Login- Download PDF Manual
-
played, the next CD will automatically be selected and played.
button. The next track on the CD will be
Skipping tracks forwards/backwards Press the played. Press the button. If the track has been playing for more than 10 seconds, it will revert to the start of that track. If it has been playing for less than ten seconds it will revert to the preceding track. To skip several tracks, the respective button must be pressed until the desired track is reached. If the beginning or end of the CD is reached during the search, the first or last track will be played.
Fast forward/reverse Press the forward. Press the reverse.
button and hold it down for audible fast
button and hold it down for audible
The search will stop when the button is released. The relative time of the track will be displayed during the search. The search mode will
cancel if the beginning or end of the CD is reached.
Scanning Press the SC key. Each track will be played for 8 seconds in ascending order. The search will stop at the track in question if the “SC” key is pressed.
buttons or the
J_C208_II.book Seite 143 Donnerstag, 31. Mai 2001 10:13 10
Random play/repeat function The tracks of the current CD are played in random order when the random feature (RDM) is selected. Press the RDM key to switch on, and press RDM again to switch off.
Direct track selection Tracks can be selected directly using the buttons on the alpha-numeric keypad. Press the “ function button, followed by the track number.
When the repeat function (RPT) has been selected, a particular track can be played for as many times as desired. Press the RPT key to switch
on, and press RPT again to switch off.
Note: Both functions cannot be used simultaneously.
Audio system
Instruments and controls
Operation
Driving
Instrument cluster display
Practical hints
Car care
Technical
data
Index
143
J_C208_II.book Seite 144 Donnerstag, 31. Mai 2001 10:13 10
Instruments and controls
Audio system
Operation
Driving
Instrument cluster display
Practical hints
Car care
Technical
data
Index
Telephone operation Various functions of the Mercedes-Benz integrated cellular telephone 1 can be performed and displayed via the car radio. Further instructions for operating the car telephone can be found in the operation guide for the cellular telephone 1.
Switching the telephone on and off
Switching on: Press the
button, “TEL” appears in the corner of the display. Switching off: Press and hold
button until the telephone symbol “TEL” no
the longer appears in the display, or press the “PWR” button on the phone’s keypad.
1 Optional equipment
144
Entering telephone number and starting dialing process
Enter the desired telephone number using the alpha- numeric keypad. The number can have up to 32 digits, but only 13 of these can be
displayed. The dialing process is started by pressing the SND button. The entered number can be corrected using the “CLR” key.
Press the CLR key briefly - and the last digit will be deleted. Press the CLR key longer - and
the complete number will be deleted.
Calling up the phone book The numbers stored in the telephone memory can be called up via either name or number entries. The memory contents from the portable phone must be downloaded and the telephone menu must be selected in order to call up the phone book. Refer to the “Memory download” section of the cellular telephone operation guide for more information.
J_C208_II.book Seite 145 Donnerstag, 31. Mai 2001 10:13 10
Switching between name search and number search Press ABC key - Name search Press NUM key - Number search
Placing a call
When a number or a name has been selected using the method described above, press the SND key.
Manual repeat dialing (redial) The last number entered can be re-selected by pressing the SND key once and the call can be placed by pressing the SND key a second time. The last dialed telephone number is shown on the display. Using the
button, the numbers stored in the re-dial
or
memory of the telephone can be selected.
The abbreviation L and the number in the memory are shown in the top line of the display.
Searching and selecting phone book entries by name Press the ABC key. The current name is shown on the display. The stored entries in alphabetical order can be selected using the button. By pressing the buttons, the stored entries can be selected
or
or
according to alphabetical initial letters (e.g. A-Adam, B-Brown, M-Miller).
Searching and selecting phone book entries by number Press the NUM key. The current number is shown on the display. The stored entries can be selected in numerical order using the pressing the can be selected in increments of 5 (e.g. Entry no. 2, Entry no. 7, etc.).
buttons, the stored entries
button. By
or
or
Audio system
Instruments and controls
Operation
Driving
Instrument cluster display
Practical hints
Car care
Technical
data
Index
145
J_C208_II.book Seite 146 Donnerstag, 31. Mai 2001 10:13 10
Instruments and controls
Audio system
Operation
Driving
Instrument cluster display
Practical hints
Car care
Technical
data
Index
146
Component malfunctions The radio, CD changer1, and Mercedes-Benz integrated cellular telephone1 are part of a fiberoptic networked system. Failure of one of the components can lead to malfunctions of the other components. Please contact your authorized Mercedes-Benz Center or call 1-800-FOR-MERCedes for more information in the event of a malfunction.
1 Optional equipment
Accepting incoming call in telephone mode With an incoming call, the ringing tone will be heard and the message “CALL” appears in the display. Press the SND key to answer the call.
Accepting incoming call in tape, CD or radio mode If the telephone is activated in the background (telephone symbol in the display), then a switch is made automatically to telephone when an incoming call is received. The audio source is muted, the ringing tone is heard and the message “CALL” appears. After the call has been terminated, the previously selected audio source is resumed.
Terminating call A current call can be terminated by pressing the END key.
J_C208_II.book Seite 147 Donnerstag, 31. Mai 2001 10:13 10
Power windows
Power window switches located on center console
P54.25-2031-26
Turn electronic key in steering lock to position 1 or 2. Press switch in to resistance point: k to open j to close
Release switch when window is in desired position.
