2007 Chrysler TOWN and Country Owners Manual

before continuing to step 3. 3. Press and release the memory SET (S) button located on the driver’s door. A chime will sound signaling that you are in the memory set mode. 4. Within 5 seconds, press and release memory button 1
on the driver’s door. A chime will sound signaling to you that the driver memory has been set.

5. Within 5 seconds, press and release the UNLOCK button on the Remote Keyless Entry transmitter. A chime will sound signaling to you that the transmitter link has been successfully disabled. To disable another transmitter linked to either memory position, repeat steps 1-5 for each transmitter. NOTE: Once programmed, all transmitters linked to memory can be easily enabled or disabled at one time. Refer to the Remote Linked to Memory ⬙Customer Pro- grammable Features⬙ in the Electronic Vehicle Informa- tion Center (EVIC) for more information.

TO OPEN AND CLOSE THE HOOD To open the hood, two latches must be released. First pull the hood release lever located under the left side of the instrument panel.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 149

Hood release Lever

Next, push to the left the safety catch located under the front edge of the hood, near the center.

Hood Safety Catch

Use the hood prop rod to secure the hood in the open position. To prevent possible damage, do not slam the hood to close it. Lower the hood until it is open approximately 12

150 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

inches (30 cm) and then drop it. This should secure both latches. Never drive your vehicle unless the hood is fully closed, with both latches engaged.

WARNING!

If the hood is not fully latched, it could fly up when the vehicle is moving and block your forward vision. You could have a collision. Be sure all hood latches are fully latched before driving.

LIGHTS All of the lights, except the hazard warning lights, are controlled by switches to the left of the steering column on the instrument panel.

Headlight Switch

Interior Lights Interior lights are turned on when a door or liftgate is opened, the keyless entry transmitter is activated, or when the dimmer control is moved to the extreme top. The interior lights will automatically turn off in about 15
minutes if any of the following occur.

• A door, sliding door or the liftgate is left open. • Any overhead reading light is left on. • If the dimmer control is in the extreme top position. NOTE: The key must be out of the ignition switch or the ignition switch must be in the OFF position for this feature to operate. Park Lights

Turn this switch to the first detent to turn the park lights on. This also turns on all instrument panel

lighting. Headlights

Turn the headlight switch to the 2nd detent to turn the headlights and park lights on. This also turns on all instrument panel lighting.

To change the brightness of the instrument panel lights, rotate the dimmer control up or down.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 151

Dimmer Control

With the park lights or headlights on, rotating the dimmer control for the interior lights on the in- strument panel upward will in- crease the brightness of the instru- ment panel lights.

Dome Light Position

Rotate the dimmer control com- pletely upward to the second de- tent (extreme top position) to turn on the interior lights, except the front reading/courtesy lights. The interior remain on when the dimmer control is in this position.

lights will

152 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Interior light Defeat (OFF)

Rotate the dimmer control to the OFF position (extreme bottom). The interior lights will remain off when the doors or liftgate are open.

Parade Mode (Daytime Brightness Feature)

Rotate the dimmer control to the first detent. This feature brightens the odometer, radio and overhead displays when the park lights or headlights are on.

Automatic Headlights — If Equipped

This system automatically turns your headlights ON or OFF based on ambient light levels. To turn the system ON, turn the headlight switch to the extreme counter- clockwise position. When the sys- tem is ON, the Headlight Time Delay feature is also ON. This means your headlights will stay ON for up to 90 seconds after you turn the ignition switch OFF. To turn the Automatic System OFF, turn the headlight switch clockwise to the OFF position. NOTE: The engine must be running before the head- lights will come ON in the Automatic mode.

Daytime Running Lights (Canada/Fleet Vehicles Only) The Daytime Running Lights will come on whenever the vehicle is running, the headlights are off, and the parking brake is off. The headlight switch must be used for normal night time driving. Lights-on Reminder If the headlights or the park lights are left on, or if the dimmer control is in the extreme top position after the ignition switch is turned off, a chime will sound when the driver’s door is opened. Battery Protection This feature provides battery protection to avoid wearing down the battery if the headlights, park lights, or front fog lights are left on for extended periods of time when the ignition switch is in the LOCK position. After 3
minutes of the ignition switch being in the LOCK posi- tion and the headlight switch in any position other than

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 153

OFF or AUTO, the lights will turn off automatically until the next cycle of the ignition switch or headlight switch. The battery protection feature will be disabled if the ignition switch is turned to any other position other than LOCK during the 3 minute delay. Headlamp Delay — If Equipped This feature provides the safety of headlight illumination for up to 90 seconds, when leaving your vehicle in an unlighted area. To activate the delay feature, turn off the ignition switch while the headlights are still on. Then turn off the headlights within 45 seconds. The 90 second delay inter- val begins when headlight switch is turned off. If the headlights or park lights are turned back on or the ignition switch is turned on, the delay will be cancelled. The driver can choose, when exiting the vehicle, to have the headlamps remain on for 30, 60, or 90 seconds, or not

154 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

remain on. refer to Electronic Vehicle Information Center (EVIC) “Customer Programmable Features” for more information. If the headlights are turned off before the ignition, they will turn off in the normal manner. NOTE: The headlights must be turned off within 45
seconds of turning the ignition off to activate this feature. Front Fog Lights — If Equipped

To activate the front fog lights, turn on the park lights or the low beam headlights and pull out on the headlight switch control knob. An indicator in the headlight switch shows that the front fog lights are on. Pressing the headlight switch control knob in will turn the front fog lights off.

MULTIFUNCTION LEVER

Turn Signals Move the Multifunction Lever up or down and the arrows on each side of the base instrument cluster or Information Center flash to indicate proper operation of the front and rear turn signal lights. You can signal a lane change by moving the lever partially up or down. If either indicator flashes at a rapid rate, check for a defective outside turn signal light bulb. If one of the indicators fails to light when the lever is moved, it would suggest that the indicator light is defective.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 155

Headlight Low/High Beam Selector Switch Pull the multifunction lever toward the steering wheel to switch the headlights between HIGH and LOW beam. Passing Light You can signal another vehicle with your headlights by lightly pulling the multifunction lever toward the steer- ing wheel. This will cause the headlights to turn on at high beam and remain on until the lever is released. Windshield Wipers and Washers The wipers and washers are operated by a switch in the multifunction lever. Rotate the end of the lever to select the desired wiper speed. NOTE: Always remove any build-up of snow that prevents the windshield wiper blades from returning to the OFF position. If the windshield wiper switch is turned OFF and the blades cannot return to the OFF position, damage to the wiper motor may occur.

Turn Signal Switch

Turn Signal Warning If the vehicle electronics sense that the vehicle has traveled at over 18 mph (29 km/h) for about one mile with the turn signals on, a chime will sound to alert the driver.

156 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Windshield Wiper/Washer Control

To use the washer, press the end of the multifunction lever in when spray is desired, the washers will spray for a maximum of 20 seconds or until the lever is released. If another washer cycle is desired the end of the lever must be pressed again to get another 20 second washer cycle. If the lever is depressed while in the delay range, the

wipers will operate for several seconds after the lever is released, and then resume the intermittent interval pre- viously selected. If the end of the lever is depressed while in the OFF position, the wipers will operate for approximately two wipe cycles, then turn OFF.

WARNING!

Sudden loss of visibility through the windshield could lead to an accident. You might not see other vehicles or other obstacles. To avoid sudden icing of the windshield during freezing weather, warm the windshield with defroster before and during wind- shield washer use.

Intermittent Wiper System Use the intermittent wipers when weather conditions make a single wiping cycle, with a variable pause be- tween cycles, desirable. Rotate the end of the lever to the first detent position, then turn the end of the lever to select the desired delay interval. The delay can be regulated from a maximum of about 20 seconds between cycles, to a cycle every 2
seconds. The time delay will be doubled if the vehicle speed is less than 10 mph (16 km/h).

TILT STEERING COLUMN — IF EQUIPPED To tilt the column, pull the small lever, located behind the turn signal control, toward you and move the wheel up or down, as desired. Release the lever to lock the wheel firmly in place.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 157

Tilt Steering Column Control

158 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

WARNING!

Tilting the steering column while the vehicle is moving is dangerous. Without a stable steering col- umn, you could lose control of the vehicle and have an accident. Adjust the column only while the ve- hicle is stopped. Be sure it is locked before driving.

TRACTION CONTROL SWITCH — IF EQUIPPED The TRAC indicator, located below the instrument clus- ter odometer, will light up when the Traction Control is in use. To turn the system OFF, press the TRAC OFF switch located on the steering column, until the TRAC OFF indicator below the instrument cluster odometer lights up.

Traction Control Switch

To turn the system back ON, press the switch a second time until the TRAC OFF indicator turns OFF. NOTE: • The Traction Control System indicator comes on each time the ignition switch is turned ON. This will occur even if you used the switch to turn the system OFF.

• The Traction Control will make buzzing or clicking

sounds when in operation.

