2007 Mercedes-benz GL Class Owners Manual

On slippery road surfaces, never downshift in order to obtain braking action. This could result in drive wheel slip and reduced vehicle control. Your vehicle’s ABS will not prevent this type of loss of control.

왘 Briefly press left shift button 1.

The transmission will shift to the next lower gear as permitted by the shift program. This action simultaneously limits the gear range of the automatic transmission (컄 page 200).

i To avoid overrevving the engine when down- shifting, the transmission will not shift to a lower gear if the engine’s max. speed would be ex- ceeded.

201

Controls in detail Automatic transmission

Upshifting 왘 Briefly press right shift button 2.

The transmission will shift to the next higher gear as permitted by the shift program. This action simultaneously extends the gear range of the automat- ic transmission (컄 page 200).

Shifting into optimal gear range 왘 Press and hold left shift button 1. The transmission will automatically select the gear range suited for optimal acceleration and deceleration. This will involve shifting down one or more gears.

i If you press on the accelerator when the engine has reached its rpm limit, the transmis- sion will upshift beyond any gear range limit selected.

Canceling gear range limit 왘 Press and hold right shift button 2 until the cipher for the current gear range disappears from the multifunc- tion display (컄 page 200). The transmission will shift from the current gear range directly to gear range D.

202

Emergency operation (Limp-Home Mode)

If vehicle acceleration becomes less re- sponsive or sluggish or the transmission no longer shifts, the transmission is most likely operating in limp-home (emergency operation) mode. In this mode only second gear and reverse gear can be activated. 왘 Stop the vehicle in a safe location. 왘 Shift to park position P. 왘 Turn off the engine. 왘 Wait at least 10 seconds before

restarting.

왘 Restart the engine. 왘 Shift to drive position D (for second

gear) or reverse gear R.

왘 Have the transmission checked at an authorized Mercedes-Benz Light Truck Center as soon as possible.

왔 Transfer case ! Operational or performance test must only be conducted on a two-axle dynanometer. If such tests are necessary, contact an authorized Mercedes-Benz Light Truck Center. You could otherwise seriously damage the brake system or the transfer case which is not covered by the Mercedes-Benz Limited Warranty.

! Because the ESP® operates automatically, the engine and ignition must be shut off (SmartKey in starter switch position 0 or 1 or KEYLESS-GO* start/stop button in position 0 or 1) when testing the parking brake on a brake test dynamometer and such testing should be no longer than 10 seconds. Active braking action through the ESP® may otherwise seriously damage the brake system which is not covered by the Mercedes-Benz Limited Warranty.

i The vehicle is equipped with full-time four-wheel drive. Both the front and rear axles are powered at all times when the vehicle is being operated.

LOW RANGE mode*

The LOW RANGE mode is available on vehi- cles with enhanced off-road package*. In the following situations you should switch to LOW RANGE mode: 앫 during off-road driving (컄 page 357) 앫 when crossing water (컄 page 362) 앫 when towing up or down on steep

gradients

With the LOW RANGE selected, the engine’s power delivery and the shifting behavior of the automatic transmission are adjusted. Furthermore, the ABS, ESP® and 4-ETS functions especially adapted to off-road travel are activated. For information on driving safety systems during LOW RANGE mode, see “Driving safety systems” (컄 page 103). For more information on Off-road driving, see “Off-road driving” (컄 page 357).

Controls in detail Transfer case

Gear Ranges There are two possible settings.

HIGH RANGE

LOW RANGE

Road position for all normal driving situations. (LOW RANGE mode off) Off-road position for traveling on rough terrain. (LOW RANGE mode on) Also use the off-road position when driving on-road on steep gradients, especially when towing a trailer. LOW RANGE acts by raising the engine’s gear ratio. The ve- hicle travels at roughly third the speed compared to when in the HIGH RANGE position, leading to an increase in the engine’s drive power.

203

Controls in detail Transfer case

Warning!

Always wait until the procedure of shifting from HIGH RANGE to LOW RANGE – and from LOW RANGE to HIGH RANGE – has been entirely completed. During this proce- dure do not: 앫 switch off the engine 앫 shift the automatic transmission into

another gear

If you do not wait until the shifting proce- dure has been entirely completed then it might not be correctly performed. The trans- fer case might be in neutral, thus interrupt- ing the transfer of power between the engine and the drive axle.

The vehicle is then freely movable, even if a gear has been selected, and could uninten- tionally be set into motion – particularly on up – or downhill grades. This could lead to an accident and cause injury to yourself and others.

Please observe related messages appearing in the multifunction display (컄 page 493).

204

Switching LOW RANGE mode The switch is located on the upper part of the center console.

Switching LOW RANGE mode on (switching from HIGH RANGE to LOW RANGE)

! The shift procedure can only be performed when the following conditions are met: 앫 The engine is running (컄 page 41). 앫 The automatic transmission is in position N

(컄 page 193).

앫 The vehicle speed does not exceed 25 mph

(40 km/h).

i There is no reset to HIGH after the ignition has been switched off. 왘 Press LOW RANGE switch 1.

Indicator lamp 2 flashes. If the system senses that all conditions are met, it will switch to LOW RANGE mode. A chime sounds and the LOW RANGE display 3 appears in the multi- function display. The indicator lamp 2 on the LOW RANGE switch comes on continu- ously, indicating that the LOW RANGE mode has been activated.

1 LOW RANGE switch 2 Indicator lamp

3 LOW RANGE display

i You can cancel the procedure by pressing the LOW RANGE switch again while the indicator lamp is flashing.

Switching LOW RANGE mode off (switching from LOW RANGE to HIGH RANGE)

! The shift procedure can only be performed when the following conditions are met: 앫 The engine is running (컄 page 41). 앫 The automatic transmission is in position N

(컄 page 193).

앫 The vehicle speed does not exceed 43 mph

(70 km/h).

i There is no reset to LOW after the ignition has been switched off.

왘 Press LOW RANGE switch 1

(컄 page 204). Indicator lamp 2 flashes. If the system senses that all conditions are met, it will switch to back to HIGH RANGE mode. A chime sounds and the LOW RANGE display 3 ap- pears in the multifunction display. The indicator lamp 2 on the LOW RANGE switch goes out, indicat- ing that the LOW RANGE mode has been deactivated.

i You can cancel the procedure by pressing the LOW RANGE switch again while the indicator lamp is flashing.

