Login- Download PDF Manual
-
Depending on the selected temperature and outside influences, the air is directed to the windshield, side windows, upper body, and into the footwell.
Climate control
Controls
The cooling function, refer to page 135, is switched on automatically with the AUTO pro‐ gram. Temperature
Turn the wheel to set the desired temperature.
The automatic climate control reaches this tem‐ perature as quickly as possible, if necessary by increasing the cooling or heating output, and then keeps it constant. Avoid rapidly switching between different tem‐ perature settings. The automatic climate control will not have sufficient time to adjust the set temperature. Cooling function The passenger compartment can only be cooled with the engine running.
Press the button. The air is cooled and dehumidified and
– depending on the temperature setting – warmed again. Depending on the weather, the windshield may fog up briefly when the engine is started. The cooling function is switched on automati‐ cally with the AUTO program. When using the automatic climate control, con‐ densation water, refer to page 158, develops that exits underneath the vehicle. Recirculated-air mode You can respond to unpleasant odors or pollu‐ tants in the immediate environment by tempo‐ rarily suspending the supply of outside air. The system then recirculates the air currently within the vehicle.
Press the button repeatedly to select an operating mode:
Online Edition for Part no. 01 40 2 608 633 - 11 09 490
135
Controls
Climate control
▷ LED off: outside air flows in continuously. ▷ LED on, recirculated-air mode: the supply of
outside air into the vehicle is permanently blocked.
If the windows fog over, switch off recirculated- air mode and increase the air volume, if neces‐ sary.
Continuous recirculated-air mode The recirculated-air mode should not be used for an extended period of time, as the air quality inside the vehicle deteriorates steadily.◀
Switching the system on/off Switching off
Press the left button at the minimum speed.
Switching on Press any button except the seat heating but‐ tons. Microfilter, recirculated air filter The microfilter removes dust and pollen from the incoming air. The recirculated-air filter removes dust from the interior air in recirculated-air mode. These filters should be replaced during sched‐ uled maintenance of your vehicle., refer to page 277
Automatic climate control with enhanced features
1 Seat heating, left 47
2 Temperature, left 3 AUTO program4 Display 5 Maximum cooling 6 Temperature, right
136
Online Edition for Part no. 01 40 2 608 633 - 11 09 490
Climate control
Controls
7 Seat heating, right 47
8 Cooling function 9 Automatic recirculated-air control/recircu‐lated-air mode
10 Air distribution, right 11 Air flow, AUTO intensity
12 Air distribution, left 13 Rear window defroster 14 Interior temperature sensor — always keep
15 Defrosting windows and removing conden‐
clear
sation
Climate control functions in detail Temperature
Turn the wheel to set the desired temperature.
The automatic climate control reaches this tem‐ perature as quickly as possible, if necessary by increasing the cooling or heating output, and then keeps it constant. Avoid rapidly switching between different tem‐ perature settings. The automatic climate control will not have sufficient time to adjust the set temperature. AUTO program
Press the button. Air volume, air distribution, and tem‐
perature are controlled automatically. Depending on the selected temperature, AUTO intensity, and outside influences, the air is di‐ rected to the windshield, side windows, upper body, and into the footwell. The cooling function, refer to page 137, is switched on automatically with the AUTO pro‐ gram. At the same time, a condensation sensor con‐ trols the program so as to prevent window con‐ densation as much as possible.
Intensity of the AUTO program With the AUTO program switched on, automatic control of the air volume and air distribution can be adjusted.
Press the left or right side of the button: decrease or increase the intensity.
The selected intensity is shown on the display of the automatic climate control. Maximum cooling
Press the button. The system is set to the lowest tem‐
perature, maximum air flow and recirculated-air mode. Air flows out of the vents for the upper body re‐ gion. Open them for this purpose. The air is cooled fastest when the engine is run‐ ning. The air flow can be adjusted when the program is active. Cooling function The passenger compartment can only be cooled with the engine running.
Press the button. The air is cooled and dehumidified and
– depending on the temperature setting – warmed again. Depending on the weather, the windshield may fog up briefly when the engine is started. The cooling function is switched on automati‐ cally with the AUTO program.
Online Edition for Part no. 01 40 2 608 633 - 11 09 490
137
Controls
Climate control
When using the automatic climate control, con‐ densation water, refer to page 158, develops that exits underneath the vehicle. Automatic recirculated-air control/ recirculated-air mode You can respond to unpleasant odors or pollu‐ tants in the immediate environment by tempo‐ rarily suspending the supply of outside air. The system then recirculates the air currently within the vehicle.
Press the button repeatedly to select an operating mode:
▷ LEDs off: outside air flows in continuously. ▷ Left LED on, automatic recirculated-air con‐ trol: a sensor detects pollutants in the out‐ side air and controls the shutoff automati‐ cally.
▷ Right LED on, recirculated-air mode: the
supply of outside air into the vehicle is per‐ manently blocked.
If the windows are fogged over, switch off the recirculated-air mode and press the AUTO but‐ ton to utilize the condensation sensor. Make sure that air can flow onto the windshield.
Continuous recirculated-air mode The recirculated-air mode should not be used for an extended period of time, as the air quality inside the vehicle deteriorates steadily.◀
Manual air distribution
Press the button repeatedly to select a program:
▷ Upper body region. ▷ Upper body region and footwell. ▷ Footwell. ▷ Windows and footwell: driver's side only. ▷ Windows, upper body region and footwell:
driver's side only.
If the windows are fogged over, press the AUTO button to utilize the condensation sensor.
Air volume, manual To be able to manually adjust the air volume, switch off the AUTO program first.
Press the left or right side of the button: decrease or increase air volume.
The selected air volume is shown on the display of the automatic climate control. The air volume of the automatic climate control may be reduced automatically to save battery power. Rear window defroster Press the button. The rear window defroster switches off
automatically after a certain period of time.
Defrosting windows and removing condensation
Press the button. Ice and condensation are quickly re‐ moved from the windshield and the front side windows. The air volume can be adjusted when the pro‐ gram is active. If the windows are fogged over, additionally switch on the cooling function or press the AUTO button to utilize the condensation sensor. Switching the system on/off Switching off
Press the left button at the minimum speed.
Switching on Press any button except the seat heating but‐ tons.
138
Online Edition for Part no. 01 40 2 608 633 - 11 09 490
Climate control
Controls
Ventilation in the rear
▷ Thumbwheel for opening and closing the
vents continuously, arrow 1.
▷ Thumbwheel to vary the temperature, ar‐
row 2. Toward blue: colder. Toward red: warmer.
▷ Lever for changing the air flow direction, ar‐
row 3.
