2006 GMC Canyon Owners Manual

Download PDF Manual
If you have to leave your vehicle with the engine running, be sure your vehicle is in PARK (P) and your parking brake is ﬁrmly set before you leave it. After you have moved the shift lever into PARK (P), hold the regular brake pedal down. Then, see if you can move the shift lever away from PARK (P) without ﬁrst pulling it toward you. If you can, it means that the shift lever was not fully locked into PARK (P). Torque Lock (Automatic Transmission) If you are parking on a hill and you do not shift your transmission into PARK (P) properly, the weight of the vehicle may put too much force on the parking pawl in the transmission. You may ﬁnd it difficult to pull the shift lever out of PARK (P). This is called torque lock. To prevent torque lock, set the parking brake and then shift into PARK (P) properly before you leave the driver’s seat. To ﬁnd out how, see Shifting Into Park (P) (Automatic Transmission) on page 2-29. When you are ready to drive, move the shift lever out of PARK (P) before you release the parking brake. If torque lock does occur, you may need to have another vehicle push yours a little uphill to take some of the pressure from the parking pawl in the transmission, so you can pull the shift lever out of PARK (P). Shifting Out of Park (P) (Automatic Transmission) Your vehicle has an automatic transmission shift lock control system which locks the shift lever in PARK (P) when the ignition is in the LOCK position. In addition, you have to fully apply the regular brakes before you can shift from PARK (P) when the ignition is in ON. See Automatic Transmission Operation on page 2-20. 2-30 If you cannot shift out of PARK (P), ease pressure on the shift lever by pushing the shift lever all the way into PARK (P) as you maintain brake application. Then, move the shift lever into the gear you want. If you ever hold the brake pedal down but still cannot shift out of PARK (P), try this: 1. Turn the key to ACC. There is no shift interlock in this key position. 2. Apply and hold the brake until the end of Step 4. 3. Shift the transmission to NEUTRAL (N). 4. Start the vehicle and then shift to the gear you want. 5. Have the system ﬁxed as soon as you can. Parking Your Vehicle (Manual Transmission) Your vehicle has a manual transmission. Before you get out of your vehicle, move the shift lever into REVERSE (R), and ﬁrmly apply the parking brake. Once the shift lever has been placed into REVERSE (R) with the clutch pedal pressed in, turn the ignition key to LOCK, remove the key and release the clutch. If you are parking on a hill, or if your vehicle is pulling a trailer, see Towing a Trailer on page 4-56. Parking Over Things That Burn {CAUTION: Things that can burn could touch hot exhaust parts under your vehicle and ignite. Do not park over papers, leaves, dry grass, or other things that can burn. 2-31 Running the Engine While Parked It is better not to park with the engine running. But if you ever have to, here are some things to know. {CAUTION: Idling the engine with the climate control system off could allow dangerous exhaust into your vehicle. See the earlier caution under Engine Exhaust on page 2-32. Also, idling in a closed-in place can let deadly carbon monoxide (CO) into your vehicle even if the climate control fan is at the highest setting. One place this can happen is a garage. Exhaust — with CO — can come in easily. NEVER park in a garage with the engine running. Another closed-in place can be a blizzard. See Winter Driving on page 4-38. Engine Exhaust {CAUTION: Engine exhaust can kill. It contains the gas carbon monoxide (CO), which you cannot see or smell. It can cause unconsciousness and death. You might have exhaust coming in if: (cid:127) Your exhaust system sounds strange or different. (cid:127) Your vehicle gets rusty underneath. (cid:127) Your vehicle was damaged in a collision. (cid:127) Your vehicle was damaged when driving over high points on the road or over road debris. (cid:127) Repairs were not done correctly. (cid:127) Your vehicle or exhaust system had been modiﬁed improperly. If you ever suspect exhaust is coming into your vehicle: (cid:127) Drive it only with all the windows down to blow out any CO; and (cid:127) Have your vehicle ﬁxed immediately. 2-32 {CAUTION: {CAUTION: It can be dangerous to get out of your vehicle if the automatic transmission shift lever is not fully in PARK (P) with the parking brake ﬁrmly set. Your vehicle can roll. Do not leave your vehicle when the engine is running unless you have to. If you have left the engine running, the vehicle can move suddenly. You or others could be injured. To be sure your vehicle will not move, even when it is on fairly level ground, always set the parking brake and move the automatic transmission shift lever to PARK (P), or the manual transmission shift lever to NEUTRAL. Four-wheel drive vehicles with the transfer case in NEUTRAL will allow the vehicle to roll, even if your automatic transmission shift lever is in PARK (P). So, be sure the transfer case is in a drive gear — not in NEUTRAL. Always set your parking brake. Follow the proper steps to be sure your vehicle will not move. See Shifting Into Park (P) (Automatic Transmission) on page 2-29. If you are pulling a trailer, see Towing a Trailer on page 4-56. 2-33 Mirrors Manual Rearview Mirror While sitting in a comfortable driving position, adjust the outside rearview mirror so you can see clearly behind your vehicle. Grip the mirror in the center to move it up or down and side to side. The control at the bottom of the mirror is the day/night feature that allows adjustment to the mirror so that the glare of headlamps from behind is reduced. Push the control for daytime use; pull it for night use. The mirror may have lamps. Press the button next to each lamp to turn it on or off. Manual Rearview Mirror with OnStar® Mirror Operation Your vehicle may have a manual rearview mirror with the OnStar® System and map lamps. You can adjust the mirror for day or night driving. Press the tab forward (away from you) for day driving. Pull the tab back (toward you) for night driving. There are also three OnStar® buttons located at the bottom of the mirror. See your dealer for more information on the system and how to subscribe to OnStar®. See OnStar® System on page 2-38 for more information about the services OnStar® provides. Map Lamps The mirror has map lamps located at the bottom of the mirror. To manually turn the lamps on or off, press the button next to each lamp. Cleaning the Mirror When cleaning the mirror, use a paper towel or similar material dampened with glass cleaner. Do not spray glass cleaner directly on the mirror housing. 2-34 Automatic Dimming Rearview Mirror with Compass and Temperature Display The vehicle may have an automatic dimming rearview mirror with a compass, temperature display, and map lamps. Mirror Operation The mirror automatically changes to reduce glare from headlamps behind you. A time delay feature prevents rapid changing from the day to night positions while driving under lights and through traffic. P (On/Off): The automatic dimming feature is automatically activated when the vehicle is started. The automatic dimming feature is turned on or off by pressing this button located on the lower part of the mirror. Press and hold the button for up to three seconds to turn this feature on or off. T (Indicator Light): This light will turn on when the automatic dimming feature is active. Map Lamps The mirror has map lamps located at the bottom of the mirror. To manually turn the lamps on or off, press the button next to each lamp. Compass Operation The mirror has an eight-point compass display in the bottom of the mirror face. When the ignition and the compass feature are on, the compass will show two character boxes for approximately two seconds. After two seconds, the mirror will display the current compass heading. For example, NE is displayed for north-east. Compass Calibration If after two seconds the display does not show a compass heading, there may be a strong magnetic ﬁeld interfering with the compass. Such interference may be caused by a magnetic antenna mount, note pad holder or similar object. If the letter C appears in the compass window, the compass needs calibration. The mirror compass can be calibrated by driving the vehicle in circles at 5 mph (8 km/h) or less until the display reads a direction. The compass can be placed in calibration mode by pressing and holding the left map light button until a C appears on the compass display. 2-35 Compass Variance Compass variance is the difference between earth’s magnetic north and true geographic north. If the mirror is not adjusted for compass variance, your compass could give false readings. The mirror is set in zone eight upon leaving the factory. It will be necessary to adjust the compass to compensate for compass variance if you live outside zone eight. Under certain circumstances, such as a long distance, cross-country trip, it will be necessary to adjust the compass variance. To adjust for compass variance, do the following: 1. Find your current location and variance zone number on the zone map that follows. 2-36 2. Press and hold the left map light button until a zone number appears on the display. 3. Once the zone number appears on the display, press the on/off button quickly until you reach the correct zone number. Stop pressing the button and the mirror will return to normal operation. If C appears in the compass window, the compass may need calibration. See “Compass Calibration” listed previously. Temperature Display Operation The outside air temperature is displayed in the window located at the lower center of the mirror face. Press and hold the far right button for four seconds and release. This will change the temperature reading between degrees Fahrenheit, degrees Celsius, or turn the display off. Cleaning the Mirror When cleaning the mirror, use a paper towel or similar material dampened with glass cleaner. Do not spray glass cleaner directly on the mirror as that may cause the liquid cleaner to enter the mirror housing. Outside Manual Mirrors If the vehicle has manual outside mirrors, adjust them by hand so that the side of the vehicle can be seen while you are sitting in a comfortable driving position. The mirrors can be folded inward to prevent damage when going through an automatic car wash. To fold, push the mirror toward the vehicle. To return the mirror to its original position, push outward. Return both mirrors to the unfolded position before driving. Outside Power Mirrors If your vehicle has this feature, the controls are located on the driver’s door armrest. To adjust the power mirrors, do the following: 1. Move the selector switch to the L (left) or R (right) to choose the driver’s or passenger’s mirror. 