2011 Honda CR V Owners Manual

197

10/07/09 18:34:53 31SWA640_203

Playing the AM/FM Radio (EX-L model with navigation system)

Adjusting the Sound

SPEAKER SETTING

−

Adjusts the side-to-

BALANCE side strength of the sound. To adjust the left/right balance, touch the L or R icon.

−

Adjusts the

SUBWOOFER strength of sound from the subwoofer speaker. To adjust the sound strength, touch

or

on each side of the adjustment

bar.

SOUND ICON

You can adjust the sound on the navigation screen. To adjust the sound, push the AUDIO button, then enter the sound grid by touching the SOUND icon on the display.

198

BASS/TREBLE SETTING

BASS

−

Adjusts the bass.

−

Adjusts the treble. To

TREBLE adjust the treble and bass, touch either bass adjustment bar. The adjustment bar on the lower right display shows you the current setting.

on the treble or

or

−

FADER Adjusts the front-to-back strength of the sound. To adjust the front/rear fader, touch the FR or RR icon.

The right upper display shows you the current setting of the sound strength coming from each speaker.

−

The SVC mode

SVC (speed-sensitive volume compensation) controls the volume based on vehicle speed. The faster you go, the louder the audio volume becomes. As you slow down, the audio volume decreases. Touch the appropriate icon (Low, Mid, Hi, Off) to select the mode.

10/07/09 18:35:00 31SWA640_204

Playing the AM/FM Radio (EX-L model with navigation system)

If you feel the sound is too loud, choose low. If you feel the sound is too quiet, choose Hi.

You can also select the icon with the joystick. Move it up and down to move the highlighting and scroll through lists. Select the icon, then move the joystick to left or right to change the setting.

The system will return to the audio display about 5 seconds after you stop adjusting a mode.

ScreenMode You can select the background screen to display the sound level. There are three screen modes: level (the sound level is shown with the vertical bars), spectrum analysis (the sound level appears as ripples of water), and off. Each time you touch the background icon, the display changes.

Audio System Lighting You can use the instrument panel brightness control knob to adjust the illumination of the control panel (see page illuminates when the parking lights are on, even if the radio is turned off.

). The audio system

79

199

10/07/09 18:35:04 31SWA640_205

Playing the XM Radio (EX-L model with navigation system)

XM RADIO ICON MODE ICON

POWER/VOLUME KNOB

AM/FM BUTTON

XM RADIO BUTTON

AUDIO BUTTON

SCAN BUTTON

PRESET CHANNEL NUMBER

200

TUNE BAR

PRESET BUTTONS

JOYSTICK

CATEGORY INDICATOR

10/07/09 18:35:11 31SWA640_206

Playing the XM Radio (EX-L model with navigation system)

Your vehicle is capable of receiving XM Radio anywhere in the United States and Canada, except Hawaii, Alaska, and Puerto Rico. XM is a registered trademark of Sirius XM Radio , Inc. and XM CANADA is a registered business name of Canadian Satellite Radio Inc.

XM Radio receives signals from two satellites to produce clear, high- quality digital reception. It offers many channels in several categories. Along with a large selection of different types of music, XM Radio allows you to view channel and category selections in the display. When you press and hold the AUDIO button, the display also shows all XM information.

Operating the XM Radio To listen to XM Radio, turn the ignition switch to the ACCESSORY (I) or the ON (II) position. Push the power/volume knob to turn on the audio system, and press the CD/XM button. Adjust the volume by turning the knob. The last channel you listened to will show in the display.

You can also change to the XM Radio while you are listening to an FM station, AM station, disc, PC card, etc., by touching the XM1 or XM2 icon on the audio display.

You can also operate the radio using the control buttons on the left side of the screen. The status bar appears on the bottom of the screen each time you press any of the control buttons. On the navigation screen, you can also see the audio information by touching the AUDIO INFO icon on the lower part of the screen.

−

To switch between

MODE channel mode and category mode, touch the MODE icon. In channel mode, you can select all of the available channels. In category mode, such as Jazz, Rock, Classical, etc., you can select all of the channels within that category. Each time you touch and release the MODE icon, the display changes between the channel mode and the category mode.

CONTINUED

201

10/07/09 18:35:21 31SWA640_207

Playing the XM Radio (EX-L model with navigation system)

TUNE Press the TUNE bar to change channel selections. Press

−

for lower numbered

for higher numbered channels ▼

▲ and channels. In the category mode, you can only select channels within that category.

Press and hold

−

CATEGORY either side of the TUNE bar to select another category.

or

) until you hear a beep

On the audio display, you will see the selected CHANNEL (number), CATEGORY, NAME (artist name), and TITLE (music title).

You may experience periods when XM Radio does not transmit the artist’s name and song title information. If this happens, there is nothing wrong with your system.

202

−

The scan function gives

SCAN you a sampling of all channels while in the channel mode. In the category mode, only the channels within that category are scanned. To activate scan, press the SCAN button. The system plays each channel in numerical order for a few seconds, then selects the next channel. When you hear a channel you want to listen to, press the button again.

