2011 Mercedes-benz G Class Owners Manual

Rear-seat heating

: Level 1 (normal heating) ; Level 2 (rapid heating) i The system automatically switches down

from level 2 (rapid heating) to level 1
(normal heating) after approximately five minutes. The system automatically switches off approximately 30 minutes after it is set to level 1.

X To select level 1: press the upper section

of button :. An indicator lamp lights up.

X To deactivate level 1: press the upper

section of button :. The indicator lamp goes out.

X Make sure that the SmartKey is in position

2 in the ignition lock.

X To switch on: press button : repeatedly

until the desired ventilation level is set. i If you open the side windows and the

sliding sunroof using the key (Y page 71), the driver's seat ventilation automatically switches to the highest level.

Steering wheel

83

When you adjust the steering wheel, make sure that: Rthe steering wheel can be reached with

your arms slightly bent.

Ryou can move your legs freely. Ryou can see all the displays in the

instrument cluster clearly.

X To switch off: press button : repeatedly

until all the indicator lamps go out.

Adjusting the steering wheel

Problems with the seat ventilation If one or all of the indicator lamps in the seat ventilation button are flashing, the seat ventilation has switched off automatically. The vehicle's electrical system voltage is too low because too many electrical consumers are switched on. X Switch off electrical consumers which you

do not need, such as the rear window defroster or interior lighting. Once the battery is sufficiently charged, the seat ventilation will switch back on automatically.

Steering wheel Important safety notes You can adjust the steering wheel electrically. G Warning! Do not adjust the steering wheel while driving. Adjusting the steering wheel while driving could cause the driver to lose control of the vehicle. The electrical steering wheel adjustment feature can be operated at any time. Therefore, do not leave children unattended in the vehicle, or with access to an unlocked vehicle. A child's unsupervised access to a vehicle could result in an accident and/or serious personal injury.

: To adjust the steering wheel position

(fore-and-aft adjustment)

; To adjust the steering wheel height X Make sure that the SmartKey is in position

1 or 2 in the ignition lock.

i If the driver's door is open, the steering wheel can be adjusted for up to 30 minutes after the ignition has been switched off.

X Press the lever in the direction of

arrow : or ; until the steering wheel is in the desired position.

You can find more information under: REASY-ENTRY/EXIT feature (Y page 84) RStoring settings (Y page 88)

Steering wheel heating Switching on/off The steering-wheel heating heats the leather areas of the steering wheel.

84

Steering wheel

: To switch on the steering-wheel heating ; Indicator lamp = To switch off the steering-wheel heating X To switch on/off: make sure that the key

is in position 1 or 2 in the ignition lock.

X Turn the lever in the direction of arrow :

or =. Indicator lamp ; lights up or goes out.

i The steering wheel heating does not

switch off automatically.

i The steering wheel heating may switch off

temporarily if: Rthe temperature of the vehicle interior is

above 86 ‡ (30 †).

Rthe temperature of the steering wheel is

above 95 ‡ (35 †).

Indicator lamp ; remains on.

i The steering wheel heating is deactivated

if you remove the SmartKey from the ignition lock.

Problems with the steering wheel heating If steering wheel heating indicator lamp ; is flashing, the steering wheel heating has switched off automatically. The vehicle's electrical system voltage is too low because too many electrical consumers are switched on. X Switch off electrical consumers which you

do not need, such as the rear window defroster or interior lighting. Once the battery is sufficiently charged, the steering wheel heating will switch back on automatically.

Steering wheel EASY-ENTRY/EXIT feature General notes The EASY-ENTRY/EXIT feature makes getting in and out of your vehicle easier. You can activate and deactivate the EASY- ENTRY/EXIT feature in the on-board computer (Y page 165).

Important safety notes G Warning You must make sure no one can become trapped or injured by the moving steering wheel when the EASY-ENTRY/EXIT feature is activated. To stop steering maneuver do one of the following: Rpress the steering column adjustment

switch.

Rpress one of the memory function position

buttons.

Rpress the memory button. Do not leave children unattended in the vehicle, or with access to an unlocked vehicle. Children could open the driver's door and unintentionally activate the EASY-ENTRY/

Mirrors

85

EXIT feature. This could result in an accident and/or serious personal injury. G Warning Let the system complete the adjustment procedure before setting the vehicle in motion. All steering wheel adjustment must be completed before setting the vehicle in motion. Driving off with the steering wheel still adjusting could cause the driver to lose control of the vehicle.

