
or
X Press the corresponding button for ending
a phone call on the COMAND telephone keypad.
Call priority
When service calls are active, e.g. Roadside Assistance or MB Info calls, an emergency call can still be initiated. In this case, an emergency call will take priority and override all other active calls.
The indicator lamp of the respective button flashes until the call is ended. An emergency call can only be terminated by the Mercedes- Benz Customer Assistance Center. All other calls can be ended by pressing the ~ button on the multifunction steering wheel or the corresponding button for ending a telephone call on the COMAND telephone keypad.
Downloading destinations in COMAND
i The components and operating principles
of COMAND can be found on (Y page 122).
24 USA only.
Search & Send
Points to observe before use i To use "Search & Send", your vehicle
must be equipped with mbrace and a navigation system. You must also have an mbrace service subscription.
"Search & Send" is a destination entry service. A destination address which is found on Google Maps® can be transferred via mbrace directly to your vehicle's navigation system.
Specifying and sending the destination
address
X Go to the website http://
www.maps.google.com and enter a destination address into the entry field.
X To send the destination address to the
E-Mail address of your mbrace account: click on the corresponding button.
i Example:
If you select 'Send to vehicle' and then 'Mercedes-Benz', the destination address will be sent to your vehicle.
X When the "Send" dialog window appears:
In the relevant field, enter the e-mail address which you specified when activating your mbrace account.
X Click "Send".
i Information on specific commands such
as "Address entry" or "Sending" can be found on the website.
454 Features
i You can only use the Destination Download function if the vehicle is equipped with a navigation system.
Destination Download gives you access to a database with over 15 million points of interest (POIs)/important destinations that can be downloaded onto the navigation system of your vehicle. If you know the destination, you can download the address or obtain the location of points of interest (POIs)/important destinations in the surrounding area.
You are prompted to confirm route guidance to the address entered. X Slide XVY and turn cVd the COMAND controller to select Yes and confirm by pressing W.
The system calculates the route and subsequently starts the route guidance with the address entered.
i If you select No, the address can be stored
in the address book.
i The Destination Download function is
available if the corresponding mobile phone network is available and data transfer is possible.
Route Assistance
This service is part of the mbrace PLUS Package and cannot be purchased separately.
i You can also use the Route Assistance
function if your vehicle is not equipped with a navigation system.
Within the framework of this service, you receive a professional and reliable form of navigation support without having to leave your vehicle.
The customer service representative determines a suitable driving route based on your current vehicle position and the desired destination and guides you live through the current sections of the route.
Calling up destination addresses
X Press the MB Info call button to load the
destination address to your vehicle's navigation system. A display message appears, asking whether navigation should be started. X Select Yes by sliding XVY and turning
cVd the COMAND controller and press W to confirm. The system calculates the route and subsequently starts the route guidance with the address entered.
i If you select No, the address can be stored
in the address book.
i If you have sent more than one
destination address, you have to make an info call to load each individual address.
i Destination addresses are loaded in the same order as the order in which they were sent. If you own multiple Mercedes-Benz vehicles with mbrace and activated mbrace accounts:
Each destination address sent can be accessed by every vehicle which is connected with the relevant e-mail address.
Vehicle remote opening
You can use the vehicle remote opening if you have unintentionally locked your vehicle and a replacement SmartKey is not available. The vehicle can be opened by the Mercedes-Benz Customer Assistance Center.
The vehicle can be opened remotely up to four days after the ignition was last switched off.
X Contact the following service hotlines:
RUSA: Mercedes-Benz Customer
Assistance Center at
Features
455
1-800-FOR-MERCedes (1-800-367-6372) or 1-866-990-9007
RCanada: Customer Service at
1-888-923-8367
You will be asked for your password.
X Return to your vehicle at the time agreed upon with the Mercedes-Benz Customer Assistance Center.
X Pull on the trunk lid handle for at least
20 seconds until the indicator lamp in the SOS button (Y page 450) flashes. The Connecting Call message appears in the multifunction display.
USA only: alternatively, the vehicle can be opened via:
Rthe Internet, under the "Owners Online"
section
Rthe telephone application (e.g. iPhone®)
i Vehicle remote opening is only possible if the corresponding mobile phone network is accessible.
The SOS button flashes and the Connecting Call message appears in the multifunction display to confirm that the command for vehicle remote unlocking has been received.
If the trunk lid handle is pulled for longer than 20 seconds before authorization has been received, you must wait for 15 minutes. Only then can you pull the trunk lid handle once again.
Vehicle remote closing
The remote closing feature can be used when you have forgotten to lock the vehicle and you are no longer nearby. The vehicle can then be locked by the Mercedes-Benz Customer Assistance Center.