2. Use the arrows located on the four-way control pad to move the mirror in the direction you want the mirror to go. 3. Return the selector switch to the center position once the mirrors are adjusted. 2-37 If the mirror begins making a ratcheting sound, the mirror has reached the end of its travel and can go no farther in that direction. To stop the sound, reverse the mirror direction using the control pad. The mirrors can be manually folded inward to prevent damage when going through an automatic car wash. To fold, push the mirror toward the vehicle. To return the mirror to its original position, push outward. Be sure to return both mirrors to the unfolded position before driving. Outside Convex Mirror Your passenger’s outside rearview mirror is convex. A convex mirror’s surface is curved so you can see more from the driver’s seat. {CAUTION: A convex mirror can make things (like other vehicles) look farther away than they really are. If you cut too sharply into the right lane, you could hit a vehicle on your right. Check your inside mirror or glance over your shoulder before changing lanes. 2-38 OnStar® System OnStar® uses global positioning system (GPS) satellite technology, wireless communications, and live advisors to provide you with a wide range of safety, security, information, and convenience services. If your airbags deploy, the system is designed to make an automatic call to OnStar® Emergency where we can request emergency services be sent to your location. If you lock your keys in the car, call OnStar® at 1-888-4-ONSTAR and they can send a signal to unlock your doors. If you need roadside assistance, press the OnStar® button and they will get you the help you need. A complete OnStar® User’s Guide and the Terms and Conditions of the OnStar® Subscription Service Agreement are included in the vehicle’s glove box literature. For more information, visit www.onstar.com or www.onstar.ca. Contact OnStar® at 1-888-4-ONSTAR (1-888-466-7827), or press the OnStar® button to speak to an OnStar® advisor 24 hours a day, 7 days a week. Terms and conditions of the Subscription Service Agreement can be found at www.onstar.com or www.onstar.ca. OnStar® Services For new vehicles equipped with OnStar®, the Safe and Sound Plan is included for one year from the date of purchase. You can extend this plan beyond the ﬁrst year, or upgrade to the Directions and Connections® Plan to meet your needs. For more information, press the OnStar® button to speak to an advisor. Safe and Sound Plan (cid:127) Automatic Notiﬁcation of Airbag Deployment (cid:127) Emergency Services (cid:127) Roadside Assistance (cid:127) Stolen Vehicle Tracking (cid:127) AccidentAssist (cid:127) Remote Door Unlock/Vehicle Alert (cid:127) Remote Diagnostics (cid:127) Online Concierge Directions and Connections® Plan (cid:127) All Safe and Sound Plan Services (cid:127) Driving Directions (cid:127) RideAssist Information and Convenience Services OnStar® Personal Calling As an OnStar® subscriber, the Personal Calling capability allows you to make hands-free calls using a wireless system that is integrated into the vehicle. Calls can be placed nationwide using simple voice commands with no additional contracts and no additional roaming charges. To ﬁnd out more about OnStar® Personal Calling, refer to the OnStar® User’s Guide in the vehicle’s glove box, visit www.onstar.com or www.onstar.ca, or speak to an OnStar® advisor by pressing the OnStar® button or calling 1-888-4-ONSTAR (1-888-466-7827). OnStar® Virtual Advisor Your vehicle may have Virtual Advisor. It is a feature of OnStar® Personal Calling that uses your minutes to access weather, local traffic reports, and stock quotes. By pressing the phone button and giving a few simple voice commands, you can browse through the various topics. Customize your information proﬁle at www.myonstar.com. See the OnStar® user’s guide for more information. 2-39 (cid:127) Storage Areas Glove Box To open the glove box, pull on the lever. Cupholder(s) Your vehicle may have two cupholders located on the lower part of the front doors as well as two cupholders located at the front end of the console. Vehicles with bench seats may have cupholders attached to the front of the center seat. If your vehicle is an extended cab or crew cab model, your vehicle also has two rear cupholders. On crew cab models, the cupholders are located at the front end of the rear center seat cushion. On extended cab models, the rear seat cupholders are located on top of the rear center console. If you have an ashtray, it will use one of the cupholders. Front Armrest Storage Area For vehicles with bench seats, you may have a center armrest storage area. Lift up on the upper tab located at the front of the armrest to release the latch. Lift the lid to open the storage area. For vehicles with bucket seats or uplevel packages, your vehicle may have a two-tiered center armrest storage area. Lift up on the upper tab located at the front of the armrest to release the latch. Lift the lid to the top storage area. A second tab is located below the top one and allows you to access the bottom storage area. Lift up on the lower tab to release the latch. Then, raise the lid of the lower storage area. The upper storage area will lift up with the lid of the lower storage area. To close the storage area(s), lower the lid(s) until you feel the latch close. 2-40 Assist Handles Your vehicle may have assist handles to be used when getting out of your vehicle. If your vehicle has assist handles, they are located above the front passenger door if you have a regular cab, or above the front and rear passenger doors if you have an extended cab or crew cab. If your vehicle is equipped with roof-mounted side impact air bags, there will be assist handles located above both the driver’s and front passenger’s doors. Rear Storage Area If your vehicle is an extended cab model, it may be equipped with storage compartments under the rear seats. To access the storage compartments you will need to lift the cushion on the bottom of the rear seats. This will expose the storage boxes under the seat. 2-41 To open a storage box, unhook the bottom and lift the two latches on each side of the storage box. Lift the lid from the center area to access the storage box. 2-42 Section 3 Instrument Panel Instrument Panel Overview ...............................3-4 Hazard Warning Flashers ................................3-6 Other Warning Devices ...................................3-6 Horn .............................................................3-6 Tilt Wheel .....................................................3-7 Turn Signal/Multifunction Lever .........................3-7 Turn and Lane-Change Signals ........................3-8 Headlamp High/Low-Beam Changer ..................3-9 Flash-to-Pass .................................................3-9 Windshield Wipers ........................................3-10 Windshield Washer .......................................3-10 Cruise Control ..............................................3-11 Exterior Lamps .............................................3-14 Headlamps on Reminder ................................3-15 Daytime Running Lamps (DRL) .......................3-15 Automatic Headlamp System ..........................3-15 Fog Lamps ..................................................3-16 Exterior Cargo Lamps ....................................3-17 Interior Lamps ..............................................3-17 Instrument Panel Brightness ...........................3-17 Dome Lamp .................................................3-17 Dome Lamp Override ....................................3-17 Exit Lighting .................................................3-18 Battery Run-Down Protection ..........................3-18 Accessory Power Outlet(s) .............................3-18 Ashtray(s) and Cigarette Lighter ......................3-19 Climate Controls ............................................3-19 Climate Control System .................................3-19 Outlet Adjustment .........................................3-21 Warning Lights, Gages, and Indicators ............3-22 Instrument Panel Cluster ................................3-23 Speedometer and Odometer ...........................3-24 Trip Odometer ..............................................3-24 Tachometer .................................................3-24 Safety Belt Reminder Light .............................3-25 Passenger Safety Belt Reminder Light .............3-25 Airbag Readiness Light ..................................3-26 Passenger Airbag Status Indicator ...................3-27 Battery Warning Light ....................................3-29 Up-Shift Light (Manual Transmission) ...............3-30 Brake System Warning Light ..........................3-30 Anti-Lock Brake System Warning Light .............3-31 Engine Coolant Temperature Gage ..................3-32 Malfunction Indicator Lamp .............................3-32 Oil Pressure Light .........................................3-36 Security Light ...............................................3-37 Cruise Control Light ......................................3-37 Highbeam On Light .......................................3-37 Daytime Running Lamps (DRL) Indicator Light .....3-38 Fuel Gage ...................................................3-38 3-1 Section 3 Instrument Panel Driver Information Center (DIC) .......................3-39 DIC Controls and Displays .............................3-39 DIC Warnings and Messages .........................3-42 Audio System(s) .............................................3-46 Setting the Time for Radios without Radio Data Systems (RDS) ..................................3-47 Setting the Time for Radios with Radio Data Systems (RDS) ..................................3-48 AM-FM Radio ...............................................3-48 Radio with CD (MP3) ....................................3-51 Radio with Six-Disc CD .................................3-66 Theft-Deterrent Feature (Non-RDS Radios) .......3-77 Theft-Deterrent Feature (RDS Radios) .............3-77 Radio Reception ...........................................3-78 Care of Your CDs .........................................3-78 Care of the CD Player ...................................3-79 Fixed Mast Antenna ......................................3-79 XM™ Satellite Radio Antenna System .............3-79 Chime Level Adjustment ................................3-79 3-2 ✍ NOTES 3-3 Instrument Panel Overview Manual Transmission shown, Automatic Transmission similar 3-4 The main components of your vehicle’s instrument panel are the following: A. Air Outlets. See Outlet Adjustment on page 3-21. B. Turn Signal/Multifunction Lever. See Turn Signal/Multifunction Lever on page 3-7. C. Instrument Panel Cluster. See Instrument Panel Cluster on page 3-23. D. Hazard Warning Flasher Button. See Hazard Warning Flashers on page 3-6. E. Passenger Side Airbag. See Airbag System on page 1-63. F. Exterior Lamp Controls. See Exterior Lamps on page 3-14. Fog Lamps (If Equipped). See Fog Lamps on page 3-16. Exterior Cargo Lamps. See Exterior Cargo Lamps on page 3-17. G. Parking Brake Release. See Parking Brake on page 2-28. H. Horn. See Horn on page 3-6. I. Traction Control Button or Four-Wheel Drive Buttons. See Traction Control System (TCS) on page 4-9 and Four-Wheel Drive on page 2-24. J. Audio System. See Audio System(s) on page 3-46. K. Cigarette Lighter (If Equipped). See Ashtray(s) and Cigarette Lighter on page 3-19. L. Climate Control System. See Climate Control System on page 3-19. M. Accessory Power Outlet. See Accessory Power Outlet(s) on page 3-18. N. Passenger Air Bag Status Indicator. See Passenger Airbag Status Indicator on page 3-27. O. Glove Box. See Glove Box on page 2-40. 