! Do not activate the EASY-ENTRY/EXIT

feature, if the seat backrest is reclined too far backwards. This can damage the front or rear seats. You must first move the backrest to a vertical position.

Position of the steering wheel when the EASY-ENTRY/EXIT feature is active The steering wheel moves upwards and towards the dashboard if: Ran easy-entry/exit steering wheel position

has been stored for the key and

Ryou remove the key from the ignition lock

or

Ryou open the driver's door with the key in

position 0 or 1 in the ignition lock.

If you insert the key into the ignition lock with the driver's door closed, the steering wheel is automatically moved to the previously set position. The last position of the steering wheel is stored when you switch off the ignition or when you store the setting with the memory function (Y page 88). i The steering wheel only moves upwards

and towards the dashboard if it has not already reached the upper end stop.

Mirrors Rear-view mirror X Adjust the rear-view mirror by hand so you

have a good overview of the traffic conditions.

Exterior mirrors Important safety notes G Warning Exercise care when using the passenger-side exterior rear view mirror. The mirror surface is convex (outwardly curved surface for a wider field of view). Objects in mirror are closer than they appear. Check your interior rear view mirror and glance over your shoulder before changing lanes.

At low outside temperatures, the exterior mirrors are heated automatically.

Adjusting the exterior mirrors The switches are located on the dashboard on the left-hand side.

X Make sure that the SmartKey is in position

1 or 2 in the ignition lock.

X Press button ; for the right-hand exterior

mirror or button = for the left-hand exterior mirror.

X Press adjustment button : up, down, to

the right or to the left until the exterior

86 Mirrors

mirror is set to a position that provides you with a good overview of traffic conditions.

You will find further information in the "Storing settings" section (Y page 88).

Exterior mirror out of position If an exterior mirror has been pushed out of position, proceed as follows: X Move the exterior mirror into the correct

position manually. The mirror housing is engaged again and you can adjust the exterior mirrors as usual (Y page 85).

Mirrors

87

Problems with the exterior mirrors Problem An exterior mirror has been pushed out of position.

Possible causes/consequences and M Solutions

X Move the exterior mirror into the correct position manually.

Automatic anti-glare mirrors G Warning! The auto-dimming function does not react if incoming light is not aimed directly at sensors in the interior rear view mirror. The interior rear view mirror and the exterior rear view mirror on the driver’s side do not react, for example, when transporting cargo which covers the rear window. Light hitting the mirror(s) at certain angles (incident light) could blind you. As a result, you may not be able to observe traffic conditions and could cause an accident.

The rear-view mirror and the exterior mirror on the driver's side automatically go into anti- glare mode if the ignition is switched on and incident light from headlamps strikes the sensor in the rear-view mirror. The mirrors do not go into anti-glare mode if reverse gear is engaged or the interior lighting is switched on.

Parking position for the exterior mirror on the front-passenger side General notes To make it easier to park, you can store the front-passenger side exterior mirror position in such a way that you can see the rear wheel on that side as soon as you engage reverse gear R. Using the memory buttons on the driver's side, you can store three parking positions per key.

Setting and storing the parking position

: Adjustment button ; Right-hand exterior mirror = Left-hand exterior mirror ? Memory button X Make sure that the vehicle is stationary and

that the key is in position 1 or 2 in the ignition lock.

X Press button ; for the exterior mirror on

the front-passenger side.

X Engage reverse gear R.

The exterior mirror on the front-passenger side moves to the preset parking position.

X Use adjustment button : to adjust the exterior mirror to a position which allows you to see the rear wheel and the curb.

X Press memory button ? and adjustment

button : within three seconds. The parking position is stored if the exterior mirror does not move.

i If the mirror moves out of position, repeat

the steps.

i If you shift the transmission to another position, the exterior mirror on the front-

88 Memory functions

passenger side returns to the driving position.

Calling up a stored parking position setting X With the key in position 2 in the ignition lock and the exterior mirror on the front- passenger side activated, engage reverse gear. The exterior mirror on the front-passenger side moves to the stored parking position.

The exterior mirror on the front-passenger side moves back to its original position: Ras soon as you exceed a speed of

10 km/h

Rabout ten seconds after you have

disengaged reverse gear R

Rif you press button = for the exterior

mirror on the driver's side

Memory functions Storing settings With the memory function, you can store up to three different settings, e.g. for three different people. The following settings are stored as a single memory preset: Rposition of the seat, backrest and head

restraint

Rdriver's side: steering wheel position Rdriver's side: position of the exterior

mirrors on the driver's and front-passenger sides G Warning Do not activate the memory function while driving. Activating the memory function while driving could cause the driver to lose control of the vehicle.

