2010 Honda Civic Coupe Owners Manual

speed and prevent your brakes from overheating while going down a steep hill. Before downshifting, make sure the engine speed will not go into the tachometer’s red zone in the lower gear.

Rapid slowing or speeding up can cause loss of control on slippery surfaces. If you crash, you can be injured.

Use extra care when driving on slippery surfaces.

OnSimodel Your vehicle is equipped with an aluminum shift lever. If you leave the vehicle parked outside for a long

272

time on a hot day, be careful before moving the shift lever. Because of the heat, the shift lever may be extremely hot. If the outside temperature is low, the shift lever feels cold.

Recommended Shift Points Drive in the highest gear that lets the engine run and accelerate smoothly. This will give you good fuel economy and effective emissions control. The following shift points are recommended:

Onmodelswith5-speedmanual transmission

Shift up

Normal acceleration

1st to 2nd 2nd to 3rd 3rd to 4th 4th to 5th

15 mph (24 km/h) 27 mph (44 km/h) 39 mph (63 km/h) 53 mph (85 km/h)

Onmodelswith6-speedmanual transmission

Shift up

Normal acceleration

1st to 2nd 2nd to 3rd 3rd to 4th 4th to 5th 5th to 6th

17 mph (27 km/h) 29 mph (46 km/h) 37 mph (60 km/h) 43 mph (69 km/h) 49 mph (79 km/h)

09/07/07 14:34:58 31SVA640_278

Engine Speed Limiter If you exceed the maximum speed for the gear you are in, the engine speed will enter into the tachometer’s red zone. If this occurs, you may feel the engine cut in and out. This is caused by a limiter in the engine’s computer controls. The engine will run normally when you reduce the rpm below the red zone.

Before downshifting, make sure the engine will not go into the tachometer’s red zone.

Reverse Lockout 6-speedmanualtransmission The manual transmission has a lockout so you cannot accidentally shift from any forward gear to reverse while the vehicle is moving at a certain speed. If you cannot shift to reverse when the vehicle is stopped, do the following:

OnSimodel Your vehicle has a rev limit indicator to show you when the engine speed is near the tachometer’s red zone (see page

61

).

Manual Transmission

2.

If you are still unable to shift to reverse, apply the parking brake, and turn the ignition key to the ACCESSORY (I) or LOCK (0) position.

3.

Press the clutch pedal, and shift to reverse.

4.

With the clutch pedal still pressed, start the engine.

If you need to use this procedure to shift to reverse, your vehicle may be developing a problem. Have the vehicle checked by your dealer.

Move the shift lever in sequence. With the clutch pedal pressed, 1. move the shift lever to the first/ second gear side of the neutral gate, then shift to reverse.

273

09/07/07 14:35:07 31SVA640_279

Automatic Transmission

Shift Lever Position Indicators

These indicators on the instrument panel show which position the shift lever is in.

274

The ‘‘D’’ indicator comes on for a few seconds when you turn the ignition switch to the ON (II) position. If it flashes while driving (in any shift position), it indicates a possible problem in the transmission.

If the malfunction indicator lamp comes on along with the ‘‘D’’ indicator, there is a problem with the automatic transmission control system. Avoid rapid acceleration, and have the transmission checked by your dealer as soon as possible.

Shifting

SHIFT LEVER

RELEASE BUTTON

To shift from Park to any position, press firmly on the brake pedal, and press the release button on the front of the shift lever, then move the lever. You cannot shift out of Park when the ignition switch is in the LOCK (0) or ACCESSORY (I) position.

09/07/07 14:35:17 31SVA640_280

Automatic Transmission

Do this:

Press the brake pedal, and press the shift lever release button.

Press the shift lever release button.

Move the shift lever.

If you have done all of the above and still cannot move the lever out of Park, see on page 277

Shift Lock Release

To avoid transmission damage, come to a complete stop before shifting into Park. You must also press the release button to shift into Park. The shift lever must be in Park before you can remove the key from the ignition switch.

To shift from:

P to R

R to P N to R D to 2
2 to 1
1 to 2
2 to D D to D D to N D to D N to D R to N

−

Press the brake

Reverse (R) pedal and the release button on the front of the shift lever to shift from Park to reverse. To shift from reverse to neutral, come to a complete stop, and then shift. Press the release button before shifting into reverse from neutral.

−

This position mechani-

Park (P) cally locks the transmission. Use Park whenever you are turning off or starting the engine. To shift out of Park, you must press on the brake pedal and have your foot off the accelerator pedal. Press the release button on the front of the shift lever to move it.

−

Use neutral if you

Neutral (N) need to restart a stalled engine, or if it is necessary to stop briefly with the engine idling. Shift to the Park position if you need to leave your vehicle for any reason. Press on the brake pedal when you are moving the shift lever from neutral to another gear.

−

Use this position for

Drive (D) your normal driving. The transmission automatically selects a suitable gear (1 through 5) for your speed and acceleration. You may notice the transmission shifting up at higher engine speeds when the engine is cold. This helps the engine warm up faster.

