2009 Chrysler TOWN and Country Owners Manual

your own voice to the system and will improve recogni- tion. 2. Repeat the words and phrases when prompted by uconnect威 phone. For best results, the Voice Training session should be completed when the vehicle is parked, engine running, all windows closed, and the blower fan

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 149
switched off. This procedure may be repeated with a new user. The system will adapt to the last trained voice only.

SEATS Seats are a primary part of the Occupant Restraint System of the vehicle. They need to be used properly for safe operation of the vehicle.

WARNING!

• DO NOT allow people to ride in any area of your vehicle that is not equipped with seats and seat belts. In a collision, people riding in these areas are more likely to be seriously injured or killed. • Be sure everyone in your vehicle is in a seat and

using a seat belt properly.

150 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Manual Front And Second Row Seat Adjuster The adjusting bar is located under the front of the seat. Pull the bar upward and move the seat to the desired position. Release the bar to lock the seat into position.

Using body pressure, move forward and rearward on the seat to be sure the seat adjusters have latched.

WARNING!

Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control. The seat belt might not be properly adjusted and you could be injured. Adjust any seat only while the vehicle is parked.

Manual Seat Adjuster

Eight–Way Driver And Passenger Power Seat — If Equipped The power seat switches are located on the outboard side of the seat. The front switch controls the up/down, forward/rearward and tilt adjustment. The rear switch controls the recline adjustment of the seatback.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 151

Driver Power Seat Switch

1 — Front Switch

2 — Rear Switch

152 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

CAUTION!

DO NOT place any article under a power seat or impede its ability to move as it may cause damage to the seat controls. Seat travel may become limited if movement is stopped by an obstruction in the seat’s path.

Adjustable Head Restraints Head restraints can reduce the risk of whiplash injury in the event of a rear impact. Pull upward or push down- ward on the head restraint cushion so that the upper edge is as high as practical. To raise the head restraint, pull upward on the head restraint. To lower the head restraint, press the release tab located at the base of the head restraint and push downward on the head restraint.

Adjusting The Head Restraint Cushion

Heated Seats — If Equipped This feature heats the front driver and passenger seats. The controls for front heated seats are located on the center instrument panel area.

After turning the ignition ON, you can choose from High, Low, or Off heat settings. Amber indicator lights in each switch indicate the level of heat in use. Two indicator lights will illuminate for High, one for Low, and none for Off.

Press the switch once to select High-level heat- ing. Press the switch a second time to select Low-level heating. Press the switch a third time to shut the heating elements Off.

Second row heated seat switches are located in the sliding side door handle trim panels and function the same as front switches.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 153

Heated Seat Switch

154 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

WARNING!

Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, exhaus- tion or other physical condition must exercise care when using the seat heater. It may cause burns even at low temperatures, especially if used for long periods of time. DO NOT place anything on the seat that insulates against heat, such as a blanket or cushion. This may cause the seat heater to overheat.

Manual Reclining Seats — If Equipped The recliner control lever is on the outboard side of the seat. To recline, lean forward slightly, lift the lever, then push back to the desired position and release the lever. Lean forward and lift the lever to return the seatback to

its normal position. Using body pressure, lean forward and rearward on the seat to be sure the seatback has latched.

Manual Reclining Seat Control

WARNING!

DO NOT ride with the seatback reclined so that the shoulder belt is no longer resting against your chest. In a collision you could slide under the seat belt and be seriously or fatally injured. Use the recliner only when the vehicle is parked.

Manual Lumbar Adjust Lever — If Equipped The lumbar adjustment lever is located on the outboard side of the seat. To increase the support, rotate the lever downward. To decrease the support, rotate the handle upward.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 155

Manual Lumbar Lever Stow ’n Go姞 Seating — If Equipped On vehicles equipped with Stow ’n Go威 seating, the second and third row seats may be folded into the floor for convenient storage.

156 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Fold Second Row Seats 1. Move the front seat fully forward. 2. Lower the head restraints and raise the armrests on the second row seat. 3. Slide the storage bin locking mechanism to the ⬙LOCK⬙ position and then pull up on the storage bin latch to open the cover.

Storage Bin Cover Lock Release

4. Pull up on the seatback recliner lever located on the outboard side of the seat and fold the seatback down. To assure the seatback is latched in the folded position, additional downward pressure on the seatback may be required when folding.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 157

Second Row Seatback Release Lever

5. Pull rearward on the release strap located at the rear of the seat and tumble the seat forward into the storage bin.

Second Row Seat Release Strap

6. Close the storage bin cover.

158 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

CAUTION!

2. Pull up on the handle to lift the seat out of the storage bin and push the seat rearward to latch the seat anchors.

The storage bin cover must be locked and flat to avoid damage from contact with the front seat tracks, which have minimal clearance to the cover.

WARNING!

In an accident, serious injury could result if the seat storage bin covers are not properly latched. • DO NOT drive the vehicle with the storage bin • Keep the storage bin covers closed and latched • DO NOT use a storage bin latch as a tie down.

while the vehicle is in motion.

covers open.

To Unfold Second Row Seats 1. Pull up on the storage bin latch to open the cover.

Second Row Seat Release Handle

3. Pull upward on the seatback recliner lever, located on the outboard side of the seat, to return the seatback to its full upright position.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 159
To tilt the seat, pull forward on the release strap located on the front of the seat between the seatback and seat cushion and tilt the seat fully forward. To return the seat to its upright position, push rearward on the seatback until it latches. Always ensure that it is fully latched.

Second Row Seatback Release Lever

4. Adjust the head restraint to the desired position, close the storage bin cover and slide the storage bin locking mechanism to the ⬙Unlocked⬙ position. Easy Access Seating The second row Stow ’n Go威 seats can be tilted forward for easy access to the third row seat or rear cargo area.

Tilting Second Row Stow ’n Go威 Seat

160 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

WARNING!

In the event of a collision you could be injured if the seat is not fully latched.

• Seats are removable

Swivel ’n Go姞 Premium Seating — If Equipped Premium second row Swivel ’n Go威 Seating features include: • A table that installs between the second and third row seats. The table disassembles and stows in the hidden second row floor storage bin

• Seats rotate to face forward or rearward • Seat belts are integrated into the swivel seats • Dual folding armrests • A side storage pocket that will accommodate a phone

or handheld game

Swivel ’n Go威 Seating Features

1 — Moveable Armrest 2 — Seatback Release 3 — Swivel Release

4 — Fore-Aft Adjustment 5 — Seat Release

WARNING!

When the seatback release handle is lifted, the seat- back will rotate forward. To avoid injury, if you are not seated in the seat, stay clear from the area in the path of the rotating seatback.

To swivel the seat: Pull the lower handle on the outboard side of the seat and push the side of the seatback to begin rotation. Once the seat begins to rotate, the handle may be released. The seat locks in position once reaching the forward or rearward positions only.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 161

Swivel Release

Seatbacks fold forward on an angle, not flat. This allows the seats to swivel when the seatbacks are folded.

Removing Swivel ’n Go威 Premium Seating — If Equipped 1. Remove any obstructions from the floor behind the seat, and stow the third row seat. 2. Pull up on the release bar located at the bottom front edge of the swivel seat.

162 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

WARNING!

Failure to comply with the following conditions could result in serious injury or even death: • NEVER place any child seat or infant carrier in the Swivel ’n Go威 seat while it is in the rearward facing position. • The swivel seat should be locked in the forward position when using any child seat or infant carriers, with the vehicle in motion. • Occupants riding in Swivel ’n Go威 seating must be wearing their seat belt and the seat must be locked in either the forward-facing or rearward- facing position. • Make sure the Swivel ’n Go威 seat is in a locked position with the release handle fully engaged. Test the seat after it is locked to see that it doesn’t swivel.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 163
5. Lower the release handle located at the bottom front edge of the seat. Each seat weighs about 90 lbs (81 kg). NOTE: Electrical contacts for the available heated seats automatically disengage or engage as the seat is removed or installed. The contacts slide past each other as the seat is rolled to and from the strikers. When reinstalling the seat, make certain to lower the release handle to ensure the seat is latched securely.

WARNING!

In a collision, you or others in your vehicle could be injured if seats are not properly latched to their floor attachments. Always be sure the seats are fully latched.

Release Bar

3. From behind the seat, lift up on the rear of the seat cushion while pulling the seat in a rearward direction. 4. Remove the seat from vehicle through the liftgate. Rollers are part of the seat frame and will ease the removal process.

