2010 Dodge Charger SRT8 Owners Manual

Download PDF Manual
collision. Rear seat belt assemblies must be replaced after a collision if they have been damaged (i.e., bent retractor, torn webbing, etc.). If there is any question regarding belt or retractor condition, replace the belt. Airbag Warning Light The light should come on and remain on for four to eight seconds as a bulb check when the ignition switch is first turned ON. If the light is not lit during starting, see your authorized dealer. If the light stays on, flickers, or comes on while driving, have the system checked by an autho- rized dealer. for service if your defroster Defroster Check operation by selecting the defrost mode and place the blower control on high speed. You should be able to feel the air directed against the windshield. See your authorized dealer is inoperable. Floor Mat Safety Information Always use floor mats designed to fit the foot well of your vehicle. Use only floor mats that leave the pedal area unobstructed and that are firmly secured so that they cannot slip out of position and interfere with the pedals or impair safe operation of your vehicle in other ways. WARNING! attached to the floor mat fasteners. Pedals that cannot move freely can cause loss of vehicle control and increase the risk of serious per- sonal injury. • Always make sure that floor mats are properly • Never place or install floor mats or other floor coverings in the vehicle that cannot be properly secured to prevent them from moving and inter- fering with the pedals or the ability to control the vehicle. • Never put floor mats or other floor coverings on top of already installed floor mats. Additional floor mats and other coverings will reduce the size of the pedal area and interfere with the pedals. (Continued) THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 77 WARNING! (Continued) • Check mounting of mats on a regular basis. Al- ways properly reinstall and secure floor mats that have been removed for cleaning. • Always make sure that objects cannot fall into the driver foot well while the vehicle is moving. Objects can become trapped under the brake pedal and accelerator pedal causing a loss of vehicle control. • If required, mounting posts must be properly installed, if not equipped from the factory. Failure to properly follow floor mat installation or mounting can cause interference with the brake pedal and accelerator pedal operation causing loss of control of the vehicle. 78 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Periodic Safety Checks You Should Make Outside the Vehicle Tires Examine tires for excessive tread wear and uneven wear patterns. Check for stones, nails, glass, or other objects lodged in the tread. Inspect the tread and sidewall for cuts and cracks. Check the wheel nuts for tightness. Check the tires (including spare) for proper pressure. Lights Have someone observe the operation of exterior lights while you work the controls. Check turn signal and high beam indicator lights on the instrument panel. Door Latches Check for positive closing, latching, and locking. Fluid Leaks Check area under vehicle after overnight parking for fuel, engine coolant, oil, or other fluid leaks. Also, if gasoline fumes are detected or if fuel, power steering fluid, or brake fluid leaks are suspected, the cause should be located and corrected immediately. UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS 䡵 Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83 ▫ Inside Day/Night Mirror . . . . . . . . . . . . . . . . 83 ▫ Automatic Dimming Mirror — If Equipped . . . 84 ▫ Outside Mirrors . . . . . . . . . . . . . . . . . . . . . . 84 ▫ Outside Mirrors Folding Feature — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . 85 ▫ Driver’s Outside Automatic Dimming Mirror — If Equipped . . . . . . . . . . . . . . . . . . . . . . . 85 ▫ Power Mirrors . . . . . . . . . . . . . . . . . . . . . . . 86 ▫ Heated Mirrors — If Equipped . . . . . . . . . . . . 86 ▫ Illuminated Vanity Mirrors — If Equipped . . . 87 䡵 Uconnect™ Phone — If Equipped . . . . . . . . . . . 87 ▫ Operation . . . . . . . . . . . . . . . . . . . . . . . . . . 89 ▫ Phone Call Features . . . . . . . . . . . . . . . . . . . 98 ▫ Uconnect™ Phone Features . . . . . . . . . . . . . 100 ▫ Advanced Phone Connectivity . . . . . . . . . . . 105 ▫ Things You Should Know About Your Uconnect™ Phone . . . . . . . . . . . . . . . . . . . . 107 ▫ General Information . . . . . . . . . . . . . . . . . . 116 䡵 Seats 80 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 䡵 Voice Command — If Equipped . . . . . . . . . . . 116 ▫ Voice Command System Operation . . . . . . . . 116 ▫ Commands . . . . . . . . . . . . . . . . . . . . . . . . 118 ▫ Voice Training . . . . . . . . . . . . . . . . . . . . . . 121 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121 ▫ Power Seats . . . . . . . . . . . . . . . . . . . . . . . . 122 ▫ Power Reclining Seats . . . . . . . . . . . . . . . . . 123 ▫ Lumbar Support . . . . . . . . . . . . . . . . . . . . . 124 ▫ Head Restraints . . . . . . . . . . . . . . . . . . . . . 124 ▫ Heated Seats . . . . . . . . . . . . . . . . . . . . . . . 126 ▫ Folding Rear Seat . . . . . . . . . . . . . . . . . . . . 127 䡵 To Open And Close The Hood . . . . . . . . . . . . 129 䡵 Lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130 ▫ Headlight Switch . . . . . . . . . . . . . . . . . . . . 130 ▫ Automatic Headlights — If Equipped . . . . . . 131 ▫ Headlights On With Wipers (Available With Automatic Headlights Only) . . . . . . . . . . . . 131 ▫ Headlight Time Delay . . . . . . . . . . . . . . . . . 132 ▫ Daytime Running Lights — If Equipped . . . . 132 ▫ Lights-On Reminder . . . . . . . . . . . . . . . . . . 132 ▫ Fog Lights . . . . . . . . . . . . . . . . . . . . . . . . . 133 ▫ Multifunction Lever . . . . . . . . . . . . . . . . . . 133 ▫ Turn Signals . . . . . . . . . . . . . . . . . . . . . . . . 134 ▫ Lane Change Assist . . . . . . . . . . . . . . . . . . . 134 ▫ High/Low Beam Switch . . . . . . . . . . . . . . . 134 ▫ Flash-To-Pass . . . . . . . . . . . . . . . . . . . . . . . 134 䡵 Windshield Wipers And Washers ▫ Overhead Console Map/Reading Lights . . . . 134 ▫ Interior Lights . . . . . . . . . . . . . . . . . . . . . . 135 . . . . . . . . . . 136 ▫ Intermittent Wiper System . . . . . . . . . . . . . . 137 ▫ Windshield Washers . . . . . . . . . . . . . . . . . . 137 ▫ Mist Feature . . . . . . . . . . . . . . . . . . . . . . . . 138 ▫ Headlights On With Wipers (Available With Automatic Headlights Only) . . . . . . . . . . . . 138 䡵 Tilt/Telescoping Steering Column . . . . . . . . . . 139 䡵 Adjustable Pedals — If Equipped . . . . . . . . . . 140 䡵 Electronic Speed Control . . . . . . . . . . . . . . . . 141 ▫ To Activate . . . . . . . . . . . . . . . . . . . . . . . . . 142 ▫ To Set At A Desired Speed . . . . . . . . . . . . . . 142 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 81 ▫ To Deactivate . . . . . . . . . . . . . . . . . . . . . . . 143 ▫ To Resume Speed . . . . . . . . . . . . . . . . . . . . 143 ▫ To Vary The Speed Setting . . . . . . . . . . . . . . 143 ▫ To Accelerate For Passing . . . . . . . . . . . . . . 144 䡵 Overhead Console . . . . . . . . . . . . . . . . . . . . . 145 ▫ Courtesy/Reading Lights . . . . . . . . . . . . . . 145 ▫ Sunglasses Storage . . . . . . . . . . . . . . . . . . . 145 䡵 Garage Door Opener — If Equipped . . . . . . . . 146 ▫ Programming HomeLink威 . . . . . . . . . . . . . . 147 ▫ Gate Operator/Canadian Programming . . . . 150 ▫ Using HomeLink威 . . . . . . . . . . . . . . . . . . . 150 ▫ Reprogramming A Single HomeLink威 Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . 151 82 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ Security . . . . . . . . . . . . . . . . . . . . . . . . . . . 151 ▫ Troubleshooting Tips . . . . . . . . . . . . . . . . . . 151 ▫ General Information . . . . . . . . . . . . . . . . . . 152 䡵 Power Sunroof — If Equipped . . . . . . . . . . . . 152 ▫ Opening Sunroof — Express . . . . . . . . . . . . 153 ▫ Closing Sunroof — Express . . . . . . . . . . . . . 153 ▫ Pinch Protect Feature . . . . . . . . . . . . . . . . . 153 ▫ Pinch Protect Override . . . . . . . . . . . . . . . . 154 ▫ Venting Sunroof — Express . . . . . . . . . . . . . 154 ▫ Sunshade Operation . . . . . . . . . . . . . . . . . . 154 ▫ Wind Buffeting . . . . . . . . . . . . . . . . . . . . . . 154 ▫ Sunroof Maintenance . . . . . . . . . . . . . . . . . 155 ▫ Ignition Off Operation . . . . . . . . . . . . . . . . . 155 ▫ Sunroof Fully Closed . . . . . . . . . . . . . . . . . . 155 䡵 Electrical Power Outlets . . . . . . . . . . . . . . . . . 155 䡵 Cupholders . . . . . . . . . . . . . . . . . . . . . . . . . . 158 ▫ Front Seat Cupholders . . . . . . . . . . . . . . . . . 158 ▫ Rear Seat Cupholders . . . . . . . . . . . . . . . . . 159 䡵 Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 159 . . . . . . . . . . . . . . . . . . . . 159 ▫ Console Features ▫ Cargo Area — Vehicles Equipped With 60/40 Split-Folding Rear Seat . . . . . . . . . . . . . . . . 160 䡵 Rear Window Features . . . . . . . . . . . . . . . . . . 162 ▫ Rear Window Defroster . . . . . . . . . . . . . . . . 