2015 GMC Savana Owners Manual

conditioner.

Malfunction Indicator Lamp A computer system called OBD II (On-Board Diagnostics-Second Generation) monitors the operation of the vehicle to ensure emissions

GMC Savana Owner Manual 2015 - crc - 6/3/14

(GMNA-Localizing-U.S./Canada-7707482)

Black plate (17,1)

are at acceptable levels, helping to maintain a clean environment. The malfunction indicator lamp comes on when the vehicle is placed in ON/RUN, as a check to show it is working. If it does not, have the vehicle serviced by your dealer. See Ignition Positions on page 9-14.

If the malfunction indicator lamp comes on while the engine is running, this indicates that the OBD II system has detected a problem and diagnosis and service might be required. Malfunctions often are indicated by the system before any problem is apparent. Being aware of the light can prevent more serious damage to the vehicle. This system also

Instruments and Controls

5-17

assists the service technician in correctly diagnosing any malfunction.

{ Caution

If the vehicle is continually driven with this light on, the emission controls might not work as well, the vehicle fuel economy might not be as good, and the engine might not run as smoothly. This could lead to costly repairs that might not be covered by the vehicle warranty.

{ Caution

Modifications made to the engine, transmission, exhaust, intake, or fuel system of the vehicle or the replacement of the original tires with other than those of the same Tire Performance Criteria

(Continued)

Caution (Continued)

(TPC) can affect the vehicle's emission controls and can cause this light to come on. Modifications to these systems could lead to costly repairs not covered by the vehicle warranty. This could also result in a failure to pass a required Emission Inspection/Maintenance test. See Accessories and Modifications on page 10-2.

This light may come on during a malfunction in one of two ways: Light Flashing: A misfire condition has been detected. A misfire increases vehicle emissions and could damage the emission control system on the vehicle. Diagnosis and service might be required. To prevent more serious damage to the vehicle: . Reduce vehicle speed.

GMC Savana Owner Manual 2015 - crc - 6/3/14

(GMNA-Localizing-U.S./Canada-7707482)

Black plate (18,1)

5-18

Instruments and Controls

. Avoid hard accelerations. . Avoid steep uphill grades.

If towing a trailer, reduce the amount of cargo being hauled as soon as it is possible.

If the light continues to flash, find a safe place to stop and park the vehicle. Turn the vehicle off, wait at least 10 seconds, and restart the engine. If the light is still flashing, follow the previous steps and see your dealer for service as soon as possible. Light On Steady: An emission control system malfunction has been detected on the vehicle. Diagnosis and service might be required. The following may correct an emission control system malfunction: . Check that the fuel cap is fully

installed. See Filling the Tank on page 9-41. The diagnostic system may be able to determine if the fuel cap has

been left off or improperly installed. A loose or missing fuel cap could allow fuel to evaporate into the atmosphere. A few driving trips with the cap properly installed may turn the light off.

. Check that good quality fuel is used. Poor fuel quality causes the engine not to run as efficiently as designed and may cause stalling after start-up, stalling when the vehicle is changed into gear, misfiring, hesitation on acceleration, or stumbling on acceleration. These conditions might go away once the engine is warmed up. If this occurs, change the fuel brand used. It may require at least one full tank of the proper fuel to turn the light off.

See Fuel on page 9-39. If the light remains on, your dealer can check the vehicle. The dealer has the proper test equipment and

diagnostic tools to fix any mechanical or electrical problems that might have developed. Emissions Inspection and Maintenance Programs Depending on where you live, your vehicle may be required to participate in an emission control system inspection and maintenance program. For the inspection, the emission system test equipment will likely connect to the vehicle's Data Link Connector (DLC).

The DLC is under the instrument panel to the left of the steering wheel. See your dealer if assistance is needed.

GMC Savana Owner Manual 2015 - crc - 6/3/14

(GMNA-Localizing-U.S./Canada-7707482)

Black plate (19,1)

Instruments and Controls

5-19

inspection for lack of OBD II system readiness, your dealer can prepare the vehicle for inspection.

Brake System Warning Light The vehicle brake system consists of two hydraulic circuits. If one circuit is not working, the remaining circuit can still work to stop the vehicle. For normal braking performance, both circuits need to be working. If the warning light comes on, there could be a brake problem. Have the brake system inspected right away.

Metric

English

This light should come on briefly when ignition key is turned to ON/ RUN. If it does not come on, have it fixed so it will be ready to warn if there is a problem. When the ignition is on, the brake system warning light also comes on when the parking brake is set. See Parking Brake on page 9-29 for more information. The light stays on if the parking brake does not fully release. If it stays on after the parking brake is fully released, it means the vehicle has a brake problem. If the light comes on while driving, pull off the road and stop carefully. The pedal might be harder to push, or the pedal might go closer to the floor. It could take longer to stop. If the light is still on, have the vehicle towed for service. See Towing the Vehicle on page 10-77.

The vehicle may not pass inspection if:

The malfunction indicator lamp is on with the engine running, or if the light does not come on when the ignition is turned to ON/RUN while the engine is off. See your dealer for assistance in verifying proper operation of the malfunction indicator lamp. The OBD II (On-Board Diagnostics) system determines that critical emission control systems have not been completely diagnosed. The vehicle would be considered not ready for inspection. This can happen if the 12-volt battery has recently been replaced or run down.

The diagnostic system is designed to evaluate critical emission control systems during normal driving. This can take several days of routine driving. If this has been done and the vehicle still does not pass the

GMC Savana Owner Manual 2015 - crc - 6/3/14

(GMNA-Localizing-U.S./Canada-7707482)

Black plate (20,1)

5-20

Instruments and Controls

{ Warning

The brake system might not be working properly if the brake system warning light is on. Driving with the brake system warning light on can lead to a crash. If the light is still on after the vehicle has been pulled off the road and carefully stopped, have the vehicle towed for service.

Antilock Brake System (ABS) Warning Light

Tow/Haul Mode Light

For vehicles with the Tow/Haul Mode feature, this light comes on when the Tow/Haul Mode has been activated. See Tow/Haul Mode on page 9-27.

StabiliTrak® OFF Light

If it does not, have the vehicle serviced by your dealer. If the system is working normally the indicator light then goes off. If the ABS light stays on, turn the ignition off. If the light comes on while driving, stop as soon as it is safely possible and turn the ignition off. Then start the engine again to reset the system. If the ABS light stays on, or comes on again while driving, the vehicle needs service. If the regular brake system warning light is not on, the vehicle still has brakes, but not antilock brakes. If the regular brake system warning light is also on, the vehicle does not have antilock brakes and there is a problem with the regular brakes. See Brake System Warning Light on page 5-19.

