uuChild SafetyuSafety of Infants and Small Children
Tether Strap Hook
Anchor
3. Open the tether anchor cover behind the
1Installing a LATCH-Compatible Child Seat
For your child's safety, when using a child seat installed using the LATCH system, make sure that the seat is properly secured to the vehicle. A child seat that is not properly secured will not adequately protect a child in a crash and may cause injury to the child or other vehicle occupants.
head restraint.
4. Raise the head restraint to its highest position, then route the tether strap between the head restraint legs, and secure the tether strap hook onto the anchor.
5. Tighten the tether strap as instructed by the
child seat maker.
6. Make sure the child seat is firmly secured by
rocking it forward and back and side to side; little movement should be felt.
7. Make sure any unused seat belt that a child can reach is buckled, the lockable retractor is activated, and the belt is fully retracted and locked.
QRG
TOC
Index
Home
58
2013 Accord Sedan13 ACCORD 4D US-31T2A6000.book 59 ページ 2012年10月3日 水曜日 午後4時21分
■ Installing a Child Seat with a Lap/Shoulder Seat Belt
1. Place the child seat on the vehicle seat.
2. Route the seat belt through the child seat according to the seat maker's instructions, and insert the latch plate into the buckle. u Insert the latch plate fully until it clicks.
3. Slowly pull the shoulder part of the belt all the way out until it stops. This activates the lockable retractor.
4. Let the seat belt completely wind up into
the retractor, then try to pull it out to make sure the retractor is locked. u If you are able to pull the shoulder belt
out, the lockable retractor is not activated. Pull the seat belt all the way out, and repeat steps 2 – 4.
5. Grab the shoulder part of the seat belt near the buckle, and pull up to remove any slack from the lap part of the belt. u When doing this, place your weight on the child seat and push it into the vehicle seat.
Continued
uuChild SafetyuSafety of Infants and Small Children
1Installing a Child Seat with a Lap/Shoulder Seat Belt
A child seat that is not properly secured will not adequately protect a child in a crash and may cause injury to the child or other vehicle occupants.
QRG
TOC
Index
Home
59
2013 Accord Sedan13 ACCORD 4D US-31T2A6000.book 60 ページ 2012年10月3日 水曜日 午後4時21分
uuChild SafetyuSafety of Infants and Small Children
6. Make sure the child seat is firmly secured by
rocking it forward and back and side to side; little movement should be felt.
7. Make sure any unused seat belt that a child can reach is buckled, the lockable retractor is activated, and the belt is fully retracted and locked.
1Installing a Child Seat with a Lap/Shoulder Seat Belt
To deactivate a lockable retractor, release the buckle and allow the seat belt to wind up all the way.
QRG
TOC
Index
Home
60
2013 Accord SedanuuChild SafetyuSafety of Infants and Small Children
1Adding Security with a Tether
Since a tether can provide additional security to the lap/shoulder seat belt installation, we recommend using a tether whenever one is available.
13 ACCORD 4D US-31T2A6000.book 61 ページ 2012年10月3日 水曜日 午後4時21分
■ Adding Security with a Tether
Tether Anchorage Points
A tether anchorage point is provided behind each rear seating position. A child seat that is installed with a seat belt and comes with a tether can use the tether for additional security.
Anchor
Outer Position
Cover
1. Locate the appropriate tether anchorage
point and lift the cover.
Tether Strap Hook
2. Raise the head restraint to its highest position, then route the tether strap through the head restraint legs. Make sure the strap is not twisted.
Center Position
Anchor
Tether Strap Hook
3. Secure the tether strap hook onto the
anchor.
4. Tighten the tether strap as instructed by the
child seat manufacturer.
Anchor
QRG
TOC
Index
Home
61
2013 Accord Sedan13 ACCORD 4D US-31T2A6000.book 62 ページ 2012年10月3日 水曜日 午後4時21分
uuChild SafetyuSafety of Larger Children
QRG
TOC
Safety of Larger Children ■ Protecting Larger Children The following pages give instructions on how to check proper seat belt fit, what kind of booster seat to use if one is needed, and important precautions for a child who must sit in front.
