2006 Chevrolet Monte Carlo Owners Manual

Download PDF Manual
15 seconds between each try to help avoid draining your battery or damaging your starter. 2. If your vehicle does not start within 10 seconds, hold the key in START for about 10 seconds at a time until the engine starts. Wait about 15 seconds between each try. 2-19 3. If the engine still will not start, or starts but then stops, it could be ﬂooded with too much gasoline. Try pushing your accelerator pedal all the way to the ﬂoor and holding it there as you hold the key in START for about three seconds. If the vehicle starts brieﬂy but then stops again, do the same thing. This time keep the pedal down for ﬁve or six seconds to clear the extra gasoline from the engine. After waiting about 15 seconds, repeat the normal starting procedure. Notice: Your engine is designed to work with the electronics in your vehicle. If you add electrical parts or accessories, you could change the way the engine operates. Before adding electrical equipment, check with your dealer. If you do not, your engine might not perform properly. Any resulting damage would not be covered by your vehicle’s warranty. Engine Coolant Heater Your vehicle may have this feature. In very cold weather, 0°F (−18°C) or colder, the engine coolant heater can help. You will get easier starting and better fuel economy during engine warm-up. Usually, the coolant heater should be plugged in a minimum of four hours prior to starting your vehicle. At temperatures above 32°F (0°C), use of the coolant heater is not required. To Use the Engine Coolant Heater 1. Turn off the engine. 2. Open the hood and unwrap the electrical cord. The cord is attached to the underside of the diagonal brace, which is located above the engine air cleaner/ﬁlter assembly. 3. Plug it into a normal, grounded 110-volt AC outlet. 2-20 Displacement on Demand™ (DoD™) (5.3L V8 Engine) Your vehicle’s engine may be equipped with Displacement on Demand™ (DoD™). This system allows the engine to operate on either all or half of its cylinders, depending on your driving conditions. When less power is required, such as cruising at a constant vehicle speed, the system will operate in the half cylinder mode, allowing your vehicle to achieve better fuel economy. When greater power demands are required, such as accelerating from a stop, passing, or merging onto a freeway, the system will maintain full-cylinder operation. {CAUTION: Plugging the cord into an ungrounded outlet could cause an electrical shock. Also, the wrong kind of extension cord could overheat and cause a ﬁre. You could be seriously injured. Plug the cord into a properly grounded three-prong 110-volt AC outlet. If the cord will not reach, use a heavy-duty three-prong extension cord rated for at least 15 amps. 4. Before starting the engine, be sure to unplug and store the cord as it was before to keep it away from moving engine parts. If you do not, it could be damaged. How long should you keep the coolant heater plugged in? The answer depends on the outside temperature, the kind of oil you have, and some other things. Instead of trying to list everything here, we ask that you contact your dealer in the area where you will be parking your vehicle. The dealer can give you the best advice for that particular area. 2-21 Automatic Transaxle Operation Your automatic transaxle has a shift lever on the console between the seats. {CAUTION: It can be dangerous to get out of your vehicle if the shift lever is not fully in PARK (P) with the parking brake ﬁrmly set. Your vehicle can roll. If you have left the engine running, the vehicle can move suddenly. You or others could be injured. To be sure your vehicle will not move, even when you are on fairly level ground, use the steps that follow. If you are pulling a trailer, see Towing a Trailer on page 4-36. Make sure the shift lever is fully in PARK (P) before starting the engine. Your vehicle has an automatic transaxle shift lock control system. You must fully apply your regular brakes before you can shift from PARK (P) while the ignition is in RUN. If you cannot shift out of PARK (P), ease pressure on the shift lever by pushing it all the way into PARK (P) while keeping the brake pedal pushed down. Release the shift lever button if you have a console shift. Then move the shift lever out of PARK (P). See Shifting Out of Park (P) on page 2-27. There is a display, located on the instrument panel cluster that will indicate the gear the vehicle is in. Maximum engine speed is limited on automatic transaxle vehicles while you are in PARK (P) or NEUTRAL (N) to protect driveline components from improper operation. There are several different positions for the shift lever. PARK (P): This position locks your front wheels. It is the best position to use when the engine is started because your vehicle cannot move easily. 2-22 REVERSE (R): Use this gear to back up. Notice: Shifting to REVERSE (R) while your vehicle is moving forward could damage the transaxle. The repairs would not be covered by your warranty. Shift to REVERSE (R) only after your vehicle is stopped. To rock your vehicle back and forth to get out of snow, ice or sand without damaging your transaxle, see If Your Vehicle is Stuck in Sand, Mud, Ice or Snow on page 4-28. NEUTRAL (N): In this position, your engine does not connect with the wheels. To restart when you are already moving, use NEUTRAL (N) only. Also, use NEUTRAL (N) when your vehicle is being towed. {CAUTION: Shifting into a drive gear while your engine is running at high speed is dangerous. Unless your foot is ﬁrmly on the brake pedal, your vehicle could move very rapidly. You could lose control and hit people or objects. Do not shift into a drive gear while your engine is running at high speed. Notice: Shifting out of PARK (P) or NEUTRAL (N) while the engine is running at high speed may damage the transaxle. The repairs would not be covered by your warranty. Be sure the engine is not running at high speeds when shifting your vehicle. AUTOMATIC OVERDRIVE (D): This position is for normal driving. If you need more power for passing, and you are: (cid:127) Going less than 35 mph (55 km/h), push the accelerator pedal about halfway down. (cid:127) Going about 35 mph (55 km/h) or more, push the accelerator pedal all the way down. If your vehicle seems to start up rather You will shift down to the next gear and have more power. Notice: slowly or not shift gears when you go faster, and you continue to drive your vehicle that way, you could damage the transaxle. Have your vehicle serviced right away. You can drive in SECOND (2) when you are driving less than 35 mph (55 km/h) and AUTOMATIC OVERDRIVE (D) for higher speeds until then. 2-23 FIRST (1): This position gives you even more power, but lower fuel economy than SECOND (2). You can use it on very steep hills, or in deep snow or mud. If the shift lever is in FIRST (1), the transaxle will not shift into ﬁrst gear until the vehicle is going slowly enough. Notice: Spinning the tires or holding the vehicle in one place on a hill using only the accelerator pedal may damage the transaxle. If you are stuck, do not spin the tires. When stopping on a hill, use the brakes, or parking brake to hold the vehicle in place. THIRD (3): This position is also used for normal driving, but it offers more power and lower fuel economy than AUTOMATIC OVERDRIVE (D). Here are some times you might choose THIRD (3) instead of AUTOMATIC OVERDRIVE (D): (cid:127) When driving on hilly, winding roads (cid:127) When towing a trailer, so there is less shifting between gears (cid:127) When going down a steep hill. For more information, see Hill and Mountain Roads on page 4-22. SECOND (2): This position gives you more power but lower fuel economy than THIRD (3). You can use SECOND (2) on hills. It can help control your speed as you go down steep mountain roads. You would also then want to use your brakes off and on. Notice: Driving in SECOND (2) for more than 25 miles (40 km) or at speeds over 55 mph (90 km/h) may damage the transaxle. Also, shifting into SECOND (2) at speeds above 65 mph (105 km/h) can cause damage. Drive in THIRD (3) or AUTOMATIC OVERDRIVE (D) instead of SECOND (2). 2-24 Parking Brake The parking brake is located to the left of the brake pedal, near the driver’s door. To set the parking brake, hold the brake pedal down with your right foot. Push down the parking brake pedal with your left foot. To release the parking brake, hold the brake pedal down with your right foot and push the parking brake pedal with your left foot. When you lift your left foot, the parking brake pedal will follow it to the released position. A warning chime will sound and a brake warning light located on the instrument panel cluster will come on, if the parking brake is set, the ignition is on and the shift lever is not in PARK (P). Notice: Driving with the parking brake on can overheat the brake system and cause premature wear or damage to brake system parts. Verify that the parking brake is fully released and the brake warning light is off before driving. If you are towing a trailer and parking on any hill, see Towing a Trailer on page 4-36. 2-25 Shifting Into Park (P) {CAUTION: It can be dangerous to get out of your vehicle if the shift lever is not fully in PARK (P) with the parking brake ﬁrmly set. Your vehicle can roll. If you have left the engine running, the vehicle can move suddenly. You or others could be injured. To be sure your vehicle will not move, even when you are on fairly level ground, use the steps that follow. If you are pulling a trailer, see Towing a Trailer on page 4-36. 1. Hold the brake pedal down with your right foot and set the parking brake. 2. Move the shift lever into PARK (P) by holding in the button on the shift lever and pushing the shift lever all the way toward the front of the vehicle. 3. Turn the ignition key to OFF. 4. Remove the key and take it with you. If you can leave your vehicle with the ignition key in your hand, your vehicle is in PARK (P). 