Login- Download PDF Manual
-
See page
418
See page
417
See page
416
See page
339
See page
415
See page
66
CONTINUED
89
10/09/02 13:53:34 31TM8610_095
Multi-Information Display
See page
345
See page
341
See page
342
See page
413
See page
323
See page
70
Canada only
See page
68
See page
128
See page
128
See page
129
See page
369
See page
120
See page
352
See page
353
See page
354
See page
299
See page
80
U.S. only
U.S. only
90
10/09/02 13:53:41 31TM8610_096
Customized Settings
You can customize some vehicle control settings. To enter the customizing mode, press and hold either INFO button ( / ) for more than 3 seconds. To change the settings, the ignition switch must be in the ON (II) position, and the vehicle must be stopped with the transmission in Park.
▲ ▼
If you turn the ignition switch to the ACCESSORY (I) or the LOCK (0) position, or move the shift lever out of Park, the display will change to the normal screen.
If you try to enter the customizing mode while the vehicle is moving, you will see a ‘‘MUST STOP AND SHIFT TO PARK TO CHANGE SETTINGS’’ message and you cannot change the settings.
Multi-Information Display
If you want to change any vehicle control settings, select CHG SETTING, then press the SEL/ RESET button.
Refer to the table on the following pages about the settings you want to customize.
CONTINUED
91
10/09/02 13:53:47 31TM8610_097
Multi-Information Display
Group Setup METER SETUP (P.96)
Menu Item
Description
Setting Option
Page
LANGUAGE SELECTION
Changes the language used in the display.
ADJUST OUTSIDE TEMP. DISPLAY
Changes the outside temperature reading above or below its current reading.
TRIP A RESET with REFUEL ELAPSED TIME RESET
Causes trip meter A and the average fuel economy to reset when you refuel. Resets the elapsed time of your current trip.
DISPLAY KM/MILES
Changes the displayed measurement on the multi- information display.
METER COLOR CHANGE
Turn the ambient meter feature on or off.
＊
＊
ENGLISH FRENCH SPANISH 5°F − 〜 ± (U.S.) 3°C − 〜 ± (Canada) ON OFF IGN OFF TRIP A AUTO KM MILES ON OFF 60 sec 30 sec
＊
＊
＊
＊
0°F
＊
〜
5°F
0°C
＊
〜
3°C
TRIP B
15 sec
97
98
99
100
101
103
105
LIGHTING SETUP (P.104)
INTERIOR LIGHT DIMMING TIME
Changes how long (in seconds) the interior lights stay on after you close the doors.
＊
Default setting
92
10/09/02 13:53:52 31TM8610_098
Group Setup
DOOR SETUP (P.106)
Menu Item AUTO DOOR LOCK
Multi-Information Display
Description
Setting Option
Page
Changes when the doors automatically lock.
AUTO DOOR UNLOCK
Changes when the doors automatically unlock.
DOOR LOCK MODE
KEYLESS LOCK ACKNOWLEDGMENT
SECURITY RELOCK TIMER
Changes which doors unlock with the remote transmitter in a first push. The exterior lights flash each time you press the LOCK or UNLOCK button. A beeper will also sound when you press the LOCK button twice. Changes how long it takes (in seconds) for the doors to relock and the security system to set after you unlock but do not open the door. Set/Cancel all the customized settings as default.
DEFAULT ALL (P.115)
＊
Default setting
＊
DRIVER DOOR / ALL DOORS
＊
＊
SHIFT FROM P WITH VEH SPD OFF SHIFT TO P IGN OFF OFF DRIVER DOOR ALL DOORS ON OFF
＊
＊
90 sec 60 sec 30 sec SET CANCEL
＊
107
108
110
112
113
115
93
10/09/02 13:54:01 31TM8610_099
Multi-Information Display
Customize Settings You can customize some of the vehicle control settings to your preference. Here are the settings you can customize:
METER SETUP LIGHTING SETUP DOOR SETUP
94
When you want to change the vehicle control settings, press the INFO ( / ) button to select CHG SETTING, then press the SEL/ RESET button.