The buttons are located on the door control panel.

X Make sure that the key is in position 2 or

that the respective door is open.

X Adjust the seat (Y page 78) and head

restraint (Y page 79).

X On the driver's side, adjust the steering

wheel (Y page 83) and the exterior mirrors (Y page 85).

X Press memory button ;. X Press one of memory buttons :1, 2 or 3

within three seconds. The settings are stored in the selected storage position.

Calling up a stored setting X Press and hold the relevant memory button

1, 2 or 3, until the seat, head restraints, steering wheel and mirrors are in the stored position.

i The setting procedure is interrupted as soon as you release the memory button.

! If you want to move the seat from the fully reclined position to a stored seat position, first raise the backrest using the seat switch. The seat could otherwise be damaged.

89

Vehicle equipment .............................. 90
Exterior lighting .................................. 90
Interior lighting ................................... 94
Changing bulbs ................................... 96
Windshield wipers ............................ 101

90

Exterior lighting

Vehicle equipment

i This manual describes all the standard and optional equipment of your vehicle which was available at the time of purchase. Country-specific differences are possible. Please note that your vehicle may not be equipped with all features described. This also applies to safety- relevant systems and functions.

Exterior lighting Important safety notes For reasons of safety, Mercedes-Benz recommends that you drive with the lights switched on even during the daytime. In some countries, operation of the headlamps varies due to legal requirements and self-imposed obligations. In these countries, the daytime running lamps are automatically switched on when the engine is started.

Information about driving abroad Converting to symmetrical low beam when driving abroad: switch the headlamps to symmetrical low beam in countries in which traffic drives on the opposite side of the road to the country where the vehicle is registered. This prevents glare to oncoming traffic. Symmetrical lights do not illuminate as large an area of the edge of the road. Have the headlamps converted at a qualified specialist workshop, e.g. an authorized Mercedes-Benz Center, as close to the border as possible before driving in these countries. Converting to asymmetrical low beam after returning: have the headlamps converted back to asymmetrical low beam at a qualified specialist workshop, e.g. an authorized Mercedes-Benz Center, as soon as possible after crossing the border when returning.

Light switch Operation

1W Left-hand standing lamps 2X Right-hand standing lamps 3$ Lights off/daytime running lamps 4Ã Automatic headlamp mode/daytime

running lamps

5T Standing lamps, perimeter lamps,

license plate illumination and instrument cluster illumination

6L Low-beam/high-beam headlamps 7N Front fog lamps 8R Rear fog lamp The turn signals, high-beam headlamps and the high-beam flasher are operated using the combination switch (Y page 93). ! Switch off the standing lamps, parking

lamps and low-beam headlamps when you leave the vehicle. This prevents the battery from discharging.

The exterior lighting (except the parking lamps) switches off automatically if you: Rremove the SmartKey from the ignition lock Ropen the driver's door with the SmartKey

in position 0

If you hear a warning tone when you leave the vehicle, the lights may still be switched on. The Switch Off Lights message appears in the multifunction display. X Turn the light switch to $ or Ã.

X If you see the Turn off lights or remove key message in the multifunction display, remove the SmartKey from the ignition lock.

or X Turn the light switch to $ or Ã.

Low-beam headlamps X To switch on: turn the SmartKey to

position 2 in the ignition lock or start the engine.

X Turn the light switch to L.

The L indicator lamp in the instrument cluster lights up.

X To switch off: turn the light switch to

$.

Daytime running lamps Daytime running lamps in Canada The "daytime running lamps" function is required by law in Canada. It cannot therefore be deactivated. X Turn the light switch to $ or Ã.

When the engine is running: depending on the ambient light, the low-beam headlamps or the parking lamps are switched on. When the low-beam headlamps are switched on, the L indicator lamp in the instrument cluster lights up.

If the light switch is set to $ or Ã, you cannot activate the high-beam headlamps. However, the high-beam flasher can always be used. Turn the light switch to L when driving at night. You can switch on the high- beam headlamps in this position. When the engine is running and the vehicle is stationary: if you move the selector lever from a driving position to N or P, the low-beam headlamps go out after three minutes. When the engine is running: if you turn the light switch to T, you turn on the parking lamps and low-beam headlamps.