2-26 Leaving Your Vehicle With the Engine Running {CAUTION: It can be dangerous to leave your vehicle with the engine running. Your vehicle could move suddenly if the shift lever is not fully in PARK (P) with the parking brake ﬁrmly set. And, if you leave the vehicle with the engine running, it could overheat and even catch ﬁre. You or others could be injured. Do not leave your vehicle with the engine running. If you have to leave your vehicle with the engine running, be sure your vehicle is in PARK (P) and your parking brake is ﬁrmly set before you leave it. After you have moved the shift lever into PARK (P), hold the regular brake pedal down. Then, see if you can move the shift lever away from PARK (P) without ﬁrst pushing the button. If you can, it means that the shift lever was not fully locked in PARK (P). Torque Lock If you are parking on a hill and you do not shift your transaxle into PARK (P) properly, the weight of the vehicle may put too much force on the parking pawl in the transaxle. You may ﬁnd it difficult to pull the shift lever out of PARK (P). This is called torque lock. To prevent torque lock, set the parking brake and then shift into PARK (P) properly before you leave the driver’s seat. To ﬁnd out how, see Shifting Into Park (P) on page 2-26. When you are ready to drive, move the shift lever out of PARK (P) before you release the parking brake. If torque lock does occur, you may need to have another vehicle push your vehicle a little uphill to take some of the pressure from the parking pawl in the transaxle, so you can pull the shift lever out of PARK (P). Shifting Out of Park (P) Your vehicle has an automatic transaxle shift lock control system. You must fully apply your regular brakes before you can shift from PARK (P) when the ignition is in RUN. See Automatic Transaxle Operation on page 2-22. If you cannot shift out of PARK (P), ease pressure on the shift lever by pushing it all the way into PARK (P) while keeping the brake pedal pushed down. Release the shift lever button if you have a console shift. Then move the shift lever out of PARK (P), being sure to press the shift lever button if you have a console shift. If you ever hold the brake pedal down but still cannot shift out of PARK (P), try this: 1. Turn the ignition key to ACCESSORY. 2. Apply and hold the brake pedal down until the end of Step 4. 3. Shift to NEUTRAL (N). 4. Start the engine and shift to the drive gear you want. 5. Have the vehicle ﬁxed as soon as you can. 2-27 Parking Over Things That Burn Engine Exhaust {CAUTION: Engine exhaust can kill. It contains the gas carbon monoxide (CO), which you cannot see or smell. It can cause unconsciousness and death. You might have exhaust coming in if: (cid:127) Your exhaust system sounds strange or different. (cid:127) Your vehicle gets rusty underneath. (cid:127) Your vehicle was damaged in a collision. (cid:127) Your vehicle was damaged when driving over high points on the road or over road debris. (cid:127) Repairs were not done correctly. (cid:127) Your vehicle or exhaust system had been modiﬁed improperly. If you ever suspect exhaust is coming into your vehicle: (cid:127) Drive it only with all the windows down to blow out any CO; and (cid:127) Have your vehicle ﬁxed immediately. {CAUTION: Things that can burn could touch hot exhaust parts under your vehicle and ignite. Do not park over papers, leaves, dry grass, or other things that can burn. 2-28 Running the Engine While Parked It is better not to park with the engine running. But if you ever have to, here are some things to know. {CAUTION: {CAUTION: Idling the engine with the climate control system off could allow dangerous exhaust into your vehicle. See the earlier caution under Engine Exhaust on page 2-28. Also, idling in a closed-in place can let deadly carbon monoxide (CO) into your vehicle even if the climate control fan is at the highest setting. One place this can happen is a garage. Exhaust — with CO — can come in easily. NEVER park in a garage with the engine running. Another closed-in place can be a blizzard. See Winter Driving on page 4-24. It can be dangerous to get out of your vehicle if the shift lever is not fully in PARK (P) with the parking brake ﬁrmly set. Your vehicle can roll. Do not leave your vehicle when the engine is running unless you have to. If you have left the engine running, the vehicle can move suddenly. You or others could be injured. To be sure your vehicle will not move, even when you are on fairly level ground, always set your parking brake and move the shift lever to PARK (P). Follow the proper steps to be sure your vehicle will not move. See Shifting Into Park (P) on page 2-26. If you are parking on a hill and if you are pulling a trailer, also see Towing a Trailer on page 4-36. 2-29 Mirrors Manual Rearview Mirror Adjust all the mirrors so you can see clearly when you are sitting in a comfortable driving position. To reduce glare from headlamps behind you, pull the lever at the bottom of the mirror toward you (to the night position). To return the mirror back to the day position, push the lever away from you. There are two lamps located on the bottom of the mirror. Press the button next to each lamp to turn it on and off. Manual Rearview Mirror with OnStar® If the vehicle has this mirror, it has a lever located at the bottom of the mirror between the two lamps. The lever is used to change the mirror from the day to the night position. To reduce glare from headlamps behind you while driving at night, pull the lever toward you. To return the mirror to the day position, return the lever to its original position. There are two map lamps located on the bottom of the mirror. Press the button next to each lamp to turn it on and off. There are also OnStar® buttons located at the bottom of the mirror face. See your dealer for more information on the system and how to subscribe to OnStar®. See OnStar® System on page 2-32 for more information about the services OnStar® provides. Automatic Dimming Rearview Mirror Your vehicle may be equipped with an automatic dimming rearview mirror. Push the center button on the bottom of the mirror to turn this feature on. The mirror will darken gradually to reduce glare from headlamps behind you. This may take a few moments. The mirror will lighten whenever you shift to REVERSE (R). There are two lamps located on the bottom of the mirror. Press the button next to each lamp to turn it on and off. One photocell on the front of the mirror senses when it is becoming dark outside. Another photocell, facing rearward, senses headlamps behind you. To turn the automatic dimming feature off, press the center button again. To keep the photocells operating well, occasionally clean them with a cotton swab and glass cleaner. 2-30 Automatic Dimming Rearview Mirror with OnStar® Your vehicle may have an automatic dimming rearview mirror with the OnStar® System. Press the button located below the mirror, on the far left, for up to three seconds to turn the automatic dimming feature off and on. While turned on, this mirror functions exactly like the automatic dimming mirror described previously. There are two lamps located on the bottom of the mirror. Press the button next to each lamp to turn it on and off. There are also OnStar® buttons located at the bottom of the mirror. See your dealer for more information on the system and how to subscribe to OnStar®. See OnStar® System on page 2-32 for more information about the service OnStar® provides. Outside Power Mirrors The controls for the outside power mirrors are located on the driver’s door armrest. Use the selector switch located below the four-way control panel to choose either the left or right outside mirror. Then press any of the four arrows located on the control pad to move each mirror in the desired direction. Adjust each mirror so you can see the side of your vehicle and the area beside and behind your vehicle. 2-31 Outside Convex Mirror Your passenger’s side mirror is convex. A convex mirror’s surface is curved so you can see more from the driver’s seat. OnStar® System {CAUTION: A convex mirror can make things (like other vehicles) look farther away than they really are. If you cut too sharply into the right lane, you could hit a vehicle on your right. Check your inside mirror or glance over your shoulder before changing lanes. Outside Heated Mirrors If your vehicle has this option, the surface of both outside mirrors will heat when you activate the rear window defogger. See “Rear Window Defogger” under Climate Control System on page 3-19. 2-32 OnStar® uses global positioning system (GPS) satellite technology, wireless communications, and live advisors to provide you with a wide range of safety, security, information, and convenience services. If your airbags deploy, the system is designed to make an automatic call to OnStar® Emergency where we can request emergency services be sent to your location. If you lock your keys in the car, call OnStar® at 1-888-4-ONSTAR and they can send a signal to unlock your doors. If you need roadside assistance, press the OnStar® button and they will get you the help you need. A complete OnStar® User’s Guide and the Terms and Conditions of the OnStar® Subscription Service Agreement are included in the vehicle’s glove box literature. For more information, visit www.onstar.com or www.onstar.ca, contact OnStar® at 1-888-4-ONSTAR (1-888-466-7827), or press the OnStar® button to speak to an OnStar® advisor 24 hours a day, 7 days a week. Terms and conditions of the Subscription Service Agreement can be found at www.onstar.com or www.onstar.ca. OnStar® Services For new vehicles equipped with OnStar®, the Safe and Sound Plan is included for one year from the date of purchase. You can extend this plan beyond the ﬁrst year, or upgrade to the Directions and Connections Plan to meet your needs. For more information, press the OnStar® button to speak to an advisor. Safe and Sound Plan (cid:127) Advanced Automatic Collision Notiﬁcation (cid:127) Automatic Notiﬁcation of Airbag Deployment (cid:127) Emergency Services (cid:127) Roadside Assistance (cid:127) Stolen Vehicle Tracking (cid:127) AccidentAssist (cid:127) Remote Door Unlock/Vehicle Alert (cid:127) Remote Diagnostics (cid:127) Online Concierge Directions and Connections® Plan (cid:127) All Safe and Sound Plan Services (cid:127) Driving Directions (cid:127) RideAssist Information and Convenience Services OnStar® Personal Calling As an OnStar® subscriber, the Personal Calling capability allows you to make hands-free calls using a wireless system that is integrated into the vehicle. Calls can be placed nationwide using simple voice commands with no additional contracts and no additional roaming charges. To ﬁnd out more about OnStar® Personal Calling, refer to the OnStar® User’s Guide in the vehicle’s glove box, visit www.onstar.com or www.onstar.ca, or speak to an OnStar® advisor by pressing the OnStar® button or calling 1-888-4-ONSTAR (1-888-466-7827). OnStar® Virtual Advisor Your vehicle may have Virtual Advisor. It is a feature of OnStar® Personal Calling that uses your minutes to access weather, local traffic reports, and stock quotes. By pressing the phone button and giving a few simple voice commands, you can browse through the various topics. Customize your information proﬁle at www.myonstar.com. See the OnStar® User’s Guide for more information. 