Parked-car ventilation The concept The parked-car ventilation ventilates the vehicle interior and lowers its temperature, if necessary. The system can be switched on and off at any external temperature, either directly or by using two preset switch-on times. It remains switched on for 30 minutes. Open the vents to allow air to flow out. Operation can be performed via iDrive. Switching on/off directly 1. "Settings" 2. "Climate" 3. "Activate parked-car vent."
The symbol on the automatic climate control
flashes if the system is switched on.
Microfilter/activated-charcoal filter, recirculated-air filter The microfilter removes dust and pollen from the incoming air. The activated-charcoal filter removes gaseous pollutants from the outside air that enters the vehicle. The recirculated-air filter removes dust from the interior air in recirculated-air mode. These filters should be replaced during sched‐ uled maintenance, refer to page 277, of your vehicle.
Ventilation Front ventilation
▷ Lever for changing the air flow direction, ar‐
row 1.
▷ Thumbwheels for opening and closing the
vents continuously, arrows 2.
▷ Thumbwheel to vary the temperature, ar‐
row 3. Toward blue: colder. Toward red: warmer.
Adjusting the ventilation ▷ Ventilation for cooling:
Adjust the vent to direct the air in your di‐ rection, e.g., if the vehicle interior is hot from the sun.
▷ Draft-free ventilation:
Adjust the vent to let the air flow past you.
Online Edition for Part no. 01 40 2 608 633 - 11 09 490
139
Controls
Climate control
Preselecting the switch-on time 1. "Settings" 2. "Climate" 3. "Timer 1:" or "Timer 2:" 4. Set the desired time. Activating the switch-on time 1. "Settings" 2. "Climate" 3. "Activate Timer 1" or "Activate Timer 2"
The symbol on the automatic climate control lights up when the switch-on time is activated. The symbol on the automatic climate control flashes when the system has been switched on. The system will only be switched on within the next 24 hours. After that, it needs to reactivated.
140
Online Edition for Part no. 01 40 2 608 633 - 11 09 490
Interior equipment Vehicle equipment All standard, country-specific and optional equipment that is offered in the model series is described in this chapter. Therefore, equipment is also described that is not available in a vehicle, e. g., because of the selected optional equip‐ ment or country variant. This also applies for safety-related functions and systems.
Integrated universal remote control The concept The integrated universal remote control can op‐ erate up to 3 functions of remote-controlled sys‐ tems such as garage door drives or lighting sys‐ tems. The integrated universal remote control replaces up to 3 different hand-held transmit‐ ters. To operate the remote control, the buttons on the interior rearview mirror must be program‐ med with the desired functions. The hand-held transmitter for the particular system is required in order to program the remote control.
During programming During programming and before activat‐ ing a device using the integrated universal re‐ mote control, ensure that there are no people, animals, or objects in the range of movement of the remote-controlled device; otherwise, there is a risk of injury or damage. Also follow the safety instructions of the hand- held transmitter.◀ Before selling the vehicle, delete the stored functions for the sake of security. Compatibility
If this symbol is printed on the packaging or in the instructions of the system to be controlled, the system is generally com‐
Interior equipment
Controls
patible with the integrated universal remote control. If you have any questions, please contact: ▷ Your service center. ▷ www.homelink.com on the Internet. HomeLink is a registered trademark of Johnson Controls, Inc. Controls on the interior rearview mirror
▷ LED, arrow 1. ▷ Buttons, arrow 2. ▷ The hand-held transmitter, arrow 3, is re‐
quired for programming.
Programming General information 1. Switch on the ignition. 2.
Initial setup: Press and hold the left and right button on the interior rearview mirror simultaneously for approximately 20 seconds until the LED on the interior rearview mirror flashes. This erases all programming of the buttons on the interior rearview mirror.
3. Hold the hand-held transmitter for the sys‐ tem to be controlled approx. 1 to 3 in/2.5 to 8 cm away from the buttons on the interior rearview mirror. The required distance de‐ pends on the manual transmitter.
Online Edition for Part no. 01 40 2 608 633 - 11 09 490
141
Controls
Interior equipment
4. Simultaneously press and hold the button of the desired function on the hand-held trans‐ mitter and the button to be programmed on the interior rearview mirror. The LED on the interior rearview mirror will begin flashing slowly.
5. Release both buttons as soon as the LED
flashes more rapidly. When the LED flashes faster, this indicates that the button on the interior rearview mirror has been program‐ med. If the LED does not flash faster after at least 60 seconds, change the distance between the interior rearview mirror and the hand- held transmitter and repeat the step. Several more attempts at different distances may be necessary. Wait at least 15 seconds be‐ tween attempts. Canada: if programming with the hand-held transmitter was interrupted, hold down the interior rearview mirror button and repeat‐ edly press and release the hand-held trans‐ mitter button for 2 seconds.
6. To program other functions on other but‐
tons, repeat steps 3 to 5.
The systems can be controlled using the interior rearview mirror buttons. Special feature of the alternating-code wireless system If you are unable to operate the system after re‐ peated programming, please check if the sys‐ tem to be controlled features an alternating- code system. Read the system's operating manual, or press the programmed button on the interior rearview mirror longer. If the LED on the interior rearview mirror starts flashing rapidly and then stays lit constantly for 2 seconds, the system features an alternating-code system. Flashing and con‐ tinuous illumination of the LED will repeat for approximately 20 seconds.
For systems with an alternating-code system, the integrated universal remote control and the system also have to be synchronized. Please read the operating manual of the system being set up for information on how to syn‐ chronize the system. Synchronizing is easier with the aid of a second person. To synchronize: 1. Park the vehicle within range of the remote-
controlled system.
2. Program the relevant button on the interior
rearview mirror as described.
3. Locate and press the synchronizing button on the system being programmed. You have approx. 30 seconds for the next step.
4. Hold down the programmed button on the interior rearview mirror for approximately 3 seconds and then release it. If necessary, repeat this work step up to three times in or‐ der to finish synchronization. Once synchro‐ nization is complete, the programmed func‐ tion will be carried out.
Reprogramming individual buttons 1. Switch on the ignition. 2. Press and hold the interior rearview mirror
button to be programmed.
3. As soon as the interior rearview mirror LED
starts flashing slowly, hold the hand-held transmitter for the system to be controlled approx. 1 to 3 in/2.5 to 8 cm away from the buttons on the interior rearview mirror. The required distance depends on the manual transmitter.
