ABS. If this happens, have your vehicle checked at a dealer. With this indicator on, your vehicle still has normal braking ability but no anti-lock function. For more information, see page
214
Immobilizer System Indicator
This indicator comes on briefly when you turn the ignition switch to the ON (II) position. It will then go off if you have inserted a properly-coded ignition key. If it is not a properly- coded key, the indicator will blink, and the engine’s fuel system will be disabled (see page
77
).
Turn Signal and Hazard Warning Indicators The left or right turn signal indicator blinks when you signal a lane change or turn. If an indicator does not blink or blinks rapidly, it usually means one of the turn signal bulbs is burned out (see pages ). and Replace the bulb as soon as possible, since other drivers cannot see that you are signaling.
249
250
When you press the hazard warning button, both turn signal indicators and all turn signals on the outside of the vehicle flash.
59
2008 Civic Coupe Table Of ContentsMain Menu07/10/30 14:05:13 31SVA620 0065
If you turn the steering wheel to the full left or right position repeatedly while stopping or driving at very low speed, you may feel slightly harder steering due to overheating of the steering gearbox.
Continuously driving under those conditions could damage the power steering system.
Instrument Panel Indicators
Electric Power Steering (EPS) Indicator
SiandCanadianDX-Gwithmanual transmissionmodels This indicator normally comes on when you turn the ignition switch to the ON (II) position and goes off after the engine starts. If it comes on at any other time, there is a problem in the electric power steering system. If this happens, stop the vehicle in a safe place, and turn off the engine. Reset the system by restarting the engine. The indicator will not turn off immediately. If it does not go off after driving a short distance, or comes back on again while driving, take the vehicle to your dealer to have it checked. With the indicator on, the EPS may be off, making the vehicle harder to steer.
60
Maintenance Minder Indicator
This indicator comes on for a few
seconds when you turn the ignition
switch to the ON (II) position. It
reminds you that it is time to take
your vehicle in for scheduled
maintenance. The maintenance main
items and sub items will be displayed
in the information display. See page
225
maintenance minder.
for more information on the
This indicator goes off when your dealer resets it after completing the required maintenance service.
2008 Civic Coupe Table Of ContentsMain Menu07/07/11 15:15:40 31SVA620 0066
Low Tire Pressure Indicator
U.S.modelsonly This indicator normally comes on for a few seconds when you turn the ignition switch to the ON (II) position. If it comes on while driving, it indicates that one or more of your vehicle’s tires are significantly low on pressure.
If this happens, pull to the side of the road when it is safe, check which tire has lost the pressure, and determine the cause. If it is because of a flat tire, replace the flat tire with the compact spare (see page ), and have the flat tire repaired as soon as possible. If two or more tires are underinflated, call a professional towing service (see page information, see page
). For more
218
271
290
Tire Pressure Monitoring System (TPMS) Indicator
U.S.modelsonly This indicator normally comes on for a few seconds when you turn the ignition switch to the ON (II) position.
If this indicator comes on and stays on at any other time, or if it does not come on when you turn the ignition switch to the ON (II) position, there is a problem with the TPMS. With this indicator on, the low tire pressure indicator will not come on when a tire loses pressure. Take the vehicle to your dealer to have the system checked.
Instrument Panel Indicators
Rev Limit Indicator
REV LIMIT INDICATOR
Simodelonly This indicator shows you when the engine speed is near the tachometer’s red zone. When the engine speed gets to near the red zone, the indicator blinks. If you exceed the maximum speed for the gear you are in, the indicator stays on, and you may feel the engine cut in and out due to the engine speed limiter (see page
207
).
To protect the engine from damage, never drive with the tachometer in its red zone.
61
2008 Civic Coupe Table Of ContentsMain Menu07/07/11 15:15:54 31SVA620 0067
Instrument Panel Indicators
Cruise Main Indicator
Ifequipped This indicator comes on when you turn on the cruise control system by pressing the CRUISE button (see page
182
).
Cruise Control Indicator
Ifequipped
This indicator comes on when you
set the cruise control. See page
182
cruise control.
for information on operating the
62
Vehicle Stability Assist (VSA) System Indicator
Ifequipped This indicator normally comes on for a few seconds when you turn the ignition switch to the ON (II) position.
If it comes on and stays on at any
other time, or if it does not come on
when you turn the ignition switch to
the ON (II) position, there is a
problem with the VSA system. Take
your vehicle to a dealer to have it
checked. Without VSA, your vehicle
still has normal driving ability, but
will not have VSA traction and
stability enhancement. See page
216
for more information on the
VSA system.
VSA Activation Indicator
Ifequipped This indicator has three functions:
1.
