2009 Cadillac DTS Owners Manual

Download PDF Manual
for more information. 3-54 Passenger Airbag Status Indicator The vehicle has the passenger sensing system. See Passenger Sensing System on page 1-64 for important safety information. The overhead console has a passenger airbag status indicator. If the word ON or the on symbol is lit on the passenger airbag status indicator, it means that the right front passenger frontal airbag and seat-mounted side impact airbag are enabled (may inﬂate). If the word OFF or the off symbol is lit on the passenger airbag status indicator, it means that the passenger sensing system has turned off the right front passenger frontal and seat-mounted side impact airbag. If, after several seconds, both status indicator lights remain on, or if there are no lights at all, there may be a problem with the lights or the passenger sensing system. See your dealer/retailer for service. United States Canada When the vehicle is started, the passenger airbag status indicator will light ON and OFF, or the symbol for on and off, for several seconds as a system check. If you are using remote start to start the vehicle from a distance, if equipped, you may not see the system check. Then, after several more seconds, the status indicator will light either ON or OFF, or either the on or off symbol, to let you know the status of the right front passenger frontal and seat-mounted side impact airbags. { CAUTION: If the airbag readiness light ever comes on and stays on, it means that something may be wrong with the airbag system. To help avoid injury to yourself or others, have the vehicle serviced right away. See Airbag Readiness Light on page 3-54 for more information, including important safety information. 3-55 Charging System Light This light comes on brieﬂy when the ignition key is turned to START, but the engine is not running, as a check to show it is working. Brake System Warning Light The vehicle’s hydraulic brake system is divided into two parts. If one part is not working, the other part can still work and stop the vehicle. For good braking both parts need to be working. If the warning light comes on, there is a brake problem. Have the brake system inspected right away. If it does not, have the vehicle serviced by your dealer/retailer. The light should go out once the engine starts. If it stays on, or comes on while driving, there could be a problem with the charging system. A charging system message in the Driver Information Center (DIC) can also appear. See DIC Warnings and Messages on page 3-73 for more information. This light could indicate that there are problems with a generator drive belt, or that there is an electrical problem. Have it checked right away. If the vehicle must be driven a short distance with the light on, turn off accessories, such as the radio and air conditioner. 3-56 United States Canada This light comes on brieﬂy when the engine is turned on. If it does not come on then, have it ﬁxed so it will be ready to warn if there is a problem. When the ignition is on, the brake system warning light also comes on when the parking brake is set. The light will stay on if the parking brake does not release fully. If it stays on after the parking brake is fully released, it means there is a brake problem. If the light comes on while driving, pull off the road and stop carefully. The pedal may be harder to push, or the pedal may go closer to the ﬂoor. It may take longer to stop. If the light is still on, have the vehicle towed for service. See Towing Your Vehicle on page 4-26. { CAUTION: The brake system might not be working properly if the brake system warning light is on. Driving with the brake system warning light on can lead to a crash. If the light is still on after the vehicle has been pulled off the road and carefully stopped, have the vehicle towed for service. Antilock Brake System (ABS) Warning Light For vehicles with the Antilock Brake System (ABS), this light comes on brieﬂy when the engine is started. If it does not, have the vehicle serviced by your dealer/retailer. If the system is working normally the indicator light then goes off. If the ABS light stays on, turn the ignition off. If the light comes on while driving, stop as soon as it is safely possible and turn the ignition off. Then start the engine again to reset the system. If the ABS light stays on, or comes on again while driving, the vehicle needs service. If the regular brake system warning light is not on, the vehicle still has brakes, but not antilock brakes. If the regular brake system warning light is also on, the vehicle does not have antilock brakes and there is a problem with the regular brakes. See Brake System Warning Light on page 3-56. For vehicles with a Driver Information Center (DIC), see DIC Warnings and Messages on page 3-73 for all brake related DIC messages. 3-57 Traction Control System (TCS) Warning Light This warning light comes on brieﬂy while starting the engine. StabiliTrak® Indicator Light For vehicles with the StabiliTrak® system, this light comes on brieﬂy while starting the engine. If it does not, have the vehicle serviced by your dealer/retailer. If the system is working normally the indicator light will then go off. If it stays on, or comes on while driving, there may be a problem with the traction control system and the vehicle needs service. When this warning light is on, the system will not limit wheel spin. If the traction control system warning light comes on and stays on when the system is turned on, the vehicle needs service. See Traction Control System (TCS) on page 4-6 for more information. If it does not, have the vehicle serviced by your dealer/retailer. If the system is working normally the indicator light then goes off. If the light comes on and stays on while driving, there could be a problem with the StabiliTrak® system and the vehicle might need service. When this warning light is on, the StabiliTrak® system is off and does not limit wheel spin. The light ﬂashes if the system is active and is working to assist the driver with directional control of the vehicle in difficult driving conditions. See StabiliTrak® System on page 4-6 for more information. 3-58 Lane Departure Warning (LDW) Light For vehicles with the lane departure warning system, this light brieﬂy comes on amber, while starting the vehicle, to indicate that it is working. If it does not, have the vehicle serviced by your dealer/retailer. If the system is working normally the indicator light then goes off. When driving at speeds of 35 mph (56 km) or greater and LDW is turned on, a green warning symbol appears when the system has detected lane markings on at least one side of the vehicle. For more information see Lane Departure Warning (LDW) on page 2-49. When LDW is active, the amber warning symbol comes on and ﬂashes. Three beeps sound if a lane marking is crossed without using the turn signal. If the warning symbol is not on, LDW is not operating and will not warn when the vehicle crosses a lane marking. Engine Coolant Temperature Warning Light The engine coolant temperature warning light comes on when the engine is very hot. This light also comes on brieﬂy when the vehicle is started. If the light does not go out or comes on and stays on while driving, there may be a problem with the cooling system. Driving with engine coolant temperature light on could cause the vehicle to overheat, see Overheated Engine Protection Operating Mode on page 5-30. See Engine Overheating on page 5-28 and DIC Warnings and Messages on page 3-73 for more information. 3-59 Engine Coolant Temperature Gage Tire Pressure Light This gage shows the engine coolant temperature. For vehicles with a tire pressure monitoring system, this light comes on brieﬂy when the engine is started. It provides information about tire pressures and the Tire Pressure Monitoring System. It indicates when the engine has warmed up and if the cooling system is operating properly. If the gage pointer moves into the shaded area, the engine coolant is too hot and the engine coolant temperature warning light comes on. See Engine Overheating on page 5-28 for more information. 3-60 When the Light is On Steady This indicates that one or more of the tires is signiﬁcantly underinﬂated. A tire pressure message in the Driver Information Center (DIC), can accompany the light. See DIC Warnings and Messages on page 3-73 for more information. Stop and check the tires as soon as it is safe to do so. If a tire is underinﬂated, inﬂate to the proper pressure. See Tires on page 5-48 for more information. When the Light Flashes First and Then is On Steady This indicates that there could be a problem with the Tire Pressure Monitor System. The light ﬂashes for about a minute and stays on steady for the remainder of the ignition cycle. This sequence repeats with every ignition cycle. See Tire Pressure Monitor System on page 5-60 for more information. Malfunction Indicator Lamp Check Engine Light A computer system called OBD II (On-Board Diagnostics-Second Generation) monitors operation of the fuel, ignition, and emission control systems. It ensures that emissions are at acceptable levels for the life of the vehicle, helping to produce a cleaner environment. This light should come on when the ignition is on, but the engine is not running, as a check to show it is working. If it does not, have the vehicle serviced by your dealer/retailer. If the check engine light comes on and stays on, while the engine is running, this indicates that there is an OBD II problem and service is required. 3-61 Malfunctions often are indicated by the system before any problem is apparent. Being aware of the light can prevent more serious damage to the vehicle. This system assists the service technician in correctly diagnosing any malfunction. Notice: If the vehicle is continually driven with this light on, after a while, the emission controls might not work as well, the vehicle’s fuel economy might not be as good, and the engine might not run as smoothly. This could lead to costly repairs that might not be covered by the vehicle warranty. Notice: Modiﬁcations made to the engine, transmission, exhaust, intake, or fuel system of the vehicle or the replacement of the original tires with other than those of the same Tire Performance Criteria (TPC) can affect the vehicle’s emission controls and can cause this light to come on. Modiﬁcations to these systems could lead to costly repairs not covered by the vehicle warranty. This could also result in a failure to pass a required Emission Inspection/Maintenance test. See Accessories and Modiﬁcations on page 5-3. This light comes on during a malfunction in one of two ways: Light Flashing: A misﬁre condition has been detected. A misﬁre increases vehicle emissions and could damage the emission control system on the vehicle. Diagnosis and service might be required. To prevent more serious damage to the vehicle: (cid:129) Reduce vehicle speed. (cid:129) Avoid hard accelerations. (cid:129) Avoid steep uphill grades. If towing a trailer, reduce the amount of cargo being hauled as soon as it is possible. If the light continues to ﬂash, when it is safe to do so, stop the vehicle. Find a safe place to park the vehicle. Turn the key off, wait at least 10 seconds, and restart the engine. If the light is still ﬂashing, follow the previous steps and see your dealer/retailer for service as soon as possible. 