Download PDF Manual

(Continued)


the vehicle, such as the fuel system, brake and steering systems, etc. Even if the vehicle appears to be drivable after a moderate crash, there may be concealed damage that could make it difficult to safely operate the vehicle. Use caution if you should attempt to restart the engine after a crash has occurred.


In many crashes severe enough to inflate the airbag, windshields are broken by vehicle deformation. Additional windshield breakage may also occur from the front outboard passenger airbag. . Airbags are designed to inflate


only once. After an airbag inflates, you will need some new parts for the airbag system. If you do not get them, the airbag system will not be there


Buick LaCrosse Owner Manual - 2013 - 1st crc - 4/18/12


Black plate (26,1)


3-26


Seats and Restraints


Passenger Sensing System The vehicle has a passenger sensing system for the front outboard passenger position. The passenger airbag status indicator will light on the instrument panel when the vehicle is started.


The words ON and OFF will be visible during the system check. If you use remote start, if equipped, to start the vehicle from a distance you may not see the system check. When the system check is complete, either the word ON or the word OFF will be visible. See Passenger Airbag Status Indicator on page 5‑15.


The passenger sensing system turns off the front outboard passenger frontal airbag under certain conditions. No other airbag is affected by the passenger sensing system. The passenger sensing system works with sensors that are part of the front outboard passenger seat. The sensors are designed to detect the presence of a properly-seated occupant and determine if the front outboard passenger frontal airbag should be allowed to inflate or not. According to accident statistics, children are safer when properly secured in a rear seat in the correct child restraint for their weight and size. We recommend that children be secured in a rear seat, including: an infant or a child riding in a rear-facing child restraint; a child riding in a forward-facing child seat; an older child riding in a booster seat; and children, who are large enough, using safety belts.


Never put a rear-facing child seat in the front. This is because the risk to the rear-facing child is so great, if the airbag inflates.


{ WARNING


A child in a rear-facing child restraint can be seriously injured or killed if the passenger frontal airbag inflates. This is because the back of the rear-facing child restraint would be very close to the inflating airbag. A child in a forward-facing child restraint can be seriously injured or killed if the passenger frontal airbag inflates and the passenger seat is in a forward position. Even if the passenger sensing system has turned off the passenger frontal airbag, no system is fail-safe. No one can guarantee that an airbag will not


(Continued)


Buick LaCrosse Owner Manual - 2013 - 1st crc - 4/18/12


Black plate (27,1)


WARNING (CONTINUED)


inflate under some unusual circumstance, even though the airbag is off. Secure rear-facing child restraints in a rear seat, even if the airbag is off. If you secure a forward-facing child restraint in the front outboard passenger seat, always move the seat as far back as it will go. It is better to secure the child restraint in a rear seat.


The passenger sensing system is designed to turn off the front outboard passenger frontal airbag if:


The front outboard passenger seat is unoccupied. The system determines that an infant is present in a child restraint.


. A front outboard passenger


takes his/her weight off of the seat for a period of time. There is a critical problem with the airbag system or the passenger sensing system.


When the passenger sensing system has turned off the front outboard passenger frontal airbag, the off indicator will light and stay lit as a reminder that the airbag is off. See Passenger Airbag Status Indicator on page 5‑15. The passenger sensing system is designed to turn on the front outboard passenger frontal airbag anytime the system senses that a person of adult size is sitting properly in the front outboard passenger seat. When the passenger sensing system has allowed the airbag to be enabled, the on indicator will light and stay lit as a reminder that the airbag is active.


Seats and Restraints


3-27


For some children, including children in child restraints and for very small adults, the passenger sensing system may or may not turn off the front outboard passenger frontal airbag, depending upon the person's seating posture and body build. Everyone in the vehicle who has outgrown child restraints should wear a safety belt properly — whether or not there is an airbag for that person.


{ WARNING


If the airbag readiness light ever comes on and stays on, it means that something may be wrong with the airbag system. To help avoid injury to yourself or others, have the vehicle serviced right away. See Airbag Readiness Light on page 5‑14 for more information, including important safety information.


Buick LaCrosse Owner Manual - 2013 - 1st crc - 4/18/12


Black plate (28,1)


3-28


Seats and Restraints


If the On Indicator Is Lit for a Child Restraint If a child restraint has been installed and the on indicator is lit: 1. Turn the vehicle off. 2. Remove the child restraint from


the vehicle.


3. Remove any additional items


from the seat such as blankets, cushions, seat covers, seat heaters, or seat massagers.


4. Reinstall the child restraint


following the directions provided by the child restraint manufacturer and refer to Securing Child Restraints (Rear Seat) on page 3‑47 or Securing Child Restraints (Front Passenger Seat) on page 3‑49.


5.


If, after reinstalling the child restraint and restarting the vehicle, the on indicator is still lit, turn the vehicle off. Then slightly recline the vehicle seatback and adjust the seat cushion, if adjustable, to make sure that the vehicle seatback is not pushing the child restraint into the seat cushion. Also make sure the child restraint is not trapped under the vehicle head restraint. If this happens, adjust the head restraint. See Head Restraints on page 3‑2.


6. Restart the vehicle. The passenger sensing system may or may not turn off the airbag for a child in a child restraint depending upon the child's seating posture and body build. It is better to secure the child restraint in a rear seat.


If the Off Indicator Is Lit for an Adult-Size Occupant


If a person of adult-size is sitting in the front outboard passenger seat, but the off indicator is lit, it could be because that person is not sitting properly in the seat. Use the following steps to allow the system to detect that person and enable the front outboard passenger frontal airbag : 1. Turn the vehicle off.


Buick LaCrosse Owner Manual - 2013 - 1st crc - 4/18/12


Black plate (29,1)


Seats and Restraints


3-29


2. Remove any additional material from the seat, such as blankets, cushions, seat covers, seat heaters, seat massagers, a laptop, or other electronic devices.


3. Place the seatback in the fully


upright position.


4. Have the person sit upright in the seat, centered on the seat cushion, with legs comfortably extended.


5. Restart the vehicle and have the person remain in this position for two to three minutes after the on indicator is lit.