■ Checking Seat Belt Fit When a child is too big for a child seat, secure the child in a rear seat using the lap/ shoulder seat belt. Have the child sit upright and all the way back, then answer the following questions.
■ Checklist • Do the child's knees bend comfortably over
1Safety of Larger Children
3WARNING
Allowing a child age 12 or under to sit in front can result in injury or death if the passenger's front airbag inflates.
If a larger child must ride in front, move the vehicle seat as far to the rear as possible, have the child sit up properly and wear the seat belt properly, using a booster seat if needed.
the edge of the seat?
• Does the shoulder belt cross between the
child's neck and arm?
• Is the lap part of the seat belt as low as
possible, touching the child's thighs?
• Will the child be able to stay seated like this
for the whole trip?
If you answer yes to all these questions, the child is ready to wear the lap/shoulder seat belt correctly. If you answer no to any question, the child needs to ride on a booster seat until the seat belt fits properly without a booster seat.
Index
Home
62
2013 Accord SedanuuChild SafetyuSafety of Larger Children
1Booster Seats
When installing a booster seat, make sure to read the instructions that came with it, and install the seat accordingly.
There are high- and low-type booster seats. Choose a booster seat that allows the child to wear the seat belt correctly.
Some U.S. states and Canadian provinces and territories require children to use a booster seat until they reach a given age or weight (e.g. 6 years or 60 lbs). Be sure to check current laws in the state or province, or territory where you intend to drive.
13 ACCORD 4D US-31T2A6000.book 63 ページ 2012年10月3日 水曜日 午後4時21分
■ Booster Seats
If a lap/shoulder seat belt cannot be used properly, position the child in a booster seat in a rear seating position. For the child's safety, check that the child meets the booster seat manufacturer's recommendations.
■ Protecting Larger Children-Final Checks Your vehicle has a rear seat where children can be properly restrained. If you ever have to carry a group of children, and a child must ride in front: • Make sure you read and fully understand the instructions and safety information
in this manual.
• Move the front passenger seat as far back as possible.
• Have the child sit upright and well back in the seat.
• Check that the seat belt is properly positioned so that the child is secure in the
seat.
■ Monitoring child passengers We strongly recommend that you keep an eye on child passengers. Even older, more mature children sometimes need to be reminded to fasten their seat belts and sit up properly.
QRG
TOC
Index
Home
63
2013 Accord Sedan13 ACCORD 4D US-31T2A6000.book 64 ページ 2012年10月3日 水曜日 午後4時21分
Exhaust Gas Hazard
Carbon Monoxide Gas The engine exhaust from this vehicle contains carbon monoxide, a colorless, odorless, and highly toxic gas. As long as you properly maintain your vehicle, carbon monoxide gas will not get into the interior.
■ Have the exhaust system inspected for leaks whenever • The exhaust system is making an unusual noise.
• The exhaust system may have been damaged.
• The vehicle is raised for an oil change.
1Carbon Monoxide Gas
3WARNING Carbon monoxide gas is toxic. Breathing it can cause unconsciousness and even kill you.
Avoid any enclosed areas or activities that expose you to carbon monoxide.
When you operate a vehicle with the trunk open, airflow can pull exhaust gas into the interior and create a hazardous condition. If you must drive with the trunk open, open all the windows and set the heating and cooling system */climate control system * as shown below.
An enclosed area such as a garage can quickly fill up with carbon monoxide gas. Do not run the engine with the garage door closed. Even when the garage door is open, drive out of the garage immediately after starting the engine.
1. Select the fresh air mode.
2. Select the
mode.
3. Set the fan speed to high.
4. Set the temperature control to a comfortable setting.
Adjust the heating and cooling system */climate control system * in the same manner if you sit in your parked vehicle with the engine running.
