Login- Download PDF Manual
-
• During the first 500 miles (805 km) your new vehicle is driven, do not tow a trailer. Doing so may damage your vehicle. • Limit your speed to 50 mph (80 km/h) during the
first 500 miles (805 km) of towing.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 71
SAFETY TIPS
Transporting Passengers This vehicle is designed to carry passengers in the cab only. For safety reasons, NEVER TRANSPORT PASSEN- GERS IN THE CARGO AREA.
WARNING!
It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts. Be sure everyone in your vehicle is in a seat and using a seat belt properly.
72 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
Lock Your Vehicle Always remove the keys from the ignition and lock all doors when leaving the vehicle unattended, even in your own driveway or garage. Try to park your vehicle in a well-lighted area and never invite theft by leaving ar- ticles of value exposed. Exhaust Gas
WARNING!
Exhaust gases contain carbon monoxide, a poten- tially toxic gas that by itself is colorless and odorless. To avoid inhaling these gases, the following precau- tions should be observed: • Do not run the engine in a closed garage or in confined areas any longer than needed to move your vehicle in or out of the area.
• If it is necessary to sit in a parked vehicle with the engine running for more than a short period, adjust your climate control system to force outside air into the vehicle. Set the blower at high speed and the controls in any position except OFF or MAX A/C. • The best protection against carbon monoxide entry into the vehicle body is a properly maintained engine exhaust system.
Be aware of changes in the sound of the exhaust system; exhaust fumes detected inside the vehicle; or damage to the underside or rear of the vehicle. Have a competent mechanic inspect the complete exhaust system and adja- cent body areas for broken, damaged, deteriorated or mispositioned parts. Open seams or loose connections could permit exhaust fumes to seep into the passenger compartment. In addition, inspect the exhaust system each time the vehicle is raised for lubrication or oil change. Replace or adjust as required.
Safety Checks You Should Make Inside The Vehicle
Seat Belts Inspect the belt system periodically, checking for cuts, frays and loose parts. Damaged parts must be replaced immediately. Do not disassemble or modify the system. Seat belt assemblies must be replaced after an accident if they have been damaged (bent retractor, torn webbing, etc.) or if the front airbags have deployed. If there is any question regarding belt or retractor condition, replace the belt.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 73
Airbag Light The light should come on and remain on for 6 to 8
seconds as a bulb check when the ignition switch is first turned ON. If the light is not lit during starting, see you authorized dealer. If the light stays on, flickers or comes on while driving, have the system checked by an autho- rized dealer. If there is a problem with the airbag light the seatbelt light will flash.74 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
Safety Checks You Should Make Outside The Vehicle
Tires Examine tires for tread wear or uneven wear patterns. Check for stones, nails, glass or other objects lodged in the tread. Inspect for tread cuts or sidewall cracks. Check wheel nuts for tightness and tires for proper pressure. Lights Check the operation of all exterior lights. Check turn signal and high beam indicator lights on the instrument panel.
Door Latches Check for positive closing, latching and locking. Fluid Leaks Check area under vehicle after overnight parking for fuel, water, oil, or other fluid leaks. Also, if fuel fumes are detected the cause should be located and corrected.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE
CONTENTS
䡵 Power Wagon Features . . . . . . . . . . . . . . . . . . . .80
▫ Locking Front And Rear Differentials . . . . . . . .80
▫ 4.56:1 Gears . . . . . . . . . . . . . . . . . . . . . . . . . .80
▫ Electronically Disconnecting Stabilizer/SwayBar
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .81
▫ Increased Ride Height . . . . . . . . . . . . . . . . . . .81
▫ 12,000 Lb. Winch . . . . . . . . . . . . . . . . . . . . . . .81
▫ High-Pressure Monotube Shocks/New FrontAnd Rear Springs . . . . . . . . . . . . . . . . . . . . . .82
. . . . . . . . . . . . . . . . . . . . . . . .82▫ Off-Road Tires
▫ Skid Plates And Underbody Protection . . . . . . .82
▫ Wheel Flares . . . . . . . . . . . . . . . . . . . . . . . . . .82
▫ Wheels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .83
▫ Standard Package Features . . . . . . . . . . . . . . . .83
▫ Mopar Options . . . . . . . . . . . . . . . . . . . . . . . .84
䡵 Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .84
▫ Inside Mirror . . . . . . . . . . . . . . . . . . . . . . . . .84
▫ Automatic Dimming Mirror— If Equipped . . . .85
▫ Outside Mirrors . . . . . . . . . . . . . . . . . . . . . . .8676 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
▫ Exterior Mirrors Folding Feature . . . . . . . . . . .86
▫ Electronic Power Mirrors — If Equipped . . . . . .87
▫ Electric Rear Window Defroster And HeatedSideview Mirrors — If Equipped . . . . . . . . . . .88
▫ Trailer Towing Mirrors — If Equipped . . . . . . .88䡵 Hands–Free Communication (UConnect™)
— If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . .90
▫ Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . .91
▫ Phone Call Features . . . . . . . . . . . . . . . . . . . .95
▫ Advanced Phone Connectivity . . . . . . . . . . . . .97
▫ UConnect™ System Features . . . . . . . . . . . . . .99
䡵 Seats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102
▫ 40-20-40 Front Seat . . . . . . . . . . . . . . . . . . . . 102
▫ Reclining Seats . . . . . . . . . . . . . . . . . . . . . . . 103▫ Adjustable Head Restraints . . . . . . . . . . . . . . 104
▫ Manual Rotary Lumbar Support Adjustment— If Equipped . . . . . . . . . . . . . . . . . . . . . . . 105
▫ Power Seats — If Equipped . . . . . . . . . . . . . . 105
▫ Heated Seats — If Equipped . . . . . . . . . . . . . 107
䡵 To Open And Close The Hood . . . . . . . . . . . . . 108
䡵 Lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109
▫ Interior Lights . . . . . . . . . . . . . . . . . . . . . . . 110
▫ Battery Saver . . . . . . . . . . . . . . . . . . . . . . . . 111
▫ Headlamp Delay — If Equipped . . . . . . . . . . 111
▫ Headlights, Parking Lights, Panel Lights . . . . . 111
▫ Daytime Running Lights (Canada And FleetVehicles Only)
. . . . . . . . . . . . . . . . . . . . . . . 112
▫ Lights-On Reminder . . . . . . . . . . . . . . . . . . . 113▫ Fog Lights — If Equipped . . . . . . . . . . . . . . . 113
▫ Cargo Light . . . . . . . . . . . . . . . . . . . . . . . . . 113
䡵 Multifunction Control Lever . . . . . . . . . . . . . . . 113
▫ Turn Signals . . . . . . . . . . . . . . . . . . . . . . . . . 113
▫ Passing Light . . . . . . . . . . . . . . . . . . . . . . . . 114
▫ High Beam / Low Beam Select Switch . . . . . . 115
▫ Windshield Wipers . . . . . . . . . . . . . . . . . . . . 115
▫ Windshield Washers . . . . . . . . . . . . . . . . . . . 117
䡵 Tilt Steering Column . . . . . . . . . . . . . . . . . . . . 117
䡵 Electronic Speed Control — If Equipped . . . . . . 118
▫ To Activate . . . . . . . . . . . . . . . . . . . . . . . . . . 118
▫ To Set At A Desired Speed . . . . . . . . . . . . . . . 119
▫ To Deactivate . . . . . . . . . . . . . . . . . . . . . . . . 119UNDERSTANDING THE FEATURES OF YOUR VEHICLE 77
▫ To Resume Speed . . . . . . . . . . . . . . . . . . . . . 119
▫ To Vary The Speed Setting . . . . . . . . . . . . . . . 120
▫ To Accelerate For Passing . . . . . . . . . . . . . . . 121
䡵 Overhead Console— If Equipped . . . . . . . . . . . 122
▫ Courtesy/Reading Lights . . . . . . . . . . . . . . . . 122䡵 Overhead Console With Compass/Temperature
Mini-Trip Computer — If Equipped . . . . . . . . . . 123
▫ US/M Button . . . . . . . . . . . . . . . . . . . . . . . . 123
▫ Reset Button . . . . . . . . . . . . . . . . . . . . . . . . . 124
▫ Global Reset . . . . . . . . . . . . . . . . . . . . . . . . . 124
▫ Step Button . . . . . . . . . . . . . . . . . . . . . . . . . 124
▫ Average Fuel Economy (AVG ECO) . . . . . . . . 125
▫ Distance To Empty (DTE) . . . . . . . . . . . . . . . 12578 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
▫ Trip Odometer (ODO) . . . . . . . . . . . . . . . . . . 126
▫ Elapsed Time (ET) . . . . . . . . . . . . . . . . . . . . . 126
▫ C/T Button . . . . . . . . . . . . . . . . . . . . . . . . . 126
▫ Automatic Compass Calibration . . . . . . . . . . . 127
▫ Manual Compass Calibration . . . . . . . . . . . . . 127
▫ To Put Into a Calibration Mode . . . . . . . . . . . 128
▫ Outside Temperature . . . . . . . . . . . . . . . . . . . 129
䡵 Garage Door Opener — If Equipped . . . . . . . . . 130
▫ Programming Homelink . . . . . . . . . . . . . . . . 131
▫ Canadian Programming/Gate Programming . . 134
▫ Using Homelink . . . . . . . . . . . . . . . . . . . . . . 135
▫ Erasing Homelink Buttons . . . . . . . . . . . . . . . 135
▫ Reprogramming a Single Homelink Button . . . 135▫ Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . 136
䡵 Power Sunroof — If Equipped . . . . . . . . . . . . . 136
▫ Opening Sunroof - Express . . . . . . . . . . . . . . 137
▫ Closing Sunroof - Express . . . . . . . . . . . . . . . 137
▫ Pinch Protect Feature . . . . . . . . . . . . . . . . . . . 137
▫ Pinch Protect Override . . . . . . . . . . . . . . . . . 138
▫ Venting Sunroof - Express . . . . . . . . . . . . . . . 138
▫ Sunshade Operation . . . . . . . . . . . . . . . . . . . 138
▫ Wind Buffeting . . . . . . . . . . . . . . . . . . . . . . . 138
▫ Sunroof Maintenance . . . . . . . . . . . . . . . . . . . 139
▫ Ignition Off Operation . . . . . . . . . . . . . . . . . . 139
▫ Sunroof Fully Closed . . . . . . . . . . . . . . . . . . . 139
䡵 Electrical Power Outlets . . . . . . . . . . . . . . . . . . 139䡵 Cigar Lighter And Ash Receiver . . . . . . . . . . . . 140
䡵 Cupholders . . . . . . . . . . . . . . . . . . . . . . . . . . . 141▫ Front Instrument Panel Cupholders
— Automatic Transmission Only . . . . . . . . . . 141
▫ Rear Cupholder — Quad Cab
— If Equipped . . . . . . . . . . . . . . . . . . . . . . . 142
䡵 Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 142
▫ Center Storage Compartment — If Equipped . . 142UNDERSTANDING THE FEATURES OF YOUR VEHICLE 79