4. Likewise, press and hold the button of the desired function on the hand-held transmit‐ ter.
5. Release both buttons as soon as the interior
rearview mirror LED flashes more rapidly. When the LED flashes faster, this indicates that the button on the interior rearview mir‐
142
Online Edition for Part no. 01 40 2 608 633 - 11 09 490
ror has been programmed. The system can then be controlled by the button on the in‐ terior rearview mirror. If the LED does not flash faster after at least 60 seconds, change the distance and repeat the step. Several more attempts at different distances may be necessary. Wait at least 15 seconds between attempts. Canada: if programming with the hand-held transmitter was interrupted, hold down the interior rearview mirror button and repeat‐ edly press and release the hand-held trans‐ mitter button for 2 seconds.
Controls
Before operation Before operating a system using the
integrated universal remote control, ensure that there are no people, animals, or objects within the range of movement of the remote-controlled system; otherwise, there is a risk of injury or damage. Also follow the safety instructions of the hand- held transmitter.◀ The system, such as the garage door, can be operated using the button on the interior rear‐ view mirror while the engine is running or when the ignition is started. To do this, hold down the button within receiving range of the system until the function is activated. The interior rearview mirror LED stays lit while the wireless signal is being transmitted. Deleting stored functions Press and hold the left and right button on the interior rearview mirror simultaneously for ap‐ proximately 20 seconds until the LED flashes rapidly. All stored functions are deleted. The functions cannot be deleted individually.
Interior equipment
Controls
Digital compass At a glance
1 Control button 2 Mirror display
Mirror display The point of the compass is displayed in the mirror when driving straight. Operating concept Various functions can be called up by pressing the control button with a pointed object, such as the tip of a ballpoint pen or similar object. The following setting options are displayed in suc‐ cession, depending on how long the control but‐ ton is pressed: ▷ Pressed briefly: turns display on/off. ▷ 3 to 6 seconds: compass zone setting. ▷ 6 to 9 seconds: compass calibration. ▷ 9 to 12 seconds: left/right-hand steering
setting.
▷ 12 to 15 seconds: language setting. Setting the compass zones Sets the particular compass zones on the vehi‐ cle so that the compass operates correctly; refer to World map with compass zones.
Online Edition for Part no. 01 40 2 608 633 - 11 09 490
143
Controls
Interior equipment
World map with compass zones
Procedure 1. Press and hold the control button for approx. 3 to 4 seconds. The number of the set com‐ pass zone appears in the mirror.
2. To change the zone setting, press the con‐ trol button quickly and repeatedly until the number of the compass zone corresponding to your location appears in the mirror.
The set zone is stored automatically. The com‐ pass is ready for use again after approximately 10 seconds. Calibrating the digital compass The digital compass must be calibrated in the event of the following: ▷ The wrong point of the compass is dis‐
played.
▷ The point of the compass displayed does not change despite changing the direction of travel.
▷ Not all points of the compass are displayed.
Procedure 1. Make sure that there are no large metallic
objects or overhead power lines near the ve‐ hicle and that there is sufficient room to drive around in a circle.
2. Set the currently applicable compass zone. 3. Press and hold the control button for approx. 6 to 7 seconds so that "C" appears on the display. Next, drive in a complete circle at least once at a speed of no more than 4 mph/ 7 km/h. If calibration is successful, the "C" is replaced by the points of the compass.
Left/right-hand steering The digital compass is already set for right or left-hand steering at the factory. Setting the language Press and hold the control button for approx. 12
to 13 seconds. Briefly press the control button again to switch between English "E" and Ger‐ man "O".144
Online Edition for Part no. 01 40 2 608 633 - 11 09 490
Interior equipment
Controls
Push in the lighter. The lighter can be removed as soon as it pops back out.
Connecting electrical devices Sockets The lighter socket can be used as a socket for electrical equipment while the engine is running or when the ignition is switched on. The total load of all sockets must not exceed 140 watts at 12 volts. Do not damage the socket by using unsuitable connectors. Front center console
The setting is stored automatically after approx‐ imately 10 seconds.
Ashtray/cigarette lighter Ashtray Opening
Raise cover.
Emptying Take out the insert. Lighter
Danger of burns Only hold the hot lighter by its knob; oth‐ erwise, there is the danger of getting burned. Switch off the ignition and take the remote con‐ trol with you when leaving the vehicle so that children cannot use the lighter and burn them‐ selves.◀
Raise the cap and remove the cover or cigarette lighter.
In the front passenger footwell
The lighter is located next to the ashtray.
Socket is located below the glove compartment.
Online Edition for Part no. 01 40 2 608 633 - 11 09 490
145
Locking the backrest Before carrying persons in the rear, en‐
gage and thereby lock the backrests, or the re‐ straining effect of the safety belts during an ac‐ cident may be limited.◀
Retract the head restraints if necessary before backrests are folded down
With folding head restraints, fold in the head re‐ straints before folding down the backrests, or damage may result.◀
Opening 1. Unlock the belt lock of the center safety belt
in the rear using the latch plate of another safety belt. Insert the latch plate at the end of the belt into the specially designated fixture on the rear window shelf.
2.
3. Push the corresponding head restraint
down as far as it will go.
Controls
Interior equipment
Rear center console
Remove cover.
In the cargo area
The socket is located on the left side in the cargo area.
Through-loading system General information The cargo area can be enlarged by folding down the rear seat backrest. The rear seat backrest is divided at a ratio of 40– 20–40.
Danger of pinching Before folding down the rear seat backr‐ ests, ensure that the area of movement of the backrests is clear. In particular, ensure that no one is located in the area of movement and that no one reaches into the area of movement of the rear seat backrests when the middle section is folded down. Otherwise, injury or damage may result.◀
146
Online Edition for Part no. 01 40 2 608 633 - 11 09 490
4. Pull the corresponding lever in the cargo
area to release the rear seat backrest.
Interior equipment
Controls
Folding down the middle section 1. Fold in the middle head restraint. 2. Reach into the recess and pull the middle
section forward.
5. The unlocked rear seat backrest moves for‐ ward slightly. Fold the backrest forward by the head restraint.
Closing 1. Return the rear seat backrest to the upright
seating position and engage it.
Ensure that the lock is securely en‐ gaged
When folding back the backrest, be sure that it locks in place securely. If it is not properly engaged, transported cargo could enter the passenger compartment during braking or evasive maneuvers and endanger the vehi‐ cle occupants.◀
2. Release the latch plate from the fixture on the rear window shelf and insert it into the belt lock of the center safety belt. Make sure you hear the latch plate engage.
To secure cargo, refer to page 160, with nets or draw straps, the cargo area is fitted with lashing eyes.