3-62 (cid:129) Light On Steady: An emission control system malfunction has been detected on the vehicle. Diagnosis and service might be required. An emission system malfunction might be corrected by doing the following: (cid:129) Make sure the fuel cap is fully installed. See Filling the Tank on page 5-7. The diagnostic system can determine if the fuel cap has been left off or improperly installed. A loose or missing fuel cap allows fuel to evaporate into the atmosphere. A few driving trips with the cap properly installed should turn the light off. If the vehicle has been driven through a deep puddle of water, the vehicle’s electrical system might be wet. The condition is usually corrected when the electrical system dries out. A few driving trips should turn the light off. (cid:129) Make sure to fuel the vehicle with quality fuel. Poor fuel quality causes the engine not to run as efficiently as designed and can cause: stalling after start-up, stalling when the vehicle is changed into gear, misﬁring, hesitation on acceleration, or stumbling on acceleration. These conditions might go away once the engine is warmed up. If one or more of these conditions occurs, change the fuel brand used. It will require at least one full tank of the proper fuel to turn the light off. See Gasoline Octane on page 5-5. If none of the above have made the light turn off, your dealer/retailer can check the vehicle. The dealer/retailer has the proper test equipment and diagnostic tools to ﬁx any mechanical or electrical problems that might have developed. 3-63 (cid:129) Emissions Inspection and Maintenance Programs Some state/provincial and local governments have or might begin programs to inspect the emission control equipment on the vehicle. Failure to pass this inspection could prevent getting a vehicle registration. Here are some things to know to help the vehicle pass an inspection: The vehicle will not pass this inspection if the check engine light is on with the engine running, or if the key is in ON/RUN and the light is not on. The vehicle will not pass this inspection if the OBD II (on-board diagnostic) system determines that critical emission control systems have not been completely diagnosed by the system. The vehicle would be considered not ready for inspection. This can happen if the battery has recently been replaced or if the battery has run down. The diagnostic system is designed to evaluate critical emission control systems during normal driving. This can take several days of routine driving. If this has been done and the vehicle still does not pass the inspection for lack of OBD II system readiness, your dealer/retailer can prepare the vehicle for inspection. 3-64 Oil Pressure Light { CAUTION: Do not keep driving if the oil pressure is low. The engine can become so hot that it catches ﬁre. Someone could be burned. Check the oil as soon as possible and have the vehicle serviced. Notice: Lack of proper engine oil maintenance can damage the engine. The repairs would not be covered by the vehicle warranty. Always follow the maintenance schedule in this manual for changing engine oil. (cid:129) (cid:129) This light comes on brieﬂy while starting the engine. If it does not, have the vehicle serviced by your dealer/retailer. If the system is working normally the indicator light then goes off. If the light comes on and stays on, it means that oil is not ﬂowing through the engine properly. The vehicle could be low on oil and it might have some other system problem. Security Light Fog Lamp Light The fog lamp light comes on when the fog lamps are in use. For information regarding this light and the vehicle’s security system, see Content Theft-Deterrent on page 2-21. The light goes out when the fog lamps are turned off. See Fog Lamps on page 3-34 for more information. Lights On Reminder This light comes on whenever the parking lamps are on. See Exterior Lamps on page 3-29 for more information. 3-65 Cruise Control Light Fuel Gage This light comes on whenever the cruise control is set. The fuel gage shows approximately how much fuel is in the tank. It works only when the engine is on. The light goes out when the cruise control is turned off. See Cruise Control on page 3-16 and Adaptive Cruise Control on page 3-19 for more information. Highbeam On Light This light comes on when the high-beam headlamps are in use. An arrow on the fuel gage indicates the side of the vehicle the fuel door is on. If the fuel supply gets low, the FUEL LEVEL LOW message appears in the Driver Information Center and a single chime sounds. See DIC Warnings and Messages on page 3-73 for more information. See Headlamp High/Low-Beam Changer on page 3-9 for more information. 3-66 Here are a few situations that may occur with the fuel gage. All of these situations are normal and do not indicate that anything is wrong with the fuel gage: (cid:129) At the gas station the gas pump shuts off before the gage reads full. The gage may change when the vehicle is turning, stops quickly or accelerates quickly. It takes a little more or less fuel to ﬁll the tank than the gage indicated. For example, the gage may have indicated that the tank was half full, but it actually took a little more or less than half the tank’s capacity to ﬁll the tank. Driver Information Center (DIC) The Driver Information Center (DIC) gives you the status of many of your vehicle’s systems. The DIC is also used to display warning/status messages. All messages will appear in the DIC display located at the bottom of the instrument panel cluster, below the tachometer and speedometer. The DIC buttons are located on the instrument panel, to the left of the steering wheel. The DIC comes on when the ignition is on. After a short delay, the DIC will display the information that was last displayed before the engine was turned off. The top line of the DIC display shows the vehicle system information and the warning/status messages. The bottom line of the DIC display shows the odometer on the left side. The bottom line of the DIC display also shows a digital speedometer on the right side. If a problem is detected, a warning message will appear on the display. Be sure to take any message that appears on the display seriously and remember that clearing the message will only make the message disappear, not correct the problem. 3-67 (cid:129) (cid:129) DIC Operation and Displays The Driver Information Center (DIC) has different displays which can be accessed by pressing the DIC buttons located on the instrument panel, to the left of the steering wheel. 3 Trip/Fuel: Press this button to scroll through the trip and fuel displays. See “Trip/Fuel Display Menu Items” following for more information on these displays. T Vehicle Information: Press this button to scroll through the vehicle information displays. See “Vehicle Information Display Menu Items” following for more information on these displays. U Customization: Press this button to scroll through each of the customization features. See DIC Vehicle Customization on page 3-86 for more information on the customization features. V Set/Reset: Press this button to reset certain DIC features and to acknowledge DIC warning messages and clear them from the DIC display. y z Menu Up/Down: Press this button to scroll up and down the menu items. Trip/Fuel Display Menu Items 3 (Trip/Fuel): The following display menu items can be displayed by pressing the trip/fuel button: TRIP A or TRIP B These displays show the current distance traveled since the last reset for each trip odometer in either miles (mi) or kilometers (km). Both odometers can be used at the same time. Each trip odometer can be reset to zero separately by pressing and holding the set/reset button for a few seconds while the desired trip odometer is displayed. 3-68 FUEL RANGE This display shows the approximate number of remaining miles (mi) or kilometers (km) you can drive without reﬁlling the fuel tank. This estimate is based on the current driving conditions and will change if the driving conditions change. For example, if you are driving in traffic and making frequent stops, the display may read one number, but if you enter the freeway, the number may change even though you still have the same amount of fuel in the fuel tank. This is because different driving conditions produce different fuel economies. Generally, freeway driving produces better fuel economy than city driving. Once the range drops below an estimated 40 miles (64 km) remaining, the display will show FUEL RANGE LOW. If your vehicle is low on fuel, the FUEL LEVEL LOW message will be displayed. See “FUEL LEVEL LOW” under DIC Warnings and Messages on page 3-73 for more information. AVERAGE ECONOMY (AFE) This display shows the approximate average miles per gallon (mpg) or liters per 100 kilometers (L/100 km). This number is calculated based on the number of mpg (L/100 km) recorded since the last time this display was reset. To reset this display, press the set/reset button. The display will return to zero. INST (Instantaneous) ECONOMY (IFE) This display shows the current fuel economy in either miles per gallon (mpg) or liters per 100 kilometers (L/100 km). This number reﬂects only the fuel economy that the vehicle has right now and will change frequently as driving conditions change. Unlike average economy, this display cannot be reset. FUEL USED This display shows the number of gallons (gal) or liters (L) of fuel used since the last reset of this display. To reset this display, press the set/reset button. The display will return to zero. TIMER ON/OFF This display can be used like a stopwatch. You can record the time it takes to travel from one point to another. To access the timer, press the trip/fuel button until 00:00:00 TIMER OFF displays. To turn on the timer, press the set/reset button until TIMER ON displays. The timer will then start. To turn off the timer, press the set/reset button again until TIMER OFF displays. The timer will stop and display the end timing value. To reset the timer, press and hold the set/reset button after the timer has been stopped. The display will return to zero. 3-69 AVERAGE SPEED This display shows the average speed of the vehicle in either miles per hour (mph) or kilometers per hour (km/h). This average is calculated based on the various vehicle speeds recorded since the last reset of this display. To reset this display, press the set/reset button. The display will return to zero. BATTERY VOLTAGE This display