▫ Storage And Seats — If Equipped . . . . . . . . . . 143
䡵 Fold Flat Load Floor — If Equipped . . . . . . . . . 144
▫ Fold Flat Load Floor — If Equipped . . . . . . . . 144
䡵 Pickup Box . . . . . . . . . . . . . . . . . . . . . . . . . . . 147
䡵 Slide-In Campers . . . . . . . . . . . . . . . . . . . . . . . 148
䡵 Easy-Off Tailgate . . . . . . . . . . . . . . . . . . . . . . . 14880 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
POWER WAGON FEATURES
Locking Front and Rear Differentials Most 4WD trucks are equipped with open differentials front and rear. This design is used because it allows each wheel to turn independently helping to eliminate bind- ing when cornering. A disadvantage of using an open differential is when one or more wheels lose traction; all of the power is directed to those wheels resulting in a loss of momentum. The Power Wagon is equipped with electronically locking front and rear differentials. These differentials, when engaged, mechanically lock together the axle shafts forcing the wheels to spin at an equal rate. This allows the vehicle to maintain its momentum and thus prevents it from becoming stuck. The locking front and rear differentials should only be engaged during low-speed, extreme off-road situations where one wheel is likely to not be in contact with the ground. It is not
recommended to drive the vehicle with the differentials locked on pavement due to the reduced ability to turn and speed limitations. 4.56:1 Gears This is the highest axle ratio available in a full-size pickup. The high gearing helps to compensate for the increased rolling mass and increase diameter of the off-road tires. As well, there are many advantages to a higher axle ratio in off-road applications. When driving downhill the high gearing enables the driver to use the engine to slow the vehicle down in a more controlled manner. When driving up a steep grade, the ratio helps by keeping the truck in its power band helping to maintain upward momentum.
Electronically Disconnecting Stabilizer/Sway Bar Stabilizer bars are used to help distribute load force from one side of the vehicle to the other. This helps to reduce body roll and create a smoother ride during on-road driving. However, this becomes a disadvantage when the vehicle is driven off-road when a higher level of suspen- sion articulation is needed. By disconnecting the stabi- lizer bars, each wheel can now reach its maximum range of movement. This enables the vehicle to maintain a greater tire contact patch, and thus more traction, when traversing severe off-road terrain. Increased Ride Height Due to the use of longer springs and monotube shocks, the Power Wagon has an increased ride height of ap- proximately 1.4 inches in the front and 1.0 inch in the rear. It allows the truck to traverse larger obstructions and provides a better seating position from which to view the trail. A major advantage to increasing ride height is the positive effect it has on approach/departure
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 81
and break over angles. More ride height allows for more aggressive angles, further improving off-road capability. 12,000 lb. Winch The 2005 Power Wagon is the ⬙only pickup truck⬙ to offer an electric vehicle recovery winch from the factory. The winch provides the vehicle with an additional level of capability and versatility. This winch uses the electrical power from the vehicle charging system to power a motor that winds wire rope onto the winch drum via planetary gear reduction. By nature, a winch is capable of generating very high forces and should be used with care. Do not operate the winch without reading and understanding the complete winch section of owner’s manual, including all warnings and cautions.
82 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
High-Pressure Monotube Shocks/New Front and Rear Springs The new variable-rate shocks and revised springs help to create a suitable on-road ride without compromising off-road competency. The shocks are designed to provide improved stability, durability, and suspension articula- tion. Off-Road Tires These tires are specifically designed for extreme off-road use, while also maintaining quite on-road operation.The tires utilize long-life compounds for increased durability, and a deep-groove tread for extra traction. The LT285/ 70R17 used provides a large contact patch for better traction, two full-width steel belts for improved strength, as well as a reinforced sidewall to help protect against bruising and shredding.
Skid Plates And Underbody Protection Steel skid plates protect the major driveline components of the truck including the fuel tank, transfer case and steering damper. In addition the Power Wagon is equipped with boxed cross membes and fore/aft rails. This additional protection allows the vehicle to be uti- lized in severe off-road situations that would be consid- ered impassable by a normal truck. Wheel Flares Not just for looks, the wheel flares on the Power Wagon were designed to help cover its new larger off-road tires. The larger flares also help to reduce the amount of debris that can be flung up by the more aggressive tread pattern on the tires.
impingement damage.
Wheels Stylish forged aluminum 17⬙ wheels give the Power Wagon a powerful stance. Forging a wheel from alumi- num produces a stronger, lighter weight wheel than machining or casting the wheel out of the same material. Standard package features: • Fuel Tank Skid Plate - protects the fuel tank from • Transfer Case Skid Plate and Tubing - protects the transfer case and exhaust catalyst from impingement damage. • Heavy Duty Cross Members - protects the under carriage and supports the under body protection skid plates. • Fore/Aft rails - which connect the cross member for additional support and prevent the truck from getting hung up on large rocks between the cross members.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 83
dampener from impingement damage.
• Steering Dampener Skid Plate - protects the steering • Electronically Locking Front And Rear Axle Differen- tials With 4:56 Gears - improves mobility and articu- lation by locking the differentials. • Electronically Disconnecting Stabilizer/Sway Bar - im- proves mobility and articulation by disconnecting the Stabilizer/Sway Bar. • 160 Amp Alternator - supplies increased electrical power for the winch and other off-road accessories. • Heavy Duty Battery - supplies increased electrical power for the winch and other off-road accessories. • Heavy Duty Cooling Fan - provides enhanced engine and transmission cooling under vigorous off-road conditions.
84 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
mobility, ground clearance and ride comfort.
• Off-Road Tuned Suspension And Shocks - improves • Heavy Duty Thermally Protected and Sealed Electric Winch With Roller Fairlead - Useful for work and vehicle recovery. • 17 Inch Forged Aluminum Wheels With 33 Inch Tires - improves traction and differential ground clearance.
damage and provides a vehicle jacking point.
Mopar Options: • Rock Rails - protects the door sills from impingement • Winch accessory kit - Contents include: • Snatch Block/Pulley • Clevis • Tree strap • Tow Strap
• Gloves • “Power Wagon embossed” storage bag • Bed Liner - protects the bed from impingement dam-
age
NOTE: These Mopar options have been specially de- signed and tested for the Power Wagon to meet the vigorous off-road conditions.
MIRRORS
Inside Mirror The mirror should be adjusted to center on the view through the rear window. Annoying headlight glare can be reduced by moving the small control under the mirror to the night position (toward rear of vehicle). The mirror should be adjusted while set in the day position (toward windshield).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 85
Automatic Dimming Mirror— If Equipped This mirror automatically adjusts for annoying headlight glare from vehicles behind you. You can turn the feature on or off by pressing the button at the base of the mirror. A light in the button will indicate when the dimming feature is activated.
CAUTION!
To avoid damage to the mirror during cleaning, never spray any cleaning solution directly onto the mirror. Apply the solution onto a clean cloth and wipe the mirror clean.
Exterior Mirrors Folding Feature All 6 x 9 inch exterior mirrors are hinged and may be moved either forward or rearward to resist damage. The hinges have three detent positions; full forward, full rearward, and normal.
86 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
Outside Mirrors To receive maximum benefit, adjust the outside mirror(s) to center on the adjacent lane of traffic with a slight overlap of the view obtained on the inside mirror.
WARNING!
Vehicles and other objects seen in a right side convex mirror will look smaller and farther away than they really are. Relying too much on your right side convex mirror could cause you to collide with an- other vehicle or other object. Use your inside mirror when judging the size or distance of a vehicle seen in the right side convex mirror. Some vehicles will not have a convex right side mirror.
Electronic Power Mirrors — If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 87
The controls for the power mirrors are located on the driver’s door trim panel.
Set the top switch to the left or right for the left or right mirror, and set it to the center off position to prevent accidentally moving a mirror when you are finished adjusting the mirror. To adjust a mirror, select left or right with the top switch, and press one of the four arrows for the direction you want the mirror to move.
88 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
Electric Rear Window Defroster and Heated Sideview Mirrors — If Equipped
The Electric Rear Window Defroster and Heated side view mirrors are activated by pressing the heated grid button, located on the Climate Control panel, with the ignition On. Turning Off the ignition will deactivate the Electric Rear Window Defroster and Heated side view mirrors feature. These features also turn off after activation, when 15 minutes have elapsed. To reactivate, simply press the button again. Trailer Towing Mirrors — If Equipped These mirrors are designed with an adjustable mirror head to provide a greater vision range when towing extra-wide loads. To change position inboard or out- board, the mirror head should be rotated (flipped Out or In). A small blindspot mirror is integrated onto the main mirror surface.
