2006 Cadillac Escalade Owners Manual

Download PDF Manual
your vehicle. The dealer can give you the best advice for that particular area. Automatic Transmission Operation Your vehicle is equipped with an automatic transmission and features an electronic shift position indicator located within the instrument panel cluster. There are several different positions for your shift lever. PARK (P): This position locks your drive wheels. It is the best position to use when you start your engine because your vehicle cannot move easily. {CAUTION: It is dangerous to get out of your vehicle if the shift lever is not fully in PARK (P) with the parking brake ﬁrmly set. Your vehicle can roll. Do not leave your vehicle when the engine is running unless you have to. If you have left the engine running, the vehicle can move suddenly. You or others could be injured. To be sure your vehicle will not move, even when you are on fairly level ground, always set your parking brake and move the shift lever to PARK (P). See Shifting Into Park (P) on page 2-24. If you are pulling a trailer, see Towing a Trailer on page 4-53. To rock your vehicle back and forth to get out of snow, ice or sand without damaging your transmission, see If Your Vehicle is Stuck in Sand, Mud, Ice or Snow on page 4-44. NEUTRAL (N): In this position, your engine does not connect with the wheels. To restart when you are already moving, use NEUTRAL (N) only. {CAUTION: Shifting into a drive gear while your engine is running at high speed is dangerous. Unless your foot is ﬁrmly on the brake pedal, your vehicle could move very rapidly. You could lose control and hit people or objects. Do not shift into a drive gear while your engine is running at high speed. REVERSE (R): Use this gear to back up. Notice: Shifting to REVERSE (R) while your vehicle is moving forward could damage the transmission. The repairs would not be covered by your warranty. Shift to REVERSE (R) only after your vehicle is stopped. Notice: Shifting out of PARK (P) or NEUTRAL (N) with the engine running at high speed may damage the transmission. The repairs would not be covered by your warranty. Be sure the engine is not running at high speed when shifting your vehicle. 2-21 DRIVE (D): This position is for normal driving. If you need more power for passing, and you are: (cid:127) Going less than about 35 mph (55 km/h), push your accelerator pedal about halfway down. (cid:127) Going about 35 mph (55 km/h) or more, push the accelerator all the way down. You will shift down to the next gear and have more power. DRIVE (D) can be used when towing a trailer, carrying a heavy load, driving on steep hills or for off-road driving. You may want to shift the transmission to THIRD (3) or, if necessary, a lower gear selection if the transmission shifts too often. THIRD (3): This position is also used for normal driving, however it offers more power and lower fuel economy than DRIVE (D). SECOND (2): This position gives you more power but lower fuel economy. You can use SECOND (2) on hills. It can help control your speed as you go down steep mountain roads, but then you would also want to use your brakes off and on. If you manually select SECOND (2), the transmission will drive in second gear. You may use this feature for reducing the speed of the rear wheels when you are trying to start your vehicle from a stop on slippery road surfaces. Once the vehicle is moving, shift into DRIVE (D). FIRST (1): This position gives you even more power, but lower fuel economy than SECOND (2). You can use it on very steep hills, or in deep snow or mud. If the shift lever is put in FIRST (1) while the vehicle is moving forward, the vehicle will not shift into ﬁrst gear until the vehicle is going slowly enough. Notice: Spinning the tires or holding the vehicle in one place on a hill using only the accelerator pedal may damage the transmission. If you are stuck, do not spin the tires. When stopping on a hill, use the brakes to hold the vehicle in place. On cold days, approximately 32°F (0°C) or colder, your transmission is designed to shift differently until the engine reaches normal operating temperature. This is intended to improve heater performance. 2-22 Tow/Haul Mode Your vehicle is equipped with a tow/haul mode. The button for this feature is located on the end of the column shift lever. You can use this feature to assist when towing or hauling a heavy load. See “Tow/Haul Mode” under Towing a Trailer on page 4-53 for more information. The tow/haul mode also interacts with the Road Sensing Suspension (RSS) feature to enhance the ride when trailering or with a loaded vehicle. See Road Sensing Suspension on page 4-9. Parking Brake To set the parking brake, hold the regular brake pedal down with your right foot. Push down the parking brake pedal with your left foot. A chime will activate and the warning light will ﬂash when the parking brake is applied and the vehicle is moving at least 3 mph (5 km/h) for at least three seconds. To release the parking brake, hold the regular brake pedal down. Pull the bottom edge of the lever, located above the parking brake pedal, with the parking brake symbol, to release the parking brake. If the ignition is on when the parking brake is released, the brake system warning light will go off. Notice: Driving with the parking brake on can overheat the brake system and cause premature wear or damage to brake system parts. Verify that the parking brake is fully released and the brake warning light is off before driving. If you are towing a trailer and are parking on any hill, see Towing a Trailer on page 4-53. 2-23 Shifting Into Park (P) {CAUTION: It can be dangerous to get out of your vehicle if the shift lever is not fully in PARK (P) with the parking brake ﬁrmly set. Your vehicle can roll. If you have left the engine running, the vehicle can move suddenly. You or others could be injured. To be sure your vehicle will not move, even when you are on fairly level ground, use the steps that follow. If you are pulling a trailer, see Towing a Trailer on page 4-53. 1. Hold the brake pedal down with your right foot and set the parking brake with your left foot. 2. Move the shift lever into PARK (P) by pulling the shift lever toward you and moving it up as far as it will go. 3. Turn the ignition key to LOCK. 4. Remove the key and take it with you. If you can leave your vehicle with the ignition key in your hand, your vehicle is in PARK (P). 2-24 Leaving Your Vehicle With the Engine Running {CAUTION: It can be dangerous to leave your vehicle with the engine running. Your vehicle could move suddenly if the shift lever is not fully in PARK (P) with the parking brake ﬁrmly set. And, if you leave the vehicle with the engine running, it could overheat and even catch ﬁre. You or others could be injured. Do not leave your vehicle with the engine running. If you have to leave your vehicle with the engine running, be sure your vehicle is in PARK (P) and the parking brake is ﬁrmly set before you leave it. After you move the shift lever into PARK (P), hold the regular brake pedal down. Then, see if you can move the shift lever away from PARK (P) without ﬁrst pulling it toward you. If you can, it means that the shift lever was not fully locked into PARK (P). Torque Lock If you are parking on a hill and you do not shift your vehicle into PARK (P) properly, the weight of the vehicle may put too much force on the parking pawl in the transmission. You may ﬁnd it difficult to pull the shift lever out of PARK (P). This is called torque lock. To prevent torque lock, set the parking brake and then shift into PARK (P) properly before you leave the driver’s seat. To ﬁnd out how, see Shifting Into Park (P) on page 2-24. When you are ready to drive, move the shift lever out of PARK (P) before you release the parking brake. If torque lock does occur, you may need to have another vehicle push yours a little uphill to take some of the pressure from the parking pawl in the transmission, so you can pull the shift lever out of PARK (P). Shifting Out of Park (P) Your vehicle has an automatic transmission shift lock control system. You have to fully apply your regular brakes before you can shift from PARK (P) when the ignition is in RUN. See Automatic Transmission Operation on page 2-20. If you cannot shift out of PARK (P), ease pressure on the shift lever and push the shift lever all the way up into PARK (P) as you maintain brake application. Then, move the shift lever into the gear you want. If you ever hold the brake pedal down but still cannot shift out of PARK (P), try this: 1. Turn the key to ACCESSORY. There is no shift interlock in this key position. 2. Apply and hold the brake until the end of Step 4. 3. Shift the vehicle to NEUTRAL (N). 4. Start the vehicle and then shift to the drive gear you want. 5. Have the system ﬁxed as soon as possible. 2-25 Parking Over Things That Burn Engine Exhaust {CAUTION: Engine exhaust can kill. It contains the gas carbon monoxide (CO), which you cannot see or smell. It can cause unconsciousness and death. You might have exhaust coming in if: (cid:127) Your exhaust system sounds strange or different. (cid:127) Your vehicle gets rusty underneath. (cid:127) Your vehicle was damaged in a collision. (cid:127) Your vehicle was damaged when driving over high points on the road or over road debris. (cid:127) Repairs were not done correctly. (cid:127) Your vehicle or exhaust system had been modiﬁed improperly. If you ever suspect exhaust is coming into your vehicle: (cid:127) Drive it only with all the windows down to blow out any CO; and (cid:127) Have your vehicle ﬁxed immediately. {CAUTION: Things that can burn could touch hot exhaust parts under your vehicle and ignite. Do not park over papers, leaves, dry grass, or other things that can burn. 2-26 Running the Engine While Parked It is better not to park with the engine running. But if you ever have to, here are some things to know. {CAUTION: {CAUTION: Idling the engine with the climate control system off could allow dangerous exhaust into your vehicle. See the earlier caution under Engine Exhaust on page 2-26. Also, idling in a closed-in place can let deadly carbon monoxide (CO) into your vehicle even if the climate control fan is at the highest setting. One place this can happen is a garage. Exhaust — with CO — can come in easily. NEVER park in a garage with the engine running. Another closed-in place can be a blizzard. See Winter Driving on page 4-40. It can be dangerous to get out of your vehicle if the shift lever is not fully in PARK (P) with the parking brake ﬁrmly set. Your vehicle can roll. Do not leave your vehicle when the engine is running unless you have to. If you have left the engine running, the vehicle can move suddenly. You or others could be injured. To be sure your vehicle will not move, even when you are on fairly level ground, always set your parking brake and move the shift lever to PARK (P). Follow the proper steps to be sure your vehicle will not move. See Shifting Into Park (P) on page 2-24. If you are pulling a trailer, see Towing a Trailer on page 4-53. 