shows the current battery voltage. If the voltage is in the normal range, the value will display. For example, the display may read BATTERY VOLTAGE 13.2 VOLTS. If the voltage is low, the display will show LOW. If the voltage is high, the display will show HIGH. Your vehicle’s charging system regulates voltage based on the state of the battery. The battery voltage may ﬂuctuate when viewing this information on the DIC. This is normal. See Charging System Light on page 3-56 for more information. If there is a problem with the battery charging system, the DIC will display a message. See DIC Warnings and Messages on page 3-73 and Electric Power Management on page 3-36 for more information. Blank Display This display shows no information. Vehicle Information Display Menu Items T (Vehicle Information): The following display menu items can be displayed by pressing the vehicle information button: OIL LIFE REMAINING If the vehicle has this display, it shows the estimated oil life remaining. If you see 99% OIL LIFE REMAINING on the display, that means that 99% of the current oil life remains. When the oil life is depleted, the CHANGE ENGINE OIL SOON message will appear on the display. You should change the oil as soon as possible. In addition to the engine oil life system monitoring the oil life, additional maintenance is recommended in the Maintenance Schedule in this manual. See Scheduled Maintenance on page 6-4 and Engine Oil on page 5-13. Remember, you must reset the OIL LIFE yourself after each oil change. It will not reset itself. Also, be careful not to reset the OIL LIFE accidentally at any time other than when the oil has just been changed. It cannot be reset accurately until the next oil change. To reset the engine oil life system, See Engine Oil Life System on page 5-16. The display will show 100% when the system is reset. 3-70 UNITS This display allows you to select between English or Metric units of measurement. Once in this display, press the set/reset button to select between ENGLISH or METRIC units. PARKING ASSIST If your vehicle has the Ultrasonic Front and Rear Parking Assist (UFRPA) system, this display allows the system to be turned on or off. Once in this display, press the set/reset button to select between ON or OFF. If you choose ON, the system will be turned on. If you choose OFF, the system will be turned off. The UFRPA system automatically turns back on after each vehicle start. When the UFRPA system is turned off and the vehicle is shifted out of P (Park), the DIC will display the PARKING ASSIST OFF message as a reminder that the system has been turned off. See DIC Warnings and Messages on page 3-73 and Ultrasonic Front and Rear Parking Assist (UFRPA) on page 2-42 for more information. SIDE BLIND ZONE ALERT If your vehicle has the Side Blind Zone Alert (SBZA) system, this display allows the system to be turned on or off. Once in this display, press the set/reset button to select between ON or OFF. If you choose ON, the system will be turned on. If you choose OFF, the system will be turned off. When the SBZA system is turned off, the DIC will display the SIDE BLIND ZONE ALERT SYSTEM OFF message as a reminder that the system has been turned off. See DIC Warnings and Messages on page 3-73 and Side Blind Zone Alert (SBZA) on page 2-45 for more information. FRONT TIRES or REAR TIRES On vehicles with the Tire Pressure Monitor System (TPMS), the pressure for each tire can be viewed in the DIC. The tire pressure will be shown in either pounds per square inch (psi) or kilopascals (kPa). Press the vehicle information button until the DIC displays FRONT TIRES PSI (kPa) LEFT ## RIGHT ##. Press the vehicle information button again until the DIC displays REAR TIRES PSI (kPa) LEFT ## RIGHT ##. If a low or high tire pressure condition is detected by the system while driving, a message advising you to check the pressure in a speciﬁc tire will appear in the display. See Inﬂation - Tire Pressure on page 5-57 and DIC Warnings and Messages on page 3-73 for more information. If the tire pressure display shows dashes instead of a value, there may be a problem with your vehicle. If this consistently occurs, see your dealer/retailer for service. 3-71 SPEED LIMIT: XXX MPH (SPEED LIMIT: XXX Km/h) or ADVISORY: XXX MPH (ADVISORY: XXX Km/h) This display will show the speed limit or the advised speed as determined by the information on the map disc in the navigation system. If there is no map disc in the navigation system, this display will not be available. The speed limit and speed advisory displays on the DIC are for reference only. There may be segments of road where speed data has not been captured or times where incorrect speed data, or no speed data, will be displayed by the DIC due to the navigation system not correctly matching the vehicle’s position to the actual road. Be aware of this and obey posted speed limits wherever you drive. SPEED ALERT This display will allow you to customize the speed alert warning. You can choose to have no warning display, or to have it display at the limit, at 5 mph (km/h) over the limit, or at 10 mph (km/h) over the limit. The DIC will toggle between OFF, AT LIMIT, +5, +10 (MPH or Km/h). Press the reset button to make your selection. 3-72 RELEARN REMOTE KEY This display allows you to match Remote Keyless Entry (RKE) transmitters to your vehicle. This procedure will erase all previously learned transmitters. Therefore, they must be relearned as additional transmitters. To match an RKE transmitter to your vehicle: 1. Press the vehicle information button until PRESS V TO RELEARN REMOTE KEY displays. 2. Press the set/reset button until REMOTE KEY LEARNING ACTIVE is displayed. 3. Press and hold the lock and unlock buttons on the ﬁrst transmitter at the same time for about 15 seconds. On vehicles with memory recall seats, the ﬁrst transmitter learned will match driver 1 and the second will match driver 2. A chime will sound indicating that the transmitter is matched. 4. To match additional transmitters at this time, repeat Step 3. Each vehicle can have a maximum of eight transmitters matched to it. 5. To exit the programming mode, you must cycle the key to LOCK/OFF. Blank Display This display shows no information. DIC Warnings and Messages These messages appear if there is a problem detected in one of your vehicle’s systems. You must acknowledge a message to clear it from the screen for further use. To clear a message, press the set/reset button. Be sure to take any message that appears on the screen seriously and remember that clearing the message will only make the message disappear, not the problem. ADVISORY XXX MPH (km/h) This message displays when the Speed Alert has been turned on through the DIC Information Menu and the vehicle is at or above the advised speed. See DIC Operation and Displays on page 3-68. AUTOMATIC LIGHT CONTROL OFF This message displays when the automatic headlamps are turned off. See Exterior Lamps on page 3-29 for more information. AUTOMATIC LIGHT CONTROL ON This message displays when the automatic headlamps are turned on. See Exterior Lamps on page 3-29 for more information. BATTERY SAVER ACTIVE This message displays when the system detects that the battery voltage is dropping beyond a reasonable level. The battery saver system starts reducing certain features of the vehicle that you may be able to notice. At the point that the features are disabled, this message is displayed. It means that the vehicle is trying to save the charge in the battery. Turn off all unnecessary accessories to allow the battery to recharge. The normal battery voltage range is 11.5 to 15.5 volts. You can monitor battery voltage on the Driver Information Center (DIC) by pressing the trip/fuel button until BATTERY VOLTAGE is displayed. CHANGE ENGINE OIL SOON This message displays when service is required for your vehicle. See your dealer/retailer. See Engine Oil on page 5-13 and Scheduled Maintenance on page 6-4 for more information. When you reset the CHANGE ENGINE OIL SOON message by clearing it from the display, you still must reset the engine oil life system separately. For more information on resetting the engine oil life system, see Engine Oil Life System on page 5-16. 3-73 CRUISE SET TO XXX MPH (km/h) This message displays whenever the cruise control is set. See Cruise Control on page 3-16 and Adaptive Cruise Control on page 3-19 for more information. If your vehicle has Adaptive Cruise Control (ACC), after a few seconds, this message clears and the message “SET SPD XX” displays at the bottom of the DIC. See “SET SPD (Speed)” later in this section. DRIVER DOOR OPEN This symbol appears with this message. This message displays when the driver door is not closed completely. Make sure that the door is closed completely. CHECK TIRE PRESSURE On vehicles with the Tire Pressure Monitor System (TPMS), this message displays when the pressure in one or more of the vehicle’s tires needs to be checked. This message also displays LEFT FRONT, RIGHT FRONT, LEFT REAR, or RIGHT REAR to indicate which tire needs to be checked. You can receive more than one tire pressure message at a time. To read the other messages that may have been sent at the same time, press the set/reset button. If a tire pressure message appears on the DIC, stop as soon as you can. Have the tire pressures checked and set to those shown on the Tire Loading Information label. See Tires on page 5-48, Loading the Vehicle on page 4-19, and Inﬂation - Tire Pressure on page 5-57. The DIC also shows the tire pressure values. See DIC Operation and Displays on page 3-68. If the tire pressure is low, the low tire pressure warning light comes on. See Tire Pressure Light on page 3-60. CLEAN RADAR This message displays when the Adaptive Cruise Control (ACC) system and the Forward Collision Alert (FCA) system are disabled because the radar is blocked and cannot detect vehicles in your path. It may also activate during heavy rain or due to road spray. To clean the system, see “Cleaning the System” under Adaptive Cruise Control on page 3-19. 