3-5 Hazard Warning Flashers Your hazard warning ﬂashers let you warn others. They also let police know you have a problem. Your front and rear turn signal lamps will ﬂash on and off. Other Warning Devices If you carry reﬂective triangles, you can set one up at the side of the road about 300 feet (100 m) behind your vehicle. The hazard warning ﬂasher button is located on the instrument panel, between the two air vents in the center. Horn To sound the horn, press the horn symbol on the steering wheel pad. Your hazard warning ﬂashers work no matter what position your key is in, and even if the key isn’t in. Press the button to make the front and rear turn signal lamps ﬂash on and off. Press the button again to turn the ﬂashers off. When the hazard warning ﬂashers are on, your turn signals won’t work. 3-6 Tilt Wheel A tilt wheel allows you to adjust the steering wheel before you drive. If you have the tilt steering wheel, you can raise it to the highest level to allow more room for the driver to enter and exit the vehicle. Turn Signal/Multifunction Lever The tilt lever is located on the left side of the steering column, under the turn signal lever. To tilt, hold the steering wheel and pull the tilt lever toward you. Move the wheel to a comfortable level, then release the tilt lever to lock the wheel in place. Do not adjust the steering wheel while driving. The lever on the left side of the steering column includes the following: (cid:127) G Turn and Lane Change Signals. See Turn Signal/Multifunction Lever on page 3-7. (cid:127) 53 Headlamp High/Low-Beam Changer. See Headlamp High/Low-Beam Changer on page 3-9. Flash-to-Pass. See Flash-to-Pass on page 3-9. (cid:127) N Windshield Wipers. See Windshield Wipers on page 3-10. (cid:127) L Windshield Washer. See Windshield Washer (cid:127) J Cruise Control. See Cruise Control on on page 3-10. page 3-11. 3-7 (cid:127) Turn and Lane-Change Signals The turn signal has two upward (for right) and two downward (for left) positions. These positions allow you to signal a turn or a lane change. To signal a turn, move the lever all the way up or down. When the turn is ﬁnished, the lever will automatically return to the off position. To signal a lane change, raise or lower the lever until the arrow starts to ﬂash. Hold it there until the change is completed. The lever will return by itself when released. An arrow on the instrument panel cluster will ﬂash in the direction of the turn or lane change. As you signal a turn or a lane change, if the arrows ﬂash more quickly than normal, a signal bulb may be burned out and other drivers will not see your vehicle’s turn signal. If a bulb is burned out, replace it to help avoid an accident. If the arrows do not go on at all when signaling a turn, check for a burned-out bulb or a blown fuse. For bulb replacement, see Taillamps, Turn Signal, Stoplamps and Back-up Lamps on page 5-51. For a blown fuse or circuit breaker, see Fuses and Circuit Breakers on page 5-102 Turn Signal On Chime If a turn signal is left on for more than 3/4 of a mile (1.2 km), a chime will sound at each ﬂash of the turn signal and the message TURN SIGNAL will also appear in the DIC. To turn the chime and message off, move the turn signal lever to the off position. See “TURN SIGNAL” under DIC Warnings and Messages on page 3-42 DIC Warnings and Messages for more information. 3-8 Headlamp High/Low-Beam Changer 53(Headlamp High/Low Beam Changer): To change the headlamps from low to high beam, push the lever toward the instrument panel. To return to low-beam headlamps, pull the multifunction lever toward you. Then release it. When the high beams are on, this indicator light on the instrument panel cluster will also be on. Flash-to-Pass This feature lets you use your high-beam headlamps to signal a driver in front of you that you want to pass. It works even if your headlamps are in the automatic position. To use it, pull the turn signal lever toward you, then release it. If your headlamps are in the automatic position or on low beam, your high-beam headlamps will turn on. They’ll stay on as long as you hold the lever toward you. The high-beam indicator on the instrument panel cluster will come on. Release the lever to return to normal operation. 3-9 Windshield Wipers You control the windshield wipers by turning the band with the wiper symbol on it. The windshield wipers work in all ignition positions, except off. This includes the Retained Access Power mode. See Retained Accessory Power (RAP) on page 2-17. 8(Mist): For a single wiping cycle, turn the band to mist. Hold it there until the wipers start. Then let go. The wipers will stop after one wipe. If you want more wipes, hold the band on mist longer. N(Delay): You can set the wiper speed for a long or short delay between wipes. This can be very useful in light rain or snow. Turn the band to choose the delay time. The closer to the top of the lever, the shorter the delay. 6 (Low Speed): For steady wiping at low speed, turn the band away from you to the ﬁrst solid position past the delay settings. 1 (High Speed): For high-speed wiping, turn the band to the second solid position past the delay settings. 9(Off): To stop the wipers, move the band to off. 3-10 Be sure to clear ice and snow from the wiper blades before using them. If they’re frozen to the windshield, carefully loosen or thaw them. If your blades do become worn or damaged, get new blades or blade inserts. Windshield Washer {CAUTION: In freezing weather, do not use your washer until the windshield is warmed. Otherwise the washer ﬂuid can form ice on the windshield, blocking your vision. QL(Washer Fluid): There is a paddle marked with the windshield washer symbol at the top of the multifunction lever. To spray washer ﬂuid on the windshield, push the paddle. The wipers will clear the window and then either stop or return to your preset speed. Cruise Control Your vehicle may be equipped with cruise control. Cruise control will not work if your parking brake is set, or if the master cylinder brake ﬂuid level is low. If you apply your brakes, the cruise control will shut off. 9(Off): This position turns the system off. {CAUTION: R(On): This position activates the system. + (Resume/Accelerate): Move the lever to this symbol to make the vehicle accelerate or resume to a previously set speed. rT(Set): Press this button to set the speed. With cruise control, you can maintain a speed of about 25 mph (40 km/h) or more without keeping your foot on the accelerator. This can really help on long trips. Cruise control does not work at speeds below about 25 mph (40 km/h). Cruise control can be dangerous where you cannot drive safely at a steady speed. So, do not use your cruise control on winding roads or in heavy traffic. Cruise control can be dangerous on slippery roads. On such roads, fast changes in tire traction can cause needless wheel spinning, and you could lose control. Do not use cruise control on slippery roads. If your vehicle is in cruise control when the traction control system (if equipped) begins to limit wheel spin, the cruise control will automatically disengage. See Traction Control System (TCS) on page 4-9. When road conditions allow you to safely use it again, you may turn cruise control back on. 3-11 Setting Cruise Control {CAUTION: If you leave your cruise control on when you are not using cruise, you might hit a button and go into cruise when you do not want to. You could be startled and even lose control. Keep the cruise control switch off until you want to use cruise control. 1. Move the cruise control switch to on. 2. Get up to the speed you want. 3. Press in the set button at the end of the lever and release it. 4. Take your foot off the accelerator pedal. The cruise symbol on the instrument panel will illuminate when the cruise control is engaged. Resuming a Set Speed Suppose you set your cruise control at a desired speed and then you apply the brake. This, of course, disengages the cruise control. But you don’t need to reset it. Once you’re going about 25 mph (40 km/h) or more, you can move the cruise control switch brieﬂy from on to resume/accelerate. You’ll go right back up to your chosen speed and stay there. If you hold the switch at resume/accelerate the vehicle will keep going faster until you release the switch or apply the brake. So unless you want to go faster, don’t hold the switch at resume/accelerate. 3-12 Increasing Speed While Using Cruise Control There are two ways to go to a higher speed: (cid:127) Use the accelerator pedal to get to the higher speed. Press the set button at the end of the lever, then release the button and the accelerator pedal. You’ll now cruise at the higher speed. If the accelerator pedal is held longer than 60 seconds, cruise control will turn off. (cid:127) Move the cruise switch from on to resume/accelerate. Hold it there until you get up to the speed you want, and then release the switch. To increase your speed in very small amounts, move the switch brieﬂy to resume/accelerate. Reducing Speed While Using Cruise Control (cid:127) Press and hold the set button until you reach the lower speed you want, then release it. To slow down in very small amounts, brieﬂy press the set button. Passing Another Vehicle While Using Cruise Control Use the accelerator pedal to increase your speed. When you take your foot off the pedal, your vehicle will slow down to the cruise control speed you set earlier. Using Cruise Control on Hills How well your cruise control will work on hills depends upon your speed, load and the steepness of the hills. When going up steep hills, you may want to step on the accelerator pedal to maintain your speed. When going downhill, you may have to brake or shift to a lower gear to keep your speed down. Of course, applying the brake takes you out of cruise control. Many drivers ﬁnd this to be too much trouble and don’t use cruise control on steep hills. Ending Cruise Control To turn off the cruise control, do one of the following: (cid:127) Step lightly on the brake pedal. (cid:127) Move the cruise control switch to off. Lightly tap or press the clutch, if you have a manual transmission. Erasing Speed Memory When you turn off the cruise control or the ignition, your cruise control set speed memory is erased. 