2-27 Mirrors Automatic Dimming Rearview Mirror with OnStar® and Compass Your vehicle may have an automatic-dimming rearview mirror with a compass and the OnStar® system. There are three additional buttons for the OnStar® system. See your dealer for more information on the system and how to subscribe to OnStar®. See OnStar® System on page 2-36 for more information about the services OnStar® provides. Mirror Operation When turned on, this mirror automatically dims to the proper level to minimize glare from any headlamps behind you after dark. O (On/Off): This is the on/off button for the automatic dimming feature and compass. Press the far left button, located below the mirror face, for up to three seconds to turn the feature on and off. A light on the mirror will be lit while the feature is turned on. 2-28 Compass Operation Press the on/off button once to turn the compass on or off. There is a compass display in the window in the upper right corner of the mirror face. The compass displays a maximum of two characters. For example, “NE” is displayed for north-east. Compass Calibration Press and hold the on/off button down for nine seconds to activate the compass calibration mode. CAL will be displayed in the compass window on the mirror. The compass can be calibrated by driving the vehicle in circles at 5 mph (8 km/h) or less until the display reads a direction. Compass Variance Compass variance is the difference between earth’s magnetic north and true geographic north. The mirror is set to zone eight upon leaving the factory. It will be necessary to adjust the compass to compensate for compass variance if you live outside zone eight. Under certain circumstances, such as during a long distance cross-country trip, it will be necessary to adjust for compass variance. If not adjusted to account for compass variance, your compass could give false readings. To adjust for compass variance, do the following: 1. Find your current location and variance zone number on the map. 2. Press and hold the on/off button for six seconds. Release the button when ZONE is displayed. The number shown is the current zone number. 3. Scroll through the zone numbers that appear in the compass/temperature window on the mirror by pressing the on/off button. Once you ﬁnd your zone number, release the button. After about four seconds, the mirror will return to the compass display, and the new zone number will be set. Automatic Dimming Rearview Mirror with OnStar®, Compass and Temperature Display Your vehicle may have this feature. When on, the automatic dimming mirror dims to the proper level to minimize glare from lights behind you after dark. The mirror has a dual display in the upper right corner of the mirror face that shows the compass reading and the outside temperature. Control buttons for the OnStar® system are at the bottom of the mirror. See OnStar® System on page 2-36 for more information about the services OnStar® provides. P (On/Off): This is the on/off button. 2-29 Temperature and Compass Display Press the on/off button, located to the far left, brieﬂy to turn the compass/temperature display on or off. If the display reads CAL, the compass needs to be calibrated. For more information, see “Compass Calibration” following. To adjust between Fahrenheit and Celsius, do the following: 1. Press and hold the on/off button for approximately four seconds until either a ﬂashing F or C appears. 2. Press the button again to change the display to the desired unit of measurement. After approximately four seconds of inactivity, the new unit will be locked in and the compass/temperature display will return. If an abnormal temperature reading is displayed for an extended period of time, please see your GM dealer. Under certain circumstances, a delay in updating the temperature is normal. Automatic Dimming Mirror Operation The automatic dimming mirror function is turned on automatically each time the ignition is started. To operate the automatic dimming mirror, do the following: 1. Make sure the green indicator light, located to the left of the on/off button, is lit. If it is not, press and hold the on/off button for approximately six seconds until the green light comes on, indicating that the mirror is in automatic dimming mode. 2. Turn off the automatic dimming mirror function by pressing and holding the on/off button for approximately six seconds, until the green indicator light turns off. Compass Variance The mirror is set in zone eight upon leaving the factory. It will be necessary to adjust the compass to compensate for compass variance if the vehicle is outside of zone eight. Under certain circumstances, as during a long distance cross-country trip, it will be necessary to adjust for compass variance. Compass variance is the difference between earth’s magnetic north and true geographic north. If not adjusted to account for compass variance, the compass could give false readings. 2-30 To adjust for compass variance, do the following: 1. Find your current location and variance zone number on the following zone map. 2. Press and hold the on/off button until a Z and a zone number appears in the display. The compass is now in zone mode. 3. Keep pressing the on/off button until the desired zone number appears in the display. Release the button. After approximately four seconds of inactivity, the new zone number will be locked in and the compass/temperature display will return. 4. Calibrate the compass as described next. Compass Calibration The compass may need calibration if one of the following occurs: (cid:127) After approximately ﬁve seconds, the display does not show a compass heading, N for North, for example, there may be a strong magnetic ﬁeld interfering with the compass. Such interference may be caused by a magnetic antenna mount, magnetic note pad holder, or a similar magnetic item. The compass does not display the correct heading and the compass zone variance is set correctly. In order to calibrate, CAL must be displayed in the mirror compass windows. If CAL is not displayed, push the on/off button for approximately 12 seconds or until CAL is displayed. The compass can be calibrated by driving the vehicle in circles at 5 mph (8 km/h) or less until the display reads a direction. 2-31 (cid:127) Passenger Airbag Indicator The vehicle may be equipped with a passenger airbag indicator, on the mirror glass, just above the buttons. For more information, see Passenger Sensing System on page 1-82 and Passenger Airbag Status Indicator on page 3-36. Cleaning the Mirror When cleaning the mirror, use a paper towel or similar material dampened with glass cleaner. Do not spray glass cleaner directly on the mirror as that may cause the liquid cleaner to enter the mirror housing. Automatic Dimming Rearview Mirror with Compass Your vehicle may have an automatic-dimming rearview mirror with a compass. Mirror Operation When turned on, this mirror automatically dims to the proper level to minimize glare from any headlamps behind you after dark. O (On/Off): This is the on/off button for the automatic dimming feature and compass. Press the far left button, located below the mirror face, for up to three seconds to turn the feature on and off. A light on the mirror will be lit while the feature is turned on. Compass Operation Press the on/off button once to turn the compass on or off. There is a compass display in the window in the upper right corner of the mirror face. The compass displays a maximum of two characters. For example, “NE” is displayed for north-east. 2-32 Compass Calibration Press and hold the on/off button down for nine seconds to activate the compass calibration mode. CAL will be displayed in the compass window on the mirror. The compass can be calibrated by driving the vehicle in circles at 5 mph (8 km/h) or less until the display reads a direction. Compass Variance Compass variance is the difference between earth’s magnetic north and true geographic north. The mirror is set to zone eight upon leaving the factory. It will be necessary to adjust the compass to compensate for compass variance if you live outside zone eight. Under certain circumstances, such as during a long distance cross-country trip, it will be necessary to adjust for compass variance. If not adjusted to account for compass variance, your compass could give false readings. To adjust for compass variance, do the following: 1. Find your current location and variance zone number on the map. 2. Press and hold the on/off button for six seconds. Release the button when ZONE is displayed. The number shown is the current zone number. 3. Scroll through the zone numbers that appear in the compass/temperature window on the mirror by pressing the on/off button. Once you ﬁnd your zone number, release the button. After about four seconds, the mirror will return to the compass display, and the new zone number will be set. 2-33 Outside Power Mirrors The controls are located on the driver’s door armrest. Move the upper selector switch to the left or right to choose the mirror to be adjusted, then press the dots, located below the selector switch on the four-way control pad, to adjust the direction of each mirror. The mirrors may also include a memory function which works in conjunction with the memory seats. See Memory Seat on page 2-47 for more information. Power Folding Mirrors To fold or unfold the mirrors, move the selector switch, located above the mirror control, to the middle position. The mirror control will illuminate. Press the right or left side of the mirror control to fold or unfold the mirrors. The mirror will adjust as it folds in and will reposition itself once it is unfolded. If the mirrors are accidentally folded/unfolded manually, they may shake or ﬂutter at normal driving speeds and may not stay in the unfolded position. If this happens, the mirrors need to be reset. See “Resetting the Power Folding Mirrors” next. Resetting the Power Folding Mirrors The power folding mirrors will need to be reset if: They are accidently manually folded/unfolded. The mirrors will not stay in the unfolded position. The mirrors shake and ﬂutter at normal driving speeds. To reset the power folding mirrors, fold and unfold them at least three times using the mirror controls. This will reset them to their normal detent position. 