2015 GMC Canyon Owners Manual

foot on the accelerator. Cruise control does not work at speeds below about 40 km/h (25 mph).

{ Warning

Cruise control can be dangerous where you cannot drive safely at a steady speed. Do not use cruise control on winding roads or in heavy traffic. Cruise control can be dangerous on slippery roads. On such roads, fast changes in tire traction can cause excessive wheel slip, and you could lose control. Do not use cruise control on slippery roads.

GMC Canyon Owner Manual (GMNA-Localizing-U.S./Canada-7587000) 2015 - CRC - 6/25/14

Black plate (46,1)

9-46

Driving and Operating

If equipped with a manual transmission, the cruise control will remain active when the gears are shifted. The cruise is deactivated if the clutch is pressed for several seconds. If the cruise control is being used and the Traction Control (TCS) system or StabiliTrak begins to limit wheel spin, the cruise control will automatically disengage. See Traction Control/Electronic Stability Control on page 9-42. If a collision alert occurs when cruise control is activated, cruise control is disengaged. See Forward Collision Alert (FCA) System on page 9-48. When road conditions allow you to safely use it again, cruise control can be turned back on. If the brakes are applied, the cruise control disengages.

SET− (Set/Coast): Press briefly to set the speed and activate cruise control. If cruise control is already active, use to decrease vehicle speed. * (Cancel): Press to disengage cruise control without erasing the set speed from memory.

Setting Cruise Control If 5 is on when not in use, SET− or +RES could get pressed and go into cruise when not desired. Keep 5
off when cruise is not being used. 1. Press 5 to turn the cruise

system on.

2. Get up to the desired speed. 3. Press and release SET−. 4. Remove foot from the

accelerator.

5 (On/Off): Press to turn the system on or off. A white indicator comes on in the instrument cluster when cruise control is turned on. +RES (Resume/Accelerate): If there is a set speed in memory, press briefly to resume to that speed or press and hold to accelerate. If cruise control is already active, use to increase vehicle speed.

GMC Canyon Owner Manual (GMNA-Localizing-U.S./Canada-7587000) 2015 - CRC - 6/25/14

Black plate (47,1)

Driving and Operating

9-47

The cruise control indicator on the instrument cluster turns green after cruise control has been set to the desired speed. See Instrument Cluster (Uplevel) on page 5-9 or Instrument Cluster (Base Level) on page 5-8.

Resuming a Set Speed If the cruise control is set at a desired speed and then the brakes are applied or * is pressed, the cruise control is disengaged without erasing the set speed from memory. Once the vehicle speed reaches about 40 km/h (25 mph) or more, press the +RES button briefly. The vehicle returns to the previous set speed.

Increasing Speed While Using Cruise Control If the cruise control system is already activated: . Press and hold +RES until the desired speed is reached, then release it.

To increase vehicle speed in small increments, briefly press +RES. For each press, the vehicle goes about 1.6 km/h (1 mph) faster.

The speedometer reading can be displayed in either English or metric units. See Driver Information Center (DIC) (Base Level) on page 5-25 or Driver Information Center (DIC) (Uplevel) on page 5-28. The increment value used depends on the units displayed.

Reducing Speed While Using Cruise Control If the cruise control system is already activated: . Press and hold SET– until the

desired lower speed is reached, then release it. To slow down in small increments, briefly press SET– . For each press, the vehicle goes about 1.6 km/h (1 mph) slower.

The speedometer reading can be displayed in either English or metric units. See Driver Information Center (DIC) (Base Level) on page 5-25 or Driver Information Center (DIC) (Uplevel) on page 5-28. The increment value used depends on the units displayed.

Passing Another Vehicle While Using Cruise Control Use the accelerator pedal to increase the vehicle speed. When you take your foot off the pedal, the vehicle will slow down to the previous set cruise speed. While pressing the accelerator pedal or shortly following the release to override cruise control, briefly pressing the SET– button will result in cruise control set to the current vehicle speed.

Using Cruise Control on Hills How well the cruise control will work on hills depends on the vehicle speed, load, and the steepness of the hills. When going up steep hills, you might have to step on the

GMC Canyon Owner Manual (GMNA-Localizing-U.S./Canada-7587000) 2015 - CRC - 6/25/14

Black plate (48,1)

9-48

Driving and Operating

accelerator pedal to maintain your speed. When going downhill, you might have to brake or shift to a lower gear to keep your speed down. If the brake pedal is applied, cruise control will disengage.

Ending Cruise Control There are four ways to end cruise control: . Step lightly on the brake pedal. . Press *. . Press the clutch pedal for

several seconds or shift the transmission to N (Neutral). To turn off cruise control, press 5.

Erasing Speed Memory The cruise control set speed is erased from memory if 5 is pressed or if the ignition is turned off.

Driver Assistance Systems

Forward Collision Alert (FCA) System If equipped, the FCA system may help to avoid or reduce the harm caused by front-end crashes. When approaching a vehicle ahead too quickly, FCA provides a red flashing alert on the windshield, and rapidly beeps. FCA also lights an amber visual alert if following another vehicle much too closely. FCA detects vehicles within a distance of approximately 60 m (197 ft) and operates at speeds above 40 km/h (25 mph).

{ Warning

FCA is a warning system and does not apply the brakes. When approaching a slower-moving or stopped vehicle ahead too rapidly, or when following a vehicle too closely, FCA may not provide a warning with enough time to help avoid a crash. FCA does not warn of pedestrians, animals, signs, guardrails, bridges, construction barrels, or other objects. Be ready to take action and apply the brakes. For more information, see Defensive Driving on page 9-3.

FCA can be disabled with the FCA steering wheel control.

GMC Canyon Owner Manual (GMNA-Localizing-U.S./Canada-7587000) 2015 - CRC - 6/25/14

Black plate (49,1)

Detecting the Vehicle Ahead

FCA warnings will not occur unless the FCA system detects a vehicle ahead. When a vehicle is detected, the vehicle ahead indicator will display green. Vehicles may not be detected on curves, highway exit ramps, or hills; or due to poor visibility. FCA will not detect another vehicle ahead until it is completely in the driving lane.

{ Warning

FCA does not provide a warning to help avoid a crash, unless it detects a vehicle. FCA may not detect a vehicle ahead if the FCA sensor is blocked by dirt, snow,

(Continued)

Warning (Continued)

or ice, or if the windshield is damaged. It may also not detect a vehicle on winding or hilly roads, or in conditions that can limit visibility such as fog, rain, or snow, or if the headlamps or windshield are not cleaned or in proper condition. Keep the windshield, headlamps, and FCA sensors clean and in good repair.

