Login- Download PDF Manual
-
–
–
–
– –
6.5Jx15
7Jx16
– –
7Jx16
7.5Jx17
8.5Jx177Jx15
7Jx16
7.5Jx17
8Jx173.00Bx16
–
Use the spare wheel only for short distances (to reach the nearest BMW center, for instance). Due to the altered handling characteristics, do not exceed a maximum speed of 50 mph (80 km/h). Mounting snow chains on the spare tire is not possible. Be sure that all tires are properly inflated, refer to page 27.
The use of rims and lug bolts that do not meet the specifications of the original factory-installed equipment will affect the safe operation of your vehicle and may cause an accident and personal injury. Never mix tires of different design, such as steel-belted radials with bias-belted or bias-ply tires etc. Mixing tire types will adversely affect road-holding and can lead to loss of vehicle control.<
Approved wheel and tire specifications
117n
BMW tests certain tire brands for each tire size, classifies them as road-safe and approves them. Consult your BMW center for more information. Observe any regulations applicable in the country of use, e.g. requiring entry in the vehicle documents.
Z3 roadster 3.0i, Z3 coupe 3.0i Summer 225/50 R 16 92 V 225/50 ZR 16
Front: 225/45 ZR 17
Rear: 245/40 ZR 17
Winter (M+S) 205/55 R 16 91 Q/T/H 225/50 R 16 92 Q/T/H225/45 R 17 91 Q
Spare tire T 115/90 R 16 92 M
– –
–
–
– –
7Jx16
– –
7Jx16
7.5Jx17
8.5Jx177Jx16
7.5Jx17
8Jx173.00Bx16
–
Use the spare tire only for short distances (to reach the nearest BMW center, for instance). Due to the altered handling characteristics, do not exceed a maximum speed of 50 mph (80 km/h). Mounting snow chains on the spare tire is not possible. Be sure that all tires are properly inflated, refer to page 27.
The use of rims and lug bolts that do not meet the specifications of the original factory-installed equipment will affect the safe operation of your vehicle and may cause an accident and personal injury. Never mix tires of different design, such as steel-belted radials with bias-belted or bias-ply tires etc. Mixing tire types will adversely affect road-holding and can lead to loss of vehicle control.<
118n
Hood
Do not work on your vehicle without appropriate skills. Always
switch off the engine and allow it to cool down before working in the engine compartment. Always disconnect the battery before working on any electrical systems or equipment, especially when these are located within the engine compartment. Comply with all appli- cable instructions and warnings. If you are not familiar with all guidelines, have the work performed by your BMW center. Otherwise, safety hazards for vehicle occupants and other road users may occur as a result of improper handling of components and mate- rials.<
To release Pull the lever located under the left- hand side of the instrument panel.
To open Grasp the hood on both sides on the level of the latch (arrow 1); press the latch upward and simultaneously lift the hood with both hands.
Hood
To close Allow the hood to fall from a height of about 12 in (30 cm) so that it audibly engages.
To avoid injuries, be sure that the travel path of the hood is clear when it is closed, as with all closing procedures. If it is determined that the hood is not completely closed while driving, stop immediately and close it securely.<
119n
120nEngine compartment – Z3 roadster 2.5i, 3.0i, Z3 coupe 3.0i
Engine compartment – Z3 roadster 2.5i, 3.0i, Z3 coupe 3.0i
121n
1 Engine oil dipstick 123
2 Brake fluid reservoir,the illustration shows the reservoir for Z3 roadster 3.0i, Z3 coupe 3.0i 126
3 Fuse box 156
4 Coolant expansion tank 125
5 Engine oil filler neck 123
6 Reservoir for windshield and headlamp* washer fluid 1227 Auxiliary terminal for jump-starting –
negative terminal 158
8 Auxiliary terminal for jump-starting –
positive terminal 158
122nFluids for the washer systems
Washer nozzles
Antifreeze agent for the washer systems is flammable. For this
reason, keep it away from sources of flame and store it only in its original container. Store it so that it is inacces- sible to children. Comply with the instructions on the containers.<
Windshield washer system Windshield: The spray from the nozzles should be directed so as to ensure effective cleaning, even at high speeds. If necessary, correct the adjustment with a needle, or have the adjustment made by your BMW center. Rear window – Z3 coupe only: Have this system adjusted by your BMW center as required.
