1997 Honda Accord Sedan Owners Manual

locks the steering. This can cause you to lose control.

Remove the key from the ignition switch only when parked.

Instruments and Controls

ACCESSORY (I) — In this position, you can operate the audio system and the cigarette lighter.

ON (II) — This is the normal key position when driving. All features and accessories on the car are usable. Several of the lights on the instru- ment panel come on as a test when you turn the ignition switch from ACCESSORY to ON (see page 35).

START (III) — Use this position only to start the engine. The switch returns to ON (II) when you let go of the key.

You will hear a reminder beeper if you leave the key in the ignition switch in the LOCK (0) or ACCESSORY (I) position and open the driver's door. Remove the key to turn off the beeper.

Door Locks

LOCK TAB

The front doors can be locked and unlocked from the outside with the key.

Power Door Locks

MASTER DOOR LOCK SWITCH

Keys and Locks

Each door has a lock tab on the top. Push the tab down to lock the door and pull it up to unlock.

To lock any passenger's door when getting out of the car, push the lock tab down and close the door. To lock the driver's door, pull the outside door handle and push the lock tab down. Release the handle, then close the door.

On all models except U.S. DX and Canadian LX models Each front door has a master door lock switch. Either switch locks and unlocks all doors. Push the switch down to lock all doors, and up to unlock them.

CONTINUED

Instruments and Controls

Keys and Locks

To lock any passenger's door when getting out of the car, push the lock tab in and close the door. To lock the driver's door, pull the outside door handle and push the lock tab in or push the master switch down. Release the handle, then close the door.

All doors can be locked from the outside by using the key in either front door. To unlock only the driver's door from the outside, insert the key in the driver's door lock, turn the key and release it. If you turn the key and hold it, all doors will unlock. All four doors will unlock when you unlock the passenger's door with the key.

Instruments and Controls

Remote Transmitter

LED

LOCK BUTTON

UNLOCK BUTTON

PANIC BUTTON

On U.S. Special Edition model You can lock and unlock your vehicle with the remote transmitter. When you push the LOCK button, all doors lock. When you push the UNLOCK button once, only the driver's door unlocks. The remaining doors unlock when you push the button a second time.

The ceiling light (if the ceiling light switch is in the center position) will come on when you press the UNLOCK button. If you do not open any of the doors, the light will go out in about 30 seconds and the doors will automatically relock. If you relock the doors with the remote transmitter before 30 seconds have elapsed, the light will go off immediately.

You cannot lock or unlock the doors with the remote transmitter if any door is not fully closed or the key is in the ignition switch. If any door is not closed, the horn sounds three times to alert you.

To turn the audible signal off, repeat the above procedure. You should see the LED blink twice.

The audible signal feature will be off after you install a new battery in the remote transmitter. Use the above procedure to turn it on again.

Audible Signal Operation The system will signal you when the doors lock and unlock by flashing the parking lights, side marker lights and taillights: once when the doors lock; and twice when they unlock. You can program the remote transmitter so the horn will also sound. The horn will sound once when you lock the doors, and twice when you unlock them.

To turn audible signal on, press and hold the LOCK and UNLOCK buttons at the same time. You should see the LED on the remote transmitter come on for one second. Release both buttons after the LED goes out.

Keys and Locks

Panic Mode Panic mode allows you to remotely activate your vehicle's security system to attract attention. When activated, the alarm will sound and the exterior lights will flash for about two minutes. To activate panic mode, push and hold the PANIC button for about one second.

To cancel panic mode before two minutes, press any button on the remote transmitter. You can also turn the ignition switch to ON (II).

Panic mode will not activate if the key is in the ignition switch.

CONTINUED

Instruments and Controls

Keys and Locks

Replacing the Battery When the remote transmitter's battery begins to get weak, it may take several pushes on the button to lock or unlock the doors, and the LED will not light. Replace the battery as soon as possible.

Battery type: CR2025

Instruments and Controls

Open

Close

To replace the battery, remove the round cover on the back of the trans- mitter by turning it counterclockwise with a coin.

BATTERY

ROUND COVER

CUSHION RING

Remove the old battery and note the polarity. Make sure the polarity of the new battery is the same (+ side facing up), then insert it in the transmitter.

Reinstall the cushion ring. Align the mark on the cover with the mark on the transmitter,

then set the cover in place and turn it clockwise.

After the battery is changed, the transmitter must be synchronized with the main unit. With the doors closed, press either the LOCK or UNLOCK button six times.

Transmitter Care Avoid severe shock to the trans- mitter, such as dropping or throwing it. Also, protect it from extreme hot or cold temperatures.

Clean the transmitter case with a soft cloth. Do not use strong cleaners or solvents that could harm the case. Immersing the transmitter in any liquid will harm the trans- mitter and cause it to not function properly.

If you lose a transmitter, you will need to have the replacement programmed to your car's system by your Honda dealer. Any other transmitters you have will also need to be reprogrammed.

Keys and Locks

As rquired by FCC: This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

Instruments and Controls

Keys and Locks

Childproof Door Locks

Trunk

LEVER

TRUNK RELEASE HANDLE

MASTER KEY

You can open the trunk in two ways:

Pull the trunk release handle to the left of the driver's seat.

Use the master key to open the trunk lock. The valet key does not work in this lock.

To close the trunk, press down on the trunk lid.

See page 135 for cargo loading and weight limit information. Keep the trunk lid closed at all times while driving to avoid damaging the lid, and to prevent exhaust gas from getting into the interior. See Carbon Monoxide Hazard on page 29.

The childproof door locks are designed to prevent children seated in the rear from accidentally opening the rear doors. Each rear door has a lock lever near the edge. With the lever in the LOCK position, the door cannot be opened from the inside regardless of the position of the lock tab. To open the door, pull the lock tab up and use the outside door handle.