3-74 ENGINE HOT – A/C (Air Conditioning) OFF This message displays when the engine coolant becomes hotter than the normal operating temperature. See Engine Coolant Temperature Gage on page 3-60. To avoid added strain on a hot engine, the air conditioning compressor automatically turns off. When the coolant temperature returns to normal, the air conditioning compressor turns back on. You can continue to drive your vehicle. If this message continues to appear, have the system repaired by your dealer/retailer as soon as possible to avoid damage to the engine. ENGINE OVERHEATED IDLE ENGINE Notice: If you drive your vehicle while the engine is overheating, severe engine damage may occur. If an overheat warning appears on the instrument panel cluster and/or DIC, stop the vehicle as soon as possible. Do not increase the engine speed above normal idling speed. See Engine Overheating on page 5-28 for more information. This message displays when the engine coolant temperature is too hot. Stop and allow the vehicle to idle until it cools down. See Engine Coolant Temperature Warning Light on page 3-59. See Overheated Engine Protection Operating Mode on page 5-30 for information on driving to a safe place in an emergency. ENGINE OVERHEATED STOP ENGINE Notice: If you drive your vehicle while the engine is overheating, severe engine damage may occur. If an overheat warning appears on the instrument panel cluster and/or DIC, stop the vehicle as soon as possible. See Engine Overheating on page 5-28 for more information. This message displays when the engine has overheated. Immediately look for a safe place to pull your vehicle over and turn the engine off right away to avoid severe engine damage. See Engine Overheating on page 5-28 and Overheated Engine Protection Operating Mode on page 5-30. A chime also sounds when this message is displayed. 3-75 ENGINE POWER REDUCED This message displays when the engine power is being reduced to protect the engine from damage. There could be several malfunctions that might cause this message. Reduced engine power can affect the vehicle’s ability to accelerate. If this message is on, but there is no reduction in performance, proceed to your destination. The performance may be reduced the next time the vehicle is driven. The vehicle may be driven at a reduced speed while this message is on, but acceleration and speed may be reduced. Anytime this message stays on, the vehicle should be taken to your dealer/retailer for service as soon as possible. FOLLOWING GAP If your vehicle has Adaptive Cruise Control (ACC), this message displays to show the follow distance that has been set. There are six follow distances to choose from. Each follow distance is shown on the DIC by displaying from one to six bars between two car symbols. See Adaptive Cruise Control on page 3-19 for more information. FUEL LEVEL LOW This symbol appears with this message. This message displays when your vehicle is low on fuel. Reﬁll the fuel tank as soon as possible. A single chime sounds when this message is displayed. See Filling the Tank on page 5-7. This symbol appears with this message. 3-76 HEATED WASHER FLUID SYSTEM OFF This message displays when you manually turn off the heated washer ﬂuid system or when the system automatically turns off. See “Heated Washer Fluid” under Windshield Washer on page 3-15 for more information. HEATING WASH (Washer) FLUID WASH (Washer) WIPES PENDING This message displays when you turn on the heated washer ﬂuid system. See “Heated Washer Fluid” under Windshield Washer on page 3-15 for more information. HOOD OPEN ICE POSSIBLE DRIVE WITH CARE This message displays when the outside temperature is cold enough to create icy road conditions. Adjust your driving accordingly. LANE DEPARTURE SYSTEM UNAVAILABLE If your vehicle has the Lane Departure Warning (LDW) system, this message may display if the LDW system does not activate due to a temporary condition. See Lane Departure Warning (LDW) on page 2-49 for more information. LEFT REAR DOOR OPEN This symbol appears with this message. This symbol appears with this message. This message displays when the hood is not closed completely. Make sure that the hood is closed completely. See Hood Release on page 5-11. This message displays when the driver side rear door is not closed completely. Make sure that the door is closed completely. 3-77 If you drive your vehicle while the engine NO CRUISE BRAKING GAS PEDAL APPLIED This message displays when the Adaptive Cruise Control (ACC) is engaged and you are pressing the accelerator pedal enough to disable ACC automatic braking. See Adaptive Cruise Control on page 3-19 for more information. OIL PRESSURE LOW STOP ENGINE Notice: oil pressure is low, severe engine damage may occur. If a low oil pressure warning appears on the instrument panel cluster and/or DIC, stop the vehicle as soon as possible. Do not drive the vehicle until the cause of the low oil pressure is corrected. See Engine Oil on page 5-13 for more information. This message displays when the vehicle’s engine oil pressure is low. The oil pressure light also appears on the instrument panel cluster. See Oil Pressure Light on page 3-64. A multiple chime sounds when this message is displayed. See Engine Oil on page 5-13 for more information. Stop the vehicle immediately, as engine damage can result from driving a vehicle with low oil pressure. Have the vehicle serviced by your dealer/retailer as soon as possible when this message is displayed. 3-78 PARKING ASSIST OFF If your vehicle has the Ultrasonic Front and Rear Parking Assist (UFRPA) system, after the vehicle is shifted out of P (Park), this message displays to remind the driver that the UFRPA system has been turned off. Press the set/reset button to acknowledge this message and clear it from the DIC display. To turn the UFRPA system back on, see “PARKING ASSIST” under DIC Operation and Displays on page 3-68. See Ultrasonic Front and Rear Parking Assist (UFRPA) on page 2-42 for more information. PASSENGER DOOR OPEN This symbol appears with this message. This message displays when the passenger side front door is not closed completely. Make sure that the door is closed completely. RADAR CRUISE NOT READY This message displays when the Adaptive Cruise Control (ACC) system will not activate due to a temporary condition. Your vehicle does not require service. If this message appears when you attempt to activate the system, continue driving for several minutes and then try activating the system again. See Adaptive Cruise Control on page 3-19 for more information. RAINSENSE WIPERS ACTIVE If your vehicle has Rainsense™ II wipers, this message displays while this feature is active. See Rainsense™ II Wipers on page 3-14 for more information. REMOTE KEY LEARNING ACTIVE This message displays while you are matching a Remote Keyless Entry (RKE) transmitter to your vehicle. See “Matching Transmitter(s) to Your Vehicle” under Remote Keyless Entry (RKE) System Operation on page 2-5 and DIC Operation and Displays on page 3-68 for more information. REPLACE BATTERY IN REMOTE KEY This message displays when the battery in the Remote Keyless Entry (RKE) transmitter needs to be replaced. To replace the battery, see “Battery Replacement” under Remote Keyless Entry (RKE) System Operation on page 2-5. RIGHT REAR DOOR OPEN This symbol appears with this message. This message displays when the passenger side rear door is not closed completely. Make sure that the door is closed completely. SERVICE AIR BAG This message displays when there is a problem with the airbag system. Have your vehicle serviced by your dealer/retailer immediately. See Airbag Readiness Light on page 3-54 for more information. 3-79 SERVICE A/C SYSTEM This message displays when the air delivery mode door or the electronic sensors that control the air conditioning and heating systems are no longer working. Have the climate control system serviced by your dealer/retailer if you notice a drop in heating and air conditioning efficiency. SERVICE BATTERY CHARGING SYSTEM This message displays when a problem with the charging system has been detected. The charging system light also displays on the instrument panel cluster. See Charging System Light on page 3-56 for more information. Have your vehicle serviced by your dealer/retailer. SERVICE BRAKE ASSIST This message displays if there is a problem with the brake system. The brake system warning light and the antilock brake system warning light may also be displayed on the instrument panel cluster. See Brake System Warning Light on page 3-56 and Antilock Brake System (ABS) Warning Light on page 3-57 for more information. If this happens, stop as soon as possible and turn off the vehicle. Restart the vehicle and check for the message on the DIC display. If the message is displayed or appears again when you begin driving, the brake system needs service. See your dealer/retailer as soon as possible. See Brakes on page 5-33 for more information. SERVICE BRAKE SYSTEM This message displays if the ignition is on to inform the driver that the brake ﬂuid level is low. Have the brake system serviced by your dealer/retailer as soon as possible. SERVICE LANE DEPARTURE SYSTEM If your vehicle has the Lane Departure Warning (LDW) system, this message may display to indicate that the LDW system is not working properly. If this message remains on after continued driving, the system needs service. See your dealer/retailer. See Lane Departure Warning (LDW) on page 2-49 for more information. 3-80 SERVICE PARKING ASSIST If your vehicle has the Ultrasonic Front and Rear Parking Assist (UFRPA) system, this message displays if there is a problem with the UFRPA system. Do not use this system to help you park. See Ultrasonic Front and Rear Parking Assist (UFRPA) on page 2-42 for more information. See your dealer/retailer for service. SERVICE POWER STEERING Your vehicle may have a speed variable assist steering system. See Steering on page 4-8. This message displays if a problem is detected with the speed variable assist steering system. When this message is displayed, you may notice that the effort required to steer the vehicle decreases or feels lighter, but you will still be able to steer the vehicle. SERVICE RADAR CRUISE This message displays when the Adaptive Cruise Control (ACC) system and the Forward Collision Alert (FCA) system are disabled and need service. See your dealer/retailer. SERVICE SIDE BLIND ZONE ALERT SYSTEM If your vehicle has the Side Blind Zone Alert (SBZA) system and this message displays, both SBZA displays will remain on indicating there is a problem with the SBZA system. If these displays remain on after continued driving, the system needs service. See your dealer/ retailer. See Side Blind Zone Alert (SBZA) on page 2-45 for more information. SERVICE STABILITRAK Your vehicle may have a vehicle stability enhancement system called StabiliTrak®. See StabiliTrak® System on page 4-6. This message displays if there has been a problem detected with the StabiliTrak system. If this message comes on while you are driving, pull off the road as soon as possible and stop carefully. Try resetting the system by turning the ignition off then back on. If this message still stays on or comes back on again while you are driving, your vehicle needs service. Have the StabiliTrak system inspected by your dealer/ retailer as soon as possible. 