service station and inflate to the correct pressure. If it is too high, adjust it until it is correct. Always reinstall the valve cap after checking or adjusting tire pressure. If the cap is not replaced, air may leak from the tire. If you lose a valve cap, buy another and install it as soon as possible.
CAUTION:
Your car can be damaged if towed incor- rectly!
If your car has to be towed, it should be done by your Hyundai dealer or a commercial tow truck service. This will help assure that your car is not damaged in towing. Also, professionals are generally aware of state and local laws govern- ing towing. In any case, rather than risk damage to your car, it is suggested that you show this information to the tow truck operator. Be sure that a safety chain system is used and that all state and local laws are observed.
xgflhma-3.p65
11
6/16/04, 3:00 PM
WHAT TO DO IN AN EMERGENCY
12
D080C02A-AAT Towing a Car With Automatic Transaxle
EMERGENCY TOWING
D080D01E-AAT
o NOT OK
FOR AUTOMATIC
TRANSAXLE EQUIPPED VEHICLE
HXG552J
CAUTION:
A car with an automatic transaxle should never be towed from the rear with the front wheels on the ground. This can cause se- rious damage to the transaxle. If the car must be towed from the rear, a towing dolly must be used under the front wheels.
If the car is being towed with the rear wheels on the ground, be sure the parking brake is re- leased.
o OK FOR AUTOMATIC TRANSAXLE
EQUIPPED VEHICLE
D080C01L
NOTE: Before towing, check the level of the transaxle fluid. If it is below the "HOT" mark on the dipstick, add fluid. If you cannot add fluid, a towing dolly must be used as de- scribed above.
D080D01L For emergency towing when no commercial tow vehicle is available, attach a tow cable, chain or strap to one of the towing hooks under the front of your car. Do not attempt to tow your vehicle in this manner on any unpaved surface. This could result in serious damage to your car. Nor should towing be attempted if the wheels, drive train, axles, steering or brakes are dam- aged. Before towing, be sure the transaxle is in neutral and the key is in "ACC" (with the engine off) or in the "ON" position (with the engine running). A driver must be in the towed car to steer it and operate the brakes.
xgflhma-3.p65
12
6/16/04, 3:00 PM
WHAT TO DO IN AN EMERGENCY
13
IF YOU LOSE YOUR KEYS
D120A01A-AAT If you lose your keys, many Hyundai dealers can make you a new key if you have your key number. If you lock the keys inside your car and you cannot obtain a new key, many Hyundai dealers can use special tools to open the door for you.
CAUTION:
If the car is being towed with all four wheels
on the ground, it can be towed only from the
front. Be sure that the transaxle is in neutral.
Do not tow at speeds greater than 30 mph
(50 km/h) and for more than 15 miles (25
km). Be sure the steering is unlocked by
placing the key in the "ACC" position. A
driver must be in the towed vehicle to
operate the steering and brakes.
xgflhma-3.p65
13
6/16/04, 3:00 PM
CORROSION PREVENTION &
APPEARANCE CARE
Corrosion Protection ..................................................... 4-2
To Help Prevent Corrosion ........................................... 4-3
Washing and Waxing .................................................... 4-4
Cleaning the Interior ...................................................... 4-5
xgflhma-4.p65
6/16/04, 2:59 PM
44 CORROSION PREVENTION AND APPEARANCE CARE
CORROSION PROTECTION
E010A01A-AAT Protecting Your Hyundai from Corro- sion
By using the most advanced design and con- struction practices to combat corrosion, Hyundai produces cars of the highest quality. However, this is only part of the job. To achieve the long-term corrosion resistance your Hyundai can deliver, the owner's cooperation and assistance is also required.
E010B01A-AAT Common Causes of Corrosion
E010D01A-AAT Moisture Breeds Corrosion
The most common causes of corrosion on your car are:
o Road salt, dirt and moisture that is allowed to
accumulate underneath the car.
o Removal of paint or protective coatings by stones, gravel, abrasion or minor scrapes and dents which leave unprotected metal exposed to corrosion.
E010C01A-AAT High-Corrosion Areas
If you live in an area where your car is regularly exposed to corrosive materials, corrosion pro- tection is particularly important. Some of the common causes of accelerated corrosion are road salts, dust control chemicals, ocean air and industrial pollution.
Moisture creates the conditions in which corro- sion is most likely to occur. For example, cor- rosion is accelerated by high humidity, particu- larly when temperatures are just above freez- ing. In such conditions, the corrosive material is kept in contact with the car surfaces by mois- ture that is slow to evaporate. Mud is particularly corrosive because it is slow to dry and holds moisture in contact with the vehicle. Although the mud appears to be dry, it can still retain the moisture and promote corro- sion. High temperatures can also accelerate corro- sion of parts that are not properly ventilated so the moisture can be dispersed. For all these reasons, it is particularly important to keep your car clean and free of mud or accumulations of other materials. This applies not only to the visible surfaces but particularly to the underside of the car.
xgflhma-4.p65
6/16/04, 2:59 PM
o When cleaning lower door panels, rocker panels and frame members, be sure that drain holes are kept open so that moisture can escape and not be trapped inside to ac- celerate corrosion.
E020C01A-AAT Keep Your Garage Dry
Don't park your car in a damp, poorly ventilated garage. This creates a favorable environment for corrosion. This is particularly true if you wash your car in the garage or drive it into the garage when it is still wet or covered with snow, ice or mud. Even a heated garage can contrib- ute to corrosion unless it is well ventilated so moisture is dispersed.