Collision Alert

When your vehicle approaches another detected vehicle too rapidly, the red lights will flash on the windshield. Also, eight rapid high-pitched beeps will sound from the front. When this Collision Alert

Driving and Operating

9-49

occurs, the brake system may prepare for driver braking to occur more rapidly which can cause a brief, mild deceleration. Continue to apply the brake pedal as needed. Cruise control may be disengaged when the Collision Alert occurs.

Tailgating Alert

The vehicle ahead indicator will display amber when you are following a detected vehicle ahead much too closely. Selecting the Alert Timing The Collision Alert control is on the steering wheel. Press [ to set the FCA timing to Far, Medium, Near, or Off. The first button press shows the current setting on the DIC. Additional button presses will change this setting. The chosen

GMC Canyon Owner Manual (GMNA-Localizing-U.S./Canada-7587000) 2015 - CRC - 6/25/14

Black plate (50,1)

9-50

Driving and Operating

setting will remain until it is changed and will affect the timing of both the Collision Alert and the Tailgating Alert features. The timing of both alerts will vary based on vehicle speed. The faster the vehicle speed, the farther away the alert will occur. Consider traffic and weather conditions when selecting the alert timing. The range of selectable alert timing may not be appropriate for all drivers and driving conditions. Unnecessary Alerts FCA may provide unnecessary alerts for turning vehicles, vehicles in other lanes, objects that are not vehicles, or shadows. These alerts are normal operation and the vehicle does not need service. Cleaning the System If the FCA system does not seem to operate properly, cleaning the outside of the windshield in front of the rearview mirror, and cleaning the front of the vehicle, may correct the issue.

Rear Vision Camera (RVC)

{ Warning

The RVC system does not display children, pedestrians, bicyclists, crossing traffic, animals, or any other object located outside the camera's field of view, below the bumper, or under the vehicle. Perceived distances may be different from actual distances. Do not back the vehicle using only the RVC screen. Failure to use proper care before backing may result in injury, death, or vehicle damage. Always check behind and around the vehicle before backing.

If equipped, the RVC system is designed to help the driver when backing up by displaying a view of the area behind the vehicle. When the key is in ON/RUN and the driver shifts the vehicle into R (Reverse),

the video image automatically appears on the infotainment screen. The infotainment screen goes to the previous screen after approximately four seconds once the vehicle is shifted out of R (Reverse). To see the previous screen sooner, do one of the following: . Press a hard key on the

infotainment system.

. Shift into P (Park).

Guidelines The RVC system may have a guideline overlay that can help the driver align the vehicle when backing into a parking spot. To turn the guidelines on or off: 1. Shift into P (Park). 2. Press SETTINGS on the home

screen of the infotainment system.

3. Select Rear Camera. 4. Select Guidance Lines, then

select Off or On.

GMC Canyon Owner Manual (GMNA-Localizing-U.S./Canada-7587000) 2015 - CRC - 6/25/14

Black plate (51,1)

Rear Vision Camera Error Messages SERVICE REAR VISION CAMERA SYSTEM: This message can display on the infotainment screen when the system is not working properly. If any other problem occurs or if a problem persists, see your dealer. Rear Vision Camera Location The camera is under the tailgate handle. The area displayed by the camera is limited. It does not display objects that are close to either corner or under the bumper and can vary depending on vehicle orientation or road conditions. Displayed images may be further or closer than they appear. The following illustrations show the field of view that the camera provides.

1. View displayed by the

camera.

1. View displayed by the

camera.

2. Corner of the rear bumper.

Driving and Operating

9-51

When the System Does Not Seem to Work Properly The RVC system may not work properly or display a clear image if:

It is dark. The sun or the beam of headlamps are shining directly into the camera lens. Ice, snow, mud, or anything else builds up on the camera lens. Clean the lens, rinse it with water, and wipe it with a soft cloth. The back of the vehicle is in an accident. The position and mounting angle of the camera can change or the camera can be affected. Be sure to have the camera, its position, and mounting angle checked at your dealer.

GMC Canyon Owner Manual (GMNA-Localizing-U.S./Canada-7587000) 2015 - CRC - 6/25/14

Black plate (52,1)

9-52

Driving and Operating

Disconnecting the Rear Vision Camera (RVC) The RVC must be disconnected if the tailgate needs to be removed.

The RVC is disconnected by disconnecting the connector behind the rear license plate.

Lane Departure Warning (LDW) If equipped, LDW may help avoid crashes due to unintentional lane departures. It may provide an alert if

the vehicle is crossing a lane marking without using a turn signal in that direction. LDW uses a camera sensor to detect the lane markings at speeds of 56 km/h (35 mph) or greater.

{ Warning

The LDW system does not steer the vehicle. The LDW system may not:

. Provide enough time to avoid

a crash.

. Detect lane markings under

poor weather or visibility conditions. This can occur if the windshield or headlamps are blocked by dirt, snow, or ice; if they are not in proper condition; or if the sun shines directly into the camera.

. Detect road edges.

(Continued)

Warning (Continued)

. Detect lanes on winding or

hilly roads.

If LDW only detects lane markings on one side of the road, it will only warn you when departing the lane on the side where it has detected a lane marking. Always keep your attention on the road and maintain proper vehicle position within the lane, or vehicle damage, injury, or death could occur. Always keep the windshield, headlamps, and camera sensors clean and in good repair. Do not use LDW in bad weather conditions.

How the System Works The LDW camera sensor is on the windshield ahead of the rearview mirror.

GMC Canyon Owner Manual (GMNA-Localizing-U.S./Canada-7587000) 2015 - CRC - 6/25/14

Black plate (53,1)

Driving and Operating

9-53

To turn LDW on and off, press @ on the center stack. The control indicator will light when LDW is on.

When LDW is on, @ is green if LDW is available to warn of a lane departure. If the vehicle crosses a detected lane marking without using the turn signal in that direction, @ changes to amber and flashes. Additionally, there will be three beeps on the right or left, depending on the lane departure direction.

When the System Does Not Seem to Work Properly The system may not detect lanes as well when there are: . Close vehicles ahead. . Sudden lighting changes, such

as when driving through tunnels.

. Banked roads. If the LDW system is not functioning properly when lane markings are clearly visible, cleaning the windshield may help. LDW alerts may occur due to tar marks, shadows, cracks in the road, temporary or construction lane markings, or other road imperfections. This is normal system operation; the vehicle does not need service. Turn LDW off if these conditions continue.

Fuel Use of the recommended fuel is an important part of the proper maintenance of this vehicle. When driving in the U.S. and Canada, to help keep the engine clean and maintain optimum vehicle performance, we recommend using TOP TIER Detergent Gasolines. See www.toptiergas.com for a list of TOP TIER Detergent Gasolines.