−

Preset You can store up to 12
preset channels using each preset button or preset icons on the screen. Each preset button or icon stores one channel from the XM1 band and one channel from the XM2 band.

To store a channel:

1.

Press the XM button. Either XM1
or XM2 will show in the display.

2.

Use the tune, seek, or scan function to tune to a desired channel.

In category mode, only channels within that category can be selected. In channel mode, all channels can be selected.

3.

Pick the preset button (icon) you want for that channel. Press and hold the button (icon) until you hear a beep.

10/07/09 18:35:29 31SWA640_208

4.

Repeat steps 2 and 3 to store the first six channels.

5.

Press the XM button again or touch the other XM icon (XM1 or XM2) on the audio display. Store the next six channels using steps 2
and 3.

Once a channel is stored, press and release the proper preset button (icon) to tune to it. Each preset button’s channel is shown on the bottom of the audio display.

Playing the XM Radio (EX-L model with navigation system)

XM Radio Display Messages ‘‘LOADING’’ audio or program information.

XM is loading the

−

−

‘‘OFF AIR’’ currently selected is no longer broadcasting.

The channel

−

The encryption

‘‘UPDATING’’ code is being updated. Wait until the encryption code is fully updated. Channels 0 and 1 should still work normally.

−

The signal is

‘‘NO SIGNAL’’ currently too weak. Move the vehicle to an area away from tall buildings, and with an unobstructed view of the southern horizon.

−

The selected channel

‘‘ - - - - ’’ number does not exist or is not part of your subscription.

‘‘NO INFO’’ This channel has no artist or title information at this time.

−

‘‘ANTENNA’’ There is a problem with the XM antenna. Please consult your dealer.

−

CONTINUED

203

10/07/09 18:35:36 31SWA640_209

Playing the XM Radio (EX-L model with navigation system)

Signal may be blocked by mountains or large obstacles to the south.

Signal weaker in these areas.

SATELLITE

204

GROUND REPEATER

The XM satellites are in orbit over the equator; therefore, objects south of the vehicle may cause satellite reception interruptions. To help compensate for this, ground-based repeaters are placed in major metropolitan areas.

Satellite signals are more likely to be blocked by tall buildings and mountains the farther north you travel from the equator. Carrying large items on a roof rack can also block the signal.

Depending on where you drive, you may experience reception problems. Interference can be caused by any of these conditions:

Driving on the north side of an east/west mountain road. Driving on the north side of a large commercial truck on an east/west road.

10/07/09 18:35:44 31SWA640_210

Driving in tunnels. Driving on a road beside a vertical wall, steep cliff, or hill to the south of you. Driving on the lower level of a multi-tiered road. Driving on a single lane road alongside dense trees taller than 50 ft. (15 m) to the south of you. Large items carried on a roof rack.

There may be other geographic situations that could affect XM Radio reception.

AsrequiredbytheFCC: Changesormodificationsnotexpressly approvedbythepartyresponsiblefor compliancecouldvoidtheuser’s authoritytooperatetheequipment.

Playing the XM Radio (EX-L model with navigation system)

Receiving XM Radio Service If your XM Radio service has expired or you purchased your vehicle from a previous owner, you can listen to a sampling of the broadcasts available on XM Radio. With the ignition switch in the ACCESSORY (I) or ON (II) position, push the power/volume knob to turn on the audio system and press the CD/XM button. A variety of music types and styles will play.

, or at

If you decide to purchase XM Radio service, contact XM Radio at www.xmradio.com 1-800-852-9696. In Canada, contact XM CANADA at www.xmradio.ca at 1-877-209-0079. You will need to give them your radio I.D. number and your credit card number. To get your radio I.D. number, press the TUNE bar until ‘‘0’’ appears in the display. Your I.D. will appear in the display.

, or

After you’ve registered with XM Radio, keep your audio system in the XM radio mode while you wait for activation. This should take about 30
minutes.

While waiting for activation, make sure your vehicle remains in an open area with good reception. Once your audio system is activated, you’ll be able to listen to XM Radio broadcasts. XM Radio will continue to send an activation signal to your vehicle for at least 12 hours from the activation request. If the service has not been activated after 36 hours, contact XM Radio. In Canada, contact XM CANADA .

205

10/07/09 18:35:49 31SWA640_211

Playing a Disc (EX-L model with navigation system)

CD ICON

JOYSTICK

RANDOM BUTTON

FAST FORWARD BUTTON

SKIP

＋

BUTTON

REPEAT BUTTON

REWIND BUTTON

SKIP

−

BUTTON

POWER/VOLUME KNOB

OPEN BUTTON

CD BUTTON

AUDIO BUTTON

SCAN BUTTON

TUNE BAR

206

10/07/09 18:35:57 31SWA640_212

To Play a Disc (In-dash single player) You operate the in-dash disc player with the same controls used for the radio. To load or play discs, the ignition switch must be in the ACCESSORY (I) or ON (II) position.

Your vehicle also has a CD changer that operates with the same functions as the in-dash disc player (see page

215

).

Do not use discs with adhesive labels. The label can curl up and cause the disc to jam in the unit.

