2009 Chevrolet Malibu Owners Manual

Download PDF Manual
and a main storage. Pull up on the driver side latch to access the storage tray. Pull up on the passenger side latch to access the main storage. There is a removable divider and may be a storage pocket located at the rear of the center console. The armrest on top of the center console can be adjusted to a rearward, middle, and forward position. Pull or push the front of the armrest to adjust to the desired position. Another storage area is located in front of the main storage. Push down and then forward on the rear of the cover to access. There is a storage tray and removable cupholders. Storage Areas Glove Box Pull the handle up to open. Cupholders Removable cupholders are located in front of the center console. See “Center Console Storage Area” following for how to access them. Press and hold the tab at the rear of the cupholders and lift up and rearward to remove the cupholders. This will disengage the two forward tabs. To reinstall them, place the two forward tabs into the slots and push the rear of the cupholder down. For vehicles with rear seat cupholders, pull down the door on the back of the center console to access them. Instrument Panel Storage An instrument panel storage area, with a removable liner, is located above the radio. Slide the latch toward the back of the vehicle to open the storage area. 2-50 Driver Storage Compartment A driver storage compartment is located near the left side of the steering column on the bottom of the instrument panel. Pull the cover down to open. Pull out to remove for cleaning. Convenience Net Use the convenience net, located in the rear, to store small loads as far forward as possible. The net should not be used to store heavy loads. Sunroof On vehicles with a sunroof, the switch is located on the headliner between the map lamps. The sunroof only operates when the ignition is in ON/RUN, ACC/ACCESSORY, or if Retained Accessory Power (RAP) is active. See Retained Accessory Power (RAP) on page 2-23. Press and release the back of the switch to open the sunroof to the vent position. From the vent position, press and release the back of the switch to express-open the sunroof. To stop the sunroof from express opening, press the switch again. If the sunshade is closed, it will open automatically when the sunroof opens past the vented position. A deﬂector will automatically raise when the sunroof is opened. The deﬂector will retract when the sunroof is closed. To close the sunroof, press the front of the switch and hold it until the sunroof is closed. The sunroof will stop if the switch is released. Close the sunshade by hand. The sunroof glass panel cannot be opened or closed if the vehicle has an electrical failure. Notice: Forcing the sunshade forward of the sliding glass panel may cause damage and the sunroof may not operate properly. Always close the glass panel before closing the sunshade. 2-51 ✍ NOTES 2-52 Section 3 Instrument Panel Instrument Panel Overview ...............................3-4 Hazard Warning Flashers ................................3-6 Horn .............................................................3-6 Tilt and Telescopic Steering Wheel ...................3-6 Turn Signal/Multifunction Lever .........................3-7 Turn and Lane-Change Signals ........................3-7 Headlamp High/Low-Beam Changer ..................3-8 Flash-to-Pass .................................................3-8 Windshield Wipers ..........................................3-8 Windshield Washer .........................................3-9 Cruise Control ..............................................3-10 Headlamps ..................................................3-13 Headlamps on Reminder ................................3-14 Headlamps Off in Park ..................................3-14 Delayed Headlamps ......................................3-14 Daytime Running Lamps (DRL) .......................3-14 Automatic Headlamp System ..........................3-15 Fog Lamps ..................................................3-15 Instrument Panel Brightness ...........................3-16 Dome Lamps ...............................................3-16 Entry/Exit Lighting .........................................3-16 Parade Dimming ...........................................3-16 Reading Lamps ............................................3-16 Electric Power Management ...........................3-17 Battery Run-Down Protection ..........................3-18 Accessory Power Outlet(s) .............................3-18 Power Outlet 115 Volt Alternating Current ........3-19 Climate Controls ............................................3-20 Climate Control System .................................3-20 Automatic Climate Control System ...................3-24 Outlet Adjustment .........................................3-27 Warning Lights, Gages, and Indicators ............3-28 Instrument Panel Cluster ................................3-29 Speedometer and Odometer ...........................3-30 Trip Odometer ..............................................3-30 Tachometer .................................................3-30 Safety Belt Reminders ...................................3-30 Airbag Readiness Light ..................................3-31 Passenger Airbag Status Indicator ...................3-32 Charging System Light ..................................3-33 Brake System Warning Light ..........................3-34 Antilock Brake System (ABS) Warning Light .....3-35 Electronic Stability Control (ESC)/Traction Control System (TCS) Indicator/Warning Light ........................................................3-35 3-1 Section 3 Instrument Panel Engine Coolant Temperature Warning Light ......3-36 Engine Coolant Temperature Gage ..................3-37 Tire Pressure Light .......................................3-37 Malfunction Indicator Lamp .............................3-38 Oil Pressure Light .........................................3-41 Security Light ...............................................3-41 Cruise Control Light ......................................3-42 Highbeam On Light .......................................3-42 Fuel Gage ...................................................3-42 Driver Information Center (DIC) .......................3-43 DIC Operation and Displays ...........................3-44 DIC Warnings and Messages .........................3-46 DIC Vehicle Personalization ............................3-50 Audio System(s) .............................................3-56 Setting the Clock ..........................................3-57 Radio(s) ......................................................3-59 Using an MP3 ..............................................3-71 XM Radio Messages .....................................3-77 Bluetooth® ...................................................3-78 Theft-Deterrent Feature ..................................3-89 Audio Steering Wheel Controls .......................3-89 Radio Reception ...........................................3-91 Backglass Antenna .......................................3-92 XM™ Satellite Radio Antenna System .............3-92 Chime Level Adjustment ................................3-92 3-2 ✍ NOTES 3-3 Instrument Panel Overview 3-4 The main components of the instrument panel are the following: A. Outlet Adjustment on page 3-27. B. Turn Signal/Multifunction Lever on page 3-7. C. Driver Shift Control (If Equipped). Automatic Transmission Operation (Four Speed Transmission) on page 2-26 or Automatic Transmission Operation (Six Speed Transmission) on page 2-28. D. Instrument Panel Cluster on page 3-29. E. Windshield Wipers on page 3-8 and Windshield Washer on page 3-9. F. Instrument Panel Storage on page 2-50. G. Audio System(s) on page 3-56. H. Instrument Panel Brightness on page 3-16. Fog Lamps on page 3-15. I. Driver Storage Compartment on page 2-51. J. Hood Release on page 5-14. K. Cruise Control on page 3-10. Driver Information Center (DIC) on page 3-43. L. Tilt and Telescopic Steering Wheel on page 3-6. M. Horn on page 3-6. N. Audio Steering Wheel Controls on page 3-89 (If Equipped). O. Ignition Positions on page 2-22. P. Climate Control System on page 3-20 or Automatic Climate Control System on page 3-24. Q. Hazard Warning Flashers on page 3-6. R. Shift Lever. See Automatic Transmission Operation (Four Speed Transmission) on page 2-26 or Automatic Transmission Operation (Six Speed Transmission) on page 2-28. S. Front Storage Area on page 2-50. Accessory Power Outlet(s) on page 3-18. T. Passenger Airbag Status Indicator on page 3-32. U. Traction Control System (TCS) on page 4-8. V. Glove Box on page 2-50. 3-5 Tilt and Telescopic Steering Wheel A tilt and telescope wheel lets the steering wheel be adjusted. Hazard Warning Flashers | (Hazard Warning Flasher): Press this button located on the instrument panel, to make the front and rear turn signal lamps ﬂash on and off. This warns others that you are having trouble. Press | again to turn the ﬂashers off. Horn Press near or on the horn symbols on the steering wheel pad to sound the horn. The lever is located on the left side of the steering column. To tilt and telescope the steering wheel, pull down the lever. Then move the steering wheel up or down or backward or forward into a comfortable position. Pull the lever up to lock the steering wheel in place. Do not adjust the steering wheel while driving. 3-6 Turn Signal/Multifunction Lever Turn and Lane-Change Signals An arrow on the instrument panel cluster ﬂashes in the direction of the turn or lane change. The lever on the left side of the steering column includes the following: G : Turn and Lane-Change Signals 5 3 : Headlamp High/Low-Beam Changer O : Exterior Lamp Control Flash-to-Pass. Information for these features is on the pages following. Move the lever all the way up or down to signal a turn. Raise or lower the lever until the arrow starts to ﬂash to signal a lane change. Hold it there until lane change is complete. The lever returns to its starting position when it is released. If after signaling a turn or lane change the arrows ﬂash rapidly or do not come on, a signal bulb could be burned out. Have the bulbs replaced. If the bulb is not burned out, check the fuse. See Fuses on page 5-99. 3-7 Headlamp High/Low-Beam Changer To change the headlamps from low beam to high beam, push the turn signal/multifunction lever away from you. This instrument panel cluster light 3 comes on if the high beam lamps are turned on while the ignition is in ON/RUN. To change the headlamps from high beam to low beam, pull the turn signal lever toward you. Flash-to-Pass This feature lets the high-beam headlamps be used to signal a driver in front of you that you want to pass. Pull the turn signal/multifunction lever toward you until the high-beam headlamps come on, then release the lever to turn them off. 3-8 Windshield Wipers The windshield wiper lever is located on the right side of the steering wheel. Move the lever to control the windshield wipers. 