162 MIRRORS Inside Day/Night Mirror A two-point pivot system allows for horizontal and vertical mirror adjustment. Adjust the mirror to center on the view through the rear window. Headlight glare can be reduced by moving the small control under the mirror to the night position (toward the rear of the vehicle). The mirror should be adjusted while set in the day position (toward the windshield). UNDERSTANDING THE FEATURES OF YOUR VEHICLE 83 Adjusting Rearview Mirror 84 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Automatic Dimming Mirror — If Equipped This mirror automatically adjusts for headlight glare from vehicles behind you. You can turn the feature on or off by pressing the button at the base of the mirror. A light next to the button will illuminate to indicate when the dimming feature is activated. CAUTION! To avoid damage to the mirror during cleaning, never spray any cleaning solution directly onto the mirror. Apply the solution onto a clean cloth and wipe the mirror clean. Outside Mirrors To receive maximum benefit, adjust the outside mirror(s) to center on the adjacent lane of traffic and a slight overlap of the view obtained from the inside mirror. NOTE: The passenger side convex outside mirror will give a much wider view to the rear, and especially of the lane next to your vehicle. Automatic Dimming Mirror UNDERSTANDING THE FEATURES OF YOUR VEHICLE 85 Driver’s Outside Automatic Dimming Mirror — If Equipped The driver’s outside mirror will automatically adjust for glare from vehicles behind you. This feature is controlled by the inside automatic dimming mirror and can be turned on or off by pressing the button at the base of the inside mirror. The mirror will automatically adjust for headlight glare when the inside mirror adjusts. WARNING! Vehicles and other objects seen in the passenger side convex mirror will look smaller and farther away than they really are. Relying too much on your passenger side convex mirror could cause you to collide with another vehicle or other object. Use your inside mirror when judging the size or distance of a vehicle seen in the passenger side convex mirror. Outside Mirrors Folding Feature — If Equipped Some models have outside mirrors that are hinged. The hinge allows the mirror to pivot forward and rearward to resist damage. The hinge has three detent positions: full forward, full rearward and normal. 86 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Power Mirrors The power mirror switch is located on the driver’s door trim panel, next to the power door lock switch. A rotary knob selects the left mirror, right mirror or off position. After selecting a mirror, move the knob in the same direction you want the mirror to move. Use the center off position to guard against accidentally moving a mirror position. Heated Mirrors — If Equipped These mirrors are heated to melt frost or ice. This feature is activated whenever you turn on the rear window defroster. Refer to “Rear Window Features” in “Understanding the Features of Your Vehicle” for further information. Power Mirror Control Illuminated Vanity Mirrors — If Equipped An illuminated vanity mirror is located on the sun visor. To use the mirror, rotate the sun visor downward and swing the mirror cover upward. The light turns on automatically. Closing the mirror cover turns off the light. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 87 Uconnect™ Phone — IF EQUIPPED Uconnect™ Phone is a voice-activated, hands-free, in- vehicle communications system. Uconnect™ Phone al- lows you to dial a phone number with your cellular phone using simple voice commands (e.g., ⬙Call” ѧ “Mike” ѧ”Work⬙ or ⬙Dial” ѧ “248-555-1212⬙). Your cellular phone’s audio is transmitted through your vehicle’s audio system; the system will automatically mute your radio when using the Uconnect™ Phone. NOTE: The Uconnect™ Phone requires a cellular phone equipped with the Bluetooth威 ⬙Hands-Free Profile,⬙ Ver- sion 0.96 or higher. See the Uconnect™ website for supported phones. Illuminated Vanity Mirror 88 UNDERSTANDING THE FEATURES OF YOUR VEHICLE For Uconnect™ customer support, visit the following websites: • www.chrysler.com/uconnect • www.dodge.com/uconnect • www.jeep.com/uconnect • or call 1–877–855–8400 Uconnect™ Phone allows you to transfer calls between the system and your cellular phone as you enter or exit your vehicle and enables you to mute the system’s microphone for private conversation. is driven through your The Uconnect™ Phone Bluetooth威 Profile” phone. “Hands-Free Uconnect™ features Bluetooth威 technology - the global standard that enables different electronic devices to con- nect to each other without wires or a docking station, so Uconnect™ Phone works no matter where you stow your cellular cellular phone (be it your purse, pocket, or briefcase), as long as your phone is turned on and has been paired to the vehicle’s Uconnect™ Phone. The Uconnect™ Phone allows up to seven cellular phones to be linked to the system. Only one linked (or paired) cellular phone can be used with the system at a time. The system is available in English, Spanish, or French languages. WARNING! Any voice commanded system should be used only in safe driving conditions following local laws and phone use. All attention should be kept on the roadway ahead. Failure to do so may result in an accident causing serious injury or death. Uconnect™ Phone Button Depending on the vehicle options, either the radio or the mirror will contain the two control (Uconnect™ Phone button) and buttons (Voice Command button) that will en- able you to access the system. Voice Command Button Actual button location may vary with the ra- dio. The individual buttons are described in the “Operation” section. The Uconnect™ Phone can be used with any Hands-Free Profile certified Bluetooth威 cellular phone. See the Uconnect™ website for supported phones. If your cellu- lar phone supports a different profile (e.g., Headset Profile) you may not be able to use any Uconnect™ Phone features. Refer to your cellular service provider or the phone manufacturer for details. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 89 The Uconnect™ Phone is fully integrated with the vehi- cle’s audio system. The volume of the Uconnect™ Phone can be adjusted either from the radio volume control knob or from the steering wheel radio control (right switch), if so equipped. The radio display will be used for visual prompts from the Uconnect™ Phone such as ⬙CELL⬙ or caller ID on certain radios. Operation Voice commands can be used to operate the Uconnect™ Phone and to navigate through the Uconnect™ Phone menu structure. Voice commands are required after most Uconnect™ Phone prompts. You will be prompted for a specific command and then guided through the available options. • Prior to giving a voice command, one must wait for the beep, which follows the ⬙Ready⬙ prompt or another prompt. 90 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • For certain operations, compound commands can be used. For example, instead of saying ⬙Setup⬙ and then ⬙Phone Pairing,⬙ the following compound command can be said: ⬙Setup Phone Pairing.⬙ • For each feature explanation in this section, only the combined form of the voice command is given. You can also break the commands into parts and say each part of the command when you are asked for it. For example, you can use the combined form voice com- mand ⬙Phonebook New Entry,⬙ or you can break the combined form command into two voice commands: ⬙Phonebook⬙ and ⬙New Entry.⬙ Please remember, the Uconnect™ Phone works best when you talk in a normal conversational tone, as if speaking to someone sitting a few feet/meters away from you. Voice Command Tree Refer to “Voice Tree” in this section. Help Command If you need assistance at any prompt, or if you want to know your options at any prompt, say ⬙Help⬙ following the beep. The Uconnect™ Phone will play all the options at any prompt if you ask for help. To activate the Uconnect™ Phone from idle, simply press button and follow the audible prompts for the directions. All Uconnect™ Phone sessions begin with a press of the button on the radio control head. Cancel Command At any prompt, after the beep, you can say ⬙Cancel⬙ and you will be returned to the main menu. However, in a few instances the system will take you back to the previous menu. Pair (Link) Uconnect™ Phone to a Cellular Phone To begin using your Uconnect™ Phone, you must pair your compatible Bluetooth威 enabled cellular phone. button to begin. To complete the pairing process, you will need to refer- ence your cellular phone Owner’s Manual. The Uconnect™ website may also provide detailed instruc- tions for pairing. The following are general phone to Uconnect™ Phone pairing instructions: • Press the • After the ⬙Ready⬙ prompt and the following beep, say • When prompted, after the beep, say ⬙Pair a Phone⬙ and • You will be asked to say a four-digit Personal Identi- fication Number (PIN), which you will later need to enter into your cellular phone. You can enter any four-digit PIN. You will not need to remember this PIN after the initial pairing process. follow the audible prompts. ⬙Setup Phone Pairing.⬙ UNDERSTANDING THE FEATURES OF YOUR VEHICLE 91 • For identification purposes, you will be prompted to give the Uconnect™ Phone a name for your cellular phone. Each cellular phone that is paired should be given a unique phone name. • You will then be asked to give your cellular phone a priority level between one and seven, with one being the highest priority. You can pair up to seven cellular phones to your Uconnect™ Phone. However, at any given time, only one cellular phone can be in use, connected to your Uconnect™ Phone. The priority allows the Uconnect™ Phone to know which cellular phone to use if multiple cellular phones are in the vehicle at the same time. For example, if priority three and priority five phones are present in the vehicle, the Uconnect™ Phone will use the priority three cellular phone when you make a call. You can select to use a lower priority cellular phone at any time (refer to ⬙Advanced Phone Connectivity⬙ in this section). ⬙Dial.⬙ button to begin. 92 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Dial by Saying a Number • Press the • After the ⬙Ready⬙ prompt and the following beep, say • The system will prompt you to say the number you • For example, you can say ⬙234-567-8901⬙. • The Uconnect™ Phone will confirm the phone number and then dial. The number will appear in the display of certain radios. want to call. Call by Saying a Name • Press the • After the ⬙Ready⬙ prompt and the following beep, say button to begin. “Call.⬙ person you want to call. • The system will prompt you to say the name of the • After the ⬙Ready⬙ prompt and the following beep, say the name of the person you want to call. For example, you can say ⬙John Doe,⬙ where John Doe is a previ- ously stored name entry in the Uconnect™ phonebook or downloaded phonebook. To learn how to store a name in the phonebook, refer to ⬙Add Names to Your Uconnect™ Phonebook,⬙ in the phonebook. • The Uconnect™ system will confirm the name and then dial the corresponding phone number, which may appear in the display of certain radios. Add Names to Your Uconnect™ Phonebook NOTE: Adding names to the Uconnect™ Phonebook is recommended when the vehicle is not in motion. • Press the button to begin. ⬙Phonebook New Entry.