Warning! When closing the windows, be sure that there is no danger of anyone being harmed by the closing procedure. In case of obstruction, the automatic reversal will not operate if a window is being closed by pressing the switch to its resistance point and holding it there, or when using the remote control. The closing procedure can be immediately reversed by either pressing the switch k or pressing button Πon the remote control, and holding it. When leaving the vehicle, always remove the electronic key from the steering lock, and lock the vehicle. Do not leave children unattended in the vehicle, or with access to an unlocked vehicle. Unsupervised use of vehicle equipment can cause serious personal injury.
Interior equipment
147
Instruments and controls
Operation
Driving
Instrument cluster display
Practical hints
Car care
Technical
data
Index
J_C208_II.book Seite 148 Donnerstag, 31. Mai 2001 10:13 10
Instruments and controls
Operation
Driving
Instrument cluster display
Practical hints
Car care
Technical
data
Index
Interior equipment
148
Express opening and closing of front door windows Press switch k or j past resistance point and release — window opens or closes completely. To interrupt procedure, briefly press k or j. If the upward movement of the window is blocked during the closing procedure, the window will stop during the last few inches before closure and open slightly. When pressing and holding the switch j to close the window, and upward movement of the window is blocked during the last few inches before closure, it will stop but not open slightly.
Warning! When leaving the vehicle, always remove the electronic key from the steering lock and lock the vehicle. Do not leave children unattended in the vehicle, or with access to an unlocked vehicle. Unsupervised use of vehicle equipment can cause serious personal injury.
Note: The power windows can also be opened or closed with the infrared remote control while unlocking or locking the vehicle doors or trunk, see page 31. If the express closing function of the door windows is interrupted, press and hold the switch j to close the window completely. The automatic full closing procedure of the window should now be reactivated.
Synchronizing power windows If the power supply was interrupted (battery disconnected or low), the windows cannot be opened or closed by the express feature. To resynchronize the express feature, press j side of power window switch until the window is completely closed and hold for additional 2 seconds. Repeat procedure for each window. The automatic full opening and closing procedure of the windows should now be restored.
J_C208_II.book Seite 149 Donnerstag, 31. Mai 2001 10:13 10
Sliding/pop-up roof (optional on model CLK 430, standard on model CLK 55 AMG)
1 to slide roof open 2 to slide roof closed 3 to raise roof at rear 4 to lower roof at rear
Turn electronic key in steering lock to position 1 or 2. The switch is illuminated when the exterior lamps are switched on (except standing lamps).
Warning! When closing the sliding/pop-up roof, be sure that there is no danger of anyone being harmed by the closing procedure. The closing procedure can be immediately reversed by either moving the switch in direction (1) or (3) or pressing button Πon the remote control, and holding it.
Notes: The sliding/pop-up roof can be opened or closed manually should an electrical malfunction occur, see page 286. The sliding/pop-up roof can also be closed with the infrared remote control while locking the vehicle doors or trunk, see page 31.
Interior equipment
149
Instruments and controls
Operation
Driving
Instrument cluster display
Practical hints
Car care
Technical
data
Index
J_C208_II.book Seite 150 Donnerstag, 31. Mai 2001 10:13 10
Instruments and controls
Operation
Driving
Instrument cluster display
Practical hints
Car care
Technical
data
Index
Interior equipment
150
Synchronizing sliding/pop-up roof If the power supply was interrupted (battery disconnected or low), or if the sliding/pop-up roof is blocked during closing/opening procedure, the system has to be synchronized. To do so, turn electronic key in steering lock to position 2, move and hold switch in direction (3) until the sliding/pop-up roof is completely raised at rear, and hold for additional 1 second.
With the roof closed or tilted open, a screen can be slid into the roof opening to guard against sun rays. When sliding the roof open, the screen will also retract.
P68.00-2101-26
Express opening of sliding/pop-up roof Move switch past resistance point and release — the sliding/pop-up roof slides open automatically. To interrupt procedure, briefly move switch in any direction.
J_C208_II.book Seite 151 Donnerstag, 31. Mai 2001 10:13 10
Interior lighting
1 Automatic interior lighting
Press once and the automatic interior lighting is activated. Interior lamps are switched on, and off (soft fade) delayed, when unlocking or locking the vehicle, or when opening or closing a door. However, there will be no (soft fade) delay when the electronic key is in steering lock position 2. Press again and interior lamps remain switched off, even when centrally unlocking or opening a door.
Interior equipment
151
2 Press to switch interior and reading lamps on or off. 3 Press to switch rear passenger compartment lamp
on or off.
4 Press to switch reading lamp on or off.
Entrance lamps, exit lamps in doors The lamps are switched on and off by the door contact switches.
Note: To prevent the vehicle battery from being discharged, with doors open all interior lamps go out after approximately 5 minutes.
Instruments and controls
Operation
Driving
Instrument cluster display
Practical hints
Car care
Technical
data
Index
J_C208_II.book Seite 152 Donnerstag, 31. Mai 2001 10:13 10
Instruments and controls
Operation
Driving
Instrument cluster display
Practical hints
Car care
Technical
data
Index
Interior equipment
152
Rear window sunshade (optional on model CLK 430, standard CLK 55 AMG)
Sun visors
The switch is located on the center console. Turn electronic key in steering lock to position 1 or 2.
P54.25-2032-26
1 Hold to raise 2 Hold to lower
Always raise the sunshade fully for its support against the window frame.
Swing sun visors down to protect against sun glare. If sunlight enters through a side window, disengage visor from inner mounting, pivot it to the side, and slide it to the desired position.