9 (Off): Turns off the windshield wipers. & (Intermittent; Speed Sensitive Wipers): For intermittent or speed sensitive operation. The amount of delay time varies between wiping cycles due to the delay setting selected or the speed of the vehicle. As vehicle speed is increased or decreased, the wiper interval also increases or decreases. x (Delay): While the lever is in the intermittent position, turn the intermittent adjust band with this symbol on it up or down to select a shorter or longer delay between wiping cycles. To the left of the adjust band are bars, increasing in size from bottom to top, that indicate the frequency of the wipes. Smaller bars mean the wipers movement is less frequent. Larger bars mean the movement is more frequent. 6 (Low Speed): For steady wiping at low speed. 1 (High Speed): For wiping at a high speed. 8 (Mist): Move the lever all the way down for a single wiping cycle. Hold it there until the windshield wipers start; then release. The wipers stop after one wiping cycle. Hold the lever down longer, for more wipe cycles. Clear ice and snow from the wiper blades before using them. If the wiper blades are frozen to the windshield, carefully loosen or thaw them. If they become damaged, install new blades. Heavy snow or ice can overload the wiper motor. A circuit breaker stops the motor until it cools. If the motor gets stuck, turn the wipers off, clear away the snow or ice, and then turn the wipers back on. As an added safety feature, if the wipers are on for more than 15 seconds, the vehicle’s headlamps turn on automatically. They turn off 15 seconds after the wipers are turned off. Windshield Washer Press the button at the end of the windshield wiper lever until the washers begin. { CAUTION: In freezing weather, do not use your washer until the windshield is warmed. Otherwise the washer ﬂuid can form ice on the windshield, blocking your vision. When the button is released, the washers stop, but the wipers continue to wipe about three times or resume the previous speed. 3-9 Cruise Control Cruise control lets a speed of about 25 mph (40 km/h) or more be maintained without keeping your foot on the accelerator. This can really help on long trips. Cruise control does not work at speeds below 25 mph (40 km/h). { CAUTION: Cruise control can be dangerous where you cannot drive safely at a steady speed. So, do not use the cruise control on winding roads or in heavy traffic. Cruise control can be dangerous on slippery roads. On such roads, fast changes in tire traction can cause excessive wheel slip, and you could lose control. Do not use cruise control on slippery roads. Setting Cruise Control { CAUTION: If you leave your cruise control on when you are not using cruise, you might hit a button and go into cruise when you do not want to. You could be startled and even lose control. Keep the cruise control switch off until you want to use cruise control. 3-10 The cruise control buttons are located on the steering wheel. To set a speed do the following: 1. Press I to turn cruise control on. The indicator light on the button comes on. 2. Get up to the desired speed. 3. Press the SET− and release it. The cruise symbol displays in the instrument panel cluster to show the system is engaged. 4. Take your foot off the accelerator pedal. When the brakes are applied, the cruise control shuts off. If the vehicle is in cruise control and the Traction Control System (TCS) or Enhanced Traction System (ETS) begins to limit wheel spin, the cruise control automatically disengages. See Traction Control System (TCS) on page 4-8 and Electronic Stability Control (ESC) on page 4-6. When road conditions allow, the cruise control can be used again. I (On/Off): Press to turn the cruise control system on and off. RES+ (Resume): Press to resume a set speed and to accelerate the speed. SET− (Set): Press to set a speed and to decrease the speed. 3-11 Resuming a Set Speed If the cruise control is set at a desired speed and then the brakes are applied, the cruise control is disengaged. The cruise symbol in the instrument panel cluster also goes out indicating cruise is no longer engaged. To return to the previously set speed, you do not need to repeat the set process again. Once at a speed of about 25 mph (40 km/h) or more, brieﬂy press the RES+. This takes the vehicle back up to the previously chosen speed and stays there. Increasing Speed While Using Cruise Control There are two ways to go to a higher speed. If the cruise control system is already engaged, press the RES+. Hold it there until the desired speed is reached and then release the button. To increase the vehicle speed in very small amounts, brieﬂy press the RES+ and then release it. Each time this is done, the vehicle goes about 1 mph (1.6 km/h) faster. Reducing Speed While Using Cruise Control If the cruise control system is already engaged: (cid:129) Push and hold the SET− until the desired lower speed is reached, then release it. To slow down in very small amounts, brieﬂy push the SET−. Each time this is done, the vehicle goes about 1 mph (1.6 km/h) slower. Passing Another Vehicle While Using Cruise Control Use the accelerator pedal to increase the vehicle’s speed. When you take your foot off the pedal, the vehicle slows down to the previously set cruise control speed. Using Cruise Control on Hills How well the cruise control works on hills depends upon the vehicle’s speed, load, and the steepness of the hills. When going up steep hills, you might have to step on the accelerator pedal to maintain the vehicle’s speed. When going downhill, you might have to brake or shift to a lower gear to keep the vehicle at a lower speed. When the brakes are applied this ends the cruise control. 3-12 (cid:129) (cid:129) (cid:129) Ending Cruise Control There are two ways to disengage the cruise control: (cid:129) Step lightly on the brake pedal to disengage the cruise control. (cid:129) Press the on/off button, to turn off the cruise control. Erasing Speed Memory The cruise control set speed memory is erased when the cruise control or the ignition are turned off. Headlamps The exterior lamp control has the following four positions: 2 (Headlamps): Turns on the headlamps, parking lamps, and taillamps. ; (Parking Lamps): Turns on the parking lamps and taillamps only. AUTO (Automatic Headlamp System): Automatically turns on the Daytime Running Lamps during daytime, and the headlamps, parking lamps, and taillamps at night. P (Off/On): Turn the band to this position to turn on the Automatic Headlamp System. In Canada, this position only works when a vehicle is in the P (Park) position. To turn on the Automatic Headlamp System, turn the switch to off/on. To turn them off, turn the switch to off/on again. This is a momentary control switch that springs back when released. The Automatic Headlamp System always turns on at the beginning of an ignition cycle. The band on the lever on the outboard side of the steering column operates the exterior lamps. 3-13 Headlamps on Reminder If the driver’s door is opened and the ignition is turned off while leaving the lamps on, a warning chime will sound. Headlamps Off in Park This feature works when the ignition is in the ON/RUN position and it is dark outside. To turn the headlamps off when it is dark outside but keep other exterior lights on, turn the exterior lamp control to the parking lamp position. To turn on the headlamps along with the other lamps when it is dark outside, turn the exterior lamp control to the AUTO or headlamp position. This function does not work for vehicles ﬁrst sold in Canada. Delayed Headlamps The delayed headlamps feature keeps the headlamps on for 20 seconds after the key is turned to LOCK/OFF, then the headlamps automatically turn off. To override the 20 second delayed headlamp feature while it is active turn the turn signal/multifunction lever up one position and then back to AUTO. 3-14 Daytime Running Lamps (DRL) Daytime Running Lamps (DRL) can make it easier for others to see the front of your vehicle during the day. Fully functional DRL are required on all vehicles ﬁrst sold in Canada. The vehicle has a light sensor on top of the instrument panel that controls the DRL. Do not cover this sensor or the head lamps will be on when they are not needed. The DRL system makes the low-beam headlamps come on at a reduced brightness when the following conditions are met: The ignition is on. The exterior lamps control is in AUTO. The exterior lamps control is in the parking lamps only position (This applies only to vehicles that are ﬁrst sold in Canada). The light sensor detects daytime light. The parking brake is released or the vehicle is not in P (Park). When the DRL system is on, the taillamps, sidemarker lamps, parking lamps, and instrument panel lights are not on unless you turn the exterior lamps control to the parking lamp position. The regular headlamp system should be turned on when they are needed. (cid:129) (cid:129) (cid:129) (cid:129) (cid:129) Automatic Headlamp System When it is dark enough outside, the automatic headlamp system turns on the headlamps at the normal brightness along with other lamps such as the taillamps, sidemarker, parking lamps, and the instrument panel lights. The radio lights will also be dim. The vehicle has a light sensor on top of the instrument panel that controls the automatic headlamp system. Do not cover the sensor or the automatic headlamp system will turn on when it is not needed. There is a delay in the transition between the daytime and nighttime operation of the DRL and the automatic headlamp systems so that driving under bridges or bright overhead street lights does not affect the system. The DRL and automatic headlamp systems will only be affected when the light sensor sees a change in lighting lasting longer than this delay. If vehicle is started in a dark garage, the automatic headlamp system comes on immediately. Once the vehicle leaves the garage, it takes about one minute for the automatic headlamp system to change to DRL if it is light outside. During that delay, the instrument panel cluster may not be as bright as usual. Make sure the instrument panel brightness control is in the full bright position. See Instrument Panel Brightness on page 3-16. To idle the vehicle with the automatic headlamp system off, turn the ignition on and set the exterior light switch to the off/on position. For vehicles ﬁrst sold in Canada, the transmission must stay in P (Park) for this function. The regular headlamps should be used when needed. Fog Lamps For vehicles with fog lamps, the button for this feature is located on the instrument panel, to the left of the steering wheel. The ignition must be on for the fog lamps to work. # : Press to turn the fog lamps on or off. An indicator light comes on when the fog lamps are on. The parking lamps automatically turn on and off when the fog lamps are turned on and off. The fog lamps turn off while the high-beam headlamps are turned on. Some localities have laws that require the headlamps to be on along with the fog lamps. 