Download PDF Manual

1–800–665–2006.


277


2009 Taurus X (219) Owners Guide, 2nd Printing USA (fus)


Roadside Emergencies


HAZARD FLASHER CONTROL The hazard flasher control is located on the instrument panel by the radio. The hazard flashers will operate when the ignition is in any position or if the key is not in the ignition. Push in the flasher control and all front and rear direction signals will flash. Press the flasher control again to turn them off. Use it when your vehicle is disabled and is creating a safety hazard for other motorists. Note: With extended use, the flasher may run down your battery.


FUEL PUMP SHUT-OFF SWITCH This device stops the electric fuel pump from sending fuel to the engine when your vehicle has had a substantial jolt. After an accident, if the engine cranks but does not start, this switch may have been activated. The fuel pump shut-off switch is located in the front passenger footwell area in the right upper corner. To reset the switch: 1. Turn the ignition to the off position. 2. Check the fuel system for leaks. 3. If no leaks are apparent, reset the switch by pushing in on the reset button. 4. Turn the ignition the on position. 5. Wait a few seconds and return the key to the off position. 6. Make another check for leaks.


278


2009 Taurus X (219) Owners Guide, 2nd Printing USA (fus)


Roadside Emergencies


FUSES AND RELAYS


Fuses If electrical components in the vehicle are not working, a fuse may have blown. Blown fuses are identified by a broken wire within the fuse. Check the appropriate fuses before replacing any electrical components. Note: Always replace a fuse with one that has the specified amperage rating. Using a fuse with a higher amperage rating can cause severe wire damage and could start a fire. Standard fuse amperage rating and color


15


COLOR


Mini fuses


Grey Violet Pink Tan


Brown


Red Blue Yellow Natural Green


— — — — —


Standard


fuses


Grey Violet Pink Tan


Brown


Red Blue Yellow Natural Green


— — — — —


Maxi fuses


— — — — — — —


Yellow



Green Orange


Red Blue Tan


Natural


Cartridge


maxi fuses


— — — — — — — Blue — Pink Green Red Yellow



Black


Fuse rating


2A 3A 4A 5A 7.5A 10A 15A 20A 25A 30A 40A 50A 60A 70A 80A


Fuse link cartridge


— — — — — — — Blue — Pink Green Red Yellow Brown Black


279


2009 Taurus X (219) Owners Guide, 2nd Printing USA (fus)


Roadside Emergencies


Passenger compartment fuse panel


The fuse panel is located under the instrument panel to the left of the steering wheel. The fuses are coded as follows.


Fuse/Relay Location


Fuse Amp


Rating


Protected Circuits


280


30A 15A


15A


30A 10A 20A 10A


Smart window motor Brake on/off switch, High-mounted brake lamp SDARS, Bluetooth, Family entertainment system (FES)/Rear seat control Not used (spare) SPDJB logic power Turn signals Low beam headlamps (left)


2009 Taurus X (219) Owners Guide, 2nd Printing USA (fus)


Roadside Emergencies


Fuse/Relay Location


Fuse Amp


Rating


Protected Circuits


10
11
12


13
14
15
16
17


18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35


10A 15A 15A 10A 7.5A


5A 10A 10A 15A 20A


20A 25A 15A 15A 15A 15A 20A 10A 10A 20A 5A 5A 5A 10A 10A 10A 5A 10A


Low beam headlamps (right) Interior lights, Cargo lamps Backlighting, Puddle lamps All wheel drive Memory seat/mirror switches, Memory module FEPS module Power liftgate module Climate control Not used (spare) All power lock motor feeds, Liftgate release 2nd row power seat Moon roof OBDII connector Fog lamps Park lamps, License lamps High beam headlamps Horn relay Demand lamps/Interior lamps Instrument panel cluster Adjustable pedal switch Radio, Radio start signal Instrument panel cluster Overdrive cancel switch Not used (spare) Not used (spare) Restraint control module AWD module Steering rotation sensor, FEPS, Rear park assist, Heated seat modules


281


2009 Taurus X (219) Owners Guide, 2nd Printing USA (fus)


Roadside Emergencies


Fuse/Relay Location


Fuse Amp


Rating


Protected Circuits


36
37
38
39
40
41


42
43
44
45


46


47


48


5A 10A 20A 20A 20A 15A


10A 10A 10A 5A


7.5A


30A Circuit


Breaker


PATS module Climate control Subwoofer (Audiophile radio) Radio Spare Moon roof, Front lock switches, Radio, EC Mirror with compass (with and without microphone) Not used (spare) Not used (spare) Not used (spare) Relay coils: PDB, Auxiliary A/C, Front and rear wipers, Front blower motor Occupant Classification Sensor (OCS), Passenger Airbag Deactivation Indicator (PADI) Power windows



Delayed accessory relay


Power distribution box The power distribution box is located in the engine compartment. The power distribution box contains high-current fuses that protect your vehicle’s main electrical systems from overloads.


WARNING: Always disconnect the battery before servicing high current fuses.


WARNING: To reduce risk of electrical shock, always replace the cover to the Power Distribution Box before reconnecting the


battery or refilling fluid reservoirs.


If the battery has been disconnected and reconnected, refer to the Battery section of the Maintenance and Specifications chapter.


282


2009 Taurus X (219) Owners Guide, 2nd Printing USA (fus)


Roadside Emergencies


The high-current fuses are coded as follows:


Fuse/Relay Location


10
11


12
13
14
15


Fuse Amp


Protected Circuits


Rating 80A* 80A* 30A*



20A*



50A*



40A*


30A* 50A*


20A* 20A** 20A** 20A**


SPDJB power SPDJB power Front wipers Not used Rear heated seat module Not used Engine cooling fan Not used Anti-lock Brake System (ABS)/AdvanceTrac pump Starter Powertrain Control Module (PCM) relay ABS/AdvanceTrac valve Power point (instrument panel) Power point (2nd row) Power point (3rd row)


283


2009 Taurus X (219) Owners Guide, 2nd Printing USA (fus)


Roadside Emergencies


Fuse/Relay Location


16
17
18
19
20
21
22
23


24
25
26
27


28
29
30
31
32


33
34
35
36
37
38
39
40
41
42
43


Fuse Amp


Protected Circuits


Rating 20A** 10A**


— —


40A* 30A* 20A* 10A**


10A** 25A** 20A** 15A**



30A*



30A* 30A*


20A*



40A*


1A Diode 1A Diode


10A** 10A** 10A**


G8VA relay G8VA relay G8VA relay


Power point (console) Alternator Not used Not used Rear defroster Power seat motors (passenger) Heated seat module PCM Keep alive power, Canister vent A/C clutch relay Rear wiper Backup relay Fuel relay (Fuel pump driver module, Fuel pump) Not used Power liftgate Not used Auxiliary blower relay Driver seat motors, Memory module Ignition switch (to SJB) Not used Front A/C blower motor One-touch start Fuel pump IVD, Yaw rate sensor Fuel diode, PCM Auxiliary coolant pump A/C clutch Fuel pump Backup


284


2009 Taurus X (219) Owners Guide, 2nd Printing USA (fus)


Roadside Emergencies


Protected Circuits


Rear wiper Speed control deactivate switch, Mass air flow sensor, Inline module VPWR2
A/C clutch relay, VPWR3
PCM VPWR1
PCM VPWR4
Heated mirrors PCM relay Not used Not used Rear defrost relay Blower motor relay Starter relay Not used Front wiper relay Not used


Fuse Amp


Rating


G8VA relay


10A**


10A** 15A** 15A** 15A**


Full ISO relay


— —


Full ISO relay Full ISO relay Full ISO relay



Full ISO relay



Fuse/Relay Location


44
45


46
47
48
49
50
51
52
53
54
55
56
57
58


* Cartridge Fuses ** Mini Fuses


CHANGING THE TIRES If you get a flat tire while driving: • do not brake heavily. • gradually decrease the vehicle’s speed. • hold the steering wheel firmly. • slowly move to a safe place on the side of the road. Note: The tire pressure monitoring system (TPMS) indicator light will illuminate when the spare is in use. To restore the full functionality of the monitoring system, all road wheels equipped with tire pressure monitoring sensors must be mounted on the vehicle. Have a flat serviced by an authorized dealer in order to prevent damage to the TPMS sensor, refer to Changing tires with TPMS in the Tires, Wheels and Loading chapter. Replace the spare tire with a road tire as soon as possible.