CONTINUED

275

−

First (1) To shift from second to first, press the release button on the front of the shift lever. This position locks the transmission in first gear. By upshifting and downshifting through 1, 2, D , and D, you can operate the transmission much like a manual transmission without a clutch pedal.

Engine Speed Limiter If you exceed the maximum speed for the gear you are in, the engine speed will enter into the tachometer’s red zone. If this occurs, you may feel the engine cut in and out. This is caused by a limiter in the engine’s computer controls. The engine will run normally when you reduce the rpm below the red zone.

09/07/07 14:35:25 31SVA640_281

Automatic Transmission

−

This position is similar

Drive (D ) to D, except only the first three gears are selected. Use D to provide engine braking when going down a steep hill. D can also keep the transmission from cycling between third and fourth gears in stop-and-go driving.

−

To shift to second,

Second (2) press the release button on the front of the shift lever. This position locks the transmission in second gear. It does not downshift to first gear when you come to a stop.

Use second gear:

For more power when climbing. To increase engine braking when going down steep hills. For starting out on a slippery surface or in deep snow. To help reduce wheel spin.

276

09/07/07 14:35:37 31SVA640_282

Shift Lock Release Do this if pushing on the brake pedal and pressing the release button does not let you shift the transmission out of Park:

1.

Set the parking brake.

2.

Remove the key from the ignition switch.

COVER

screwdriver or metal fingernail file, carefully pry on the edge of the cover to remove it.

6.

RELEASE BUTTON

Automatic Transmission

Remove the key from the shift lock release slot, then install the cover. Make sure the notch on the cover is on the rear. Return the key to the ignition switch, press the brake pedal, and restart the engine.

If you need to use the shift lock release, it means your vehicle is developing a problem. Have it checked by your dealer.

SHIFT LOCK RELEASE SLOT

4.

Insert the key in the shift lock release slot.

5.

Push down on the key while you press the release button on the front of the shift lever and move the shift lever out of Park to neutral.

3.

Put a cloth on the edge of the shift lock release slot cover to prevent scratches. Using a small flat-tip

277

09/07/07 14:35:50 31SVA640_283

Parking

Always use the parking brake when you park your vehicle. Make sure the parking brake is set firmly, or your vehicle may roll if it is parked on an incline.

If your vehicle has an automatic transmission, set the parking brake before you put the transmission in Park. This keeps the vehicle from moving and putting pressure on the parking mechanism in the transmission.

278

Parking Tips

Make sure the moonroof (if equipped) and the windows are closed.

Turn off the lights.

Place any packages, valuables, etc., in the trunk or take them with you.

Lock the doors.

Onvehicleswithsecuritysystem Check the indicator on the instrument panel to verify that the security system is set.

Never park over dry leaves, tall grass, or other flammable materials. The hot three way catalytic converter could cause these materials to catch on fire.

If the vehicle is facing uphill, turn the front wheels away from the curb. If your vehicle has a manual transmission, put it in first gear.

If the vehicle is facing downhill, turn the front wheels toward the curb. If your vehicle has a manual transmission, put it in reverse gear.

Make sure the parking brake is fully released before driving away. Driving with the parking brake partially set can overheat or damage the rear brakes.

Never install a sunshade between the upper and lower meters on the instrument panel. If you do, you could cause heat damage to the upper meter on a very hot day.

09/07/07 14:36:01 31SVA640_284

Constant application of the brakes when going down a long hill builds up heat and reduces their effective- ness. Use the engine to assist the brakes by taking your foot off the accelerator and downshifting to a lower gear.

Check the brakes after driving through deep water. Apply the brakes moderately to see if they feel normal. If not, apply them gently and frequently until they do. Be extra cautious in your driving.

Your vehicle is equipped with front disc brakes. The brakes on the rear wheels may be disc or drum, depending on the model. A power assist helps reduce the effort needed on the brake pedal. The anti-lock brake system (ABS) helps you retain steering control when braking very hard.

On vehicles with vehicle stability assist (VSA) system, the emergency brake assist system increases the stopping force when you depress the brake pedal hard in an emergency situation.

Resting your foot on the pedal keeps the brakes applied lightly, builds up heat, reduces their effectiveness and reduces brake pad life. In addition, fuel economy can be reduced. It also keeps your brake lights on all the time, confusing drivers behind you.

Braking System

Braking System Design The hydraulic system that operates the brakes has two separate circuits. Each circuit works diagonally across the vehicle (the left-front brake is connected with the right-rear brake, etc.). If one circuit should develop a problem, you will still have braking at two wheels.

Brake Pad Wear Indicators If the brake pads need replacing, you will hear a distinctive, metallic screeching sound when you apply the brake pedal. If you do not have the brake pads replaced, they will screech all the time. It is normal for the brakes to occasionally squeal or squeak when you apply them.

