2010 Hyundai Tucson Owners Manual

For trailer towing guidelines information, refer to “Trailer towing”in section 5.

20

On AWD vehicles, your vehicle must be towed with a wheel lift and dollies or flatbed equipment with all the wheels off the ground.

CAUTION

The AWD vehicle should never be towed with the wheels on the ground. This can cause serious damage to the transaxle or the AWD system.

On 2WD vehicles, it is acceptable to tow the vehicle with the rear wheels on the ground (without dollies) and the front wheels off the ground. If any of the loaded wheels or suspen- sion components are damaged or the vehicle is being towed with the front wheels on the ground, use a towing dolly under the front wheels. When being towed by a commercial tow truck and wheel dollies are not used, the front of the vehicle should always be lift- ed, not the rear.

OUN046030

OUN046029

CAUTION

(cid:129) Do not tow the vehicle backwards with the front wheels on the ground as this may cause dam- age to the vehicle.

(cid:129) Do not tow with sling-type equip- ment. Use wheel lift or flatbed equipment.

When towing your vehicle in an emer- gency without wheel dollies : 1. Set the ignition switch in the ACC posi-

tion.

2. Place the transaxle shift lever in N

(Neutral).

3. Release the parking brake.

CAUTION

Failure to place the transaxle shift lever in N (Neutral) may cause inter- nal damage to the transaxle.

What to do in an emergency

■ Front

■ Rear

OLM069016L

OLM069014

Removable towing hook (rear) 1. Open the tailgate, and remove the tow-

ing hook from the tool case.

2. Remove the hole cover pressing the lower part of the cover on the rear bumper.

3. Install the towing hook by turning it clockwise into the hole until it is fully secured.

4. Remove the towing hook and install

the cover after use.

OLM069015

Emergency towing If towing is necessary, we recommend you to have it done by an authorized HYUNDAI dealer or a commercial tow truck service.

6 21

What to do in an emergency

If towing service is not available in an emergency, your vehicle may be tem- porarily towed using a cable or chain secured to the emergency towing hook under the front (or rear) of the vehicle. Use extreme caution when towing the vehicle. A driver must be in the vehicle to steer it and operate the brakes. Towing in this manner may be done only on hard-surfaced roads for a short dis- tance and at low speeds. Also, the wheels, axles, power train, steering and brakes must all be in good condition. (cid:129) Do not use the tow hooks to pull a vehi- cle out of mud, sand or other condi- tions from which the vehicle cannot be driven out under its own power.

(cid:129) Avoid towing a vehicle heavier than the

vehicle doing the towing.

(cid:129) The drivers of both vehicles should communicate with each other frequent- ly.

CAUTION

(cid:129) Attach a towing strap to the tow

hook.

(cid:129) Using a portion of the vehicle other than the tow hooks for tow- ing may damage the body of your vehicle.

(cid:129) Use only a cable or chain specifi- cally intended for use in towing vehicles. Securely fasten the cable or chain to the towing hook provided.

(cid:129) Before emergency towing, check that

the hook is not broken or damaged.

(cid:129) Fasten the towing cable or chain

securely to the hook.

(cid:129) Do not jerk the hook. Apply steady and

even force.

(cid:129) To avoid damaging the hook, do not pull from the side or at a vertical angle. Always pull straight ahead.

WARNING

Use extreme caution when towing the vehicle. (cid:129) Avoid sudden starts or erratic driving maneuvers which would place excessive stress on the emergency towing hook and tow- ing cable or chain. The hook and towing cable or chain may break and cause serious injury or dam- age.

(cid:129) If the disabled vehicle is cannot be moved, do not forcibly contin- ue the towing. Contact an author- ized HYUNDAI dealer or a com- mercial tow truck service for assistance.

(cid:129) Tow the vehicle as straight ahead

as possible.

(cid:129) Keep away from the vehicle dur-

ing towing.

22

Emergency towing precautions (cid:129) Turn the ignition switch to ACC so the

steering wheel isn’t locked.

(cid:129) Place the transaxle shift lever in N

(Neutral).

(cid:129) Release the parking bake. (cid:129) Press the brake pedal with more force than normal since you will have reduced brake performance.

(cid:129) More steering effort will be required because the power steering system will be disabled.

(cid:129) If you are driving down a long hill, the brakes may overheat and brake per- formance will be reduced. Stop often and let the brakes cool off.

OEN066014
(cid:129) Use a towing strap less than 16 feet (5
m) long. Attach a white or red cloth (about 12 inches (30 cm) wide) in the middle of the strap for easy visibility.

(cid:129) Drive carefully so that the towing strap

is not loosened during towing.

What to do in an emergency

CAUTION - Automatic transaxle

(cid:129) If the car is being towed with all four wheels on the ground,it can be towed only from the front.Be sure that the transaxle is in neu- tral. Be sure the steering is unlocked by placing the ignition switch in the ACC position. A driver must be in the towed vehi- cle to operate the steering and brakes.

(cid:129) To avoid serious damage to the automatic transaxle, limit the vehicle speed to 15 km/h (10 mph) and drive less than 1.5 km (1
mile) when towing.

(cid:129) Before towing, check the auto- matic transaxle fluid leak under your vehicle. If the automatic transaxle fluid is leaking, a flatbed equipment or towing dolly must be used.

6 23

What to do in an emergency

Tie-down hook (for flatbed towing) (if equipped)

OLM069017N

WARNING

(cid:129) Do not use the hooks under the front (or rear) of the vehicle for towing purposes. These hooks are designed ONLY for transport tie-down. If the tie-down hooks are used for towing, the tie-down hooks or front (or rear) bumper will be damaged and this could lead to serious injury.

(cid:129) The hooks should be placed toward the front of the vehicle when using the front holes and should be placed toward the rear of the vehicle when using the rear holes for tie down purpose. If not, the front or rear under cover will be damaged.

24

Engine compartment / 7-2
Maintenance services / 7-3
Owner maintenance / 7-4
Scheduled maintenance service / 7-6
Explanation of scheduled maintenance items / 7-18
Engine oil / 7-21
Engine coolant / 7-22
Brake/clutch fluid / 7-25
Washer fluid / 7-26
Parking brake / 7-27
Air cleaner / 7-28
Climate control air filter / 7-29
Wiper blades / 7-31
Battery / 7-34
Tires and wheels / 7-37
Fuses / 7-50
Light bulbs / 7-59

Maintenance

Appearance care / 7-66
Emission control system / 7-72
California perchlorate notice / 7-75

Maintenance

ENGINE COMPARTMENT

1. Engine coolant reservoir 2. Engine oil filler cap 3. Brake/Clutch* fluid reservoir 4. Air cleaner 5. Fuse box 6. Negative battery terminal 7. Positive battery terminal 8. Radiator cap 9. Engine oil dipstick 10. Windshield washer fluid reservoir * : if equipped

* The actual engine room in the vehicle may differ from the illustration.