Online Edition for Part no. 01 40 2 608 633 - 11 09 490
147
Controls
Storage compartments
Storage compartments Vehicle equipment All standard, country-specific and optional equipment that is offered in the model series is described in this chapter. Therefore, equipment is also described that is not available in a vehicle, e. g., because of the selected optional equip‐ ment or country variant. This also applies for safety-related functions and systems.
▷ Storage compartment in the rear center
console, refer to page 150.
Glove compartment Front passenger side Opening
Notes
No loose objects in the passenger com‐ partment
Do not stow any objects in the passenger com‐ partment without securing them; otherwise, they may present a danger to occupants for in‐ stance during braking and avoidance maneu‐ vers.◀
Do not place anti-slip mats on the dash‐ board
Do not place anti-slip mats on the dashboard. The mat materials could damage the dash‐ board.◀
Storage compartments The following storage compartments are avail‐ able in the vehicle interior: ▷ Glove compartment on the front passenger
side, refer to page 148.
▷ Without Smoker's package: Front storage compartment, in front of the cupholders, re‐ fer to page 149.
▷ Storage compartment in the front center
armrest, refer to page 149.
▷ Compartments in the doors, refer to
page 149.
▷ Nets on the backrests of the front seats.
Pull the handle. The light in the glove compartment switches on. The net in the glove compartment is provided for stowing the storage tray for the cupholder, refer to page 150.
Close the glove compartment again im‐ mediately
Close the glove compartment immediately after use while driving; otherwise, injury may occur during accidents.◀
Closing Fold up the cover. Locking The glove compartment can be locked with an integrated key to separately secure the trunk lid, refer to page 38, for example. After the glove compartment is locked, the re‐ mote control can be handed over, such as at a hotel, without the integrated key, refer to page 30.
148
Online Edition for Part no. 01 40 2 608 633 - 11 09 490
This prevents access to the glove compartment and to the cargo area. USB interface for data transfer
Connection for importing and exporting data on USB devices, e.g.: ▷ Personal Profile settings, refer to page 33. ▷ Music collection, refer to page 205. Observe the following when connecting: ▷ Do not use force when plugging the con‐
nector into the USB interface.
▷ Do not connect devices such as fans or
lamps to the USB interface.
▷ Do not connect USB hard drives. ▷ Do not use the USB interface to recharge
external devices.
Front storage compartment
Storage compartments
Controls
Compartments in the doors
Do not stow any breakable objects Do not store any breakable objects, e. g. glass bottles, in the compartments, or there is an increased risk of injury in the event of an ac‐ cident.◀
Center armrest Front A storage compartment is located in the center armrest between the front seats. Opening
Raise the center arm rest.
Repositioning Center armrest can be pushed in the longitudi‐ nal direction. It engages in the end positions.
Raise the lid to open it.
Online Edition for Part no. 01 40 2 608 633 - 11 09 490
149
Controls
Storage compartments
Connection for an external audio device
Front
This can be used to connect an external audio device, such as an MP3 player. ▷ AUX-IN port, refer to page 210. ▷ USB audio interface, refer to page 210.
Storage compartment in the rear Storage compartment is located in the rear cen‐ ter console.
Cupholders Notes
Shatter-proof containers and no hot drinks
Use light and shatter-proof containers and do not transport hot drinks. Otherwise, there is the increased danger of injury in an accident.◀
Unsuitable containers Do not forcefully push unsuitable contain‐ ers into the cupholders. This may result in dam‐ age.◀
Storage tray for front cupholders The cupholder with the storage tray can be used for additional storage. To do this, place the stor‐ age tray in the cupholder. Only use the storage tray for small objects, such as keys or the remote control. When not in use, stow the storage tray in the glove compartment net. Insert the storage tray into the net so that the top surface faces up. Note the trapezoidal shape of the net and tray. Rear In the center armrest.
Pull the center armrest forward at the strap. To open: press the button. To close: push both covers back in, one after the other.
Pushing back the covers Push back the covers before folding up the center armrest; otherwise, the cupholder could become damaged.◀
150
Online Edition for Part no. 01 40 2 608 633 - 11 09 490
Clothes hooks The clothes hooks are located in the grab han‐ dles in the rear.
Do not obstruct view When suspending clothing from the
hooks, ensure that it will not obstruct the driver's vision.◀
No heavy objects Do not hang heavy objects from the hooks;
otherwise, they may present a danger to pas‐ sengers during braking and evasive maneu‐ vers.◀
Storage compartments in the cargo area Left storage compartment A storage compartment is located on the left side. Net Small objects can be stowed in the net on the left side. Right storage compartment Located on the right side is a storage compart‐ ment for the onboard vehicle tool kit, refer to page 279, and first aid kit, refer to page 291.
Storage compartments
Controls
Hooks/multi-function hook
A multi-function hook is located on each side of the cargo area. The multi-function hooks can be loaded up to a max. of 8.8 lbs/4 kg.
Light and suitable objects only Only hang light bags or suitable objects
from the holders. Otherwise, there is a danger of objects flying about during braking and evasive maneuvers. Only transport heavy luggage in the trunk if it has been appropriately secured.◀
Retaining strap A retaining strap is available on the right side trim for fastening small objects. Lashing eyes in the cargo area To secure the cargo, refer to page 160, there are four lashing eyes in the cargo area. Floor net The floor net can also be used to Secure the load, refer to page 160, and to store small parts. Storage compartment under cargo floor panel
Maximum load To avoid damage to the vehicle, do not ex‐ ceed a maximum permitted load of 44 lbs/20 kg in the storage compartment under the cargo floor panel.◀
Online Edition for Part no. 01 40 2 608 633 - 11 09 490
151
Controls
Storage compartments
Raise the cargo floor panel, arrow 1, and latch at top, if necessary, arrow 2.
Partitioning the compartment The compartment can be divided using an at‐ tachable partition.
152
Online Edition for Part no. 01 40 2 608 633 - 11 09 490
Storage compartments
Controls
Online Edition for Part no. 01 40 2 608 633 - 11 09 490
153
Online Edition for Part no. 01 40 2 608 633 - 11 09 490
Driving tips
This chapter provides you with information useful in dealing with specific driving and operating modes.
Online Edition for Part no. 01 40 2 608 633 - 11 09 490
Driving tips
Things to remember when driving
Things to remember when driving Vehicle equipment All standard, country-specific and optional equipment that is offered in the model series is described in this chapter. Therefore, equipment is also described that is not available in a vehicle, e. g., because of the selected optional equip‐ ment or country variant. This also applies for safety-related functions and systems.
Drive conservatively for the first 200 miles/ 300 km. Brake system Brakes require an initial break-in period of ap‐ prox. 300 miles/500 km to achieve optimized contact and wear patterns between brake pads and discs. Drive moderately during this break-in period. Following part replacement The same breaking in procedures should be ob‐ served if any of the components mentioned above have to be renewed in the course of the vehicle's operating life.