Headlamp washer system* Have this system adjusted by your BMW center as required.
Headlamp* and windshield washer system Capacity: approx. 5.3 US quarts (5.0 liters). Fill with water and – if required – with an antifreeze agent (according to the manufacturer's recommendations).
We recommend that you mix the washer fluid before adding it to
the reservoir.<
Engine oil
123n
To check oil level 1. Park the vehicle on a level surface 2. Switch the engine off after it has
reached normal operating tempera- ture
3. After approx. 5 minutes, pull the dipstick out and wipe it off with a clean lint-free cloth, paper towel, or similar material
4. Push the dipstick carefully all the way
into the guide tube and pull it out again
5. The oil level should be between the
two marks on the dipstick.
As with fuel economy, oil consumption is directly influenced by your driving style and vehicle operating conditions.
The space between the two marks on the dipstick corresponds to approx. 1.1 US quarts (1 liter). Do not fill beyond the upper mark on the dipstick. Excess oil will damage the engine.
To add oil While you should wait until the level has dropped to just above the lower mark before adding oil, you should never allow the oil level to fall below this mark.
BMW engines are designed to operate without oil additives; the use of additives could lead to damage in some cases. This also applies to the manual and automatic transmission, the differential and the power steering system.<
Viscosity – ratings Viscosity is the oilflow rating as estab- lished in SAE classes. The selection of the correct SAE class depends on the climatic conditions in the area where you drive your BMW.
Approved oils are in SAE classes 5W-40 and 5W-30.<
These oils may be utilized in all ambient temperatures.
124nEngine oil
Specified engine oils The quality of the engine oil which is selected has critical significance for the operation and service life of an engine. Based on extensive testing, BMW has approved only certain engine oils. Use only approved "BMW High Perfor- mance Synthetic Oil". If you are unable to obtain "BMW High Performance Synthetic Oil", you can add small amounts of synthetic oil in between oil changes. Only use oils with the API SH specification or higher.
Ask your BMW center for details concerning the specific "BMW High Performance Synthetic Oil" or "synthetic oils" which have been approved.<
You can also call BMW of North America at 1-800-831-1117 or visit this website: www.bmwusa.com to obtain this information.
Engine oil
Coolant
125n
Comply with the applicable envi- ronmental laws regulating the
disposal of used oil.<
Recommendation: have the oil changed by your BMW center only.
Continuous exposure to used oil has caused cancer in laboratory
testing. Any skin areas that come in contact with oil should thus be thor- oughly washed with soap and water. Store oil, grease, etc., out of reach of children. Comply with warning labels and information on containers. If you use SAE 15W-40 engine oil in low temperatures (below +14 7/–10 6), the engine may become difficult to start. Special engine oils individually approved by BMW are preferred for use in your engine. Please contact your BMW center for details.<
Do not add coolant to the cooling system when the engine is hot. If
you do, escaping coolant can cause burns. To avoid the possibility of damage later on, do not use anything other than factory-approved, nitrite and amino- free extended-duty antifreeze with corrosion inhibitor which can be used with aluminum radiator cores. Your BMW center is familiar with the approved specifications. Antifreeze and anti-corrosion agents are hazardous to health. Store them in their original containers. Keep the containers tightly closed and out of reach of children. Extended-duty antifreeze with corro- sion inhibitor contains the flammable substance ethylene glycol. For this reason, do not spill extended-duty anti- freeze with corrosion inhibitor on hot engine components. If you do, it could be ignited and cause burns.<
Comply with the applicable envi- ronmental laws regulating the
disposal of extended-duty antifreeze with corrosion inhibitor.<
Checking coolant level Correct coolant level when the engine is cold (approx. +68 7/+20 6): Unscrew the cap from the expansion tank. The coolant level is correct when the upper end of the red float is at least even with the upper edge of the filler neck (refer to the arrow in the illustra- tion), but no more than 0.8 in (2 cm) above it – that is, up to the second mark on the float (refer also to the schematic diagram next to the filler neck).
126nCoolant
Brake fluid
To add coolant Wait until the engine cools before removing the cap from the expansion tank. The needle of the coolant gauge in the instrument cluster must be located in the blue field; otherwise, there is a danger of scalding. 1. Turn the cap slightly counterclock- wise in order to allow accumulated pressure to escape, then open
2. If the coolant is low, slowly add coolant until the correct level is reached – do not overfill.
The coolant is a mixture of water and extended-duty antifreeze with corrosion inhibitor. Always maintain the prescribed all-season 50:50 mixture ratio for year-round protection against internal corrosion. No other additives are required. Replace the coolant regularly. Refer to the Service and Warranty Information Booklet (US models) or the Warranty and Service Guide Booklet (Canadian models).