Use regular unleaded gasoline meeting ASTM specification D4814
with a posted octane rating of 87 or

GMC Canyon Owner Manual (GMNA-Localizing-U.S./Canada-7587000) 2015 - CRC - 6/25/14

Black plate (54,1)

9-54

Driving and Operating

higher. Do not use gasoline with an octane rating below 87, as it may cause engine damage and will lower fuel economy.

Use of Seasonal Fuels Use summer and winter fuels in the appropriate season. The fuels industry automatically modifies the fuel for the appropriate season. If fuel is left in the vehicle tank for long periods of time, driving or starting could be affected. Drive the vehicle until the fuel is at one-half tank or less, then refuel with the current seasonal fuel.

Prohibited Fuels Gasolines containing oxygenates such as ethers and ethanol, as well as reformulated gasolines, are available in some cities. If these gasolines comply with the previously described specification, then they are acceptable to use. However, E85 (85% ethanol) and other fuels containing more than 15% ethanol must be used only in FlexFuel vehicles.

{ Caution

Do not use fuel containing methanol. It can corrode metal parts in the fuel system and also damage plastic and rubber parts. That damage would not be covered under the vehicle warranty.

Some gasolines, mainly high octane racing gasolines, can contain an octane-enhancing additive called methylcyclopentadienyl manganese tricarbonyl (MMT). Do not use gasolines and/or fuel additives with MMT as they can reduce spark plug life and affect emission control system performance. The malfunction indicator lamp may turn on. If this occurs, see your dealer for service.

California Fuel Requirements If the vehicle is certified to meet California Emissions Standards, it is designed to operate on fuels that meet California specifications. See the underhood emission control label. If this fuel is not available in states adopting California Emissions Standards, the vehicle will operate satisfactorily on fuels meeting federal specifications, but emission control system performance might be affected. The malfunction indicator lamp could turn on and the vehicle may not pass a smog-check test. See Malfunction Indicator Lamp on page 5-15. If this occurs, return to your authorized dealer for diagnosis. If it is determined that the condition is caused by the type of fuel used, repairs may not be covered by the vehicle warranty.

GMC Canyon Owner Manual (GMNA-Localizing-U.S./Canada-7587000) 2015 - CRC - 6/25/14

Black plate (55,1)

Driving and Operating

9-55

Fuels in Foreign Countries If planning to drive in countries outside the U.S. or Canada, the proper fuel might be hard to find. Check regional auto club or fuel retail brand websites for availability in the country where driving. Never use leaded gasoline, fuel containing methanol, manganese, or any other fuel not recommended. Costly repairs caused by use of improper fuel would not be covered by the vehicle warranty.

Fuel Additives To keep fuel systems clean, TOP TIER Detergent Gasoline is recommended. See Fuel on page 9-53. If TOP TIER Detergent Gasoline is not available, one bottle of Fuel System Treatment PLUS added to the fuel tank at every engine oil change, can help. Fuel System Treatment PLUS is the only

gasoline additive recommended by General Motors. It is available at your dealer.

Filling the Tank

{ Warning

Fuel vapor burns violently and a fuel fire can cause bad injuries. To help avoid injuries to you and others, read and follow all the instructions on the fuel pump island. Turn off the engine when refueling. Do not smoke near fuel or when refueling the vehicle. Do not use cellular phones. Keep sparks, flames, and smoking materials away from fuel. Do not leave the fuel pump unattended when refueling the vehicle. This is against the law in some places. Do not re-enter the vehicle while pumping fuel. Keep children away from the fuel pump; never let children pump fuel.

The fuel cap is behind a hinged fuel door on the driver side of the vehicle. To open the fuel door, push and release the rearward center edge of the door. To remove the fuel cap, turn it slowly counterclockwise. While refueling, hang the fuel cap from the hook on the fuel door.

GMC Canyon Owner Manual (GMNA-Localizing-U.S./Canada-7587000) 2015 - CRC - 6/25/14

Black plate (56,1)

9-56

Driving and Operating

{ Warning

Fuel can spray out on you if you open the fuel cap too quickly. If you spill fuel and then something ignites it, you could be badly burned. This spray can happen if the tank is nearly full, and is more likely in hot weather. Open the fuel cap slowly and wait for any hiss noise to stop. Then unscrew the cap all the way.

Be careful not to spill fuel. Do not top off or overfill the tank and wait a few seconds after you have finished pumping before removing the nozzle. Clean fuel from painted surfaces as soon as possible. See Exterior Care on page 10-83.

When replacing the fuel cap, turn it clockwise until it clicks. Make sure the cap is fully installed. The diagnostic system can determine if the fuel cap has been left off or improperly installed. This would allow fuel to evaporate into the atmosphere. If the fuel cap is not properly installed, a message appears on the Driver Information Center (DIC) and the check engine light will be lit on the instrument cluster. See Fuel System Messages on page 5-35 and Malfunction Indicator Lamp on page 5-15.

{ Warning

If a fire starts while you are refueling, do not remove the nozzle. Shut off the flow of fuel by shutting off the pump or by notifying the station attendant. Leave the area immediately.

{ Caution

If a new fuel cap is needed, be sure to get the right type of cap from your dealer. The wrong type of fuel cap may not fit properly, may cause the malfunction indicator lamp to light, and could damage the fuel tank and emissions system. See Malfunction Indicator Lamp on page 5-15.

Filling a Portable Fuel Container

{ Warning

Never fill a portable fuel container while it is in the vehicle. Static electricity discharge from the container can ignite the fuel vapor. You can be badly burned

(Continued)

GMC Canyon Owner Manual (GMNA-Localizing-U.S./Canada-7587000) 2015 - CRC - 6/25/14

Black plate (57,1)

Warning (Continued)

and the vehicle damaged if this occurs. To help avoid injury to you and others:

. Dispense fuel only into

approved containers.

. Do not fill a container while it

is inside a vehicle, in a vehicle's trunk, pickup bed, or on any surface other than the ground.

. Bring the fill nozzle in contact

with the inside of the fill opening before operating the nozzle. Contact should be maintained until the filling is complete.

. Do not smoke while

pumping fuel.

. Do not use a cellular phone

while pumping fuel.

Trailer Towing

General Towing Information Only use towing equipment that has been designed for the vehicle. Contact your dealer or trailering dealer for assistance with preparing the vehicle for towing a trailer. Read the entire section before towing a trailer. For towing a disabled vehicle, see Towing the Vehicle on page 10-78. For towing the vehicle behind another vehicle such as a motor home, see Recreational Vehicle Towing on page 10-78.

Driving and Operating

9-57

Driving Characteristics and Towing Tips

Driving with a Trailer When towing a trailer: . Become familiar with the state

and local laws that apply to trailer towing.

. Do not tow a trailer during the first 800 km (500 mi) to prevent damage to the engine, axle, or other parts. Then during the first 800 km (500 mi) of trailer towing, do not drive over 80 km/h (50 mph) and do not make starts at full throttle.