285


2009 Taurus X (219) Owners Guide, 2nd Printing USA (fus)


Roadside Emergencies


WARNING: The use of tire sealants may damage your Tire Pressure Monitoring System and should not be used.


WARNING: Refer to Tire Pressure Monitoring System (TPMS) in the Tires, Wheels and Loading chapter for important


information. If the tire pressure monitor sensor becomes damaged, it will no longer function.


Dissimilar spare tire/wheel information


WARNING: Failure to follow these guidelines could result in an increased risk of loss of vehicle control, injury or death.


If you have a dissimilar spare tire/wheel, then it is intended for temporary use only. This means that if you need to use it, you should replace it as soon as possible with a road tire/wheel that is the same size and type as the road tires and wheels that were originally provided by Ford. If the dissimilar spare tire or wheel is damaged, it should be replaced rather than repaired. A dissimilar spare tire/wheel is defined as a spare tire and/or wheel that is different in brand, size or appearance from the road tires and wheels and can be one of three types: 1. T-type mini-spare: This spare tire begins with the letter “T” for tire size and may have “Temporary Use Only” molded in the sidewall 2. Full-size dissimilar spare with label on wheel: This spare tire has a label on the wheel that states: “THIS TIRE AND WHEEL FOR TEMPORARY USE ONLY” When driving with one of the dissimilar spare tires listed above, do not: • Exceed 50 mph (80 km/h) • Load the vehicle beyond maximum vehicle load rating listed on the • Tow a trailer • Use snow chains on the end of the vehicle with the dissimilar spare • Use more than one dissimilar spare tire at a time • Use commercial car washing equipment • Try to repair the dissimilar spare tire


Safety Compliance Label


tire


286


2009 Taurus X (219) Owners Guide, 2nd Printing USA (fus)


Roadside Emergencies


Use of one of the dissimilar spare tires listed above at any one wheel location can lead to impairment of the following: • Handling, stability and braking performance • Comfort and noise • Ground clearance and parking at curbs • Winter weather driving capability • Wet weather driving capability 3. Full-size dissimilar spare without label on wheel When driving with the full-size dissimilar spare tire/wheel, do not: • Exceed 70 mph (113 km/h) • Use more than one dissimilar spare tire/wheel at a time • Use commercial car washing equipment • Use snow chains on the end of the vehicle with the dissimilar spare


tire/wheel


The usage of a full-size dissimilar spare tire/wheel can lead to impairment of the following: • Handling, stability and braking performance • Comfort and noise • Ground clearance and parking at curbs • Winter weather driving capability • Wet weather driving capability • All-Wheel driving capability (if applicable) • Load leveling adjustment (if applicable) When driving with the full-size dissimilar spare tire/wheel additional caution should be given to: • Towing a trailer • Driving vehicles equipped with a camper body • Driving vehicles with a load on the cargo rack Drive cautiously when using a full-size dissimilar spare tire/wheel and seek service as soon as possible.


287


2009 Taurus X (219) Owners Guide, 2nd Printing USA (fus)


Roadside Emergencies


Stopping and securing the vehicle 1. Park on a level surface, set the parking brake and activate hazard flashers. 2. Place gearshift lever in P (Park) and turn engine off.


Removing the spare tire and jack If the 3rd row seat (if equipped) is stowed in the floor, you will need to unstow it to access the spare tire and jack. Refer to Unstowing the third row seat in the Seating and Safety Restraint chapter for this procedure. 1. Remove the carpeted floor panel located in the rear of the vehicle, remove the wing nut that secures the spare tire by turning it counterclockwise. 2. Lift and remove the spare tire from the trunk. 3. Remove the second wing nut that secures the jack retention bracket by turning it counterclockwise, remove the jack kit from the vehicle. 4. Remove the jack and the wrench from the felt bag. Fold down the wrench socket to use to loosen the lug nuts and to operate the jack.


288


2009 Taurus X (219) Owners Guide, 2nd Printing USA (fus)


Roadside Emergencies


Tire change procedure


WARNING: When one of the front wheels is off the ground, the transmission alone will not prevent the vehicle from moving or


slipping off the jack, even if the vehicle is in P (Park).


WARNING: To help prevent the vehicle from moving when you change a tire, be sure to place the transmission in P (Park), set


the parking brake and block (in both directions) the wheel that is diagonally opposite (other side and end of the vehicle) to the tire being changed.


WARNING: If the vehicle slips off the jack, you or someone else could be seriously injured.


WARNING: Do not attempt to change a tire on the side of the vehicle close to moving traffic. Pull far enough off the road to


avoid the danger of being hit when operating the jack or changing the wheel.


1. Block the diagonally opposite wheel.


2. Remove wheel cover (if equipped) with the lug wrench tip and loosen each wheel lug nut one-half turn counterclockwise but do not remove them until the wheel is raised off the ground.


2009 Taurus X (219) Owners Guide, 2nd Printing USA (fus)


289


Roadside Emergencies


WARNING: To lessen the risk of personal injury, do not put any part of your body under the vehicle while changing a tire. Do not


start the engine when your vehicle is on the jack. The jack is only meant for changing the tire.


3. Put the jack in the jack notch next to the tire you are changing. Turn the jack handle clockwise until the wheel is completely off the ground.


4. Remove the lug nuts with the lug wrench. 5. Replace the flat tire with the spare tire, making sure the valve stem is facing outward. Reinstall the lug nuts until the wheel is snug against the hub. Do not fully tighten the lug nuts until the wheel has been lowered. 6. Lower the wheel by turning the jack handle counterclockwise. 7. Remove the jack and fully tighten the lug nuts in the order shown. Refer to Wheel lug nut torque specifications later in this chapter for the proper lug nut torque specification. 8. Install the wheel cover (if equipped). The wheel cover will only install if the Ford/Mercury logo is aligned over the valve stem on the wheel.


290


2009 Taurus X (219) Owners Guide, 2nd Printing USA (fus)


Roadside Emergencies


Stowing the tire and jack 1. Fully collapse the jack, fold the lug wrench socket into the handle and place the jack and wrench into the felt bag as shown. Take care to position the jack as shown to ensure that the locating holes in the jack base can be placed on the locating tabs of the jack mounting bracket in the spare tire tub. 2. Securely close the wrench compartment and the jack bag using the VELCRO威 strips. 3. Place the jack kit on the angled bracket in the spare tire tub, using the locating tabs to position the jack correctly. 4. Insert the straight end of the jack retention bracket through the eyelet of the angled bracket and swing the retention bracket over the jack. With the jack in place, place the end of the retention bracket over the threaded stud in the trunk floor and secure it with the plastic wing nut.


291


2009 Taurus X (219) Owners Guide, 2nd Printing USA (fus)


Roadside Emergencies


If you are stowing the flat tire, remove the “L”-shaped bolt from the large wing nut used to secure the spare tire in the vehicle. With the 3rd row seat in the raised position, stand the flat tire in the rear of the vehicle with the tire’s valve stem facing the rear of the vehicle. Fasten the flat tire to the vehicle by inserting the “L”-shaped bolt through one of the lug bolt holes in the wheel and turning clockwise into the threaded hole in the vehicle until the tire is secured. If you are stowing the temporary spare tire, place the tire over the jack and secure it with the large wing nut.