Additional Factors Affecting System Operation Safety belts help keep the passenger in position on the seat during vehicle maneuvers and braking, which helps the passenger sensing system maintain the passenger airbag status. See “Safety Belts” and “Child Restraints”


in the Index for additional information about the importance of proper restraint use. A thick layer of additional material, such as a blanket or cushion, or aftermarket equipment such as seat covers, seat heaters, and seat massagers can affect how well the passenger sensing system operates. We recommend that you not use seat covers or other aftermarket equipment except when approved by GM for your specific vehicle. See Adding Equipment to the Airbag-Equipped Vehicle on page 3‑30 for more information about modifications that can affect how the system operates. A wet seat can affect the performance of the passenger sensing system. Here is how:


The passenger sensing system may turn off the passenger frontal airbag when liquid is soaked into the seat. If this happens, the off indicator will be


lit, and the airbag readiness light on the instrument panel will also be lit. Liquid pooled on the seat that has not soaked in may make it more likely that the passenger sensing system will turn on the passenger frontal airbag while a child restraint or child occupant is on the seat. If the passenger frontal airbag is turned on, the on indicator will be lit.


If the passenger seat gets wet, dry the seat immediately. If the airbag readiness light is lit, do not install a child restraint or allow anyone to occupy the seat. See Airbag Readiness Light on page 5‑14 for important safety information. The on indicator may be lit if an object, such as a briefcase, handbag, grocery bag, laptop or other electronic device, is put on an unoccupied seat. If this is not desired remove the object from the seat.


Buick LaCrosse Owner Manual - 2013 - 1st crc - 4/18/12


Black plate (30,1)


3-30


Seats and Restraints


{ WARNING


{ WARNING


Stowing of articles under the passenger seat or between the passenger seat cushion and seatback may interfere with the proper operation of the passenger sensing system.


Servicing the Airbag-Equipped Vehicle Airbags affect how the vehicle should be serviced. There are parts of the airbag system in several places around the vehicle. Your dealer and the service manual have information about servicing the vehicle and the airbag system. To purchase a service manual, see Service Publications Ordering Information on page 13‑16.


For up to 10 seconds after the vehicle is turned off and the battery is disconnected, an airbag can still inflate during improper service. You can be injured if you are close to an airbag when it inflates. Avoid yellow connectors. They are probably part of the airbag system. Be sure to follow proper service procedures, and make sure the person performing work for you is qualified to do so.


Adding Equipment to the Airbag-Equipped Vehicle Adding accessories that change the vehicle's frame, bumper system, height, front end, or side sheet metal, may keep the airbag system from working properly. The operation of the airbag system can also be affected by changing or moving any parts of the front seats, safety belts, the airbag sensing and


diagnostic module, steering wheel, instrument panel, roof-rail airbag modules, ceiling headliner or pillar garnish trim, front sensors, side impact sensors, or airbag wiring. Your dealer and the service manual have information about the location of the airbag sensors, sensing and diagnostic module, and airbag wiring. In addition, the vehicle has a passenger sensing system for the front outboard passenger position, which includes sensors that are part of the passenger seat. The passenger sensing system may not operate properly if the original seat trim is replaced with non-GM covers, upholstery, or trim; or with GM covers, upholstery, or trim designed for a different vehicle. Any object, such as an aftermarket seat heater or a comfort‐enhancing pad or device, installed under or on top of the seat fabric, could also interfere with the operation of the passenger sensing system. This could either prevent proper


Buick LaCrosse Owner Manual - 2013 - 1st crc - 4/18/12


Black plate (31,1)


Seats and Restraints


3-31


deployment of the passenger airbag(s) or prevent the passenger sensing system from properly turning off the passenger airbag(s). See Passenger Sensing System on page 3‑26. If your vehicle needs to be modified because you have a disability and you have questions about whether the modifications will affect the vehicle's airbag system, or if you have questions about whether the airbag system will be affected if the vehicle is modified for any other reason, call Customer Assistance. See Customer Assistance Offices (U.S. and Canada) on page 13‑4 or Customer Assistance Offices (Mexico) on page 13‑5.


Airbag System Check The airbag system does not need regularly scheduled maintenance or replacement. Make sure the airbag readiness light is working. See Airbag Readiness Light on page 5‑14.


Notice: If an airbag covering is damaged, opened, or broken, the airbag may not work properly. Do not open or break the airbag coverings. If there are any opened or broken airbag covers, have the airbag covering and/or airbag module replaced. For the location of the airbags, see Where Are the Airbags? on page 3‑21. See your dealer for service.


Replacing Airbag System Parts after a Crash { WARNING


A crash can damage the airbag systems in the vehicle. A damaged airbag system may not work properly and may not protect you and your passenger(s) in a crash, resulting in serious injury or even death. To help make sure the airbag


(Continued)


WARNING (CONTINUED)


systems are working properly after a crash, have them inspected and any necessary replacements made as soon as possible.


If an airbag inflates, you will need to replace airbag system parts. See your dealer for service. If the airbag readiness light stays on after the vehicle is started or comes on when you are driving, the airbag system may not work properly. Have the vehicle serviced right away. See Airbag Readiness Light on page 5‑14 for more information. Vehicles with eAssist have a high voltage battery and a standard 12‐ volt battery. If an airbag inflates or the vehicle has been in a crash, the vehicle's sensing system may shut down the high voltage system. When this occurs, the high voltage battery is disconnected and the


Buick LaCrosse Owner Manual - 2013 - 1st crc - 4/18/12


Black plate (32,1)


Child Restraints


Older Children


3-32


Seats and Restraints


vehicle is not charging the 12‐volt battery or the electrical system. The vehicle may start but it shuts down once the 12‐volt battery is depleted. When the 12‐volt battery is depleted, the vehicle will not start and the on‐board jump start feature is disabled. The airbag readiness light and/or the 12‐volt battery warning light are displayed. Before the vehicle can be operated again, it must be serviced at your dealer.


Older children who have outgrown booster seats should wear the vehicle's safety belts.


The manufacturer's instructions that come with the booster seat, state the weight and height limitations for that booster. Use a booster seat with a lap-shoulder belt until the child passes the below fit test: . Sit all the way back on the seat.


Do the knees bend at the seat edge? If yes, continue. If no, return to the booster seat.


. Buckle the lap-shoulder belt.


Does the shoulder belt rest on the shoulder? If yes, continue. If no, then return to the booster seat.


. Does the lap belt fit low and


snug on the hips, touching the thighs? If yes, continue. If no, return to the booster seat.


. Can proper safety belt fit be


maintained for the length of the trip? If yes, continue. If no, return to the booster seat.


Buick LaCrosse Owner Manual - 2013 - 1st crc - 4/18/12


Black plate (33,1)


Seats and Restraints


3-33


thrown out of the vehicle. Older children need to use safety belts properly.