For vehicles with the Antilock Brake System (ABS), this light comes on briefly when the engine is started.

This light comes on briefly while starting the engine. If it does not, have the vehicle serviced by your dealer.

GMC Savana Owner Manual 2015 - crc - 6/3/14

(GMNA-Localizing-U.S./Canada-7707482)

Black plate (21,1)

Instruments and Controls

5-21

This light comes on when the StabiliTrak system is turned off. If StabiliTrak is off, the Traction Control System (TCS) is also off. If the StabiliTrak and TCS are off, the system does not assist in controlling the vehicle. Turn on the TCS and the StabiliTrak systems and the warning light turns off. See Traction Control/Electronic Stability Control on page 9-29.

Traction Control System (TCS)/StabiliTrak® Light

This light comes on briefly when the engine is started.

If the light does not come on, have the vehicle serviced by your dealer. If the system is working normally, the indicator light turns off. If the light is on and not flashing, the TCS and potentially the StabiliTrak system have been disabled. A DIC message may display. Check the DIC messages to determine which feature(s) is no longer functioning and whether the vehicle requires service. If the indicator/warning light is on and flashing, the TCS and/or the StabiliTrak system is actively working. See Traction Control/Electronic Stability Control on page 9-29.

Tire Pressure Light

For vehicles with the Tire Pressure Monitor System (TPMS), this light comes on briefly when the engine is started. It provides information about tire pressures and the TPMS.

When the Light Is On Steady This indicates that one or more of the tires are significantly underinflated. A Driver Information Center (DIC) tire pressure message may also display. See Tire Messages on page 5-35. Stop as soon as possible, and inflate the tires to the pressure value shown on the Tire and Loading Information label. See Tire Pressure on page 10-49.

When the Light Flashes First and Then Is On Steady If the light flashes for about a minute and then stays on, there may be a problem with the TPMS. If the problem is not corrected, the light will come on at every ignition cycle. See Tire Pressure Monitor Operation on page 10-51.

GMC Savana Owner Manual 2015 - crc - 6/3/14

(GMNA-Localizing-U.S./Canada-7707482)

Black plate (22,1)

5-22

Instruments and Controls

Engine Oil Pressure Light

low can also damage the

{ Caution Lack of proper engine oil maintenance can damage the engine. Driving with the engine oil engine. The repairs would not be covered by the vehicle warranty. Check the oil level as soon as possible. Add oil if required, but if the oil level is within the operating range and the oil pressure is still low, have the vehicle serviced. Always follow the maintenance schedule for changing engine oil.

This light should come on briefly as the engine is started. If it does not come on, have the vehicle serviced by your dealer. If the light comes on and stays on, it means that oil is not flowing through the engine properly. The vehicle could be low on oil and might have some other system problem. See your dealer.

Low Fuel Warning Light

English Shown, Metric Similar

This light comes on for a few seconds when the ignition is turned on as a check to indicate it is working. If it does not come on, have it fixed. The low fuel warning light comes on and a chime sounds when the vehicle is low on fuel. The light turns off when fuel is added to the fuel tank. See Driver Information Center (DIC) on page 5-23.

GMC Savana Owner Manual 2015 - crc - 6/3/14

(GMNA-Localizing-U.S./Canada-7707482)

Black plate (23,1)

Security Light

High-Beam On Light

Information Displays

Instruments and Controls

5-23

The security light should come on briefly as the engine is started. If it does not come on, have the vehicle serviced by your dealer. If the system is working normally, the indicator light turns off. If the light stays on and the engine does not start, there could be a problem with the theft-deterrent system. See Immobilizer Operation on page 2-11.

This light comes on when the high-beam headlamps are in use. See Headlamp High/Low-Beam Changer on page 6-2.

Cruise Control Light

This light comes on when the cruise control is set. This light goes out when the cruise control is canceled. See Cruise Control on page 9-32.

Driver Information Center (DIC) This vehicle has a DIC. All messages will appear in the DIC display at the bottom of the instrument cluster. The DIC comes on when the ignition is on. After a short delay, the DIC will display the information that was last displayed before the engine was turned off. The DIC displays trip, fuel, and vehicle system information, and warning messages if a system problem is detected. If the vehicle has these features, the DIC also displays the compass direction and the outside air temperature when viewing the trip and fuel information. The compass direction appears on the top right corner of the DIC display. The outside air temperature

GMC Savana Owner Manual 2015 - crc - 6/3/14

(GMNA-Localizing-U.S./Canada-7707482)

Black plate (24,1)

5-24

Instruments and Controls

automatically appears in the bottom right corner of the DIC display. If there is a problem with the system that controls the temperature display, the numbers will be replaced with dashes. If this occurs, have the vehicle serviced by your dealer. If the vehicle has a diesel engine, see the Duramax diesel supplement. DIC Operation and Displays The DIC has different displays which can be accessed by pressing the DIC buttons on the instrument panel, next to the instrument cluster.

DIC Buttons

The buttons are the trip/fuel, vehicle information, customization, and set/ reset buttons. The button functions are detailed in the following pages. 3 (Trip/Fuel): Press this button to display the odometer, trip odometers, fuel range, average economy, fuel used, timer, average speed, and digital tachometer.

T (Vehicle Information): Press this button to display the oil life, rear park assist, units, tire pressure readings for vehicles with the Tire Pressure Monitor System (TPMS), engine hours, Tire Pressure Monitor System (TPMS) programming for vehicles with the TPMS and without a Remote Keyless Entry (RKE) transmitter, and compass zone and compass calibration on vehicles with this feature. U (Customization): Press this button to customize the feature settings on the vehicle. See Vehicle Personalization on page 5-37 for more information. V (Set/Reset): Press this button to set or reset certain functions and to turn off or acknowledge messages on the DIC.

GMC Savana Owner Manual 2015 - crc - 6/3/14

(GMNA-Localizing-U.S./Canada-7707482)

Black plate (25,1)

Instruments and Controls

5-25

Trip/Fuel Menu Items 3 (Trip/Fuel): Press this button to scroll through the following menu items:

Odometer Press 3 until XX km (mi) displays. This display shows the distance the vehicle has been driven in either kilometers (km) or miles (mi).

Trip Odometers Press 3 until A or B displays. This display shows the current distance traveled in either kilometers (km) or miles (mi) since the last reset for each trip odometer. Both trip odometers can be used at the same time. Each trip odometer can be reset to zero separately by pressing V while the desired trip odometer is displayed.