J_C208_II.book Seite 153 Donnerstag, 31. Mai 2001 10:13 10
Illuminated vanity mirrors
Interior
Warning! To help avoid personal injury during a collision or sudden maneuver, exercise care when stowing things. Put luggage or cargo in the trunk if possible. Do not pile luggage or cargo higher than the seat backs. Do not place anything on the shelf below the rear window. Luggage nets cannot secure hard or heavy objects.
Storage compartments, armrest and cup holder
Warning! Keep compartment lids closed. This will help to prevent stored objects from being thrown about and injuring vehicle occupants during an accident and sudden maneuvers.
With the visor engaged in its inner mounting, the lamp is switched on by opening the cover.
Warning! Do not use the vanity mirror while driving.
The lamp goes out automatically after approximately 5 minutes.
Interior equipment
153
Instruments and controls
Operation
Driving
Instrument cluster display
Practical hints
Car care
Technical
data
Index
J_C208_II.book Seite 154 Donnerstag, 31. Mai 2001 10:13 10
Instruments and controls
Operation
Driving
Instrument cluster display
Practical hints
Car care
Technical
data
Index
Interior equipment
Glove box
154
Storage compartments in center console
P68.00-2067-26
1 Unlocking: Turn mechanical key to vertical position
and remove.
2 Locking: Turn mechanical key to the right and
remove.
3 Opening: Pull on handle.
The glove box can be locked and unlocked with the mechanical key. See page 25 for instructions on how to remove the mechanical key from the electronic key (e.g. for valet parking service).
To open compartment in armrest: Press button (4) and lift lid. To open compartment under armrest: Press button (5) and lift lid. To close: Lower lid until it engages in lock. To open cover: Touch top of cover (6) slightly. The cover opens automatically.
J_C208_II.book Seite 155 Donnerstag, 31. Mai 2001 10:13 10
Cup holder in center console
To open cup holder: Briefly press button (7). The cup holder opens automatically. To store cup holder: Push button (7) down until cup holder engages. Close cover (6).
Notes: The right claw is adjustable to accommodate most container sizes. An additional second (smaller size) container can be placed in the cup holder. Spilling liquids (e.g. soda or coffee) could restrict the movement of the claw. Refer to page 296 for cleaning the cup holder.
Caution! Keep cup holder closed while traveling. Place only containers that fit into the cup holder to prevent spills. Do not fill containers to a height where the contents could spill during vehicle maneuvers, especially hot liquids.
Interior equipment
155
Instruments and controls
Operation
Driving
Instrument cluster display
Practical hints
Car care
Technical
data
Index
J_C208_II.book Seite 156 Donnerstag, 31. Mai 2001 10:13 10
Instruments and controls
Operation
Driving
Instrument cluster display
Practical hints
Car care
Technical
data
Index
Interior equipment
156
Cup holder in rear bench armrest
Caution! Keep cup holders closed while traveling. Place only containers that fit into the cup holder to prevent spills. Do not fill containers to a height where the contents could spill during vehicle maneuvers, especially hot liquids.
Briefly press drawer (1) and pull out to its detent.
J_C208_II.book Seite 157 Donnerstag, 31. Mai 2001 10:13 10
Ashtrays
Center console, front By touching the bottom of the cover lightly, the ashtray opens automatically.
Prior to removing the ashtray insert, move the gear selector lever to position “N”.
Warning! Remove front ashtray only with vehicle standing still. With the gear selector lever in position “N”, turn off the engine and set the parking brake. Otherwise the vehicle might move as a result of unintended contact with the gear selector lever.
To remove ashtray: Push sliding knob (1) toward the right to eject the insert.
To install ashtray: Install insert into ashtray frame and push down to engage.
Interior equipment
157
Instruments and controls
Operation
Driving
Instrument cluster display
Practical hints
Car care
Technical
data
Index
J_C208_II.book Seite 158 Donnerstag, 31. Mai 2001 10:13 10
Instruments and controls
Operation
Driving
Instrument cluster display
Practical hints
Car care
Technical
data
Index
Interior equipment
Rear seats
158
To remove ashtray: Push cover (2) down and pull out insert (3).
To install ashtray: Push ashtray down to engage.
J_C208_II.book Seite 159 Donnerstag, 31. Mai 2001 10:13 10
Lighter
Turn electronic key in steering lock to position 1 or 2. Push in lighter (1); it will pop out automatically when hot.
Warning! Never touch the heating element or sides of the lighter, they are extremely hot, hold at knob only. When leaving the vehicle always remove the electronic key from the steering lock. Do not leave children unattended in the vehicle, or with access to an unlocked vehicle. Unsupervised use of vehicle equipment may cause serious personal injury.
The lighter socket can be used to accommodate electrical accessories up to maximum 85 W.
Interior equipment
159
Instruments and controls
Operation
Driving
Instrument cluster display
Practical hints
Car care
Technical
data
Index
J_C208_II.book Seite 160 Donnerstag, 31. Mai 2001 10:13 10
Instruments and controls
Operation
Driving
Instrument cluster display
Practical hints
Car care
Technical
data
Index
Interior equipment
160
Enlarged cargo area – split folding rear seat backrest
1 Locking handle, left backrest 2 Locking handle, right backrest 3 Pass-through The two sections can be folded down separately to enlarge the cargo area.