2-34 (cid:127) (cid:127) (cid:127) Outside Convex Mirror Outside Heated Mirrors {CAUTION: A convex mirror can make things (like other vehicles) look farther away than they really are. If you cut too sharply into the right lane, you could hit a vehicle on your right. Check your inside mirror or glance over your shoulder before changing lanes. The passenger’s side mirror is convex. A convex mirror’s surface is curved so more can be seen from the driver’s seat. It makes things in the mirror appear farther away than they really are. The button to turn the heated mirrors on or off is located on the climate control panel. Press this button to warm the driver’s and passenger’s outside rearview mirrors to help clear them of ice, snow, and condensation. See “Rear Window Defogger” under Dual Automatic Climate Control System on page 3-24 for more information. 2-35 Outside Automatic Dimming Mirror with Curb View Assist Your vehicle may have this feature. The driver’s outside mirror will adjust for the glare of the headlamps behind you. See Automatic Dimming Rearview Mirror with OnStar®, Compass and Temperature Display on page 2-29. Your vehicle’s mirrors will also be capable of performing the curb view assist mirror function. This feature will cause the passenger’s and/or driver’s mirror to tilt to a preselected position when the vehicle is in REVERSE (R). This feature may be useful in allowing you to view the curb when you are parallel parking. When the vehicle is shifted out of REVERSE (R) and a short delay has occurred, the passenger’s and/or driver’s mirror will return to its original position. To change the preselected tilt position, adjust the mirrors to the desired position while the vehicle is in REVERSE (R). When the vehicle is shifted out of REVERSE (R), this new position is saved in memory as the tilt position. This feature can be enabled/disabled through the Driver Information Center. See DIC Vehicle Customization on page 3-63 for more information. 2-36 OnStar® System OnStar® uses global positioning system (GPS) satellite technology, wireless communications, and live advisors to provide you with a wide range of safety, security, information, and convenience services. If your airbags deploy, the system is designed to make an automatic call to OnStar® Emergency where we can request emergency services be sent to your location. If you lock your keys in the car, call OnStar® at 1-888-4-ONSTAR and they can send a signal to unlock your doors. If you need roadside assistance, press the OnStar® button and they will get you the help you need. A complete OnStar® User’s Guide and the Terms and Conditions of the OnStar® Subscription Service Agreement are included in the vehicle’s glove box literature. For more information, visit www.onstar.com or www.onstar.ca. Contact OnStar® at 1-888-4-ONSTAR (1-888-466-7827), or press the OnStar® button to speak to an OnStar® advisor 24 hours a day, 7 days a week. Terms and conditions of the Subscription Service Agreement can be found at www.onstar.com or www.onstar.ca. OnStar® Services The OnStar® Directions and Connections Plan is included on new vehicles for the ﬁrst year from the date of purchase. You can extend this plan beyond the ﬁrst year to meet your needs. For more information, press the OnStar® button to speak with an advisor. Directions and Connections Plan (cid:127) Automatic Notiﬁcation of Airbag Deployment (cid:127) Emergency Services (cid:127) Roadside Assistance (cid:127) Stolen Vehicle Tracking (cid:127) AccidentAssist (cid:127) Remote Door Unlock/Vehicle Alert (cid:127) Remote Diagnostics (cid:127) Online Concierge (cid:127) Driving Directions (cid:127) RideAssist Information and Convenience Services OnStar® Personal Calling As an OnStar® subscriber, the Personal Calling capability allows you to make hands-free calls using a wireless system that is integrated into the vehicle. Calls can be placed nationwide using simple voice commands with no additional contracts and no additional roaming charges. To ﬁnd out more about OnStar® Personal Calling, refer to the OnStar® User’s Guide in the vehicle’s glove box, visit www.onstar.com or www.onstar.ca, or speak to an OnStar® advisor by pressing the OnStar® button or calling 1-888-4-ONSTAR (1-888-466-7827). OnStar® Virtual Advisor Your vehicle may have Virtual Advisor. It is a feature of OnStar® Personal Calling that uses your minutes to access weather, local traffic reports and sports updates. By pressing the phone button and giving a few simple voice commands, you can browse through the various topics. Customize your information proﬁle at www.myonstar.com. See the OnStar® user’s guide for more information. 2-37 (cid:127) OnStar® Steering Wheel Controls Your vehicle may be equipped with a Talk/Mute button that can be used to interact with OnStar®. See Audio Steering Wheel Controls on page 3-103 for more information. When calling into voice mail systems or to dial directory numbers, press the control, wait for the “number please” response, say the number(s) to be dialed, wait for the number(s) to be repeated and then say “dial.” See the OnStar® User’s Guide for more information. 2-38 Universal Home Remote System The Universal Home Remote System, a combined universal transmitter and receiver, provides a way to replace up to three hand-held transmitters used to activate devices such as gate operators, garage door openers, entry door locks, security systems, and home lighting. If your vehicle is equipped with the Universal Home Remote Transmitter, it complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This device complies with RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference received, including interference that may cause undesired operation of the device. Changes and modiﬁcations to this system by other than an authorized service facility could void authorization to use this equipment. Universal Home Remote System Operation Do not use the Universal Home Remote with any garage door opener that does not have the “stop and reverse” feature. This includes any garage door opener model manufactured before April 1, 1982. If you have a newer garage door opener with rolling codes, please be sure to follow Steps 6 through 8 to complete the programming of your Universal Home Remote Transmitter. Read the instructions completely before attempting to program the Universal Home Remote. Because of the steps involved, it may be helpful to have another person available to assist you in the programming steps. Keep the original hand-held transmitter for use in other vehicles as well as for future Universal Home Remote programming. It is also recommended that upon the sale of the vehicle, the programmed Universal Home Remote buttons should be erased for security purposes. See “Erasing Universal Home Remote Buttons” later in this section or, for assistance, see Customer Assistance Offices on page 7-4. Be sure that people and objects are clear of the garage door or gate operator you are programming. When programming a garage door, it is advised to park outside of the garage. It is recommended that a new battery be installed in your hand-held transmitter for quicker and more accurate transmission of the radio-frequency signal. Programming Universal Home Remote Follow these steps to program up to three channels: 1. Press and hold down the two outside Universal Home Remote buttons, releasing only when the Universal Home Remote indicator light begins to ﬂash, after 20 seconds. Do not hold down the buttons for longer than 30 seconds and do not repeat this step to program a second and/or third hand-held transmitter to the remaining two Universal Home Remote buttons. 2-39 2. Position the end of your hand-held transmitter about 1 to 3 inches (3 to 8 cm) away from the Universal Home Remote buttons while keeping the indicator light in view. 3. Simultaneously press and hold both the desired Universal Home Remote button and the hand-held transmitter button. Do not release the buttons until Step 4 has been completed. Some entry gates and garage door openers may require you to substitute Step 3 with the procedure noted in “Gate Operator and Canadian Programming” later in this section. 4. The indicator light will ﬂash slowly at ﬁrst and then rapidly after Universal Home Remote successfully receives the frequency signal from the hand-held transmitter. Release both buttons. 5. Press and hold the newly-trained Universal Home Remote button and observe the indicator light. If the indicator light stays on constantly, programming is complete and your device should activate when the Universal Home Remote button is pressed and released. To program the remaining two Universal Home Remote buttons, begin with Step 2 under “Programming Universal Home Remote.” Do not repeat Step 1 as this will erase all of the programmed channels. 2-40 If the indicator light blinks rapidly for two seconds and then turns to a constant light, continue with Steps 6 through 8 following to complete the programming of a rolling-code equipped device, most commonly, a garage door opener. 6. Locate in the garage, the garage door opener receiver (motor-head unit). Locate the “Learn” or “Smart” button. This can usually be found where the hanging antenna wire is attached to the motor-head unit. 7. Firmly press and release the “Learn” or “Smart” button. The name and color of the button may vary by manufacturer. You will have 30 seconds to start Step 8. 8. Return to the vehicle. Firmly press and hold the programmed Universal Home Remote button for two seconds, then release. Repeat the press/hold/release sequence a second time, and depending on the brand of the garage door opener, or other rolling code device, repeat this sequence a third time to complete the programming. The Universal Home Remote should now activate your rolling-code equipped device. To program the remaining two Universal Home Remote buttons, begin with Step 2 of “Programming Universal Home Remote.” You do not want to repeat Step 1, as this will erase all previous programming from the Universal Home Remote buttons. Gate Operator and Canadian Programming Canadian radio-frequency laws require transmitter signals to time out or quit after several seconds of transmission. This may not be long enough for Universal Home Remote to pick up the signal during programming. Similarly, some U.S. gate operators are manufactured to time out in the same manner. If you live in Canada, or you are having difficulty programming a gate operator or garage door opener by using the “Programming Universal Home Remote” procedures, regardless of where you live, replace Step 3 under “Programming Universal Home Remote” with the following: Continue to press and hold the Universal Home Remote button while you press and release every two seconds (cycle) the hand-held transmitter button until the frequency signal has been successfully accepted by the Universal Home Remote. The Universal Home Remote indicator light will ﬂash slowly at ﬁrst and then rapidly. Proceed with Step 4 under “Programming Universal Home Remote” to complete. Using Universal Home Remote Press and hold the appropriate Universal Home Remote button for at least half of a second. The indicator light will come on while the signal is being transmitted. Erasing Universal Home Remote Buttons To erase programming from the three Universal Home Remote buttons do the following: 1. Press and hold down the two outside buttons until the indicator light begins to ﬂash, after 20 seconds. Do not hold the two outside buttons for longer than 30 seconds. 