Instruments and Controls

Glove Box

Keys and Locks

An open glove box can cause serious injury to your passenger in a crash, even if the passenger is wearing the seat belt.

Always keep the glove box closed while driving.

MASTER KEY To protect items in the trunk when you need to give the key to someone else:

1. Lock the trunk release handle

with the master key.

2. Give the person the valet key.

GLOVE BOX

Open the glove box by pulling the bottom of the handle. Close it with a firm push. Lock or unlock the glove box with the master key.

The glove box light comes on only when the instrument panel lights are on.

Instruments and Controls

Seat Adjustments

All V-6 models and the 4-cylinder EX model with leather interior in the U.S. have power adjustments for the seat bottom. The EX V-6 model in the U.S. and the EX-R V-6 model in Canada also have a power adjustment for the seat-back angle.

The 4-cylinder EX model without leather interior in the U.S., and the EX-R model in Canada have a power seat bottom height adjustment. All other seat adjustments in these models are manual.

The 4-cylinder DX, LX and Special Edition models in the U.S., and the LX, EX and Special Edition models in Canada have manual seat adjust- ments (see next column).

The front passenger's seat in all Accord models adjusts manually.

Instruments and Controls

Front Seat Adjustments

Adjust the seat before you start driving.

To adjust the seat forward and backward, pull up on the lever under the seat cushion's front edge. Move the seat to the desired position and release the lever. Try to move the seat to make sure it is locked in position.

To change the angle of the seat-back, pull up on the lever on the outside of the seat bottom. Move the seat-back to the desired position and release the lever. Let the seat-back latch in the new position.

Driver's Seat Power Height Adjustment

Reclining the seat-back can decrease the protection you get from your seat belt in a crash.

You can slide under the seat belt and be seriously injured.

Adjust the seat-back to an upright position and sit well back in the seat.

On EX model in the U.S., and EX-R models in Canada The height of your driver's seat is power adjustable. Pull up on the switch to raise the seat. Push it down to lower the seat.

Adjust the seat before you start driving.

Seat Adjustments

Driver's Seat Power Seat Bottom Adjustments On LX V-6 model and 4-cylinder EX model with leather interior in the U.S. The position of the driver's seat bottom is power adjustable. Use the horizontal switch on the outside of the seat bottom.

To change the seat-back angle, use the manual adjustment lever on the outside edge of the seat bottom (see page 60).

Adjust the seat before you start driving.

CONTINUED

Instruments and Controls

Seat Adjustments

Push the switch forward or backward to adjust the distance to the steering wheel and pedals.

Pull up or push down on the front of the switch to move the seat bottom's front edge up or down. Pull up or push down on the rear of the switch to move the rear of the seat bottom up or down.

Pull the center of the switch up to raise the seat. Push it down to lower the seat.

Instruments and Controls

Driver's Seat Full Power Adjustments On EX V-6 model in the U.S., and EX-R V-6 model in Canada The two power seat adjustment switches are on the outside edge of the seat bottom. The horizontal switch adjusts the seat bottom in several directions. The short vertical switch adjusts the seat-back angle.

Adjust the seat before you start driving.

Seat Adjustments

Push the horizontal switch forward or backward to adjust the distance to the steering wheel and pedals.

Pull up or push down on the front of the switch to move the seat bottom's front edge up or down. Pull up or push down on the rear of the switch to move the rear of the seat bottom up or down.

CONTINUED

Instruments and Controls

Seat Adjustments

Pull the center of the horizontal switch up to raise the seat. Push it down to lower the seat.

Adjust the seat-back angle by pushing the rear switch in the direction you want to move.

Instruments and Controls

Reclining the seat-back can decrease the protection you get from your seat belt in a crash.

You can slide under the seat belt and be seriously injured.

Adjust the seat-back to an upright position and sit well back in the seat.

Driver's Lumbar Support

Head Restraints

On EX, EX V-6 models in the U.S., and EX-R, EX-R V-6 models in Canada Vary the lumbar support by moving the lever on the right side of the seat-back. Pivot the lever forward until it stops, then let it return. Doing this several times adjusts the lumbar support through its full range.

RELEASE BUTTON

The front head restraints help protect you and your passenger from whiplash and other injuries. They are most effective when you adjust them so the top of the restraint is even with the top of your ears.

Seat Adjustments

The front head restraints adjust for height. You need both hands to adjust the restraint. Do not attempt to adjust it while driving. To raise it, pull upward. To lower the restraint, push the release button sideways and push the restraint down.

CONTINUED

Instruments and Controls

Seat Adjustments

To remove a head restraint for cleaning or repair, pull it up as far as it will go. Push the release button and pull the restraint out of the seat- back.

Folding Rear Seat

MASTER KEY

Driving your car without head restraints can lead to serious injury to you and your passenger in a crash.

Make sure the head restraints are in place and adjusted properly before driving.

The back of the rear seat folds down, giving you direct access to the trunk. The seat-back can be released from inside the car or inside the trunk.

To fold down the seat-back from inside the car, insert the master key in the lock on the rear shelf. Turn the key clockwise, pull down the top of the seat-back, then release the key.

Instruments and Controls

Seat Adjustments

Pull

Make sure both rear shoulder belts are positioned in front of the rear seat-back whenever the seat-back is in its upright position.

Never drive with the seat-back folded down and the trunk lid open. See Carbon Monoxide Hazard on page 29 .

Make sure all items in the trunk, or items extending through the opening into the back seat, are tied down. Loose items can fly forward and cause injury if you have to brake hard. See Loading Cargo on page 135.

To release the seat-back from inside the trunk, pull the release loop under the rear shelf.