⬙ • After the ⬙Ready⬙ prompt and the following beep, say • When prompted, say the name of the new entry. Use of long names helps the Voice Command and it is recom- mended. For example, say ⬙Robert Smith⬙ or ⬙Robert⬙ instead of ⬙Bob.⬙ • When prompted, enter the number designation (e.g., ⬙Home,⬙ ⬙Work,⬙ ⬙Mobile,⬙ or ⬙Pager⬙). This will allow you to store multiple numbers for each phonebook entry, if desired. • When prompted, recite the phone number for the phonebook entry that you are adding. After you are finished adding an entry into the phone- book, you will be given the opportunity to add more phone numbers to the current entry or to return to the main menu. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 93 The Uconnect™ Phone will allow you to enter up to 32 names in the phonebook with each name having up to four associated phone numbers and designations. Each language has a separate 32-name phonebook accessible only in that language. In addition, if equipped and supported by your phone, Uconnect™ Phone automati- cally downloads your cellular phone’s phonebook. Phonebook Download – Automatic Phonebook Transfer From Cellular Phone If equipped and specifically supported by your phone, Uconnect™ Phone automatically downloads names (text names) and number entries from the cellular phone’s phonebook. Specific Bluetooth威 Phones with Phone Book Access Profile may support this feature. See Uconnect™ website for supported phones. • To call a name from downloaded (or Uconnect™) Phonebook, follow the procedure in “Call by Saying a Name” section. 94 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Automatic download and update, if supported, begins as soon as the Bluetooth威 wireless phone connection is made to the Uconnect™ Phone, for example, after you start the vehicle. • A maximum of 1000 entries per phone will be down- loaded and updated every time a phone is connected to the Uconnect™ Phone. • Depending on the maximum number of entries down- loaded, there may be a short delay before the latest downloaded names can be used. Until then, if avail- able, the previous downloaded phonebook is available for use. • Only the phonebook of the currently connected cellu- • Only the cellular phone’s phonebook is downloaded. SIM card phonebook is not part of the Mobile phone- book. lar phone is accessible. • This downloaded phonebook cannot be edited or deleted on the Uconnect™ Phone. These can only be edited on the cellular phone. The changes are trans- ferred and updated to Uconnect™ Phone on the next phone connection. Phonebook Download — Single Entry If equipped and supported by your phone, Uconnect™ Phone allows the user to download entries from their phone via Bluetooth威. To use this feature, press the button and say “Phonebook Download.” The system prompts, “Ready to accept “V” card entry via Bluetooth威…” The system is now ready to accept phone- book entries from your phone using the Bluetooth威 Object Exchange Profile (OBEX). Please see your phone Owner’s Manual for specific instructions on how to send these entries from your phone. transfers of phonebook entries to use this feature. NOTE: • The phone handset must support Bluetooth威 OBEX • Some phones cannot send phonebook entries if they are already connected to any system via Bluetooth威, and you may see a message on the phone display that the Bluetooth威 link is busy. In this case, the user must first disconnect or drop the Bluetooth威 connection to the Uconnect™ Phone, and then send the address book entry via Bluetooth威. Please see your phone Owner’s Manual for specific instructions on how to drop the Bluetooth威 connection. • If the phonebook entry is longer than 24 characters, it will only use the first 24 characters. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 95 deleted or edited. when the vehicle is not in motion. Edit Uconnect™ Phonebook Entries NOTE: • Editing names in the phonebook is recommended • Automatic downloaded phonebook entries cannot be • Press the • After the ⬙Ready⬙ prompt and the following beep, say • You will then be asked for the name of the phonebook • Next, choose the number designation (home, work, • When prompted, recite the new phone number for the cellular, or pager) that you wish to edit. entry that you wish to edit. ⬙Phonebook Edit.⬙ button to begin. phonebook entry that you are editing. 96 UNDERSTANDING THE FEATURES OF YOUR VEHICLE After you are finished editing an entry in the phonebook, you will be given the opportunity to edit another entry in the phonebook, call the number you just edited, or return to the main menu. ⬙Phonebook Edit⬙ can be used to add another phone number to a name entry that already exists in the phonebook. For example, the entry John Doe may have a cellular and a home number, but you can add ”John Doe’s” work number later using the ⬙Phonebook Edit⬙ feature. Delete Uconnect™ Phonebook Entry NOTE: Editing phonebook entries is recommended when the vehicle is not in motion. • Press the button to begin. • After the ⬙Ready⬙ prompt and the following beep, say ⬙Phonebook Delete.⬙ • After you enter the Phonebook Delete menu, you will then be asked for the name of the entry that you wish to delete. You can either say the name of a phonebook entry that you wish to delete or you can say ⬙List Names⬙ to hear a list of the entries in the phonebook from which you choose. To select one of the entries button while the from the list, press the Uconnect™ Phone is playing the desired entry and say ⬙Delete.⬙ • After you enter the name, the Uconnect™ Phone will ask you which designation you wish to delete: home, work, cellular, pager, or all. Say the designation you wish to delete. • Note that only the phonebook entry in the current • Automatic downloaded phonebook entries cannot be language is deleted. deleted or edited. button to begin. ⬙Phonebook Erase All.⬙ Delete/Erase “All” Uconnect™ Phonebook Entries • Press the • After the ⬙Ready⬙ prompt and the following beep, say • The Uconnect™ Phone will ask you to verify that you • After confirmation, the phonebook entries will be • Note that only the phonebook in the current language • Automatic downloaded phonebook entries cannot be wish to delete all the entries from the phonebook. is deleted. deleted. deleted or edited. List All Names in the Uconnect™ Phonebook • Press the button to begin. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 97 ⬙Phonebook List Names.⬙ • After the ⬙Ready⬙ prompt and the following beep, say • The Uconnect™ Phone will play the names of all the phonebook entries, including the downloaded phone- book entries, if available. • To call one of the names in the list, press the button during the playing of the desired name, and say ⬙Call.⬙ NOTE: The user can also exercise ⬙Edit⬙ or ⬙Delete⬙ operations at this point. • The Uconnect™ Phone will then prompt you as to the number designation you wish to call. • The selected number will be dialed. 98 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Phone Call Features The following features can be accessed through the Uconnect™ Phone if the feature(s) are available on your cellular service plan. For example, if your cellular service plan provides three-way calling, this feature can be accessed through the Uconnect™ Phone. Check with your cellular service provider for the features that you have. Answer or Reject an Incoming Call - No Call Currently in Progress When you receive a call on your cellular phone, the Uconnect™ Phone will interrupt the vehicle audio sys- tem, if on, and will ask if you would like to answer the button to accept the call. To reject the call. Press the button until you hear a call, press and hold the single beep, the incoming call was rejected. indicating that Answer or Reject an Incoming Call - Call Currently in Progress If a call is currently in progress and you have another incoming call, you will hear the same network tones for call waiting that you normally hear when using your button to place the current cellular phone. Press the call on hold and answer the incoming call. NOTE: The Uconnect™ Phone compatible phones in the market today do not support rejecting an incoming call when another call is in progress. Therefore, the user can only answer an incoming call or ignore it. Making a Second Call While Current Call is in Progress To make a second call while you are currently on a call, button and say ⬙Dial⬙ or ⬙Call⬙ followed press the by the phone number or phonebook entry you wish to call. The first call will be on hold while the second call is in progress. To go back to the first call, refer to ⬙Toggling Between Calls⬙ in this section. To combine two calls, refer to ⬙Conference Call⬙ in this section. Place/Retrieve a Call From Hold To put a call on hold, press the button until you hear a single beep. This indicates that the call is on hold. To bring the call back from hold, press and hold the button until you hear a single beep. Toggling Between Calls If two calls are in progress (one active and one on hold), press the button until you hear a single beep, indicat- ing that the active and hold status of the two calls have switched. Only one call can be placed on hold at a time. Conference Call When two calls are in progress (one active and one on button until you hear a hold), press and hold the double beep indicating that the two calls have been joined into one conference call. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 99 Three-Way Calling To initiate three-way calling, press the button while a call is in progress, and make a second phone call, as described under ⬙Making a Second Call While Current Call is in Progress.⬙ After the second call has established, button until you hear a double press and hold the beep, indicating that the two calls have been joined into one conference call. Call Termination To end a call in progress, momentarily press the button. Only the active call(s) will be terminated and if there is a call on hold, it will become the new active call. If the active call is terminated by the phone far end, a call on hold may not become active automatically. This is cell phone-dependent. To bring the call back from hold, press and hold the button until you hear a single beep. Redial • Press the button to begin. 