3-13 (cid:127) (cid:127) Exterior Lamps The control on the driver’s side of your instrument panel operates the exterior lamps. O(Exterior Lamps): Turn the knob, located to the right of this symbol, to choose one of the four exterior lamp positions. 9(Off): Turn the knob to this position to turn off all exterior lamps including the DRLs. 3-14 AUTO: Turn the knob to this position to automatically turn on the headlamps at normal brightness, together with the following: (cid:127) Sidemarker Lamps Taillamps (cid:127) Parking Lamps Instrument Panel Lights See Automatic Headlamp System on page 3-15 for more information. ;(Parking Lamps): Turn the knob to this position to turn on the parking lamps, together with the following: (cid:127) Sidemarker Lamps Taillamps License Plate Lamps Instrument Panel Lights 2(Headlamps): Turn the knob to this position to turn on the headlamps, together with the previously listed lamps and lights. You can switch your headlamps from low to high beam by pushing the turn signal/multifunction lever toward the instrument panel. (cid:127) (cid:127) (cid:127) (cid:127) (cid:127) Headlamps on Reminder If a door is open, a reminder chime will sound when your headlamps or parking lamps are manually turned on and your key is out of the ignition. To turn off the chime, turn the headlamp switch to off and then back on. In the automatic mode, the headlamps turn off once the ignition is in LOCK. If your vehicle was ﬁrst sold in Canada and the parking lamps are turned on manually, the DRL will stay on. Daytime Running Lamps (DRL) Daytime Running Lamps (DRL) can make it easier for others to see the front of your vehicle during the day. DRL can be helpful in many different driving conditions, but they can be especially helpful in the short periods after dawn and before sunset. Fully functional daytime running lamps are required on all vehicles ﬁrst sold in Canada. The DRL system will come on when the following conditions are met: The ignition is on. The exterior lamps control is in AUTO. The transmission is not in PARK (P) if you have an automatic transmission. The light sensor determines it is daytime. Your vehicle will have either the parking lamps or reduced intensity low beams used as the DRL. When the DRL are on, only those lamps will be on. The taillamps, sidemarkers, and other lamps will not be on. The instrument panel will not be lit up either. When it begins to get dark, the headlamps will automatically switch from DRL to the regular headlamps. As with any vehicle, you should turn on the regular headlamp system when you need it. Automatic Headlamp System When it is dark enough outside, your automatic headlamp system will turn on your headlamps at the normal brightness along with other lamps such as the taillamps, sidemarker, parking lamps, roof marker lamps and the instrument panel lights. The radio lights will become more dim when the headlights are off compared to when the headlights are on. Your vehicle has a light sensor located on the top of the instrument panel. Be sure it is not covered, or the system will be on whenever the ignition is on. The system may also turn on your headlamps when driving through a parking garage, heavy overcast weather or a tunnel. This is normal. 3-15 (cid:127) (cid:127) (cid:127) (cid:127) There is a delay in the transition between the daytime and nighttime operation of the Daytime Running Lamps (DRL) and the automatic headlamp system so that driving under bridges or bright overhead street lights does not affect the system. The DRL and automatic headlamp system will only be affected when the light sensor sees a change in lighting lasting longer than the delay. If you start your vehicle in a dark garage, the automatic headlamp system will come on immediately. Once you leave the garage, it will take approximately one minute for the automatic headlamp system to change to DRL if it is light outside. During that delay, your instrument panel cluster may not be as bright as usual. Make sure your instrument panel brightness control is in the full bright position. See Instrument Panel Brightness on page 3-17. Fog Lamps If your vehicle has fog lamps, you can use them for better vision in foggy or misty conditions. Your parking lamps and/or low-beam headlamps must be on for your fog lamps to work. The fog lamp button is located near the exterior lamps control. Press the button to turn the fog lamps on while the headlamps or parking lamps are on. Press the button again to turn them off. An indicator light will glow in the button when the fog lamps are on. Remember, fog lamps alone will not give off as much light as your headlamps. Never use your fog lamps in the dark without turning on the headlamps. The fog lamps will go off whenever your high-beam headlamps come on. When the high beams go off, the fog lamps will come on again. Some localities have laws that require the headlamps to be on along with the fog lamps. 3-16 Exterior Cargo Lamps You can use the cargo lamps if you need more light in the cargo area of your vehicle or in the top-box storage units. Press this button, located on the driver side of the instrument panel near the exterior lamp control to turn the cargo lamps on and off. You must have your dome lamps on for your cargo lamps to come on. See Dome Lamp on page 3-17. Interior Lamps The thumbwheel for the interior lamps is located next to the exterior lamps control. See Exterior Lamps on page 3-14 for additional information on location. Instrument Panel Brightness D (Instrument Panel Lights): Turn the thumbwheel up or down to brighten or dim the instrument panel lights and the radio display. This will only work if the headlamps or parking lamps are on. See Exterior Lamps on page 3-14. Dome Lamp The dome lamp will come on when a door is opened. They will shut off several seconds after all doors are closed. You can also turn the dome lamp on manually by turning the interior lamps thumbwheel all the way up. In this position, the dome lamp will remain on whether a door is opened or closed. See Interior Lamps on page 3-17 for additional information on location. Dome Lamp Override E (Dome Override): Press this button, located below the exterior lamp control, to turn the dome lamp off even when a door is opened. See Exterior Lamps on page 3-14 for more information on location. To return the lamp to automatic operation, press the button again. 3-17 Exit Lighting With exit lighting, the interior lamps will come on when you remove the key from the ignition. The lamps will not come on if the dome override button is pressed in. Battery Run-Down Protection This feature shuts off the dome lamp if it is left on for more than 20 minutes when the ignition is in LOCK. This will help prevent your battery from running down. Accessory Power Outlet(s) Your vehicle may have accessory power outlets. With accessory power outlets you can plug in auxiliary electrical equipment such as a cellular telephone or CB radio. Your vehicle may have two accessory power outlets located on the lower part of the instrument panel below the climate control system and there may be one located on the rear of the center console. A small cap must be pulled down to access an accessory power outlet. When not using an outlet be sure to cover it with the protective cap. Notice: Leaving electrical equipment on for extended periods will drain the battery. Always turn off electrical equipment when not in use and do not plug in equipment that exceeds the maximum amperage rating. Certain electrical accessories may not be compatible with the accessory power outlet and could result in blown vehicle or adapter fuses. If you experience a problem, see your dealer for additional information on accessory power outlets. Notice: Adding any electrical equipment to your vehicle may damage it or keep other components from working as they should. The repairs would not be covered by your warranty. Do not use equipment exceeding maximum amperage rating. Check with your dealer before adding electrical equipment. When adding electrical equipment, be sure to follow the proper installation instructions included with the equipment. Notice: damage not covered by your warranty. Do not hang any type of accessory or accessory bracket from the plug because the power outlets are designed for accessory power plugs only. Improper use of the power outlet can cause 3-18 If you put papers, pins, or other ﬂammable Ashtray(s) and Cigarette Lighter Your vehicle may have an ashtray and cigarette lighter. Your ashtray is located in your center console area. The ashtray can be removed for cleaning. When the ashtray is removed, this area can also be used as a cupholder. Notice: items in the ashtray, hot cigarettes or other smoking materials could ignite them and possibly damage your vehicle. Never put ﬂammable items in the ashtray. To use the lighter, press it in all the way, and let go. When it’s ready, it will pop back out by itself. Notice: Holding a cigarette lighter in while it is heating will not allow the lighter to back away from the heating element when it is hot. Damage from overheating may occur to the lighter or heating element, or a fuse could be blown. Do not hold a cigarette lighter in while it is heating. Climate Controls Climate Control System Uplevel Climate Controls shown, Base similar With this system you can control the heating, cooling, and ventilation for your vehicle. Temperature Knob The left knob on the control panel is used to adjust the temperature of the air in the vehicle. Turn the knob clockwise or counterclockwise to increase or decrease the temperature. 3-19 Fan Knob 9 (Fan): The center knob on the control panel is used to control the fan speed. Turn the knob clockwise or counterclockwise to increase or decrease the fan speed. If the knob is set on “0” (zero), some outside air will still enter the vehicle and will be directed according to the position of the mode knob. Mode Knob The right knob on the control panel is used to direct the airﬂow inside your vehicle. Turn the knob to select one of the following modes: H (Vent): Select this mode to direct air to the instrument panel outlets. \(Bi-Level): Select this mode to direct approximately half of the air to the instrument panel outlets, and the remaining air to the ﬂoor outlets and the defroster and side window outlets. Cooler air is directed to the upper outlets and warmer air to the ﬂoor outlets. [ (Floor): Select this mode to direct air to the ﬂoor outlets. Recirculation is disabled in this mode because interior window could fog under some conditions. If this occurs, see “Defogging and Defrosting” following. 