The vehicle can be locked remotely up to four days after the ignition was last switched off.
X Contact the following service hotlines:
RUSA: Mercedes-Benz Customer
Assistance Center at
456 Features
1-800-FOR-MERCedes (1-800-367-6372) or 1-866-990-9007
RCanada: Customer Service at
1-888-923-8367
You will be asked for your PIN.
The next time you are in your vehicle and switch on the ignition, the Tele Aid Doors Locked Remotely message appears in the multifunction display.
USA only: alternatively, the vehicle can be locked via:
Rthe Internet, under the "Owners Online"
section
Rthe telephone application (e.g. iPhone®)
i The vehicle remote closing feature is
available when the relevant mobile phone network is available and data connection is possible.
Automatic vehicle data retrieval for the
service due date
Your vehicle comes with a function which improves the servicing of the vehicle considerably. Shortly before the service due date, mbrace sends important vehicle maintenance information to the Mercedes- Benz Customer Assistance Center. The Mercedes-Benz Customer Assistance Center then informs your authorized Mercedes-Benz Service Center of the work required. This happens automatically and does not require any action from the driver. This function allows the Mercedes-Benz Center to improve appointment planning significantly and ensures that your vehicle receives the best service possible.
i The "Automatic retrieval of vehicle data for the service due date" function is only available if the relevant mobile phone network is available and a data connection is possible.
Stolen vehicle recovery service
If your vehicle has been stolen:
X Notify the police.
The police will issue a numbered incident report.
X This number will be forwarded to the Mercedes-Benz Customer Assistance Center together with your PIN. The Mercedes-Benz Customer Assistance Center then attempts to locate the mbrace system. The Mercedes-Benz Customer Assistance Center contacts you and the local law enforcement agency if the vehicle is located. However, only the law enforcement agency is informed of the location of the vehicle.
i If the anti-theft alarm system is active for
longer than 30 seconds, mbrace automatically informs the Mercedes-Benz Customer Assistance Center.
Garage door opener
Important safety notes
G WARNING Before programming the integrated remote control to a garage door opener or gate operator, make sure people and objects are out of the way of the device to prevent potential harm or damage. When programming a garage door opener, the door moves up or down. When programming a gate operator, the gate opens or closes.
Do not use the integrated remote control with any garage door opener that lacks safety stop and reverse features as required by U.S. federal safety standards (this includes any garage door opener model manufactured before April 1, 1982). A garage door that cannot detect an object - signaling the door to stop and reverse - does not meet current U.S. federal safety standards.
When programming a garage door opener, park vehicle outside the garage.
Do not run the engine while programming the integrated remote control. Inhalation of exhaust gas is hazardous to your health. All exhaust gas contains carbon monoxide (CO), and inhaling it can cause unconsciousness and possible death. All exhaust gas contains carbon monoxide (CO), and inhaling it can cause unconsciousness and possible death.
The HomeLink® garage door opener integrated in the rear-view mirror allows you to operate up to three different door and gate systems.
i Certain garage door drives are
incompatible with the integrated garage door opener. If you have difficulty programming the integrated garage door opener, contact an authorized Mercedes- Benz Center.
Alternatively, you can call the following telephone assistance services:
RUSA: Mercedes-Benz Customer
Assistance Center at 1-800-FOR-MERCedes
RCanada: Customer Service at
1-800-387-0100
RHomeLink® hotline 1-800-355-3515
(free of charge)
More information on HomeLink® and/or compatible products is also available online at http://www.homelink.com.
i USA only:
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.
Any unauthorized modification to this device could void the user's authority to operate the equipment.
FCC ID: CB2HMIHL4
Features
457
i Canada only:
This device complies with the RSS-210
Rules of Industry Canada. Operation is subject to the following two conditions:1. This device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation of the device.
Any unauthorized modification to this device could void the user's authority to operate the equipment.
IC: 279B-HMIHL4
Programming the integrated garage
door opener on the rear-view mirror
Programming buttons
G WARNING Only press the button on the integrated garage door opener if there are no persons or objects present within the sweep of the garage door. Persons could otherwise be injured as the door moves.
Integrated garage door opener on the rear-view mirror
Garage door remote control A is not part of the integrated garage door opener.
X Before programming for the first time, clear the memory of the integrated garage door opener (Y page 459).
X Turn the SmartKey to position 2 in the
ignition lock.
458 Features
X Press and hold one of buttons ; to ? on
Synchronizing the rolling code
the integrated garage door opener. After a short time, indicator lamp : lights up yellow.
i Indicator lamp : lights up yellow as soon as button ;, = or ? is programmed for the first time. If the selected button has already been programmed, indicator lamp : will only light up yellow after ten seconds have elapsed.