100 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • After the ⬙Ready⬙ prompt and the following beep, say • The Uconnect™ Phone will call the last number that ⬙Redial.⬙ was dialed from your cellular phone. NOTE: This may not be the last number dialed from the Uconnect™ Phone. Call Continuation Call continuation is the progression of a phone call on the Uconnect™ Phone after the vehicle ignition key has been switched to OFF. Call continuation functionality avail- able on the vehicle can be any one of three types: • After the ignition key is switched to OFF, a call can continue on the Uconnect™ Phone either until the call ends, or until the vehicle battery condition dictates cessation of the call on the Uconnect™ Phone and transfer of the call to the cellular phone. • After the ignition key is switched to OFF, a call can continue on the Uconnect™ Phone for a certain dura- tion, after which the call is automatically transferred from the Uconnect™ Phone to the cellular phone. • An active call is automatically transferred to the cellular phone after the ignition key is switched to OFF. Uconnect™ Phone Features Language Selection To change the language that the Uconnect™ Phone is using: • Press the • After the ⬙Ready⬙ prompt and the following beep, say the name of the language you wish to switch to English, Espanol, or Francais. button to begin. • Continue to follow the system prompts to complete the language selection. After selecting one of the languages, all prompts and voice commands will be in that language. NOTE: After every Uconnect™ Phone language change operation, only the language-specific 32-name phone- book is usable. The paired phone name is not language- specific and usable across all languages. Emergency Assistance If you are in an emergency and the cellular phone is reachable: • Pick up the phone and manually dial the emergency number for your area. If the phone is not reachable and the Uconnect™ Phone is operational, you may reach the emergency number as follows: button to begin. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 101 • Press the • After the ⬙Ready⬙ prompt and the following beep, say ⬙Emergency⬙ and the Uconnect™ Phone will instruct the paired cellular phone to call the emergency num- ber. This feature is supported in the U.S., Canada, and Mexico. NOTE: • The emergency number dialed is based on the country where the vehicle is purchased (911 for the U.S. and Canada and 060 for Mexico). The number dialed may not be applicable with the available cellular service and area. • If supported, this number may be programmable on button and some systems. To do this, press the say ‘Setup’, followed by ‘Emergency’. 102 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • The Uconnect™ Phone does slightly lower your chances of successfully making a phone call as to that for the cellular phone directly. WARNING! Your phone must be turned on and paired to the Uconnect™ Phone System to allow use of this vehicle feature in emergency situations, when the cellular phone has network coverage and stays paired to the Uconnect™ Phone System. Towing Assistance If you need towing assistance: • Press the • After the ⬙Ready⬙ prompt and the following beep, say button to begin. ⬙Towing Assistance.⬙ NOTE: • The towing assistance number dialed is based on the country where the vehicle is purchased (1-800-528- 2069 for the U.S., 1-877-213-4525 for Canada, 55-14- 3454 for Mexico City and 1-800-712-3040 for outside Mexico City in Mexico). Please refer to the 24-Hour ⬙Towing Assistance⬙ coverage details on the DVD in the Warranty Information Booklet and the 24-Hour Towing Assistance references. • If supported, this number may be programmable on button and some systems. To do this, press the say “Setup”, followed by “Towing Assistance”. Paging To learn how to page, refer to ⬙Working with Automated Systems.⬙ Paging works properly except for pagers of certain companies, which time out a little too soon to work properly with the Uconnect™ Phone. Voice Mail Calling To learn how to access your voice mail, refer to ⬙Working with Automated Systems.⬙ Working with Automated Systems This method is used in instances where one generally has to press numbers on the cellular phone keypad while navigating through an automated telephone system. You can use your Uconnect™ Phone to access a voice mail system or an automated service, such as a paging service or automated customer service line. Some ser- vices require immediate response selection. In some instances, the Uconnect™ Phone. When calling a number with your Uconnect™ Phone that normally requires you to enter in a touch-tone sequence on your cellular phone keypad, you can press the button and say the sequence you wish to enter, followed by the word ⬙Send.⬙ For example, if required to enter that may be too quick for use of UNDERSTANDING THE FEATURES OF YOUR VEHICLE 103 your PIN followed with a pound, (3 7 4 6 #), you can button and say, ⬙3 7 4 6 #Send.⬙ Saying press the a number, or sequence of numbers, followed by ⬙Send,⬙ is also to be used for navigating through an automated customer service center menu structure, and to leave a number on a pager. You can also send stored Uconnect™ phonebook entries as tones for fast and easy access to voice mail and pager entries. To use this feature, dial the number you wish to button and say, “Send.” The call and then press the system will prompt you to enter the name or number and say the name of the phonebook entry you wish to send. The Uconnect™ Phone will then send the corresponding phone number associated with the phonebook entry, as tones over the phone. NOTE: • You may not hear all of the tones due to cellular phone network configurations. This is normal. 104 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Some paging and voice mail systems have system time out settings that are too short and may not allow the use of this feature. Barge In - Overriding Prompts The “Voice Command” button can be used when you wish to skip part of a prompt and issue your voice command immediately. For example, if a prompt is asking ⬙Would you like to pair a phone, clear a...,⬙ you button and say, ⬙Pair a Phone⬙ to could press the select that option without having to listen to the rest of the voice prompt. Turning Confirmation Prompts ON/OFF Turning confirmation prompts off will stop the system from confirming your choices (e.g., the Uconnect™ Phone will not repeat a phone number before you dial it). • Press the button to begin. • After the ⬙Ready⬙ prompt and the following beep, say ⬙Setup Confirmations.⬙ The Uconnect™ Phone will play the current confirmation prompt status and you will be given the choice to change it. Phone and Network Status Indicators If available on the radio and/or on a premium display such as the instrument panel cluster, and supported by your cellular phone, the Uconnect™ Phone will provide notification to inform you of your phone and network status when you are attempting to make a phone call using Uconnect™ Phone. The status is given for roaming, network signal strength, phone battery strength, etc. Dialing Using the Cellular Phone Keypad You can dial a phone number with your cellular phone keypad and still use the Uconnect™ Phone (while dialing via the cellular phone keypad, the user must exercise caution and take precautionary safety measures). By dialing a number with your paired Bluetooth威 cellular phone, the audio will be played through your vehicle’s audio system. The Uconnect™ Phone will work the same as if you dial the number using Voice Command. NOTE: Certain brands of cellular phones do not send the dial ring to the Uconnect™ Phone to play it on the vehicle audio system, so you will not hear it. Under this situation, after successfully dialing a number the user may feel that the call did not go through even though the call is in progress. Once your call is answered, you will hear the audio. Mute/Un-Mute (Mute OFF) When you mute the Uconnect™ Phone, you will still be able to hear the conversation coming from the other party, but the other party will not be able to hear you. In order to mute the Uconnect™ Phone: • Press the • Following the beep, say ⬙Mute.⬙ button. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 105 In order to un-mute the Uconnect™ Phone: • Press the • Following the beep, say ⬙Mute off.⬙ Advanced Phone Connectivity button. Transfer Call to and from Cellular Phone The Uconnect™ Phone allows ongoing calls to be trans- ferred from your cellular phone to the Uconnect™ Phone without terminating the call. To transfer an ongoing call from your Uconnect™ Phone paired cellular phone to the button Uconnect™ Phone or vice versa, press the and say ⬙Transfer Call.⬙ Connect or Disconnect Link Between the Uconnect™ Phone and Cellular Phone Your cellular phone can be paired with many different electronic devices, but can only be actively ⬙connected⬙ with one electronic device at a time. button to begin. 106 UNDERSTANDING THE FEATURES OF YOUR VEHICLE If you would like to connect or disconnect the Bluetooth威 connection between a Uconnect™ Phone paired cellular phone and the Uconnect™ Phone, follow the instructions described in your cellular phone User’s Manual. List Paired Cellular Phone Names • Press the • After the “Ready” prompt and the following beep, say • When prompted, say ⬙List Phones.⬙ • The Uconnect™ Phone will play the phone names of all paired cellular phones in order from the highest to the lowest priority. To “select” or “delete” a paired button and phone being announced, press the say “Select” or “Delete.” Also, see the next two sec- tions for an alternate way to “select” or “delete” a paired phone. “Setup Phone Pairing.” button to begin. ⬙Setup Select Phone⬙ and follow the prompts. Select Another Cellular Phone This feature allows you to select and start using another phone paired with the Uconnect™ Phone. • Press the • After the ⬙Ready⬙ prompt and the following beep, say • You can also press the button at any time while the list is being played, and then choose the phone that you wish to select. • The selected phone will be used for the next phone call. the Uconnect™ Phone will return to using the highest priority phone present in or near (approximately within 30 ft (9 m)) the vehicle. the selected phone is not available, If Delete Uconnect™ Phone Paired Cellular Phones • Press the button to begin. ⬙Setup Phone Pairing.