3-15 Instrument Panel Brightness The knob with this symbol is located on the instrument panel to the left of the steering column. Turn the knob clockwise or counterclockwise to brighten or dim the lights. Turn the knob completely clockwise to turn on the interior lamps. Dome Lamps The dome lamps come on when any door is opened. They turn off after all the doors are closed. The dome lamps can also be turned on by turning the instrument panel brightness knob, located on the instrument panel to the left of the steering column, clockwise to the farthest position. In this position, the dome lamps remain on whether a door is opened or closed. Entry/Exit Lighting The lamps inside the vehicle come on when any door is opened. These lamps fade out about 20 seconds after all of the doors have been closed or when the ignition is turned to ON/RUN. They also come on when the unlock symbol button or the horn symbol is pressed on the Remote Keyless Entry (RKE) system transmitter. The lamps inside the vehicle stay on for about 20 seconds after the key is removed from the ignition to provide light as you exit. Parade Dimming Parade dimming is a separate lighting mode that comes on while the parking lamps are turned on during the day. It prevents the display lights and indicator lights from being dim, while the parking lamps are used during the day. Reading Lamps For vehicles with front and rear reading lamps, press the lens to turn the lamp on and off, while the doors are closed. These lamps come on automatically when any door is opened. 3-16 Electric Power Management The vehicle has Electric Power Management (EPM) that estimates the battery’s temperature and state of charge. It then adjusts the voltage for best performance and extended life of the battery. When the battery’s state of charge is low, the voltage is raised slightly to quickly bring the charge back up. When the state of charge is high, the voltage is lowered slightly to prevent overcharging. If the vehicle has a voltmeter gage or a voltage display on the Driver Information Center (DIC), you may see the voltage move up or down. This is normal. If there is a problem, an alert will be displayed. The battery can be discharged at idle if the electrical loads are very high. This is true for all vehicles. This is because the generator (alternator) may not be spinning fast enough at idle to produce all the power that is needed for very high electrical loads. A high electrical load occurs when several of the following are on, such as: headlamps, high beams, fog lamps, rear window defogger, climate control fan at high speed, heated seats, engine cooling fans, trailer loads, and loads plugged into accessory power outlets. EPM works to prevent excessive discharge of the battery. It does this by balancing the generator’s output and the vehicle’s electrical needs. It can increase engine idle speed to generate more power, whenever needed. It can temporarily reduce the power demands of some accessories. Normally, these actions occur in steps or levels, without being noticeable. In rare cases at the highest levels of corrective action, this action may be noticeable to the driver. If so, a Driver Information Center (DIC) message might be displayed, such as BATTERY SAVER ACTIVE, BATTERY VOLTAGE LOW, or LOW BATTERY. If this message is displayed, it is recommended that the driver reduce the electrical loads as much as possible. See DIC Warnings and Messages on page 3-46. 3-17 Battery Run-Down Protection The vehicle has a battery run-down protection feature designed to protect the vehicle’s battery. When any interior lamp (trunk, reading, or visor vanity) is left on while the ignition is turned off, the battery run-down protection system will automatically shut the lamp(s) off after 20 minutes. This will avoid draining the battery. To reactivate the interior lamps, do one of the following: Turn on the ignition. Turn the exterior lamp control off and then on. (cid:129) Open a door. (cid:129) Press any Remote Keyless Entry (RKE) transmitter button (if equipped). (cid:129) Press the remote trunk release button. (cid:129) Press the power door lock switch. The battery run-down feature will also be activated when any door on the vehicle is left open and the ignition is in LOCK/OFF. Accessory Power Outlet(s) Accessory power outlets can be used to connect auxiliary electrical equipment, such as a cellular telephone. There are two accessory power outlets. One accessory power outlet is located inside the storage bin below the climate controls and the other outlet is on the rear of the center storage console. To use an outlet, lift the protective cap. When not in use, always cover the outlet with the protective cap. The accessory power outlet is operational at all times. Notice: Leaving electrical equipment plugged in for an extended period of time while the vehicle is off will drain the battery. Power is always supplied to the outlets. Always unplug electrical equipment when not in use and do not plug in equipment that exceeds the maximum 20 ampere rating. Certain electrical accessories may not be compatible with the accessory power outlet and could result in blown vehicle or adapter fuses. If you experience a problem, see your dealer/retailer for additional information on the accessory power outlet. 3-18 (cid:129) (cid:129) Notice: Adding any electrical equipment to your vehicle can damage it or keep other components from working as they should. The repairs would not be covered by your warranty. Do not use equipment exceeding maximum amperage rating of 20 amperes. Check with your dealer/retailer before adding electrical equipment. When adding electrical equipment, be sure to follow the proper installation instructions included with the equipment. Notice: damage not covered by the warranty. Do not hang any type of accessory or accessory bracket from the plug because the power outlets are designed for accessory power plugs only. Improper use of the power outlet can cause Power Outlet 115 Volt Alternating Current The vehicle may have a power outlet that can be used to plug in electrical equipment that uses a maximum limit of 150 watts. The power outlet is located on the rear of the center console. An indicator light on the outlet turns on to show it is in use. The light comes on when the ignition is in ON/RUN and equipment requiring less than 150 watts is plugged into the outlet, and no system fault is detected. The indicator light does not come on when the ignition is in LOCK/OFF or if no equipment is plugged into the outlet. 3-19 If you try to connect equipment using more than 150 watts or a system fault is detected, a protection circuit shuts off the power supply and the indicator light turns off. To reset the circuit, unplug the item and plug it back in or turn the Remote Accessory Power (RAP) off and then back on. See Retained Accessory Power (RAP) on page 2-23. The power restarts when equipment that operates within the limit is plugged into the outlet and a system fault is not detected. The power outlet is not designed for the following electrical equipment and may not work properly if these items are plugged into the power outlet: (cid:129) Equipment with high initial peak wattage such as: compressor-driven refrigerators and electric power tools. (cid:129) Other equipment requiring an extremely stable power supply such as: microcomputer-controlled electric blankets, touch sensor lamps, etc. 3-20 Climate Controls Climate Control System The heating, cooling and ventilation for the vehicle can be controlled with this system. A. Fan Control B. Recirculation C. Temperature Control D. Outside Air E. Air Delivery Mode Control F. Air Conditioning G. Rear Window Defogger Operation Temperature Control: Turn clockwise or counterclockwise to increase or decrease the temperature inside the vehicle. When it is cold outside 0°F (−18°C) or lower, use the engine coolant heater, if vehicle has one, to provide warmer air faster to the vehicle. An engine coolant heater warms the coolant the engine uses that provides heat to warm the inside of the vehicle. For more information, see Engine Coolant Heater on page 2-25. 9 (Fan Control): Turn clockwise or counterclockwise to increase or decrease the fan speed. The fan must be on to run the air-conditioning compressor. Air Delivery Mode Control: Turn clockwise or counterclockwise to change the current airﬂow mode. Select from the following: H (Vent): Air is directed to the instrument panel outlets. ) (Bi-Level): Air is divided between the instrument panel and ﬂoor outlets. Some air will be directed toward the side windows. 6 (Floor): Air is directed to the ﬂoor outlets with some air directed to the windshield and side window outlets. - (Defog): This mode clears the windows of fog or moisture. Air is directed to the windshield and ﬂoor outlets, with some air directed to the side windows. When this mode is selected, the system automatically turns off recirculation and runs the air-conditioning compressor unless the outside temperature is at or below freezing. The air-conditioning compressor operates although the indicator light is not on. The air-conditioning indicator light turns off when defog is selected. If the air-conditioning button is pressed while in defog mode, the indicator light will turn on. If the button is pressed again, the light will turn off. The recirculation mode cannot be selected while in the defog mode. Do not drive the vehicle until all the windows are clear. 1 (Defrost): This mode quickly clears the windshield of fog or frost. Air is directed to the windshield with some air directed to the ﬂoor vents. In this mode, outside air is pulled into the vehicle. The air-conditioning compressor will not run unless the outside temperature is at or below freezing. The air-conditioning compressor operates although the indicator light is not on. The air-conditioning indicator light turns off when defrost is selected. If the air-conditioning button is pressed while in defrost mode, the indicator light turns on. If the button is pressed again, the light turns off. Recirculation cannot be selected while in the defrost mode. 3-21 To help clear the windshield quickly, do the following: 1. Select 0 . 2. Select the highest temperature. 3. Select the highest fan speed. # (Air Conditioning): Press to turn the air conditioning system on or off. An indicator light comes on to show it is on. The air-conditioning system removes moisture from the air, so a small amount of water might drip under the vehicle while it is idling or after the engine is turned off is normal. Maximum Air Conditioning On hot days, open the windows to let hot inside air escape; then close them. This helps reduce the time it takes for the vehicle to cool down. It also helps the air conditioning system operate more efficiently. For quick cool down on hot days, do the following: 1. Select the C vent mode. 2. Select the highest fan speed. 3. Select # air conditioning. 4. Select the ? recirculation mode. 5. Select the coolest temperature. 