3-81 SERVICE SUSPENSION SYS (System) This message displays when the magnetic ride control or automatic leveling control system is not operating properly. Have your vehicle serviced by your dealer/retailer. SERVICE THEFT DETERRENT SYSTEM This message displays when there is a problem with the theft-deterrent system programmed in the key. A fault has been detected in the system which means that the system is disabled and it is not protecting the vehicle. The vehicle usually restarts; however, you may want to take the vehicle to your dealer/retailer before turning off the engine. See PASS-Key® III+ Electronic Immobilizer Operation on page 2-23 for more information. SERVICE TIRE MONITOR SYSTEM On vehicles with the Tire Pressure Monitor System (TPMS), this message displays if a part on the TPMS is not working properly. The tire pressure light also ﬂashes and then remains on during the same ignition cycle. See Tire Pressure Light on page 3-60. Several conditions may cause this message to appear. See Tire Pressure Monitor Operation on page 5-61 for more information. If the warning comes on and stays on, there may be a problem with the TPMS, see your dealer/retailer. 3-82 SERVICE TRACTION CONTROL This message displays when there is a problem with the Traction Control System (TCS). When this message is displayed, the system will not limit wheel spin. Adjust your driving accordingly. See your dealer/retailer for service. See Traction Control System (TCS) on page 4-6 for more information. SERVICE TRANSMISSION This message displays when there is a problem with the vehicle’s transmission. Have your vehicle serviced by your dealer/retailer. SERVICE VEHICLE SOON This message displays when a non-emissions related malfunction occurs. Have your vehicle serviced by your dealer/retailer as soon as possible. SET SPD (Speed) If your vehicle has Adaptive Cruise Control (ACC), this message displays whenever the cruise control is set. First, the “CRUISE SET TO XXX MPH (km/h)” message appears. After a few seconds, the “CRUISE SET TO XXX MPH (km/h)” message clears and the message “SET SPD XX” displays at the bottom of the DIC. See “CRUISE SET TO XXX MPH (km/h)” earlier in this section and Adaptive Cruise Control on page 3-19 for more information. SIDE BLIND ZONE ALERT SYSTEM OFF If your vehicle has the Side Blind Zone Alert (SBZA) system, this message displays when the SBZA system has been turned off. See Side Blind Zone Alert (SBZA) on page 2-45 and DIC Operation and Displays on page 3-68 for more information. SIDE BLIND ZONE SYSTEM UNAVAILABLE If your vehicle has the Side Blind Zone Alert (SBZA) system, this message displays when the SBZA system is disabled because the sensor is blocked and cannot detect vehicles in your blind zone. The sensor may be blocked by mud, dirt, snow, ice, or slush. This message may also display during heavy rain or due to road spray. It may also come on when driving in isolated areas with no guardrails, trees, or road signs and light traffic. Your vehicle does not need service. For cleaning instructions, see Washing Your Vehicle on page 5-90. See Side Blind Zone Alert (SBZA) on page 2-45 for more information. SPEED LIMIT XXX MPH (km/h) This message displays when the Speed Alert has been turned on through the DIC Information Menu and the vehicle is at or above the speed limit. See DIC Operation and Displays on page 3-68 for more information. SPEED LIMITED TO XXX MPH (km/h) This message displays when your vehicle speed is limited to 80 mph (128 km/h) because the vehicle detects a problem in the speed variable assist steering, magnetic ride control, or automatic leveling control systems. Have your vehicle serviced by your dealer/retailer. STABILITRAK NOT READY If your vehicle has StabiliTrak, this message may display and the Traction Control System and StabiliTrak Warning Light on the instrument panel cluster may be on after ﬁrst driving the vehicle and exceeding 19 mph (30 km/h) for 30 seconds. The StabiliTrak system is not functional until the light has turned off. See StabiliTrak® System on page 4-6 for more information. 3-83 TIRE LEARNING ACTIVE This message displays when the Tire Pressure Monitor System (TPMS) is re-learning the tire positions on your vehicle. The tire positions must be re-learned after rotating the tires or after replacing a tire or sensor. See Tire Inspection and Rotation on page 5-65, Tire Pressure Monitor System on page 5-60, and Inﬂation - Tire Pressure on page 5-57 for more information. TRACTION CONTROL OFF This message displays when the Traction Control System (TCS) is turned off. Adjust your driving accordingly. See Traction Control System (TCS) on page 4-6 for more information. TRACTION CONTROL ON This message displays when the Traction Control System (TCS) is turned on. See Traction Control System (TCS) on page 4-6 for more information. STARTING DISABLED SERVICE THROTTLE This message displays when your vehicle’s throttle system is not functioning properly. Have your vehicle serviced by your dealer/retailer. THEFT ATTEMPTED This symbol appears with this message. This message displays if the content theft-deterrent system has detected a break-in attempt while you were away from your vehicle. See Content Theft-Deterrent on page 2-21 for more information. TIGHTEN GAS CAP This message displays when the fuel cap has not been fully tightened. Recheck the fuel cap to ensure that it is on and tightened properly. 3-84 If you drive your vehicle while the TRANSMISSION HOT IDLE ENGINE Notice: transmission ﬂuid is overheating and the transmission temperature warning is displayed on the instrument panel cluster and/or DIC, you can damage the transmission. This could lead to costly repairs that would not be covered by your warranty. Do not drive your vehicle with overheated transmission ﬂuid or while the transmission temperature warning is displayed. This message displays when the transmission ﬂuid in your vehicle is too hot. Stop the vehicle and allow it to idle until the transmission cools down or until this message is removed. TRUNK OPEN TURN SIGNAL ON This message displays as a reminder to turn off the turn signal if you drive your vehicle for more than about 1 mile (1.6 km) with a turn signal on. A multiple chime sounds when this message is displayed. WASHER FLUID LOW ADD FLUID This symbol appears with this message. This symbol appears with this message. This message displays when your vehicle is low on windshield washer ﬂuid. Reﬁll the windshield washer ﬂuid reservoir as soon as possible. See Windshield Washer Fluid on page 5-32 for more information. This message displays when the trunk is not closed completely. Make sure that the trunk is closed completely. 3-85 DIC Vehicle Customization Your vehicle has customization capabilities that allow you to program certain features to one preferred setting. Customization features can only be programmed to one setting on the vehicle and cannot be programmed to a preferred setting for two different drivers. All of the customization options may not be available on your vehicle. Only the options available will be displayed on the DIC. The default settings for the customization features were set when your vehicle left the factory, but may have been changed from their default state since then. The customization preferences are automatically recalled. To change customization preferences, use the following procedure. Entering the Feature Settings Menu 1. Turn the ignition on and place the vehicle in P (Park). To avoid excessive drain on the battery, it is recommended that the headlamps are turned off. 2. Press the customization button to enter the feature settings menu. If the menu is not available, FEATURE SETTINGS AVAILABLE IN PARK will display. Before entering the menu, make sure the vehicle is in P (Park). Feature Settings Menu Items The following are customization features that allow you to program settings to the vehicle: DISPLAY IN ENGLISH This feature will only display if a language other than English has been set. This feature allows you to change the language in which the DIC messages appear to English. Press the customization button until the PRESS V TO DISPLAY IN ENGLISH screen appears on the DIC display. Press the set/reset button once to display all DIC messages in English. 3-86 DISPLAY LANGUAGE This feature allows you to select the language in which the DIC messages will appear. Press the customization button until the DISPLAY LANGUAGE screen appears on the DIC display. Press the set/reset button once to access the settings for this feature. Then press the menu up/down button to scroll through the following settings: ENGLISH (default): All messages will appear in English. DEUTSCH: All messages will appear in German. FRANCAIS: All messages will appear in French. ESPANOL: All messages will appear in Spanish. JAPANESE: All messages will appear in Japanese. ARABIC: All messages will appear in Arabic. NO CHANGE: No change will be made to this feature. The current setting will remain. To select a setting, press the set/reset button while the desired setting is displayed on the DIC. AUTO DOOR LOCK This feature allows you to select when the vehicle’s doors will automatically lock. See Programmable Automatic Door Locks on page 2-11 for more information. Press the customization button until AUTO DOOR LOCK appears on the DIC display. Press the set/reset button once to access the settings for this feature. Then press the menu up/down button to scroll through the following settings: SHIFT OUT OF PARK (default): The doors automatically lock when the doors are closed and the vehicle is shifted out of P (Park). AT VEHICLE SPEED: The doors automatically lock when the vehicle speed is above 5 mph (8 km/h) for three seconds. NO CHANGE: No change will be made to this feature. The current setting will remain. To select a setting, press the set/reset button while the desired setting is displayed on the DIC. 3-87 AUTO DOOR UNLOCK This feature allows you to select whether or not to turn off the automatic door unlocking feature. It also allows you to select which doors and when the doors will automatically unlock. See Programmable Automatic Door Locks on page 2-11 for more information. Press the customization button until AUTO DOOR UNLOCK appears on the DIC display. Press the set/reset button once to access the settings for this feature. Then press the menu up/down button to scroll through the following settings: OFF: None of the doors will automatically unlock. DRIVER AT KEY OUT: Only the driver’s door will unlock when the key is taken out of the ignition. DRIVER IN PARK: Only the driver’s door will unlock when the vehicle is shifted into P (Park). ALL AT KEY OUT: All of the doors will unlock when the key is taken out of the ignition. ALL IN PARK (default): All of the doors will unlock when the vehicle is shifted into P (Park). NO CHANGE: No change will be made to this feature. The current setting will remain. To select a setting, press the set/reset button while the desired setting is displayed on the DIC. 3-88 REMOTE DOOR LOCK This feature allows you to select the type of feedback you will receive when locking the vehicle with the Remote Keyless Entry (RKE) transmitter. You will not receive feedback when locking the vehicle with the RKE transmitter if the doors are open. See Remote Keyless Entry (RKE) System Operation on page 2-5 for more information. Press