The trip odometer has a feature called the retro-active reset. This can be used to set the trip odometer to the number of kilometers (miles) driven since the ignition was last turned on. This can be used if the trip odometer is not reset at the beginning of the trip. To use the retro-active reset feature, press and hold V for at least four seconds. The trip odometer will display the number of kilometers (km) or miles (mi) driven since the ignition was last turned on and the vehicle was moving. Once the vehicle begins moving, the trip odometer will accumulate mileage. For example, if the vehicle was driven 8 km (5 miles) before it is started again, and then the retro-active reset feature is activated, the display will show 8 km (5 miles). As the vehicle begins moving, the display will then increase to 8.1 km (5.1 miles), 8.2 km (5.2 miles), etc.

If the retro-active reset feature is activated after the vehicle is started, but before it begins moving, the display will show the number of kilometers (km) or miles (mi) that were driven during the last ignition cycle.

Fuel Range Press 3 until FUEL RANGE displays. This display shows the approximate number of remaining kilometers (km) or miles (mi) the vehicle can be driven without refueling. The display will show LOW if the fuel level is low. The fuel range estimate is based on an average of the fuel economy over recent driving history and the amount of fuel remaining in the fuel tank. This estimate will change if driving conditions change. For example, if driving in traffic and making frequent stops, this display may read one number, but if the vehicle is driven on a freeway, the number may change even though the same amount of fuel is in the

GMC Savana Owner Manual 2015 - crc - 6/3/14

(GMNA-Localizing-U.S./Canada-7707482)

Black plate (26,1)

5-26

Instruments and Controls

fuel tank. This is because different driving conditions produce different fuel economies. Generally, freeway driving produces better fuel economy than city driving. If the vehicle is low on fuel, the FUEL LEVEL LOW message will be displayed. See Fuel System Messages on page 5-31.

Average Economy Press 3 until AVG ECONOMY displays. This display shows the approximate average liters per 100 kilometers (L/100 km) or miles per gallon (mpg). This number is calculated based on the number of L/100 km (mpg) recorded since the last time this menu item was reset. To reset AVG ECONOMY, press and hold V. The display will return to zero.

Fuel Used Press 3 until FUEL USED displays. This display shows the number of liters (L) or gallons (gal)

of fuel used since the last reset of this menu item. To reset the fuel used information, press and hold V while FUEL USED is displayed.

Timer Press 3 until TIMER displays. This display can be used as a timer.

To start the timer, press V while TIMER is displayed. The display will show the amount of time that has passed since the timer was last reset, not including time the ignition is off. Time will continue to be counted as long as the ignition is on, even if another display is being shown on the DIC. The timer will record up to 99 hours, 59 minutes and 59 seconds (99:59:59) after which the display will return to zero.

To stop the timer, press V briefly while TIMER is displayed. To reset the timer to zero, press and hold V while TIMER is displayed.

Average Speed Press 3 until AVERAGE SPEED displays. This display shows the average speed of the vehicle in kilometers per hour (km/h) or miles per hour (mph). This average is calculated based on the various vehicle speeds recorded since the last reset of this value. To reset the value, press and hold V. The display will return to zero.

Digital Tachometer Press 3 until Tachometer ##00 RPM displays. This display shows the engine speed in revolutions per minute (RPM).

Blank Display This display shows no information.

GMC Savana Owner Manual 2015 - crc - 6/3/14

(GMNA-Localizing-U.S./Canada-7707482)

Black plate (27,1)

Instruments and Controls

5-27

Vehicle Information Menu Items T (Vehicle Information): Press this button to scroll through the following menu items:

Oil Life

Press T until OIL LIFE REMAINING displays. This display shows an estimate of the oil's remaining useful life. If you see 99% OIL LIFE REMAINING on the display, that means 99% of the current oil life remains. The engine oil life system will alert you to change the oil on a schedule consistent with your driving conditions. When the remaining oil life is low, the CHANGE ENGINE OIL SOON message will appear on the display. See Engine Oil Messages on page 5-30. You should change the oil as soon as possible. See Engine Oil on page 10-6. In addition to the engine oil life system monitoring the oil life, additional maintenance is

recommended in the Maintenance Schedule in this manual. See Maintenance Schedule on page 11-3. Remember, you must reset the OIL LIFE yourself after each oil change. It will not reset itself. Also, be careful not to reset the OIL LIFE accidentally at any time other than when the oil has just been changed. It cannot be reset accurately until the next oil change. To reset the engine oil life system, see Engine Oil Life System on page 10-8.

Park Assist If the vehicle has the Rear Parking Assist (RPA) system, press T until PARK ASSIST displays. This display allows the system to be turned on or off. Once in this display, press to select between ON or OFF. The RPA system automatically turns back on after each vehicle start. When the RPA system is turned off and the vehicle is shifted out of P (Park), the DIC will display the PARK ASSIST OFF

message as a reminder that the system has been turned off. See Object Detection System Messages on page 5-32 and Parking Assist on page 9-35.

Units

Press T until UNITS displays. This display allows you to select between metric or English units of measurement. Once in this display, press V to select between METRIC or ENGLISH units.

Tire Pressure If the vehicle has the Tire Pressure Monitor System (TPMS), the pressure for each tire can be viewed in the DIC. The tire pressure will be shown in either kilopascals (kPa) or pounds per square inch (psi). Press T until the DIC displays FRONT TIRES PSI (kPa) LEFT ## RIGHT ##. Press T again until the DIC displays REAR TIRES PSI (kPa) LEFT ## RIGHT ##.

GMC Savana Owner Manual 2015 - crc - 6/3/14

(GMNA-Localizing-U.S./Canada-7707482)

Black plate (28,1)

5-28

Instruments and Controls

If a low tire pressure condition is detected by the system while driving, a message advising you to check the pressure in a specific tire will appear in the display. See Tire Pressure on page 10-49 and Tire Messages on page 5-35. If the tire pressure display shows dashes instead of a value, there may be a problem with the vehicle. If this consistently occurs, see your dealer for service.

Engine Hours

Press T until ENGINE HOURS displays. This display shows the total number of hours the engine has run.

Relearn Tire Positions The vehicle may have this display. To access this display, the vehicle must be in P (Park). If the vehicle has the Tire Pressure Monitor System (TPMS), after rotating the tires or after replacing a tire or

sensor, the system must re-learn the tire positions. To re-learn the tire positions, see Tire Pressure Monitor System on page 10-50. See Tire Inspection on page 10-55, Tire Rotation on page 10-55 and Tire Messages on page 5-35.