{ WARNING


Never allow more than one child to wear the same safety belt. The safety belt cannot properly spread the impact forces. In a crash, they can be crushed together and seriously injured. A safety belt must be used by only one person at a time.


Q: What is the proper way to


wear safety belts?


A: An older child should wear a lap-shoulder belt and get the additional restraint a shoulder belt can provide. The shoulder belt should not cross the face or neck. The lap belt should fit snugly below the hips, just touching the top of the thighs. This applies belt force to the child's pelvic bones in a crash. It should never be worn over the abdomen, which could cause severe or even fatal internal injuries in a crash.


According to accident statistics, children and infants are safer when properly restrained in a child restraint system or infant restraint system secured in a rear seating position. In a crash, children who are not buckled up can strike other people who are buckled up, or can be


{ WARNING


Never allow a child to wear the safety belt with the shoulder belt behind their back. A child can be seriously injured by not wearing the lap-shoulder belt properly. In a crash, the child would not be restrained by the shoulder belt. The child could move too far forward increasing the chance of head and neck injury. The child might also slide under the lap


(Continued)


Buick LaCrosse Owner Manual - 2013 - 1st crc - 4/18/12


Black plate (34,1)


3-34


Seats and Restraints


WARNING (CONTINUED)


belt. The belt force would then be applied right on the abdomen. That could cause serious or fatal injuries. The shoulder belt should go over the shoulder and across the chest.


Infants and Young Children Everyone in a vehicle needs protection! This includes infants and all other children. Neither the distance traveled nor the age and size of the traveler changes the need, for everyone, to use safety restraints. In fact, the law in every state in the United States and in every Canadian province says children up to some age must be restrained while in a vehicle. { WARNING


Children can be seriously injured or strangled if a shoulder belt is wrapped around their neck and the safety belt continues to tighten. Never leave children unattended in a vehicle and never allow children to play with the safety belts.


Airbags plus lap-shoulder belts offer protection for adults and older children, but not for young children and infants. Neither the vehicle's safety belt system nor its airbag system is designed for them. Every time infants and young children ride in vehicles, they should have the protection provided by appropriate child restraints. Children who are not restrained properly can strike other people, or can be thrown out of the vehicle.


{ WARNING


Never hold an infant or a child while riding in a vehicle. Due to crash forces, an infant or a child will become so heavy it is not possible to hold it during a crash. For example, in a crash at only 40 km/h (25 mph), a 5.5 kg (12 lb) infant will suddenly become a 110 kg (240 lb) force on a person's (Continued)


Buick LaCrosse Owner Manual - 2013 - 1st crc - 4/18/12


Black plate (35,1)


WARNING (CONTINUED)


WARNING (CONTINUED)


arms. An infant should be secured in an appropriate restraint.


child restraint in the right front seat. Secure a rear-facing child restraint in a rear seat. It is also better to secure a forward-facing child restraint in a rear seat. If you must secure a forward-facing child restraint in the right front seat, always move the front passenger seat as far back as it will go.


{ WARNING


Children who are up against, or very close to, any airbag when it inflates can be seriously injured or killed. Never put a rear-facing


(Continued)


Seats and Restraints


3-35


Q: What are the different types of


add-on child restraints?


A: Add-on child restraints, which are purchased by the vehicle owner, are available in four basic types. Selection of a particular restraint should take into consideration not only the child's weight, height, and age but also whether or not the restraint will be compatible with the motor vehicle in which it will be used. For most basic types of child restraints, there are many different models available. When purchasing a child restraint, be sure it is designed to be used in a motor vehicle. If it is, the restraint will have a label saying that it meets federal motor vehicle safety standards. The restraint manufacturer instructions that come with the restraint state the weight and height limitations for a particular child restraint. In addition, there


Buick LaCrosse Owner Manual - 2013 - 1st crc - 4/18/12


Black plate (36,1)


3-36


Seats and Restraints


are many kinds of restraints available for children with special needs.


{ WARNING


To reduce the risk of neck and head injury during a crash, infants need complete support. In a crash, if an infant is in a rear-facing child restraint, the crash forces can be distributed across the strongest part of an infant's body, the back and shoulders. Infants should always be secured in rear-facing child restraints.


{ WARNING


A young child's hip bones are still so small that the vehicle's regular safety belt may not remain low on the hip bones, as it should.


(Continued)


WARNING (CONTINUED)


Instead, it may settle up around the child's abdomen. In a crash, the belt would apply force on a body area that is unprotected by any bony structure. This alone could cause serious or fatal injuries. To reduce the risk of serious or fatal injuries during a crash, young children should always be secured in appropriate child restraints.


Child Restraint Systems


Rear-Facing Infant Seat


A rear-facing infant seat provides restraint with the seating surface against the back of the infant. The harness system holds the infant in place and, in a crash, acts to keep the infant positioned in the restraint.


Buick LaCrosse Owner Manual - 2013 - 1st crc - 4/18/12


Black plate (37,1)


Forward-Facing Child Seat


Booster Seats


A forward-facing child seat provides restraint for the child's body with the harness.


A booster seat is a child restraint designed to improve the fit of the vehicle's safety belt system. A booster seat can also help a child to see out the window.


Seats and Restraints


3-37


Securing an Add-On Child Restraint in the Vehicle { WARNING


A child can be seriously injured or killed in a crash if the child restraint is not properly secured in the vehicle. Secure the child restraint properly in the vehicle using the vehicle safety belt or LATCH system, following the instructions that came with that child restraint and the instructions in this manual.


To help reduce the chance of injury, the child restraint must be secured in the vehicle. Child restraint systems must be secured in vehicle seats by lap belts or the lap belt portion of a lap-shoulder belt, or by the LATCH system. See Lower Anchors and Tethers for Children (LATCH System) on page 3‑39.


Buick LaCrosse Owner Manual - 2013 - 1st crc - 4/18/12


Black plate (38,1)


3-38


Seats and Restraints


Children can be endangered in a crash if the child restraint is not properly secured in the vehicle. When securing an add-on child restraint, refer to the instructions that come with the restraint which may be on the restraint itself or in a booklet, or both, and to this manual. The child restraint instructions are important, so if they are not available, obtain a replacement copy from the manufacturer. Keep in mind that an unsecured child restraint can move around in a collision or sudden stop and injure people in the vehicle. Be sure to properly secure any child restraint in the vehicle — even when no child is in it. In some areas, Certified Child Passenger Safety Technicians (CPSTs) are available to inspect and demonstrate how to correctly use and install child restraints. In the U.S., refer to the National Highway Traffic Safety Administration (NHTSA) website to


locate the nearest child safety seat inspection station. For CPST availability in Canada, check with Transport Canada or the Provincial Ministry of Transportation office. Securing the Child within the Child Restraint


{ WARNING


A child can be seriously injured or killed in a crash if the child is not properly secured in the child restraint. Secure the child properly following the instructions that came with that child restraint.