3-22 Using these settings together for long periods of time can cause the air inside of the vehicle to become too dry. To prevent this from happening, after the air in the vehicle has cooled, turn the recirculation mode off. : (Outside Air): Press to turn the outside air mode on. An indicator light comes on to show that it is on. Air from outside the vehicle will circulate throughout the vehicle. The outside air mode can be used with all modes, but it cannot be used with the recirculation mode. Press : to cancel the recirculation mode. ? (Recirculation): Press to turn the recirculation mode on. An indicator light comes on to show that it is on. This mode recirculates and helps to quickly cool the air inside the vehicle. It can be used to prevent outside air and odors from entering the vehicle. The recirculation indicator light blinks three times if you try to use recirculation in a mode in which it cannot function. Pressing this button cancels the outside air mode. When switching to the defog or defrost modes the system automatically moves from recirculation to outside air. When the vehicle or fan is turned off and back on, the system defaults to outside air automatically. Only use recirculation mode when it is needed for comfort, since window fogging can occur. Rear Window Defogger The rear window defogger uses a warming grid to remove fog or frost from the rear window. < REAR: Press to turn the rear window defogger on or off. An indicator light comes on to show that the rear window defogger is on. Be sure to clear as much snow from the rear window as possible. If driving below 50 mph (80 km/h), the rear window defogger turns off about 15 minutes after the button is pressed. If turned on again, the defogger only runs for about seven minutes before turning off. The defogger can also be turned off by turning off the engine. If the vehicle’s speed is maintained above 50 mph (80 km/h), the rear window defogger remains on once the button is pressed. If the vehicle has heated outside mirrors, the surface of the outside mirrors heat when the rear window defogger is activated. See Outside Power Mirrors on page 2-39. Notice: Do not use anything sharp on the inside of the rear window. If you do, you could cut or damage the warming grid, and the repairs would not be covered by the vehicle warranty. Do not attach a temporary vehicle license, tape, a decal or anything similar to the defogger grid. Remote Start Climate Control Operation For vehicles with the remote start feature, when it is activated the climate control system heats or cools the inside of the vehicle using the modes that were set before the vehicle was turned off. The climate control knobs will remain active during a remote start. However, the climate control buttons will be inactive until the ignition is turned on by the key. If the fan is off, the climate control system will not operate during remote start. See Remote Keyless Entry (RKE) System Operation on page 2-5. 3-23 Automatic Climate Control System For vehicles with this system, the heating, cooling, and ventilation can be automatically controlled. A. Fan Control B. Air Conditioning C. Recirculation D. Outside Air E. Rear Window Defogger F. Air Delivery Mode Control G. Display H. Temperature Control 3-24 Automatic Operation AUTO (Automatic): Select AUTO on both the fan speed control and the air delivery mode control knobs to activate the automatic system. When automatic operation is active the system controls the inside temperature and air delivery. To place the system in automatic mode do the following: 1. Turn the fan knob and the mode knob to the AUTO position. The current set temperature displays. When AUTO is selected, the air conditioning operation and air inlet is automatically controlled. The air conditioning compressor runs while the outside temperature is over about 40°F (4°C). The air inlet will normally be set to outside air. If it is hot outside, the air inlet may automatically switch to recirculate inside air to help quickly cool down the vehicle. 2. Set the temperature. An initial setting of 73°F (23°C) is recommended. Allow about 20 minutes for the system to regulate. Press w or x to adjust the temperature setting as necessary. If the temperature is set at 60°F (15°C) the system remains at the maximum cooling setting. If the temperature is set at 90°F (32°C) the system remains at the maximum heat setting. Choosing either maximum setting does not cause the vehicle to heat or cool any faster. Do not to cover the sensor located on the top of the instrument panel near the windshield. This sensor regulates air temperature based on the intensity of the sun. Also do not cover the sensor grille on the lower right side of the climate control faceplate, as this regulates the inside temperature. To avoid blowing cold air at engine start-up in cold weather, the system delays turning on the fan until warm air is available. The length of delay depends on the engine coolant temperature. Turning the fan knob overrides this delay and changes the fan to the selected speed. Manual Operation 9 (Off): Select this position on the fan knob to turn off the entire climate control system. Outside air still enters the vehicle. The airﬂow direction and temperature can be adjusted. x / w Temperature Control: Press the arrows to increase or decrease the temperature inside the vehicle. 9 (Fan Control): Turn clockwise or counterclockwise to increase or decrease the fan speed. Select from the following: H (Vent): Air is directed to the instrument panel outlets. ) (Bi-Level): Air is divided between the instrument panel outlets and the ﬂoor outlets. 6 (Floor): Air is directed to the ﬂoor outlets with some air directed to the side window outlets. - (Defog): This mode clears the windows of fog or moisture. Air is directed to the ﬂoor and windshield outlets. 0 (Defrost): This mode clears the windows of fog or frost more quickly. The system automatically controls the fan speed if defrost is selected from the AUTO mode. If the outside temperature is 40°F (4°C) or warmer, the air conditioning compressor automatically runs to help dehumidify the air and dry the windshield. The air conditioning indicator light blinks three times if the compressor is turned off while in this mode. # (Air Conditioning): Press turn the air conditioning on and off. An indicator light turns on to show the air conditioning is on. Air Delivery Mode Control: Turn clockwise or counterclockwise to change the direction of the airﬂow in the vehicle. When air conditioning is selected or is in AUTO mode, the system runs the air conditioning automatically to cool and dehumidify the air entering the vehicle. 3-25 h (Recirculation): Press to turn the recirculation mode on. An indicator light above the button comes on to show it is on. This mode recirculates and helps to quickly cool the air inside the vehicle. It can be used to help prevent outside air and odors from entering the vehicle. The recirculation indicator light blinks three times if you try to use recirculation in a mode in which it cannot function. Pressing this button cancels the auto recirculation feature. Each time the vehicle is started, the system reverts to the auto recirculation function. The recirculation mode cannot be used with the ﬂoor, defrost, or defog modes. If recirculation is selected in these modes, the indicator ﬂashes three times and turns off to indicate that this is not allowed. This is to prevent window fogging. When the weather is cool or damp, operating the system in recirculation for extended periods of time can cause fogging of the vehicle’s windows. To clear the fog, select either defog or defrost. Make sure the air conditioning is on. Allow the air conditioning to run automatically to help dehumidify the air. On hot days, open the windows long enough to let hot inside air escape. This reduces the time it takes for the vehicle to cool down. Then keep the windows closed for the air conditioner to work its best. On cool, but sunny days while using manual operation of the automatic system, use bi-level to deliver warm air to the ﬂoor and cooler air to the instrument panel outlets. To warm or cool the air delivered, press the temperature buttons to the desired setting. In AUTO mode the system cools and dehumidiﬁes the air inside the vehicle. Also while in AUTO mode, the system maximizes its performance by using recirculation as necessary. Heating: On cold days when using manual operation of the automatic system, use ﬂoor mode to deliver air to the ﬂoor outlets. To warm or cool the air delivered, press x or w to the desired temperature setting. To use the automatic mode, turn the knob to AUTO and press x or w to adjust the temperature. : (Outside Air): Press to turn the outside air mode on. An indicator light comes on to show it is on. Air from outside the vehicle will circulate throughout the vehicle. The outside air mode can be used with all modes, but it cannot be used with the recirculation mode. Pressing this button cancels the recirculation mode. 3-26 Rear Window Defogger The rear window defogger uses a warming grid to remove fog from the rear window. < (Rear): Press to turn the rear window defogger on or off. An indicator light comes on to show that the rear window defogger is on. If driving below 50 mph (80 km/h), the rear window defogger turns off about 15 minutes after the button is pressed. If additional warming time is needed, press the button again. If the vehicle’s speed is maintained above 50 mph (80 km/h), the rear window defogger remains on once the button is pressed. For vehicles with heated outside mirrors, the surface of the outside mirrors will also heat when the rear window defogger is activated. See Outside Power Mirrors on page 2-39. Notice: Do not use a razor blade or sharp object to clear the inside rear window. Do not adhere anything to the defogger grid lines in the rear glass. These actions may damage the rear defogger. Repairs would not be covered by your warranty. Remote Start Climate Control Operation For vehicles with remote start, when it is activated the climate control system heats and cools the inside of the vehicle using the previous system settings before the vehicle was turned off. The climate control knobs will remain active during a remote start. However, the climate control buttons will be inactive until the ignition is turned on by the key. If the fan is off, the climate control system will not operate during remote start. With the automatic climate control system, the climate control displays “RS” in place of the temperature to indicate that remote start is activated. For best performance, turn both the fan and mode knobs to AUTO. If the temperature is cold enough and the mode knob is set to AUTO, the system begins in defrost to clear the windows. See Remote Keyless Entry (RKE) System Operation on page 2-5. Outlet Adjustment Use the lever located in the center of each outlet by moving it either up and down or side-to-side, to change the direction and amount of airﬂow in the vehicle. 3-27 Operation Tips (cid:129) Clear away any ice, snow, or leaves from the air inlets at the base of the windshield that may block the ﬂow of air into the vehicle. (cid:129) Do not use non-GM approved hood deﬂectors as they could adversely affect the performance of the system. (cid:129) Keep the path under the front seats clear of objects to help circulate the air inside of the vehicle more effectively. (cid:129) When an objectionable odor outside the vehicle is encountered, use the recirculation mode, with the temperature knob at a comfortable setting to prevent the odor from entering the vehicle through the ventilation system. This can be helpful when driving through a long tunnel with poor ventilation. However, extended usage of this mode in cold or cool weather can cause window fogging. Warning Lights, Gages, and Indicators Warning lights and gages can signal that something is wrong before it becomes serious enough to cause an expensive repair or replacement. Paying attention to the warning lights and gages could prevent injury. Warning lights come on when there may be or is a problem with one of the vehicle’s functions. Some warning lights come on brieﬂy when the engine is started to indicate they are working. Gages can indicate when there may be or is a problem with one of the vehicle’s functions. Often gages and warning lights work together to indicate a problem with the vehicle. When one of the warning lights comes on and stays on while driving, or when one of the gages shows there may be a problem, check the section that explains what to do. Follow this manual’s advice. Waiting to do repairs can be costly and even dangerous. 