For messages in the multifunction display, see “Practical hints” section (컄 page 493).

Controls in detail Transfer case

205

Controls in detail Differential locks*

For more information on Off-road driving, see “Off-road driving” (컄 page 357). Vehicles with enhanced off-road package* are equipped with automatic locks for the center and rear axle differential to improve vehicle traction. 앫 The center differential compensates for differences in wheel rotation be- tween the front and rear axle.

앫 The rear axle differential compensates

differences between the rear wheels.

i At the front axles, the 4-ETS system (컄 page 109) compensates for any traction problems.

206

A few words about differentials and differential locks*

When a vehicle negotiates a turn, wheels on the outside of the curve must travel far- ther and rotate faster than the inside wheels. The differential, the operation of a set of gears that allows the powered wheels in a vehicle to turn at different speeds, makes this essential function pos- sible. The drawback is that the differential also sends most of the engine’s power to the wheel with the least load or strain on it. For example, if one of a vehicle’s powered wheels sits on a patch of snow and spins because there is no traction, all of the en- gine’s power will go to that wheel because the power will take the path of least resis- tance. Meanwhile, the opposite wheel, sit- ting on dry pavement where it could get enough grip to start the vehicle moving, sits idle because it receives no power.

The Electronic Traction System (ETS) ad- dresses this problem and provides for good control and steering ability by auto- matically slowing the slipping wheel and thus increasing the power to the other non-slipping drive wheels to get the vehicle moving. The ESP® and ETS in this vehicle feature such intelligent limited-slip differ- ential technology, ideally suited for on-road and light off-road driving. Transfer case position LOW (컄 page 203) also en- hances off-road driving capabilities (컄 page 357). More extreme off-road conditions may call for another solution, engaging a differen- tial lock or preventing the differential from operating altogether. This vehicle comes with two differential locks: transfer case (center) and rear. Each can be engaged simply by operating a rotary switch located on the center console (컄 page 207). When the transfer case (center) differential is locked, the combined (or average) speed of the front wheels is identical to the com- bined rear wheel speed. When the rear differential is locked, both rear wheels turn

Switching differential locks*

! If the differential locks are engaged, accel- erate gently when setting the vehicle in motion. To avoid damage to the transmission, the vehicle may only be operated on a dynamometer (single axle dynamometer) if 앫 the axle not being driven is jacked up or 앫 the associated propeller shaft is disconnect-

ed.

at the same speed, independent of the in- dividual torque. Please be aware that en- gaging the differential locks will significantly reduce the steering ability of the vehicle. For your safety and the safety of others and to prevent damage to the vehicle, the differential locks must not be engaged when driving on paved roads. It is impor- tant to understand that during on-road/paved driving, differentials are absolutely necessary for providing the es- sential control and steering ability of the vehicle. The differential locks, therefore, must not be engaged when driving on paved roads and should only be used to the extent necessary to negotiate off-road conditions which cannot be handled by the systems (automatic 4-ETS, the ESP®, man- ual switch position “LOW” of transfer case) this vehicle comes equipped with.

Controls in detail Differential locks*

The rotary switch for the differential locks is located on the upper part of the center console. You can select between three locking modes.

1 Rotatable outer adjustment ring with

indicator lamp

2 AUTO mode: center differential is auto-

matically locked

3 Center differential is completely locked 4 Center and rear axle differential are

completely locked

207

Controls in detail Differential locks*

AUTO mode The AUTO mode is adequate for most driv- ing situations since the center differential is locked and released as required.

i At speeds up to 19 mph (30 km/h), it is possible to manually lock the differential locks for driving on rough terrain. 왘 Start the engine (컄 page 42).

The center differential locks is in AUTO mode. The indicator lamp on the adjustment ring 1 above symbol U 2 is on.

208

The differential locks should only be engaged manually if traction is insufficient in AUTO mode. The differential locks can be engaged in the sequence 3, 4 (컄 page 207) up to a speed of 19 mph (30 km/h). Engaging differential locks: 앫 for off-road driving 앫 for driving through water 앫 when driving on deep snow and icy or

fouled surfaces

Center and rear axle differential locks

Warning!

Never drive on a paved surface with the center and rear axle differential locks manually engaged. Ability to steer the vehicle is greatly reduced when the differen- tial locks are manually engaged, increasing the risk of an accident.

For safety reasons, the locks are automati- cally released at a vehicle speed above 31 mph (50 km/h). Nevertheless, you should only manually lock the differential if absolutely necessary because engaged locks will restrict the vehicle drive train while cornering and cause the vehicle to chatter. This could cause you to lose control of the vehicle and cause an accident.

! The differential locks must not be engaged manually when towing the vehicle or spinning the wheels.

왘 Start the engine (컄 page 42). 왘 To select the required locking mode,

rotate adjustment ring 2 to the desired position 3 or 4 (컄 page 207). The indicator lamp on the adjustment ring 1 at the respective symbol comes on.

! If the differential locks have been manually engaged, the tires will scuff on the road surface when cornering because the differences be- tween the individual wheel rotation speeds will not be compensated for.

i The differential locks are reset to AUTO mode after the ignition has been switched off for longer than 10 seconds.

Example 5 Center differential is completely locked

Controls in detail Differential locks*

209

Controls in detail Good visibility

For information on windshield wipers, see “Windshield wipers” (컄 page 63).

Headlamp cleaning system*

The headlamp cleaning button is located on the left side of the dashboard.

1 Headlamp cleaning button

210

왘 Switch on the ignition (컄 page 42). 왘 Press button 1.

The headlamps are cleaned with a high-pressure water jet.

i The headlamps will automatically be cleaned when you have 앫 switched on the headlamps

and

앫 operated the windshield wipers with wind-

shield washer fluid fifteen times

When you switch off the ignition, the counter resets.

For information on filling up the washer reservoir, see “Windshield/rear window washer system and headlamp cleaning system*” (컄 page 384).

Rear view mirrors

For more information on setting the rear view mirrors, see “Mirrors” (컄 page 52).

Interior rear view mirror, antiglare position

1 Lever 왘 Tilt the mirror to the antiglare position by moving lever 1 towards the wind- shield. The interior rear view mirror is dimmed.