2. Release both buttons. The Universal Home Remote is now in the train (learning) mode and can be programmed at any time beginning with Step 2 under “Programming Universal Home Remote” shown earlier in this section. Individual buttons cannot be erased, but they can be reprogrammed. See “Reprogramming a Single Universal Home Remote Button” following this section. 2-41 Reprogramming a Single Universal Home Remote Button To program a device to Universal Home Remote using a Universal Home Remote button previously trained, follow these steps: 1. Press and hold the desired Universal Home Remote button. Do not release the button. 2. The indicator light will begin to ﬂash after 20 seconds. While still holding the Universal Home Remote button, proceed with Step 2 under “Programming Universal Home Remote” shown earlier in this section. For additional information on Universal Home Remote, see Customer Assistance Offices on page 7-4. Storage Areas Glove Box Open the glove box by pulling the bottom of the handle upward. 2-42 Cupholder(s) Your vehicle is equipped with cupholders for the front and rear passengers. The cupholders are located in the center console for the front passengers and on the rear of the center console for the rear passengers. To use the front cupholders, press down on the access door and release. The door will then open. Push the door back down to close it. The front cupholder may be removed for cleaning by pushing down and then back on the cupholder. Some vehicles may be equipped with a heated and cooled front cupholders. Perform the following procedure to use your front cupholders: 1. Place the provided beverage container in the cup holder. 2. Press the top (red dot) of the switch to heat the cup holder or press the bottom (blue dot) of the switch to cool the cup holder. Press the same switch again to turn off the cup holder. If you dim your interior lights to the lowest setting, the cupholder will automatically shutoff. This prevents the cupholder from being on when the indicator light may be too dim to see. To use your cupholder, adjust the interior lights to a brighter setting. To use the rear cupholders, pull down on the door located on the back of the console. Your rear seat armrest, if equipped, may also contain cupholders. Instrument Panel Storage Area Your vehicle may have a closed storage area on the instrument panel above the compact disc changer. You can open the storage area by pressing in the bottom of the lid and the lid will automatically raise up. Press down on the lid to close the storage area. Center Console Storage Area Your vehicle has a console compartment between the bucket seats. To open it, press the button on the side of the console and swing the console lid open. The console may be equipped with an accessory power outlet inside. See Accessory Power Outlet(s) on page 3-22. The rear of the console also has a cupholder that swings down for the rear seat passengers to use. Luggage Carrier You can load things on top of your vehicle if it has this feature. The luggage carrier has slats and siderails attached to the roof and may have crossrails which can be moved back and forth to help secure cargo. Tie the load to the siderails or siderail supports. Notice: Loading cargo on the luggage carrier that weighs more than 200 lbs (91 kg) or hangs over the rear or sides of the vehicle may damage your vehicle. Load cargo so that it rests on the slats as far forward as possible and against the side rails, making sure to fasten it securely. Don’t exceed the maximum vehicle capacity when loading your vehicle. For more information on vehicle capacity and loading, see Loading Your Vehicle on page 4-46. 2-43 To prevent damage or loss of cargo as you’re leaving, check now and then to make sure the luggage and cargo are still securely fastened. Be sure the cargo is properly loaded. Your vehicle has a Center High-Mounted Stoplamp (CHMSL) located above the rear glass. If items are loaded on the roof of the vehicle, care should be taken not to block or damage the CHMSL unit. If small heavy objects are placed on the roof cut a piece of 3/8 inch plywood to ﬁt inside the crossrails and siderails to spread the load. If plywood is used, tie it to the siderail supports. Tie the load to the crossrails or the siderail supports. Use the crossrails only to keep the load from sliding. To move a crossrail, turn the release knobs, on both sides of the rail, counterclockwise to loosen it. Slide the crossrail to the desired position balancing the force side to side. Turn the release knobs, on both sides of the rail, clockwise to tighten it and try to slide the crossrail back and forth slightly to be sure it is tight. If you need to carry long items, move the crossrails as far apart as they will go. Tie the load to the crossrails and the siderails or siderail supports. Also tie the load to the bumpers. Do not tie the load so tightly that the crossrails or siderails are damaged. (cid:127) After moving a crossrail, be sure it is securely locked into the siderail. Rear Seat Armrest Your vehicle’s second row seat may have an armrest/storage compartment. Pull the loop at the top of the armrest out to lower the armrest. To open the compartment, if equipped, push the button on the front of the armrest and pull the top open. Convenience Net The convenience net (if equipped) in the rear of your vehicle helps to keep small loads in place during sharp turns or quick stops and starts. The net is not designed for larger, heavier items. To install the net, attach the hooks to the raised cargo tie downs. Then, attach the cord loops to the button retainers in the side trim. You can unhook the net so that it will lie ﬂat when you’re not using it. 2-44 (cid:127) (cid:127) (cid:127) Cargo Cover {CAUTION: An improperly stored cargo cover could be thrown about the vehicle during a collision or sudden maneuver. You or others could be injured. If you remove the cover, always store it in the proper storage location. When you put it back, always be sure that it is securely reattached. If you have a cargo cover, you can use it to cover items in the cargo area of your vehicle. To use the cover, do the following: 1. Pull the cover handle toward the rear of the vehicle. 2. Latch the cover posts into the retaining sockets on the cargo area trim panels. To return the cover to the retracted position, do the following: 1. Pull up on the cover handle to release the cover posts from the retaining sockets. 2. Let the cover move forward to the full retracted position. To remove the cover from the vehicle, do the following: 1. Let the cover go all the way into the holder. 2. Then, grasping the passenger’s side cover endcap, push the cover endcap toward the driver’s side of the vehicle. The endcap should lock in the compressed position. 3. Lift the cover up on the passenger’s side, swing the cover rearward and take it out of the vehicle. To put the cover in the vehicle, do the following: 1. Make sure the cover slot in the holder faces rearward with the round surface facing down. 2. Then, hold the cover at an angle and place the cover holder tab into the slot in the driver’s side trim panel. 3. Move the other end of the cover forward and hold it next to the passenger’s side trim panel slot. 4. Push the button on top of the passenger’s side endcap. This will allow the cover to extend into the trim slot. 5. Lightly pull on the cover holder to make sure it is secure. On some models there are two slots. The slots furthest forward allow the cover to be used if the third seat is removed or folded down. 2-45 Cargo Tie Downs Sunroof Your vehicle may be equipped with cargo tie downs in the rear cargo area that allow you to strap cargo in and keep it from moving inside the vehicle. Your vehicle may be equipped with a power sliding sunroof. To open or close your sunroof, the ignition needs to be on or RAP needs to be active. See “Retained Accessory Power” under Ignition Positions on page 2-17. Press and release the rear side of the button located in the front overhead console to express-open the glass panel and sunshade. To stop the express-open motion, press the front or rear of the button again. To close the glass panel, press and hold the front of the button. The glass will not be fully seated unless the button is held until the glass stops moving. With the sunroof closed, press the forward side of the button to open the sunroof to the vent position. The sunroof is also equipped with a sunshade which you can pull forward to block sun rays. When not using the tie downs, ﬂip them down out of the way. 2-46 If a hand, arm, or other object is blocking the sunroof glass panel as it is closing, the glass panel will stop at the obstruction. After the obstruction is removed, the glass panel can be closed or opened. Use care not to leave the sunroof open for long periods of time as debris may collect in the tracks. If the battery has been recharged, disconnected or is not working, you may need to reprogram the sunroof. To do this, start the vehicle and press the forward side of the sunroof button until the glass panel moves to a fully closed position. Release, and press again to move to the vent position, which occurs when the sunroof is fully tilted upward and the button is held for an additional twenty seconds. This will reset the memory and enable the sunroof to function properly. Vehicle Personalization In addition to the following features, your vehicle may also have features that can be programmed through the Driver Information Center (DIC). See DIC Vehicle Customization on page 3-63 for more information. Memory Seat If your vehicle has this feature, the controls for the memory function are located on the driver’s door. These buttons are used to program and recall memory settings for the driver’s seat, both the driver’s and passenger’s outside mirrors, and the throttle and brake pedals for vehicles with the adjustable throttle and brake pedal feature. The settings for these features can be saved for up to two drivers. 