WHEEL LUG NUT TORQUE SPECIFICATIONS Retighten the lug nuts to the specified torque at 100 miles (160 km) after any wheel disturbance (tire rotation, changing a flat tire, wheel removal, etc.).


Bolt size


Wheel lug nut torque*


1/2-20 UNF * Torque specifications are for nut and bolt threads free of dirt and rust. Use only Ford recommended replacement fasteners.


lb.ft. 100


N•m 135


WARNING: When a wheel is installed, always remove any corrosion, dirt or foreign materials present on the mounting


surfaces of the wheel or the surface of the wheel hub, brake drum or brake disc that contacts the wheel. Ensure that any fasteners that attach the rotor to the hub are secured so they do not interfere with the mounting surfaces of the wheel. Installing wheels without correct metal-to-metal contact at the wheel mounting surfaces can cause the wheel nuts to loosen and the wheel to come off while the vehicle is in motion, resulting in loss of control.


292


2009 Taurus X (219) Owners Guide, 2nd Printing USA (fus)


Roadside Emergencies


Note: Inspect the wheel pilot hole prior to installation. If there is visible corrosion in wheel pilot hole, remove loose particles by wiping with clean rag and apply grease. Apply grease only to the wheel pilot hole surface by smearing a “dime” (1 square cm) sized glob of grease around the wheel pilot surface (1) with end of finger. DO NOT apply grease to lugnut/stud holes or wheel-to-brake surfaces.


JUMP STARTING


WARNING: The gases around the battery can explode if exposed to flames, sparks, or lit cigarettes. An explosion could


result in injury or vehicle damage.


WARNING: Batteries contain sulfuric acid which can burn skin, eyes and clothing, if contacted.


Do not attempt to push-start your automatic transmission vehicle. Automatic transmissions do not have push-start capability. Attempting to push-start a vehicle with an automatic transmission may cause transmission damage.


Preparing your vehicle When the battery is disconnected or a new battery is installed, the automatic transmission must relearn its shift strategy. As a result, the transmission may have firm and/or soft shifts. This operation is considered normal and will not affect function or durability of the transmission. Over time, the adaptive learning process will fully update transmission operation. 1. Use only a 12–volt supply to start your vehicle. 2. Do not disconnect the battery of the disabled vehicle as this could damage the vehicle’s electrical system. 3. Park the booster vehicle close to the hood of the disabled vehicle making sure the two vehicles do not touch. Set the parking brake on both vehicles and stay clear of the engine cooling fan and other moving parts.


293


2009 Taurus X (219) Owners Guide, 2nd Printing USA (fus)


Roadside Emergencies


4. Check all battery terminals and remove any excessive corrosion before you attach the battery cables. Ensure that vent caps are tight and level. 5. Turn the heater fan on in both vehicles to protect from any electrical surges. Turn all other accessories off.


Connecting the jumper cables


+–


+–


1. Connect the positive (+) jumper cable to the positive (+) terminal of the discharged battery. Note: In the illustrations, lightning bolts are used to designate the assisting (boosting) battery.


+–


+–


2. Connect the other end of the positive (+) cable to the positive (+) terminal of the assisting battery.


294


2009 Taurus X (219) Owners Guide, 2nd Printing USA (fus)


Roadside Emergencies


+–


+–


3. Connect the negative (-) cable to the negative (-) terminal of the assisting battery.


+–


+–


4. Make the final connection of the negative (-) cable to an exposed metal part of the stalled vehicle’s engine, away from the battery and the carburetor/fuel injection system. Do not use fuel lines, engine rocker covers or the intake manifold as grounding points.


WARNING: Do not connect the end of the second cable to the negative (-) terminal of the battery to be jumped. A spark may


cause an explosion of the gases that surround the battery.


5. Ensure that the cables are clear of fan blades, belts, moving parts of both engines, or any fuel delivery system parts.


295


2009 Taurus X (219) Owners Guide, 2nd Printing USA (fus)


Roadside Emergencies


Jump starting 1. Start the engine of the booster vehicle and run the engine at moderately increased speed. 2. Start the engine of the disabled vehicle. 3. Once the disabled vehicle has been started, run both engines for an additional three minutes before disconnecting the jumper cables.


Removing the jumper cables


+–


+–


Remove the jumper cables in the reverse order that they were connected. 1. Remove the jumper cable from the ground metal surface. Note: In the illustrations, lightning bolts are used to designate the assisting (boosting) battery.


+–


+–


2. Remove the jumper cable on the negative (-) connection of the booster vehicle’s battery.


296


2009 Taurus X (219) Owners Guide, 2nd Printing USA (fus)


Roadside Emergencies


+–


+–


3. Remove the jumper cable from the positive (+) terminal of the booster vehicle’s battery.


+–


+–


4. Remove the jumper cable from the positive (+) terminal of the disabled vehicle’s battery. After the disabled vehicle has been started and the jumper cables removed, allow it to idle for several minutes so the engine computer can relearn its idle conditions.


297


2009 Taurus X (219) Owners Guide, 2nd Printing USA (fus)


Roadside Emergencies


WRECKER TOWING


If you need to have your vehicle towed, contact a professional towing service or, if you are a member of a roadside assistance program, your roadside assistance service provider. It is recommended that your vehicle be towed with a wheel lift and dollies or flatbed equipment. Do not tow with a slingbelt. Ford Motor Company has not approved a slingbelt towing procedure. On FWD vehicles, if your vehicle is to be towed from the front, ensure proper wheel lift equipment is used to raise the front wheels off the ground. The rear wheels can be left on the ground when towed in this fashion. If your vehicle is to be towed from the rear using wheel lift equipment, it is recommended that the front wheels (drive wheels) be placed on a dolly to prevent damage to the automatic transmission. On AWD vehicles, it is required that your vehicle be towed with a wheel lift and dollies or flatbed equipment with all the wheels off the ground to prevent damage to the automatic transmission, AWD system or vehicle.


298


2009 Taurus X (219) Owners Guide, 2nd Printing USA (fus)


Roadside Emergencies


If the vehicle is towed by other means or incorrectly, vehicle damage may occur. Ford Motor Company produces a towing manual for all authorized tow truck operators. Have your tow truck operator refer to this manual for proper hook-up and towing procedures for your vehicle.


Emergency towing In case of a roadside emergency with a disabled vehicle (without access to wheel dollies, car hauling trailer, or flatbed transport vehicle) your vehicle (regardless of transmission powertrain configuration) can be flat towed (all wheels on the ground) under the following conditions: • Vehicle is facing forward so that it is being towed in a forward • Place the transmission in N (Neutral). Refer to Brake shift interlock in the Driving chapter for specific instructions if you cannot move the gear shift lever into N (Neutral).


direction.


• Maximum speed is not to exceed 35 mph (56 km/h). • Maximum distance is 50 miles (80 km).


299


2009 Taurus X (219) Owners Guide, 2nd Printing USA (fus)


Customer Assistance


GETTING THE SERVICES YOU NEED Warranty repairs to your vehicle must be performed by an authorized Ford, Lincoln, or Mercury dealer. While any authorized dealer handling your vehicle line will provide warranty service, we recommend you return to your selling authorized dealer who wants to ensure your continued satisfaction. Please note that certain warranty repairs require special training and/or equipment, so not all authorized dealers are authorized to perform all warranty repairs. This means that, depending on the warranty repair needed, you may have to take your vehicle to another authorized dealer. A reasonable time must be allowed to perform a repair after taking your vehicle to the authorized dealer. Repairs will be made using Ford or Motorcraft parts, or remanufactured or other parts that are authorized by Ford.