REAR PARK ASSIST SYSTEM — IF EQUIPPED This system is used to help drivers determine if an obstacle is in the way of the vehicle while it is backing up in addition to the use of inside rearview and outside mirrors. When the driver selects Reverse the system scans for objects behind the vehicle using four sensors located in the rear bumper. Objects can be detected from up to 59
inches (150 cm). A warning display above the rear window provides both visible and audible warnings indicating the distance of the object.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 159

Rear Park Assist Indicator

The warning display contains two sets of yellow and red LEDs, one set to warn of obstacles behind the left rear of the vehicle and the other set to warn of obstacles behind the right rear of the vehicle. The driver can view the LEDs either through the rear view mirror or by looking at the display above the rear window.

160 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

The system dimly illuminates the two outer most yellow LEDs when it is ON and detecting no obstacles.

The following chart shows the warning display operation when the system is detecting an obstacle:

WARNING DISPLAY DISTANCES

DISPLAY LED

OBSTACLE DISTANCE FROM:

LED COLOR

AUDIBLE SIGNAL

1st LED 2nd LED 3rd LED 4th LED 5th LED 6th LED 7th LED

8th LED

REAR CORNERS

31.5 in. (80 cm) 25.5 in. (65 cm) 20 in. (50 cm) 16 in. (40 cm)

REAR CENTER 59 in. (150 cm) 47 in. (120 cm) 39 in. (100 cm) 31.5 in. (80 cm) 25.5 in. (65 cm) 20 in. (50 cm) 16 in. (40 cm)

6 in. (15 cm)

12 in. (30 cm)

NOTE: The Rear Park Assist system will MUTE the radio, if on, when the audible warning is activated.

Yellow Yellow Yellow Yellow Yellow Yellow Red

Red

None None None None None None

at 12 in. (30 cm) In-

termittent

at 8 in. (20 cm) Con-

tinuous

WARNING!

• Drivers must be careful when backing up even when using the Rear Park Assist System. Always check carefully behind your vehicle, and be sure to check for pedestrians, animals, other vehicles, obstruc- tions, or blind spots before backing up. You are responsible for the safety of your surroundings and must continue to pay attention while backing up. Failure to do so can result in serious injury or death. • Before using the Rear Park Assist System, it is strongly recommended that the ball mount and hitch ball assembly be disconnected from the vehicle when the vehicle is not used for towing. Failure to do so can result in injury or damage to vehicles or obstacles because the hitch ball will be much closer to the obstacle than the rear fascia when the warning display turns the red LEDs ON. Also, the sensors could detect the ball mount and hitch ball assembly, depending on its size and shape, giving a false indication that an obstacle is behind the vehicle.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 161

CAUTION!

• To avoid vehicle damage the Rear Park Assist System should only be used as a parking aid and is unable to recognize every obstacle, including small objects. Parking curbs might be temporarily detected or not detected at all. Obstacles located above or below the sensors will not be detected when they are in close proximity to the rear of the vehicle. • To avoid vehicle damage the vehicle must be driven slowly when using the Rear Park Assist System to be able to stop in time when an obstacle is detected. It is recommended that the driver look over his/her shoulder when using the Rear Park Assist System.

162 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

NOTE: • Ensure that the rear bumper is free of dirt and debris • Jackhammers, large trucks, and other vibrations could

to keep the system operating properly.

affect the performance of the system.

If “Service Park Assist System” appears in the Electronic Vehicle Information Center (EVIC) after making sure the rear bumper is clean please see your authorized dealer.

ADJUSTABLE PEDALS — IF EQUIPPED This feature allows both the brake and accelerator pedals to move toward or away from the driver to provide improved position with the steering wheel. The adjust- able pedal system is designed to allow a greater range of driver comfort for steering wheel tilt and seat position. The switch is located on the right side of the steering column.

Adjustable Pedal Switch

Press the button forward to move the pedals forward (toward the front of the vehicle). Press the button rearward to move the pedals rearward (toward the driver). • The pedals can be adjusted with the ignition OFF.

• The pedals can be adjusted while driving. • The pedals cannot be adjusted when the vehicle is in R (Reverse) or when the Speed Control System is ON. The following messages will be displayed on vehicles equipped with the Electronic Vehicle Information Sys- tem (EVIC) if the pedals are attempted to be adjusted when the system is locked out (“Adjustable Pedal Disabled — Cruise Control Engaged” or “Adjustable Pedal Disabled — Vehicle In Reverse”).

CAUTION!

Do not place any article under the adjustable pedals or impede its ability to move as it may cause damage to the pedal controls. Pedal travel may become limited if movement is stopped by an obstruction in the adjustable pedal’s path.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 163

ELECTRONIC SPEED CONTROL — IF EQUIPPED When engaged, this device takes over the accelerator operation at speeds greater than 30 mph (50 km/h).

Speed Control Switches

164 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

To Activate: Push the “ON/OFF” button once and the CRUISE indi- cator located below the instrument cluster odometer will illuminate showing the electronic speed control system is on. To turn the system OFF, push the “ON/OFF” button again and the system and indicator will turn off.

WARNING!

Leaving the Electronic Speed Control system on when not in use is dangerous. You could accidently set the system or cause it to go faster than you want. You could lose control and have an accident. Always leave the system OFF when you aren’t using it.

To Set At A Desired Speed:

When the vehicle has reached the desired speed, press and release the “SET” button. Release the accelerator and the vehicle will operate at the selected speed. To Deactivate: A soft tap on the brake pedal, pushing the “CANCEL” button or normal braking while slowing the vehicle will deactivate the speed control without erasing the set speed memory. Pushing the “ON/OFF” button to the OFF position or turning off the ignition erases the set speed memory. To Resume Speed: To resume a previously set speed, push and release the “RESUME/ACCEL” button. Resume can be used at any speed above 25 mph (40 km/h).

To Vary the Speed Setting: When the speed control is set, speed can be increased by pressing and holding the “RESUME/ACCEL” button. When the button is released, a new set speed will be established. Tapping the “RESUME/ACCEL” button once will result in a 2 mph (3 km/h) speed increase. Each time the button is tapped, speed increases so that tapping the button three times will increase speed by 6 mph (10 km/h), etc. To decrease speed while speed control is set, press and hold the “COAST” button. Release the button when the desired speed is reached, and the new speed will be set. Tapping the “COAST” button once will result in a 1 mph (2 km/h) speed decrease. Each time the button is tapped, speed decreases.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 165

To Accelerate For Passing: Depress the accelerator as you would normally. When the pedal is released, the vehicle will return to the set speed. NOTE: The speed control system maintains speed up and down hills. A slight speed change on moderate hills is normal. Your vehicle will experience a downshift to 3rd gear while climbing uphill or descending downhill. This downshift to 3rd gear is necessary to maintain vehicle set speed. On steep hills a greater speed loss or gain may occur so it may be preferable to drive without speed control.

166 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

WARNING!

Speed Control can be dangerous where the system can’t maintain a constant speed. Your vehicle could go too fast for the conditions, and you could lose control. An accident could be the result. Don’t use Speed Control in heavy traffic or on roads that are winding, icy, snow-covered, or slippery.

OVERHEAD CONSOLE — IF EQUIPPED The overhead console can contain courtesy/reading lights, an optional universal garage door opener (HomeLink威), compass/ temperature display, a mini-trip computer, optional elec- tronic vehicle information center (EVIC), power sliding door switches and an optional power liftgate switch.

sunglasses,

storage

for

Courtesy/Reading Lights

Overhead Console

At the forward end of the console are two courtesy/ reading lights. Press the lens to turn these lights on. Press a second time to turn the lights off.

The lights also turn on when a front door, a sliding door or the liftgate is opened. If your vehicle is equipped with Remote Keyless Entry, the lights will also turn on when the unlock button on the transmitter is pressed. The area around the instrument panel cupholders is also illuminated from a light in the overhead console. This light is turned on when the headlight switch is on and will adjust in brightness when the dimmer control is rotated up or down. Sunglass Storage At the rear of the overhead console, a compartment is provided for the storage of two pair of sunglasses. Press the door latch to open the compartment. The door will slowly rotate to an open position.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 167

Compass/Temperature Display This display provides the outside temperature and one of eight compass readings to indicate the direction the vehicle is facing.

WARNING!

Even if the display still reads a few degrees above 32°F ( 0°C), the road surface may be icy, particularly in woods or on bridges. Drive carefully under such conditions to prevent an accident and possible per- sonal injury or property damage.

Automatic Compass Calibration This compass is self calibrating which eliminates the need to manually set the compass. When the vehicle is new, the compass may appear erratic and the “CAL” symbol will be displayed. After completing three 360°

168 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

turns in an area free from large metal or metallic objects, the “CAL” symbol will turn off and the compass will function normally. Manual Compass Calibration If the compass appears erratic and the “CAL” symbol does not appear, you must put the compass into the Calibration Mode manually. To put into a Calibration Mode: Turn on the ignition switch and set the display to Comp/Temp. Press the RESET button on vehicles equipped with a Compass/ Mini Trip Computer for at least 10 seconds until the “CAL” symbol appears. On vehicles equipped with Compass/Temp press and hold the C/T and US/M buttons for 10 seconds. Release the RESET button and complete three 360° turns in an area free from large metal objects. The “CAL” symbol will turn off and the compass will function normally.

CAUTION!

Do not place any external magnets, such as magnetic roof mount antennas, in the vicinity of the compass. Do not use magnetic tools when servicing the over- head console.