CORROSION PREVENTION AND APPEARANCE CARE
CORROSION PREVENTION AND APPEARANCE CARE 4
E020D02A-AAT Keep Paint and Trim in Good Condition
Scratches or chips in the finish should be covered with "touch-up" paint as soon as pos- sible to reduce the possibility of corrosion. If bare metal is showing through, the attention of a qualified body and paint shop is recommended.
Bird droppings : Bird droppings are highly cor- rosive and may damage painted surfaces in just a few hours. Always remove bird droppings as soon as possible.
E020E01A-AAT Don't Neglect the Interior
Moisture can collect under the floor mats and carpeting to cause corrosion. Check under the mats periodically to be sure the carpeting is dry. Use particular care if you carry fertilizers, clean- ing materials or chemicals in the car. These should be carried only in proper contain- ers and any spills or leaks should be cleaned up, flushed with clear water and thoroughly dried.
TO HELP PREVENT CORROSION
E020A01A-AAT You can help prevent corrosion from getting started by observing the following:
E020B01A-AAT Keep Your Car Clean
The best way to prevent corrosion is to keep your car clean and free of corrosive materials. Attention to the underside of the car is particu- larly important.
o If you live in a high-corrosion area — where road salts are used, near the ocean, areas with industrial pollution, acid rain, etc.—, you should take extra care to prevent corrosion. In winter, hose off the underside of your car at least once a month and be sure to clean the underside thoroughly when winter is over.
o When cleaning underneath the car, give particular attention to the components under the fenders and other areas that are hidden from view. Do a thorough job; just dampening the accumulated mud rather than washing it away will accelerate corrosion rather than prevent it. Water under high pressure and steam are particularly effective in removing accumulated mud and corrosive materials.
xgflhma-4.p65
6/16/04, 2:59 PM
44 CORROSION PREVENTION AND APPEARANCE CARE
WASHING AND WAXING
E030A01GK-AAT Washing Your Hyundai
Never wash your car when the surface is hot from being in the sun. Always wash your car in the shade.
Wash your car frequently. Dirt is abrasive and can scratch the paint if it is not removed. Air pollution or acid rain may damage the paint and trim through chemical action if pollutants are allowed to remain in contact with the surface. If you live near the ocean or in an area where road salts or dust control chemicals are used, you should pay particular attention to the underside of the car. Start by rinsing the car to remove dust and loose dirt. In winter, or if you have driven through mud or muddy water, be sure to thor- oughly clean the underside as well. Use a hard direct stream of water to remove accumulations of mud or corrosive materials. High pressure car washes may cause water to enter your vehicle. Use a good quality car-washing solu- tion and follow the manufacturer's directions on the package. These are available at your Hyundai dealer or auto parts outlet. Don't use strong household detergents, gasoline, strong solvents or abrasive cleaning powders as these may damage the finish. Use a clean sponge or cloth, rinse it frequently and don't damage the finish by rubbing too hard. For stubborn spots, dampen them frequently and remove them a little at a time.
To clean whitewall tires, use a stiff brush or soapy steel-wool scouring pad.
To clean plastic wheel covers, use a clean sponge or soft cloth and water.
To clean cast aluminum alloy wheels, use a mild soap or neutral detergent. Do not use abrasive cleaners. Protect the bare-metal surfaces by cleaning, polishing and waxing. Because alumi- num is subject to corrosion, be sure to give aluminum alloy wheels special attention in win- ter. If you drive on salted roads, clean the wheels thoroughly afterwards.
After washing, be sure to rinse thoroughly. If soapy water dries on the finish, streaking will result.
When the weather is warm and the humidity low, you may find it necessary to rinse each section immediately after washing to avoid streaking.
After rinsing, dry the car using a damp chamois or soft, absorbent cloth. The reason for drying the car is to remove water from the car so it will dry without water spots. Don't rub, this can damage the finish.
If you find any nicks or scratches in the paint, use touch-up paint to cover them to prevent corrosion. To protect the paintwork of the car against corrosion, you must clean your Hyundai (at least once a month). Give special attention to the removal of salt, mud and other sub- stances on the underside of the splashboards of the car. Make sure that the outlets and the underside of the doors are open. Paint damage can be caused by small accumulation of tar, industrial precipitation, tree resin, insects and bird droppings, when not removed immediately. If water alone is not strong enough to remove the accumulated dirt, use a mild car washing solu- tion. Be sure to rinse the surface after washing to remove the solution. Never allow the solution to dry on the painted surfaces.
xgflhma-4.p65
6/16/04, 2:59 PM
CORROSION PREVENTION AND APPEARANCE CARE
CORROSION PREVENTION AND APPEARANCE CARE 4
CLEANING THE INTERIOR
E040A01A-AAT To Clean the Vinyl Upholstery
To clean the vinyl upholstery, first remove loose dirt and dust with a vacuum cleaner. Then apply a solution of mild soap or detergent and water using a clean sponge or soft cloth. Allow this to stay on the surface to loosen the dirt, then wipe with a clean damp sponge or cloth. If all the dirt stains are not removed, repeat this procedure until the upholstery is clean. Do not use gaso- line, solvent, paint thinner or other strong clean- ers.
E030B01A-AAT Spot Cleaning
E030E01A-AAT Maintaining Bumpers
Special precautions must be observed to pre- serve the appearance of the bumpers on your Hyundai. They are:
o Be careful not to spill battery electrolyte or hydraulic brake fluid on the bumpers. If you do, wash it off immediately with clear water. o Be gentle when cleaning the bumper sur- faces. They are made of soft plastic and the surface can be damaged if mistreated. Do not use abrasive cleaners. Use warm water and mild soap or car-washing solution.
o Do not expose the bumpers to high tem- peratures. For example, if you have your car repainted, do not leave the bumpers on the car if the car is going to be placed in a high- temperature paint booth.