OLM079001

27

MAINTENANCE SERVICES You should exercise the utmost care to prevent damage to your vehicle and injury to yourself whenever performing any maintenance or inspection proce- dures. Should you have any doubts concerning the inspection or servicing of your vehi- cle, we strongly recommend that you have an authorized HYUNDAI dealer perform this work. An authorized HYUNDAI dealer has fac- tory-trained technicians and genuine HYUNDAI parts to service your vehicle properly. For expert advice and quality service, see an authorized HYUNDAI dealer. Inadequate, incomplete or insufficient servicing may result in operational prob- lems with your vehicle that could lead to vehicle damage, an accident, or person- al injury.

Owner’s responsibility

✽✽ NOTICE Maintenance Service and Record Retention are the owner's responsibility.

You should retain documents that show proper maintenance has been performed on your vehicle in accordance with the scheduled maintenance service charts shown on the following pages. You need this information to establish your compli- ance with the servicing and maintenance requirements of your vehicle warranties. Detailed warranty information is provided in your Owner’s Handbook & Warranty Information booklet. Repairs and adjustments required as a result of improper maintenance or a lack of required maintenance are not covered. We recommend you have your vehicle maintained and repaired by an author- ized HYUNDAI dealer. An authorized HYUNDAI dealer meets HYUNDAI’s high service quality standards and receives technical support from HYUNDAI in order to provide you with a high level of service satisfaction.

Maintenance

Owner maintenance precautions Improper or incomplete service may result in problems. This section gives instructions only for the maintenance items that are easy to perform. As explained earlier in this section, sev- eral procedures can be done only by an authorized HYUNDAI dealer with special tools.

✽✽ NOTICE Improper owner maintenance during the warranty period may affect warranty coverage. For details, read the separate Owner’s Handbook & Warranty Information booklet provided with the vehicle. If you're unsure about any serv- icing or maintenance procedure, have it done by an authorized HYUNDAI dealer.

7 3

OWNER MAINTENANCE The following lists are vehicle checks and inspections that should be performed by the owner or an authorized HYUNDAI dealer at the frequencies indicated to help ensure safe, dependable operation of your vehicle. Any adverse conditions should be brought to the attention of your dealer as soon as possible. These Owner Maintenance Checks are generally not covered by warranties and you may be charged for labor, parts and lubricants used.

Owner maintenance schedule When you stop for fuel: (cid:129) Check the engine oil level. (cid:129) Check the coolant level in coolant

reservoir.

(cid:129) Check the windshield washer fluid

level.

(cid:129) Look for low or under-inflated tires.

WARNING

Be careful when checking your engine coolant level when the engine is hot. Scalding hot coolant and steam may blow out under pressure. This could cause burns or other serious injury.

Maintenance

WARNING - Maintenance

work

(cid:129) Performing maintenance work on a vehicle can be dangerous. You can be seriously injured while performing some maintenance procedures. If you lack sufficient knowledge and experience or the proper tools and equipment to do the work, have it done by an authorized HYUNDAI dealer.

(cid:129) Working under the hood with the engine running is dangerous. It becomes even more dangerous when you wear jewelry or loose clothing. These can become entangled in moving parts and result in injury. Therefore, if you must run the engine while work- ing under the hood, make certain that you remove all jewelry (espe- cially rings, bracelets, watches, and necklaces) and all neckties, scarves, and similar loose cloth- ing before getting near the engine or cooling fans.

47

While operating your vehicle: (cid:129) Note any changes in the sound of the exhaust or any smell of exhaust fumes in the vehicle.

(cid:129) Check for vibrations in the steering wheel. Notice any increased steering effort or looseness in the steering wheel, or change in its straight-ahead position.

(cid:129) Notice if your vehicle constantly turns slightly or “pulls” to one side when trav- eling on smooth, level road.

(cid:129) When stopping, listen and check for unusual sounds, pulling to one side, increased brake pedal travel or “hard- to-push” brake pedal.

(cid:129) If any slipping or changes in the oper- ation of your transaxle occurs, check the transaxle fluid level.

(cid:129) Check the automatic transaxle P

(Park) function.

(cid:129) Check the parking brake. (cid:129) Check for fluid leaks under your vehicle (water dripping from the air condition- ing system during or after use is nor- mal).

At least monthly: (cid:129) Check the coolant level in the engine

coolant reservoir.

(cid:129) Check the operation of all exterior lights, including the stoplights, turn sig- nals and hazard warning flashers.

(cid:129) Check the inflation pressures of all

tires including the spare.

At least twice a year (i.e.,every Spring and Fall): (cid:129) Check the radiator, heater and air con-

ditioning hoses for leaks or damage.

(cid:129) Check the windshield washer spray and wiper operation. Clean the wiper blades with clean cloth dampened with washer fluid.

(cid:129) Check the headlight alignment. (cid:129) Check the muffler, exhaust pipes,

shields and clamps.

(cid:129) Check the lap/shoulder belts for wear

and function.

(cid:129) Check for worn tires and loose wheel

lug nuts.

Maintenance

At least once a year: (cid:129) Clean the body and door drain holes. (cid:129) Lubricate the door hinges and checks,

and hood hinges.

(cid:129) Lubricate the door and hood locks and

latches.

(cid:129) Lubricate the door rubber weather-

strips.

(cid:129) Check the air conditioning system. (cid:129) Inspect and lubricate the automatic

transaxle linkage and controls.

(cid:129) Clean the battery and terminals. (cid:129) Check the brake/clutch* fluid level. * : if equipped

7 5

Maintenance

SCHEDULED MAINTENANCE SERVICE Follow Normal Maintenance Schedule if the vehicle is usually operated where none of the following conditions apply. If any of the following conditions apply, fol- low Maintenance Under Severe Usage Conditions. (cid:129) Repeated short distance driving. (cid:129) Driving in dusty conditions or sandy

If your vehicle is operated under the above conditions, you should inspect, replace or refill more frequently than the following Normal Maintenance Schedule. After 120 months or 150,000 miles (240,000 km) continue to follow the pre- scribed maintenance intervals.

areas.

(cid:129) Extensive use of brakes. (cid:129) Driving in areas where salt or other

corrosive materials are being used.

(cid:129) Driving on rough or muddy roads. (cid:129) Driving in mountainous areas. (cid:129) Extended periods of idling or low

speed operation.

(cid:129) Driving for a prolonged period in cold temperatures and/or extremely humid climates.

(cid:129) More than 50% driving in heavy city traffic during hot weather above 90°F (32°C).

67

Maintenance

NORMAL MAINTENANCE SCHEDULE The following maintenance services must be performed to ensure good emission control and performance. Keep receipts for all vehicle emission services to protect your warranty. Where both mileage and time are shown, the frequency of service is deter- mined by whichever occurs first.