Compass Variance Compass Variance is the difference between magnetic North and Geographic North. In some areas of the country, the difference between magnetic and geographic North is great enough to cause the compass to give false readings. If this occurs, the compass variance must be set. NOTE: Magnetic materials should be kept away from the overhead console.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 169

To set the variance: Turn the ignition switch ON and set the display to Comp/Temp. On vehicles equipped with a Compass/Mini Trip Computer press the RESET button for approximately 5 seconds. On vehicles equipped with Compass/Temp press and hold the C/T and US/M buttons for 5 seconds. The “VAR” symbol will light and the last variance zone number will be displayed. Press the STEP button on vehicles equipped with a Compass/ Mini Trip Computer or the US/M button on vehicles equipped with Compass/Temp to select the proper vari- ance zone as shown in the map. Press the RESET button on vehicles equipped with a Compass/Mini Trip Com- puter or the C/T button on vehicles equipped with Compass/Temp to set the new variance zone and resume normal operation.

170 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Mini-Trip Computer This displays information on the following: • Average Fuel Economy (ECO AVG) Shows the average fuel economy since the last reset. • Distance To Empty (DTE) Shows the estimated distance that can be travelled with the fuel remaining in the tank. This estimated distance is determined using the MPG for the last few minutes. • Trip Odometer (ODO) Shows the distance travelled since the last reset. • Elapsed Time (ET) Shows the accumulated ignition ON time since the last reset. • Off Mode Shows a blank display.

• Step Button Push this button to cycle through all the Compass/Mini- trip Computer displays. • US/M Button Press this button to convert the display from U.S. to metric. To Reset The Display Pressing the Reset button once will clear the resettable function currently being displayed. Resettable functions are average fuel economy, trip odometer and elapsed time. Pressing the reset button twice within four seconds will clear all resettable functions. Reset will only occur if a resettable function is currently being displayed.

Electronic Vehicle Information Center (EVIC) — If Equipped The Electronic Vehicle Information Center, when the appropriate conditions exist, displays the following WARNING messages and symbols. Each message is accompanied by a single chime: • TURN SIGNALS ON (with graphic) • PERFORM SERVICE • DOOR AJAR (one or more, with graphic) • LIFTGATE AJAR (with graphic) • WASHER FLUID LOW (with graphic) • 1,2,3 OR 4 LOW TIRE(S) PRESSURE (Refer to ”Tire Pressure Monitor System” in the “Starting And Oper- ating, Tire Section”)

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 171

Equipped

• CHECK TPM SYSTEM (Refer to ”Tire Pressure Moni- tor System” in the “Starting And Operating, Tire Section”)

• MEMORY SEAT DISABLED (Not in Park) — If • ADJUSTABLE PEDAL DISABLED/CRUISE EN- • ADJUSTABLE PEDAL DISABLED/VEHICLE IN RE- • REAR PARK ASSIST (Shown in Reverse only with a

GAGED

VERSE

single chime) — If Equipped

NOTE: Tire pressure menu items are available only on vehicles equipped with the Tire Pressure Monitor Sys- tem.

172 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Customer Programmable Features — If Equipped Press the “MENU” button until one of the display choices following appears: Language When in this display you may select one of five lan- guages for all display nomenclature, including the trip computer functions. Press the “STEP” button while in this display selects English, Francaise, Deutsch, Italiano, or Espanol. As you continue the displayed information will be shown in the selected language. Rear Park Assist — If Equipped When this feature is selected the system scans for objects behind the vehicle using four sensors located in the rear bumper. Objects can be detected from up to 59 inches (150 cm). Pressing the “STEP” button while in this display will disable/enable the Rear Park Assist System.

US or Metric Pressing the “STEP” button when in this display selects US or Metric. The overhead console and climate control displays will be in the selected units. Service Interval When this feature is selected a service interval between 2,000 miles (3 200 km) and 6,000 miles (9 600 km) in 500
mile (800 km) increments may be selected. Pressing the “STEP” button when in this display will select distances between 2,000 miles (3 200 km) and 6,000 miles (9 600
km) in 500 mile (800 km) increments. Reset Service Distance (Displays Only if Service Interval was Changed) When this feature is selected the current accumulated service distance can be reset to the newly selected service interval. Pressing the “STEP” button when in this display will select “Yes” or “No.”

Use Factory Settings If “Yes” is selected, all of the customer programmable features will be set to the factory default and not dis- played. If “No” is selected you can program the Vehicle Information Center to your own personal preferences. Auto Door Locks When this feature is selected, all doors and the liftgate lock automatically when the speed of the vehicle reaches 18 mph (29 km/h). Pressing the “STEP” button when in this display will select “Yes” or “No.” Auto Unlock On Exit (Available Only When the AUTO DOOR LOCKS Feature is Turned On) When this feature is selected all the vehicle’s doors will unlock whenever any door is opened if the vehicle is stopped and the transmission is in “P” (Park) or “N” (Neutral) position. Pressing the “STEP” button when in this display will select “Yes” or “No.”

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 173

Remote Unlock Driver’s Door 1st When this feature is selected only the driver’s door will unlock on the first press of the remote keyless entry unlock button and require a second press to unlock the remaining locked doors and liftgate. When “REMOTE UNLOCK ALL DOORS” is selected all of the doors and the liftgate will unlock at the first press of the remote keyless entry unlock button. Pressing the “STEP” button when in this display will select “DRIVER’S DOOR 1ST” or “ALL DOORS”. Remote Linked To Memory (Available with Memory Seat and Pedals Only) When this feature is selected, pressing the Unlock button on any Remote Keyless Entry transmitter already linked to memory will return the driver’s seat, driver’s outside mirror, adjustable brake and accelerator pedals, and radio station presets to their memory set positions.

174 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

If this feature is not selected, the driver’s seat, driver’s mirror, adjustable pedals, and radio settings can only return to their memory set positions using the memory recall buttons (1 or 2) on the driver’s door panel. Any transmitter linked to memory will remain linked, but will not recall the memory positions. The transmitter memory recall function will operate again when this feature is selected. Refer to Driver Memory System for more information. Pressing the ⬙STEP⬙ button when in this mode will select between ⬙Yes⬙ or ⬙No⬙. Sound Horn On Lock When this feature is selected a short horn sound will occur when the remote keyless entry “Lock” button is pressed. This feature may be selected with or without the flash lights on LOCK/UNLOCK feature. Pressing the “STEP” button when in this display will select “Yes” or “No.”

Flash Lights On Lock/Unlock? When this feature is selected, the front and rear turn signals will flash when the doors are locked or unlocked using the remote keyless entry transmitter. This feature may be selected with or without the sound horn on lock feature selected. Pressing the “STEP” button when in this display will select “Yes” or “No.” Sliding Door Open Flash? When this feature is selected, and the sliding door(s) are opened, the left and right exterior hazard lights will flash for 12 seconds to alert other drivers in the area that passenger(s) could be entering or exiting the vehicle. Pressing the ⬙STEP⬙ button when in this display will select “Yes” or “No.” Headlamp Delay When this feature is selected the driver can choose, when exiting the vehicle, to have the headlamps remain on for

30, 60, or 90 seconds, or not remain on. Pressing the “STEP” button when in this display will select 30, 60, 90, or “OFF.” Headlamp On With Wipers (Available with Auto Headlights Only) When this feature is selected and the headlight switch has been moved to the “AUTO” position, the engine is running and, the front wipers are turned on for 10
seconds, the headlights will turn ON. The display will remain on Parade Mode (Daytime Brightness) for ease of viewing. Pressing the “STEP” button when in this display will select “Yes” or “No.” Power Accessory Delay When this feature is selected, accessory power will be supplied for up to 45 seconds for the power windows,

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 175

radio, power vent windows, power outlets, and remov- able center console, when the ignition switch is turned off or until the key is removed and either front door is opened.

GARAGE DOOR OPENER — IF EQUIPPED The HomeLink威 Universal Transceiver replaces up to three remote controls (hand held transmitters) that oper- ate devices such as garage door openers, motorized gates, or home lighting. It triggers these devices at the push of a button. The Universal Transceiver operates off your vehicle’s battery and charging system; no batteries are needed. NOTE: The HomeLink威 Universal Transceiver is dis- abled when the Vehicle Theft Alarm is active. For additional information on HomeLink威, call 1–800– 355–3515, or on the internet at www.homelink.com.

176 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

WARNING!

WARNING!

A moving garage door can cause injury to people and pets in the path of the door. People or pets could be seriously or fatally injured. Only use this transceiver with a garage door opener that has a “stop and reverse” feature as required by federal safety stan- dards. This includes most garage door opener mod- els manufactured after 1982. Do not use a garage door opener without these safety features it could cause injury or death. Call toll-free 1–800–355–3515
or, on the Internet at www.homelink.com for safety information or assistance.

Vehicle exhaust contains carbon monoxide, a danger- ous gas. Do not run the vehicle’s exhaust while training the transceiver. Exhaust gas can cause seri- ous injury or death.

WARNING!

Your motorized door or gate will open and close while you are training the Universal Transceiver. Do not train the transceiver if people or pets are in the path of the door or gate. A moving door or gate can cause serious injury or death to people and pets or damage to objects.