4 Indicator, right backrest lock, visible in unlocked
position
5 Indicator, left backrest lock, visible in unlocked
position
J_C208_II.book Seite 161 Donnerstag, 31. Mai 2001 10:13 10
Fold down: Pull locking handle and fold backrest forward.
Set up: Pull backrest up until it locks in its upright position. Check for secure locking by pushing and pulling on the backrest.
Warning! Always lock backrest in its upright position when rear seat bench is occupied by passengers, cargo is being carried in the trunk, or the extended cargo area is not in use.
Note: To prevent unauthorized persons from access to the trunk, always lock backrest in its upright position.
Interior equipment
161
Instruments and controls
Operation
Driving
Instrument cluster display
Practical hints
Car care
Technical
data
Index
J_C208_II.book Seite 162 Donnerstag, 31. Mai 2001 10:13 10
Instruments and controls
Operation
Driving
Instrument cluster display
Practical hints
Car care
Technical
data
Index
Interior equipment
162
Loading instructions
P82.55-2002-26
The total load weight including vehicle occupants and luggage/cargo should not exceed the vehicle capacity weight indicated on the certification label which can be found on the left door pillar.
The handling characteristics of a fully loaded vehicle depend greatly on the load distribution. It is therefore recommended to load the vehicle according to the illustrations shown, with the heaviest items being placed towards the front of the vehicle. Always place items being carried against front or rear seat backrests, and fasten them as securely as possible. The heaviest portion of the cargo should always be kept as low as possible since it influences the handling characteristics of the vehicle.
Notes: The trunk is the preferred place to carry objects. The enlarged cargo area should only be used for items which do not fit in the trunk alone.
J_C208_II.book Seite 163 Donnerstag, 31. Mai 2001 10:13 10
Warning! In an accident, during hard braking or sudden maneuvers, loose items will be thrown around inside the vehicle, and can cause injury to vehicle occupants unless the items are securely fastened in the vehicle. To help avoid personal injury during a collision or sudden maneuver, exercise care when stowing things. Put luggage or cargo in the trunk if possible. Do not pile luggage or cargo higher than the seat backs. Do not place anything on the shelf below the rear window. Never drive vehicle with trunk lid open while pass- through is not closed and seat backrest sections not locked in their upright positions. Deadly carbon monoxide (CO) gases may enter vehicle interior resulting in unconsciousness and death.
Cargo tie down rings
1 Ring Carefully secure cargo by applying even load on all four rings with rope of sufficient strength to hold down the cargo.
Interior equipment
163
Instruments and controls
Operation
Driving
Instrument cluster display
Practical hints
Car care
Technical
data
Index
J_C208_II.book Seite 164 Donnerstag, 31. Mai 2001 10:13 10
Instruments and controls
Telephone
Operation
Driving
Instrument cluster display
Practical hints
Car care
Technical
data
Index
Parcel net in front passenger footwell A small convenience parcel net is located in the front passenger footwell. It is for small and light items, such as road maps, mail, etc..
Warning! Do not place heavy or fragile objects, or objects having sharp edges, in the parcel net. In an accident, during hard braking or sudden maneuvers, they could be thrown around inside the vehicle, and cause injury to vehicle occupants.
Note: With large objects stored in the parcel net do not slide the seat fully forward, it could damage them.
164
Telephone, general
Warning! A driver’s attention to the road must always be his/ her primary focus when driving. For your safety and the safety of others, we recommend that you pull over to a safe location and stop before placing or taking a telephone call. If you choose to use the telephone while driving, please use the hands-free device and only use the telephone when road and traffic conditions permit. Some jurisdictions prohibit the driver from using a cellular telephone while driving a vehicle. Bear in mind that at a speed of just 30 mph (approximately 50 km/h), your vehicle is covering a distance of approximately 50 feet (approximately 14 m) every second. Never operate radio transmitters equipped with a built-in or attached antenna (i.e. without being connected to an external antenna) from inside the vehicle while the engine is running. Doing so could lead to a malfunction of the vehicle’s electronic system, possibly resulting in an accident and personal injury.
J_C208_II.book Seite 165 Donnerstag, 31. Mai 2001 10:13 10
Cellular telephone The vehicle is prepared for the installation of a cellular telephone. For further information and installation contact your authorized Mercedes-Benz Center.
Warning! Some jurisdictions prohibit the driver from using a cellular telephone while driving a vehicle. Whether or not prohibited by law, for safety reasons, the driver should not use the cellular telephone while the vehicle is in motion. Stop the vehicle in an safe location before answering or placing a call.
Telephone
Instruments and controls
Operation
Driving
Instrument cluster display
Practical hints
Car care
Technical
data
Index
165
J_C208_II.book Seite 166 Donnerstag, 31. Mai 2001 10:13 10
Instruments and controls
Operation
Driving
Instrument cluster display
Practical hints
Car care
Technical
data
Index
Garage door opener
166
Garage door opener
1 Signal transmitter keys 2 Indicator lamp 3 Portable remote control transmitter
The built-in remote control is capable of operating up to three separately controlled objects.
Warning! When programming a garage door opener, the door moves up or down. When programming or operating the remote control make sure there is no possibility of anyone being harmed by the moving door.
Notes: Certain types of garage door openers are incompatible with the integrated opener. If you should experience difficulties with programming the transmitter, contact your authorized Mercedes-Benz Center, or call Mercedes-Benz Customer Assistance Center (in the USA only) at 1-800-FOR-MERCedes, or Customer Service (in Canada) at 1-800-387-0100.