Z3 roadster 2.5i
Z3 roadster 3.0i, Z3 coupe 3.0i
If the warning lamp for the brake hydraulic system comes on: The brake fluid level is too low, refer also to the instructions on page 104. For adding brake fluid or for deter- mining and correcting the cause of brake fluid loss, consult your BMW center. Your BMW center is familiar with the specifications for factory- approved brake fluids (DOT 4).
Brake fluid loss may result in extended brake pedal travel. If this occurs, refer to the notes on page 104.
Brake fluid is hygroscopic, that is, it absorbs moisture from the air
over time. In order to ensure the operating safety and reliability of the brake system, have the brake fluid changed every two years by a BMW center, refer also to the Service and Warranty Information Booklet (US models) or the Warranty and Service Guide Booklet (Canadian models).
Brake fluid
Vehicle Identification
127n
Brake fluid is hazardous to health and will damage the vehicle's paint. You should always store it in its original container and in a location which is inaccessible to children. Avoid brake fluid spills. Do not fill brake fluid beyond the "MAX" level in the reservoir. The brake fluid could ignite upon contact with hot engine parts and cause serious burns.<
Comply with the applicable envi- ronmental laws regulating the
disposal of brake fluid.<
The Vehicle Identification Number is located in the engine compartment below the windshield and on the top of the instrument panel.
128n
The BMW Maintenance System
The BMW Maintenance System includes the Engine Oil Service as well as Inspections I and II. Determining the maintenance intervals according to the actual loads on the vehicle covers every kind of operating situation. However, since oil deteriorates over time regardless of use, even those who drive only short distances – signifi- cantly less than 6,200 miles (10,000 km) annually – should have the engine oil changed regularly. Refer to the Service and Warranty Information Booklet (US models) or to the Warranty and Service Guide Booklet (Canadian models).
Service Interval Display Advanced technology is employed to calculate the optimal maintenance intervals, which are then indicated in the Service Interval Display. While conventional systems rely solely on distance traveled to determine when service is due, the BMW Maintenance System considers the actual conditions under which the vehicle operates. From the point of view of maintenance, 62,000 miles (100,000 km) accumulated in short-distance urban driving are not the equivalent of the same distance covered at moderate speeds in long- distance highway travel. In response to this fact, the BMW Maintenance System monitors operating conditions as the basis for determining the optimum service intervals for your indi- vidual vehicle.
The BMW Maintenance System has been designed as a reliable means of providing maximum driving and oper- ating safety – and as cost-effectively as possible for you. Please keep in mind that regular main- tenance is not only necessary for the safety of your vehicle, but also plays a significant role in maintaining the resale value of your vehicle.
The BMW Maintenance System
129n
Service and Warranty Information Booklet (US models)/Warranty and Service Guide Booklet (Canadian models) For detailed information on required maintenance items and the work involved, please refer to the Service and Warranty Information Booklet (US models) or to the Warranty and Service Guide Booklet (Canadian models). Depending upon operating conditions, it may be advisable to have the body checked for damage from rocks or gravel as a precaution against rust.
Have your BMW center perform the maintenance and repair.
Your BMW center is always informed on the latest maintenance work and repair techniques and is equipped with the required special tools. In addition, checking parts known from experience to be subject to wear is a permanent part of the maintenance specifications. Be sure that all maintenance work is confirmed in the Service and Warranty Information Booklet (US models) or the Warranty and Service Guide Booklet (Canadian models). These entries will constitute your proof that the vehicle has received regular maintenance. They are also required for warranty claims.<
Do not make modifications of any kind to the individual components or system wiring. These include the upholstered covers on the steering wheel hub, in the instrument panel and in the side trim panels of the doors. Never apply adhe- sive materials to these components or cover or modify them in any way. Do not attempt to disassemble the steering wheel itself. To ensure compliance with applicable safety regulations, have the airbag generators disposed of by a BMW center only. Unprofessional attempts to service the system could lead to failure in an emer- gency or undesired airbag activation, either of which could result in personal injury.<
130nAirbags
1 Front airbags on the driver and
passenger side
2 Side airbags on the driver and
passenger side
Important safety notices
Do not attempt to remove the gas generators of the airbag restraint
system from the vehicle or to disas- semble them. Have inspection and service proce- dures performed by specially-trained personnel only. If the airbag restraint system malfunc- tions, is deactivated or triggered as a response to an accident, have the system repaired by a BMW center only.