Away from home If you are away from home when your vehicle needs service, contact the Ford Customer Relationship Center or use the online resources listed below to find the nearest authorized dealer. In the United States: Mailing Address Ford Motor Company Customer Relationship Center P.O. Box 6248
Dearborn, MI 48121
Telephone 1-800-392-3673 (FORD) (TDD for the hearing impaired: 1-800-232-5952) Online Additional information and resources are available online at www.genuineservice.com. • U.S. dealer locator by Dealer Name, City/State, or Zip Code • Owner Guides • Maintenance Schedules • Recalls • Ford Extended Service Plans • Ford Genuine Accessories • Service specials and promotions. 300


2009 Taurus X (219) Owners Guide, 2nd Printing USA (fus)


Customer Assistance


In Canada: Mailing Address (Ford vehicles) Customer Relationship Centre Ford Motor Company of Canada, Limited P.O. Box 2000
Oakville, Ontario L6J 5E4
Telephone 1-800-565-3673 (FORD) Online www.ford.ca Mailing Address (Lincoln vehicles) Lincoln Centre Ford Motor Company of Canada, Limited P.O. Box 2000
Oakville, Ontario L6J 5E4
Telephone 1-800-387-9333
Online www.lincolncanada.com Additional Assistance If you have questions or concerns, or are unsatisfied with the service you are receiving, follow these steps: 1. Contact your Sales Representative or Service Advisor at your selling/servicing authorized dealer. 2. If your inquiry or concern remains unresolved, contact the Sales Manager, Service Manager or Customer Relations Manager. 3. If you require assistance or clarification on Ford Motor Company policies, please contact the Ford Customer Relationship Center In order to help you serve you better, please have the following information available when contacting a Customer Relationship Center: • Vehicle Identification Number (VIN) • Your telephone number (home and business) • The name of the authorized dealer and city where located • The vehicle’s current odometer reading In some states, you must directly notify Ford in writing before pursuing remedies under your state’s warranty laws. Ford is also allowed a final repair attempt in some states.


301


2009 Taurus X (219) Owners Guide, 2nd Printing USA (fus)


Customer Assistance


In the United States, a warranty dispute must be submitted to the BBB AUTO LINE before taking action under the Magnuson-Moss Warranty Act, or to the extent allowed by state law, before pursuing replacement or repurchase remedies provided by certain state laws. This dispute handling procedure is not required prior to enforcing state created rights or other rights which are independent of the Magnuson-Moss Warranty Act or state replacement or repurchase laws.


IN CALIFORNIA (U.S. ONLY) California Civil Code Section 1793.2(d) requires that, if a manufacturer or its representative is unable to repair a motor vehicle to conform to the vehicle’s applicable express warranty after a reasonable number of attempts, the manufacturer shall be required to either replace the vehicle with one substantially identical or repurchase the vehicle and reimburse the buyer in an amount equal to the actual price paid or payable by the consumer (less a reasonable allowance for consumer use). The consumer has the right to choose whether to receive a refund or replacement vehicle. California Civil Code Section 1793.22(b) presumes that the manufacturer has had a reasonable number of attempts to conform the vehicle to its applicable express warranties if, within the first 18 months of ownership of a new vehicle or the first 18,000 miles (29,000 km), whichever occurs first: 1. Two or more repair attempts are made on the same non-conformity likely to cause death or serious bodily injury OR 2. Four or more repair attempts are made on the same nonconformity (a defect or condition that substantially impairs the use, value or safety of the vehicle) OR 3. The vehicle is out of service for repair of nonconformities for a total of more than 30 calendar days (not necessarily all at one time) In the case of 1 or 2 above, the consumer must also notify the manufacturer of the need for the repair of the nonconformity at the following address: Ford Motor Company 16800 Executive Plaza Drive Mail Drop 3NE-B Dearborn, MI 48126


THE BETTER BUSINESS BUREAU (BBB) AUTO LINE PROGRAM (U.S. ONLY) Your satisfaction is important to Ford Motor Company and to your dealer. If a warranty concern has not been resolved using the three-step


302


2009 Taurus X (219) Owners Guide, 2nd Printing USA (fus)


Customer Assistance


procedure outlined on the first page of the Customer Assistance section, you may be eligible to participate in the BBB AUTO LINE program. The BBB AUTO LINE program consists of two parts – mediation and arbitration. During mediation, a representative of the BBB will contact both you and Ford Motor Company to explore options for settlement of the claim. If an agreement is not reached during mediation and your claim is eligible, you may participate in the arbitration process. An arbitration hearing will be scheduled so that you can present your case in an informal setting before an impartial person. The arbitrator will consider the testimony provided and make a decision after the hearing. You are not bound by the decision, but should you choose to accept the BBB AUTO LINE decision, Ford must abide by the accepted decision as well. Disputes submitted to the BBB AUTO LINE program are usually decided within forty days after you file your claim with the BBB. BBB AUTO LINE Application: Using the information provided below, please call or write to request a program application. You will be asked for your name and address, general information about your new vehicle, information about your warranty concerns, and any steps you have already taken to try to resolve them. A Customer Claim Form will be mailed that will need to be completed, signed and returned to the BBB along with proof of ownership. Upon receipt, the BBB will review the claim for eligibility under the Program Summary Guidelines. You can get more information by calling BBB AUTO LINE at 1-800-955-5100, or writing to: BBB AUTO LINE 4200 Wilson Boulevard, Suite 800
Arlington, Virginia 22203–1833
BBB AUTO LINE applications can also be requested by calling the Ford Motor Company Customer Relationship Center at 1-800-392-3673. Note: Ford Motor Company reserves the right to change eligibility limitations, modify procedures, or to discontinue this process at any time without notice and without obligation.


UTILIZING THE MEDIATION/ARBITRATION PROGRAM (CANADA ONLY) For vehicles delivered to authorized Canadian dealers. In those cases where you continue to feel that the efforts by Ford of Canada and the authorized dealer to resolve a factory-related vehicle service concern have been unsatisfactory, Ford of Canada participates in an impartial third party mediation/arbitration program administered by the Canadian Motor Vehicle Arbitration Plan (CAMVAP).


303


2009 Taurus X (219) Owners Guide, 2nd Printing USA (fus)


Customer Assistance


The CAMVAP program is a straight-forward and relatively speedy alternative to resolve a disagreement when all other efforts to produce a settlement have failed. This procedure is without cost to you and is designed to eliminate the need for lengthy and expensive legal proceedings. In the CAMVAP program, impartial third-party arbitrators conduct hearings at mutually convenient times and places in an informal environment. These impartial arbitrators review the positions of the parties, make decisions and, when appropriate, render awards to resolve disputes. CAMVAP decisions are fast, fair, and final as the arbitrator’s award is binding both to you and Ford of Canada. CAMVAP services are available in all territories and provinces. For more information, without charge or obligation, call your CAMVAP Provincial Administrator directly at 1-800-207-0685.


FORD EXTENDED SERVICE PLAN You can get more protection for your new car or light truck by purchasing Ford Extended Service Plan (Ford ESP) coverage. It provides the following: • Benefits during the warranty period depending on the plan you


purchase (such as: reimbursement for rentals; coverage for certain maintenance and wear items).


• Protection against covered repair costs after your Bumper-to-Bumper


Warranty expires.


You may purchase Ford ESP from any participating authorized dealer. There are several plans available in various time, distance and deductible combinations which can be tailored to fit your own driving needs. Ford ESP also offers reimbursement benefits for towing and rental coverage. When you buy Ford ESP, you receive Peace-of-Mind protection throughout the United States and Canada, provided by a network of more than 4,600 participating authorized dealers. If you did not take advantage of the Ford Extended Service Plan at the time of purchasing your vehicle, you may still be eligible. Since this information is subject to change, please ask your authorized dealer for complete details about Ford Extended Service Plan coverage options, or visit the Ford ESP website at www.ford-esp.com.


GETTING ASSISTANCE OUTSIDE THE U.S. AND CANADA Before exporting your vehicle to a foreign country, contact the appropriate foreign embassy or consulate. These officials can inform you of local vehicle registration regulations and where to find unleaded fuel.