Auto-dimming rear view mirrors* The reflection brightness of the exterior rear view mirror on the driver’s side and the interior rear view mirror will respond automatically to glare when 앫 the ignition is switched on

and

앫 incoming light from headlamps falls on

the sensor in the interior rear view mirror

The rear view mirror will not react if 앫 the automatic transmission is set to

position R

앫 the interior lighting is turned on

Controls in detail Good visibility

Warning!

Power folding exterior rear view mirrors*

! Before you drive the vehicle through an automatic car wash, fold the exterior rear view mirrors in. Otherwise they may get damaged.

Folding the exterior rear view mirrors in and out automatically When the corresponding function in the control system is activated (컄 page 185): 앫 The exterior rear view mirrors automat- ically fold in as soon as the vehicle is locked from the outside.

앫 The exterior rear view mirrors automat- ically fold out as soon as the vehicle is unlocked and the driver’s or front pas- senger door are subsequently opened.

The auto-dimming function does not react if incoming light is not aimed directly at sen- sors in the interior rear view mirror.

The interior rear view mirror and the exterior rear view mirror on the driver’s side do not react, for example, when transporting cargo which covers the rear window.

Light hitting the mirror(s) at certain angles (incident light) could blind you. As a result, you may not be able to observe traffic con- ditions and could cause an accident.

Warning!

Exercise care when using the passen- ger-side exterior rear view mirror. The mirror surface is convex (outwardly curved surface for a wider field of view). Objects in mirror are closer than they appear. Check your interior rear view mirror or glance over your shoulder before changing lanes.

211

Controls in detail Good visibility

Synchronizing exterior rear view mirrors The power folding rear view mirrors may have to be synchronized after the vehicle battery has been disconnected or dis- charged. If the exterior rear view mirrors do not fold properly upon locking or un- locking the vehicle although the corre- sponding function in the control system is activated (컄 page 185), do the following: 왘 Fold each exterior rear view mirror in

completely (컄 page 212).

왘 Fold each exterior rear view mirror out

completely (컄 page 212).

When the exterior rear view mirrors fold properly upon locking the vehicle, the exte- rior mirrors are synchronized. Otherwise repeat the above steps.

212

Folding the exterior rear view mirrors in and out manually

Folding in 왘 Briefly press button 1.

i The exterior rear view mirrors can vibrate if they are not folded out completely.

The button is located on the door control panel.

Both exterior rear view mirrors fold in.

i If you are driving at more than approximately 30 mph (47 km/h), you will not be able to fold the exterior mirrors in.

Folding out 왘 Briefly press button 1 again.

Both exterior rear view mirrors fold out.

! If an exterior rear view mirror housing is forcibly pushed forward (hit from the rear) or forcibly pushed rearward (hit from the front) press button 1 to fold mirrors in, then press button 1 again to fold mirrors out. Do not force mirrors by hand as this may damage the adjust- ment mechanism. The mirror housing is then properly positioned and you can adjust the mirror in the usual manner. Please make sure both rear view mirrors are folded out before driving off.

1 Button for folding exterior rear view

mirrors in and out

왘 Switch on the ignition (컄 page 42).

Sun visors

The sun visors protect you from sun glare while driving.

Warning!

Do not use the vanity mirror while driving.

Keep the mirrors in the sun visors closed while vehicle is in motion. Reflected glare can endanger you and others.

1 Sun visor 2 Additional sun visor* 3 Mirror lamp 4 Vanity mirror cover 5 Vanity mirror 6 Holder for gas cards 7 Mounting

Controls in detail Good visibility

Glare through the windshield 왘 Swing sun visor 1 down. 왘 Make sure sun visor 1 is properly en-

gaged in mounting 7.

왘 When you do not experience glare any-

more, swing sun visor 1 up.

Vanity mirror 왘 Swing sun visor 1 down. 왘 Flip up cover 4 to access vanity

mirror 5. Vanity mirror lamp 3 comes on.

왘 After using vanity mirror 5, flip down

cover 4.

왘 Swing sun visor 1 up.

213

Controls in detail Good visibility

Glare through a side window

1 Sun visor 2 Additional sun visor* 왘 Swing sun visor 1 down. 왘 Disengage sun visor 1 from

mounting 7 (컄 page 213).

왘 Pivot sun visor 1 to the side.

214

! To avoid damage to vanity mirror cover 4 (컄 page 213), make sure it is closed before pivoting sun visor 1 to the side. 왘 Adjust sun visor 1 by pushing or pull-

ing in the direction of arrows.

왘 Swing down additional sun visor* 2 when you experience additional glare through the windshield.

Rear panorama roof sunshade

The rear panorama roof sunshade over the third-row seats prevents the sun from shin- ing directly into the vehicle. You can open and close the sunshade by hand.

! Always guide the sunshade. Do not let it snap back abruptly, as it could be damaged.

1 Mounting 2 Clip 3 Handle 4 Button

Closing 왘 Grasp on handle 3 and insert clips 2

into mounting 1. The third-row sunshade engages.

Opening 왘 Press on button 4 to disengage the third-row sunshade from mounting 1.

Rear window defroster

The rear window defroster uses a large amount of power. To keep battery drain to a minimum, switch off the defroster as soon as the rear window is clear. The de- froster is automatically deactivated after approximately 6 to 17 minutes of operation depending on the outside tem- perature.

Activating 왘 Press button 1 on the climate con- trol panel (컄 page 218) or the automat- ic climate control* panel (컄 page 232). The indicator lamp on the button comes on.

Deactivating 왘 Press button 1 once more.

Warning!

The indicator lamp on the button goes out.

Any accumulation of snow and ice should be removed from the rear window before driv- ing. Visibility could otherwise be impaired, endangering you and others.

왘 Switch on the ignition (컄 page 42).

! If the rear window defroster switches off too soon and the indicator lamp starts flashing, too many electrical consumers are operating simul- taneously and there is insufficient voltage in the battery. The system responds automatically by switching the rear window defroster off. As soon as the battery has sufficient voltage, the rear window defroster switches back on auto- matically.

Controls in detail Good visibility

215

Controls in detail Climate control

216

Controls in detail Climate control

i For draft-free ventilation, move the sliders for center air vents and side air vents to the middle position.