* Not available on all models
QRG
TOC
Index
Home
64
2013 Accord Sedan13 ACCORD 4D US-31T2A6000.book 65 ページ 2012年10月3日 水曜日 午後4時21分
Safety Labels
Label Locations These labels are in the locations shown. They warn you of potential hazards that can cause serious injury or death. Read these labels carefully.
If a label comes off or becomes hard to read (except for the U.S. dashboard label which may be removed by the owner), contact a dealer for a replacement.
Sun Visor
U.S. models
Canadian models
Dashboard U.S. models only
Radiator Cap
Doorjambs
U.S. models
Canadian models
QRG
TOC
Index
Home
65
2013 Accord Sedan13 ACCORD 4D US-31T2A6000.book 66 ページ 2012年10月3日 水曜日 午後4時21分
QRG
Index
Home
66
2013 Accord Sedan13 ACCORD 4D US-31T2A6000.book 67 ページ 2012年10月3日 水曜日 午後4時21分
Instrument Panel
QRG
This chapter describes the buttons, indicators, and gauges that are used while driving.
* Not available on all models
Indicators ............................................ 68
Information Display Warning and
Information Messages*.................... 82
Multi-Information Display Warning and
Information Messages*.................... 84
Gauges and Displays
Gauges.............................................. 89
Information Display*.......................... 90
Multi-Information Display *................. 93
Index
Home
67
2013 Accord Sedan13 ACCORD 4D US-31T2A6000.book 68 ページ 2012年10月3日 水曜日 午後4時21分
Indicators
QRG
Indicator
Name
On/Blinking
Explanation
Message *
TOC
U.S.
Canada
Parking Brake and Brake System Indicator (Red)
U.S.
Canada
Brake System Indicator (Amber)
● Comes on for a few seconds when you turn the ignition switch to ON (w *1, then goes off.
● Comes on when the parking brake is applied, and goes off when it is released.
● Comes on when the brake fluid
level is low.
● Comes on if there is a problem
with the brake system.
● The beeper sounds and the
indicator comes on if you drive with the parking brake not fully released.
● Comes on for a few seconds when you turn the ignition switch to ON (w *1, then goes off.
● Comes on if there is a problem with the brake override system.
● Comes on while driving - Make sure
the parking brake is released. Check the brake fluid level.
2 What to do when the indicator
comes on P. 562
● Comes on along with the ABS
indicator - Have the vehicle checked by a dealer.
2 If the Brake System Indicator (Red)
Comes On P. 562
● Stays on constantly - Have the vehicle
checked by a dealer.
Index
Home
68
1:
Models
with the smart
entry system have an ENGINE START/STOP button instead of an ignition switch.
* Not available on all models
2013 Accord Sedan13 ACCORD 4D US-31T2A6000.book 69 ページ 2012年10月3日 水曜日 午後4時21分
uuIndicatorsu
Indicator
Name
On/Blinking
Explanation
Message *
Low Oil Pressure Indicator
● Comes on when you turn the
ignition switch to ON (w *1, and goes off when the engine starts. ● Comes on when the engine oil
pressure is low.
● Comes on while driving - Immediately
stop in a safe place.
2 If the Low Oil Pressure Indicator
Comes On P. 560
Malfunction Indicator Lamp
● Comes on when you turn the
● Readiness codes are part of the on board
ignition switch to ON (w *1, and goes off either when the engine starts or after several seconds if the engine is not started. If “readiness codes” have not been set, it blinks five times before it goes off.
● Comes on if there is a problem
with the emissions control system.
● Blinks when a misfire in the
engine's cylinders is detected.
diagnostics for the emissions control systems.
2 Testing of Readiness Codes P. 577
● Comes on while driving - Have the
vehicle checked by a dealer.
● Blinks while driving - Stop in a safe place where there are no flammable objects. Stop the engine for 10 minutes or more, and wait for it to cool down. Then, take the vehicle to a dealer.