Don't use gasoline, strong solvents or corro- sive cleaning agents. These can damage the finish of the car. To remove road tar, use turpentine on a clean, soft cloth. Be gentle. To remove dead insects or tree sap, use warm water and mild soap or car-washing solution. Soak the spot and rub gently. If the paint has lost its luster, use a commercial car-cleaning polish.
E030C01A-AAT Polishing and Waxing
Always wash and dry the car before polishing or waxing or using a combination cleaner and wax. Use a good quality commercial product and follow the manufacturer's directions on the container. Polish and wax the bright trim pieces as well as the paint.
E030D01A-AAT When to Wax Again
You should polish and wax the car again when water no longer beads on a clean surface but spreads out over a larger area.
xgflhma-4.p65
6/16/04, 2:59 PM
44 CORROSION PREVENTION AND APPEARANCE CARE
E040B01A-AAT To Clean the Leather Upholstery (If Installed)
In the normal course of use, leather upholstered surfaces will, like any material, pick-up dust and dirt. This dust and dirt must be cleaned off or it may work into the surface of the leather, caus- ing damage.
Fine leather needs care, and should be cleaned when necessary. Washing leather thoroughly with soap and water will keep your leather lustrous, beautiful and ensure you have many years of wear. Take a piece of cheese cloth and using any mild soap and lukewarm water, work up a good lather. Thoroughly wash the leather. Wipe clean with a slightly damp cloth and dry with soft cloth. Do this as often as the leather becomes soiled.
During tanning operations, sufficient oils are incorporated through processing that none need be applied during the life of the leather. Oil applied to the finished surface will in no way help the leather and may do more harm than good. Varnishes and furniture polishes should never be used under any conditions.
E040C01A-AAT Cleaning the Carpets
E040E01A-AAT Cleaning the Windows
Use a foam-type carpet cleaner. Cleaners of this type are available in aerosol cans in liquid form or powder. Read the instructions and follow them exactly. Using a vacuum cleaner with the appropriate attachment, remove as much dirt from the carpets as possible. Apply the foam following the manufacturer's direc- tions, then rub in overlapping circles. Do not add water. These cleaners work best when the carpet is kept as dry as possible.
You may use any household window cleaner on the windows. However, when cleaning the in- side of the rear window be careful not to damage the rear window defroster wiring.
E050A01A-AAT Any Questions?
If you have any questions about the care of your car, consult your Hyundai dealer.
E040D01A-AAT Cleaning the Seat Belts
To clean the seat belts, use a cloth or sponge with mild soap or detergent and warm water. Do not use strong detergents, dye, bleach or abra- sive materials on the seat belts as this may weaken the fabric. While cleaning the belts, inspect them for ex- cessive wear, cuts, fraying or other signs of damage and replace them if necessary.
xgflhma-4.p65
6/16/04, 2:59 PM
VEHICLE MAINTENANCE REQUIREMENTS
Maintenance Intervals ................................................... 5-2
Scheduled Maintenance ................................................ 5-4
Maintenance Under Severe Usage Conditions ............. 5-6
Explanation of Scheduled Maintenance Items .............. 5-7
55
xgflhma-5.p65
6/16/04, 2:59 PM
5 VEHICLE MAINTENANCE REQUIREMENTS MAINTENANCE INTERVALS
F010A01A-AAT Service Requirements
F010B01A-AAT Maintenance Requirements
To ensure that you receive the greatest number of miles of satisfying operation from your Hyundai, certain maintenance procedures must be per- formed. Although careful design and engineer- ing have reduced these to a minimum, those that are required are of the utmost importance. It is your responsibility to have these mainte- nance procedures performed to comply with the terms of the warranties covering your new Hyundai. The Owner's Handbook supplied with your new vehicle provides further information about these warranties.
The maintenance required for your Hyundai can be divided into three main areas:
o Specified scheduled procedures o General checks o Do-it-yourself maintenance
F010C01A-AAT Specified Scheduled Procedures
These are the procedures such as inspections, adjustments and replacements that are listed in the maintenance charts starting on page 5-4. These procedures must be performed at the intervals shown in the maintenance schedule to assure that your warranty remains in effect. Although it is strongly recommended that they be performed by the trained technicians at your Hyundai dealer, these procedures may be per- formed at any qualified service facility. It is suggested that genuine Hyundai service parts be used for any required repairs or re- placements. Other parts of equivalent quality such as engine oil, engine coolant, auto transaxle oil, brake fluid and so on which are not supplied by Hyundai Motor Company or its distributor
may be used without affecting your warranty coverage but you should always be sure these are equivalent to the quality of the original Hyundai parts. Your Owner's Handbook pro- vides further information about your warranty coverage.
F010D01A-AAT General Checks
These are the regular checks you should per- form when you drive your Hyundai or you fill the fuel tank. A list of these items will be found on page 6-3.
F010E01A-AAT Do-It-Yourself Maintenance
If you are mechanically inclined, own a few tools that are required and want to take the time to do so, you can inspect and service a number of items. For more information about doing it your- self, see Section 6.
xgflhma-5.p65
6/16/04, 2:59 PM
F010F01A-AAT A Few Tips
o Whenever you have your Hyundai serviced, keep copies of the service records in your glovebox. This will help ensure that you can document that the required procedures have been performed to keep your warranties in effect. This is especially important when service is not performed by an authorized Hyundai dealer.
o If you choose to do your own maintenance and repairs, you may find it helpful to have an official Hyundai Shop Manual. A copy of this publication may be purchased at your Hyundai dealer's parts department.