2.
3.
It comes on as a reminder that you have turned off the vehicle stability assist (VSA) system.
It flashes when VSA is active (see page
216
).
It comes on along with the VSA system indicator if there is a problem with the VSA system.
This indicator normally comes on for a few seconds when you turn the ignition switch to the ON (II) for more position. See page information on the VSA system.
216
2008 Civic Coupe Table Of ContentsMain Menu07/07/11 15:16:04 31SVA620 0068
Daytime Running Lights Indicator
If this indicator comes on when you turn the ignition switch to the ON (II) position and release the parking brake, it means there is a problem with the DRL. There may also be a problem with the high beam headlights. Have your vehicle checked by your dealer.
High Beam Indicator
This indicator comes on with the high beam headlights. For more information, see page
72
This indicator also comes on with reduced brightness when the daytime running lights (DRL) are on (see page
73
).
Instrument Panel Indicators
Trunk-open Indicator
Lights On Indicator
This indicator comes on if the trunk lid is not closed tightly.
Door-open Indicator
This indicator comes on if either door is not closed tightly.
Washer Level Indicator
Canadianmodelsonly This indicator comes on when the washer fluid level is low. Add washer fluid when you see this indicator (see page
241
).
or
This indicator reminds you that the exterior lights are on. It comes on when the light switch is in either the position. If you turn the
ignition switch to the ACCESSORY (I) or LOCK (0) position without turning off the light switch, this indicator will stay on. A reminder chime will also sound when you open the driver’s door.
63
2008 Civic Coupe Table Of ContentsMain Menu07/10/30 14:13:04 31SVA620 0069
Instrument Panel Indicators
Security System Indicator
Low Fuel Indicator
Except Si
Si
LOW FUEL INDICATOR
SECURITY SYSTEM INDICATOR
Ifequipped
This indicator comes on when the
security system is set. See page
181
for more information on the
security system.
64
This indicator is located in the fuel gauge. It comes on as a reminder that you must refuel soon.
When the indicator comes on, there are about 1.9 US gal (7.5 ) of fuel remaining in the tank. When the reading reaches E, there is a very small amount of fuel in the tank.
2008 Civic Coupe Table Of ContentsMain Menu07/07/11 15:16:16 31SVA620 0070
TEMPERATURE GAUGE
SPEEDOMETER
TACHOMETER
FUEL GAUGE
Gauges
SEL/RESET BUTTON
ODOMETER/OUTSIDE TEMPERATURE INDICATOR
*
U.S. model with A/T is shown.
*
If equipped
TRIP METER
To switch the information display between the odometer, trip meter, and outside temperature (if equipped), and engine oil life and maintenance service items, press the SEL/RESET button repeatedly.
INFORMATION DISPLAY
65
2008 Civic Coupe Table Of ContentsMain Menu07/07/11 15:16:24 31SVA620 0071
Gauges
Display Change Button
DISPLAY CHANGE BUTTON
Press and hold the display change button until you hear a beep. The speedometer, trip meter, and odometer readings switch between miles per hour (mph) and kilometers per hour (km/h).
66
Odometer This shows the total distance your vehicle has been driven. It measures miles or kilometers. It is illegal under U.S. federal law and Canadian provincial regulations to disconnect, reset, or alter the odometer with the intent to change the number of miles or kilometers indicated.
The odometer and the outside temperature indicator (if equipped) use the same display. To switch the display between them, press the SEL/RESET button repeatedly. When you turn the ignition switch to the ON (II) position, your last selection is displayed.
Trip Meter This meter shows the number of miles or kilometers driven since you last reset it.
There are two trip meters: Trip A and Trip B. Switch between these displays by pressing the SEL/ RESET button repeatedly. Each trip meter works independently, so you can keep track of two different distances.
When you turn the ignition switch to the ON (II) position, what you last selected is displayed.
To reset a trip meter, display it, and then press and hold the SEL/RESET button until the number resets to ‘‘0.0.’’
2008 Civic Coupe Table Of ContentsMain Menu07/07/11 15:16:32 31SVA620 0072
Outside Temperature Indicator Ifequipped This indicator displays the outside temperature in Fahrenheit (U.S. models) or Centigrade (Canadian models). To see the outside temperature, press and release the SEL/RESET button until the temperature is shown on the information display.
The temperature sensor is in the front bumper. Therefore, the temperature reading can be affected by heat reflection from the road surface, engine heat, and the exhaust from surrounding traffic. This can cause an incorrect temperature reading when your speed is under 19 mph (30 km/h).
The sensor delays the display update until it reaches the correct outside temperature. This may take several minutes.