2-47 To store the seat exit position, do the following: 1. Press and release the 1 or 2 button. The seat will move to the stored memory position. 2. Adjust the seat to the desired exit position. 3. Press and hold the exit button of the memory control for three seconds. A double chime will sound to let you know that the position has been stored for the selected button (1 or 2). To repeat the procedure for a second driver, follow the preceding steps, but press the other numbered memory control button. To use the seat exit position, do one of the following: (cid:127) Press the exit button on the memory control. If this feature is activated in the Driver Information Center (DIC), removing the key from the ignition will move the seat to the exit position. See “Easy Exit Seat” under DIC Vehicle Customization on page 3-63 for more information on activating this feature in the DIC. To store the settings, do the following: 1. While the vehicle is in PARK (P), adjust the driver’s seat, including the seatback recliner, lumbar, and side wing area, both of the outside mirrors, and the throttle and brake pedals to your preference. 2. Press and hold the 1 or 2 button of the memory control for three seconds. A double chime will sound to let you know that the position has been stored. To repeat the procedure for a second driver, follow the preceding steps, but press the other numbered memory control button. Each time button 1 or 2 is pressed and released while the vehicle is in PARK (P), a single chime will sound and the memory position will be recalled. To stop recall movement of the memory seat feature at any time, press one of the memory buttons or power seat controls. Easy Exit Seat The controls for this memory function are located on the driver’s door. B (Easy Exit Seat): This button is used to program and recall the desired driver’s seat position when exiting or entering the vehicle. The seat position can be saved for up to two drivers. 2-48 (cid:127) Section 3 Instrument Panel Instrument Panel Overview ...............................3-4 Hazard Warning Flashers ................................3-6 Other Warning Devices ...................................3-6 Horn .............................................................3-6 Tilt Wheel .....................................................3-6 Turn Signal/Multifunction Lever .........................3-7 Turn and Lane-Change Signals ........................3-8 Headlamp High/Low-Beam Changer ..................3-9 Flash-to-Pass .................................................3-9 Windshield Wipers ........................................3-10 Windshield Washer .......................................3-10 Rear Window Wiper/Washer ...........................3-11 Cruise Control ..............................................3-12 Exterior Lamps .............................................3-15 Headlamps on Reminder ................................3-16 Daytime Running Lamps (DRL) .......................3-16 Automatic Headlamp System ..........................3-17 Fog Lamps ..................................................3-18 Instrument Panel Brightness ...........................3-18 Dome Lamps ...............................................3-19 Entry/Exit Lighting .........................................3-19 Reading Lamps ............................................3-19 Battery Run-Down Protection ..........................3-19 Ultrasonic Rear Parking Assist (URPA) ............3-20 Accessory Power Outlet(s) .............................3-22 Ashtray(s) and Cigarette Lighter ......................3-23 Analog Clock ...............................................3-23 Climate Controls ............................................3-24 Dual Automatic Climate Control System ...........3-24 Outlet Adjustment .........................................3-29 Rear Climate Control System .........................3-30 Warning Lights, Gages, and Indicators ............3-32 Instrument Panel Cluster ................................3-33 Speedometer and Odometer ...........................3-34 Trip Odometer ..............................................3-34 Tachometer .................................................3-34 Safety Belt Reminder Light .............................3-34 Airbag Readiness Light ..................................3-35 Passenger Airbag Status Indicator ...................3-36 Charging System Light ..................................3-38 Voltmeter Gage ............................................3-38 Brake System Warning Light ..........................3-39 Anti-Lock Brake System Warning Light .............3-40 Low Tire Pressure Warning Light ....................3-41 Traction Off Light ..........................................3-41 Engine Coolant Temperature Gage ..................3-42 Transmission Temperature Gage .....................3-42 3-1 Section 3 Instrument Panel Malfunction Indicator Lamp .............................3-44 Oil Pressure Gage ........................................3-46 Security Light ...............................................3-47 Cruise Control Light ......................................3-48 Highbeam On Light .......................................3-48 Tow/Haul Mode Light ....................................3-48 Fuel Gage ...................................................3-49 Low Fuel Warning Light .................................3-49 Driver Information Center (DIC) .......................3-50 DIC Operation and Displays ...........................3-50 DIC Warnings and Messages .........................3-54 DIC Vehicle Customization .............................3-63 Audio System(s) .............................................3-69 Setting the Time ...........................................3-70 Radio with Cassette and CD ..........................3-71 Navigation/Radio System ...............................3-86 Rear Seat Entertainment System ....................3-86 Rear Seat Audio (RSA) .................................3-97 CD Changer ................................................3-99 Theft-Deterrent Feature ................................3-102 Audio Steering Wheel Controls ......................3-103 Radio Reception .........................................3-103 Care of the Cassette Tape Player .................3-104 Care of Your CDs and DVDs ........................3-105 Care of the CD and DVD Player ...................3-105 Diversity Antenna System .............................3-106 XM™ Satellite Radio Antenna System ............3-106 Chime Level Adjustment ...............................3-106 3-2 ✍ NOTES 3-3 Instrument Panel Overview 3-4 The main components of your instrument panel are the following: A. Air Outlets. See Outlet Adjustment on page 3-29. B. Exterior Lamps Control. See Exterior Lamps on page 3-15. C. Turn Signal/Multifunction Lever. See Turn Signal/Multifunction Lever on page 3-7. D. OnStar® and Radio Steering Wheel Buttons. See OnStar® System on page 2-36 and Audio Steering Wheel Controls on page 3-103. E. Instrument Panel Cluster. See Instrument Panel Cluster on page 3-33. F. Shift Lever/Tow/Haul Selector Button. See Automatic Transmission Operation on page 2-20 and Tow/Haul Mode on page 2-23. G. Audio System. See Audio System(s) on page 3-69. H. Dome Override Button. See Dome Lamps on page 3-19. I. Rear Wiper Washer. See Windshield Washer on page 3-10. J. Fog Lamps Button. See Fog Lamps on page 3-18. K. Driver Information Center (DIC) Buttons. See Driver Information Center (DIC) on page 3-50. L. Parking Brake Release. See Parking Brake on page 2-23. M. Tilt Lever. See Tilt Wheel on page 3-6. N. Climate Control System. See Dual Automatic Climate Control System on page 3-24. O. Compact Disc Changer. See CD Changer on page 3-99. P. Storage Area. See Instrument Panel Storage Area on page 2-43. Q. Analog Clock. See Analog Clock on page 3-23. R. Ultrasonic Rear Parking Assist Disable Button. See Ultrasonic Rear Parking Assist (URPA) on page 3-20. S. StabiliTrak® Disable Button. See StabiliTrak® System on page 4-9. T. Glove Box. See Glove Box on page 2-42. 3-5 Hazard Warning Flashers Your hazard warning ﬂashers let you warn others. They also let police know you have a problem. Your front and rear turn signal lamps will ﬂash on and off. Horn To sound the horn, press the center pad on the steering wheel. The hazard warning ﬂasher button is located on top of the steering column. Tilt Wheel The tilt steering wheel allows you to adjust the steering wheel before you drive. You can raise it to the highest level to give your legs more room when you enter and exit the vehicle. Your hazard warning ﬂashers work no matter what position your key is in, and even if the key is not in the ignition. Press the button to make the front and rear turn signal lamps ﬂash on and off. Press the button again to turn the ﬂashers off. When the hazard warning ﬂashers are on, your turn signals will not work. Other Warning Devices If you carry reﬂective triangles, you can set them up at the side of the road about 300 feet (100 m) behind your vehicle. 3-6 The tilt lever is located on the driver’s side of the steering column under the turn signal lever. To tilt the wheel, hold the steering wheel and pull the lever. Move the steering wheel to a comfortable level, then release the lever to lock the wheel in place. Turn Signal/Multifunction Lever The lever on the left side of the steering column includes the following: (cid:127) G Turn and Lane Change Signals. Turn and Lane-Change Signals on page 3-8. (cid:127) 53 Headlamp High/Low-Beam Changer. Headlamp High/Low-Beam Changer on page 3-9. Flash-to-Pass Feature. See Flash-to-Pass on page 3-9. (cid:127) N Windshield Wipers. See Windshield Wipers on page 3-10. (cid:127) L Windshield Washer. See Windshield Washer on page 3-10. (cid:127) I Cruise Control. Cruise Control on page 3-12. For information on the exterior lamps, see Exterior Lamps on page 3-15 later in this section. 3-7 (cid:127) Turn and Lane-Change Signals The turn signal has two upward (for right) and two downward (for left) positions. These positions allow you to signal a turn or a lane change. To signal a turn, move the lever all the way up or down. When the turn is ﬁnished, the lever will return automatically. To signal a lane change, just raise or lower the lever until the arrow starts to ﬂash. Hold it there until you complete your lane change. The lever will return by itself when you release it. An arrow on the instrument panel cluster will ﬂash in the direction of the turn or lane change. As you signal a turn or a lane change, if the arrows ﬂash more quickly than normal, a signal bulb may be burned out and other drivers won’t see your turn signal. If a bulb is burned out, replace it to help avoid an accident. If the arrows don’t go on at all when you signal a turn, check for burned-out bulbs and a blown fuse. See Instrument Panel Fuse Block on page 5-108 and Underhood Fuse Block on page 5-111. Turn Signal On Chime If your turn signal is left on for more than 3/4 of a mile (1.2 km), a chime will sound at each ﬂash of the turn signal and the message TURN SIGNAL ON will also appear in the DIC. See DIC Warnings and Messages on page 3-54. To turn the chime and message off, move the turn signal lever to the off position. 