Where to Put the Restraint According to accident statistics, children and infants are safer when properly restrained in a child restraint system or infant restraint system secured in a rear seating position.


We recommend that children and child restraints be secured in a rear seat, including: an infant or a child riding in a rear-facing child restraint; a child riding in a forward-facing child seat; an older child riding in a booster seat; and children, who are large enough, using safety belts. A label on your sun visor says, “Never put a rear-facing child seat in the front.” This is because the risk to the rear-facing child is so great if the airbag deploys.


{ WARNING


A child in a rear-facing child restraint can be seriously injured or killed if the right front passenger airbag inflates. This is because the back of the rear-facing child restraint would be very close to the inflating airbag. A child in a forward-facing child restraint can be seriously injured or killed if the right front


(Continued)


Buick LaCrosse Owner Manual - 2013 - 1st crc - 4/18/12


Black plate (39,1)


WARNING (CONTINUED)


passenger airbag inflates and the passenger seat is in a forward position. Even if the passenger sensing system has turned off the right front passenger frontal airbag, no system is fail-safe. No one can guarantee that an airbag will not deploy under some unusual circumstance, even though it is turned off. Secure rear-facing child restraints in a rear seat, even if the airbag is off. If you secure a forward-facing child restraint in the right front seat, always move the front passenger seat as far back as it will go. It is better to secure the child restraint in a rear seat. See Passenger Sensing System on page 3‑26 for additional information.


When securing a child restraint in a rear seating position, study the instructions that came with your child restraint to make sure it is compatible with this vehicle. Child restraints and booster seats vary considerably in size, and some may fit in certain seating positions better than others. Always make sure the child restraint is properly secured. Depending on where you place the child restraint and the size of the child restraint, you may not be able to access adjacent safety belt assemblies or LATCH anchors for additional passengers or child restraints. Adjacent seating positions should not be used if the child restraint prevents access to or interferes with the routing of the safety belt. Wherever a child restraint is installed, be sure to secure the child restraint properly.


Seats and Restraints


3-39


Keep in mind that an unsecured child restraint can move around in a collision or sudden stop and injure people in the vehicle. Be sure to properly secure any child restraint in your vehicle — even when no child is in it.


Lower Anchors and Tethers for Children (LATCH System) The LATCH system secures a child restraint during driving or in a crash. LATCH attachments on the child restraint are used to attach the child restraint to the anchors in the vehicle. This system is designed to make installation of a child restraint easier. Make sure that a LATCH-compatible child restraint is properly installed using the anchors, or use the vehicle's safety belts to secure the restraint, following the instructions that came with that restraint, and also the instructions in this manual. When installing a child restraint with


Buick LaCrosse Owner Manual - 2013 - 1st crc - 4/18/12


Black plate (40,1)


3-40


Seats and Restraints


a top tether, you must also use either the lower anchors or the safety belts to properly secure the child restraint. A child restraint must never be installed using only the top tether and anchor. In order to use the LATCH system in the vehicle, you need a child restraint that has LATCH attachments. The child restraint manufacturer will provide you with instructions on how to use the child restraint and its attachments. The following explains how to attach a child restraint with these attachments in the vehicle. Not all vehicle seating positions or child restraints have lower anchors and attachments or top tether anchors and attachments.


Lower Anchors


Top Tether Anchor


Lower anchors (1) are metal bars built into the vehicle. There are two lower anchors for each LATCH seating position that will accommodate a child restraint with lower attachments (2).


A top tether (3, 4) anchors the top of the child restraint to the vehicle. A top tether anchor is built into the vehicle. The top tether attachment (2) on the child restraint connects to the top tether anchor in the vehicle in order to reduce the forward movement and rotation of the child restraint during driving or in a crash.


Buick LaCrosse Owner Manual - 2013 - 1st crc - 4/18/12


Black plate (41,1)


The child restraint may have a single tether (3) or a dual tether (4). Either will have a single attachment (2) to secure the top tether to the anchor. Some child restraints that have a top tether are designed for use with or without the top tether being attached. Others require the top tether always to be attached. In Canada, the law requires that forward-facing child restraints have a top tether, and that the tether be attached. Be sure to read and follow the instructions for the child restraint.


Seats and Restraints


3-41


Lower Anchor and Top Tether Anchor Locations


To assist in locating the lower anchors, each rear anchor position has a label, near the crease between the seatback and the seat cushion.


Rear Seat


I (Top Tether Anchor): Seating positions with top tether anchors. H (Lower Anchor): Seating positions with two lower anchors.


To assist in locating the top tether anchors, the top tether anchor symbol is on the cover.


Buick LaCrosse Owner Manual - 2013 - 1st crc - 4/18/12


Black plate (42,1)


3-42


Seats and Restraints


According to accident statistics, children and infants are safer when properly restrained in a child restraint system or infant restraint system secured in a rear seating position. See Where to Put the Restraint on page 3‑38 for additional information. Securing a Child Restraint Designed for the LATCH System


{ WARNING


If a LATCH-type child restraint is not attached to anchors, the child restraint will not be able to protect the child correctly. In a crash, the child could be seriously injured or killed. Install a LATCH-type child restraint properly using the anchors, or use the vehicle safety belts to secure the restraint, following the instructions that came with the child restraint and the instructions in this manual.


{ WARNING


Do not attach more than one child restraint to a single anchor. Attaching more than one child restraint to a single anchor could cause the anchor or attachment to come loose or even break during a crash. A child or others could be injured. To reduce the risk of serious or fatal injuries during a crash, attach only one child restraint per anchor.


{ WARNING


Children can be seriously injured or strangled if a shoulder belt is wrapped around their neck and the safety belt continues to tighten. Buckle any unused safety belts behind the child restraint so children cannot reach them. Pull the shoulder belt all the way out


(Continued)


The top tether anchors are under the covers, behind the rear seat, on the filler panel. Be sure to use an anchor on the same side of the vehicle as the seating position where the child restraint will be placed. Do not secure a child restraint in a position without a top tether anchor if a national or local law requires that the top tether be attached, or if the instructions that come with the child restraint say that the top tether must be attached.