If the outside temperature is incorrectly displayed, you can adjust it up to 3°C ± in Canadian models) warmer or cooler.
5°F in U.S. models (
±
NOTE: The temperature must be stabilized before doing this procedure.
Select the outside temperature display, then press and hold the SEL/RESET button for 10 seconds. The following sequence will appear for 1 second each: 0, 1, 2, 3, 4, 5, 5, − 1, 0 (U.S.) or 0, 1, 2, − − − − 3,
4, 2, − − −
1, 0 (Canada).
3,
3,
2,
When it reaches the desired value, release the SEL/RESET button. You should see the new outside temperature displayed.
Gauges
In certain weather conditions, temperature readings near freezing (32°F, 0°C) could mean that ice is forming on the road surface.
67
2008 Civic Coupe Table Of ContentsMain Menu07/07/11 15:16:38 31SVA620 0073
Temperature Gauge This shows the temperature of the engine’s coolant. During normal operation, the reading should rise to about the middle of the gauge. In severe driving conditions, such as very hot weather or a long period of uphill driving, the reading may rise into the upper half of the gauge. If it reaches the red (Hot) mark, pull safely to the side of the road. See page precautions on checking the engine cooling system.
for instructions and
279
Check Fuel Cap Message Your vehicle’s onboard diagnostic system will detect a loose or missing fuel fill cap as an evaporative system leak. The first time a leak is detected a ‘‘CHECK FUEL CAP’’ message appears on the information display. Turn the engine off, and confirm the fuel fill cap is installed. If it is, loosen it, then retighten it until it clicks at least once. The message should go off after several days of normal driving once you tighten or replace the fuel fill cap. To scroll to another display, press the SEL/RESET button. The ‘‘CHECK FUEL CAP’’ message will appear each time you restart the engine until the system turns the message off.
Gauges
Fuel Gauge This shows how much fuel you have. It may show slightly more or less than the actual amount.
Avoid driving with an extremely low f uel level. Running out of f uel could cause the engine to misf ire, damaging the catalytic converter.
68
2008 Civic Coupe Table Of ContentsMain Menu07/07/11 15:16:43 31SVA620 0074
If the system still detects a leak in your vehicle’s evaporative emissions system, the malfunction indicator lamp (MIL) comes on. If the fuel fill cap was not already tightened, turn the engine off, and check or retighten the fuel fill cap until it clicks at least once. The MIL should go off after several days of normal driving once the cap is tightened or replaced. If the MIL does not go off, have your vehicle inspected by a dealer. For more information, see page
282
Maintenance Minder The information display in the instrument panel shows you the engine oil life and maintenance service items when the ignition switch is in the ON (II) position. This information helps to keep you aware of the periodic maintenance your vehicle needs for continued trouble- free driving. Refer to page more information.
225
for
Gauges
69
2008 Civic Coupe Table Of ContentsMain MenuWINDSHIELD WIPERS/WASHERS (P.71)
PASSENGER’S AIRBAG OFF INDICATOR
(P.29)
07/07/11 15:16:51 31SVA620 0075
Controls Near the Steering Wheel
HEADLIGHTS/ TURN SIGNALS (P.72) INSTRUMENT PANEL BRIGHTNESS (P.73)
MIRROR CONTROLS (P.104)
*
VEHICLE STABILITY ASSIST (VSA) SYSTEM OFF SWITCH * (P.217)
AUDIO SYSTEM * (P.119)
REAR WINDOW DEFOGGER (P.74) HEATED MIRRORS (P.105)
*
HAZARD WARNING BUTTON
(P.74)
ACCESSORY POWER SOCKET
(P.108)
AUXILIARY INPUT JACK (P.178)
*
NAVIGATION SYSTEM VOICE CONTROL BUTTONS
*
Vehicle without navigation system is shown.
HORN
*
REMOTE AUDIO CONTROLS (P.177)
*
STEERING WHEEL ADJUSTMENTS (P.75)
CRUISE CONTROL BUTTONS (P.182)
*
To use the horn, press the center pad of the steering wheel. If equipped. Only on vehicles equipped with navigation system. Refer to the navigation system manual.
1:
*
2:
*
3:
*
70
2008 Civic Coupe Table Of ContentsMain Menu07/07/11 15:17:00 31SVA620 0076
Windshield Wipers and Washers
MIST The wipers run at high speed until you release the lever.
−
OFF
−
The wipers are not activated.
−
INT few seconds.
The wipers operate every
ADJUSTMENT RING
*
*
: EX, EX-L, Si, Canadian LX
1. 2. 3. 4. 5. 6.
MIST OFF INT LO Low speed HI High speed Windshield washers
Intermittent
− − −
Push the right lever up or down to select a position.