J_C208_II.book Seite 167 Donnerstag, 31. Mai 2001 10:13 10
For operation in the USA only: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any unauthorized modification to this device could void to the user’s authority to operate the equipment.
Programming or reprogramming the integrated remote control:
1. Turn electronic key in steering lock to position 1
or 2.
2. Hold the end of the hand-held transmitter of the
device you wish to train approximately 2 to 5 inches (5 cm to 12 cm) away from the surface of the integrated remote control located on the inside rear view mirror, keeping the indicator lamp in view.
3. Using both hands, simultaneously push the hand- held transmitter button and the desired integrated remote control button. Do not release the buttons until completing step 4.
4. The indicator lamp on the integrated remote control
will flash, first slowly and then rapidly. When the indicator lamp flashes rapidly, both buttons may be released (the rapid flashing lamp indicates successful programming of the new frequency signal). To program the remaining two buttons, follow steps 1 though 4.
Note: If after repeated attempts, you do not successfully program the integrated remote control device to learn the signal of the hand-held transmitter, the garage door opener could be equipped with the “rolling code feature”.
Garage door opener
167
Instruments and controls
Operation
Driving
Instrument cluster display
Practical hints
Car care
Technical
data
Index
J_C208_II.book Seite 168 Donnerstag, 31. Mai 2001 10:13 10
Instruments and controls
Operation
Driving
Instrument cluster display
Practical hints
Car care
Technical
data
Index
Garage door opener
168
Rolling code programming: To train a garage door opener (or other rolling code devices) with the rolling code feature, follow these instructions after completing the “Programming” portion of this text. (A second person may make the following training procedures quicker and easier.)
1. Locate training button on the garage door opener
motor head unit. Exact location and color of the button may vary by garage door opener brand. If there is difficulty locating the transmitting button, reference to garage door opener operator’s manual. 2. Press “training” button on the garage door opener
motor head unit (which activated the “training light”). Note: Following step 2, there are 30 seconds to initiate step 3.
3. Firmly press and release the programmed
integrated remote control transmit button. Press and release same button a second time to complete the training process. (Some garage door openers may require you to do this procedure a third time to complete the training.)
4. Confirm the garage door operation by pressing the
programmed button on the integrated remote control transmitter.
Canadian programming: During programming, your hand-held transmitter may automatically stop transmitting. Continue to press and hold the integrated remote control transmitter button (note steps 2 through 4 in the “Programming” portion) while you press and re-press (“cycle”) your hand-held transmitter every two seconds until the frequency signal has been learned. The indicator lamp will flash slowly and then rapidly after several seconds upon successful training.
J_C208_II.book Seite 169 Donnerstag, 31. Mai 2001 10:13 10
Operation of remote control:
Erasing the remote control memory:
1. Turn electronic key in steering lock to position 1
or 2.
1. Turn electronic key in steering lock to position 1
or 2.
2. Select and press the appropriate button to activate the remote controlled device. The integrated remote control transmitter continues to send the signal as long as the button is pressed – up to 20 seconds.
2. Simultaneously holding down the left and right side
buttons for approximately 20 seconds, or until the control lamp blinks rapidly, will erase the codes of all three channels.
Garage door opener
169
Instruments and controls
Operation
Driving
Instrument cluster display
Practical hints
Car care
Technical
data
Index
Operation
Driving
Instrument cluster display
Practical hints
Car care
Technical
data
Index
170
J_C208_II.book Seite 170 Donnerstag, 31. Mai 2001 10:13 10
Instruments and controls
Ski sack
Ski sack (optional on model CLK 430)
P91.10-2056-26
P91.10-2061.26
Unfolding and loading
1. Fold armrest (1) down. 2. Swing cover (2) down. 3. Pull ski sack into passenger compartment and
unfold.
4. Swing flap (3) in trunk up (a magnet will hold flap
in its top position).
5. Slide skis into ski sack.
Warning! The ski sack is designed for up to two pairs of skis. Do not load the ski sack with other objects. Always fasten the ski sack securely. In an accident, an unfastened ski sack can cause injury to vehicle occupants.
J_C208_II.book Seite 171 Donnerstag, 31. Mai 2001 10:13 10
P91.10-2063-26
6. Wrap strap around ski sack and armrest (4). 7. Close clasp (arrow up) and pull strap (5) tight
(arrow down) to immobilize skis.
8. Connect snap hook (6) of front strap to eye (7)
located on center tunnel in front of rear seat bench.
Ski sack
Instruments and controls
Operation
Driving
Instrument cluster display
Practical hints
Car care
Technical
data
Index
171
J_C208_II.book Seite 172 Donnerstag, 31. Mai 2001 10:13 10
Instruments and controls
Ski sack
Operation
Driving
Instrument cluster display
Practical hints
Car care
Technical
data
Index
172
P91.10-2048-26
P91.10-2058-26
Unloading and folding
1. Loosen strap, open clasp by pressing tabs (arrows)
together, and unload skis.
2. Close flap in trunk. 3. Disconnect snap hook from eye located on center
tunnel in front of rear seat bench.
4. Fold and flatten ski sack lengthwise. 5. Wrap strap with snap hook around ski sack. 6. Fold back the reinforced ski sack tip (8), then
continue to roll up the ski sack tightly.