General driving notes Closing the trunk lid
Drive with the trunk lid closed Only drive with the tailgate closed; other‐ wise, in the event of an accident or braking or evasive maneuvers, passengers or other road users may be injured or the vehicle may be dam‐ aged. In addition, exhaust fumes may enter the passenger compartment.◀ If driving with the tailgate open cannot be avoided: ▷ Close all windows and the glass sunroof. ▷ Greatly increase the blower speed. ▷ Drive moderately. Hot exhaust system Hot exhaust system High temperatures are generated in the
exhaust system.
Breaking-in period General information Moving parts need to be broken in to adjust to each other. The following instructions will help achieve a long vehicle life and good economy. Engine and differential Always obey the official speed limit. Up to 1,200 miles/2,000 km Do not exceed the maximum engine and road speed: ▷ For gasoline engine, 4,500 rpm and
100 mph/160 km/h.
Avoid full-throttle operation and use of the transmission's kickdown mode for the initial miles. From 1,200 miles/2,000 km The engine and vehicle speed can gradually be increased. Tires Due to technical factors associated with their manufacture, tires do not achieve their full trac‐ tion potential until after an initial breaking-in pe‐ riod.
156
Online Edition for Part no. 01 40 2 608 633 - 11 09 490
Things to remember when driving
Driving tips
Do not remove the heat shields installed and never apply undercoating to them. When driv‐ ing, standing at idle and while parking, take care to avoid possible contact between the hot ex‐ haust system and any highly flammable materi‐ als such as hay, leaves, grass, etc. Such contact could lead to a fire, and with it the risk of serious personal injury as well as property damage. Do not touch hot exhaust pipes; otherwise, there is the danger of getting burned.◀
Mobile communication devices in the vehicle
Mobile communication devices in the ve‐ hicle
It is advised that you do not use mobile commu‐ nication devices, e.g., mobile phones, inside the vehicle without connecting them directly to the external antenna. Otherwise, the vehicle elec‐ tronics and mobile communication devices can interfere with each other. In addition, there is no assurance that the radiation generated during transmission will be discharged from the vehicle interior.◀
Hydroplaning On wet or slushy roads, a wedge of water can form between the tires and road surface. This phenomenon is referred to as hydroplan‐ ing. It is characterized by a partial or complete loss of contact between the tires and the road surface, ultimately undermining your ability to steer and brake the vehicle.
Hydroplaning When driving on wet or slushy roads, re‐
duce your speed to prevent hydroplaning.◀
Driving through water Drive though calm water only if it is not deeper than 9.8 inches/25 cm and at this height, no faster than walking speed, up to 6 mph/10 km/h.
Adhere to water depth and speed limita‐ tions
Do not exceed this water depth and walking speed; otherwise, the vehicle's engine, the elec‐ trical systems and the transmission may be damaged.◀
Braking safely Your vehicle is equipped with ABS as a standard feature. Applying the brakes fully is the most effective way of braking in situations when this is neces‐ sary. The vehicle maintains steering responsiveness. You can still avoid any obstacles with a minimum of steering effort. Pulsation of the brake pedal and sounds from the hydraulic circuits indicate that ABS is in its active mode. Objects in the area around the pedals No objects in the area around the pedals Keep floor mats, carpets, and any other objects out of the area of motion of the pedals; otherwise, the function of the pedals could be impeded while driving Do not place additional floor mats over existing mats or other objects. Only use floor mats that have been approved for the vehicle and can be properly fixed in place. Ensure that the floor mats are securely fastened again after they were removed for cleaning, for example.◀
Driving in wet conditions When roads are wet or there is heavy rain, briefly exert gentle pressure on the brake pedal every few miles. Ensure that this action does not endanger other road users. The heat generated in this process helps dry the brake discs and pads.
Online Edition for Part no. 01 40 2 608 633 - 11 09 490
157
Driving tips
Things to remember when driving
Therefore, traces of condensed water under the vehicle are normal.
In this way braking efficiency will be available when you need it. Hills Drive long or steep downhill gradients in the gear in which the least braking is required. Otherwise, the brake system may overheat, resulting in a reduction in the brake system efficiency. Automatic transmission: You can increase the engine's braking effect by shifting down in the manual mode of the auto‐ matic transmission.
Avoid load on the brakes Avoid placing excessive load on the brake system. Light but consistent brake pressure can lead to high temperatures, brake wear and pos‐ sibly even brake failure.◀
Do not drive in neutral Do not drive in neutral or with the engine stopped, as doing so disables engine braking. In addition, steering and brake assist is unavailable with the engine stopped.◀
Brake disc corrosion Corrosion on the brake discs and contamination on the brake pads are furthered by: ▷ Low mileage. ▷ Extended periods when the vehicle is not
used at all.
▷ Infrequent use of the brakes. Corrosion occurs when the minimum pressure that must be exerted by the pads during brake applications to clean the discs is not reached. Should corrosion form on the brake discs, the brakes will tend to respond with a pulsating ef‐ fect that generally cannot be corrected. Condensation under the parked vehicle When using the automatic climate control, con‐ densation water develops that exits underneath the vehicle.
158
Online Edition for Part no. 01 40 2 608 633 - 11 09 490
Loading Vehicle equipment All standard, country-specific and optional equipment that is offered in the model series is described in this chapter. Therefore, equipment is also described that is not available in a vehicle, e. g., because of the selected optional equip‐ ment or country variant. This also applies for safety-related functions and systems.
General information Overloading the vehicle To avoid exceeding the approved carrying capacity of the tires, never overload the vehicle. Overloading can lead to overheating and in‐ creases the rate at which damage develops in‐ side the tires. This could result in a sudden loss of tire inflation pressure.◀ No fluids in the trunk Make sure that fluids do not leak into the trunk; otherwise, the vehicle may be damaged.◀
Determining the load limit
Loading
Driving tips
hicle and unstable driving situations may result.
2. Determine the combined weight of the
driver and passengers that will be riding in your vehicle.
3. Subtract the combined weight of the driver and passengers from XXX kilograms or YYY pounds.
4. The resulting figure equals the available
amount of cargo and luggage load capacity. For example, if the YYY amount equals 1,000 lbs and there will be four 150 lbs pas‐ sengers in your vehicle, the amount of avail‐ able cargo and luggage load capacity is 400 lbs: 1,000 lbs minus 600 lbs = 400 lbs. 5. Determine the combined weight of luggage and cargo being loaded on the vehicle. That weight may not safely exceed the available cargo and luggage load capacity calculated in Step 4.