164 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Swivel ’n Go威 Premium Seating Table — If Equipped The Swivel ’n Go威 Seating Table consists of an easily assembled post and top.

1. Open the floor storage cover in front of the second row seats.

Second Row Seating and Table

The table and leg are stored beneath the floor when not in use. To install the table follow these steps:

Table and Leg Storage

2. Remove the pole and table top by loosening the hook and loop straps. 3. Swivel the second row seats so they are facing the rear.

4. Insert pole into base by aligning the lock button into notch of the base.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 165
NOTE: You will hear an audible “click” when the lock button engages the base. 6. Place the table top over the installed pole aligning with the mating feature of the underside of the table top. Apply pressure on the table top and press downward. NOTE: You will hear an audible “click” when the table latch engages the pole.

WARNING!

Installing Table Leg Into Base

1 — Table Base 5. Twist the pole in a clockwise rotation until it stops.

2 — Lock/Release Button

Failure to comply with the following conditions could result in serious injury or even death: • DO NOT install the table while vehicle is in • NEVER drive the vehicle with only the pole in- • DO NOT place heavy or sharp objects on table.

motion.

stalled.

(Continued)

166 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

WARNING! (Continued)

• DO NOT place liquid drinks on the table, use • Second row seats must be locked in the rearward

available cupholders.

facing position before installing the table.

To separate the table top from the pole, follow these steps: 1. Locate the release latch on the underside of the table top.

Table Top Release

2. Pull horizontally on the latch to activate the release from the pole. 3. While pulling on the latch, pull upward to remove the table top from the pole.

NOTE: The table top should be removed from the leg prior to removing the leg from its mounting base. 4. Locate the release button on the pole. Press the release button firmly to activate the release from the base. 5. While pressing the release button, twist the pole in a counterclockwise rotation until it stops. Pull upward to remove the pole from the base. 6. Place the pole on the underside of the table top and secure with the hook and loop straps. 7. Once the pole and table top are secured, you may place them in the floor storage bin in front of the second row seats. NOTE: Always store the table and pole in the floor storage bin when not in use.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 167

Plastic Grocery Bag Retainer Hooks Retainer hooks which will hold plastic grocery bag handles are built into the seatbacks of all rear seats and some front seats. The floor supports the partial weight of the bagged goods. Second Row Bench Seat — If Equipped While the bench seat does not stow in the floor, it is removable for added cargo space. Release levers are located on the rear leg assemblies, near the floor. To remove the seat, squeeze each release handle and rotate downwards to deploy the wheels. A lock indicator button pops up when the seat is unlocked. The seat assembly can now be removed from the vehicle and moved on its Easy Out威 Rollers.

168 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

WARNING!

If not properly latched, the bench seats could become loose. Personal injuries could result. After reinstall- ing these seats, be sure the red indicator button on the release handles return into the handles.

Release Handles

To reinstall the seat, align the seat into the detent posi- tions on the floor. Squeeze the release handle and rotate upward until the lock indicator button returns into the handle.

Third Row Power Seat — If Equipped The third row power seat offers the following features: • The seatbacks can be folded forward for additional • Head restraints can be stowed with the seat. • Tailgate mode flips the seat rearward to face out the

cargo space if needed.

tailgate.

The power recline feature, located on the side of the seat cushion, adjusts the seatback angle forward/rearward for occupant comfort.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 169
The switch is only functional when the liftgate is open and the vehicle is in PARK.

Third Row Power Seat Switch

Third Row Power Seat Switch — If Equipped A one-touch power folding seat switch is located in the left rear trim panel as part of a switch bank.

One Touch Folding Seat Third Row

The rear switch bank allows multiple power folding and unfolding positions for the third row seats.

170 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Left and right third row seats can be folded individually or together. The third row power folding seat adjusts to the following positions using the switch bank located on the left rear trim panel:

NOTE: The third row power seat system includes obstacle detection for safe operation. When the system detects an obstacle, the motors will stop and reverse the motion a short distance to move the seat away from the obstacle. Should this occur, remove the obstacle and press the button again, for the desired position. To Fold Third Row Seats Manually — If Equipped 1. Lower the head restraint to its full down position. 2. Pull release strap marked “1” located on the rear of the seat to lower the seatback. 3. Pull release strap marked “2” to release the anchors.

Rear Panel Power Switch Bank

1 — Open to Normal 2 — Stow 3 — Tailgate

4 — Fold Flat 5 — Right/Left Seats 5 — Both Seats

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 171

To Unfold Third Row Seats 1. Pull up on the assist strap to lift the seat out of the storage bin and push the seat forward until the anchors latch. 2. Pull release strap marked “1” to unlock the recliner. 3. Pulling strap “3” releases the seatback to return to its full upright position. 4. Adjust the head restraint to the desired position.

WARNING!

In a collision, you or others in your vehicle could be injured if seats are not properly latched to their floor attachments. Always be sure the seats are fully latched.

Folding Third Row Seat Strap

4. Pull release strap marked “3” and tumble the seat rearward into the storage bin.

172 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Tailgate Mode 1. Pull release strap “2”, then pull release strap “3” to rotate the entire seat rearward.

Tailgate Positioning Release Straps 2 and 3

2. To restore the seat to its upright position, lift up on the seatback and push forward until the anchors latch.

WARNING!

To avoid serious injury or death, NEVER operate the vehicle with occupants in the third row seat while in the tailgate mode.

DRIVER MEMORY SEAT — IF EQUIPPED The Memory Buttons 1 and 2 on the driver’s door panel can be programmed to recall the driver’s seat, driver’s outside mirror, adjustable brake and accelerator pedals, and radio station preset settings. Your Remote Keyless Entry (RKE) transmitters can also be programmed to recall the same positions when the UNLOCK button is pressed.

3

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 173

Setting Memory Positions and Linking RKE Transmitter to Memory

NOTE: Each time the SET (S) button and a numbered button (1 or 2) is pressed, you erase the memory settings for that button and store a new one. 1. Insert the ignition key and turn the ignition switch to the ON position. 2. Press the driver door MEMORY button number 1 if you are setting the memory for driver 1, or button number 2 if you are setting the memory for driver 2. The system will recall any stored settings. Wait for the system to complete the memory recall before continuing to Step 3. 3. Adjust the driver’s seat, recliner, and driver’s side- view mirror to the desired positions. 4. Adjust the brake and accelerator pedals to the desired positions.

Driver Memory Switch

Your vehicle may have been delivered with two RKE transmitters. Only one RKE transmitter can be linked to each of the memory positions.

174 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 5. Turn on the radio and set the radio station presets (up to 10 AM and 10 FM stations can be set). 6. Turn the ignition switch to the OFF position and remove the key. 7. Press and release the SET (S) button located on the driver’s door. 8. Within five seconds, press and release MEMORY button 1 or 2 on the driver’s door. The next step must be performed within 10 seconds if you desire to also use a RKE transmitter to recall memory positions. 9. Press and release the LOCK button on one of the RKE transmitters. 10. Insert the ignition key and turn the ignition switch to the ON position. 11. Select ⬙Remote Linked to Memory⬙ in the Electronic Vehicle Information Center (EVIC) and enter “Yes”. Refer

to the “Customer-Programmable Features” in the “Elec- tronic Vehicle Information Center (EVIC)” section for more information. 12. Repeat the above steps to set the next Memory position using the other numbered Memory button or to link another RKE transmitter to memory. Memory Position Recall NOTE: The vehicle must be in PARK to recall memory positions. If a recall is attempted when the vehicle is not in PARK, a message will be displayed in the EVIC. To recall the memory settings for driver one, press MEMORY button 1 on the driver’s door or the UNLOCK button on the RKE transmitter linked to memory position 1.

To recall the memory setting for driver two, press MEMORY button 2 on the driver’s door or the UNLOCK button on the RKE transmitter linked to Memory Position 2. A recall can be cancelled by pressing any of the MEMORY buttons on the driver’s door during a recall (S, 1, or 2). When a recall is cancelled, the driver’s seat, driver’s mirror, and the pedals stop moving. A delay of one second will occur before another recall can be selected. To Disable RKE Transmitter Linked to Memory 1. Turn the ignition switch to the OFF position and remove the key. 2. Press and release MEMORY button 1. The system will recall any memory settings stored in position 1. Wait for the system to complete the memory recall before continu- ing to Step 3.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 175
3. Press and release the memory SET (S) button located on the driver’s door. A chime will sound signaling that you are in the memory set mode. 4. Within five seconds, press and release MEMORY button 1 on the driver’s door. A chime will sound signaling to you that the driver memory has been set. 5. Within five seconds, press and release the UNLOCK button on the RKE transmitter. A chime will sound signaling to you that the RKE transmitter link has been successfully disabled. To disable another RKE transmitter linked to either Memory Position, repeat Steps 1 to 5 for each RKE transmitter. NOTE: Once programmed, all RKE transmitters linked to memory can be easily enabled or disabled at one time.