2 If the Malfunction Indicator Lamp
Comes On or Blinks P. 561
● Comes on when you turn the
● Comes on while driving - Turn off the
Charging System Indicator
ignition switch to ON (w *1, and goes off when the engine starts.
● Comes on when the battery is not
charging.
heating and cooling system */climate control system * and rear defogger in order to reduce electricity consumption.
2 If the Charging System Indicator
Comes On P. 560
*1:
Models
with the smart
entry system have an ENGINE START/STOP button instead of an ignition switch.
* Not available on all models
QRG
TOC
Index
Home
Continued
69
2013 Accord SedanQRG
TOC
13 ACCORD 4D US-31T2A6000.book 70 ページ 2012年10月3日 水曜日 午後4時21分
uuIndicatorsu
Indicator
Name
On/Blinking
Explanation
Message *
Models with information display
Models with multi- information display
Shift Lever Position Indicator *
● Indicates in which position your
shift lever is.
2 Shifting P. 435
P. 437
P. 441
—
M (7-speed manual shift mode) Indicator/ Shift Indicator *
● Comes on when 7-speed manual
shift mode is applied.
2 7-Speed Manual Shift Mode P. 439
—
Index
Home
70
* Not available on all models
2013 Accord Sedan13 ACCORD 4D US-31T2A6000.book 71 ページ 2012年10月3日 水曜日 午後4時21分
uuIndicatorsu
Indicator
Name
On/Blinking
Explanation
Message *
● Blinks if the transmission system has
● Blinks while driving - Avoid sudden
a problem.
starts and acceleration and have the vehicle checked by a dealer immediately.
Models with information display
Models with multi- information display
Transmission Indicator *
QRG
TOC
Seat Belt Reminder Indicator
● Comes on and the beeper sounds if you are not wearing a seat belt when you turn the ignition switch to ON (w *1.
● If the front passenger is not wearing
a seat belt, the indicator comes on about six seconds later.
● Blinks while driving if either you or
● The beeper stops and the indicator goes off when you and the front passenger fasten their seat belts.
● Stays on after you or the front
passenger has fastened the seat belt - A detection error may have occurred in the sensor. Have the vehicle checked by a dealer.
the front passenger has not fastened a seat belt. The beeper sounds and the indicator blinks at regular intervals.
2 Seat Belt Reminder P. 33
*1:
Models
with the smart
entry system have an ENGINE START/STOP button instead of an ignition switch.
* Not available on all models
Index
Home
Continued
71
2013 Accord Sedan13 ACCORD 4D US-31T2A6000.book 72 ページ 2012年10月3日 水曜日 午後4時21分
uuIndicatorsu
QRG
TOC
Indicator
Name
On/Blinking
Explanation
Message *
Low Fuel Indicator
● Comes on when the fuel reserve is
● Comes on - Refuel your vehicle as soon
running low (approximately 2.6 U.S. gal./9.7 Liter left).
as possible.
● Blinks - Have the vehicle checked by a
● Blinks if there is a problem with the
dealer.
fuel gauge.
ABS (Anti-lock Brake System) Indicator
● Comes on for a few seconds when you turn the ignition switch to ON (w *1, then goes off.
● If it comes on at any other time, there is a problem with the ABS.
Supplemental Restraint System Indicator
● Comes on for a few seconds when you turn the ignition switch to ON (w *1, then goes off.
● Comes on if a problem with any of
the following is detected: - Supplemental restraint system - Side airbag system - Side curtain airbag system - Seat belt tensioner
● Stays on constantly - Have the vehicle checked by a dealer. With this indicator on, your vehicle still has normal braking ability but no anti-lock function.
2 ABS (Anti-lock Brake System)
P. 475
● Stays on constantly or does not come on at all - Have the vehicle checked by a dealer.
Index
Home
72
*1:
Models
with the smart
entry system have an ENGINE START/STOP button instead of an ignition switch.