304


2009 Taurus X (219) Owners Guide, 2nd Printing USA (fus)


Customer Assistance


If you cannot find unleaded fuel or can only get fuel with an anti-knock index lower than is recommended for your vehicle, contact a regional office or owner relations/customer relationship office. The use of leaded fuel in your vehicle without proper conversion may damage the effectiveness of your emission control system and may cause engine knocking or serious engine damage. Ford Motor Company/Ford of Canada is not responsible for any damage caused by use of improper fuel. Using leaded fuel may also result in difficulty importing your vehicle back into the U.S. If your vehicle must be serviced while you are traveling or living in Central America, the Caribbean, or the Middle East, contact the nearest authorized dealer. If the authorized dealer cannot help you, contact: FORD MOTOR COMPANY FORD EXPORT OPERATIONS 1555 Fairlane Drive Fairlane Business Park #3
Allen Park, Michigan 48101
U.S.A. Telephone: (313) 594-4857
FAX: (313) 390-0804
Email: [email protected] If you are in another foreign country, contact the nearest authorized dealer. If the authorized dealer employees cannot help you, they can direct you to the nearest Ford affiliate office. If you buy your vehicle in North America and then relocate outside of the U.S. or Canada, register your vehicle identification number (VIN) and new address with Ford Motor Company Export Operations. Customers in the U.S. should call 1-800-392-3673.


ORDERING ADDITIONAL OWNER’S LITERATURE To order the publications in this portfolio, contact Helm, Incorporated at: HELM, INCORPORATED P.O. Box 07150
Detroit, Michigan 48207
Or to order a free publication catalog, call toll free: 1-800-782-4356
Monday-Friday 8:00 a.m. - 6:00 p.m. EST Helm, Incorporated can also be reached by their website: www.helminc.com. (Items in this catalog may be purchased by credit card, check or money order.)


305


2009 Taurus X (219) Owners Guide, 2nd Printing USA (fus)


Customer Assistance


Obtaining a French owner’s guide French Owner’s Guides can be obtained from your authorized dealer or by writing to: Ford Motor Company of Canada, Limited Service Publications CHQ202
The Canadian Road P.O. Box 2000
Oakville, ON, Canada L6J 5E4


REPORTING SAFETY DEFECTS (U.S. ONLY) If you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying Ford Motor Company. If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign. However, NHTSA cannot become involved in individual problems between you, your dealer, or Ford Motor Company. To contact NHTSA, you may call the Vehicle Safety Hotline toll-free at 1–888–327–4236 (TTY: 1–800–424–9153); go to http://www.safercar.gov; or write to: Administrator 1200 New Jersey Avenue, Southeast Washington, D.C. 20590
You can also obtain other information about motor vehicle safety from http://www.safercar.gov.


REPORTING SAFETY DEFECTS (CANADA ONLY) If you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immediately inform Transport Canada, using their toll-free number: 1–800–333–0510.


306


2009 Taurus X (219) Owners Guide, 2nd Printing USA (fus)


Cleaning


WASHING THE EXTERIOR Wash your vehicle regularly with cool or lukewarm water and a neutral pH shampoo, such as Motorcraft Detail Wash (ZC-3-A), which is available from your authorized dealer. • Never use strong household detergents or soap, such as dish washing


strong, direct sunlight.


or laundry liquid. These products can discolor and spot painted surfaces.


• Never wash a vehicle that is “hot to the touch” or during exposure to • Always use a clean sponge or car wash mitt with plenty of water for • Dry the vehicle with a chamois or soft terry cloth towel in order to • It is especially important to wash the vehicle regularly during the


eliminate water spotting.


best results.


winter months, as dirt and road salt are difficult to remove and cause damage to the vehicle. • Immediately remove items such as gasoline, diesel fuel, bird droppings


and insect deposits because they can cause damage to the vehicle’s paintwork and trim over time. Use Motorcraft Bug and Tar Remover (ZC-42) which is available from your authorized dealer. • Remove any exterior accessories, such as antennas, before entering a • Suntan lotions and insect repellents can damage any painted surface; if these substances come in contact with your vehicle, wash off as soon as possible.


car wash.


shampoo, such as Motorcraft Detail Wash (ZC-3-A).


Exterior chrome • Wash the vehicle first, using cool or lukewarm water and a neutral pH • Use Motorcraft Custom Bright Metal Cleaner (ZC-15), available from your authorized dealer. Apply the product as you would a wax to clean bumpers and other chrome parts; allow the cleaner to dry for a few minutes, then wipe off the haze with a clean, dry rag. • Never use abrasive materials such as steel wool or plastic pads • After polishing chrome bumpers, apply a coating of Motorcraft


as they can scratch the chrome surface.


Premium Liquid Wax (ZC-53-A), available from your authorized dealer, or an equivalent quality product to help protect from environmental effects.


307


2009 Taurus X (219) Owners Guide, 2nd Printing USA (fus)


Cleaning


WAXING • Wash the vehicle first. • Do not use waxes that contain abrasives; use Motorcraft Premium


Liquid Wax (ZC-53-A), which is available from your authorized dealer, or an equivalent quality product.


• Do not allow paint sealant to come in contact with any non-body (low-gloss black) colored trim, such as grained door handles, roof racks, bumpers, side moldings, mirror housings or the windshield cowl area. The paint sealant will “gray” or stain the parts over time.


spots, road salt and industrial fallout before repairing paint chips.


PAINT CHIPS Your authorized dealer has touch-up paint to match your vehicle’s color. Take your color code (printed on a sticker in the driver’s door jamb) to your authorized dealer to ensure you get the correct color. • Remove particles such as bird droppings, tree sap, insect deposits, tar • Always read the instructions before using the products. ALUMINUM WHEELS AND WHEEL COVERS Aluminum wheels and wheel covers are coated with a clearcoat paint finish. In order to maintain their shine: • Clean weekly with Motorcraft Wheel and Tire Cleaner (ZC-37-A),


covers.


which is available from your authorized dealer. Heavy dirt and brake dust accumulation may require agitation with a sponge. Rinse thoroughly with a strong stream of water.


• Never apply any cleaning chemical to hot or warm wheel rims or • Some automatic car washes may cause damage to the finish on your wheel rims or covers. Chemical-strength cleaners, or cleaning chemicals, in combination with brush agitation to remove brake dust and dirt, could wear away the clearcoat finish over time.


• Do not use hydrofluoric acid-based or high caustic-based wheel • To remove tar and grease, use Motorcraft Bug and Tar Remover


cleaners, steel wool, fuels or strong household detergent.


(ZC-42), available from your authorized dealer.


308


2009 Taurus X (219) Owners Guide, 2nd Printing USA (fus)


Cleaning


ENGINE Engines are more efficient when they are clean because grease and dirt buildup keep the engine warmer than normal. When washing: • Take care when using a power washer to clean the engine. The high-pressure fluid could penetrate the sealed parts and cause damage. • Do not spray a hot engine with cold water to avoid cracking the • Spray Motorcraft Engine Shampoo and Degreaser (ZC-20) on all parts


engine block or other engine components.


that require cleaning and pressure rinse clean. In Canada use Motorcraft Engine Shampoo (CXC-66-A).


• Cover the highlighted areas to prevent water damage when cleaning • Never wash or rinse the engine while it is running; water in the


the engine.


running engine may cause internal damage.


3.5L V6 ENGINE


309


2009 Taurus X (219) Owners Guide, 2nd Printing USA (fus)


Cleaning


PLASTIC (NON-PAINTED) EXTERIOR PARTS Use only approved products to clean plastic parts. These products are available from your authorized dealer. • For routine cleaning, use Motorcraft Detail Wash (ZC-3-A). • If tar or grease spots are present, use Motorcraft Bug and Tar • For plastic headlamp lenses, use Motorcraft Ultra Clear Spray Glass


Remover (ZC-42).