3-20 Mode Buttons @ (Recirculation): If your vehicle has air conditioning, you will have the recirculation feature. This mode recirculates air inside the cabin, and prevents outside air from coming in the vehicle. It can be used to prevent outside odors from entering your vehicle and cool the air inside your vehicle more quickly. Press this button to turn the recirculation mode on or off. An indicator light on the button will come on to let you know the recirculation mode is activated. Recirculation is only available in the bi-level and vent modes. It should only be used while in bi-level and vent modes. Recirculation is not available, and the light will not come on or ﬂash while in heat, ﬂoor, ﬂoor/defog, or defrost modes. #(Air Conditioning): Your vehicle may have air conditioning. Press this button to turn the air-conditioning system on or off. An indicator light on the button will come on to let you know the air conditioning is activated. When the system is on, this setting cools and dehumidiﬁes the air entering your vehicle. The air conditioning will not function if the fan is turned off. You may notice a slight change in engine performance when the air conditioning compressor shuts off and turns on again. This is normal. The system is designed to make adjustments to help with fuel economy while still maintaining the selected temperature. The air conditioning system removes moisture from the air, so you may sometimes notice a small amount of water dripping underneath your vehicle while idling or after turning off the engine. This is normal. Defogging and Defrosting Fog on the inside of windows is a result of high humidity (moisture) condensing on the cool window glass. This can be minimized if the climate control system is used properly. There are two modes to clear fog or frost from your windshield and side windows. Use the defog mode to clear the windows of fog or moisture and warm the passengers. Use the defrost mode to remove fog or frost from the windshield more quickly. For best results, clear all snow and ice from the windshield before defrosting. Turn the mode knob on the climate control panel clockwise to select the defog or defrost modes. /(Floor/Defog): This mode directs the air to the windshield, the side window outlets, and to the ﬂoor outlets. When you select this mode, the system runs the air conditioning compressor unless the outside temperature is near freezing or below. Recirculation is not available in this mode. 0 (Defrost): This mode directs most of the air to the windshield, and the side window outlets. When you select this mode, the system runs the air conditioning compressor unless the outside temperature is near, or below freezing. Recirculation is not available in this mode. Do not drive the vehicle until all the windows are clear. Outlet Adjustment Use the thumbwheel on the outlets to change the direction of the air ﬂow. Lift up or push down on the thumbwheel located in the center of the outlet to direct the air up or down, or slide the thumbwheel to the left or right to direct the airﬂow from side-to-side. Operation Tips (cid:127) Clear away any ice, snow or leaves from the air inlets at the base of the windshield that may block the ﬂow of air into your vehicle. (cid:127) Use of non-GM approved hood deﬂectors may adversely affect the performance of the system. (cid:127) Keep the path under the front seats clear of objects to help circulate the air inside of your vehicle more effectively. 3-21 Warning Lights, Gages, and Indicators This part describes the warning lights and gages that may be on your vehicle. The pictures will help you locate them. Warning lights and gages can signal that something is wrong before it becomes serious enough to cause an expensive repair or replacement. Paying attention to your warning lights and gages could also save you or others from injury. Warning lights come on when there may be or is a problem with one of your vehicle’s functions. As you will see in the details on the next few pages, some warning lights come on brieﬂy when you start the engine just to let you know they are working. If you are familiar with this section, you should not be alarmed when this happens. Gages can indicate when there may be or is a problem with one of your vehicle’s functions. Often gages and warning lights work together to let you know when there is a problem with your vehicle. When one of the warning lights comes on and stays on when you are driving, or when one of the gages shows there may be a problem, check the section that tells you what to do about it. Please follow this manual’s advice. Waiting to do repairs can be costly — and even dangerous. So please get to know your warning lights and gages. They are a big help. Your vehicle has a DIC that works along with the warning lights and gages. See Driver Information Center (DIC) on page 3-39 for more information. 3-22 Instrument Panel Cluster Your instrument panel cluster is designed to let you know at a glance how your vehicle is running. You will know how fast you are going, about how much fuel you have used, and many other things you will need to know to drive safely and economically. United States automatic transmission version shown, Canada similar 3-23 Speedometer and Odometer Your speedometer lets you see your speed in both miles per hour (mph) and kilometers per hour (km/h). Your odometer shows how far your vehicle has been driven, in either miles (used in the United States) or kilometers (used in Canada). The odometer mileage can be checked without the vehicle running. Simply press the trip information stem. See “Odometer” under DIC Controls and Displays on page 3-39 for more information. You may wonder what happens if your vehicle needs a new odometer installed. If the new one can be set to the mileage total of the old odometer, then it must be. But if it cannot, then it is set at zero, and a label must be put on the driver’s door to show the old mileage reading when the new odometer was installed. Trip Odometer Your vehicle has a trip odometer that can tell you how far your vehicle has been driven since you last set the trip odometer to zero. See “Trip Odometer” under DIC Controls and Displays on page 3-39 for more information. Tachometer The tachometer displays the engine speed in revolutions per minute (rpm). Notice: tachometer in the shaded warning area, your vehicle could be damaged, and the damages would not be covered by your warranty. Do not operate the engine with the tachometer in the shaded warning area. If you operate the engine with the 3-24 Safety Belt Reminder Light When the key is turned to ON or START, a chime will be provided for several seconds to remind people to buckle their safety belts. The driver safety belt light will also be provided and stay on for several seconds, then it will ﬂash for several more. You should buckle your seat belt. This chime and light will be repeated if the driver remains unbuckled and the vehicle is in motion. If the driver’s belt is buckled, neither the chime nor the light will be provided. Passenger Safety Belt Reminder Light Several seconds after the key is turned to ON or START, a chime will sound for several seconds to remind the front passenger to buckle their safety belt. This would only occur if the passenger airbag is enabled. See Passenger Sensing System on page 1-72 for more information. The passenger safety belt light will also come on and stay on for several seconds, then it will ﬂash for several more. You should have the passenger buckle their seat belt. This chime and light will be repeated if the passenger remains unbuckled and the vehicle is in motion. If the passenger’s safety belt is buckled, neither the chime nor the light will come on. 3-25 {CAUTION: If the airbag readiness light stays on after you start your vehicle, it means the airbag system may not be working properly. The airbags in your vehicle may not inﬂate in a crash, or they could even inﬂate without a crash. To help avoid injury to yourself or others, have your vehicle serviced right away if the airbag readiness light stays on after you start your vehicle. The airbag readiness light should ﬂash for a few seconds when you turn the ignition key to ON. If the light does not come on then, have it ﬁxed so it will be ready to warn you if there is a problem. Airbag Readiness Light There is an airbag readiness light on the instrument panel, which shows the airbag symbol. The system checks the airbag’s electrical system for malfunctions. The light tells you if there is an electrical problem. The system check includes the airbag sensors, the airbag modules, the wiring and the crash sensing and diagnostic module. For more information on the airbag systems, see Airbag System on page 1-63. This light will come on when you start your vehicle, and it will ﬂash for a few seconds. Then the light should go out. This means the system is ready. If the airbag readiness light stays on after you start the vehicle or comes on when you are driving, your airbag system may not work properly. Have your vehicle serviced right away. 3-26 Passenger Airbag Status Indicator Your vehicle has the passenger sensing system. Your instrument panel has a passenger airbag status indicator. United States Canada When the ignition key is turned to ON or START, the passenger airbag status indicator will light ON and OFF, or the symbol for on and off, for several seconds as a system check. Then, after several more seconds, the status indicator will light either ON or OFF, or either the on or off symbol to let you know the status of the right front passenger’s frontal airbag. If your vehicle has a rear seat that will accommodate a rear-facing child restraint, there is a label on your sun visor that says, “Never put a rear-facing child seat in the front.” This is because the risk to the rear-facing child is so great if the airbag deploys. {CAUTION: Even though the passenger sensing system is designed to turn off the passenger’s frontal airbag if the system detects a rear-facing child restraint, no system is failsafe, and no one can guarantee that an airbag will not deploy under some unusual circumstance, even though it is turned off. We recommend that rear-facing child restraints be secured in the rear seat, even