* Not available on all models
2013 Accord Sedan13 ACCORD 4D US-31T2A6000.book 73 ページ 2012年10月3日 水曜日 午後4時21分
uuIndicatorsu
Indicator
Name
On/Blinking
Explanation
Message *
VSA® (Vehicle Stability Assist) System Indicator
● Comes on for a few seconds when you turn the ignition switch to ON (w *1, then goes off.
● Blinks when VSA® is active. ● Comes on if there is a problem with
the VSA® system or hill start assist system.
● Stays on constantly - Have the vehicle
checked by a dealer.
2 VSA® (Vehicle Stability Assist)
System P. 465
VSA® (Vehicle Stability Assist) OFF Indicator
● Comes on for a few seconds when you turn the ignition switch to ON (w *1, then goes off.
● Comes on when you deactivate
VSA®.
2 VSA® On and Off P. 466
—
QRG
TOC
*1:
Models
with the smart
entry system have an ENGINE START/STOP button instead of an ignition switch.
* Not available on all models
Index
Home
Continued
73
2013 Accord SedanQRG
TOC
13 ACCORD 4D US-31T2A6000.book 74 ページ 2012年10月3日 水曜日 午後4時21分
uuIndicatorsu
Indicator
Name
On/Blinking
Explanation
Message *
● Goes off when all doors and the trunk
are closed.
● Comes on for a few seconds if you turn the ignition switch to ON (w *1, then goes off.
● Comes on if any door or the trunk is
not completely closed.
● The beeper sounds and the indicator comes on if any door or the trunk is opened while driving.
Door and Trunk Open Indicator
Models with information display
Models with multi- information display
EPS (Electric Power Steering) System Indicator
● Comes on when you turn the
ignition switch to ON (w *1, and goes off when the engine starts.
● Comes on if there is a problem with
the EPS (Electric Power Steering) System.
● Stays on constantly or does not come on at all - Have the vehicle checked by a dealer.
2 If the EPS System Indicator Comes
On P. 562
Index
Home
74
*1:
Models
with the smart
entry system have an ENGINE START/STOP button instead of an ignition switch.
* Not available on all models
2013 Accord Sedan13 ACCORD 4D US-31T2A6000.book 75 ページ 2012年10月3日 水曜日 午後4時21分
uuIndicatorsu
Indicator
Name
On/Blinking
Explanation
Message *
Low Tire Pressure/ TPMS Indicator
● Comes on for a few seconds when you
turn the ignition switch to ON (w *1.
● May come on briefly if the ignition switch is turned to ON (w *1 and the vehicle is not moved within 45 seconds, to indicate the calibration process is not yet complete.
● Comes on and stays on when:
● Comes on while driving - Stop in a safe place, check tire pressures, and inflate the tire(s) if necessary.
● Stays on after the tires are inflated
to the recommended pressures - The
system needs to be calibrated.
2 TPMS Calibration P. 469
- One or more tires’ pressures are
determined to be significantly low. - The system has not been calibrated.
● Blinks for about one minute, and then stays on if there is a problem with the TPMS, or when a compact spare tire is temporarily installed.
● Blinks and remains on - Have the
vehicle checked by a dealer. If the vehicle is fitted with a compact spare, get your regular tire repaired or replaced and put back on your vehicle as soon as you can.
QRG
TOC
*1:
Models
with the smart
entry system have an ENGINE START/STOP button instead of an ignition switch.
* Not available on all models
Index
Home
Continued
75
2013 Accord Sedan13 ACCORD 4D US-31T2A6000.book 76 ページ 2012年10月3日 水曜日 午後4時21分
uuIndicatorsu
QRG
TOC
Index
Home
76
Indicator
Name
On/Blinking
Explanation
Message *
● Comes on for a few seconds when you set
● While the indicator is on, press the
the power mode to ON, then goes off. ● Comes on along with a beep when a
problem is detected. A system message on the multi-information display appears at the same time.