Load
The maximum load is the sum of the weight of the occupants and the cargo. The greater the weight of the occupants, the less cargo that can be transported.
1. Locate the following statement on your ve‐
hicle’s placard: ▷ The combined weight of occupants and
cargo should never exceed XXX kg or YYY lbs. Otherwise, damage to the ve‐
Online Edition for Part no. 01 40 2 608 633 - 11 09 490
159
Driving tips
Loading
Stowing cargo
Floor net The floor net can also be used to Secure the load and to store small parts.
▷ Heavy cargo: stow as far forward and as low as possible, ideally directly behind the cargo area separating wall.
▷ Very heavy cargo: when the rear seat is not occupied, secure each of the outer safety belts in the opposite buckle.
▷ Cover sharp edges and corners. ▷ If necessary, fold down the rear backrests to
stow cargo.
▷ Do not stack cargo above the top edge of the
backrests.
▷ Place protective material around any sharp- edged or pointed objects that could bump against the rear window while the vehicle is in motion.
Securing cargo Lashing eyes in the cargo area
To secure the cargo, there are four lashing eyes in the cargo area
Hook the floor net into the fittings in the cargo area floor.
Securing cargo ▷ Smaller and lighter items: secure with re‐ taining straps, the floor net or draw straps. ▷ Larger and heavy objects: secure with cargo
straps.
Attach the cargo straps, retaining straps or draw straps to the lashing eyes in the cargo area.
Securing cargo Always position and secure the cargo as described above; otherwise, it can endanger the car's occupants if sudden braking or swerving becomes necessary. Heavy or hard objects should not be carried loose inside the car; otherwise, they could be thrown around as a result of hard braking, sud‐ den swerves, etc., and endanger the occu‐ pants.◀
Roof-mounted luggage rack Note Roof racks are available as special accessories. Attachment Follow the installation instructions of the roof rack.
160
Online Edition for Part no. 01 40 2 608 633 - 11 09 490
Roof drip rail with flaps
Loading
Driving tips
The anchorage points are located in the roof drip rail above the doors. Fold the cover outward.
Loading Because roof racks raise the vehicle's center of gravity when loaded, they have a major effect on vehicle handling and steering response. Therefore, note the following when loading and driving: ▷ Do not exceed the approved roof/axle loads
and the approved gross vehicle weight.
▷ Distribute the roof load uniformly. ▷ The roof load should not be too large in area. ▷ Always place the heaviest pieces on the bot‐
tom.
▷ Secure the roof luggage firmly, e.g., tie with
ratchet straps.
▷ Drive smoothly. Avoid sudden acceleration and braking maneuvers. Take corners gen‐ tly.
Online Edition for Part no. 01 40 2 608 633 - 11 09 490
161
Driving tips
Saving fuel
Saving fuel Vehicle equipment All standard, country-specific and optional equipment that is offered in the model series is described in this chapter. Therefore, equipment is also described that is not available in a vehicle, e. g., because of the selected optional equip‐ ment or country variant. This also applies for safety-related functions and systems.
General information Your vehicle contains advanced technology for the reduction of fuel consumption and emis‐ sions. Fuel consumption depends on a number of dif‐ ferent factors. The implementation of certain measures, driv‐ ing style and regular maintenance can have an influence on fuel consumption and on the envi‐ ronmental impact.
Remove unnecessary cargo Additional weight increases fuel consumption.
Remove attached parts following use Remove auxiliary mirrors, roof or rear luggage racks which are no longer required following use. Attached parts on the vehicle impair the aero‐ dynamics and increase the fuel consumption.
Close the windows and glass sunroof Driving with the glass sunroof and windows open results in increased air resistance and raises fuel consumption.
Check the tire inflation pressure regularly Check and, if necessary, correct the tire inflation pressure at least twice a month and before start‐ ing on a long trip. Low tire inflation pressure increases rolling re‐ sistance and thus raises fuel consumption and tire wear.
Drive away without delay Do not wait for the engine to warm up while the vehicle remains stationary. Start driving right away, but at moderate engine speeds. This is the fastest way for the cold engine to reach its operating temperature.
Look well ahead when driving Avoid unnecessary acceleration and braking. By maintaining a suitable distance to the vehicle driving ahead of you. Driving smoothly and looking ahead reduces fuel consumption.
Avoid high engine speeds Use 1st gear to get the vehicle in motion. Be‐ ginning with 2nd gear, accelerate rapidly. When accelerating, shift up before reaching high en‐ gine speeds.
162
Online Edition for Part no. 01 40 2 608 633 - 11 09 490
When you reach the desired speed, shift into the highest applicable gear and drive with the en‐ gine speed as low as possible and at a constant speed. As a rule: driving at low engine speeds lowers fuel consumption and reduces wear. The gear shift indicator of your vehicle indicates the most fuel efficient gear.
Use coasting conditions When approaching a red light, take your foot off the accelerator and let the vehicle coast to a halt. On a downhill gradient, take your foot off the ac‐ celerator and let the vehicle roll. The flow of fuel is interrupted while coasting.
Switch off the engine during longer stops Switch off the engine during longer stops, e.g., at traffic lights, railroad crossings or in traffic congestion. Fuel savings are achieved after the vehicle is switched off for only approx. 4 seconds.
Switch off any functions that are not currently needed Functions such as seat heating and the rear win‐ dow defroster require a lot of energy and con‐ sume additional fuel, especially in city and stop- and-go traffic. Therefore, switch off these functions if they are not actually needed.
Have maintenance carried out Have vehicles maintained regularly to achieve optimal vehicle economy and operating life. Have the maintenance carried out by your serv‐ ice center.
Saving fuel
Driving tips
Please also note the BMW Maintenance Sys‐ tem, refer to page 277.
ECO PRO The concept ECO PRO supports a driving style that saves on fuel consumption. For this purpose, the engine control and comfort functions, e. g. the climate control output, are adjusted. In addition, context-sensitive instructions can be displayed that assist in driving in a manner that optimizes fuel consumption. The extension of the range that is achieved as a result can be displayed in the instrument cluster. Activating ECO PRO
Press button repeatedly until ECO PRO is displayed in the instrument cluster.
Display in the instrument cluster ECO PRO bonus range
An extension of the range can be achieved by an adjusted driving style. This may be displayed as the bo‐ nus range in the instrument clus‐
ter. Driving style
In the tachometer, a mark in the bar display indicates the current efficiency of the driving style cor‐ responding to the accelerator pedal position.
▷ Blue display: efficient driving style as long as
the mark moves within the blue range.
▷ Gray display: adjust driving style, e. g. by
backing off the accelerator pedal.