Playing a Disc (EX-L model with navigation system)

NOTE: If a file on an MP3 or WMA disc is protected by digital rights management (DRM), the audio unit displays CD FORMAT, and then skips to the next file.

This audio system can also play CD-Rs and CD-RWs compressed in MP3 or WMA formats. When playing a disc in MP3, you will see ‘‘MP3’’ on the screen. In WMA format, ‘‘WMA’’ will appear on the screen. You can select up to 255
folders and play up to 999 tracks. If the disc has a complex structure, it takes a while to read the disc before the system begins to play it.

Video CDs and DVDs do not work in this unit.

Depending on the software the files were made with, it may not be possible to play some files, or display some text data.

CONTINUED

207

10/07/09 18:36:04 31SWA640_213

Playing a Disc (EX-L model with navigation system)

ToLoadaDisc

DISC SLOT

OPEN BUTTON The in-dash disc player is behind the navigation screen. To use the disc player, press the OPEN button beside the screen. The screen folds back, and the disc slot appears.

Insert a disc about halfway into the disc slot. The drive will pull the disc in the rest of the way and begin to play it.

You cannot load and play 3-inch (8-cm) discs in this system.

CLOSE BUTTON To return the screen to the upright position, press the CLOSE button on the edge of the screen panel. Do not use the folded down screen as a tray. If you put a cup, for example, on the screen, the liquid inside the cup may spill on the screen when you go over a bump.

208

10/07/12 17:05:39 31SWA640_214

Push the AUDIO button beside the screen to show the audio display and operate the disc player.

You can also operate the audio system without using the control icons on the audio screen. Press the CD button. The status bar appears on the bottom of the screen. On the navigation screen, you can see the audio information whenever you touch the AUDIO INFO icon on the lower portion of the screen.

When playing a CD recorded with text data, the track, album, and artist name are shown on the audio display. When playing a disc in MP3 or WMA, the folder number and name, the file number and name, the artist name, and the elapsed time are shown. The system will continuously play a disc until you change modes. If the disc was not recorded with text data, it will not be displayed.

Playing a Disc (EX-L model with navigation system)

ToChangeorSelectTracks/Files

PRESET BUTTON’S FUNCTION

You can also select an icon with the joystick. Move it to left, right, up, or down to change the highlighting and scroll through lists. Then press ENT on the top of the joystick to select the icon.

PRESET BUTTONS

You can use the preset buttons while a disc is playing to select passages and change tracks (files in MP3 or WMA mode). Each preset button’s function is shown on the bottom of the screen.

−

Each time you press and (preset 6 button), the

SKIP release player skips forward to the beginning of the next track (file in MP3 or WMA mode). Press and release (preset 5 button), to skip backward to the beginning of the current track. Press it again to skip to the beginning of the previous track.

FF/REW a track/file, press and hold

To move rapidly within

−

(preset 4 button) or (preset 3 button).

CONTINUED

209

10/07/09 18:36:20 31SWA640_215

Playing a Disc (EX-L model with navigation system)

−

To

InMP3orWMAmode FOLDER SELECTION select a different folder, press either side of the TUNE bar to move to the beginning of the next folder. Press the side of the TUNE bar to skip to the next folder, and the side to move to the beginning of the current folder. Press it again to skip to the beginning of the previous folder.

▼

▲

−

TRACK REPEAT (FILE REPEAT) To continuously replay a track (file in MP3 or WMA mode), press and release the RPT button (preset 1 button). You will see TRACK REPEAT in the display. Press the RPT button again to turn it off.

210

−

This

InMP3orWMAmode FOLDER RANDOM feature, when activated, plays all files in the selected folder in random order, rather than in the order they are compressed. To activate folder random, press and hold the RDM button. You will see FOLDER RANDOM in the display. The system then selects and plays files randomly. This continues until you deactivate folder random by pressing the RDM button again, or if you select a different folder with the TUNE bar.

−

This feature,

InMP3orWMAmode FOLDER REPEAT when activated, replays all files on the selected folder in the order they are compressed. To activate folder repeat, press and hold the RPT button (preset 1 button) for 2
seconds. You will see FOLDER REPEAT in the display. The system continuously replays the current folder. Press the RPT button again to turn it off. Selecting a different folder with the TUNE bar also turns off folder repeat.

−

TRACK RANDOM (Random within a disc/folder) This feature plays the tracks/files within a disc in random order. To activate track random, press and release the RDM button (preset 2 button). You will see TRACK RANDOM in the display. Press the RDM button again to return to normal play.

10/07/09 18:36:28 31SWA640_216

Playing a Disc (EX-L model with navigation system)

−

SCAN (TRACK/FILE SCAN) The scan function samples all tracks (files in MP3 or WMA) in the order they were recorded. To activate scan, press and release the SCAN button. You will see TRACK SCAN in the display. You will get a 10 second sampling of each track/file on the disc. Press the SCAN button to get out of scan mode and play the last track/file sampled.

Pressing either SKIP button (preset 5 button or 6 button) also turns off scan.