▲ ▼
Each time you press the INFO ( / ▲ ) button, the screen changes as ▼ shown on the next page. Press the INFO ( / ) button until you see the setup you want to customize, then press the SEL/RESET button to enter your selection.
▲ ▼
If you do not make any changes, select ‘‘EXIT.’’ The display returns to the normal display.
You can also use the select/reset knob in the instrument panel. Turn the knob to select a setting and press it to enter your selection.
If you want the settings as they were when the vehicle left the factory, select DEFAULT ALL, as described on page
115
10/09/02 13:54:08 31TM8610_100
Multi-Information Display
NORMAL DISPLAY
U.S.
CANADA
▲ ▼
: Press and hold the INFO ( : Press the SEL/RESET button. : Press the INFO button : Press the INFO button
▼ ▲
) button.
METER SETUP See page 96
LIGHTING SETUP See page 104
DOOR SETUP See page 106
95
10/09/02 13:54:19 31TM8610_101
Multi-Information Display
Meter Setup Here are the four custom settings for the meter setup:
LANGUAGE SELECTION ADJUST OUTSIDE TEMP. DISPLAY TRIP A RESET with REFUEL ELAPSED TIME RESET DISPLAY KM/MILES METER COLOR CHANGE
While ‘‘METER SETUP’’ is shown, press the SEL/RESET button to enter the customize mode.
Each time you press the INFO ( / ▲ ) button, the screen changes as ▼ shown in the illustration. Press the INFO ( / ) button until you see the setting you want to customize, then press the SEL/RESET button to enter your selection.
▲ ▼
96
See page 97 See page 98
See page 99
See page 100
See page 103
See page 101
: Press the SEL/RESET button. : Press the INFO button : Press the INFO button
▼ ▲
10/09/02 13:54:27 31TM8610_102
LanguageSelection
Multi-Information Display
There are three language selections you can make: English, French, and Spanish. To choose the language you want, follow these instructions:
You can choose this item to customize from ‘‘METER SETUP’’ by pressing the INFO ( / ) button repeatedly.
▲ ▼
Press the SEL/RESET button to see the selections.
Select the desired language by pressing the INFO ( / ) button, then enter your selection by pressing the SEL/RESET button.
▲ ▼
When your selection is successfully completed, the display changes as shown above, and then goes back to the customize item screen.
If the ‘‘SETTING INCOMPLETE’’ message appears, go back to ‘‘LANGUAGE SELECTION’’ and repeat the procedure again.
CONTINUED
97
10/09/02 13:54:36 31TM8610_103
Multi-Information Display
AdjustOutsideTemp.Display
U.S. models
Canadian models
U.S. models
Canadian models
If you sometimes find that the temperature reading is a few degrees above or below the actual temperature, you can adjust it by following these instructions:
You can choose this item to customize from ‘‘METER SETUP’’ by pressing the INFO ( / ) button repeatedly. Press the SEL/RESET button to enter the setting.
▲ ▼
98
Adjust the outside temperature value by pressing the INFO ( / ) button repeatedly. Press the SEL/RESET button to set the desired value.
▲ ▼
When your selection is successfully completed, the display changes as shown above, and then goes back to the customize item screen.
If the ‘‘SETTING INCOMPLETE’’ message appears, go back to ‘‘ADJUST OUTSIDE TEMP. DISPLAY’’ and repeat the procedure again.
10/09/02 13:54:46 31TM8610_104
TripAResetWithRefuel
Multi-Information Display
To cause Trip A and average fuel for trip A to reset every time you refuel your vehicle, follow these instructions:
You can choose this item to customize from ‘‘METER SETUP’’ by pressing the INFO ( / ) button repeatedly.
▲ ▼
Press the SEL/RESET button to see the selections.
Select ON or OFF by pressing the INFO ( / ) button, then enter your selection by pressing the SEL/ RESET button.