1 Driver’s door air vent, fixed 2 Left side air vent, adjustable 3 Thumbwheel for air volume control

for left side and door air vent

4 Thumbwheel for air volume control

for left center air vent

5 Left center air vent, adjustable 6 Right center air vent, adjustable 7 Thumbwheel for air volume control

for right center air vent

8 Thumbwheel for air volume control

for right side and door air vent 9 Right side air vent, adjustable a Front passenger door air vent, fixed b Climate control panel

217

Controls in detail Climate control

218

1 Temperature control, left 2 Air distribution and air volume

(automatic, manual)

3 Front defroster

or, depending on vehicle production date,

4 Increasing air volume 5 Air distribution (directs air through

the windshield and side air vents)

6 Rear climate control* on/off Air supply for rear passenger compartment on/off : USA only < Canada only

7 Temperature control, right 8 AC cooling on/off

Residual heat/ventilation

9 Air distribution (directs air through

center and side air vents)

a Air distribution (directs air through

the footwells and side air vents)

b Air volume display c Decreasing air volume d Rear window defroster e Air recirculation f Interior temperature sensor g Climate control on/off

The climate control is operational whenev- er the engine is running. You can operate the climate control system in either the automatic or manual mode. The system cools or heats the interior depending on the selected interior temperature and the current outside temperature.

Nearly all dust particles, pollutants and odors are filtered out before outside air en- ters the passenger compartment through the air distribution system. The air conditioning will not engage (no cooling) if the A/C mode is deactivated (컄 page 226).

Warning!

Warning!

Follow the recommended settings for heat- ing and cooling given on the following pag- es. Otherwise the windows could fog up, impairing visibility and endangering you and others.

When operating the climate control, the air that enters the passenger compartment through the air vents can be very hot or very cold (depending on the set temperature). This may cause burns or frostbite to unpro- tected skin in the immediate area of the air vents.

Always keep sufficient distance between un- protected parts of the body and the air vents. If necessary, use the air distribution controls (컄 page 218) to direct the air to air vents in the vehicle interior that are not in the immediate area of unprotected skin.

Controls in detail Climate control

i Severe conditions (e.g. strong air pollution) may require replacement of the filter before its scheduled interval. A clogged filter will reduce the air volume to the interior. If the vehicle interior is hot, ventilate the interior before driving off, see “Summer opening fea- ture” (컄 page 251). The climate control will then adjust the interior temperature to the set value much faster. Keep the air intake grille in front of the wind- shield free of snow and debris.

219

Controls in detail Climate control

Deactivating the climate control system

Warning!

When the climate control system is switched off, the outside air supply and cir- culation are also switched off. Only choose this settings for a short time. Otherwise the windows could fog up, impairing visibility and endangering you and others.

Deactivating 왘 Press button ´ (컄 page 218). The indicator lamp on the button comes on.

Reactivating 왘 Press button U (컄 page 218).

i You can also press button ´ (컄 page 218) on the climate control panel. If you press button 0 or, depending on vehi- cle production date, button |(컄 page 218) to reactivate the climate control system, the defrosting mode is activated.

Operating the climate control system in automatic mode

i When operating the climate control system in automatic mode, you will only rarely need to adjust the temperature, air volume and air distri- bution. In automatic mode, cooling with dehumidify is switched on. This function can be switched off if necessary (컄 page 227).

220

Activating 왘 Press button U (컄 page 218) while

the engine is running. The indicator lamp on the button comes on. The air volume and air distri- bution are adjusted automatically.

왘 Use temperature controls 1 and 7 (컄 page 218) to separately adjust the air temperature on each side of the passenger compartment. The interior air temperature is adjusted automatically.

i The settings for the passenger side are also used for the rear passenger compartment.

Deactivating 왘 Press button ˜ or Q

(컄 page 218). The indicator lamp on button U goes out. The automatic operation of air volume switches off. The selected blower speed is shown in the air volume display b (컄 page 218).

or 왘 Press air distribution button 5, 9,

or a (컄 page 218). The indicator lamp on button U goes out. The automatic operation of air distribution switches off.

Setting the temperature

Use temperature controls 1 and 7 (컄 page 218) to separately adjust the air temperature on each side of the passenger compartment. You should raise or lower the temperature setting in small incre- ments, preferably starting at 72°F (22°C). The climate control will adjust to the set temperature as fast as possible.

Increasing 왘 Turn temperature control 1

and/or 7 (컄 page 218) slightly clock- wise. The climate control system will corre- spondingly adjust the interior air tem- perature.

Decreasing 왘 Turn temperature control 1

and/or 7 (컄 page 218) slightly coun- terclockwise. The climate control system will corre- spondingly adjust the interior air tem- perature.

Controls in detail Climate control

Adjusting air distribution

Press air distribution button 5, 9, or a (컄 page 218) to adjust the air distribution. The following symbols are found on the controls:

Symbol Function a Directs air through the center

and side air vents

Z Directs air to the windshield

and side air vents

Y Directs air to the footwells and

side air vents

왘 Press the desired air distribution

button 5, 9, or a (컄 page 218). The indicator lamp on button U goes out.

221

Controls in detail Climate control

Adjusting air volume

Five blower speeds are available. 왘 Press button ˜ to decrease or button Q to increase air volume (컄 page 218) to the desired level. The indicator lamp on button U (컄 page 218) goes out. The automatic operation of air volume switches off. The selected blower speed is shown in the air volume display b (컄 page 218).

Adjusting air volume for the center and side air vents

Opening the center air vents 왘 Turn thumbwheels 4 and 7

(컄 page 216) to the right. The corresponding center air vents on the left and right are open.

222

Closing the center air vents 왘 Turn thumbwheels 4 and 7

(컄 page 216) to the left. The corresponding center air vents on the left and right are closed.

Opening the side air vents 왘 Turn thumbwheels 3 and 8

(컄 page 216) to the right. The corresponding side air vents on the left and right are open.

Closing the side air vents 왘 Turn thumbwheels 3 and 8

(컄 page 216) to the left. The corresponding side air vents on the left and right are closed.

Air vents in the roof liner over the second-row seats*

1 Thumbwheel for air volume control 2 Air vent, adjustable

Adjusting air volume 왘 Turn thumbwheel 1 down to decrease

the air volume.

or 왘 Turn thumbwheel 1 up to increase the

air volume.

Adjusting air distribution 왘 Move air vent slider 2 to the left, right, up, or down to direct the air in the de- sired direction.

Front defroster

You can use this setting to defrost the windshield, for example if it is iced up. You can also use it to defog the windshield and door windows.

i Keep this setting selected only until the windshield or the door windows are clear again.