7,500 miles (12,000 km) or 6 months

22,500 miles (36,000 km) or 18 months

❑ Inspect air cleaner filter ❑ Inspect vacuum hose ❑ Replace engine oil and filter

❑ Inspect air cleaner filter ❑ Inspect vacuum hose ❑ Replace engine oil and filter

(7,500 miles (12,000 km) or 12 months)

(22,500 miles (36,000 km) or 36 months)

15,000 miles (24,000 km) or 12 months

❑ Inspect air cleaner filter ❑ Inspect vacuum hose ❑ Inspect air conditioning refrigerant ❑ Inspect brake hoses and lines ❑ Inspect drive shafts and boots ❑ Inspect electronic throttle control ❑ Inspect exhaust pipe and muffler ❑ Inspect front disc brake/pads, calipers and rotors ❑ Inspect propeller shaft (AWD) ❑ Inspect steering gear box, linkage & boots/lower arm ball joint,

upper arm ball joint

❑ Inspect suspension mounting bolts ❑ Replace climate control air filter (for evaporator and blower unit) ❑ Replace engine oil and filter

(15,000 miles (24,000 km) or 24 months)

7 7

Maintenance

NORMAL MAINTENANCE SCHEDULE (CONT.)

30,000 miles (48,000 km) or 24 months

37,500 miles (60,000 km) or 30 months

❑ Inspect air cleaner filter ❑ Inspect vacuum hose ❑ Inspect manual transaxle fluid (if equipped) ❑ Inspect rear axle oil (AWD) *2
❑ Inspect transfer case oil (AWD) *2
❑ Replace engine oil and filter

(37,500 miles (60,000 km) or 60 months)

*1 : Fuel filter & Fuel tank air filter are considered to be maintenance free but peri- odic inspection is recommended for this maintenance schedule depends on fuel quality. If there are some important safety matters like fuel flow restric- tion, surging, loss of power, hard starting problem etc, replace the fuel filter immediately regardless of maintenance schedule and consult an authorized HYUNDAI dealer for details.

*2 : Transfer case oil and rear axle oil should be changed anytime they have been

submerged in water.

❑ Inspect vacuum hose ❑ Inspect air conditioning refrigerant ❑ Inspect brake hoses and lines ❑ Inspect drive shafts and boots ❑ Inspect electronic throttle control ❑ Inspect exhaust pipe and muffler ❑ Inspect front disc brake/pads, calipers and rotors ❑ Inspect propeller shaft (AWD) ❑ Inspect steering gear box, linkage & boots/lower arm ball joint,

upper arm ball joint

❑ Inspect suspension mounting bolts ❑ Inspect brake/clutch (if equipped) fluid ❑ Inspect crankcase ventilation hose ❑ Inspect fuel filter *1
❑ Inspect fuel lines, fuel hoses and connections ❑ Inspect fuel tank air filter (if equipped) *1
❑ Inspect rear disc brake/pads, parking brake ❑ Inspect vapor hose and fuel filler cap, fuel tank ❑ Replace climate control air filter (for evaporator and blower unit) ❑ Replace air cleaner filter ❑ Replace engine oil and filter

(30,000 miles (48,000 km) or 48 months)

87

NORMAL MAINTENANCE SCHEDULE (CONT.)

45,000 miles (72,000 km) or 36 months

52,500 miles (84,000 km) or 42 months

Maintenance

❑ Inspect air cleaner filter ❑ Inspect vacuum hose ❑ Replace engine oil and filter

(52,500 miles (84,000 km) or 84 months)

❑ Inspect air cleaner filter ❑ Inspect vacuum hose ❑ Inspect air conditioning refrigerant ❑ Inspect brake hoses and lines ❑ Inspect drive shafts and boots ❑ Inspect electronic throttle control ❑ Inspect exhaust pipe and muffler ❑ Inspect front disc brake/pads, calipers and rotors ❑ Inspect propeller shaft (AWD) ❑ Inspect steering gear box, linkage & boots/lower arm ball joint,

upper arm ball joint

❑ Inspect suspension mounting bolts ❑ Replace climate control air filter (for evaporator and blower unit) ❑ Replace engine oil and filter

(45,000 miles (72,000 km) or 72 months)

7 9

Maintenance

NORMAL MAINTENANCE SCHEDULE (CONT.)

60,000 miles (96,000 km) or 48 months

67,500 miles (108,000 km) or 54 months

❑ Inspect air cleaner filter ❑ Inspect vacuum hose ❑ Replace engine oil and filter

(67,500 miles (108,000 km) or 108 months)

*1 : Fuel filter & Fuel tank air filter are considered to be maintenance free but periodic inspection is recommended for this maintenance schedule depends on fuel quality. If there are some important safety matters like fuel flow restriction, surging, loss of power, hard starting problem etc, replace the fuel filter immediately regardless of maintenance schedule and consult an authorized HYUNDAI dealer for details.

*3 : Inspect for excessive tappet noise and/or engine vibration and adjust if nec-

essary.

❑ Inspect vacuum hose ❑ Inspect air conditioning refrigerant ❑ Inspect brake hoses and lines ❑ Inspect drive shafts and boots ❑ Inspect electronic throttle control ❑ Inspect exhaust pipe and muffler ❑ Inspect front disc brake/pads, calipers and rotors ❑ Inspect propeller shaft (AWD) ❑ Inspect steering gear box, linkage & boots/lower arm ball joint,

upper arm ball joint

❑ Inspect suspension mounting bolts ❑ Inspect brake/clutch (if equipped) fluid ❑ Inspect crankcase ventilation hose ❑ Inspect fuel filter *1
❑ Inspect fuel lines, fuel hoses and connections ❑ Inspect fuel tank air filter (if equipped) *1
❑ Inspect rear disc brake/pads, parking brake ❑ Inspect vapor hose and fuel filler cap, fuel tank ❑ Inspect valve clearance *3
❑ Inspect drive belt (auto-tensioner, generator, p/str'g, a/con, w/pump)

(First, 60,000 miles (96,000 km) or 48 months after every 15,000 miles (24,000 km) or 12 months)

❑ Replace climate control air filter (for evaporator and blower unit) ❑ Replace air cleaner filter ❑ Replace engine oil and filter

(60,000 miles (96,000 km) or 96 months)

10

NORMAL MAINTENANCE SCHEDULE (CONT.)

75,000 miles (120,000 km) or 60 months

82,500 miles (132,000 km) or 66 months

Maintenance

❑ Inspect air cleaner filter ❑ Inspect vacuum hose ❑ Replace engine oil and filter

(82,500 miles (132,000 km) or 132 months)

❑ Inspect air cleaner filter ❑ Inspect vacuum hose ❑ Inspect air conditioning refrigerant ❑ Inspect brake hoses and lines ❑ Inspect drive shafts and boots ❑ Inspect electronic throttle control ❑ Inspect exhaust pipe and muffler ❑ Inspect front disc brake/pads, calipers and rotors ❑ Inspect propeller shaft (AWD) ❑ Inspect steering gear box, linkage & boots/lower arm ball joint,

upper arm ball joint

❑ Inspect suspension mounting bolts ❑ Inspect manual transaxle fluid (if equipped) ❑ Inspect rear axle oil (AWD) *2
❑ Inspect transfer case oil (AWD) *2
❑ Inspect drive belt (auto-tensioner, generator, p/str'g, a/con, w/pump)

(First, 60,000 miles (96,000 km) or 48 months after every 15,000 miles (24,000 km) or 12 months)

❑ Replace climate control air filter (for evaporator and blower unit) ❑ Replace engine oil and filter

(75,000 miles (120,000 km) or 120 months)

*2 : Transfer case oil and rear axle oil should be changed anytime they have been

submerged in water.