▲ ▼
When your selection is successfully completed, the display changes as shown above, and then goes back to the customize item screen.
If the ‘‘SETTING INCOMPLETE’’ message appears, go back to ‘‘TRIP A RESET with REFUEL’’ and repeat the procedure again.
CONTINUED
99
10/09/02 13:54:53 31TM8610_105
Multi-Information Display
ElapsedTimeReset There are three elapsed time reset choices you can make:
−
IGN OFF The elapsed time is reset when you turn the ignition switch to the LOCK (0) position.
TRIP A when Trip A is reset.
−
The elapsed time is reset
TRIP B when Trip B is reset.
−
The elapsed time is reset
100
You can choose this item to customize from ‘‘METER SETUP’’ by pressing the INFO ( / ) button repeatedly.
▲ ▼
Press the SEL/RESET button to see the selections.
Select the desired setting by pressing the INFO ( / ) button, then enter your selection by pressing the SEL/RESET button.
▲ ▼
10/09/02 13:55:00 31TM8610_106
Multi-Information Display
If the ‘‘SETTING INCOMPLETE’’ message appears, go back to ‘‘ELAPSED TIME RESET’’ and repeat the procedure again.
DisplayKm/Miles
When your selection is successfully completed, the display changes as shown above, and then goes back to the customize item screen.
To change the displayed measurement in the trip computer and trip information and to switch between kilometers and miles, follow these instructions:
You can choose this item to customize from ‘‘METER SETUP’’ by pressing the INFO ( / ) button repeatedly.
▲ ▼
CONTINUED
101
10/09/02 13:55:06 31TM8610_107
Multi-Information Display
Press the SEL/RESET button to see the selections.
Select AUTO, KM, or MILES by pressing the INFO ( / ) button, then enter your selection by pressing the SEL/RESET button.
▲ ▼
102
AUTO: When you press the km/mile change knob in the instrument panel to switch the speedometer reading between miles per hour (mph) and kilometers per hour (km/h), the displayed measurement in the trip computer and trip information, also switches to kilometers or miles depending on the selected speedometer reading.
KM: The displayed measurement in the trip computer and trip information is set to kilometers.
MILES: The displayed measurement in the trip computer and trip information is set to miles.
When your selection is successfully completed, the display changes as shown above, and then goes back to the customize item screen.
If the ‘‘DISPLAY KM/MILES SETTING INCOMPLETE’’ message appears, go back to ‘‘DISPLAY KM/ MILES’’ and repeat the procedure again.
10/09/02 13:55:14 31TM8610_108
MeterColorChange
You can turn the ambient meter feature on or off (see page ).
72
Press the SEL/RESET button to see the selections.
You can choose this item to customize from ‘‘METER SETUP’’ by pressing the INFO ( / ) button repeatedly.
▲ ▼
Select ON or OFF by pressing the INFO ( / ) button, then enter your selection by pressing the SEL/ RESET button.
▲ ▼
Multi-Information Display
When your selection is successfully completed, the display changes as shown above, and then goes back to the customize item screen.
If the ‘‘METER COLOR CHANGE SETTING INCOMPLETE’’ message appears, go back to ‘‘METER COLOR CHANGE’’ and repeat the procedure again.
103
10/09/02 13:55:21 31TM8610_109
Multi-Information Display
Lighting Setup There is one custom setting for the lighting setup:
INTERIOR LIGHT DIMMING TIME
While ‘‘LIGHTING SETUP’’ is shown, press the SEL/RESET button to enter the customize mode.
Each time you press the INFO ( / ▲ ) button, the screen changes as ▼ shown in the illustration. Press the INFO ( / ) button until you see the setting you want to customize, then press the SEL/RESET button to enter your selection.
▲ ▼
104
See page 105
: Press the SEL/RESET button. : Press the INFO button : Press the INFO button
▼ ▲
10/09/02 13:55:29 31TM8610_110
InteriorLightDimmingTime
Multi-Information Display
The interior lights fade out when you close all doors. To change how long the lights stay on before they fade out, follow these instructions:
You can choose this item to customize from ‘‘LIGHTING SETUP’’ by pressing the INFO ( / ▲ ▼
) button repeatedly.