Change Compass Zone The vehicle may have this feature. To change the compass zone through the DIC, see Compass on page 5-4.

Calibrate Compass The vehicle may have this feature. The compass can be manually calibrated. To calibrate the compass through the DIC, see Compass on page 5-4.

Blank Display This display shows no information.

Vehicle Messages Messages displayed on the DIC indicate the status of the vehicle or some action may be needed to correct a condition. Multiple messages may appear one after another. The messages that do not require immediate action can be acknowledged and cleared by pressing V (Set/Reset).

The messages that require immediate action cannot be cleared until that action is performed. All messages should be taken seriously and clearing the message does not correct the problem. The following are the possible messages and some information about them. If the vehicle has a diesel engine, see the Duramax diesel supplement.

GMC Savana Owner Manual 2015 - crc - 6/3/14

(GMNA-Localizing-U.S./Canada-7707482)

Black plate (29,1)

Instruments and Controls

5-29

Battery Voltage and Charging Messages

SERVICE BATTERY CHARGING SYSTEM On some vehicles, this message displays if there is a problem with the battery charging system. Under certain conditions, the charging system light may also turn on in the instrument cluster. See Charging System Light on page 5-16. Driving with this problem could drain the battery. Turn off all unnecessary accessories. Have the electrical system checked as soon as possible. See your dealer.

Brake System Messages

SERVICE BRAKE SYSTEM This message displays along with the brake system warning light if there is a problem with the brake system. See Brake System Warning Light on page 5-19. If this message appears, stop as soon as possible

and turn off the vehicle. Restart the vehicle and check for the message on the DIC display. If the message is still displayed or appears again when you begin driving, the brake system needs service as soon as possible. See your dealer.

Compass Messages

CALIBRATING: DRIVE IN CIRCLES This message displays when calibrating the compass. Drive the vehicle in circles at less than 8 km/h (5 mph) to complete the calibration. See Compass on page 5-4 for more information. CALIBRATION COMPLETE This message displays when the compass calibration is complete. See Compass on page 5-4 for more information.

Door Ajar Messages

CARGO DOOR OPEN This message displays and a chime sounds if the cargo door is open while the ignition is in ON/RUN. Turn off the vehicle and check the cargo door. Restart the vehicle and check for the message on the DIC display. DRIVER DOOR OPEN This message displays and a chime sounds if the driver door is not fully closed and the vehicle is in a drive gear. Stop and turn off the vehicle, check the door for obstructions, and close the door again. Check to see if the message still appears on the DIC. LEFT REAR DOOR OPEN On some vehicles, this message displays and a chime sounds if the driver side rear door is not fully closed and the vehicle is in a drive gear. Stop and turn off the vehicle, check the door for obstructions, and

GMC Savana Owner Manual 2015 - crc - 6/3/14

(GMNA-Localizing-U.S./Canada-7707482)

Black plate (30,1)

5-30

Instruments and Controls

close the door again. Check to see if the message still appears on the DIC. PASSENGER DOOR OPEN This message displays and a chime sounds if the passenger door is not fully closed and the vehicle is in a drive gear. Stop and turn off the vehicle, check the door for obstructions, and close the door again. Check to see if the message still appears on the DIC. RIGHT REAR DOOR OPEN On some vehicles, this message displays and a chime sounds if the passenger side rear door is not fully closed and the vehicle is in a drive gear. Stop and turn off the vehicle, check the door for obstructions, and close the door again. Check to see if the message still appears on the DIC.

Engine Cooling System Messages

ENGINE HOT A/C (Air Conditioning) OFF This message displays when the engine coolant becomes hotter than the normal operating temperature. See Engine Coolant Temperature Gauge on page 5-13. To avoid added strain on a hot engine, the air conditioning compressor automatically turns off. When the coolant temperature returns to normal, the air conditioning compressor turns back on. You can continue to drive the vehicle. If this message continues to appear, have the system repaired by your dealer as soon as possible to avoid damage to the engine. ENGINE OVERHEATED IDLE ENGINE This message displays when the engine coolant temperature is too hot. Stop and allow the vehicle to

idle until it cools down. See Engine Coolant Temperature Gauge on page 5-13. ENGINE OVERHEATED STOP ENGINE This message displays and a chime sounds if the engine cooling system reaches unsafe temperatures for operation. Stop and turn off the vehicle as soon as it is safe to do so to avoid severe damage. This message clears when the engine has cooled to a safe operating temperature.

Engine Oil Messages

CHANGE ENGINE OIL SOON This message displays when the engine oil needs to be changed. When you change the engine oil, be sure to reset the CHANGE ENGINE OIL SOON message. See Engine Oil Life System on page 10-8 for information on how to reset the

GMC Savana Owner Manual 2015 - crc - 6/3/14

(GMNA-Localizing-U.S./Canada-7707482)

Black plate (31,1)

message. See Engine Oil on page 10-6 and Maintenance Schedule on page 11-3. ENGINE OIL LOW ADD OIL If the vehicle has an oil level sensor, this message displays if the oil level in the vehicle is low. Check the oil level and correct it as necessary. You may need to let the vehicle cool or warm up and cycle the ignition to be sure this message clears. See Engine Oil on page 10-6. OIL PRESSURE LOW STOP ENGINE This message displays if low oil pressure levels occur. Stop the vehicle as soon as safely possible and do not operate it until the cause of the low oil pressure has been corrected. Check the oil as soon as possible and have the vehicle serviced by your dealer. See Engine Oil on page 10-6.

Instruments and Controls

5-31

Engine Power Messages

Fuel System Messages

ENGINE POWER IS REDUCED This message displays and a chime sounds when the cooling system temperature gets too hot and the engine further enters the engine coolant protection mode. See Engine Overheating on page 10-18
for further information. This message also displays when the engine power is reduced. Reduced engine power can affect the vehicle's ability to accelerate. If this message is on, but there is no reduction in performance, proceed to your destination. The performance may be reduced the next time the vehicle is driven. The vehicle may be driven at a reduced speed while this message is on, but acceleration and speed may be reduced. Anytime this message stays on, the vehicle should be taken to your dealer for service as soon as possible.