279

You will feel a pulsation in the brake pedal when the ABS activates, and you may hear some noise. This is normal: it is the ABS rapidly pumping the brakes. On dry pavement, you will need to press on the brake pedal very hard before the ABS activates. However, you may feel the ABS activate immediately if you are trying to stop on snow or ice.

09/07/07 14:36:09 31SVA640_285

Anti-lock Brakes (ABS)

The anti-lock brake system (ABS) helps prevent the wheels from locking up, and helps you retain steering control by pumping the brakes rapidly, much faster than a person can do it.

The electronic brake distribution (EBD) system, which is part of the ABS, also balances the front-to-rear braking distribution according to vehicle loading.

Youshouldneverpumpthebrakepedal. Let the ABS work for you by always keeping firm, steady pressure on the brake pedal. This is sometimes referred to as ‘‘stomp and steer.’’

280

ABS Indicator

If this indicator comes on, the anti- lock function of the braking system has shut down. The brakes still work like a conventional system, but without anti-lock. You should have your dealer inspect your vehicle as soon as possible.

If the indicator comes on while driving, test the brakes as instructed on page

351

09/07/07 14:36:19 31SVA640_286

If the ABS indicator and the brake system indicator come on together, and the parking brake is fully released, the EBD system may also be shut down.

Important Safety Reminders ABS does not reduce the time or distance it takes to stop the vehicle. It only helps with the steering control during braking.

A vehicle with ABS may require a longer distance to stop on loose or uneven surfaces, such as gravel or snow, than a vehicle without anti- lock.

Anti-lock Brakes (ABS)

351

. If the brakes feel normal,

Test your brakes as instructed on page drive slowly and have your vehicle repaired by your dealer as soon as possible. Avoid sudden hard braking which could cause the rear wheels to lock up and possibly lead to a loss of control.

OnvehicleswithVSAsystem The VSA indicator will come on along with the ABS indicator.

ABS will not prevent a skid that results from changing direction abruptly, such as trying to take a corner too fast or making a sudden lane change. Always drive at a safe speed for the road and weather conditions.

ABS cannot prevent a loss of stability. Always steer moderately when you are braking hard. Severe or sharp steering wheel movement can still cause your vehicle to veer into oncoming traffic or off the road.

281

09/07/07 14:36:32 31SVA640_287

Vehicle Stability Assist (VSA ), aka Electronic Stability Control (ESC), System

EX-LandSimodels The vehicle stability assist (VSA) system helps to stabilize the vehicle during cornering if the vehicle turns more or less than desired. It also assists you in maintaining traction while accelerating on loose or slippery road surfaces. It does this by regulating the engine’s output and by selectively applying the brakes.

When VSA activates, you may notice that the engine does not respond to the accelerator in the same way it does at other times. There may also be some noise from the VSA hydraulic system. You will also see the VSA activation indicator blink.

282

The VSA system cannot enhance the vehicle’s driving stability in all situations and does not control your vehicle’s entire braking system. It is still your responsibility to drive and corner at reasonable speeds and to leave a sufficient margin of safety.

VSA Activation Indicator

When VSA activates, you will see the VSA Activation indicator blinks.

Vehicle Stability Assist (VSA) System Indicator

If this indicator comes on while driving, pull to the side of the road when it is safe, and turn off the engine. Reset the system by restarting the engine. If the VSA system indicator stays on or comes back on while driving, have the VSA system inspected by your dealer.

If the indicator does not come on when the ignition switch is turned to

the ON (II) position, there may be a problem with the VSA system. Have your dealer inspect your vehicle as soon as possible.

The main function of the

NOTE: VSA system is generally known as Electronic Stability Control (ESC). The system also includes a traction control function.

Without VSA, your vehicle will have normal braking and cornering ability, but it will not have VSA traction and stability enhancement.

U.S.models If the low tire pressure indicator or TPMS indicator comes on, the VSA system automatically turns on even if the VSA system is turned off by pressing the VSA OFF switch (see page cannot turn the VSA system off by pressing the VSA OFF switch again.

). If this happens, you

283

09/07/07 14:36:43 31SVA640_288

Vehicle Stability Assist (VSA ), aka Electronic Stability Control (ESC), System

VSA OFF Switch

This switch is under the driver’s side vent. To turn the VSA system on and off, press and hold it until you hear a beep.

When VSA is off, the VSA activation indicator comes on as a reminder. Press and hold the switch again. It turns the system back on.

VSA is turned on every time you start the engine, even if you turned it off the last time you drove the vehicle.

In certain unusual conditions when your vehicle gets stuck in shallow mud or fresh snow, it may be easier to free it with the VSA temporarily switched off. When the VSA system is off, the traction control system is also off. You should only attempt to free your vehicle with the VSA off if you are not able to free it when the VSA is on.

Immediately after freeing your vehicle, be sure to switch the VSA on again. We do not recommend driving your vehicle with the VSA and traction control systems switched off.