This feature,

InMP3orWMAmode FOLDER SCAN − when activated, samples the first file in each folder on the disc in order. To activate folder scan, press and hold the SCAN button for 2 seconds. You will see FOLDER SCAN in the display.

The system plays the first file in each folder for about 10 seconds. If you do nothing, the system then plays the first file in each folder for 10 seconds each. After playing the first file of the last folder, the system goes to normal play.

Pressing either SKIP button (preset 5 or 6), or selecting a different folder with the TUNE bar, or pressing the SCAN button, also turns off folder scan.

UsingaTrackList

FOLDER ICON

RETURN ICON

You can also select a track/file directly from the folder and file lists on the audio display. Press the AUDIO button to show the audio display.

Touch the Track List icon to switch the display to the folder list, then select and touch a desired folder.

CONTINUED

211

10/07/09 18:36:37 31SWA640_217

Playing a Disc (EX-L model with navigation system)

FOLDER ICON

TRACK/FILE ICON

RETURN ICON

The display changes to the file list. Then, select and touch a desired file.

Touch the folder icon on the upper left of the screen to move to the parent folder.

or

▲ ▼

To scroll through the display, touch the icon on the side of the screen. To go back to the previous display, touch the Return icon on the screen.

212

To select a desired icon with the joystick, move it in the appropriate direction, then press ENT.

Press the AUDIO button to go back to the normal audio playing display. Pressing the CANCEL button goes back to the previous screen, and pressing the MAP button cancels the audio control display on the screen.

When playing a CD recorded with text data, each track name is shown on the audio display. With a disc recorded in MP3 or WMA, the folder number and the location are also displayed.

If the disc was not recorded with text data, only the track number is shown.

To Stop Playing a Disc To play the radio when a disc is playing, press the AM/FM button or touch the FM1, FM2, AM, XM1, or XM2 icon. If a PC card is in the audio unit, touch the CARD icon to play the PC card. If a CD or CDs are loaded in the CD changer, touch the CDC icon to play the CD changer. Press the CD button again or touch the CD icon to switch back to the disc player.

You can also press the MODE button on the steering wheel to change modes.

If you turn the system off while a disc is playing, either with the power/volume knob or by turning off the ignition switch, the disc will stay in the drive. When you turn the system back on, the disc will begin playing where it left off.

10/07/09 18:36:43 31SWA640_218

206

RemovingaDisc To remove a disc from the audio unit, fold back the screen by pressing the ). Press OPEN button (see page the disc eject button ( ) to remove the disc. If you eject the disc, but do not remove it from the slot, the system will automatically reload it after 10 seconds and put it in pause mode. To begin playing, press the CD/XM button.

To return the screen to the upright position, press the CLOSE button.

You cannot close the screen if a disc is partially inserted into its slot.

You can also eject the disc when the ignition switch is off.

Playing a Disc (EX-L model with navigation system)

Protecting Discs For information on how to handle and protect discs, see page

252

213

10/07/09 18:36:49 31SWA640_219

Disc Player Error Messages (EX-L model with navigation system)

Error Message

Cause

Solution

DISC ERROR

FOCUS Error

MECH ERROR

Mechanical Error

CHECK DISC

TOC Error

HEAT ERROR

High Temperature

Press the eject button, and pull out the disc. Check if it is inserted correctly in the disc player. Make sure the disc is not scratched or damaged. For more information see page 253 . Press the eject button, and pull out the disc. Check the disc for damage or deformation. For more information see page 253 . If the disc cannot be pulled out, or the error message does not disappear after the disc is ejected, see your dealer. Press the eject button, and pull out the disc. Check the disc for damage or deformation. Will disappear when the temperature returns to normal.

The chart on the right explains the error messages you may see in the display while playing a disc. If you see an error message in the display while playing a disc, press the eject button. After ejecting the disc, check it for damage or deformation. If there is no damage, insert the disc again. For additional information on damaged discs, see page 253

The audio system will try to play the disc. If there is still a problem, the error message will reappear. Press the eject button, and pull out the disc. Insert a different disc. If the new disc plays, there is a problem with the first disc. If the error message cycle repeats and you cannot clear it, take your vehicle to a dealer.

214

10/07/09 18:36:53 31SWA640_220

CD Changer (EX-L model with navigation system)

POWER/VOLUME KNOB

CD ICON

CD CHANGER ICON

OPEN BUTTON

CD BUTTON AUDIO BUTTON

SCAN BUTTON

TUNE BAR

JOYSTICK

REPEAT BUTTON

BUTTON

SKIP ＋ BUTTON

SKIP

−

RANDOM BUTTON

FAST FORWARD BUTTON

REWIND BUTTON

215

10/07/09 18:37:00 31SWA640_221

CD Changer (EX-L model with navigation system)

Loading CDs in the Changer Your vehicle has the CD changer in the center console.

CD-R, CD-RW discs, and CDs compressed in MP3 and WMA will not work in this unit. Video CDs and DVD discs also will not work.

Do not spill any liquids on the center console. Spilled liquids can damage electrical components in the CD changer.

216

1.