NOTE: rearward prior to entering an automated car wash.
Fold the 7 x 10 inch trailer towing mirrors
CAUTION!
Do not attempt to fold the 7 x 10 inch trailer towing mirrors forward. The 7 x 10 inch trailer towing mirrors are not designed to be folded forward and doing so will damage the mirrors and/or vehicle.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 89
90 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
HANDS–FREE COMMUNICATION (UConnect™) — IF EQUIPPED UConnect™ is a voice-activated, hands-free, in-vehicle communications system. UConnect™; allows you to dial your cellular phone using simple voice commands (e.g., “Call” or “Dial”). Your cellular phone’s audio is trans- mitted through your vehicle’s stereo system; the system will automatically mute your radio before receiving or sending a call. UConnect™ allows you to transfer calls between the system and your cellular phone as you enter or exit your vehicle, and enables you to mute the system’s micro- phone for private conversations.
The UConnect™; phone book enables you to store up to 32 names and four numbers per name. This system is driven through your Bluetooth™ Hands-Free Profile cellular phone. UConnect™ features Bluetooth™ technol- ogy - the global standard that enables different electronic devices to connect to each other without wires or a docking station, so UConnect™ works no matter where you stow your cellular phone (be it your purse, pocket, or briefcase). UConnect™ allows up to seven cellular phones to be linked to the system, and it is available in English, French, or Spanish formats (as equipped). The rearview mirror contains the microphone for the system and the control buttons that will enable you to access the system. The diagram below shows the mirror with the appropriate buttons. Individual button behavior is discussed in the “Operation” Section.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 91
prompts as well as the other party’s voice in a conversa- tion will be played over your vehicle’s stereo system. The volume of the UConnect™ system can be controlled through your normal stereo controls. The radio display will be used for visual prompts from the UConnect™ system such as caller ID. Operation Voice commands can be used in the operation of the UConnect™ system and to navigate through the UCon- nect™ menu structure. Voice commands should be given after each UConnect™ system prompt. You will be prompted for a specific command and then guided through the available options. There are two ways to give commands to the UConnect™ system: • You can say ⬙Dial⬙ at the ⬙Ready⬙ prompt. When prompted for the phone number you wish to dial, say the phone number (⬙123 456 7890⬙).
The UConnect™ system can be used with any Hands Free Profile certified Bluetooth™ cellular phone. If your cellular phone has a different profile (i.e. headset profile), you will not be able to use any UConnect™ features. The UConnect™ system is fully integrated into your vehicle, including your vehicle’s stereo system. All voice
92 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
Pairing a Cellular Phone to the UConnect™ System To begin using your UConnect™ system, you must pair your compatible Bluetooth™ enabled cellular phone. To complete the registration process, you will need to refer- ence your cellular phone owner’s manual. • Press the ’Phone’ button to begin. • After the ⬙Ready⬙ prompt, say ⬙Setup⬙. • When prompted, say “ Phone Pairing”. • You will be asked to say a four-digit pin number into the UConnect™ system which you will later need to enter into your cellular phone during the cellular phone pairing process. You can enter any four-digit pin number. You will not need to remember this pin number after the initial registration process. • The UConnect™ system will then prompt you to begin the cellular phone pairing process on your cellular
phone. Please see your cellular phone user’s manual for instructions on how to complete this step. • For identification purposes, you will be prompted to give the UConnect™ system a name for your cellular phone. Each cellular phone that is paired should be given a unique phone name. • You will then be asked to give your cellular phone a priority level between 1 and 7, 1 having the highest priority. You can connect up to seven cellular phones to your UConnect™ system and the priority allows the UConnect™ system to know which cellular phone to use if multiple cellular phones are in the vehicle at the same time. For example, if a priority 3 and priority 5
cellular phone are both in the vehicle, the UConnect™ system will use the priority 3 cellular phone when you make a call. You can select to use a lower priority cellular phone at any time.Making a Phone Call Using Digit Dialing • Press the ’Phone’ button to begin. • After the ⬙Ready⬙ prompt, say ⬙Dial⬙ or ⬙Call⬙ followed by the phone number you wish to dial. For example, you can say ⬙Dial” wait for ready prompt 123 456 7890. The phone number that you enter must be a valid length.
Making a Phone Call Using Your UConnect™ Phonebook • Press the “Phone” button to begin. • After the ⬙Ready⬙ prompt, say ⬙Dial⬙ or ⬙Call⬙ wait for the ready prompt followed by the name and designa- tion of a phonebook entry that you wish to dial. For example, you can say ⬙Call John Doe Work⬙. Add Names to Your UConnect™ Phonebook • Press the “Phone” button to begin.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 93
try⬙.
• After the ⬙Ready⬙ prompt, say ⬙Phonebook New En- • Or, After the ⬙Ready⬙ prompt, say “Phonebook”. • When prompted, say “New Entry”. • When prompted, say the name of the new entry. • Next, enter the number designation (e.g. “Home”, “Work”, “Mobile”, or “Pager”). This will allow you to have multiple numbers for each phonebook entry. • Recite the phone number for the phonebook entry that
you are adding.
After you are finished adding an entry into the phone- book, you will be given the opportunity to add more phone numbers to the current entry or to return to the main menu.
94 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
The UConnect™ system will allow you to enter up to 32
names into the phonebook with each name having up to four associated phone numbers and designations. Edit Entries in the UConnect™ Phonebook • Press the ’Phone’ button to begin. • After the ⬙Ready⬙ prompt, say ⬙Phonebook Edit⬙. • You will then be asked for the name of the phonebook • Next, choose the number designation that you wish to edit. The choices are home, work, mobile, or pager. • Recite the new phone number for the phonebook entryentry that you wish to edit.
that you are editing.
After you are finished editing an entry in the phonebook, you will be given the opportunities to edit another entry in the phonebook, call the number you just edited, or return to the main menu.
Phonebook edit can be used to add another phone number to a name entry that already exists in the phonebook. For example, the entry John Doe may have a mobile and a home number, but you can add John Doe’s work number later through phonebook edit. Delete Entries in the UConnect™ Phonebook • Press the ’Phone’ button to begin. • After the ⬙Ready⬙ prompt, say ⬙Phonebook Delete⬙. • After you enter the phonebook delete menu, you will then be asked for the name of the phonebook entry that you wish to delete. You can either say the name of a phonebook entry that you wish to delete or you can say ⬙List Names⬙ to hear a list of the entries in the phonebook from which you can choose. To select one of the entries from the list, press the ⬙Voice Recogni- tion⬙ button while the UConnect™ system is playing the desired entry and say ⬙Delete⬙.
• After you enter the name, the UConnect™ system will ask you if you wish to delete the home, work, mobile, or pager number for this entry.
Delete All Entries in the UConnect™ Phonebook • Press the ’Phone’ button to begin. • After the ⬙Ready⬙ prompt, say ⬙Phonebook Delete All⬙. • The UConnect™ system will ask you to verify that you • After confirmation, the phonebook entries will be
wish to delete all the entries from the phonebook.
deleted.
List All Names in the UConnect™ Phonebook • Press the ’Phone’ button to begin. • After
the ⬙Ready⬙ prompt, say ⬙Phonebook List
Names⬙.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 95
phonebook entries.
• The UConnect™ system will play the names of all the • To call one of the names in the list, press the ’Voice Recognition’ button during the playing of the desired name and say ⬙Call⬙. • The UConnect™ system will then prompt you as to number designation you wish to call. • The selected number will be dialed. Phone Call Features The following feature(s) can be accessed through the UConnect™ system if the feature(s) are available on your cellular service plan. For example, if your cellular service plan provides three-way calling, this feature can be accessed through the UConnect™ system.
96 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
Answer or Reject an Incoming Call - No Call Currently in Progress When you receive a call on your cellular phone, the UConnect™ system will interrupt the stereo audio and will ask if you would like to answer the call by pressing the ’Phone’ button. Press the ’Phone’ button to answer the call. To reject the call, press the ’Phone’ button until you hear a single beep indicating that the incoming call was rejected. Answer or Reject an Incoming Call - Call Currently in Progress If a call is currently in progress and you have another incoming call, press the ’Phone’ button to place the current call on hold and answer the incoming call. To reject the incoming call, you can disregard the call and continue with your current conversation.
Making a Second Call while Current Call in Progress To make a second call while you are currently in a call, press the ’Voice Recognition’ button and say ⬙Dial⬙ or ⬙Call⬙ followed by the phone number or phonebook entry you wish to call. The first call will be on hold while the second call is in progress. Putting a Call on Hold and Retrieving a Call from Hold To put a call on hold, press the ’Phone’ button until you hear a single beep which will indicate that the call has been placed on hold. To bring the call back from hold, press the ’Phone’ button. Toggling Between Two Calls If two calls are in progress (one active and one on hold), press the ’Phone’ button until you hear a single beep
indicating that the active and hold status of the two calls have switched. Only one call can be placed on hold at one time. Conference Call When two calls are in progress (one active and one on hold), press the ’Phone’ button until you hear a double beep indicating that the two calls have been joined into one conference call. Three-Way Calling To initiate three-way calling, press the ’Voice Recogni- tion’ button while a call is in progress and make a second phone call. When the second call is established, press the ’Phone’ button until you hear a double beep indicating that the two calls have been joined into one conference call. Call Termination To end a call in progress, press the ’Phone’ button. All calls in progress will be terminated.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 97
Phone Redial • Press the ’Phone’ button to begin. • After the ⬙Ready⬙ prompt, say ⬙Redial⬙. • The UConnect™ system will call the last number that was dialed on your cellular phone. This may not be the last number dialed by your UConnect™ system.