Press the SEL/RESET button to see the selections.
Select the desired setting (15 sec, 30
sec, or 60 sec) by pressing the INFO ( / ) button, then enter your ▲ ▼ selection by pressing the SEL/ RESET button.When your selection is successfully completed, the display changes as shown above, and then goes back to the customize item screen.
If the ‘‘SETTING INCOMPLETE’’ message appears, go back to ‘‘INTERIOR LIGHT DIMMING TIME’’ and repeat the procedure again.
105
10/09/02 13:55:39 31TM8610_111
Multi-Information Display
Door Setup Here are the five custom settings for the door setup:
AUTO DOOR LOCK AUTO DOOR UNLOCK DOOR LOCK MODE KEYLESS LOCK ACKNOWLEDGMENT SECURITY RELOCK TIMER
While ‘‘DOOR SETUP’’ is shown, press the SEL/RESET button to enter the customize mode.
Each time you press the INFO ( / ▲ ) button, the screen changes as ▼ shown in the illustration. Press the INFO ( / ) button until you see the setting you want to customize, then press the SEL/RESET button to enter your selection.
▲ ▼
106
See page 107
See page 108
See page 110
: Press the SEL/RESET button. : Press the INFO button : Press the INFO button
▼ ▲
See page 113
See page 112
10/09/02 13:55:47 31TM8610_112
AutoDoorLock There are three settings you can choose from:
SHIFT FROM P The doors lock whenever you move the shift lever out of Park.
−
WITH VEHICLE SPEED The doors lock when the vehicle speed reaches about 10 mph (about 16 km/h).
−
−
OFF The auto door lock mode is deactivated all the time.
Multi-Information Display
You can choose this item to customize from ‘‘DOOR SETUP’’ by pressing the INFO ( / ) button repeatedly.
▲ ▼
A/T model is shown.
Press the SEL/RESET button to enter the selecting mode.
Select the desired setting by pressing the INFO ( / ) button, then enter your selection by pressing the SEL/RESET button.
▲ ▼
CONTINUED
107
If the ‘‘SETTING INCOMPLETE’’ message appears, go back to ‘‘AUTO DOOR LOCK’’ and repeat the procedure again.
AutoDoorUnlock There are five possible settings you can choose from:
The driver’s door unlocks when
DRIVER DOOR WITH SHIFT TO P − you move the shift lever to Park with the brake pedal depressed.
ALL DOORS WITH SHIFT TO P − All the doors unlock when you move the shift lever to Park with the brake pedal depressed.
10/09/02 13:55:54 31TM8610_113
Multi-Information Display
When your selection is successfully completed, the display changes as shown above, and then goes back to the customize item screen.
108
10/09/02 13:56:01 31TM8610_114
DRIVER DOOR WITH IGN OFF − The driver’s door unlocks when you turn the ignition switch to the LOCK (0) position.
ALL DOORS WITH IGN OFF All the doors unlock when you turn the ignition switch to the LOCK (0) position.
−
−
OFF deactivated all the time.
The auto door unlock is
Multi-Information Display
You can choose this item to customize from ‘‘DOOR SETUP’’ by pressing the INFO ( / ) button repeatedly.
▲ ▼
Press the SEL/RESET button to enter the selecting mode.
Select the desired setting by pressing the INFO ( / ) button.
▲ ▼
For example, you choose ‘‘DRIVER DOOR with SHIFT to P,’’ you will see the above display.
CONTINUED
109
10/09/02 13:56:09 31TM8610_115
Multi-Information Display
DoorLockMode
If you choose ‘‘ALL DOORS With IGN OFF,’’ you will see the above display.
Press the SEL/RESET button to enter your selection.
When your selection is successfully completed, the display changes as shown above, and then goes back to the customize item screen.