Buick LaCrosse Owner Manual - 2013 - 1st crc - 4/18/12


Black plate (43,1)


but you can install two of them. If you want to do this, install one LATCH child restraint in the right rear seating position, and install the other one either in the left rear seating position or in the center seating position. If you need to install child restraints in both the center and left rear seating positions, the one in the center seating position will need to be secured using the vehicle safety belts instead of the LATCH anchors. Refer to the following illustration to learn which anchors to use.


WARNING (CONTINUED)


of the retractor to set the lock, if the vehicle has one, after the child restraint has been installed.


Notice: Do not let the LATCH attachments rub against the vehicle’s safety belts. This may damage these parts. If necessary, move buckled safety belts to avoid rubbing the LATCH attachments. Do not fold the empty rear seat with a safety belt buckled. This could damage the safety belt or the seat. Unbuckle and return the safety belt to its stowed position, before folding the seat. If you need to secure more than one child restraint in the rear seat, see Where to Put the Restraint on page 3‑38. You cannot secure three child restraints using the LATCH anchors in the rear seat at the same time,


Seats and Restraints


3-43


There are five lower LATCH anchors in the rear seat. . Use anchors 1 and 2 when


installing a child restraint using LATCH in the right rear seating position.


. Use anchors 3 and 4 when


installing a child restraint using LATCH in the center rear seating position.


. Use anchors 4 and 5 when


installing a child restraint using LATCH in the left rear seating position.


Installing child restraints using LATCH in the center and left rear seating positions at the same time is prohibited. Make sure to attach the child restraint at the proper anchor location. This system is designed to make installation of child restraints easier. When using lower anchors, do not use the vehicle's safety belts. Instead use the vehicle's anchors


Buick LaCrosse Owner Manual - 2013 - 1st crc - 4/18/12


Black plate (44,1)


2.2. Route, attach, and tighten the top tether according to the child restraint instructions and the following instructions:


2.


“Head Restraint Removal and Reinstallation” at the end of this section.


1.3. Attach and tighten the lower


attachments on the child restraint to the lower anchors.


If the child restraint manufacturer recommends that the top tether be attached, attach and tighten the top tether to the top tether anchor, if equipped. Refer to the child restraint instructions and the following steps: 2.1. Find the top tether anchor. Open the cover to expose the anchor.


3-44


Seats and Restraints


and child restraint attachments to secure the restraints. Some restraints also use another vehicle anchor to secure a top tether. 1. Attach and tighten the lower


attachments to the lower anchors. If the child restraint does not have lower attachments or the desired seating position does not have lower anchors, secure the child restraint with the top tether and the safety belts. Refer to the child restraint manufacturer instructions and the instructions in this manual. 1.1. Find the lower anchors for


the desired seating position.


1.2. Put the child restraint on


the seat. If the head restraint interferes with the proper installation of the child restraint, the head restraint may be removed. See


Buick LaCrosse Owner Manual - 2013 - 1st crc - 4/18/12


Black plate (45,1)


If the position you are using does not have a headrest or head restraint, or the headrest or head restraint has been removed, and you are using a single tether, route the tether over the seatback.


If the position you are using does not have a headrest or head restraint, or the headrest or head restraint has been removed, and you are using a dual tether, route the tether over the seatback.


Seats and Restraints


3-45


If the position you are using has an adjustable headrest or head restraint and you are using a single tether, route the tether under the headrest or head restraint and in between the headrest or head restraint posts.


If the position you are using has an adjustable headrest or head restraint and you are using a dual tether, route the tether around the headrest or head restraint.


Buick LaCrosse Owner Manual - 2013 - 1st crc - 4/18/12


Black plate (46,1)


3-46


Seats and Restraints


3. Before placing a child in the


child restraint, make sure it is securely held in place. To check, grasp the child restraint at the LATCH path and attempt to move it side to side and back and forth. There should be no more than 2.5 cm (1 in) of movement, for proper installation.


Head Restraint Removal and Reinstallation The rear outboard head restraints can be removed if they interfere with the proper installation of the child restraint. To remove the head restraint: 1. Partially fold the seatback


forward. See Rear Seats on page 3‑10 for additional information.


2. Press both buttons on the head restraint posts at the same time, and pull up on the head restraint.


3. Store the head restraint in the


trunk of the vehicle.


4. When the child restraint is removed, reinstall the head restraint before the seating position is used.


{ WARNING


With head restraints that are not installed and adjusted properly, there is a greater chance that occupants will suffer a neck/ spinal injury in a crash. Do not drive until the head restraints for all occupants are installed and adjusted properly.


Buick LaCrosse Owner Manual - 2013 - 1st crc - 4/18/12


Black plate (47,1)


To reinstall the head restraint:


3. Try to move the head restraint to


make sure that it is locked in place.


Replacing LATCH System Parts After a Crash { WARNING


A crash can damage the LATCH system in the vehicle. A damaged LATCH system may not properly secure the child restraint, resulting in serious injury or even death in a crash. To help make sure the LATCH system is working properly after a crash, see your dealer to have the system inspected and any necessary replacements made as soon as possible.


If the vehicle has the LATCH system and it was being used during a crash, new LATCH system parts may be needed.


1.


Insert the head restraint posts into the holes in the top of the seatback. The notches on the posts must face the driver side of the vehicle.


2. Push the head restraint down. If necessary, press the height adjustment release button to further lower the head restraint. See Head Restraints on page 3‑2.


Seats and Restraints


3-47


New parts and repairs may be necessary even if the LATCH system was not being used at the time of the crash.


Securing Child Restraints (Rear Seat) When securing a child restraint in a rear seating position, study the instructions that came with the child restraint to make sure it is compatible with this vehicle. If the child restraint has the LATCH system, see Lower Anchors and Tethers for Children (LATCH System) on page 3‑39 for how and where to install the child restraint using LATCH. If a child restraint is secured in the vehicle using a safety belt and it uses a top tether, see Lower Anchors and Tethers for Children (LATCH System) on page 3‑39 for top tether anchor locations. Do not secure a child seat in a position without a top tether anchor if a national or local law requires


Buick LaCrosse Owner Manual - 2013 - 1st crc - 4/18/12


Black plate (48,1)


3-48


Seats and Restraints


that the top tether be anchored, or if the instructions that come with the child restraint say that the top strap must be anchored. If the child restraint does not have the LATCH system, you will be using the safety belt to secure the child restraint in this position. Be sure to follow the instructions that came with the child restraint. Secure the child in the child restraint when and as the instructions say. If more than one child restraint needs to be installed in the rear seat, be sure to read Where to Put the Restraint on page 3‑38. 1. Put the child restraint on


the seat. If the head restraint interferes with the proper installation of the child restraint, the head restraint may be removed. See “Head Restraint Removal and Reinstallation” under Lower Anchors and Tethers for Children (LATCH System) on page 3‑39.