3-8 Headlamp High/Low-Beam Changer 53(Headlamp High/Low Beam Changer): To change the headlamps from low to high beam, push the lever toward the instrument panel. To return to low-beam headlamps, pull the multifunction lever toward you. Then release it. When the high beams are on, this indicator light on the instrument panel cluster will also be on. Flash-to-Pass This feature lets you use your high-beam headlamps to signal a driver in front of you that you want to pass. It works even if your headlamps are in the automatic position. To use it, pull the turn signal lever toward you, then release it. If your headlamps are in the automatic position or on low beam, your high-beam headlamps will turn on. They’ll stay on as long as you hold the lever toward you. The high-beam indicator on the instrument panel cluster will come on. Release the lever to return to normal operation. 3-9 Windshield Washer L (Washer Fluid): There is a paddle marked with the windshield washer symbol at the top of the multifunction lever. To spray washer ﬂuid on the windshield, push the paddle. The wipers will clear the window and then either stop or return to your preset speed. {CAUTION: In freezing weather, do not use your washer until the windshield is warmed. Otherwise the washer ﬂuid can form ice on the windshield, blocking your vision. Windshield Wipers You control the windshield wipers by turning the band with the wiper symbol on it. 8(Mist): For a single wiping cycle, turn the band to mist. Hold it there until the wipers start. Then let go. The wipers will stop after one wipe. If you want more wipes, hold the band on mist longer. N (Delay): You can set the wiper speed for a long or short delay between wipes. This can be very useful in light rain or snow. Turn the band to choose the delay time. The closer to the top of the lever, the shorter the delay. 6 (Low Speed): For steady wiping at low speed, turn the band away from you to the ﬁrst solid band past the delay settings. 1 (High Speed): For high-speed wiping, turn the band further, to the second solid band past the delay settings. 9(Off): To stop the wipers, move the band to off. Be sure to clear ice and snow from the wiper blades before using them. If they’re frozen to the windshield, carefully loosen or thaw them. If your blades do become worn or damaged, get new blades or blade inserts. 3-10 Rear Window Wiper/Washer {CAUTION: In freezing weather, do not use your washer until the windshield is warmed. Otherwise the washer ﬂuid can form ice on the windshield, blocking your vision. If your vehicle has a rear window washer/wiper, this knob is located on the instrument panel to the left of the steering wheel. To turn the rear wiper on, turn the knob to either 1 or 2. For long delayed wiping, turn the knob to 1. For short delayed wiping, turn the knob to 2. 9(Off): To turn the wiper off, turn the knob to this symbol. = (Washer Fluid): To wash the window, press the knob with this symbol. The rear window washer uses the same ﬂuid bottle as the windshield washer. However, the rear window washer will run out of ﬂuid before the windshield washer. If you can wash your windshield but not your rear windows, check the ﬂuid level. 3-11 Cruise Control 9(Off): This position turns the system off. With cruise control, you can maintain a speed of about 25 mph (40 km/h) or more without keeping your foot on the accelerator. This can really help on long trips. Cruise control does not work at speeds below about 25 mph (40 km/h). If you apply your brakes, the cruise control will shut off. R (On): This position activates the system. + (Resume/Accelerate): Push the lever to this symbol to make the vehicle accelerate or resume to a previously set speed. T (Set): Press this button to set the speed. {CAUTION: Cruise control can be dangerous where you cannot drive safely at a steady speed. So, do not use your cruise control on winding roads or in heavy traffic. Cruise control can be dangerous on slippery roads. On such roads, fast changes in tire traction can cause needless wheel spinning, and you could lose control. Do not use cruise control on slippery roads. 3-12 Resuming a Set Speed Suppose you set your cruise control at a desired speed and then you apply the brake. This, of course, disengages the cruise control. But you do not need to reset it. Once you’re going about 25 mph (40 km/h) or more, you can move the cruise control switch brieﬂy from on to resume/accelerate. You will go right back up to your chosen speed and stay there. If you hold the switch at resume/accelerate the vehicle will keep going faster until you release the switch or apply the brake. So unless you want to go faster, do not hold the switch at resume/accelerate. Setting Cruise Control {CAUTION: If you leave your cruise control on when you are not using cruise, you might hit a button and go into cruise when you do not want to. You could be startled and even lose control. Keep the cruise control switch off until you want to use cruise control. 1. Move the cruise control switch to on. 2. Get up to the speed you want. 3. Press in the set button at the end of the lever and release it. 4. Take your foot off the accelerator pedal. The cruise light on the instrument panel will illuminate when the cruise control is engaged. 3-13 Increasing Speed While Using Cruise Control There are two ways to go to a higher speed: (cid:127) Use the accelerator pedal to get to the higher speed. Press the set button at the end of the lever, then release the button and the accelerator pedal. You will now cruise at the higher speed. If the accelerator pedal is held longer than 60 seconds, cruise control will turn off. (cid:127) Move the cruise switch from on to resume/ accelerate. Hold it there until you get up to the speed you want, and then release the switch. To increase your speed in very small amounts, move the switch brieﬂy to resume/accelerate. Each time you do this, your vehicle will go about 1 mph (1.6 km/h) faster. Reducing Speed While Using Cruise Control (cid:127) Press in the button at the end of the lever until you reach the lower speed you want, then release it. To slow down in very small amounts, brieﬂy press the set button. Each time you do this, you will go about 1 mph (1.6 km/h) slower. 3-14 Passing Another Vehicle While Using Cruise Control Use the accelerator pedal to increase your speed. When you take your foot off the pedal, your vehicle will slow down to the cruise control speed you set earlier. Using Cruise Control on Hills How well your cruise control will work on hills depends upon your speed, load and the steepness of the hills. When going up steep hills, you may want to step on the accelerator pedal to maintain your speed. When going downhill, you may have to brake or shift to a lower gear to keep your speed down. Of course, applying the brake takes you out of cruise control. Many drivers ﬁnd this to be too much trouble and do not use cruise control on steep hills. Ending Cruise Control To turn off the cruise control, do one of the following: (cid:127) Step lightly on the brake pedal. (cid:127) Move the cruise control switch to off. (cid:127) Shift the transmission to NEUTRAL (N). If road conditions cause StabiliTrak® to activate, cruise control will turn off. If the accelerator pedal is held longer than 60 seconds, cruise control will turn off. (cid:127) (cid:127) (cid:127) The cruise control will turn off automatically if the traction control system or StabiliTrak® system activate, if your vehicle is equipped with either feature. Erasing Speed Memory When you turn off the cruise control or the ignition, your cruise control set speed memory is erased. Exterior Lamps The control on the driver’s side of your instrument panel operates the exterior lamps. The exterior lamp control has four positions: 9(Off): Turn the knob to this position and release it to turn off all exterior lamps including the DRL. To turn any lamps back on when in the off mode, turn the knob to the desired lamp mode. To return to the AUTO mode, turn the knob to the off position and release it. The off or AUTO mode will also cancel and the lamps will return to the AUTO when the vehicle is turned off. This mode is not available for vehicles sold in Canada. AUTO: Turn the control to this position to put the system into automatic headlamp mode. The Daytime Running Lamps (DRL) will also be activated if it is light enough outside. ; (Parking Lamps): Turn the control to this position to turn on the parking lamps, together with the following: (cid:127) Sidemarker Lamps Taillamps License Plate Lamps Instrument Panel Lights 3-15 (cid:127) (cid:127) (cid:127) 2(Headlamps): Turn the control to this position to turn on the headlamps, together with the previously listed lamps and lights. When the vehicle is turned off and the headlamps are in AUTO, the headlamps may automatically remain on for a set time. You can change this delay time using the DIC. See Driver Information Center (DIC) on page 3-50. You can switch your headlamps from low to high-beam by pushing the turn signal/multifunction lever toward the instrument panel. Daytime Running Lamps (DRL) Daytime Running Lamps (DRL) can make it easier for others to see the front of your vehicle during the day. DRL can be helpful in many different driving conditions, but they can be especially helpful in the short periods after dawn and before sunset. Fully functional daytime running lamps are required on all vehicles ﬁrst sold in Canada. The DRL system will come on when the following conditions are met: Headlamps on Reminder If a door is open, a reminder chime will sound when your headlamps or parking lamps are manually turned on and your key is out of the ignition. To turn off the chime, turn the headlamp switch to off or AUTO and then back on. In the AUTO mode, the headlamps turn off once the ignition is in LOCK or may remain on until the headlamp delay ends (if enabled in the DIC). The ignition is on, the exterior lamps control is in AUTO, the transmission is not in PARK (P), and the light sensor determines it is daytime. When the DRL are on, only your DRL lamps will be on. The taillamps, sidemarker and other lamps won’t be on. The instrument panel won’t be lit up either. When it begins to get dark, the automatic headlamp system will switch from DRL to the headlamps. As with any vehicle, you