OnEX,EX-LandSimodelsintheU.S., andLX,EX,EX-LandSimodelsin Canada The length of the wiper interval is varied automatically according to the vehicle’s speed.
Vary the delay by turning the adjustment ring. If you turn it to the shortest delay ( position), the wipers change to low speed operation when the vehicle speed exceeds 12 mph (20km/h).
LO
−
The wipers run at low speed.
HI
−
The wipers run at high speed.
−
Windshield Washers Pull the wiper control lever toward you, and hold it. The washers spray until you release the lever. The wipers run at low speed, then complete one more sweep after you release the lever.
71
2008 Civic Coupe Table Of ContentsMain Menu07/07/11 15:17:09 31SVA620 0077
Turn Signals and Headlights
−
Turn Signal Push down on the lever to signal a left turn and up to signal a right turn. To signal a lane change, push lightly on the lever, and hold it. The lever will return to center when you release it or complete a turn.
−
Turning the ’’ position turns
Headlights On switch to the ‘‘ on the parking lights, taillights, instrument panel lights, side-marker lights, and rear license plate lights.
Turning the switch to the ‘‘ position turns on the headlights.
’’
If you leave the lights on with the key removed from the ignition switch, you will hear a reminder chime when you open the driver’s door.
1. 2. 3. 4. 5. 6.
Turn signal Off Parking and indicator lights Headlights on High beams Flash high beams
72
’’ or ‘‘
When the light switch is in the ‘‘ ’’ position, the lights on indicator comes on as a reminder.
This indicator stays on if you leave the lights on and turn the ignition switch to the ACCESSORY (I) or LOCK (0) position.
−
Push the lever
High Beams forward until you hear a click. The high beam indicator will come on (see page return to the low beams.
). Pull the lever back to
63
To flash the high beams, pull the lever back lightly, then release it. The high beams will stay on as long as you hold the lever back.
2008 Civic Coupe Table Of ContentsMain Menu07/07/11 15:17:17 31SVA620 0078
position, the high beam
Daytime Running Lights With the headlight switch off or in the headlights and the high beam indicator come on with reduced brightness when you turn the ignition switch to the ON (II) position and release the parking brake. They remain on until you turn the ignition switch off, even if you set the parking brake.
The headlights revert to normal operation when you turn them on with the switch.
Headlights, Instrument Panel Brightness
Instrument Panel Brightness
CONTROL BUTTONS
when you reach the maximum or minimum brightness. The display returns to the odometer 5 seconds after you stop adjusting the brightness.
To reduce glare at night, the instrument panel illumination dims when you turn the light switch to the
or
position.
The buttons under the left side vent control the brightness of the instrument panel. Push the or button to adjust the brightness.
+ −
Separate adjustments can be made when the headlights are on and off.
There are six brightness levels. When you push either button, the information display indicates the current level. You will hear a tone
The center of each meter (upper and lower) illuminates with reduced brightness when you unlock and open the driver’s door, and then goes back to the selected brightness when you turn the ignition switch to the ON (II) position.
If you insert the key but do not turn the ignition switch to the ON (II) position, the illumination turns off in about 10 seconds.
73
2008 Civic Coupe Table Of ContentsMain Menu07/07/11 15:17:25 31SVA620 0079
Hazard Warning Button, Rear Window Defogger
Hazard Warning Button
Rear Window Defogger
Make sure the rear window is clear and you have good visibility before starting to drive.
The defogger and antenna wires on the inside of the rear window can be accidentally damaged. When cleaning the glass, always wipe side- to-side.
OnU.S.EX-L,CanadianLX,EX,EX-L andSimodels Pushing this button also turns the mirror heaters on or off. For more information, see page
105
Push the button to turn on the hazard warning lights (four-way flashers). This causes all four outside turn signals and both turn indicators in the instrument panel to flash. Use the hazard warning lights if you need to park in a dangerous area near heavy traffic, or if your vehicle is disabled.
74
U.S. EX-L, Canadian LX, EX, EX-L, Si The rear window defogger will clear fog, frost, and thin ice from the window. Push the defogger button to turn it on and off. The indicator in the button comes on to show the defogger is on. If you do not turn it off, the defogger will shut itself off after about 15 minutes. It also shuts off when you turn off the ignition switch. You have to turn the defogger on again when you restart the vehicle.
2008 Civic Coupe Table Of ContentsMain Menu07/07/11 15:17:31 31SVA620 0080
Make any steering wheel adjustments before you start driving.
Adjusting the steering wheel position while driving may cause you to lose control of the vehicle and be seriously injured in a crash.
Adjust the steering wheel only when the vehicle is stopped.
1.