If the ‘‘SETTING INCOMPLETE’’ message appears, go back to ‘‘AUTO DOOR UNLOCK’’ and repeat the procedure again.
To select whether the driver’s door unlocks or all the doors unlock when you unlock the doors with the remote transmitter or the key, follow these instructions.
You can choose this item to customize from ‘‘DOOR SETUP’’ by pressing the INFO ( / ) button repeatedly.
▲ ▼
110
10/09/02 13:56:14 31TM8610_116
Press the SEL/RESET button to enter the selecting mode.
Select the desired setting by pressing the INFO ( / ) button, then enter your selection by pressing the SEL/RESET button.
▲ ▼
When your selection is successfully completed, the display changes as shown above, and then goes back to the customize item screen.
Multi-Information Display
If the ‘‘SETTING INCOMPLETE’’ message appears, go back to ‘‘DOOR LOCK MODE’’ and repeat the procedure again.
111
10/09/02 13:56:20 31TM8610_117
Multi-Information Display
KeylessLockAcknowledgment When you push the LOCK button on the remote transmitter, some exterior lights flash, and a beeper sounds when you push the LOCK button again within 5 seconds to verify that the doors and the hatch are locked and the security system has set (see page customize the exterior lights not to flash and the beeper not to sound.
). You can
267
You can choose this item to customize from ‘‘DOOR SETUP’’ by pressing the INFO ( / ) button repeatedly.
▲ ▼
Press the SEL/RESET button to enter the selecting mode.
Select ON or OFF by pressing the INFO ( / ) button, then enter your selection by pressing the SEL/ RESET button.
▲ ▼
112
10/09/02 13:56:28 31TM8610_118
When your selection is successfully completed, the display changes as shown above, and then goes back to the customize item screen.
If the ‘‘SETTING INCOMPLETE’’ message appears, go back to ‘‘KEYLESS LOCK ACKNOWLEDGMENT’’ and repeat the procedure again.
SecurityRelockTimer If you unlock the doors with the remote transmitter, but do not open any of the doors within 30 seconds, the doors and the hatch, automatically relock, and the security system sets.
You can change this relock time from 30 seconds to 60 or 90 seconds.
Multi-Information Display
You can choose this item to customize from ‘‘DOOR SETUP’’ by pressing the INFO ( / ) button repeatedly.
▲ ▼
CONTINUED
113
10/09/02 13:56:33 31TM8610_119
Multi-Information Display
If the ‘‘SETTING INCOMPLETE’’ message appears, go back to ‘‘SECURITY RELOCK TIMER’’ and repeat the procedure again.
Press the SEL/RESET button to enter the selecting mode.
Select the desired setting by pressing the INFO ( / ) button, then enter your selection by pressing the SEL/RESET button.
▲ ▼
When your selection is successfully completed, the display changes as shown above, and then goes back to the customize item screen.
114
10/09/02 13:56:40 31TM8610_120
DEFAULT ALL
If you want to set the default settings, press the INFO ( / ) button to select DEFAULT ALL, then press the SEL/RESET button.
▲ ▼
To set the default settings, press the INFO ( / ) button to select SET then press the SEL/RESET button.
▲ ▼
If you want to cancel DEFAULT ALL, select CANCEL, then press the SEL/RESET button. The screen goes back to the previous display.
Multi-Information Display
When DEFAULT ALL is set, you will see the above display for several seconds, then the screen returns to the default all setting display.
If the setting is not successfully completed, ‘‘FAILED’’ is shown for several seconds, and then the screen goes back to SET UP. Repeat the same procedure to select DEFAULT ALL.