Programming HomeLink

NOTE: When programming a garage door opener, it is advised to park outside the garage. Some vehicles may require the ignition switch to be turned to the second (Accessory) position for programming and/or operation of HomeLink. It is also recommended that a new battery be placed in the hand-held transmitter of the device being programmed to HomeLink for more efficient train- ing and accurate transmission of the radio-frequency signal. 1. Press and hold the two outer HomeLink buttons, and release only when the indicator light begins to flash or the EVIC display shows “Channels Cleared” (after 20
seconds). Do not hold the buttons for longer than 30
seconds and do not repeat Step One to program a second and/or third hand-held transmitter to the remaining two HomeLink buttons.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 177

HomeLink Buttons

2. Position the end of your hand-held transmitter 1-3
inches (3-8 cm) away from the HomeLink buttons while keeping the indicator light in view.

178 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

3. Simultaneously press and hold both the HomeLink button that you want to train and the hand-held trans- mitter buttons. Do not release the buttons until Step Four has been completed. NOTE: Some gate operators and garage door openers may require you to replace this Programming Step 3 with procedures noted in the ⬙Gate Operator/Canadian Pro- gramming⬙ section. 4. The HomeLink indicator light will flash slowly and then rapidly after HomeLink successfully receives the frequency signal from the hand-held transmitter. Release both buttons after the indicator light changes from the slow to the rapid flash. 5. Press and hold the just trained HomeLink button and observe the indicator light or the EVIC display. If the indicator light stays on constantly, programming is complete and your device should activate when the HomeLink button is pressed and released.

NOTE: To program the remaining two HomeLink but- tons, begin with ⬙Programming⬙ Step Two. Do not repeat Step One.

If your hand-held transmitter appears to pro- NOTE: gram the universal transceiver, but your garage door does not operate using the transmitter and your garage door opener was manufactured after 1995, your garage door opener may have a multiple security code system (rolling code system). If your garage door is the “rolling code” type, please proceed to the heading “Program- ming A Rolling Code System.”

Programming A Rolling Code System 1. At the garage door opener receiver (motor-head unit) in the garage, locate the ⬙learn⬙ or ⬙smart⬙ button. This can usually be found where the hanging antenna wire is attached to the motor-head unit.

2. Firmly press and release the ⬙learn⬙ or ⬙smart⬙ button. (The name and color of the button may vary by manu- facturer.) NOTE: There are 30 seconds in which to initiate Step Three. 3. Return to the vehicle and firmly press, hold for two seconds and release the programmed HomeLink button. Repeat the ⴖpress/hold/releaseⴖ sequence a second time, and, depending on the brand of the garage door opener (or other rolling code equipped device), repeat this sequence a third time to complete the programming. HomeLink should now activate your equipped device. NOTE: To program the remaining two HomeLink but- tons, begin with ⬙Programming⬙ Step Two. Do not repeat Step One. For questions or comments, please contact HomeLink at www.homelink.com or 1-800-355-3515.

rolling code

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 179

Canadian Programming/Gate Programming Canadian radio-frequency laws require transmitter sig- nals to ⬙time-out⬙ (or quit) after several seconds of transmission which may not be long enough for HomeLink to pick up the signal during programming. Similar to this Canadian law, some U.S. gate operators are designed to ⬙time-out⬙ in the same manner. If you live in Canada or you are having difficulties programming a gate operator by using the ⬙Program- ming⬙ procedures (regardless of where you live), replace ⴖProgramming HomeLinkⴖ Step Three with the follow- ing: If programming a garage door opener or gate NOTE: operator, it is advised to unplug the device during the ⬙cycling⬙ process to prevent possible overheating. 3. Continue to press and hold the HomeLink button while you press and release every two seconds ⬙cycle⬙ your hand-held transmitter until the frequency signal has

180 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

successfully been accepted by HomeLink. (The indicator light will flash slowly and then rapidly.) Proceed with ⬙Programming⬙ Step Four to complete. Using HomeLink To operate, simply press and release the programmed HomeLink button. Activation will now occur for the trained device (i.e. garage door opener, gate operator, security system, entry door lock, home/office lighting, etc.). For convenience, the hand-held transmitter of the device may also be used at any time. In the event that there are still programming difficulties or questions, contact HomeLink at: www.homelink.com or 1-800-355- 3515. Erasing HomeLink Buttons To erase programming from the three buttons (individual buttons cannot be erased but can be ⬙reprogrammed⬙ - note below), follow the step noted:

• Press and hold the two outer HomeLink buttons until the indicator light begins to flash-after 20 seconds. Release both buttons. Do not hold for longer that 30
seconds. HomeLink is now in the train (or learning) mode and can be programmed at any time beginning with ⬙Programming⬙ - Step Two.

Reprogramming a Single HomeLink Button To program a device to HomeLink using a HomeLink button previously trained, follow these steps: 1. Press and hold the desired HomeLink button. Do NOT release the button. 2. The indicator light will begin to flash after 20 seconds. Without releasing the HomeLink button, proceed with ⬙Programming⬙ Step Two. For questions or comments, contact HomeLink at: www.homelink.com or 1-800-355-3515.

Security If you sell your vehicle, be sure to erase the frequencies by following the “Erasing HomeLink Buttons” instruc- tions in this section. This device complies with part 15 of FCC rules and with RSS-210 of Industry Canada. Operation is subject to the following conditions: • This device may not cause harmful interference. • This device must accept any interference that may be received including interference that may cause undes- ired operation.

NOTE: Changes or modifications not expressly ap- proved by the party responsible for compliance could void the user’s authority to operate the equipment. HomeLink威 is a trademark owned by Johnson Controls, Inc.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 181

In the event that you are still having programming difficulties, questions, or comments, contact HomeLink at: www.homelink.com or 1-800-355-3515.

POWER SUNROOF — IF EQUIPPED The power sunroof control is located between the sun visors on the overhead console.

Power Sunroof Controls

182 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Press and hold the switch rearward to fully open the sunroof. The sunroof can be stopped at any position between closed and full open. Momentarily pressing the switch rearward will activate the Express Open Feature, causing the sunroof to open automatically. Press and hold the button located to the right of the sunroof switch, to open the vent. The sunroof can be stopped at any position between closed and full vent. To close the sunroof from the vent position, press and hold the switch forward. Releasing the switch will stop the movement of the sunroof and the sunroof will remain in the partial vent position until the switch is pushed forward again. Express Open Feature During the Express Open operation, any movement of the switch will stop the sunroof and it will remain in a partial open position. Again, momentarily pressing the switch rearward will activate the Express Open Feature.

To close the sunroof, hold the switch in the forward position. Again, any release of the switch will stop the movement and the sunroof will remain in a partial open condition until the switch is pushed forward again. The sunshade can be opened manually. It will also open as the sunroof opens. The sunshade cannot be closed if the sunroof is open.

WARNING!

NEVER leave children alone in a vehicle. Occupants, particularly unattended children, can become en- trapped by the power sunroof while operating the power sunroof switch. Such entrapment may result in serious injury or death. Don’t leave the keys in the ignition. A child could operate power windows, other controls, or move the vehicle

WARNING!

In an accident, there is a greater risk of being thrown from a vehicle with an open sunroof. You could also be seriously injured or killed. Always fasten your seat belt properly and make sure all passengers are properly secured too. Do not allow small children to operate the sunroof. Never allow fingers or other body parts, or any object to project through the sunroof opening. Injury may result.

Wind Buffeting Wind buffeting can be described as the perception of pressure on the ears or a helicopter type sound in the ears. Your vehicle may exhibit wind buffeting with the windows down, or the sunroof (if equipped) in certain open or partially open positions. This is a normal occur- rence and can be minimized. If the buffeting occurs with

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 183

the rear windows open, open the front and rear windows together to minimize the buffeting. If the buffeting occurs with the sunroof open, adjust the sunroof opening to minimize the buffeting or open any window. Sunroof Maintenance Use only a non-abrasive cleaner and a soft cloth to clean the glass panel.

ELECTRICAL POWER OUTLETS — IF EQUIPPED To the left of the instrument panel cup holder are two 12
volt power outlets. The upper outlet is controlled by the ignition switch and the lower outlet is connected directly to the battery. The upper outlet will also operate a conventional cigar lighter unit (if equipped with an optional Smoker’s Package). A third outlet is located on the driver’s side, just to the rear of the sliding door and is also controlled by the ignition switch. The lower and rear outlets will not accommodate a conventional cigar lighter unit.

184 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

The lower outlet is protected by an automatic reset circuit breaker. The automatic circuit breaker restores power when the overload is removed. The circuit breaker also supplies power to the outlet in the removable floor console, when in the front position. Refer to section 3
“Removable Floor Console” in this manual. If desired, all of the power outlets can be NOTE: converted by your authorized dealer to provide power with the ignition switch in the OFF position.

Rear Power Outlet

The outlets include tethered caps labeled with a key or battery symbol indicating the power source. The lower instrument panel outlet is powered directly from the battery, items plugged into this outlet may discharge the battery and/or prevent engine starting.

Electrical Outlet Use With Engine Off

CAUTION!

• Many accessories that can be plugged in draw power from

the vehicle’s battery, even when not in use (i.e. cellular phones, etc.). Eventually, if plugged in long enough, the vehicle’s battery will discharge sufficiently to degrade battery life and/or prevent engine starting.

• Accessories that draw higher power (i.e. coolers, vacuum

cleaners, lights, etc.), will degrade the battery even more quickly. Only use these intermittently and with greater caution.