2. Pick up the latch plate, and run the lap and shoulder portions of the vehicle's safety belt through or around the restraint. The child restraint instructions will show you how.


3. Push the latch plate into the


buckle until it clicks. Position the release button on the buckle so that the safety belt could be quickly unbuckled if necessary.


4. Pull the shoulder belt all the way


out of the retractor to set the lock. When the retractor lock is set, the belt can be tightened but not pulled out of the retractor.


Buick LaCrosse Owner Manual - 2013 - 1st crc - 4/18/12


Black plate (49,1)


Seats and Restraints


3-49


and Tethers for Children (LATCH System) on page 3‑39 for additional information on installing the head restraint properly.


Securing Child Restraints (Front Passenger Seat) This vehicle has airbags. A rear seat is a safer place to secure a forward-facing child restraint. See Where to Put the Restraint on page 3‑38. In addition, the vehicle has a passenger sensing system which is designed to turn off the right front passenger frontal airbag and seat‐ mounted side impact airbag under certain conditions. See Passenger Sensing System on page 3‑26 and Passenger Airbag Status Indicator on page 5‑15 for more information, including important safety information.


6.


If the child restraint has a top tether, follow the child restraint manufacturer's instructions regarding the use of the top tether. See Lower Anchors and Tethers for Children (LATCH System) on page 3‑39 for more information.


7. Before placing a child in the


child restraint, make sure it is securely held in place. To check, grasp the child restraint at the safety belt path and attempt to move it side to side and back and forth. When the child restraint is properly installed, there should be no more than 2.5 cm (1 in) of movement. To remove the child restraint, unbuckle the vehicle safety belt and let it return to the stowed position. If the top tether is attached to a top tether anchor, disconnect it. If the head restraint was removed, reinstall it before the seating position is used. See “Head Restraint Removal and Reinstallation” under Lower Anchors


5. To tighten the belt, push down on the child restraint, pull the shoulder portion of the belt to tighten the lap portion of the belt, and feed the shoulder belt back into the retractor. When installing a forward-facing child restraint, it may be helpful to use your knee to push down on the child restraint as you tighten the belt. Try to pull the belt out of the retractor to make sure the retractor is locked. If the retractor is not locked, repeat Steps 4 and 5.


Buick LaCrosse Owner Manual - 2013 - 1st crc - 4/18/12


Black plate (50,1)


3-50


Seats and Restraints


A label on the sun visor says, “Never put a rear-facing child seat in the front.” This is because the risk to the rear-facing child is so great if the airbag deploys.


{ WARNING


A child in a rear-facing child restraint can be seriously injured or killed if the right front passenger airbag inflates. This is because the back of the rear-facing child restraint would be very close to the inflating airbag. A child in a forward-facing child restraint can be seriously injured or killed if the right front passenger airbag inflates and the passenger seat is in a forward position. Even if the passenger sensing system has turned off the right front passenger frontal airbag, no system is fail-safe. No one can guarantee that an airbag will not


(Continued)


WARNING (CONTINUED)


deploy under some unusual circumstance, even though it is turned off. Secure rear-facing child restraints in a rear seat, even if the airbag is off. If you secure a forward-facing child restraint in the right front seat, always move the front passenger seat as far back as it will go. It is better to secure the child restraint in a rear seat. See Passenger Sensing System on page 3‑26 for additional information.


If the child restraint has the LATCH system, see Lower Anchors and Tethers for Children (LATCH System) on page 3‑39 for how and where to install the child restraint using LATCH. If a child restraint is secured using a safety belt and it uses a top tether, see Lower


Anchors and Tethers for Children (LATCH System) on page 3‑39 for top tether anchor locations. Do not secure a child seat in a position without a top tether anchor if a national or local law requires that the top tether be anchored, or if the instructions that come with the child restraint say that the top strap must be anchored. In Canada, the law requires that forward-facing child restraints have a top tether, and that the tether be attached. You will be using the lap-shoulder belt to secure the child restraint in this position. Follow the instructions that came with the child restraint. 1. Move the seat as far back as it


will go before securing the forward-facing child restraint. When the passenger sensing system has turned off the right front passenger frontal airbag and seat‐mounted side airbag, the off indicator on the


Buick LaCrosse Owner Manual - 2013 - 1st crc - 4/18/12


Black plate (51,1)


Seats and Restraints


3-51


4. Push the latch plate into the


buckle until it clicks. Position the release button on the buckle so that the safety belt could be quickly unbuckled if necessary.


passenger airbag status indicator should light and stay lit when you start the vehicle. See Passenger Airbag Status Indicator on page 5‑15.


2. Put the child restraint on


the seat.


3. Pick up the latch plate, and run the lap and shoulder portions of the vehicle's safety belt through or around the restraint. The child restraint instructions will show you how.


5. Pull the shoulder belt all the way


out of the retractor to set the lock. When the retractor lock is set, the belt can be tightened but not pulled out of the retractor.


6. To tighten the belt, push down on the child restraint, pull the shoulder portion of the belt to tighten the lap portion of the belt, and feed the shoulder belt back into the retractor. When installing a forward-facing child restraint, it may be helpful to use your knee to push down on the child restraint as you tighten the belt. Try to pull the belt out of the retractor to make sure the retractor is locked. If the retractor is not locked, repeat Steps 5 and 6.


Buick LaCrosse Owner Manual - 2013 - 1st crc - 4/18/12


Black plate (52,1)


3-52


Seats and Restraints


7. Before placing a child in the


child restraint, make sure it is securely held in place. To check, grasp the child restraint at the safety belt path and attempt to move it side to side and back and forth. When the child restraint is properly installed, there should be no more than 2.5 cm (1 in) of movement.


If the airbags are off, the off indicator in the passenger airbag status indicator will come on and stay on when the vehicle is started. If a child restraint has been installed and the on indicator is lit, see “If the On Indicator Is Lit for a Child Restraint” under Passenger Sensing System on page 3‑26 for more information. To remove the child restraint, unbuckle the vehicle safety belt and let it return to the stowed position.