Exterior lighting

91

When the engine is running: if you turn the light switch to L, the manual settings take precedence over the daytime running lamps. Daytime running lamps in the USA In the USA, the daytime running lamps are deactivated upon delivery from the factory. X To switch on: activate the daytime

running lamps function in the on-board computer (Y page 164).

X Turn the light switch to $ or Ã. When the engine is on: the low-beam headlamps are switched on. The L indicator lamp in the instrument cluster lights up.

If the light switch is set to $ or Ã, you cannot switch on the high-beam headlamps in bright conditions. Turn the light switch to L. You can switch on the high-beam headlamps in this position. If the light switch is set to $, Ã or L, you can switch on the high-beam headlamps in less bright conditions. However, the high-beam flasher can always be used. Turn the light switch to L when driving at night. When the engine is running: if you turn the light switch to T or L, the manual settings take precedence over the daytime running lamps.

Automatic headlamp mode G Warning If the exterior lamp switch is set to Ã, the headlamps will not automatically come on under foggy conditions. To minimize risk to you and to others, activate headlamps by turning exterior lamp switch to L when traffic and/or ambient lighting conditions require you to do so. In low ambient lighting conditions, only switch from position à to L with the vehicle at a standstill in a safe location. Switching

92

Exterior lighting

from à to L will briefly switch off the headlamps. Doing so while driving in low ambient lighting conditions may result in an accident. The automatic headlamp feature is only an aid to the driver. The driver is responsible for the operation of the vehicle’s lights at all times.

The parking lamps, low-beam headlamps and license plate lamp are switched on or off automatically, depending on the brightness of the ambient light. X To switch on: turn the light switch to

Ã. SmartKey in position 1 in the ignition lock: the standing lamps are switched on or off automatically depending on the brightness of the ambient light. When the engine is running: depending on the ambient light, the parking lamps, the low-beam headlamps and the license plate lamp are switched on or off automatically. When the low-beam headlamps are switched on, the L indicator lamp in the instrument cluster lights up.

Canada only: if the light switch is in position $ or Ã, you cannot switch on the high- beam headlamps. However, the high-beam flasher can always be used. Turn the light switch to L when driving at night. You can switch on the high-beam headlamps in this position.

Front fog lamps and rear fog lamp Front fog lamps G Warning If you suspect that driving conditions will be foggy, turn the light switch to L before you start your journey. Your vehicle may otherwise not be visible and you could endanger yourself and others.

G Warning In low ambient lighting or foggy conditions, only switch from position à to L with the vehicle at a standstill in a safe location. Switching from à to L will briefly switch off the headlamps. Doing so while driving in low ambient lighting conditions may result in an accident.

X To switch on: turn the SmartKey to

position 2 in the ignition lock or start the engine.

X Turn the light switch to L or T. If the

light switch is set to Ã, you cannot switch on the fog lamps.

X Pull the light switch out to the first detent. The green N indicator lamp on the light switch lights up.

X To switch off: press the light switch in as

far as it will go. The green N indicator lamp on the light switch goes out.

Rear fog lamp X To switch on: turn the SmartKey to

position 2 in the ignition lock or start the engine.

X Turn the light switch to L or T. When the light switch is set to Ã, you cannot switch on the rear fog lamp.

X Pull the light switch out to the second stop. The yellow R indicator lamp on the light switch lights up.

X To switch off: press the light switch in as

far as it will go. The yellow R indicator lamp on the light switch goes out.

Combination switch Turn signal

X To indicate briefly: press the combination switch briefly to the pressure point in the direction of arrow ; or ?. The corresponding turn signal flashes three times.

X To indicate: press the combination switch beyond the pressure point in the direction of arrow ; or ?. The corresponding ! or # indicator lamp in the instrument cluster flashes.

High-beam headlamps X To switch on: turn the SmartKey to

position 2 in the ignition lock or start the engine.

X Turn the light switch to L. X Press the combination switch beyond the

pressure point in the direction of arrow :. The K indicator lamp in the instrument cluster lights up.

X To deactivate: move the combination

switch back to its normal position. The K indicator lamp in the instrument cluster goes out.

Exterior lighting

93

High-beam flasher X To switch on: turn the SmartKey in the

ignition lock to position 1 or 2 or start the engine.

X Pull the combination switch briefly in the

direction of arrow =. The K indicator lamp in the instrument cluster lights up briefly.

Hazard warning lamps

The hazard warning lamp switches on automatically if an air bag or the belt tensioners are triggered and the SmartKey is in position 1 in the ignition lock. X To switch on: press button :.