Open the center console cover, then slide open the CD changer cover by pulling it rearward.

2.

Push the EJECT button to remove the CD magazine. The magazine will pop up automatically.

EJECT BUTTON

10/07/09 18:37:06 31SWA640_222

3.

To install a CD into the magazine, push the button while pulling out on the tab.

CD Changer (EX-L model with navigation system)

4.

Put a CD on the tray with the printed surface facing up as shown.

5.

Reinstall the tray in the magazine. Repeat this procedure to open the other five trays.

6.

Store all six trays in the magazine, and reinstall the magazine in the CD changer as shown.

7.

Make sure to slide the CD changer cover closed until it clicks.

To remove CDs from the CD changer, refer to the loading procedure.

217

10/07/09 18:37:13 31SWA640_223

CD Changer (EX-L model with navigation system)

To select a different disc, use the preset buttons (5 or 6). Press and release the Preset 5 (DISC ) − button to select the previous disc or Preset 6 (DISC ) to select the next disc in sequence. Pressing the or side of the TUNE bar also ▼ changes the disc. If you select an empty position in the CD changer, the system will try to load the CD in the next available slot.

＋

▲

TUNE BAR

PRESET BUTTONS

You can use the preset buttons while a disc is playing to select passages and change tracks. Each preset button function is shown on the bottom of the screen.

To Play a CD To play CDs, the ignition switch must be in the ACCESSORY (I) or ON (II) position.

You operate the CD changer with the same controls used for the in- dash disc player or the radio. To select the CD changer, touch the CDC icon. The disc and track numbers are displayed. The system will continuously play a CD until you change modes.

Do not use CDs with adhesive labels. The label can curl up and cause the CD to jam in the unit.

218

10/07/09 18:37:21 31SWA640_224

CD Changer (EX-L model with navigation system)

−

button

Push the

SKIP (preset 6) to play the next track on the disc. Push the (preset 5) once to replay the track in play; press it twice to replay the previous track.

button

−

To move more rapidly

FF/REW within a track, press and hold the (preset 3)

(preset 4) or

button.

−

To REPEAT (Track Repeat) continuously replay a track, press and release the RPT button (preset 1). You will see TRACK REPEAT in the display. Press the RPT button again to turn it off.

−

To continuously

DISC REPEAT replay the current CD, press and hold the RPT button (preset 1) until you see the DISC REPEAT in the display. Press it again to turn it off.

−

RANDOM (Track Random) Press and release the RDM button (preset 2) to play the tracks in random order. You will see TRACK RANDOM in the display. Press the RDM button again to return to normal play.

−

Press and hold the

DISC SCAN SCAN button to get a 10 second sampling of the first song of each disc in the CD changer. You will see DISC SCAN in the display. Press and hold the button again to turn it off.

−

To play all

DISC RANDOM tracks in each CD in random order, press and hold the RDM button (preset 2) until you see DISC RANDOM in the display. Press the RDM button again to return to normal play.

−

The SCAN

SCAN (Track Scan) function samples all the tracks on the selected disc in the order they are recorded. To activate it, press and release the SCAN button. You will see TRACK SCAN in the display, and you will get a 10 second sampling of each track on the selected CD. Press the SCAN button again to get out of scan mode.

219

10/07/09 18:37:26 31SWA640_225

CD Changer (EX-L model with navigation system)

To Stop Playing a CD To play the radio when a disc is playing, press the AM/FM button or the CD/XM button. Touch the USB icon to switch to an appropriate audio unit (if it is connected to the USB adapter cable).

If you turn the system off while a CD in the CD changer is playing, the CD will stay in the drive. When you turn the system back on, the CD will be in pause mode. Touch the CDC icon on the audio screen. The CD will begin playing where it left off.

If there is a PC card in the audio unit, touch the CARD icon to switch to the PC card while a CD is playing.

Touch the CDC icon again to play the CD in the CD changer.

You can also press the MODE button on the steering wheel to change modes.

220

10/07/09 18:37:33 31SWA640_226

CD Changer Error Messages (EX-L model with navigation system)

Error Message

Cause

Solution

DISC ERROR

FOCUS Error

MECH ERROR

Mechanical Error

The disc is pulled out. Check if it is inserted correctly in the disc player. Make sure the disc is not scratched or damaged. For more information see page 253. Press the eject button, and pull out the disc. Check the disc for damage or deformation. For more information see page 253. If the disc cannot be pulled out, or the error message does not disappear after the disc is ejected, see your dealer.

The chart on the right explains the error messages you may see in the display while playing a disc. If you see an error message in the display while playing a disc, press the eject button. After ejecting the disc, check it for damage or deformation. If there is no damage, insert the disc again. For additional information on damaged discs, see page 253

The audio system will try to play the disc. If there is still a problem, the error message will reappear. Press the eject button, and pull out the disc. Insert a different disc. If the new disc plays, there is a problem with the first disc. If the error message cycle repeats and you cannot clear it, take your vehicle to a dealer.