the customization button until REMOTE DOOR LOCK appears on the DIC display. Press the set/reset button once to access the settings for this feature. Then press the menu up/down button to scroll through the following settings: OFF: There will be no feedback when you press the lock button on the RKE transmitter. LIGHTS ONLY: The exterior lamps will ﬂash when you press the lock button on the RKE transmitter. HORN ONLY: The horn will sound on the second press of the lock button on the RKE transmitter. HORN & LIGHTS (default): The exterior lamps will ﬂash when you press the lock button on the RKE transmitter, and the horn will sound when the lock button is pressed again within ﬁve seconds of the previous command. NO CHANGE: No change will be made to this feature. The current setting will remain. To select a setting, press the set/reset button while the desired setting is displayed on the DIC. REMOTE DOOR UNLOCK This feature allows you to select the type of feedback you will receive when unlocking the vehicle with the Remote Keyless Entry (RKE) transmitter. You will not receive feedback when unlocking the vehicle with the RKE transmitter if the doors are open. See Remote Keyless Entry (RKE) System Operation on page 2-5 for more information. Press the customization button until REMOTE DOOR UNLOCK appears on the DIC display. Press the set/reset button once to access the settings for this feature. Then press the menu up/down button to scroll through the following settings: LIGHTS OFF: The exterior lamps will not ﬂash when you press the unlock button on the RKE transmitter. LIGHTS ON (default): The exterior lamps will ﬂash when you press the unlock button on the RKE transmitter. NO CHANGE: No change will be made to this feature. The current setting will remain. To select a setting, press the set/reset button while the desired setting is displayed on the DIC. DELAY DOOR LOCK This feature allows you to select whether or not the locking of the vehicle’s doors will be delayed. When locking the doors with the power door lock switch and a door is open, this feature will delay locking the doors until ﬁve seconds after the last door is closed. You will hear three chimes to signal that the delayed locking feature is in use. The key must be out of the ignition for this feature to work. You can temporarily override delayed locking by pressing the power door lock switch twice or the lock button on the RKE transmitter twice. Press the customization button until DELAY DOOR LOCK appears on the DIC display. Press the set/reset button once to access the settings for this feature. Then press the menu up/down button to scroll through the following settings: OFF: There will be no delayed locking of the vehicle’s doors. ON (default): The doors will not lock until ﬁve seconds after the last door is closed. NO CHANGE: No change will be made to this feature. The current setting will remain. To select a setting, press the set/reset button while the desired setting is displayed on the DIC. 3-89 EXIT LIGHTING This feature allows you to select the amount of time you want the exterior lamps to remain on when it is dark enough outside. This happens after the key is turned from ON/RUN to LOCK/OFF. Press the customization button until EXIT LIGHTING appears on the DIC display. Press the set/reset button once to access the settings for this feature. Then press the menu up/down button to scroll through the following settings: OFF: The exterior lamps will not turn on. 30 SECONDS (default): The exterior lamps will stay on for 30 seconds. 1 MINUTE: The exterior lamps will stay on for one minute. 2 MINUTES: The exterior lamps will stay on for two minutes. NO CHANGE: No change will be made to this feature. The current setting will remain. To select a setting, press the set/reset button while the desired setting is displayed on the DIC. APPROACH LIGHTING This feature allows you to select whether or not to have the exterior lights turn on brieﬂy during low light periods after unlocking the vehicle using the Remote Keyless Entry (RKE) transmitter. Press the customization button until APPROACH LIGHTING appears on the DIC display. Press the set/reset button once to access the settings for this feature. Then press the menu up/down button to scroll through the following settings: OFF: The exterior lights will not turn on when you unlock the vehicle with the RKE transmitter. ON (default): If it is dark enough outside, the exterior lights will turn on brieﬂy when you unlock the vehicle with the RKE transmitter. The lights will remain on for 20 seconds or until the lock button on the RKE transmitter is pressed, or the vehicle is no longer off. See Remote Keyless Entry (RKE) System Operation on page 2-5 for more information. NO CHANGE: No change will be made to this feature. The current setting will remain. To select a setting, press the set/reset button while the desired setting is displayed on the DIC. 3-90 CHIME VOLUME This feature allows you to select the volume level of the chime. Press the customization button until CHIME VOLUME appears on the DIC display. Press the set/reset button once to access the settings for this feature. Then press the menu up/down button to scroll through the following settings: NORMAL: The chime volume will be set to a normal level. LOUD: The chime volume will be set to a loud level. NO CHANGE: No change will be made to this feature. The current setting will remain. There is no default for chime volume. The volume will stay at the last known setting. To select a setting, press the set/reset button while the desired setting is displayed on the DIC. PARK TILT MIRRORS If your vehicle has this feature, it allows you to select whether or not the outside mirror(s) will automatically tilt down when the vehicle is shifted into R (Reverse). See Park Tilt Mirrors on page 2-41 for more information. Press the customization button until PARK TILT MIRRORS appears on the DIC display. Press the set/reset button once to access the settings for this feature. Then press the menu up/down button to scroll through the following settings: OFF (default): Neither outside mirror will be tilted down when the vehicle is shifted into R (Reverse). DRIVER MIRROR: The driver’s outside mirror will be tilted down when the vehicle is shifted into R (Reverse). PASSENGER MIRROR: The passenger’s outside mirror will be tilted down when the vehicle is shifted into R (Reverse). BOTH MIRRORS: The driver’s and passenger’s outside mirrors will be tilted down when the vehicle is shifted into R (Reverse). NO CHANGE: No change will be made to this feature. The current setting will remain. To select a setting, press the set/reset button while the desired setting is displayed on the DIC. 3-91 EASY EXIT RECALL If your vehicle has this feature, it allows you to select your preference for the automatic easy exit seat feature. See Memory Seat, Mirrors and Steering Wheel on page 1-6 for more information. Press the customization button until EASY EXIT RECALL appears on the DIC display. Press the set/reset button once to access the settings for this feature. Then press the menu up/down button to scroll through the following settings: DOOR BUTTON ONLY: No automatic seat exit recall will occur. The recall will only occur after pressing the easy exit seat button. BUTTON AND KEY OUT (default): If the features are enabled through the EASY EXIT SETUP menu, the driver’s seat will move back, and if the vehicle has the power tilt wheel and telescopic steering feature, the power steering column will move up and forward when the key is removed from the ignition or after pressing the easy exit seat button. The automatic easy exit seat movement will only occur one time after the key is removed from the ignition. If the automatic movement has already occurred, and you put the key back in the ignition and remove it again, the seat and steering column will stay in the original exit position, unless a memory recall took place prior to removing the key again. 3-92 NO CHANGE: No change will be made to this feature. The current setting will remain. To select a setting, press the set/reset button while the desired setting is displayed on the DIC. EASY EXIT SETUP If your vehicle has this feature, it allows you to select which areas will recall with the automatic easy exit seat feature. It also allows you to turn off the automatic easy exit feature. See Memory Seat, Mirrors and Steering Wheel on page 1-6 and “EASY EXIT RECALL” earlier for more information. Press the customization button until EASY EXIT SETUP appears on the DIC display. Press the set/reset button once to access the settings for this feature. Then press the menu up/down button to scroll through the following settings: OFF: No automatic seat exit will recall. SEAT ONLY: The driver’s seat will recall. TILT ONLY: The steering wheel tilt feature will recall. TELESCOPE ONLY: The steering column telescope feature will recall. SEAT/TILT: The driver’s seat and the steering wheel tilt feature will recall. SEAT/TELESCOPE: The driver’s seat and the steering column telescope feature will recall. TILT/TELESCOPE: The steering wheel tilt and steering column telescope features will recall. ALL (default): The driver’s seat and the steering wheel tilt and steering column telescope features will recall, if your vehicle has this option. NO CHANGE: No change will be made to this feature. The current setting will remain. To select a setting, press the set/reset button while the desired setting is displayed on the DIC. MEMORY SEAT RECALL If your vehicle has this feature, it allows you to select your preference for the remote memory seat recall feature. See Memory Seat, Mirrors and Steering Wheel on page 1-6 for more information. Press the customization button until MEMORY SEAT RECALL appears on the DIC display. Press the set/reset button once to access the settings for this feature. Then press the menu up/down button to scroll through the following settings: OFF (default): No remote memory seat recall will occur. ON: The driver’s seat and outside mirrors will automatically move to the stored driving position when the unlock button on the Remote Keyless Entry (RKE) transmitter is pressed. The steering column will also move on vehicles with the power tilt and telescopic steering feature. See Power Tilt Wheel and Telescopic Steering Column on page 3-7 for more information. See “RELEARN REMOTE KEY” under DIC Operation and Displays on page 3-68 for more information on matching transmitters to driver ID numbers. NO CHANGE: No change will be made to this feature. The current setting will remain. To select a setting, press the set/reset button while the desired setting is displayed on the DIC. 3-93 REMOTE START If your vehicle has this feature, it allows you to turn the remote start off or on. The remote start feature allows you to start the engine from outside of the vehicle using the Remote Keyless Entry (RKE) transmitter. See Remote Vehicle Start