To lock the seat-back upright, push it firmly against the rear shelf. Make sure it is latched in place by pulling on the top of the seat.

Instruments and Controls

Seat Adjustments

Rear Seat Armrest On all models except U.S. DX and Canadian LX models

Trunk Pass-through Cover

KNOB

For security, this cover can be locked and unlocked only with the master key. To lock the cover, insert the key and turn it clockwise.

Never drive with this cover open, especially if the trunk lid is also open. See Carbon Monoxide Hazard on page 29.

LID

The cover behind the rear seat armrest allows you to reach small objects in the trunk from the interior.

The pass-through cover can be opened from either side; it folds forward onto the center armrest. Open the cover by sliding the knob downward and pulling on the cover. To close the cover, swing it up and push firmly on the top. Make sure it latches properly.

The rear seat armrest is located at the center of the rear seat. Pivot it down to use it.

Instruments and Controls

On all models except U.S. DX and Canadian LX models Your car's windows are electrically- powered. Turn the ignition switch to ON (II) to raise or lower any window.

Each door has a switch that controls its window. To open the window, push the switch down and hold it. Release the switch when you want the window to stop. Close the window by pushing the switch up and holding it.

DRIVER'S WINDOW SWITCH

MAIN SWITCH

The driver's armrest has a master power window control panel. To open any of the passengers' windows, push down on the appropriate switch and hold it down until the window reaches the desired position. To close the window, push up on the window switch. Release the switch when the window gets to the position you want.

Power Windows

Closing a power window on a child's hands or fingers can cause serious injury.

Make sure your children are away from the windows before closing them.

CONTINUED

Instruments and Controls

Power Windows, Moonroof

The master control panel also con- tains these extra features: AUTO — To open the driver's window fully, push the window switch firmly down and release it. The window automatically goes all the way down. To stop the window from going all the way down, push the window switch up briefly.

To open the driver's window only partially, push the window switch down lightly and hold it. The window will stop as soon as you release the switch.

The AUTO function only works to lower the driver's window. To raise the window, you must push the window switch up and hold it until the window reaches the desired position.

Instruments and Controls

The MAIN switch controls power to the passengers' windows. With this switch off, the passengers' windows cannot be raised or lowered. The MAIN switch does not affect the driver's window. Keep the MAIN switch off when you have children in the car so they do not injure them- selves by operating the windows unintentionally.

The power window system has a key- off delay function. The windows will still operate for up to ten minutes after you turn off the ignition. Opening either front door cancels the delay function. You must turn the ignition ON (II) again before you can raise or lower the windows.

Moonroof

ROOF

MOONROOF SWITCH

On Special Edition, EX, EX V-6 models in the U.S., and Special Edition, EX-R, EX-R V-6 models in Canada Use the switch on the dashboard to open and close the moonroof. The ignition must be ON (II). Push and hold the switch to open the moonroof. Release the switch when the moonroof reaches the desired position. To close the moonroof, press and hold the

switch.

The moonroof has a key-off delay. You can still open and close the moonroof for up to ten minutes after you turn off the ignition. The key-off delay cancels as soon as you open either front door. You must then turn the ignition ON (II) for the moonroof to operate.

Closing the moonroof on someone's hands or fingers can cause serious injury.

Make sure passengers are clear of the moonroof before closing it.

Moonroof, Mirrors

NOTICE

Mirrors

If you try to open the moonroof in below-freezing temperatures, or when it is covered with snow or ice, you can damage the moonroof panel or motor.

TAB

Keep the inside and outside mirrors clean and adjusted for best visibility. Be sure to adjust the mirrors before you start driving.

The inside mirror has day and night positions. The night position reduces glare from headlights behind you. Flip the tab on the bottom edge of the mirror to select the day or night position.

CONTINUED

Instruments and Controls

Mirrors

Adjusting the Power Mirrors

SELECTOR SWITCH

1. Turn the ignition switch ON (II).

2. Move the selector switch to L

(driver's side) or R (passenger's side).

On all models except U.S. DX and Canadian LX models Adjust the outside mirrors with the adjustment switch on the driver's door armrest:

Instruments and Controls

ADJUSTMENT SWITCH

3. Push the appropriate edge of the

adjustment switch to move the mirror right, left, up or down.

4. When you finish, move the

selector switch to the center (off) position. This turns off the adjustment switch so you can't move a mirror out of position by accidentally bumping the switch.

Parking Brake

NOTICE

Driving the car with the parking brake applied can damage the rear brakes and axles.

PARKING BRAKE LEVER

To apply the parking brake, pull the lever up fully. To release it, pull up slightly, push the button, and lower the lever. The parking brake light on the instrument panel should go out when the parking brake is fully released (see page 36). If you try to drive the car without releasing the parking brake, the ABS indicator may come on, and ABS may not work properly.

Instruments and Controls

Digital Clock

RESET

The digital clock displays the time with the ignition switch ON (II). To see the time with the ignition off, press and hold the wide button under the clock.

To set the clock:

1. Turn the ignition switch ON (II) to

display the time.

2. Swing down the front cover of the

wide button under the clock display. You will see H, M, and RESET buttons.

Instruments and Controls

3. Press and hold the H button until the hour advances to the desired time.

4. Press and hold the M button until

the numbers advance to the desired time.

You can use the RESET button to quickly set the time to the nearest hour. If the displayed time is before the half hour, pressing RESET sets the clock back to the previous hour. If the displayed time is after the half hour, pressing RESET sets the clock forward to the beginning of the next hour. For example:

1:06 would RESET to 1:00. 1:52 would RESET to 2:00.