(information) button to see the
message again.
● Refer to the Indicators information in this chapter when a system message appears on the multi-information display. Take the appropriate action for the message.
● The multi-information display does not return
to the normal screen unless the warning is canceled, or the button is pressed.
● The turn signal indicators blink when you
● Does not blink or blinks rapidly - A
operate the turn signal lever.
● If you press the hazard warning button,
both indicators and all turn signals blink at the same time.
turn signal light bulb has blown. Change the bulb immediately.
2 Replacing Light Bulbs P. 518,
P. 520
● Comes on when the high beam headlights
are on.
—
System Message Indicator *
Turn Signal and Hazard Warning Indicators
High Beam Indicator
Lights On Indicator
● Comes on whenever the light switch is on,
or in AUTO when the exterior lights are on.
● If you remove the key from the ignition switch*1 while the exterior lights are on, a chime sounds when the driver's door is opened.
—
—
—
—
*1:
Models
with the smart
entry system have an ENGINE START/STOP button instead of an ignition switch.
* Not available on all models
2013 Accord Sedan13 ACCORD 4D US-31T2A6000.book 77 ページ 2012年10月3日 水曜日 午後4時21分
uuIndicatorsu
Indicator
Name
On/Blinking
Explanation
Message *
Fog Light Indicator *
● Comes on when the fog lights are
on.
—
● Comes on briefly when you turn the
● Blinks - You cannot start the engine.
ignition switch to ON (w *1, then goes off.
● Comes on if the immobilizer system
Immobilizer System Indicator
cannot recognize the key information.
Turn the ignition switch to LOCK (0 *1, pull the key out, and then insert the key and turn it to ON (w *1 again.
● Repeatedly blinks - The system may
be malfunctioning. Have the vehicle checked by a dealer.
● Do not attempt to alter this system or
add other devices to it. Electrical problems can occur.
Security System Alarm Indicator
Indicator
● Blinks when the security system
alarm has been set.
2 Security System Alarm P. 124
—
—
—
QRG
TOC
*1:
Models
with the smart
entry system have an ENGINE START/STOP button instead of an ignition switch.
* Not available on all models
Index
Home
Continued
77
2013 Accord SedanQRG
TOC
13 ACCORD 4D US-31T2A6000.book 78 ページ 2012年10月3日 水曜日 午後4時21分
uuIndicatorsu
Indicator
Name
On/Blinking
Explanation
Message*1
● Comes on for a few seconds when you change the power mode to ON, then goes off.
● Comes on when you have
customized FCW to turn off.
● Comes on if there is a problem
with the FCW system.
● Stays on constantly without FCW off - Have the vehicle
checked by a dealer.
Models with information display ● Blinks when the system detects a likely collision with a vehicle in front of you. The beeper sounds.
All models ● Comes on when the FCW
system shuts itself off.
Forward Collision Warning (FCW) Indicator *
● Blinks while driving - Take appropriate action to prevent
a collision (apply the brakes, change lanes, etc.).
Models with information display ● Stays on - The temperature inside the FCW system is too high.
The system activates when the temperature inside the system cools down.
2 Automatic shutoff P. 460
—
—
—
● Stays on - The radar sensor or the area around the camera is blocked by dirt, mud, etc. Stop your vehicle in a safe place, and wipe it off with a soft cloth.
● Have your vehicle checked by a dealer if:
Models with multi-information display The indicator and message stay on after you cleaned the radar sensor cover. Models with information display The indicator and message come back on after you cleaned the area around the camera.
2 Automatic shutoff P. 460
entry system have an ENGINE START/STOP button instead of an ignition switch.
Not
available
on
all
models
2 Automatic shutoff P. 460
—
—
Index
Home
78
*1:
Models
with the smart
2013 Accord Sedan13 ACCORD 4D US-31T2A6000.book 79 ページ 2012年10月3日 水曜日 午後4時21分
uuIndicatorsu
Indicator
Name
On/Blinking
Explanation
Message*1
● Comes on for a few seconds when you change the power mode to ON, then goes off.