2-33 (cid:127) OnStar® Steering Wheel Controls Your vehicle may be equipped with a Talk/Mute button that can be used to interact with OnStar®. See Audio Steering Wheel Controls on page 3-83 for more information. When calling into voice-mail systems, or to dial directory numbers, press this button once, wait for the response, say the number(s) to be dialed, wait for the number(s) to be repeated and then say “dial”. See the OnStar® User’s Guide for more information. Universal Home Remote System The Universal Home Remote System, provides a way to replace up to three hand-held transmitters used to activate devices such as gate operators, garage door openers, entry door locks, security systems, and home lighting. If your vehicle has the Universal Home Remote Transmitter, it complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. 2-34 This device complies with RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Changes and modiﬁcations to this system by other than an authorized service facility could void authorization to use this equipment. Universal Home Remote System Operation Do not use the Universal Home Remote with any garage door opener that does not have the stop and reverse feature. This includes any garage door opener model manufactured before April 1, 1982. If you have a newer garage door opener with rolling codes, please be sure to follow Steps 6 through 8 to complete the programming of your Universal Home Remote Transmitter. Read the instructions completely before attempting to program the Universal Home Remote. Because of the steps involved, it may be helpful to have another person available to assist you in the programming steps. Keep the original hand-held transmitter for use in other vehicles as well as for future Universal Home Remote programming. It is also recommended that upon the sale of the vehicle, the programmed Universal Home Remote buttons should be erased for security purposes. See “Erasing Universal Home Remote Buttons” later in this section or, for assistance, see Customer Assistance Offices on page 7-4. Be sure that people and objects are clear of the garage door or gate operator you are programming. When programming a garage door, it is advised to park outside of the garage. It is recommended that a new battery be installed in your hand-held transmitter for quicker and more accurate transmission of the radio-frequency signal. 2-35 Programming Universal Home Remote Follow these steps to program up to three channels: 1. Press and hold down the two outside Universal Home Remote buttons, releasing only when the Universal Home Remote indicator light begins to ﬂash, after 20 seconds. Do not hold down the buttons for longer than 30 seconds and do not repeat this step to program a second and/or third hand-held transmitter to the remaining two Universal Home Remote buttons. 2. Position the end of your hand-held transmitter about 1 to 3 inches (3 to 8 cm) away from the Universal Home Remote buttons while keeping the indicator light in view. 3. Simultaneously press and hold both the desired Universal Home Remote button and the hand-held transmitter button. Do not release the buttons until Step 4 has been completed. Some entry gates and garage door openers may require you to substitute Step 3 with the procedure noted in “Gate Operator and Canadian Programming” later in this section. 4. The indicator light will ﬂash slowly at ﬁrst and then rapidly after Universal Home Remote successfully receives the frequency signal from the hand-held transmitter. Release both buttons. 5. Press and hold the newly-trained Universal Home Remote button and observe the indicator light. If the indicator light stays on constantly, programming is complete and your device should activate when the Universal Home Remote button is pressed and released. To program the remaining two Universal Home Remote buttons, begin with Step 2 under “Programming Universal Home Remote.” Do not repeat Step 1 as this will erase all of the programmed channels. If the indicator light blinks rapidly for two seconds and then turns to a constant light, continue with Steps 6 through 8 following to complete the programming of a rolling-code equipped device, most commonly, a garage door opener. 6. Locate in the garage, the garage door opener receiver (motor-head unit). Locate the “Learn” or “Smart” button. This can usually be found where the hanging antenna wire is attached to the motor-head unit. 2-36 7. Firmly press and release the “Learn” or “Smart” button. The name and color of the button may vary by manufacturer. You will have 30 seconds to start Step 8. 8. Return to the vehicle. Firmly press and hold the programmed Universal Home Remote button for two seconds, then release. Repeat the press/hold/release sequence a second time, and depending on the brand of the garage door opener, or other rolling code device, repeat this sequence a third time to complete the programming. The Universal Home Remote should now activate your rolling-code equipped device. To program the remaining two Universal Home Remote buttons, begin with Step 2 of “Programming Universal Home Remote.” You do not want to repeat Step 1, as this will erase all previous programming from the Universal Home Remote buttons. Gate Operator and Canadian Programming Canadian radio-frequency laws require transmitter signals to time out or quit after several seconds of transmission. This may not be long enough for Universal Home Remote to pick up the signal during programming. Similarly, some U.S. gate operators are manufactured to time out in the same manner. If you live in Canada, or you are having difficulty programming a gate operator or garage door opener by using the “Programming Universal Home Remote” procedures, regardless of where you live, replace Step 3 under “Programming Universal Home Remote” with the following: Continue to press and hold the Universal Home Remote button while you press and release every two seconds (cycle) the hand-held transmitter button until the frequency signal has been successfully accepted by the Universal Home Remote. The Universal Home Remote indicator light will ﬂash slowly at ﬁrst and then rapidly. Proceed with Step 4 under “Programming Universal Home Remote” to complete. 2-37 Reprogramming a Single Universal Home Remote Button To program a device to Universal Home Remote using a Universal Home Remote button previously trained, follow these steps: 1. Press and hold the desired Universal Home Remote button. Do not release the button. 2. The indicator light will begin to ﬂash after 20 seconds. While still holding the Universal Home Remote button, proceed with Step 2 under “Programming Universal Home Remote” shown earlier in this section. For additional information on Universal Home Remote, see Customer Assistance Offices on page 7-4. Using Universal Home Remote Press and hold the appropriate Universal Home Remote button for at least half of a second. The indicator light will come on while the signal is being transmitted. Erasing Universal Home Remote Buttons To erase programming from the three Universal Home Remote buttons do the following: 1. Press and hold down the two outside buttons until the indicator light begins to ﬂash, after 20 seconds. Do not hold the two outside buttons for longer than 30 seconds. 2. Release both buttons. The Universal Home Remote is now in the training (learning) mode and can be programmed at any time beginning with Step 2 under “Programming Universal Home Remote” shown earlier in this section. Individual buttons cannot be erased, but they can be reprogrammed. See “Reprogramming a Single Universal Home Remote Button” following this section. 2-38 Storage Areas Glove Box To open the glove box, lift up on the lever. Cupholder(s) Your vehicle is equipped with cupholders located between the front seats and in the rear seat armrest. Center Console Storage Area The console has cupholders and a storage area. To open the console’s storage area, press the latch located toward the front of the console lid on the driver’s side of the vehicle. Rear Seat Armrest Your vehicle has a rear seat armrest with cupholders. To access, pull the tab on the armrest forward. Convenience Net The vehicle may have a convenience net located on the back wall of the trunk. The net is not for larger, heavier loads. Store those in the trunk as far forward as possible. Unhook the net so that it will lie ﬂat when not in use. 2-39 Sunroof If your vehicle is equipped with a sunroof, the sunroof switches are located on the overhead console. The sunroof can only be operated when the ignition is in ACCESSORY, RUN, or when Retained Accessory Power (RAP) is active. See Retained Accessory Power (RAP) on page 2-19. Q (Vent/Express-Open): To vent the sunroof when it is closed, press this switch once. When using the vent, the sunshade should be fully opened. The sunshade can be opened or closed manually by sliding it rearward or forward. From the vent position, press this switch again to activate the express-open feature. Press the close switch to stop movement of the sunroof. The sunshade will automatically open when using express-open. A deﬂector will automatically pop up when the sunroof is opened. The deﬂector will retract when the sunroof is closed. R (Close): To close the sunroof, press and hold this switch until the sunroof motor stops, or release the switch when the desired position has been reached. 