VSA and Tire Sizes Driving with varying tire or wheel sizes may cause the VSA to malfunction. When replacing tires, make sure they are of the same size and type as your original tires (see page

330

).

If you install winter tires, make sure they are the same size as those that were originally supplied with your vehicle. Exercise the same caution during winter driving as you would if your vehicle was not equipped with VSA.

283

09/07/07 14:36:53 31SVA640_289

Tire Pressure Monitoring System (TPMS)

U.S.modelsonly Your vehicle is equipped with a tire pressure monitoring system (TPMS) that turns on every time you start the engine and monitors the pressure in your tires while driving.

Each tire has its own pressure sensor (not including the spare tire). If the air pressure of a tire becomes significantly low while driving, the sensor in that tire immediately sends a signal that causes the low tire pressure indicator to come on.

284

Low Tire Pressure Indicator

When the low tire pressure indicator is on, one or more of your tires is significantly underinflated. You should stop and check your tires as soon as possible, and inflate them to the proper pressure as indicated on the vehicle’s tire information placard.

If you think you can safely drive a short distance to a service station, proceed slowly, and inflate the tire to the recommended pressure shown on the driver’s doorjamb.

If the tire is flat, or if the tire pressure is too low to continue driving, replace the tire with the compact spare tire (see page 339

).

If you cannot make the low tire pressure indicator go out after inflating the tires to the specified values, have your dealer check the system as soon as possible.

Driving on a significantly under inflated tire causes the tire to overheat and can lead to tire failure. Underinflation also reduces fuel efficiency and tire tread life, and may affect the vehicle’s handling and stopping ability.

Because tire pressure varies by temperature and other conditions, the low tire pressure indicator may come on unexpectedly.

09/07/07 14:37:05 31SVA640_290

For example, if you check and fill your tires in a warm area, then drive in extremely cold weather, the tire pressure will be lower than measured and could be underinflated and cause the low tire pressure indicator to come on. Or, if you check and adjust your tire pressure in cooler conditions, and drive into extremely hot conditions, the tire may become overinflated. However, the low tire pressure indicator will not come on if the tires are overinflated.

Refer to page guidelines.

323

for tire inflation

Although your tire pressure is monitored, you must manually check the tire pressures monthly.

Each tire, including the spare, should be checked monthly when cold, and set to the recommended inflation pressure as specified on the tire

Tire Pressure Monitoring System (TPMS)

information label and in the owner’s manual (see page

325

).

Tire Pressure Monitoring System (TPMS) Indicator This indicator comes on and stays on if there is a problem with the tire pressure monitoring system.

If this happens, the system will shut off and no longer monitor tire pressures. Have the system checked by your dealer as soon as possible.

OnvehicleswithVSAsystem If the low tire pressure indicator or TPMS indicator comes on, the VSA system automatically turns on even if the VSA system is turned off by pressing the VSA OFF switch (see page cannot turn the VSA system off by pressing the VSA OFF switch again.

). If this happens, you

283

When you restart the vehicle with the compact spare tire, the TPMS indicator may also come on and stay on after driving several miles (kilometers).

285

09/07/07 14:37:14 31SVA640_291

Tire Pressure Monitoring System (TPMS)

The low tire pressure indicator or the TPMS indicator will go off, after several miles (kilometers) driving, when you replace the spare tire with the specified regular tire equipped with the tire pressure monitor sensor.

Never use a puncture-repairing agent in a flat tire. If used, you will have to replace the tire pressure sensor. Have the flat tire repaired by your dealer as soon as possible.

AsrequiredbytheFCC: ThisdevicecomplieswithPart15ofthe FCCrules.Operationissubjecttothe followingtwoconditions:(1)Thisdevice maynotcauseharmfulinterference,and (2)thisdevicemustacceptany interferencereceived,including interferencethatmaycauseundesired operation.

Changesormodificationsnotexpressly approvedbythepartyresponsiblefor compliancecouldvoidtheuser’s authoritytooperatetheequipment.

ThisdevicecomplieswithIndustry CanadaStandardRSS-210. Operationissubjecttothefollowingtwo conditions:(1)thisdevicemaynotcause interference,and(2)thisdevicemust acceptanyinterferencethatmaycause undesiredoperationofthedevice.

Changing a Tire with TPMS If you have a flat tire, the low tire pressure indicator will come on. Replace the flat tire with the compact spare tire (see page

339

).

Each wheel (except the compact spare tire wheel) is equipped with a tire pressure sensor mounted inside the tire behind the valve stem. You must use TPMS specific wheels. It is recommended that you always have your tires serviced by your dealer or qualified technician.

After you replace the flat tire with the compact spare tire, the low tire pressure indicator stays on. This is normal; the system is not monitoring the spare tire pressure. Manually check the spare tire pressure to be sure it is correct. After several miles (kilometers) driving with the compact spare tire, the TPMS indicator comes on and the low tire pressure indicator goes off.