should turn on the regular headlamp system when you need it. 3-16 (cid:127) (cid:127) (cid:127) (cid:127) Automatic Headlamp System When it is dark enough outside and the headlamp switch is in AUTO, your automatic headlamp system will turn on your headlamps at the normal brightness along with other lamps such as the taillamps, sidemarker, parking lamps, roof marker lamps and the instrument panel lights. The radio lights will also be dim. To turn off the automatic headlamp system, turn the exterior lamps switch to the off position and then release. Turning off the automatic headlamp system with the headlamp switch is not available for vehicles ﬁrst sold in Canada. For vehicles ﬁrst sold in Canada, you can turn off the automatic headlamp system when parked at night by applying the parking brake before starting your vehicle. The headlamps will remain off once the vehicle is started for as long as you are parked. If you release the parking brake, the lights will turn on. If the parking brake is not released before you begin to drive, the exterior lamps will turn on above 2 mph (3.2 km/h). Your vehicle has a light sensor located on the top of the instrument panel. Be sure it is not covered, or the system will be on whenever the ignition is on. The system may also turn on your headlamps when driving through a parking garage, heavy overcast weather or a tunnel. This is normal. There is a delay in the transition between the daytime and nighttime operation of the Daytime Running Lamps (DRL) and the automatic headlamp systems so that driving under bridges or bright overhead street lights does not affect the system. The DRL and automatic headlamp system will only be affected when the light sensor sees a change in lighting lasting longer than the delay. If you start your vehicle in a dark garage, the automatic headlamp system will come on immediately. Once you leave the garage, it will take approximately one minute for the automatic headlamp system to change to DRL if it is light outside. During that delay, your instrument panel cluster may not be as bright as usual. Make sure your instrument panel brightness control is in the full bright position. See Instrument Panel Brightness on page 3-18. 3-17 Fog Lamps If your vehicle has fog lamps you can use them for better vision in foggy or misty conditions. Your parking lamps and/or low-beam headlamps must be on for your fog lamps to work. The fog lamp button is located on the left side of your instrument panel. Press the button to turn the fog lamps on while the headlamps or parking lamps are on. Press the button again to turn them off. An indicator light will glow near the button when the fog lamps are on. 3-18 Remember, fog lamps alone will not give off as much light as your headlamps. Never use your fog lamps in the dark without turning on the headlamps. The fog lamps will go off whenever your high-beam headlamps come on. When the high beams go off, the fog lamps will come on again. The fog lamps will be cancelled after the ignition is turned off. If you still want to use the fog lamps after you restart the vehicle, you will need to press the fog lamp button again. Some localities have laws that require the headlamps to be on along with the fog lamps. Instrument Panel Brightness The thumbwheel for this feature is located next to the exterior lamps control. D (Instrument Panel Lights): Turn the thumbwheel up or down to brighten or dim the instrument panel lights and the radio display. This will only work if the headlamps or parking lamps are on. To turn on the dome lamps, with the vehicle doors closed, turn the thumbwheel all the way up. Reading Lamps If your vehicle has reading lamps, press the button located next to the lamp to turn it on or off. The lamps can be adjusted to point in the direction you want. Your vehicle may also have reading lamps in other locations. To turn on or off, press the button located next to the lamp. The lamps cannot be adjusted. Battery Run-Down Protection This feature shuts off the dome lamps if they are left on for more than 10 minutes when the ignition is in LOCK. This will keep your battery from running down. Dome Lamps The dome lamps will come on when you open a door, and will turn off when all doors are closed. You can also turn the dome lamps on by turning the thumbwheel, located next to the exterior lamp control, all the way up. In this position, the dome lamps will remain on whether a door is opened or closed. E (Dome Override): Press this button, located below the exterior lamp control, to turn dome lamps off even while a door is opened. To return the lamps to automatic operation, press the button again and it will return to the out position. In this position, the dome lamps will come on when you open a door. Entry/Exit Lighting Your vehicle is equipped with an illuminated entry/exit feature. When a door is opened or the key is removed from the ignition, the dome lamps will come on if the dome override button is in the out position. 3-19 Ultrasonic Rear Parking Assist (URPA) The Ultrasonic Rear Parking Assist (URPA) system is designed to help you park, while the vehicle is in REVERSE (R). It operates only at very low speeds, less than 3 mph (5 km/h). URPA can help make parking easier and to help you avoid colliding with objects such as parked vehicles. The URPA system can detect objects up to 5 feet (1.5 m) behind the vehicle, and tell you how close these objects are from your rear bumper. Your vehicle’s URPA operates when the shift lever is moved into REVERSE (R) and the vehicle speed is less than 3 mph (5 km/h). Four ultrasonic sensors located at the rear bumper are used to detect the distance to the object. 3-20 The URPA display is located inside the vehicle, near the rear window. It has three color-coded lights used to provide distance and system information to the driver. URPA can be turned off by pressing the rear park aid disable button located near the climate control system and radio. You will not see any lights on the rear display if URPA is turned off. {CAUTION: Even with the Ultrasonic Rear Park Assist system, the driver must check carefully before backing up. The system does not operate above typical backing speeds of 3 mph (5 km/h) while parking. And, the system does not detect objects that are more than 5 feet (1.5 meters) behind the vehicle. So, unless you check carefully behind you before and when you back up, you could strike children, pedestrians, bicyclists or pets behind you, and they could be injured or killed. Whether or not you are using rear park assist, always check carefully behind your vehicle before you back up and then watch closely as you do. How the System Works Unless disabled, the URPA will turn on automatically when the shift lever is moved into REVERSE (R). When the system turns on, the three lights on the display will illuminate for one and a half seconds to let you know that the system is working. If your vehicle is moving in REVERSE (R) at a speed greater than 3 mph (5 km/h), the red light will ﬂash to remind you that the system does not work at a speed greater than 3 mph (5 km/h). If an object is detected at a REVERSE (R) speed of less than 3 mph (5 km/h), one of the following will occur: A chime will sound the ﬁrst time an object is detected between 20 inches (0.5 m) and 5 feet (1.5 m) away. Description amber light amber/amber lights amber/amber/red lights & continuous chime amber/amber/red lights ﬂashing & continuous chime English 5 ft 40 in 20 in 1 ft Metric 1.5 m 1.0 m 0.5 m 0.3 m URPA cannot detect objects that are above liftgate level. In order for the rear sensors to recognize an object, it must be within detection range behind the vehicle. 3-21 When the System Does Not Seem to Work Properly The light may ﬂash red when the vehicle is in REVERSE (R) if the ultrasonic sensors are not kept clean. So be sure to keep your rear bumper free of mud, dirt, snow, ice and slush. Other conditions that may affect system performance include things like the vibrations from a jackhammer or the compression of air brakes on a very large truck. If after cleaning the rear bumper and then driving forward at least 15 mph (25 km/h), the display continues to ﬂash red, see your dealer. If a trailer was attached to your vehicle, or a bicycle or an object was on the back of, or hanging out of your cargo area during your last drive cycle, the light may also ﬂash red. The light will continue to ﬂash whenever in REVERSE (R) until your vehicle is driven forward at least 15 mph (25 km/h) without any obstructions behind the vehicle. For cleaning instructions, see Washing Your Vehicle on page 5-101. Accessory Power Outlet(s) With accessory power outlets you can plug in auxiliary electrical equipment such as a cellular telephone or CB radio. Your vehicle is equipped with many accessory power outlets. One outlet is located in the center console. Press the button on the side of the console door to access the outlet. There may also be accessory power outlets located on the back of the center console above the cupholder and in the rear cargo area on the passenger side. Do not try to put the cigarette lighter in any of the accessory outlets. Notice: Adding any electrical equipment to your vehicle may damage it or keep other components from working as they should. The repairs would not be covered by your warranty. Do not use equipment exceeding maximum amperage rating. Check with your dealer before adding electrical equipment. Certain power accessory plugs may not be compatible with the accessory power outlets and could result in blown vehicle or adapter fuses. If you experience a problem, see your dealer for additional information on the accessory power plugs. Notice: damage not covered by your warranty. Do not hang any type of accessory or accessory bracket from the plug because the power outlets are designed for accessory power plugs only. Improper use of the power outlet can cause 3-22 Analog Clock To adjust the clock, do the following: 1. Locate the adjustment button to the lower left corner of the clock. 2. Push and hold the adjustment button to advance the clock hands. Release the button before you get to the desired time. 3. Push and release the button to increase the time by one minute increments until the desired time is reached. If you put papers, pins, or other ﬂammable Ashtray(s) and Cigarette Lighter The front ashtray and lighter are located in the center console near the cupholders, if equipped. Press on the access door to open it and use the ashtray and lighter. Notice: items in the ashtray, hot cigarettes or other smoking materials could ignite them and possibly damage your vehicle. Never put ﬂammable items in the ashtray. To remove the ashtray, pull it from the center console. Slide it back in and push down to be sure it is secure. To use the cigarette lighter, push it in all the way, and let go. When it’s ready, it will pop back out by itself. Notice: Holding a cigarette lighter in while it is heating will not allow the lighter to back away from the heating element when it is hot. Damage from overheating may occur to the lighter or heating element, or a fuse could be blown. Do not hold a cigarette lighter in while it is heating. 