• After the use of high power draw accessories, or long

periods of the vehicle not being started (with accessories still plugged in), the vehicle must be driven a sufficient length of time to allow the alternator to recharge the vehicle’s battery.

• Power outlets are designed for accessory plugs only. Do not

hang any type of accessory or accessory bracket from the plug. Improper use of the power outlet can cause damage.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 185

CONVENIENCE TRAY DRAWER AND CUP HOLDERS

Instrument Panel Cup Holders The instrument panel cupholders are located in a pull out drawer just below the climate controls.

Front Cupholders

186 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

When the drawer is pulled out firmly, the arms of the cupholders will spring out. Place the container to be held into one of the cupholders and then push the arm toward the container until the container is held stable. There are adjustable positions for the arm so the cupholder can accommodate a wide variety of container types and sizes, including those with handles. The arms of the cupholder can be adjusted in or out without damaging the detent mechanism. NOTE: Be sure the drawer is pulled out completely, otherwise the adjustable arm detents will not engage and the container will not be held stable. Convenience Tray And Optional Smoker’s Package Kit Located between the instrument panel cupholders is a convenience tray that has been designed to hold miscel- laneous small items.

NOTE: The convenience tray should never be used for ashes without the optional ash receiver in place. Perma- nent burn marks may result. With the optional dealer installed Smoker’s package, a removable ash receiver is inserted into the convenience tray location. To install the ash receiver, slide the forward edge into the convenience tray opening and push down to lock it into position. For cleaning of the ash receiver, its removal is accomplished by inserting the end of a key in the pry slot that is molded into the rear edge of the ash receiver and then twisting the key slightly.

Rear Cupholders There are dual stationary cupholders located in the passenger side rear trim panel and a single stationary cup holder on the driver side rear trim panel. There are also dual underseat cupholders for the 2nd seat passengers. With a bench seat in the 2nd seat position these cupholders slide out from under the center of the seat. If your vehicle is equipped with quad seats in the 2nd seat position, these cupholders are located on the out- board side of the seat pedestal.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 187

Quad Seat Cupholder

NOTE: • The quad seat cupholders will remain upright if the

seat is tilted forward.

188 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

• The quad seat cupholders are designed to break away if stepped on. To return the cupholder to its normal position, simply push the cupholder up to snap it into place. • The floor mat must be in position for optimum cup-

holder operation.

There are also two cupholders and a flat tray on the seat back of the quad seats. These can be used when the seat back is folded forward.

STORAGE

Front Seat Storage Bin — If Equipped The storage bin is located under the front passenger’s seat. If equipped with a lock, it can be locked with the ignition key.

Front Seat Storage Bin

Second Row Seat Storage bins — If Equipped The Seat Storage Bins are located on the floor in front of the second row seats, the area below the covers can be used for storage when the second row seat is in the upright position.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 189

CAUTION!

NOTE: The storage bin cover must be locked and flat to avoid damage from contact with the front seat tracks, which have minimal clearance to the cover.

WARNING!

In an accident, serious injury could result if the seat storage bin covers are not properly latched. Do not drive the vehicle with the storage bin cover open. Keep the storage bin cover closed and latched while the vehicle is in motion. Do not operate the storage bin cover while the vehicle is in motion.

Storage Bin Cover Lock Release

Pull up on the storage bin latch to open the cover. Slide the storage bin locking mechanism to the ⬙Unlocked⬙ position to allow greater access to the storage bin.

190 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Overhead Rail System — If Equipped The overhead rail system contains provisions for three movable and removable overhead storage bins. The storage bins may be placed anywhere on the overhead rail system.

CAUTION!

Do not load objects over 1.5 lbs (0.68 kg) in the storage bins. Failure to follow this could cause damage to the Overhead Rail System.

To Remove Storage Bins 1. Support the bin with one hand and pull the latch handles out.

2. Twist the latch handles a 1⁄4 turn and pull outward to disengage the bin from the rail.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 191

twist a 1⁄4 turn to attach the bin to the rail. Push the latch handle down to lock the storage bin in place.

WARNING!

In a collision, you or others in your vehicle could be injured if the storage bins are not properly latched to the Overhead Rail System. Always be sure the storage bins are fully latched.

Removable Floor Console With Stow ’n Go Seating — If Equipped The removable floor console has a two power outlets, storage tray, light, removable cell phone holder, tissue holder, pen holder and a map holder. It can be removed from the vehicle by pulling the release handle inside the floor console. To remove the console use the following procedure:

3. Remove the storage bin. NOTE: Make sure the latch handle pops out before removing the storage bin. To reinstall the storage bins, place the bin in the desired location on the overhead rail, push firmly upward on the bin with one hand, while pushing in on the latch handle,

192 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

1. Open the console lid and remove the storage tray. 2. Pull up on the release handle located inside the floor console, and slide the console rearward to disengage from the floor.

Stow ’n Go Center Console Release Handle

3. Remove the floor console.

To reinstall the console, open the console lid and remove the storage tray. Pull up on the release handle and slide the console forward to engage the front of the console into the floor tray. Pivot the floor console down until it is seated on the floor tray and release the handle. Pull up on the console to be sure it is firmly attached.

WARNING!

In an accident, serious injury could result if the removable floor console is not properly installed. Always be sure the removable floor console is fully latched.

Cell Phone Holder Removal 1. Open the floor console lid and lift the cell phone holder upward.

2. Squeeze the legs together to disengage the holder from the floor console and remove the cell phone holder. To reinstall the cell phone holder, align the pivot legs into the guides and push forward to snap the legs into place. Removable Floor Console Without Stow ’n Go Seating — If Equipped The removable floor console has a power outlet, storage tray, light, cell phone holder, tissue holder, and a map holder. It can be placed between either the front seats or middle seats. NOTE: When the console is located between the front seats the outlet is protected by an automatic circuit breaker and is powered directly from the battery, items plugged into this outlet may discharge the battery and/or prevent engine starting.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 193

Removable Floor Console

To remove the console use the following procedure: 1. Open the rear lid and remove the storage tray. 2. Pull up on the release handle located inside the floor console to disengage the floor console, reinstall the storage tray and close the rear lid.

194 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Removable Floor Console Release Handle

3. Using the front and rear grab handles, slide the console rearward to disengage the front of the console and lift up to remove the console from the floor. 4. Place the rubber mat on the floor tray.

To reinstall the console, remove the rubber mat and relocate to the alternate floor tray, slide the console forward to engage the front of the console into the floor tray. Rapidly push down on the rear of the console with enough force to engage the latch, you should hear the latch “snap” into place. Pull up on the console to be sure it is firmly attached.

WARNING!

In an accident, serious injury could result if the removable floor console is not properly installed. Always be sure the removable floor console is fully latched.

NOTE: When the removable floor console is located between the middle seats, the power outlet only has power supplied to it when the ignition switch is ON.

Cell Phone Holder 1. Open the front lid and remove the cell phone holder by pulling rearward and up on the lower edge of the holder.

2. Plug in the power cord for the cellular phone into the outlet located in the bottom of the forward console bin and reinstall the cell phone holder. 3. Place the cell phone into the holder.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 195

Cell Phone Holder

196 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

CAUTION!

• Many accessories that can be plugged in draw power from the vehicle’s battery, even when not in use (i.e. cellular phones, etc.). Eventually, if plugged in long enough, the vehicle’s battery will discharge sufficiently to degrade battery life and/or prevent engine starting. • Accessories that draw higher power (i.e. coolers, vacuum cleaners, lights, etc.), will degrade the battery even more quickly. Only use these inter- mittently and with greater caution. • After the use of high power draw accessories, or long periods of the vehicle not being started (with accessories still plugged in), the vehicle must be driven a sufficient length of time to allow the generator to recharge the vehicle’s battery.

Rear Compartment Storage Bins Your vehicle may be equipped with open storage bins located in each rear trim panel. Cargo/Tub Nets Two cargo/tub nets are available on vehicles equipped with Stow ’n Go Seating. The cargo nets fit in the second row storage bin and the third row tub. The nets are supported by hooks located in these areas. Refer to instructions provided in the net kit. Coat Hooks Coat hooks are located along the headliner for the second and third row seating positions. The coat hook load limit is 10 lbs (4.5 kg). Exceeding the recommended load limit can cause the coat hooks to break or disengage from the vehicle.

Cargo Area Storage The seats in your vehicle are in-line which enables you to stow long objects, such as lumber or skis, on the floor without moving the seats. NOTE: With all rear seat backs folded, a 4 x 8 foot sheet of building material may be stored in the long-wheelbase body style on top of the folded seats with the liftgate closed. The front seats must be moved slightly forward of the rearmost position. If the rear seats are removed no front seat adjustment is needed and more than one 4 x 8
sheet of building material may be stored. The liftgate sill plate has a raised line with the statement “Load To This Line”. This line indicates how far rearward cargo can be placed without interfering with liftgate closing.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 197

Rear Cargo Area Loading Limit

ROOF LUGGAGE RACK — IF EQUIPPED The crossbars and siderails are designed to carry the weight on vehicles equipped with a luggage rack. The load must not exceed 68 kg (150 lbs), and should be uniformly distributed over the luggage rack crossbars.