Storing your vehicle
If you intend to store the vehicle for longer than three months, have the maintenance operations described on this page performed.<
Preparation for storage Have the following operations performed by your BMW center: 1. Clean and apply a rust-proofing agent or other treatment to the engine, engine compartment, under- carriage, axles and major compo- nents in accordance with approved repair procedures. Wash the vehicle, clean the interior and treat painted and chromed parts. Clean the rubber seals around the hood, luggage compartment and doors
2. Change the engine oil and oil filter
with the engine at operating temper- ature. As an additional corrosion protection measure, an anticorrosive agent can be added to the engine in accordance with the manufacturer's instructions
3. Check the coolant level and concen-
tration and top up if necessary
4. Check the fluid level of the wind-
shield washer fluid reservoir; top up if necessary
During storage Recharge the battery every six months. If it is not recharged, it will not be serviceable. Every time the battery is discharged, especially over extended periods, its service life is reduced.
131n
Removing the vehicle from storage Recharge the battery if the "Magic Eye" turns black, refer to page 154. Then have Inspection I performed by your BMW center, including a brake fluid replacement if necessary, refer to the Service Manual.
Storing your vehicle
5. Fill the fuel tank completely to
prevent the formation of condensa- tion
6. Increase the tire inflation pressure to
51 psi (350 kPa).
Before parking the vehicle for storage 1. Dry the parking brake and footbrake by brake applications to prevent the brake rotors and drums from corroding
2. Park the vehicle in a covered, dry,
and well-ventilated room. Place the transmission in 1st gear or set the selector lever to the "P" position. Chock the wheels to prevent the vehicle from rolling if necessary. Do not set the parking brake
3. Remove the battery, charge it
completely and store it in a cool (but frost-free) room
Z3 roadster: 4. Remove the hardtop* and store it
separately, refer to page 109
5. Close the convertible top.
132n
Technical modifications
California Proposition 65 Warning
Any BMW center will be happy to advise you concerning the advisability, legal implications and factory recom- mendations for technical modifications to the vehicle. For this purpose, the BMW center will require the Vehicle Identification Number. The engine number is also required in some instances.
California laws require us to state the following warning:
Engine exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.<
Light-emitting diodes (LEDs) Light-emitting diodes installed behind translucent lenses serve as the light source for many of the controls and displays in your vehicle. These LEDs are similar to conventional laser tech- nology.
Do not remove the protective lens and avoid staring directly at the unfiltered beam for extended periods (several hours), since inflammation of the iris could result.<
133n
When the filler cap is not properly tightened, the OBD system can
detect the vapor leak and the indicator will light up. If the filler cap is subse- quently tightened, the indicator should go out within a few days.<
OBD interface socket
Access to the interface socket for the Onboard Diagnostic system (OBD): Lift off the side cover in the center console on the passenger's side (arrow). The purpose of the OBD system is to ensure proper operation of the emis- sion control system throughout the vehicle's lifetime by monitoring emis- sion-related components and systems for deterioration and malfunction.
An illuminated indicator informs you of the need for service, but not of the need to stop the vehicle. However, the systems should be checked by your BMW center at the earliest possible opportunity. Under certain conditions, the indicator will blink or flash. This indicates a rather severe level of engine misfire. When this occurs, you should reduce speed and consult the nearest BMW center as soon as possible. Severe engine misfire over only a short period of time can seriously damage emission control components, especially the catalytic converter.
"Service Engine Soon" warning lamp for Canadian models.
134n
Replacement procedures: Onboard tool kit 136
Windshield wiper blades 136
Lamps and bulbs 137
Master key with batterylamp 143
Remote control 144
Wheel change 146
Battery 153
Fuses 156In case of electrical malfunction: Power convertible top 157
Fuel filler door 157Assistance, giving and receiving: Jump-starting 158
Towing the vehicle 159135n
Overview
Controls and features
Operation, maintenance
Owner service procedures
Advanced technology
Technical data
Index
Repairs
136n
Onboard tool kit
Windshield wiper blades
The onboard tool kit is located in the luggage compartment, under the floor mat. Z3 coupe: Grasp the floor mat by the straps on the left and right. Pull it upward and remove it. Z3 roadster: Lift the floor mat from the rear by the strap and fold it forward.