Online Edition for Part no. 01 40 2 608 633 - 11 09 490
163
Driving tips
Saving fuel
The display switches to blue as soon as all con‐ ditions for fuel-economy-optimized driving are met. ECO PRO Tip - driving instruction
The arrow indicates that the driv‐ ing style can be adjusted to be more fuel efficient by backing off the accelerator.
Additional symbols
Symbol Measure
For efficient driving style, back off the accelerator.
Reduce speed to the selected ECO PRO speed.
Automatic transmission: switch from S to D or avoid manual shift interven‐ tions. Manual shift transmission: follow shifting instructions.
Manual shift transmission: engage neutral for engine stop.
Configuring ECO PRO 1. "Settings" 2. "Driving mode" 3. "Configure ECO PRO" 4. Configure the program.
ECO PRO Tip ▷ "ECO PRO limit:":
Set ECO Pro speed at which an ECO PRO Tip is to be displayed.
▷ "ECO PRO speed warning":
A reminder is displayed if the set ECO PRO speed is exceeded.
ECO PRO climate control "ECO PRO climate control" The climate control is adjusted to be fuel-effi‐ cient. The following settings are optimized: ▷ Cooling or heat output of the automatic cli‐
mate control
▷ Exterior mirror heating ▷ Seat heating ECO PRO Potential The percentage of potential savings that can be achieved with the current configuration is dis‐ played. Indications on the Control Display EfficientDynamics Information on fuel consumption and technol‐ ogy can be displayed during driving. 1. "Vehicle Info" 2. "EfficientDynamics" Displaying fuel consumption history The average fuel consumption can be displayed within an adjustable time frame.
"Consumption history"
Adjusting fuel consumption history time frame
Select the symbol.
164
Online Edition for Part no. 01 40 2 608 633 - 11 09 490
Saving fuel
Driving tips
Resetting fuel consumption history 1. "Options" Open. 2. "Reset consumption history" Displaying EfficientDynamics info The current efficiency can be displayed.
"EfficientDynamics Info"
The following systems are displayed: ▷ Automatic engine start/stop function. ▷ Energy recovery. ▷ Climate control output.
Online Edition for Part no. 01 40 2 608 633 - 11 09 490
165
Online Edition for Part no. 01 40 2 608 633 - 11 09 490
Navigation
This chapter contains various examples of how the navigation system can guide you reliably to your destination.
Online Edition for Part no. 01 40 2 608 633 - 11 09 490
Navigation
Navigation system
Navigation system Vehicle equipment All standard, country-specific and optional equipment that is offered in the model series is described in this chapter. Therefore, equipment is also described that is not available in a vehicle, e. g., because of the selected optional equip‐ ment or country variant. This also applies for safety-related functions and systems.
General information The navigation system can determine the pre‐ cise position of the vehicle, with the aid of sat‐ ellites and vehicle sensors, and can reliably guide you to every entered destination. Navigation data are stored in the vehicle and can be updated.
Entries in stationary vehicle Enter data only when the vehicle is sta‐
tionary, and always give priority to the applicable traffic regulations in the event of any contradic‐ tion between traffic and road conditions and the instructions issued by the navigation system. Failure to take to this precaution can place you in violation of the law and put vehicle occupants and other road users in danger.◀
Starting navigation system
Press the button on the controller.
1. 2. "Navigation"
The navigation system can also be ac‐ cessed directly with the button on the con‐
troller.
Destination input Manual destination entry General information The system supports you in entering street names and house numbers by automatically completing the entry and providing entry com‐ parisons, refer to page 22. Stored town/city and street names can be called up quickly. ▷ If the existing entries should not be changed, the entries for the state/province and town/ city can be skipped.
▷ Destination guidance is started to the town/
city center if no street is entered.
Entering a state/province 1. "Navigation" 2. "Enter address"
3. Select "State/Province" or the displayed
state/province.
168
Online Edition for Part no. 01 40 2 608 633 - 11 09 490
Entering a town/city 1. Select "Town/City/Postal Code" or the dis‐
played town/city.
2. Select letters, if necessary.
The list is narrowed down further with each entry.
3. Move the controller to the right. 4. Select the town/city name from the list. If there are several towns/cities with the same name: 1. Change to the list of town/city names. 2. Highlight the town/city. 3. Select the town/city. Entering the postal code 1. Select "Town/City/Postal Code" or the dis‐
played town/city.
Navigation system Navigation
3. Select the street. Alternative: enter the street address and house number 1. Select "Street" or the displayed street. 2. Enter the street as you would the town/city. 3. "House number" 4. Select the numbers. 5. Change to the list of house numbers. 6. Select a house number or range of house
numbers.
Street does not exist in the destination city/town The desired street does not exist in the specified city/town because it belongs to another part of the city/town. 1. "Navigation" 2. "Enter address" 3. Select "Street" or the displayed street. 4. Change to the list of street names. 5. Select "In" the displayed country.
All streets of the selected state/province are offered. The associated town/city is dis‐ played after the street name.
Select the symbol.
2. 3. Select the numbers. 4. Change to the list of postal codes and towns/
cities.
5. Highlight the entry. 6. Selecting an entry. Entering a street and intersection 1. Select "Street" or the displayed street. 2. Enter a street and intersection in the same
way as you would enter a town/city.
If there are several streets with the same name: 1. Change to the list of street names. 2. Highlight the street.
6. Select the letters. 7. Change to the list of street names. 8. Highlight the street. 9. Select the street.
Online Edition for Part no. 01 40 2 608 633 - 11 09 490
169
Navigation
Navigation system
Starting destination guidance after entering the destination 1. "Accept destination" 2. "Start guidance" or "Add as another
destination" Add, refer to page 175, a destination as a further destination.
Address book Selecting a destination from the address book 1. "Navigation" 2. "Address book"
Contacts with addresses are displayed if these have been checked as destinations. If the mobile phone does not display the contacts with addresses, they must first be checked as a destination, refer to page 248.
5. "Store as new contact" or "Add to existing
contact"
6. Select an existing contact, if available. 7. "Business address" or "Home address" 8. Enter "Last name" and, if necessary, "First
name".
9. "Store in vehicle" Storing the position The current position can be stored in the ad‐ dress book. 1. "Navigation" 2. "Options" Open. 3. "Store position as contact" or "Add position
to contact"
3. Select a contact in the list or, if desired, with
"A-Z search".
4. "Business address" or "Home address" Storing the destination in the address book After entering the destination, store the desti‐ nation in the address book. 1. "Navigation" 2. "Map" 3. 4. "Options" Open.