7 11

Maintenance

NORMAL MAINTENANCE SCHEDULE (CONT.)

90,000 miles (144,000 km) or 72 months

97,500 miles (156,000 km) or 78 months

❑ Inspect air cleaner filter ❑ Inspect vacuum hose ❑ Replace engine oil and filter

(97,500 miles (156,000 km) or 156 months)

*1 : Fuel filter & Fuel tank air filter are considered to be maintenance free but periodic inspection is recommended for this maintenance schedule depends on fuel quality. If there are some important safety matters like fuel flow restriction, surging, loss of power, hard starting problem etc, replace the fuel filter immediately regardless of maintenance schedule and consult an author- ized HYUNDAI dealer for details.

❑ Inspect vacuum hose ❑ Inspect air conditioning refrigerant ❑ Inspect brake hoses and lines ❑ Inspect drive shafts and boots ❑ Inspect electronic throttle control ❑ Inspect exhaust pipe and muffler ❑ Inspect front disc brake/pads, calipers and rotors ❑ Inspect propeller shaft (AWD) ❑ Inspect steering gear box, linkage & boots/lower arm ball joint,

upper arm ball joint

❑ Inspect suspension mounting bolts ❑ Inspect brake/clutch (if equipped) fluid ❑ Inspect crankcase ventilation hose ❑ Inspect fuel filter *1
❑ Inspect fuel lines, fuel hoses and connections ❑ Inspect fuel tank air filter (if equipped) *1
❑ Inspect rear disc brake/pads, parking brake ❑ Inspect vapor hose and fuel filler cap, fuel tank ❑ Inspect drive belt (auto-tensioner, generator, p/str'g, a/con, w/pump)

(First, 60,000 miles (96,000 km) or 48 months after every 15,000 miles (24,000 km) or 12 months)

❑ Replace climate control air filter (for evaporator and blower unit) ❑ Replace air cleaner filter ❑ Replace engine oil and filter

(90,000 miles (144,000 km) or 144 months)

12

NORMAL MAINTENANCE SCHEDULE (CONT.)

105,000 miles (168,000 km) or 84 months

112,500 miles (180,000 km) or 90 months

Maintenance

❑ Inspect air cleaner filter ❑ Inspect vacuum hose ❑ Inspect manual transaxle fluid (if equipped) ❑ Inspect rear axle oil (AWD) *2
❑ Inspect transfer case oil (AWD) *2
❑ Replace engine oil and filter

(112,500 miles (180,000 km) or 180 months)

*2 : Transfer case oil and rear axle oil should be changed anytime they have been

submerged in water.

❑ Inspect air cleaner filter ❑ Inspect vacuum hose ❑ Inspect air conditioning refrigerant ❑ Inspect brake hoses and lines ❑ Inspect drive shafts and boots ❑ Inspect electronic throttle control ❑ Inspect exhaust pipe and muffler ❑ Inspect front disc brake/pads, calipers and rotors ❑ Inspect propeller shaft (AWD) ❑ Inspect steering gear box, linkage & boots/lower arm ball joint,

upper arm ball joint

❑ Inspect suspension mounting bolts ❑ Inspect drive belt (auto-tensioner, generator, p/str'g, a/con, w/pump)

(First, 60,000 miles (96,000 km) or 48 months after every 15,000 miles (24,000 km) or 12 months)

❑ Replace climate control air filter (for evaporator and blower unit) ❑ Replace spark plugs (iridium coated) ❑ Replace engine oil and filter

(105,000 miles (168,000 km) or 168 months)

7 13

Maintenance

NORMAL MAINTENANCE SCHEDULE (CONT.)

120,000 miles (192,000 km) or 96 months

127,500 miles (204,000 km) or 102 months

❑ Inspect air cleaner filter ❑ Inspect vacuum hose ❑ Replace engine oil and filter

(127,500 miles (204,000 km) or 204 months)

*1 : Fuel filter & Fuel tank air filter are considered to be maintenance free but periodic inspection is recommended for this maintenance schedule depends on fuel quality. If there are some important safety matters like fuel flow restriction, surging, loss of power, hard starting problem etc, replace the fuel filter immediately regardless of maintenance schedule and consult an authorized HYUNDAI dealer for details.

*3 : Inspect for excessive tappet noise and/or engine vibration and adjust if nec-

essary.

❑ Inspect vacuum hose ❑ Inspect air conditioning refrigerant ❑ Inspect brake hoses and lines ❑ Inspect drive shafts and boots ❑ Inspect electronic throttle control ❑ Inspect exhaust pipe and muffler ❑ Inspect front disc brake/pads, calipers and rotors ❑ Inspect propeller shaft (AWD) ❑ Inspect steering gear box, linkage & boots/lower arm ball joint,

upper arm ball joint

❑ Inspect suspension mounting bolts ❑ Inspect brake/clutch (if equipped) fluid ❑ Inspect crankcase ventilation hose ❑ Inspect fuel filter *1
❑ Inspect fuel lines, fuel hoses and connections ❑ Inspect fuel tank air filter (if equipped) *1
❑ Inspect rear disc brake/pads, parking brake ❑ Inspect vapor hose and fuel filler cap, fuel tank ❑ Inspect valve clearance *3
❑ Inspect drive belt (auto-tensioner, generator, p/str'g, a/con, w/pump)

(First, 60,000 miles (96,000 km) or 48 months after every 15,000 miles (24,000 km) or 12 months)

❑ Replace climate control air filter (for evaporator and blower unit) ❑ Replace air cleaner filter ❑ Replace engine oil and filter

(120,000 miles (192,000 km) or 192 months)

❑ Replace coolant (First, 120,000 miles (192,000 km) or 120 months

after every 30,000 miles (48,000 km) or 24 months)

14

NORMAL MAINTENANCE SCHEDULE (CONT.)

135,000 miles (216,000 km) or 108 months

142,500 miles (228,000 km) or 114 months

Maintenance

❑ Inspect air cleaner filter ❑ Inspect vacuum hose ❑ Replace engine oil and filter

(142,500 miles (228,000 km) or 228 months)

❑ Inspect air cleaner filter ❑ Inspect vacuum hose ❑ Inspect air conditioning refrigerant ❑ Inspect brake hoses and lines ❑ Inspect drive shafts and boots ❑ Inspect electronic throttle control ❑ Inspect exhaust pipe and muffler ❑ Inspect front disc brake/pads, calipers and rotors ❑ Inspect propeller shaft (AWD) ❑ Inspect steering gear box, linkage & boots/lower arm ball joint,

upper arm ball joint

❑ Inspect suspension mounting bolts ❑ Inspect drive belt (auto-tensioner, generator, p/str'g, a/con, w/pump)

(First, 60,000 miles (96,000 km) or 48 months after every 15,000 miles (24,000 km) or 12 months)

❑ Replace climate control air filter (for evaporator and blower unit) ❑ Replace engine oil and filter

(135,000 miles (216,000 km) or 216 months)

7 15

Maintenance

NORMAL MAINTENANCE SCHEDULE (CONT.)