Cleaner (ZC-23).


WINDOWS AND WIPER BLADES The windshield, rear and side windows and the wiper blades should be cleaned regularly. If the wipers do not wipe properly, substances on the vehicle’s glass or the wiper blades may be the cause. These may include hot wax treatments used by commercial car washes, water repellent coatings, tree sap, or other organic contamination; these contaminants may cause squeaking or chatter noise from the blades, and streaking and smearing of the windshield. To clean these items, follow these tips: • The windshield, rear windows and side windows may be cleaned with


a non-abrasive cleaner such as Motorcraft Ultra-Clear Spray Glass Cleaner (ZC-23), available from your authorized dealer.


• The wiper blades can be cleaned with isopropyl (rubbing) alcohol or


Motorcraft Premium Windshield Washer Concentrate (ZC-32-A), available from your authorized dealer. This washer fluid contains special solution in addition to alcohol which helps to remove the hot wax deposited on the wiper blade and windshield from automated car wash facilities. Be sure to replace wiper blades when they appear worn or do not function properly.


• Do not use abrasives, as they may cause scratches. • Do not use fuel, kerosene, or paint thinner to clean any parts. If you cannot remove those streaks after cleaning with the glass cleaner or if the wipers chatter and move in a jerky motion, clean the outer surface of the windshield and the wiper blades using a sponge or soft cloth with a neutral detergent or mild-abrasive cleaning solution. After cleaning, rinse the windshield and wiper blades with clean water. The windshield is clean if beads do not form when you rinse the windshield with water. Do not use sharp objects, such as a razor blade, to clean the inside of the rear window or to remove decals, as it may cause damage to the rear window defroster’s heated grid lines.


310


2009 Taurus X (219) Owners Guide, 2nd Printing USA (fus)


Cleaning


INSTRUMENT PANEL/INTERIOR TRIM AND CLUSTER LENS Clean the instrument panel, interior trim areas and cluster lens with a clean and damp white cotton cloth, then with a clean and dry white cotton cloth; you may also use Motorcraft Dash & Vinyl Cleaner (ZC-38-A) on the instrument panel and interior trim areas. • Avoid cleaners or polishes that increase the gloss of the upper portion of the instrument panel. The dull finish in this area helps protect the driver from undesirable windshield reflection.


• Be certain to wash or wipe your hands clean if you have been in contact with certain products such as insect repellent and suntan lotion in order to avoid possible damage to the interior painted surfaces. • Do not use household or glass cleaners as these may damage the


finish of the instrument panel, interior trim and cluster lens.


WARNING: Do not use chemical solvents or strong detergents when cleaning the steering wheel or instrument panel to avoid


contamination of the airbag system.


If a staining liquid like coffee/juice has been spilled on the instrument panel or on interior trim surfaces, clean as follows: 1. Wipe up spilled liquid using a clean, white, cotton cloth. 2. Apply Motorcraft Deluxe Leather and Vinyl Cleaner (ZC-11-A) [In Canada use Motorcraft Multi-Purpose Cleaner (CXC-101)] to the wiped area and spread around evenly. 3. Apply more Motorcraft cleaner to a clean, white, cotton cloth and press the cloth onto the soiled area–allow this to set at room temperature for 30 minutes. 4. Remove the soaked cloth, and if it is not soiled badly, use this cloth to clean the area by using a rubbing motion for 60 seconds. 5. Following this, wipe area dry with a clean, white, cotton cloth.


INTERIOR For fabric, carpets, cloth seats, safety belts and seats equipped with side airbags: • Remove dust and loose dirt with a vacuum cleaner. • Remove light stains and soil with Motorcraft Professional Strength


Carpet & Upholstery Cleaner (ZC-54).


311


2009 Taurus X (219) Owners Guide, 2nd Printing USA (fus)


Cleaning • If grease or tar is present on the material, spot-clean the area first with Motorcraft Spot and Stain Remover (ZC-14). In Canada, use Motorcraft Multi-Purpose Cleaner (CXC-101).


immediately (but do not oversaturate) or the ring will set.


• If a ring forms on the fabric after spot cleaning, clean the entire area • Do not use household cleaning products or glass cleaners, which can stain and discolor the fabric and affect the flame retardant abilities of the seat materials.


WARNING: Do not use cleaning solvents, bleach or dye on the vehicle’s safety belts, as these actions may weaken the belt


webbing.


WARNING: On vehicles equipped with seat-mounted airbags, do not use chemical solvents or strong detergents. Such products could contaminate the side-airbag system and affect performance of the side airbag in a collision.


LEATHER SEATS (IF EQUIPPED) Your leather seating surfaces have a clear, protective coating over the leather. • For routine cleaning, wipe the surface with a soft, damp cloth. For more thorough cleaning, wipe the surface with a mild soap and water solution. In Canada, use Motorcraft Vinyl Cleaner (CXC-93). Dry the area with a soft cloth.


• If the leather cannot be completely cleaned using a mild soap and water solution, the leather may be cleaned using a commercially available cleaning product designed for automotive leather.


• Do not use household cleaning products, alcohol solutions, solvents or cleaners intended for rubber, vinyl and plastics, or oil/petroleum-based leather conditioners. These products may cause premature wearing of the clear, protective coating.


Note: In some instances, color or dye transfer can occur when wet clothing comes in contact with leather upholstery. If this occurs, the leather should be cleaned immediately to avoid permanent staining.


UNDERBODY Flush the complete underside of your vehicle frequently. Keep body and door drain holes free from packed dirt.


312


2009 Taurus X (219) Owners Guide, 2nd Printing USA (fus)


Cleaning


FORD AND LINCOLN MERCURY CAR CARE PRODUCTS Your Ford or Lincoln Mercury authorized dealer has many quality products available to clean your vehicle and protect its finishes. These quality products have been specifically engineered to fulfill your automotive needs; they are custom designed to complement the style and appearance of your vehicle. Each product is made from high quality materials that meet or exceed rigid specifications. For best results, use the following products or products of equivalent quality: Motorcraft Bug and Tar Remover (ZC-42) Motorcraft Car Wash (Canada only) (CXC-83) Motorcraft Custom Bright Metal Cleaner (ZC-15) Motorcraft Custom Clear Coat Polish (ZC-8-A) Motorcraft Custom Vinyl Protectant (ZC-40-A) Motorcraft Dash and Vinyl Cleaner (ZC-38-A) Motorcraft Deluxe Leather and Vinyl Cleaner (U.S. only) (ZC-11-A) Motorcraft Leather Care Kit (U.S. only) (ZC-11-D) Motorcraft Detail Wash (ZC-3-A) Motorcraft Dusting Cloth (ZC-24) Motorcraft Engine Shampoo and Degreaser (U.S. only) (ZC-20) Motorcraft Engine Shampoo (Canada only) (CXC-66-A) Motorcraft Multi-Purpose Cleaner (Canada only) (CXC-101) Motorcraft Premium Glass Cleaner (Canada only) (CXC-100) Motorcraft Premium Liquid Wax (ZC-53-A) Motorcraft Premium Windshield Washer Concentrate (U.S. only) (ZC-32-A) Motorcraft Professional Strength Carpet & Upholstery Cleaner (ZC-54) Motorcraft Spot and Stain Remover (U.S. only) (ZC-14) Motorcraft Tire Clean and Shine (ZC-28) Motorcraft Triple Clean (U.S. only) (ZC-13) Motorcraft Ultra-Clear Spray Glass Cleaner (ZC-23) Motorcraft Vinyl Cleaner (Canada only) (CXC-93) Motorcraft Wash and Wax (Canada only) (CXC-95) Motorcraft Wheel and Tire Cleaner (ZC-37-A)


313


2009 Taurus X (219) Owners Guide, 2nd Printing USA (fus)


Maintenance and Specifications


SERVICE RECOMMENDATIONS To help you service your vehicle, we provide scheduled maintenance information which makes tracking routine service easy. If your vehicle requires professional service, your authorized dealer can provide the necessary parts and service. Check your Warranty Guide/Customer Information Guide to find out which parts and services are covered. Use only recommended fuels, lubricants, fluids and service parts conforming to specifications. Motorcraft parts are designed and built to provide the best performance in your vehicle.