"Guidance"
4. Depending on the selection, choose an ex‐ isting contact from the list. Select the type of address and enter the first and last names.
5. "Store in vehicle" Editing or deleting an address 1. "Navigation" 2. "Address book"
170
Online Edition for Part no. 01 40 2 608 633 - 11 09 490
3. Highlight the entry. 4. "Options" Open. 5. "Edit in Contacts" or "Delete entry" Using the home address as the destination The home address must be stored. Specify the home address, refer to page 247. 1. "Navigation" 2. "Address book" 3. "Home"
4. "Start guidance" Last destinations At a glance The destinations previously entered are stored automatically. The destinations can be called up and used as a destination for destination guidance. Calling up the last destination 1. "Navigation" 2. "Last destinations"
Navigation system Navigation
Starting destination guidance 1. "Navigation" 2. "Last destinations" 3. Select the destination. 4. "Start guidance" Editing the destination 1. "Navigation" 2. "Last destinations" 3. Highlight the destination. 4. Open "Options". 5. "Edit destination" Deleting the last destinations 1. "Navigation" 2. "Last destinations" 3. Highlight the destination. 4. Open "Options". 5. "Delete entry" or "Delete all last
destinations"
Special destinations General information Even with the most current navigation data, in‐ formation regarding particular individual desti‐ nations may have changed. For instance, certain gas stations may not be operating. Opening the search for special destinations To select special destinations, e.g., hotels or tourist attractions: 1. "Navigation" 2. "Points of Interest" 3. Select the search function.
Online Search 1. "Google™ Local Search" 2. Select a special destination.
Online Edition for Part no. 01 40 2 608 633 - 11 09 490
171
Navigation
Navigation system
Select the symbol.
3. 4. "Start guidance"
A-Z search 1. "A-Z search" 2. "Town/City"
Select or enter the town/city.
3. "Category" 4. Select the category. 5. "Category details"
For some special destinations, multiple cat‐ egory details can be selected. Move the controller to the left to leave the category details.
6. "Keyword" 7. Enter the keyword.
A list of the special destinations is displayed.
8. Select a special destination.
Details are displayed. If multiple details are stored, you can leaf through the pages. If a phone number is available, a connection can be established if necessary.
9.
Select the symbol.
"Start guidance" or "Add as another destination" Add, refer to page 175, a destination as a further destination.
"Start search": if a search term is not entered, the search is repeated with the previous search term.
Category search 1. "Category search" 2. "Town/City"
Select or enter the town/city.
3. "Category" 4. Select the category. 5. "Category details"
For some special destinations, multiple cat‐ egory details can be selected. Move the controller to the left to leave the category details.
6. "Start search"
A list of the special destinations is displayed.
7. Select a special destination.
Details are displayed. If multiple details are stored, you can leaf through the pages. If a phone number is available, a connection can be established if necessary.
8.
Select the symbol.
"Start guidance" or "Add as another destination" Add, refer to page 175, a destination as a further destination.
Display of special destinations List of special destinations: special destinations are organized by distance and are displayed with a directional arrow to the special destination. On the split screen, special destinations of the selected category are displayed in the map view as symbols. The display depends on the scale of the map and the category. Destination entry via BMW Assist A connection is established to the Concierge service, refer to page 251. 1. "Navigation" 2. "Enter address" 3. "Options" Open. 4. "BMW Assist dest. entry"
172
Online Edition for Part no. 01 40 2 608 633 - 11 09 490
Displaying special destinations in the map To display symbols of the special destinations in the map view: 1. "Navigation" 2. "Map" 3. "Options" Open. 4. "Display Points of Interest" 5. Select the setting. Destination entry by map Selecting the destination 1. "Navigation" 2. "Map"
The current position of the vehicle is indi‐ cated on the map.
3.
"Interactive map"
Navigation system Navigation
Additional functions Additional functions are available on the inter‐ active map after the controller is pressed.
▷
Select the symbol.
"Start guidance" or "Add as another destination"
▷ "Exit interactive map": return to the map
view.
▷ "View in northern direction" or "View in
driving direction"
▷ "Display destination": the map section
around the destination is displayed.
▷ "Display current location": the map section around your current location is displayed.
4. Select the destination with crosshairs.
▷ To change the scale: turn the controller. ▷ To shift the map: move the controller in
the required direction.
▷ To shift the map diagonally: move the controller in the required direction and turn it.
Specifying the street If the system does not recognize a street, one of the following is displayed: ▷ The name of a street nearby. ▷ The county. ▷ The coordinates of the destination.
▷ "Find points of interest": the search for spe‐
cial destinations is started. Destination entry by voice General information ▷ Instructions for voice activation system, re‐
fer to page 23.
▷ When making a destination entry by voice, you can change between voice operation and iDrive.
▷ To have the available spoken instructions
read out loud: ›Voice commands‹
Saying the entries ▷ The town/city, street, and house number
can be entered as a single command.
▷ Countries, towns and cities, streets, and in‐ tersections can be said as whole words or
Online Edition for Part no. 01 40 2 608 633 - 11 09 490
173
Navigation
Navigation system
spelled in the language of the system. Set the language, refer to page 84. Example: to enter a town/city in a US state as a whole word, the language of the system must be English.
▷ Spell the entry if the spoken language and
the language of the system differ.
▷ Say the letters smoothly, and avoid exag‐ gerating the pronunciation and inserting lengthy pauses between the letters.
▷ The options available for entering data de‐ pend on the navigation data and the country and language settings.
Entering an address in a command
1.
Press the button on the steering
wheel. ›Enter address‹
2. 3. Wait for a request from the system. 4. Say the address in the suggested order. 5. Continue making the entry as prompted by
the system.
If necessary, individually name the separate components of the address, e.g., the town/city. Entering a town/city separately The name of the town/city can be said as a word or spelled out. With the destination entry menu displayed:
1.
Press the button on the steering
wheel. ›City‹ or ›Spell city‹.
2. 3. Wait for the system to prompt you for the
town/city.
4. Say the name of the town/city, or say at least
the first three letters. Depending on the entry, up to 20 towns/cit‐ ies may be suggested.
5. Select the town/city.
▷ To select a recommended town/
city: ›Yes‹
▷ To select a different town/city: ›New
entry‹
▷ Select an entry: ›Entry ...‹ e.g., entry 2
▷ To spell an entry: ›Spell city‹6. Continue making the entry as prompted by
the system.
If there are several towns/cities with the same name: Towns/cities of the same name are grouped in a list and displayed as one location followed by an ellipsis. 1. Select an entry: ›Yes‹ or ›Entry ...‹ e.g., en‐
try 2.
2. Select the desired town/city.