Buick LaCrosse Owner Manual - 2013 - 1st crc - 4/10/12


Black plate (1,1)


Storage


4-1


Storage


Storage Compartments


Front Storage


Storage Compartments


Glove Box . . . . . . . . . . . . . . . . . . . . 4-1
Cupholders . . . . . . . . . . . . . . . . . . . 4-1
Front Storage . . . . . . . . . . . . . . . . . 4-1
Center Console Storage . . . . . . 4-2


Additional Storage Features


Convenience Net . . . . . . . . . . . . . 4-2


Glove Box The glove box is located on the passenger side of the instrument panel. Lift up on the lever to open it.


Cupholders


Pull up on the handle and pull the cover down to open.


There are removable cupholders in the center console. Slide the cover to access the cupholders. Cupholders are also in the rear center armrest.


Buick LaCrosse Owner Manual - 2013 - 1st crc - 4/10/12


Black plate (2,1)


Additional Storage Features


Convenience Net Use the convenience net located in the trunk to store small loads as far forward as possible. The net should not be used to store heavy loads. Attach the net so the opening is facing up. Attach the net loops to the hooks on the rear panel of the trunk.


4-2


Storage


Center Console Storage


The armrest can be adjusted by sliding it to the desired position. The center console has an upper tray and a lower main storage area. To access the main storage area, adjust the armrest to the rear position and push button (1) to open. Push button (2) to access the upper tray. An accessory power outlet is in the lower area. See Power Outlets on page 5‑6. Some vehicles may also have input jacks for auxiliary audio devices. See Auxiliary Devices on page 7‑18.


Buick LaCrosse Owner Manual - 2013 - 1st crc - 4/10/12


Black plate (1,1)


Instruments and Controls


5-1


Instruments and Controls


Controls


Steering Wheel Adjustment . . . 5-2
Steering Wheel Controls . . . . . . 5-2
Heated Steering Wheel . . . . . . . 5-3
Horn . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3
Windshield Wiper/Washer . . . . . 5-3
Compass . . . . . . . . . . . . . . . . . . . . . 5-4
Clock (Radio with CD and


Touchscreen) . . . . . . . . . . . . . . . . 5-5
Power Outlets . . . . . . . . . . . . . . . . . 5-6


Warning Lights, Gauges, and Indicators


Warning Lights, Gauges, and


Indicators . . . . . . . . . . . . . . . . . . . . 5-8
Instrument Cluster . . . . . . . . . . . . 5-9
Speedometer . . . . . . . . . . . . . . . . 5-11
Odometer . . . . . . . . . . . . . . . . . . . . 5-11
Tachometer . . . . . . . . . . . . . . . . . . 5-11
Fuel Gauge . . . . . . . . . . . . . . . . . . 5-11
Driver Efficiency Gauge . . . . . . 5-12
Engine Coolant Temperature


Gauge . . . . . . . . . . . . . . . . . . . . . . 5-13
Safety Belt Reminders . . . . . . . 5-13


Airbag Readiness Light . . . . . . 5-14
Passenger Airbag Status


Indicator . . . . . . . . . . . . . . . . . . . . 5-15
Charging System Light . . . . . . 5-15
Malfunction


Indicator Lamp . . . . . . . . . . . . . 5-16


Brake System Warning


Light . . . . . . . . . . . . . . . . . . . . . . . 5-18


Electric Parking Brake


Light . . . . . . . . . . . . . . . . . . . . . . . 5-19


Antilock Brake System (ABS)


Warning Light . . . . . . . . . . . . . . 5-19
Traction Off Light . . . . . . . . . . . . 5-20
StabiliTrak® OFF Light . . . . . . . 5-20
Traction Control System


(TCS)/StabiliTrak® Light . . . . 5-21


Engine Coolant Temperature


Warning Light . . . . . . . . . . . . . . 5-22
Tire Pressure Light . . . . . . . . . . 5-22
Engine Oil Pressure Light . . . . 5-23
Low Fuel Warning Light . . . . . . 5-23
Security Light . . . . . . . . . . . . . . . . 5-23
High-Beam On Light . . . . . . . . . 5-24
Front Fog Lamp Light . . . . . . . . 5-24
Lamps On Reminder . . . . . . . . . 5-24
Cruise Control Light . . . . . . . . . 5-24
Door Ajar Light . . . . . . . . . . . . . . 5-25


Information Displays


Driver Information


Center (DIC) . . . . . . . . . . . . . . . 5-25
Head-Up Display (HUD) . . . . . 5-29


Vehicle Messages


Vehicle Messages . . . . . . . . . . . 5-32
Battery Voltage and Charging


Messages . . . . . . . . . . . . . . . . . . 5-33
Brake System Messages . . . . 5-33
Compass Messages . . . . . . . . . 5-33
Cruise Control Messages . . . . 5-34
Door Ajar Messages . . . . . . . . . 5-34
Engine Cooling System


Messages . . . . . . . . . . . . . . . . . . 5-34
Engine Oil Messages . . . . . . . . 5-35
Engine Power Messages . . . . 5-35
Fuel System Messages . . . . . . 5-35
Key and Lock Messages . . . . . 5-36
Lamp Messages . . . . . . . . . . . . . 5-36
Object Detection System


Messages . . . . . . . . . . . . . . . . . . 5-36


Ride Control System


Messages . . . . . . . . . . . . . . . . . . 5-37
Security Messages . . . . . . . . . . 5-37
Starting the Vehicle


Messages . . . . . . . . . . . . . . . . . . 5-37


Buick LaCrosse Owner Manual - 2013 - 1st crc - 4/10/12


Black plate (2,1)


5-2


Instruments and Controls


Tire Messages . . . . . . . . . . . . . . . 5-38
Transmission Messages . . . . . 5-38
Window Messages . . . . . . . . . . . 5-39


Vehicle Personalization


Vehicle Personalization . . . . . . 5-39


Universal Remote System


Controls


Steering Wheel Adjustment


Do not adjust the steering wheel while driving.


Steering Wheel Controls


Universal Remote System . . . 5-45
Universal Remote System


Programming . . . . . . . . . . . . . . . 5-45


Universal Remote System


Operation . . . . . . . . . . . . . . . . . . 5-48


To adjust the steering wheel: 1. Pull the lever down. 2. Move the steering wheel up


or down.


3. Pull or push the steering wheel


closer or away from you.


4. Pull the lever up to lock the


steering wheel in place.