3-28 Instrument Panel Cluster The instrument panel cluster is designed to show how the vehicle is running. It shows how fast the vehicle is going, how much fuel the vehicle has used, and many other things needed to drive safely and economically. United States Base version shown, Canada Similar 3-29 Speedometer and Odometer The speedometer shows the vehicle speed in both miles per hour (mph) and kilometers per hour (km/h). The odometer shows how far the vehicle has been driven, in either miles (used in the United States) or kilometers (used in Canada). This vehicle has a tamper resistant odometer. The digital odometer will read 999,999 if it is turned back. If the vehicle needs a new odometer installed, it must be set to the mileage total of the old odometer. If that is not possible, then it must be set at zero and a label must be put on the driver door to show the old mileage reading when the new odometer was installed. Trip Odometer The trip odometer can show how far the vehicle has been driven since the odometer was last reset. The trip odometer is accessed and reset through the Driver Information Center (DIC). See DIC Operation and Displays on page 3-44 for more information. Tachometer The tachometer shows the engine speed in revolutions per minute (rpm). Safety Belt Reminders Safety Belt Reminder Light When the engine is started, a chime sounds for several seconds to remind a driver to fasten the safety belt, unless the driver safety belt is already buckled. The safety belt light comes on and stays on for several seconds, then ﬂashes for several more. This chime and light are repeated if the driver remains unbuckled and the vehicle is in motion. If the driver safety belt is already buckled, neither the chime nor the light comes on. 3-30 Passenger Safety Belt Reminder Light Several seconds after the engine is started, a chime sounds for several seconds to remind the front passenger to buckle their safety belt. This only occurs if the passenger airbag is enabled. See Passenger Sensing System on page 1-66 for more information. The passenger safety belt light, located on the instrument panel, comes on and stays on for several seconds and then ﬂashes for several more. This chime and light are repeated if the passenger remains unbuckled and the vehicle is in motion. The front passenger safety belt warning light and chime may turn on if an object is put on the seat such as a briefcase, handbag, grocery bag, laptop or other electronic device. To turn off the warning light and or chime, remove the object from the seat or buckle the safety belt. Airbag Readiness Light The system checks the airbag’s electrical system for possible malfunctions. If the light stays on it indicates there is an electrical problem. The system check includes the airbag sensor, the pretensioners, the airbag modules, the wiring and the crash sensing and diagnostic module. For more information on the airbag system, see Airbag System on page 1-58. If the passenger safety belt is buckled, neither the chime nor the light comes on. 3-31 The airbag readiness light ﬂashes for a few seconds when the engine is started. If the light does not come on then, have it ﬁxed immediately. Passenger Airbag Status Indicator The vehicle has a passenger sensing system. See Passenger Sensing System on page 1-66 for important safety information. The instrument panel has a passenger airbag status indicator. { CAUTION: If the airbag readiness light stays on after the vehicle is started or comes on while driving, it means the airbag system might not be working properly. The airbags in the vehicle might not inﬂate in a crash, or they could even inﬂate without a crash. To help avoid injury, have the vehicle serviced right away. If there is a problem with the airbag system, an airbag Driver Information Center (DIC) message can also come on. See DIC Warnings and Messages on page 3-46 for more information. 3-32 United States Canada When the vehicle is started, the passenger airbag status indicator will light ON and OFF, or the symbol for on and off, for several seconds as a system check. If you are using remote start to start the vehicle from a distance, if equipped, you may not see the system check. Then, after several more seconds, the status indicator will light either ON or OFF, or either the on or off symbol to let you know the status of the right front passenger frontal and seat-mounted side impact airbags. If the word ON or the on symbol is lit on the passenger airbag status indicator, it means that the right front passenger frontal airbag and seat-mounted side impact airbag are enabled (may inﬂate). If the word OFF or the off symbol is lit on the passenger airbag status indicator, it means that the passenger sensing system has turned off the right front passenger frontal and seat-mounted side impact airbag. If, after several seconds, both status indicator lights remain on, or if there are no lights at all, there may be a problem with the lights or the passenger sensing system. See your dealer/retailer for service. { CAUTION: If the airbag readiness light ever comes on and stays on, it means that something may be wrong with the airbag system. To help avoid injury to yourself or others, have the vehicle serviced right away. See Airbag Readiness Light on page 3-31 for more information, including important safety information. Charging System Light This light comes on brieﬂy when the ignition key is turned to START, but the engine is not running, as a check to show it is working. If it does not, have the vehicle serviced by your dealer/retailer. The light should go out once the engine starts. If it stays on, or comes on while driving, there could be a problem with the charging system. A charging system message in the Driver Information Center (DIC) can also appear. See DIC Warnings and Messages on page 3-46 for more information. This light could indicate that there are problems with a generator drive belt, or that there is an electrical problem. Have it checked right away. If the vehicle must be driven a short distance with the light on, turn off accessories, such as the radio and air conditioner. 3-33 Brake System Warning Light The vehicle’s hydraulic brake system is divided into two parts. If one part is not working, the other part can still work and stop the vehicle. For good braking both parts need to be working. If the warning light comes on, there is a brake problem. Have the brake system inspected right away. The Driver Information Center (DIC) may display a BRAKE FLUID message. See DIC Warnings and Messages on page 3-46 for more information. If the light comes on while driving, pull off the road and carefully stop. The brake pedal may be harder to push or the pedal may go closer to the ﬂoor. It may take longer to stop. Try turning off and restarting the vehicle one or two times, if the light is still on, have the vehicle towed for service. See Towing Your Vehicle on page 4-26. { CAUTION: The brake system might not be working properly if the brake system warning light is on. Driving with the brake system warning light on can lead to a crash. If the light is still on after the vehicle has been pulled off the road and carefully stopped, have the vehicle towed for service. United States Canada This light comes on brieﬂy when the ignition key is turned to ON/RUN. If it does not come on then, have it ﬁxed so it will be ready to warn if there is a problem. When the ignition is on, the brake system warning light also comes on when the parking brake is set. The light stays on if the parking brake does not fully release. If it stays on after the parking brake is fully released, it means there is a brake problem. 3-34 Antilock Brake System (ABS) Warning Light For vehicles with a Driver Information Center (DIC), see DIC Warnings and Messages on page 3-46 for all brake related DIC messages. For vehicles with the Antilock Brake System (ABS), this light comes on brieﬂy when the engine is started. Electronic Stability Control (ESC)/ Traction Control System (TCS) Indicator/Warning Light If it does not, have the vehicle serviced by your dealer/retailer. If the system is working normally the indicator light then goes off. If the ABS light stays on, turn the ignition off. If the light comes on while driving, stop as soon as it is safely possible and turn the ignition off. Then start the engine again to reset the system. If the ABS light stays on, or comes on again while driving, the vehicle needs service. If the regular brake system warning light is not on, the vehicle still has brakes, but not antilock brakes. If the regular brake system warning light is also on, the vehicle does not have antilock brakes and there is a problem with the regular brakes. See Brake System Warning Light on page 3-34. For vehicles with the Electronic Stability Control (ESC) system or the Traction Control System (TCS), the indicator/ warning light comes on brieﬂy when the engine is started. If it does not, have the vehicle serviced by the dealer/retailer. If the system is working normally the indicator light goes off. If this light is on while certain DIC messages display, this indicates that the ESC and TCS are not working or are disabled. 3-35 If this light is on and not ﬂashing, the TCS and potentially the ESC system have been disabled. Check the DIC messaging to determine which feature(s) is no longer functioning and whether it is because of the driver turning off the feature(s), or because the system is not working properly and the vehicle requires service. If the TCS is disabled, wheel spin is not limited. If the ESC system is disabled, the system does not aid in maintaining directional control of the vehicle. If the indicator/warning light is on and ﬂashing, the TCS or the ESC system is actively working. Check the DIC messaging for details to determine which system is working. If the LOW TRACTION message appears, the system is limiting wheel spin. If the ESC ACTIVE message appears, the system is aiding in maintaining directional control of the vehicle. See Electronic Stability Control (ESC) on page 4-6 and Traction Control System (TCS) on page 4-8 for more information. See DIC Warnings and Messages on page 3-46 for more information on the messages associated with this light. Engine Coolant Temperature Warning Light This light comes on brieﬂy while starting the vehicle. If it does not, have the vehicle serviced by the dealer/retailer. If the system is working normally the indicator light goes off. Notice: Driving with the engine coolant temperature warning light on could cause the vehicle to overheat. See Engine Overheating on page 5-34. The vehicle’s engine could be damaged, and it might not be covered by the vehicle warranty. Never drive with the engine coolant temperature warning light on. The engine coolant temperature warning light comes on when the engine has overheated. If this happens pull over and turn off the engine as soon as possible. See Engine Overheating on page 5-34 for more information. 