Advanced Phone Connectivity
Transferring an Active Call between the UConnect™ System and Your Cellular Phone The UConnect™ system allows ongoing calls to be trans- ferred to your cellular phone or to the UConnect™ system without terminating the call. To transfer an ongo- ing call from your cellular phone to the UConnect™ system or vice versa, press the ’Voice Recognition’ button and say ⬙Transfer Call⬙.
98 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
Delete Paired Cellular Phones • Press the ’Phone’ button to begin. • After the ⬙Ready⬙ prompt, say ⬙Setup⬙. • When prompted, say “ Phone Pairing”. • At the next prompt, say ⬙Delete⬙. • You will be asked to say the name of the phone that you wish to delete. You can either say the name of the phone that you wish to delete or you can say ⬙All⬙ to delete all the phones.
Connect or Disconnect the Connection between the UConnect™ System and Your Cellular Phone Your cellular phone can be paired with many different electronic devices, but can only be actively ⬙connected⬙ with one electronic device at a time.
If you would like to connect or disconnect the Blue- tooth™ connection between a paired cellular phone and the UConnect™ system, follow the instruction described in your cellular phone user’s manual. List Paired Cellular Phone Names • Press the ’Phone’ button to begin. • After the ⬙Ready⬙ prompt, say ⬙Setup List Phones⬙ and the UConnect™ system will play the phone names of all paired cellular phones in order from highest prior- ity to lowest priority.
Select a Lower Priority Paired Cellular Phone • Press the ’Phone’ button to begin. • After the ⬙Ready⬙ prompt, say ⬙Setup⬙. • When prompted, say “Select Phone”.
• When prompted, say the phone name of the cellular phone you wish to use, or say ⬙List Phones⬙ to hear a list of all the phones that have been paired to your UConnect™ system. To select a phone from the list, press the ’Voice Recognition’ button and say ⬙Select⬙. • The lower priority phone will only be used for the next phone call. After that, the UConnect™ system will return to using the highest priority phone in the vehicle.
UConnect™ System Features
Barge In - Touch Tone Phone Inputs You can use your UConnect™ system to access a voice mail system, an automated service, or any other phone number that you can dial with any phone. When calling a number with your UConnect™ system that normally requires you to enter in a touch-tone sequence on your cellular phone keypad, you can push the ’Voice Recogni- tion’ button and say the sequence you wish to enter
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 99
followed by ⬙Send⬙. For example, if required to enter your pin number, you can press the ’Voice Recognition’ button and say ⬙3 7 4 6 Send⬙, or whatever you have made your pin. This method can also be used in instances where you are pressing a number on your keypad to navigate through a menu structure or to enter a number for a pager. Barge In - Overriding Prompts The ’Voice Recognition’ button can be used when you wish to skip part of a prompt and issue your voice recognition command immediately. For example, if a prompt is playing ⬙Would you like to pair a phone, clear aѧ⬙, you could press the ’Voice Recognition’ button and say ⬙Pair A Phone⬙ to select that option without having to listen to the rest of the voice prompt.
100 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
Language Selection To change the language that the UConnect™ system is using, press the ’Phone’ button and say the name of the language you wish to switch to (English, Español, or Français as equipped). After selecting one of the lan- guages, all prompts and voice commands will be in the selected language. Turning Confirmation Prompts On/Off Turning confirmation prompts off will stop the system from confirming your choices (e.g. the UConnect™ sys- tem will not repeat a phone number before you dial it). • Press the ’Phone’ button to begin. • After the ⬙Ready⬙ prompt, say ⬙Setup Confirmation⬙. The UConnect™ system will play the current confir- mation prompt status and you will be given the choice to change it.
Low Signal, Battery Strength, and Roam Notification The UConnect™ system will provide notification to inform you if your cellular phone is in roaming status, has low signal strength, or has a low battery when you are trying to place a phone call. Dialing Using the Cellular Phone Keypad You can dial a phone number with your cellular phone keypad and still use the UConnect™ system. By dialing a number with your paired Bluetooth™ cellular phone, the audio will be played through your vehicle’s stereo sys- tem. The UConnect™ system will work the same as if you dialed the number using voice recognition.
Mute/Unmute When you mute the UConnect™ system, you will still be able to hear the conversation coming from the other party, but the other party will not be able to hear you. In order to mute the UConnect™ system press the ’Voice Recognition’ button and say ⬙Mute⬙. In order to unmute the UConnect™ system; press the ’Voice Recognition’ button and say ⬙Unmute⬙. Help If you need assistance at any prompt or if you want to know what your options are at any prompt, say ⬙Help⬙. The UConnect™ system will play all the options at any prompt if you ask for help.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 101
Cancel At any prompt, you can say ⬙Cancel⬙ and you will be returned to the previous menu. Emergency Assistance If you are in an emergency, say ⬙Dial Emergency⬙ or ⬙Call Emergency⬙ and the UConnect™ system will instruct your cellular phone to call 911. Towing Assistance If you need towing assistance, say ⬙Dial Towing Assis- tance⬙ or ⬙Call Towing Assistance⬙. Please refer to the 24-Hour Towing Assistance coverage details in the DaimlerChrysler Motors Company 24-Hour Towing As- sistance Program Guide.
102 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
SEATS The seating options available in this truck are the result of extensive customer research and evaluations.
40-20-40 Front Seat
WARNING!
It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts. Be sure everyone in your vehicle is in a seat and using a seat belt properly.
As the name implies, the seat is divided into 3 segments. The outboard seat portions are each 40% of the total width of the seat. The back of the center portion (20%) easily folds down to provide an armrest/center storage compartment (if equipped).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 103
Reclining Seats The recliner handle is on the outside of the seat cushion. Pull up on the handle to release the seat back and adjust for comfort.
Each outboard seat is independently adjustable forward or backward and is equipped with a back recliner. The manual seat adjustment handle is found at the front edge of each seat cushion. Pull up on the handle and slide the seat to get the most comfortable position.
WARNING!
Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control. The seat belt might not be properly adjusted and you could be injured. Adjust any seat only while the vehicle is parked.
104 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
WARNING!
To lower the head restraint, push in the button and then push down on the head restraint.
You can be seriously, even fatally injured riding in a seat with the seatback reclined. Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest. If you ride in this position, the shoulder harness will no longer be restraining you. In a collision you could slide under the seat belt and receive serious or fatal injuries. Recline in a seat only when the vehicle is parked.
Adjustable Head Restraints Head restraints can reduce the risk of whiplash injury in the event of impact from the rear. Pull up or push down on the restraints so that the upper edge is as high as practical, at least to the level of the ears.
Manual Rotary Lumbar Support Adjustment — If Equipped Rotating the lumbar control knob on the left side of the driver’s seatback and on the right side of the passenger’s seatback increases or decreases the lumbar support.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 105
Power Seats — If Equipped
CAUTION!
Don’t put anything under a power seat. It may cause damage to the seat controls.
Manual Lumbar Adjustment
106 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
control seat height. Change the seat angle by using the two toggle switches, tilting it up or down.
Up, Down, Forward, and Rearward
The power seat controls are on the outboard side of the front seat cushions. Three switches control the seat move- ment. The four-way switch in the center can be moved forward or backwards to get the most comfortable posi- tion. The same switch can be moved up and down to
Tilt Adjustment
Heated Seats — If Equipped The heated seat switches are located in the instrument panel under the climate controls. The engine must be running for the heated seats to operate.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 107
Each heated seat switch has two settings (HI and LOW). Press the switch once to obtain the desired heating position and press a second time in the same direction to turn the heated seats OFF. If you do not purposefully turn the switch OFF, the heating element in the seat will remain activated until the ignition is turned off. The indicators on the switch will illuminate when the heated seats are in the (HI or LOW) position. Flashing telltale lights on the switch indicate that the Heated Seat system needs servicing.
Heated Seat Switches
108 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
TO OPEN AND CLOSE THE HOOD
To prevent possible damage, do not slam the hood to close it. Use a firm downward push at the front center of the hood to ensure that both latches engage.
To open the hood, two latches must be released. First pull the hood release lever located below the steering wheel at the base of the instrument panel. Once the hood is released you must reach into the opening beneath the center of the grille and push up the latch to release the safety catch before raising the hood.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 109
WARNING!
LIGHTS
If the hood is not fully latched, it could fly up when the vehicle is moving and block your forward vision. Be sure all hood latches are latched fully before driving.
110 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
Interior Lights
Courtesy/ dome lights are turned on when the front doors are opened, when the dimmer control (rotating wheel on the right side of the switch) is rotated to the second upward detent position, or if equipped, when the UNLOCK button is pressed on the key fob. Rotating the dimmer control to the optional fully upward position will
turn on the cargo light located on the back of the cab. When a door is open and the interior lights are on, rotating the dimmer control all the way down to the OFF detent will cause all the interior lights to go out. This is also known as the ⬙Party⬙ mode because it allows the doors to stay open for extended periods of time without discharging the vehicle’s battery. The brightness of the instrument panel lighting can be regulated by rotating the dimmer control up (brighter) or down (dimmer). When the headlights are ON you can supplement the brightness of the odometer, trip odom- eter, radio and overhead console by rotating the control up until you hear a click. This feature is termed the “Parade” mode and is useful when headlights are re- quired during the day.