176 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Refer to the Remote Linked to Memory ⬙Customer- Programmable Features⬙ in the Electronic Vehicle Infor- mation Center (EVIC) for more information. Easy Entry/Exit Seat (Available with Memory Seat ONLY) This feature provides automatic driver seat positioning to enhance driver mobility when entering and exiting the vehicle. The distance the driver seat moves depends on where you have the driver seat positioned when you remove the key from the ignition switch. • When you remove the key from the ignition switch, the driver seat will move about 2.4 in (60 mm) rearward if the driver seat position is greater than or equal to 2.7 in (67.7 mm) forward of the rear stop. The seat will return to its previously set position when you insert the key into the ignition switch and turn it out of the LOCK position.

• When you remove the key from the ignition switch the driver seat will move to a position 0.3 in (7.7 mm) forward of the rear stop if the driver seat position is between 0.9 – 2.7 in (22.7 – 67.7 mm) forward of the rear stop. The seat will return to its previously set position when you insert the key into the ignition switch and turn it out of the LOCK position. • The Easy Entry/Easy Exit feature is disabled when the driver seat position is less than 0.9 in (22.7 mm) forward of the rear stop. At this position, there is no benefit to the driver by moving the seat for Easy Exit or Easy Entry.

Each stored memory setting will have an associated Easy Entry and Easy Exit Position.

NOTE: The Easy Entry/Easy Exit feature can be en- abled or disabled through the programmable features in the Electronic Vehicle Information Center (EVIC). If your vehicle is not equipped with an EVIC, your dealership can activate/deactivate this feature for you. For details, refer to “Automatically Move Seat Back on Exit,” section of this manual.

TO OPEN AND CLOSE THE HOOD To open the hood, two latches must be released. 1. Pull the hood release lever located on the instrument panel, below the steering column.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 177

Hood Release

2. Move to the front of the vehicle and look inside the center of the hood opening. Locate, then push the safety catch lever to the right, while raising the hood at the same time.

178 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Safety Catch Location

Use the hood prop rod to secure the hood in the open position.

CAUTION!

To prevent possible damage, do not slam the hood to close it. Lower the hood until it is open approxi- mately 12 in (30 cm) and then drop it. This should secure both latches. Never drive your vehicle unless the hood is fully closed, with both latches engaged.

WARNING!

If the hood is not fully latched, it could fly up when the vehicle is moving and block your forward vision. You could have a collision. Be sure all hood latches are fully latched before driving.

LIGHTS All of the lights, except the Hazard Warning lights, headlight high beams and flash-to-pass, are controlled by switches to the left of the steering column on the instru- ment panel.

Headlight Switch With Halo Control Assembly

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 179

Interior Lighting Interior lights are turned on when a door or liftgate is opened, the Remote Keyless Entry (RKE) transmitter is activated, or when the dimmer control is moved to the extreme top. The interior lights will automatically turn off in approxi- mately 10 minutes for the first activation and 90 seconds every activation thereafter until the engine is started, if one of the following occur: • A door, sliding door or the liftgate is left open • Any overhead reading light is left on NOTE: The key must be out of the ignition switch or the ignition switch must be in the OFF position for this feature to operate.

180 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Dome Light Positions

Rotate the dimmer control completely upward to the second detent (extreme top position) to turn on the interior lights. The interior lights will remain on when the dimmer control is in this position.

Parade Mode (Daytime Brightness Feature)

feature brightens

Rotate the dimmer control to the first detent. This the odometer, radio and overhead dis- plays when the parking lights or head- lights are on.

Interior Lighting Defeat (Off)

Rotate the dimmer control to the off position (extreme bottom). The inte- rior lights will remain off when the doors or liftgate are open.

Dimmer Control

With the parking lights or headlights on, rotating the dimmer control for the interior lights on the instrument panel upward will increase the brightness of the instrument panel lights.

Halo Lights — If Equipped Halo lights are strategically placed soft lighting that help to illuminate specific areas to aid the occupants in locating specific features while driving at night.

To activate the Halo lights, push in the Halo switch control knob. Pressing the switch con- trol knob in a second time will turn the Halo lights off.

Parking Lights

Turn the headlight switch knob to the first detent to turn the parking lights on. This also turns on all

instrument panel lighting. Headlights

Turn the headlight switch knob to the second detent to turn the headlights and parking lights on. This also turns on all instrument panel lighting.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 181
To change the brightness of the instrument panel lights, rotate the dimmer control up or down. Automatic Headlights — If Equipped This system automatically turns your headlights on or off based on ambient light levels. To turn the system on, turn the headlight switch to the extreme counterclockwise position aligning the indicator with the “A” on the headlight switch. When the system is on, the Headlight Time Delay feature is also on. This means your headlights will stay on for up to 90 seconds after you turn the ignition switch OFF. To turn the Automatic System off, turn the headlight switch clockwise to the “O” off position.

182 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Automatic Headlights

NOTE: The engine must be running before the head- lights will come on in the Automatic mode. Headlights On With Wipers — If Equipped When your headlights are in the Automatic mode and the engine is running, the headlights will automatically turn on when the wiper system is also turned on. Headlights

on when windshield wipers are on may be found on vehicles equipped with an automatic headlight system. Refer to the Electronic Vehicle Information Center (EVIC) in Section 4 under “Personal Settings (Customer- Programmable Features)” for more information. Headlight Delay — If Equipped This feature provides the safety of headlight illumination for up to 90 seconds after exiting your vehicle. To activate the delay feature, turn OFF the ignition switch while the headlights are still on. Then turn off the headlights within 45 seconds. The 90 second delay inter- val begins when headlight switch is turned off. If the headlights or parking lights are turned back on or the ignition switch is turned ON, the delay will be cancelled. When exiting the vehicle the driver can choose to have the headlights remain on for 30, 60, or 90 seconds or not remain on. To change the timer setting, see your autho- rized dealer.

“Personal Settings

The headlight delay time is programmable on vehicles equipped with an EVIC. Refer to “Delay Turning Head- lights Off,” under (Customer- Programmable Features)” under “Electronic Vehicle In- formation Center (EVIC)” in Section 4. If the headlights are turned off before the ignition, they will turn off in the normal manner. NOTE: The headlights must be turned off within 45 sec- onds of turning the ignition OFF to activate this feature. Lights-On Reminder If the headlights or the parking lights are left on, or if the dimmer control is in the extreme top position after the ignition switch is turned OFF, a chime will sound when the driver’s door is opened.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 183

Daytime Running Lights (Canada/Fleet Vehicles Only) The headlights on your vehicle will illuminate when the engine is started and the transmission is in any gear except PARK. This provides a constant lights on condi- tion until the ignition is turned OFF. The lights illuminate at less than 50% of normal intensity. If the parking brake is applied, the Daytime Running Lights (DRL) will turn off. Also, if a turn signal is activated, the DRL lamp on the same side of the vehicle will turn off for the duration of the turn signal activation. Once the turn signal is no longer active, the DRL lamp will illuminate. Front Fog Lights — If Equipped

To activate the front fog lights, turn on the parking lights or the low beam headlights and push in the headlight switch control knob. Pressing the head- light switch control knob in a second time will turn the front fog lights off.

184 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Battery Protection This feature provides battery protection to avoid wearing down the battery if the headlights, parking lights, or front fog lights are left on for extended periods of time when the ignition switch is in the LOCK position. After eight minutes of the ignition switch being in the LOCK position and the headlight switch in any position other than OFF or AUTO, the lights will turn off automatically until the next cycle of the ignition switch or headlight switch. The battery protection feature will be disabled if the ignition switch is turned to any other position other than LOCK during the three minute delay.

Multifunction Lever The multifunction lever is located on the left side of the steering column. The multifunction lever controls the: • Turn Signals • Headlight Beams Low/High • Flash-To-Pass (Optical Horn) • Front and Rear Wipers — Washer Functions Turn Signals Move the multifunction lever up or down and the arrows on each side of the instrument cluster flash to show proper operation of the front and rear turn signal lights.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 185

Lane Change Assist Tap the lever up or down once, without moving beyond the detent, and the turn signal (right or left) will flash three times then automatically turn off. Turn Signal Warning If the vehicle electronics sense that the vehicle has traveled at over 18 mph (29 km/h) for approximately 1 mile (1.6 km) with the turn signals on, a chime will sound to alert the driver. High Beam/Low Beam Select Switch When the headlights are turned on, pushing the multi- function lever toward the instrument panel will switch from low beams to high beams. Pulling back to the neutral position returns the headlights to the low beam operation.