Push the lever under the steering column all the way down.
2.
Move the steering wheel up or down, and in or out, so it points toward your chest, not toward your face. Make sure you can see the instrument panel gauges and indicators.
Steering Wheel Adjustments
3.
Push the lever up to lock the steering wheel in position.
4.
Make sure you have securely locked the steering wheel in place by trying to move it up, down, in, and out.
75
2008 Civic Coupe Table Of ContentsMain Menu07/07/11 15:17:39 31SVA620 0081
Keys and Locks
All EX, EX-L and Si models, and Canadian LX model
U.S. LX and Canadian DX-G models
MASTER KEY WITH REMOTE TRANSMITTER
MASTER KEY WITH REMOTE TRANSMITTER
KEY NUMBER TAG
VALET KEY (Gray)
KEY NUMBER TAG
VALET KEY (Gray)
DX model (except Canadian DX-G)
MASTER KEYS (Black)
KEY NUMBER TAG
VALET KEY (Gray)
76
The master key fits all the locks on your vehicle. The valet key works only in the ignition and the driver’s door lock . You can keep the trunk and trunk release handle locked when you leave your vehicle and the valet key at a parking facility.
*
*
On DX model (except Canadian DX-G), the passenger’s door can also be locked or unlocked with the key.
You should have received a key number tag with your keys. You will need this key number if you ever have to get a lost key replaced. Use only Honda-approved key blanks.
2008 Civic Coupe Table Of ContentsMain Menu07/07/11 15:17:49 31SVA620 0082
Keys and Locks, Immobilizer System
These keys contain electronic circuits that are activated by the immobilizer system. They will not work to start the engine if the circuits are damaged.
Protect the keys from direct sunlight, high temperature, and high humidity.
Do not drop the keys or set heavy objects on them.
Keep the keys away from liquids. If they get wet, dry them immediately with a soft cloth.
The valet key does not contain a battery. Do not try to take it apart.
OnDXmodel(exceptCanadianDX-G) The keys do not contain batteries. Do not try to take them apart.
Immobilizer System The immobilizer system protects your vehicle from theft. If an improperly-coded key (or other device) is used, the engine’s fuel system is disabled.
When you turn the ignition switch to the ON (II) position, the immobilizer system indicator should come on briefly, then go off. If the indicator starts to blink, it means the system does not recognize the coding of the key. Turn the ignition switch to the LOCK (0) position, remove the key, reinsert it, and turn the ignition switch to the ON (II) position again.
The system may not recognize your key’s coding if another immobilizer key or other metal object (i.e. key fob) is near the ignition switch when you insert the key.
If the system repeatedly does not recognize the coding of your key, contact your dealer.
Do not attempt to alter this system or add other devices to it. Electrical problems could result that may make your vehicle undrivable.
If you have lost your key and cannot start your engine, contact your dealer.
Always take the ignition key with you whenever you leave the vehicle alone.
CONTINUED
77
2008 Civic Coupe Table Of ContentsMain Menu07/07/11 15:17:57 31SVA620 0083
Immobilizer System, Ignition Switch
AsrequiredbytheFCC: ThisdevicecomplieswithPart15ofthe FCCrules.Operationissubjecttothe followingtwoconditions:(1)Thisdevice maynotcauseharmfulinterference,and (2)thisdevicemustacceptany interferencereceived,including interferencethatmaycauseundesired operation.
Changesormodificationsnotexpressly approvedbythepartyresponsiblefor compliancecouldvoidtheuser’s authoritytooperatetheequipment.
ThisdevicecomplieswithIndustry CanadaStandardRSS-210. Operationissubjecttothefollowingtwo conditions:(1)thisdevicemaynotcause interference,and(2)thisdevicemust acceptanyinterferencethatmaycause undesiredoperationofthedevice.
78
Ignition Switch
If the front wheels are turned, the anti-theft lock may make it difficult to turn the key. Firmly turn the steering wheel to the left or right as you turn the key.
−
You can
ACCESSORY (I) operate the audio system and the accessory power sockets in this position.
The ignition switch has four positions: LOCK (0), ACCESSORY (I), ON (II), and START (III).
−
You can insert or
LOCK (0) remove the key only in this position. To turn the key, push it in slightly. If your vehicle has an automatic transmission, the shift lever must also be in park.
−
This is the normal key
ON (II) position when driving. Several of the indicators on the instrument panel come on as a test when you turn the ignition switch from the ACCESSORY (I) to the ON (II) position.
−
Use this position
START (III) only to start the engine. The switch returns to the ON (II) position when you let go of the key.