Battery Saver To protect the life of your vehicle’s battery, Load Shed- ding is provided for both the interior and exterior lights. If the ignition is off and any door is left ajar for 15
minutes or the dimmer control is rotated upwards for 15
minutes, the interior lights will automatically turn off. If the headlamps remain on while the ignition is cycled off, the exterior lights will automatically turn off after 5
minutes. After 5 minutes timeout, if the headlamp switch is turned off and then turned on, the exterior lights will automatically turn off after 15 minutes. If the dimmer control is rotated to the cargo lamp position with the ignition off, the cargo lamps will automatically turn off after 15 minutes. NOTE: Battery Saver mode is cancelled if the ignition is ON.UNDERSTANDING THE FEATURES OF YOUR VEHICLE 111
Headlamp Delay — If Equipped To aid in your exit, your vehicle, if equipped, can be programmed by your dealer with a headlamp delay that will leave the headlamps on for 0, 30, 60, or 90 seconds. This delay is initiated when the ignition is turned OFF while the headlamp switch is on, and then the headlamp switch is cycled off. The headlamps will remain on for 60
seconds. Headlamp delay can be cancelled by either turning the headlamp switch ON then OFF or by turning the ignition ON. Headlights, Parking Lights, Panel LightsWhen the headlight switch is rotated to the first position, the parking lights, taillights, side marker lights, license plate light and instrument panel lights are all turned on. Rotating the headlight switch to the first position will also turn on the cab top clearance lights, flare lights, and tailgate lights if the vehicle is equipped with these lights. The headlights will turn ON when the switch is rotated to the second position. The
112 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
⬙LAMP OUT⬙ indicator will be illuminated in the instru- ment cluster if a defective bulb or wiring circuit is detected for the headlamp system.
Your vehicle is equipped with plastic headlight lenses that are lighter and less susceptible to stone breakage than glass headlights.
Plastic is not as scratch resistant as glass and therefore different lens cleaning procedures must be followed. To minimize the possibility of scratching the lenses and reducing light output, avoid wiping with a dry cloth. To remove road dirt, wash with a mild soap solution fol- lowed by rinsing. Do not use abrasive cleaning components, solvents, steel wool or other abrasive materials to clean the lenses. Daytime Running Lights (Canada and Fleet Vehicles Only) The headlights on your vehicle will illuminate when the engine is started. This provides a constant ⬙Lights ON⬙ condition until the ignition is turned OFF. The lights illuminate at less than normal intensity. If the parking brake is applied the Daytime Running Lights will turn off.
Lights-on Reminder If the headlights, parking lights, courtesy lights or cargo lights are left on, after the ignition is turned off, a continuous chime will sound when the driver’s door is opened. Fog Lights — If Equipped The foglights are turned ON by placing the headlight rotary control in the parking light or headlight position and pulling out the headlight rotary control. The fog lights will operate only when the parking lights are ON or when the vehicle headlights are ON low beam. An indicator light located left of the switch will illuminate when the fog lights are on. The fog lights will turn off when the switch is pressed in, when the headlight switch is rotated to the OFF position or the high beam is selected.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 113
CARGO LIGHT The cargo lights are turned on by rotating the dimmer control to the optional fully upward position. The cargo lights will also turn on for 30 seconds when a key fob Unlock is pressed, as part of the illuminated entry feature.
MULTIFUNCTION CONTROL LEVER The multifunction control lever is located on the left side of the steering column. Turn Signals Move the lever up or down to signal a right-hand or left-hand turn.
114 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
The arrow on either side of the instrument cluster flashes to indicate the direction of the turn, and proper operation of the front and rear turn signal lights. If a defective bulb or wiring circuit is detected for the turn signal system, the arrow indicators will flash at a faster rate. Also, the ⬙LAMP OUT⬙ indicator in the instrument cluster will be illuminated and a chime will be heard. If an indicator fails to light when the lever is moved, it would suggest that the switch or indicator lamp is defective. You can signal a lane change by moving the lever partially up or down.
Passing Light You can signal another vehicle with your headlights by partially pulling the multifunction lever toward the steer- ing wheel. This will cause the high beam headlights to turn on until the lever is released.
High Beam / Low Beam Select Switch Pull the multifunction control lever fully toward the steering wheel to switch the headlights from HIGH or LOW beam.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 115
Windshield Wipers
The wipers and washers are operated by a switch in the multifunction control lever. Turn the end of the handle to select the desired wiper speed.
116 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
Intermittent Wiper System
The intermittent feature of this system was designed for use when weather conditions make a single wiping cycle, with a variable pause between cycles, desirable. For maximum delay between cycles, rotate the control knob into the upper end of the delay range.
The delay interval decreases as you rotate the knob until it enters the LO continual speed position. The delay can be regulated from a maximum of about 15 seconds between cycles, to a cycle every 2 seconds. The delay intervals will double in duration when the vehicle speed is 10 mph (16 km) or less.
WARNING!
Sudden loss of visibility through the windshield could lead to an accident. You might not see other vehicles or other obstacles. To avoid sudden icing of the windshield during freezing weather, warm the windshield with defroster before and during wind- shield washer use.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 117
TILT STEERING COLUMN To tilt the column, push down on the lever below the turn signal control and move the wheel up or down, as desired. Release the lever to lock the column firmly in place.
Windshield Washers To use the washer, push in on the washer knob on the end of the multifunction control lever and hold while spray is desired. If the washer knob is depressed while in the delay range, the wiper will operate for several seconds after the washer knob is released. It will then resume the intermittent interval previously selected. If the washer knob is pushed, for a period greater than 1 second, while in the OFF position, the wiper will wipe approximately three wipes, after the wash knob is released. To prevent freeze-up of your windshield washer system in cold weather, select a solution or mixture that meets or exceeds the temperature range of your climate. This rating information can be found on most washer fluid containers.
118 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
WARNING!
Tilting the steering column while the vehicle is moving is dangerous. Without a stable steering col- umn, you could lose control of the vehicle and have an accident. Adjust the column only while the ve- hicle is stopped. Be sure it is locked before driving.
ELECTRONIC SPEED CONTROL — IF EQUIPPED When engaged, this device takes over accelerator opera- tion at speeds greater than (refer to the table below for the speed for your specific engine). The controls are mounted on the steering wheel.
To Activate Push the ON/OFF button to the ON position. In the instrument cluster, the word “CRUISE” illuminates when the system is on.
To Set At A Desired Speed When the vehicle has reached the desired speed, press and release the SET button. Release the accelerator and the vehicle will operate at the selected speed. To Deactivate A soft tap on the brake pedal, normal braking, clutch pressure while slowing the vehicle, or pressing the CAN- CEL button will deactivate speed control without erasing the memory. Pushing the ON/OFF button to the OFF position or turning off the ignition erases the memory.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 119
WARNING!
Leaving the Speed Control ON when not in use is dangerous. You could accidentally set the system to cause it to go faster than you want. You could lose control and have an accident. Always leave the system OFF when you aren’t using it.
To Resume Speed To resume a previously set speed, push and release the RESUME button. Resume can be used at any speed above (refer to the table below for the speed for your specific engine).
120 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
To Vary The Speed Setting When the speed control is on, speed can be increased by pressing and holding the ACCEL button. When the button is released, a new set speed will be established. Tapping the ACCEL button once will result in a speed increase (refer to the table below for the speed for your specific engine). Each time the button is tapped, speed increases so that tapping the button three times will increase speed by three increments.
Tapping the DECEL button once will result in a speed decrease (refer to the table below for the speed for your specific engine). Each time the button is tapped, speed will decrease. For example, tapping the button 3 times will decrease the speed by 3 times the speed listed in the table below (refer to the table below for the speed for your specific engine). To decrease speed while the speed control is on, press and hold the DECEL button. Release the button when the desired speed is reached, and the new speed will be set.
Functions Engage Speed Minimun RESUME Speed ACCEL Increase DECEL Decrease Dropout Speed
5.7L Engine 25 mph (40 km/h) 20 mph (32 km/h) 1 mph (2 km/h) 1 mph (2 km/h) 20 mph (32 km/h)
To Accelerate For Passing Depress the accelerator as you would normally. When the pedal is released, the vehicle will return to the set speed. NOTE: When driving uphill, at elevations above 2,000
feet (610 meters), or when the vehicle is heavily loaded (especially when towing) the vehicle may slow below the SET speed. If the vehicle speed drops below (refer to the table below for the speed for your specific engine), the speed control will automatically disengage. If this hap- pens, you can push down on the accelerator pedal to maintain the desired speed. Vehicles equipped with a 5–speed-manual transmission should be operated in 4th gear or lower under the above conditions.UNDERSTANDING THE FEATURES OF YOUR VEHICLE 121
Vehicles equipped with a Automatic transmission may exhibit several downshifts under the above conditions. To reduce the frequency of the downshifts and to im- prove vehicle performance, it is advisable to lock out overdrive by pressing the “TOW/HAUL” button located at the end of the gear shifter.
WARNING!
Speed Control can be dangerous where the system can’t maintain a constant speed. Your vehicle could go too fast for the conditions, and you could lose control. An accident could be the result. Don’t use Speed Control in heavy traffic or on roads that are winding, icy, snow-covered, or slippery.
122 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
OVERHEAD CONSOLE— IF EQUIPPED The two optional overhead consoles may consist of the following features:
• Courtesy/Reading Lights • Compass/Temperature Mini-Trip Computer (CMTC)
— If Equipped
• Universal Garage Door Opener — If Equipped Courtesy/Reading Lights In the middle of the console are two courtesy/reading lights. Both lights illuminate as courtesy lights when a door is opened, when the dimmer control is rotated to the courtesy light position (fully upward position), or when the UNLOCK button is pressed on the Remote Keyless Entry transmitter, if so equipped. These lights are also operated individually as reading lights by pressing the recessed area of the corresponding lens. NOTE: The courtesy/reading lights will remain on until the switch is pressed a second time, so be sure they have been turned off before leaving the vehicle. If the interior lights are left on after the vehicle is turned off, they will extinguish after 15 minutes.
OVERHEAD CONSOLE WITH COMPASS/TEMPERATURE MINI-TRIP COMPUTER — IF EQUIPPED This optional overhead console consists of the following: • Courtesy Lights • Compass/Temperature Mini-Trip Computer (CMTC)
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 123
This overhead console allows you to choose between a compass/temperature display and one of four trip con- ditions being monitored. US/M Button
Use this button to change the display from U.S. to metric measurement units.