FUEL LEVEL LOW This message displays and a chime sounds if the fuel level is low. Refuel as soon as possible. See Fuel Gauge on page 5-11 and Fuel on page 9-39 for more information. TIGHTEN GAS CAP This message may display along with the check engine light on the instrument cluster if the fuel cap is not tightened properly. See Malfunction Indicator Lamp on page 5-16. Reinstall the fuel cap fully. See Filling the Tank on page 9-41. The diagnostic system can determine if the fuel cap has been left off or improperly installed. A loose or missing fuel cap allows fuel to evaporate into the atmosphere. A few driving trips with the cap properly installed should turn this light and message off.

GMC Savana Owner Manual 2015 - crc - 6/3/14

(GMNA-Localizing-U.S./Canada-7707482)

Black plate (32,1)

5-32

Instruments and Controls

Key and Lock Messages

REPLACE BATTERY IN REMOTE KEY This message displays if a Remote Keyless Entry (RKE) transmitter battery is low. The battery needs to be replaced in the transmitter. See “Battery Replacement” under Remote Keyless Entry (RKE) System Operation on page 2-2.

Lamp Messages

AUTOMATIC LIGHT CONTROL OFF This message displays when the automatic headlamps are turned off. See Exterior Lamp Controls on page 6-1. AUTOMATIC LIGHT CONTROL ON This message displays when the automatic headlamps are turned on. See Exterior Lamp Controls on page 6-1.

TURN SIGNAL ON This message displays and a chime sounds if a turn signal is left on for 1.2 km (0.75 mi). Move the turn signal lever to the off position.

Object Detection System Messages

PARK ASST BLOCKED SEE OWNERS MANUAL This message displays if there is something interfering with the Rear Parking Assist (RPA) system. See Parking Assist on page 9-35. PARK ASSIST OFF After the vehicle has been started, this message displays to remind the driver that the Rear Parking Assist (RPA) system has been turned off. Press the set/reset button or the trip odometer reset stem to acknowledge this message and clear it from the DIC display. To turn the RPA system back on, see Parking Assist on page 9-35.

SERVICE PARK ASSIST This message displays if there is a problem with the Rear Parking Assist (RPA) system. Do not use this system to help you park. See Parking Assist on page 9-35. See your dealer for service.

Ride Control System Messages

SERVICE STABILITRAK If the vehicle has StabiliTrak® and this message displays, it means there may be a problem with the StabiliTrak system. If you see this message, try to reset the system. Stop; turn off the engine for at least 15 seconds; then start the engine again. If this message still comes on, it means there is a problem. You should see your dealer for service. The vehicle is safe to drive, however, you do not have the benefit of StabiliTrak, so reduce your speed and drive accordingly.

GMC Savana Owner Manual 2015 - crc - 6/3/14

(GMNA-Localizing-U.S./Canada-7707482)

Black plate (33,1)

Instruments and Controls

5-33

SERVICE TRACTION CONTROL If the vehicle has StabiliTrak, this message displays when there is a problem with the Traction Control System (TCS). When this message displays, the system will not limit wheel spin. Adjust your driving accordingly. See your dealer for service. See Traction Control/ Electronic Stability Control on page 9-29. STABILITRAK INITIALIZING If the vehicle has StabiliTrak, this message may display until first driving the vehicle and exceeding 40 km/h (25 mph) for two minutes. The StabiliTrak system is not functional until this message has turned off. See Traction Control/ Electronic Stability Control on page 9-29.

TRACTION XX STABILITRAK XX If the vehicle has StabiliTrak, this message displays when the traction control and/or StabiliTrak systems have been turned on or off. Adjust your driving accordingly. To limit wheel spin and realize the full benefits of the stability enhancement system, you should normally leave StabiliTrak on. However, you should turn StabiliTrak off if the vehicle gets stuck in sand, mud, ice, or snow and you want to rock the vehicle to attempt to free it, or if you are driving in extreme off-road conditions and require more wheel spin. See If the Vehicle Is Stuck on page 9-8. To turn the StabiliTrak system on or off, see Traction Control/Electronic Stability Control on page 9-29. STABILITRAK OFF may also display when the stability control has been automatically disabled. There are several conditions that can cause this message to appear.

. One condition is overheating,

which could occur if StabiliTrak activates continuously for an extended period of time. The message also displays if the brake system warning light is on. See Brake System Warning Light on page 5-19. The message could display if the stability system takes longer than usual to complete its diagnostic checks due to driving conditions. The message displays if an engine or vehicle related problem has been detected and the vehicle needs service. See your dealer.

The message turns off as soon as the conditions that caused the message to be displayed are no longer present.

GMC Savana Owner Manual 2015 - crc - 6/3/14

(GMNA-Localizing-U.S./Canada-7707482)

Black plate (34,1)

5-34

Instruments and Controls

Airbag System Messages

SERVICE AIRBAG This message displays if there is a problem with the airbag system. Take the vehicle to your dealer for service.

Security Messages

SERVICE THEFT DETERRENT SYSTEM This message displays when there is a problem with the theft-deterrent system. The vehicle may or may not restart so you may want to take the vehicle to your dealer before turning off the engine. See Immobilizer Operation on page 2-11 for more information.

WAIT TO START This message displays briefly when the theft-deterrent system has initially found incorrect conditions within the vehicle and is making a double check. If your vehicle does not start soon after, try to start it again. If it still does not start, have your vehicle serviced by your dealer.

Service Vehicle Messages

SERVICE A/C SYSTEM This message displays when the electronic sensors that control the air conditioning and heating systems are no longer working. Have the climate control system serviced by your dealer if you notice a drop in heating and air conditioning efficiency.

SERVICE VEHICLE SOON This message displays when a non-emissions related malfunction occurs. Have the vehicle serviced by your dealer as soon as possible. STARTING DISABLED SERVICE THROTTLE This message displays if the starting of the engine is disabled due to the electronic throttle control system. Have the vehicle serviced by your dealer immediately. This message only appears while the ignition is in ON/RUN, and will not disappear until the problem is resolved. This message cannot be acknowledged.