if the airbag is off. If your vehicle does not have a rear seat that will accommodate a rear-facing child restraint, never put a child in a rear-facing child restraint in the right front passenger seat the unless passenger airbag status indicator shows off. 3-27 Never put a rear facing child restraint in the right front passenger seat unless the airbag is off. Here is why: {CAUTION: {CAUTION: Even though the passenger sensing system is designed to turn off the passenger’s frontal airbag if the system detects a rear-facing child restraint, no system is fail-safe, and no one can guarantee that an airbag will not deploy under some unusual circumstance, even though it is turned off. We recommend that rear-facing child restraints be transported in vehicles with a rear seat that will accommodate a rear-facing child restraint, whenever possible. If the on indicator comes on when you have a rear-facing child restraint installed in the right front passenger’s seat, it means that the passenger sensing system has not turned off the passenger’s frontal airbag. A child in a rear-facing child restraint can be seriously injured or killed if the right front passenger’s airbag inﬂates. This is because the back of the rear-facing child restraint would be very close to the inﬂating airbag. Do not use a rear-facing child restraint in the right front passenger’s seat if the airbag is turned on. If the word ON or the on symbol is lit on the passenger airbag status indicator, it means that the right front passenger’s frontal airbag is enabled (may inﬂate). If the word OFF or the off symbol is lit on the airbag status indicator, it means that the passenger sensing system has turned off the right front passenger’s frontal airbag. See Passenger Sensing System on page 1-72 for more on this, including important safety information. 3-28 If, after several seconds, all status indicator lights remain on, or if there are no lights at all, there may be a problem with the lights or the passenger sensing system. See your dealer for service. {CAUTION: If the off indicator and the airbag readiness light ever come on together, it means that something may be wrong with the airbag system. If this ever happens, have the vehicle serviced promptly, because an adult-size person sitting in the right front passenger seat may not have the protection of the frontal airbag. See Airbag Readiness Light on page 3-26. Battery Warning Light This light will come on brieﬂy when you start the vehicle, as a check to show you it is working; then it should go out. If it stays on, or comes on while you are driving, you may have a problem with the electrical charging system. Have it checked right away. Driving while this light is on could drain your battery and result in a vehicle that may stall. See DIC Warnings and Messages on page 3-42 for more information. If you must drive a short distance with the light on, be certain to turn off all your accessories, such as the radio and climate control system. 3-29 Up-Shift Light (Manual Transmission) This light appears when you need to shift to the next higher gear on a manual transmission vehicle. Brake System Warning Light Your vehicle’s hydraulic brake system is divided into two parts. If one part is not working, the other part can still work and stop you. For good braking, though, you need both parts working well. If the warning light comes on, there could be a brake problem. Have your brake system inspected right away. Shifting when the indicator light is on will help you get the best fuel economy. See “Up-Shift Light” under Manual Transmission Operation on page 2-22 for more information. United States Canada This light should come on brieﬂy when you turn the ignition key to ON. If it does not come on then, have it ﬁxed so it will be ready to warn you if there is a problem. 3-30 When the ignition is on, the brake system warning light will also come on when you set your parking brake. See Parking Brake on page 2-28 for more information. The light will stay on if your parking brake does not release fully. If it stays on after your parking brake is fully released, it means you have a brake problem. If the light comes on while you are driving, pull off the road and stop carefully. You may notice that the pedal is harder to push, or the pedal may go closer to the ﬂoor. It may take longer to stop. If the light is still on, have the vehicle towed for service. See Towing Your Vehicle on page 4-50. {CAUTION: Your brake system may not be working properly if the brake system warning light is on. Driving with the brake system warning light on can lead to an accident. If the light is still on after you have pulled off the road and stopped carefully, have the vehicle towed for service. Anti-Lock Brake System Warning Light With the anti-lock brake system, this light will come on brieﬂy when you start your engine to show it is working. Then it will turn off. This is normal. If the light stays on, or comes on when you’re driving, your vehicle needs service. If the regular brake system warning light isn’t on, you still have brakes, but you don’t have anti-lock brakes. If the regular brake system warning light is also on, you don’t have anti-lock brakes and there’s a problem with your regular brakes. See Brake System Warning Light on page 3-30. The anti-lock brake system warning light should come on brieﬂy when you turn the ignition key to ON. If the light doesn’t come on then, have it ﬁxed so it will be ready to warn you if there is a problem. 3-31 Engine Coolant Temperature Gage This gage shows the engine coolant temperature. Malfunction Indicator Lamp Check Engine Light Your vehicle is equipped with a computer which monitors operation of the fuel, ignition, and emission control systems. If the gage pointer is near the top of the gage, the engine is too hot. It means that your engine coolant has overheated. If you have been operating your vehicle under normal driving conditions, you should pull off the road, stop your vehicle and turn off the engine as soon as possible. See Engine Overheating on page 5-28 for more information. This system is called OBD II (On-Board Diagnostics-Second Generation) and is intended to assure that emissions are at acceptable levels for the life of the vehicle, helping to produce a cleaner environment. The check engine light comes on to indicate that there is a problem and service is required. Malfunctions often will be indicated by the system before any problem is apparent. This may prevent more serious damage to your vehicle. This system is also designed to assist your service technician in correctly diagnosing any malfunction. 3-32 If you keep driving your vehicle with this Notice: light on, after awhile, your emission controls may not work as well, your fuel economy may not be as good, and your engine may not run as smoothly. This could lead to costly repairs that may not be covered by your warranty. Notice: Modiﬁcations made to the engine, transmission, exhaust, intake, or fuel system of your vehicle or the replacement of the original tires with other than those of the same Tire Performance Criteria (TPC) can affect your vehicle’s emission controls and may cause this light to come on. Modiﬁcations to these systems could lead to costly repairs not covered by your warranty. This may also result in a failure to pass a required Emission Inspection/Maintenance test. See Accessories and Modiﬁcations on page 5-3. This light should come on, as a check to show you it is working, when the ignition is on and the engine is not running. If the light does not come on, have it repaired. This light will also come on during a malfunction in one of two ways: Light Flashing — A misﬁre condition has been detected. A misﬁre increases vehicle emissions and may damage the emission control system on your vehicle. Diagnosis and service may be required. Light On Steady — An emission control system malfunction has been detected on your vehicle. Diagnosis and service may be required. 3-33 (cid:127) (cid:127) If the Light is Flashing The following may prevent more serious damage to your vehicle: (cid:127) Reducing vehicle speed (cid:127) Avoiding hard accelerations (cid:127) Avoiding steep uphill grades If you are towing a trailer, reduce the amount of cargo being hauled as soon as it is possible If the light stops ﬂashing and remains on steady, see “If the Light Is On Steady” following. If the light continues to ﬂash, when it is safe to do so, stop the vehicle. Find a safe place to park your vehicle. Turn the key off, wait at least 10 seconds and restart the engine. If the light remains on steady, see “If the Light Is On Steady” following. If the light is still ﬂashing, follow the previous steps, and see your dealer for service as soon as possible. If the Light Is On Steady You may be able to correct the emission system malfunction by considering the following: Did you recently put fuel into your vehicle? If so, reinstall the fuel cap, making sure to fully install the cap. See Filling the Tank on page 5-8. The diagnostic system can determine if the fuel cap has been left off or improperly installed. A loose or missing fuel cap will allow fuel to evaporate into the atmosphere. A few driving trips with the cap properly installed should turn the light off. Did you just drive through a deep puddle of water? If so, your electrical system may be wet. The condition will usually be corrected when the electrical system dries out. A few driving trips should turn the light off. 3-34 (cid:127) Have you recently changed brands of fuel? If so, be sure to fuel your vehicle with quality fuel. See Gasoline Octane on page 5-5. Poor fuel quality will cause your engine not to run as efficiently as designed. You may notice this as stalling after start-up, stalling when you put the vehicle into gear, misﬁring, hesitation on acceleration, or stumbling on acceleration. (These conditions may go away once the engine is warmed up.) This will be detected by the system and cause the light to turn on. If you experience one or more of these conditions, change the fuel brand you use. It will require at least one full tank of the proper fuel to turn the light off. If none of the above steps have made the light turn off, your dealer can check the vehicle. Your dealer has the proper test equipment and diagnostic tools to ﬁx any mechanical or electrical problems that may have developed. Emissions Inspection and Maintenance Programs Some state/provincial and local governments have or may begin programs to inspect the emission control equipment on your vehicle. Failure to pass this inspection could prevent you from getting a vehicle registration. Here are some things you need to know to help your vehicle pass an inspection: Your vehicle will not pass this inspection if the check engine light is on or not working properly. Your vehicle will not pass this inspection if the OBD (on-board diagnostic) system determines that critical emission control systems have not been completely diagnosed by the system. The vehicle would be considered not ready for inspection. This can happen if you have recently replaced your battery or if your battery has run down. The diagnostic system is designed to evaluate critical emission control systems during normal driving. This may take several days of routine driving. If you have done this and your vehicle still does not pass the inspection for lack of OBD system readiness, your GM dealer can prepare the vehicle for inspection. 