● Comes on if there is a problem with
the LDW system.
● Stays on constantly - Have the vehicle
checked by a dealer.
Models with information display ● Blinks when your vehicle is too close to the lane lines. The beeper sounds.
● Blinks while driving - Take
appropriate action to keep your vehicle within the lane lines.
—
—
● Comes on when the LDW system
● Stays on - The temperature inside the
QRG
TOC
shuts itself off.
Lane Departure Warning (LDW) Indicator *
LDW camera is too high. The system activates when the temperature inside the camera cools down.
2 LDW Camera P. 463
● Stays on - The area around the camera is blocked by dirt, mud, etc. Stop your vehicle in a safe place, and wipe it off with a soft cloth.
● Have your vehicle checked by a dealer if
the indicator and message come back on after you cleaned the area around the camera.
2 LDW Camera P. 463
*1:On the left: Models with information display On the right: Models with multi-information display
* Not available on all models
Index
Home
Continued
79
2013 Accord SedanQRG
TOC
13 ACCORD 4D US-31T2A6000.book 80 ページ 2012年10月3日 水曜日 午後4時21分
uuIndicatorsu
Indicator
Name
On/Blinking
Explanation
Message *
ACC (Adaptive Cruise Control) Indicator (Amber) *
ECON Mode Indicator
● Comes on for a few seconds when you change the power mode to ON, then goes off.
● Comes on if there is a problem with
ACC.
● Comes on when you turn the
ignition switch to ON (w *1, and goes off when the engine starts.
● Comes on when you press the
ECON button.
● Comes on while driving - Have the
vehicle checked by a dealer.
2 ECON Button P. 446
CRUISE MAIN Indicator *
● Comes on when you press the
CRUISE button.
2 Cruise Control* P. 447
CRUISE CONTROL Indicator *
Washer Level Indicator *
● Comes on if you have set a speed for
cruise control.
2 Cruise Control* P. 447
● Comes on when the washer fluid
● Refill the washer fluid.
gets low.
2 Refilling Window Washer Fluid
P. 512
2 Maintenance MinderTM P. 489
Maintenance Minder Indicator *
● Comes on when the scheduled
maintenance is due soon.
—
—
—
—
Index
Home
80
*1:
Models
with the smart
entry system have an ENGINE START/STOP button instead of an ignition switch.
* Not available on all models
2013 Accord Sedan13 ACCORD 4D US-31T2A6000.book 81 ページ 2012年10月3日 水曜日 午後4時21分
uuIndicatorsu
Indicator
Name
On/Blinking
Explanation
Message *
● Comes on for a few seconds when you change the power mode to ON. ● Comes on as soon as a problem is detected in the smart entry system or push button starting system.
Smart Entry System Indicator *
● Have your vehicle checked by a dealer.
U.S.
Canada
Starter System Indicator *
● Comes on for a few seconds when
you set the power mode to ON, then goes off.
● Comes on if the starting system has
a problem.
● As a temporary measure, press and hold the ENGINE START/STOP button for 15 seconds while pressing the brake pedal and manually start the engine. Have the vehicle checked by a dealer.
Light Control Indicator *
● Comes on if there is a problem with
the automatic lighting control system or low beam headlights *.
● Comes on while driving - Turn the lights on manually and have the vehicle checked by a dealer.
*1:
Models
with the smart
entry system have an ENGINE START/STOP button instead of an ignition switch.
* Not available on all models
QRG
TOC
—
—
Index
Home
81
2013 Accord Sedan13 ACCORD 4D US-31T2A6000.book 82 ページ 2012年10月3日 水曜日 午後4時21分
uuIndicatorsuInformation Display Warning and Information Messages*
QRG
Information Display Warning and Information Messages* The following messages appear only on the information display.
Message
Condition
Explanation
● Appears when the fuel fill cap is loose or is not
installed.