Activating 왘 Press button 0 or, depending on vehicle production date, button | (컄 page 218). The indicator lamp on the button comes on.

The climate control switches to the follow- ing functions automatically: 앫 most efficient blower speed and

heating power, depending on outside temperature

앫 air flows onto the windshield and the door windows (side air vents must be open)

앫 the air conditioning compressor

switches on at outside temperatures above approximately 41°F (5°C) for air-drying

Adjustments You can adjust the air volume and the tem- perature when the front defroster is switched on. The air flow will remain on the windshield and door windows. 왘 Press button ˜ to decrease or button Q to increase air volume (컄 page 218) to the desired level.

Controls in detail Climate control

The air volume decreases/increases to the next lower/higher blower speed and heating switches to the tempera- ture that was set before the front de- froster was switched on. The indicator lamp on button 0 or, depending on vehicle production date, button | goes out. The indicator lamp on button 9 comes on.

or 왘 Turn temperature control 1

and/or 7 (컄 page 218) slightly in any direction. Heating switches to the temperature that was set before the front defroster was switched on. The indicator lamp on button 0 or, depending on vehicle production date, button | goes out. The indicator lamp on button 9 comes on.

컄컄

223

Controls in detail Climate control

컄컄

i The air conditioning compressor remains on even if the indicator lamp in button 0 or, de- pending on vehicle production date, button | goes out. This helps to prevent the windshield from fogging.

Deactivating 왘 Press button 0 or, depending on vehicle production date, button | (컄 page 218) once more. The indicator lamp on the button goes out. Defrosting is turned off. The previous settings are in effect again. The air conditioning compressor remains switched on.

i To switch off, you can also press button ´ or U (컄 page 218).

224

Windshield fogged on the outside

i Keep this setting selected only until the windshield is clear again. 왘 Switch the windshield wipers on

(컄 page 64).

왘 Press button 0 or, depending on

vehicle production date, button | (컄 page 218). The indicator lamp on the button comes on.

The climate control switches automatically to the following functions: 앫 most efficient blower speed and

heating power, depending on outside temperature

앫 air flows onto the windshield and the door windows (side air vents must be open)

앫 the air conditioning compressor

switches on at outside temperatures above approximately 41°F (5°C) for air-drying

If the automatic air distribution is switched off: 왘 Press air distribution button 9 or a

(컄 page 218).

Air recirculation mode

Switch to air recirculation mode to prevent unpleasant odors from entering the vehicle from the outside (e.g. before driving through a tunnel). This setting cuts off the intake of outside air and recirculates the air in the passenger compartment.

Warning!

Fogged windows impair visibility, endangering you and others. If the windows begin to fog on the inside, switching off the air recirculation mode immediately should clear interior window fogging. If interior win- dow fogging persists, make sure the air conditioning (컄 page 218) is activated, or press button 0 or, depending on vehicle production date, button |.

Activating 왘 Press button : (컄 page 218). The indicator lamp on the button comes on.

i The air recirculation mode is activated auto- matically at high outside temperatures. The indicator lamp on button : is not lit when the air recirculation mode is switched on auto- matically. A quantity outside air is added after approximately 30 minutes. If you have turned off the air conditioning (컄 page 226) or the outside temperature is below 41°F (5°C), the air recirculation mode will not switch on automatically.

i To cool the interior as fast as possible, the climate control automatically switches to air recirculation. The indicator lamp on button : is not lit when the air recirculation mode has been switched on automatically.

Controls in detail Climate control

Deactivating 왘 Press button :.

Air recirculation mode with conve- nience closing and opening feature

The indicator lamp on the button goes out.

Warning!

i The air recirculation mode is deactivated automatically 앫 after 5 minutes if the outside temperature is

below approximately 41°F (5°C)

앫 after 5 minutes if the air conditioning and

air-drying is turned off

앫 after 30 minutes if the outside temperature

is above approximately 41°F (5°C)

Never operate the windows and tilt/sliding sunroof* if there is the possibility of anyone being harmed by the opening or closing pro- cedure.

When using the air recirculation mode with convenience closing feature, should the up- ward movement of a window be blocked by some obstruction including but not limited to arms, hands, fingers, etc., the automatic reversal feature will not operate.

In case the procedure causes potential danger:

Vehicles with or without tilt/sliding sun- roof*: The closing of the windows can be im- mediately halted by pressing or pulling the respective window switch. The closing of the tilt/sliding sunroof* can be immediately halted by moving the switch for the tilt/slid- ing sunroof* in any direction.

컄컄

225

Controls in detail Climate control

컄컄

The closing of the windows and the tilt/sliding sunroof* can be reversed by again pressing and holding the : button.

Convenience closing 왘 Press button : for approximately

2 seconds. The windows and/or tilt/sliding sun- roof* will close. You can release button : once the closing proce- dure has begun. The windows and tilt/sliding sunroof* continue closing until they are fully closed. The indicator lamp on the button comes on. The air recirculation mode is activated.

226

Convenience opening 왘 Press button : for approximately

2 seconds. The windows and/or tilt/sliding sun- roof* will return to their previous posi- tions. You can release button : once the opening procedure has be- gun. The windows and tilt/sliding sun- roof* continue opening until they have reached their previous positions. The indicator lamp on the button goes out. The air recirculation mode is deactivat- ed.

i A window or the tilt/sliding sunroof* will only return to its previous position if it has not been moved to another position using the re- spective window switch or tilt/sliding sunroof* switch after it was closed with button :.

Air conditioning

The air conditioning is operational while the engine is running and cools the interior air to the temperature set by the operator. In addition, the air conditioning dehumidi- fies the interior air at outside temperatures above 41°F (5° C) and helps prevent window fogging.

i Condensation may drip out from underneath the vehicle. This is normal and not an indication of a malfunction.

Warning!

If you turn off the cooling function, the interior air is not dried. The windows can fog up more quickly. Window fogging may impair visibility and endanger you and others.

Controls in detail Climate control

Deactivating It is possible to deactivate the air condi- tioning (cooling) function of the climate control system. The air in the vehicle will then no longer be cooled or dehumidified. 왘 Press button 9 (컄 page 218).

The indicator lamp on the button goes out.

Activating Moist air can fog up the windows. You can dehumidify the air with the air condition- ing. 왘 Press button 9 (컄 page 218) again.