286

09/07/07 14:37:19 31SVA640_292

Your vehicle is not designed to tow a trailer. Attempting to do so can void your warranties.

Towing Your Vehicle Your vehicle is not designed to be towed behind a motor home. If your vehicle needs to be towed in an emergency, see page

358

Towing a Trailer

287

09/07/07 14:37:21 31SVA640_293

288

09/07/07 14:37:27 31SVA640_294

Maintenance

This section explains why it is important to keep your vehicle well maintained and how to follow basic maintenance safety precautions.

This section also includes instructions on how to read the maintenance minder messages on the information display, and instructions for simple maintenance tasks you may want to take care of yourself.

If you have the skills and tools to perform more complex maintenance tasks on your vehicle, you may want to purchase the service manual. See page for information on how to obtain a copy, or see your dealer.

383

Maintenance Safety Maintenance Minder Fluid Locations Adding Engine Oil

...................... .................... .............................. ........................ ....... .............................. ................

. 290
. 291
. 298
. 300
. 300
. 301
. 301

Recommended Engine Oil Synthetic Oil Engine Oil Additives

Changing the Engine Oil and

Filter

. 302
Engine Coolant . 304
Windshield Washers . 307
Automatic Transmission Fluid . 308
. 309
Manual Transmission Fluid . 310
Brake and Clutch Fluid . 311
Power Steering Fluid Lights . 312
. 319
Cleaning the Seat Belts . 320
Floor Mats . 321
Dust and Pollen Filter Wiper Blades . 321
. 323
Tires . 333
Checking the Battery Vehicle Storage . 335

........................................... .............................. .................... .... ........ ................ .................... ............................................. ................ ..................................... .................. ................................. ............................................... ................... .............................

289

09/07/07 14:37:40 31SVA640_295

Maintenance Safety

All service items not detailed in this section should be performed by a certified technician or other qualified mechanic.

Important Safety Precautions To eliminate potential hazards, read the instructions before you begin, and make sure you have the tools and skills required.

Make sure your vehicle is parked on level ground, the parking brake is set, and the engine is off.

To clean parts, use a commercially available degreaser or parts cleaner, not gasoline.

To reduce the possibility of fire or explosion, keep cigarettes, sparks, and flames away from the battery and all fuel-related parts.

Wear eye protection and protective clothing when working with the battery or compressed air.

290

Improperly maintaining this vehicle, or failing to correct a problem before driving can cause a crash in which you can be seriously hurt or killed.

Always follow the inspection and maintenance recommendations and schedules in this owner’s manual.

Injury from moving parts. not run the engine unless instructed to do so.

Do

Failure to properly follow maintenance instructions and precautions can cause you to be seriously hurt or killed.

Always follow the procedures and precautions in this owner’s manual.

Potential Vehicle Hazards

Carbon Monoxide poison from engine exhaust. Be sure there is adequate ventilation whenever you operate the engine.

Burns from hot parts. Let the engine and exhaust system cool down before touching any parts.

Some of the most important safety precautions are given here. However, we cannot warn you of every conceivable hazard that can arise in performing maintenance. Only you can decide whether or not you should perform a given task.

09/07/07 14:37:49 31SVA640_296

Your vehicle displays engine oil life and maintenance service items on the information display to show you when you should have your dealer perform engine oil replacement and indicated maintenance service.

Based on the engine operating conditions and accumulated engine revolutions, the onboard computer in your vehicle calculates the remaining engine oil life and displays it as a percentage.

Engine Oil Life Indicator

INFORMATION DISPLAY

Maintenance Minder

The remaining engine oil life is displayed on the information display according to this table:

Calculated Engine

Displayed

MAINTENANCE MINDER INDICATOR

ENGINE OIL LIFE INDICATOR

To see the current engine oil life, turn the ignition switch to the ON (II) position, then push and release the SEL/RESET button repeatedly until the engine oil life indicator appears (see page

65

).

Oil Life (%) 91 % 81 % 71 % 61 % 51 % 41 % 31 % 21 % 16 % 11 % 6 % 6 % 1 %

100 % 90 % 80 % 70 % 60 % 50 % 40 % 30 % 20 % 15 % 10 % 15 % 5 %

− − − − − − − − − − − − − 0 %

＊

＊

Engine Oil Life (%)

100 % 90 % 80 % 70 % 60 % 50 % 40 % 30 % 20 % 15 % 10 % 15 % 5 % 0 %

＊

＊ ＊

1 : 2 :

DX and Canadian DX-G LX, EX, EX-L, and Si

CONTINUED

291

09/07/07 14:37:56 31SVA640_297

Maintenance Minder

MAINTENANCE ITEM CODE(S)

ENGINE OIL LIFE INDICATOR

If the remaining engine oil life is 15
to 6 percent, you will see the engine oil life indicator every time you turn the ignition switch to the ON (II) position. The maintenance minder indicator will also come on, and the maintenance item code(s) for other scheduled maintenance items needing service will be displayed next to the engine oil life indicator.