. Vehicles can tow in D (Drive).

Shift the transmission to a lower gear if the transmission shifts too often under heavy loads and/ or hilly conditions. Turn off Park Assist when towing.

GMC Canyon Owner Manual (GMNA-Localizing-U.S./Canada-7587000) 2015 - CRC - 6/25/14

Black plate (58,1)

9-58

Driving and Operating

{ Warning

When towing a trailer, exhaust gases may collect at the rear of the vehicle and enter if the liftgate, trunk/hatch, or rear-most window is open. When towing a trailer:

. Do not drive with the liftgate,

trunk/hatch, or rear-most window open.

. Fully open the air outlets on

or under the instrument panel.

. Also adjust the climate

control system to a setting that brings in only outside air. See “Climate Control Systems” in the Index. For more information about Carbon Monoxide, see Engine Exhaust on page 9-29.

Towing a trailer requires a certain amount of experience. The combination you are driving is longer and not as responsive as the vehicle itself. Get acquainted with the handling and braking of the rig before setting out for the open road. Before starting, check all trailer hitch parts and attachments, safety chains, electrical connectors, lamps, tires, and mirrors. If the trailer has electric brakes, start the combination moving and then apply the trailer brake controller by hand to be sure the brakes work. During the trip, check occasionally to be sure that the load is secure and the lamps and any trailer brakes still work. Following Distance Stay at least twice as far behind the vehicle ahead as you would when driving the vehicle without a trailer. This can help to avoid heavy braking and sudden turns.

Passing More passing distance is needed when towing a trailer. The combination will not accelerate as quickly and is longer so it is necessary to go much farther beyond the passed vehicle before returning to the lane. Backing Up Hold the bottom of the steering wheel with one hand. To move the trailer to the left, move that hand to the left. To move the trailer to the right, move your hand to the right. Always back up slowly and, if possible, have someone guide you. Making Turns

{ Caution

Making very sharp turns while trailering could cause the trailer to come in contact with the vehicle.

(Continued)

GMC Canyon Owner Manual (GMNA-Localizing-U.S./Canada-7587000) 2015 - CRC - 6/25/14

Black plate (59,1)

Vehicles can tow in D (Drive). Shift the transmission to a lower gear if the transmission shifts too often under heavy loads and/or hilly conditions. The Tow/Haul Mode may be used if the transmission shifts too often. See Tow/Haul Mode on page 9-34. When towing at high altitude on steep uphill grades, consider the following: Engine coolant will boil at a lower temperature than at normal altitudes. If the engine is turned off immediately after towing at high altitude on steep uphill grades, the vehicle may show signs similar to engine overheating. To avoid this, let the engine run while parked, preferably on level ground, with the transmission in P (Park) for a few minutes before turning the engine off. If the overheat warning comes on, see Engine Overheating on page 10-18.

Driving and Operating

9-59

Parking on Hills

{ Warning

Parking the vehicle on a hill with the trailer attached can be dangerous. If something goes wrong, the rig could start to move. People can be injured, and both the vehicle and the trailer can be damaged. When possible, always park the rig on a flat surface.

If parking the rig on a hill: 1. Press the brake pedal, but do not shift into P (Park) yet. Turn the wheels into the curb if facing downhill or into traffic if facing uphill.

2. Have someone place chocks

under the trailer wheels.

3. When the wheel chocks are in

place, release the regular brakes until the chocks absorb the load.

Caution (Continued)

The vehicle could be damaged. Avoid making very sharp turns while trailering.

When turning with a trailer, make wider turns than normal. Do this so the trailer will not strike soft shoulders, curbs, road signs, trees, or other objects. Avoid jerky or sudden maneuvers. Signal well in advance. If the trailer turn signal bulbs burn out, the arrows on the instrument cluster will still flash for turns. It is important to check occasionally to be sure the trailer bulbs are still working. Driving on Grades Reduce speed and shift to a lower gear before starting down a long or steep downgrade. If the transmission is not shifted down, the brakes might get hot and no longer work well.

GMC Canyon Owner Manual (GMNA-Localizing-U.S./Canada-7587000) 2015 - CRC - 6/25/14

Black plate (60,1)

9-60

Driving and Operating

4. Reapply the brake pedal. Then

apply the parking brake and shift into P (Park).

5. Release the brake pedal. Leaving After Parking on a Hill 1. Apply and hold the brake pedal. 2. Start the engine. 3. Shift into a gear. 4. Release the parking brake. 5. Let up on the brake pedal. 6. Drive slowly until the trailer is

clear of the chocks.

7. Stop and have someone pick up

and store the chocks.

Maintenance when Trailer Towing The vehicle needs service more often when pulling a trailer. See Maintenance Schedule on page 11-2. Things that are especially important in trailer operation are automatic transmission fluid, engine oil, axle

lubricant, belts, cooling system, and brake system. It is a good idea to inspect these before and during the trip. Check periodically to see that all hitch nuts and bolts are tight.

Trailer Towing Do not tow a trailer during break-in. See New Vehicle Break-In on page 9-21.

{ Warning

The driver can lose control when pulling a trailer if the correct equipment is not used or the vehicle is not driven properly. For example, if the trailer is too heavy, the brakes may not work well or even at all. The driver and passengers could be seriously injured. The vehicle may also be damaged; the resulting repairs would not be covered by the

(Continued)

Warning (Continued)

vehicle warranty. Pull a trailer only if all the steps in this section have been followed. Ask your dealer for advice and information about towing a trailer with the vehicle.

{ Caution

Pulling a trailer improperly can damage the vehicle and result in costly repairs not covered by the vehicle warranty. To pull a trailer correctly, follow the advice in this section and see your dealer for important information about towing a trailer with the vehicle.

GMC Canyon Owner Manual (GMNA-Localizing-U.S./Canada-7587000) 2015 - CRC - 6/25/14

Black plate (61,1)

Driving and Operating

9-61

Trailer Weight Rating (TWR) is calculated assuming the tow vehicle has only the driver but all required trailering equipment. Weight of additional optional equipment, passengers, and cargo in the tow vehicle must be subtracted from the trailer weight rating.

See Vehicle Load Limits on page 9-15 for more information about the vehicle's maximum load capacity. To identify the trailering capacity of the vehicle, read the information in “Weight of the Trailer” later in this section. Trailering is different than just driving the vehicle by itself. Trailering means changes in handling, acceleration, braking, durability, and fuel economy. Successful, safe trailering takes correct equipment, and it has to be used properly.

The following information has many time-tested, important trailering tips and safety rules. Many of these are important for your safety and that of your passengers. Read this section carefully before pulling a trailer. Weight of the Trailer How heavy can a trailer safely be? It depends on how the rig is used. Speed, altitude, road grades, outside temperature, and how much the vehicle is used to pull a trailer are all important. It can depend on any special equipment on the vehicle, and the amount of tongue weight the vehicle can carry. See “Weight of the Trailer Tongue” later in this section for more information.