Turn Signals

If either light remains on and does not flash, or NOTE: there is a very fast flash rate, check for a defective outside light bulb. If an indicator fails to light when the lever is moved, the indicator bulb is defective.

it would suggest

that

186 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Flash-To-Pass You can signal another vehicle with your headlights by lightly pulling the multifunction lever toward you. This will turn on the high beam headlights until the lever is released. SmartBeams — If Equipped The SmartBeam system provides increased forward light- ing at night by automating high beam control through the use of a digital camera mounted on the inside rearview mirror. This camera detects vehicle specific light and automatically switches from high beams to low beams until the approaching vehicle is out of view. To Activate 1. Select “Automatic High Beams — ON” through the EVIC. Refer to “Automatic High Beams,” “Personal Settings (Customer- Programmable Features)” under “Electronic Vehicle Information Center” in Section 4.

2. Rotate the headlight switch counterclockwise to the AUTO (A) position. 3. Push the multifunction lever away from you to switch the headlights to the high beam position. Refer to “Mul- tifunction Lever” in this section. NOTE: This system will not activate until the vehicle is at, or above, 25 mph (40 km/h). To Deactivate Perform either of the following steps to deactivate the SmartBeam system. 1. Pull the multifunction lever toward you to switch the headlights from the high beam to the low beam position. 2. Rotate the headlight switch clockwise from the AUTO (A) to the on position. NOTE: Broken, muddy or obstructed headlights and taillights of vehicles in the field of view will cause

headlights to remain on longer (closer to the vehicle). Also, dirt, film and other obstructions on the windshield or camera lens will cause the system to function improperly.

WINDSHIELD WIPERS AND WASHERS The wipers and washers are operated by a switch within the multifunction lever. Rotate the end of the multifunc- tion lever to select the desired wiper speed. NOTE: Always remove any buildup of snow that pre- vents the windshield wiper blades from returning to the off position. If the windshield wiper switch is turned off and the blades cannot return to the off position, damage to the wiper motor may occur.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 187

Washer And Wiper Controls

3 — Rear Wiper/Washer

1 — Front Mist/Washer 2 — Wiper Speeds 1. Mist, Front Wiper and Washer Press the end of the multifunction lever inward to the first detent and release to clear the windshield. Pressing the multifunction lever inward to the second detent will

188 UNDERSTANDING THE FEATURES OF YOUR VEHICLE cause the washers to spray for a maximum of 10 seconds, or until the multifunction lever is released, and the wipers will cycle three times. NOTE: • If the multifunction lever is pressed while in the delay range, the wipers will operate for several seconds after the multifunction lever is released, and then resume the intermittent interval previously selected. • If the multifunction lever is pressed while in the off position, the wipers will operate for approximately two wipe cycles and automatically turn off.

2. Intermittent, Low and High Speed Wipers Use the intermittent wipers when weather conditions make a single wiping cycle, with a variable pause be- tween cycles, desirable. Rotate the end of the multifunc- tion lever to the first detent position, then turn the end of the multifunction lever to select the desired delay inter- val. The delay can be regulated from approximately two

seconds, to a maximum of 20 seconds between cycles. The time delay will be doubled if the vehicle speed is less than 10 mph (16 km/h). Low-speed is achieved by rotating the multifunction lever past the intermittent settings, to the first detent. High-speed is achieved by rotating the multifunction lever past the intermittent settings, to the second detent. 3. Rear Wiper and Washer Rotating the rotary ring to the first detent activates the rear intermittent wipers. To activate the washers, rotate the rotary ring fully forward and the washers will spray until the ring is released, and then resume the intermit- tent interval. NOTE: Rear window wipers function in the intermittent wiper speed only.

WARNING!

Sudden loss of visibility through the windshield could lead to an accident. You might not see other vehicles or other obstacles. To avoid sudden icing of the windshield during freezing weather, warm the windshield with defroster before and during wind- shield washer use.

Rain Sensing Wipers — If Equipped This feature senses moisture on the windshield and automatically activates the wipers for the driver. This feature is especially useful for road splash or overspray from the windshield washers of the vehicle ahead. Rotate the end of the multifunction lever to one of the five intermittent wiper sensitivity settings to activate this feature.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 189
The sensitivity of the system is adjustable from the multifunction lever. Wiper sensitivity position 3 has been calibrated for best overall wiping sensitivity. If the opera- tor desires more wiping sensitivity, they may select sensitivity positions 4 or 5. If the operator desires less wiping sensitivity, they may select sensitivity positions 2
or 1. Place the multifunction lever in the OFF position when not using the system. NOTE: • The rain sensing feature will not operate when the • The rain sensing feature may not function properly when ice or dried saltwater is present on the wind- shield. • Use of Rain-X威 or products containing wax or silicone

wiper speed is in the low or high position.

may reduce rain sensor performance.

190 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

• The rain sense feature can be turned on and off through the EVIC (if equipped). Refer to “Personal Settings (Customer Programmable Features)” under “Electronic Vehicle Information Center (EVIC)” in Section 4.

The rain sensing system has protective features for the wiper blades and arms. It will not operate under the following conditions: • Low Temperature Wipe Inhibit — The rain sensing feature will not operate when the ignition is first switched ON, and the vehicle is stationary, and the outside temperature is below 32°F (0°C), unless the wiper control on the multifunction lever is moved, or the vehicle speed becomes greater than 0 mph (0 km/h), or the outside temperature rises above freezing.

• Neutral Wipe Inhibit — The rain sensing feature will not operate when the ignition is ON, and the trans- mission shift lever is in the NEUTRAL position, and the vehicle speed is less than 5 mph (8 km/h), unless the wiper control on the multifunction lever is moved or the shift lever is moved out of the NEUTRAL position. • Remote Start Mode Inhibit — On vehicles equipped with remote starting system, rain sensing wipers are not operational when the vehicle is in the remote start mode. Once the operator is in the vehicle and has placed the ignition switch in the RUN position, rain sensing wiper operation can resume, if it has been selected, and no other inhibit conditions (mentioned previously) exist.

TILT STEERING COLUMN — IF EQUIPPED This feature allows you to tilt the steering column upward or downward. The tilt control lever is located on the steering column, below the steering wheel. To tilt the column, push the lever downward to the unlocked position. Move the steering column up or down, as desired. Pull the lever upward to the locked position to lock the steering column firmly in place.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 191

Tilt Steering Column Lever

1 — Locked Position 2 — Unlocked Position

192 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

WARNING!

Tilting the steering column while the vehicle is moving is dangerous. Without a stable steering col- umn, you could lose control of the vehicle and have an accident. Adjust the column only while the ve- hicle is stopped. Be sure it is locked before driving.

ADJUSTABLE PEDALS — IF EQUIPPED This feature allows both the brake and accelerator pedals to move toward, or away, from the driver to provide improved position with the steering wheel. The adjust- able pedal system is designed to allow a greater range of driver comfort for steering wheel tilt and seat positions. The switch is located on the left side of the steering column.

Adjustable Pedal Switch

Press the button forward to move the pedals forward (toward the front of the vehicle). Press the button rearward to move the pedals rearward (toward the driver). • The pedals can be adjusted with the ignition OFF.

• The pedals can be adjusted while driving. • The pedals cannot be adjusted when the vehicle is in REVERSE or when the Electronic Speed Control Sys- tem is on. The following messages will be displayed on vehicles equipped with the Electronic Vehicle In- formation System (EVIC) if the pedals are attempted to be adjusted when the system is locked out (“Adjust- able Pedal Disabled — Cruise Control Engaged” or “Adjustable Pedal Disabled — Vehicle In Reverse”.

CAUTION!

Do not place any article under the adjustable pedals or impede its ability to move, as it may cause damage to the pedal controls. Pedal travel may become lim- ited if movement is stopped by an obstruction in the adjustable pedal’s path.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 193
ELECTRONIC SPEED CONTROL — IF EQUIPPED When engaged, Electronic Speed Control takes over the accelerator operation at speeds greater than 25 mph (40 km/h).