2-40 Section 3 Instrument Panel Instrument Panel Overview ...............................3-4 Hazard Warning Flashers ................................3-6 Other Warning Devices ...................................3-6 Horn .............................................................3-6 Tilt Wheel .....................................................3-6 Turn Signal/Multifunction Lever .........................3-7 Turn and Lane-Change Signals ........................3-7 Headlamp High/Low-Beam Changer ..................3-8 Flash-to-Pass .................................................3-8 Windshield Wipers ..........................................3-8 Windshield Washer .........................................3-9 Cruise Control ..............................................3-10 Exterior Lamps .............................................3-13 Delayed Headlamps ......................................3-14 Daytime Running Lamps (DRL)/Automatic Headlamp System .....................................3-14 Fog Lamps ..................................................3-15 Instrument Panel Brightness ...........................3-15 Courtesy Lamps ...........................................3-15 Dome Lamp .................................................3-15 Entry Lighting ...............................................3-16 Delayed Entry Lighting ...................................3-16 Delayed Exit Lighting .....................................3-16 Parade Dimming ...........................................3-17 Reading Lamps ............................................3-17 Battery Run-Down Protection ..........................3-17 Accessory Power Outlet(s) .............................3-17 Ashtray(s) and Cigarette Lighter ......................3-18 Climate Controls ............................................3-19 Climate Control System .................................3-19 Outlet Adjustment .........................................3-22 Passenger Compartment Air Filter ...................3-23 Warning Lights, Gages, and Indicators ............3-24 Instrument Panel Cluster ................................3-25 Speedometer and Odometer ...........................3-26 Tachometer .................................................3-26 Safety Belt Reminder Light .............................3-26 Passenger Safety Belt Reminder Light .............3-27 Airbag Readiness Light ..................................3-27 Passenger Airbag Status Indicator ...................3-28 Charging System Light ..................................3-30 Brake System Warning Light ..........................3-31 Anti-Lock Brake System Warning Light .............3-32 Traction Control System (TCS) Warning Light ...3-32 Engine Coolant Temperature Warning Light ......3-33 3-1 Section 3 Instrument Panel Engine Coolant Temperature Gage ..................3-33 Tire Pressure Light .......................................3-34 Malfunction Indicator Lamp .............................3-34 Oil Pressure Light .........................................3-37 Security Light ...............................................3-37 Fog Lamp Light ............................................3-38 Cruise Control Light ......................................3-38 Highbeam On Light .......................................3-38 Fuel Gage ...................................................3-38 Driver Information Center (DIC) .......................3-39 DIC Operation and Displays ...........................3-40 DIC Warnings and Messages .........................3-46 DIC Vehicle Customization .............................3-53 Audio System(s) .............................................3-59 Setting the Time (Without Date Display) ...........3-60 Setting the Time (With Date Display) ...............3-61 Radio with CD (Base) ...................................3-62 Radio with CD (MP3) ....................................3-67 Theft-Deterrent Feature ..................................3-82 Audio Steering Wheel Controls .......................3-83 Radio Reception ...........................................3-83 Care of Your CDs .........................................3-84 Care of the CD Player ...................................3-84 Backglass Antenna .......................................3-85 XM™ Satellite Radio Antenna System .............3-85 3-2 ✍ NOTES 3-3 Instrument Panel Overview 3-4 The main components of your instrument panel are listed here: A. Air Vent. See Outlet Adjustment on page 3-22. B. Remote Trunk Release Button. See “Remote Trunk Release” under Trunk on page 2-11. C. Multifunction Lever. See Turn Signal/Multifunction Lever on page 3-7. D. Instrument Panel Cluster. See Instrument Panel Cluster on page 3-25. E. Hazard Warning Flasher Button. See Hazard Warning Flashers on page 3-6. F. Driver Information Center (DIC) Buttons. See Driver Information Center (DIC) on page 3-39. G. Audio System. See Audio System(s) on page 3-59. H. Exterior Lamps Control. See Exterior Lamps on page 3-13. I. Instrument Panel Brightness. See Instrument Panel Brightness on page 3-15. J. Traction Control On/Off Button (If Equipped). See Traction Control System (TCS) on page 4-9. K. Tilt Steering Wheel Lever. See Tilt Wheel on page 3-6. L. Steering Wheel Cruise Control (If Equipped). See Cruise Control on page 3-10. M. Hood Release. See Hood Release on page 5-11. N. Horn. See Horn on page 3-6. O. Audio Steering Wheel Controls (If Equipped). See Audio Steering Wheel Controls on page 3-83. P. Ignition Switch. See Ignition Positions on page 2-18. Q. Climate Controls. See Climate Control System on page 3-19. R. Accessory Power Outlet. See Accessory Power Outlet(s) on page 3-17. S. Automatic Transaxle Shift Lever. See Automatic Transaxle Operation on page 2-22. T. Glove Box. See Glove Box on page 2-39. 3-5 Horn Press near or on the horn symbols on your steering wheel pad to sound the horn. Tilt Wheel A tilt wheel allows you to adjust the steering wheel before you drive. You can raise the steering wheel to the highest level to give your legs more room when you enter and exit the vehicle. The lever that allows you to tilt the steering wheel is located on the left side of the steering column. To tilt the wheel, hold the wheel and pull the lever. Then move the wheel to a comfortable position and release the lever to lock the wheel in place. Hazard Warning Flashers The hazard warning ﬂashers let you warn others. They also let police know you have a problem. Your front and rear turn signal lamps will ﬂash on and off. The hazard warning ﬂasher button is located on top of the steering column. The hazard warning ﬂashers work no matter what position the key is in, and even if the key is not in. Press the button to make the front and rear turn signal lamps ﬂash. Press the button again to turn the ﬂashers off. When the hazard warning ﬂashers are on, the turn signals will not work. Other Warning Devices If you carry reﬂective triangles, you can set them up at the side of the road about 300 feet (100 m) behind your vehicle. 3-6 Turn Signal/Multifunction Lever The lever on the left side of the steering column includes the following: (cid:127) G Turn and Lane Change Signals. See Turn and Lane-Change Signals on page 3-7. (cid:127) 2 Headlamp High/Low-Beam Changer. See Headlamp High/Low-Beam Changer on page 3-8. Flash-to-Pass. See Flash-to-Pass on page 3-8. (cid:127) N Windshield Wipers. See Windshield Wipers on page 3-8. (cid:127) LQ Windshield Washer. See Windshield Washer on page 3-9. For information on the headlamps, see Exterior Lamps on page 3-13. Turn and Lane-Change Signals The turn signal has two upward (for right) and two downward (for left) positions. These positions allow you to signal a turn or a lane change. To signal a turn, move the lever all the way up or down. When the turn is ﬁnished, the lever will return automatically. An arrow on the instrument panel cluster will ﬂash in the direction of the turn or lane change. To signal a lane change, raise or lower the lever until the arrow starts to ﬂash. Hold it there until you complete your lane change. The lever will return by itself when you release it. If the arrow ﬂashes faster than normal as you signal a turn or a lane change, a signal bulb may be burned out and other drivers won’t see your turn signal. If a bulb is burned out, replace it to help avoid an accident. If the arrows don’t go on at all when you signal a turn, check for burned-out bulbs and then check the fuse. See Fuses and Circuit Breakers on page 5-95. 3-7 (cid:127) Turn Signal On Chime If you leave either one of your turn signals on and drive more than three-quarters of a mile (1.2 km), a chime will sound to alert you. Headlamp High/Low-Beam Changer To change your headlamps from low beams to high beams, or from high to low, pull the multifunction lever all the way toward you. Then release it. While the high beams are on, this light will appear on the instrument panel cluster. This light works only while the key is in RUN. The fog lamps (if equipped) are not illuminated when the high beams are on. Flash-to-Pass With the turn signal lever in the low-beam position, pull the lever toward you momentarily to switch to high-beam, (to signal you are going to pass). If the headlamps are on, they will return to low-beam when the lever is released. This feature operates even if the headlamps are off. Windshield Wipers Be sure to clear ice and snow from the wiper blades before using them. If they are frozen to the windshield, gently loosen or thaw them. Damaged wiper blades may not clear the windshield well, making it harder to see and drive safely. If the blades do become damaged, install new blades or blade inserts. For more information, see Windshield Wiper Blade Replacement on page 5-52 Heavy snow or ice can overload the wiper motor. A circuit breaker will stop the motor until it cools down. Clear away snow or ice to prevent an overload. You control the windshield wipers by turning the band with the wiper symbol on it. 3-8 8(Mist): For a single wiping cycle, turn the band to mist. Hold it there until the wipers start. Then let go. The wipers will stop after one wipe. If you want more wipes, hold the band on mist longer. N(Delay): You can set the wiper speed for a long or short delay between wipes. This can be very useful in light rain or snow. Turn the band to choose the delay time. The closer to the top of the lever, the shorter the delay. 6 (Low Speed): For steady wiping at low speed, turn the band away from you to the ﬁrst solid band past the delay settings. For high-speed wiping, turn the band further, to the second solid band past the delay settings. To stop the wipers, move the band to off. 1 (High Speed): For high-speed wiping, turn the band further, to the second solid band past the delay settings. 9(Off): To stop the wipers, move the band to off. Windshield Washer At the top of the multifunction lever, there’s a paddle with the windshield washer symbol on it. To spray washer ﬂuid on the windshield, push the paddle. The wipers will run for several sweeps and then either stop or return to your preset speed. The ignition key must be in ACCESSORY or RUN for this to work. See Windshield Washer Fluid on page 5-39. {CAUTION: In freezing weather, do not use your washer until the windshield is warmed. Otherwise the washer ﬂuid can form ice on the windshield, blocking your vision. When you are low on washer ﬂuid, a message will be illuminated in the Driver Information Center (DIC) for 60 seconds. When the ignition is turned off, a message will appear again for three seconds as a reminder that the ﬂuid level is low. For more information on DIC messages, see DIC Warnings and Messages on page 3-46. The washer ﬂuid message will no longer display when the washer ﬂuid reservoir has been ﬁlled. 