All turn signals flash. If you now switch on a turn signal using the combination switch, only the turn signal lamp on the corresponding side of the vehicle will flash.

X To switch off: press the : button. i The hazard warning lamps still operate if

the ignition is switched off.

Headlamp cleaning system The headlamps are cleaned automatically if the "Wipe with washer fluid" function is operated fifteen times while the lights are on and the engine is running (Y page 102). When you switch off the ignition, the automatic headlamp cleaning system is reset and counting is resumed from 0.

94

Interior lighting

X Drive with the headlamps switched on.

The level of moisture diminishes, depending on the length of the journey and the weather conditions (humidity and temperature).

If the level of moisture does not diminish: X Have the headlamps checked at a qualified

specialist workshop.

Interior lighting Overview of interior lighting

Front overhead control panel : t To switch the cargo compartment

lamp/rear interior lighting on/off

; p Switches the right-hand reading

lamp on/off

= Rocker switch (to control the interior

lighting)

? p Switches the left-hand reading lamp

on/off

X To switch on manually: turn the

SmartKey to position 2 in the ignition lock or start the engine.

X Briefly press button : of the headlamp

cleaning system. The headlamps are cleaned with a high- pressure water jet.

Cornering light function The cornering light function improves the illumination of the road over a wide angle in the direction you are turning, enabling better visibility in tight bends, for example. It can only be activated if the low-beam headlamps are switched on and the fog lamp is switched off. Active: if you are driving at speeds below 25 mph(40 km/h) and switch on the turn signals and turn the steering wheel. Not active: if you are driving at speeds above 25 mph(40 km/h) or switch off the turn signal and turn the steering wheel to the straight- ahead position. The cornering lamp may remain lit for a short time.

Headlamps and turn signal lamps fogged up on the inside The headlamps and the indicator lamps in the exterior mirrors may fog up on the inside if there is high atmospheric humidity.

Interior lighting

95

i If a door remains open and the SmartKey

is not in the ignition lock, the interior lighting switches off after a short while.

X To switch off: press the z symbol on

rocker switch =.

The interior lighting remain switched off even when it is dark if you: Runlock the vehicle Ropen a door Rremove the SmartKey from the ignition lock

Manual control Front interior lighting ! If the interior lighting has been switched

on manually, it will not be switched off automatically. This can cause the starter battery to discharge. Make sure that the interior lighting does not remain switched on too long after the engine has been switched off.

X To switch on: press the c symbol on

rocker switch =.

X To switch off: set rocker switch = to the

center position.

Reading lamps X To switch on/off: press the p button. Cargo compartment lamp G Warning! To prevent possible personal injury, always keep hands and fingers away from the cargo compartment opening when closing the tailgate. Be especially careful when small children are around. G Warning! Make sure the tailgate is closed when the engine is running and while driving. Among other dangers, deadly carbon monoxide (CO) gases may enter vehicle interior resulting in unconsciousness and death.

Rear-compartment overhead control panel : p Switches the right-hand reading

lamp on/off

; p Switches the left-hand reading lamp

on/off

Interior lighting control Important notes In order to prevent the vehicle's battery from discharging, the interior lighting functions are automatically deactivated after some time except for when the SmartKey is in position 2 in the ignition lock.

Automatic interior lighting control X To switch on: set rocker switch = to the

center position.

The interior lighting switches on automatically when it is dark if you: Runlock the vehicle Ropen a door Rremove the SmartKey from the ignition lock The interior light is activated for a short while when the SmartKey is removed from the ignition lock. You can activate this delayed switch-off using the on-board computer (Y page 165). When a front door is opened, the front interior lighting comes on. When a rear door is opened, the rear interior lighting comes on. In addition, the courtesy lights come on.

96

Changing bulbs

! Switch off the cargo compartment lamp if you wish to leave the rear door open for a longer period. The battery may otherwise discharge.

X To switch on/off: press the t button. i If you open the rear door, the cargo

compartment lamp comes on. Then, you cannot switch it off using the t button. Switch off the cargo compartment lamp if you wish to leave the rear door open for a longer period. This prevents the battery from discharging.

X Open the rear door. X To switch off with the rear door open: press lock : down in the direction of the arrow until it engages. The cargo compartment lamp is switched off.

! Do not close the rear door while lock : is engaged at the bottom. Otherwise, you could damage lock :.

X To switch on with the rear door open:

press lock cylinder ;. The cargo compartment lamp resumes its normal function.