124 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
RESET Button
Global Reset If the RESET button is pressed twice within 4 seconds while in any of the 3 resettable displays, the Global Reset will reset all 3 displays. Step Button
Use this button to reset the following displays to zero: Average Fuel Economy Trip Odometer Elapsed time
Use this button to choose or cycle through the four trip conditions.
Average Fuel Economy (AVG ECO) Shows the average fuel economy since the last reset. This display mode becomes less sensitive to instantaneous changes in fuel consumption as the number of total vehicle miles since the last reset increases. It is suggested that this mode be reset periodically for general operation or when driving conditions change significantly (for example, at the end of a trip or when a trailer is connected or disconnected). Distance To Empty (DTE) Shows the estimated distance that can be travelled with the fuel remaining in the tank. The estimated distance is determined by a weighted average of the instantaneous and average fuel economy, according to the current fuel tank level.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 125
When Distance To Empty = 0, the fuel gauge pointer will initially be on the red “E” marker. At this point (fuel gauge pointer on the red “E” marker) there is reserve fuel capacity, which corresponds to approximately 8% of tank volume. This reserve capacity was put in place to prevent the likelihood of customers running out of fuel when operating at maximum load conditions in areas where there aren’t many gas stations. NOTE: The Distance To Empty will remain equal to zero, until the vehicle runs out of fuel or is refueled. Ram fuel tank volumes are as follows: • 34 gallons - short box models • 35 gallons - long box models
126 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
Trip Odometer (ODO) This display shows the distance traveled since the last reset. Elapsed Time (ET) This display shows the accumulated ignition ON time since the last reset. C/T Button
Use this button to select a readout of the outside tem- perature and one of eight compass headings that indicate the direction in which the vehicle is facing.
WARNING!
Even if the display still reads a few degrees above 32°F ( 0°C), the road surface may be icy, particularly in woods or on bridges. Drive carefully under such conditions to prevent an accident and possible per- sonal injury or property damage.
Automatic Compass Calibration This compass is self-calibrating which eliminates the need to manually set the compass. When the vehicle is new, the compass may appear erratic and the CAL symbol will be displayed. After completing one 360° turn, with the vehicle traveling less than 5 mph (8 km/h), in an area free from large metal or metallic objects, the CAL symbol will turn off and the compass will function normally.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 127
Manual Compass Calibration
NOTE: To ensure proper compass calibration, make sure the compass variance is properly set before manu- ally calibrating the compass. If the compass appears erratic and the CAL symbol does not appear, you must manually put the compass into the “Calibration” mode.
128 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
To Put Into a Calibration Mode Turn on the ignition and set the display to “Compass/ Temperature.” Press and hold the RESET button to change the display between VAR (compass variance) and CAL (compass calibration) modes. When the CAL sym- bol is displayed complete one 360 degree turn in an area free from large metal objects or power lines. The CAL symbol will turn off and the compass will function normally.
Compass Variance is the difference between magnetic north and geographic north. In some areas of the country, the difference between magnetic and geographic north is great enough to cause the compass to give false readings. If this occurs, the compass variance must be set according to the Compass Variance Map.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 129
To set the variance: Turn the ignition ON and set the display to “Compass/Temperature.” Press the RESET button approximately five seconds. The last variance zone number will be displayed. Press the STEP button to select the new variance zone and press the RESET button to resume normal operation. Outside Temperature Because the ambient temperature sensor is located un- derhood, engine temperature can influence the displayed temperature, therefore, temperature readings are slowly updated when the vehicle speed is below 20 mph (30
km/h) or during stop and go driving.130 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
GARAGE DOOR OPENER — IF EQUIPPED The HomeLink威 Universal Transceiver replaces up to three remote controls (hand held transmitters) that oper- ate devices such as garage door openers, motorized gates, or home lighting. It triggers these devices at the push of a button. The Universal Transceiver operates off your vehicle’s battery and charging system; no batteries are needed.
For additional information on HomeLink威, call 1–800– 355–3515, or on the internet at www.homelink.com.
WARNING!
Programming HomeLink
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 131
A moving garage door can cause injury to people and pets in the path of the door. People or pets could be seriously or fatally injured. Only use this transceiver with a garage door opener that has a “stop and reverse” feature as required by federal safety stan- dards. This includes most garage door opener mod- els manufactured after 1982. Do not use a garage door opener without these safety features it could cause injury or death. Call toll-free 1–800–355–3515
or, on the Internet at www.homelink.com for safety information or assistance.NOTE: When programming a garage door opener, it is advised to park outside the garage. It is also recom- mended that a new battery be placed in the hand-held transmitter of the device being programmed to HomeLink for quicker training and accurate transmis- sion of the radio-frequency signal.
132 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
1. Press and hold the two outer HomeLink buttons, and release only when the indicator light begins to flash (after 20 seconds). Do not hold the buttons for longer than 30
seconds and do not repeat step one to program a second and/or third hand-held transmitter to the remaining two HomeLink buttons.WARNING!
Vehicle exhaust contains carbon monoxide, a danger- ous gas. Do not run the vehicle’s exhaust while training the transceiver. Exhaust gas can cause seri- ous injury or death.
WARNING!
Your motorized door or gate will open and close while you are training the Universal Transceiver. Do not train the transceiver if people or pets are in the path of the door or gate. A moving door or gate can cause serious injury or death to people and pets or damage to objects.
2. Position the end of your hand-held transmitter 1-3
inches (3-8 cm) away from the HomeLink buttons while keeping the indicator light in view. 3. Simultaneously press and hold both the HomeLink button that you want to train and the hand-held trans- mitter buttons. Do not release the buttons until step 4
has been completed. NOTE: Some gate operators and garage door openers may require you to replace this Programming Step 3 with procedures noted in the ⬙Gate Operator/Canadian Pro- gramming⬙ section. 4. The HomeLink indicator light will flash slowly and then rapidly after HomeLink successfully receives the frequency signal from the hand-held transmitter. Release both buttons after the indicator light changes from the slow to the rapid flash.UNDERSTANDING THE FEATURES OF YOUR VEHICLE 133
5. Press and hold the just trained HomeLink button and observe the indicator light. If the indicator light stays on constantly, programming is complete and your device should activate when the HomeLink button is pressed and released. NOTE: To program the remaining two HomeLink but- tons, begin with ⬙Programming⬙ step two. Do not repeat step one. If the indicator light blinks rapidly for two seconds and then turns to a constant light, continue with ⴖProgram- mingⴖ steps 6-8 to complete the programming of a rolling code equipped device (most commonly a garage door opener). 6. At the garage door opener receiver (motor-head unit) in the garage, locate the ⬙learn⬙ or ⬙smart⬙ button. This can usually be found where the hanging antenna wire is attached to the motor-head unit.
134 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
7. Firmly press and release the ⬙learn⬙ or ⬙smart⬙ button. (The name and color of the button may vary by manu- facturer.) NOTE: There are 30 seconds in which to initiate step eight. 8. Return to the vehicle and firmly press, hold for two seconds and release the programmed HomeLink button. Repeat the ⴖpress/hold/releaseⴖ sequence a second time, and, depending on the brand of the garage door opener (or other rolling code equipped device), repeat this sequence a third time to complete the programming. HomeLink should now activate your equipped device. NOTE: To program the remaining two HomeLink but- tons, begin with ⬙Programming⬙ step two. Do not repeat step one. For questions or comments, please contact HomeLink at www.homelink.com or 1-800-355-3515.
rolling code
Canadian Programming/Gate Programming Canadian radio-frequency laws require transmitter sig- nals to ⬙time-out⬙ (or quit) after several seconds of transmission which may not be long enough for HomeLink to pick up the signal during programming. Similar to this Canadian law, some U.S. gate operators are designed to ⬙time-out⬙ in the same manner. If you live in Canada or you are having difficulties programming a gate operator by using the ⬙Program- ming⬙ procedures (regardless of where you live), replace ⴖProgramming HomeLinkⴖ step 3 with the following: If programming a garage door opener or gate NOTE: operator, it is advised to unplug the device during the ⬙cycling⬙ process to prevent possible overheating. 3. Continue to press and hold the HomeLink button while you press and release every two seconds (⬙cycle⬙) your hand-held transmitter until the frequency signal has
successfully been accepted by HomeLink. (The indicator light will flash slowly and then rapidly.) Proceed with ⬙Programming⬙ step four to complete. Using HomeLink To operate, simply press and release the programmed HomeLink button. Activation will now occur for the trained device (i.e. garage door opener, gate operator, security system, entry door lock, home/office lighting, etc.). For convenience, the hand-held transmitter of the device may also be used at any time. In the event that there are still programming difficulties or questions, contact HomeLink at: www.homelink.com or 1-800-355- 3515. Erasing HomeLink Buttons To erase programming from the three buttons (individual buttons cannot be erased but can be ⬙reprogrammed⬙ - note below), follow the step noted:
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 135
• Press and hold the two outer HomeLink buttons until the indicator light begins to flash-after 20 seconds. Release both buttons. Do not hold for longer that 30
seconds. HomeLink is now in the train (or learning) mode and can be programmed at any time beginning with ⬙Programming⬙ - step 2.Reprogramming a Single HomeLink Button To program a device to HomeLink using a HomeLink button previously trained, follow these steps: 1. Press and hold the desired HomeLink button. DO NOT release the button. 2. The indicator light will begin to flash after 20 seconds. Without releasing the HomeLink button, proceed with ⬙Programming⬙ step 2
For questions or comments, contact HomeLink at: www.homelink.com or 1-800-355-3515.136 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
Security If you sell your vehicle, be sure to erase the frequencies. To erase all of the previously trained frequencies, hold down both outside buttons until the green light begins to flash. This device complies with part 15 of FCC rules and with RSS-210 of Industry Canada. Operation is subject to the following conditions: • This device may not cause harmful interference. • This device must accept any interference that may be received including interference that may cause undes- ired operation.