GMC Canyon Owner Manual (GMNA-Localizing-U.S./Canada-7587000) 2015 - CRC - 6/25/14

Black plate (62,1)

9-62

Driving and Operating

Use the following chart to determine how much the vehicle can weigh, based upon the vehicle model and options.

Engine

Axle Ratio

Maximum Trailer Weight

GCWR (a)

2.5L L4
3.6L V6

3 856 kg (8,500 lb) 5 443 kg (12,000 lb) (a) The Gross Combination Weight Rating (GCWR) is the total allowable weight of the completely loaded vehicle and trailer including any passengers, cargo, equipment, and conversions. The GCWR for the vehicle should not be exceeded.

1 587 kg (3,500 lb) 3 175 kg (7,000 lb)

4.10
3.42

the vehicle can carry, which will also reduce the trailer weight the vehicle can tow.

Ask your dealer for trailering information or advice. Weight of the Trailer Tongue The tongue load (1) of any trailer is very important because it is also part of the vehicle weight. The Gross Vehicle Weight (GVW) includes the curb weight of the vehicle, any cargo carried in it, and the people who will be riding in the vehicle as well as trailer tongue weight. Vehicle options, equipment, passengers and cargo in the vehicle reduce the amount of tongue weight

Trailer tongue weight (1) should be 10–15% of the loaded trailer weight (2) up to 408 kg (900 lb). Trailer rating may be limited by the vehicle's ability to carry tongue weight. Tongue weight cannot cause the vehicle to exceed the GVWR (Gross Vehicle Weight Rating) or the RGAWR (Rear Gross Axle Weight Rating). After loading the trailer, weigh the trailer and then the tongue, separately, to see if the weights are proper. If they are not, adjustments might be made by moving some items around in the trailer.

GMC Canyon Owner Manual (GMNA-Localizing-U.S./Canada-7587000) 2015 - CRC - 6/25/14

Black plate (63,1)

Driving and Operating

9-63

Total Weight on the Vehicle's Tires Be sure the vehicle's tires are inflated to the inflation pressures found on the Certification/Tire label on the center pillar or see Vehicle Load Limits on page 9-15. Make sure not to exceed the GVWR limit for the vehicle, or the RGAWR, with the tow vehicle and trailer fully loaded for the trip including the weight of the trailer tongue. If using a weight-distributing hitch, make sure not to exceed the RGAWR before applying the weight distribution spring bars. Weight of the Trailering Combination It is important that the combination of the tow vehicle and trailer does not exceed any of its weight ratings — GCWR, GVWR, RGAWR, Trailer Weight Rating, or Tongue Weight. The only way to be sure it is not exceeding any of these ratings is to weigh the tow vehicle and trailer

combination, fully loaded for the trip, getting individual weights for each of these items.

Towing Equipment

Hitches The correct hitch equipment helps maintain combination control. Many trailers can be towed with a weight-carrying hitch which simply features a coupler latched to the hitch ball, or a tow eye latched to a pintle hook. Other trailers may require a weight-distributing hitch that uses spring bars to distribute the trailer tongue weight among the tow vehicle and trailer axles. If a step-bumper hitch will be used, the bumper could be damaged in sharp turns. Make sure there is ample room when turning to avoid contact between the trailer and the bumper. A step-bumper hitch is limited to 1587 kg (3,500 lb) total weight.

Consider using sway controls with any trailer. Ask a trailering professional about sway controls or refer to the trailer manufacturer's recommendations and instructions. Weight-Distributing Hitch Adjustment A weight distributing hitch may be useful with some trailers.

1. Body to Ground Distance 2. Front of Vehicle

GMC Canyon Owner Manual (GMNA-Localizing-U.S./Canada-7587000) 2015 - CRC - 6/25/14

Black plate (64,1)

9-64

Driving and Operating

When using a weight-distributing hitch, the spring bars should be adjusted so the distance (1) is the same after coupling the trailer to the tow vehicle and adjusting the hitch. Safety Chains Always attach chains between the vehicle and the trailer. Cross the safety chains under the tongue of the trailer to help prevent the tongue from contacting the road if it becomes separated from the hitch. Instructions about safety chains may be provided by the hitch manufacturer or by the trailer manufacturer. Always leave just enough slack so the combination can turn. Never allow safety chains to drag on the ground. Trailer Brakes A loaded trailer that weighs more than 900 kg (2,000 lb) needs to have its own brake system that is adequate for the weight of the trailer. Be sure to read and follow

the instructions for the trailer brakes so they are installed, adjusted, and maintained properly. Trailer Wiring Harness For vehicles not equipped with heavy-duty trailering, a harness is secured underneath the left side of the vehicle, next to the spare tire. The harness requires the installation of a trailer connector, which is available through your dealer. The seven-wire harness contains the following trailer circuits: . Yellow: Left Stop/Turn Signal . Green: Right Stop/Turn Signal . Brown: Taillamps/Parking Lamps . Black: Ground . Gray: Back-up Lamps . Orange: Battery Feed . Blue: Trailer Brake If charging a remote (non-vehicle) battery, press the Tow/Haul Mode button, if equipped, on the center stack. This will boost the vehicle

system voltage and properly charge the battery. If the trailer is too light for Tow/Haul Mode, or the vehicle is not equipped with Tow/Haul, turn on the headlamps as a second way to boost the vehicle system and charge the battery. Tow/Haul Mode

Press this button on the center stack to turn on and off the Tow/ Haul Mode.

GMC Canyon Owner Manual (GMNA-Localizing-U.S./Canada-7587000) 2015 - CRC - 6/25/14

Black plate (65,1)

Driving and Operating

9-65

. When pulling a heavy trailer or a

large or heavy load in stop-and-go traffic.

. When pulling a heavy trailer or a

large or heavy load in busy parking lots where improved low speed control of the vehicle is desired.

Operating the vehicle in Tow/Haul when lightly loaded or with no trailer at all will not cause damage. However, there is no benefit to the selection of Tow/Haul when the vehicle is unloaded. Such a selection when unloaded may result in unpleasant engine and transmission driving characteristics and reduced fuel economy. Tow/ Haul is recommended only when pulling a heavy trailer or a large or heavy load.

Trailer Sway Control (TSC) Vehicles with StabiliTrak have a TSC feature. Trailer sway is unintended side-to-side motion of a

trailer while being towed. If the vehicle is towing a trailer and the TSC detects that sway is increasing, the vehicle brakes are selectively applied at each wheel, to help reduce excessive trailer sway. If TSC is enabled, the Traction Control System (TCS)/StabiliTrak warning light will flash on the instrument cluster. Vehicle speed must be reduced. If trailer sway continues, StabiliTrak can reduce engine torque to help slow the vehicle. See Traction Control/ Electronic Stability Control on page 9-42.