292

The 15 and 10 percent oil life indicators remind you that your vehicle will soon be due for scheduled maintenance.

SERVICE MESSAGE

When the remaining engine oil life is 5 to 1 percent, you will see a ‘‘SERVICE’’ message along with the same maintenance item code(s), every time you turn the ignition switch to the ON (II) position.

09/07/07 14:38:07 31SVA640_298

Maintenance Minder

The maintenance item code or codes indicate the main and sub items required at the time of the oil change (see page

297

).

You can switch the display to the odometer, the trip meter, and the outside temperature indicator (if equipped) by pushing the SEL/ RESET button on the dashboard repeatedly.

When the engine oil life is 15 to 1
percent, the maintenance minder indicator ( ) comes on every time you turn the ignition switch to the ON (II) position, then it goes out if you switch the information display.

When you see this message, have the indicated maintenance performed by your dealer as soon as possible.

NEGATIVE DISTANCE TRAVELED

When the remaining engine oil life is 0 percent, the engine oil life indicator will blink. The display comes on every time you turn the ignition switch to the ON (II) position. The maintenance minder indicator on in the instrument panel. When you see this message, immediately have the indicated maintenance done by your dealer.

) also comes on and remains

If you do not perform the indicated maintenance, negative distance traveled is displayed and begins to blink after the vehicle has been driven 10 miles (10 km) or more.

Negative distance traveled means your vehicle has passed the maintenance required point. Immediately have the indicated maintenance done by your dealer.

CONTINUED

293

09/07/07 14:38:19 31SVA640_299

Maintenance Minder

You can change the information display from the engine oil life display to the odometer, the trip meter, or the outside temperature (if equipped) every time you press and release the SEL/RESET button.

When the engine oil life is 0 percent or negative distance traveled, the maintenance minder indicator ) remains on even if you change the information display.

Immediately have the service performed, and make sure to reset the display as described as follows.

294

Maintenance Main Items and Sub Items

MAINTENANCE MAIN ITEM

MAINTENANCE SUB ITEM

All maintenance items displayed on the information display are in code. For an explanation of these maintenance codes, see page

297

Resetting the Engine Oil Life Display Your dealer will reset the display after completing the required maintenance service. You will see ‘‘OIL LIFE 100%’’ on the information display the next time you turn the ignition switch to the ON (II) position.

If maintenance service is done by someone other than your dealer, reset the maintenance minder as follows:

1.

Turn the ignition switch to the ON (II) position.

2.

Press the SEL/RESET button repeatedly until the engine oil life indicator is displayed.

09/07/07 14:38:28 31SVA640_300

3.

Press the SEL/RESET button for about 10 seconds. The engine oil life and the maintenance item code(s) will blink.

4.

Press the SEL/RESET button for more than 5 seconds. The maintenance item code(s) will disappear, and the engine oil life will reset to ‘‘100.’’

Maintenance Minder

Important Maintenance Precautions If you have the required service done but do not reset the display, or reset the display without doing the service, the system will not show the correct maintenance intervals. This can lead to serious mechanical problems because you will no longer have an accurate record of when maintenance is needed.

Your authorized Honda dealer knows your vehicle best and can provide competent, efficient service.

CONTINUED

295

09/07/07 14:38:41 31SVA640_301

Maintenance Minder

However, service at a dealer is not mandatory to keep your warranties in effect. Maintenance may be done by any qualified service facility or person who is skilled in this type of automotive service. Make sure to have the service facility or person reset the display as previously described. Keep all receipts as proof of completion, and have the person who does the work fill out your Honda Service History or Canadian Maintenance Log. Check your warranty booklet for more information.

We recommend using Honda parts and fluids whenever you have maintenance done. These are manufactured to the same high quality standards as the original components, so you can be confident of their performance and durability.

296

Maintenance,

U.S. Vehicles: replacement, or repair of emissions control devices and systems may be done by any automotive repair establishment or individual using parts that are ‘‘certified’’ to EPA standards.

＃

According to state and federal regulations, failure to perform maintenance on the items marked with will not void your emissions warranties. However, all maintenance services should be performed in accordance with the intervals indicated by the information display.

Owner’s Maintenance Checks You should check the following items at the specified intervals. If you are unsure of how to perform any check, turn to the appropriate page listed.

Engine oil level time you fill the fuel tank. See page

Check every

255

−

Engine coolant level radiator reserve tank every time you fill the fuel tank. See page

Check the

−

257

Automatic transmission Check the fluid level monthly. See page 308

−

Brakes monthly. See page

−

Check the fluid level

310

−

Tires Check the tire pressure monthly. Examine the tread for wear and foreign objects. See page 323

−

Check the operation of

Lights the headlights, parking lights, taillights, high-mount brake light, and license plate lights monthly. See page

312

09/07/07 14:38:50 31SVA640_302

Maintenance Minder

Symbol

Maintenance Main Items

Replace engine oil ＊ Replace engine oil and oil filter ＊ Inspect front and rear brakes Check parking brake adjustment Visually inspect these items:

Tie rod ends, steering gear box, and boots Suspension components Driveshaft boots Brake hoses and line (including ABS/VSA) All fluid levels and condition of fluids Exhaust system ＃ Fuel lines and connections ＃

If the message ‘‘SERVICE’’ does not appear more than 12 months after the display is reset, change the engine oil every year.