The indicator lamp on the button comes on.

The air conditioning uses the refrigerant R134a. This refrigerant is free of CFCs which are harmful to the ozone layer.

! If the air conditioning cannot be turned on again, this indicates that the air conditioning is losing refrigerant. The compressor has turned off. Have the air conditioning checked at the nearest authorized Mercedes-Benz Light Truck Center.

Activating 왘 Switch off the ignition (컄 page 42). 왘 Press button 9 (컄 page 218). The indicator lamp on the button comes on.

Residual heat and ventilation

With the engine switched off, it is possible to continue to heat or ventilate the interior for up to 30 minutes. This feature makes use of the residual heat produced by the engine.

i How long the system will provide heating depends on 앫 the coolant temperature 앫 the battery voltage Regardless of the temperature and air volume set on the climate control panel, the interior tem- perature is set to 72°F (22°C) and the blower runs on low speed to protect the vehicle battery.

Deactivating 왘 Press button 9 (컄 page 218).

The indicator lamp on the button goes out.

i The residual heat is automatically turned off: 앫 when the ignition is switched on 앫 after about 30 minutes 앫 if the coolant temperature is too low 앫 if the battery voltage drops

227

Controls in detail Climate control

Rear climate control*

i The rear climate control panel is only available if your vehicle is equipped with seat heating* for the rear seats or Rear Audio fea- ture* (see separate COMAND System operating instructions).

The control panel is located on the rear of the front center console.

228

Deactivating rear climate control 왘 Press button ´.

The indicator lamp on the button comes on. The cooling function switches off after a short delay.

i Switch off the rear climate control for im- proved cooling or heating output in the front pas- senger compartment. You can also switch off the rear climate control from the front passenger compartment (컄 page 229).

1 Left rear center air vent, adjustable 2 Right rear center air vent, adjustable 3 Rear climate control on

(automatic mode)

4 Air distribution (directs air through

the center air vents)

5 Air distribution (directs air through

the footwells and side air vents)

6 Rear air conditioning off

Activating rear climate control

i The climate control must be switched on (컄 page 229). 왘 Press button U.

The indicator lamp on the button comes on. The air volume and air distri- bution are adjusted automatically.

i The temperature is adjusted according to the settings for the front passenger side made on the front climate control panel (컄 page 221).

Operating from the front

Deactivating 왘 Press button : on the front climate

control panel (컄 page 218). The indicator lamp on the button comes on.

Reactivating 왘 Press button : on the front climate

control panel (컄 page 218). The indicator lamp on the button goes out. The rear climate control is adjust- ed automatically.

Adjusting air distribution Use the air distribution controls 4 or 5 to adjust the air distribution for the rear passenger compartment. The following symbols are found on the controls:

Symbol Function Z Directs air to the center air

vents

Y Directs air to the footwells and

the side air vents

Adjusting manually 왘 Press the desired air distribution

control 4 or 5. The indicator lamp in the U button goes out.

Controls in detail Climate control

Adjusting automatically 왘 Press button U (컄 page 228). The indicator lamp on the button comes on. The air distribution is adjust- ed automatically.

Adjusting air volume The air volume for the rear zone corre- sponds to the air volume settings for the front passenger side. You can switch off the air supply for the rear zone. You can switch off the supplied amount of air volume. 왘 Press button ´ (컄 page 228). The indicator lamp on the button comes on.

229

Controls in detail 3-zone automatic climate control*

230

Controls in detail 3-zone automatic climate control*

i For draft-free ventilation, move the sliders for center air vents and side air vents to the middle position.

1 Driver’s door air vent, fixed 2 Left side air vent, adjustable 3 Thumbwheel for air volume control

for left side and door air vent

4 Thumbwheel for air volume control

for left center air vent

5 Left center air vent, adjustable 6 Right center air vent, adjustable 7 Thumbwheel for air volume control

for right center air vent

8 Thumbwheel for air volume control

for right side and door air vent 9 Right side air vent, adjustable a Front passenger door air vent, fixed b Automatic climate control panel

231

Controls in detail 3-zone automatic climate control*

232

1 Temperature control, left 2 Air distribution and air volume

(automatic, manual)

3 Air distribution, driver’s side 4 Front defroster

or, depending on vehicle production date,

5 Increasing air volume 6 Rear window defroster 7 Air distribution, passenger side 8 Rear automatic climate control

on/off > USA only ™ Canada only

9 Temperature control, right a Automatic climate control on/off b Air distribution, passenger side c Air distribution, passenger side d AC cooling on/off

Residual heat/ventilation

e Display f Decreasing air volume g Air recirculation h Air distribution, driver’s side j Air distribution, driver’s side k Interior temperature sensor l Adopting driver’s side settings for all

zones

The automatic climate control is a 3-zone intelligent automatic climate control sys- tem. Your vehicle interior is divided into 3 zones.

Warning!

When operating the automatic climate con- trol, the air that enters the passenger com- partment through the air vents can be very hot or very cold (depending on the set tem- perature). This may cause burns or frostbite to unprotected skin in the immediate area of the air vents.

Always keep sufficient distance between un- protected parts of the body and the air vents. If necessary, use the air distribution controls (컄 page 232) to direct the air to air vents in the vehicle interior that are not in the immediate area of unprotected skin.

Controls in detail 3-zone automatic climate control*

With the help of a sun sensor, the automat- ic climate control determines the relation of the sun to the vehicle and automatically adjusts the inside temperature for every individual zone. The automatic climate control is operation- al whenever the engine is running. It cools the vehicle’s interior according to the an- gle and intensity of the sun’s rays, the out- side temperature and the selected temperature. You can operate the auto- matic climate control in either the auto- matic or manual mode. Nearly all dust particles, pollutants and odors are filtered out before outside air en- ters the passenger compartment through the air distribution system. The air conditioning will not engage (no cooling) if the A/C mode is deactivated (컄 page 232).

233

Controls in detail 3-zone automatic climate control*

Warning!

Deactivating the automatic climate control system

Reactivating 왘 Press button U(컄 page 232).

Follow the recommended settings for heat- ing and cooling given on the following pag- es. Otherwise the windows could fog up, impairing visibility and endangering you and others.

i Severe conditions (e.g. strong air pollution) may require replacement of the filter before its scheduled interval. A clogged filter will reduce the air volume to the interior. If the vehicle interior is hot, ventilate the interior before driving off, see “Summer opening fea- ture” (컄 page 251). The automatic climate con- trol will then adjust the interior temperature to the set value much faster. Keep the air intake grille in front of the wind- shield free of snow and debris.