on page 2-7 for more information. Press the customization button until REMOTE START appears on the DIC display. Press the set/reset button once to access the settings for this feature. Then press the menu up/down button to scroll through the following settings: OFF: The remote start feature will be disabled. ON (default): The remote start feature will be enabled. NO CHANGE: No change will be made to this feature. The current setting will remain. To select a setting, press the set/reset button while the desired setting is displayed on the DIC. 3-94 FACTORY SETTINGS This feature allows you to set all of the customization features back to their factory default settings. Press the customization button until FACTORY SETTINGS appears on the DIC display. Press the set/reset button once to access the settings for this feature. Then press the menu up/down button to scroll through the following settings: RESTORE ALL (default): The customization features will be set to their factory default settings. DO NOT RESTORE: The customization features will not be set to their factory default settings. To select a setting, press the set/reset button while the desired setting is displayed on the DIC. Exiting the Feature Settings Menu The feature settings menu will be exited when any of the following occurs: The vehicle is shifted out of P (Park). The vehicle is no longer in ON/RUN. The trip/fuel or vehicle information DIC buttons are pressed. The end of the feature settings menu is reached and exited. (cid:129) A 40 second time period has elapsed with no selection made. (cid:129) (cid:129) (cid:129) (cid:129) Audio System(s) Determine which radio the vehicle has and read the following pages to become familiar with its features. { CAUTION: Taking your eyes off the road for extended periods could cause a crash resulting in injury or death to you or others. Do not give extended attention to entertainment tasks while driving. This system provides access to many audio and non audio listings. To minimize taking your eyes off the road while driving, do the following while the vehicle is parked: (cid:129) Become familiar with the operation and controls of the audio system. (cid:129) Set up the tone, speaker adjustments, and preset radio stations. For more information, see Defensive Driving on page 4-2. Notice: Contact your dealer/retailer before adding any equipment. Adding audio or communication equipment could interfere with the operation of the vehicle’s engine, radio, or other systems, and could damage them. Follow federal rules covering mobile radio and telephone equipment. The vehicle has Retained Accessory Power (RAP). With RAP, the audio system can be played even after the ignition is turned off. See Retained Accessory Power (RAP) on page 2-26 for more information. 3-95 Setting the Clock Radio with a Single CD or a Six-Disc CD Player The vehicle has an analog clock as well as the digital radio clock. At the time of new vehicle delivery, the digital radio clock display should be disabled. If you decide to use the digital radio clock as well as the analog clock, you can change the setting to enable the radio clock display. Enabling/Disabling the Digital Radio Clock For the Single CD Player To turn the radio clock display on or off: 1. Turn the radio on. 2. Press the H button until the clock and date setting menus appear. 3. Press the pushbutton located under the forward arrow tab until the menu for default clock and date settings appear. 4. Press the pushbutton located under the currently displayed status of either ON or OFF. The ON display indicates the radio clock display is disabled and the OFF display indicates the radio clock display is enabled. Press this pushbutton to toggle the radio clock display on or off. If the radio clock display is turned on, the screen displays Radio Clock ON for 10 seconds, then returns to the original clock display menu. If the radio clock display is turned off, the screen displays Radio Clock OFF for 10 seconds. The menus for clock and date settings are removed, and ON displays as a current status indicating that the clock display can be turned on, if desired. The radio clock and analog clock are not synchronized. Occasionally you might need to set the digital radio clock using the procedure below to synchronize both clocks. 3-96 For a Six-Disc CD Player To turn the radio clock display on or off: 1. Turn the radio on. 2. Press the MENU button until H is displayed 3. Press the pushbutton located under H until the clock and date settings appear. 4. Press the pushbutton located under the forward arrow tab until the menu for default clock and date settings appear. 5. Press the pushbutton located under the currently displayed status of either ON or OFF. The ON display indicates the radio clock display is disabled and the OFF display indicates the radio clock display is enabled. Press this pushbutton to toggle the radio clock display on or off. If the radio clock display is turned on, the screen displays Radio Clock ON for 10 seconds, then returns to the original clock display menu. If the radio clock display is turned off, the screen displays Radio Clock OFF for 10 seconds. The menus for clock and date settings are removed, and ON displays as a current status indicating that the clock display can be turned on, if desired. Setting the Time and Date For the Single CD Player This type of radio has a H button for setting the time and date. To set the time and date: 1. Turn the radio on. 2. Press H and HR, MIN, MM, DD, YYYY (hour, minute, month, day, and year) displays. 3. Press the pushbutton located under any one of the tabs that you want to change. Every time the pushbutton is pressed again, the time or the date if selected, increases by one. (cid:129) Another way to increase the time or date, is to press the right SEEK arrow or the \ FWD button. To decrease the time or date, press the left SEEK arrow or the s REV button. You can also turn the a knob, located on the upper right side of the radio faceplate, to adjust the selected setting. 3-97 (cid:129) For a Six-Disc CD Player This type of radio has a MENU button for setting the time and date. To set the time and date: 1. Turn the radio on. 2. Press the MENU button until H option is displayed. 3. Press the pushbutton located under H and the HR, MIN, MM, DD, YYYY (hour, minute, month, day, and year) displays. 4. Press the pushbutton located under any one of the tabs that you want to change. Every time the pushbutton is pressed again, the time or the date if selected, increases by one. (cid:129) Another way to increase the time or date, is to press the right SEEK arrow or the \ FWD button. To decrease the time or date, press the left SEEK arrow or the s REV button. You can also turn the a knob, located on the upper right side of the radio faceplate, to adjust the selected setting. Changing the Time and Date Default Setting For the Single CD Player To change the time and date default setting: 1. Change the time default setting from 12 hour to 24 hour or the date default setting from month/day/ year to day/month/year, by pressing the H button. 2. Once the clock and date settings display along with the forward arrow tab, press the pushbutton located under the forward arrow tab until the time 12H and 24H, and the date MM/DD/YYYY (month, day, and year) and DD/MM/YYYY (day, month, and year) displays. 3. Press the pushbutton located under the desired option, then press the H button again to apply the selected default, or let the screen time out. 3-98 (cid:129) For the Six-Disc CD Player To change the time and date default setting: 1. Change the time default setting from 12 hour to 24 hour or the date default setting from month/day/ year to day/month/year, by pressing the MENU button. 2. Once H displays, press the pushbutton located under H until the time and date settings display along with a forward arrow. 3. Press the pushbutton located under the forward arrow tab until the time 12H and 24H, and the date MM/DD/YYYY (month, day, and year) and DD/MM/YYYY (day, month, and year) displays. 4. Press the pushbutton located under the desired option, then press the MENU button again to apply the selected default, or let the screen time out. Radio(s) (MP3) Radio with CD shown, Radio with Six-Disc CD similar Radio Data System (RDS) The audio system has RDS. The RDS feature is available for use only on FM stations that broadcast RDS information. This system relies upon receiving speciﬁc information from these stations and only works when the information is available. While the radio is tuned to an FM-RDS station, the station name or call letters display. In rare cases, a radio station can broadcast incorrect information that causes the radio features to work improperly. If this happens, contact the radio station. 3-99 AudioPilot®: If the vehicle has the Bose® audio system, it has AudioPilot noise compensation technology. To use AudioPilot: 1. Set the radio volume to the desired level. 2. Press the MENU button to display the radio setup menu. 3. Press the pushbutton located under the AUTO VOLUM tab on the radio display. 4. Press the ON or OFF button to turn this feature on or off. When turned ON, AudioPilot continuously adjusts the audio system equalization, to compensate for background noise, so that the music always sounds the same at the set volume level. The feature is most effective at lower radio volume settings where background noise can affect how well you hear the music being played through the vehicle’s audio system. At high volume settings there might be little or no adjustments by AudioPilot. For more information on AudioPilot, visit bose.com/audiopilot. Playing the Radio O (Power/Volume): Press to turn the system on and off. Turn to increase or decrease the volume. Speed Compensated Volume (SCV): Radios with SCV automatically adjusts the radio volume to compensate for road and wind noise while driving. That way, the volume level should sound about the same while driving. To activate SCV: 1. Set the radio volume to the desired level. 2. Press the MENU button to display the radio setup menu. 3. Press the pushbutton under the AUTO VOLUM (automatic volume) tab on the radio display. 4. Press the pushbutton under the desired Speed Compensated Volume setting (OFF, Low, Med, or High) to select the level of radio volume compensation. The display times out after approximately 10 seconds. Each higher setting allows for more radio volume compensation at faster vehicle speeds. 