J_C208_II.book Seite 173 Donnerstag, 31. Mai 2001 10:13 10
7. Place rear strap in fold of ski sack.
8. Place folded ski sack inside recess of backrest.
P91.10-2060-26
P91.10-2057-26
Ski sack
Instruments and controls
Operation
Driving
Instrument cluster display
Practical hints
Car care
Technical
data
Index
173
J_C208_II.book Seite 174 Donnerstag, 31. Mai 2001 10:13 10
Instruments and controls
Ski sack
Operation
Driving
Instrument cluster display
Practical hints
Car care
Technical
data
Index
174
Removal of ski sack For removal of ski sack we recommend that you contact an authorized Mercedes-Benz Center.
Warning! Never drive vehicle with trunk lid open while the ski sack is removed. Deadly carbon monoxide (CO) gases may enter vehicle interior resulting in unconsciousness and death.
9. Close ski sack compartment cover.
P91.10-2059-26
Note: To prevent unauthorized persons from obtaining access to the trunk, always close the pass-through.
J_C208_II.book Seite 175 Donnerstag, 31. Mai 2001 10:13 10
Driving
Control and operation of
radio transmitters ..................... 176
The first 1 000 miles
(1 500 km) .................................177
Maintenance ...................................177
Catalytic converter ........................ 178
Emission control ............................179
Tele Aid ........................................... 180
Steering lock ................................... 190
Starting and turning offthe engine .................................. 192
Automatic transmission ............... 193
Parking brake .................................202Cruise control ................................. 212
Brake assist system(BAS) ........................................... 214
Antilock brake system
(ABS) ........................................... 216
Electronic stability program
(ESP) ........................................... 218
What you should know
at the gas station .......................222
Check regularly and
before a long trip ......................224
Driving instructions ...................... 203
Drive sensibly – save fuel ........ 203
Drinking and driving ................ 203
Pedals .......................................... 203
Power assistance ........................ 204
Brakes .......................................... 204
Driving off ................................... 205
Parking ........................................ 206
Tires ............................................. 206
Snow chains ............................... 209
Winter driving instructions ................................ 209
Deep water ...................................210
Passenger compartment ............211
Traveling abroad .........................211Contents – Driving
175
Instruments and controls
Operation
Driving
Instrument cluster display
Practical hints
Car care
Technical
data
Index
J_C208_II.book Seite 176 Donnerstag, 31. Mai 2001 10:13 10
Instruments and controls
Operation
Driving
Instrument cluster display
Practical hints
Car care
Technical
data
Index
Control and operation of radio transmitters
176
Control and operation of radio transmitters COMAND, radio and telephone
Telephones and two-way radio
Warning! Please do not forget that your primary responsibility is to drive the vehicle. Only operate the COMAND (Cockpit Management and Data System), radio or telephone1 if road and traffic conditions permit. Bear in mind that at a speed of just 30 mph (approximately 50 km/h), your vehicle is covering a distance of approximately 50 feet (approximately 14 m) every second.
1 Observe all legal requirements.
Warning! Never operate radio transmitters equipped with a built-in or attached antenna (i.e. without being connected to an external antenna) from inside the vehicle while the engine is running. Doing so could lead to a malfunction of the vehicle’s electronic system, possibly resulting in an accident and personal injury.
Radio transmitters, such as a portable telephone or a citizens band unit should only be used inside the vehicle if they are connected to an antenna that is installed on the outside of the vehicle. Refer to the radio transmitter operation instructions regarding use of an external antenna.
J_C208_II.book Seite 177 Donnerstag, 31. Mai 2001 10:13 10
The first 1 000 miles (1 500 km) The more cautiously you treat your vehicle during the break-in period, the more satisfied you will be with its performance later on. Therefore, drive your vehicle during the first 1 000 miles (1 500 km) at moderate vehicle and engine speeds. During this period, avoid heavy loads (full throttle driving) and excessive engine speeds. Avoid accelerating by kickdown. It is not recommended to brake the vehicle by manually shifting to a lower gear. We recommend that you select positions “3”, “2” or “1” only at moderate speeds (for hill driving). After 1 000 miles (1 500 km) speeds may be gradually increased to the permissible maximum.
Maintenance We strongly recommend that you have your vehicle serviced by your authorized Mercedes-Benz Center, in accordance with the Service Booklet at the times called for by the FSS. Failure to have the vehicle maintained in accordance with the Service Booklet at the designated times/ mileage may result in vehicle damage not covered by the Mercedes-Benz Limited Warranty. For information on the Flexible service system (FSS), see page 111.
The first 1 000 miles
177
Instruments and controls
Operation
Driving
Instrument cluster display
Practical hints
Car care
Technical
data
Index
J_C208_II.book Seite 178 Donnerstag, 31. Mai 2001 10:13 10
Instruments and controls
Operation
Driving
Instrument cluster display
Practical hints
Car care
Technical
data
Index
Catalytic converter
178
Catalytic converter Your Mercedes-Benz is equipped with monolithic type catalytic converters, an important element in conjunction with the oxygen sensors to achieve substantial control of the pollutants in the exhaust emissions. Keep your vehicle in proper operating condition by following our recommended maintenance instructions as outlined in your Service Booklet.
Caution! To prevent damage to the catalytic converters, use only premium unleaded gasoline in this vehicle. Any noticeable irregularities in engine operation should be repaired promptly. Otherwise, excessive unburned fuel may reach the catalytic converter causing it to overheat, which could start a fire.
Warning! As with any vehicle, do not idle, park or operate this vehicle in areas where combustible materials such as grass, hay or leaves can come into contact with the hot exhaust system, as these materials could be ignited and cause a vehicle fire.