NOTE: Changes or modifications not expressly ap- proved by the party responsible for compliance could void the user’s authority to operate the equipment. HomeLink威 is a trademark owned by Johnson Controls, Inc.
POWER SUNROOF — IF EQUIPPED The power sunroof switch is located between the sun visors on the overhead console.
WARNING!
• Never leave children in a vehicle, with the keys in the ignition switch. Occupants, particularly unat- tended children, can become entrapped by the power sunroof while operating the power sunroof switch. Such entrapment may result in serious injury or death. • In an accident, there is a greater risk of being thrown from a vehicle with an open sunroof. You could also be seriously injured or killed. Always fasten your seat belt properly and make sure all passengers are properly secured too. • Do not allow small children to operate the sun- roof. Never allow fingers or other body parts, or any object to project through the sunroof opening. Injury may result.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 137
Opening Sunroof - Express Press the switch rearward and release, and the sunroof will open automatically from any position. The sunroof will open fully, then stop automatically. This is called Express Open. During Express Open operation, any movement of the sunroof switch will stop the sunroof. Closing Sunroof - Express Press the switch forward and release, and the sunroof will close automatically from any position. The sunroof will close fully and stop automatically. This is called Express Close. During Express Close operation, any movement of the switch will stop the sunroof. Pinch Protect Feature This feature will detect an obstruction in the opening of the sunroof during Express Close operation. If an ob- struction in the path of the sunroof is detected, the sunroof will automatically retract. Remove the obstruc- tion if this occurs. Next, press the switch forward and release to Express Close.
138 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
Pinch Protect Override If a known obstruction (ice, debris, etc.) prevents closing, press the switch forward and hold for two seconds after the reversal occurs. This allows the sunroof to move towards the closed position. NOTE: Pinch protection is disabled while the switch is pressed. Venting Sunroof - Express Press and release the ⬙V⬙ button, and the sunroof will open to the vent position. This is called Express Vent, and will occur regardless of sunroof position. During Express Vent operation, any movement of the switch will stop the sunroof.
Sunshade Operation The sunshade can be opened manually. However, the sunshade will open automatically as the sunroof opens. NOTE: The sunshade cannot be closed if the sunroof is open. Wind Buffeting Wind buffeting can be described as the perception of pressure on the ears or a helicopter type sound in the ears. Your vehicle may exhibit wind buffeting with the windows down, or the sunroof (if equipped) in certain open or partially open positions. This is a normal occur- rence and can be minimized. If the buffeting occurs with the rear windows open, open the front and rear windows together to minimize the buffeting. If the buffeting occurs with the sunroof open, adjust the sunroof opening to minimize the buffeting or open any window.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 139
There is an additional Power Outlet in the center console of a 40/20/40 seat (if equipped). The outlet(s) has/have a fused direct feed from the battery so it/they receive power whether the ignition is ON or OFF. All accessories connected to this/these outlet(s) should be removed or turned OFF when the vehicle is not in use to protect the battery against discharge.
Sunroof Maintenance Use only a non-abrasive cleaner and a soft cloth to clean the glass panel. Ignition Off Operation The power sunroof switches remain active for 10 minutes after the ignition switch has been turned off. Opening either front door will cancel this feature. Sunroof Fully Closed Press the switch forward and release to ensure that the sunroof is fully closed.
ELECTRICAL POWER OUTLETS The auxiliary electrical outlet can provide power for in cab accessories designed for use with the standard “cigar lighter” plug. The outlet is located in the instrument panel below the ash receiver. A cap is attached to the outlet base indicating “Power Outlet” 12V-20A.
140 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
CAUTION!
Electrical Outlet Use With Engine Off • Many accessories that can be plugged in draw power from the vehicle’s battery, even when not in use (i.e. cellular phones, etc.). Eventually, if plugged in long enough, the vehicle’s battery will discharge sufficiently to degrade battery life and/or prevent engine starting. • Accessories that draw higher power (i.e. coolers, vacuum cleaners, lights, etc.), will discharge the battery even more quickly. Only use these inter- mittently and with greater caution. • After the use of high power draw accessories, or long periods of the vehicle not being started (with accessories still plugged in), the vehicle must be driven a sufficient length of time to allow the generator to recharge the vehicle’s battery.
CIGAR LIGHTER AND ASH RECEIVER The ash receiver is opened and closed by pushing on the front surface of the receiver and then allowing the receiver to open. The cigar lighter is located above and to the left of the ash receiver. As a child safety precaution, the lighter only operates with the ignition switch ON. It heats when pushed in and pops out automatically when ready for use. To preserve the heating element, do not hold the lighter in the heating position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 141
closed by pushing on the front surface. Each opening in the cupholder is adjustable and will hold cups and mugs of various sizes. To secure the cup, place the cup to be held into one of the cup wells and then push the cupholder arm toward the cup until it is held stable.
CUPHOLDERS
Front Instrument Panel Cupholders — Automatic Transmission Only Your new Ram truck is equipped with dual-opening adjustable cupholders. The cupholder is opened and
Cupholders with Automatic
142 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
Rear Cupholder — Quad Cab — If Equipped Quad Cab vehicles may be equipped with a rear cup- holder that consists of two cupwells for rear passenger convenience.
STORAGE
Center Storage Compartment — If Equipped
The center portion of the seat folds down to provide an armrest with unique storage compartments under the lid. Push the button on the front of the armrest to raise the cover. Inside there is a power outlet (if equipped), removable coin holder (if equipped), and two dividers to configure the storage area into compartments. For ex- ample, compartments can be configured to hold a lap-top computer, a cellular telephone, CD’s and miscellaneous items. The top of the cover provides a generous firm surface to serve as a desktop for your “mobile office.”
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 143
The Quad Cab models provide additional storage under the rear seat. Lift the seat to access the storage compart- ment.
WARNING!
• This armrest is not a seat. Anyone seated on the armrest could be seriously injured during vehicle operation, or an accident. Only use the center seating position when the armrest is fully upright. • In an accident, the latch may open if the total weight of the items stored exceeds about 10 lbs (4.5 kg). These items could be thrown about endangering occupants of Items stored should not exceed a total of 10 lbs (4.5 kg).
the vehicle.
Storage and Seats — If Equipped Located in the center of the front 40/20/40 seat cushion there is a storage compartment. Standard cab models also have storage behind the seat.
144 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
FOLD FLAT LOAD FLOOR — IF EQUIPPED
Fold Flat Load Floor — If Equipped Quad Cab models with a 60/40 rear seat, may be equipped with a folding steel load floor.
WARNING!
Do not operate the vehicle with loose items stored on the load floor. While driving or in an accident you may experience, abrupt stopping, rapid acceleration, or sharp turns. Loose objects stored on the load floor may move around with force and strike occupants, resulting in serious or fatal injury.
Unfolding the Load Floor 1. Lift the 60/40 seat cushion(s) to the upward position.
2. Grasp the knob on the load floor and lift the knob until the load floor unfolds into position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 145
3. Reverse the procedure to store the load floor.
146 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
Positioning the Load Floor for Storage Access Under the Seat 1. Lift the 60/40 seat cushion(s) to the upward position. 2. Unsnap the securing snap located at either side of the load floor. 3. Lift the load floor up to access storage under the load floor.
WARNING!
Do not drive with the load floor in the up position. When stopping fast or in an accident, the load floor could move to the down position causing serious injury.
4. Reverse the procedure to put the load floor back in the secured down position before you operate the vehicle.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 147
You can carry wide building materials (sheets of ply- wood, etc.) by building a raised load floor. Place lumber across the box in the indentations provided above the wheel housings and in the bulkhead dividers to form the floor.
WARNING!
The pickup box is intended for load carrying pur- poses only, not for passengers, who should sit in seats and use seat belts.
PICKUP BOX
The pickup box on your new Ram has many features designed for utility and convenience. If you are installing a toolbox to the front of the NOTE: pickup box, you must use Mopar威 toolbox brackets available from your dealer.
148 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
WARNING!
• Care should always be exercised when operating a vehicle with unrestrained cargo. Vehicle speeds may need to be reduced. Severe turns or rough roads may cause shifting or bouncing of the cargo that may result in vehicle damage. If wide build- ing materials are to be frequently carried, the installation of a support is recommended. This will restrain the cargo and transfer the load to the pickup box floor. • If you wish to carry more than 600 lbs (272 kg) of material suspended above the wheelhouse, sup- ports must be installed to transfer the weight of the load to the pickup box floor or vehicle damage may result. The use of proper supports will permit loading up to the rated payload. • Unrestrained cargo may be thrown forward in an
accident causing serious or fatal injury.
There are stampings in the sheet metal on the inner side bulkheads of the box in front of and behind both wheel housings. Place wooden boards across the box from side to side to create separate load compartments in the pickup box. There are four tie-down cleats bolted to the lower sides of the pickup box that can sustain loads up to 1000 lbs (450
kg) total.SLIDE-IN CAMPERS DO NOT use slide-in campers on Power Wagon models.
EASY-OFF TAILGATE The tailgate can be removed quickly. Tailgate removal is sometimes required for pickup box loading. To remove the tailgate unlatch the tailgate and remove the support cables by releasing the lock tang from the pivot, then rotate and pull away from the box. Once the cables are free, move to the right side of the tailgate hinge bracket.
Raise the right side of the tailgate until the right side pivot clears the hanger bracket. Slide the entire tailgate to the right to free the left side pivot. Remove the tailgate from the vehicle entirely. Do not carry the tailgate loose in the truck pickup box. NOTE: Dual rear wheel pickup models require properly spaced rear clearance lights. If such a vehicle is operated without a tailgate, suitable lights must be installed.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 149
150 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
WARNING!