See information on maintenance and emissions warranty in the center column on page

296

＊

＃

NOTE:

Symbol

Maintenance Sub Items

Rotate tires Replace air cleaner element

If you drive in dusty conditions, replace every 15,000
miles (24,000 km).

Replace dust and pollen filter

If you drive primarily in urban areas that have high concentrations of soot in the air from industry and from diesel-powered vehicles, replace every 15,000
miles (24,000 km).

Inspect drive belt Replace transmission fluid Replace spark plugs Inspect valve clearance Replace engine coolant

Independent of the maintenance minder indicator in the information display, replace the brake fluid every 3 years. Inspect idle speed every 160,000 miles (256,000 km). Adjust the valves during services A, B, 1, 2, or 3 only if they are noisy.

297

09/07/07 14:38:55 31SVA640_303

Fluid Locations

DX, Canadian DX-G, LX, EX, and EX-L models

ENGINE OIL FILL CAP

ENGINE OIL DIPSTICK (Orange handle)

BRAKE FLUID (Black cap)

POWER STEERING FLUID ＊ (Red cap)

WASHER FLUID (Blue cap)

CLUTCH FLUID (Manual transmission only) (Light gray cap)

AUTOMATIC TRANSMISSION FLUID DIPSTICK (Yellow loop)

ENGINE COOLANT RESERVOIR

＊

: Except for Canadian DX-G with manual transmission

298

RADIATOR CAP

09/07/07 14:39:00 31SVA640_304

ENGINE OIL DIPSTICK (Orange handle)

ENGINE OIL FILL CAP

BRAKE FLUID (Black cap)

Si model

WASHER FLUID (Blue cap)

Fluid Locations

CLUTCH FLUID (Light gray cap)

ENGINE COOLANT RESERVOIR

RADIATOR CAP

299

09/07/07 14:39:10 31SVA640_305

Adding Engine Oil

ENGINE OIL FILL CAP

ENGINE OIL FILL CAP

DX, Canadian DX-G, LX, EX, EX-L

Si

Unscrew and remove the engine oil fill cap on the valve cover. Pour the oil slowly and carefully so you do not spill any. Clean up any spills immediately. Spilled oil could damage components in the engine compartment.

Reinstall the engine oil fill cap, and tighten it securely. Wait a few minutes, and recheck the oil level on the engine oil dipstick. Do not fill above the upper mark; you could damage the engine.

300

Recommended Engine Oil Oil is a major contributor to your engine’s performance and longevity. Always use a premium-grade detergent oil displaying the API Certification Seal. This seal indicates the oil is energy conserving, and that it meets the American Petroleum Institute’s latest requirements. It is highly recommended that you use Honda Motor Oil in your vehicle for optimum engine protection.

API CERTIFICATION SEAL

09/07/07 14:39:20 31SVA640_306

Make sure the API Certification Seal says ‘‘For Gasoline Engines.’’

Si model:

The oil viscosity or weight is provided on the container’s label.

DX, Canadian DX-G, LX, EX, and EX-L models: Honda Motor Oil is the preferred 5W-20 lubricant for your vehicle. 5W-20 oil is formulated for year- round protection of your vehicle, to improve cold weather starting and fuel economy.

Ambient Temperature

Ambient Temperature

An oil with a viscosity of 5W-30 is preferred for improved fuel economy and year-round protection in your vehicle. You may use a 10W-30 oil if the temperature in your area never goes below 20°F (

7°C).

−

Adding Engine Oil

Synthetic Oil You may use a synthetic motor oil if it meets the same requirements given for a conventional motor oil: it displays the API Certification Seal, and it is the proper weight. You must follow the oil and filter change intervals shown on the information display.

Engine Oil Additives Your vehicle does not require any oil additives. Additives may adversely affect the engine or transmission performance and durability.

301

09/07/07 14:39:29 31SVA640_307

Changing the Engine Oil and Filter

WASHER

DRAIN BOLT

WASHER

DRAIN BOLT

DX, Canadian DX-G, LX, EX, EX-L

1.

Run the engine until it reaches normal operating temperature, then shut it off.

2.

Si Open the hood, and remove the engine oil fill cap. Remove the oil drain bolt and washer from the bottom of the engine. Drain the oil into an appropriate container.

Always change the oil and filter according to the maintenance messages shown on the information display. The oil and filter collect contaminants that can damage your engine if they are not removed regularly.

Changing the oil and filter requires special tools and access from underneath the vehicle. The vehicle should be raised on a service station- type hydraulic lift for this service. Unless you have the knowledge and proper equipment, you should have this maintenance done by a skilled technician.