GMC Savana Owner Manual 2015 - crc - 6/3/14

(GMNA-Localizing-U.S./Canada-7707482)

Black plate (35,1)

Instruments and Controls

5-35

Tire Messages

CHECK TIRE PRESSURE or TIRE LOW ADD AIR TO TIRE If the vehicle has the Tire Pressure Monitor System (TPMS), this message displays when the pressure in one or more of the tires is low. The low tire pressure warning light will also come on. See Tire Pressure Light on page 5-21. This message will also indicate which tire needs to be checked. You can receive more than one tire pressure message at a time. To read the other messages that may have been sent at the same time, press the set/ reset button. If a tire pressure message appears on the DIC, stop as soon as you can. Have the tire pressures checked and set to those shown on the Tire Loading Information label. See Tires on page 10-40, Vehicle Load Limits on page 9-9, and Tire Pressure on page 10-49. The DIC also shows

the tire pressure values. See Driver Information Center (DIC) on page 5-23. SERVICE TIRE MONITOR SYSTEM If the vehicle has the Tire Pressure Monitor System (TPMS), this message displays if a part on the system is not working properly. The tire pressure light also flashes and then remains on during the same ignition cycle. See Tire Pressure Light on page 5-21. Several conditions may cause this message to appear. See Tire Pressure Monitor Operation on page 10-51 for more information. If the warning comes on and stays on, there may be a problem with the TPMS. See your dealer. TIRE LEARNING ACTIVE If the vehicle has the Tire Pressure Monitor System (TPMS), this message displays when the system

is re-learning the tire positions on the vehicle. See Driver Information Center (DIC) on page 5-23 for more information. The tire positions must be re-learned after rotating the tires or after replacing a tire or sensor. See Tire Inspection on page 10-55, Tire Rotation on page 10-55, Tire Pressure Monitor Operation on page 10-51, and Tire Pressure on page 10-49 for more information.

Transmission Messages

GRADE BRAKING DISABLED This message displays when the grade braking has been disabled with the Tow/Haul Mode button on the end of the shift lever. See Tow/ Haul Mode on page 9-27, Automatic Transmission on page 9-22, and Cruise Control on page 9-32.

GMC Savana Owner Manual 2015 - crc - 6/3/14

(GMNA-Localizing-U.S./Canada-7707482)

Black plate (36,1)

5-36

Instruments and Controls

GRADE BRAKING ENABLED This message displays when the grade braking has been enabled with the Tow/Haul Mode button on the end of the shift lever. See Tow/ Haul Mode on page 9-27, Automatic Transmission on page 9-22, and Cruise Control on page 9-32. GRADE BRAKING ON This message displays when the grade braking has been activated while driving on downhill grades. This message will only appear the first time the feature is activated in an ignition cycle. See Tow/Haul Mode on page 9-27, Automatic Transmission on page 9-22, and Cruise Control on page 9-32. SERVICE TRANSMISSION This message displays when there is a problem with the transmission. See your dealer for service.

TRANSMISSION HOT IDLE ENGINE

Vehicle Reminder Messages

ICE POSSIBLE DRIVE WITH CARE This message displays when the outside air temperature is cold enough to create icy road conditions. Adjust your driving accordingly.

{ Caution

Do not drive the vehicle while the transmission fluid is overheating, or the transmission can be damaged. This could lead to costly repairs that would not be covered by the warranty.

This message displays along with a chime if the transmission fluid in the vehicle gets hot. Driving with the transmission fluid temperature high can cause damage to the vehicle. Stop the vehicle and let it idle to allow the transmission to cool. This message clears and the chime stops when the fluid temperature reaches a safe level.

GMC Savana Owner Manual 2015 - crc - 6/3/14

(GMNA-Localizing-U.S./Canada-7707482)

Black plate (37,1)

Instruments and Controls

5-37

Entering the Feature Settings Menu 1. Turn the ignition on and place

the vehicle in P (Park). To avoid excessive drain on the battery, it is recommended that the headlamps are turned off.

2. Press U to enter the feature

settings menu. If the menu is not available, FEATURE SETTINGS AVAILABLE IN PARK will display. Before entering the menu, make sure the vehicle is in P (Park).

Feature Settings Menu Items The following are customization features that allow you to program settings to the vehicle:

DISPLAY IN ENGLISH This feature will only display if a language other than English has been set. This feature allows you to change the language in which the DIC messages appear to English.

Press U until the PRESS V TO DISPLAY IN ENGLISH screen appears on the DIC display. Press the set/reset button once to display all DIC messages in English.

LANGUAGE This feature allows you to select the language in which the DIC messages will appear.

Vehicle Personalization This vehicle may have customization capabilities that allow you to program certain features to one preferred setting. Customization features can only be programmed to one setting on the vehicle and cannot be programmed to a preferred setting for two different drivers. All of the customization options may not be available on your vehicle. Only the options available will be displayed on the DIC. The default settings for the customization features were set when the vehicle left the factory, but may have been changed from their default state since then. The customization preferences are automatically recalled. To change customization preferences, use the following procedure.

GMC Savana Owner Manual 2015 - crc - 6/3/14

(GMNA-Localizing-U.S./Canada-7707482)

Black plate (38,1)

5-38

Instruments and Controls

Press U until the LANGUAGE screen appears on the DIC display. Press V once to access the settings for this feature. Then press U to scroll through the following settings: ENGLISH (default): All messages will appear in English. FRANCAIS: All messages will appear in French. ESPANOL: All messages will appear in Spanish. ARABIC: All messages will appear in Arabic. NO CHANGE: No change will be made to this feature. The current setting will remain.

To select a setting, press V while the desired setting is displayed on the DIC. A beep will sound once a language has been selected.

AUTO DOOR LOCK This feature allows you to select when the doors will automatically lock.

Press U until AUTO DOOR LOCK appears on the DIC display. Press V once to access the settings for this feature. Then press U to scroll through the following settings: SHIFT OUT OF PARK (default): The doors will automatically lock when the vehicle is shifted out of P (Park). AT VEHICLE SPEED: The doors will automatically lock when the vehicle speed is above 13 km/h (8 mph) for three seconds. NO CHANGE: No change will be made to this feature. The current setting will remain.

To select a setting, press V while the desired setting is displayed on the DIC.

AUTO DOOR UNLOCK This feature allows you to select whether or not to turn off the automatic door unlocking feature.

It also allows you to select which doors and when the doors will automatically unlock.

Press U until AUTO DOOR UNLOCK appears on the DIC display. Press V once to access the settings for this feature. Then press U to scroll through the following settings: OFF: None of the doors will automatically unlock. DRIVER AT KEY OUT: Only the driver door will unlock when the key is taken out of the ignition. DRIVER IN PARK: Only the driver door will unlock when the vehicle is shifted into P (Park). ALL AT KEY OUT: All of the doors will unlock when the key is taken out of the ignition. ALL IN PARK (default): All of the doors will unlock when the vehicle is shifted into P (Park).

GMC Savana Owner Manual 2015 - crc - 6/3/14

(GMNA-Localizing-U.S./Canada-7707482)

Black plate (39,1)

Instruments and Controls

5-39

NO CHANGE: No change will be made to this feature. The current setting will remain.