2008 Civic Coupe Table Of ContentsMain Menu07/07/11 15:18:05 31SVA620 0084
You will hear a reminder beeper if you leave the key in the ignition switch in the LOCK (0) or the ACCESSORY (I) position and open the driver’s door. Remove the key to turn off the beeper.
If your vehicle has an automatic transmission, the shift lever must be in Park before you can remove the key from the ignition switch.
Removing the key from the ignition switch while driving locks the steering. This can cause you to lose control of the vehicle.
Remove the key from the ignition switch only when parked.
Door Locks
LOCK
LOCK TAB
UNLOCK
RED MARK
Each door has a lock tab next to the inside door handle. Pull out the tab to lock the door, and push it in to unlock.
When the door is unlocked, the red mark on the lock tab is shown.
Ignition Switch, Door Locks
OnDXmodelexceptCanadianDX-G To lock the passenger’s door when getting out of the vehicle, pull out the lock tab and close the door. To lock the driver’s door, pull and hold the outside door handle then pull out the lock tab. Release the handle, then close the door.
Each door can be locked or unlocked with the ignition key.
79
2008 Civic Coupe Table Of ContentsMain Menu07/07/11 15:18:12 31SVA620 0085
The lock tab on the passenger’s door locks and unlocks only that door. Pushing in the driver’s door lock tab only unlocks the driver’s door. To unlock only the driver’s door from the outside, turn the key and release it. If you turn it again, both doors unlock.
To lock the passenger’s door when getting out of the vehicle, pull out the lock tab and close the door. To lock the driver’s door, remove the key from the ignition switch and pull out the lock tab or push the top of the master switch, then close the door.
LockoutPrevention If you forget and leave the key in the ignition switch, lockout prevention will not allow you to lock the driver’s door. With either door open and the key in the ignition switch, locking with master door lock switch is disabled. If the driver’s door is closed, the lock tab on the driver’s door is not disabled. Pulling the driver’s lock tab rearward will lock both doors. If you try to lock an open driver’s door by pulling the lock tab rearward, the driver’s door lock tab pops out and unlocks the driver’s door.
Door Locks
Power Door Locks
MASTER DOOR LOCK SWITCH
OnLX,EX,EX-LandSimodelsinthe U.S.,andDX-G,LX,EX,EX-LandSi modelsinCanada To lock the doors, push the top of the master door lock switch on either door, pull out the lock tab on the driver’s door, or use the key in the outside lock on the driver’s door.
Pushing the bottom of either master door lock switch unlocks both doors.
80
2008 Civic Coupe Table Of ContentsMain Menu07/08/02 16:19:00 31SVA620 0086
Auto Door Locking/Unlocking OnLX,EX,EX-LandSimodelsinthe U.S.,andDX-G,LX,EX,EX-LandSi modelsinCanada Your vehicle has customizable settings for the doors to automatically lock and unlock. There are default settings for each of these features. You can turn off or change the settings for these features as described on the following pages.
When you customize the setting, make sure your vehicle is parked safely, the engine is off, and apply the parking brake. Make all settings before you start driving.
Door Locks
Auto Door Locking The auto door locking feature has three possible settings:
ToturnofftheAutoDoorLock modes:
The auto door locking is deactivated all the time.
The doors lock whenever you move the shift lever out of the Park (P) position (A/T vehicles).
The doors lock when the vehicle speed reaches 9 mph (15 km/h). This is the default setting.
1.
Make sure the shift lever is in the Park (P) position (A/T vehicles).
2.
Turn the ignition switch to the ON (II) position, and open the driver’s door.
CONTINUED
81
2008 Civic Coupe Table Of ContentsMain Menu07/07/11 15:18:30 31SVA620 0087
Door Locks
3.
Push and hold the front of the master door lock switch on the driver’s door until you hear a click (after about 5 seconds).
ToprogramtheParkLockmode: Locksbothdoorswhentheshiftleveris movedoutofthePark(P)position(A/T vehiclesonly).
4.
Release the switch, and within 5
seconds, turn the ignition switch
to the LOCK (0) position.
3.
Push and hold the front of the
master door lock switch on the
driver’s door. You will hear a click.
Keep holding the switch until you
hear another click (after about 5
seconds).
4.
Release the switch, and within 5
seconds, turn the ignition switch
to the LOCK (0) position.
1.
Make sure the shift lever is in the Park (P) position.
2.
Turn the ignition switch to the ON (II) position, and make sure to close the driver’s door.
82
2008 Civic Coupe Table Of ContentsMain Menu07/07/11 15:18:44 31SVA620 0088
4.
Push and hold the front of the
master door lock switch on the
driver’s door. You will hear a click.
Keep holding the switch until you
hear another click (after about 5
seconds).