115
10/09/02 13:56:48 31TM8610_121
Controls Near the Steering Wheel
INSTRUMENT PANEL BRIGHTNESS (P.121)
WINDSHIELD WIPERS/WASHERS (P.117)
HEADLIGHTS/TURN SIGNALS (P.118)
REMOTE AUDIO CONTROL BUTTONS ＊ (P.263)
VEHICLE STABILITY ASSIST (VSA) OFF SWITCH ＊ (P.346)
NAVIGATION SYSTEM VOICE CONTROL BUTTONS ＊ (P.271)
BLUETOOTH HANDS-FREE LINK SYSTEM VOICE CONTROL BUTTONS ＊
(P.271)
HORN ＊
STEERING WHEEL ADJUSTMENTS(P.125)
CRUISE CONTROL BUTTONS MULTI-INFORMATION BUTTONS
＊
(P.268)
＊
(P.76)
NAVIGATION SYSTEM / AUDIO SYSTEM ＊ (P.166)
＊
REAR WINDOW DEFOGGER/ HEATED MIRROR ＊ (P.123/145)
AUXILIARY INPUT JACK ＊ (P.264)
ACCESSORY POWER SOCKET (P.153)
MULTI-INFORMATION BUTTONS (P.76)
＊
EX model with navigation system is shown.
To use the horn, press the center pad of the steering wheel. If equipped Only on vehicles equipped with navigation system. Refer to the navigation system manual.
1 : ＊ 2 : ＊ 3 : ＊ 116
10/09/02 13:56:56 31TM8610_122
Windshield Wipers and Washers
ADJUSTMENT RING
EX model is shown.
1. 2. 3. 4. 5. 6.
MIST OFF INT LO Low speed HI High speed Windshield washers
Intermittent
− − −
Push the right lever up or down to select a position.
MIST The wipers run at high speed until you release the lever.
−
OFF
−
The wipers are not activated.
−
INT The length of the wipe interval is varied automatically according to vehicle’s speed.
EXmodels The length of the wiper interval is varied automatically according to the vehicle’s speed.
Vary the delay by turning the adjustment ring. If you turn it to the shortest delay ( position), the wipers change to low speed operation when the vehicle speed exceeds 12 mph (20 km/h).
LO
−
The wipers run at low speed.
HI
−
The wipers run at high speed.
−
Pull the
Windshield Washer wiper control lever toward you, and hold it. The washers spray until you release the lever. The wipers run at low speed, then complete one more sweep after you release the lever.
117
10/09/02 13:57:07 31TM8610_123
Windshield Wipers and Washers, Turn Signals and Headlights
Rear Window Wiper and Washer
4.
Rotate the switch counterclockwise also to spray the window washer and turn the wiper on.
Turn Signals and Headlights
When you shift the transmission to the reverse position with the front windshield wiper activated, the rear wiper operates automatically even if the rear wiper switch is off.
The rear window washer uses the same fluid reservoir as the wind- shield washer.
1. 2. 3. 4. 5. 6.
Turn Signal OFF Parking and interior lights Headlights on High Beams Flash high beams
1.
2.
3.
OFF When you turn the wiper switch to the ‘‘OFF’’ position, the wiper will return to its parked position. Rotate the switch clockwise to turn the rear window wiper ON. The wiper operates every 7
seconds after completing two sweeps. Hold past ON to activate the rear window wiper a few times and to spray the rear window washer.118
10/09/02 13:57:14 31TM8610_124
−
Turn Signal Push down on the left lever to signal a left turn and up to signal a right turn. To signal a lane change, push lightly on the lever and hold it. The lever will return to the center when you release it or complete a turn.
Turn Signals and Headlights
−
Turning the switch to
’’ position turns on the
Headlights the ‘‘ parking lights, taillights, instrument panel lights, side-marker lights, and rear license plate lights.
−
High Beams Push the left lever forward until you hear a click. The blue high beam indicator will come on (see page to return to the low beams.
). Pull the lever back
69
To flash the high beams, pull the lever back lightly, then release it. The high beams will stay on as long as you hold the lever back.
Turning the switch to the ‘‘ position turns on the headlights.
’’
’’ or ‘‘
When the light switch is in the ‘‘ ’’ position, the lights on indicator comes on as a reminder.
This indicator stays on if you leave the lights on and turn the ignition switch to the ACCESSORY (I) or LOCK (0) position.