3-23 Climate Controls Dual Automatic Climate Control System With this system, you can control the heating, cooling and ventilation in your vehicle. You can select different climate control settings for the driver and passengers. Driver’s Side Temperature Knob The driver’s side knob is used to adjust the temperature of the air coming through the system on the driver’s side. The temperature can be adjusted even if the system is turned off. This is possible since outside air 3-24 will always ﬂow through the system as the vehicle is moving forward unless it is set to recirculation mode. See “Recirculation” later in this section. Turn the knob counterclockwise or clockwise to lower or increase the cabin temperature. The display will show the temperature setting decreasing or increasing and an arrow pointing to the driver will be displayed under and to the left of the temperature setting. Passenger’s Side Temperature Knob The passenger’s side knob can be used to change the temperature of the air coming through the system on the passenger’s side of the vehicle. The temperature can be adjusted even if the system is turned off. This is possible since outside air will always ﬂow through the system as the vehicle is moving forward unless it is set to recirculation mode. See “Recirculation” later in this section. Turn the knob counterclockwise or clockwise to lower or increase the cabin temperature. The display will show the temperature setting decreasing or increasing and an arrow pointing to the passenger will be displayed under and to the right of the temperature setting. The passenger’s temperature setting can be set to match the driver’s temperature setting by pressing and holding the AUTO button for four seconds. Both the driver and passenger arrows will be displayed. Automatic Operation AUTO (Automatic): When automatic operation is active the system will control the inside temperature, the air delivery, and the fan speed. Use the steps below to place the entire system in automatic mode: 1. Press the AUTO button. When AUTO is selected, the display will change to show the current driver’s set temperature, delivery mode and fan speed. Press the AUTO button again within ﬁve seconds to display the passenger’s set temperature. If the driver’s and passenger’s temperature settings are the same when AUTO is pressed, the temperature setting and both arrows will be displayed for ﬁve seconds along with the automatic air delivery mode and fan speed. After the ﬁve-second update, the display will change to show the temperature setting, both arrows and AUTO. If the driver’s and passenger’s temperature settings are not the same, the opposite side temperature setting will be displayed for an additional ﬁve seconds. To make the passenger’s temperature the same as the driver’s press and hold the AUTO button for about four seconds. When auto is selected, the air conditioning operation and air inlet will be automatically controlled. The air conditioning compressor will run when the outside temperature is over about 40°F (4°C). The air inlet will normally be set to outside air. If it’s hot outside, the air inlet may automatically switch to recirculate inside air to help quickly cool down your vehicle. The light on the button will illuminate in recirculation. 2. Set the driver’s and passenger’s temperature. To ﬁnd your comfort setting, start with a 74°F (23°C) temperature setting and allow about 20 minutes for the system to regulate. Turn the driver’s or passenger’s side temperature knob to adjust the temperature setting as necessary. If you choose the temperature setting of 60°F (15°C) the system will remain at the maximum cooling setting. If you choose the temperature setting of 90°F (32°C) the system will remain at the maximum heat setting. Choosing either maximum setting will not cause the vehicle to heat or cool any faster. Be careful not to cover the sensor located on the top of the instrument panel near the windshield. This sensor regulates air temperature based on sun load, and also turns on your headlamps. 3-25 C (Mode): Press this button to manually change the direction of the airﬂow in your vehicle. Repeatedly press the button until the desired mode appears on the display. If you press the mode button to select an air delivery mode, the display will change to show you the selected air mode delivery. The display will then show the current status of the system. When the system is turned off, the display will go blank after displaying the current status of the system. H (Panel): This setting will deliver air to the instrument panel outlets. ) (Bi-Level): This setting will deliver warmer air to the ﬂoor and cooler air to the instrument panel outlets. 6 (Floor): This setting will deliver air to the ﬂoor outlets. - (Defog): See “Defogging and Defrosting” later in this section. To avoid blowing cold air in cold weather, the system will delay turning on the fan until warm air is available. The length of delay depends on the engine coolant temperature. Pressing the fan switch will override this delay and change the fan to a selected speed. 9(Off): Press this button to turn off the entire climate control system. Outside air will still enter the vehicle, and will be directed to the ﬂoor. This direction can be changed by pressing the mode button. The temperature can also be adjusted using either temperature knob. Press the up or down arrows on the fan switch, the defrost button, the AUTO button, or the air conditioning button to turn the system on when it is off. Manual Operation You may manually adjust the air delivery mode or fan speed. w9x (Fan): The switch with the fan symbol allows you to manually adjust the fan speed. Press the up arrow to increase fan speed and the down arrow to decrease fan speed. Pressing this button when the system is off will turn the system on. 3-26 @ (Recirculation): Press this button to limit the amount of outside air entering your vehicle. The light on the recirculation button will glow. This is helpful when you are trying to limit odors entering your vehicle and for maximum air conditioning performance in hot weather. Press this button again to allow outside air to enter the vehicle. The light on the recirculation button will go off. Pressing this button also cancels the auto recirculation feature. To resume the auto recirculation function, press the AUTO button. Each time the vehicle is started, the system will revert to the auto recirculation function. If you select recirculation while in defrost, defog or ﬂoor, the light in the button will ﬂash and then go out to let you know that this is not allowed. This is normal and helps to prevent fogging. When the weather is cool or damp, operating the system in recirculation for extended periods of time may cause fogging of the vehicle’s windows. To clear the fog, select either defog or front defrost. You may also notice that the A/C compressor will run while in recirculation mode. This is normal and helps to prevent fogging. # (Air Conditioning): Press this button to turn the air conditioning (A/C) compressor on and off. The snowﬂake symbol will appear on the display when the A/C is on and will turn off when the air conditioning is off. Pressing this button when the outside temperature is too cool for air conditioning to be effective will make the snowﬂake symbol ﬂash three times and then turn off to let you know that the air conditioning mode is not available. If the air conditioning is on and the outside temperature drops below a temperature which is too cool for air conditioning to be effective, the snowﬂake symbol will turn off to let you know that the air conditioning mode has been canceled. When air conditioning is selected or in AUTO mode, the system will run the air conditioning automatically to cool and dehumidify the air entering the vehicle. If you select A/C off while in front defrost, defog or recirculation, the A/C snowﬂake symbol will turn off, but the A/C compressor will still run to help prevent fogging. On hot days, open the windows long enough to let hot inside air escape. This reduces the time it takes for your vehicle to cool down. Then keep your windows closed for the air conditioner to work its best. 3-27 On cool, but sunny days while using manual operation of the automatic system, use bi-level to deliver warm air to the ﬂoor and cooler air to the instrument panel outlets. To warm or cool the air delivered, turn the temperature knob to the desired setting. In AUTO mode the system will cool and dehumidify the air inside the vehicle. Also while in AUTO mode, the system will maximize its performance by using recirculation as necessary. 9(Off): Press this button to turn off the entire climate control system. Outside air will still enter the vehicle, and will be directed to the ﬂoor. This direction can be changed by pressing the mode button. The temperature can also be adjusted using either temperature knob. Press the up or down arrows on the fan switch, the defrost button, the AUTO button, or the air conditioning button to turn the system on when it is off. Defogging and Defrosting You can use either defog or front defrost to clear fog or frost from your windshield. Use the defog mode to clear the windows of fog or moisture. Use the front defrost button to defrost the front windshield. - (Defog): Use this setting to clear the windows of fog or moisture. Press the mode button to select this setting. This setting will deliver air to the ﬂoor and windshield outlets. Recirculation is not available in this mode. 0 (Defrost): Press this button to defrost the windshield. The system will automatically control the fan speed if you select defrost from AUTO mode. If the outside temperature is 40°F (4°C) or warmer, your air conditioning compressor will automatically run to help dehumidify the air and dry the windshield. Recirculation is not available in this mode. 3-28 Rear Window Defogger The lines you see on the rear window warm the glass. The rear window defogger uses a warming grid to remove fog from the rear window. < (Rear): Press this button to turn the rear window defogger on or off. An indicator light in the button will come on to let you know that the rear window defogger is activated.

Boost Classifieds - Car Advice, Reviews, Events & Classifieds

2006 Cadillac Escalade Owners Manual