⬙ • After the ⬙Ready⬙ prompt and the following beep, say • At the next prompt, say ⬙Delete⬙ and follow the • You can also press the button at any time while the list is being played, and then choose the phone you wish to delete. prompts. Things You Should Know About Your Uconnect™ Phone Uconnect™ Phone Tutorial To hear a brief tutorial of the system features, press the button and say “Uconnect™ Tutorial.” Voice Training For users experiencing difficulty with the system recog- nizing their voice commands or numbers, the Uconnect™ UNDERSTANDING THE FEATURES OF YOUR VEHICLE 107 Phone Voice Training feature may be used. To enter this training mode, follow one of the two following proce- dures: From outside the Uconnect™ Phone mode (e.g., from radio mode): • Press and hold the • Press the button and say the ⬙Setup, Voice button for five seconds until the session begins, or, Training⬙ command. Repeat the words and phrases when prompted by the Uconnect™ Phone. For best results, the Voice Training session should be completed when the vehicle is parked with the engine running, all windows closed, and the blower fan switched off. This procedure may be repeated with a new user. The system will adapt to the last trained voice only. 108 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To restore the Voice Command system to factory default settings, enter the Voice Training session via the above procedure and follow the prompts. Voice Command • For best performance, adjust the rearview mirror to provide at least 1⁄2 in (1 cm) gap between the overhead console (if equipped) and the mirror. • Always wait for the beep before speaking. • Speak normally, without pausing, just as you would speak to a person sitting a few feet/meters away from you. • Make sure that no one other than you is speaking during a Voice Command period. • Performance is maximized under: • low-to-medium blower setting, • low-to-medium vehicle speed, • low road noise, • smooth road surface, • fully closed windows, • dry weather condition. • Even though the system is designed for users speaking in North American English, French, and Spanish ac- cents, the system may not always work for some. • When navigating through an automated system such as voice mail, or when sending a page, at the end of speaking the digit string, make sure to say ⬙Send.⬙ • Storing names in the phonebook when the vehicle is • It is not recommended to store similar sounding not in motion is recommended. names in the Uconnect™ Phonebook. be spoken “eight-zero-zero” not “eight hundred”. • Phonebook (Downloaded and Uconnect™ Phone Lo- cal) name recognition rate is optimized when the entries are not similar. • Numbers must be spoken in single digits. “800” must • You can say ⬙O⬙ (letter ⬙O⬙) for ⬙0⬙ (zero). • Even though international dialing for most number combinations is supported, some shortcut dialing number combinations may not be supported. • In a convertible vehicle, system performance may be compromised with the convertible top down. Phone Far End Audio Performance • Audio quality is maximized under: • low-to-medium blower setting, • low-to-medium vehicle speed, UNDERSTANDING THE FEATURES OF YOUR VEHICLE 109 • low road noise, • smooth road surface, • fully closed windows, • dry weather conditions, and • operation from the driver’s seat. • Performance, such as audio clarity, echo, and loudness to a large degree rely on the phone and network, and not the Uconnect™ Phone. • Echo at the phone far end can sometimes be reduced • In a convertible vehicle, system performance may be by lowering the in-vehicle audio volume. compromised with the convertible top down. 110 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Bluetooth威 Communication Link Cellular phones have been found to lose connection to the Uconnect™ Phone. When this happens, the connec- tion can generally be reestablished by switching the phone off/on. Your cellular phone is recommended to remain in Bluetooth威 ON mode. Power-Up After switching the ignition key from OFF to either the ON or ACC position, or after a language change, you must wait at least five seconds prior to using the system. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 111 112 UNDERSTANDING THE FEATURES OF YOUR VEHICLE UNDERSTANDING THE FEATURES OF YOUR VEHICLE 113 114 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Voice Commands Alternate(s) Primary zero one two three four five six seven eight nine star (*) plus (+) pound (#) add location all Voice Commands Alternate(s) Primary call cancel confirmation prompts continue delete dial download edit emergency English erase all Espanol Francais help home Voice Commands Alternate(s) pairing phone book Primary language list names list phones mobile mute mute off new entry no pager pair a phone phone pairing phonebook previous record again redial UNDERSTANDING THE FEATURES OF YOUR VEHICLE 115 Voice Commands Alternate(s) return or main menu select phone settings or phone set up Primary return to main menu select phone send set up towing assistance transfer call Uconnect™ Tutorial try again voice training work yes 116 UNDERSTANDING THE FEATURES OF YOUR VEHICLE General Information This device complies with Part 15 of the FCC rules and RSS 210 of Industry Canada. Operation is subject to the following conditions: • Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. • This device may not cause harmful interference. • This device must accept any interference received, including interference that may cause undesired operation. VOICE COMMAND — IF EQUIPPED Voice Command System Operation This Voice Command system allows you to control your AM, FM radio, satellite radio, disc player, and a memo recorder. NOTE: Take care to speak into the Voice Interface System as calmly and normally as possible. The ability of the Voice Interface System to recognize user voice com- mands may be negatively affected by rapid speaking or a raised voice level. WARNING! Any voice commanded system should be used only in safe driving conditions following local laws and phone use. All attention should be kept on the roadway ahead. Failure to do so may result in an accident causing serious injury or death. button, you When you press the Voice Command will hear a beep. The beep is your signal to give a command. If you do not say a command within a few NOTE: seconds, the system will present you with a list of options. If you ever wish to interrupt the system while it lists button, listen options, press the Voice Command for the beep, and say your command. button while the Pressing the Voice Command system is speaking is known as “barging in.” The system will be interrupted, and after the beep, you can add or change commands. This will become helpful once you start to learn the options. NOTE: At any time, you can say the words “Cancel”, “Help” or “Main Menu”. These commands are universal and can be used from any menu. All other commands can be used depending upon the active application. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 117 For example, if you are in the disc menu and you are listening to FM radio, you can speak commands from the disc menu or from the FM radio menu. When using this system, you should speak clearly and at a normal speaking volume. The system will best recognize your speech if the win- dows are closed, and the heater/air conditioning fan is set to low. At any point, if the system does not recognize one of your commands, you will be prompted to repeat it. To hear the first available Menu, press the Voice button and say “Help” or “Main Command Menu”. 118 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Commands The Voice Command system understands two types of commands. Universal commands are available at all times. Local commands are available if the supported radio mode is active. Changing the Volume 1. Start a dialogue by pressing the Voice Command button. 2. Say a command (e.g., “Help”). 3. Use the ON/OFF VOLUME rotary knob to adjust the volume to a comfortable level while the Voice Command system is speaking. Please note the volume setting for Voice Command is different than the audio system. Main Menu Start a dialogue by pressing the Voice Command button. You may say “Main Menu” to switch to the main menu. In this mode, you can say the following commands: • “Radio” (to switch to the radio mode) • “Disc” (to switch to the disc mode) • “Memo” (to switch to the memo recorder) • “System Setup” (to switch to system setup) Radio AM (or Radio Long Wave or Radio Medium Wave — If Equipped) To switch to the AM band, say “AM” or “Radio AM”. In this mode, you may say the following commands: • “Frequency” (to change the frequency) • “Next Station” (to select the next station) • “Previous Station” (to select the previous station) • “Radio Menu” (to switch to the radio menu) • “Main Menu” (to switch to the main menu) Radio FM To switch to the FM band, say “FM” or “Radio FM”. In this mode, you may say the following commands: • “Frequency” (to change the frequency) • “Next Station” (to select the next station) • “Previous Station” (to select the previous station) • “Radio Menu” (to switch to the radio menu) • “Main Menu” (to switch to the main menu) Satellite Radio To switch to satellite radio mode, say “Sat” or “Satellite Radio”. In this mode, you may say the following com- mands: • “Channel Number” (to change the channel by its • “Next Channel” (to select the next channel) spoken number) UNDERSTANDING THE FEATURES OF YOUR VEHICLE 119 • “Previous Channel” (to select the previous channel) • “List Channel” (to hear a list of available channels) • “Select Name” (to say the name of a channel) • “Radio Menu” (to switch to the radio menu) • “Main Menu” (to switch to the main menu) Disc To switch to the disc mode, say “Disc”. In this mode, you may say the following commands: • “Track” (#) (to change the track) • “Next Track” (to play the next track) • “Previous Track” (to play the previous track) • “Main Menu” (to switch to the main menu) 120 