221

10/07/09 18:37:38 31SWA640_227

Playing a PC card (EX-L model with navigation system)

TRACK LIST ICON

POWER/VOLUME KNOB

PC CARD ICON

JOYSTICK

PLAY MODE ICON

OPEN BUTTON

CD/XM BUTTON

AUDIO BUTTON SCAN BUTTON

TUNE BAR

222

REPEAT BUTTON

SKIP ＋ BUTTON

SKIP

−

BUTTON

RANDOM BUTTON

FAST FORWARD BUTTON

REWIND BUTTON

10/07/09 18:37:48 31SWA640_228

Playing a PC card (EX-L model with navigation system)

To Play a PC Card You operate the PC card player with the same controls used for the radio and the disc player. To load or play a card, the ignition switch must be in the ACCESSORY (I) or ON (II) position.

The PC card player reads and plays cards in MP3 or WMA formats. Depending on the format, the screen will indicate ‘‘MP3’’ or ‘‘WMA’’ when a card is playing. The card limit of the player is 255 folders and 999
tracks. If the card has a complex structure, it takes some time for the system to begin playing it.

Based on PCMCIA 2.1/JEIDA 4.2, the recommended PC cards for the PC card reader are:

CompactFlash Flash ATA SD memory card

Always use the recommended memory card with the appropriate adapter (if an adapter is needed). Some memory cards will not work in this unit.

NOTE:

When you insert a PC card into the slot, make sure you put it in straight. If you cannot insert it, remove it, and insert again.

Do not keep PC cards in the vehicle. Direct sunlight and high heat will damage them.

To avoid damaging the card reader, do not insert hard disc drive cards into the PC card slot.

You cannot close the screen (move it to the upright position) until the PC card is inserted all the way into its slot or removed.

Never insert foreign objects into the PC card slot.

CONTINUED

223

10/07/09 18:37:55 31SWA640_229

Playing a PC card (EX-L model with navigation system)

LoadingaPCCard

PC CARD SLOT

Depending on the software the files were made with, it may not be possible to play some files, or display some text data.

In WMA format, DRM (digital rights management) files cannot be played. If the system finds a DRM file, it skips that file and plays the next available folder or file.

The PC card slot is behind the navigation screen. To use the PC card player, press the OPEN button beside the screen. The screen folds back, and the PC card slot appears.

Insert a PC card straight into the slot. The drive will read the PC card and begin to play it.

Return the screen to the upright position by pressing the CLOSE button on the edge of the screen panel.

Push the AUDIO button beside the screen to show the audio display and operate the PC card player.

You can also operate the audio system without using the control icons on the audio screen. Press any of the appropriate control buttons. The status bar appears on the bottom of the screen. On the navigation screen, you can see the audio information whenever you touch the AUDIO INFO icon on the screen.

224

10/07/09 18:38:05 31SWA640_230

There are three play modes: Folder, Artist, and Album. Touch the PLAY MODE icon, then choose one of the modes by touching its icon. When a mode is selected, it is highlighted in blue.

Folder mode plays tracks in the order they were added to the card.

Artist mode plays tracks in alphabetical order, by artist and song title.

Album mode plays albums (folders) in alphabetical order.

If play mode information was not included in the tracks/files when they were added to the card, it will not be displayed on the screen.

Playing a PC card (EX-L model with navigation system)

ToSelectaPlayMode

FOLDER MODE

PLAY MODE ICON

MODE INDICATOR

ARTIST MODE

PLAY MODE ICON

ALBUM MODE

PLAY MODE ICON

MODE INDICATOR

MODE INDICATOR

CONTINUED

225

10/07/09 18:38:11 31SWA640_231

Playing a PC card (EX-L model with navigation system)

PLAY MODE ICON

To select a play mode, push the AUDIO button to show the audio display, then touch the PLAY MODE icon on the display.

Select the desired mode by touching the appropriate icon, or move the joystick, then press ENT.

After you select the play mode, the display changes to the selectable playing menu. If you select ‘‘Continue playing the current song,’’ the system goes into the selected play mode after playing the current file.

226

10/07/09 18:38:18 31SWA640_232

If you select ‘‘Play a new track list,’’ the system goes into the selected play mode immediately and begins to play the new track list.

To go back to the previous screen, press the CANCEL button on the right side of the screen. To exit the play mode screens, press the AUDIO button.

Playing a PC card (EX-L model with navigation system)

ToChangeorSelectTracks/Files

PRESET BUTTON’S FUNCTION

Icons on the screen can also be selected with the joystick. Move the joystick left or right and up or down until the icon is highlighted, then press ENT on the top of the joystick to select the icon.

PRESET BUTTONS

You can use the preset buttons while a card is playing to select or change files. Each preset button’s function is shown on the bottom of the screen.

CONTINUED

227

10/07/12 17:05:45 31SWA640_233

Playing a PC card (EX-L model with navigation system)

−

Each time you press and (preset 6 button), the

SKIP release player skips forward to the beginning of the next file. Press and release (preset 5 button), to skip backward to the beginning of the current file. Press it again to skip to the beginning of the previous file.

−

FF/REW a file, press and hold button) or

To move rapidly within (preset 4

(preset 3 button).