Warning!

When the automatic climate control system is switched off, the outside air supply and circulation are also switched off. Only choose this settings for a short time. Other- wise the windows could fog up, impairing visibility and endangering you and others.

Deactivating 왘 Press button ´ (컄 page 232) until the display e (컄 page 232) is cleared. The indicator lamp on the button comes on.

i You can also press button ´ (컄 page 232) on the automatic climate control panel. If you press button 0 or, depending on vehicle production date, button | (컄 page 232) to reactivate the automatic climate control system, the defrosting mode is activated.

234

Operating the automatic climate control system in automatic mode

You can switch the automatic climate con- trol system on and off separately for each zone as needed.

i When operating the automatic climate control system in automatic mode, you will only rarely need to adjust the temperature, air volume and air distribution. In automatic mode, cooling with dehumidify is switched on. This function can be switched off if necessary.

Activating 왘 Press button U (컄 page 232) while

the engine is running. The indicator lamp on the button comes on. Air volume and air distribu- tion are controlled separately for each zone.

왘 Use temperature controls 1 and 9 (컄 page 232) to separately adjust the air temperature on each side of the passenger compartment. The temperature of the interior is ad- justed automatically.

Deactivating 왘 Press one button of the air distribution

(컄 page 232) or press button ˜ or Q (컄 page 232). The indicator lamp on button U goes out. Depending on which button you press – the air distribution button or the air vol- ume button ˜ or Q – automatic control of either the air distribution or air volume is switched off.

Controls in detail 3-zone automatic climate control*

Setting the temperature

Use temperature control 1 and 9 (컄 page 232) to separately adjust the air temperature on each side of the passenger compartment. You should raise or lower the temperature setting in small incre- ments, preferably starting at 72°F (22°C). The automatic climate control will adjust to the set temperature as fast as possible.

Increasing 왘 Turn temperature control 1 and/or 9 slightly clockwise. The automatic climate control system will correspondingly adjust the interior air temperature.

Decreasing 왘 Turn the temperature control 1

and/or 9 slightly counterclockwise. The automatic climate control system will correspondingly adjust the interior air temperature.

235

Controls in detail 3-zone automatic climate control*

Adjusting air distribution

Use the air distribution controls 3, h, or j for the driver’s side, or 7, b, or c (컄 page 232) for the passenger side to separately adjust the air distribution on each side of the passenger compartment. The following symbols are found on the buttons:

Symbol

Function

Passen- ger side

Driver’s side 6 Z Directs air to the

windshield and side air vents

7 a Directs air through the center, side and rear passenger compartment air vents

8 Y Directs air to the footwells and side air vents

236

Opening the side air vents 왘 Turn thumbwheels 3 and 8

(컄 page 230) to the right. The corresponding side air vents on the left and right are open.

Closing the side air vents 왘 Turn thumbwheels 3 and 8

(컄 page 230) to the left. The corresponding side air vents on the left and right are closed.

왘 Press the desired air distribution but-

ton (컄 page 232). The indicator lamp on the desired but- ton goes out.

Adjusting the air distribution for the center and side air vents

Opening the center air vents 왘 Turn thumbwheels 4 and 7

(컄 page 230) to the right. The corresponding center air vents on the left and right are open.

Closing the center air vents 왘 Turn thumbwheels 4 and 7

(컄 page 230) to the left. The corresponding center air vents on the left and right are closed.

Adjusting air volume

Front defroster

Five blower speeds are available. 왘 Press button ˜ to decrease or button Q to increase air volume (컄 page 232) to the desired level. The indicator lamp on button U goes out. The automatic mode is switched off. The selected blower speed appears in the display e (컄 page 232).

You can use this setting to defrost the windshield, such as when it is iced up. You can also use it to defog the windshield and door windows.

i Keep this setting selected only until the windshield or the side windows are clear again.

Activating 왘 Press button 0 or, depending on

vehicle production date, button | (컄 page 232). The indicator lamp on the button comes on.

Controls in detail 3-zone automatic climate control*

The automatic climate control switches to the following functions automatically: 앫 most efficient blower speed and

heating power, depending on outside temperature

앫 air flows onto the windshield and the door windows (side air vents must be open)

앫 the air conditioning compressor

switches on at outside temperatures above approximately 41°F (5°C) for air-drying

Adjustments You can adjust the air volume and the tem- perature when the front defroster is switched on. The air flow will remain on the windshield and door windows.

237

i The air conditioning compressor remains on even if the indicator lamp in button 0 or, de- pending on vehicle production date, button | goes out. This helps to prevent the windshield from fogging.

Deactivating 왘 Press button 0 or, depending on

vehicle production date, button | (컄 page 232). The indicator lamp on the button goes out. Defrosting is turned off. The previous settings are once again in effect.

i To switch off, you can also press button ´ or U (컄 page 232).

Windshield fogged on the outside

i Keep this setting selected only until the windshield is clear again. 왘 Switch the windshield wipers on

(컄 page 64).

왘 Press button U (컄 page 232).

The indicator lamp on button U goes out. Air volume and air distribution are controlled separately for each zone.

If the automatic air distribution and air volume are switched off: 왘 Press buttons 8 and Y

(컄 page 232).

Controls in detail 3-zone automatic climate control*

왘 Press button ˜ to decrease or button Q to increase air volume (컄 page 232) to the desired level. The air volume decreases/increases to the next lower/higher blower speed and heating switches to the tempera- ture that was set before the front de- froster was switched on. The indicator lamp on button 0 or, depending on vehicle production date, button | goes out. The indicator lamp on button 9 comes on.

or 왘 Turn temperature control 1

and/or 7 (컄 page 232) slightly in any direction. Heating switches to the temperature that was set before the front defroster was switched on. The indicator lamp on button 0 or, depending on vehicle production date, button | goes out. The indicator lamp on button 9 comes on.

238

Maximum cooling MAXCOOL

Air recirculation mode

If the air distribution control as well as the airflow volume control are set to U and there is a high need for cooling, the MAXCOOL function is activated. “MAXCOOL” appears in the front and rear display. This provides the fastest possible cooling of the vehicle interior (when windows and tilt/sliding sunroof* are closed).