5.
Release the switch, and within 5
seconds, turn the ignition switch
to the ACCESSORY (I) position.
move the shift
OnA/Tvehicles,
lever to the Park (P) position.
6.
Turn the ignition switch to the LOCK (0) position.
ToprogramtheDriveLockmode: Locksbothdoorswhenthevehicle’s speedreachesabout9mph(15km/h).
1.
Make sure the shift lever is in the Park (P) position (A/T vehicles).
2.
3.
Turn the ignition switch to the ON (II) position, and make sure to close the driver’s door.
OnA/Tvehicles, brake pedal, and move the shift lever out of the Park (P) position.
push and hold the
Door Locks
Auto Door Unlocking The auto door unlocking feature has five possible settings:
The auto door unlocking is deactivated all the time.
the driver’s door OnA/Tvehicles, unlocks when you move the shift lever to the Park (P) position. This is the default setting.
Both doors unlock when you move the shift lever to the Park (P) position (A/T vehicles).
The driver’s door unlocks whenever you turn the ignition switch to the ACCESSORY (I) position. This is the default setting on M/T vehicles.
Both doors unlock whenever you turn the ignition switch to the ACCESSORY (I) position.
CONTINUED
83
2008 Civic Coupe Table Of ContentsMain Menu07/07/11 15:18:53 31SVA620 0089
Door Locks
ToturnofftheAutoDoorUnlock modes:
1.
Make sure the shift lever is in the Park (P) position (A/T vehicles).
2.
Turn the ignition switch to the ON (II) position, and open the driver’s door.
84
3.
Push and hold the rear of the master door lock switch on the driver’s door. You will hear a click, and after about 5 seconds, you will hear another click.
4.
Release the switch, and within 5
seconds, turn the ignition switch
to the LOCK (0) position.
ToprogramtheParkUnlockmode: Unlocksthedriver’sdoororbothdoors whentheshiftleverismovedintothe Park(P)position(A/Tvehiclesonly).
1.
Make sure the shift lever is in the Park (P) position.
2.
Turn the ignition switch to the ON (II) position, and make sure to close the driver’s door.
2008 Civic Coupe Table Of ContentsMain Menu07/07/11 15:19:03 31SVA620 0090
3.
Push and hold the rear of the master door lock switch on the driver’s door. You will hear a click. Continue to hold the switch:
Until you hear another click (after about 5 seconds) to activate driver’sdoorunlock feature,
Or, until you hear two more clicks (after about 10 seconds) to activate feature
bothdoorsunlock
4.
Release the switch, and within 5
seconds, turn the ignition switch
to the LOCK (0) position.
ToprogramtheIgnitionSwitch Unlockmode: Unlocksthedriver’sdoororbothdoors whentheignitionswitchismovedoutof theON(II)position.
3.
4.
1.
Make sure the shift lever is in the Park (P) position (A/T vehicles).
2.
Turn the ignition switch to the ON (II) position, and make sure to close the driver’s door.
Door Locks
OnA/Tvehicles, brake pedal, then move the shift lever out of the Park (P) position.
push and hold the
Push and hold the rear of the master door lock switch on the driver’s door. You will hear a click. Continue to hold the switch:
Until you hear another click (after about 5 seconds) to activate feature.
driver’sdoorunlock
Or, until you hear two more clicks (after about 10 seconds) to activate feature
bothdoorsunlock
CONTINUED
85
2008 Civic Coupe Table Of ContentsMain Menu07/07/11 15:19:12 31SVA620 0091
Door Locks, Remote Transmitter
5.
Release the switch, and within 5
seconds, turn the ignition switch
to the ACCESSORY (I) position.
move the shift
OnA/Tvehicles,
lever to the Park (P) position.
6.
Turn the ignition switch to the LOCK (0) position.
Even though your vehicle’s battery is removed or goes dead, the system keeps the auto door lock/unlock setting which you selected.
Remote Transmitter
U.S.: LX Canada: DX-G
LED
UNLOCK BUTTON
PANIC BUTTON
U.S.: EX, EX-L, Si Canada: LX, EX, EX-L, Si
LOCK BUTTON
LED
UNLOCK BUTTON
PANIC BUTTON
LOCK BUTTON
TRUNK RELEASE BUTTON
−
Press this button once to
U.S.:LX,EX,EX-L,Si Canada:DX-G,LX,EX,EX-L,Si LOCK lock both doors. Some exterior lights will flash once. When you push LOCK twice within 5 seconds, you will hear a beep to verify that the doors are locked and that the security system (if equipped) has set. You cannot lock the doors if either door is not fully closed or the key is in the ignition switch.