150,000 miles (240,000 km) or 120 months

❑ Inspect vacuum hose ❑ Inspect air conditioning refrigerant ❑ Inspect brake hoses and lines ❑ Inspect drive shafts and boots ❑ Inspect electronic throttle control ❑ Inspect exhaust pipe and muffler ❑ Inspect front disc brake/pads, calipers and rotors ❑ Inspect propeller shaft (AWD) ❑ Inspect steering gear box, linkage & boots/lower arm ball joint,

upper arm ball joint

❑ Inspect suspension mounting bolts ❑ Inspect brake/clutch (if equipped) fluid ❑ Inspect crankcase ventilation hose ❑ Inspect fuel filter *1
❑ Inspect fuel lines, fuel hoses and connections ❑ Inspect fuel tank air filter (if equipped) *1
❑ Inspect rear disc brake/pads, parking brake ❑ Inspect vapor hose and fuel filler cap, fuel tank ❑ Inspect manual transaxle fluid (if equipped) ❑ Inspect rear axle oil (AWD) *2
❑ Inspect transfer case oil (AWD) *2
❑ Inspect drive belt (auto-tensioner, generator, p/str'g, a/con, w/pump)

(First, 60,000 miles (96,000 km) or 48 months after every 15,000 miles (24,000 km) or 12 months)

(Continued)

16

(Continued) ❑ Replace climate control air filter (for evaporator and blower unit) ❑ Replace air cleaner filter ❑ Replace engine oil and filter

(150,000 miles (240,000 km) or 240 months)

❑ Replace coolant (First, 120,000 miles (192,000 km) or 120 months

after every 30,000 miles (48,000 km) or 24 months)

No check, No service required

❑ Automatic transaxle fluid (if equipped)

*1 : Fuel filter & Fuel tank air filter are considered to be maintenance free but periodic inspection is recommended for this maintenance schedule depends on fuel quality. If there are some important safety matters like fuel flow restriction, surging, loss of power, hard starting problem etc, replace the fuel filter immediately regardless of maintenance schedule and consult an authorized HYUNDAI dealer for details.

*2 : Transfer case oil and rear axle oil should be changed anytime they have been

submerged in water.

Maintenance

MAINTENANCE UNDER SEVERE USAGE CONDITIONS The following items must be serviced more frequently on cars normally used under severe driving conditions. Refer to the chart below for the appropriate maintenance intervals. R : Replace I : Inspect and, after inspection, clean, adjust, repair or replace if necessary

MAINTENANCE ITEM

MAINTENANCE

OPERATION

MAINTENANCE INTERVALS

DRIVING CONDITION

ENGINE OIL AND FILTER

AIR CLEANER FILTER

SPARK PLUGS

AUTOMATIC TRANSAXLE FLUID

MANUAL TRANSAXLE FLUID

FRONT DISC BRAKE/PADS, CALIPERS AND ROTORS

REAR DISC BRAKE/PADS, PARKING BRAKE

STEERING GEAR BOX, LINKAGE & BOOTS/ LOWER ARM BALL JOINT, UPPER ARM BALL JOINT

DRIVE SHAFTS AND BOOTS

TRANSFER CASE OIL (AWD)

REAR AXLE OIL (AWD)

CLIMATE CONTROL AIR FILTER (FOR EVAPORATOR AND BLOWER UNIT)

PROPELLER SHAFT

EVERY 3,750 MILES (6,000 KM) OR 6 MONTHS

A, B, C, D, E, F, G, H, I, K

MORE FREQUENTLY

MORE FREQUENTLY

EVERY 60,000 MILES (96,000 KM)

EVERY 75,000 MILES (120,000 KM)

MORE FREQUENTLY

MORE FREQUENTLY

MORE FREQUENTLY

C, E

B, H

A, C, E, F, G, I

A, C, E, F, G, I

C, D, G, H

C, D, G, H

C, D, E, F, G, H, I

EVERY 7,500 MILES (12,000 KM) OR 6 MONTHS

C, D, E, F, G, H, I, J

EVERY 75,000 MILES (120,000 KM)

EVERY 75,000 MILES (120,000 KM)

C, D, E, G, H, I, J

C, D, E, G, H, I, J

MORE FREQUENTLY

EVERY 7,500 MILES (12,000 KM) OR 6 MONTHS

C, E

C, E

SEVERE DRIVING CONDITIONS A - Repeatedly driving short distance of less than 5 miles (8 km) in normal tem-

perature or less than 10 miles (16 km) in freezing temperature B - Extensive engine idling or low speed driving for long distances C - Driving on rough, dusty, muddy, unpaved, graveled or salt- spread roads D - Driving in areas using salt or other corrosive materials or in very cold weather E - Driving in sandy areas

F - Driving in heavy traffic area over 90°F (32°C) G - Driving on uphill, downhill, or mountain road H - Towing a Trailer, or using a camper, or roof rack J - Driving over 106 mph (170 km/h) K - Frequently driving in stop-and-go conditions

- Driving as a patrol car, taxi, other commercial use or vehicle towing

7 17

Fuel lines, fuel hoses and con- nections Check the fuel lines, fuel hoses and con- nections for leakage and damage. Have an authorized HYUNDAI dealer replace any damaged or leaking parts immedi- ately.

Vapor hose and fuel filler cap The vapor hose and fuel filler cap should be inspected at those intervals specified in the maintenance schedule. Make sure that a new vapor hose or fuel filler cap is correctly replaced.

Maintenance

EXPLANATION OF SCHEDULED MAINTENANCE ITEMS Engine oil and filter The engine oil and filter should be changed at the intervals specified in the maintenance schedule. If the vehicle is being driven in severe conditions, more frequent oil and filter changes are required.

Fuel filter (cartridge) A clogged filter can limit the speed at which the vehicle may be driven, damage the emission system and cause multiple issues such as hard starting. If an exces- sive amount of foreign matter accumu- lates in the fuel tank, the filter may require replacement more frequently. After installing a new filter, run the engine for several minutes, and check for leaks at the connections. Fuel filters should be installed by an authorized HYUNDAI dealer.

Drive belts Inspect all drive belts for evidence of cuts, cracks, excessive wear or oil satu- ration and replace if necessary. Drive belts should be checked periodically for proper tension and adjusted as neces- sary.

18

Vacuum crankcase ventilation hoses Inspect the surface of hoses for evidence of heat and/or mechanical damage. Hard and brittle rubber, cracking, tears, cuts, abrasions, and excessive swelling indi- cate deterioration. Particular attention should be paid to examine those hose surfaces nearest to high heat sources, such as the exhaust manifold. Inspect the hose routing to assure that the hoses do not come in contact with any heat source, sharp edges or moving component which might cause heat dam- age or mechanical wear. Inspect all hose connections, such as clamps and cou- plings, to make sure they are secure, and that no leaks are present. Hoses should be replaced immediately if there is any evidence of deterioration or damage.

Air cleaner filter A Genuine HYUNDAI air cleaner filter is recommended when is replaced.

filter

the

Spark plugs Make sure to install new spark plugs of the correct heat range.