{ Warning

Even if the vehicle is equipped with TSC, trailer sway could result in loss of control and the vehicle could crash. If excessive trailer sway is detected, slow down to a safe speed. Check the trailer and vehicle to help correct possible

(Continued)

This indicator light on the instrument cluster comes on when the Tow/ Haul Mode is on. Tow/Haul is a feature that assists when pulling a heavy trailer or a large or heavy load. See Tow/Haul Mode on page 9-34. Tow/Haul is designed to be most effective when the vehicle and trailer combined weight is at least 75 percent of the vehicle's Gross Combined Weight Rating (GCWR). See “Weight of the Trailer” under Trailer Towing on page 9-60. Tow/ Haul is most useful under the following driving conditions: . When pulling a heavy trailer or a

large or heavy load through rolling terrain.

GMC Canyon Owner Manual (GMNA-Localizing-U.S./Canada-7587000) 2015 - CRC - 6/25/14

Black plate (66,1)

9-66

Driving and Operating

Warning (Continued)

causes. These could include an improperly or overloaded trailer, unrestrained cargo, improper trailer hitch configuration, excessive vehicle-trailer speed, or improperly inflated or incorrect vehicle or trailer tires. See Towing Equipment on page 9-63 for trailer ratings and hitch setup recommendations.

Adding non-dealer accessories can affect the vehicle performance. See Accessories and Modifications on page 10-3.

Conversions and Add-Ons

Add-On Electrical Equipment

{ Caution

Some electrical equipment can damage the vehicle or cause components to not work and would not be covered by the warranty. Always check with your dealer before adding electrical equipment.

Add-on equipment can drain the vehicle's 12-volt battery, even if the vehicle is not operating. The vehicle has an airbag system. Before attempting to add anything electrical to the vehicle, see Servicing the Airbag-Equipped Vehicle on page 3-26 and Adding Equipment to the Airbag-Equipped Vehicle on page 3-27.

GMC Canyon Owner Manual (GMNA-Localizing-U.S./Canada-7587000) 2015 - CRC - 6/25/14

Black plate (1,1)

Vehicle Care

10-1

Vehicle Care

General Information

General Information . . . . . . . . . . 10-2
California Proposition

65 Warning . . . . . . . . . . . . . . . . . 10-2

California Perchlorate

Materials Requirements . . . . 10-3

Accessories and

Modifications . . . . . . . . . . . . . . . 10-3

Vehicle Checks Doing Your Own

Service Work . . . . . . . . . . . . . . . 10-3
Hood . . . . . . . . . . . . . . . . . . . . . . . . 10-4
Engine Compartment

Overview . . . . . . . . . . . . . . . . . . . 10-5
Engine Oil . . . . . . . . . . . . . . . . . . . 10-8
Engine Oil Life System . . . . . 10-10
Automatic Transmission

Fluid . . . . . . . . . . . . . . . . . . . . . . 10-12

Manual Transmission

Fluid . . . . . . . . . . . . . . . . . . . . . . 10-12
Hydraulic Clutch . . . . . . . . . . . . 10-12
Engine Air Cleaner/Filter . . . . 10-13
Cooling System . . . . . . . . . . . . 10-15
Engine Coolant . . . . . . . . . . . . . 10-16
Engine Overheating . . . . . . . . 10-18

Engine Fan . . . . . . . . . . . . . . . . . 10-20
Washer Fluid . . . . . . . . . . . . . . . 10-20
Brakes . . . . . . . . . . . . . . . . . . . . . 10-21
Brake Fluid . . . . . . . . . . . . . . . . . 10-21
Battery . . . . . . . . . . . . . . . . . . . . . 10-23
Four-Wheel Drive . . . . . . . . . . . 10-24
Front Axle . . . . . . . . . . . . . . . . . . 10-24
Rear Axle . . . . . . . . . . . . . . . . . . 10-25
Starter Switch Check . . . . . . . 10-26
Automatic Transmission Shift

Lock Control Function Check . . . . . . . . . . . . . . . . . . . . . 10-27

Ignition Transmission Lock

Check . . . . . . . . . . . . . . . . . . . . . 10-27

Park Brake and P (Park)

Mechanism Check . . . . . . . . 10-27

Wiper Blade

Replacement . . . . . . . . . . . . . . 10-28

Headlamp Aiming

Headlamp Aiming . . . . . . . . . . 10-29

Bulb Replacement

Bulb Replacement . . . . . . . . . . 10-29
Halogen Bulbs . . . . . . . . . . . . . . 10-29
Headlamps, Front Turn

Signal, Sidemarker, and Parking Lamps . . . . . . . . . . . . 10-29

Taillamps, Turn Signal,

Stoplamps, and Back-Up Lamps . . . . . . . . . . . . . . . . . . . . 10-30

Center High-Mounted

Stoplamp (CHMSL) and Cargo Lamp . . . . . . . . . . . . . . 10-31
Replacement Bulbs . . . . . . . . . 10-32

Electrical System

Electrical System

Overload . . . . . . . . . . . . . . . . . . 10-32
Fuses . . . . . . . . . . . . . . . . . . . . . . 10-33
Engine Compartment Fuse

Block . . . . . . . . . . . . . . . . . . . . . 10-33

Instrument Panel Fuse

Block . . . . . . . . . . . . . . . . . . . . . 10-38

Wheels and Tires

Tires . . . . . . . . . . . . . . . . . . . . . . . . 10-40
All-Season Tires . . . . . . . . . . . . 10-41
Winter Tires . . . . . . . . . . . . . . . . 10-42
All-Terrain Tires . . . . . . . . . . . . 10-42
Tire Sidewall Labeling . . . . . . 10-42
Tire Designations . . . . . . . . . . . 10-45
Tire Terminology and

Definitions . . . . . . . . . . . . . . . . 10-45
Tire Pressure . . . . . . . . . . . . . . . 10-48
Tire Pressure Monitor

System . . . . . . . . . . . . . . . . . . . 10-50

GMC Canyon Owner Manual (GMNA-Localizing-U.S./Canada-7587000) 2015 - CRC - 6/25/14

Black plate (2,1)

10-2

Vehicle Care

Appearance Care

Exterior Care . . . . . . . . . . . . . . . 10-83
Interior Care . . . . . . . . . . . . . . . . 10-88
Floor Mats . . . . . . . . . . . . . . . . . . 10-91

General Information For service and parts needs, visit your dealer. You will receive genuine GM parts and GM-trained and supported service people. Genuine GM parts have one of these marks:

Tire Pressure Monitor

Operation . . . . . . . . . . . . . . . . . 10-51
Tire Inspection . . . . . . . . . . . . . . 10-54
Tire Rotation . . . . . . . . . . . . . . . 10-54
When It Is Time for New

Tires . . . . . . . . . . . . . . . . . . . . . . 10-56
Buying New Tires . . . . . . . . . . . 10-57
Different Size Tires and

Wheels . . . . . . . . . . . . . . . . . . . 10-58

Uniform Tire Quality

Grading . . . . . . . . . . . . . . . . . . . 10-59

Wheel Alignment and Tire

Balance . . . . . . . . . . . . . . . . . . . 10-60
Wheel Replacement . . . . . . . . 10-61
Tire Chains . . . . . . . . . . . . . . . . . 10-61
If a Tire Goes Flat . . . . . . . . . . 10-62
Tire Changing . . . . . . . . . . . . . . 10-64
Compact Spare Tire . . . . . . . . 10-73
Full-Size Spare Tire . . . . . . . . 10-74

Jump Starting

Jump Starting . . . . . . . . . . . . . . 10-75

Towing the Vehicle

Towing the Vehicle . . . . . . . . . 10-78
Recreational Vehicle

Towing . . . . . . . . . . . . . . . . . . . . 10-78

California Proposition 65 Warning Most motor vehicles, including this one, contain and/or emit chemicals known to the State of California to

GMC Canyon Owner Manual (GMNA-Localizing-U.S./Canada-7587000) 2015 - CRC - 6/25/14

Black plate (3,1)

cause cancer and birth defects or other reproductive harm. Engine exhaust, many parts and systems, many fluids, and some component wear by-products contain and/or emit these chemicals.

California Perchlorate Materials Requirements Certain types of automotive applications, such as airbag initiators, safety belt pretensioners, and lithium batteries contained in Remote Keyless Entry transmitters, may contain perchlorate materials. Special handling may be necessary. For additional information, see www.dtsc.ca.gov/hazardouswaste/ perchlorate.

Accessories and Modifications Adding non‐dealer accessories or making modifications to the vehicle can affect vehicle performance and safety, including such things as airbags, braking, stability, ride and

handling, emissions systems, aerodynamics, durability, and electronic systems like antilock brakes, traction control, and stability control. These accessories or modifications could even cause malfunction or damage not covered by the vehicle warranty. Damage to vehicle components resulting from modifications or the installation or use of non‐GM certified parts, including control module or software modifications, is not covered under the terms of the vehicle warranty and may affect remaining warranty coverage for affected parts. GM Accessories are designed to complement and function with other systems on the vehicle. See your dealer to accessorize the vehicle using genuine GM Accessories installed by a dealer technician. Also, see Adding Equipment to the Airbag-Equipped Vehicle on page 3-27.

Vehicle Care

10-3

Vehicle Checks

Doing Your Own Service Work

{ Warning

It can be dangerous to work on your vehicle if you do not have the proper knowledge, service manual, tools, or parts. Always follow owner manual procedures and consult the service manual for your vehicle before doing any service work.

If doing some of your own service work, use the proper service manual. It tells you much more about how to service the vehicle than this manual can. To order the proper service manual, see Service Publications Ordering Information on page 13-11.

GMC Canyon Owner Manual (GMNA-Localizing-U.S./Canada-7587000) 2015 - CRC - 6/25/14

Black plate (4,1)

10-4

Vehicle Care

This vehicle has an airbag system. Before attempting to do your own service work, see Servicing the Airbag-Equipped Vehicle on page 3-26. Keep a record with all parts receipts and list the mileage and the date of any service work performed. See Maintenance Records on page 11-15.

{ Caution Even small amounts of contamination can cause damage to vehicle systems. Do not allow contaminants to contact the fluids, reservoir caps, or dipsticks.

Hood To open the hood:

1. Pull the hood release lever with this symbol on it. It is inside the vehicle to the lower left of the steering wheel.

2. Go to the front of the vehicle to find the secondary hood release handle. The handle is under the front edge of the hood near the center. Push the handle to the right and at the same time raise the hood.

To close the hood: 1. Before closing the hood, be sure

all the filler caps are properly installed.

2. Lower the hood to 20 cm (8 in) above the vehicle and release it so it fully latches. Check to make sure the hood is firmly closed by lifting up on the front edge of the hood. Repeat the process if necessary.

GMC Canyon Owner Manual (GMNA-Localizing-U.S./Canada-7587000) 2015 - CRC - 6/25/14

Black plate (5,1)

Engine Compartment Overview

Vehicle Care

10-5

2.5L L4 Engine

GMC Canyon Owner Manual (GMNA-Localizing-U.S./Canada-7587000) 2015 - CRC - 6/25/14

Black plate (6,1)

10-6

Vehicle Care

1. Coolant Surge Tank and

Pressure Cap. See Engine Coolant on page 10-16.

4. Engine Cooling Fan (Out of

View). See Cooling System on page 10-15.

2. Engine Air Cleaner/Filter on

5. Engine Oil Dipstick. See Engine

page 10-13.

Oil on page 10-8.

3. Engine Oil Fill Cap. See Engine

6. Engine Compartment Fuse

Oil on page 10-8.

Block on page 10-33.

7. Brake/Clutch Fluid Reservoir.

See Brake Fluid on page 10-21
or Hydraulic Clutch on page 10-12 (If Equipped). 8. Windshield Washer Fluid

Reservoir. See Washer Fluid on page 10-20.

9. Battery on page 10-23.

GMC Canyon Owner Manual (GMNA-Localizing-U.S./Canada-7587000) 2015 - CRC - 6/25/14

Black plate (7,1)

Vehicle Care

10-7

3.6L V6 Engine

GMC Canyon Owner Manual (GMNA-Localizing-U.S./Canada-7587000) 2015 - CRC - 6/25/14

Black plate (8,1)

10-8

Vehicle Care

1. Coolant Surge Tank and

Pressure Cap. See Engine Coolant on page 10-16.

2. Engine Air Cleaner/Filter on

page 10-13.

3. Engine Cooling Fan (Out of

View). See Cooling System on page 10-15.

4. Engine Oil Fill Cap. See Engine

Oil on page 10-8.

5. Engine Oil Dipstick. See Engine

Oil on page 10-8.

6. Engine Compartment Fuse

Block on page 10-33.

7. Brake Fluid Reservoir. See Brake Fluid on page 10-21.

8. Windshield Washer Fluid

Reservoir. See Washer Fluid on page 10-20.

9. Battery on page 10-23.

Engine Oil To ensure proper engine performance and long life, careful attention must be paid to engine oil. Following these simple, but important steps will help protect your investment: . Always use engine oil approved to the proper specification and of the proper viscosity grade. See “Selecting the Right Engine Oil” in this section.