3-36 Engine Coolant Temperature Gage Tire Pressure Light For vehicles with a tire pressure monitoring system, this light comes on brieﬂy when the engine is started. United States Canada This gage shows the engine coolant temperature. If the pointer moves towards the H (United States) or to the shaded thermostat symbol area (Canada), the engine is too hot. A temperature indicator light turns on and a chime sounds. The vehicle is operated under normal driving conditions and the temperature indicator light comes on, pull off the road, stop the vehicle, and turn off the engine as soon as possible. It provides information about tire pressures and the Tire Pressure Monitoring System. When the Light is On Steady This indicates that one or more of the tires is signiﬁcantly underinﬂated. A tire pressure message in the Driver Information Center (DIC), can accompany the light. See DIC Warnings and Messages on page 3-46 for more information. Stop and check the tires as soon as it is safe to do so. If a tire is underinﬂated, inﬂate to the proper pressure. See Tires on page 5-51 for more information. 3-37 When the Light Flashes First and Then is On Steady This indicates that there could be a problem with the Tire Pressure Monitor System. The light ﬂashes for about a minute and stays on steady for the remainder of the ignition cycle. This sequence repeats with every ignition cycle. See Tire Pressure Monitor System on page 5-61 for more information. Malfunction Indicator Lamp Check Engine Light A computer system called OBD II (On-Board Diagnostics-Second Generation) monitors operation of the fuel, ignition, and emission control systems. It ensures that emissions are at acceptable levels for the life of the vehicle, helping to produce a cleaner environment. This light should come on when the ignition is on, but the engine is not running, as a check to show it is working. If it does not, have the vehicle serviced by your dealer/retailer. If the check engine light comes on and stays on, while the engine is running, this indicates that there is an OBD II problem and service is required. Malfunctions often are indicated by the system before any problem is apparent. Being aware of the light can prevent more serious damage to the vehicle. This system assists the service technician in correctly diagnosing any malfunction. Notice: If the vehicle is continually driven with this light on, after a while, the emission controls might not work as well, the vehicle’s fuel economy might not be as good, and the engine might not run as smoothly. This could lead to costly repairs that might not be covered by the vehicle warranty. Notice: Modiﬁcations made to the engine, transmission, exhaust, intake, or fuel system of the vehicle or the replacement of the original tires with other than those of the same Tire Performance Criteria (TPC) can affect the vehicle’s emission controls and can cause this light to come on. Modiﬁcations to these systems could lead to costly repairs not covered by the vehicle warranty. This could also result in a failure to pass a required Emission Inspection/Maintenance test. See Accessories and Modiﬁcations on page 5-3. 3-38 This light comes on during a malfunction in one of two ways: Light Flashing: A misﬁre condition has been detected. A misﬁre increases vehicle emissions and could damage the emission control system on the vehicle. Diagnosis and service might be required. To prevent more serious damage to the vehicle: (cid:129) Reduce vehicle speed. (cid:129) Avoid hard accelerations. (cid:129) Avoid steep uphill grades. If towing a trailer, reduce the amount of cargo being hauled as soon as it is possible. If the light continues to ﬂash, when it is safe to do so, stop the vehicle. Find a safe place to park the vehicle. Turn the key off, wait at least 10 seconds, and restart the engine. If the light is still ﬂashing, follow the previous steps and see your dealer/retailer for service as soon as possible. Light On Steady: An emission control system malfunction has been detected on the vehicle. Diagnosis and service might be required. An emission system malfunction might be corrected by doing the following: (cid:129) Make sure the fuel cap is fully installed. See Filling the Tank on page 5-10. The diagnostic system can determine if the fuel cap has been left off or improperly installed. A loose or missing fuel cap allows fuel to evaporate into the atmosphere. A few driving trips with the cap properly installed should turn the light off. If the vehicle has been driven through a deep puddle of water, the vehicle’s electrical system might be wet. The condition is usually corrected when the electrical system dries out. A few driving trips should turn the light off. 3-39 (cid:129) (cid:129) (cid:129) Make sure to fuel the vehicle with quality fuel. Poor fuel quality causes the engine not to run as efficiently as designed and can cause: stalling after start-up, stalling when the vehicle is changed into gear, misﬁring, hesitation on acceleration, or stumbling on acceleration. These conditions might go away once the engine is warmed up. If one or more of these conditions occurs, change the fuel brand used. It will require at least one full tank of the proper fuel to turn the light off. See Gasoline Octane on page 5-6. If none of the above have made the light turn off, your dealer/retailer can check the vehicle. The dealer/retailer has the proper test equipment and diagnostic tools to ﬁx any mechanical or electrical problems that might have developed. Emissions Inspection and Maintenance Programs Some state/provincial and local governments have or might begin programs to inspect the emission control equipment on the vehicle. Failure to pass this inspection could prevent getting a vehicle registration. Here are some things to know to help the vehicle pass an inspection: The vehicle will not pass this inspection if the check engine light is on with the engine running, or if the key is in ON/RUN and the light is not on. The vehicle will not pass this inspection if the OBD II (on-board diagnostic) system determines that critical emission control systems have not been completely diagnosed by the system. The vehicle would be considered not ready for inspection. This can happen if the battery has recently been replaced or if the battery has run down. The diagnostic system is designed to evaluate critical emission control systems during normal driving. This can take several days of routine driving. If this has been done and the vehicle still does not pass the inspection for lack of OBD II system readiness, your dealer/retailer can prepare the vehicle for inspection. 3-40 (cid:129) (cid:129) Oil Pressure Light { CAUTION: Do not keep driving if the oil pressure is low. The engine can become so hot that it catches ﬁre. Someone could be burned. Check the oil as soon as possible and have the vehicle serviced. Notice: Lack of proper engine oil maintenance can damage the engine. The repairs would not be covered by the vehicle warranty. Always follow the maintenance schedule in this manual for changing engine oil. This light comes on brieﬂy while starting the engine. If it does not, have the vehicle serviced by your dealer/ retailer. If the system is working normally the indicator light then goes off. If the light comes on and stays on, it means that oil is not ﬂowing through the engine properly. The vehicle could be low on oil and it might have some other system problem. Security Light For information regarding this light and the vehicle’s security system, see Content Theft-Deterrent on page 2-18. 3-41 Cruise Control Light Fuel Gage The cruise control light comes on whenever the cruise control is set. The light goes out when the cruise control is turned off. See Cruise Control on page 3-10 for more information. Highbeam On Light This light comes on when the high-beam headlamps are in use. United States Canada When the ignition is on, the fuel gage shows much fuel is left in the fuel tank. When the indicator nears empty, a message in the Driver Information Center (DIC) displays. The vehicle still has a little fuel left, but the vehicle should be fueled soon. An arrow on the fuel gage indicates the side of the vehicle the fuel door is on. See Headlamp High/Low-Beam Changer on page 3-8 for more information. 3-42 Here are four things that some owners ask about. These are normal and do not indicate a problem with the fuel gage: (cid:129) At the service station, the gas pump shuts off before the gage reads full. It takes a little more or less fuel to ﬁll up than the gage indicated. For example, the gage may have indicated the fuel tank was half full, but it actually took a little more or less than half the fuel tank’s capacity to ﬁll it. The indicator moves a little while turning a corner or speeding up. The gage goes back to empty when the ignition is turned off. Driver Information Center (DIC) Your vehicle has a Driver Information Center (DIC). The DIC display gives you the status of many of your vehicle’s systems. The DIC is also used to display driver personalization menu modes and warning/status messages. All messages will appear in the DIC display, located at the bottom of the instrument panel cluster. The DIC buttons are located on the left side of the steering wheel. INFO (Information): Press this button to scroll through the vehicle information mode displays. r (Reset): Press this button to reset some vehicle information mode displays, select a personalization menu mode setting, or acknowledge a warning message. Press and hold the information and reset buttons at the same time for one second, then release the buttons to enter the personalization menu. See DIC Vehicle Personalization on page 3-50 for more information. 3-43 (cid:129) (cid:129) (cid:129) DIC Operation and Displays The DIC comes on when the ignition is on. The DIC has different modes which can be accessed by pressing the DIC buttons. The button functions are detailed in the following. Information Modes INFO (Information): Press this button to scroll through the following vehicle information modes: Outside Air Temperature The outside air temperature will be displayed at the same time as the Odometer and the Trip Odometer. The temperature outside of the vehicle will be displayed in either degrees Fahrenheit (°F) or degrees Celsius (°C). The outside air temperature appears on the left side of the DIC display and the odometer, or trip odometer, appears on the right side of the display. Odometer Press the information button until the outside air temperature and the odometer displays. This mode shows the total distance the vehicle has been driven in either miles (mi) or kilometers (km). To change the DIC display to English or metric units, see “UNITS” under DIC Vehicle Personalization on page 3-50. 