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Memo To switch to the voice recorder mode, say “Memo”. In this mode, you may say the following commands: • “New Memo” (to record a new memo) — During the recording, you may press the Voice Command button to stop recording. You proceed by saying one of the following commands: − “Save” (to save the memo) − “Continue” (to continue recording) − “Delete” (to delete the recording) • “Play Memos” (to play previously recorded memos) — During the playback you may press the Voice button to stop playing memos. You Command proceed by saying one of the following commands: − “Repeat” (to repeat a memo) − “Next” (to play the next memo) − “Previous” (to play the previous memo) − “Delete” (to delete a memo) • “Delete All” (to delete all memos) System Setup To switch to system setup, say “Setup”. In this mode, you may say the following commands: • “Language German” • “Language Dutch” • “Language Italian” • “Language English” • “Language French” • “Language Spanish” • “Tutorial” • “Voice Training” UNDERSTANDING THE FEATURES OF YOUR VEHICLE 121 SEATS Seats are a primary part of the Occupant Restraint System of the vehicle. They need to be used properly for safe operation of the vehicle. WARNING! • DO NOT allow people to ride in any area of your vehicle that is not equipped with seats and seat belts. In a collision, people riding in these areas are more likely to be seriously injured or killed. • Be sure everyone in your vehicle is in a seat and using a seat belt properly. NOTE: Keep in mind that you have to press the Voice button first and wait for the beep Command before speaking the “Barge In” commands. Voice Training For users experiencing difficulty with the system recog- nizing their voice commands or numbers the Uconnect™ Voice “Voice Training” feature may be used. button, say “System 1. Press the Voice Command Setup” and once you are in that menu then say “Voice Training.” This will train your own voice to the system and will improve recognition. 2. Repeat the words and phrases when prompted by Uconnect™ Voice. For best results, the “Voice Training” session should be completed when the vehicle is parked, engine running, all windows closed, and the blower fan switched off. This procedure may be repeated with a new user. The system will adapt to the last trained voice only. 122 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Power Seats The power seat switch is on the outboard side of the seat near the floor. Use this switch to move the driver’s seat up or down, forward or rearward, or to recline the seatback. The passenger’s seat will move up or down, forward or rearward. WARNING! Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control. The seat belt might not be properly adjusted and you could be injured. Adjust the seat only while the vehicle is parked. CAUTION! DO NOT place any article under a power seat or impede its ability to move as it may cause damage to the seat controls. Seat travel may become limited if movement is stopped by an obstruction in the seat’s path. Power Seat Switch Power Reclining Seats The recliner control is located on the outboard side of the seat. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 123 WARNING! Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest. In a collision you could slide under the seat belt and be seriously or even fatally injured. Use the recliner only when the vehicle is parked. Power Seat Recline Switch 124 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Lumbar Support This feature allows you to increase or decrease the amount of lumbar support. Turn the control lever for- ward to increase and rearward to decrease the desired amount of lumbar support. Head Restraints Head restraints can reduce the risk of injury in the event of a rear impact. The head restraint should be adjusted so the top of the head restraint is located above the top of your ear. To raise the head restraint, pull upward on the head restraint. To lower the head restraint, press the large button, located on the base of the head restraint, and push downward on the head restraint. Lumbar Support Control Lever UNDERSTANDING THE FEATURES OF YOUR VEHICLE 125 Adjustable Head Restraint Removing Head Restraint To remove the head restraint, pull upward on the head restraint to its highest position, push in both buttons at the base of each head restraint rod, and simultaneously pull up on the head restraint. To install the head restraint, insert the head restraint rods into each guide, apply pressure down on the headrest until the head restraint reaches the first lock position, push the large button in and push down and adjust head restraint to desired position. 126 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: Ensure that the front of the head restraint is facing toward the front of the vehicle. WARNING! Driving a vehicle with the head restraints removed or improperly adjusted could cause serious injury or death in the event of a collision. The head restraints should always be checked prior to operating the vehicle and never adjusted while the vehicle is in motion. Always adjust the head restraints when the vehicle is in PARK. Heated Seats This feature heats the front driver, passenger, and second row seats. The controls for each heater are located near the bottom center of the instrument panel. After turning the ignition ON, you can choose from High, Low, or Off heat settings. Amber indicator lights in each switch indicate the level of heat in use. Two indicator lights will illuminate for High, one for Low and none for Off. Press the switch once to select High-level heat- ing. Press the switch a second time to select Low-level heating. Press the switch a third time to shut the heating elements Off. If High-level heating is selected, the system will auto- matically switch to the Low-level after 30 minutes of continuous operation. At that time, the number of indi- cators illuminated changes from two to one, indicating the change. Operation on the Low-level setting also turns off automatically after 30 minutes. NOTE: Once a heat setting is selected, heat will be felt within two to five minutes. WARNING! • Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, ex- haustion or other physical condition must exercise care when using the seat heater. It may cause burns even at low temperatures, especially if used for long periods of time. • Do not place anything on the seat that insulates against heat, such as a blanket or cushion. This may cause the seat heater to overheat. Sitting in a seat that has been overheated could cause serious burns due to the increased surface temperature of the seat. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 127 CAUTION! Repeated overheating of the seat could damage the heating element and/or degrade the material of the seat. Folding Rear Seat The rear seatbacks can be folded forward to provide an additional storage area. Pull on the loops shown in the illustration to fold down either or both seatbacks. These loops can be tucked away when not in use. 128 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Folding Rear Seats When the seatback is folded to the upright position, make sure it is latched by strongly pulling on the top of the seatback above the seat strap. WARNING! • Be certain that the seatback is securely locked into position. If the seatback is not securely locked into position, the seat will not provide the proper stability for child seats and/or passengers. An improperly latched seat could cause serious injury. • The cargo area in the rear of the vehicle (with the rear seatbacks in the locked-up or folded down position) should not be used as a play area by children when the vehicle is in motion. They could be seriously injured in an accident. Children should be seated and using the proper restraint system. TO OPEN AND CLOSE THE HOOD Two latches must be released to open the hood. 1. Pull the hood release lever located under the left side of the instrument panel. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 129 2. Move to the outside of the vehicle and push the safety catch to the left. The safety catch is located under the center front edge of the hood. Hood Release Lever Hood Safety Catch Use the hood prop rod (if equipped) to secure the hood in the open position. 130 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! To prevent possible damage, do not slam the hood to close it. Lower the hood, until it is open approxi- mately 6 in (15 cm), and then drop it. This should secure both latches. Never drive your vehicle unless the hood is fully closed, with both latches engaged. WARNING! Be sure the hood is fully latched before driving your vehicle. If the hood is not fully latched, it could open when the vehicle is in motion and block your vision. Failure to follow this warning could result in serious injury or death. LIGHTS Headlight Switch The headlight switch is located on the left side of the instrument panel. This switch controls the operation of the headlights, parking lights, instru- ment panel lights, instrument panel light dimming, inte- rior lights and fog lights. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 131 Automatic Headlights — If Equipped This system automatically turns the headlights on or off according to ambient light levels. To turn the system on, rotate the headlight switch counterclockwise to the A (AUTO) position. When the system is on, the headlight time delay feature is also on. This means the headlights will stay on for up to 90 seconds after you turn the ignition switch OFF. To turn the automatic system off, move the headlight switch out of the AUTO position. NOTE: The engine must be running before the head- lights will come on in the automatic mode. Headlights On with Wipers (Available with Automatic Headlights Only) When this feature is active, the headlights will turn on approximately 10 seconds after the wipers are turned on if the headlight switch is placed in the AUTO position. In addition, the headlights will turn off when the wipers are turned off if they were turned on by this feature. Headlight Switch Rotate the headlight switch clockwise to the first detent for parking light and instrument panel light operation. Rotate the headlight switch to the second detent for headlight, park light, and instrument panel light operation. 