To select a setting, press V while the desired setting is displayed on the DIC.

REMOTE DOOR LOCK This feature allows you to select the type of feedback you will receive when locking the vehicle with the Remote Keyless Entry (RKE) transmitter. You will not receive feedback when locking the vehicle with the RKE transmitter if the doors are open. See Remote Keyless Entry (RKE) System Operation on page 2-2.

Press U until REMOTE DOOR LOCK appears on the DIC display. Press V once to access the settings for this feature. Then press U to scroll through the following settings: OFF: There will be no feedback when you press Q on the RKE transmitter.

LIGHTS ONLY: The exterior lamps will flash when you press Q on the RKE transmitter. HORN ONLY: The horn will sound on the second press of Q on the RKE transmitter. HORN & LIGHTS (default): The exterior lamps will flash when you press Q on the RKE transmitter, and the horn will sound when Q is pressed again within five seconds of the previous command. NO CHANGE: No change will be made to this feature. The current setting will remain.

To select a setting, press V while the desired setting is displayed on the DIC.

REMOTE DOOR UNLOCK This feature allows you to select the type of feedback you will receive when unlocking the vehicle with the Remote Keyless Entry (RKE) transmitter. You will not receive

feedback when unlocking the vehicle with the RKE transmitter if the doors are open. See Remote Keyless Entry (RKE) System Operation on page 2-2.

Press U until REMOTE DOOR UNLOCK appears on the DIC display. Press V once to access the settings for this feature. Then press U to scroll through the following settings: LIGHTS OFF: The exterior lamps will not flash when you press K on the RKE transmitter. LIGHTS ON (default): The exterior lamps will flash when you press K on the RKE transmitter. NO CHANGE: No change will be made to this feature. The current setting will remain.

To select a setting, press V while the desired setting is displayed on the DIC.

GMC Savana Owner Manual 2015 - crc - 6/3/14

(GMNA-Localizing-U.S./Canada-7707482)

Black plate (40,1)

5-40

Instruments and Controls

DELAY DOOR LOCK This feature allows you to select whether or not the locking of the doors will be delayed. When locking the doors with the power door lock switch and a door is open, this feature will delay locking the doors until five seconds after the last door is closed. You will hear three chimes to signal that the delayed locking feature is in use. The key must be out of the ignition for this feature to work. You can temporarily override delayed locking by pressing the power door lock switch twice or Q on the RKE transmitter twice. See Delayed Locking on page 2-7.

Press U until DELAY DOOR LOCK appears on the DIC display. Press V once to access the settings for this feature. Then press U to scroll through the following settings: OFF: There will be no delayed locking of the vehicle's doors.

ON (default): The doors will not lock until five seconds after the last door is closed. NO CHANGE: No change will be made to this feature. The current setting will remain.

To select a setting, press V while the desired setting is displayed on the DIC.

EXIT LIGHTING This feature allows you to select the amount of time you want the exterior lamps to remain on when it is dark enough outside. This happens after the key is turned from ON/RUN to LOCK/OFF.

Press U until EXIT LIGHTING appears on the DIC display. Press V once to access the settings for this feature. Then press U to scroll through the following settings: OFF: The exterior lamps will not turn on.

10 SECONDS (default): The exterior lamps will stay on for 10 seconds. 1 MINUTE: The exterior lamps will stay on for one minute. 2 MINUTES: The exterior lamps will stay on for two minutes. NO CHANGE: No change will be made to this feature. The current setting will remain.

To select a setting, press V while the desired setting is displayed on the DIC.

APPROACH LIGHTING This feature allows you to select whether or not to have the exterior lamps turn on briefly during low light periods after unlocking the vehicle using the Remote Keyless Entry (RKE) transmitter.

GMC Savana Owner Manual 2015 - crc - 6/3/14

(GMNA-Localizing-U.S./Canada-7707482)

Black plate (41,1)

Instruments and Controls

5-41

CHIME VOLUME This feature allows you to select the volume level of the chime.

Press U until CHIME VOLUME appears on the DIC display. Press V once to access the settings for this feature. Then press U to scroll through the following settings: NORMAL: The chime volume will be set to a normal level. LOUD: The chime volume will be set to a loud level. NO CHANGE: No change will be made to this feature. The current setting will remain. There is no default for chime volume. The volume will stay at the last known setting.

To select a setting, press V while the desired setting is displayed on the DIC.

FACTORY SETTINGS This feature allows you to set all of the customization features back to their factory default settings.

Press U until FACTORY SETTINGS appears on the DIC display. Press V once to access the settings for this feature. Then press U to scroll through the following settings: RESTORE ALL (default): The customization features will be set to their factory default settings. DO NOT RESTORE: The customization features will not be set to their factory default settings.

To select a setting, press V while the desired setting is displayed on the DIC.

EXIT FEATURE SETTINGS This feature allows you to exit the feature settings menu.

If it is dark enough

Press U until APPROACH LIGHTING appears on the DIC display. Press V once to access the settings for this feature. Then press U to scroll through the following settings: OFF: The exterior lamps will not turn on when you unlock the vehicle with the RKE transmitter. ON (default): outside, the exterior lamps will turn on briefly when you unlock the vehicle with the RKE transmitter. The lamps will remain on for 20 seconds or until Q on the RKE transmitter is pressed, or the vehicle is no longer off. See Remote Keyless Entry (RKE) System Operation on page 2-2. NO CHANGE: No change will be made to this feature. The current setting will remain.

To select a setting, press V while the desired setting is displayed on the DIC.

GMC Savana Owner Manual 2015 - crc - 6/3/14

(GMNA-Localizing-U.S./Canada-7707482)

Black plate (42,1)

5-42

Instruments and Controls

Press U until FEATURE SETTINGS PRESS V TO EXIT appears in the DIC display. Press V once to exit the menu.

If you do not exit, pressing U will return you to the beginning of the feature settings menu. Exiting the Feature Settings Menu The feature settings menu will be exited when any of the following occurs:

The vehicle is no longer in ON/RUN. The 3 or T DIC buttons are pressed. The end of the feature settings menu is reached and exited. . A 40 second time period has

elapsed with no selection made.