VEHICLE MAINTENANCE REQUIREMENTS
F020A02Y-AAT SCHEDULED MAINTENANCE REQUIREMENTS
o Inspection should be performed any time a malfunction is experienced or suspected. o Receipts for all emission control system services should be retained to demonstrate compliance with conditions of the emissions system warranty.
o After 120 months or 150,000 miles (240,000
km), continue to follow the prescribed main-
tenance intervals.
o For severe usage maintenance require-
ments, see page 5-6 of this section.
xgflhma-5.p65
6/16/04, 2:59 PM
5 VEHICLE MAINTENANCE REQUIREMENTS
SCHEDULED MAINTENANCE
F030A01A-AAT The following maintenance services must be performed to ensure good emission control and performance. Keep receipts for all vehicle emission services to protect your warranty. Where both mileage and time are shown, the frequency of service is determined by whichever occurs first.
F030B02Y-AAT R :Replace I : Inspect and, after Inspection, clean, adjust, repair or replace if necessary.
No.
DESCRIPTION
KILOMETERS X 1000
MILES X 1000
MONTHS
7.5
12
15
24
12
22.5
36
18
30
48
24
37.5
45
52.5
60
30
72
36
84
42
60
96
48
67.5
75
82.5
90
97.5
105
112.5
120
127.5
135
142.5
150
108
120
132
144
156
168
180
192
204
216
228
240
54
60
66
72
78
84
90
96
102
108
114
120
EMISSION CONTROL ITEMS
ENGINE OIL AND FILTER
FUEL FILTER
FUEL LINES, FUEL HOSES AND CONNECTIONS
VACUUM AND CRANKCASE VENTILATION HOSES
VAPOR HOSE AND FUEL FILLER CAP
AIR CLEANER FILTER
SPARK PLUGS (PLATINUM COATED)
xgflhma-5.p65
6/16/04, 2:59 PM
VEHICLE MAINTENANCE REQUIREMENTS
F030C03L-AAT R : Replace I : Inspect and, after inspection, clean, adjust, repair or replace if necessary
No.
DESCRIPTION
MILES X 1000
KILOMETERS X 1000
MONTHS
GENERAL ITEMS DRIVE BELT (ALT, P/STR'G, A/CON) ENGINE COOLANT TIMING BELT AUTOMATIC TRANSAXLE FLUID AND FILTER BRAKE FLUID BRAKE HOSES AND LINES REAR BRAKE DRUMS/LININGS, PARKING BRAKE BRAKE PADS, CALIPERS AND ROTORS EXHAUST PIPE AND MUFFLER SUSPENSION MOUNTING BOLTS STEERING GEAR BOX, LINKAGE & BOOTS/LOWER ARM BALL JOINT, UPPER ARM BALL JOINT POWER STEERING PUMP AND HOSES DRIVESHAFTS AND BOOTS AIR CONDITIONING REFRIGERANT AIR CONDITIONER FILTER (FOR EVAPORATOR AND BLOWER UNIT)
10
11
12
13
14
15
7.5
12
15
24
12
22.5
36
18
30
48
24
37.5
60
30
52.5
84
42
45
72
36
60
96
48
67.5
108
54
75
120
60
82.5
132
66
90
144
72
97.5
156
78
105
168
84
112.5
180
90
120
192
96
127.5
204
102
135
216
108
142.5
228
114
150
240
120
See Note *1
Note : *1. FOR EVERY 12 MONTHS OR 12,000 MILES (20,000 KM), WHICHEVER OCCURS FIRST : "R"
xgflhma-5.p65
6/16/04, 2:59 PM
5 VEHICLE MAINTENANCE REQUIREMENTS
MAINTENANCE UNDER SEVERE USAGE CONDITIONS
F040A03L-AAT The following items must be serviced more frequently on cars normally used under severe driving conditions. Refer to the chart below for the appropriate maintenance intervals.
R : Replace I : Inspect and, after inspection, clean, adjust, repair or replace if necessary
MAINTENANCE ITEM
MAINTENANCE
OPERATION
MAINTENANCE INTERVALS
DRIVING
CONDITION
ENGINE OIL AND FILTER
AIR CLEANER FILTER
SPARK PLUGS
BRAKE PADS, CALIPERS AND ROTORS
REAR BRAKE DRUMS / LININGS, PARKING BRAKE
STEERING GEAR BOX, LINKAGE & BOOTS /
LOWER ARM BALL JOINT, UPPER ARM BALL JOINT
DRIVESHAFTS AND BOOTS
AUTOMATIC TRANSAXLE FLUID AND FILTER
AIR CONDITIONER FILTER
(FOR EVAPORATOR AND BLOWER UNIT)
SEVERE DRIVING CONDITIONS A - Repeated short distance driving B - Extensive idling C - Driving in dusty, rough roads D - Driving in areas using salt or other corrosive materials
or in very cold weather E - Driving in sandy areas
VERY 3,000 MILES (4,800 KM) OR 3 MONTHS
A, B, C, F, H
MORE FREQUENTLY
MORE FREQUENTLY
MORE FREQUENTLY
MORE FREQUENTLY
MORE FREQUENTLY
C, E
B, H
C, D, G, H
C, D, G, H
C, D, E, F, G
EVERY 7,500 MILES (12,000 KM) OR 6 MONTHS
C, E, F
EVERY 30,000 MILES (48,000 KM)
A, C, E, F, G, H, I
MORE FREQUENTLY
C, E
F - More than 50% driving in heavy city traffic during hot weather
above 90°F (32°C)
G - Driving in mountainous areas H - Towing a trailer
- Driving as a patrol car, taxi, vehicle towing or other commercial use
xgflhma-5.p65
6/16/04, 2:59 PM
EXPLANATION OF SCHEDULED MAINTENANCE ITEMS
VEHICLE MAINTENANCE REQUIREMENTS
F060A01A-AAT
F060M01A-AAT o Engine Oil and Filter
The engine oil and filter should be changed at the intervals specified in the maintenance sched- ule. If the car is being driven in severe condi- tions, more frequent oil and filter changes are required.