Electronic Speed Control Lever

194 UNDERSTANDING THE FEATURES OF YOUR VEHICLE In order to ensure proper operation, the Elec- NOTE: tronic Speed Control System has been designed to shut down if multiple Speed Control functions are operated simultaneously. If this occurs, the Electronic Speed Con- trol System can be reactivated by pushing the Electronic Speed Control ON/OFF button and resetting the desired vehicle set speed. To Activate Push the ON/OFF button (located in the end of the lever) once, and the cruise indicator light (located in the mes- sage window of the odometer) will illuminate, showing that the Electronic Speed Control system is on. To turn the Electronic Speed Control system off, push the ON/ OFF button a second time, and both the Electronic Speed Control system and indicator will turn off.

WARNING!

Leaving the Electronic Speed Control system on when not in use is dangerous. You could accidently set the system or cause it to go faster than you want. You could lose control and have an accident. Always leave the Electronic Speed Control system off when you are not using it.

To Set At A Desired Speed When the vehicle has reached the desired speed, press the SET lever downward and then release. Lift your foot off the accelerator and the vehicle will operate at the selected speed. Deactivating Electronic Speed Control A soft tap on the brake pedal or pulling the Electronic Speed Control lever (CANCEL) toward you will deacti- vate the Electronic Speed Control without erasing the set

speed memory. Pushing the ON/OFF button to the OFF position or turning OFF the ignition erases the set speed memory. Resuming Speed To resume a previously set speed, raise the Electronic Speed Control lever (RESUME/ACCEL) upward, and release. Resume can be used at any speed above 25 mph (40 km/h). Varying The Speed Setting When the Electronic Speed Control is set, speed can be increased by raising and holding the RESUME/ACCEL lever upwards. When released, a new set speed will be established. Raising the RESUME/ACCEL lever upward, once, will result in a 1 mph (1.6 km/h) speed increase. Each time the lever is tapped upward speed increases, so tapping the Electronic Speed Control lever three times will in- crease speed by 3 mph (5 km/h), etc.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 195
To decrease speed while speed control is set, press the SET/DECEL lever downward, and hold. Release the Electronic Speed Control lever when the desired speed is reached, and the new speed will be set. Tapping the SET/DECEL lever downward, once, will result in a 1 mph (1.6 km/h) speed decrease. Each time the Electronic Speed Control lever is tapped downward, speed decreases. Accelerating To Pass Press the accelerator as you normally would. When the pedal is released, the vehicle will return to the set speed. NOTE: The Electronic Speed Control system maintains speed up and down hills. A slight speed change on moderate hills is normal.

196 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Your vehicle may experience a downshift (automatic transmissions only) while climbing uphill or descending downhill. This downshift is necessary to maintain vehicle set speed. On steep hills, a greater speed loss or gain may occur, so it may be preferable to drive without Electronic Speed Control.

WARNING!

Electronic Speed Control can be dangerous where the system cannot maintain a constant speed. Your ve- hicle could go too fast for the conditions, and you could lose control. An accident could be the result. Do not use Electronic Speed Control in heavy traffic or on roads that are winding, icy, snow-covered, or slippery.

REAR PARK ASSIST — IF EQUIPPED The Rear Park Assist provides visible and audible indi- cations of the distance between the rear fascia and the detected obstacle, when backing up. When backing up, you should also use the inside rearview and outside mirrors. The Rear Park Assist will remember the last system state (enabled or disabled) from the last ignition cycle, when the ignition is changed to the RUN/ON position. The Rear Park Assist can be active only when the shift lever is in REVERSE. When in REVERSE, the system scans for objects behind the vehicle, using four sensors located in the rear bumper. NOTE: The system will be active until the vehicle speed is increased to approximately 11 mph (18 km/h) or above. The system will be active again if the vehicle speed is decreased to speeds less than approximately 10 mph (16 km/h).

Rear Park Assist Sensors The four Rear Park Assist sensors, located in the rear fascia, monitor the area behind the vehicle that is within the sensors’ field of view. The monitored area seems oval in shape. The sensors can detect obstacles from approxi- mately 11.8 in (30 cm) up to 78.7 in (200 cm) from the rear fascia in the horizontal direction, depending on the location and orientation of the obstacle and the type of obstacle. Rear Park Assist Warning Display The Rear Park Assist Warning Display, located in the headliner near the liftgate glass, provides both visible and audible warnings to indicate the distance between the rear fascia and the detected obstacle.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 197

Rear Park Assist LED Lights

When the ignition switch is turned to the RUN/ON position, the warning display will turn on all of its LEDs for about one second. Each side of the warning display has six yellow and two red LED lights, one set to warn of obstacles behind the left rear of the vehicle and the other set to warn of obstacles behind the right rear of the vehicle. The vehicle is close to the obstacle when the red LED is illuminated.

198 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The driver can view the LEDs either through the rear- view mirror or by looking directly at the display above the rear window.

WARNING DISPLAY DISTANCES

The system dimly illuminates the two innermost yellow LEDs when it is on and detects no obstacles. The follow- ing chart shows the warning display operation when the system is detecting an obstacle.

DISPLAY INDICA-

TOR

Inner LED 1st LED 2nd LED 3rd LED 4th LED 5th LED 6th LED 7th LED

OBSTACLE DISTANCE FROM:

REAR CORNERS

31.5 in (80 cm) 25.5 in (65 cm) 20 in (50 cm) 16 in (40 cm) 6 in (15 cm)

REAR CENTER 59 in (150 cm) 51.2 in (130 cm) 45.3 in (115 cm) 39.3 in (100 cm) 33.5 in (85 cm) 27.6 in (70 cm) 19.7 in (50 cm) 11.8 in (30 cm)

INDICATOR

COLOR Yellow Yellow Yellow Yellow Yellow Yellow Red Red

AUDIBLE SIGNAL

Yes, Half Second

No No No No No

Yes, Intermittent Yes, Continuous

NOTE: The Rear Park Assist will MUTE the radio, if on, when the audible warning is activated.

WARNING!

• Drivers must be careful when backing up, even when using the Rear Park Assist. Always check carefully behind your vehicle, and be sure to check for pedestrians, animals, other vehicles, obstruc- tions, or blind spots before backing up. You are responsible for the safety of your surroundings and must continue to pay attention while backing up. Failure to do so can result in serious injury or death.

(Continued)

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 199

WARNING! (Continued)

• Before using the Rear Park Assist, it is strongly recommended that the ball mount and hitch ball assembly be disconnected from the vehicle, when the vehicle is not used for towing. Failure to do so can result in injury or damage to vehicles or obstacles, because the hitch ball will be much closer to the obstacle than the rear fascia when the warning display turns the red LEDs on. Also, the sensors could detect the ball mount and hitch ball assembly, depending on its size and shape, giving a false indication that an obstacle is behind the vehicle.

200 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

CAUTION!

• To avoid vehicle damage, the Rear Park Assist should only be used as a parking aid and is unable to recognize every obstacle, including small ob- jects. Parking curbs might be temporarily detected or not detected at all. Obstacles located above or below the sensors will not be detected when they are in close proximity to the rear of the vehicle. • To avoid vehicle damage, the vehicle must be driven slowly when using the Rear Park Assist, to be able to stop in time when an obstacle is detected. It is recommended that you look over your shoulder when using the Rear Park Assist.

NOTE: • Ensure that the rear bumper is free of dirt and debris

to keep the system operating properly.

• Jackhammers, large trucks, and other vibrations could

affect the performance of the system.

Enabling and Disabling The Rear Park Assist There are times when you may want to disable the Rear Park Assist, such as when towing a trailer. Vehicles Equipped With the Electronic Vehicle Information Center (EVIC) You can turn the Rear Park Assist ON or OFF through the EVIC. For details, refer to “Personal Settings (Customer- Programmable Features)” under “Electronic Vehicle In- formation Center (EVIC)” in Section 4. Vehicles Equipped With the Compass Mini-Trip Computer (CMTC) You can turn the Rear Park Assist ON or OFF through the CMTC by pressing the left reset button in the instrument cluster. Turn the ignition switch to the ON position, then press and hold the RESET button for approximately two seconds.

Service The Rear Park Assist If the Rear Park Assist malfunctions, the instrument cluster will actuate a single chime, once per ignition cycle, and it will display the ⴖSERVICE PARK ASSIST SYSTEMⴖ message. Refer to “Compass Mini Trip Com- puter (CMTC) or “Electronic Vehicle Information Center (EVIC) — If Equipped”, in Section 4. If ⴖSERVICE PARK ASSIST SYSTEMⴖ appears in the Electronic Vehicle Information Center (EVIC), after mak- ing sure the rear bumper is clean, please see your authorized dealer.