GMC Savana Owner Manual 2015 - crc - 6/3/14

(GMNA-Localizing-U.S./Canada-7707482)

Black plate (1,1)

Lighting

Exterior Lighting

Exterior Lighting

Exterior Lamp Controls

Exterior Lamp Controls . . . . . . . . 6-1
Exterior Lamps Off

Reminder . . . . . . . . . . . . . . . . . . . . 6-2

Headlamp High/Low-Beam

Changer . . . . . . . . . . . . . . . . . . . . . 6-2
Flash-to-Pass . . . . . . . . . . . . . . . . . 6-2
Daytime Running

Lamps (DRL) . . . . . . . . . . . . . . . . 6-2

Automatic Headlamp

System . . . . . . . . . . . . . . . . . . . . . . 6-3
Hazard Warning Flashers . . . . . 6-4
Turn and Lane-Change

Signals . . . . . . . . . . . . . . . . . . . . . . 6-4

Interior Lighting

Instrument Panel Illumination

Control . . . . . . . . . . . . . . . . . . . . . . 6-5
Dome Lamps . . . . . . . . . . . . . . . . . 6-5
Reading Lamps . . . . . . . . . . . . . . . 6-6

Lighting Features

Entry/Exit Lighting . . . . . . . . . . . . . 6-6
Battery Load Management . . . . 6-6
Battery Power Protection . . . . . . 6-7

The exterior lamp control is on the instrument panel to the left of the steering wheel. There are four positions: O (Off): Briefly turn the control to this position to turn the automatic headlamps and Daytime Running Lamps (DRL) off or back on. For vehicles first sold in Canada, the off position only works for vehicles that are shifted into the P (Park) position.

Lighting

6-1

AUTO (Automatic): Automatically turns the exterior lamps on and off, depending on outside lighting. ; (Parking Lamps): Turns on the parking lamps including all lamps, except the headlamps. 2 (Headlamps): Turns on the headlamps together with the parking lamps and instrument panel lights. If the headlamps are turned on while the vehicle is on, the headlamps turn off automatically 10 minutes after the ignition is turned off. If the headlamps are turned on while the vehicle is off, the headlamps will continue to stay on. To prevent the battery from being drained, turn the control to the O position. A warning chime sounds if the driver door is opened while the ignition switch is off and the headlamps are on.

GMC Savana Owner Manual 2015 - crc - 6/3/14

(GMNA-Localizing-U.S./Canada-7707482)

Black plate (2,1)

6-2

Lighting

To change the headlamps from low beam to high beam, pull the turn signal lever all the way toward you. Then release it.

Exterior Lamps Off Reminder If a door is open, a reminder chime sounds when the headlamps or parking lamps are manually turned on and the key is out of the ignition. To turn off the chime, turn the headlamp switch to O or AUTO and then back on, or close and re‐open the door. In the auto mode, the headlamps turn off once the ignition is in LOCK/OFF or may remain on until the headlamp delay ends, if enabled in the Driver Information Center (DIC). See “Exit Lighting” under Vehicle Personalization on page 5-37.

Headlamp High/ Low-Beam Changer 2 3 (Headlamp High/Low-Beam Changer): Pull the turn signal lever all the way toward you to change the headlamps from low to high beam. Then release it.

This instrument cluster light comes on when the high-beam headlamps are on.

Flash-to-Pass This feature is used to signal to the vehicle ahead that you want to pass. If the headlamps are off or in the low‐beam position, pull the turn signal lever toward you to momentarily switch to high beams.

Release the lever to turn the high-beam headlamps off.

Daytime Running Lamps (DRL) DRL can make it easier for others to see the front of the vehicle during the day. Fully functional DRL are required on all vehicles first sold in Canada. The DRL system comes on in daylight when the following conditions are met:

The ignition is on. The exterior lamp control is in the AUTO position. The shift lever is not in P (Park). The light sensor determines it is daytime.

When the DRL are on, the taillamps, sidemarker, instrument panel lights, and other lamps will not be on.

GMC Savana Owner Manual 2015 - crc - 6/3/14

(GMNA-Localizing-U.S./Canada-7707482)

Black plate (3,1)

The automatic headlamp system automatically switches from DRL to the headlamps depending on the darkness of the surroundings. To turn off the DRL, turn the exterior lamp control to O and then release it. For vehicles first sold in Canada, the transmission must be in the P (Park) position, before the DRL can be turned off.

Automatic Headlamp System When it is dark enough outside and the headlamp switch is in AUTO, the automatic headlamp system turns on the headlamps, along with the taillamps, sidemarker lamps, parking lamps, and the instrument panel lights. The radio lights will also be dim. To turn off the automatic headlamp system, turn the exterior lamp control to the off position and then release. For vehicles first sold in Canada, the transmission must be

in the P (Park) position, before the automatic headlamp system can be turned off.

The vehicle has a light sensor on the top of the instrument panel. Do not cover the sensor; otherwise the system will come on whenever the ignition is on. The system may also turn on the headlamps when driving through a parking garage or tunnel. There is a delay in the transition between the daytime and nighttime operation of the Daytime Running Lamps (DRL) and the automatic headlamp system so that driving under bridges or bright overhead street lights does not affect the

Lighting

6-3

system. The DRL and automatic headlamp system are only affected when the light sensor sees a change in lighting lasting longer than the delay. If the vehicle is started in a dark garage, the automatic headlamp system comes on immediately. Once the vehicle leaves the garage, it takes approximately 30 seconds for the automatic headlamp system to change to DRL if it is light outside. During that delay, the instrument cluster may not be as bright as usual. Make sure the instrument panel brightness control is in the full bright position. See Instrument Panel Illumination Control on page 6-5. Lights On with Wipers If the windshield wipers are activated in daylight with the engine on, and the exterior lamp control is in AUTO, the headlamps, parking lamps, and other exterior lamps come on. The transition time for the lamps coming on varies based on

GMC Savana Owner Manual 2015 - crc - 6/3/14

(GMNA-Localizing-U.S./Canada-7707482)

Black plate (4,1)

6-4

Lighting

wiper speed. When the wipers are not operating, these lamps turn off. Move the exterior lamp control to P or ; to disable this feature.

Hazard Warning Flashers

When the hazard warning flashers are on, the vehicle's turn signals will not work.

Turn and Lane-Change Signals

G (Turn Signals): An arrow on the instrument cluster flashes in the direction of the turn or lane change. To signal a turn, move the lever all the way up or down. To signal a lane change, raise or lower the lever until the arrow starts to flash. The turn signal automatically flashes three times and if the Tow/Haul Mode is active it flashes six times. Holding the turn signal lever for more than

| (Hazard Warning Flashers): Press this button to make the front and rear turn signal lamps flash on and off. This warns others that you are having trouble. Press again to turn the flashers off.

one second causes the turn signals to flash continually until the lever is