F060C01A-AAT o Fuel Filter
A clogged filter can limit the speed at which the vehicle may be driven, damage the emission system and cause hard starting. If an exces- sive amount of foreign matter accumulates in the fuel tank, the filter may require replacement more frequently. After installing a new filter, run the engine for several minutes, and check for leaks at the connections. Fuel filters should be installed by trained technicians.
F060B01A-AAT o Drive Belts
Inspect all drive belts for evidence of cuts, cracks, excessive wear or oil and replace if necessary. Drive belts should be checked periodically for proper tension and adjusted as necessary.
F060D01A-AAT o Fuel Lines, Fuel Hoses and Connec-
tions
Check the fuel lines, fuel hoses and connec- tions for leakage and damage. Have a trained technician replace any damaged or leaking parts immediately.
F060F01A-AAT o Vacuum, Crankcase
Ventilation Hoses
Inspect the surface of hoses for evidence of heat and/or mechanical damage. Hard and brittle rubber, cracking, tears, cuts, abrasions, and excessive swelling indicate deterioration. Particular attention should be paid to examine those hose surfaces nearest to high heat sources, such as the exhaust manifold.
Inspect the hose routing to assure that the hoses do not come in contact with any heat source, sharp edges or moving component which might cause heat damage or mechanical wear. Inspect all hose connections, such as clamps and couplings, to make sure they are secure, and that no leaks are present. Hoses should be replaced immediately if there is any evidence of deterioration or damage.
F060G01A-AAT o Vapor Hose and Fuel Filler Cap
The vapor hose and fuel filler cap should be inspected at those intervals specified in the maintenance schedule. Make sure that a new vapor hose or fuel filler cap is correctly re- placed.
F060H01A-AAT o Air cleaner filter
A Genuine Hyundai air cleaner filter is recom- mended when the filter is replaced.
F060J01A-AAT o Spark plugs
Make sure to install new spark plugs of the correct heat range.
xgflhma-5.p65
6/16/04, 2:59 PM
5 VEHICLE MAINTENANCE REQUIREMENTS
F060E01A-AAT o Timing belt
Inspect all parts related to the timing belt for damage and deformation. Replace any dam- aged parts immediately.
F070F01A-AAT o Brake Hoses and Lines
Visually check for proper installation, chafing, cracks, deterioration and any leakage. Replace any deteriorated or damaged parts immedi- ately.
F070J01A-AAT o Brake Pads, Calipers and Rotors
Check the pads for excessive wear, discs for run out and wear, and calipers for fluid leakage.
F070C01A-AAT o Coolant
The coolant should be changed at the intervals specified in the maintenance schedule.
F070E05A-AAT o Automatic Transaxle Fluid and Filter
The fluid level should be in the "HOT" range of the dipstick, after the engine and transaxle are at normal operating temperature. Check the automatic transaxle fluid level with the engine running and the transaxle in neutral, with the parking brake properly applied. Use HYUNDAI GENUINE ATF SP III, DIAMOND ATF SP III, SK ATF SP III or other brands approved by Hyundai Motor Co., when adding or changing fluid.
F070G02A-AAT o Brake Fluid
Check brake fluid level in the brake fluid reser-
voir. The level should be between "MIN" and
"MAX" marks on the side of the reservoir. Use
only hydraulic brake fluid conforming to DOT 3
or DOT 4.
F070H01A-AAT o Rear Brake Drums/Linings, Parking
Brake
Check the rear brake drums and linings for scoring, burning, leaking fluid, broken parts, and excessive wear. Inspect the parking brake system including the parking brake lever and cables. For detailed service procedures, refer to the Shop Manual.
F070K01A-AAT o Exhaust Pipe and Muffler
Visually inspect the exhaust pipes, muffler and hangers for cracks, deterioration, or damage. Start the engine and listen carefully for any exhaust gas leakage. Tighten connections or replace parts as necessary.
F070L01A-AAT o Suspension Mounting Bolts
Check the suspension connections for loose- ness or damage. Retighten to the specified torque.
xgflhma-5.p65
6/16/04, 2:59 PM
VEHICLE MAINTENANCE REQUIREMENTS
F070M01Y-AAT o Steering Gear Box, Linkage & Boots/ Lower Arm Ball Joint, Upper Arm Ball Joint
With the vehicle stopped and engine off, check for excessive free-play in the steering wheel. Check the linkage for bends or damage. Check the dust boots and ball joints for deterioration, cracks, or damage. Replace any damaged parts.
F070N02A-AAT o Power Steering Pump and Hoses
Check the power steering pump and hoses for leakage and damage. Replace any damaged or leaking parts immediately. Inspect the power steering belt for evidence of cuts, cracks, ex- cessive wear, oiliness and proper tension. Replace or adjust it if necessary.
F070P01A-AAT o Driveshafts and Boots
Check the driveshafts, boots and clamps for cracks, deterioration, or damage. Replace any damaged parts and, if necessary, repack the grease.