X Release button ;, = or ?. Indicator
lamp : flashes yellow.
X Point garage door remote control A
towards buttons ; to ? on the rear-view mirror at a distance of 2 to 8 inches (5 to 20 cm).
i The required distance between remote
control A and the integrated garage door opener depends on the garage door drive system. Several attempts might be necessary. You should test every position for at least 25 seconds before trying another position.
X Press and hold button B on remote control A until indicator lamp : lights up green. If indicator lamp : lights up green or flashes, then programming has been successful.
X Release button B on remote control A for
the garage door drive system.
X If indicator lamp : lights up red: repeat
the programming procedure for the corresponding button on the rear-view mirror. When doing so, vary the distance between remote control A and the rear- view mirror.
i If the indicator lamp flashes green after successful programming, the garage door system is using a rolling code. After programming, you must synchronize the garage door opener integrated in the rear- view mirror with the receiver of the garage door system.
Your vehicle must be within reach of the garage door or exterior gate drive. Make sure that neither your vehicle nor any persons/ objects are present within the sweep of the door or gate.
Observe the safety notes when performing the rolling code synchronization (Y page 456).
Observe the safety notes when performing the rolling code synchronization.
X Turn the SmartKey to position 2 in the
ignition lock.
X Press the programming button of the door
or gate drive (see the door or gate drive operating instructions, e.g. under "Programming of additional remote controls").
i Usually, you now have 30seconds to
initiate the next step.
X Press previously programmed button ;,
= or ? of the integrated garage door opener until the door closes. The rolling code synchronization is then complete.
Notes on programming the remote
control
Canadian radio frequency laws require a "break" (or interruption) of the transmission signals after broadcasting for a few seconds. Therefore, these signals may not last long enough for the integrated garage door opener. The signal is not recognized during programming. Comparable with Canadian law, some U.S. garage door openers are designed to "time-out" in the same manner.
Proceed as follows:
Rif you live in Canada
Rif you have difficulties programming the
garage door opener (regardless of where you live) when using the programming steps
Features
459
X Press and hold one of buttons ; to ? on
the integrated garage door opener. After a short time, indicator lamp : lights up yellow.
X Release the button.
same programming steps with this remote control. Before performing these steps, make sure that new batteries have been installed in garage door drive remote control A.
Indicator lamp : flashes yellow.
RNote that some remote controls only
X Press button B of garage door remote
control A for two seconds, then release it for two seconds.
X Press button B again for two seconds. X Repeat this sequence on button B of
remote control A until indicator lamp : lights up green. If indicator lamp : turns red, repeat the process.
X Continue with the other programming
steps (see above).
Problems when programming
If you are experiencing problems programming the integrated garage door opener on the rear-view mirror, take note of the following instructions:
RCheck the transmitter frequency of garage
door drive remote control A. This can usually be found on the back of the remote control.
The integrated garage door opener is compatible with devices that have units which operate in the frequency range of 280to 433MHz.
RReplace the batteries in garage door remote control A. This increases the likelihood that garage door remote control A will transmit a strong and precise signal to the integrated garage door opener in the rear-view mirror.
transmit for a limited amount of time (the indicator lamp on the remote control goes out). Press button B on remote control A again before transmission ends.
RAlign the antenna cable of the garage door
opener unit. This can improve signal reception/transmission.
Opening/closing the garage door
After it has been programmed, the integrated garage door opener performs the function of the garage door system remote control. Please also read the operating instructions for the garage door system.
X Turn the SmartKey to position 2 in the
ignition lock.
X Press button ;, = or ? which you have programmed to operate the garage door. Garage door system with a fixed code: indicator lamp : lights up green.
Garage door system with a rolling code: indicator lamp : flashes green.
i The transmitter will transmit a signal as
long as the button is pressed. The transmission is halted after a maximum of ten seconds and indicator lamp : lights up yellow. Press button ;, = or ? again if necessary.
Clearing the memory of the integrated
garage door opener on the rear-view
RWhen programming, hold remote control
mirror
A at varying distances and angles from the button that you are programming. Try various angles at a distance between 2and 12 inches (5to 30 cm) or at the same angle but at varying distances.
RIf another remote control for the same
garage door drive is available, repeat the
X Turn the SmartKey to position 2 in the
ignition lock.
X Press buttons ; and ?.
The indicator lamp lights up yellow.
X Press and hold buttons ; and ? until the
indicator lamp turns green.
460 Features
i Make sure that you clear the memory of the integrated garage door opener before selling the vehicle.