Beverage Holder, Vanity Mirror

Beverage Holder

Vanity Mirror

Push

To open the beverage holder, push on the top. The beverage holder lid is spring-loaded and will swing open. To close it, push it down until it latches. Use the beverage holder only when the car is parked. If you place cups in the holder while driving, the liquid may spill when you go over bumps or around corners. The inner liner can be removed if you want to hold a larger cup.

Be careful when you are using the beverage holder. A spilled liquid that is very hot can scald you or your passenger. Spilled liquids can also damage the upholstery, carpeting, and electrical components in the interior.

To use a vanity mirror on the back of the sun visor, pull down the cover.

Some U.S. models and the Canadian LX models have lighted vanity mirrors.

The light beside the mirror comes on only when the light switch is turned on.

Instruments and Controls

Cigarette Lighter, Ashtrays

Cigarette Lighter

Ashtrays

CIGARETTE LIGHTER

The ignition switch must be in ACCESSORY (I) or ON (II) for the cigarette lighter to work. To heat up the lighter, push it in. It will pop out when it is ready for use. Do not hold the lighter in while it is heating up, you could cause it to overheat.

ASHTRAY

Open the front ashtray by swinging the lid down. To remove the ashtray for emptying, open the lid then pull the ashtray straight outward.

Instruments and Controls

ASHTRAY

The rear ashtray is at the rear end of the center console. Open the ashtray by swinging the upper edge of the lid down. To remove the ashtray for emptying, open it, then lift up and out.

NOTICE

Use the ashtray only for cigarettes, cigars, and other smoking materials. To prevent a possible fire and damage to your car, don't put paper or other things that can burn in the ashtray.

Ceiling Light

OFF

ON

DOOR ACTIVATED

The ceiling light has a three-position switch. In the OFF position, the light does not come on. In the center position, the ceiling light comes on when you open any door. In the ON position, the ceiling light stays on continuously.

On Special Edition model in the U.S. The ceiling light (with the switch in the center position) also comes on when you unlock the door with the remote transmitter (see page 54 ).

On all models except U.S. DX and Canadian LX models Turn on the spotlight by pushing the button next to each light. Push the button again to turn it off. You can use the spotlights at all times.

Interior Lights

Courtesy Lights

IGNITION SWITCH LIGHT

DOOR LIGHT

On all models except U.S. DX and Canadian LX models Each door has a courtesy light. This light comes on when you open any door. Your car also has a courtesy light in the ignition switch. This light comes on when you open the driver's door. It remains on for several seconds after the door is closed.

Instruments and Controls

Comfort and Convenience Features

The heating and air conditioning* systems in your Honda provide a comfortable driving environment in all weather conditions.

* Air conditioning is optional on the U.S. DX model.

The standard audio system has many features. This section de- scribes those features and how to use them. (If you selected an optional audio system, refer to the operating instructions that came with it.)

* Audio sound system is optional on some U.S. DX models.

On Special Edition model in the U.S. The security system helps to dis- courage vandalism and theft of your Honda.

Heating and Cooling........................ 80
What Each Control Does............ 80
How to Use the System............... 82
To Turn Everything Off ............. 86
Audio System (Canadian LX)......... 87
Operating the Radio.................... 88
Adjusting the Sound.................... 90
Operating the Cassette Player... 91
Tape Search Functions............... 92

Audio System

(Except Special Edition, U.S. DX and Canadian LX)............. 93
Operating the Radio.................... 94
Adjusting the Sound.................... 97
Audio System Lighting............... 97
Operating the Cassette Player... 98
Caring for Cassettes.................. 100
Operating the Optional CD

Changer.................................. 101
Protecting Compact Discs........ 103
CD Changer Error

Indications.............................. 104

Audio System (Special Edition)... 105
Operating the Radio.................. 106
Adjusting the Sound.................. 109
Radio Frequencies..................... 110
Radio Reception......................... 110
Operating the CD Player.......... 112
Operating the CD Changer...... 114
Protecting Compact Discs........ 115
CD Player Error Indications..... 116
CD Changer Error

Indications.............................. 117

Operating the Cassette

Player...................................... 118
Tape Search Functions............. 119
Caring for the Cassette

Player...................................... 121
Theft Protection........................ 122
Security System............................. 123

Comfort and Convenience Features

Heating and Cooling

Proper use of the Heating and Cooling system can make the interior dry and comfortable, and keep the windows clear for best visibility.

If your vehicle does not have air conditioning, it can be installed at any time. Your dealer will install a Genuine Honda air conditioning system that meets Honda's high quality standards and is designed to exactly fit your vehicle. Please contact your dealer for more information.

What Each Control Does

Fan Control Dial Turning this dial clockwise increases the fan's speed, which increases air flow.

Temperature Control Dial Turning this dial clockwise increases the temperature of the air flow.

Comfort and Convenience Features

FRESH AIR/RECIRCULATION BUTTON

AIR CONDITIONING BUTTON

FAN CONTROL DIAL

TEMPERATURE CONTROL DIAL

MODE BUTTONS

Air Conditioning (A/C) Button This button turns the air condi- tioning ON and OFF. The indicator above the button lights when the A/C is on.

side air is

Fresh Air/Recirculation Button This button controls the source of the air going into the system. When you select the brought in from outside the vehicle (Fresh Air mode). When you select the interior is sent through the system again (Recirculaton mode). The indicator light shows which mode is selected.

side air from the vehicle's

Mode Buttons Use the MODE buttons to select the vents the air flows from.

Air flows from the center

and corner vents in the dashboard.

Air flow is divided between the vents in the dashboard and the floor vents.

Air flows from the floor

vents.

Air flow is divided between

the floor vents and the defroster vents at the base of the windshield.

Air flows from the defroster vents at the base of the windshield.