Front 1. Position the wipers vertically. To do this, switch on the wipers and switch off the ignition when the wipers are approximately vertical
2. Raise the wiper arm completely 3. Press the spring retainer (arrow) and extract the blade, pulling toward the wiper arm
4. Insert a new wiper blade and apply
pressure until you hear it engage.
Rear window wiper – Z3 coupe Follow the same procedure as described for changing the front wiper blades, except that the wiper does not have to be positioned vertically.
Fold the wipers back onto the window before you turn the igni-
tion key to position 1 or 2.<
Use only wiper blades which have been approved by BMW.<
Lamps and bulbs
The lamps and bulbs make essential contributions to the safety of your vehicle. Therefore, comply fully with the following instructions during bulb replacement. If you are not familiar with any of the procedures, consult your BMW center.
Do not touch the glass portion of a new bulb with your bare hands since even small amounts of impurities burn in to the surface and reduce the service life of the bulb. Use a clean cloth, paper napkin, or a similar mate- rial, or hold the bulb by its metallic base.<
A replacement bulb set is available from your BMW center.
Before working on the electrical system, switch off the electrical
accessory you are working on or disconnect the cable from the negative terminal of the battery. Failure to observe this precaution could result in short circuits. To prevent injuries and damage, comply with any instructions provided by the bulb manufacturer.<
The illustration depicts the right side of the engine compartment.
1 High beams HB3 bulb, 65 watts
2 Low beams HB4 bulb, 55 watts
The bulb is pressurized. There- fore, wear safety glasses and protective gloves. Failure to comply with these precautions could result in physical injury if the bulb breaks.<
137n
1. Turn the bulb holder with the bulb to
the left and remove toward the rear
2. Pull off the plug 3. Push the new bulb holder with the bulb into the plug – ensure proper locking
4. Reinstall in reverse order.
When cleaning the headlamps, please observe the following:
> Do not wipe dry (this causes
scratches) and never use abrasives or strong solvents to clean the covers > Remove dirt and contamination (such as insects) by soaking with BMW Car Shampoo and then rinsing with plenty of water
> Always use a deicer spray to remove
accumulated ice and snow – never use a scraper.<
138nLamps and bulbs
Position lamps 5 watt bulb 1. Using your fingertip, press forward
on the rear edge of the lamp (arrow) and remove
2. Turn the bulb holder with the bulb to the right and remove it from the lamp
3. Pull the bulb out of the socket and
Front turn signals 21 watt bulb 1. Turn the bulb holder with the bulb to
the left and remove toward the rear
2. Applying light pressure, turn the bulb to the left. Remove and exchange the bulb
3. Insert the bulb holder and turn to the
Side turn signals 5 watt bulb 1. Use finger pressure against the front
edge of the lamp (arrow) to press it toward the rear for removal
2. Turn the bulb holder with the bulb to the right and remove it from the lamp
3. Pull the bulb out of the socket and
replace
4. Install in the reverse order.
right as far as possible.
replace
4. Install in the reverse order.
Lamps and bulbs
139n
Z3 roadster
Z3 roadster
Front fog lamps* H1 bulb, 55 watts 1. Unclip the plastic cover (on the
inside of the lamp) with a screwdriver 2. Loosen two screws, tilt the fog lamp
outward and remove it
3. Release the plastic cap on the back
of the fog lamp and remove it
4. Remove the plug 5. Detach the wire clamp 6. Replace the bulb 7. Install in the reverse order.
Tail lamp assembly – Z3 roadster Tail lamp, side marker lamps: 5 watt bulbs Remaining bulbs: 21 watt 1 Turn signal