J_C208_II.book Seite 179 Donnerstag, 31. Mai 2001 10:13 10
Emission control Certain systems of the engine serve to keep the toxic components of the exhaust gases within permissible limits required by law. These systems, of course, will function properly only when maintained strictly according to factory specifications. Any adjustments on the engine should, therefore, be carried out only by qualified Mercedes- Benz authorized center technicians. Engine adjustments should not be altered in any way. Moreover, the specified service jobs must be carried out regularly according to Mercedes-Benz servicing requirements. For details refer to the Service Booklet.
Warning! Inhalation of exhaust gas is hazardous to your health. All exhaust gas contains carbon monoxide, and inhaling it can cause unconsciousness and lead to death. Do not run the engine in confined areas (such as a garage) which are not properly ventilated. If you think that exhaust gas fumes are entering the vehicle while driving, have the cause determined and corrected immediately. If you must drive under these conditions, drive only with at least one window fully open.
Catalytic converter
179
Instruments and controls
Operation
Driving
Instrument cluster display
Practical hints
Car care
Technical
data
Index
J_C208_II.book Seite 180 Donnerstag, 31. Mai 2001 10:13 10
Instruments and controls
Tele Aid
Operation
Driving
Instrument cluster display
Practical hints
Car care
Technical
data
Index
180
Tele Aid (optional for Canada)
Important! The initial activation of the Tele Aid system may only be performed by completing the subscriber agreement and placing an acquaintance call using the “SOS” button. Failure to complete either of these steps will result in a system that is not activated. If the system is not activated the indicator lamp in the “SOS” button stays on after turning electronic key in starter switch to position 2 and the message “TELE AID – NOT ACTIVATED” will be shown in the multifunction display for approx. 10 seconds. If you have any questions regarding activation, please call the Response Center at 1-800-756-9018 (in the USA) or 1-888-923-8367 (in Canada).
(Telematic Alarm Identification on Demand) The Tele Aid system consists of three types of response; automatic and manual emergency, roadside assistance and information. The Tele Aid system is operational providing that the vehicle’s battery is charged, properly connected, not damaged and cellular and GPS coverage is available.
The speaker volume of a Tele Aid call can be adjusted when using the volume control on the multifunction steering wheel, for raising press button æ and for lowering press button ç. To activate, press the “SOS” button, the Roadside Assistance button (cid:127) or the Information button ¡, depending on the type of response required. Shortly after the completion of your Acquaintance Call, you will receive a user ID and password via first call mail. By visiting www.mbusa.com and selecting “Tele Aid” (USA only), you will have access to account information, remote door unlock, Info Services* profile and more.
* Optional – available only with COMAND
System self-check Initially, after turning the electronic key in starter switch to position 2, malfunctions are detected and indicated (the indicator lamps in the “SOS” button, the Roadside Assistance button (cid:127) and the Information button ¡ stay on longer than 10 seconds or do not come on). The message “TELE AID – VISIT WORKSHOP” appears for approx. 10 seconds in the multifunction display.
J_C208_II.book Seite 181 Donnerstag, 31. Mai 2001 10:13 10
Important! Always make sure that the indicator lamps in the “SOS” button, in the “Roadside Assistance” button and in the “Information” button do not remain illuminated constantly in red and the message “TELE AID - VISIT WORKSHOP” is not displayed in the multifunction display after the system self check. If a malfunction is indicated as outlined above, have the system checked at the nearest Mercedes-Benz Center as soon as possible.
Emergency calls An emergency call is initiated automatically: • following an accident in which the Emergency Tensioning Retractors (ETR’s) or airbags deploy,
• if the antitheft alarm or the tow away alarm stays on
for more than 20 seconds, see pages 43 and 44.
An emergency call can also be initiated manually by opening the cover next to the inside rear view mirror labeled “SOS”, then briefly pressing the button located under the cover. See below for instructions on initiating an emergency call manually.
Once the emergency call is in progress, the indicator lamp in the “SOS” button will begin to flash. The message “EMERGENCY CALL – CONNECTING CALL” appears in the multifunction display. When the connection is established, the message “EMERGENCY CALL – CALL CONNECTED” appears in the multifunction display. All information relevant to the emergency, such as the location of the vehicle (determined by the GPS satellite location system), vehicle model, identification number and color are generated. A voice connection between the Response Center and the occupants of the vehicle will be established automatically soon after the emergency call has been initiated. When a voice connection is established the audio system mutes and the message “TELE AID – EMERGENCY CALL ACTIVE” appears in the multifunction display. The Response Center will attempt to determine more precisely the nature of the accident provided they can speak to an occupant of the vehicle.
Tele Aid
Instruments and controls
Operation
Driving
Instrument cluster display
Practical hints
Car care
Technical
data
Index
181
J_C208_II.book Seite 182 Donnerstag, 31. Mai 2001 10:13 10
Instruments and controls
Tele Aid
Operation
Driving
Instrument cluster display
Practical hints
Car care
Technical
data
Index
The Tele Aid system is available if: • it has been activated and is operational. Activation requires a subscription for monitoring services and cellular air time,
• the relevant cellular phone network and GPS signals
are available and pass the information on to the response center.
Note: Location of the vehicle on a map is possible if the vehicle is able to receive signals from the GPS satellite network and pass the information on to the response center.