Heating and Cooling

Comfort and Convenience Features

Heating and Cooling

Vent Controls

CENTER VENT

SIDE VENT

You can adjust the direction of the air coming from the dashboard vents by moving the tab in the center of each vent up-and-down and side-to- side.

The vents in the corners of the dashboard can be opened and closed with the dials next to them.

Comfort and Convenience Features

How to Use the System This section covers how to set up the system controls for ventilation, heating, cooling, dehumidifying, and defrosting.

The engine must be running for the heater and air conditioning to generate hot and cold air. The heater uses engine coolant to warm the air. If the engine is cold, it will be several minutes before you feel warm air coming from the system. The air conditioning does not rely on engine temperature.

It is best to leave the system in mode under almost all

conditions. Keeping the system in mode, particularly with the A/C off, can cause the windows to fog up. Switch to you are driving through smoky or dusty conditions, then switch back to

mode when

mode when the condition

clears.

The outside air intakes for the heating and cooling system are at the base of the windshield. Keep these clear of leaves and other debris.

Heating and Cooling

RECIRCULATION/FRESH AIR BUTTON

AIR CONDITIONING BUTTON

FAN CONTROL DIAL

TEMPERATURE CONTROL DIAL

MODE BUTTONS

Ventilation The flow-through ventilation system draws in outside air, circulates it through the interior, then exhausts it through vents near the rear window.

1. Turn the temperature control dial

all the way to the left. Make sure the A/C is off.

2. Select 3. Set the fan to the desired speed.

and

CONTINUED

Comfort and Convenience Features

Heating and Cooling

To Cool with A/C 1. Turn on the A/C by pressing the

button. The light above the button should come on.

2. Make sure the temperature

control dial is all the way to the left.

3. Select 4. Set the fan to the desired speed.

and

If the interior is very warm from being parked in the sun, you can cool it down more rapidly by setting up the controls this way:

1. Start the engine. 2. Turn on the A/C by pressing the button. Make sure the tempera- ture control dial is all the way to the left.

3. Set the fan to maximum speed. 4. Open the windows partially. Select

and

Comfort and Convenience Features

FRESH AIR/RECIRCULATION BUTTON

AIR CONDITIONING BUTTON

FAN CONTROL DIAL

TEMPERATURE CONTROL DIAL

MODE BUTTONS

When the interior has cooled down to a more comfortable temperature, close the windows and set the controls as described for normal cooling.

Air conditioning places an extra load on the engine. Watch the engine coolant temperature gauge (see page 40) when driving in stop-and-go traffic or climbing a long, steep hill. If it moves near the red zone, turn off the A/C until the gauge reads normally.

To Heat To warm the interior:

1. Start the engine. 2. Select 3. Set the fan to the desired speed. 4. Adjust the warmth of the air with

and

the temperature control lever.

To Heat and Dehumidify with Air Conditioning Air conditioning, as it cools, removes moisture from the air. When used in combination with the heater, it makes the interior warm and dry.

1. Switch the fan on. 2. Turn on the air conditioning. 3. Select 4. Adjust the temperature control

and

dial so the mixture of heated and cooled air feels comfortable.

Heating and Cooling

To Defog and Defrost To remove fog from the inside of the windows:

1. Switch the fan on. 2. Turn on the air conditioning. 3. Select 4. Adjust the temperature control

and

dial so the air flow from the defroster vents feels warm.

5. Turn on the rear window defogger

to help clear the rear window.

This setting is suitable for all driving conditions whenever the outside temperature is above 32° F (0°C).

CONTINUED

Comfort and Convenience Features

These settings direct all the air flow to the defroster vents at the base of the windshield and the side window defroster vents. The air flow will get warmer and clear the windows faster as the engine warms up. You can close the side vents with the dial beside each vent. This will send more warm air to the windshield defroster vents.

For safety, make sure you have a clear view through all the windows before driving away.

To Turn Everything Off To shut off the system temporarily, turn the fan speed and temperature control dial all the way to the left.

You should shut the system com- pletely off only for the first few minutes of driving in cold weather, until the engine coolant warms up enough to operate the heater. Keep the fan on at all other times so stale air does not build up in the interior.

Heating and Cooling

To remove exterior frost or ice from the windshield and side windows after the car has been sitting out in cold weather:

1. Start the engine. 2. Select 3. Switch the fan and temperature

and

controls to maximum.

To rapidly remove exterior frost or ice from the windshield (on very cold days), first select windshield is clear, select avoid fogging the windows.

Once the to

Comfort and Convenience Features

Audio System

SW-VOL/BAL KNOB

TUNE/SEEK BAR

AM/FM/Cassette Stereo Audio System For Canadian LX model only Your Honda's audio system provides clear reception on both AM and FM bands, while the preset buttons allow you to easily select your favorite stations.

The cassette system features autoreverse for continuous play.

AM/FM BUTTON

PRESET BUTTONS

Comfort and Convenience Features

SW-VOL/BAL KNOB

TUNE/SEEK BAR

STEREO INDICATOR

AM/FM BUTTON

PRESET BUTTONS

Audio System

Operating the Radio The ignition switch must be in ACCESSORY (I) or ON (II) to operate the audio system. Turn the system on by pushing the SW-VOL/ BAL knob.

Adjust the volume by turning the SW-VOL/BAL knob.

The band and frequency that the radio was last tuned to is displayed. To change bands, press the AM/FM button. On the FM band, ST will be displayed if the station is broadcast- ing in stereo. Stereo reproduction on AM is not available.

Comfort and Convenience Features

You can use any of three methods to find radio stations on the selected band: TUNE, SEEK, or the Preset buttons.