3-9 Cruise Control With cruise control, you can maintain a speed of about 25 mph (40 km/h) or more without keeping your foot on the accelerator. This can really help on long trips. Cruise control does not work at speeds below about 25 mph (40 km/h). When you apply your brakes, cruise control is turned off. {CAUTION: Cruise control can be dangerous where you cannot drive safely at a steady speed. So, do not use your cruise control on winding roads or in heavy traffic. Cruise control can be dangerous on slippery roads. On such roads, fast changes in tire traction can cause excessive wheel slip, and you could lose control. Do not use cruise control on slippery roads. If your vehicle is in cruise control when the traction control system (if equipped) begins to limit wheel spin, the cruise control will automatically disengage. 3-10 See Traction Control System (TCS) on page 4-9. When road conditions allow you to safely use it again, you may turn the cruise control back on. The cruise control buttons are located on left side of the steering wheel. T (On/Off): Press this button to turn cruise control on and off. The indicator will be lit when cruise control is on. + RES (Resume/Accelerate): Press this button to make the vehicle accelerate or resume to a previously set speed. SET–: Press this button to set the speed or make the vehicle decelerate. [ (Cancel): Press this button to cancel cruise control. Setting Cruise Control Cruise control will not work if your parking brake is set, or if the master cylinder brake ﬂuid level is low. The cruise control light on the instrument panel cluster will come on after the cruise control has been set to the desired speed. {CAUTION: If you leave your cruise control on when you are not using cruise, you might hit a button and go into cruise when you do not want to. You could be startled and even lose control. Keep the cruise control switch off until you want to use cruise control. 1. Press the cruise control On/Off button. 2. Get up to the speed you want. 3. Press and release the SET– button located on the steering wheel. 4. Take your foot off the accelerator. Resuming a Set Speed Suppose you set your cruise control at a desired speed and then you apply the brake. This shuts off the cruise control. But you do not need to reset it. Once you are driving about 25 mph (40 km/h) or more, press the +RES button on your steering wheel. The vehicle will go back to your chosen speed and stay there. Increasing Speed While Using Cruise Control To increase the cruise speed while using cruise control: (cid:127) Press and hold the +RES button on the steering wheel until you reach your new desired speed, then release it. To increase vehicle speed in small increments, press the +RES button. 3-11 (cid:127) Reducing Speed While Using Cruise Control To reduce your speed while using cruise control: (cid:127) Press and hold the SET– button on the steering wheel until you reach the lower speed you want, then release it. To slow down in very small amounts, press the SET– button on the steering wheel brieﬂy. Each time you do this, you will go about 1 mph (1.6 km/h) slower. Passing Another Vehicle While Using Cruise Control Use the accelerator pedal to increase vehicle speed. When you take your foot off the pedal, your vehicle will slow down to the cruise speed you set earlier. Using Cruise Control on Hills How well your cruise control will work on hills depends upon your speed, load and the steepness of the hills. When going up steep hills, you may have to step on the accelerator pedal to maintain your speed. When going downhill, you may have to brake or shift to a lower gear to keep your speed down. Of course, applying the brake takes you out of cruise control. Many drivers ﬁnd this to be too much trouble and do not use cruise control on steep hills. Ending Cruise Control There are three ways to end cruise control: (cid:127) Step lightly on the brake pedal. (cid:127) Press the [ (cancel) button on the steering wheel. (cid:127) Press the T (on/off) button on the steering wheel. Erasing Speed Memory When you turn off the cruise control or the ignition, your cruise control set speed memory is erased. 3-12 (cid:127) Exterior Lamps The exterior lamps control is located on the instrument panel to the left of the steering wheel. License Plate Lamps Instrument Panel Lights ;(Parking Lamps): Turn the control to this position to turn on the parking lamps together with the following: It controls the following systems: (cid:127) Headlamps Taillamps (cid:127) Parking Lamps License Plate Lamps Instrument Panel Lights Fog Lamps (if equipped) The exterior lamps control has four positions: O (Off): Momentarily turn the control to this position to turn off the automatic light control. Momentarily turn to this position again to turn automatic light control on again. AUTO (Automatic): Turn the control to this position to automatically turn on the headlamps at normal brightness, together with the following: (cid:127) Parking Lamps Taillamps Taillamps License Plate Lamps Instrument Panel Lights 2(Headlamps): Turn the control to this position to turn on the headlamps together with the following lamps listed below. A warning chime will sound if you open the driver’s door when the ignition switch is off and the headlamps are on. (cid:127) Parking Lamps Taillamps License Plate Lamps Instrument Panel Lights - (Fog Lamps, If Equipped): Push the fog lamps control in to turn on the fog lamps. See Fog Lamps on page 3-15. 3-13 (cid:127) (cid:127) (cid:127) (cid:127) (cid:127) (cid:127) (cid:127) (cid:127) (cid:127) (cid:127) (cid:127) (cid:127) (cid:127) Delayed Headlamps The delayed headlamps feature provides a period of exterior lighting as you leave the area around your vehicle. The feature is activated when the headlamps are on due to the automatic headlamps control feature later described in this section, and when the ignition is turned off. Your headlamps will then remain on until the exterior lamps control is moved to the parking lamps position or until either a 30 second or 60 second lighting period has ended. If you turn off the ignition with the headlamps switch in the parking lamps or headlamps position, the delayed headlamps cycle will not occur. To disable the delayed headlamps feature or change the time of delay, see “Exit Lighting” under DIC Vehicle Customization on page 3-53. Daytime Running Lamps (DRL)/ Automatic Headlamp System Daytime Running Lamps (DRL) can make it easier for others to see the front of your vehicle during the day. DRL can be helpful in many different driving conditions, but they can be especially helpful in the short periods after dawn and before sunset. Fully functional daytime running lamps are required on all vehicles ﬁrst sold in Canada. 3-14 A light sensor on top of the instrument panel makes the DRL work, so be sure it is not covered. The DRL system’s automatic headlamp control will make the low-beam headlamps come on at a reduced brightness when the following conditions are met: The ignition is in RUN. The exterior lamps control is in AUTO. The engine is running. When the DRL are on, only the low-beam headlamps, at a reduced level of brightness, will be on. The headlamps, taillamps, sidemarker, and other lamps will not be on. The instrument panel and cluster will also not be lit. When it is dark enough outside, your low-beam headlamps will turn off and the headlamps and parking lamps will turn on. The other lamps that come on with the headlamps will also come on. When it is bright enough outside, the headlamps will go off and the DRL will come on. As with any vehicle, you should turn on the regular headlamp system when you need it. (cid:127) (cid:127) (cid:127) Fog Lamps - (Fog Lamps): If your vehicle is equipped with fog lamps, it is located on the exterior lamps control. The exterior lamps control is located on the instrument panel to the left of the steering column. Your ignition must be in RUN for the fog lamps to illuminate. To turn the fog lamps on, press exterior lamps button. A light will come on in the button to let you know that the fog lamps are on. Press the exterior lamps button again to turn the fog lamps off. The ignition must be in RUN and the parking lamps must be on for your fog lamps to work. The parking lamps will turn on automatically when you turn on the fog lamps. The fog lamps will go off while you change to high-beam headlamps. Some localities have laws that require the headlamps to be on along with the fog lamps. Instrument Panel Brightness D (Instrument Panel Brightness): The knob with this symbol on it is located next to the exterior lamps control. Push and pull the knob out halfway and then turn the knob clockwise to brighten or counterclockwise to dim the lights. Courtesy Lamps When a door is opened, the courtesy lamps automatically come on. They make it easy for you to enter and leave your vehicle. You can also manually turn these lamps on by turning the instrument panel brightness control clockwise all the way. The reading lamps, located on the rearview mirror, can be turned on or off independent of the automatic courtesy lamps, when the doors are closed. Dome Lamp The dome lamp will come on when you open a door. You can also turn this lamp on by turning the instrument panel brightness control clockwise. 