If you leave the lights on with the key removed from the ignition switch, you will hear a reminder chime when you open the driver’s door.
119
10/09/02 13:57:19 31TM8610_125
Headlights
position, the high beam
Daytime Running Lights With the headlight switch off or in the headlights and the high beam indicator come on with reduced brightness when you turn the ignition switch to the ON (II) position and release the parking brake. They remain on until you turn the ignition switch off, even if you set the parking brake.
The headlights revert to normal operation when you turn them on with the switch.
120
If you see a ‘‘CHECK DRL SYSTEM’’ message on the multi- information display, there is a problem with the daytime running light system. Take your vehicle to a dealer to have it checked.
10/09/02 13:57:26 31TM8610_126
Instrument Panel Brightness
To reduce glare at night, the instrument panel illumination dims when you turn the light switch to the
or
position. Turning the
knob to the right until you hear a tone will cancel the reduced brightness.
INSTRUMENT PANEL BRIGHTNESS CONTROL KNOB
The knob on the instrument panel controls the brightness of the instrument panel lights. Turn the knob to adjust the brightness with the ignition switch in the ON (II) position and the parking lights on.
BRIGHTNESS LEVEL
When you turn the knob, the multi- information display changes to vertical bars that show you the current level.
You will hear a tone when you reach the maximum or minimum brightness. The brightness level goes out about 5 seconds after you stop adjusting.
The instrument panel will illuminate with reduced brightness when you unlock and open the driver’s door. The brightness will increase slightly when you insert the key in the ignition switch, then go to normal brightness when you turn the ignition switch to the ON (II) position.
CONTINUED
121
10/09/02 13:57:31 31TM8610_127
Instrument Panel Brightness, Hazard Warning Button
Hazard Warning Button
HAZARD WARNING BUTTON
If you do not insert the key in the ignition switch after opening the driver’s door, the illumination turns off about 30 seconds after you close the door.
If you insert the key but do not turn the ignition switch to the ON (II) position, the illumination turns off in about 10 seconds.
Push the button next to the audio system to turn on the hazard warning lights (four-way flashers). This causes all four outside turn signal lights and both turn signal indicators in the instrument panel to flash. Use the hazard warning lights if you need to park in a dangerous area near heavy traffic, or if your vehicle is disabled.
122
10/09/02 13:57:39 31TM8610_128
Rear Window Defogger
The defogger will shut itself off within about 10 to 30 minutes according to the outside temperature (over 32°F, 0°C).
Make sure all rear windows are clear and you have good visibility before starting to drive.
The defogger and antenna wires on the inside of all rear windows can be accidentally damaged. When cleaning the glass, always wipe side- to-side.
U.S. EX model is shown.
The rear window defogger will clear fog, frost, and thin ice from the windows. Push the defogger button to turn it on and off. The indicator in the button comes on to show the defogger is on. It also shuts off when you turn off the ignition switch. You have to turn the defogger on again when you restart the vehicle.
U.S.EXmodelsandallCanadianmodels Pushing this button also turns the mirror heaters on or off. For more information, see page
145
123
10/09/02 13:57:46 31TM8610_129
ECON Button
ECON MODE INDICATOR
ECON BUTTON
MULTI-INFORMATION DISPLAY
Press the ECON button to activate the ECON mode. ECON ON will be displayed on the multi-information display and the ECON mode indicator will illuminate in the instrument panel. Press the ECON button again to turn it off. ECON OFF will appear on the multi- information display.
When you turn off and then restart the engine, the ECON mode setting remains the same as previously set.
The ECON button turns the ECON mode on and off. The ECON mode helps you improve your fuel economy by modifying some vehicle functions. When the ECON mode is on:
124
Engine performance will be different The climate control system will have greater temperature fluctuations
In addition, when the ECON mode is on, you may get more Eco Assist points (see page
316
).
10/09/02 13:57:53 31TM8610_130
Make any steering wheel adjustments before you start driving.