) to tune to a higher frequency,

TUNE — Use the TUNE/SEEK bar to tune the radio to a desired frequency. Press the upper part or the lower part ( lower frequency. The frequency numbers will start to change rapidly. Release the bar when the display reaches the desired frequency. To change the frequency in small increments, press and release the TUNE/SEEK bar quickly.

) to tune to a

SEEK — The SEEK function searches the band for a station with a strong signal. To activate it, press the TUNE/SEEK bar until you hear a beep, then release it. Depending on which part of the bar you pressed, the system scans upward or down- ward from the current frequency. It stops when it finds a station with a strong signal.

Preset — You can store the fre- quencies of your favorite radio stations in the six preset buttons. Each button will store one frequency on the AM band, and two on the FM band.

Audio System

To store a frequency:

1. Select the desired band, AM or FM. FM1 and FM2 let you store two frequencies with each Preset button.

2. Use the TUNE or SEEK bar to

tune the radio to the desired station.

3. Pick the Preset button you want for that station. Press the button and hold it until you hear a beep.

4. Repeat steps 1 to 3 to store a total

of six stations on AM and twelve on FM.

Once a station's frequency is stored, simply press and release the proper Preset button to tune to it. The preset frequencies will be lost if your vehicle's battery goes dead, is disconnected or the radio fuse is removed.

Comfort and Convenience Features

Audio System

Adjusting the Sound Balance/Fader — These two controls adjust the strength of the sound coming from each speaker. The Balance control adjusts the side- to-side strength, while the Fader control adjusts the front-to-back strength.

Adjust the Fader to your liking by turning the outside ring. Adjust the Balance by pulling out the SW-VOL/ BAL knob and turning it.

Treble/Bass — Use these controls to adjust the tone to your liking. Adjust the Bass by turning the knob. Adjust the Treble by pulling out the knob and turning it.

Comfort and Convenience Features

BALANCE CONTROL

FADER CONTROL

TONE CONTROL

Radio Frequencies and Reception For information, See page 110.

Operating the Cassette Player Turn the audio system ON. Make sure the tape opening on the cassette is facing to the right, then insert the cassette most of the way into the slot. The system will pull it in the rest of the way, and begin to play.

The tape direction indicator will light to show you which side of the cassette is playing. The indicates the side you inserted facing upward is now playing. If you want to play the other side, press the Fast Forward/Rewind buttons at the same time.

Audio System

EJECT BUTTON

FAST FORWARD BUTTON

REWIND BUTTON

TAPE DIRECTION INDICATOR

CASSETTE SLOT

When the system reaches the end of the tape, it will automatically reverse direction and play the other side. If you want to remove the cassette from the drive, press the EJECT button.

Comfort and Convenience Features

FAST FORWARD BUTTON

REWIND BUTTON

Audio System

Tape Search Functions FF/REW — Fast Forward and Rewind move the tape rapidly. Press the REW button to rewind the tape, the FF button to fast forward. To take the system out of rewind, press the FF button briefly. To take the system out of fast forward, press REW briefly. If the system reaches the end of the tape while in fast forward or rewind, it automatically stops that function, reverses direction, and begins to play.

Caring for Cassettes Damaged cassettes can jam inside the drive or cause other problems. See page 121 for information on cassette care and protection.

Comfort and Convenience Features

Audio System

(U.S.: VALUE PACKAGE LX, LX V-6
Canada: EX)

(U.S.: EX, EX V-6
Canada: EX-R, EX-R V-6)

AM/FM/Cassette Stereo Audio System For Value Package LX, LX V-6, EX and EX V-6 in the U.S. and EX, EX-R and EX-R V-6 in Canada Your Honda's audio system provides clear reception on both AM and FM bands, while the preset buttons allow you to easily select your favorite stations. The cassette system features Dolby B* noise reduction, automatic sensing of chromium-dioxide (CrO tape, and autoreverse for continuous play.

* Dolby noise reduction manufactured under license from Dolby Laboratories Licensing Corpo- ration. "DOLBY" and the double-D symbol are trademarks of Dolby Laboratories

Licensing Corporation.

CONTINUED

Comfort and Convenience Features

You can use any of three methods to find radio stations on the selected band: TUNE, SEEK, or the Preset buttons.

TUNE — Use the TUNE/SEEK switch to tune the radio to a desired frequency. Push the switch up to tune to a higher frequency, and push the switch down to tune to a lower frequency. The frequency numbers will start to change rapidly. Release the switch when the display reaches the desired frequency. To change the frequency in small increments, push and release the TUNE/SEEK switch quickly.

SEEK — The SEEK function searches the band for a station with a strong signal. To activate it, push the TUNE/SEEK switch until you hear a beep, then release it. Depending on which way you pushed the switch, the system scans upward or downward from the current frequency. It stops when it finds a station with a strong signal.

Preset — You can store the fre- quencies of your favorite radio stations in the six preset buttons. Each button will store one frequency on the AM band, and two on the FM band.

Audio System

U.S. EX, EX V-6 and Canadian EX-R, EX-R V-6
The Anti-theft feature will disable the system if it is disconnected from the car's battery. To get the system working again, you must enter a code number (see page 122 ).

Operating the Radio The ignition switch must be in AC- CESSORY (I) or ON (II) to operate the audio system. Turn the system on and adjust the volume by turning the ON/OFF/VOL knob.

The band and frequency that the radio was last tuned to is displayed. To change bands, press the AM/FM button. On the FM band, ST will be displayed if the station is broadcast- ing in stereo. Stereo reproduction on AM is not available.

Comfort and Convenience Features

To store a frequency:

1. Select the desired band, AM or FM. FM1 and FM2 let you store two frequencies with each Preset button.

2. Use the TUNE or SEEK function

to tune the radio to a desired station.