Should this wrench symbol display with the letter P next to it, your Park Sense system needs servicing. Contact your authorized dealer.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 201

Cleaning The Rear Park Assist Clean the Rear Park Assist sensors with water, car wash soap and a soft cloth. Do not use rough or hard cloths. Do not scratch or poke the sensors, otherwise, you could damage them.

REAR BACKUP CAMERA SYSTEM — IF EQUIPPED Your vehicle may be equipped with a Rear Camera System that allows you to see an on-screen image of the rear of your vehicle whenever the shift lever is put into REVERSE. The Rear camera image will be displayed on the uconnect™ tunes radio display screen, located on the center stack of the instrument panel. The camera is located in the light bar over the rear license plate.

202 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

WARNING!

Drivers must be careful when backing up even when using the Rear Backup Camera System. Always check carefully behind your vehicle, and be sure to check for pedestrians, animals, other vehicles, ob- structions, or blind spots before backing up. You are responsible for the safety of your surroundings and must continue to pay attention while backing up. Failure to do so can result in serious injury or death.

CAUTION!

• To avoid vehicle damage, the Rear Camera system should only be used as a parking aid. The Rear Camera system is unable to view every obstacle or object in your drive path.

(Continued)

CAUTION! (Continued)

• To avoid vehicle damage, the vehicle must be driven slowly when using the Rear Camera system to be able to stop in time when an obstacle is seen. It is recommended that the driver look frequently over his/her shoulder when using the Rear Camera system.

If snow, ice, mud, or anything else builds up on NOTE: the camera lens, clean the lens, rinse with water, and dry with a soft cloth. Do not cover the lens. Turning the Rear Camera On or Off — With Navigation Radio 1. Press the ⬙menu⬙ hard key. 2. Select ⬙system setup⬙ soft key. 3. Press the “camera setup” soft key.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 203
3. Enable or disable the rear camera feature by selecting ⬙enable rear camera in reverse⬙ soft key. 4. When the vehicle is shifted into REVERSE, an image of the rear of the vehicle will appear with a caution note to ⬙check entire surroundings⬙ displayed across the top of the screen. After five seconds this note will disappear. 5. When the vehicle is shifted out of REVERSE, the rear camera mode is exited and the audio screen appears again.

4. Enable or disable the rear camera feature by selecting ⬙enable rear camera in reverse⬙ soft key. 5. Press the “save” soft key. 6. When the vehicle is shifted into REVERSE, an image of the rear of the vehicle will appear with a caution note to ⬙check entire surroundings⬙ displayed across the top of the screen. After five seconds this note will disappear. 7. When the vehicle is shifted out of REVERSE, the rear camera mode is exited and the navigation or audio screen appears again. Turning the Rear Camera On or Off — Without Navigation Radio 1. Press the ⬙menu⬙ hard key. 2. Select ⬙system setup⬙ soft key.

204 UNDERSTANDING THE FEATURES OF YOUR VEHICLE OVERHEAD CONSOLES

Front Overhead Console Two versions of the overhead console are available. The base front overhead console model featured fixed incan- descent courtesy/reading lights, flip-down sunglass stor- age and conversation mirror. The premium front over- head console model features a LED focused light that illuminates the instrument panel cupholders, Infrared Automatic Temperature Control Sensor (ATC equipped only), two swiveling LED lights, flip-down sunglass storage, conversation mirror, optional power sliding door switches and an optional power liftgate switch. NOTE: Premium sunroof console models include all of above except sunglass storage.

Front Premium Overhead Console Features

1 — Cupholder LED 2 — ATC Sensor 3 — Interior Lights

4 — Storage/Mirror 5 — Switch Bank

Courtesy/Interior Lighting At the forward end of the console are two courtesy lights (standard dome light has two buttons). The lights turn on when a front door, a sliding door or the liftgate is opened. If your vehicle is equipped with Remote Keyless Entry (RKE) the lights will also turn on when the UNLOCK button on the RKE transmitter is pressed. The courtesy lights also function as reading lights. Press in on each lens to turn these lights on while inside the vehicle. Press a second time to turn each light off. You may adjust the direction of these lights by pressing the outside ring, which is identified with four directional arrows (LED lamps only). The area around the instrument panel cupholders is also illuminated from a light in the overhead console (pre- mium console only). This light is turned on when the headlight switch is on, and will adjust in brightness when the dimmer control is rotated up or down.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 205

Sunglass Storage (non-sunroof only) At the rear of the front overhead console, a compartment is provided for the storage of two pairs of sunglasses. From the closed position, press the door over-travel latch to open the compartment. The door will slowly rotate to the full open position. From this position, the door can be fully closed or, by rotating upward about 3/4 of the way and releasing, positioned for conversation mirror use. From the ⬙conversation mirror⬙ position, the door can only be closed. To return to the full open position, the door must first be closed and then opened by pressing the over-travel latch again to release. NOTE: The front overhead console supplied with fac- tory sunroof, incorporates a sunroof switch.

206 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Rear Overhead Consoles — If Equipped The rear overhead storage system is available in two versions: with or without sunroof. An additional LED at the front of the rear console shines down on the front foot-well area while in courtesy mode, for added convenience.

Overhead Compartment Features

1 — DVD 1
2 — Rear HVAC 3 — Interior Lights 4 — Storage 1 If equipped, otherwise storage.

5 — Storage 6 — DVD 1
7 — Interior Lights 8 — Halo Lighting

Rear Courtesy/Reading Lights — If Equipped The overhead console has two sets of courtesy lights. The lights turn on when a front door, a sliding door or the liftgate is opened. If your vehicle is equipped with Remote Keyless Entry (RKE) the lights will also turn on when the UNLOCK button on the RKE transmitter is pressed. The courtesy lights also function as reading lights. Press in on each lens to turn these lights on while inside the vehicle. Press the lens a second time to turn each light off. You may adjust the direction of these lights by pressing the outside ring, which is identified with four directional arrows. Rear Console Halo Lighting The rear overhead console has recessed halo lighting around the perimeter of the console base. This feature provides additional lighting options while traveling and

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 207
is controlled by the headlight switch. Refer to ”Halo Lights — If Equipped” under “Lights” in Section 3.

GARAGE DOOR OPENER — IF EQUIPPED HomeLink威 replaces up to three remote controls (hand- held transmitters) that operate devices such as garage door openers, motorized gates, lighting, or home security systems. The HomeLink威 unit operates off your vehicle’s battery. The HomeLink威 buttons that are located in the headliner or sun visor designate the three different HomeLink威 channels.

208 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

HomeLink威 Buttons

NOTE: HomeLink威 is disabled when the Vehicle Secu- rity Alarm is active.

WARNING!

• Your motorized door or gate will open and close while you are training the universal transceiver. Do not train the transceiver if people or pets are in the path of the door or gate. Only use this trans- ceiver with a garage door opener that has a “stop and reverse” feature as required by Federal safety standards. This includes most garage door opener models manufactured after 1982. Do not use a garage door opener without these safety features. Call toll-free 1–800–355–3515 or, on the Internet at www.HomeLink.com for safety information or as- sistance. • Vehicle exhaust contains carbon monoxide, a dan- gerous gas. Do not run your vehicle in the garage while training the transceiver. Exhaust gas can cause serious injury or death.

Programming HomeLink姞

Before You Begin If you have not trained any of the HomeLink威 buttons, erase all channels before you begin training. To do this, press and hold the two outside buttons for up to 20 seconds until the red indicator flashes. It is recommended that a new battery be placed in the hand-held transmitter of the device being programmed to HomeLink威 for more efficient training and accurate transmission of the radio-frequency signal. Your vehicle should be parked outside of the garage when programming. Begin Programming 1. Turn the ignition switch to the ON/RUN position. 2. Hold the battery side of the hand-held transmitter away from the HomeLink威 button you wish to program.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 209
Place the hand-held transmitter 1 to 3 in (3 to 8 cm) away from the HomeLink威 button you wish to program while keeping the indicator light in view. 3. Simultaneously press and hold both the chosen HomeLink威 button and the hand-held transmitter button until the HomeLink威 indicator changes from a slow to a rapidly blinking light, then release both the HomeLink威 and hand-held transmitter buttons. Watch for the HomeLink威 indicator to change flash rates. When it changes, it is programmed. It may take up to 30 seconds, or longer in rare cases. The garage door may open and close while you train. NOTE: • Some gate operators and garage door openers may require you to replace Step 3 with procedures noted in the “Gate Operator/Canadian Programming” section.