−

▲

To

FOLDER SELECTION select a different folder, press either side of the TUNE bar to move to the beginning of the next folder. Press side of the TUNE bar to skip the the next folder, and press the side ▼ to move to the beginning of the current folder. Press it again to skip to the beginning of the previous folder.

228

−

To continuously replay

TRACK REPEAT (FILE REPEAT) a file, press and release the RPT button (preset 1). You will see TRACK REPEAT in the display. Press the RPT button again to turn it off.

−

This feature, when

FOLDER/ARTIST/ALBUM REPEAT activated, replays all the files on the selected folder/artist/album in the order they are recorded or listed. To activate each repeat mode, press and hold the RPT button (preset 1
button) for 2 seconds. You will see FOLDER REPEAT, ARTIST REPEAT or ALBUM REPEAT in the display. The system continuously replays the current folder/artist/ album. Press and hold the RPT button again to turn it off. Pressing the RDM button, or selecting a different folder/artist/album with the TUNE bar also turns off the repeat feature.

−

TRACK RANDOM (Random within a folder) This feature plays the files within a folder in random order. To activate random play, press and release the RDM button (preset 2 button). You will see TRACK RANDOM in the display. Press the RDM button again to return to normal play.

−

This feature, when

FOLDER/ARTIST/ALBUM RANDOM activated, plays all files in each folder/artist/album in random order, rather than in the order they are recorded or listed. To activate each random play, push and hold the RDM button (preset 2) for 2 seconds. You will see FOLDER RANDOM, ARTIST RANDOM or ALBUM RANDOM in the display.

10/07/09 18:38:32 31SWA640_234

The system then selects and plays files randomly. This continues until you deactivate each random play by pressing the RDM button again.

−

The SCAN function

SCAN samples all the files on the PC card in the order they are recorded. To activate the scan feature, press and release the SCAN button. You will see TRACK SCAN in the display. You will get a 10 second sampling of each file on the PC card. Press the SCAN button again to get out of scan mode and play the last file sampled.

Pressing either of the SKIP buttons (preset 5 button or 6 button) also turns off the scan feature.

Playing a PC card (EX-L model with navigation system)

−

This feature, when

FOLDER/ARTIST/ALBUM SCAN activated, samples the first file in each folder/artist/album on the PC card in order. To activate each scan feature, press and hold the SCAN button. You will see FOLDER SCAN, ARTIST SCAN or ALBUM SCAN in the display.

The system plays the first file in the folder for about 10 seconds. If you do nothing, the system plays the first file in each folder, in order, for 10
seconds each. After playing the first file of the last folder/artist/album, the system returns to normal play.

Pressing either of the SKIP buttons (preset 5 button or 6 button), selecting a different folder/artist/ album with the TUNE bar, or pressing the SCAN button, also turns off the scan feature.

UsingaTrackList

TRACK LIST ICON

You can also select a file directly from the folder and track lists on the audio display. Press the AUDIO button to show the audio display, then touch the Track List icon. The folder list menu appears on the display.

CONTINUED

229

10/07/09 18:38:39 31SWA640_235

Playing a PC card (EX-L model with navigation system)

FOLDER ICON

ARTIST NAME

RETURN ICON

or

▲ ▼

To scroll through the display, touch the icon on the side of the screen. To go back to the previous display, touch the Return icon.

To select a folder, touch its icon on the screen. The display changes to the file list. Then, select and touch a desired file. In folder mode, touch the folder icon on the upper left of the screen to move to the parent folder.

In artist mode, the artist name is also displayed on the right side of each selectable icon. Select the desired file.

230

10/07/09 18:38:48 31SWA640_236

Playing a PC card (EX-L model with navigation system)

ALBUM NAME

Press the AUDIO button to go back to the normal audio playing display. Pressing the CANCEL button goes back to the previous screen, and pressing the MAP button cancels the audio control display on the screen.

SongSearchFunction

SONG SEARCH ICON

In album mode, the album name is also displayed on the right side of each selectable icon. Select the desired file.

To select a desired icon with the joystick, move it in the appropriate direction, then press ENT.

Folder mode is shown.

RETURN ICON

When you select ‘‘Song Search’’ from the track list display, the song search menu appears.

TITLE BY KEYWORD ICON

ARTIST ICON

ALBUM ICON

You can then select any of three modes to search a file: Title by Keyword, Artist, and Album.

CONTINUED

231

10/07/09 18:38:56 31SWA640_237

Playing a PC card (EX-L model with navigation system)

SearchingforaSongTitlebyKeyword

MORE ICON

To cancel the selected letter, touch the Delete icon. To select more characters, touch the More icon. The other character list will be shown.

FILE LIST

SearchingforaSongbyArtistName

ARTIST LIST

DELETE ICON

LIST ICON

In Title by Keyword mode, enter the title name, or any keyword, by touching the letter icons on the screen. Press the List icon to begin the song search. If you press the CANCEL button on the control panel, the display returns to the mode menu without doing a search.

232

After the system searches for a song, a file list is displayed. To scroll through the list, touch the or icon on the side of the screen. Select the desired file by touching the appropriate icon, or moving the joystick and pressing ENT.