F070Q01A-AAT o Air Conditioning Refrigerant
Check the air conditioning lines and connec- tions for leakage and damage. Check air con- ditioning performance according to the relevant shop manual if necessary.
xgflhma-5.p65
6/16/04, 3:00 PM
Do-It-Yourself Maintenance
Engine Compartment .................................................... 6-2
General Checks ............................................................ 6-3
Checking the Engine Oil ............................................... 6-4
Changing the Oil and Filter ............................................ 6-5
Checking and Changing the Engine Coolant ................ 6-6
Spark Plugs .................................................................. 6-8
Changing the Air Cleaner Filter ..................................... 6-9
Checking the Transaxle Fluid ..................................... 6-11
Checking the Brakes .................................................. 6-12
Air Conditioning Care .................................................. 6-14
Changing the Conoitioner Air Filter
(For Evaporator and Blower Unit) ............................. 6-15
Checking Drive Belts .................................................. 6-17
Checking and Replacing Fuses .................................. 6-17
Power Steering Fluid Level ......................................... 6-20
Headlight Aiming Adjustment ...................................... 6-21
Replacement of Light Bulbs ........................................ 6-22
Bulb Wattage ............................................................... 6-31
Junction Box Description ............................................ 6-32
66
xgflhma-6.p65
6/16/04, 2:58 PM
6 DO-IT-YOURSELF MAINTENANCE
G010C01L-AAT ENGINE COMPARTMENT (3.5 V6)
1 2
CAUTION:
When inspecting or servicing the engine, you should handle tools and other heavy objects carefully so that the plastic cover of the engine is not damaged.
1. Brake fluid reservoir 2. Brake booster 3. Windshield washer fluid reservoir 4. Power steering fluid reservoir
9 10
11
12
5. Engine oil filler cap 6. Engine oil level dipstick 7. Radiator cap 8. Automatic transaxle fluid level dipstick
9. Air cleaner filter 10. Coolant reservoir cap 11. Battery 12. Under hood junction box
G010C01L
xgflhma-6.p65
6/16/04, 2:58 PM
GENERAL CHECKS
G020A01L-AAT Engine Compartment
G020B01A-AAT Vehicle Exterior
G020C01L-AAT Vehicle Interior
DO-IT-YOURSELF MAINTENANCE
The following should be checked regularly:
The following should be checked monthly:
o Engine oil level and condition o Transaxle fluid level and condition o Brake fluid level o Coolant level o Windshield washer fluid level o Accessory drive belt condition o Engine coolant hose condition o Fluid leaks (on or below components) o Power steering fluid level o Battery condition o Air filter condition
o Overall appearance and condition o Wheel condition and wheel nut torque o Exhaust system condition o Light condition and operation o Windshield glass condition o Wiper blade condition o Paint condition and body corrosion o Fluid leaks o Door and hood lock condition o Tire pressure and condition (including spare
tire)
The following should be checked each time when the vehicle is driven:
o Lights operation o Windshield wiper operation o Horn operation o Defroster, heating system operation (and air
conditioning, if installed)
o Steering operation and condition o Mirror condition and operation o Turn signal operation o Accelerator pedal operation o Brake operation, including parking brake o Automatic transaxle operation, including
"Park" mechanism operation
o Seat control condition and operation o Seat belt condition and operation o Sunvisor operation
If you notice anything that does not operate correctly or appears to be functioning incor- rectly, inspect it carefully and seek assistance from your Hyundai dealer if service is needed.
xgflhma-6.p65
6/16/04, 2:58 PM
6 DO-IT-YOURSELF MAINTENANCE
CHECKING THE ENGINE OIL
G030A01A-AAT Engine oil is essential to the performance and service of the engine. It is suggested that you check the oil level at least once a week in normal use and more often if you are on a trip or driving in severe conditions.
G030B01A-AAT Recommended Oil
G030C02A-AAT To Check the Oil Level
G030D01A-AAT Adding Oil
G030C01L-1
Before checking the oil, warm up the engine to the normal operating temperature and be sure your car is parked on level ground. Turn the engine off.
Wait five minutes, then remove the dipstick, wipe it off, fully reinsert the dipstick and withdraw it again. Then note the highest level the oil has reached on the dipstick. It should be between the upper ("FULL") and lower ("LOW") range.
SH, SG or SG/CD (API) multi-grade and fuel efficient oil is recommended.
G030A02A
G030D01L-1
If the oil level is close to or below the "LOW"
mark, add oil until it reaches the "FULL" mark.
To add oil:
1. Remove the oil filler cap by turning it counter-
2. Add oil, then check the level again. Do not
clockwise.
overfill.
3. Replace the cap by turning it clockwise.
The distance between the "FULL" and "LOW" marks is equal to about 1 quart of oil.
xgflhma-6.p65
6/16/04, 2:58 PM
CHANGING THE OIL AND FILTER
G040A01L-AAT
Oil filler cap
3. Slide underneath the car and loosen the drain plug by turning it counterclockwise with a wrench of the proper size. Be sure that a drain pan is in position to catch the oil as it drains out, then remove the drain plug.
WARNING:
Be very careful when draining the engine oil as it may be hot enough to burn you!
Oil filler
Drain plug
G040A02L
The engine oil and filter should be changed at those intervals specified in the maintenance schedule in Section 5. If the car is being driven in severe conditions, more frequent oil and filter changes are required.
The procedure for changing the oil and filter is as follows:
1. Park the car on level ground and set the parking brake. Start the engine and let it warm up until the needle on the coolant temperature gauge moves above the lowest mark. Turn the engine off and place the gear selector lever in "P".
2. Open the hood and remove the engine oil
filler cap.
4. When the oil has stopped draining, replace the drain plug using a new washer and retighten by turning it clockwise. Oil pan drain plug tightening torque: 3.5 ~ 4.0 kgf.m
5. Remove the oil filter by turning it counterclock- wise with a oil filter wrench of the proper size. A certain amount of oil will come out when you remove the filter. So be sure to have your drain pan in place underneath it. Install a new oil filter in accordance with the instructions on the carton or on the filter itself. Do not over-tighten. Oil filter tightening torque:1.2 ~1.6 kgf.m
6.