210 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

• After training a HomeLink威 channel, if the garage door does not operate with HomeLink威 and the ga- rage door opener was manufactured after 1995, the garage door opener may have a rolling code. If so, proceed to Step 5 “Programming A Rolling Code System.”

4. Press and hold the just-trained HomeLink威 button and observe the indicator light. If the indicator light stays on constantly, programming is complete and the garage door (or device) should activate when the HomeLink威 button is pressed. If the indicator light blinks rapidly for two seconds and then turns to a constant light, proceed to Step 5 “Pro- gramming A Rolling Code System.” 5. Programming A Rolling Code System At the garage door opener motor (in the garage), locate the “Learn” or “Training” button.

This can usually be found where the hanging antenna wire is attached to the garage door opener motor. It is NOT the button normally used to open and close the door.

Training The Garage Door Opener

1 — Door Opener 2 — Training Button

6. Firmly press and release the “Learn” or “Training” button. The name and color of the button may vary by manufacturer. NOTE: There are 30 seconds in which to initiate the next step after the “Learn” button has been pressed. 7. Return to the vehicle and press the programmed HomeLink威 button twice (holding the button for two seconds each time). If the device is plugged in and activates, programming is complete. If the device does not activate, press the button a third time (for two seconds) to complete the training. If you have any problems, or require assistance, please call toll-free 1–800–355–3515 or, on the Internet at www.HomeLink.com for information or assistance. To program the remaining two HomeLink威 buttons, repeat each step for each remaining button. DO NOT erase the channels.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 211

Using HomeLink威 To operate, simply press and release the programmed HomeLink威 button. Activation will now occur for the trained device (i.e., garage door opener, gate operator, security system, entry door lock, home/office lighting, etc. The hand-held transmitter of the device may also be used at any time. Reprogramming a Single HomeLink威 Button To reprogram a channel that has been previously trained, follow these steps: 1. Turn the ignition switch to the ON/RUN position. 2. Press and hold the desired HomeLink威 button until the indicator light begins to flash after 20 seconds. Do not release the button. 3. Without releasing the button, proceed with Program- ming HomeLink威 Step 2 and follow all remaining steps.

212 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Gate Operator/Canadian Programming Canadian radio frequency laws require transmitter sig- nals to time-out (or quit) after several seconds of trans- mission – which may not be long enough for HomeLink威 to pick up the signal during programming. Similar to this Canadian law, some U.S. gate operators are designed to time-out in the same manner. It may be helpful to unplug the device during the cycling process to prevent possible overheating of the garage door or gate motor. If you are having difficulties programming a garage door opener or a gate operator, replace “Programming HomeLink威” Step 3, with the following: 3. Continue to press and hold the HomeLink威 button while you press and release - every two seconds (“cycle”) your hand-held transmitter until HomeLink威

has successfully accepted the frequency signal. The indicator light will flash slowly and then rapidly when fully trained. If you unplugged the device for training, plug it back in at this time. Then proceed with Step 4 under “Programming HomeLink威,” earlier in this section. Security It is advised to erase all channels before you sell or turn in your vehicle. To do this, press and hold the two outside buttons for 20 seconds until the red indicator flashes. Note that all channels will be erased. Individual channels cannot be erased. The HomeLink威 Universal Transceiver is disabled when the Vehicle Security Alarm is active.

Troubleshooting Tips If you are having trouble programming HomeLink威, here are some of the most common solutions: • Replace the battery in the original transmitter. • Press the “Learn” button on the Garage Door Opener • Did you unplug the device for training, and remember

to complete the training for a Rolling Code.

to plug it back in?

If you have any problems, or require assistance, please call toll-free 1–800–355–3515 or, on the Internet at www.HomeLink.com for information or assistance. General Information This device complies with FCC rules Part 15 and Industry Canada RSS-210. Operation is subject to the following two conditions: 1. This device may not cause harmful interference.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 213
2. This device must accept any interference that may be received including interference that may cause undesired operation. NOTE: • The transmitter has been tested and it complies with FCC and IC rules. Changes or modifications not expressly approved by the party responsible for com- pliance could void the user’s authority to operate the device. • The term IC before the certification/registration num- Industry Canada technical

ber only signifies that specifications were met.

POWER SUNROOF — IF EQUIPPED The power sunroof control switch is located in the front overhead console. The sunroof panel tilts upward at the rear for ventilation or slides rearward under the roof.

214 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Power Sunroof Operation

Opening the Sunroof Manually Press the switch rearward and hold, and the sunroof will open automatically from any position. The sunroof will open fully, then stop automatically. During this opera- tion, any release of the sunroof switch will stop the sunroof.

WARNING!

In an accident, there is greater risk of being thrown from a vehicle with an open sunroof. You could also be seriously injured or killed. Always fasten your seat belt properly and make sure all passengers are properly secured.

Closing the Sunroof Manually To close the sunroof from an open or vent position, press and hold the switch forward. The sunroof will close fully and stop automatically. Release the switch to stop sun- roof travel at any point. Sunroof Sunshade Operation The sunroof sunshade can be opened manually. How- ever, the sunshade will open automatically as the sunroof opens. NOTE: The sunshade cannot be closed if the sunroof is open.

WARNING!

Never leave children in a vehicle with the key in the ignition switch. Occupants, particularly unattended children, can become entrapped by the power sun- roof while operating the power sunroof switch. Such entrapment may result in serious injury or death.

Express-Open Press the switch rearward and release, and the sunroof will open automatically from any position. The sunroof will open fully, then stop automatically. This is called “Express-Open”. During Express-Open operation, any movement of the sunroof switch will stop the sunroof. Express-Vent Press and release the ⬙V⬙ button, and the sunroof will automatically open to the vent position. This is called “Express-Vent”.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 215

Express-Close Press the switch forward and release, and the sunroof will close automatically from any position. The sunroof will close fully, then stop automatically. This is called “Express-Close”. During Express-Close operation, any movement of the sunroof switch will stop the sunroof.

WARNING!

Do not allow small children to operate the sunroof. Never allow your fingers, other body parts, or any object to project through the sunroof opening. Injury may result.

Ignition Off Operation The power sunroof switch will remain active for 10 min- utes after the ignition switch is turned OFF. Opening either front door will cancel this feature.

216 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Auto-Express with Anti-Pinch Protection During express closing, anytime an obstacle that restricts glass movement is detected, the motor will stop and reverse travel to avoid pinching the object. Auto Express will stop and reverse travel up to three times in succession. After the third time, Auto Express will enter a manual operation mode. This allows the operator to manually control the power switch, in order to close or open the sunroof in case of a malfunction. Wind Buffeting Wind buffeting can be described as the perception of pressure on the ears or a helicopter-type sound in the ears. Your vehicle may exhibit wind buffeting with the windows down, or the sunroof (if equipped) in certain open or partially open positions. This is a normal occur- rence and can be minimized. If the buffeting occurs with the rear windows open, open the front and rear windows together to minimize the buffeting. If the buffeting occurs

with the sunroof open, adjust the sunroof opening to minimize the buffeting or open any window. Sunroof Maintenance Use only a non-abrasive cleaner and a soft cloth to clean the glass panel.

ELECTRICAL POWER OUTLETS — IF EQUIPPED Two 12-Volt power outlets are located on the lower instrument panel, next to the open storage bin. The upper power outlet is controlled by the ignition switch and the lower power outlet is connected directly to the battery. The upper power outlet will also operate a conventional cigar lighter unit (if equipped with an optional Smoker’s Package). To ensure proper operation, a MOPAR威 cigar knob and element must be used.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 217
The outlet in the rear quarter panel near the liftgate and the upper outlet in the instrument panel are both con- trolled by the ignition switch. Each of these outlets can support 160 Watts (13 Amps). Do not exceed 160 Watts (13 Amps) for each of these outlets. The power outlets include tethered caps, labeled with a key or battery symbol indicating the power source. The power outlet, located on the lower instrument panel, is powered directly from the battery. Items plugged into this power outlet may discharge the battery and/or prevent the engine from starting.

12-Volt Power Outlets

One outlet in the removable floor console shares a fuse with the lower outlet in the instrument panel and is also connected to the battery. Do not exceed a maximum power of 160 Watts (13 Amps) shared between the lower panel outlet and the removable floor console outlet.

WARNING!

To avoid serious injury or death: • Do not insert any objects into the receptacles. • Do not touch with wet hands.

(Continued)

218 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

WARNING! (Continued)

• Close the lid when not in use and while driving • If this outlet is mishandled, it may cause an

the vehicle.

electric shock and failure.