Valve clearance Inspect for excessive valve noise and/or engine vibration and adjust if necessary. An authorized HYUNDAI dealer should perform the operation.

Cooling system Check for cooling system components, such as radiator, coolant reservoir, hoses and connections for leakage and dam- age. Replace any damaged parts.

Maintenance

Coolant The coolant should be changed at the intervals specified in the maintenance schedule.

Manual transaxle fluid (if equipped) Inspect fluid according to the maintenance schedule.

the manual

transaxle

Automatic transaxle fluid (if equipped) Automatic transaxle fluid should not be checked under normal usage conditions. But in severe conditions, the fluid should be changed at an authorized HYUNDAI dealer in accordance to the scheduled maintenance at the beginning of this chapter.

✽✽ NOTICE Automatic transaxle fluid color is basi- cally red. As the vehicle is driven, the automatic transaxle fluid will begin to look darker. It is normal condition and you should not judge the need to replace the fluid based upon the changed color.

7 19

Parking brake Inspect the parking brake system includ- ing the parking brake pedal and cables.

Brake discs, pads, calipers and rotors Check the pads for excessive wear, discs for run out and wear, and calipers for fluid leakage.

Exhaust pipe and muffler Visually inspect the exhaust pipes, muf- fler and hangers for cracks, deterioration, or damage. Start the engine and listen carefully for any exhaust gas leakage. Tighten connections or replace parts as necessary.

Suspension mounting bolts Check the suspension connections for looseness or damage. Retighten to the specified torque.

Steering gear box, linkage & boots/lower arm ball joint With the vehicle stopped and engine off, check for excessive free-play in the steering wheel. Check the linkage for bends or damage. Check the dust boots and ball joints for deterioration, cracks, or damage. Replace any damaged parts.

Drive shafts and boots Check the drive shafts, boots and clamps for cracks, deterioration, or damage. Replace any damaged parts and, if nec- essary, repack the grease.

Air conditioning refrigerant Check the air conditioning lines and con- nections for leakage and damage.

Maintenance

CAUTION

The use of a non-specified fluid could result in transaxle malfunc- tion and failure. Use only specified automatic transaxle to “Recommended lubricants and capacities”in section 8.)

(Refer

fluid.

Brake hoses and lines Visually check for proper installation, chafing, cracks, deterioration and any leakage. Replace any deteriorated or damaged parts immediately.

Brake/Clutch* fluid Check the brake fluid level in the brake fluid reservoir. The level should be between “MIN” and “MAX” marks on the side of the reservoir. Use only hydraulic brake fluid conforming to DOT 3 or DOT 4 specification. * : if equipped

20

ENGINE OIL

Maintenance

3. Turn the engine off and wait for a few minutes (about 5 minutes) for the oil to return to the oil pan.

4. Pull the dipstick out, wipe it clean, and

re-insert it fully.

WARNING - Radiator hose Be very careful not to touch the radiator hose when checking or adding the engine oil as it may be hot enough to burn you.

5. Pull the dipstick out again and check the level. The level should be between F and L.

CAUTION

Do not overfill with engine oil. Engine damage may result.

OLM079003N

Checking the engine oil level 1. Be sure the vehicle is on level ground. 2. Start the engine and allow it to reach

normal operating temperature.

OLM079004N If it is near or at L, add enough oil to bring the level to F. Do not overfill.

Use a funnel to help prevent oil from being spilled on engine components.

Use only the specified engine oil.(Refer to “Recommended lubricants and capaci- ties”in section 8.)

7 21

Maintenance

Changing the engine oil and filter Have engine oil and filter changed by an authorized HYUNDAI dealer according to the Maintenance Schedule at the begin- ning of this section.

CALIFORNIA PROPOSI- TION 65 WARNING

Engine oil contains chemicals known to the State of California to cause cancer, birth defects, and reproductive harm. Used engine oil may cause irrita- tion or cancer of the skin if left in contact with the skin for prolonged periods of time. Used engine oil contains chemicals that have caused cancer in laboratory ani- mals. Always protect your skin by washing your hands thoroughly with soap and warm water as soon as possible after handling used oil.

ENGINE COOLANT The high-pressure cooling system has a reservoir filled with year-round antifreeze coolant. The reservoir is filled at the fac- tory. Check the antifreeze protection and coolant level at least once a year, at the beginning of the winter season, and before traveling to a colder climate.

Checking the coolant level

WARNING - Removing radiator cap

(cid:129) Never attempt to remove the radi- ator cap while the engine is oper- ating or hot. Doing so might lead to cooling system and engine damage. Also, hot coolant or steam could cause serious per- sonal injury.

(Continued)

22

(Continued) (cid:129) Turn the engine off and wait until it cools down. Use extreme care when removing the radiator cap. Wrap a thick towel around it, and turn it counterclockwise slowly to the first stop. Step back while the pressure is released from the cooling system. When you are sure all the pressure has been released, press down on the cap, using a thick towel, and continue turning counterclockwise to remove it.

(cid:129) Even if the engine is not operat- ing, do not remove the radiator cap or the drain plug while the engine and radiator are hot. Hot coolant and steam may still blow out under pressure, causing seri- ous injury.

level should be

OLM079006
Check the condition and connections of all cooling system hoses and heater hoses. Replace any swollen or deterio- rated hoses. The coolant filled between F and L marks on the side of the coolant reservoir when the engine is cool. If the coolant level is low, add enough specified coolant to provide protection against freezing and corrosion. Bring the level to F, but do not overfill. If frequent additions are required, see an authorized HYUNDAI dealer for a cooling system inspection.

Maintenance

Recommended engine coolant (cid:129) When adding coolant, use only deion- ized water or soft water for your vehicle and never mix hard water in the coolant filled at the factory. An improp- er coolant mixture can result in serious malfunction or engine damage.

(cid:129) The engine in your vehicle has alu- minum engine parts and must be pro- tected by an ethylene-glycol-based coolant to prevent corrosion and freez- ing.

(cid:129) DO NOT USE alcohol or methanol coolant or mix them with the specified coolant.

(cid:129) Do not use a solution that contains more than 60% antifreeze or less than 35% antifreeze, which would reduce the effectiveness of the solution.

7 23

Maintenance

For mixture percentage, refer to the fol- lowing table.

Ambient

Temperature

5°F (-15°C) -13°F (-25°C) -31°F (-35°C) -49°F (-45°C)

Mixture Percentage (volume)

Antifreeze

Water

35
40
50
60

65
60
50
40

Changing the coolant Have coolant changed by an authorized HYUNDAI dealer according the Maintenance Schedule at the beginning of this section.

to

CAUTION

Put a thick cloth around the radiator cap before refilling the coolant in order to prevent the coolant from overflowing into engine parts such as the generator.

WARNING - Coolant

(cid:129) Do not use radiator coolant or antifreeze in the washer fluid reservoir.

(cid:129) Radiator coolant can severely obscure visibility when sprayed on the windshield and may cause loss of vehicle control or damage to paint and body trim.

OLM079007

WARNING - Radiator cap

Do not remove the radiator cap when the engine and radiator are hot. Scalding hot coolant and steam may blow out under pres- sure causing serious injury.