To avoid inhaling carbon monoxide, which is deadly, the exhaust system on vehicles equipped with “Cap or Slide-In Campers” should extend beyond the overhanging camper compartment and be free of leaks.
UNDERSTANDING YOUR INSTRUMENT PANEL
CONTENTS
䡵 Instruments And Controls . . . . . . . . . . . . . . . . . 155
䡵 Instrument Cluster . . . . . . . . . . . . . . . . . . . . . . 156
䡵 Instrument Cluster Description . . . . . . . . . . . . . 157
䡵 Electronic Digital Clock . . . . . . . . . . . . . . . . . . 165
▫ Clock Setting Procedure . . . . . . . . . . . . . . . . . 165䡵 Sales Code RBB—AM/FM Stereo Radio With
Cassette Tape Player And CD Changer Capability . . . . . . . . . . . . . . . . . . . . . . . . . . . . 166
▫ Radio Operation . . . . . . . . . . . . . . . . . . . . . . 166
▫ Mode Button . . . . . . . . . . . . . . . . . . . . . . . . 168▫ Scan Button (Radio Mode) . . . . . . . . . . . . . . . 168
▫ Cassette Player Features . . . . . . . . . . . . . . . . 169
▫ CD Changer Control Capability— If Equipped . . . . . . . . . . . . . . . . . . . . . . . 170
䡵 Sales Code RAZ—AM/ FM Stereo Radio With
Cassette Tape Player, CD Player And CD Changer Controls . . . . . . . . . . . . . . . . . . . . 172
▫ Operating Instructions — Radio . . . . . . . . . . . 172
▫ Power Switch, Volume Control . . . . . . . . . . . . 173
▫ Seek Button (Radio Mode) . . . . . . . . . . . . . . . 173152 UNDERSTANDING YOUR INSTRUMENT PANEL
▫ Tuning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 173
▫ Radio Data System (RDS) . . . . . . . . . . . . . . . 173
▫ PTY (Program Type) Button . . . . . . . . . . . . . . 174
▫ Balance . . . . . . . . . . . . . . . . . . . . . . . . . . . . 175
▫ Fade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 175
▫ Tone Control . . . . . . . . . . . . . . . . . . . . . . . . 175
▫ AM/FM Selection . . . . . . . . . . . . . . . . . . . . . 176
▫ Scan Button . . . . . . . . . . . . . . . . . . . . . . . . . 176
▫ To Set The Radio Push-Button Memory . . . . . . 176
▫ To Change From Clock To Radio Mode . . . . . . 177
▫ Operating Instructions — Tape Player . . . . . . . 177
▫ Seek Button . . . . . . . . . . . . . . . . . . . . . . . . . 177
▫ Fast Forward (FF) . . . . . . . . . . . . . . . . . . . . . 177▫ Rewind (RW) . . . . . . . . . . . . . . . . . . . . . . . . 177
▫ Tape Eject . . . . . . . . . . . . . . . . . . . . . . . . . . . 178
▫ Scan Button . . . . . . . . . . . . . . . . . . . . . . . . . 178
▫ Changing Tape Direction . . . . . . . . . . . . . . . . 178
▫ Metal Tape Selection . . . . . . . . . . . . . . . . . . . 178
▫ Pinch Roller Release . . . . . . . . . . . . . . . . . . . 178
▫ Noise Reduction . . . . . . . . . . . . . . . . . . . . . . 178
▫ Operating Instructions — CD Player . . . . . . . . 179
▫ Inserting The Compact Disc . . . . . . . . . . . . . . 179
▫ Seek Button . . . . . . . . . . . . . . . . . . . . . . . . . 180
▫ EJT CD (Eject) Button . . . . . . . . . . . . . . . . . . 180
▫ FF/Tune/RW . . . . . . . . . . . . . . . . . . . . . . . . 180
▫ Program Button 4 (Random Play) . . . . . . . . . . 180▫ Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 181
▫ Tape CD Button . . . . . . . . . . . . . . . . . . . . . . 181
▫ Time Button . . . . . . . . . . . . . . . . . . . . . . . . . 181
▫ Scan Button . . . . . . . . . . . . . . . . . . . . . . . . . 181
▫ CD Changer Control Capability— If Equipped . . . . . . . . . . . . . . . . . . . . . . . 181
䡵 Sales Code RBK—AM/ FM Stereo Radio With
CD Player And CD Changer Controls . . . . . . . . 183
▫ Radio Operation . . . . . . . . . . . . . . . . . . . . . . 183
▫ CD Player Operation . . . . . . . . . . . . . . . . . . . 185
▫ CD Changer Control Capability— If Equipped . . . . . . . . . . . . . . . . . . . . . . . 187
䡵 Sales Code RBQ—AM/FM Stereo Radio With
6 - Disc CD Changer
. . . . . . . . . . . . . . . . . . . . 189
UNDERSTANDING YOUR INSTRUMENT PANEL 153
▫ Radio Operation . . . . . . . . . . . . . . . . . . . . . . 190
▫ CD Player Operation . . . . . . . . . . . . . . . . . . . 192
䡵 Remote Sound System Controls — If Equipped . . 197
▫ Radio Operation . . . . . . . . . . . . . . . . . . . . . . 197
▫ Tape Player . . . . . . . . . . . . . . . . . . . . . . . . . 198
▫ CD Player . . . . . . . . . . . . . . . . . . . . . . . . . . 198
䡵 Cassette Tape And Player Maintenance . . . . . . . 198
䡵 Compact Disc Maintenance . . . . . . . . . . . . . . . . 199
䡵 Radio Operation And Cellular Phones . . . . . . . . 200
䡵 Climate Controls . . . . . . . . . . . . . . . . . . . . . . . 200
▫ Heater Only — Fleet Vehicles . . . . . . . . . . . . . 201
▫ Air Conditioning—If Equipped . . . . . . . . . . . 203154 UNDERSTANDING YOUR INSTRUMENT PANEL
▫ Electric Rear Window Defroster And Heated
Sideview Mirrors — If Equipped . . . . . . . . . . 207
▫ Air Conditioning With Dual Zone Temperature
Control — If Equipped . . . . . . . . . . . . . . . . . 207
▫ Operating Tips . . . . . . . . . . . . . . . . . . . . . . . 212
▫ Operating Tips Chart . . . . . . . . . . . . . . . . . . . 214INSTRUMENTS AND CONTROLS
UNDERSTANDING YOUR INSTRUMENT PANEL 155
156 UNDERSTANDING YOUR INSTRUMENT PANEL
INSTRUMENT CLUSTER
INSTRUMENT CLUSTER DESCRIPTION
1. Malfunction Indicator Light
This light is part of an onboard diagnostic system which monitors the emissions and engine control system. If the vehicle is ready for emissions testing the light will come on when the ignition is first turned on and remain on, as a bulb check, until the engine is started. If the vehicle is not ready for emissions testing the light will come on when the ignition is first turned on and remain on for 15 seconds, then blink for 5
seconds, and remain on until the vehicle is started. If the bulb does not come on during starting, have the condi- tion investigated promptly. If this light comes on and remains on while driving, it suggests a potential engine control problem and the need for system service.UNDERSTANDING YOUR INSTRUMENT PANEL 157
Although your vehicle will usually be drivable and not need towing, see your dealer for service as soon as possible.
CAUTION!
Prolonged driving with the MIL on could cause damage to the engine control system. It also could affect fuel economy and driveability. If the MIL is flashing, severe catalytic converter damage and power loss will soon occur. Immediate service is required.
158 UNDERSTANDING YOUR INSTRUMENT PANEL
2. Voltage Gauge
When the engine is running, the gauge indicates the electrical system voltage. The pointer should stay within the normal range if the battery is charged. If the pointer moves to either extreme left or right and remains there during normal driving, the electrical sys- tem should be serviced. If the gauge pointer moves to either extreme of NOTE: the gauge, the “Check Gages” indicator will illuminate and a single chime will sound. 3. Turn Signal Indicators Lights in instrument cluster flash when outside turn signals are operating. 4. Tachometer The tachometer indicates engine speed in revolutions per minute.
CAUTION!
Do not operate the engine with the tachometer pointer at high rpm for extended periods. Engine damage may occur.
5. Airbag Indicator Light The indicator lights and remains lit for 6 to 8 seconds when the ignition is first turned on. If the light stays on, flickers or comes on while driving, have the airbag system checked by an authorized dealer. 6. High Beam Indicator
This indicator shows that headlights are on high beam.
7. Seat Belt Reminder Light
When the ignition switch is first turned ON, this light will turn on for 5 to 8 seconds as a bulb check. During the bulb check, if the driver’s seat belt is unbuckled, a chime will sound. After the bulb check or when driving, if the driver seat belt remains unbuckled, the Seat Belt Warning Light will flash or remain on continuously. Refer to ⬙Enhanced Driver Seat Belt Re- minder System (BeltAlert™)⬙ in the Occupant Restraints section for more information. 8. Speedometer The speedometer shows the vehicle speed in miles per hour and/or kilometers per hour. 9. Oil Pressure Gauge
The pointer should always indicate some oil pres- sure when the engine is running. A continuous high or low reading, under normal driving conditions, may indicate a lubrication system malfunction. Immedi- ate service should be obtained.
UNDERSTANDING YOUR INSTRUMENT PANEL 159
If the gauge pointer moves to either extreme of NOTE: the gauge, the “Check Gages” indicator will illuminate and a single chime will sound. 10. Cargo Lamp The Cargo Lamp light will illuminate when the Cargo Lamp is activated from the dimmer control switch, located next to the headlight switch. 11. Door Ajar
The Door Ajar light will illuminate when any door is opened. When the ignition is ON the Door Ajar light will stay illuminated until the open door is closed. When the ignition is OFF the Door Ajar light will stay illuminated until the open door is closed or the battery saver feature automatically turns the light off.
160 UNDERSTANDING YOUR INSTRUMENT PANEL