3-35 Oil Pressure Light {CAUTION: Do not keep driving if the oil pressure is low. If you do, your engine can become so hot that it catches ﬁre. You or others could be burned. Check your oil as soon as possible and have your vehicle serviced. Notice: Lack of proper engine oil maintenance may damage the engine. The repairs would not be covered by your warranty. Always follow the maintenance schedule in this manual for changing engine oil. This light tells you if there could be a problem with your engine oil pressure. The light goes on when you turn your key to ON or START. It goes off once you start your engine. That’s a check to be sure the light works. If it doesn’t come on, be sure to have it ﬁxed so it will be there to warn you if something goes wrong. When the light comes on and stays on, it means that oil isn’t ﬂowing through your engine properly. You could be low on oil and you might have some other system problem. See Engine Oil on page 5-13 and “OIL” under DIC Warnings and Messages on page 3-42 for more information. 3-36 Security Light Cruise Control Light This light will come on brieﬂy when you turn the key to START. The light will stay on until the engine starts. This light comes on whenever you set your cruise control. If the ignition is turned on, and the light ﬂashes, the Passlock® system has entered a tamper mode. If the vehicle fails to start, see Passlock® on page 2-15. If the light comes on continuously while driving and stays on, there may be a problem with the Passlock® system. Your vehicle will not be protected by Passlock®, and you should see your dealer. Also, see Content Theft-Deterrent on page 2-13 for additional information regarding the security light. The light will go out when the cruise control is turned off. See Cruise Control on page 3-11 for more information. Highbeam On Light This light comes on whenever the high-beam headlamps are on. See Headlamp High/Low-Beam Changer on page 3-9 for more information. 3-37 Daytime Running Lamps (DRL) Indicator Light This light turns on whenever the Daytime Running Lamps are on. See Daytime Running Lamps (DRL) on page 3-15 for more information. Fuel Gage When the ignition is on, the fuel gage tells you about how much fuel you have remaining in the fuel tank. Here are four things that some owners ask about. None of these indicate a problem with your fuel gage: (cid:127) At the gas station, the gas pump shuts off before the gage reads full. It takes a little more or less fuel to ﬁll up than the gage indicated. For example, the gage may have indicated the tank was half full, but it actually took a little more or less than half the tank’s capacity to ﬁll the tank. The gage moves a little when you turn a corner or speed up. The gage does not go back to empty when you turn off the ignition. When the fuel in the fuel tank is low, you will see a LOW FUEL message on the Driver Information Center (DIC) display. See DIC Warnings and Messages on page 3-42 for more information. 3-38 (cid:127) (cid:127) (cid:127) Trip Information Odometer The odometer is automatically displayed on the DIC when you start the vehicle. The odometer shows the total distance the vehicle has been driven in either miles for the United States or kilometers for Canada. Trip Odometer Press and release the reset stem until TRIP appears on the DIC display. This shows the current distance traveled since the last reset of the trip odometer in either miles for the United States or kilometers for Canada. Press and hold the reset stem for approximately four seconds to reset the trip odometer. Driver Information Center (DIC) The Driver Information Center (DIC) displays information such as the trip odometer, personalization features, and warning messages. The DIC display is located on the instrument panel cluster. DIC Controls and Displays The Driver Information Center (DIC) comes on when the ignition is on. After a short delay, the DIC will display the information that was last displayed before the engine was turned off. If a problem is detected, a warning message will appear on the display. Pressing and releasing the trip odometer reset stem on the DIC will acknowledge some current warnings or service messages. Some messages will only clear after the required action has been taken. The DIC has different modes which can be accessed by pressing the trip odometer reset stem on the DIC. These modes are explained in the following section. The DIC trip odometer reset stem is located on the instrument panel cluster next to the DIC display. To scroll through the available functions, press and release the reset stem. 3-39 Engine Oil Life System Press the reset stem until OIL LIFE RESET appears — alternating between OIL LIFE and RESET — on the DIC display. The engine oil life system calculates an estimate of the oil’s remaining useful life. The CHANGE OIL message will alert you to change your oil on a schedule consistent with your driving conditions. Always reset the OIL LIFE message after an oil change. To reset the message, see Engine Oil Life System on page 5-16. In addition to the engine oil life system monitoring the oil life, additional maintenance is recommended in the Maintenance Schedule in this manual. See Engine Oil on page 5-13 and Scheduled Maintenance on page 6-4 for more information. Language This feature allows you to choose the language in which the DIC display will show information. To set your choice for this feature, perform the following steps: 1. With the engine off, turn the key to ON. 2. Close all doors and make sure that the DOORS message is not displayed in the DIC. 3. Press and release the reset stem until the language is shown on the DIC display. 3-40 4. To view the next available language, press and hold the reset stem for approximately two seconds. Release the reset stem and press and hold again to view each language. You can choose from English (default), Spanish, or French. 5. Once the desired language is shown on the DIC display, brieﬂy press the reset stem to set your choice. Automatic Door Locks This feature allows you to program your door locks to a preferred setting. To set your choice for this feature, perform the following steps: 1. With the engine off, turn the key to LOCK. Do not remove the key from the ignition. 2. Press and hold the power door lock button for approximately three seconds until the DIC display shows the current door lock mode. 3. To view the next available mode, press and hold the reset stem for approximately two seconds. Release the reset stem and press and hold again to view each mode. 4. Once the desired mode is shown on the DIC display, brieﬂy press the reset stem to set your choice. The DIC display will then clear. The following are the available modes: Lock 1 (default): On vehicles with an automatic transmission, this mode locks all of the doors when the vehicle is shifted out of PARK (P) and unlocks all of the doors when the vehicle is shifted into PARK (P). On vehicles with a manual transmission, this mode locks all of the doors when the vehicle speed is greater than 15 mph (24 km/h) and unlocks all of the doors when the key is removed from the ignition. Lock 2: On vehicles with an automatic transmission, this mode locks all of the doors when the vehicle is shifted out of PARK (P) and unlocks the driver’s door when the vehicle is shifted into PARK (P). On vehicles with a manual transmission, this mode locks all of the doors when the vehicle speed is greater than 15 mph (24 km/h) and unlocks the driver’s door when the key is removed from the ignition. Lock 3: On vehicles with an automatic transmission, this mode locks all of the doors when the vehicle is shifted out of PARK (P). The doors will not automatically unlock. On vehicles with a manual transmission, this mode locks all of the doors when the vehicle speed is greater than 15 mph (24 km/h). The doors will not automatically unlock. Remote Keyless Entry Feedback This feature allows you to program your remote keyless entry feedback to a preferred setting. To set your choice for this feature, perform the following steps: 1. With the engine off, turn the key to LOCK. Do not remove the key from the ignition. 2. Press and hold the lock and unlock buttons on the remote keyless entry transmitter at the same time. Hold both buttons until the DIC display shows the current remote keyless entry feedback mode. 3. To view the next available mode, press and hold the reset stem for approximately two seconds. Release the reset stem and press and hold again to view each mode. 4. Once the desired mode is shown on the DIC display, brieﬂy press the reset stem to set your choice. The DIC display will then clear. 