Be sure that the mounting surface on the engine is clean and that the old gasket is removed completely. Lubricate the new gasket on the filter with clean engine oil before installation.
7. Remove the engine oil level dipstick.
DO-IT-YOURSELF MAINTENANCE
8. Refill the crankcase with the recommended engine oil. Refer to the specification in chap- ter 9 for engine oil capacity.
CAUTION
Slowly pour the recommended oil using by a tunnel. Do not overfill not to damage engine.
9. Start the engine and check to be sure no oil
is leaking from the drain plug or oil filter.
10.Shut off the engine and recheck the oil level.
NOTE: Always dispose of used engine oil in an environmentally acceptable manner. It is suggested that it be placed in a sealed container and taken to a service station for reclamation. Do not pour the oil on the ground or put it in with the household trash.
PROPOSITION 65 WARNING:
Used engine oil may cause irritation or can- cer of the skin if left in contact with the skin for prolonged periods of time. Used engine oil contains chemicals that have caused cancer in laboratory animals. Always protect your skin by washing your hands thoroughly with soap and warm water as soon as pos- sible after handling used oil.
xgflhma-6.p65
6/16/04, 2:58 PM
6 DO-IT-YOURSELF MAINTENANCE
CHECKING AND CHANGING THE ENGINE COOLANT
G050A01A-AAT
G050B01A-AAT Recommended Engine Coolant
WARNING:
Do not remove the radiator cap when the engine is hot. When the engine is hot, the engine coolant is under pressure and may erupt through the opening if the cap is removed. You could be seriously burned if you do not observe this precaution. Do not remove the radiator cap until the radiator is cool to the touch.
Ambient
Engine Coolant concentration
temperature
°C ( °F) -15 (5) -25 (-13) -35 (-31) -45 (-49)
Antifreeze solution
35% 40% 50% 60%
Water
65% 60% 50% 40%
G050B01L Use a high quality ethylene-glycol coolant in a 50/50 mix with water. The engine coolant should be compatible with aluminum engine parts. Additional corrosion inhibitors or additives should not be used. The cooling system must be maintained with the correct concentration and type of engine coolant to prevent freezing and corrosion. Never allow the concentration of antifreeze to exceed the 60% level or go below the 35% level, or damage to the cooling system may result. For proper concentration when adding or replacing the engine coolant, refer to the following table.
xgflhma-6.p65
6/16/04, 2:58 PM
G050C01A-AAT To Check the Coolant Level
G050D02A-AAT To Change the Engine Coolant The engine coolant should be changed at those intervals specified in the vehicle maintenance schedule in Section 5.
DO-IT-YOURSELF MAINTENANCE
CAUTION:
Engine coolant can damage the finish of your car. If you spill engine coolant on the car, wash it off thoroughly with clean water.
G050C01L The coolant level can be seen on the side of the plastic coolant reservoir. The level of the cool- ant should be between the "L" and "F" lines on the reservoir when the engine is cool. If the level is below the "L" mark, add engine coolant to bring it up between "L" and "F". If the level is low, inspect for coolant leaks and recheck the fluid level frequently. If the level drops again, visit your Hyundai dealer for an inspection and diagnosis of the reason.
1. Park the car on level ground, set the park- ing brake and remove the radiator cap when cool.
2. Be sure your drain receptacle is in place. Open the drain cock on the radiator. Allow all the engine coolant to drain from the cooling system, then securely close the drain cock. 3. Check Section 9 for the capacity of the cooling system in your car. Then, following the manufacturer's directions on the engine coolant container, add the appropriate quan- tity of coolant to the radiator.
G050D01L 4. Turn the radiator cap counterclockwise with- out pressing down on it, until it stops. This relieves any pressure remaining in the cool- ing system. And remove the radiator cap by pushing down and turning counterclock- wise. Now fill the radiator with clean demineralized or distilled water. Continue to add clean demineralized or distilled water in small quan- tities until the fluid level stays up in the radiator neck.
xgflhma-6.p65
6/16/04, 2:58 PM
6 DO-IT-YOURSELF MAINTENANCE
SPARK PLUGS
G060A02Y-AAT (3.5V6)
G060A01L
Your engine was originally equipped with plati- num-tipped spark plugs. Platinum-tipped spark plugs will last longer than conventional type spark plugs and can be identified by blue lines on the ceramic shell.
NOTE: Do not clean or regap platinum-tipped spark plugs.
G050D02L 5. Start the engine, top off the radiator with water and then add coolant to the reservoir until the level is between "LOW" and "FULL". 6. Replace the radiator and reservoir caps and check to be sure the drain cocks are fully closed and not leaking.
WARNING:
The cooling fan is controlled by engine coolant temperature and may sometimes operate even when the engine is not run- ning. Use extreme caution when working near the blades of the coolant fan so that you are not injured by a rotating fan blade. As the engine coolant temperature de- creases, the fan will automatically shut off. This is a normal condition.
G060B04L-AAT Replacing the Spark Plugs
The spark plugs should be changed at the intervals specified in the vehicle maintenance schedule in Section 5 or whenever engine performance indicates they should be changed. Symptoms that suggest poor spark plug perfor- mance include engine misfiring under load, loss of fuel economy, poor acceleration, etc. When spark plugs are replaced, always use spark plugs recommended by Hyundai. The use of other spark plugs can result in loss of perfor- mance, radio interference or engine damage.