3-15 Entry Lighting Your vehicle may have the entry lighting feature. Your courtesy lamps will come on and stay on for a set time whenever you press UNLOCK on the remote keyless entry transmitter, if equipped. If you open a door, the lamps will stay on while it’s open and then turn off automatically about 25 seconds after you close it. If you press UNLOCK and don’t open a door, the lamps will turn off after about 40 seconds. Illuminated entry includes a feature called theater dimming. With theater dimming, the lamps don’t just turn off at the end of the delay time. Instead, they slowly dim after the delay time until they go out. The delay time is canceled if you turn the ignition key to RUN or press the power door lock switch. When the ignition is on, illuminated entry is inactive, which means the courtesy lamps won’t come on unless a door is opened. Delayed Entry Lighting Delayed entry lighting illuminates the interior for a period of time after all the doors have been closed. The ignition must be off for delayed entry lighting to work. Immediately after both doors have been closed, the delayed entry lighting feature will continue to work until one of the following occurs: The ignition is in RUN. The doors are locked. (cid:127) An illumination period of 20 seconds has elapsed. If during the illumination period a door is opened, the timed illumination period will be canceled and the interior lamps will remain on. Delayed Exit Lighting This feature illuminates the interior for a period of time after the key is removed from the ignition. The ignition must be off for delayed exit lighting to work. When the key is removed, interior illumination will activate and remain on until one of the following occurs: The ignition is in RUN. The power door locks are activated. (cid:127) An illumination period of 20 seconds has elapsed. If during the illumination period a door is opened, the timed illumination period will be canceled and the interior lamps will remain on because a door is open. 3-16 (cid:127) (cid:127) (cid:127) (cid:127) Parade Dimming The instrument panel has an added feature called parade dimming. This feature prohibits the dimming of your instrument panel displays during the daylight while the headlamps are on so that you’ll still be able to see the displays. Reading Lamps The reading lamps are located on the rearview mirror. Press the button to turn them on and off. Battery Run-Down Protection Your vehicle has a feature to help prevent you from draining the battery in case you accidentally leave on the interior courtesy lamps, reading/map lamps, visor vanity lamps, trunk lamp or glove box lamps. If you leave any of these lamps on, they will automatically turn off after 10 minutes, if the ignition is off. The lamps won’t come back on again until you do the following: Turn the ignition on. Turn the exterior lamps control off, then on again. If your vehicle has less than 15 miles (25 km) on the odometer, the battery saver will turn off the lamps after only three minutes. Battery rundown protection will also work if the headlamps are left on. After having been left on for 10 minutes, the headlamps and the parking lamps will ﬂash three times. They will remain on for one more minute before turning off automatically. Accessory Power Outlet(s) Your vehicle has a two 12-volt outlets which can be used to plug in electrical equipment such as a cellular telephone, a compact disc player, etc. One is located at the front of the console and the other is located at the rear of the console. Lift the cover to access the outlet. When not using the outlet, make sure the protective cover is in place. Notice: Leaving electrical equipment on for extended periods will drain the battery. Always turn off electrical equipment when not in use and do not plug in equipment that exceeds the maximum amperage rating. Certain accessory power plugs may not be compatible with the accessory power outlet and could result in blown vehicle or adapter fuses. If you experience a problem see your dealer for additional information on the accessory power plugs. 3-17 (cid:127) (cid:127) Notice: Adding any electrical equipment to your vehicle may damage it or keep other components from working as they should. The repairs would not be covered by your warranty. Do not use equipment exceeding maximum amperage rating. Check with your dealer before adding electrical equipment. When adding electrical equipment, be sure to follow the proper installation instructions included with the equipment. Check with your dealer before adding electrical equipment, and never use anything that exceeds the amperage rating. Notice: damage not covered by your warranty. Do not hang any type of accessory or accessory bracket from the plug because the power outlets are designed for accessory power plugs only. Improper use of the power outlet can cause If you put papers, pins, or other ﬂammable Ashtray(s) and Cigarette Lighter Notice: items in the ashtray, hot cigarettes or other smoking materials could ignite them and possibly damage your vehicle. Never put ﬂammable items in the ashtray. Your vehicle may have a cigarette lighter and ashtray located on the console. The ashtray is removable and has a cupholder and liner underneath. To remove the ashtray, lift it up with the liner and pull it out. Notice: Holding a cigarette lighter in while it is heating will not allow the lighter to back away from the heating element when it is hot. Damage from overheating may occur to the lighter or heating element, or a fuse could be blown. Do not hold a cigarette lighter in while it is heating. To activate the cigarette lighter, push it into the heating element and let go. When the lighter is ready it will pop out by itself. 3-18 Climate Controls Climate Control System Your vehicle may be equipped with a dual or single climate control system. With this system you can control the heating, cooling, defrost, defog, and ventilation for your vehicle. Dual Zone with Optional Heated Seat Controls Single Zone Manual Operation Turn the right knob clockwise or counterclockwise to direct the airﬂow inside of your vehicle. To change the current mode, select one of the following: H (Vent): This mode directs air to the instrument panel outlets. ) (Bi-Level): This mode directs approximately half of the of air to the instrument panel outlets and the other half to the ﬂoor outlets. 3-19 6 (Floor): This mode directs most of the air to the ﬂoor outlets, with some of the air directed to the windshield and side window outlets. In this mode, the system will automatically select Outside Air. The right knob can also be used to select defog or defrost mode. For more information, see “Defogging and Defrosting” later in this section. By positioning the right knob between two modes, a combination of those two modes is selected. The air conditioning compressor will be engaged unless the outside temperature is 40°F (4°C) or below. Recirculation cannot be selected when in Floor mode. 9 (Fan): Turn the left knob clockwise or counterclockwise to increase or decrease the fan speed. If the airﬂow seems low when the fan is at the highest setting, the passenger compartment air ﬁlter, if equipped, may need to be replaced. For more information, see Passenger Compartment Air Filter on page 3-23 and Scheduled Maintenance on page 6-4. : (Outside Air): When this mode is on, outside air will circulate throughout your vehicle. When the button is pressed, an indicator light in the button will come on to let you know that it is activated. Outside air cannot be used with the recirculation mode. ? (Recirculation): When the button is pressed, an indicator light will come on. This mode keeps outside air from entering the vehicle. It can be used to prevent outside air and odors from entering your vehicle. Recirculation may also help heat or cool the air inside your vehicle more quickly once the temperature inside the vehicle is equal to or better than the outside temperature. The recirculation mode cannot be used with outside air, ﬂoor, defrost, or defog modes. Temperature Control: Rotate the thumbwheels up or down to increase or decrease the temperature on the driver’s side or the passenger side of the vehicle for the dual zone system. Turn the center knob clockwise or counterclockwise to increase or decrease the temperature for the single zone system. # (Air Conditioning): Press this button to turn the air conditioning system on or off. When A/C is pressed, an indicator light will come on to let you know that the air conditioning has been activated. On hot days, open the windows to let hot inside air escape; then close them. This helps to reduce the time it takes for your vehicle to cool down. It also helps the system to operate more efficiently. 3-20 For quick cool down on hot days, do the following: 1. Select the vent mode. 2. Select the outside air. 3. Select A/C. 4. Select the coolest temperature for both zones. 5. Select the highest fan speeds. 6. Once the vehicle’s interior temperature is below the outside temperature, select recirculation mode for enhanced cooling. Using these settings together for long periods of time may cause the air inside of your vehicle to become too dry. To prevent this from happening, after the air inside of your vehicle has cooled, turn the recirculation mode off. The air conditioning system removes moisture from the air, so you may sometimes notice a small amount of water dripping underneath your vehicle while idling or after turning off the engine. This is normal. Defogging and Defrosting Fog on the inside of the windows is a result of high humidity (moisture) condensing on the cool window glass. This can be minimized if the climate control system is used properly. There are two modes to clear fog or frost from your windshield. Use the defog mode to clear the windows of fog or moisture and warm the passengers. Use the defrost mode to remove fog or frost from the windshield more quickly. Turn the right knob clockwise to select the defog or defrost mode. Do not drive the vehicle until all the windows are clear. - (Defog): This mode directs air equally to the windshield and the ﬂoor outlets. When you select this mode, the system turns off recirculation and runs the air conditioning compressor unless the outside temperature is below 40°F (4°C). The recirculation mode cannot be selected while in the defog mode. 0 (Defrost): This mode directs most of the air to the windshield, side window vents, and to the ﬂoor vents. In this mode, the system will automatically force outside air into your vehicle. The recirculation mode cannot be selected while in the defog mode. The air conditioning compressor will run automatically in this setting, unless the outside temperature is below 40°F (4°C). 3-21 Rear Window Defogger The rear window defogger uses a warming grid to remove fog from the rear window. <: The rear window defogger will turn off automatically after it has been activated. The duration the rear window defogger is on will be longer if the vehicle is being driven. The defogger can also be turned off by pressing the button again or by turning off the engine. The heated outside rearview mirrors will heat to help clear fog or frost from the surface of the mirror when the rear window defogger buttin is on. Notice: Do not use anything sharp on the inside of the rear window. If you do, you could cut or damage the warming grid, and the repairs would not be covered by your warranty. Do not attach a temporary vehicle license, tape, a decal or anything similar to the defogger grid. Outlet Adjustment Use the knob located below or to the side of the outlet, to change the direction of the air ﬂow. Operation Tips (cid:127) Clear away any ice, snow or leaves from the air inlets at the base of the windshield that may block the ﬂow of air into your vehicle. (cid:127) Use of non-GM approved hood deﬂectors may adversely affect the performance of the system. (cid:127) Keep the path under the front seats clear of objects to help circulate the air inside your vehicle more effectively. If the airﬂow seems low when the fan is at the highest setting, the passenger compartment air ﬁlter, if equipped, may need to replaced. For more information, see Passenger Compartment Air Filter on page 3-23 and Scheduled Maintenance on page 6-4. 