indicator
2 Brake lamp 3 Backup lamp 4 Tail lamp, reflector 5 Side marker lamp
yellow or white red white red red
1. Open the quick-release fastener
(arrow) and remove the cover
2. Turn the corresponding bulb holder
to the left and remove it
3. Press gently while turning the defec- tive bulb to the left. Remove the bulb and replace it
4. Insert the bulb holder and turn to the
right as far as possible
5. Secure the cover.
140nLamps and bulbs
Z3 coupe
Z3 coupe
Z3 coupe
Tail lamp assembly – Z3 coupe Tail lamp, side marker lamp: 5 watt bulbs Remaining bulbs: 21 watt 1 Turn signal
indicator
2 Backup lamp 3 Tail lamp, reflector 4 Brake lamp 5 Side marker lamps
yellow or white white red red red
1. Lift up the luggage compartment
4. Turn the corresponding bulb holder
floor mat
2. To loosen, turn the mounting clips
(arrows) of the right-hand trim panel on the rear wall of the luggage compartment approx. f turn with a coin or screwdriver
3. Pull out the clips and remove the trim
panel
to the left (arrow) and remove it
5. Press gently while turning the defec- tive bulb to the left. Remove the bulb and replace it
6. Insert the bulb holder and turn to the
right as far as possible
Side marker lamps: Pull the bulb holder out of the tail lamp assembly toward the front. 7. Reinstall the trim panel in the oppo-
site order: Insert the clips and turn them approx. f turn to secure them.
Lamps and bulbs
141n
Z3 roadster
Z3 coupe
Center (high-mount) brake lamp – Z3 roadster In the event of a malfunction, please consult your BMW center.
Center (high-mount) brake lamp – Z3 coupe In the event of a malfunction, please consult your BMW center.
License plate lamps 5 watt bulb 1. Press the lamp to the left and remove
it
2. Turn the bulb holder with the bulb to
the left and remove it from the lamp 3. Pull the bulb out of the bulb socket
and replace
4. Install in the reverse order.
142nLamps and bulbs
Interior lamp – Z3 roadster 10 watt bulb 1. Use a screwdriver to press out the
lens at the left recess
Interior lamps – Z3 coupe Front: 15 watt bulb 1. Use a screwdriver to press out the
2. Pull the bulb out of the contact lugs.
lamp at the left recess
When reinstalling the lens, first position it on the left, then snap it
into place.<
Luggage compartment lamp – Z3 roadster 5 watt bulb The lamp is located above in the luggage compartment. 1. Use a screwdriver to pry out the
lamp
2. Pull the bulb out of the contact lugs.
2. Press back the plastic tab on the reflector, open the reflector and replace the bulb.
Rear: 10 watt bulb 1. Use a screwdriver to press out the
lamp at the side recess
2. Press back the plastic tab on the reflector, open the reflector and replace the bulb.
Reading lamps – Z3 coupe 10 watt bulbs 1. Use a screwdriver to press out the
lamp at the left recess
2. Press gently while turning the defec- tive bulb to the left. Remove the bulb and replace it.
Master key with battery lamp
143n
Return used batteries to a recycling point or to your BMW
center.<
If light intensity drops, renew the battery to safeguard against acid escaping.
Battery change 1. Remove the cover on the back of the
key with a screwdriver
2. Insert a new battery (refer to the illus-
tration) of the same type (CR 2025) so that it touches the contacts
3. Snap the cover into place and apply
uniform pressure to seat it.
144nRemote control
Changing battery Renew when the LED no longer lights up when a button is pressed and it is not possible to lock the vehicle using the remote key. Install only a battery of the specification (CR 2016) indicated in the battery compartment and make sure that the battery is installed in the correct posi- tion. 1. Use a screwdriver to lift the cover at
the recess (arrow)
2. Loosen the two screws (arrows) and
remove the cover.
The battery type and its installation position are stamped into the base of the battery compartment.
Return used batteries to a recy- cling point or your BMW center.<
New master key with remote control If you place a new master key with remote control into service (either a replacement or an additional key), it must be initialized together with all existing master keys (with remote control): 1. Have all existing master keys with
remote control as well as the spare- or ignition key present, refer to page 30
2. Enter the vehicle and close the doors 3. Briefly turn the spare key 2 or the ignition key 3 (max. 5 seconds) to position 1 in the steering lock, then return it to position 0
Turn each new master key into ignition position 2 (ignition
switched on) and back again to allow the electronic vehicle immobilizer (refer to page 31) to recognize the new key. To prevent unauthorized use of the master key, surrender only the door and ignition key 3 or the spare key 2 (refer to page 30) for valet parking, for instance.<
Remote control
4. Press and hold down button 1 (see