. Check the engine oil level regularly and maintain the proper oil level. See “Checking Engine Oil” and “When to Add Engine Oil” in this section.

. Change the engine oil at the

appropriate time. See Engine Oil Life System on page 10-10. . Always dispose of engine oil

properly. See “What to Do with Used Oil” in this section.

Checking Engine Oil It is a good idea to check the engine oil level at each fuel fill. In order to get an accurate reading, the vehicle must be on level ground. The engine oil dipstick handle is a yellow loop. See Engine Compartment Overview on page 10-5 for the location of the engine oil dipstick. Obtaining an accurate oil level reading is essential: 1.

If the engine has been running recently, turn off the engine and allow several minutes for the oil to drain back into the oil pan. Checking the oil level too soon after engine shutoff will not provide an accurate oil level reading.

2. Pull out the dipstick and wipe it

with a clean paper towel or cloth, then push it back in all the way. Remove it again, keeping the tip down, and check the level.

GMC Canyon Owner Manual (GMNA-Localizing-U.S./Canada-7587000) 2015 - CRC - 6/25/14

Black plate (9,1)

Vehicle Care

10-9

Selecting the Right Engine Oil Selecting the right engine oil depends on both the proper oil specification and viscosity grade. See Recommended Fluids and Lubricants on page 11-12.

Specification Ask for and use engine oils that meet the dexos1™ specification. Engine oils that have been approved by GM as meeting the dexos1 specification are marked with the dexos1 approved logo. See www.gmdexos.com.

When to Add Engine Oil

{ Caution

L4 Engine

V6 Engine

If the oil is below the cross-hatched area at the tip of the dipstick, add 1 L (1 qt) of the recommended oil and then recheck the level. See “Selecting the Right Engine Oil” in this section for an explanation of what kind of oil to use. For engine oil crankcase capacity, see Capacities and Specifications on page 12-2.

Do not add too much oil. Oil levels above or below the acceptable operating range shown on the dipstick are harmful to the engine. If you find that you have an oil level above the operating range, i.e., the engine has so much oil that the oil level gets above the cross-hatched area that shows the proper operating range, the engine could be damaged. You should drain out the excess oil or limit driving of the vehicle and seek a service professional to remove the excess amount of oil.

See Engine Compartment Overview on page 10-5 for the location of the engine oil fill cap. Add enough oil to put the level somewhere in the proper operating range. Push the dipstick all the way back in when through.

GMC Canyon Owner Manual (GMNA-Localizing-U.S./Canada-7587000) 2015 - CRC - 6/25/14

Black plate (10,1)

10-10

Vehicle Care

{ Caution

Failure to use the recommended engine oil can result in engine damage not covered by the vehicle warranty. Check with your dealer or service provider on whether the oil is approved to the dexos1 specification.

Viscosity Grade Use SAE 5W-30 viscosity grade engine oil for the 3.6L V6 engine. Use SAE 5W-20 viscosity grade engine oil for the 2.5L L4 engine. Cold Temperature Operation: In an area of extreme cold, where the temperature falls below −29°C (−20°F), an SAE 0W-30 oil may be used for the 3.6L V6 engine and SAE 0W-20 viscosity grade engine oil may be used for the 2.5L L4
engine. An oil of this viscosity grade will provide easier cold starting for the engine at extremely low temperatures. When selecting an oil

of the appropriate viscosity grade, always select an oil of the correct specification. See “Specification” earlier in this section for more information. Engine Oil Additives/Engine Oil Flushes Do not add anything to the oil. The recommended oils meeting the dexos1 specification are all that is needed for good performance and engine protection. Engine oil system flushes are not recommended and could cause engine damage not covered by the vehicle warranty. What to Do with Used Oil Used engine oil contains certain elements that can be unhealthy for your skin and could even cause cancer. Do not let used oil stay on your skin for very long. Clean your skin and nails with soap and water, or a good hand cleaner. Wash or properly dispose of clothing or rags

containing used engine oil. See the manufacturer's warnings about the use and disposal of oil products. Used oil can be a threat to the environment. If you change your own oil, be sure to drain all the oil from the filter before disposal. Never dispose of oil by putting it in the trash or pouring it on the ground, into sewers, or into streams or bodies of water. Recycle it by taking it to a place that collects used oil.

Engine Oil Life System

When to Change Engine Oil This vehicle has a computer system that indicates when to change the engine oil and filter. This is based on a combination of factors which include engine revolutions, engine temperature, and miles driven. Based on driving conditions, the mileage at which an oil change is indicated can vary considerably. For the oil life system to work properly, the system must be reset every time the oil is changed.

GMC Canyon Owner Manual (GMNA-Localizing-U.S./Canada-7587000) 2015 - CRC - 6/25/14

Black plate (11,1)

On some vehicles, when the system has calculated that oil life has been diminished, a CHANGE ENGINE OIL SOON message comes on to indicate that an oil change is necessary. See Engine Oil Messages on page 5-34. Change the oil as soon as possible within the next 1 000 km (600 mi). It is possible that, if driving under the best conditions, the oil life system might indicate that an oil change is not necessary for up to a year. The engine oil and filter must be changed at least once a year and, at this time, the system must be reset. For vehicles without the CHANGE ENGINE OIL SOON message, an oil change is needed when the OIL LIFE REMAINING percentage is near 0%. Your dealer has trained service people who will perform this work and reset the system. It is also important to check the oil regularly over the course of an oil drain interval and keep it at the proper level.

If the system is ever reset accidentally, the oil must be changed at 5 000 km (3,000 mi) since the last oil change. Remember to reset the oil life system whenever the oil is changed. How to Reset the Engine Oil Life System Reset the system whenever the engine oil is changed so that the system can calculate the next engine oil change. Always reset the engine oil life to 100% after every oil change. It will not reset itself. To reset the engine oil life system: 1. Display OIL LIFE REMAINING

on the DIC. See Driver Information Center (DIC) (Base Level) on page 5-25 or Driver Information Center (DIC) (Uplevel) on page 5-28. If the vehicle does not have DIC buttons, the vehicle must be in P (Park) to access this display.

Vehicle Care

10-11

2. Press and hold the V button on the DIC, or the SET/CLR button on the turn signal lever if the vehicle does not have DIC buttons, for several seconds. The oil life will change to 100%. The oil life system can also be reset as follows: 1. Turn the ignition to ON/RUN with

the engine off.

2. Fully press the accelerator pedal

slowly three times within five seconds.

3. Display OIL LIFE REMAINING

on the DIC. If the display shows 100%, the system is reset. If the vehicle has a CHANGE ENGINE OIL SOON message and it comes back on when the vehicle is started and/or the OIL LIFE REMAINING is near 0%, the engine oil life system has not been reset. Repeat the procedure.

GMC Canyon Owner Manual (GMNA-Localizing-U.S./Canada-7587000)