PRECAUTIONS WHEN SERVICING YOUR VEHICLE • Do not work on a hot engine. • Make sure that nothing gets caught in moving parts. • Do not work on a vehicle with the engine running in an enclosed • Keep all open flames and other burning (cigarettes) material away


space, unless you are sure you have enough ventilation.


from the battery and all fuel related parts.


Working with the engine off 1. Set the parking brake and shift to P (Park). 2. Turn off the engine and remove the key. 3. Block the wheels.


Working with the engine on 1. Set the parking brake and shift to P (Park). 2. Block the wheels.


WARNING: To reduce the risk of vehicle damage and/or personal burn injuries, do not start your engine with the air cleaner removed and do not remove it while the engine is running.


314


2009 Taurus X (219) Owners Guide, 2nd Printing USA (fus)


Maintenance and Specifications


OPENING THE HOOD 1. Inside the vehicle, pull the hood release handle located under the bottom of the instrument panel near the steering column.


2. Go to the front of the vehicle and release the auxiliary latch that is located under the front center of the hood.


3. Lift the hood open and secure it with the prop rod.


315


2009 Taurus X (219) Owners Guide, 2nd Printing USA (fus)


Maintenance and Specifications


IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT


3.5L V6 ENGINE


1. Power steering fluid reservoir 2. Engine coolant reservoir 3. Brake fluid reservoir 4. Battery 5. Power distribution box 6. Air filter assembly 7. Automatic transmission fluid dipstick 8. Engine oil dipstick 9. Engine oil filler cap 10. Windshield washer fluid reservoir


316


2009 Taurus X (219) Owners Guide, 2nd Printing USA (fus)


Maintenance and Specifications


WINDSHIELD WASHER FLUID Add fluid to fill the reservoir if the level is low. In very cold weather, do not fill the reservoir completely. Only use a washer fluid that meets Ford specification WSB-M8B16-A2. Do not use any special washer fluid such as windshield water repellent type fluid or bug wash. They may cause squeaking, chatter noise, streaking and smearing. Refer to the Maintenance product specifications and capacities section in this chapter. State or local regulations on volatile organic compounds may restrict the use of methanol, a common windshield washer antifreeze additive. Washer fluids containing non-methanol antifreeze agents should be used only if they provide cold weather protection without damaging the vehicle’s paint finish, wiper blades or washer system.


WARNING: If you operate your vehicle in temperatures below 40°F (5°C), use washer fluid with antifreeze protection. Failure


to use washer fluid with antifreeze protection in cold weather could result in impaired windshield vision and increase the risk of injury or accident.


Note: Do not put washer fluid in the engine coolant reservoir. Washer fluid placed in the cooling system may harm engine and cooling system components.


317


2009 Taurus X (219) Owners Guide, 2nd Printing USA (fus)


Maintenance and Specifications


CHANGING THE WIPER BLADES 1. Pull the wiper blade and arm away from the glass. 2. Squeeze the locking tabs to release the blade from the arm and pull the blade away from the arm to remove it.


3. Attach the new blade to the arm and snap it into place. Replace wiper blades at least once per year for optimum performance. Poor wiper quality can be improved by cleaning the wiper blades and the windshield. Refer to Windows and wiper blades in the Cleaning chapter. To prolong the life of the wiper blades, it is highly recommended to scrape off the ice on the windshield before turning on the wipers. The layer of ice has many sharp edges and can damage the micro edge of the wiper rubber element.


Changing rear window wiper blade The rear wiper arm is designed without a service position. This reduces the risk of damage to the blade in an automatic car wash.


318


2009 Taurus X (219) Owners Guide, 2nd Printing USA (fus)


Maintenance and Specifications


To replace the wiper blade: 1. Lift and hold the wiper blade off the glass. 2. Press the release tab to unlock wiper blade from wiper arm. 3. Pull the wiper blade toward the base of the wiper arm and remove it from the arm. 4. Attach the new wiper to the wiper arm and press it into place until a click is heard.


ENGINE OIL


Checking the engine oil Refer to the scheduled maintenance information for the appropriate intervals for checking the engine oil. 1. Make sure the vehicle is on level ground. 2. Turn the engine off and wait 15 minutes for the oil to drain into the oil pan. 3. Set the parking brake and ensure the gearshift is securely latched in P (Park). 4. Open the hood. Protect yourself from engine heat. 5. Locate and carefully remove the engine oil level dipstick.


6. Wipe the dipstick clean. Insert the dipstick fully, then remove it again.


319


2009 Taurus X (219) Owners Guide, 2nd Printing USA (fus)


Maintenance and Specifications • If the oil level is within this


range, the oil level is acceptable. DO NOT ADD OIL.


• If the oil level is below this mark, engine oil must be added to raise the level within the normal operating range.


• If required, add engine oil to the engine. Refer to Adding engine oil in this chapter.


• Do not overfill the engine


with oil. Oil levels above this mark may cause engine damage. If the engine is overfilled, some oil must be removed from the engine by an authorized dealer.


7. Put the dipstick back in and ensure it is fully seated.


Adding engine oil 1. Check the engine oil. For instructions, refer to Checking the engine oil in this chapter. 2. If the engine oil level is not within the normal operating range, add only certified engine oil of the recommended viscosity. Remove the engine oil filler cap and use a funnel to pour the engine oil into the opening. 3. Recheck the engine oil level. Make sure the oil level is not above the normal operating range on the engine oil level dipstick.


320


2009 Taurus X (219) Owners Guide, 2nd Printing USA (fus)


Maintenance and Specifications


4. Install the dipstick and ensure it is fully seated. 5. Fully install the engine oil filler cap by turning the filler cap clockwise until it stops. To avoid possible oil loss, DO NOT operate the vehicle with the engine oil level dipstick and/or the engine oil filler cap removed.


Engine oil and filter recommendations Look for this certification trademark.


Use SAE 5W-20 engine oil Only use oils “Certified For Gasoline Engines” by the American Petroleum Institute (API). An oil with this trademark symbol conforms to the current engine and emission system protection standards and fuel economy requirements of the International Lubricant Standardization and Approval Committee (ILSAC), comprised of U.S. and Japanese automobile manufacturers. To protect your engine and engine’s warranty, use Motorcraft SAE 5W-20
or an equivalent SAE 5W-20 oil meeting Ford specification WSS-M2C930-A. SAE 5W-20 oil provides optimum fuel economy and durability performance meeting all requirements for your vehicle’s engine. Refer to Maintenance product specifications and capacities later in this section for more information. Do not use supplemental engine oil additives, cleaners or other engine treatments. They are unnecessary and could lead to engine damage that is not covered by Ford warranty. Change your engine oil and filter according to the appropriate schedule listed in the scheduled maintenance information. Ford production and Motorcraft replacement oil filters are designed for added engine protection and long life. If a replacement oil filter is used that does not meet Ford material and design specifications, start-up engine noises or knock may be experienced.


321


2009 Taurus X (219) Owners Guide, 2nd Printing USA (fus)


Maintenance and Specifications


It is recommended you use the appropriate Motorcraft oil filter or another with equivalent performance for your engine application. BATTERY Your vehicle is equipped with a Motorcraft maintenance-free battery which normally does not require additional water during its life of service.