3-44 Trip Odometer Press the information button until the outside air temperature along with A or B displays. These modes show the current distance traveled since the last reset for each trip odometer in either miles (mi) or kilometers (km). Both odometers can be used at the same time. To reset the trip odometer to zero, press and hold the reset button for a few seconds while the desired trip odometer is displayed. FUEL RANGE Press the information button until FUEL RANGE displays. This mode shows the remaining distance you can drive without refueling in either miles (mi) or kilometers (km). It is based on fuel economy and the fuel remaining in the tank. When the fuel level is low, FUEL RANGE LOW displays. The fuel economy data used to determine fuel range is an average of recent driving conditions. As your driving conditions change, this data is gradually updated. The FUEL RANGE mode cannot be reset. MPG (L/100 KM) AVG (Average) Press the information button until MPG (L/100 KM) AVG displays. This mode shows how many miles per gallon (mpg) or liters per 100 kilometers (L/100 km) your vehicle is getting based on current and past driving conditions. To reset the average fuel economy, press and hold the reset button while MPG (L/100 KM) AVG is displayed. Average fuel economy is then calculated starting from that point. If the average fuel economy is not reset, it is continually updated each time you drive. MPG (L/100 KM) INST (Instantaneous) Press the information button until MPG (L/100 KM) INST displays. This mode shows the current fuel economy at a particular moment and changes frequently as driving conditions change. This mode shows the instantaneous fuel economy in miles per gallon (mpg) or liters per 100 kilometers (L/100 km). Unlike average fuel economy, this screen cannot be reset. AV (Average) SPEED Press the information button until AV SPEED displays. This mode shows the vehicle’s average speed in miles per hour (mph) or kilometers per hour (km/h). To reset the average vehicle speed, press and hold the reset button while AV SPEED is displayed. OIL LIFE Press the information button until OIL LIFE displays. The engine oil life system shows an estimate of the oil’s remaining useful life. It shows 100% when the system is reset after an oil change. It alerts you to change the oil on a schedule consistent with your driving conditions. In addition to the engine oil life system monitoring the oil life, additional maintenance is recommended in the Maintenance Schedule in this manual. See Engine Oil on page 5-21 and Scheduled Maintenance on page 6-4. Always reset the engine oil life system after an oil change. See “How to Reset the Engine Oil Life System” under Engine Oil Life System on page 5-24. Tire Pressure On vehicles with the Tire Pressure Monitor System (TPMS), the pressure for each tire can be viewed in the DIC. The tire pressure is shown in either pounds per square inch (psi) or kilopascals (kPa). Press the information button until LF ## PSI (kPa) ## RF displays for the front tires. Press the information button again until LR ## PSI (kPa) ## RR displays for the rear tires. If a low tire pressure condition is detected by the system while driving, a message advising you to check the tire pressure appears in the display. See Inﬂation - Tire Pressure on page 5-59 and DIC Warnings and Messages on page 3-46 for more information. 3-45 DIC Warnings and Messages These messages appear if there is a problem detected in one of your vehicle’s systems. A message clears when the vehicle’s condition is no longer present. To acknowledge a message and clear it from the display, press and hold any of the DIC buttons. If the condition is still present, the warning message comes back on the next time the vehicle is turned off and back on. With most messages, a warning chime sounds when the message displays. Your vehicle may have other warning messages. AUTO (Automatic) LIGHTS OFF This message displays if the automatic headlamp system is disabled with the headlamp switch. See Automatic Headlamp System on page 3-15 for more information. AUTO (Automatic) LIGHTS ON This message displays if the automatic headlamp system is enabled with the headlamp switch. See Automatic Headlamp System on page 3-15 for more information. BRAKE FLUID This message displays, while the ignition is on, when the brake ﬂuid level is low. The brake system warning light on the instrument panel cluster also comes on. See Brake System Warning Light on page 3-34 for more information. Have the brake system serviced by your dealer/retailer as soon as possible. CHANGE OIL SOON This message displays when the life of the engine oil has expired and it should be changed. When this message is acknowledged and cleared from the display, the engine oil life system must still be reset separately. See Engine Oil Life System on page 5-24, Engine Oil on page 5-21, and Scheduled Maintenance on page 6-4 for more information. CHECK GAS CAP This message displays if the fuel cap has not been fully tightened. Recheck the fuel cap to make sure that it is on properly. A few driving trips with the cap properly installed should turn the message off. 3-46 CHECK TIRE PRESS (Pressure) On vehicles with the Tire Pressure Monitor System (TPMS), this message displays when the pressure in one or more of the vehicle’s tires needs to be checked. If a tire pressure message appears on the DIC, stop as soon as you can. Have the tire pressures checked and set to those shown on the Tire Loading Information label. See Tires on page 5-51, Loading the Vehicle on page 4-20, and Inﬂation - Tire Pressure on page 5-59. The DIC also shows the tire pressure values. See DIC Operation and Displays on page 3-44. If the tire pressure is low, the low tire pressure warning light comes on. See Tire Pressure Light on page 3-37. CRUISE ENGAGED This message displays when the cruise control system is active. See Cruise Control on page 3-10 for more information. DOOR AJAR This message displays if one or more of the vehicle’s doors are not closed properly. Make sure that the door(s) are closed completely. ENGINE DISABLED This message displays if the starting of the engine is disabled. Have your vehicle serviced by your dealer/retailer immediately. ENG (Engine) PWR (Power) REDUCED This message displays when the vehicle’s engine power is reduced. Reduced engine power can affect the vehicle’s ability to accelerate. If this message is on, but there is no reduction in performance, proceed to your destination. The performance may be reduced the next time the vehicle is driven. The vehicle may be driven at a reduced speed while this message is on, but acceleration and speed may be reduced. Anytime this message stays on, the vehicle should be taken to your dealer/retailer for service as soon as possible. ESC (Electronic Stability Control) ACTIVE If your vehicle has Electronic Stability Control (ESC), this message displays and the ESC/TCS light on the instrument panel cluster ﬂashes when ESC is assisting you with directional control of the vehicle. You may feel or hear the system working and see this message displayed in the DIC. Slippery road conditions may exist when this message is displayed, so adjust your driving accordingly. This message may stay on for a few seconds after ESC stops assisting you with directional control of the vehicle. This is normal when the system is operating. See Electronic Stability Control (ESC) on page 4-6 and Electronic Stability Control (ESC)/Traction Control System (TCS) Indicator/Warning Light on page 3-35 for more information. 3-47 ESC (Electronic Stability Control) OFF If your vehicle has Electronic Stability Control (ESC), this message displays and the ESC/TCS light on the instrument panel cluster comes on solid when ESC is turned off. Adjust your driving accordingly. See Electronic Stability Control (ESC) on page 4-6 and Electronic Stability Control (ESC)/Traction Control System (TCS) Indicator/Warning Light on page 3-35 for more information. ICE POSSIBLE This message displays when the outside air temperature is cold enough to create icy road conditions. Adjust your driving accordingly. KEY FOB BATT (Battery) LOW This message displays if the Remote Keyless Entry (RKE) transmitter battery is low. Replace the battery in the transmitter. See “Battery Replacement” under Remote Keyless Entry (RKE) System Operation on page 2-5. LOW FUEL This message displays when your vehicle is low on fuel. Reﬁll the fuel tank as soon as possible. See Fuel Gage on page 3-42, Fuel on page 5-5, and Filling the Tank on page 5-10 for more information. 3-48 LOW TRACTION If your vehicle has the Traction Control System (TCS), this message displays and the ESC/TCS light on the instrument panel cluster ﬂashes when the system is actively limiting wheel spin. Slippery road conditions may exist if this message is displayed, so adjust your driving accordingly. This message stays on for a few seconds after the system stops limiting wheel spin. See Traction Control System (TCS) on page 4-8 and Electronic Stability Control (ESC)/Traction Control System (TCS) Indicator/Warning Light on page 3-35 for more information. LOW WASHER FLUID This message displays when the vehicle’s windshield washer ﬂuid is low. Fill the windshield washer ﬂuid reservoir to the proper level as soon as possible. See Windshield Washer Fluid on page 5-38. POWER STEERING On some vehicles, this message displays if a problem has been detected with the electric power steering. Have your vehicle serviced by your dealer/retailer immediately. PUSH PARK PEDAL This message displays if the parking brake is left engaged. See Parking Brake on page 2-32 for more information. SERVICE AIR BAG This message displays when there is a problem with the airbag system. Have your vehicle serviced by your dealer/retailer immediately. SERVICE ESC (ELECTRONIC STABILITY CONTROL) If your vehicle has Electronic Stability Control (ESC), this message displays and a chime sounds if there has been a problem detected with ESC. The ESC/TCS light also appears on the instrument panel cluster. This light stays on solid as long as the detected problem remains present. When this message displays, the system is not working. Adjust your driving accordingly. See Electronic Stability Control (ESC) on page 4-6 and Electronic Stability Control (ESC)/Traction Control System (TCS) Indicator/Warning Light on page 3-35 for more information. If this message turns on while you are driving, pull off the road as soon as possible and stop carefully. Try resetting the system by turning the ignition off and then back on. If this message still stays on or turns back on again while you are driving, your vehicle needs service. Have the ESC inspected by your dealer/retailer as soon as possible. SERVICE TRACTION If your vehicle has the Traction Control System (TCS), this message displays and a chime sounds when the system is not functioning properly. The ESC/TCS light also appears on the instrument panel cluster. This light stays on solid as long as the detected problem remains present. When this message displays, the system is not working. Adjust your driving accordingly. See Traction Control System (TCS) on page 4-8 and Electronic Stability Control (ESC)/Traction Control System (TCS) Indicator/Warning Light on page 3-35 for more information. Have the system serviced by your dealer/ retailer as soon as possible. SVC (Service) TIRE MONITOR On vehicles with the Tire Pressure Monitor System (TPMS), this message displays if a part on the TPMS is not working properly. The tire pressure light also ﬂashes and then remains on during the same ignition cycle. See Tire Pressure Light on page 3-37. Several conditions may cause this message to appear. See Tire Pressure Monitor Operation on page 5-62 for more information. If the warning comes on and stays on, there may be a problem with the TPMS. See your dealer/retailer. 