Rear interior lighting X To switch on/off: press the t button. i The rear interior lighting switches on when you open a rear door. Then, you cannot switch it off using the t button.

Switch off the rear interior lighting if you wish to leave the rear doors open for a longer period. This prevents the battery from discharging.

Changing bulbs Important safety notes Xenon bulbs G Warning Xenon bulbs carry a high voltage. You could get an electric shock and be seriously or even fatally injured if you touch the electric contacts on Xenon bulbs. Therefore, never remove the cover from Xenon bulbs. Do not change Xenon bulbs yourself, but have them replaced at a qualified specialist workshop which has the necessary specialist knowledge and tools to carry out the work required. Mercedes-Benz recommends that you use an authorized Mercedes-Benz Center for this purpose. In particular, work relevant to safety or on safety-related systems must be carried out at a qualified specialist workshop.

Bulbs and lamps are an important aspect of vehicle safety. You must therefore make sure that these function correctly at all times. Have the headlamp setting checked regularly.

Other bulbs G Warning Bulbs and lamps can be very hot. You should therefore allow them to cool down before you change them. Otherwise, you could be burned if you touch them. Keep bulbs out of the reach of children. Otherwise, they could damage the bulbs, for example, and injure themselves. Never use a bulb which has been dropped. Such a bulb may break or even explode and injure you.

Changing bulbs

97

i Individual segments of the license plate

lamp LEDs may fail without a display message appearing in the multifunction display. Check the license plate lamp regularly. Consult a qualified specialist workshop if necessary.

You can replace the following bulbs: Rfog lamp/cornering light with fog lamp

function

Rturn signal lamp (front) Rbrake/tail lamp Rturn signal lamp (rear) Rtail lamp/standing lamp Rbackup lamp Rrear fog lamp Rside marker lamp

Overview: changing bulbs/bulb types

Front bulbs : Turn signal lamp: 1156 NA ; Side marker lamp: T 4 W = Cornering light function with fog lamp

function: H11 55 W

Halogen bulbs are pressurized and could explode when you change them, particularly if they are very hot. You should therefore wear eye protection and gloves when you are changing them.

There are bulbs other than the Xenon bulbs that you cannot replace. Replace only the bulbs listed (Y page 97). Have the bulbs that you cannot replace yourself changed at a qualified specialist workshop. Mercedes-Benz recommends that you use an authorized Mercedes-Benz Center for this purpose. In particular, work relevant to safety or on safety-related systems must be carried out at a qualified specialist workshop. If you require assistance changing bulbs, consult a qualified specialist workshop. Do not touch the glass tube of new bulbs with your bare hands. Even minor contamination can burn into the glass surface and reduce the service life of the bulbs. Always use a lint- free cloth or only touch the base of the bulb when installing. Only use bulbs of the correct type. If the new bulb still does not light up, consult a qualified specialist workshop. Bulbs and lamps are an important aspect of vehicle safety. You must therefore make sure that these function correctly at all times. Have the headlamp setting checked regularly.

Before changing bulbs Have the following bulbs changed at a qualified specialist workshop, e.g. an authorized Mercedes-Benz Center: Radditional turn signals in the exterior

mirrors

Rhigh-mounted brake lamp Rhigh-beam/low-beam headlamps (Xenon

bulbs)

Rparking lamp/standing lamp Rlicense plate lamp

98

Changing bulbs

X Remove screws ?. i Only remove screws ?. Do not turn

adjustment screw A. If adjustment screw A is turned, the front fog lamp adjustment must be checked at a qualified specialist workshop, e.g. an authorized Mercedes- Benz Center.

X Remove headlamp =.

Rear bulbs : Side marker lamp: T 4 W ; Tail lamps:

Turn signal lamp: PY 21 W Brake lamp/tail lamp: P 21/5 W Tail lamp/parking lamp: W 5 W

= Backup lamp: P 21 W ? License plate lamp: LEDs5
A Rear fog lamp: P 21 W

Changing the front bulbs Front fog lamps/cornering lamps with fog lamp function

X Hold headlamp =. X Lightly press bulb holder B, turn it

counter-clockwise to the stop and pull it out.

X Switch off the lights. X Remove screws :. X Remove cover ;.

5 These bulbs must be replaced at a qualified specialist workshop, e.g. an authorized Mercedes-Benz Center.

Changing bulbs

99

X Take bulb C out of bulb holder B. X Insert the new bulb into bulb holder B. X Insert bulb holder B into headlamp = and

turn it clockwise to the stop.