24

BRAKE/CLUTCH (IF EQUIPPED) FLUID

If the level is low, add fluid to the MAX level. The level will fall with accumulated mileage. This is a normal condition asso- ciated with the wear of the brake linings and/or clutch disc (if equipped). If the fluid level is excessively low, have the brake/clutch* system checked by an authorized HYUNDAI dealer.

Use only the specified brake/clutch* fluid. (Refer to “Recommended lubricants and capacities”in section 8.)

Never mix different types of fluid.

WARNING - Loss of brake/clutch* fluid

In the event the brake/clutch* system requires frequent additions of fluid, the vehicle should be inspected by an authorized HYUNDAI dealer.

OLM079008N

fluid

Checking the brake/clutch* fluid level Check the fluid level in the reservoir peri- odically. The level should be between MAX and MIN marks on the side of the reservoir. Before removing the reservoir cap and adding brake/clutch* fluid, clean the area around the reservoir cap thoroughly to prevent brake/clutch* fluid contamina- tion. * : if equipped

Maintenance

WARNING - Brake/clutch*

fluid

and

changing

When adding brake/clutch* fluid, handle it care- fully. Do not let it come in contact with your eyes. If brake/clutch* fluid should come in contact with your eyes, immediately flush them with a large quantity of fresh tap water. Have your eyes examined by a doc- tor as soon as possible.

CAUTION

Do not allow brake/clutch* fluid to contact the vehicle's body paint,as paint damage will result. Brake/clutch* fluid,which has been exposed to open air for an extended time should never be used as its quality cannot be guaranteed. It should be disposed of properly. Don't put in the wrong kind of fluid. A few drops of mineral-based oil, such as engine oil, in your brake/clutch* system can damage brake/clutch* system parts.

7 25

Maintenance

WASHER FLUID

OLM079010

Checking the washer fluid level Check the fluid level in the washer fluid reservoir and add fluid if necessary. Plain water may be used if washer fluid is not available. However, use washer solvent with antifreeze characteristics in cold cli- mates to prevent freezing.

WARNING - Coolant

(cid:129) Do not use radiator coolant or antifreeze in the washer fluid reservoir.

(cid:129) Radiator coolant can severely obscure visibility when sprayed on the windshield and may cause loss of vehicle control or damage to paint and body trim.

(cid:129) Windshield washer fluid agents contain some amounts of alcohol and can be flammable under cer- tain circumstances. Do not allow sparks or flame to contact the washer fluid or the washer fluid reservoir. Damage to the vehicle or occupants could occur.

(cid:129) Windshield washer fluid is poi- sonous to humans and animals. Do not drink and avoid contacting windshield washer fluid. Serious injury or death could occur.

26

PARKING BRAKE

Maintenance

OLM059014

OLM059016

Checking the parking brake Type A Check whether the stroke is within spec- ification when the parking brake pedal is depressed with 44 lb (20 kg, 196 N) of force. Also, the parking brake alone should securely hold the vehicle on a fair- ly steep grade. If the stroke is more or less than specified, have the parking brake adjusted by an authorized HYUNDAI dealer.

Stroke : 4 notch

Type B Check the stroke of the parking brake by counting the number of “clicks’’ heard while fully applying it from the released position. Also, the parking brake alone should securely hold the vehicle on a fair- ly steep grade. If the stroke is more or less than specified, have the parking brake adjusted by an authorized HYUNDAI dealer.

Stroke : 6 “clicks’’ at a force of

44 lbs (20 kg, 196 N).

7 27

Maintenance

AIR CLEANER

OLM079012N

Filter replacement It must be replaced when necessary, and should not be washed. You can clean the filter when inspecting the air cleaner element. Clean the filter by using compressed air.

OLM079013N 1. Loosen the air cleaner cover attaching

clips and open the cover.

OLM079014

2. Wipe the inside of the air cleaner. 3. Replace the air cleaner filter. 4. Lock the cover with the cover attaching

clips.

Replace the filter according to the Maintenance Schedule. If the vehicle is operated in extremely dusty or sandy areas, replace the ele- ment more often than the usual recom- mended intervals.(Refer to “Maintenance under severe usage conditions” in this section.)

28

CAUTION

(cid:129) Do not drive with the air cleaner removed;this will result in exces- sive engine wear.

(cid:129) When removing the air cleaner fil- ter, be careful that dust or dirt does not enter the air intake, or damage may result.

(cid:129) Use a HYUNDAI genuine part.Use of non-genuine parts could dam- age the air flow sensor.

CLIMATE CONTROL AIR FILTER Filter inspection The climate control air filter should be replaced according to the Maintenance Schedule. If the vehicle is operated in severely air-polluted cities or on dusty rough roads for a long period, it should be frequently and replaced earlier. When you replace the climate control air filter, replace it per- forming the following procedure, and be careful to avoid damaging other compo- nents.

inspected more

Maintenance

OLM079015

Filter replacement 1. Open the glove box and remove the

support rod (1).

7 29

Maintenance

OLM079016
2. With the glove box open, remove the

stoppers on both sides.

OLM079017
3. Remove the climate control air filter case pulling out both sides of the cover.

OLM079018

4. Replace the climate control air filter. 5. Reassemble in the reverse order of

disassembly.

✽✽ NOTICE When replacing the climate control air filter install it properly. Otherwise, the system may produce noise and the effec- tiveness of the filter may be reduced.

30

WIPER BLADES

1JBA5122

Blade inspection ✽✽ NOTICE Commercial hot waxes applied by auto- matic car washes have been known to make the windshield difficult to clean.

Maintenance

Contamination of either the windshield or the wiper blades with foreign matter can reduce the effectiveness of the wind- shield wipers. Common sources of con- tamination are insects, tree sap, and hot wax treatments used by some commer- cial car washes. If the blades are not wip- ing properly, clean both the window and the blades with a good cleaner or mild detergent, and rinse thoroughly with clean water.

Blade replacement When the wipers no longer clean ade- quately, the blades may be worn or cracked, and require replacement.

CAUTION

To prevent damage to the wiper arms or other components, do not attempt to move the wipers manual- ly.

CAUTION

To prevent damage to the wiper blades, do not use gasoline, kerosene, paint thinner, or other solvents on or near them.

CAUTION

The use of a non-specified wiper blade could result in wiper malfunc- tion and failure.

7 31

Maintenance

OLM079200

Front windshield wiper blade 1. Raise the wiper arm and turn the wiper blade assembly to expose the plastic locking clip.

CAUTION

Do not allow the wiper arm to fall against the windshield,since it may chip or crack the windshield.

32

OLM079201
2. Compress the clip and slide the blade

assembly downward.

OLM079202

3. Lift it off the arm. 4. Install the blade assembly in the

reverse order of removal.

OHM078062

Rear window wiper blade 1. Raise the wiper arm and pull out the

wiper blade assembly.

OHM078063
2. Install the new blade assembly by inserting the center part into the slot in the wiper arm until it clicks into place. 3. Make sure the blade assembly is installed firmly by trying to pull it slight- ly.