3-41 The following are the available modes: RFA 1 (default): This mode ﬂashes the parking lamps when you press the lock or unlock buttons on the remote keyless entry transmitter. RFA 2: This mode ﬂashes the parking lamps and sounds the horn when you press the lock button on the remote keyless entry transmitter. This mode also ﬂashes the parking lamps when you press the unlock button on the remote keyless entry transmitter. RFA 3: This mode ﬂashes the parking lamps and sounds the horn when you press the lock or unlock buttons on the remote keyless entry transmitter. RFA 4: This mode disables remote keyless entry feedback. There will be no feedback when you press the lock or unlock buttons on the remote keyless entry transmitter. DIC Warnings and Messages Warning messages are displayed on the DIC to notify the driver that the status of the vehicle has changed and that some action may be needed by the driver to correct the condition. More than one message may appear at one time. They will appear one after the other. The messages are displayed for three seconds each. Some messages may not require immediate action but you should press and release the trip odometer reset stem to acknowledge that you received the message and clear it from the display. Each message must be acknowledged individually. Some messages cannot be cleared from the display because they are more urgent. These messages require action before they can be removed from the DIC display. The following are the possible messages that can be displayed and some information about them. 3-42 AC (Air Conditioning) OFF This message will be displayed when the engine coolant temperature is too high and the air conditioning in your vehicle needs to be turned off. See Engine Overheating on page 5-28 and Climate Control System on page 3-19 for more information. It will be displayed along with the ENG HOT message. ABS (Anti-Lock Brake System) This message will be displayed if there is a problem with your anti-lock brake system. Check your anti-lock brake system as soon as possible and have your vehicle serviced by your GM dealer. See Brakes on page 5-37 and Anti-Lock Brake System Warning Light on page 3-31 for more information. Press and release the reset stem to acknowledge the message and clear it from the DIC display. BATTERY This message will be displayed when there is a problem with your vehicle’s battery. See Battery on page 5-41 and Battery Warning Light on page 3-29 for more information. BRAKES This message will be displayed if there is a problem with your brakes. Check your brakes as soon as possible and have your vehicle serviced by your GM dealer. See Brakes on page 5-37 and Brake System Warning Light on page 3-30 for more information. Press and release the reset stem to acknowledge the message and clear it from the DIC display. CHANGE OIL This message will be displayed when the oil needs to be changed. Check the oil in your vehicle as soon as possible and have your vehicle serviced by your GM dealer. See Engine Oil on page 5-13 and Scheduled Maintenance on page 6-4 for more information. Press the reset stem to acknowledge the message and clear it from the display. DOORS This message will be displayed on your DIC when one or more of your doors is ajar. You should check all the doors on your vehicle to make sure they are closed. The message will clear from the display after all of the doors are closed. 3-43 LOW FUEL This message will be displayed if the level of fuel in your vehicle is low. You should also check your fuel gage. See Fuel Gage on page 3-38 for more information. You should ﬁll your vehicle’s tank as soon as possible. LOW TRAC (Traction) If you have the Traction Control System (TCS), you will see this message when a low traction condition is detected. See Traction Control System (TCS) on page 4-9 for more information. Press and release the reset stem to acknowledge the message and clear it from the DIC display. OIL This message will be displayed when your oil pressure is low. See Oil Pressure Light on page 3-36 and Engine Oil on page 5-13 for more information. ENG (Engine) HOT This message will be displayed when your engine coolant temperature is hot. Check your engine coolant temperature gage. See Engine Coolant Temperature Gage on page 3-32 for more information. You should have your vehicle serviced by your GM dealer as soon as possible if you suspect your engine is overheating. See Engine Overheating on page 5-28 for more information. FLUID This message will be displayed if your brake ﬂuid is low. Check the brake ﬂuid as soon as possible and have your vehicle serviced by your GM dealer. See Brakes on page 5-37 for more information. Press the reset stem to acknowledge the message and clear it from the DIC display. FUEL CAP This message will be displayed if your vehicle’s fuel cap is either off or loose. You should pull over and check to see if your vehicle’s fuel cap is secure as soon as possible. You may also see the check engine light on the instrument panel cluster. See Malfunction Indicator Lamp on page 3-32 for more information. Press the reset stem to acknowledge the message and clear it from the display. 3-44 PARK BRK (Brake) This message will be displayed when your vehicle’s parking brake is active. See Parking Brake on page 2-28 and Brake System Warning Light on page 3-30 for more information. The message will clear from the display after the parking brake is released. REDUCED POWER This message will be displayed when your vehicle’s engine power is reduced. Press the reset stem to acknowledge the message and clear it from the display. SERV (Service) 4WD (Four-Wheel Drive) This message will be displayed when there is a problem with your transfer case control system. Check the transfer case on your vehicle and have it serviced by your GM dealer. See Four-Wheel Drive on page 2-24 for more information about your transfer case. Press the reset stem to acknowledge the message and clear it from the display. TRACTION FAULT If you have the Traction Control System (TCS), you may see this message if there is a problem with your Traction Control System (TCS). Check your TCS as soon as possible and have your vehicle serviced by your GM dealer. See Traction Control System (TCS) on page 4-9 for more information. Press the reset stem to acknowledge the message and clear it from the display. SERV (Service) VEH (Vehicle) This message will be displayed if your vehicle needs service. You should have your vehicle serviced by your GM dealer as soon as possible. TURN SIGNAL This message will be displayed when your turn signal is on for approximately 0.75 miles (1.2 km) of travel. Press the reset stem to acknowledge the message and clear it from the display. 3-45 Audio System(s) Driving without distraction is a necessity for a safer driving experience. See Defensive Driving on page 4-2. By taking a few moments to read this manual and get familiar with your vehicle’s audio system, you can use it with less effort, as well as take advantage of its features. While your vehicle is parked, set up your audio system by presetting your favorite radio stations, setting the tone and adjusting the speakers. Then, when driving conditions permit, you can tune to your favorite stations using the presets and steering wheel controls (if equipped). {CAUTION: This system provides you with a far greater access to audio stations and song listings. Giving extended attention to entertainment tasks while driving can cause a crash and you or others can be injured or killed. Always keep your eyes on the road and your mind on the drive — avoid engaging in extended searching while driving. Keeping your mind on the drive is important for safe driving. For more information, see Defensive Driving on page 4-2. Get familiar with your vehicle’s audio system so you can use it with less effort and take full advantage of its features. 3-46 Here are some ways in which you can help avoid distraction while driving. While your vehicle is parked: Familiarize yourself with all of its controls. Familiarize yourself with its operation. (cid:127) Set up your audio system by presetting your favorite radio stations, setting the tone, and adjusting the speakers. Then, when driving conditions permit, you can tune to your favorite radio stations using the presets and steering wheel controls (if equipped). Notice: Before adding any sound equipment to your vehicle, such as an audio system, CD player, CB radio, mobile telephone, or two-way radio, make sure that it can be added by checking with your dealer. Also, check federal rules covering mobile radio and telephone units. If sound equipment can be added, it is very important to do it properly. Added sound equipment may interfere with the operation of your vehicle’s engine, radio, or other systems, and even damage them. Your vehicle’s systems may interfere with the operation of sound equipment that has been added. Notice: The chime signals related to seat belts, parking brake, and other functions of your vehicle operate through the GM radio/entertainment system. If that equipment is replaced or additional equipment is added to your vehicle, the chimes may not work. Make sure that replacement or additional equipment is compatible with your vehicle before installing it. See Accessories and Modiﬁcations on page 5-3. Figure out which audio system is in your vehicle, ﬁnd out what your audio system can do, and how to operate all of its controls. Setting the Time for Radios without Radio Data Systems (RDS) Press and hold HR until the correct hour appears on the display. Press and hold MIN until the correct minute appears on the display. There is an initial two-second delay before the clock goes into time-set mode. Display the time with the ignition off, by pressing RCL, HR, or MIN. 3-47 (cid:127) (cid:127) Setting the Time for Radios with Radio Data Systems (RDS) The radio may have a button marked with an H or HR to represent hours and an M or MN to represent minutes. Press and hold the hour button until the correct hour appears on the display. Press and hold the minute button until the correct minute appears on the display. The time can be set with the ignition on or off. To synchronize the time with an FM station broadcasting Radio Data System (RDS) information, press and hold the hour and minute buttons at the same time until RDS TIME appears on the display. To accept this time, press and hold the hour and minute buttons, at the same time, for another two seconds. If the time is not available from the station, NO UPDAT will appear on the display. RDS time is broadcast once a minute. After tuning to an RDS broadcast station, it may take a few minutes for the time to update. 3-48 AM-FM Radio Playing the Radio PWR (Power): Press this knob to turn the system on and off. VOL (Volume): Turn this knob to increase or to decrease the volume. RCL (Recall): Press this knob to switch the display between the radio station frequency, band, and the time. When the ignition is off, press this knob to display the time. Finding a Station AM FM: Press this button to switch between FM1, FM2, or AM. The display will show the selection. TUNE: Turn this knob to select radio stations. o SEEK p: Press the right or the left arrow to go to the next or to the previous station and stay there. To scan stations, press and hold either SEEK arrow for two seconds until you hear a beep. The radio will go to a station, play for a few seconds, then go on to the next station. Press either SEEK arrow again to stop scanning. To scan preset stations, press and hold either SEEK arrow for more than four seconds until you hear two beeps. The radio will go to the ﬁrst preset station stored on the pushbuttons, play for a few seconds, then go on to the next preset station. Press either SEEK arrow again to stop scanning presets. The radio will only seek and scan stations with a strong signal that are in the selected band. Setting Preset Stations Up to 18 stations (six FM1, six FM2, and six AM) can be programmed on the six numbered pushbuttons, by performing the following steps:

Boost Classifieds - Car Advice, Reviews, Events & Classifieds

2006 GMC Canyon Owners Manual