CAUTION!

• Many accessories that can be plugged in draw power from the vehicle’s battery, even when not in use (i.e., cellular phones, etc.). Eventually, if plugged in long enough, the vehicle’s battery will discharge sufficiently to degrade battery life and/or prevent the engine from starting.

(Continued)

CAUTION! (Continued)

• Accessories that draw higher power (i.e., coolers, vacuum cleaners, lights, etc.), will degrade the battery even more quickly. Only use these inter- mittently and with greater caution. • After the use of high power draw accessories, or long periods of the vehicle not being started (with accessories still plugged in), the vehicle must be driven a sufficient length of time to allow the alternator to recharge the vehicle’s battery. • Power outlets are designed for accessory plugs only. Do not hang any type of accessory or acces- sory bracket from the plug. Improper use of the power outlet can cause damage.

POWER INVERTER — IF EQUIPPED A 110-Volt, 150-Watt inverter outlet (if equipped) con- verts DC current to AC current, and is located on the left rear trim panel immediately behind the second row left passenger seat. This outlet can power cellular phones, electronics and other low power devices requiring power up to 150 Watts. Certain high-end video games, such as Playstation3 and XBox360 will exceed this power limit, as will most power tools. Due to built-in overload protec- tion, the power outlet will shut down if the power rating is exceeded. Each device to be powered should be checked first to make sure it does not exceed the outlet’s 150 Watts maximum rating.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 219

Power Inverter Outlet

The power inverter switch is located near the center of the instrument panel below the two 12-Volt power out- lets.

220 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To turn on the power outlet, press the switch once. Press the switch a second time to turn the power outlet off.

Power Inverter Switch

CUPHOLDERS There are nine cupholders in the interior. Two cupholders in the center front instrument panel, four in the floor consoles and three more are located in the third row quarter trim panel. All liners are removable for cleaning. Pull the flexible liner from the cupholder drawer or tray starting at one edge for easy removal. Refer to “Cleaning The Instru- ment Panel Cupholders” in Section 7. Instrument Panel Cupholders The instrument panel cupholders are located in a pull-out drawer just above the lower storage bin.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 221

Interior Bottle Holders There are four bottle holders located in the interior. One bottle holder is molded into each front interior door trim panels, and one bottle holder is molded into each side sliding interior door trim panel. Each holder accommo- dates up to a 20 oz (1 L) plastic bottle.

WARNING!

If containers of hot liquid are placed in the bottle holder, they can spill when the door is closed, burn- ing the occupants. Be careful when closing the doors to avoid injury.

Front Cupholders

Pull the drawer out firmly until it stops, and place the container to be held in either one of the cupholder wells. The cupholders are designed to accommodate a wide variety of container types and sizes. Press down on the container to engage the cupholder retention features.

222 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Interior Bottle Holder

Two outboard mesh pockets are on intermediate seating. The mesh pockets are flexible enough to hold juice boxes, toys, games or MP3 players, etc.

Smoker’s Package Kit — If Equipped With the optional authorized dealer-installed Smoker’s Package Kit, a removable ash receiver is inserted into one of the two cupholders in the center front instrument panel. To install the ash receiver, align the receiver so the thumb grip on the lid is facing rearward. Press the ash receiver into either of the cup wells to secure. Pull upward on the ash receiver to remove for cleaning and/or storage. The left rear trim panel cupholder is designed to accom- modate a second ash receiver, if desired.

STORAGE

Glove Compartments

Upper Glove Compartment To open the upper compartment, press inward on the release button (2). The door will spring open about 1 in (2.54 cm). Manually lift the front edge of the door upward, until fully opened, and the detent is engaged. To close the compartment door, push firmly downward on the door’s surface to release the detent and latch the door closed.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 223

Glove Compartment Features

3 — Lower Latch/Lock 4 — Lower Compartment

1 — Upper Compartment 2 — Upper Latch Lower Glove Compartment To open the lower compartment, pull out on the release handle (3). The lower compartment handle is also equipped with a lock (3).

224 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Door Trim Panel Storage

Front Door Storage Both interior front door panels have multiple pockets for storage.

Driver Seatback Storage — If Equipped The drivers seatback has a primary storage pocket on all models and an optional secondary mesh pocket.

Front Door Storage Features

1 — Storage Pocket 2 — Map Pocket

3 — Bottle Holder 4 — Map Pocket

1 — Bag Holder 2 — Standard Pocket 3 — Mesh Pocket

Driver’s Seatback Storage

Umbrella Holder An umbrella holder has been conveniently molded into the left front door entry scuff molding.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 225

Umbrella Holder Second Row Floor Storage Bins The area below the floor covers, located in front of the second row seats, is available for storage.

Storage Bin Cover Lock Release

Pull up on the storage bin latch to open the cover. Slide the storage bin locking mechanism to the ⬙unlocked⬙ position to allow greater access to the storage bin.

226 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

CAUTION!

The storage bin cover must lay flat and be locked to avoid damage from contact with the front seat tracks, which have minimal clearance to the cover.

WARNING!

Center And Rear Overhead Console Storage — If Equipped The overhead storage system comes in several options.

covers open.

In an accident, serious injury could result if the seat storage bin covers are not properly latched. • Do not drive the vehicle with the storage bin • Keep the storage bin covers closed and latched • Do not operate the storage bin covers while the • Do not use a storage bin latch as a tie down.

while the vehicle is in motion.

vehicle is in motion.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 227

Coat Hooks Coat hooks are located along the headliner for the second and third row seating positions. The coat hook load limit is 10 lbs (4.5 kg). Exceeding the recommended load limit can cause the coat hooks to break or disengage from the vehicle. Cargo Area Storage The liftgate sill plate has a raised line with the statement “Load To This Line”. This line indicates how far rearward cargo can be placed without interfering with liftgate closing.

Overhead Console Features

1 — DVD 1
2 — Rear HVAC 3 — Courtesy Lights 4 — Storage 1 If equipped, otherwise storage.

5 — Storage 6 — DVD 1
7 — Courtesy Lights 8 — Halo Lighting

228 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Rear Cargo Area Loading Limit

NOTE: With all rear seats stowed or removed, 4 x 8foot sheets of building material will fit on the vehicle floor with the liftgate closed. The front seats must be moved slightly forward of the rearmost position.

CONSOLE FEATURES There are two consoles available: Basic and Premium.

easily pass through the first row to the second.

Basic Console Basic Console features consist of the following: • The basic console profile allows vehicle occupants to • Four cupholders accept up to extra large size beverage cups or 20 oz (.6 L) plastic bottles. Cupholders are dishwasher safe for cleaning. • The cupholders are removable to access a large storage • The basic console is removable from the vehicle for additional floor space by removing the cap and clip at the console base.

bin.

To Remove The Basic Floor Console 1. Remove the front anchor cup plug and clip. 2. Slide the console base forward while lifting slightly to clear the rear load floor hook.

3. Remove the console. To Reinstall The Basic Floor Console 1. Position the console at a slight angle (front slightly higher than the rear). 2. Slide the console rearward into the floor bracket/ hook. 3. Align the console until the front anchor cup plug hole is centered on the winch hole. 4. Reinstall the clip first and then while pushing down- ward on the console with slight pressure, reinstall the cover plug. 5. Pull up on the console to be sure it is firmly latched.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 229

WARNING!

In an accident, serious injury could result if the removable floor console is not properly installed. Always be sure the removable floor console is fully latched.

Premium Console — If Equipped The three-compartment console with sliding storage bin, sliding upper tray with storage and large console storage bin offers multiple configurations. • Four cupholders with dishwasher safe liners for clean- ing. The cupholders can accept plastic bottles, large cups or mugs with handles.

• Top tray storage • Upper storage bin can hold nine regular or 18 thin CDs

or other items

230 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

• Large console center storage will store headphones for the available rear DVD entertainment system or other items • 12-Volt DC power outlet provides continuous power inside the console for cell phones or other electronics. • Rear occupant accessible • Multiple adjustments • Removable from vehicle for additional floor space.

Premium Console Features

1 — Top Release 2 — Center Release The top and center console sections slide forward and rearward to provide added user comfort. A one-piece cup

3 — Console Release

holder insert for both cavities can easily be removed for cleaning. The cupholders will also accommodate large size cups and 20 oz (.6 L) bottles. Position 1 shows the console closed with four cupholders and a convenient storage tray.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 231
Position 2 shows the raised storage tray revealing a large storage area below.

Console Position 1

Console Position 2

Dual Storage Bins