▲ ▼

Select the Artist icon, and the artist list appears. Select the desired artist, and the artist’s file list is displayed.

10/07/09 18:39:06 31SWA640_238

SearchingforaSongbyAlbumName

ALBUM LIST

Select the Album icon, and the album list appears. Select the desired album, and its song list is displayed. You can then select the desired song from the list.

Playing a PC card (EX-L model with navigation system)

To Stop Playing a PC Card To play the radio when a PC card is playing, press the AM/FM button or touch the FM1, FM2, AM, XM1, or XM2 icon. If a disc is in the audio unit, press the CD/XM button or touch the CD icon to play the disc. If a CD or CDs are in the CD changer, touch the CDC icon to play the disc(s). Touch the CARD icon to switch back to the PC card player.

You can also press the MODE button on the steering wheel to change modes.

If you turn the system off while a PC card is playing, either with the power/volume knob or by turning off the ignition switch, the card will stay in the drive. When you turn the system back on, the card will begin playing where it left off.

When you leave the vehicle, always remove the PC card from the audio unit.

RemovingaPCCard To remove a PC card from the audio unit, fold back the screen by pressing the OPEN button (see page 222
to remove the card. If you do not remove it from the slot, you cannot return the screen to the upright position.

). Press the eject button (

To return the screen to the upright position, press the CLOSE button.

You can also eject a card when the ignition switch is off.

PC Card Player Malfunction If there is a problem with the PC card player, see your dealer.

233

10/07/09 18:39:10 31SWA640_239

PC card Error Messages (EX-L model with navigation system)

If you see an error message in the display while playing a PC card, find the solution in the chart to the right. If you cannot clear the error message, take your vehicle to your dealer.

Error Message

Solution

FILE ERROR

NO MUSIC

MEDIA ERROR

The system cannot read the file(s). Check the files on the disc. There is a possibility that the files have been damaged. It appears when the PC card is empty or there are no MP3 or WMA files in the PC card. Save the MP3 or WMA files in the PC card. It appears when an unsupported PC card is inserted. The system supports CF card, Flash ATA card, and SanDisk 6-in-1 Card Adapter.

234

10/07/09 18:39:15 31SWA640_240

Playing an iPod (EX-L model with navigation system)

POWER/VOLUME KNOB

USB ICON

iPod INDICATOR

OPEN BUTTON

CD/XM BUTTON

AUDIO BUTTON

JOYSTICK

REPEAT BUTTON

BUTTON

SKIP ＋ BUTTON

SKIP

−

RANDOM BUTTON

FAST FORWARD BUTTON

REWIND BUTTON

235

10/07/09 18:39:24 31SWA640_241

Playing an iPod (EX-L model with navigation system)

To Play an iPod This audio system can select and play the audio files on the iPod with the same controls used for the in- dash disc player. To play an iPod, connect it to the USB adapter cable in the upper glove box by using your dock connector. Press the AUDIO button beside the screen to show the audio display and touch the USB icon. The ignition switch must be in the ACCESSORY (I) or ON (II) position. The iPod will also be recharged with the ignition switch in these positions.

The audio system reads and plays playable sound files on the iPod. The system cannot operate an iPod as a mass storage device. The system will only play songs stored on the iPod with iTunes.

iPod and iTunes are registered trademarks owned by Apple Inc.

iPods compatible with your audio system using the USB adapter cable are:

Model iPod classic (80/160 G) iPod classic (120 G) iPod with video (iPod 5th generation) iPod nano iPod nano 2nd generation iPod nano 3rd generation iPod nano 4th generation iPod nano 5th generation iPod touch iPod touch 2nd generation

Software

Ver. 1.1.2 or more

Ver. 2.0.1 or more

Ver. 1.3.0 or more

Ver. 1.3.1 or more Ver. 1.1.3 or more

Ver. 1.1.3 or more

Ver. 1.0.3 or more

Ver. 1.0.1 or more

Ver. 1.1.5 or more Ver. 2.2.1 or more

236

Use only compatible iPods with the latest software. iPods that are not compatible will not work in this audio unit.

NOTE:

Do not connect your iPod using a hub.

Do not keep the iPod in the vehicle. Direct sunlight and high heat will damage it.

Do not use an extension cable between the USB adapter cable equipped with your vehicle and your dock connector.

We recommend backing up your data before playing it.

Some devices cannot be powered or charged via the USB adapter. If this is the case, use the accessory adapter to supply power to your device.

10/07/09 18:39:34 31SWA640_242

Playing an iPod (EX-L model with navigation system)

ConnectinganiPod

RELEASE BUTTON

USB ADAPTER CABLE

DOCK CONNECTOR

USB CONNECTOR

4.

Install the dock connector to the USB adapter cable securely.

1.

Open the upper glove box.

2.

Push the release button to release the USB adapter cable.

3.

Connect your dock connector to the iPod correctly and securely.

If the audio system still does not recognize the iPod, the iPod may need to be reset. Follow the instructions that came with your iPod, or you can find reset instructions online at itunes/