Floormat on the driver's side
G WARNING Whenever you are using a floormat, make sure there is enough clearance and that the floormat is securely fastened.
The floormat should always be securely fastened using the fastening equipment.
Before driving off, check that the floormat is securely in place and adjust it if necessary. A loose floormat could slip and hinder proper functioning of the pedals.
Do not place several floormats on top of each other as this may impair pedal movement.
Vehicles without Night View Assist Plus : Areas permeable to radio waves (to the
left and right of the rain sensor cover)
; Rain sensor cover
= Areas permeable to radio waves
Vehicles with Night View Assist Plus : Area permeable to radio waves (to the left
of the rain sensor cover)
; Rain sensor cover
= Areas permeable to radio waves
In order to operate radio-controlled equipment, e.g. toll recording systems, areas : or = on the windshield are permeable to radio waves. In these areas, you can install radio-controlled systems.
These areas can best be seen from outside the vehicle by observing the light reflected off the windshield.
X Slide the seat backwards.
X To install: place the floormat in the
footwell.
X Press studs : onto retainers ;.
X To remove: pull the floormat off
retainers ;.
X Remove the floormat.
Infrared reflective windshield
The infrared reflecting glass prevents the vehicle interior from becoming too hot. It also blocks radio waves up into the gigahertz range.
Useful information ............................ 462
Engine compartment ........................ 462
Maintenance ...................................... 469
Care .................................................... 470
461
462 Engine compartment
Useful information
i This Operator's Manual describes all models and all standard and optional equipment of your vehicle available at the time of publication of the Operator's Manual. Country-specific differences are possible. Please note that your vehicle may not be equipped with all features described. This also applies to safety- related systems and functions.
i Please read the information on qualified
specialist workshops (Y page 31).
Engine compartment
Hood
Opening the hood
G WARNING Do not pull the release lever while the vehicle is in motion. Otherwise, the hood could be forced open by passing air flow.
This could cause the hood to come loose and injure you and/or others.
G WARNING Hybrid vehicles: be sure to read the "HYBRID" supplement. Otherwise, you could fail to recognize dangers.
G WARNING Do not open the hood when the engine is overheated. You could be seriously injured. Observe the coolant temperature gauge to determine whether the engine may be overheated. If you see flames or smoke coming from the engine compartment, move away from the vehicle. Wait until the engine has cooled. If necessary, call the fire department.
Some engine components can become very hot.
To avoid the risk of burns, only touch those components described in the Operator's Manual and observe the relevant safety notes.
G WARNING To avoid injury, stay clear of moving parts when the hood is open and the engine is running.
The radiator fan may continue to run for approximately 30seconds or may even restart after the engine has been switched off. For this reason, you must not reach into the fan rotation area.
G WARNING Vehicles with gasoline engine: The engine is equipped with a transistorized ignition system. Because of the high voltage it is dangerous to touch any components (ignition coils, spark plug sockets, diagnostic socket) of the ignition system
Rwith the engine running
Rwhile starting the engine
Rwhen the ignition is switched on and the
engine is turned manually
G WARNING Vehicles with diesel engine: The engine is equipped with a high-voltage electronic control unit for the injection system. Because of the high voltage it is dangerous to touch any components of the injection system (injectors, electrical wires)
Rwith the engine running
Rwhile starting the engine
Rwhen the ignition is switched on
X Make sure that the windshield wipers are
switched off.
G WARNING There is a risk of injury if the hood is open, even if the engine is not running.
G WARNING The windshield wipers and wiper linkage could be set in motion.
When the hood is open, you or others could be injured by the wiper linkage.
Make sure that the windshield wipers are switched off. Remove the SmartKey or make sure that no ignition position has been selected with KEYLESS-GO. All indicator lamps must be off in the instrument panel.
X Pull release lever : for the hood.
The hood is released.
! Make sure that the windshield wipers are not folded away from the windshield. You could otherwise damage the windshield wipers or the hood.
X Pull hood catch handle ; outwards from the radiator grill as far as it will go and lift the hood from underneath by the radiator grill.
Once you have lifted the hood about 15 inches (40cm), it is automatically opened the rest of the way and held open by the gas-filled struts.
Engine compartment
463
! Do not lift the hood by hood catch
handle ;. The handle may otherwise be damaged.
Closing the hood
G WARNING When closing the hood, use extreme caution not to catch hands or fingers. Be careful that you do not close the hood on anyone.
Make sure the hood is securely engaged before driving off. Do not continue driving if the hood can no longer engage after an accident, for example. The hood could otherwise come loose while the vehicle is in motion and injure you and/or others.