198 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Roof Rack

Distribute cargo weight evenly on the roof rack crossbars. The roof rack does not increase the total load carrying capacity of the vehicle. Be sure the total load of cargo inside the vehicle plus that on the external rack does not exceed the maximum vehicle load capacity.

To move the cross bars, loosen the thumb screws located at the upper edge of each cross bar approximately six turns, then move the cross bar to the desired position, keeping the crossbars parallel to the rack frame. Once the cross bar is in place, retighten the thumb screws to lock the cross bar into position. Attempt to move the crossbar again to ensure that it has properly locked into position. NOTE: To help control wind noise when installing the cross bars make sure that the arrows marked on the front side of the cross bars are facing the front of the vehicle. Also, when the cross bars are not in use the notch on the cross bars should be aligned with the arrows on the side rails. This will help reduce the amount of wind noise when the crossbars are not in use. The tie down holes on the cross bar ends should always be used to tie down the load. Check the straps frequently to be sure that the load remains securely attached.

CAUTION!

WARNING!

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 199

• Crossbars should remain equally spaced or parallel at any

luggage rack position for proper function. Noncompliance could result in damage to the luggage rack, cargo and/or vehicle.

• To avoid damage to the roof rack and vehicle, do not exceed

the maximum roof rack load capacity of 150 lbs (68 kg). Always distribute heavy loads as evenly as possible and secure the load appropriately.

• Long loads which extend over the windshield, such as

wood panels or surfboards, or loads with large frontal area should be secured to both the front and rear of the vehicle.

• Travel at reduced speeds and turn corners carefully when

carrying large or heavy loads on the roof rack. Wind forces, due to natural causes or nearby truck traffic, can add sudden upward lift to loads. This is especially true on large flat loads and may result in damage to the cargo or your vehicle.

Cargo must be securely tied before driving your vehicle. Improperly secured loads can fly off the vehicle, particularly at high speeds, resulting in personal injury or property damage. Follow the Roof Rack Cautions when carrying cargo on your roof rack.

LOAD LEVELING SYSTEM The automatic load leveling system will provide a level riding vehicle under most passenger and cargo loading conditions. A hydraulic pump contained within the shock absorbers raises the rear of the vehicle to the correct height. It takes approximately 1 mile (1.6 km) of driving for the leveling to complete depending on road surface conditions.

200 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

If the leveled vehicle is not moved for approximately 15
hours, the leveling system will bleed itself down. The vehicle must be driven to reset the system.

WARNING!

Do not install the load leveling system on vehicles that are not equipped with Anti-Lock Brakes. Ve- hicles without Anti-Lock Brakes (ABS) have a height-sensing proportioning valve. Installing a lev- eling system will render this system ineffective, inappropriately reducing rear brake pressure, result- ing in increased stopping distances. You could have an accident.

UNDERSTANDING YOUR INSTRUMENT PANEL

CONTENTS

䡵 Instrument Panels And Controls . . . . . . . . . . . . 206
䡵 Base Instrument Cluster . . . . . . . . . . . . . . . . . . 207
䡵 Instrument Cluster With Tach . . . . . . . . . . . . . . 208
䡵 Premium Instrument Cluster . . . . . . . . . . . . . . . 209
䡵 Instrument Cluster Descriptions . . . . . . . . . . . . 210
䡵 Electronic Digital Clock . . . . . . . . . . . . . . . . . . 219
▫ Clock Setting Procedure . . . . . . . . . . . . . . . . . 219
䡵 Radio General Information . . . . . . . . . . . . . . . . 219
▫ Radio Broadcast Signals . . . . . . . . . . . . . . . . . 219

▫ Two Types Of Signals . . . . . . . . . . . . . . . . . . 220
▫ Electrical Disturbances . . . . . . . . . . . . . . . . . . 220
▫ AM Reception . . . . . . . . . . . . . . . . . . . . . . . 220
▫ FM Reception . . . . . . . . . . . . . . . . . . . . . . . . 220

䡵 Sales Code RAZ — AM/ FM Stereo Radio With

Cassette Tape Player, CD Player And CD Changer Controls . . . . . . . . . . . . . . . . . . . . . . . 221
▫ Operating Instructions — Radio . . . . . . . . . . . 221
▫ Power Switch, Volume Control . . . . . . . . . . . . 221
▫ Seek Button (Radio Mode) . . . . . . . . . . . . . . . 221

202 UNDERSTANDING YOUR INSTRUMENT PANEL

▫ Tuning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 222
▫ Radio Data System (RDS) . . . . . . . . . . . . . . . 222
▫ PTY (Program Type) Button . . . . . . . . . . . . . . 222
▫ Balance . . . . . . . . . . . . . . . . . . . . . . . . . . . . 224
▫ Fade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 224
▫ Tone Control . . . . . . . . . . . . . . . . . . . . . . . . 224
▫ AM/FM Selection . . . . . . . . . . . . . . . . . . . . . 224
▫ Scan Button . . . . . . . . . . . . . . . . . . . . . . . . . 224
▫ To Set The Radio Push-Button Memory . . . . . . 225
▫ To Change From Clock To Radio Mode . . . . . . 225
▫ Operating Instructions — Tape Player . . . . . . . 225
▫ Seek Button . . . . . . . . . . . . . . . . . . . . . . . . . 225
▫ Fast Forward (FF) . . . . . . . . . . . . . . . . . . . . . 226

▫ Rewind (RW) . . . . . . . . . . . . . . . . . . . . . . . . 226
▫ Tape Eject . . . . . . . . . . . . . . . . . . . . . . . . . . . 226
▫ Scan Button . . . . . . . . . . . . . . . . . . . . . . . . . 226
▫ Changing Tape Direction . . . . . . . . . . . . . . . . 226
▫ Metal Tape Selection . . . . . . . . . . . . . . . . . . . 226
▫ Pinch Roller Release . . . . . . . . . . . . . . . . . . . 227
▫ Noise Reduction . . . . . . . . . . . . . . . . . . . . . . 227
▫ Operating Instructions — CD Player . . . . . . . . 227
▫ Inserting The Compact Disc . . . . . . . . . . . . . . 227
▫ Seek Button . . . . . . . . . . . . . . . . . . . . . . . . . 228
▫ EJT CD (Eject) Button . . . . . . . . . . . . . . . . . . 228
▫ FF/Tune/RW . . . . . . . . . . . . . . . . . . . . . . . . 229
▫ Program Button 4 (Random Play) . . . . . . . . . . 229

▫ Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 229
▫ Tape CD Button . . . . . . . . . . . . . . . . . . . . . . 229
▫ Time Button . . . . . . . . . . . . . . . . . . . . . . . . . 230
▫ Scan Button . . . . . . . . . . . . . . . . . . . . . . . . . 230
▫ CD Changer Control Capability — If

Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . . 230

䡵 Sales Code REV — AM & FM Stereo Radio With

CD Player And CD/DVD Changer Controls . . . . 231
▫ Radio Operation . . . . . . . . . . . . . . . . . . . . . . 232
▫ CD Player Operation . . . . . . . . . . . . . . . . . . . 235
▫ CD/DVD Changer Operation . . . . . . . . . . . . . 237
▫ Notes On Playing MP3 Files . . . . . . . . . . . . . 237
▫ Operation Instructions - (CD Mode For MP3

Audio Play)

. . . . . . . . . . . . . . . . . . . . . . . . . 240

UNDERSTANDING YOUR INSTRUMENT PANEL 203

䡵 Sales Code RBQ — AM/FM Stereo Radio With

6 - Disc CD Changer . . . . . . . . . . . . . . . . . . . . 241
▫ Radio Operation . . . . . . . . . . . . . . . . . . . . . . 242
▫ CD Player Operation . . . . . . . . . . . . . . . . . . . 244

䡵 Sales Code RBK — AM/ FM Stereo Radio With

CD Player And CD Changer Controls . . . . . . . . 249
▫ Radio Operation . . . . . . . . . . . . . . . . . . . . . . 249
▫ CD Player Operation . . . . . . . . . . . . . . . . . . . 251
▫ CD Changer Control Capability — If

Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . . 253

䡵 Sales Code RB1 — AM/FM Stereo Radio With

DVD/GPS Navigation System . . . . . . . . . . . . . . 255
▫ Clock Setting Procedure . . . . . . . . . . . . . . . . . 256

䡵 6 Disc CD/DVD Changer (RDV) — If

Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . . . 257

204 UNDERSTANDING YOUR INSTRUMENT PANEL

▫ Operating Instructions — CD/DVD Changer . . 258
▫ Eject (EJT) Button . . . . . . . . . . . . . . . . . . . . . 260
▫ Remote Control Operating Instructions . . . . . . 260
▫ Operating Instructions — Video Screen . . . . . . 264
▫ Operating Instructions — Headphones . . . . . . 266
▫ Operating Instructions — MP3 Player, Portable

Walkman . . . . . . . . . . . . . . . . . . . . . . . . . . . 268

▫ Operating Instructions — Video

Games/Camcorders

. . . . . . . . . . . . . . . . . . . 268
䡵 Satellite Radio — If Equipped . . . . . . . . . . . . . . 268
▫ System Activation . . . . . . . . . . . . . . . . . . . . . 268
▫ Electronic Serial Number/Sirius Identification