For vehicles with audio steering wheel controls, some audio controls can be adjusted at the steering wheel. b / g (Push to Talk): For vehicles with a Bluetooth®, OnStar, or navigation system, press to interact with those systems. See Bluetooth (Overview) on page 7‑20
or Bluetooth (Infotainment Controls)


Buick LaCrosse Owner Manual - 2013 - 1st crc - 4/10/12


Black plate (3,1)


Instruments and Controls


5-3


on page 7‑22 or Bluetooth (Voice Recognition) on page 7‑25, OnStar Overview on page 14‑1, or the navigation manual for more information. $ / i (Mute/End Call): Press to silence the vehicle speakers only. Press again to turn the sound on. For vehicles with OnStar or Bluetooth systems, press to reject an incoming call, or end a current call. _ SRC ^ (Thumbwheel Control): Turn to select an audio source. Press _ or ^ to select the next or previous favorite radio station, CD, or MP3 track. + x − (Volume): Press + to increase the volume. Press − to decrease the volume.


Heated Steering Wheel For vehicles with a heated steering wheel, the button for this feature is located on the climate control system. ( (Heated Steering Wheel): Press to turn the heated steering wheel on or off. A light on the button displays when the feature is turned on. The steering wheel takes about three minutes to start heating.


Horn Press a on the steering wheel pad to sound the horn.


Windshield Wiper/Washer


The windshield wiper/washer lever is on the right side of the steering column. With the ignition in ACC/ ACCESSORY or ON/RUN, move the windshield wiper lever to select the wiper speed. HI: Use for fast wipes. LO: Use for slow wipes.


INT: (Intermittent Wipes): Move the lever up to INT for intermittent wipes, then turn the 3 INT band up for more frequent wipes or down for less frequent wipes. OFF: Use to turn the wipers off. 8 (Mist): For a single wipe, briefly move the wiper lever down. For several wipes, hold the wiper lever down.


Buick LaCrosse Owner Manual - 2013 - 1st crc - 4/10/12


Black plate (4,1)


5-4


Instruments and Controls


n L (Windshield Washer): Pull the windshield wiper lever toward you to spray windshield washer fluid and activate the wipers. The wipers will continue until the lever is released or the maximum wash time is reached. When the windshield wiper lever is released, additional wipes may occur depending on how long the windshield washer had been activated. See Washer Fluid on page 10‑24 for information on filling the windshield washer fluid reservoir.


{ WARNING


In freezing weather, do not use the washer until the windshield is warmed. Otherwise the washer fluid can form ice on the windshield, blocking your vision.


Clear snow and ice from the wiper blades and windshield before using them. If frozen to the windshield, carefully loosen or thaw them.


Damaged blades should be replaced. See Wiper Blade Replacement on page 10‑30. Heavy snow or ice can overload the wiper motor.


Wipe Parking If the ignition is turned to LOCK/ OFF while the wipers are on LO, HI, or INT, they will immediately stop. If the windshield wiper lever is then moved to off before the driver door is opened or within 10 minutes, the wipers will restart and move to the base of the windshield. If the ignition is turned to LOCK/ OFF while the wipers are performing wipes due to windshield washing, the wipers continue to run until they reach the base of the windshield.


Compass The vehicle may have a compass display on the Driver Information Center (DIC). The compass receives its heading and other information from the Global Positioning System (GPS) antenna, StabiliTrak, and vehicle speed information. Avoid covering the GPS antenna for long periods of time with objects that may interfere with the antenna's ability to receive a satellite signal. See Backglass Antenna on page 7‑13 and Satellite Radio Antenna on page 7‑14 for the location of the vehicle's antennas. The compass system is designed to operate for a certain number of miles or degrees of turn before needing a signal from the GPS satellites. When the compass display shows CAL, drive the vehicle for a short distance in an open area where it can receive a GPS signal. The compass system will automatically determine when the GPS signal is restored and


Buick LaCrosse Owner Manual - 2013 - 1st crc - 4/10/12


Black plate (5,1)


Instruments and Controls


5-5


provide a heading again. See Compass Messages on page 5‑33
for more information on the messages that may be displayed for the compass.


Clock (Radio with CD and Touchscreen) The infotainment system controls are used to access the time and date settings through the menu system. See Overview on page 7‑3
and Operation on page 7‑4 for information about how to use the menu system. Setting the Time (Without Date Display) 1. Press the CONFIG button and


select Time Settings, or press H.


2. Select Set Time. 3. Turn the Multifunction knob to


adjust the highlighted value.


4. Press SELECT to select the next


value.


5. To save the time and return to the Time Settings menu, press the / BACK button at any time or press SELECT after adjusting the minutes.


Setting the 12/24 Hour Format 1. Press the CONFIG button and


select Time Settings, or press H.


2. Highlight 12/24 Hour Format. 3. Press SELECT to select the


12 hour or 24 hour display format.


Setting the Time and Date (With Date Display) 1. Press the CONFIG button and select Time and Date Settings, or press H.


2. Select Set Time or Set Date. 3. Turn the Multifunction knob to


adjust the highlighted value.


4. Press SELECT to select the next


value.


5. To save the time or date and return to the Time and Date Settings menu, press the / BACK button at any time or press SELECT after adjusting the minutes or year.


Setting the 12/24 Hour Format 1. Press the CONFIG button and select Time and Date Settings, or press H.


2. Highlight Set Time Format. 3. Press SELECT to select the


12 hour or 24 hour display format.


Setting the Month and Day Format 1. Press the CONFIG button and select Time and Date Settings, or press H.


2. Highlight Set Date Format. 3. Press SELECT to select MM/


DD/YY (month/day/year) or DD/ MM/YY (day/month/year).


Buick LaCrosse Owner Manual - 2013 - 1st crc - 4/10/12


Black plate (6,1)


5-6


Instruments and Controls


Setting the Auto Time Adjust 1. Press the CONFIG button and select Time and Date Settings, or press H.


2. Highlight Auto Time Adjust. 3. Press SELECT to turn Auto


Time Adjust on or off.


4. Press SELECT button to select Time Zone, and then select the Time Zone.


5. Press SELECT to turn Daylight


Savings on or off.


Setting the Time and Date (Radio with CD and Touchscreen) To set the time: 1. Press the CONFIG button to


enter the menu options. Turn the Multifunction knob to scroll through the available setup features. Press the SELECT knob or press the Time screen button to display other options within that feature.


2. Press + or − to decrease or


increase the Hours and Minutes displayed on the clock.


12/24 HR Format: Press the 12 HR screen button for standard time; press the 24 HR screen button for military time. Day + or Day −: Press the Day + or Day − display buttons to increase or decrease the day. Display: Press Display to turn the display of the time on the screen on or off.


Power Outlets

Loading...
x