302

09/07/07 14:39:42 31SVA640_308

OIL FILTER

Changing the Engine Oil and Filter

OIL FILTER

6.

Refill the engine with the recommended oil. Engine oil change capacity (including filter):

DX, Canadian DX-G, LX, EX, EX-L

Si

3.

Remove the oil filter, and let the remaining oil drain. A special wrench (available from your dealer) is required.

Make sure the oil filter gasket is not stuck to the contacting surface of the engine. If it is, remove it before installing a new oil filter.

4.

Install a new oil filter according to the instructions that come with it.

Make sure to clean off any dirt and dust on the contacting surface of a new oil filter.

5.

Put a new washer on the drain bolt, then reinstall the drain bolt. Tighten the drain bolt to: 29 lbf·ft (39 N·m , 4.0 kgf·m)

DX, Canadian DX-G, LX, EX, EX-L 3.9 US qt (3.7 )

Si 4.6 US qt (4.4 )

7.

Reinstall the engine oil fill cap. Start the engine. The oil pressure indicator should go out within 5
seconds. If it does not, turn off the engine, and check your work.

8.

Let the engine run for several minutes, then check the drain bolt and oil filter for leaks.

CONTINUED

303

09/07/07 14:39:50 31SVA640_309

Changing the Engine Oil and Filter, Engine Coolant

9.

Turn off the engine, let it sit for several minutes, then check the oil level on the dipstick. If necessary, add more oil.

Adding Engine Coolant

RESERVE TANK

RESERVE TANK

Improper disposal of engine oil can be harmf ul to the environment. If you change your own oil, please dispose of the used oil properly. Put it in a sealed container and take it to a recycling center. Do not discard it in a trash bin or dump it on the ground.

304

DX, Canadian DX-G, LX, EX, EX-L

Si

If the coolant level in the reserve tank is at or below the MIN line, add coolant to bring it up to the MAX line. Inspect the cooling system for leaks.

Always use Honda Long-life Anti- freeze/Coolant Type 2. This coolant is pre-mixed with 50 percent antifreeze and 50 percent distilled water. Never add straight antifreeze or plain water.

09/07/07 14:39:57 31SVA640_310

If Honda antifreeze/coolant is not available, you may use another major-brand non-silicate coolant as a temporary replacement. Make sure it is a high-quality coolant recommended for aluminum engines. Continued use of any non-Honda coolant can result in corrosion, causing the cooling system to malfunction or fail. Have the cooling system flushed and refilled with Honda antifreeze/coolant as soon as possible.

If the reserve tank is completely empty, you should also check the coolant level in the radiator.

Removing the radiator cap while the engine is hot can cause the coolant to spray out, seriously scalding you.

Always let the engine and radiator cool down before removing the radiator cap.

Engine Coolant

RADIATOR CAP

DX, Canadian DX-G, LX, EX, EX-L

1.

Make sure the engine and radiator are cool.

2.

Relieve any pressure in the cooling system by turning the radiator cap counterclockwise, without pressing down.

CONTINUED

305

09/07/07 14:40:07 31SVA640_311

Engine Coolant

RADIATOR CAP

RESERVE TANK

RESERVE TANK

Si

DX, Canadian DX-G, LX, EX, EX-L

Si

3.

Remove the radiator cap by pushing down and turning counterclockwise.

4.

The coolant level should be up to the base of the filler neck. Add coolant if it is low.

Pour the coolant slowly and carefully so you do not spill any. Clean up any spill immediately; it could damage components in the engine compartment.

5.

Put the radiator cap back on, and tighten it fully.

6.

Pour coolant into the reserve tank. Fill it to halfway between the MAX and MIN marks. Put the cap back on the reserve tank.

Do not add any rust inhibitors or other additives to your vehicle’s cooling system. They may not be compatible with the coolant or engine components.

306

09/07/07 14:40:15 31SVA640_312

Check the fluid level in the windshield washer reservoir at least monthly during normal use.

LEVEL GAUGE

LEVEL GAUGE

Si

DX, Canadian DX-G, LX, EX, EX-L

Check the fluid level by removing the cap and looking at the level gauge.

OnCanadianmodels: level indicator comes on when the level is low (see page

The low washer

63

).

Fill the reservoir with a good-quality windshield washer fluid. This increases the cleaning capability and prevents freezing in cold weather.

Windshield Washers

When you refill the reservoir, clean the edges of the windshield wiper blades with windshield washer fluid on a clean cloth. This will help to condition the blade edges.

Do not use engine antif reeze or a vinegar/water solution in the windshield washer reservoir. Antif reeze can damage your vehicle’s paint, while a vinegar/water solution can damage the windshield washer pump. Use only commercially-available windshield washer f luid.

307

09/07/07 14:40:26 31SVA640_313

Automatic Transmission Fluid

DIPSTICK

UPPER MARK LOWER