86
−
Press this button once
UNLOCK to unlock the driver’s door. Push it twice to unlock the passenger’s door. Some exterior lights will flash twice each time you push the button.
2008 Civic Coupe Table Of ContentsMain Menu07/07/11 15:19:20 31SVA620 0092
The ceiling light and the door
activated spotlights (if equipped)
come on when you press the
UNLOCK button if the lights are in
the door activated position. If you do
not open either door within 30
seconds, the light(s) will fade out. If
you relock the doors with the remote
transmitter before 30 seconds have
elapsed, the light(s) will go off
immediately.
If you do not open either door within 30 seconds, the doors automatically relock, and the security system (if equipped) sets. You cannot unlock it if the key is in the ignition switch.
EX,EX-L,SiandCanadianLXmodels TRUNK RELEASE Press this button for about 1 second to open the trunk. You cannot open the trunk if the key is in the ignition switch.
−
−
Press and hold this
PANIC button for about 2 seconds to attract attention: the horn will sound and the exterior lights will flash for about 30 seconds. To cancel panic mode, press any other button on the remote transmitter, or turn the ignition switch to the ON (II) position.
Remote Transmitter
RemoteTransmitterCare
Avoid dropping or throwing the transmitter.
Protect the transmitter from extreme temperature.
Do not immerse the transmitter in any liquid.
If you lose a transmitter, the replacement needs to be reprogrammed by your dealer.
CONTINUED
87
2008 Civic Coupe Table Of ContentsMain Menu07/07/11 15:19:28 31SVA620 0093
Remote Transmitter
Replacing the Transmitter Battery If it takes several pushes on the button to lock or unlock the doors, replace the battery as soon as possible.
Battery type: CR1616
To replace the battery: 1.
Remove the screw at the base of the transmitter with a small Phillips-head screwdriver.
NOTE: Be careful when removing this screw as the head of the screw can strip out.
88
BATTERY
SCREW
Model with trunk release is shown.
2.
Separate the transmitter by prying its middle seam with your fingernail.
TAB
3.
Inside the transmitter, separate the inner cover from the keypad by releasing the two tabs on the cover.
2008 Civic Coupe Table Of ContentsMain Menu07/07/12 17:24:12 31SVA620 0094
Remote Transmitter
4.
Remove the old battery from the back of the inner cover, and insert a new battery into the back of the cover with the
side facing down.
+
An improperly disposed of battery can be harmful to the environment and human health. Always confirm local regulations for battery disposal.
5.
Install the parts in reverse order.
AsrequiredbytheFCC: ThisdevicecomplieswithPart15ofthe FCCrules.Operationissubjecttothe followingtwoconditions:(1)Thisdevice maynotcauseharmfulinterference,and (2)thisdevicemustacceptany interferencereceived,including interferencethatmaycauseundesired operation.
Changesormodificationsnotexpressly approvedbythepartyresponsiblefor compliancecouldvoidtheuser’s authoritytooperatetheequipment.
ThisdevicecomplieswithIndustry CanadaStandardRSS-210. Operationissubjecttothefollowingtwo conditions:(1)thisdevicemaynotcause interference,and(2)thisdevicemust acceptanyinterferencethatmaycause undesiredoperationofthedevice.
89
2008 Civic Coupe Table Of ContentsMain Menu07/07/11 19:57:05 31SVA620 0095
Trunk
Pull
U.S. DX and LX, Canadian DX and DX-G
Keep the trunk lid closed at all times
while driving to avoid damaging the
lid, and to prevent exhaust gas from
Carbon
getting into the interior. See
Monoxide Hazard
50
on page
TRUNK RELEASE HANDLE
MASTER KEY
You can open the trunk in two ways:
Pull the trunk release handle to the left of the driver’s seat.
OnEX,EX-L,Siand CanadianLXmodels Press and hold the trunk release button on the remote transmitter.
OnU.S.DXandLXmodels,and CanadianDXandDX-Gmodels Use the master key to open the trunk lock. The valet key does not work in this lock.
To close the trunk, press down on the trunk lid.
90
2008 Civic Coupe Table Of ContentsMain Menu07/07/11 15:19:50 31SVA620 0096
Trunk
Emergency Trunk Opener
OnEX,EX-L,SiandCanadianLX Even if the trunk release lever is locked with the master key, you can open the trunk with the remote transmitter.
As a safety feature, your vehicle has a release lever on the trunk latch so the trunk can be opened from the inside. To open the trunk, push the release lever to the left.
Parents should decide if their children should be shown how to use this feature. For more information about child safety, see page
35
91
MASTER KEY
To protect items in the trunk when you need to give the key to someone else:
1.
Lock the trunk release handle