To prevent damage to the wiper arms or other components, have an authorized HYUNDAI dealer replace the wiper blade.

Maintenance

7 33

Maintenance

BATTERY

OLM079019N

For best battery service (cid:129) Keep the battery securely mounted. (cid:129) Keep the battery top clean and dry. (cid:129) Keep the terminals and connections clean, tight, and coated with petroleum jelly or terminal grease.

(cid:129) Rinse any spilled electrolyte from the battery immediately with a solution of water and baking soda.

(cid:129) If the vehicle is not going to be used for an extended time, disconnect the bat- tery cables.

34

WARNING - Battery dangers

Always read the following instructions carefully when handling a battery. Keep lighted cigarettes and all other flames or sparks away from the battery. Hydrogen, a highly com- bustible gas, is always present in battery cells and may explode if ignited. Keep batteries out of the reach of children because batteries contain highly corrosive SULFURIC ACID. Do not allow battery acid to contact your skin, eyes, clothing or paint finish.

(Continued)

(Continued)

If any electrolyte gets into your eyes, flush your eyes with clean water for at least 15 minutes and get immedi- ate medical attention. If electrolyte gets on your skin, thoroughly wash the contacted area. If you feel a pain or a burning sensa- tion, get medical attention immediately. Wear eye protection when charging or working near a battery. Always provide ventilation when working in an enclosed space. An inappropriately dis- posed battery can be harm- ful to the environment and human health. Dispose the battery according to your local law(s) or regulation.

(Continued)

CALIFORNIA PROPOSI- TION 65 WARNING

Battery posts, terminals, and relat- ed accessories contain lead and lead compounds, chemicals known to the State of California to cause cancer, birth defects, and reproduc- tive harm. Batteries also contain other chemicals known to the State of California to cause cancer. Wash hands after handling.

(Continued) (cid:129) When lifting a plastic-cased bat- tery, excessive pressure on the case may cause battery acid to leak, resulting in personal injury. Lift with a battery carrier or with your hands on opposite corners. (cid:129) Never attempt to recharge the battery when the battery cables are connected.

(cid:129) The electrical ignition system works with high voltage. Never touch these components with the engine running or the ignition switched on.

Failure to follow the above warn- ings can result in serious bodily injury or death.

Maintenance

Battery recharging Your vehicle has a maintenance-free, calcium-based battery. (cid:129) If the battery becomes discharged in a short time (because, for example, the headlights or interior lights were left on while the vehicle was not in use), recharge it by slow charging (trickle) for 10 hours.

(cid:129) If the battery gradually discharges because of high electric load while the vehicle is being used, recharge it at 20- 30A for two hours.

WARNING - Recharging

battery

recharging

When the battery, observe the following precautions: (cid:129) The battery must be removed from the vehicle and placed in an area with good ventilation.

(cid:129) Do not allow cigarettes, sparks,

or flame near the battery.

(cid:129) Watch the battery during charg- ing, and stop or reduce the charg- ing rate if the battery cells begin gassing (boiling) violently or if the temperature of the electrolyte of any cell exceeds 120°F (49°C). (Continued)

7 35

Maintenance

(Continued) (cid:129) Wear eye protection when check-

ing the battery during charging.

(cid:129) Disconnect the battery charger in

the following order.

1. Turn off the battery charger main

switch.

2. Unhook the negative clamp from

the negative battery terminal.

3. Unhook the positive clamp from

the positive battery terminal.

Reset items Items should be reset after the battery has been discharged or the battery has been disconnected. (cid:129) Auto up/down window (See section 4) (cid:129) Sunroof (See section 4) (cid:129) Trip computer (See section 4) (cid:129) Climate control system

(See section 4)

(cid:129) Clock (See section 4) (cid:129) Audio (See section 4)

WARNING

(cid:129) Before performing maintenance or recharging the battery, turn off all accessories and stop the engine.

(cid:129) The negative battery cable must be removed first and installed last when the battery is discon- nected.

36

TIRES AND WHEELS Tire care For proper maintenance, safety, and maximum fuel economy, you must always maintain recommended tire inflation pressures and stay within the load limits and weight distribution recommended for your vehicle.

Recommended cold tire inflation pressures All tire pressures (including the spare) should be checked when the tires are cold. “Cold Tires” means the vehicle has not been driven for at least three hours or driven less than one mile (1.6 km). Recommended pressures must be maintained for the best ride, vehicle handling, and minimum tire wear. For recommended inflation pressure, refer to “Tire and wheels” in section 8.

Maintenance

CAUTION

(cid:129) Underinflation also results in excessive wear,poor handling and reduced fuel economy. Wheel deformation also is possible.Keep your tire pres- sures at the proper levels.If a tire frequently needs refilling, have it checked by an author- ized HYUNDAI dealer.

(cid:129) Overinflation produces a harsh ride, excessive wear at the center of the tire tread,and a greater possibility of dam- age from road hazards.

OLM089008N All specifications (sizes and pres- sures) can be found on a label attached to the driver’s side center pillar.

WARNING - Tire underin-

flation

Severe underinflation can lead to severe heat build-up, causing blowouts, tread separation and other tire failures that can result in the loss of vehicle control leading to severe injury or death. This risk is much higher on hot days and when driving for long periods at high speeds.

7 37

CAUTION - Tire pressure Always observe the following: (cid:129) Check tire pressure when the tires are cold. (After vehicle has been parked for at least three hours or hasn't been driven more than one mile (1.6
km) since startup.)

(cid:129) Check the pressure of your spare tire each time you check the pressure of other tires.

(cid:129) Never overload your vehicle. Be careful not to overload a vehicle luggage rack if your vehicle is equipped with one. (cid:129) Worn,old tires can cause acci- dents. If your tread is badly worn, or if your tires have been damaged,replace them.

Checking tire inflation pressure Check your tires once a month or more. Also, check the tire pressure of the spare tire.

How to check Use a good quality gage to check tire pressure. You can not tell if your tires are properly inflated simply by look- ing at them. Radial tires may look properly inflated even when they're underinflated. Check the tire's inflation pressure when the tires are cold. - "Cold" means your vehicle has been sitting for at least three hours or driven no more than 1 mile (1.6 km).

Maintenance

CAUTION

(cid:129) Warm tires normally exceed recommended cold tire pres- sures by 4 to 6 psi (28 to 41
kPa). Do not release air from warm tires to adjust the pres- sure or the tires will be under- inflated.

(cid:129) Be sure to reinstall the tire inflation valve caps. Without the valve cap,dirt or moisture could get into the valve core and cause air leakage. If a valve cap is missing,install a new one as soon as possible.

WARNING - Tire Inflation Overinflation or underinflation can reduce tire life, adversely affect vehicle handling, and lead to sudden tire failure. This could result in loss of vehicle control and potential injury.

38

Remove the valve cap from the tire valve stem. Press the tire gage firm- ly onto the valve to get a pressure measurement. If the cold tire inflation pressure matches the recommended pressure on the tire and loading information label, no further adjust- ment is necessary. If the pressure is low, add air until you reach the rec- ommended amount. If you overfill the tire, release air by pushing on the metal stem in the