X Lower the hood and let it fall from a height
of approximately 8 inches (20cm).
X Check that the hood has engaged properly. If the hood can be raised slightly, it is not properly engaged. Open it again and close it with a little more force.
Radiator
i Vehicles with a diesel engine: do not
cover the radiator, for example with a winter front or bug cover. The readings of the on-board-diagnostic system may otherwise be inaccurate. Some of these readings are required by law and must be accurate at all times.
Engine oil
Notes on the oil level
G WARNING Hybrid vehicles: be sure to read the "HYBRID" supplement. Otherwise, you could fail to recognize dangers.
Depending on the driving style, the vehicle consumes up to 0.9 US qts (0.8 l) of oil over a distance of 600 miles (1,000 km). The oil
464 Engine compartment
consumption may be higher than this when the vehicle is new or if you frequently drive at high engine speeds.
On vehicles with a 12-cylinder engine, the oil level can be checked using the on-board computer. On all other models, the oil dipstick must be used to check the engine oil level.
Depending on the engine, the oil dipstick may be in a different location.
When checking the oil level:
Rpark the vehicle on a level surface.
Rthe engine should be switched off for
approximately five minutes if the engine is at normal operating temperature.
Rif the engine is not at normal operating temperature, e.g. if the engine was only started briefly: wait about 30 minutes before carrying out the measurement.
Checking the oil level using the oil
dipstick
Example: vehicles with a gasoline engine
Example: vehicles with 4MATIC X Pull oil dipstick : out of the dipstick guide
tube.
X Wipe off oil dipstick :. X Slowly slide oil dipstick : into the guide
tube to the stop, and take it out again. If the level is between MIN mark = and MAX mark ;, the oil level is correct.
X If the oil level has dropped to MIN mark = or below, add 1.1 US qt (1.0 liter) of engine oil.
Checking the oil level using the on-
board computer
Measurement
X Make sure that the SmartKey is in position
2 in the ignition lock.
X Press the; or= button to select the
Service menu.
Engine compartment
465
X Press the : or 9 button to select
Engine Oil Level.
X Press the a button.
The multifunction display shows the following message: Measuring Engine Oil Level Accurate Only When Vehicle Is Level
i If you wish to cancel the measurement,
press the% button on the multifunction steering wheel.
466 Engine compartment
Display messages
The measurement takes a few seconds. You will see one of the following messages in the multifunction display:
Problem
Possible causes/consequences and M Solutions
Engine Oil Level OK The oil level is correct.
Add 1.0 l Engine Oil At Next Refueling.
Add 1.5 l Engine Oil At Next Refueling.
Add 2.0 l Engine Oil At Next Refueling.
Engine Oil Level Reduce Oil Level
For Engine Oil Level Ignition Must be On
Need More Time to Check Engine Oil Level
Engine Oil Level Not When Engine On
The oil level is too low.
X add 1.0 lof engine oil.
The oil level is too low.
X add 1.5 l of engine oil.
The oil level is too low.
X add 2.0 l of engine oil.
The engine oil level is too high.
X Have excess engine oil siphoned off.
The ignition is switched off.
X Turn the SmartKey to position 2 in the ignition lock.
The required waiting period was not observed.
X If the engine is at normal operating temperature: repeat the
measurement after about five minutes.
If the engine is not at normal operating temperature (e.g. if the engine was only started briefly): repeat the measurement after about 30 minutes.
The engine is running; oil level measurement is not possible.
X Switch off the engine.
X If the engine is at normal operating temperature: wait about five
minutes before carrying out the measurement.
If the engine is not at normal operating temperature, e.g. if the engine was only started briefly: wait approximately 30 minutes before carrying out the measurement.
Adding engine oil
G WARNING If engine oil comes into contact with hot engine parts, it may ignite and you could burn
yourself. Do not spill any engine oil on hot engine parts.
H Environmental note When adding oil, take care not to spill any. If oil enters the soil or waterways, it is harmful to the environment.
! Only use engine oils and oil filters that have been approved for vehicles with a service system. You can obtain a list of the engine oils and oil filters tested and approved in accordance with the Mercedes-Benz Specifications for Service Products at any Mercedes-Benz Service center.
Damage to the engine or exhaust system is caused by the following:
Rusing engine oils and oil filters that have
not been specifically approved for the service system
Rreplacing engine oil and oil filters after
the interval for replacement specified by the service system has been exceeded
Rusing engine oil additives.
! Do not add too much oil. adding too much
engine oil can result in damage to the engine or to the catalytic converter. Have excess engine oil siphoned off.
Example: engine oil cap X Turn cap : counter-clockwise and remove
it.