X Insert headlamp =. X Replace and tighten screws ?. X Position cover ;. X Replace and tighten screws :.

Turn signal X G 55 AMG: release the turn signal protection grille from the rear of the bracket and fold it forward.

! Make sure that the headlamp protection

grille does not strike against painted surfaces. You could otherwise damage the paintwork.

X Lightly press bulb =, turn it counter-

clockwise and pull it out.

X Insert the new bulb and, applying slight

pressure, turn it clockwise until it engages.

X Install lens ;. X Replace and tighten screws :. ! Do not fasten the screws too tightly. You

could otherwise damage the lens.

X G 55 AMG: fold the headlamp protection grille back and engage it into the bracket.

Side marker lamp The bulbs of the front and rear side marker lamps are changed in the same way.

X Switch off the lights. X Remove screws :. X Remove lens ;.

Front side marker lamp (example) X Switch off the lights. X Remove screws :. X Remove housing ;.

100 Changing bulbs

X Remove dust cover =. X Push the catch to the side and pull the bulb

holder with the bulb out of housing ;.

X Lightly press bulb ?, turn it counter-

clockwise and pull it out.

X Insert the new bulb and, applying slight

pressure, turn it clockwise until it engages.

X Insert the bulb holder into housing ;. X Attach dust cover =. X Insert housing ;. X Replace and tighten screws :. ! Do not fasten the screws too tightly. You

could otherwise damage the lens.

Changing the rear bulbs G 55 AMG only: headlamp protective grid You must remove the headlamp protection grille before you can change the bulbs in the tail lamps.

G 55 AMG: headlamp protection grille X Unscrew screws ;. X Swing headlamp protection grille : to the

right.

! Make sure that the headlamp protection

grille does not strike against painted surfaces. You could otherwise damage the paintwork.

X After changing the bulbs, swing headlamp

protection grille : to the left.

X Tighten screws ;.

Tail lamp

X Switch off the lights. X Remove screws :. X Remove lens ;.

Windshield wipers

101

X Switch off the lights. X Remove screws :. X Remove lens ;.

X Turn the bulb = counter-clockwise,

applying slight pressure, and remove it from the bulb holder.

X Insert the new bulb into the bulb holder and

turn it clockwise until it engages.

X Install lens ;. X Tighten screws :. ! Do not fasten the screws too tightly. You

could otherwise damage the lens.

Windshield wipers Important safety notes G Warning! Wiper blades are components that are subject to wear and tear. Replace the wiper blades twice a year, preferably in the spring and fall. Otherwise the windows will not be wiped properly. As a result, you may not be able to observe surrounding traffic conditions and could cause an accident.

! Do not operate the windshield wipers when the windshield is dry, as this could damage the wiper blades. Moreover, dust that has collected on the windshield/rear window can scratch the glass if wiping takes place when the windshield/rear window is dry.

= Turn signals ? Brake/tail lamp A Tail lamp/standing lamp X Turn the bulb counter-clockwise, applying slight pressure, and remove it from bulb holder.

X Insert the new bulb into the bulb holder and

turn it clockwise until it engages.

! When installing the lens, make sure that

the seal is positioned correctly.

X Install lens ;. X Tighten screws :. ! Do not fasten the screws too tightly. You

could otherwise damage the lens. X G 55 AMG: secure the headlamp

protection grille (Y page 100).

Backup lamp/rear fog lamp

Rear fog lamp (example)

102 Windshield wipers

If it is necessary to switch on the windshield wipers in dry weather conditions, always use washer fluid when operating the windshield wipers.

Switching the windshield wipers on/ off

Combination switch 1 III Continuous wipe, fast 2 II Continuous wipe, slow 3 I Intermittent wipe/rain sensor 4 0 windshield wipers off A í Single wipe/ î To wipe the

windshield using washer fluid

X Turn the SmartKey to position 1 or 2 in the

ignition lock.

X Turn the combination switch to the

corresponding position.

! Intermittent wiping with rain sensor: due

to optical influences and the windshield becoming dirty in dry weather conditions, the windshield wipers may be activated inadvertently. This could then damage the windshield wiper blades or scratch the windshield. For this reason, you should always switch off the windshield wipers in dry weather.

In the I position, the appropriate wiping frequency is set automatically according to the intensity of the rain. Intermittent wiping is interrupted if you stop and open a front door. This protects people

getting into and out of the vehicle from being sprayed with water. Intermittent wiping continues when all doors are closed and: Ryou shift the automatic transmission to

drive position D or reverse gear R or

Ryou change the wipe setting on the

combination switch.