3. Pick the Preset button you want for that station. Press the button and hold it until you hear a beep.

4. Repeat steps 1 to 3 to store a total of six stations on AM and twelve on FM.

Once a station's frequency is stored, simply press and release the proper preset button to tune to it. The preset frequencies will be lost if your vehicle's battery goes dead, is disconnected or the radio fuse is removed.

Audio System

(U.S.: VALUE PACKAGE LX, LX V-6
Canada: EX)

ON/OFF/VOL KNOB

CASSETTE SLOT

TUNE/SEEK FF/REW/TMS SWITCH

AM/FM BUTTONS

PRESET BUTTONS

(U.S.: EX, EX V-6
Canada: EX-R, EX-R V-6)

ON/OFF/VOL KNOB

CASSETTE SLOT

TUNE/SEEK FF/REW/TMS SWITCH

AM/FM BUTTONS

PRESET BUTTONS

CONTINUED

Comfort and Convenience Features

Audio System

For EX and EX V-6 models in the U.S. and EX-R, EX-R V-6 models in Canada AUTO SELECT — If you are traveling far from home and can no longer receive the stations you preset, you can use the Auto Select feature to find stations in the local area. To activate Auto Select, press the A. SELECT button. A. SELECT will appear in the display, and the system will go into scan mode for several seconds. It automatically scans both bands, looking for stations with strong signals. It stores the frequen- cies of six AM stations and twelve FM stations in the preset buttons. You can then use the preset buttons to select those stations. If you are in a remote area, Auto Select may not find six strong AM stations or twelve strong FM stations. If this happens, you will see a "0" displayed when you press any preset button that does not have a station stored.

Comfort and Convenience Features

(U.S.: EX, EX V-6, Canada: EX-R, EX-R V-6)

AUTO SELECT LIGHT

AUTO SELECT BUTTON

With Auto Select on, you cannot manually store any frequencies in the preset buttons. If you do not like the stations found by Auto Select, you can use the TUNE and SEEK functions to find other stations.

Auto Select does not erase the frequencies that you preset pre- viously. When you return home, turn off Auto Select by pressing the A. SELECT button. The preset buttons will then select the fre- quencies you originally set.

Audio System

Adjusting the Sound Balance/Fader — These two controls adjust the strength of the sound coming from each speaker. The Balance control adjusts the side- to-side strength, while the Fader control adjusts the front-to-back strength.

To use these controls, push on the knob to get them to pop out. Adjust the Fader to your liking by turning the outside ring. Adjust the Balance by turning the knob. Push the controls back in when you are done.

Treble/Bass — Use these controls to adjust the tone to your liking. Push on the controls to get them to pop out. Adjust the Bass by turning the outer ring. Adjust the Treble by turning the knob. Push the controls back in when you are finished so you cannot change the settings by accidentally bumping them.

FADER CONTROL

BALANCE CONTROL

BASS CONTROL

TREBLE CONTROL

Audio System Lighting You can use the Balance control knob to turn off the illumination of the audio system. Push the Balance/ Fader controls so they pop out, then pull the Balance control knob out slightly farther.

Check the Balance control knob if the audio system does not illuminate with the instrument panel lights.

Radio Frequencies and Reception For information, See page 110.

Comfort and Convenience Features

Audio System

Operating the Cassette Player Turn the audio system ON. Make sure the tape opening on the cassette is facing to the right, then insert the cassette most of the way into the slot. The system will pull it in the rest of the way, and begin to play.

The tape direction indicator will light to show you which side of the cassette is playing. The indicates the side you inserted facing upward is now playing. If you want to play the other side, press the PROG button.

Dolby B noise reduction turns on when you insert a cassette. If the tape was not recorded with Dolby B noise reduction, turn it off by pressing the

button.

Comfort and Convenience Features

When the system reaches the end of the tape, it will automatically reverse direction and play the other side. If you want to remove the cassette from the drive, press the EJECT button.

The system will automatically eject the cassette whenever you turn off the system or the ignition switch.

Tape Search Functions With a cassette playing, you can use the FF, REW, TMS, or REPEAT function to find a desired program.

FF/REW — Fast Forward and Rewind move the tape rapidly. To rewind the tape, push the FF/REW/ TMS switch down, then release it. You will see REW in the display. To fast forward the tape, push the switch up, then release it. You will see FF displayed. Press the PLAY button to take the system out of rewind or fast forward. If the system

reaches the end of the tape while in fast forward or rewind, it auto- matically stops that function, reverses direction, and begins to play.

TMS — The Tape Music Search Function allows you to find the beginning of a song or passage. You activate TMS with the FF/REW/ TMS switch. To find the beginning of the song or passage currently playing, push the switch down and hold it until you hear a beep. You will see REW flashing in the display as the tape rewinds. To find the beginning of the next song, push the switch up and hold it until you hear a beep. You will see FF flashing in the display as the tape fast forwards. When the system finds the begin- ning of a song or passage, it goes back to PLAY mode.

REPEAT — The Repeat function continuously replays the current song or passage. Press the REPEAT button to activate it; you will see RPT displayed as a reminder. When the system reaches the end of the song or passage currently playing, it will automatically go into rewind. When it senses the beginning of the same song or passage, the system returns to PLAY mode. It will continue to repeat this same program until you deactivate REPEAT by pressing the button again.

Audio System

(U.S.: VALUE PACKAGE LX, LX V-6
Canada: EX)

CASSETTE SLOT

TAPE DIRECTION INDICATOR

FF/REW/TMS SWITCH

EJECT BUTTON

PROG BUTTON

PLAY BUTTON

DOLBY BUTTON

REPEAT BUTTON

(U.S.: EX, EX V-6
Canada: EX-R, EX-RV-6)

CASSETTE SLOT

TAPE DIRECTION INDICATOR

FF/REW/TMS SWITCH

EJECT BUTTON

PROG BUTTON

PLAY BUTTON

DOLBY BUTTON

REPEAT BUTTON

CONTINUED

Comfort and Convenience Features

Audio System

The TMS and REPEAT functions use silent periods on the tape to find the end of a song or passage. These features may not work to your satisfaction if there is almost no gap between selections, a high noise level between selections, or a silent period in the middle of a selection.