Switch to air recirculation mode to prevent unpleasant odors from entering the vehicle from the outside (e.g. before driving through a tunnel). This setting cuts off the intake of outside air and recirculates the air in the passenger compartment.

Warning!

Fogged windows impair visibility, endangering you and others. If the windows begin to fog on the inside, switching off the air recirculation mode immediately should clear interior window fogging. If interior win- dow fogging persists, make sure the air conditioning (컄 page 241) is activated, or press button 0 or, depending on vehicle production date, button |.

Controls in detail 3-zone automatic climate control*

Activating 왘 Press button : (컄 page 232). The indicator lamp on the button comes on.

i The air recirculation mode is activated auto- matically at high outside temperatures. The indicator lamp on button : is not lit when the air recirculation mode is automatically switched on. A quantity of outside air is added after approxi- mately 30 minutes. If you have turned off the air conditioning (컄 page 241) or the outside temperature is below 41°F (5°C), the air recirculation mode will not switch on automatically.

i To cool the interior as fast as possible, the automatic climate control automatically switch- es to air recirculation. The indicator lamp on button : is not lit when the system switches to air recirculation automatically.

239

Controls in detail 3-zone automatic climate control*

Deactivating 왘 Press button : (컄 page 232). The indicator lamp on the button comes on.

i The air recirculation mode is deactivated automatically 앫 after 5 minutes if the outside temperature is

below approximately 41°F (5°C)

앫 after 5 minutes if the air conditioning and

air-drying is turned off

앫 after 30 minutes if the outside temperature

is above approximately 41°F (5°C)

At outside temperatures above 79°F (26°C) the system will not automatically switch back to outside air. A quantity of outside air is added after approximately 30 minutes.

240

Air recirculation mode with conve- nience closing and opening feature

Warning!

Never operate the side windows and tilt/sliding sunroof* if there is the possibility of anyone being harmed by the opening or closing procedure.

When using the air recirculation mode with convenience closing feature, should the up- ward movement of a window be blocked by some obstruction including but not limited to arms, hands, fingers, etc., the automatic reversal feature will not operate.

In case the procedure causes potential danger:

Vehicles with or without tilt/sliding sun- roof*: The closing of the windows can be im- mediately halted by pressing or pulling the respective window switch. The closing of the tilt/sliding sunroof* can be immediately halted by moving the switch for the tilt/slid- ing sunroof* in any direction.

The closing of the side windows and the tilt/sliding sunroof* can be reversed by again pressing and holding the : button.

Convenience closing 왘 Press button : for approximately

2 seconds. The windows and/or tilt/sliding sun- roof* will close. You can release button : once the closing proce- dure has begun. The windows and tilt/sliding sunroof* continue closing until they are fully closed. The indicator lamp on the button comes on. The air recirculation mode is activated.

Convenience opening 왘 Press button : for approximately

2 seconds. The windows and/or tilt/sliding sun- roof* will return to their previous posi- tions. You can release button : once the opening procedure has be- gun. The windows and tilt/sliding sun- roof* continue opening until they have reached their previous positions. The indicator lamp on the button goes out. The air recirculation mode is deactivat- ed.

i A window or the tilt/sliding sunroof* will only return to its previous position if it has not been moved to another position using the re- spective window switch or tilt/sliding sunroof* switch after it was closed with button :.

Air conditioning

The cooling function, only operational when the engine is running, cools the vehi- cle down to the selected interior tempera- ture. The cooling function also dehumidifies the air in the vehicle interior, thereby preventing the windows from fog- ging up.

i Condensation may drip out from underneath the vehicle. This is normal and not an indication of a malfunction.

Warning!

If you turn off the cooling function, the interior air is not dried. The windows can fog up more quickly. Window fogging may impair visibility and endanger you and others.

Controls in detail 3-zone automatic climate control*

Deactivating It is possible to deactivate the air condi- tioning (cooling) function of the automatic climate control system. The air in the vehi- cle will then no longer be cooled or dehu- midified. 왘 Press button 9 (컄 page 232).

The indicator lamp on the button goes out. The cooling function switches off after a short delay.

Activating Moist air can fog up the windows. You can dehumidify the air with the air condition- ing. 왘 Press button 9 again.

The indicator lamp on the button comes on.

The air conditioning uses the refrigerant R-134a. This refrigerant is free of CFCs which are harmful to the ozone layer.

241

Controls in detail 3-zone automatic climate control*

! If the air conditioning cannot be turned on again, this indicates that the air conditioning is losing refrigerant. The compressor has turned off. Have the air conditioning checked at the nearest authorized Mercedes-Benz Light Truck Center.

Using driver-side settings for all tem- perature zones

You can use the settings of the driver’s side, such as temperature, air volume and air distribution, for all temperature zones. These settings only need to be made once and the automatic climate control system will automatically regulate the settings for all temperature zones quickly and comfort- ably.

242

Activating 왘 Adjust the temperature, air volume and

air distribution (컄 page 232).

왘 Press button ; (컄 page 232). The indicator lamp on the button comes on. The driver-side settings are used for all temperature zones.

Deactivating 왘 Press button ; (컄 page 232) again. The indicator lamp on the button goes out.

i If you manually set the temperature, air vol- ume or air distribution for the passenger side or the rear passenger compartment when the MONO setting is active, the MONO setting will be switched off.

Residual heat and ventilation

With the engine switched off, it is possible to continue to heat or ventilate the interior for up to 30 minutes. This feature makes use of the residual heat produced by the engine.

i How long the system will provide heating depends on 앫 the coolant temperature 앫 the battery voltage Regardless of the temperature and air volume set on the automatic climate control panel, an interior temperature is aimed at by 72°F (22°C) and the blower runs on low speed to protect the vehicle battery.

Rear automatic climate control

The control panel is located at the rear of the front center console.

Activating 왘 Switch off the ignition (컄 page 41). 왘 Press button 9 (컄 page 232). The indicator lamp on the button comes on.

Deactivating 왘 Press button 9.

The indicator lamp on the button goes out.

i The residual heat is automatically turned off: 앫 when the ignition is switched on 앫 after about 30 minutes 앫 if the coolant temperature is too low 앫 if the battery voltage drops

Controls in detail 3-zone automatic climate control*

1 Left rear center air vent, adjustable 2 Right rear center air vent, adjustable