Switching the rear window wiper on/ off

: è Intermittent wipe ; Indicator lamp = ô To wipe with washer fluid The rear window wiper comes on automatically if you shift the selector lever to R while the windshield wipers are on. X Turn the SmartKey to position 1 or 2 in the

ignition lock.

X To switch on intermittent wiping: push

button :. Indicator lamp ; lights up.

X To switch off intermittent wiping: push

button : again. Indicator lamp ; goes out.

X To wipe with washer fluid: push button = and hold it there until the rear window is clean. The rear window is wiped for a further five seconds after the button is released.

Windshield wipers

103

Replacing the wiper blades Important safety notes G Warning! For safety reasons, switch off the wipers and remove the SmartKey from the starter switch before replacing a wiper blade. Otherwise, the wiper motor could suddenly turn on and cause injury.

! To avoid damaging the wiper blades,

make sure that you touch only the wiper arm of the wiper.

! Never open the hood if a windshield wiper

arm has been folded away from the windshield. Never fold a windshield wiper arm without a wiper blade back onto the windshield/ rear window. Hold the windshield wiper arm firmly when you change the wiper blade. If you release the windshield wiper arm without a wiper blade and it falls onto the windshield, the windshield may be damaged by the force of the impact. Mercedes-Benz recommends that you have the wiper blades replaced by a qualified specialist workshop, e.g. at an authorized Mercedes-Benz Center.

Removing the wiper blade X Remove the SmartKey from the ignition

lock.

X Fold the wiper arm away from the

windshield until it engages.

X Position the wiper blade at right angles.

X Press locking spring :. X Slide wiper blade = with hinge piece ?

from wiper arm ;.

Installing the wiper blade

: Locking spring ; Wiper arm = Wiper blade ? Hinge piece X Slide new wiper blade = with the recess

onto wiper arm ;.

X Engage locking spring : into the end of

the wiper arm.

X Make sure that wiper blade = is seated

correctly.

X Fold wiper arm ; back onto the

windshield.

104 Windshield wipers

Problems with the windshield wipers The windshield wipers are obstructed Leaves or snow, for example, may be obstructing the windshield wiper movement. The wiper motor has been deactivated. X For safety reasons, you should remove the

SmartKey from the ignition lock.

X Remove the cause of the obstruction. X Switch the windshield wipers back on.

The windshield wipers are inoperative The windshield wiper drive is malfunctioning. X Select another wiper speed on the

combination switch.

X Have the windshield wipers checked at a

qualified specialist workshop.

Vehicle equipment ............................ 106
Overview of climate control sys- tems ................................................... 106
Operating the climate control sys- tem ..................................................... 107
Setting the air vents ......................... 112

105

106 Overview of climate control systems

This will speed up the cooling process and the desired vehicle interior temperature will be reached more quickly.

i The integrated filter can filter out most

particles of dust and completely filters out pollen. A clogged filter reduces the amount of air supplied to the vehicle interior. For this reason, you should always observe the interval for replacing the filter, which is specified in the Service Booklet. As it depends on environmental conditions, e.g. heavy air pollution, the interval may be shorter than stated in the Service Booklet.

Vehicle equipment

i This manual describes all the standard and optional equipment of your vehicle which was available at the time of purchase. Country-specific differences are possible. Please note that your vehicle may not be equipped with all features described. This also applies to safety- relevant systems and functions.

Overview of climate control systems Important safety notes G Warning Severe conditions (e.g. strong air pollution) may require replacement of the filter before its scheduled replacement interval. A clogged filter will reduce the air volume to the interior and the windows could fog up, impairing visibility and endangering you and others. Have a clogged filter replaced as soon as possible at an authorized Mercedes-Benz Center. G Warning Follow the recommended settings for heating and cooling given on the following pages. Otherwise, the windows could fog up, impairing visibility and endangering you and others.

Automatic climate control controls the temperature and the humidity in the vehicle interior and filters undesirable substances from the air. Automatic climate control is only operational when the engine is running6. Optimum operation is only achieved when you drive with the side windows and the sliding sunroof closed. i Ventilate the vehicle for a brief period

during warm weather, e.g. using the convenience opening feature (Y page 71).

6 The "residual heat" function can only be switched on/off if the ignition is switched off.

Operating the climate control system 107

Control panel for THERMATIC automatic climate control (2-zone)

: To increase/reduce the airflow (Y page 110) To switch climate control on/off (Y page 108)