3-22 (cid:127) Passenger Compartment Air Filter Your vehicle has a passenger compartment particulate air ﬁlter. It is located underneath the hood just below the windshield wiper arm on the passenger’s side of the vehicle, underneath the air inlet grille. The ﬁlter traps most of the pollen from air entering the climate control system. Like the engine’s air cleaner/ﬁlter, it may need to be changed periodically to ensure system performance. For information on how often to change the passenger compartment air ﬁlter, see Scheduled Maintenance on page 6-4. To change the passenger compartment air ﬁlter, use the following steps: 1. Turn off the ignition when the windshield wipers are in the up position. 2. Raise the vehicle hood. 3. Disconnect the windshield washer pump hose from the fender rail and air inlet grille. 4. Peel back the hood weatherstrip from the passenger’s side of the vehicle halfway to center. 5. Remove the air inlet grille retainers. 6. Remove the air inlet grille. 7. Remove the water deﬂector plate. 8. Remove the old passenger compartment air ﬁlter. 9. Reverse the steps to install the new air ﬁlter. For the type of ﬁlter to use, see Normal Maintenance Replacement Parts on page 6-13. 3-23 Warning Lights, Gages, and Indicators This part describes the warning lights and gages that may be on your vehicle. The pictures will help you locate them. Warning lights and gages can signal that something is wrong before it becomes serious enough to cause an expensive repair or replacement. Paying attention to your warning lights and gages could also save you or others from injury. Warning lights come on when there may be or is a problem with one of your vehicle’s functions. As you will see in the details on the next few pages, some warning lights come on brieﬂy when you start the engine just to let you know they’re working. If you are familiar with this section, you should not be alarmed when this happens. Gages can indicate when there may be or is a problem with one of your vehicle’s functions. Often gages and warning lights work together to let you know when there’s a problem with your vehicle. When one of the warning lights comes on and stays on when you are driving, or when one of the gages shows there may be a problem, check the section that tells you what to do about it. Please follow this manual’s advice. Waiting to do repairs can be costly – and even dangerous. So please get to know your warning lights and gages. They’re a big help. Your vehicle may also have a Driver Information Center (DIC) that works along with the warning lights and gages. See Driver Information Center (DIC) on page 3-39. 3-24 Instrument Panel Cluster Your instrument panel cluster is designed to let you know at a glance how your vehicle is running. You will know how fast you are going, about how much fuel is in your tank and many other things you need to drive safely and economically. United States Uplevel shown, Base and Canada similar 3-25 Safety Belt Reminder Light When the key is turned to RUN, a chime will come on for several seconds to remind people to fasten their safety belts, unless the driver’s safety belt is already buckled. This chime and light will be repeated if the passenger remains unbuckled and the vehicle is in motion. The safety belt light will also come on and stay on for several seconds, then it will ﬂash for several more. Speedometer and Odometer Your speedometer lets you see your speed in both miles per hour (mph) and kilometers per hour (km/h). Your odometer shows how far your vehicle has been driven in either miles (used in the United States) or in kilometers (used in Canada). Your vehicle has a tamper-resistant odometer. If you see ERROR, you’ll know someone has probably tampered with it and the numbers may not be accurate. You may wonder what happens if your vehicle needs a new odometer installed. If the new one can be set to the mileage total of the old odometer, then that will be done. But if it can’t, then it will be set at zero and a label must be put on the driver’s door to show the old mileage reading when the new odometer was installed. If you operate the engine with the Tachometer Notice: tachometer in the shaded warning area, your vehicle could be damaged, and the damages would not be covered by your warranty. Do not operate the engine with the tachometer in the shaded warning area. The tachometer displays the engine speed in revolutions per minute (rpm). 3-26 Passenger Safety Belt Reminder Light Several seconds after the key is turned to RUN or START, a chime will sound for several seconds to remind the front passenger to buckle their safety belt. This would only occur if the passenger airbag is enabled. See Passenger Sensing System on page 1-60 for more information. The passenger safety belt light will also come on and stay on for several seconds, then it will ﬂash for several more. This chime and light will be repeated if the passenger remains unbuckled and the vehicle is in motion. Airbag Readiness Light There is an airbag readiness light on the instrument panel, which shows the airbag symbol. The system checks the airbag’s electrical system for malfunctions. The light tells you if there is an electrical problem. The system check includes the airbag sensors, the airbag modules, the wiring and the crash sensing and diagnostic module. For more information on the airbag system, see Airbag System on page 1-52. This light will come on when you start your vehicle, and it will ﬂash for a few seconds. Then the light should go out. This means the system is ready. If the passenger’s safety belt is buckled, neither the chime nor the light will come on. 3-27 If the airbag readiness light stays on after you start the vehicle or comes on when you are driving, your airbag system may not work properly. Have your vehicle serviced right away. Passenger Airbag Status Indicator Your vehicle has the passenger sensing system. Your overhead console has a passenger airbag status indicator. {CAUTION: If the airbag readiness light stays on after you start your vehicle, it means the airbag system may not be working properly. The airbags in your vehicle may not inﬂate in a crash, or they could even inﬂate without a crash. To help avoid injury to yourself or others, have your vehicle serviced right away if the airbag readiness light stays on after you start your vehicle. The airbag readiness light should ﬂash for a few seconds when you turn the ignition key to RUN. If the light does not come on then, have it ﬁxed so it will be ready to warn you if there is a problem. 3-28 United States Canada When the ignition key is turned to RUN or START, the passenger airbag status indicator will light ON and OFF, or the symbol for on and off, for several seconds as a system check. If you use remote start to start your vehicle from a distance (if equipped), you may not see the system check. Then, after several more seconds, the status indicator will light either ON or OFF, or either the on or off symbol to let you know the status of the right front passenger’s frontal airbag and side impact airbag (if equipped). Your vehicle has a rear seat that will accommodate a rear-facing child restraint. A label on your sun visor says, “Never put a rear-facing child seat in the front.” This is because the risk to the rear-facing child is so great, if the airbags deploy. {CAUTION: Even though the passenger sensing system is designed to turn off the right front passenger’s frontal airbag and side impact airbag (if equipped) if the system detects a rear-facing child restraint, no system is fail-safe, and no one can guarantee that an airbag will not deploy under some unusual circumstance, even though it is turned off. We recommend that rear-facing child restraints be transported in vehicles with a rear seat that will accommodate a rear-facing child restraint, whenever possible. If the word ON or the on symbol is lit on the passenger airbag status indicator, it means that the right front passenger’s airbag or airbags are enabled (may inﬂate). {CAUTION: If the on indicator comes on when you have a rear-facing child restraint installed in the right front passenger’s seat, it means that the passenger sensing system has not turned off the passenger’s frontal airbag and seat-mounted side impact airbag (if equipped). A child in a rear-facing child restraint can be seriously injured or killed if the right front passenger’s airbag inﬂates. This is because the back of the rear-facing child restraint would be very close to the inﬂating airbag. Do not use a rear-facing child restraint in the right front passenger’s seat if the airbag is turned on. If the word OFF or the off symbol is lit on the passenger airbag status indicator, it means that the passenger sensing system has turned off the right front passenger’s airbag or airbags. See Passenger Sensing System on page 1-60 for more on this, including important safety information. 3-29 If, after several seconds, all status indicator lights remain on, or if there are no lights at all, there may be a problem with the lights or the passenger sensing system. See your dealer for service. {CAUTION: If the off indicator and the airbag readiness light ever come on together, it means that something may be wrong with the airbag system. If this ever happens, have the vehicle serviced promptly, because an adult-size person sitting in the right front passenger seat may not have the protection of an airbag. See Airbag Readiness Light on page 3-27. Charging System Light The charging system light will come on brieﬂy when you turn on the ignition, but the engine is not running, as a check to show you it is working. It should go out once the engine is running. If it stays on, or comes on while you are driving, you may have a problem with the charging system. It could indicate that you have problems with a generator drive belt, or another electrical problem. Have it checked right away. Driving while this light is on could drain your battery. If you must drive a short distance with the light on, be certain to turn off all your accessories, such as the radio and air conditioner. 