132 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The Headlights On with Wipers feature can be enabled or disabled. Refer to “Electronic Vehicle Information Center (EVIC)/Customer-Programmable Features” in “Under- standing Your Instrument Panel” for further information. Headlight Time Delay This feature provides the safety of headlight illumination for up to 90 seconds (programmable) when leaving your vehicle in an unlit area. To activate the delay feature, turn OFF the ignition switch while the headlights are still on. Then, turn off the headlights within 45 seconds. The delay interval begins when the headlight switch is turned off. If you turn the headlights, park lights, or ignition switch ON again, the system will cancel the delay. If you turn the headlights off before the ignition, they will turn off in the normal manner. Information Center NOTE: The lights must be turned off within 45 seconds of turning the ignition OFF to activate this feature. The Headlight delay time is programmable. Refer to “Electronic Vehicle (EVIC)/ Customer-Programmable Features” in “Understanding Your Instrument Panel” for further information. Daytime Running Lights — If Equipped The high beam headlights will come on as Daytime Running Lights whenever the ignition switch is ON, the headlights are off, and the parking brake is off. The headlight switch must be used for normal nighttime driving. Lights-On Reminder If the headlights or parking lights are on after the ignition is turned OFF, a chime will sound to alert the driver when the driver’s door is opened. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 133 Multifunction Lever The multifunction lever controls the operation of the turn signals, headlight beam selection, and passing lights. The multifunction lever is located on the left side of the steering column. Fog Lights The front fog light switch is built into the head- light switch. To activate the front fog lights, turn on the parking lights or the low beam headlights and press the headlight switch. To turn off the front fog lights, either press headlight switch again or turn off the headlight switch. An indicator light in the instrument cluster illuminates when the fog lights are turned on. NOTE: The fog lights will operate with the low beam headlights or parking lights on. However, selecting the high beam headlights will turn off the fog lights. Multifunction Lever 134 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Turn Signals Move the multifunction lever up or down and the arrows on each side of the instrument cluster flash to show proper operation of the front and rear turn signal lights. NOTE: • If either light remains on and does not flash, or there is a very fast flash rate, check for a defective outside light bulb. If an indicator fails to light when the lever is moved, it would suggest that the indicator bulb is defective. • A “Turn Signal On” message will appear in the Elec- tronic Vehicle Information Center (EVIC) and a con- tinuous chime will sound if the vehicle is driven more than 1 mi (1.6 km) with either turn signal on. Lane Change Assist Tap the lever up or down once, without moving beyond the detent, and the turn signal (right or left) will flash three times then automatically turn off. High/Low Beam Switch Push the multifunction lever away from you to switch the headlights to high beam. Pull the multifunction lever toward you to switch the headlights back to low beam. Flash-to-Pass You can signal another vehicle with your headlights by lightly pulling the multifunction lever toward you. This will cause the headlights to turn on at high beam and remain on until the multifunction lever is released. Overhead Console Map/Reading Lights These lights are mounted between the sun visors on the overhead console. Each light is turned on by pressing the lens. Press the lens a second time to turn off the light. These lights also turn on when a door is opened, or when the UNLOCK button on the Remote Keyless Entry (RKE) transmitter is pressed, or when the dimmer control is turned fully upward, past the second detent. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 135 because a door is open. This includes the glove box light, but not the trunk light. To restore interior light operation, either turn the ignition switch ON or cycle the light switch. Dimmer Control The dimmer control is part of the headlight switch and is located on the left side of the instrument panel. With the parking lights or headlights on, rotating the dimmer control upward will increase the brightness of the in- strument if equipped, the lighting in the door map pockets and cupholders. lights panel and, Overhead Console Interior Lights The interior lights come on when a door is opened. To protect the battery, the interior lights will turn off automatically 10 minutes after the ignition switch is moved to the LOCK position. This will occur if the interior lights were switched on manually or are on WINDSHIELD WIPERS AND WASHERS The multifunction lever operates the windshield wipers and washer when the ignition switch is in the ON position. The lever is located on the left side of the steering column. 136 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Dome Light Position Rotate the dimmer control completely upward to the second detent to turn on the interior lights. The interior lights will remain on when the dimmer control is in this position. Interior Light Defeat (OFF) Rotate the dimmer control to the extreme bottom OFF position. The interior lights will remain off when the doors are open. Parade Mode (Daytime Brightness Feature) Rotate the dimmer control upward to the first detent. This feature brightens all text displays such as the odometer, Electronic Vehicle Information Center (EVIC), and radio when the parking lights or headlights are on. Windshield Wiper/Washer Control Rotate the end of the multifunction lever to the first detent past the intermittent settings for low-speed wiper operation, or to the second detent past the intermittent settings for high-speed wiper operation. CAUTION! Turn the windshield wipers off when driving through an automatic car wash. Damage to the wind- shield wipers may result if the wiper switch is left in any position other than off. Intermittent Wiper System Use the intermittent wiper when weather conditions make a single wiping cycle with a variable pause be- tween cycles desirable. Rotate the end of the multifunc- tion lever to the first detent position, and then turn the end of the lever to select the desired delay interval. There are six delay settings, which allow you to regulate the UNDERSTANDING THE FEATURES OF YOUR VEHICLE 137 wipe interval from a minimum of one cycle every second to a maximum of approximately 23 seconds between cycles. Windshield Washers To use the washer, push the multifunction lever inward (toward the steering column) to the second detent and hold it for as long as washer spray is desired. If you activate the washer while the windshield wiper control is in the delay range, the wipers will operate for two or three wipe cycles after releasing the lever and then resume the intermittent interval previously selected. If you activate the washer while the windshield wiper is turned off, the wipers will operate for three wipe cycles and then turn off. 138 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Sudden loss of visibility through the windshield could lead to an accident. You might not see other vehicles or other obstacles. To avoid sudden icing of the windshield during freezing weather, warm the windshield with the defroster before and during windshield washer use. Mist Feature Push the multifunction lever inward (toward the steering column) to the first detent to activate a single wipe cycle to clear off road mist or spray from a passing vehicle. The wipers will continue to operate until you release the lever. Headlights On with Wipers (Available with Automatic Headlights Only) When this feature is active, the headlights will turn on approximately 10 seconds after the wipers are turned on if the headlight switch is placed in the AUTO position. In addition, the headlights will turn off when the wipers are turned off if they were turned on by this feature. The “Headlights On with Wipers” feature can be turned on or off through the Electronic Vehicle Information Center (EVIC) (if equipped). Refer to “Electronic Vehicle Information Center (EVIC)/Personal Settings (Customer- Programmable Features)” in “Understanding Your In- strument Panel” for further information. TILT/TELESCOPING STEERING COLUMN This feature allows you to tilt the steering column upward or downward. It also allows you to lengthen or shorten the steering column. The tilt/telescoping control handle is located below the steering wheel at the end of the steering column. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 139 To unlock the steering column, pull the control handle outward. To tilt the steering column, move the steering wheel upward or downward as desired. To lengthen or shorten the steering column, pull the steering wheel outward or push it inward as desired. To lock the steering column in position, push the control handle inward until fully engaged. WARNING! Do not adjust the steering column while driving. Adjusting the steering column while driving or driv- ing with the steering column unlocked, could cause the driver to lose control of the vehicle. Be sure the steering column is locked before driving your ve- hicle. Failure to follow this warning may result in serious injury or death. Tilt/Telescoping Control Handle 140 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ADJUSTABLE PEDALS — IF EQUIPPED The adjustable pedals system is designed to allow a greater range of driver comfort for steering wheel tilt and seat position. This feature allows both the brake and accelerator pedal to move toward or away from the driver to provide improved position with the steering wheel. The switch is located on the front side of the driver’s seat cushion side shield. Adjustable Pedals Switch Press the switch forward to move the pedals forward (toward the front of the vehicle). Press the switch rearward to move the pedals rearward (toward the driver). • The pedals can be adjusted with the ignition OFF. • The pedals can be adjusted while driving. • The pedals cannot be adjusted when the transmission is in REVERSE or when the Electronic Speed Control is on. CAUTION! Do not place any article under the adjustable pedals or impede its ability to move as it may cause damage to the pedal controls. Pedal travel may become lim- ited if movement is stopped by an obstruction in the adjustable pedal’s path. WARNING! Do not adjust the pedals while the vehicle is moving. You could lose control and have an accident. Always adjust the pedals while the vehicle is parked. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 141 ELECTRONIC SPEED CONTROL When engaged, Electronic Speed Control takes over the accelerator operation at speeds greater than 25 mph (40 km/h). The Electronic Speed Control lever, located on the right- side of the steering wheel, operates the system. Electronic Speed Control Lever 142 UNDERSTANDING THE FEATURES OF YOUR VEHICLE In order to ensure proper operation, the Elec- NOTE: tronic Speed Control System has been designed to shut down if multiple Speed Control functions are operated at the same time. If this occurs, the Electronic Speed Control System can be reactivated by pushing the Electronic Speed Control ON/OFF button and resetting the desired vehicle set speed. To Activate Push and release the ON/OFF button, located on the end of the Electronic Speed Control lever. The indicator light in the instrument cluster will illuminate to show that the speed control system is on. To turn the system off, push and release the ON/OFF button again. The system and the indicator light will turn off. WARNING! Leaving the Electronic Speed Control system on when not in use is dangerous. You could accidentally set the system or cause it to go faster than you want. You could lose control and have an accident. Always leave the Electronic Speed Control system off when you are not using it. To Set At A Desired Speed Turn the Electronic Speed Control ON. When the vehicle reaches the speed desired, push the lever downward to SET DECEL and release. Remove your foot from the accelerator pedal and the vehicle will operate at the selected speed. NOTE: • Electronic Speed Control will only function in 3rd, 4th, or 5th gear when in the Autostick威 mode (if equipped). • The Electronic Speed Control may not engage if a different size tire is installed on one wheel, such as the compact spare tire. To Deactivate The system will disable Electronic Speed Control without erasing the memory if you: • Softly tap the brake pedal. • Press the brake pedal. • Pull the Electronic Speed Control lever toward you (CANCEL). Pushing and releasing the ON/OFF button or turning the ignition OFF erases the set speed from memory. To Resume Speed If you deactivated the Electronic Speed Control without erasing the set speed from memory and your vehicle speed is above 20 mph (32 km/h) you can resume the UNDERSTANDING THE FEATURES OF YOUR VEHICLE 143 previous set speed. To do so, push the lever upward to RESUME ACCEL and release. Then remove your foot from the accelerator pedal. To Vary the Speed Setting When the Electronic Speed Control is set, you can in- crease speed by pushing up and holding the RESUME ACCEL lever. If the lever is continually held in the RESUME ACCEL position, the set speed will continue to increase until the lever is released, then the new set speed will be established. Tapping the Electronic Speed Control lever to RESUME ACCEL once will result in a 1 mph (1.6 km/h) speed increase. Each time the lever is tapped speed increases, so tapping the lever three times will increase speed by 3 mph (4.8 km/h), etc. 144 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To decrease speed while Electronic Speed Control is set, push down and hold the Electronic Speed Control lever in SET DECEL. Release the Electronic Speed Control lever when the desired speed is reached, and a new set speed will be established. Tapping the Electronic Speed Control lever to SET DE- CEL once will result in a 1 mph (1.6 km/h) speed decrease. Each time the lever is tapped, speed decreases. To Accelerate For Passing Press the accelerator as you would normally. When the pedal is released, the vehicle will return to the set speed. Using Electronic Speed Control on Hills NOTE: The Electronic Speed Control system maintains speed up and down hills. A slight speed change on moderate hills is normal. The automatic transmission will downshift while climb- ing uphill or descending downhill. This downshift is necessary to maintain vehicle set speed. On steep hills, a greater speed loss or gain may occur, so it may be preferable to drive without Electronic Speed Control. WARNING! Electronic Speed Control can be dangerous where the system cannot maintain a constant speed. Your ve- hicle could go too fast for the conditions and you could lose control. An accident could be the result. Do not use Electronic Speed Control in heavy traffic or on roads that are winding, icy, snow-covered or slippery. OVERHEAD CONSOLE The overhead console contains courtesy/reading lights and storage for sunglasses. Universal Garage Door Opener (HomeLink威) buttons and power sunroof switch may also be included, if equipped. Overhead Console UNDERSTANDING THE FEATURES OF YOUR VEHICLE 145 Courtesy/Reading Lights At the forward end of the console are two courtesy/ reading lights. Press the lens to turn on the light. Press it a second time to turn off the light. These lights also turn on when a door is opened, when the UNLOCK button on the Remote Keyless Entry (RKE) transmitter is pressed, or when the dimmer control is turned fully upward, past the second detent. Sunglasses Storage At the rear of the console, a compartment is provided for the storage of a pair of sunglasses. The storage compartment access is a ⬙push/push⬙ design. Push on the raised bar on the compartment door to open. Push on the raised bar to close. 146 UNDERSTANDING THE FEATURES OF YOUR VEHICLE GARAGE DOOR OPENER — IF EQUIPPED HomeLink威 replaces up to three remote controls (hand- held transmitters) that operate devices such as garage door openers, motorized gates, lighting or home security systems. The HomeLink威 unit operates off your vehicle’s battery. The HomeLink威 buttons are located in the overhead console, and contain one, two or three dots/lines desig- nating the different HomeLink威 channels. HomeLink威 Buttons NOTE: HomeLink威 is disabled when the Vehicle Secu- rity Alarm is active. WARNING! • Your motorized door or gate will open and close while you are training the Universal Transceiver. Do not train the transceiver if people, pets, or other objects are in the path of the door or gate. Only use this transceiver with a garage door opener that has a “stop and reverse” feature as required by federal safety standards. This includes most garage door opener models manufactured after 1982. Do not use a garage door opener with- out these safety features. Call toll-free 1–800–355– 3515 or, on the Internet at www.HomeLink.com for safety information or assistance. • Vehicle exhaust contains carbon monoxide, a dan- gerous gas. Do not run your vehicle in the garage while training the transceiver. Exhaust gas can cause serious injury or death. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 147 Programming HomeLink姞 Before You Begin If you have not trained any of the HomeLink威 buttons, erase all channels before you begin training. To do this, press and hold the two outside buttons for up to 20 seconds. The EVIC will display “CLEARING CHANNELS.” Release the buttons when the EVIC mes- sage states “CHANNELS CLEARED.” It is recommended that a new battery be placed in the handheld transmitter of the device that is being copied to HomeLink威 for more efficient training and accurate transmission of the radio-frequency signal. Your vehicle should be parked outside of the garage while training. 1. Place the ignition in the RUN position. 148 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 2. Place the handheld transmitter 1 to 3 in (3 to 8 cm) from the HomeLink威 buttons while keeping the EVIC display in view. For optimal training, point the battery end of the hand- held transmitter away from the HomeLink威. 3. Simultaneously, press and hold both the chosen HomeLink威 button and the handheld transmitter button until the EVIC display changes from “CHANNEL # TRAINING” to “CHANNEL # TRAINED.” Then release both the HomeLink威 and handheld trans- mitter buttons. If the EVIC display states “DID NOT TRAIN” repeat Step 3. If the signal is too weak, replace the battery in the handheld transmitter. It may take up to 30 seconds or longer in rare cases. The garage door may open and close while you train. NOTE: Some gate operators and garage door openers may require you to replace Step 3 with procedures noted in the “Gate Operator/Canadian Programming” section. 4. Press and hold the just-trained HomeLink威 button. If the channel has been trained, the EVIC display will now state “CHANNEL # TRANSMIT.” If the EVIC display still states “CHANNEL # TRAIN- ING” repeat Step 3. NOTE: After training a HomeLink威 channel, if the garage door does not operate with HomeLink威 and the garage door opener was manufactured after 1995, the garage door opener may have rolling code. If so, proceed to the heading “Programming A Rolling Code System.” 5. PROGRAMMING A ROLLING CODE SYSTEM At the garage door opener motor (in the garage), locate the “Learn” or “Training” button. This can usually be found where the hanging antenna wire is attached to the garage door opener motor (it is NOT the button normally used to open and close the door). 1 — Garage Door Opener 2 — Training Button UNDERSTANDING THE FEATURES OF YOUR VEHICLE 149 6. Firmly press and release the LEARN or TRAINING button. The name and color of the button may vary by manufacturer. NOTE: You have 30 seconds in which to initiate the next step after the LEARN button has been pressed. 7. Return to the vehicle and press the programmed HomeLink威 button twice (holding the button for two

Boost Classifieds - Car Advice, Reviews, Events & Classifieds

2010 Dodge Charger SRT8 Owners Manual