182
Warning! If the indicator lamp in the “SOS” button is illuminated continuously and there was no voice connection to the Response Center established, then the Tele Aid system could not initiate an emergency call (e.g. the relevant cellular phone network is not available). The message “EMERGENCY CALL – CALL FAILED” appears in the multifunction display for approx. 10 seconds. Should this occur, assistance must be summoned by other means.
J_C208_II.book Seite 183 Donnerstag, 31. Mai 2001 10:13 10
Initiating an emergency call manually
P82.95-0209-20
Briefly press on cover (1) – the cover will open.
Press the SOS button (2) briefly. The indicator lamp in the SOS button (2) will flash until the emergency call is concluded. Wait for a voice connection to the Response Center. Close the cover (1) after the emergency call is concluded.
Warning! If you feel at any way in jeopardy when in the vehicle (e.g. smoke or fire in the vehicle, vehicle in a dangerous road location), please do not wait for voice contact after you have pressed the emergency button. Carefully leave the vehicle and move to a safe location. The Response Center will automatically contact local emergency officials with the vehicle’s approximate location if they receive an automatic “SOS” signal and cannot make voice contact with the vehicle occupants.
Tele Aid
Instruments and controls
Operation
Driving
Instrument cluster display
Practical hints
Car care
Technical
data
Index
183
J_C208_II.book Seite 184 Donnerstag, 31. Mai 2001 10:13 10
Instruments and controls
Tele Aid
Operation
Driving
Instrument cluster display
Practical hints
Car care
Technical
data
Index
184
Roadside Assistance button (cid:127) Located below the center armrest cover is the Roadside Assistance button (cid:127). Pressing and holding the button (for longer than 2 seconds) will initiate a call to a Mercedes-Benz Roadside Assistance dispatcher. The button will flash while the call is in progress. The message “ROADSIDE ASSISTANCE – CONNECTING CALL” will appear in the multifunction display. When the connection is established, the message “ROADSIDE ASSISTANCE – CALL CONNECTED” appears in the multifunction display. The Tele Aid system will transmit data generating the vehicle identification number, model, color and location (subject to availability of cellular and GPS signals). A voice connection between the Roadside Assistance dispatcher and the occupants of the vehicle will be established. When a voice connection is established the audio system mutes and the message “TELE AID – ROADSIDE ASSISTANCE CALL ACTIVE” appears in the multifunction display. The nature of the need for assistance can then be described. The Mercedes-Benz Roadside assistance dispatcher will either dispatch a qualified Mercedes-Benz technician or arrange to tow your vehicle to the nearest Mercedes-Benz Center. For
services such as labor and/or towing charges may apply. Refer to the Roadside Assistance manual for more information.
These programs are only available in the USA: • Sign and Drive services: Services such as jump start, a few gallons of fuel or the replacement of a flat tire with the vehicle spare tire are obtainable,
• Remote Vehicle Diagnostics: This function permits the Mercedes-Benz Roadside Assistance dispatcher to download malfunction codes and actual vehicle data.
Notes: The indicator lamp in the Roadside Assistance button (cid:127) remains illuminated in red for approx. 10 seconds during the system self-check after turning electronic key in starter switch to position 2 (together with the “SOS” button and the Information button ¡). See system self-check on page 180 when the indicator lamp does not light up in red or stays on longer than approximately 10 seconds.
J_C208_II.book Seite 185 Donnerstag, 31. Mai 2001 10:13 10
If the indicator lamp in the Roadside Assistance button (cid:127) is illuminated continuously and there was no voice connection to the Response Center established, then the Tele Aid system could not initiate an Roadside Assistance call (e.g. the relevant cellular phone network is not available). The message “ROADSIDE ASSISTANCE – CALL FAILED” appears in the multifunction display. Roadside Assistance calls can be terminated using the ì button on the multifunction steering wheel.
Information button ¡ Located below the center armrest cover is the Information button ¡. Pressing and holding the button (for longer than 2 seconds) will initiate a call to the Customer Assistance Center. The button will flash while the call is in progress. The message “INFO – CONNECTING CALL” will appear in the multifunction display. When the connection is established, the message “INFO – CALL CONNECTED” appears in the multifunction display. The Tele Aid system will transmit data generating the vehicle identification number, model, color and location (subject to availability of cellular and GPS signals).
A voice connection between the Customer Assistance Center representative and the occupants of the vehicle will be established. When a voice connection is established the audio system mutes and the message “TELE AID – INFO CALL ACTIVE” appears in the multifunction display. Information regarding the operation of your vehicle, the nearest Mercedes-Benz Center or Mercedes-Benz USA products and services is available to you. For more details concerning Tele Aid, please visit www.mbusa.com and use your ID and password, sent to you separately, to learn more (USA only). Notes: The indicator lamp in the Information button ¡ remains illuminated in red for approx. 10 seconds during the system self-check after turning electronic key in starter switch to position 2 (together with the “SOS” button and the Roadside Assistance button (cid:127)). See system self-check on page 180 when the indicator lamp does not light up in red or stays on longer than approximately 10 seconds. If the indicator lamp in the Information button ¡ is illuminated continuously and there was no voice connection to the Response Center established, then the
Tele Aid
Instruments and controls
Operation
Driving
Instrument cluster display
Practical hints
Car care
Technical
data
Index
185
J_C208_II.book Seite 186 Donnerstag, 31. Mai 2001 10:13 10
Instruments and controls
Tele Aid
Operation
Driving
Instrument cluster display
Practical hints