3-30 Brake System Warning Light Your vehicle’s hydraulic brake system is divided into two parts. If one part is not working, the other part can still work and stop you. For good braking, though, you need both parts working well. If the warning light comes on, there is a brake problem. Have your brake system inspected right away. United States Canada This light should come on brieﬂy when you turn the ignition key to RUN. If it does not come on then, have it ﬁxed so it will be ready to warn you if there is a problem. When the ignition is on, the brake system warning light will also come on when you set your parking brake. The light will stay on if your parking brake does not release fully. If it stays on after your parking brake is fully released, it means you have a brake problem. If the light comes on while you are driving, pull off the road and stop carefully. You may notice that the pedal is harder to push or, the pedal may go closer to the ﬂoor. It may take longer to stop. If the light is still on, have the vehicle towed for service. See Brake System Warning Light on page 3-31 and Towing Your Vehicle on page 4-34. {CAUTION: Your brake system may not be working properly if the brake system warning light is on. Driving with the brake system warning light on can lead to an accident. If the light is still on after you have pulled off the road and stopped carefully, have the vehicle towed for service. 3-31 Anti-Lock Brake System Warning Light Traction Control System (TCS) Warning Light If your vehicle is equipped with anti-lock brakes, the anti-lock brake system warning light should come on for a few seconds when you turn the ignition key to RUN. For vehicles equipped with the traction control system, this warning light should come on brieﬂy when the engine is started. If the anti-lock brake system warning light stays on longer than normal after you’ve started your engine, turn the ignition off or, if the light comes on and stays on when you are driving, stop as soon as possible and turn the ignition off. Then start the engine again to reset the system. If the light still stays on, or comes on again while you are driving, the anti-lock brake system needs service and you do not have anti-lock brakes. The anti-lock brake system warning light should come on brieﬂy when you turn the ignition key to RUN. This is normal. If the light does not come on then, have it ﬁxed so it will be ready to warn you if there is a problem. If the warning light does not come on then, have it ﬁxed so it will be ready to warn you if there is a problem. If it stays on, or comes on when you are driving, there may be a problem with your traction control system and your vehicle may need service. When this warning light is on, the system will not limit wheel spin. Adjust your driving accordingly. If the traction control system warning light comes on and stays on for an extended period of time when the system is turned on, your vehicle needs service. See Traction Control System (TCS) on page 4-9 for more information. 3-32 Engine Coolant Temperature Warning Light Engine Coolant Temperature Gage The engine coolant temperature warning light will come on when the engine has overheated. If this happens you should pull over and turn off the engine as soon as possible. See Engine Overheating on page 5-29 for more information. Notice: Driving with the engine coolant temperature warning light on could cause your vehicle to overheat. See Engine Overheating on page 5-29. Your vehicle could be damaged, and it might not be covered by your warranty. Never drive with the engine coolant temperature warning light on. This light will also come on when starting your vehicle. If it doesn’t, have your vehicle serviced. United States Canada This gage shows the engine coolant temperature. If the gage pointer moves towards the “H” (United States) or the shaded in thermostat (Canada), it means that your engine coolant has overheated. If you have been operating your vehicle under normal driving conditions, you should pull off the road, stop your vehicle and turn off the engine as soon as possible. See Engine Overheating on page 5-29 for more information. 3-33 Tire Pressure Light If equipped, this light should come on brieﬂy as you start the engine. It will then come on only when a ﬂat or low tire pressure condition exists. See Tire Pressure Monitor System on page 5-62 for more information. Malfunction Indicator Lamp Check Engine Light Your vehicle is equipped with a computer which monitors operation of the fuel, ignition, and emission control systems. 3-34 If you keep driving your vehicle with this This system is called OBD II (On-Board Diagnostics-Second Generation) and is intended to assure that emissions are at acceptable levels for the life of the vehicle, helping to produce a cleaner environment. The check engine light comes on to indicate that there is a problem and service is required. Malfunctions often will be indicated by the system before any problem is apparent. This may prevent more serious damage to your vehicle. This system is also designed to assist your service technician in correctly diagnosing any malfunction. Notice: light on, after awhile, your emission controls may not work as well, your fuel economy may not be as good, and your engine may not run as smoothly. This could lead to costly repairs that may not be covered by your warranty. Notice: Modiﬁcations made to the engine, transaxle, exhaust, intake, or fuel system of your vehicle or the replacement of the original tires with other than those of the same Tire Performance Criteria (TPC) can affect your vehicle’s emission controls and may cause this light to come on. Modiﬁcations to these systems could lead to costly repairs not covered by your warranty. This may also result in a failure to pass a required Emission Inspection/Maintenance test. See Accessories and Modiﬁcations on page 5-3. This light should come on, as a check to show you it is working, when the ignition is on and the engine is not running. If the light does not come on, have it repaired. This light will also come on during a malfunction in one of two ways: Light Flashing — A misﬁre condition has been detected. A misﬁre increases vehicle emissions and may damage the emission control system on your vehicle. Diagnosis and service may be required. Light On Steady — An emission control system malfunction has been detected on your vehicle. Diagnosis and service may be required. If the Light is Flashing The following may prevent more serious damage to your vehicle: (cid:127) Reducing vehicle speed (cid:127) Avoiding hard accelerations (cid:127) Avoiding steep uphill grades If you are towing a trailer, reduce the amount of cargo being hauled as soon as it is possible If the light stops ﬂashing and remains on steady, see “If the Light Is On Steady” following. If the light continues to ﬂash, when it is safe to do so, stop the vehicle. Find a safe place to park your vehicle. Turn the key off, wait at least 10 seconds and restart the engine. If the light remains on steady, see “If the Light Is On Steady” following. If the light is still ﬂashing, follow the previous steps, and see your dealer for service as soon as possible. If the Light Is On Steady You may be able to correct the emission system malfunction by considering the following: Did you recently put fuel into your vehicle? If so, reinstall the fuel cap, making sure to fully install the cap. See Filling the Tank on page 5-8. The diagnostic system can determine if the fuel cap has been left off or improperly installed. A loose or missing fuel cap will allow fuel to evaporate into the atmosphere. A few driving trips with the cap properly installed should turn the light off. Did you just drive through a deep puddle of water? If so, your electrical system may be wet. The condition will usually be corrected when the electrical system dries out. A few driving trips should turn the light off. 3-35 (cid:127) (cid:127) (cid:127) Have you recently changed brands of fuel? If so, be sure to fuel your vehicle with quality fuel. See Gasoline Octane on page 5-5. Poor fuel quality will cause your engine not to run as efficiently as designed. You may notice this as stalling after start-up, stalling when you put the vehicle into gear, misﬁring, hesitation on acceleration, or stumbling on acceleration. (These conditions may go away once the engine is warmed up.) This will be detected by the system and cause the light to turn on. If you experience one or more of these conditions, change the fuel brand you use. It will require at least one full tank of the proper fuel to turn the light off. If none of the above steps have made the light turn off, your dealer can check the vehicle. Your dealer has the proper test equipment and diagnostic tools to ﬁx any mechanical or electrical problems that may have developed. Emissions Inspection and Maintenance Programs Some state/provincial and local governments have or may begin programs to inspect the emission control equipment on your vehicle. Failure to pass this inspection could prevent you from getting a vehicle registration. Here are some things you need to know to help your vehicle pass an inspection: Your vehicle will not pass this inspection if the check engine light is on or not working properly. Your vehicle will not pass this inspection if the OBD (on-board diagnostic) system determines that critical emission control systems have not been completely diagnosed by the system. The vehicle would be considered not ready for inspection. This can happen if you have recently replaced your battery or if your battery has run down. The diagnostic system is designed to evaluate critical emission control systems during normal driving. This may take several days of routine driving. If you have done this and your vehicle still does not pass the inspection for lack of OBD system readiness, your GM dealer can prepare the vehicle for inspection. 3-36 Oil Pressure Light {CAUTION: Do not keep driving if the oil pressure is low. If you do, your engine can become so hot that it catches ﬁre. You or others could be burned. Check your oil as soon as possible and have your vehicle serviced. Notice: Lack of proper engine oil maintenance may damage the engine. The repairs would not be covered by your warranty. Always follow the maintenance schedule in this manual for changing engine oil. This light tells you if there could be a problem with your engine oil pressure. The light goes on when you turn your key to RUN or START. It goes off once you start your engine. That is a check to be sure the light works. If it does not come on, be sure to have it ﬁxed so it will be there to warn you if something goes wrong. When the light comes on and stays on, it means that oil is not ﬂowing through your engine properly. You

Boost Classifieds - Car Advice, Reviews, Events & Classifieds

2006 Chevrolet Monte Carlo Owners Manual