Adjusting the steering wheel position while driving may cause you to lose control of the vehicle and be seriously injured in a crash.
Adjust the steering wheel only when the vehicle is stopped.
To adjust
To lock
LEVER
1.
Pull the lever under the steering column toward you until it stops.
2.
Move the steering wheel so it points toward your chest, not toward your face. Make sure you can see the instrument panel gauges and indicators.
Steering Wheel Adjustments
3.
Push the lever forward fully to lock the steering wheel in position.
Make sure the lever is positioned securely at the bottom of the steering column as shown.
4.
Make sure you have securely locked the steering wheel in place by trying to move it up, down, in, and out.
125
10/09/02 13:58:00 31TM8610_131
Keys and Locks
KEY NUMBER TAG
IGNITION KEYS WITH REMOTE TRANSMITTER
Two ignition keys come with your vehicle. You should keep one of them in a safe place, away from the vehicle, as a spare.
They fit all the locks on your vehicle.
126
You should have received a key number tag with your keys. You will need this number if you ever have to get a lost key replaced. Use only Honda-approved key blanks.
These keys contain electronic circuits that are activated by the immobilizer system. They will not work to start the engine if the circuits are damaged.
Protect the keys from direct sunlight, high temperature, and high humidity.
Do not drop the keys or set heavy objects on them.
Keep the keys away from liquids. If they get wet, dry them immediately with a soft cloth.
10/09/02 13:58:07 31TM8610_132
If the system repeatedly does not recognize the coding of your key, contact your dealer.
Do not attempt to alter this system or add other devices to it. Electrical problems could result that may make your vehicle inoperable.
If you lose your key and you cannot start the engine, contact your dealer.
Always take the ignition key with you whenever you leave the vehicle alone.
The immobilizer system protects your vehicle from theft. If an improperly coded key (or other device) is used, the engine’s fuel system is disabled.
When you turn the ignition switch to the ON (II) position, the immobilizer system indicator should come on briefly, then go off. If the indicator starts to blink, it means the system does not recognize the coding of the key. Turn the ignition switch to the LOCK (0) position, remove the key, reinsert it, and turn the ignition switch to the ON (II) position again.
The system may not recognize your key’s coding if another immobilizer key or other metal object (i.e. key chain) is near the ignition switch when you insert the key.
Immobilizer System
AsrequiredbytheFCC: ThisdevicecomplieswithPart15ofthe FCCrules.Operationissubjecttothe followingtwoconditions:(1)Thisdevice maynotcauseharmfulinterference,and (2)thisdevicemustacceptany interferencereceived,including interferencethatmaycauseundesired operation.
Changesormodificationsnotexpressly approvedbythepartyresponsiblefor compliancecouldvoidtheuser’s authoritytooperatetheequipment.
ThisdevicecomplieswithIndustry CanadaStandardRSS-210. Operationissubjecttothefollowingtwo conditions:(1)thisdevicemaynotcause interference,and(2)thisdevicemust acceptanyinterferencethatmaycause undesiredoperationofthedevice.
127
−
You can insert or
LOCK (0) remove the key only in this position. To turn the key, the shift lever must be in Park, and you must push the key in slightly.
If the front wheels are turned, the anti-theft lock may make it difficult to turn the key. Firmly turn the steering wheel to the left or right as you turn the key.
10/09/02 13:58:14 31TM8610_133
Ignition Switch
The ignition switch has four positions: LOCK (0), ACCESSORY (I), ON (II), and START (III).
128
−
You can
ACCESSORY (I) operate the audio system and the accessory power sockets in this position.
If you leave the key in the ignition switch in the ACCESSORY (I) position and open the driver’s door, you will see a ‘‘RETURN IGNITION SWITCH TO LOCK (0) POSITION’’ message on the multi-information display and hear a reminder beeper.
If you turn the ignition key to the ACCESSORY (I) position with the driver’s door closed, you will see an ‘‘ACCESSORY (I) POSITION’’ message on the multi-information