3-100 Finding a Station BAND: Press to switch between AM, FM, or XM™. The selection displays. a (Tune): Turn to select radio stations. ©SEEK ¨: Press the arrows to go to the next or to the previous station and stay there. To scan stations, press and hold either arrow for three seconds until a beep sounds. The radio goes to a station, plays for a few seconds, then goes to the next station. Press either arrow again to stop scanning. The radio only seeks and scans stations with a strong signal that are in the selected band. 4 (Information) (XM™ Satellite Radio Service, MP3/WMA, and RDS Features): Press this button to display additional text information related to the current FM-RDS or XM station, or MP3/WMA song. A choice of additional information such as: Channel, Song, Artist, CAT (category) can display. Continue pressing the information button to highlight the desired label, or press the pushbutton positioned under any one of the tabs and the information about that tab displays. When information is not available, No Info displays. Storing a Radio Station as a Favorite Drivers are encouraged to set up their radio station favorites while the vehicle is in P (Park). Tune to favorite stations using the presets, favorites button, and steering wheel controls, if the vehicle has this feature. See Defensive Driving on page 4-2. FAV (Favorites): A maximum of 36 stations can be programmed as favorites using the six pushbuttons positioned below the radio station frequency tabs and by using the radio favorites page button. Press the FAV button to go through up to six pages of favorites, each having six favorite stations available per page. Each page of favorites can contain any combination of AM, FM, or XM stations. To store a station as a favorite: 1. Tune to the desired radio station. 2. Press the FAV button to display the page where you want the station stored. 3. Press and hold one of the six pushbuttons until a beep sounds. When that pushbutton is pressed and released, the station that was set, returns. 4. Repeat the steps for each pushbutton radio station you want stored as a favorite. 3-101 The number of favorites pages can be setup using the MENU button. To setup the number of favorites pages: 1. Press the MENU button to display the radio setup menu. 2. Press the pushbutton located below the FAV 1-6 label. 3. Select the desired number of favorites pages by pressing the pushbutton located below the displayed page numbers. 4. Press the FAV button, or let the menu time out, to return to the original main radio screen showing the radio station frequency labels and to begin the process of programming your favorites for the chosen amount of numbered pages. Setting the Tone (Bass/Midrange/Treble) BASS/MID/TREB (Bass, Midrange, or Treble): To adjust bass, midrange, or treble, press the a knob until the tone control labels display. Continue pressing to highlight the desired label, or press the pushbutton positioned under the desired label. Turn the a knob to adjust the highlighted setting. The highlighted setting can also be adjusted by pressing either SEEK arrow, \ FWD, or s REV button until the desired levels are obtained. If a station’s frequency is weak or has static, decrease the treble. To quickly adjust bass, midrange, or treble to the middle position, press the pushbutton positioned under the BASS, MID, or TREB label for more than two seconds. A beep sounds and the level adjusts to the middle position. To quickly adjust all tone and speaker controls to the middle position, press the a knob for more than two seconds until a beep sounds. 3-102 Adjusting the Speakers (Balance/Fade) BAL/FADE (Balance/Fade): To adjust balance or fade, press the a knob until the speaker control labels display. Continue pressing to highlight the desired label, or press the pushbutton positioned under the desired label. Turn the a knob to adjust the highlighted setting. The highlighted setting can be adjusted by pressing either SEEK arrow, \ FWD, or s REV buttons until the desired levels are obtained. To quickly adjust balance or fade to the middle position, press the pushbutton positioned under the BAL or FADE label for more than two seconds. A beep sounds and the level adjusts to the middle position. To quickly adjust all speaker and tone controls to the middle position, press the a knob for more than two seconds until a beep sounds. EQ (Equalization): For the non-Bose® ampliﬁed radio, perform the following steps to setup the equalization settings: 1. Press the a knob until the equalization label displays. 2. Press the pushbutton located under the equalization label to get choices of POP, ROCK, CTRY (country), TALK, JAZZ, and CLAS (classical), to display. 3. Press the pushbutton located under the desired setting. For the Bose ampliﬁed radio, perform the following steps to setup the equalization settings: 1. Press the a knob until the DSP label displays. 2. Press the pushbutton located under the DSP label to get choices of Norm, Driv, Rear, and Surround, to display. 3. Press the pushbutton located under the desired setting. To select Surround, press either the fourth or ﬁfth pushbutton located under the displayed Surround until Centerpoint displays. To return to the manual mode, press the tune knob. Select either BASS, MID, or TREB and start to manually adjust the settings by turning the a knob. 3-103 Digital Signal Processing (DSP) This feature is used to provide a choice of four different listening experiences. DSP can be used while listening to the audio system or a CD. To change the DSP mode, press the a knob until the DSP control label displays. Press the pushbutton located under the DSP label until the control labels display. Continue by pressing the desired button below the control labels on the display. For more information on the control label displays, see the following: (cid:129) Norm (Normal): Select this screen button to adjust the audio for normal mode. This provides the best sound quality for all seating positions. (cid:129) Driv (Driver): Select this screen button to adjust the audio for the driver to receive the best possible sound quality. (cid:129) Rear: Select this screen button to adjust the audio for the rear seat passengers to receive the best possible sound quality. (cid:129) Surround (Centerpoint®): Select this screen button to enable Bose® Centerpoint signal processing circuitry. Centerpoint produces a full vehicle surround sound listening experience from a CD, MP3/WMA, or XM stereo digital audio source and delivers ﬁve independent audio channels from conventional two channel stereo recordings. (Not available for AM, FM, or auxiliary sources.) 3-104 DSP is only available on vehicles that have the Bose Premium audio system. Finding a Category (CAT) Station CAT (Category): The CAT button is used to ﬁnd XM stations while the radio is in the XM mode. To ﬁnd XM channels within a desired category, perform the following: 1. Press the BAND button until the XM frequency displays. Press the CAT button to display the category tabs. Continue pressing the CAT button until the desired category name displays. Another way to select a category is to press the s REV or \ FWD button until the desired category is selected. 2. Press either of the two pushbuttons below the desired category tab to immediately tune to the ﬁrst XM station associated with that category. 3. Turn the a knob, press the pushbuttons below the displayed right or left arrows, or press either SEEK arrow to go to the previous or the next XM station within the selected category. 4. To exit the category search mode, press the FAV button or BAND button to display your favorites again. Undesired XM categories can be removed through the setup menu. To remove an undesired category: 1. Press the MENU button to display the radio setup menu. 2. Press the pushbutton located below the XM CAT tab. 3. Turn the a knob to display the category to be removed. 4. Press the pushbutton located under the Remove tab until the category name along with the word Removed displays. 5. Repeat the steps to remove more categories. Removed categories can be restored by pressing the pushbutton under the Add label when a removed category is displayed or by pressing the pushbutton under the Restore All label. The radio does not let you remove or add categories while the vehicle is moving faster than 5 mph (8 km/h). The CAT button also toggles between compressed and uncompressed audio when a mixed disc is present. See “Compressed Audio” later in this section. Radio Message Locked: This message displays when the THEFTLOCK® system has locked up the radio. Take the vehicle to your dealer/retailer for service. If any error occurs repeatedly or if an error cannot be corrected, contact your dealer/retailer. XM™ Satellite Radio Service XM is a satellite radio service that is based in the 48 contiguous United States and 10 Canadian provinces. XM Satellite Radio has a wide variety of programming and commercial-free music, coast-to-coast, and in digital-quality sound. During your trial or when you subscribe, you will get unlimited access to XM Radio Online for when you are not in the vehicle. A service fee is required to receive the XM service. For more information, contact XM at xmradio.com or call 1-800-929-2100 in the U.S. and xmradio.ca or call 1-877-438-9677 in Canada. Radio Messages for XM™ Only See XM Radio Messages on page 3-115 later in this section for further detail. 3-105 Playing a CD (Single CD Player) Insert a CD partway into the slot, label side up. The player pulls it in and the CD should begin playing. If the ignition or radio is turned off with a CD in the player, it stays in the player. When the ignition or radio is turned on, the CD starts playing where it stopped, if it was the last selected audio source. When a CD is inserted, the CD symbol displays. As each new track starts to play the track number displays. Care of CDs If playing a CD-R, the sound quality can be reduced due to CD-R quality, the method of recording, the quality of the music that has been recorded, and the way the CD-R has been handled. Handle them carefully. Store CD-R(s) in their original cases or other protective cases and away from direct sunlight and dust. The CD player scans the bottom surface of the disc. If the surface of a CD is damaged, such as cracked, broken, or scratched, the CD does not play properly or not at all. Do not touch the bottom side of a CD while handling it; this could damage the surface. Pick up CDs by grasping the outer edges or the edge of the hole and the outer edge. If the surface of a CD is soiled, take a soft, lint free cloth or dampen a clean, soft cloth in a mild, neutral detergent solution mixed with water, and clean it. Make sure the wiping process starts from the center to the edge. Care of The CD Player Do not add any label to a CD, it could get caught in the CD player. If a CD is recorded on a personal computer and a description label is needed, try labeling the top of the recorded CD with a marking pen. The use of CD lens cleaners for CDs is not advised, due to the risk of contaminating the lens of the CD optics with lubricants internal to the CD player mechanism. Notice: If a label is added to a CD, or more than one CD is inserted into the slot at a time, or an attempt is made to play scratched or damaged CDs,

Boost Classifieds - Car Advice, Reviews, Events & Classifieds

2009 Cadillac DTS Owners Manual