Recommended Spark Plugs:
RC10PYP4 (CHAMPION) RC10PYPB4 (CHAMPION) PFR5N-II (NGK)
xgflhma-6.p65
6/16/04, 2:58 PM
NOTE: o Spark plugs should be tightened firmly. Overtightening can damage the threads in the aluminum cylinder head. Also, leaving them too loose can cause the spark plug to get very hot and posibly result in damage to the engine.
o It is recommended that spark plugs be changed by an authorized Hyundai dealer.
WARNING:
It is recommended that the engine be cool or cold when changing the spark plugs. If the engine is hot, you could burn yourself on the insulated connector, the spark plug or the engine itself.
CHANGING THE AIR CLEANER FILTER G070A02Y-AAT
DO-IT-YOURSELF MAINTENANCE
CAUTION:
Operating your vehicle without a proper air cleaner filter in place can result in excessive engine wear. When removing the air cleaner filter, be careful that dust or dirt does not enter the air intake. These may result in damage to the air cleaner filter.
HXG720J The replacement of air cleaner filter is per- formed in the following manner.
1. Unsnap the clips around the cover. 2. When this is done, the cover can be lifted off, the old filter removed and the new filter put in its place.
Genuine Hyundai replacement parts are rec- ommended.
xgflhma-6.p65
6/16/04, 2:58 PM
6 DO-IT-YOURSELF MAINTENANCE
10
WINDSHIELD WIPER BLADES
FILLING THE WASHER RESERVOIR
G080A02A-AAT
G090A01A-AAT
CAUTION:
o Radiator anti-freeze (engine coolant) should not be used in the washer system because it will damage the car's finish. o The washer should not be operated if the washer reservoir is empty. This can dam- age the washer fluid pump.
HXG2007
The washer fluid reservoir supplies fluid to the
windshield washer system.
A good quality washer fluid should be used to fill
the washer reservoir. The fluid level should be
checked more frequently during inclement
weather or whenever the washer system is in
more frequent use.
The capacity of the washer reservoir is 3.2 U.S.
quarts (3.0 Liters).
HEF119
The wiper blades should be carefully inspected from time to time and cleaned to remove accu- mulations of road film or other debris. To clean the wiper blades and arms, use a clean sponge or cloth with a mild soap or detergent and water. If the wipers continue to streak or smear the glass, replace them with genuine Hyundai re- placement parts or their equivalent.
CAUTION:
o Do not operate the wipers on dry glass. This can result in more rapid wear of the wiper blades and may scratch the glass. o Keep the blade rubber out of contact with petroleum products such as engine oil, gasoline, etc.
xgflhma-6.p65
10
6/16/04, 2:58 PM
CHECKING THE TRANSAXLE FLUID G110A01E-AAT Transaxle fluid in the automatic transaxle should be checked at those intervals specified in the vehicle maintenance schedule in Section 5.
NOTE: Basically automatic transaxle fluid is red color. As driving distance increases, the fluid color turns darkish red gradually. It is normal condition and you should not use fluid color as a criterion for replacing the transaxle fluid. You must replace the automatic transaxle fluid in accordance with intervals specified in the vehicle maintenances schedule in section 5.
G110B05A-AAT Recommended Fluid
G110C01L-AAT Transaxle Fluid Capacity
DO-IT-YOURSELF MAINTENANCE
11
Your Hyundai automatic transaxle is specially designed to operate with HYUNDAI GENUINE ATF SP III, DIAMOND ATF SP III, SK ATF SP III or other brands approved by Hyundai Motor Co., Damage caused by a nonspecified fluid is not covered by your new vehicle limited war- ranty.
CAUTION:
Use of aftermarket ATF additives may cause damage to the automatic transaxle. Only use HYUNDAI GENUINE ATF SP III, DIA- MOND ATF SP III, SK ATF SP III or other brands approved by Hyundai Motor Co., If you are having your vehicle serviced at a facility other than a Hyundai dealer, verify ATF is used for your vehicle.
The fluid capacity of the automatic transaxle is 9.1 U.S. quarts.
WARNING:
The transaxle fluid level should be checked when the engine is at normal operating temperature. This means that the engine, radiator, exhaust system etc., are very hot so you should exercise great care not to burn yourself during this procedure.
G110D03L-AAT To Check the Transaxle Fluid Level
HXG065
xgflhma-6.p65
11
6/16/04, 2:58 PM
6 DO-IT-YOURSELF MAINTENANCE
12
Park the car on level ground with the parking brake engaged. When the transaxle fluid level is checked, the transaxle fluid should be at normal operating temperature and the engine idling.
HXG556J
While the engine is idling, apply the brakes and move the gear selector lever from "P" to each of its other positions -- "R", "N", "D" -- and then to "N" with the engine still idling:
1. Open the hood, being careful to keep hands, long hair and clothing clear of any moving parts.
2. Remove the transaxle dipstick, wipe it clean, reinsert the dipstick as far as it will go, then remove it again. Now check the fluid level on the dipstick. It should be in the "HOT" range on the dipstick.
3. Return the gear selector to the "P" position.
CHECKING THE BRAKES
G120A01A-AAT
CAUTION:
Because brakes are essential to the safe operation of the car, it is suggested that they be checked and inspected by your Hyundai dealer. The brakes should be checked and inspected for wear at those intervals specified in the vehicle mainte- nance schedule in Section 5.
Fluid level should be within "HOT" range
4.
G110D03Y If the transaxle fluid level is low, use a funnel to add transaxle fluid through the dipstick tube until the level reaches the "HOT" range. Do not overfill.
WARNING:
The cooling fan is controlled by engine coolant temperature and may sometimes operate even when the engine is not run- ning. Use extreme caution when working