2 Check/Tighten Fuel Cap Message P. 561
TOC
● Appears when there is a problem with the sensor on
● Stays on constantly - Have the vehicle checked by a
the battery.
dealer.
Index
Home
82
* Not available on all models
2013 Accord Sedan13 ACCORD 4D US-31T2A6000.book 83 ページ 2012年10月3日 水曜日 午後4時21分
uuIndicatorsuInformation Display Warning and Information Messages*
Models with smart entry system
Message
Condition
Explanation
● Appears if you push the ENGINE START/STOP button
● Push the ENGINE START/STOP button twice after
to turn the engine off without the shift lever in (P.
moving the shift lever to (P.
QRG
TOC
● Appears when the power mode is in ACCESSORY.
—
● Appears when the steering wheel is locked.
● Move the steering wheel left and right while pressing
the ENGINE START/STOP button at the same time.
● Appears when you close the door with the power mode in ON without the smart entry remote inside the vehicle.
● Disappears when you bring the smart entry remote back
inside the vehicle and close the door.
● Appears when the smart entry remote’s battery
becomes weak.
● Replace the battery as soon as possible.
2 Replacing the Button Battery P. 535
* Not available on all models
Index
Home
83
2013 Accord Sedan13 ACCORD 4D US-31T2A6000.book 84 ページ 2012年10月3日 水曜日 午後4時21分
uuIndicatorsuMulti-Information Display Warning and Information Messages*
Multi-Information Display Warning and Information Messages* The following messages appear only on the multi-information display. Press the with the system message indicator on.
(information) button to see the message again
Message
Condition
Explanation
● Appears when the fuel fill cap is loose or is not
installed.
2 Check/Tighten Fuel Cap Message P. 561
● Appears when the scheduled maintenance is due
soon. uConsequently, Maintenance Due Now and
Maintenance Past Due follow.
● Appears when the engine coolant temperature gets
abnormally high.
2 Maintenance Minder Messages on the Multi-
Information Display P. 494
2 Overheating P. 558
● Appears if there is a problem with the automatic
● Comes on while driving - Manually turn the lights on,
lighting control system.
and have your vehicle checked by a dealer.
● Appears if there is a problem with the low beam
● Comes on while driving - Turn the lights on manually
headlights.
and have the vehicle checked by a dealer.
* Not available on all models
QRG
TOC
Index
Home
84
2013 Accord Sedan13 ACCORD 4D US-31T2A6000.book 85 ページ 2012年10月3日 水曜日 午後4時21分
uuIndicatorsuMulti-Information Display Warning and Information Messages*
Message
Condition
Explanation
● Appears while you are customizing the settings and
the shift lever is moved out of (P.
2 Customized Features P. 97
● Appears after you unlock and open the driver’s door.
2 Starting the Engine P. 429
● Appears three seconds after the To Start Engine
message appears.
2 Starting the Engine P. 429
QRG
TOC
● Appears when the steering wheel is locked.
● Move the steering wheel left and right after pressing
the ENGINE START/STOP button.
● Appears if you push the ENGINE START/STOP
● Push the ENGINE START/STOP button twice after
button to turn the engine off without the shift lever in (P.
moving the shift lever to (P.
* Not available on all models
Index
Home
Continued
85
2013 Accord Sedan13 ACCORD 4D US-31T2A6000.book 86 ページ 2012年10月3日 水曜日 午後4時21分
uuIndicatorsuMulti-Information Display Warning and Information Messages*
QRG
TOC
Message
Condition
● Appears when the power mode is in ACCESSORY.
Explanation
—
Index
Home
86
● Appears after the driver’s door is opened when the
power mode is in ACCESSORY.
● Press the ENGINE START/STOP button twice with your foot off the brake pedal to change the power mode to VEHICLE OFF (LOCK).
● Appears when you close the door with the power mode in ON without the smart entry remote inside the vehicle.
● Disappears when you bring the smart entry remote