Number (ENS/SID) . . . . . . . . . . . . . . . . . . . . 269

▫ Selecting Satellite Mode In RAH And RBK

Radios . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 269

▫ Selecting Satellite Mode In RBU, RAZ, RB1

And RBQ Radios

. . . . . . . . . . . . . . . . . . . . . 270
▫ Selecting a Channel . . . . . . . . . . . . . . . . . . . . 270
▫ Storing And Selecting Pre-Set Channels . . . . . . 271
▫ Using The PTY (Program Type) Button — If

Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . . 271
▫ PTY Button ⬙Scan⬙ . . . . . . . . . . . . . . . . . . . . . 271
▫ PTY Button ⬙Seek⬙ . . . . . . . . . . . . . . . . . . . . . 271
▫ Satellite Antenna . . . . . . . . . . . . . . . . . . . . . . 271
▫ Reception Quality . . . . . . . . . . . . . . . . . . . . . 272
䡵 Radio Operation And Cellular Phones . . . . . . . . 272
䡵 Remote Sound System Controls — If Equipped . . 272

▫ Radio Operation . . . . . . . . . . . . . . . . . . . . . . 273
▫ Tape Player . . . . . . . . . . . . . . . . . . . . . . . . . 274
▫ CD Player . . . . . . . . . . . . . . . . . . . . . . . . . . 274
䡵 Cassette Tape And Player Maintenance . . . . . . . 274
䡵 CD/DVD Disc Maintenance . . . . . . . . . . . . . . . 275
䡵 Climate Controls . . . . . . . . . . . . . . . . . . . . . . . 276

▫ Manual Air Conditioning And Heating

System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 276
▫ Front Mode Control . . . . . . . . . . . . . . . . . . . 277
▫ Manual Air Conditioning Operation . . . . . . . . 281
▫ Manual Rear Zone Climate Control — If

Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . . 284

▫ Automatic Temperature Control — If

Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . . 286

UNDERSTANDING YOUR INSTRUMENT PANEL 205

䡵 Rear Window Features . . . . . . . . . . . . . . . . . . . 298

▫ Intermittent Rear Wiper Operation — Manual

Temperature Control Only . . . . . . . . . . . . . . . 298

▫ Rear Washer Operation — Manual Temperature

Control Only . . . . . . . . . . . . . . . . . . . . . . . . 299

▫ Rear Wiper Operation — Automatic Temperature

Control Only . . . . . . . . . . . . . . . . . . . . . . . . 299

▫ Intermittent Rear Wiper Operation — Automatic

Temperature Control Only . . . . . . . . . . . . . . . 300
▫ Rear Washer Operation — Automatic Temperature Control Only . . . . . . . . . . . . . . . . . . . . . . . . 300

▫ Electric Rear Window Defroster — If

Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . . 301

206 UNDERSTANDING YOUR INSTRUMENT PANEL

INSTRUMENT PANELS AND CONTROLS

BASE INSTRUMENT CLUSTER

UNDERSTANDING YOUR INSTRUMENT PANEL 207

208 UNDERSTANDING YOUR INSTRUMENT PANEL

INSTRUMENT CLUSTER WITH TACH

PREMIUM INSTRUMENT CLUSTER

UNDERSTANDING YOUR INSTRUMENT PANEL 209

210 UNDERSTANDING YOUR INSTRUMENT PANEL

INSTRUMENT CLUSTER DESCRIPTIONS

1. Fuel Gauge The pointer shows the level of fuel in the fuel tank when the ignition switch is in the ON position. 2. Tire Pressure Monitoring Telltale Lamp — If Equipped

Each tire, including the spare (if provided), should be checked monthly when cold and inflated to the inflation pressure recommended by the vehicle manufacturer on the vehicle placard or tire inflation pressure label. (If your vehicle has tires of a different size than the size indicated on the vehicle placard or tire inflation pressure label, you should determine the proper tire inflation pressure for those tires.) As an added safety feature, your vehicle has been equipped with a Tire Pressure Monitoring System (TPMS) that illuminates a low tire pressure telltale when

one or more of your tires is significantly underinflated. Accordingly, when the low tire pressure telltale illumi- nates, you should stop and check your tires as soon as possible, and inflate them to the proper pressure. Driving on a significantly underinflated tire causes the tire to overheat and can lead to tire failure. Underinflation also reduces fuel efficiency and tire tread life, and may affect the vehicle’s handling and stopping ability. NOTE: The Tire Pressure Monitoring System (TPMS) is not a substitute for proper tire maintenance, and it is the driver’s responsibility to maintain correct tire pressure, even if underinflation has not reached the level to trigger illumination of the TPMS low tire pressure telltale. The Tire Pressure Monitoring Telltale Lamp will illumi- nate in the instrument cluster, and an audible chime will be activated when one or more tire pressures is low. The TPMS Telltale Lamp will flash on and off for 60 seconds

when a system fault is detected. The flash cycle will repeat every ten minutes or until the fault condition is removed and reset.

CAUTION!

The Tire Pressure Monitoring System (TPMS) has been optimized for the original equipment tires and wheels. TPMS pressures and warning have been established for the tire size equipped on your ve- hicle. Undesirable system operation or sensor dam- age may result when using replacement equipment that is not of the same size, type, and / or style. Aftermarket wheels can cause sensor damage. Do not use tire sealant from a can, or balance beads if your vehicle is equipped with a TPMS, as damage to the sensors may result.

UNDERSTANDING YOUR INSTRUMENT PANEL 211

3. Low Fuel Light

When the fuel level reaches approximately 3.0
gallons (11.0 liters) this light will turn on and remain on until fuel is added.

4. Turn Signal Indicators

The arrow will flash with the exterior turn signal when the turn signal lever is operated.

If the vehicle electronics sense that the vehicle has traveled about one mile with the turn signals on, a chime will sound to alert you to turn the signals off. If either indicator flashes at a rapid rate, check for a defective outside light bulb. 5. Liftgate Ajar

This light turns on if the liftgate is not com- pletely closed.

212 UNDERSTANDING YOUR INSTRUMENT PANEL

6. Door Ajar Light

This light turns on if a door is not completely closed.

7. Speedometer Indicates vehicle speed. 8. Brake System Warning Light

This light monitors various brake functions, including brake fluid level and parking brake application. If the brake light turns on, it may indicate that the parking brake is applied, there is a low brake fluid level or there is a problem with the anit-lock brake system. The dual brake system provides a reserve braking capac- ity in the event of a failure to a portion of the hydraulic system. Failure of either half of the dual brake system is indicated by the Brake Warning Light which will turn on when the brake fluid level in the master cylinder has dropped below a specified level.

The light will remain on until the cause is corrected. NOTE: The light may flash momentarily during sharp cornering maneuvers which change fluid level condi- tions. The vehicle should have service performed. If brake failure is indicated, immediate repair is neces- sary.

WARNING!

Driving a vehicle with the brake light on is danger- ous. Part of the brake system may have failed. It will take longer to stop the vehicle. You could have an accident. Have the vehicle checked immediately.

Vehicles equipped with Anti-Lock brakes (ABS), are also equipped with Electronic Brake Force Distribution (EBD).

In the event of an EBD failure, the Brake Warning Light will turn on along with the ABS Light. Immediate repair to the ABS system is required. The operation of the Brake Warning Light can be checked by turning the ignition switch from the OFF position to the ON position. The light should illuminate for approxi- mately four seconds. The light should then turn off unless the parking brake is applied or a brake fault is detected. If the light does not illuminate, have the light inspected by an authorized dealer. The light also will turn on when the parking brake is applied with the ignition switch in the ON position. NOTE: This light shows only that the parking brake is applied. It does not show the degree of brake application.

UNDERSTANDING YOUR INSTRUMENT PANEL 213

9. Airbag Light

This light turns on and remains on for 6 to 8
seconds as a bulb check when the ignition switch is first turned ON. If the light is not on during starting, stays on, or turns on while driving, have the system inspected by an authorized dealer as soon as possible. 10. Anti-Lock Light

This light monitors the Anti-Lock Brake Sys- tem. The light will turn on when the ignition switch is turned to the ON position and may stay on for as long as four seconds.

If the ABS light remains on or turns on while driving, it indicates that the Anti-Lock portion of the brake system is not functioning and that service is required. However, the conventional brake system will continue to operate normally if the BRAKE warning light is not on.

214 UNDERSTANDING YOUR INSTRUMENT PANEL

If the ABS light is on, the brake system should be serviced as soon as possible to restore the benefits of Anti-Lock brakes. If the ABS light does not turn on when the Ignition switch is turned to the ON position, have the light inspected by an authorized dealer. 11. Tachometer — If Equipped The red segments indicate the maximum permissible engine revolutions per minute (RPM x 1000) for each gear range. Before reaching the red area, ease up on the accelerator. 12. Voltage Light

This light monitors the electrical system voltage. The light should turn on momentarily as the engine is started. If the light stays on or turns on while driving, it indicates a problem with the charging system. Immediate service should be obtained.

13. Seat Belt Reminder Light

When the ignition switch is first turned ON, this light will turn on for 5 to 8 seconds as a bulb check. During the bulb check, if the driver’s and/or the occupied front passenger’s seat belt is unbuckled, a chime will sound. After the bulb check or when driving, if the driver’s and/or the occupied front passenger’s seat belt remains unbuckled, the Seat Belt Warning Light will flash or remain on continuously. Refer to ⬙Enhanced Driver Seat Belt Reminder System (BeltAlert™)⬙ in the Occupant Restraints section for more information. 14. Engine Temperature Warning Light

This light warns of an overheated engine condi- tion. If the engine is critically hot, a continuous chime will sound for 4 minutes. After the chime turns off, the engine will still be critically hot until the light turns off.