If your battery has a cover/shield, make sure it is reinstalled after the battery has been cleaned or replaced. For longer, trouble-free operation, keep the top of the battery clean and dry. Also, make certain the battery cables are always tightly fastened to the battery terminals. If you see any corrosion on the battery or terminals, remove the cables from the terminals and clean with a wire brush. You can neutralize the acid with a solution of baking soda and water. It is recommended that the negative battery cable terminal be disconnected from the battery if you plan to store your vehicle for an extended period of time. This will minimize the discharge of your battery during storage. Note: Electrical or electronic accessories or components added to the vehicle by the dealer or the owner may adversely affect battery performance and durability.


WARNING: Batteries normally produce explosive gases which can cause personal injury. Therefore, do not allow flames, sparks or lighted substances to come near the battery. When working near the battery, always shield your face and protect your eyes. Always provide proper ventilation.


WARNING: When lifting a plastic-cased battery, excessive pressure on the end walls could cause acid to flow through the vent caps, resulting in personal injury and/or damage to the vehicle or battery. Lift the battery with a battery carrier or with your hands on opposite corners.


322


2009 Taurus X (219) Owners Guide, 2nd Printing USA (fus)


Maintenance and Specifications


WARNING: Keep batteries out of reach of children. Batteries contain sulfuric acid. Avoid contact with skin, eyes or clothing.


Shield your eyes when working near the battery to protect against possible splashing of acid solution. In case of acid contact with skin or eyes, flush immediately with water for a minimum of 15 minutes and get prompt medical attention. If acid is swallowed, call a physician immediately.


WARNING: Battery posts, terminals and related accessories contain lead and lead compounds. Wash hands after handling.


Because your vehicle’s engine is electronically controlled by a computer, some control conditions are maintained by power from the battery. When the battery is disconnected or a new battery is installed, the engine must relearn its idle and fuel trim strategy for optimum driveability and performance. To begin this process: 1. With the vehicle at a complete stop, set the parking brake. 2. Put the gearshift in P (Park), turn off all accessories and start the engine. 3. Run the engine until it reaches normal operating temperature. 4. Allow the engine to idle for at least one minute. 5. Turn the A/C on and allow the engine to idle for at least one minute. 6. Release the parking brake. With your foot on the brake pedal and with the A/C on, put the vehicle in D (Drive) and allow the engine to idle for at least one minute. 7. Drive the vehicle to complete the relearning process. • The vehicle may need to be driven 10 miles (16 km) or more to • If you do not allow the engine to relearn its idle trim, the idle quality of your vehicle may be adversely affected until the idle trim is eventually relearned.


relearn the idle and fuel trim strategy.


If the battery has been disconnected or a new battery has been installed, the clock and radio settings must be reset once the battery is reconnected.


323


2009 Taurus X (219) Owners Guide, 2nd Printing USA (fus)


Maintenance and Specifications • Always dispose of automotive batteries in a responsible manner. Follow your local authorized standards for disposal. Call your local authorized recycling center to find out more about recycling automotive batteries.


RECYCLE


ENGINE COOLANT


Checking engine coolant The concentration and level of engine coolant should be checked at the intervals listed in scheduled maintenance information. The coolant concentration should be maintained at 50/50 coolant and distilled water, which equates to a freeze point of -34°F (-36°C). Coolant concentration testing is possible with a hydrometer or antifreeze tester. The level of coolant should be maintained at the “FULL COLD” level or within the “COLD FILL RANGE” in the coolant reservoir. If the level falls below, add coolant per the instructions in the Adding engine coolant section. Your vehicle was factory-filled with a 50/50 engine coolant and water concentration. If the concentration of coolant falls below 40% or above 60%, the engine parts could become damaged or not work properly. A 50/50 mixture of coolant and water provides the following: • Freeze protection down to -34°F (-36°C). • Boiling protection up to 265°F (129°C). • Protection against rust and other forms of corrosion. • Proper function of calibrated gauges.


324


2009 Taurus X (219) Owners Guide, 2nd Printing USA (fus)


Maintenance and Specifications


When the engine is cold, check the level of the engine coolant in the reservoir.


• The engine coolant should be at the “FULL COLD” level or within the


“COLD FILL RANGE” as listed on the engine coolant reservoir (depending upon application).


• Refer to scheduled maintenance information for service interval • Be sure to read and understand Precautions when servicing your


schedules.


vehicle in this chapter.


If the engine coolant has not been checked at the recommended interval, the engine coolant reservoir may become low or empty. If the reservoir is low or empty, add engine coolant to the reservoir. Refer to Adding engine coolant in this chapter. Note: Automotive fluids are not interchangeable; do not use engine coolant, antifreeze or windshield washer fluid outside of its specified function and vehicle location.


Adding engine coolant When adding coolant, make sure it is a 50/50 mixture of engine coolant and distilled water. Add the mixture to the coolant reservoir, when the engine is cool, until the appropriate fill level is obtained.


WARNING: Do not add engine coolant when the engine is hot. Steam and scalding liquids released from a hot cooling system


can burn you badly. Also, you can be burned if you spill coolant on hot engine parts.


WARNING: Do not put engine coolant in the windshield washer fluid container. If sprayed on the windshield, engine coolant


could make it difficult to see through the windshield.


325


2009 Taurus X (219) Owners Guide, 2nd Printing USA (fus)


Maintenance and Specifications • Add Motorcraft Premium Gold Engine Coolant or equivalent


meeting Ford specification WSS-M97B51-A1. Refer to Maintenance product specifications and capacities in this chapter. Note: Do not use stop leak pellets or cooling system sealants/additives as they can cause damage to the engine cooling and/or heating systems. This damage would not be covered under your vehicle’s warranty. • Do not add/mix an orange-colored, extended life coolant such as Motorcraft Specialty Orange Engine Coolant, meeting Ford specification WSS-M97B44-D, or DEX-COOL威 brand with the factory-filled coolant. Mixing Motorcraft Specialty Orange Engine Coolant or any orange-colored extended life product such as DEX-COOL威 brand with your factory filled coolant can result in degraded corrosion protection.


• A large amount of water without engine coolant may be added, in case of emergency, to reach a vehicle service location. In this instance, the cooling system must be drained and refilled with a 50/50 mixture of engine coolant and distilled water as soon as possible. Water alone (without engine coolant) can cause engine damage from corrosion, overheating or freezing. • Do not use alcohol, methanol, brine or any engine coolants mixed with alcohol or methanol antifreeze (coolant). Alcohol and other liquids can cause engine damage from overheating or freezing.


• Do not add extra inhibitors or additives to the coolant. These


can be harmful and compromise the corrosion protection of the engine coolant.


For vehicles with overflow coolant systems with a non-pressurized cap on the coolant recovery system, add coolant to the coolant recovery reservoir when the engine is cool. Add the proper mixture of coolant and water to the “FULL COLD” level. For all other vehicles which have a coolant degas system with a pressurized cap, or if it is necessary to remove the coolant pressure relief cap on the radiator of a vehicle with an overflow system, follow these steps to add engine coolant.


WARNING: To reduce the risk of personal injury, make sure the engine is cool before unscrewing the coolant pressure relief cap. The cooling system is under pressure; steam and hot liquid can come out forcefully when the cap is loosened slightly.


326


2009 Taurus X (219) Owners Guide, 2nd Printing USA (fus)


Maintenance and Specifications


Add the proper mixture of coolant and water to the cooling system by following these steps: 1. Before you begin, turn the engine off and let it cool. 2. When the engine is cool, wrap a thick cloth around the coolant pressure relief cap on the coolant reservoir (a translucent plastic bottle). Slowly turn cap counterclockwise (left) until pressure begins to release. 3. Step back while the pressure releases. 4. When you are sure that all the pressure has been released, use the cloth to turn it counterclockwise and remove the cap. 5. Fill the coolant reservoir slowly with the proper coolant mixture, to within the “COLD FILL RANGE” or the “FULL COLD” level on the reservoir. If you removed the radiator cap in an overflow system, fill the radiator until the coolant is visible and radiator is almost full.

Loading...
x