Caring for Cassettes Damaged cassettes can jam inside the drive or cause other problems. See page 121 for information on cassette care and protection.

(U.S.: VALUE PACKAGE LX, LX V-6
Canada: EX)

CASSETTE SLOT

TAPE DIRECTION INDICATOR

FF/REW/TMS SWITCH

EJECT BUTTON

PROG BUTTON

PLAY BUTTON

DOLBY BUTTON

REPEAT BUTTON

(U.S.: EX, EX V-6
Canada: EX-R, EX-R V-6)

CASSETTE SLOT

TAPE DIRECTION INDICATOR

FF/REW/TMS SWITCH

EJECT BUTTON

PROG BUTTON

PLAY BUTTON

DOLBY BUTTON

REPEAT BUTTON

Comfort and Convenience Features

Operating the Optional CD Changer Optional for U.S. Value Package LX, LX V-6, EX and EX V-6 models and Canadian EX, EX-R and EX-R V-6
models A Compact Disc changer is available from your dealer. It holds up to six discs, providing several hours of continuous entertainment. You operate the CD changer with the same controls used for the radio and cassette player.

Your dealer also has an accessory in- dash single CD player available that is operated by the radio controls. To operate this unit, use the instructions (except for those relating to multiple discs) in this section.

Using the instructions that came with the changer, load the desired CDs in the magazine, and load the magazine in the changer.

Audio System

(U.S.: VALUE PACKAGE LX, LX V-6
Canada: EX)

ON/OFF/VOL KNOB

RPT INDICATOR

TUNE/SEEK SWITCH

CD BUTTON

REPEAT BUTTON

ON/OFF/VOL KNOB

A. SELECT INDICATOR

RPT INDICATOR

(U.S.: EX, EX V-6
Canada: EX-R, EX-R V-6)

TUNE/SEEK SWITCH

CD BUTTON

A. SELECT/ REPEAT BUTTON

CONTINUED

Comfort and Convenience Features

Audio System

To operate the CD changer, the ignition must be in ACCESSORY (I) or ON (II) and the audio system must be on. If you are listening to a cassette, eject it.

Press the CD button until "CD" appears in the display. The system will start to play the first track of the first disc in the magazine. When that disc ends, the next disc in the magazine is loaded and played. After the last disc finishes, the system returns to disc 1.

To select a different disc, press the appropriate preset button (1 — 6). If you select an empty slot in the magazine, the changer will, after finding that slot empty, try to load the CD in the next slot. This continues until it finds a CD to load and play.

Comfort and Convenience Features

You can use the TUNE/SEEK switch to select tracks within a disc. If you push and release the TUNE/ SEEK switch, the system will move to the beginning of a track. Push the switch up to move to the beginning of the next track, and push the switch down to move to the begin- ning of the current track.

If you push and hold the TUNE/ SEEK switch, you will hear a beep and the system will continue to move across tracks. Release the switch when you think it has reached the desired place on the disc.

REPEAT — When you activate the Repeat feature by pressing the REPEAT button, the system continu- ously replays the current track. You will see RPT in the display as a reminder. Press the REPEAT button again to turn it off.

(U.S.: EX, EX V-6, Canada: EX-R, EX-R V-6) RANDOM PLAY — This feature, when activated, plays the tracks on a CD in random order, rather than in the order they are recorded on the CD. To activate Random Play, press and hold the A. SELECT/REPEAT button until you see A. SELECT in the display. The system will then select and play tracks randomly on the current disc. When all tracks on that disc have been played, the next disc is loaded and played randomly. This continues until you deactivate Random Play by pressing A. SELECT/REPEAT again.

If the system is in Repeat mode, you must turn it off by pressing A. SELECT/REPEAT before you can select Random Play. Then press the button again until you see A. SELECT displayed.

To take the system out of CD mode, press the AM or FM button, or insert a cassette in the player. When you return to CD mode, play will contin- ue at the same disc and track.

If you turn the system off while a CD is playing, either with the ON-OFF/ VOL knob or the ignition switch, play will continue at the same disc and track when you turn it back on.

Protecting Compact Discs For information on how to handle and protect compact discs, see page 115.

Audio System

(U.S.: VALUE PACKAGE LX, LX V-6
Canada: EX)

ON/OFF/VOL KNOB

RPT INDICATOR

TUNE/SEEK SWITCH

CD BUTTON

REPEAT BUTTON

ON/OFF/VOL KNOB

A. SELECT INDICATOR

RPT INDICATOR

(U.S.: EX, EX V-6
Canada: EX-R, EX-R V-6)

TUNE/SEEK SWITCH

CD BUTTON

A. SELECT/ REPEAT BUTTON

Comfort and Convenience Features

Audio System

CD Changer Error Indications If you see an error indication in the display while operating the CD changer, find the cause in the chart to the right. If you cannot clear the error indication, take the car to your Honda dealer.

Comfort and Convenience Features

Audio System

AM/FM 1-2 BUTTON

TUNE BAR

AM/FM/CD Audio System For Special Edition model Your Honda's audio system provides clear reception on both AM and FM bands, while the preset buttons allow you to easily select your favorite stations.

The Anti-theft feature will disable the system if it is disconnected from the car's battery. To get the system working again, you must enter a code number (see page 122 ).

PRESET BUTTONS