3-49 To change feature settings, use the following procedure: Entering Personalization Menu 1. Turn the ignition on while the vehicle is stopped. To avoid excessive drain on the battery, it is recommended that the headlamps are turned off. 2. Press and hold the information and reset buttons at the same time for one second, then release to enter the personalization menu. If the vehicle speed is greater than 2 mph (3 km/h), only the UNITS menu will be accessible. 3. Press the information button to scroll through the available personalization menu modes. Press the reset button to scroll through the available settings for each mode. If you do not make a selection within ten seconds, the display will go back to the previous information displayed. TRACTION OFF If your vehicle has the Traction Control System (TCS), this message displays and the ESC/TCS light on the instrument panel cluster comes on solid when the system is turned off. Adjust your driving accordingly. See Traction Control System (TCS) on page 4-8 and Electronic Stability Control (ESC)/Traction Control System (TCS) Indicator/Warning Light on page 3-35 for more information. TRUNK AJAR This message displays when the trunk is not closed completely. Make sure that the trunk is closed completely. See Trunk on page 2-12 for more information. DIC Vehicle Personalization Your vehicle has personalization capabilities that allow you to program certain features to a preferred setting. All of the features listed may not be available on your vehicle. Only the features available will be displayed on the DIC. The default settings for the features were set when your vehicle left the factory, but may have been changed from their default state since that time. 3-50 Personalization Menu Modes OIL LIFE RESET When this feature is displayed, you can reset the engine oil life system. To reset the system, see Engine Oil Life System on page 5-24. See “OIL LIFE” under DIC Operation and Displays on page 3-44 for more information. UNITS This feature allows you to select the units of measurement in which the DIC will display the vehicle information. When UNITS appears on the display, press and hold the reset button for at least one second to scroll through the available settings: ENGLISH (default in United States): All information will be displayed in English units. METRIC (default in Canada): All information will be displayed in metric units. To select a setting and move on to the next feature, press the information button while the desired setting is displayed on the DIC. REMOTE START If your vehicle has remote start, this feature allows remote start to be turned off or on. Remote start allows you to start the engine from outside of the vehicle using your Remote Keyless Entry (RKE) transmitter. When REMOTE START appears on the display, press and hold the reset button for at least one second to scroll through the available settings: OFF: The remote start feature will be disabled. ON (default): The remote start feature will be enabled. See Remote Vehicle Start on page 2-7 for more information. To select a setting and move on to the next feature, press the information button while the desired setting is displayed on the DIC. 3-51 LOCK HORN This feature, which allows the vehicle’s horn to chirp every time the lock button on the Remote Keyless Entry (RKE) transmitter is pressed, can be enabled or disabled. When LOCK HORN appears on the display, press and hold the reset button for at least one second to scroll through the available settings: UNLOCK HORN This feature, which allows the vehicle’s horn to chirp on the ﬁrst press of the unlock button on the Remote Keyless Entry (RKE) transmitter, can be enabled or disabled. When UNLOCK HORN appears on the display, press and hold the reset button for at least one second to scroll through the available settings: OFF (default): The horn will not chirp on the ﬁrst press of the lock button on the RKE transmitter. The horn will still chirp on the second press. ON: The horn will chirp on the ﬁrst press of the lock button on the RKE transmitter. See Remote Keyless Entry (RKE) System Operation on page 2-5 for more information. To select a setting and move on to the next feature, press the information button while the desired setting is displayed on the DIC. OFF (default): The horn will not chirp when the unlock button on the RKE transmitter is pressed. ON: The horn will chirp on the ﬁrst press of the unlock button on the RKE transmitter. See Remote Keyless Entry (RKE) System Operation on page 2-5 for more information. To select a setting and move on to the next feature, press the information button while the desired setting is displayed on the DIC. 3-52 LIGHT FLASH This feature, which allows the vehicle’s exterior hazard/ turn signal lighting to ﬂash every time the lock, unlock, or trunk release buttons on the Remote Keyless Entry (RKE) transmitter are pressed, can be enabled or disabled. When LIGHT FLASH appears on the display, press and hold the reset button for at least one second to scroll through the available settings: OFF: The exterior hazard/turn signal lighting will not ﬂash when the lock, unlock, or trunk release buttons on the RKE transmitter are pressed. ON (default): The exterior hazard/turn signal lighting will ﬂash when the lock, unlock, or trunk release buttons on the RKE transmitter are pressed. See Remote Keyless Entry (RKE) System Operation on page 2-5 for more information. To select a setting and move on to the next feature, press the information button while the desired setting is displayed on the DIC. DELAY LOCK This feature, which delays the actual locking of the vehicle, can be enabled or disabled. When DELAY LOCK appears on the display, press and hold the reset button for at least one second to scroll through the available settings: ON (default): The doors will not lock until ﬁve seconds after the last door is closed. You can temporarily override delayed locking by pressing the power lock switch or the lock button on the Remote Keyless Entry (RKE) transmitter a second time. OFF: The doors will lock immediately when pressing the power lock switch or the lock button on the RKE transmitter. See Power Door Locks on page 2-10, Delayed Locking on page 2-11, and Remote Keyless Entry (RKE) System Operation on page 2-5 for more information. To select a setting and move on to the next feature, press the information button while the desired setting is displayed on the DIC. 3-53 AUTO UNLK (Unlock) This feature, which allows the vehicle to automatically unlock certain doors, can be enabled or disabled. When AUTO UNLK appears on the display, press and hold the reset button for at least one second to scroll through the available settings: ALL (default): All of the doors will automatically unlock. DRIVER: The driver’s door will automatically unlock. NONE: None of the doors will automatically unlock. You will need to manually unlock the doors. See Programmable Automatic Door Locks on page 2-11 for more information. To select a setting and move on to the next feature, press the information button while the desired setting is displayed on the DIC. UNLK (Unlock) This screen displays only if DRIVER or ALL is selected for the AUTO UNLK feature. This feature determines when the automatic door unlocking will occur. When UNLK appears on the display, press and hold the reset button for at least one second to scroll through the available settings: KEY OFF: The door(s) will unlock when the key is turned off. SHIFT TO P (Park) (default): The door(s) will unlock when the vehicle is shifted into P (Park). See Programmable Automatic Door Locks on page 2-11 for more information. To select a setting and move on to the next feature, press the information button while the desired setting is displayed on the DIC. 3-54 EXT (Exterior) LIGHTS This feature, which allows the vehicle’s exterior perimeter lighting to turn on each time the unlock button on the Remote Keyless Entry (RKE) transmitter is pressed, can be enabled or disabled. When EXT LIGHTS appears on the display, press and hold the reset button for at least one second to scroll through the available settings: OFF: The exterior perimeter lighting will not turn on when the unlock button on the RKE transmitter is pressed. ON (default): The exterior perimeter lighting will turn on when the unlock button on the RKE transmitter is pressed. See Remote Keyless Entry (RKE) System Operation on page 2-5 for more information. To select a setting and move on to the next feature, press the information button while the desired setting is displayed on the DIC. LANGUAGE This feature allows you to select the language in which the DIC will display. When LANGUAGE appears on the display, press and hold the reset button for at least one second to scroll through the available settings: ENGLISH (default): All messages will appear in English. FRENCH: All messages will appear in French. SPANISH: All messages will appear in Spanish. GERMAN: All messages will appear in German. To select a setting and exit out of the personalization menu mode, press the information button while the desired setting is displayed on the DIC. Exiting Personalization Menu The personalization menu will be exited when any of the following conditions occur: (cid:129) A ten second time period has elapsed. The ignition is turned off. The end of the personalization menu list is reached. 3-55 (cid:129) (cid:129) Notice: Contact your dealer/retailer before adding any equipment. Adding audio or communication equipment could interfere with the operation of the vehicle’s engine, radio, or other systems, and could damage them. Follow federal rules covering mobile radio and telephone equipment. Notice: The chime signals related to safety belts, parking brake, and other functions of your vehicle operate through the radio/entertainment system. If that equipment is replaced or additional equipment is added to your vehicle, the chimes may not work. Make sure that replacement or additional equipment is compatible with your vehicle before installing it. See Accessories and Modiﬁcations on page 5-3. The vehicle has Retained Accessory Power (RAP). With RAP, the audio system can be played even after the ignition is turned off. See Retained Accessory Power (RAP) on page 2-23 for more information. Audio System(s) Determine which radio the vehicle has and read the following pages to become familiar with its features. { CAUTION: Taking your eyes off the road for extended periods could cause a crash resulting in injury or death to you or others. Do not give extended attention to entertainment tasks while driving. This system provides access to many audio and non audio listings. To minimize taking your eyes off the road while driving, do the following while the vehicle is parked: (cid:129) Become familiar with the operation and controls of the audio system. (cid:129) Set up the tone, speaker adjustments, and preset radio stations. For more information, see Defensive Driving on page 4-2. 3-56

Boost Classifieds - Car Advice, Reviews, Events & Classifieds

2009 Chevrolet Malibu Owners Manual