15. Vehicle Theft Alarm Light — If Equipped

This light will flash for approximately 15 sec- onds when the vehicle theft alarm is arming.

16. Temperature Gauge The temperature gauge shows engine coolant tempera- ture. Any reading within the normal range indicates that the engine cooling system is operating satisfactorily. The gauge pointer will likely indicate a higher tempera- ture when driving in hot weather, up mountain grades, or when towing a trailer. It should not be allowed to exceed the upper limits of the normal operating range.

UNDERSTANDING YOUR INSTRUMENT PANEL 215

CAUTION!

Driving with a hot engine cooling system could damage your vehicle. If temperature gauge reads “H“, pull over and stop the vehicle. Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range. If the pointer remains on the “H”, and you hear continuous chimes, turn the engine off immediately, and call for service.

216 UNDERSTANDING YOUR INSTRUMENT PANEL

WARNING!

A hot engine cooling system is dangerous. You or others could be badly burned by steam or boiling coolant. You may want to call a service center if your vehicle overheats. If you decide to look under the hood yourself, see Section 7 of this manual. Follow the warnings under the Cooling System Pressure Cap paragraph.

17. Washer Fluid Light

This light turns on when the washer fluid level falls below approximately 1/4 filled. The light will remain on until fluid is added.

18. Transmission Range Indicator This display indicator shows the automatic transaxle gear selection.

NOTE: You must apply the brakes before shifting from Park. 19. Oil Pressure Warning Light

This light shows low engine oil pressure. The light should turn on momentarily when the engine is started. If the light turns on while driving, stop the vehicle and shut off the engine as soon as possible. A chime will sound for 4 minutes when this light turns on. Do not operate the vehicle until the cause is corrected. This light does not show how much oil is in the engine. The engine oil level must be checked under the hood. 20. High Beam Light

This light shows that the headlights are on high beam. Pull lever towards the steering wheel to switch the headlights from high or low beam.

the turn signal

21. Malfunction Indicator Light

This light is part of an onboard diagnostic system called OBD that monitors engine and automatic transmission control systems. The light will illu- minate when the key is in the ON position before engine start. If the bulb does not come when turning the key from OFF to ON, have the condition checked promptly. Certain conditions such as a loose or missing gas cap, poor fuel quality, etc. may illuminate the light after engine start. The vehicle should be serviced if the light stays on through several of your typical driving cycles. In most situations the vehicle will drive normally and will not require towing. The Malfunction Indicator Light flashes to alert to serious conditions that could lead to immediate loss of power or severe catalytic converter damage. The vehicle should be serviced as soon as possible if this occurs.

UNDERSTANDING YOUR INSTRUMENT PANEL 217

22. Trac Off Indicator — If Equipped This display indicator should illuminate for approxi- mately four seconds as a bulb check when the ignition switch is first turned ON. The “TRAC OFF” Indicator will flash if the traction control is in use. The “TRAC OFF” Indicator will illuminate if: • The Traction Control switch has been used to turn • There is a Traction Control System malfunction • The system has been deactivated to prevent damage to the brake system due to overheated brake tem- peratures.

the system OFF.

NOTE: Extended heavy use of Traction Control may cause the system to deactivate and turn on the TRAC and the OFF indicators located in the instrument cluster.

218 UNDERSTANDING YOUR INSTRUMENT PANEL

This is to prevent overheating of the brake system and is a normal condition. The system will remain disabled for about 4 minutes until the brakes have cooled. The system will automatically reactivate and turn off the TRAC and the OFF indicators. If your vehicle becomes stuck in mud, ice, or snow, turn the Traction Control System OFF before attempting to “rock” the vehicle free. 23. Odometer/Trip Odometer The odometer shows the total distance the vehicle has been driven. U.S. federal regulations require that upon transfer of vehicle ownership, the seller certify to the purchaser the correct mileage that the vehicle has been driven. There- fore, if the odometer reading is changed during repair or replacement, be sure to keep a record of the reading before and after the service so that the correct mileage can be determined.

The trip odometer shows individual trip mileage. To switch from odometer to trip odometer, press the Trip Odometer button. Loose Fuel Filler Cap If the vehicle diagnostic system determines that the fuel filler cap is loose, improperly installed, or damaged, GASCAP will be displayed in the instrument cluster odometer. Tighten the fuel filler cap properly and press the odometer reset button to turn the GASCAP message off. If the problem continues, the message will appear the next time the vehicle is started. See Section 7 of this manual for more information. 24. Cruise Indicator This display indicator shows that the Speed Control System is ON.

25. Trip Odometer Button Press this button to change the display from odometer to trip odometer. The word TRIP will appear when in the trip odometer mode. Push in and hold the button for two seconds to reset the trip odometer to 0 miles or kilometers. The odometer must be in trip mode to reset.

ELECTRONIC DIGITAL CLOCK

UNDERSTANDING YOUR INSTRUMENT PANEL 219

Clock Setting Procedure

1. Turn the ignition switch to the ON or ACC position and press the time button. Using the tip of a ballpoint pen or similar object, press either the hour (H) or minute (M) buttons on the radio. 2. Press the H button to set hours or the M button to set minutes. The time setting will increase each time you press a button.

The clock and radio each use the display panel built into the radio. A digital readout shows the time in hours and minutes whenever the ignition switch is in the ON or ACC position and the time button is pressed. When the ignition switch is in the OFF position, or when the radio frequency is being displayed, time keeping is accurately maintained.

RADIO GENERAL INFORMATION

Radio Broadcast Signals Your new radio will provide excellent reception under most operating conditions. Like any system, however, car radios have performance limitations, due to mobile op- eration and natural phenomena, which might lead you to believe your sound system is malfunctioning. To help

220 UNDERSTANDING YOUR INSTRUMENT PANEL

you understand and save you concern about these “ap- parent” malfunctions, you must understand a point or two about the transmission and reception of radio sig- nals. Two Types of Signals There are two basic types of radio signals... AM or Amplitude Modulation, in which the transmitted sound causes the amplitude, or height, of the radio waves to vary... and FM or Frequency Modulation, in which the frequency of the wave is varied to carry the sound. Electrical Disturbances Radio waves may pick up electrical disturbances during transmission. They mainly affect the wave amplitude, and thus remain a part of the AM reception. They interfere very little with the frequency variations that carry the FM signal.

AM Reception AM sound is based on wave amplitude, so AM reception can be disrupted by such things as lightning, power lines and neon signs. FM Reception Because FM transmission is based on frequency varia- tions, interference that consists of amplitude variations can be filtered out, leaving the reception relatively clear, which is the major feature of FM radio. NOTE: The radio, steering wheel radio controls (if equipped), and 6 disc CD/DVD changer (if equipped) will remain active for up to 10 minutes after the ignition switch has been turned off. Opening a vehicle front door will cancel this feature.

SALES CODE RAZ — AM/ FM STEREO RADIO WITH CASSETTE TAPE PLAYER, CD PLAYER AND CD CHANGER CONTROLS

NOTE: The radio sales code is located on the lower left side of your radio faceplate.

RAZ Radio

UNDERSTANDING YOUR INSTRUMENT PANEL 221

Operating Instructions — Radio

NOTE: Power to operate the radio is controlled by the ignition switch. It must be in the ON or ACC position to operate the radio. Power Switch, Volume Control Press the ON/VOL control to turn the radio on. Turn the volume control clockwise to increase the volume. The volume will be displayed and continuously updated while the button is pressed. Seek Button (Radio Mode) Press and release the Seek button to search for the next station in either the AM or FM mode. Press the top of the button to seek up and the bottom to seek down. Holding the button will by pass stations until you release the button.

222 UNDERSTANDING YOUR INSTRUMENT PANEL

Tuning Press the TUNE control up or down to increase or decrease the frequency. If you press and hold the button, the radio will continue to tune until you release the button. The frequency will be displayed and continu- ously updated while the button is pressed. Radio Data System (RDS)

The Radio Data System allows radio broadcasting sta- tions to send data signals on a subcarrier frequency which is added to the stereo signal. RDS was developed to give FM receivers user-friendly features, such as Program Service name (PS) and Program Type (PTY). Program Service name is typically used by the broad- caster to display the station’s name or call letters, for example ⬙WNIC⬙. Typically these are 8 characters in length and are displayed by the radio for those stations

which are broadcasting this information. PTY (Program Type) is used to characterize the station’s program ma- terial, for example ⬙Rock Music⬙. PTY (Program Type) Button Pressing this button once will turn on the PTY mode for 5 seconds. If no action is taken during the 5 second time out the PTY icon will turn off. Pressing the PTY button within 5 seconds will allow the program format type to be selected. Many radio stations do not currently broad- cast PTY information. Toggle the PTY button to select the following format types:

Program Type

Radio Display

Adult Hits Classical Classic Rock College

Adult Hits Classical Classic Rock College

Program Type

Country Information Jazz Foreign Language News Nostalgia Oldies Personality Public Rhythm and Blues Religious Music Religious Talk Rock